User`s guide | Brother NC8100H Network Card User Manual

version B
Multi-Protocol Print / Fax Server
NC-8100h
USER’S GUIDE
Please read this manual thoroughly before using the printer. You can print or view this manual
from the CD-ROM (supplied with your FAX/MFC) at any time, please keep the CD-ROM in a
convenient place for quick and easy reference at all times.
i
Trademarks
Brother is a registered trademark of Brother Industries, Ltd.
HP, HP/UX, JetDirect and JetAdmin are trademarks of Hewllet-Packard Company.
UNIX is a trademarks of UNIX Systems Laboratories.
Ethernet is trademark of Xerox Corporation.
Postscript is trademark of Adobe Systems Incorporated.
NetWare is a trademark of Novell, Inc.
Apple, Macintosh, LaserWriter, and AppleTalk are trademarks of Apple Computer, Inc.
IBM, LAN Server, and AIX are trademarks of International Business Machines Corporation.
LAN Manager, Windows, and MS-DOS are trademarks of Microsoft Corporation.
NC-8100h and BRAdmin are trademarks of Brother Industries Ltd.
All other brand and product names mentioned in this user’s guide are registered trademarks or
trademarks of respective companies.
Compilation and Publication
Under the supervision of Brother Industries Ltd., this manual has been compiled and
published, covering the latest product descriptions and specifications.
The contents of this manual and the specifications of this product are subject to change
without notice.
Brother reserves the right to make changes without notice in the specifications and materials
contained herein and shall not be responsible for any damages (including consequential)
caused by reliance on the materials presented, including but not limited to typographical and
other errors relating to the publication.
©2002 Brother Industries Ltd.
Shipment of the print server
If for any reason you must ship your print server, carefully package the print server to avoid any
damage during transit. It is recommended that you save and use the original packaging. The print
server should also be adequately insured with the carrier.
WARNING
When shipping the print server, put it into the anti-static bag to avoid damage.
ii
Multi-Protocol Print / Fax Server
NC-8100h
USER’S GUIDE
For technical and operational assistance, please visit the Brother web site on http://solutions.brother.com
If you have comments or suggestions, please write us at:
In Europe
European Technical Services
1 Tame Street
Audenshaw
Manchester, M34 5JE
UK
In USA
Printer Customer Support
Brother International Corporation
100 Somerset Corporate Blvd.
Bridgewater, NJ 08807
In CANADA
Brother International Corporation (Canada), Ltd.
- Marketing Dept.
1, rue Hôtel de Ville
Dollard-des-Ormeaux, PQ, Canada H9B 3H6
Brother fax-back system (USA Only)
Brother Customer Service has installed an easy to use fax-back system so you can get instant answers to
common technical questions and product information for all Brother products. This is available 24 hours a
day, 7 days a week. You can use the system to send the information to any fax machine, not just the one
you are calling from.
Please call 1-800-521-2846 and follow the voice prompts to receive faxed instructions on how to use the
system and your index of fax-back subjects.
DEALERS/SERVICE CENTERS (USA only)
For the name of an authorized dealer or service center, call 1-800-284-4357.
SERVICE CENTERS (Canada only)
For service center addresses in Canada, call 1-877-BROTHER
INTERNET ADDRESS
For technical questions and downloading drivers: http://solutions.brother.com
iii
Introduction
Overview
The Brother NC-8100h Print / Fax Server allows your Brother FAX/MFC to be
attached and shared on a 10/100Mbit Ethernet Network. Web Based Management
and Administration utilities provide easy configuration and management of your
Brother FAX/MFC. Once installed and configured, the NC-8100h allows your
FAX/MFC machine to FAX documents over the Internet; print and scan documents
over a network. The NC-8100h is even supplied with Brother’s Peer to Peer printing
software allowing you to easily share the machine as a small department printer.
Features
Internet Fax
The Brother FAX/MFC can be assigned an E-mail address allowing you to send,
receive and forward documents on a Local Area Network and the Internet to PC’s or
other Internet Fax machines.
Network Printing
The Print / Fax server can be utilized as a print server providing printing services for
the Windows 95/98/Me, Windows NT4.0/2000/XP, Unix Systems supporting the
TCP/IP protocols, Novell Operating Systems supporting IPX/SPX and Macintosh
Networks supporting AppleTalk.
Network Scanning
You can scan documents into the Brother FAX/MFC and then E-mail them to your
PC for editing in Black & White or Color.
Management Utilities
The Web Based Management and BRAdmin Professional utilities provide powerful
easy to use management of Fax, network and E-mail settings.
iv
TABLE OF CONTENTS
Overview ........................................................................................................................................... iv
Features ............................................................................................................................................. iv
IMPORTANT INFORMATION: REGULATIONS........................................................................ xiii
Federal Communications Commission (FCC) Declaration of Conformity (For U.S.A. only) ....... xiii
Declaration of Conformity (Europe) ............................................................................................... xiv
CHAPTER ONE TCP/IP Configuration Assigning TCP/IP Information ...... 1-1
Overview............................................................................................................................................. 1-1
Using the FAX/MFC front panel to allocate an IP address ............................................................ 1-2
Using BRAdmin and the TCP/IP Protocol to set the IP address ................................................... 1-2
Using BRAdmin and the IPX/SPX Protocol to set the IP address................................................. 1-3
Changing the IP Address using the BRAdmin application ............................................................ 1-4
Using DHCP to Configure the IP address........................................................................................ 1-5
Using ARP to Configure the Print / Fax server IP Address............................................................ 1-6
Using RARP to Configure the IP Address ....................................................................................... 1-7
Using BOOTP to Configure the IP Address .................................................................................... 1-8
Changing the IP Address settings with the TELNET Console....................................................... 1-9
CHAPTER TWO Front Panel Setup Menu ........................................................ 2-1
LAN Main Setup Menu ..................................................................................................................... 2-1
1-Setup TCP/IP .................................................................................................................................. 2-1
1-BOOT METHOD ......................................................................................................................... 2-1
2-IP ADDRESS ............................................................................................................................... 2-3
3-SUBNET MASK.......................................................................................................................... 2-4
4-GATEWAY ................................................................................................................................... 2-4
5-HOST NAME............................................................................................................................... 2-5
6-WINS Configuration .................................................................................................................... 2-5
7-WINS SERVER............................................................................................................................ 2-5
8-DNS SERVER.............................................................................................................................. 2-6
2-Setup Internet ................................................................................................................................. 2-6
1-MAIL ADDRESS......................................................................................................................... 2-6
2-SMTP SERVER ........................................................................................................................... 2-8
3-POP3 SERVER............................................................................................................................. 2-8
4-MAILBOX NAME....................................................................................................................... 2-8
5-MAILBOX PWD.......................................................................................................................... 2-9
3-Setup Mail RX ................................................................................................................................ 2-9
1-AUTO POLLING ......................................................................................................................... 2-9
2-POLL FREQUENCY ................................................................................................................... 2-9
3-HEADER...................................................................................................................................... 2-9
v
4-DEL ERROR MAIL................................................................................................................... 2-10
5-NOTIFICATION ........................................................................................................................ 2-10
4-Setup Mail TX............................................................................................................................... 2-10
1-SENDER SUBJECT................................................................................................................... 2-10
2-SIZE LIMIT ............................................................................................................................... 2-11
3-NOTIFICATION ........................................................................................................................ 2-11
5-Setup Relay ................................................................................................................................... 2-12
1-RLY BROADCAST.................................................................................................................... 2-12
2-RELAY DOMAIN...................................................................................................................... 2-12
3-RELAY REPORT ....................................................................................................................... 2-12
6-Setup Misc..................................................................................................................................... 2-13
1-NETWARE................................................................................................................................. 2-13
2-NET FRAME ............................................................................................................................. 2-13
3-APPLETALK ............................................................................................................................. 2-13
4-DLC/LLC ................................................................................................................................... 2-13
5-NETBIOS/IP .............................................................................................................................. 2-14
6-ETHERNET ............................................................................................................................... 2-14
7-TIME ZONE .............................................................................................................................. 2-14
User Setting List .............................................................................................................................. 2-15
CHAPTER THREE Web Based Management How to Use the Web-Based
Management Utility ................................................................................................ 3-1
Overview............................................................................................................................................. 3-1
How to Connect Using a Browser..................................................................................................... 3-2
Password Information ....................................................................................................................... 3-2
CHAPTER FOUR Internet FAX .......................................................................... 4-1
Overview............................................................................................................................................. 4-1
Getting Connected ........................................................................................................................... 4-2
Front Panel Key Functions .............................................................................................................. 4-2
Sending an Internet Fax .................................................................................................................... 4-3
Entering Text ................................................................................................................................... 4-4
Receiving E-mail or Internet Fax ..................................................................................................... 4-6
Receiving an Internet Fax to a PC ................................................................................................... 4-7
Forwarding Received E-mail and Fax Messages............................................................................. 4-7
Relay Broadcasting............................................................................................................................ 4-8
Relay Broadcast from a FAX/MFC ................................................................................................. 4-9
Relay Broadcast from a PC ........................................................................................................... 4-10
TX Verification Mail ........................................................................................................................ 4-11
vi
Setup Mail (TX) ............................................................................................................................... 4-11
Setup Mail (RX) ............................................................................................................................... 4-11
Error mail......................................................................................................................................... 4-12
Important information on Internet Fax......................................................................................... 4-12
Using Scan to E-mail ....................................................................................................................... 4-13
Entering Text ................................................................................................................................. 4-14
CHAPTER FIVE TCP/IP Printing Printing from Windows® NT,
Windows® 2000 or Windows® XP LAN Server and Warp Server....................... 5-1
Overview............................................................................................................................................. 5-1
Quick Tips: ...................................................................................................................................... 5-1
®
Windows NT 3.5x/NT 4.0/2000/XP (TCP/IP) Configuration........................................................ 5-2
®
®
Windows 2000 Windows XP Printing (Printer Driver not yet installed) ................................... 5-3
Standard TCP/IP Port Printing......................................................................................................... 5-3
®
®
IPP Printing from Windows 2000 and Windows XP Clients....................................................... 5-4
®
IPP printing from Windows 95/98/Me Clients............................................................................... 5-4
®
®
Windows 2000 Windows XP Printing
(Printer Driver already installed)..................................................................................................... 5-4
®
Windows NT 4.0 Printing ................................................................................................................ 5-5
®
Windows NT 4.0 Printing
(Printer Driver not yet installed)...................................................................................................... 5-6
®
Windows NT 4.0 Printing
(Printer Driver already installed)..................................................................................................... 5-7
®
Windows NT 3.5x Printing .............................................................................................................. 5-8
®
Windows NT 3.5x Printing
(Printer Driver not yet installed)...................................................................................................... 5-8
Other Sources of Information........................................................................................................... 5-9
CHAPTER SIX Peer to Peer Printing
How to Print in a Windows® 95/98/Me Peer to Peer network ............................. 6-1
Overview............................................................................................................................................. 6-1
Quick Tips: ...................................................................................................................................... 6-1
TCP/IP Printing................................................................................................................................. 6-2
Installing the Brother Peer to Peer Software .................................................................................. 6-3
Associating to the printer.................................................................................................................. 6-4
Adding a Second Brother LPR Port................................................................................................. 6-4
vii
Other Sources of Information........................................................................................................... 6-5
CHAPTER SEVEN NetBIOS Peer to Peer Printing How to Printing using
NetBIOS on Windows® 95/98/Me/NT®/2000/XP ................................................... 7-1
Overview............................................................................................................................................. 7-1
Quick Tips: ...................................................................................................................................... 7-1
Print / Fax Server Configuration...................................................................................................... 7-2
Changing the workgroup/domain name using TELNET or BRCONFIG or a web browser ...... 7-3
®
®
NetBIOS Port Monitor for Windows 95/98/Me, NT 4.0/2000/XP................................................ 7-4
Installing the Brother NetBIOS Port Monitor ................................................................................ 7-4
Associating the printer ...................................................................................................................... 7-5
®
Windows 95/98/Me ........................................................................................................................ 7-5
®
®
Windows NT 4.0/2000/XP ........................................................................................................... 7-5
Adding a Second NetBIOS Print Port.............................................................................................. 7-6
®
Windows 95/98/Me ........................................................................................................................ 7-6
®
®
Windows NT 4.0/2000/XP ........................................................................................................... 7-6
CHAPTER EIGHT How to Configure Internet Printing for Windows®
95/98/Me/NT®4.0/ 2000/XP Internet Printing Installation ................................ 8-1
Overview............................................................................................................................................. 8-1
Quick Tips: ...................................................................................................................................... 8-1
Brother Internet Print General Information................................................................................... 8-2
Brother Internet Print Configuring the Brother Print / Fax server .............................................. 8-3
Print / Fax server Configuration Checklist ...................................................................................... 8-3
Brother Internet Print Using BRAdmin to Configure the Print / Fax server............................... 8-4
Brother Internet Print Using a Web Browser to configure the Print / Fax server ....................... 8-5
Brother Internet Print Using TELNET to Configure the Print / Fax server ................................ 8-6
®
®
Brother Internet Print Installing the BIP software on Windows 95/98/Me/NT 4.0/2000/XP ... 8-7
Setup from CD-ROM ...................................................................................................................... 8-7
Adding a Second Brother Internet Port......................................................................................... 8-10
®
Windows 2000/XP IPP Printing.................................................................................................... 8-11
Specifying a different URL ............................................................................................................. 8-12
CHAPTER NINE Novell NetWare Printing How to configure
Novell NetWare Printing ........................................................................................ 9-1
Overview............................................................................................................................................. 9-1
Quick Tips: ...................................................................................................................................... 9-1
viii
General Information.......................................................................................................................... 9-2
Creating a NDPS Printer Using NWADMIN for NetWare5........................................................... 9-3
NDPS Manager .................................................................................................................................. 9-3
NDPS Broker...................................................................................................................................... 9-3
Creating a Printer Agent................................................................................................................... 9-4
Configuring Netware 3 and NetWare 4 systems.............................................................................. 9-5
Configuring the Brother Print / Fax server (Queue Server Mode in Bindery emulation
mode) using BRAdmin ...................................................................................................................... 9-6
Configuring the Brother Print / Fax server (Queue Server Mode in NDS mode) using
BRAdmin............................................................................................................................................ 9-7
Configuring the Brother Print / Fax server (Queue Server Mode in NDS mode) using
Novell NWADMIN and BRAdmin.................................................................................................... 9-8
Configuring the Brother Print / Fax server (Remote Server Mode in NDS mode) using
Novell NWAdmin and BRAdmin.................................................................................................... 9-10
Configuring the Brother Print / Fax server (Queue Server Mode in Bindery emulation
mode) using PCONSOLE and BRCONFIG.................................................................................. 9-12
Configuring the Brother Print / Fax server (Queue Server Mode in NDS mode) using
PCONSOLE and BRCONFIG ....................................................................................................... 9-14
Configuring the Brother Print / Fax server (Remote Printer Mode using PCONSOLE
and BRCONFIG .............................................................................................................................. 9-16
CHAPTER TEN Printing From a Macintosh® .................................................. 10-1
For Mac OS 8.6 – 9.2 ....................................................................................................................... 10-1
System Requirements .................................................................................................................... 10-1
Printer Driver Installation .............................................................................................................. 10-1
Printer Driver Selection ................................................................................................................ 10-2
For Mac OS 10.1 .............................................................................................................................. 10-3
System Requirements .................................................................................................................... 10-3
Printer Driver Installation .............................................................................................................. 10-3
Printer Driver Selection ................................................................................................................. 10-3
CHAPTER ELEVEN DLC Printing Printing from Windows® NT® or
Windows® 2000 ...................................................................................................... 11-1
Overview........................................................................................................................................... 11-1
Quick Tips: .................................................................................................................................... 11-1
®
®
Configuring DLC on Windows NT /2000..................................................................................... 11-2
®
Windows 2000 Printer Setup......................................................................................................... 11-3
®
®
Windows NT 4.0 Printer Setup.................................................................................................... 11-4
ix
®
®
Windows NT 3.5x Setup ............................................................................................................... 11-5
Configuring DLC on Other Systems .............................................................................................. 11-5
CHAPTER TWELVE Unix Printing Printing from Unix/Linux using
TCP/IP ................................................................................................................... 12-1
Overview........................................................................................................................................... 12-1
Quick Tips: .................................................................................................................................... 12-1
TCP/IP.............................................................................................................................................. 12-2
General TCP/IP UNIX Host Configuration .................................................................................. 12-3
Linux Configuration........................................................................................................................ 12-6
HP/UX Configuration...................................................................................................................... 12-7
IBM RS/6000 AIX Configuration................................................................................................... 12-8
Sun Solaris 2.x Configuration......................................................................................................... 12-9
SCO UNIX Configuration............................................................................................................. 12-10
DEC TCP/IP Servers for VMS(UCX) .......................................................................................... 12-11
TGV's Multinet .............................................................................................................................. 12-11
Wollongong's PATHWAY .............................................................................................................. 12-11
IBM/AS4000................................................................................................................................... 12-11
Other Systems ................................................................................................................................ 12-12
CHAPTER THIRTEEN Troubleshooting ......................................................... 13-1
Overview........................................................................................................................................... 13-1
Installation problems....................................................................................................................... 13-2
Intermittent Problems ..................................................................................................................... 13-5
TCP/IP Troubleshooting.................................................................................................................. 13-6
UNIX Troubleshooting .................................................................................................................... 13-7
®
®
Windows NT /LAN Server (TCP/IP) Troubleshooting ............................................................... 13-9
®
Windows 95/98/Me Peer to Peer Print (LPR) Troubleshooting.................................................. 13-9
®
Windows 95/98/Me Peer-to-Peer (HP JetAdmin compatible method) Troubleshooting ........ 13-10
®
®
Windows 95/98/Me/NT 4.0 Peer-to-Peer Print (NetBIOS) Troubleshooting.......................... 13-10
Brother Internet Print (TCP/IP) Troubleshooting ...................................................................... 13-11
x
®
Windows 95/98/Me/2000/XP FTP/IPP Troubleshooting ........................................................... 13-12
Novell NetWare Troubleshooting.................................................................................................. 13-13
AppleTalk Troubleshooting ........................................................................................................... 13-14
DLC/LLC Troubleshooting ........................................................................................................... 13-15
Web Browser Troubleshooting (TCP/IP) ..................................................................................... 13-15
Internet Fax Troubleshooting ....................................................................................................... 13-16
CHAPTER FOURTEEN Brother Network PC Fax Software
Installing and using the Brother Network PC Fax Software ............................ 14-1
Overview........................................................................................................................................... 14-1
Quick Tips: .................................................................................................................................... 14-1
Installing Network PC Fax ............................................................................................................. 14-2
Setting Up User Information .......................................................................................................... 14-3
Setting Up Sending Information..................................................................................................... 14-4
Setting Up Speed Dial...................................................................................................................... 14-5
Setting Up a Group for Broadcasting ............................................................................................ 14-7
Sending a File as a PC FAX Using the Simple Style ..................................................................... 14-9
Sending a File as a PC FAX using the Facsimile Style................................................................ 14-10
Updating other FAX/MFC’s through the Network..................................................................... 14-11
®
Sending a Fax from Your Macintosh Application...................................................................... 14-13
CHAPTER FIFTEEN Brother BFP Software
Brother Internet Fax Printing Software ............................................................. 15-1
Overview........................................................................................................................................... 15-1
Installing Brother Internet Fax Printing Driver ........................................................................... 15-2
Changing the BFP Port Settings..................................................................................................... 15-4
Relay Broadcast Function............................................................................................................... 15-6
®
®
Uninstalling from Windows 95/98/Me/NT 4.0/2000 .................................................................... 15-7
Using the BFP Address Book .......................................................................................................... 15-9
Setting Up a Group for Broadcasting .......................................................................................... 15-11
Sending a Network Fax with BFP ................................................................................................ 15-13
xi
Appendix A Appendix ........................................................................................... A-1
General Information......................................................................................................................... A-1
Appendix B Using Services................................................................................... A-3
General .............................................................................................................................................. A-3
Appendix C Reloading the Print / Fax Server Firmware.................................. A-4
General .............................................................................................................................................. A-4
Reloading firmware using BRAdmin.............................................................................................. A-5
Reloading using the FTP Protocol from a command prompt ....................................................... A-6
Reloading using the FTP Protocol from a Web Browser............................................................... A-7
Appendix D Specifications and Function Table.................................................. A-8
Specifications..................................................................................................................................... A-8
INDEX ........................................................................................................................................ Index-1
xii
IMPORTANT INFORMATION: REGULATIONS
Federal Communications Commission (FCC) Declaration of Conformity
(For U.S.A. only)
Responsible Party:
Brother International Corporation
100 Somerset Corporate Boulvard
Bridgewater, NJ 09907-0911, USA
TEL: (908) 704-1700
declares, that the products
Product Name:
Model Number:
Brother Network Card (BR-net)
NC-8100h
complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undersired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Important
Changes or modifications not expressly approved by Brother Industries, Ltd. could void the
user’s authority to operate the equipment.
xiii
Industry Canada Compliance Statement (For Canada only)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du Canada.
Declaration of Conformity (Europe)
We,
Brother Industries, Ltd.,
15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan
declare that this product is in conformity with the following normative documents.
Safety:
EMC:
EN 60950,
EN 55022 Class B, EN 55024
following the provisions of the Low Voltage Directive 73/23/EEC and the Electromagnetic
Compatibility Directive 89/336/EEC (as amended by 91/263/EEC and 92/31/EEC).
Issued by:
Brother Industries, Ltd.
Information & Document Company
xiv
CHAPTER 1 TCP/IP CONFIGURATION
CHAPTER ONE
11
1
TCP/IP Configuration
Assigning TCP/IP Information
Overview
The TCP/IP protocol requires that each device on the network have it's own
unique IP address. Use the following information to learn about IP address
configuration.
By default Brother Print / Fax servers have a sample IP address of 192.0.0.192,
however, you can easily change this IP address number to match with the IP
address details of your network. This can be done in any of the following ways:
1. FAX/MFC front panel setting.
®
®
2. BRAdmin application (for Windows 95/98/Me/NT 4.0/2000/XP using
the IPX/SPX or TCP/IP protocol).
3. DHCP, Reverse ARP (rarp) or BOOTP.
4. The ARP command.
5. Brother BRCONFIG NetWare utility (A Novell Network is necessary).
Other ways to CHANGE the IP address once it is already set:
1.
2.
3.
4.
FAX/MFC front panel
TELNET
HTTP (Web browser)
Other SNMP based management utility
These configuration methods are described in the following paragraphs.
The IP address you assign to the Print / Fax server must be on the same logical
network as your host computers, if it is not, you must properly configure the
subnet mask and the router (gateway).
1-1
CHAPTER 1 TCP/IP CONFIGURATION
Using the FAX/MFC front panel to allocate
an IP address
Refer to chapter 2 for details on how to configure IP address information using
the FAX/MFC control panel. By using the front panel of the FAX/MFC, you can
program the IP address details at the same time that other FAX/MFC parameters
are configured.
Using BRAdmin and the TCP/IP Protocol
to set the IP address
If your PC has only the TCP/IP protocol, do the following:
1. Select TCP/IP filter in the left frame of the main window.
2. Select the "Device" menu and choose the "Search Active Devices".
If the Print / Fax server is set to its factory default settings, it will not appear in
the BRAdmin screen, however, when you select the "Search Active Devices"
option, it will be found as an un-configured device.
3. Select the "Device" menu and choose the "Setup Unconfigured Device".
4. Select the MAC address of your Print / Fax server and click the
Configure button.
You can find the node name and MAC address by printing out the FAX/MFC
configuration page. Refer to the Quick Setup Guide for information on how to
print the configuration page on your Print / Fax server.
5. Input the IP address, Subnet mask and Gateway (If needed) of your Print
/ Fax server.
6. Click OK then select Close.
7. With the correctly programmed IP address, you will see the Brother
Print / Fax server in the device list.
1-2
CHAPTER 1 TCP/IP CONFIGURATION
Using BRAdmin and the IPX/SPX Protocol
to set the IP address
If your PC has Novell Netware Client software and is using the IPX/SPX
protocol, do the following:
1. Select IPX/SPX filter in the left frame of the main window.
2. Check the Print / Fax server name (the default node name will be
BRN_xxxxxx, where "xxxxxx" is the last six digits of the Ethernet
address (MAC address)).
If you cannot find your server name, select the "Device" menu and choose
"Search Active Devices" (you can also press the F4 key) and try again.
You can find the node name and MAC address by printing out the FAX/MFC
configuration page. Refer to the NC-8100h Quick Setup Guide for information
on how to print the configuration page on your Print / Fax server.
3. Select the Print / Fax server that you wish to configure and double click
it. You will be asked for a password. The default password is "access".
4. Select the TCP/IP tab and set the IP address, Subnet mask and Gateway
as needed.
5. Click OK.
1-3
CHAPTER 1 TCP/IP CONFIGURATION
Changing the IP Address using the
BRAdmin application
®
®
Start the BRAdmin application (from Windows 95/98/Me/NT 4.0/2000/XP).
The BRAdmin application can use the IPX/SPX or TCP/IP protocols to
communicate with the Brother Print / Fax server. As the default IP address of
Brother Print / Fax servers is 192.0.0.192, the Print / Fax server will probably be
incompatible with the IP address numbering scheme on your network. If you are
not using DHCP, BOOTP or RARP, you will want to change the IP address.
There are two ways that you can do this from within BRAdmin.
1. Use the IPX/SPX protocol
2. Use the TCP/IP protocol and let BRAdmin find the Brother Print / Fax
server. Double click the Print / Fax Server you wish to change the IP
Address and enter the password.
3. Select the TCP/IP tab and change the IP Address as necessary.
1-4
CHAPTER 1 TCP/IP CONFIGURATION
Using DHCP to Configure the IP address
Dynamic Host Configuration Protocol (DHCP) is one of several automated
mechanisms for IP address allocation. If you have a DHCP Server in your
®
®
network (typically a Unix, Windows NT /2000 or Novell Netware network) the
Print / Fax server will automatically obtains its IP address from DHCP server and
register its name with any RFC 1001 and 1002-compliant dynamic name services.
If you do not want your Print / Fax server configured via DHCP, BOOTP or
RARP, you must set the BOOT METHOD to static, this will prevent the Print /
Fax server from trying to obtain an IP address from any of these systems. To
change the BOOT METHOD, use the FAX/MFC’s front panel, TELNET (using
the SET IP METHOD command), Web browser or by using the BRAdmin
application.
1-5
CHAPTER 1 TCP/IP CONFIGURATION
Using ARP to Configure the Print / Fax
server IP Address
If you are unable to use the BRAdmin application, FAX/MFC front panel and
your network does not use a DHCP server, you can also use the ARP command.
ARP is the simplest method of configuring the Print / Fax server IP address. The
®
ARP command is available on Windows systems that have TCP/IP installed as
well as Unix systems. To use arp enter the following command the command prompt:
arp -s ipaddress ethernetaddress
Where ethernetaddress is the Ethernet address (MAC address) of the Print / Fax
server and ipaddress is the IP address of the Print / Fax server. For example:
®
Windows Systems
®
Windows Systems require the colon ":" character in-between each digit of the
Ethernet address.
arp -s 192.189.207.2 00:80:77:31:01:07
Unix Systems
Typically, Unix systems require the hash "-" character in-between each digit of
the Ethernet address.
arp -s 192.189.207.2 00-80-77-31-01-07
You must be on the same Ethernet segment (that is, there cannot be a router
between the Print / Fax server and operating system) to use the arp -s command.
If there is a router, you may use BOOTP or other methods described in this
chapter to enter the IP address.
If your Administrator has configured the system to deliver IP addresses using
BOOTP, DHCP or RARP your Brother Print / Fax server can receive an IP
address from any one of these IP address allocation systems, in which case, you
will not need to use the ARP command. The ARP command only works once.
For security reasons, once you have successfully configured the IP address of a
Brother Print / Fax server using the ARP command, you cannot use the ARP
command again to change the address. The Print / Fax server will ignore any
attempts to do this. If you wish to change the IP address again, use a Web
Browser, TELNET (using the SET IP ADDRESS command) the FAX/MFC’s
front panel or factory reset the Print / Fax server (which will then allow you to
use the ARP command again).
To configure the Print / Fax server and to verify the connection, enter the
following command ping ipaddress where the ipaddress is the IP address of the
Print / Fax server.
For example:
ping 192.189.207.2
1-6
CHAPTER 1 TCP/IP CONFIGURATION
Using RARP to Configure the IP Address
Brother Print / Fax server IP address can be configured using the Reverse ARP
(rarp) facility on your host computer. This is done by editing the /etc/ethers file
(if this file does not exist, you can create it) with an entry similar to the
following:
00:80:77:31:01:07
BRN_310107
Where the first entry is the Ethernet address of the Print / Fax server and the
second entry is the name of the Print / Fax server (the name must be the same as
the one you put in the /etc/hosts file).
If the rarp daemon is not already running, start it (depending on the system the
command can be rarpd, rarpd -a, in.rarpd -a or something else; type man rarpd or
refer to your system documentation for additional information). To verify that the
rarp daemon is running on a Berkeley UNIX-based system, type the following
command:
ps -ax | grep -v grep | grep rarpd
For AT&T UNIX-based systems, type:
ps -ef | grep -v grep | grep rarpd
The Brother Print / Fax server will get the IP address from the rarp daemon when
it is powered on.
1-7
CHAPTER 1 TCP/IP CONFIGURATION
Using BOOTP to Configure the IP Address
BOOTP is an alternative to rarp that has the advantage of allowing configuration
of the subnet mask and gateway. In order to use BOOTP to configure the IP
address make sure that BOOTP is installed and running on your host computer (it
should appear in the /etc/services file on your host as a real service; type man
bootpd or refer to your system documentation for information). BOOTP is
usually started up via the /etc/inetd.conf file, so you may need to enable it by
removing the "#" in front of the bootp entry in that file. For example, a typical
bootp entry in the /etc/inetd.conf file would be:
#bootp dgram udp wait /usr/etc/bootpd bootpd -i
Depending on the system, this entry might be called "bootps" instead of "bootp".
In order to enable BOOTP, simply use an editor to delete the "#" (if there is no
"#", then BOOTP is already enabled). Then edit the BOOTP configuration file
(usually /etc/bootptab) and enter the name, network type (1 for Ethernet),
Ethernet address and the IP address, subnet mask and gateway of the Print / Fax
server. Unfortunately, the exact format for doing this is not standardized, so you
will need to refer to your system documentation to determine how to enter this
information (many UNIX systems also have template examples in the bootptab
file that you can use for reference). Some examples of typical /etc/bootptab
entries include:
BRN_310107 1
00:80:77:31:01:07 192.189.207.3
and:
BRN_310107:ht=ethernet:ha=008077310107:\
ip=192.189.207.3:
Certain BOOTP host software implementations will not respond to BOOTP
requests if you have not included a download filename in the configuration file;
if this is the case, simply create a null file on the host and specify the name of
this file and its path in the configuration file.
As with rarp, the Print / Fax server will load its IP address from the BOOTP
server when the FAX/MFC is powered on.
1-8
CHAPTER 1 TCP/IP CONFIGURATION
Changing the IP Address settings with the
TELNET Console
You can also use the TELNET command to change the IP address.
Using TELNET is effective way, when you change the IP address. But a valid IP
address must already be programmed into the Print / Fax server.
If you are using the TELNET, you will be expected to enter the password of the
Print / Fax server. Press RETURN and enter the default password of "access" in
response to the "#" prompt (it will not echo).
You will be prompted for a user name. Enter anything in response to this prompt.
You will then get the Local> prompt. Type SET IP ADDRESS ipaddress, where
ipaddress is the desired IP address you wish to assign to the Print / Fax server
(check with your network manager for the IP address to use). For example:
Local> SET IP ADDRESS 192.189.207.3
You will now need to set the subnet mask by typing SET IP SUBNET subnet
mask, where subnet mask is the desired subnet mask you wish to assign to the
Print / Fax server (check with your network manager for the subnet mask to use).
For example:
Local> SET IP SUBNET 255.255.255.0
If you do not have any subnets, use one of the following default subnet masks:
255.255.255.0
255.255.0.0
255.0.0.0
for class C networks
for class B networks
for class A networks
The leftmost group of digits in your IP address can identify the type of network
you have. The value of this group ranges from 192 through 255 for Class C
networks (e.g., 192.189.207.3), 128 through 191 for Class B networks
(e.g.,128.10.1.30), and 1 through 127 for Class A networks (e.g., 13.27.7.1).
If you have a gateway (router), enter its address with the command SET IP
ROUTER routeraddress, where routeraddress is the desired IP address of the
gateway you wish to assign to the Print / Fax server. For example:
Local> SET IP ROUTER 192.189.207.1
To verify that you have entered the IP information correctly, type SHOW IP.
Type EXIT or CTR-D (i.e., hold down the control key and type "D") to end the
remote console session.
1-9
CHAPTER 2 FRONT PANEL SETUP MENU
CHAPTER TWO
21
2
Front Panel Setup Menu
LAN Main Setup Menu
The LAN menu selections allow you to setup the Brother FAX/MFC for your
network and Internet Fax configuration. Press [Menu] then press the appropriate
number for LAN, based on the selections displayed on your machine. After you
have displayed the LAN Main Setup menu, there are six main selections: 1Setup TCP/IP, 2-Setup Internet, 3-Setup Mail RX, 4-Setup Mail TX, 5-Setup
Relay and 6-Setup MISC. Proceed to the menu selection you wish to configure.
Please note that once you have specified a valid IP address for the machine, it is
also possible to configure many aspects of the FAX/MFC using your favorite
web browser. For added flexibility, the FAX/MFC is supplied with the BRAdmin
®
Professional Windows software, which also can be used to configure many
aspects of the NC-8100h.
1-Setup TCP/IP
This menu has eight sections: 1-Boot Method, 2-IP Address, 3-Subnet Mask, 4Gateway, 5-Host Name, 6-WINS Config, 7-WINS Server and 8-DNS Server.
1-BOOT METHOD
1.
2.
3.
4.
5.
6.
7.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [1] [1].
Press ! or " to select AUTO, STATIC, RARP, BOOTP or DHCP.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
Now make sure that you power cycle the FAX/MFC.
2-1
CHAPTER 2 FRONT PANEL SETUP MENU
STATIC mode
In this mode the FAX/MFC IP address must be manually assigned. Once entered
the IP address is locked to the assigned address.
AUTO mode
In this mode, the FAX/MFC will scan the network for a DHCP server, if it can
find one, and if the DHCP server is configured to allocate an IP address to the
FAX/MFC, then the IP address supplied by the DHCP server will used. If no
DHCP server is available, then the FAX/MFC will scan for a BOOTP server. If a
BOOTP server is available, and it is configured correctly, the FAX/MFC will
take its IP address from the BOOTP server. After it is initially powered ON, it
may take a few minutes for the FAX/MFC to scan the network for a server.
If your FAX/MFC supports “POWER SAVE mode” and you are using the
AUTO Boot mode, POWER SAVE must be set to OFF.
RARP mode
Brother Print / Fax server IP address can be configured using the Reverse ARP
(rarp) facility on your host computer. This is done by editing the /etc/ethers file
(if this file does not exist, you can create it) with an entry similar to the
following:
00:80:77:31:01:07
BRN_310107
Where the first entry is the Ethernet address of the Print / Fax server and the
second entry is the name of the Print / Fax server (the name must be the same as
the one you put in the /etc/hosts file).
If the rarp daemon is not already running, start it (depending on the system the
command can be rarpd, rarpd -a, in.rarpd -a or something else; type man rarpd or
refer to your system documentation for additional information). To verify that the
rarp daemon is running on a Berkeley UNIX-based system, type the following
command:
ps -ax | grep -v grep | grep rarpd
For AT&T UNIX-based systems, type:
ps -ef | grep -v grep | grep rarpd
The Brother Print / Fax server will get the IP address from the rarp daemon when
it is powered on.
BOOTP mode
BOOTP is an alternative to rarp that has the advantage of allowing configuration
of the subnet mask and gateway. In order to use BOOTP to configure the IP
address make sure that BOOTP is installed and running on your host computer (it
should appear in the /etc/services file on your host as a real service; type man
bootpd or refer to your system documentation for information). BOOTP is
usually started up via the /etc/inetd.conf file, so you may need to enable it by
removing the "#" in front of the bootp entry in that file. For example, a typical
bootp entry in the /etc/inetd.conf file would be:
#bootp dgram udp wait /usr/etc/bootpd bootpd -i
Depending on the system, this entry might be called "bootps" instead of "bootp".
2-2
CHAPTER 2 FRONT PANEL SETUP MENU
In order to enable BOOTP, simply use an editor to delete the "#" (if there is no
"#", then BOOTP is already enabled). Then edit the BOOTP configuration file
(usually /etc/bootptab) and enter the name, network type (1 for Ethernet),
Ethernet address and the IP address, subnet mask and gateway of the Print / Fax
server. Unfortunately, the exact format for doing this is not standardized, so you
will need to refer to your system documentation to determine how to enter this
information (many UNIX systems also have template examples in the bootptab
file that you can use for reference). Some examples of typical /etc/bootptab
entries include:
BRN_310107 1
00:80:77:31:01:07 192.189.207.3
and:
BRN_310107:ht=ethernet:ha=008077310107:\
ip=192.189.207.3:
Certain BOOTP host software implementations will not respond to BOOTP
requests if you have not included a download filename in the configuration file;
if this is the case, simply create a null file on the host and specify the name of
this file and its path in the configuration file.
As with rarp, the Print / Fax server will load its IP address from the BOOTP
server when the printer is powered on.
DHCP mode
Dynamic Host Configuration Protocol (DHCP) is one of several automated
mechanisms for IP address allocation. If you have DHCP Server in your network
®
®
(typically a Unix, Windows NT /2000 or Novell Netware network) the Print /
Fax server will automatically obtains its IP address from DHCP server and
register its name with any RFC 1001 and 1002-compliant dynamic name services.
If you do not want your Print / Fax server configured via DHCP, BOOTP or
RARP, you must set the BOOT METHOD to static, this will prevent the Print /
Fax server from trying to obtain an IP address from any of these systems. To
change the BOOT METHOD, use the print front panel (for those printers that
have a LCD panel, TELNET (using the SET IP METHOD command), Web
browser or by using the BRAdmin application.
2-IP ADDRESS
1.
2.
3.
4.
5.
6.
7.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [1] [2].
Select [1] to change the IP address—OR—[2] to exit.
Enter the IP address.
Press [Set] to accept the IP address.
Press [Stop/Exit] to exit the configuration menu.
2-3
CHAPTER 2 FRONT PANEL SETUP MENU
IP ADDRESS
This field displays the current IP address of the FAX/MFC. If you have selected
a Boot Method of STATIC, enter the IP address that you wish to assign to the
FAX/MFC (check with your network manager for the IP address to use). If you
have selected a method other than STATIC, the FAX/MFC will attempt to
determine its IP address using the DHCP or BOOTP protocols. The default IP
address of the Brother network board in your FAX/MFC will probably be
incompatible with the IP address numbering scheme of your network. We
recommend that you contact your network manager for an IP address for the
network the unit will be connected on.
When the BOOT METHOD is set to “AUTO”, the FAX/MFC cannot receive IP
®
address from a BOOTP server in Windows 2000. So please ensure that you use
®
DHCP for Windows 2000 server.
3-SUBNET MASK
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [1] [3].
Enter the Subnet Mask address.
Press [Set] to accept the IP address.
Press [Stop/Exit] to exit the configuration menu.
SUBNET Mask
This field displays the current subnet mask used by the FAX/MFC. If you are not
using DHCP or BOOTP to obtain the subnet mask, enter the desired subnet
mask. Check with your network manager for the subnet mask to use.
4-GATEWAY
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [1] [4].
Enter the Gateway address.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
GATEWAY
This field displays the current gateway or router address used by the FAX/MFC.
If you are not using DHCP or BOOTP to obtain the gateway or router address,
enter the address you wish to assign. If you do not have a gateway or router,
leave this field blank. Check with your network manager if you are unsure.
2-4
CHAPTER 2 FRONT PANEL SETUP MENU
5-HOST NAME
1.
2.
3.
4.
5.
6.
7.
Press the [Menu] button to display the configuration menu.
Select LAN
Press [1] [5].
Select [1] to change the Host Name—OR—[2] to exit.
Enter the Host Name.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
HOST NAME
You can register the machine name on the Network. This name is often referred
to as a NetBIOS name; it will be the name that is registered by the WINS server
on your network. Brother recommends the name BRN-XXXXXX (where
XXXXXX is the last six digits of the Ethernet address) (up to 15 characters).
6-WINS Configuration
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN
Press [1] [6].
Press ! or " to select AUTO or STATIC.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
WINS Configuration
This selection controls how the FAX/MFC obtains the IP address for the WINS
Server.
AUTO
Automatically uses a DHCP request to determine the IP addresses for the primary
and secondary WINS servers. You must set the Boot Method to Auto for this
feature to work.
STATIC
Uses a specified IP address for the primary and secondary WINS servers.
7-WINS SERVER
1.
2.
3.
4.
5.
6.
7.
8.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [1] [7].
Press ! or " to select the Primary or secondary WINS Server.
Press [Set] to accept the selection.
Enter the WINS Server address.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
2-5
CHAPTER 2 FRONT PANEL SETUP MENU
PRIMARY WINS Server IP Address
®
This field specifies the IP address of the primary WINS (Windows Internet
Naming Service) server. If set to a non-zero value, the machine will contact this
®
server to register its name with the Windows Internet Name Service.
SECONDARY WINS Server IP Address
This field specifies the IP address of the secondary WINS server. It is used as a
backup to the Primary WINS server address. If the Primary server is unavailable,
the FAX/MFC still can register itself with a secondary server. If set to a non-zero
®
value, the machine will contact this server to register its name with the Windows
Internet Name Service. If you have a primary WINS server, but no secondary
WINS server, simply leave this field blank.
8-DNS SERVER
1.
2.
3.
4.
5.
6.
7.
8.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [1] [8].
Press ! or " to select the Primary or secondary DNS Server.
Press [Set] to accept the selection.
Enter the DNS Server address.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
PRIMARY DNS Server IP Address
This field specifies the IP address of the primary DNS (Domain Name Service)
server.
SECONDARY DNS Server IP Address
This field specifies the IP address of the secondary DNS server. It is used as a
backup to the Primary DNS server address. If the Primary server is unavailable,
the FAX/MFC will contact the Secondary DNS server.
2-Setup Internet
This menu has five selections: 1- Mail Address, 2-SMTP Server, 3-POP3 Server,
4-Mailbox Name and 5-Mailbox PWD. You may find that it is more convenient
to use your favorite web browser to configure these settings.
1-MAIL ADDRESS
1. Press the [Menu] button to display the configuration menu.
2. Select LAN.
3. Press [2] [1].
2-6
CHAPTER 2 FRONT PANEL SETUP MENU
Refer to the following table (only for MFC-9700):
Key
1
2
3
4
5
6
7
8
9
Once
@
A
D
G
J
M
P
T
W
Twice
.
B
E
H
K
N
Q
U
X
Three times
/
C
F
I
L
O
R
V
Y
Four times
1
2
3
4
5
6
S
8
Z
If you want to enter a blank space, press " twice.
To change the mode between upper case and lower case for entering the e-mail /
I-Fax address press [!Shift] and [3].
Refer to the following table (for other models):
One Touch Dial Key Alphabet Conversion Table
01 - a
17 – q
05 – e
21 – u
09 – i
25 – y
13 – m
29 – space
02 - b
18 – r
06 – f
22 – v
10 – j
26 – z
14 – n
30 – [ special ]
03 - c
19 – s
07 – g
23 – w
11 – k
27 - .
15 – o
31 – [ symbols]
04 - d
20 - t
08 - h
24 - x
12 - l
28 - @
16 – p
32 – a<->A
Making corrections:
If you entered a letter incorrectly and want to change it, press ! to move the
cursor after the last correct letter. Then re-enter the correct text and/or digits. You
can also back up and type over incorrect letters.
Repeating letters:
If you need to enter a character assigned to the same key as the previous
character, press " to move the cursor to the right.
Special characters and symbols :
Press * for
(space) ! “ # $ % & ’ () * + , - . / € (€ is not available for US and
Canada users)
Press # for
:;<=>?@[]^_
Press ∅ for
É À È Ê Î Ç Ë Ö 0 (For US and Canada users)
Ä Ë Ö Ü À Ç È • 0 (For other users)
As you enter the E-mail address, it will appear character by character on
the LCD panel.
If you specify more than 16 characters, the LCD panel will scroll the
name to the left, character by character. You can enter up to 60
characters.
Please note that also you can connect to the FAX/MFC using a web
browser and specify the E-mail address information through Web Based
Management.
2-7
CHAPTER 2 FRONT PANEL SETUP MENU
4. Press [Set] to accept the selection.
5. Press [Stop/Exit] to exit the configuration menu.
2-SMTP SERVER
1.
2.
3.
4.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [2] [2].
Press ! or " to select IP ADDRESS or NAME to select the method of
the entering the SMTP SERVER Address.
5. Enter the SMTP SERVER Address.
6. Press [Set] to accept the selection.
7. Press [Stop/Exit] to exit the configuration menu.
SMTP SERVER Address
This field displays the Host Name or IP address of an SMTP mail server
(outgoing E-mail Server) on your network.
(Ex, mailhost.brothermail.net -or- 192.000.000.001)
3-POP3 SERVER
1.
2.
3.
4.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [2] [3].
Press ! or " to select IP ADDRESS or NAME to select the method of
the entering the POP3 Server Address.
5. Enter the POP3 Server Address.
6. Press [Set] to accept the selection.
7. Press [Stop/Exit] to exit the configuration menu.
POP3 SERVER address
This field displays the Host Name or IP address of the POP3 server ( incoming
E-mail server) used by the Brother FAX/MFC. This address is necessary for the
Internet Fax features to function correctly.
(Ex, mailhost.brothermail.net -or- 192.000.000.001)
4-MAILBOX NAME
1.
2.
3.
4.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [2] [4].
Enter the user account name assigned to the Brother FAX/MFC to login
to the POP3 Server.
5. Press [Set] to accept the selection.
6. Press [Stop/Exit] to exit the configuration menu.
2-8
CHAPTER 2 FRONT PANEL SETUP MENU
5-MAILBOX PWD
1.
2.
3.
4.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [2] [5].
Enter the user password assigned to the FAX/MFC to login to the POP3
Server. Please note that this password is case sensitive.
5. Press [Set] to accept the selection.
6. Press [Stop/Exit] to exit the configuration menu.
3-Setup Mail RX
This menu has Five selections 1-Auto Polling, 2-Poll Frequency, 3-Header, 4-Del
Error Mail and 5-Notification.
1-AUTO POLLING
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [3] [1].
Press ! or " to select ON or OFF.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
AUTO POLLING
When set to ON the FAX/MFC automatically will check the POP3 server for
new messages. “NO MAIL” will be displayed if there are no E-mail messages
when the POP3 server is polled.
2-POLL FREQUENCY
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [3] [2].
Enter the polling frequency.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
POLLING FREQUENCY
Sets the interval for checking for new messages on the POP3 server (default is
10min).
3-HEADER
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [3] [3].
Press ! or " to select SUBJECT+FROM+TO or ALL or NONE.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
2-9
CHAPTER 2 FRONT PANEL SETUP MENU
HEADER
This selection allows the contents of the mail header to be printed when the
received message is printed (Subject+From+To or All or NONE).
4-DEL ERROR MAIL
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [3] [4].
Press ! or " to select ON or OFF.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
DELETE ERROR MAIL
When set to ON, the FAX/MFC automatically deletes error mails that the
FAX/MFC can not receive from the POP server.
5-NOTIFICATION
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [3] [5].
Press ! or " to select ON or MDN or OFF
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
NOTIFICATION
Notification feature allows a receive notification message to be transmitted to
the sending station to indicate successful reception of the I-Fax.
“ON” send notification mail to all I-Fax machines only sends an e-mail to I-Fax
that supports the “MDN” specification.
4-Setup Mail TX
This menu has three selections 1-Sender Subject, 2-Size Limit and 3-Notification.
1-SENDER SUBJECT
1.
2.
3.
4.
5.
6.
7.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [4] [1].
Select [1] to change the Sender Subject—OR—[2] to exit.
Enter the subject information.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
SENDER SUBJECT
This field displays the subject that is attached to the Internet Fax data being sent
from the Brother FAX/MFC to a PC (default is “Internet FAX Job”).
2-10
CHAPTER 2 FRONT PANEL SETUP MENU
2-SIZE LIMIT
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [4] [2].
Press ! or " to select ON or OFF.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
SIZE LIMIT
Some E-mail servers do not allow you to send large E-mail documents. The
FAX/MFC may display “Out of Memory” when trying to send E-mail documents
(the System Administrator will often place a limit on the maximum E-mail size).
With this function enabled, the FAX/MFC will display “Memory Full” when
trying to send E-mail documents over 4Mbyte in size. The document will not be
sent and an error report will be printed. The document you are sending should be
separated into smaller documents that will be accepted by the mail server. (Ex. A
42 page document of the CCITT#1 test chart is approximately 1Mbyte in size).
3-NOTIFICATION
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [4] [3].
Press ! or " to select ON or OFF.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
Notification feature when switched to “ON” sends two fields of data in addition
to the image data which requests a notification from the receiving station for
successful reception. The receiving I-Fax station must support the “MDN”
standard in order to be able to understand the request and consequently submit a
notification message confirming successful receipt of the I-Fax.
2-11
CHAPTER 2 FRONT PANEL SETUP MENU
5-Setup Relay
This menu has three selections 1-RLY Broadcast, 2-Relay Domain and 3-Relay
Report. For details on Relay Broadcast refer to Chapter3, How to use the WebBased Management Utility or Chapter 4 Internet Fax.
1-RLY BROADCAST
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [5] [1].
Press ! or " to select ON or OFF.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
RELAY BROADCAST
This function allows the FAX/MFC to receive a document over the Internet, and
then relay it to other fax machines through conventional analog landlines.
2-RELAY DOMAIN
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [5] [2].
Press ! or " to select the Relay Domain (01 – 10).
Press [Set] to accept the selection.
Enter the Relay Domain name for the Domain that is being allowed to
request a Relay Broadcast.
7. Press [Set] to accept the selection.
8. Press [Stop/Exit] to exit the configuration menu.
RELAY DOMAIN
You can register the Domain Names (Max.10) that are allowed to request a Relay
Broadcast.
3-RELAY REPORT
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [5] [3].
Press ! or " to select ON or OFF.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
Relay Broadcast Report can be printed at the FAX/MFC used as the Relay
Station for all Relay Broadcasts. Also, when the FAX/MFC is used with the
Brother Network PC Fax software the FAX/MFC is acting as a Relay Station for
fax transmissions from the network so a Relay Report can also be printed for
confirmation of sent network faxes.
Its primary function is to print reports of Relay Broadcasts from external sources
through the FAX/MFC. Please note that this is not possible without the consent
of the Relaying Station as permission in the form of Relay Domain has to be
given to external parties.
2-12
CHAPTER 2 FRONT PANEL SETUP MENU
6-Setup Misc.
1-NETWARE
You can select to switch the NetWare feature “ON”, this allows you specify the
Frame Type is item 2.
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [6] [1].
Press ! or " to select ON or OFF.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
2-NET FRAME
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [6] [2].
4. Press ! or " to select AUTO/8023/ENET/8022/SNAP
Press [Set] accept the selection.
Press [Stop/Exit] to exit the configuration menu.
AUTO sets the Frame type to automatic, the network card will detect the frame
type being used by the NetWare server (Recommended).
802.3 sets the Frame type to Ethernet 802.3
ENET sets the Frame Type to Ethernet II
802.2 sets the Frame type to Ethernet 802.2
SNAP sets the Frame type to Ethernet SNAP
* NET Frame Setting is available when NetWare is “ON”
3-APPLETALK
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [6] [3].
Press ! or " to select ON or OFF.
Press [Set] accept the selection.
Press [Stop/Exit] to exit the configuration menu.
AppleTalk protocol is used with Macintosh Networks. If you are your FAX/MFC
on a Macintosh network please select to ON.
4-DLC/LLC
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [6] [4].
Press ! or " to select ON or OFF.
Press [Set] accept the selection.
Press [Stop/Exit] to exit the configuration menu.
2-13
CHAPTER 2 FRONT PANEL SETUP MENU
5-NETBIOS/IP
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [6] [5].
Press ! or " to select ON or OFF.
Press [Set] accept the selection.
Press [Stop/Exit] to exit the configuration menu.
The NC-8100h Print / Fax Server supports SMB (Server Message Block) over the
TCP/IP protocol via the NetBIOS interface. This means that just like regular
®
Windows PC’s the Brother FAX/MFC can appear in your network neighborhood.
The main advantage of NetBIOS printing is that you are able to print from legacy
DOS applications that are running on PC’s that are connected to Microsoft networks.
6-ETHERNET
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [6] [6].
Press ! or " to select AUTO/100B-FD/100B-HD/10B-FD/10B-HD
Press [Set] accept the selection.
Press [Stop/Exit] to exit the configuration menu.
Ethernet link mode. Auto allows the print server to operate in 100BaseTX full or
half duplex, or in 10BaseT half duplex mode by auto negotiation.
100BaseTX Full Duplex (100B-FD) or Half Duplex (100B-HD) and 10BaseT
Full Duplex (10B-FD) or Half Duplex (10B-HD) fix the print server link mode.
This change is valid after the print server has been reset. NOTE: if you
incorrectly set this value, you may not be able to communicate with your print
server.
7-TIME ZONE
1.
2.
3.
4.
5.
6.
Press the [Menu] button to display the configuration menu.
Select LAN.
Press [6] [7].
Press ! or " to set the time.
Press [Set] to accept the selection.
Press [Stop/Exit] to exit the configuration menu.
TIME ZONE
This field displays the time zone you can set for your country. The time is the
difference between your location and Greenwich Mean Time. This time will be
shown on documents received via the Internet. For example the Time Zone for
Eastern Time in the USA and Canada is GMT-05:00. You can determine the time
®
difference for you location by using the Time Zone setting in Windows .
®
Windows Time Zone Setting:
1.
2.
3.
4.
Click on Start.
Select Settings / Control Panel.
Double click on Date/Time.
Select Time Zone.
Verify your time zone setting from the pull-down menu (this menu displays the
time difference from GMT).
2-14
CHAPTER 2 FRONT PANEL SETUP MENU
User Setting List
1. Press the [Reports] button.
2. Select USER SETTINGS/SYSTEM SETUP.
3. Press [Set] to print the report.
This feature prints a report listing all the current user settings. The NC-8100h
Print / Fax Server Settings will be printed on the second page of the report.
2-15
CHAPTER 3 WEB BASED MANAGEMENT
CHAPTER THREE
31
3
Web Based Management
How to Use the Web-Based
Management Utility
Overview
The Web Based Management utility provides easy management and status
information for your Brother FAX/MFC.
A standard World Wide Web Browser (we recommend Netscape Navigator
version 4.xx /Microsoft Internet Explorer version 4.xx a or later) can be used to
manage your Brother FAX/MFC using the HTTP (Hyper-Text Transfer Protocol).
The following are the main features of the Web Based Management utility:
1. Machine status information.
2. Change Fax configuration items, such as Initial Setup, One Touch Dial
settings and Remote Fax.
3. You can also change network settings such as TCP/IP information,
Internet Fax address information, etc.
You must use the TCP/IP protocol on your network and have a valid IP address
programmed into the Brother FAX/MFC.
3-1
CHAPTER 3 WEB BASED MANAGEMENT
How to Connect Using a Browser
Type the IP address of the Brother FAX/MFC into your Web browser ( Ex.
http://192.189.207.3). You can also use the NetBIOS name (Host Name) of the
®
Brother network board if you are in Microsoft Windows domain/Workgroup
environment (WINS Config/WINS Server must already be set).
If your FAX/MFC supports English, French, German, Dutch, Italian or Spanish,
you must set the same language in your Web Browser. If your FAX/MFC does
not support these languages set your Web Browser for English.
Password Information
Important Information:
Login names are not
changeable. Login names
and passwords are both
case sensitive
Web Based Management offers two levels of password access. Users are able to
access to the General Setup, Fax settings, I-Fax Settings and Lists and Reports.
The default user name for Users is user and the default password is access
Administrators are able to access all settings. The login name for the
Administrator is admin and the default password is access.
3-2
CHAPTER 4 INTERNET FAX
CHAPTER FOUR
41
4
Internet FAX
Overview
Internet Faxing (I-FAX) allows you to send and receive FAX documents using
the Internet as the transport mechanism. Documents are transmitted in E-mail
messages as attached TIFF-F files. This means that PC’s are also able to receive
and send documents, providing that the PC has as an application that can
®
generate and view TIFF-F files, your can use Microsoft Imaging or A TIFF-F
viewer application [Pagis Viewer 2.0] is available as a download from the
Brother Web site (http://www.brother.com). Any documents sent via the
FAX/MFC will automatically be converted into a TIFF-F format. If you wish to
send and receive messages to and from your FAX/MFC, your mail application on
the PC must be able to support the MIME format.
4-1
CHAPTER 4 INTERNET FAX
Getting Connected
Before sending or receiving an Internet Fax you must configure your Brother
FAX/MFC to communicate with your network and mail server. You must ensure
the following: a correctly configured IP address for your FAX/MFC, an E-mail
address for your FAX/MFC, the mail server(s) IP address, mailbox name and
password for your Brother FAX/MFC. If you are unsure of any of these items,
please contact your systems administrator. For details of how to configure this
information, refer to the Web Based Management section (Internet Settings) of
this User’s Guide.
Front Panel Key Functions
Shift + [1]
Used to change input mode. You can use Dial Pad keys as Standard alphabet
character keys.
Dial Pad
Used to enter Standard Alpha characters (26 letters), as well as @ . space ! “ # %
& ‘ () + / : ; < > = ? [ ] ^ – $ , *, _ and Numbers.
Shift + [3]
To change between upper case and lower case for entering the e-mail / I-Fax
address.
! or "
Moves the LCD cursor to the left or right.
Set
Used to store multiple numbers.
Fax Start
Begins transmitting the document.
Stop/Exit
Deletes entered data and stops the scanning or transmitting process.
One Touch Dial / Speed Dial / Tel Index / Group Dial
These functions work the same way as with conventional FAX/MFC’s.
However, please note that you cannot use chain dialling for E-mail addresses.
Shift + Start
Used to receive E-mail from the POP3 server manually.
4-2
CHAPTER 4 INTERNET FAX
Sending an Internet Fax
•
Send the Internet Fax in the same way to send a fax.
If you have already programmed the addresses of the Internet Fax addresses into
the FAX/MFC as a One Touch or Speed Dial, you can send the Internet Fax in
the same way as you would send a normal fax.
You can select your preferred resolution by selecting the Fax Resolution key on
the panel before sending the Internet Fax. But you cannot send the color
document.
•
Send the Internet Fax with the Scan to E-mail button (only for the
models with the Scan to keys).
1. Set the document that you wish to send in the auto feeder of
the Brother FAX/MFC.
2. Press the Scan to E-mail button on the control panel of the
FAX/MFC. The display will then alternate between
- Connect to PC
- Connect to LAN
Select the number for your preferred connection and press the “Set” key. A
submenu appears on the LCD so you can select the resolution and the scan to
format. Use the arrows keys to scroll through the options.
1. B/W STD
(200x100dpi Black and White)
2. B/W FINE
(200x200dpi Black and White)
3. COLOR STD
(150x150dpi Color)
4. COLOR FINE
(300x300dpi Color)
5. COLOR S.FINE
(600x600dpi Color)
* Options 3-5 are only available for the color models. You cannot set the
resolution set by the Fax Resolution key. Step 1 and 2 are sent in TIFF-F format
and options 3-5 are sent in JPEG format.
Select the number for your preferred resolution and format and press the “Set”
key.
If you have already programmed this information into the FAX/MFC as a One
Touch
or Speed Dial, simply select the appropriate Dial location and press “Fax Start”.
To manually enter the address, continue to the following step.
4-3
CHAPTER 4 INTERNET FAX
Entering Text
Press [1], while holding down [!Shift] to change into the "alphabet" dialling
mode.
MFC-9700:
You can now use the Dial Pad to dial the E-mail address. Refer to the following
table: Most number keys have three or four letters printed above them. The keys
for 0, #, * don’t have printed letters because they are used for special characters.
By pressing the appropriate number key the correct number of times, you can
access the character you want.
Key
1
2
3
4
5
6
7
8
9
Once
@
A
D
G
J
M
P
T
W
Twice
.
B
E
H
K
N
Q
U
X
Three times
/
C
F
I
L
O
R
V
Y
Four times
1
2
3
4
5
6
S
8
Z
Other models:
You can now use the One-Touch Dial keys to dial the E-mail address. Refer to the
following table:
One Touch Dial Key Alphabet Conversion Table
01 - a
17 – q
05 – e
21 – u
09 – i
25 – y
13 – m
29 – space
02 - b
18 – r
06 – f
22 – v
10 – j
26 – z
14 – n
30 – [ special ]
03 - c
19 – s
07 – g
23 – w
11 – k
27 - .
15 – o
31 – [ symbols]
04 - d
20 - t
08 - h
24 - x
12 - l
28 - @
16 – p
32 – a<->A
If you want to enter a blank space, press " twice.
To change the mode between upper case and lower case for entering the e-mail /
I-Fax address press [!Shift] and [3].
If you specify more than 16 characters, the LCD panel will scroll the name to the
left character by character. You can enter up to 60 characters.
Making corrections:
If you entered a letter incorrectly and want to change it, press ! to move the
cursor after the last correct letter. Then re-enter the correct text and/or digits. You
can also back up and type over incorrect letters.
4-4
CHAPTER 4 INTERNET FAX
Repeating letters:
If you need to enter a character assigned to the same key as the previous
character, press " to move the cursor to the right.
Special characters and symbols:
Press * for
(space) ! “ # $ % & ’ () * + , - . / € (€ is not available for US and
Canada users)
Press # for
:;<=>?@[]^_
Press ∅ for
É À È Ê Î Ç Ë Ö 0 (For US and Canada users)
Ä Ë Ö Ü À Ç È • 0 (For other users)
As you enter the Internet Fax address, it will appear character by character on the
LCD panel.
If you specify more than 16 characters, the LCD panel will scroll the name to the
left character by character. You can enter up to 60 characters.
1. Press [Fax Start] to send the document.
After the document is scanned, it is transmitted to the Recipient Internet Fax
Machine automatically via your SMTP server. You can cancel the send operation
by pressing the [Stop] button during scanning. After the transmission is finished,
the machine will return to standby mode.
Some E-mail servers do not allow you to send large E-mail documents (the
System Administrator will often place a limit on the maximum E-mail size). You
can enable the Limit Size of the Sent Mail feature. The machine will display
“Memory Full” when trying to send E-mail documents over 1Mbyte in size. The
document will not be sent and an error report will be printed. The document you
are sending should be separated into smaller documents that will be accepted by
the mail server. You can turn on this feature through the Web Management utility
or the LAN function mode.
4-5
CHAPTER 4 INTERNET FAX
Receiving E-mail or Internet Fax
There are 2 ways you can receive E-mail messages:
•
•
•
POP3 receiving at regular intervals
POP3 receiving (manually initiated)
SMTP receiving
Using POP3 receiving the FAX/MFC machine must poll the E-mail server to
receive the print jobs. This polling can occur at set intervals (for example, you
can configure the FAX/MFC to poll the E-mail server at 10 minute intervals) or
you can manually poll the server by pressing the Shift + Start button.
If your FAX/MFC starts to receive E-mail print jobs, the LCD panel will reflect
this activity. For example, you will see "RECEIVING" on the LCD panel
followed by "xx MAIL(S)". If you press the Shift + Start buttons to manually
poll the E-mail server for E-mail print jobs and there are no mail documents
waiting to be printed, the FAX/MFC will display "NO MAIL" on the LCD panel
for two seconds.
If your machine is out of paper when receiving data, the received data will be
held in the FAX/MFC’s memory. This data will be printed automatically after
paper is re-inserted into the machine. Memory receive must be switched “ON”.
If the received mail is not in a plain text format or an attached file is not in the
TIFF-F format, the following error message will be printed: “ATTACHED FILE
FORMAT NOT SUPPORTED. FILE NAME:XXXXXX.doc” If the received
mail is too large, the following error message will be printed: “E-MAIL FILE
TOO LARGE.” If “Delete POP Receive Error Mail” is “ON” (default) then error
mail is automatically deleted from the E-mail Server.
4-6
CHAPTER 4 INTERNET FAX
Receiving an Internet Fax to a PC
When a PC receives an Internet Fax document, the document is attached to
a mail message that informs the PC that it is receiving a document from an
Internet Fax. This is notified in the Subject field of the received mail
message.
®
If the PC to which you wish to send a document is not running Windows 95/
®
®
98/98SE/Me or Windows NT 4.0/2000/XP operating system, please inform the
PC’s owner that software must be downloaded for documents in the TIFF-F
format to be viewed.
You can download a TIFF-F viewer from the Brother Web site
®
(http://solutions.brother.com). You can also use “ Microsoft Imaging” that
®
®
®
is supplied with Windows 95/98/Me or Windows NT 4.0/2000/XP but some
®
older versions of Windows 95 do not support viewing TIFF-F documents.
Forwarding Received E-mail and Fax
Messages
You can forward received E-mail or standard fax messages to another E-mail
address or fax machine. Received messages can be forwarded via E-mail to a PC
or Internet Fax. They can also be forwarded via standard phone lines to another
FAX/MFC.
Please see your FAX/MFC User guide to check that this feature is supported.
This function is only for monochrome models.
This can be done using the Web Management Utility or through the front panel.
The steps for configuring Fax Forward can be found in the User Guide supplied
with your FAX/MFC.
4-7
CHAPTER 4 INTERNET FAX
Relay Broadcasting
This function allows the Brother FAX/MFC to receive a document over the
Internet, and then relay it to other fax machines through conventional telephone
lines.
If you wish to use your FAX/MFC as a relay broadcast device, you must specify
the domain name that you trust at the FAX/MFC, in other words, the portion of
the domain after the ‘@’ sign.
A trusted domain refers to the E-mail address. For example, if your address is
bob@brother.com , then we identify the domain as brother.com. If your E-mail
address is jack@brother.co.uk, then we identify the domain as brother.co.uk.
Use care in selecting a trusted domain since any user on a trusted domain will be
able to send a Relay Broadcast.
Relay Broadcast can support the relay of a document up to a maximum of 48 Fax
machines through conventional telephone lines.
This function is only for monochrome models.
4-8
CHAPTER 4 INTERNET FAX
Relay Broadcast from a FAX/MFC
FAX@brother.com
UKFAX@brother.co.uk
123456789
Your FAX/MFC has an E-mail address of FAX@brother.com, you wish to send
a document from this machine to another FAX/MFC in England with an E-mail
address of UKFAX@brother.co.uk, this machine will then forward the document
to a standard FAX machine using a conventional telephone line. If your E-mail
address is FAX@brother.com, you must configure a trusted domain name of
brother.com on the machine in England that will broadcast the document to the
conventional FAX machine. If you do not enter the domain name information,
then the machine in the middle (the machine that will broadcast the document)
will not trust any internet jobs that it receives from the FAX/MFC machine in the
@brother.com domain.
After the trusted domain is set you can send the document from your FAX/MFC
[I.E. FAX@brother.com] by entering the E-mail address of the FAX/MFC
[I.E. UKFAX@brother.co.uk] that will forward the document followed by the
phone number of the fax that will receive the document. The following is an
example of how to enter the E-mail address and phone number.
UKFAX@brother.co.uk(fax#123456789)
E-mail address
Fax Phone Number
The word “fax#” must be
included with the phone
number inside the parenthesis.
Sending to multiple phone numbers:
If you want to have the document relayed to more than one standard Fax machine
the address can be entered using the following method:
1. Enter the phone number of the first Fax machine
UKFAX@brother.co.uk(Fax#123).
2. Press the “Set” key.
3. Enter the phone number of the second Fax machine
UKFAX@brother.co.uk(Fax#456).
4. Press the “Start” key.
4-9
CHAPTER 4 INTERNET FAX
You can also store the address information in One-Touch Dial. For example:
Store UKFAX@brother.co.uk(Fax#123) in One-Touch Dial key 01 and store
UKFAX@brother.co.uk(Fax#456) in One-Touch Dial key 02. You can then
press the One-Touch Dial Key for each number instead on entering each
individual number.
Relay Broadcast from a PC
Your PC
UKFAX@brother.co.uk
123456789
You can also send E-mail from your PC and have it relayed to a conventional
FAX machine. The method of entering the phone number of the conventional
FAX machine that will receive the relayed E-mail will vary depending on the
mail application you are using. The following are some examples of different
mail applications:
Some E-mail applications do not support sending to multiple phone numbers. If
your E-mail application cannot support multiple phone numbers you will only be
able to relay to one Fax machine at a time.
Outlook Express / Internet Explorer 4 & 5/ Netscape Communicator 4.5/
Eudora Ver 4.x and Pegasus (for Europe):
Enter the address of the relay FAX/MFC and phone number of the FAX in the
“TO” box using the same method used when sending from an FAX/MFC.
UKFAX@brother.co.uk(fax#123456789)
Outlook 97/98/2000:
For Outlook 97/98 & 2000 the address information must be entered into the
address book as follows:
Name: fax#123456789
E-mail Address: UKFAX@brother.co.uk
4-10
CHAPTER 4 INTERNET FAX
TX Verification Mail
Transmission Verification Mail supports two separate functions. Verification
Mail for sending allows you request notification from the receiving station that
the I-Fax or E-mail was received and processed. Verification Mail for receiving
allows you to transmit a default report back to the sending station after
successfully receiving and processing an I-Fax or E-mail.
To use this feature you must set the “Notification” option within the “Setup Mail
RX” and “Setup Mail TX” options.
Setup Mail (TX)
You can set the “Notification” option in the “Setup Mail TX” option to either ON
or OFF. When switched to ON an additional field of information is sent with the
image data. This field is named “MDN”.
MDN
Mail Disposition Notification – This field requests the status of the I-Fax / E-mail
message after delivery through the SMTP (send mail transfer protocol) transport
system. Once the message has arrived at the Receiving station this data is used
when the FAX/MFC or user reads or prints the received I-Fax or E-mail. For
example, if the message is opened for reading or is printed the receiving station
sends back a notification to the original sending machine or user.
The receiving station must support the MDN field in order to be able to send a
notification report, otherwise the request will be ignored.
Setup Mail (RX)
There are three possible settings for this option ON/MDN/OFF.
Receive Notification “ON”
When switched to “ON” a fixed message is sent back to the sending station to
indicate successful reception and processing of the message. These fixed
messages depend on the operation requested by the sending station.
Report messages consist of
SUCCESS: ……………………..
or
FAILURE: ………………………
4-11
CHAPTER 4 INTERNET FAX
Receive Notification “MDN”
When switched to “MDN” a report as described above is sent back to the sending
station if the originating station sent the “MDN” field to request confirmation.
Receive Notification “OFF”
OFF – Switches all forms of receive notification OFF, no messages are send back
to the sending station regardless of the request.
Error mail
If there is a mail delivery error while sending an Internet Fax, the mail server will
send an error message back to the FAX/MFC and the error message will be
printed. If there is an error while receiving mail, an error message will be printed
(Example: “The message being sent to the FAX/MFC was not in a TIFF-F
format.”).
Important information on Internet Fax
Internet Fax Communication on a LAN system is basically the same as
communication via E-mail; however, it is different from Fax communication
using standard phone lines. The following is important information for using
Internet Fax:
•
•
•
•
•
Factors such as the receiver’s location, structure of the LAN system, and
how busy the circuit (such as the internet) is, may cause the system to take a
long time to send back an error mail. (normally 20 sec to 30 sec).
In the case of transmission through the Internet, due to its low level of
security, we recommend that you use standard phone lines to send
confidential documents.
If the receiver’s mail system is not compatible with the MIME format, you
cannot transmit a document to the receiver. Depending on receiver’s server,
there may be some cases in which the error mail will not be sent back.
If the size of a document’s image data is huge, there is a possibility of
unsuccessful transmission.
You cannot change font and character size of Internet mail that you received.
4-12
CHAPTER 4 INTERNET FAX
Using Scan to E-mail
When a PC receives an Internet Fax document, the document is attached to
a mail message that informs the PC that it is receiving a document from an
Internet Fax. This is notified in the Subject field of the received mail
message.
®
If the PC to which you wish to send a document is not running Windows 95/
®
®
98/98SE/Me or Windows NT 4.0/2000/XP operating system, please inform the
PC’s owner that software must be downloaded for documents in the TIFF-F
format to be viewed.
You can download a TIFF-F viewer from the Brother Web site
®
(http://solutions.brother.com). You can also use “ Microsoft Imaging” that
®
®
®
is supplied with Windows 95/98/Me or Windows NT 4.0/2000/XP but some
®
older versions of Windows 95 do not support viewing TIFF-F documents.
Before attempting to Scan to Email, it is necessary to set the network and the
mail server of the Brother FAX/MFC.
Set the appropriate IP address
Have a mail address
Have a mail server address
Have a mail box (mail ID) and a password
Please confirm if you set these correctly. If you do not know how to set, please
ask to the administrator.
See Chapter 2 Front Panel Setup Menu and Chapter 3 Web Based Management.
•
Send the Internet Fax in the same way to send a fax.
If you have already programmed the addresses of the Internet Fax receivers into
the FAX/MFC as a One Touch or Speed Dial, you can send the Internet Fax in
the same way as a usual way.
You can select the number for your preferred resolution by selecting the Fax
Resolution key on the panel. But you cannot send the color document.
•
Send the Internet Fax with the Scan to E-mail button (only for the
Scanner function models).
1. Set the document that you wish to send in the auto feeder of
the Brother FAX/MFC.
2. Press the Scan to E-mail button on the control panel of the
FAX/MFC. The display with alternate between
- Connect to PC
- Connect to LAN
Select the number for your preferred connection and press the “Set” key. A
submenu appears on the LCD so you can select the resolution and the scan to
format. Use the arrows keys to scroll through the options.
1. B/W STD
(200x100dpi Black and White)
2. B/W FINE
(200x200dpi Black and White)
3. COLOR STD
(150x150dpi Color)
4. COLOR FINE
(300x300dpi Color)
5. COLOR S.FINE
(600x600dpi Color)
* Step 3-5 are only for the color models. You cannot set the fax resolution set by
the Fax Resolution key. Step 1 and 2 are sent in TIFF format and step 3-5 are
sent in JPEG format.
4-13
CHAPTER 4 INTERNET FAX
Select the number for your preferred resolution and format and press the “Set”
key.
If you have already programmed this information into the FAX/MFC as a One
Touch
or Speed Dial, simply select the appropriate Dial location and press “Fax Start”.
To manually enter the address, continue to the following step.
Entering Text
Press [1], while holding down [!Shift] to change into the "alphabet" dialling
mode.
MFC-9700:
You can now use the Dial Pad to dial the E-mail address. Refer to the following
table: Most number keys have three or four letters printed above them. The keys
for 0, #, * don’t have printed letters because they are used for special characters.
By pressing the appropriate number key the correct number of times, you can
access the character you want.
Key
1
2
3
4
5
6
7
8
9
Once
@
A
D
G
J
M
P
T
W
Twice
.
B
E
H
K
N
Q
U
X
Three times
/
C
F
I
L
O
R
V
Y
Four times
1
2
3
4
5
6
S
8
Z
Other models:
You can now use the One-Touch Dial keys to dial the E-mail address. Refer to the
following table:
One Touch Dial Key Alphabet Conversion Table
01 - a
02 - b
03 - c
17 – q
18 – r
19 – s
05 – e
06 – f
07 – g
21 – u
22 – v
23 – w
09 – i
10 – j
11 – k
25 – y
26 – z
27 - .
13 – m
14 – n
15 – o
29 – space
30 – [ special ]
31 – [ symbols]
If you want to enter a blank space, press " twice.
04 - d
20 - t
08 - h
24 - x
12 - l
28 - @
16 – p
32 – a<->A
To change the mode between upper case and lower case for entering the e-mail /
I-Fax address press [!Shift] and [3].
If you specify more than 16 characters, the LCD panel will scroll the name to the
left character by character. You can enter up to 60 characters.
4-14
CHAPTER 4 INTERNET FAX
Making corrections:
If you entered a letter incorrectly and want to change it, press ! to move the
cursor after the last correct letter. Then re-enter the correct text and/or digits. You
can also back up and type over incorrect letters.
Repeating letters:
If you need to enter a character assigned to the same key as the previous
character, press " to move the cursor to the right.
Special characters and symbols :
Press * for
(space) ! “ # $ % & ’ () * + , - . / € (€ is not available for US and
Canada users)
Press # for
:;<=>?@[]^_
Press ∅ for
É À È Ê Î Ç Ë Ö 0 (For US and Canada users)
Ä Ë Ö Ü À Ç È • 0 (For other users)
As you enter the Internet Fax address, it will appear character by character on the
LCD panel.
If you specify more than 16 characters, the LCD panel will scroll the name to the
left character by character. You can enter up to 60 characters.
5. Press [Fax Start] to send the document.
After the document is scanned, it is transmitted to the Recipient Internet Fax
Machine automatically via your SMTP server. You can cancel the send operation
by pressing the [Stop] button during scanning. After the transmission is finished,
the machine will return to standby mode.
Some E-mail servers do not allow you to send large E-mail documents (the
System Administrator will often place a limit on the maximum E-mail size). You
can enable the Limit Size of the Sent Mail feature. The machine will display
“Memory Full” when trying to send E-mail documents over 1Mbyte in size. The
document will not be sent and an error report will be printed. The document you
are sending should be separated into smaller documents that will be accepted by
the mail server. You can turn on this feature through the Web Management utility
or the LAN function mode.
4-15
CHAPTER 5 TCP/IP PRINTING
CHAPTER FIVE
51
5
TCP/IP Printing
®
Printing from Windows NT,
®
®
Windows 2000 or Windows
XP LAN Server and Warp
Server
Overview
®
Users of Windows NT can print directly to a network ready Brother FAX/MFC
®
using the TCP/IP protocol. Microsoft Windows NT 3.5x and NT 4.0 users must
®
®
install Microsoft's "TCP/IP printing" protocol. Windows 2000 and Windows
XP users are able to send print jobs directly to the printer without installing any
additional software.
Quick Tips:
1. The default IP address of Brother Print / Fax servers is 192.0.0.192. To
change it, use the FAX/MFC’s front panel, the BRAdmin application, or
let your DHCP server allocate an IP address.
2. The default password for Brother Print / Fax servers is "access".
®
®
3. Windows NT 3.51 and Windows NT 4.0 users must install the
"Microsoft TCP/IP printing" protocol (available through the control
panel applet)
®
®
4. Windows 2000 and Windows XP users can print using TCP/IP using
the standard Network Printing software and IPP protocol software built
®
®
into any Windows 2000 and Windows XP installation.
®
5. Windows 95/98/Me users can send print jobs using the IPP protocol via
®
®
a Windows 2000 or Windows XP computer providing that the
Microsoft Internet Print Services software is installed on the client PC,
®
®
IIS is installed and running on the Windows 2000 or Windows XP
computer and that the client PC is using version 4 or later of Microsoft
Internet Explorer.
6. The default name for a Brother Print / Fax server is usually
BRN_xxxxxx (where xxxxxx is the last six digits of the Ethernet address
of the Print / Fax server).
5-1
CHAPTER 5 TCP/IP PRINTING
Windows® NT 3.5x/NT 4.0/2000/XP
(TCP/IP) Configuration
®
If you have not already done so, install the TCP/IP protocol onto your Windows
NT system. This is done via the Network icon in the Control Panel window of the
®
Windows NT system (the Control Panel is in the Main window on NT 3.5x
systems, or use the Start button on NT 4.0 to access the Settings/Control Panel
®
®
menu). The default configuration of Windows 2000 and Windows XP
automatically installs the TCP/IP protocol. Refer to the appropriate section in this
chapter for more information.
5-2
CHAPTER 5 TCP/IP PRINTING
Windows® 2000 Windows® XP Printing
(Printer Driver not yet installed)
®
®
By default, Windows 2000 and Windows XP systems install with all the
necessary software required for you to be able to print. This chapter describes the
two most commonly used configurations, Standard TCP/IP Port printing and IPP
(Internet Printing Protocol). If you have already installed the printer driver, jump
to the printer driver already installed section.
Standard TCP/IP Port Printing
1. From the Printers Folder select "Add Printer", the "Add Printer Wizard"
will now start. Click on "Next".
2. Now select the Local Printer option and deselect the "Automatically
detect and install my Plug and Play printer" option.
3. Click on "Next".
4. You must now select the correct Network printing port.
®
a. For Windows 2000: Select the "Standard TCP/IP Port" option
as the port.
®
b. For Windows XP: Select a new port from the pull-down
window and select “Standard TCP/IP Port”.
5. When you have done that click "Next".
6. The "Add Standard TCP/IP Port Wizard" will now appear. Click the
"Next" button.
7. Enter the IP address, or name of the printer you wish to configure. The
Wizard will automatically enter the Port name information for you.
8. Click the "Next" button.
®
9. Windows will now contact the printer that you specified. If you did not
specify the correct IP address or name then you will receive an error
message.
10. Click the "Finish" button to complete the Wizard.
11. Now that you have configured the port, you must specify which printer
driver you wish to use. Select the appropriate driver from the list of
supported printers. If you are using a driver supplied on CD-ROM
supplied with your FAX/MFC then select the "Have Disk" option to
®
browse to the CD-ROM disk. You can also click the “Windows
Update” button to connect directly to Microsoft’s support Web site to
download printer drivers.
12. When the driver is installed, click the Next button.
13. Specify a name and click the “Next” button.
14. Now specify if you wish to share the printer, enter the share name and
click “Next”.
15. Continue through the Wizard clicking the “Finish” button when
complete.
5-3
CHAPTER 5 TCP/IP PRINTING
IPP Printing from Windows® 2000 and
Windows® XP Clients
If you wish to print using the IPP protocol, follow these steps:
1. From the Printers Folder select "Add Printer", the "Add Printer Wizard"
will now stat. Click on "Next"
2. Select "Network Printer"
®
3. For Windows 2000: Click the "Connect to a printer on the Internet or
on your intranet" option
®
For Windows XP: Click the “Connect to a printer on the Internet or on
a home or office network” option.
4. You must now enter a URL name, a typical example of a URL name for
a printer that supports the IPP protocol is: http://ip_address:631/ipp
(where ip_address is the IP address, NetBIOS name or DNS name of the
Print / Fax server).
5. Click the "Next" button
®
6. Windows 2000 will now connect to the device that you specified and
determine the model number of the printer, if the appropriate driver is
installed on the PC, it will be used, if the appropriate driver is not
available you will be asked to insert the driver diskette that was supplied
with the printer.
7. Follow the Wizard through to the end of the installation.
8. Click the "Finish" button to complete the Wizard.
®
IPP printing from Windows 95/98/Me Clients
It is also possible to send a IPP print jobs from a Windows 95/98/Me client PC
®
providing the PC has the ability to connect to and access Windows 2000 or
®
Windows XP resources. Visit the Microsoft web site (www.microsoft.com) and
®
®
download the Windows Internet Print Services support software for Windows
systems.
®
Once installed, this software will allow you to connect to a Windows 2000 or
®
Windows XP system that is also running IIS and send print jobs using the IPP
protocol.
®
By using Microsoft’s IPP software you can also send jobs to other printers that
do not support the IPP protocol.
Windows® 2000 Windows® XP Printing
(Printer Driver already installed)
If you have already installed the printer driver and wish to configure it for
network printing, follow these steps:
1.
2.
3.
4.
Select the printer driver you wish to configure
Select File and then chose Properties
Click the Ports tab of the driver and click “Add Port”
Select the port that you wish to use, typically this would be “Standard
TCP/IP Port”, then click the “New Port…” button.
5. The standard TCP/IP Port Wizard will start. Follow steps 6-10 of the
“Standard TCP/IP Port Printing” section.
5-4
CHAPTER 5 TCP/IP PRINTING
Windows® NT 4.0 Printing
If you did not install the TCP/IP protocol or the Microsoft TCP/IP Printing
®
protocol during the installation of your Windows NT 4.0 system (either
workstation or server) follow these steps. Please note that it is essential that you
install the Microsoft TCP/IP Printing protocol if you wish to print over the
network using the TCP/IP protocol. If you have already installed the TCP/IP
protocol and Printing protocol proceed to step 2.
Step 1: Running the Network applet, click on the Protocols tab.
1. Select Add, and double click on TCP/IP protocol.
2. Insert the requested disk(s), or CD-ROM, to copy the required files.
3. Click on the Services tab, click on Add and double click on Microsoft
TCP/IP Printing.
4. Again insert the requested disk (s) or CD-ROM.
5. Click on the Protocols tab when then copying is finished.
6. Double click on the TCP/IP Protocol option and add the host IP address,
subnet mask, and gateway address. Consult your system manager for
these addresses.
7. Click OK twice to exit (your NT server will need to be re-booted).
5-5
CHAPTER 5 TCP/IP PRINTING
Windows® NT 4.0 Printing
(Printer Driver not yet installed)
1. Go to the Start button, choose Settings, and then select Printers. Double
click the Add Printer icon to get the Add Printer Wizard. Select My
Computer (Not Network Printer) and click on Next.
2. Select Add Port, select LPR Port (LPR Port will not be displayed unless
you install the "Microsoft TCP/IP Printing" protocol as described earlier)
from the list of available ports and click on New Port.
3. Type in the IP address that you wish to assign to the Print / Fax server in
the Name or address of server providing lpd: box. If you have edited
your HOSTS file are using Domain Name System, enter the name
associated with the Print / Fax server, instead of an IP address. As the
Print / Fax server supports TCP/IP and NetBIOS names, you can also
enter the NetBIOS name of the Print / Fax server. The NetBIOS name
can be seen in your print configuration sheet. From default the NetBIOS
name will usually appear as "BRN_xxxxxx" where xxxxxx is the last six
digits of the Ethernet address.
4. Type in the Print / Fax server service name in the Name of printer or
print queue on that server: box. If you do not know which service name
to use, enter BINARY_P1 and then click on OK:
Note
Refer to How to configure TCP/IP printing for UNIX system for more
information on Service Names.
5. Click on Close. The new Print / Fax server IP address should be listed
and highlighted as an available port. Click on Next.
6. Select the desired printer model. If the correct model is not displayed,
click on the "Have Disk" option and insert the CD-ROM supplied with
your FAX/MFC.
7. If the driver already exists, select Keep Existing Driver (if it does not,
this step will be skipped), and then click on Next.
8. If desired, change the name of the printer then click on Next.
9. If desired, make the printer shared (so other users can access it), and
select the operating system(s) that these other computers will be running.
Click on Next.
10. Select Yes when you are asked "Would you like to print a test page?"
Click on Finish to complete the installation. You may now print to the
printer as if it were a local printer.
5-6
CHAPTER 5 TCP/IP PRINTING
Windows® NT 4.0 Printing
(Printer Driver already installed)
Follow these steps if the printer driver is already installed.
1. Click on Start then select Settings/Printers to display the currently
installed printer drivers.
2. Double click the printer driver you wish to configure and select Printer
menu and then choose Properties.
3. Select the Ports tab and click on Add Port.
4. Select LPR Port (LPR Port will not be displayed unless you install the
"Microsoft TCP/IP Printing" protocol as described earlier) from the list
of available ports and click on New Port.
5. Type in the IP address that you assigned to the Print / Fax server in the
Name or address of server providing lpd: box. If you have edited your
HOSTS file or are using Domain Name System, you can enter the name
associated with the Print / Fax server, instead of an IP address. As the
Print / Fax server supports TCP/IP and NetBIOS names, you can also
enter the NetBIOS name of the Print / Fax server. The NetBIOS name
can be seen in your print configuration sheet. From default the NetBIOS
name will usually appear as "BRN_xxxxxx" where xxxxxx is the last six
digits of the Ethernet address.
6. Type in the Print / Fax server service name in the Name of printer or
print queue on that server: box. If you do not know which service name
to use, enter BINARY_P1 and then click on OK:
Figure 1 Add LPR compatible printer screen
7. Click on the Close button.
8. You should now see that the printer driver is configured to print to the IP
address (or name) that you specified.
9. If you wish to share the printer, click on the Share tab and share the
driver.
5-7
CHAPTER 5 TCP/IP PRINTING
Windows® NT 3.5x Printing
1. Go into the Control Panel and run the Network applet.
2. Select Add Software and TCP/IP Protocol and related components.
3. Select the TCP/IP Network Printing Support check box. And then click
on the Continue button. (This option will be unavailable if the TCP/IP
Network Printing Support protocol is already installed.
4. Insert the requested disk(s) to copy the required files. Your NT server
will need to be re-booted when the files are copied over.
Windows® NT 3.5x Printing
(Printer Driver not yet installed)
®
If you have Windows NT 3.5 or 3.51, use the following procedure to configure
the Print / Fax server.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Go to the Main window and select the Print Manager icon.
Select Printer menu.
Select Create Printer.
Enter any name for the Printer Name.
Select Driver. Choose the appropriate driver.
Select Description. Enter anything for the description.
Select Print to and then select Other.
Select LPR Port.
Type in the IP address that you assigned to the Print / Fax server in the
Name or address of host server providing lpd: box. If you have edited
your HOSTS file or are using Domain Name System, enter the name
associated with the Print / Fax server, instead of an IP address.
10. Type in the Print / Fax server service name in the Name of printer on
that Machine. If you do not know which service name to use, enter
BINARY_P1 and then click on OK.
Note
Refer to How to configure TCP/IP printing for Unix system for more information
on Service Names.
Share the printer if necessary.
5-8
CHAPTER 5 TCP/IP PRINTING
Other Sources of Information
1. Visit http://solutions.brother.com/ for more information on network
printing and for documents on the IPP protocol and how to configure a
®
Windows 2000/95/98/Me System.
2. Refer to chapter 1 of this user guide to learn how to configure the IP
address of the printer.
5-9
CHAPTER 6 TCP/IP PEER TO PEER PRINTING
CHAPTER SIX
61
6
Peer to Peer Printing
®
How to Print in a Windows
95/98/Me Peer to Peer network
Overview
®
Microsoft's Windows 95/98/Me operating systems features built-in networking
®
capabilities. These capabilities allow a Windows PC to be configured as a client
workstation in a file server based network environment.
®
For smaller networks, Windows 95/98/Me also allows the PC to operate in a
peer-to-peer mode. In this mode, the PC can share resources with other PCs on
the network without the need for a central file server.
Quick Tips:
1. The default IP address of Brother Print / Fax servers is 192.0.0.192. To
change it, use the FAX/MFC’s front panel , the BRAdmin application, or
let your DHCP server allocate an IP address to the printer.
2. Refer to chapter 1 of this user guide to learn how to configure the IP
address on your FAX/MFC.
3. The default password for Brother Print / Fax servers is "access".
®
4. Windows 95/98/Me users can send print jobs using the IPP protocol via
®
®
a Windows 2000 or Windows XP computer providing that the
Microsoft Internet Print Services software is installed on the client PC,
®
®
IIS is installed and running on the Windows 2000 or Windows XP and
that the client PC is using version 4 or later of Microsoft Internet
Explorer.
5. Brother printers are also compatible with HP JetDirect software, this
means that you can use HP utilities to manage and to print to your
Brother printer.
6-1
CHAPTER 6 TCP/IP PEER TO PEER PRINTING
TCP/IP Printing
Our Peer to Peer printing software requires the TCP/IP protocol to be installed on
®
your Windows peer-to-peer computers and an IP Address has to be defined for
®
the Print / Fax server. Refer to your Windows documentation for more
®
information on how to configure the TCP/IP protocol on your Windows PC.
If you haven’t already done so, configure the IP address of the FAX/MFC, for
more information on IP address configuration, refer to chapter 1of this user guide.
6-2
CHAPTER 6 TCP/IP PEER TO PEER PRINTING
Installing the Brother Peer to Peer Software
1. Start the CD-ROM (supplied with your FAX/MFC) installation menu
program according to the Quick Setup Guide and select Install Software.
2. From the Network Applications menu select Install Software.
3. Click “Install” Network Print Software.
4. Push the Next button in response to the Welcome message.
5. Select the Brother Peer to Peer Print (LPR) button
6. Select the desired directory to install the Brother Network Direct Print
files and push Next. The installation program will create the directory
for you if it does not already exist on your disk.
7. Enter the Port name that you wish to use and click OK. The default port
name is BLP1. Whichever name you choose, it must be unique and it
MUST begin with BLP.
8. You must now enter the actual IP address of the Print / Fax server in the
"Printer name or IP address" field. If you have edited the hosts file on
your computer or are using Domain Name System, you can also enter
the name of the Print / Fax server. As the Print / Fax server supports
TCP/IP and NetBIOS names, you can also enter the NetBIOS name of
the Print / Fax server. The NetBIOS name can be seen in your print
configuration sheet. From default the NetBIOS name will usually appear
as "BRN_xxxxxx" where xxxxxx is the last six digits of the Ethernet
address.
®
Window 95/98/Me store the hosts file in the default Windows directory.
®
By default, the Windows hosts file is called hosts.sam. If you wish to use the
hosts file you must rename the file to hosts with no extension, the .sam extension
stands for sample.
9. Click the OK button. When prompted you must re-boot your computer.
6-3
CHAPTER 6 TCP/IP PEER TO PEER PRINTING
Associating to the printer
®
You must now create a printer on your Windows system using the standard
®
Windows printer setup procedure.
1.
2.
3.
4.
5.
6.
7.
8.
9.
To do this, go the Start button, select Setting and then Printers.
Select Add Printer to begin the printer installation.
Click Next when you get the add Printer Wizard window.
Select Local Printer when you are asked how the printers are connected
to your computer, and then push Next.
Select the correct driver. Click Next when you are done.
If you have selected a printer driver that is already being used, you have
the option of either keeping the existing driver (recommended) or
replacing it. Select the desired option and press Next.
Select the Brother LPR port (port name you assigned in step 4 of the
Installing the Brother Peer to Peer Print (LPR) Software section) and
press Next.
Enter any desired name for the Brother printer and press Next. For
example, you could call the printer "Networked Brother Printer".
®
Windows will now ask you if you wish to print out a test page, select
Yes and then select Finish.
You have now finished installing the Brother Network Direct Print software.
Adding a Second Brother LPR Port
You do not re-run the install program to add a new Brother LPR port. Instead,
®
press the Start button, select Settings, and open the Printers Windows . Click on
the icon of the printer that you wish to configure, select File form the Menu bar,
and then choose Properties. Click on the Details tab and push the Add Port button.
In the Add Port dialog, select the Other radio button and then highlight "Brother
LPR port". Click OK and enter the port name. The default port name is BLP1. If
you have already used this name, you will get an error message if you try to use it
again, in which case use BLP2, etc… Once you have specified the Port name,
click the OK button. You will then see the Port Properties Dialog.
Enter the IP address of the printer that you wish to print to and click OK. You
should now see the port that you have just created in the "Print to the following
port" setting of the printer driver.
6-4
CHAPTER 6 TCP/IP PEER TO PEER PRINTING
Other Sources of Information
1. Visit http://solutions.brother.com/ for more information on network
printing.
2. Refer to chapter 1 of this user guide to learn how to configure the IP
address of the FAX/MFC.
6-5
CHAPTER 7 NETBIOS PEER-TO-PEER PRINTING
CHAPTER SEVEN
71
7
NetBIOS Peer to Peer
Printing
How to Printing using NetBIOS
®
on Windows
®
95/98/Me/NT /2000/XP
Overview
Brother's Print / Fax server range supports SMB (Server Message Block) over the
TCP/IP protocol via the NetBIOS interface. This means that just like regular
®
Windows PC’s, Brother printers can appear in your network neighborhood. The
main advantage of NetBIOS printing is that you are able to print from legacy
DOS applications that are running on PC’s that are connected to Microsoft
networks.
Quick Tips:
1. The default IP address of Brother Print / Fax servers is 192.0.0.192. To
change it, use the FAX/MFC’s front panel , the BRAdmin application, or
let your DHCP server allocate an IP address to the printer
2. Refer to chapter 1 of this user guide to learn how to configure the IP
address on your printer.
3. The default login names are “user” for users and “admin” for
administrators and the default password for Brother Print / Fax servers is
"access".
4. The default domain name of the Print / Fax server is WORKGROUP, to
change it use your web browser or the BRAdmin application.
7-1
CHAPTER 7 NETBIOS PEER-TO-PEER PRINTING
Print / Fax Server Configuration
In order for this function to work, you must correctly change the DOMAIN name
or WORKGROUP name to match that of your network. Once this is done, the
Print / Fax server will appear automatically in your network neighborhood and
you will be able to send print documents to it without having to install additional
®
software. However, in some instances you may find that your Windows
®
®
95/98/Me and Windows NT 4.0/2000/XP systems may receive "Printer is busy"
error messages when more that one person attempts to access the FAX/MFC. In
this instance Brother has provided the "Brother NetBIOS Port Monitor" software
which allows users to continue spooling print jobs while the printer is busy, down
or out of paper. The port monitor will hold the jobs until the printer is again
available.
®
When you install Windows 95/98/Me you are asked which workgroup you
®
belong to, the default workgroup name for Windows 95/98/Me is
"WORKGROUP", however you could change this to anything you want. With
®
®
Windows NT , Microsoft introduced the concept of "Domains". A domain
offers centralized security management where as a workgroup offers distributed
security management. The Print / Fax server does not care if your network
consists of a Workgroup or a Domain, the only thing you must tell it is the name
of the workgroup or domain. The Brother Print / Fax server automatically has a
default workgroup/domain name of "WORKGROUP". If you need to change
name, you can configure the Brother Print / Fax server to recognize this. There
are four ways of doing this (If you are unsure about the name of your workgroup
or domain, look in the identification tab in your network applet).
•
•
•
•
Use BRAdmin (This utility can use the TCP/IP protocol or Netware IPX
protocol - no file server necessary.)
Use a Web browser, (the Print / Fax server must have a valid IP address and
your computer must also have a valid IP address); you can configure the IP
address by using BRAdmin.
TELNET, again your computer and printer must have a valid IP address.
Use BRCONFIG for DOS (this utility requires a Netware file server and the
IPX protocol).
Because of the way that Microsoft networks work, the Print / Fax server may
take several minutes to appear in the network neighborhood. You will also find
that the Print / Fax server may take several minutes to disappear from the
network neighborhood even if the printer is switched off. This is a feature of
Microsoft workgroup and domain based networks.
7-2
CHAPTER 7 NETBIOS PEER-TO-PEER PRINTING
Changing the workgroup/domain name
using TELNET or BRCONFIG or a web
browser
If you are unable to use the BRAdmin application or a web browser, you can use
TELNET or the BRCONFIG Remote console program (BRCONFIG requires the
IPX/SPX protocol to be installed on your PC).
When you are connected to the Print / Fax server, enter the default password
"access" in response to the "#" prompt. Type in anything in response to the
"Enter Username>" prompt, you will then be at the "Local>" prompt.
Now enter the command:
SET NETBIOS DOMAIN domainname
EXIT
Where domainname is the name of the domain or workgroup that you are on. If
you are not sure what your domain name or workgroup name is look in the
®
®
Identification tab in your Windows 95/98/Me/NT 4.0 network applet.
You can also use a standard WWW browser to change the NetBIOS name, to do
this connect to the Print / Fax server using its IP address and then select the
"Configure NetBIOS" option from the Print / Fax server configuration screen,
enter you workgroup/domain name into the "Domain Name" text box. Make sure
you submit the changes.
7-3
CHAPTER 7 NETBIOS PEER-TO-PEER PRINTING
NetBIOS Port Monitor for Windows®
95/98/Me, NT®4.0/2000/XP
This software requires the TCP/IP transport protocols to be installed on your
®
®
Windows 95/98/Me, NT 4.0/2000/XP computer. To install those protocols refer
®
to your Windows documentation.
If you are using the TCP/IP protocol, the proper IP address should be defined on
both the Brother Print / Fax server and your client PC.
Installing the Brother NetBIOS Port
Monitor
1. Start the CD-ROM (supplied with your FAX/MFC) installation menu
program according to the Quick Setup guide and select Install Software.
2. From the Network Applications menu select Install Software.
3. Click “Install” Network Print Software.
4. Push the Next button in response to the Welcome message.
5. Select Brother Peer-to-Peer Print (NetBIOS) installation.
6. Select the desired directory to install the Brother Network Direct Print
files and push Next.
7. Enter the Port name that you wish to use. The port name must start with
"BNT". For example BNT1. Whichever name you choose, it must be
unique. Then press "OK". The name must be unique on your PC,
however other computers can use the same port name as the name you
specify on your PC.
8. You must now enter the server name and port name for actual Print / Fax
server. You can use the Browse button for searching the Print / Fax
server, select the domain/workgroup name, and then the server is listed.
If the Print / Fax server does not automatically appear in your browse list,
then you must ensure that the domain name is configured correctly.
Otherwise you must enter the name manually. The name should be
compliant with UNC (Universal Name Convention). For example
"\\NodeName\ServiceName".
Where NodeName is the NetBIOS name of the Brother Print / Fax server
(the default name is usually BRN_xxxxxx, where "xxxxxx" is the last
six digits of the Ethernet address), and ServiceName is the service name
for NetBIOS of the Print / Fax server, by default it is BINARY_P1. For
example:
\\BRN_310107\BINARY_P1
You can find the NetBIOS name and MAC address by printing out the
FAX/MFC configuration page. Refer to the User’s Guide for information on how
to print the configuration page on your Print / Fax server.
9. Then press "OK".
10. Click the Finish button. You must now restart your computer before you
can continue.
7-4
CHAPTER 7 NETBIOS PEER-TO-PEER PRINTING
Associating the printer
®
1. You must now create a printer on your Windows 95/98/Me and
®
®
NT 4.0/2000/XP system using the standard Windows printer setup
procedure. To do this, go the Start button, select Setting and then
Printers.
®
Windows 95/98/Me
2. Select Add Printer to begin the printer installation.
3. Click Next when you get the add Printer Wizard window.
4. Select Local Printer when you are asked how the printer is connected to
your computer, and then push Next.
5. Select the correct driver. Click Next when you are done.
6. If you have selected a printer driver that is already being used, you have
the option of either keeping the existing driver (recommended) or
replacing it. Select the desired option and press Next.
7. Select the Brother NetBIOS Port (Port name you assigned in step 7 of
the Installing the Brother Peer-to-Peer Print (NetBIOS) section) and
press Next.
8. Enter any desired name for the Brother FAX/MFC and press Next. For
example, you could call the printer "Networked Brother Printer".
®
9. Windows will now ask you if you wish to print out a test page, select
Yes and then select Finish.
You are now ready to print. If necessary, you can share the printer on your PC so
that all print jobs are routed through your computer.
®
®
Windows NT 4.0/2000/XP
2. Select Add Printer to begin the printer installation.
3. Click Next when you get the add Printer Wizard window.
®
4. Select Local printer (Windows 2000) or Local printer attached to this
®
computer (Windows XP) when you are asked how the printer is
connected to your computer, and then push Next.
5. Select the Brother NetBIOS Port (Port name you assigned in step 6 of
the Installing the Brother Peer-to-Peer Print (NetBIOS) section ) and
press Next.
6. Select the correct driver. Click Next when you are done.
7. If you have selected a printer driver that is already used, you have the
option of either keeping the existing driver (recommended) or replacing
it. Select the desired option and press Next.
8. Enter any desired name for the Brother printer and press Next. For
example, you could call the printer "Networked Brother Printer".
9. Select not Shared or Shared and Share Name and press Next.
®
10. Windows will now ask you if you wish to print out a test page, select
Yes and then select Finish.
You are now ready to print. If necessary, you can share the printer on your PC so
that all print jobs are routed through your computer.
7-5
CHAPTER 7 NETBIOS PEER-TO-PEER PRINTING
Adding a Second NetBIOS Print Port
1. You do not need to re-run the installation program to add a new
NetBIOS port. Instead, press the Start button, select Settings, and open
®
the Printers Windows . Click on the icon of the printer that you wish to
configure, select File from the Menu bar, and then choose Properties.
®
Windows 95/98/Me
2. Click on the Details tab and push the Add Port button. In the Add Port
dialog, select the Other radio button and then highlight "Brother
NetBIOS port". Click OK and enter the port name. The default port
name is BNT1. If you have already used this name, you will get an error
message if you try to use it again, in which case use BNT2, etc… Once
you have specified the Port name, click the OK button. You will then see
the Port Properties Dialog. Enter the Print / Fax server and port name of
the printer that you wish to print to and click OK. You should now see
the port that you have just created in the "Print to the following port"
setting of the printer driver.
®
®
Windows NT 4.0/2000/XP
2. Click on the Ports tab and push the Add Port button. In the Add Port
dialog, highlight "Brother NetBIOS port". Click New Port and enter the
port name. The default port name is BNT1. If you have already used this
name, you will get an error message if you try to use it again, in which
case use BNT2, etc… Once you have specified the Port name, click the
OK button. You will then see the Port Properties Dialog. Enter the Print
/ Fax server and port name of the printer that you wish to print to and
click OK. You should now see the port that you have just created in the
"Print to the following port" setting of the printer driver.
7-6
CHAPTER 8 BIP INTERNET PRINTING INSTALLATION
CHAPTER EIGHT
81
8
How to Configure
Internet Printing for
®
Windows
®
95/98/Me/NT 4.0/
2000/XP
Internet Printing Installation
Overview
®
®
Brother's Brother Internet Print (BIP ) software, for Windows 95/98/Me/NT 4.0,
allows a PC user at one location, to send a print job to a Brother Printer at a
remote location via the Internet. For example, a user on a PC in New York could
print a document directly from his Microsoft Excel application program to a
printer in Paris.
®
Windows 2000/XP users can also use this BIP software, but are recommended
®
to use the IPP protocol support that is part of the Windows 2000 operating
®
systems. Skip to the “Windows 2000 IPP Printing” section of this document.
Quick Tips:
1. The default IP address of Brother Print / Fax servers is 192.0.0.192. To
change it, use the FAX/MFC’s front panel , the BRAdmin application, or
let your DHCP server allocate an IP address to the printer.
2. Refer to chapter 1 of this user guide to learn how to configure the IP
address on your printer.
3. The default password for Brother Print / Fax servers is "access".
®
4. Windows 2000/XP users can print using TCP/IP using the standard
Network Printing software and IPP protocol software built into any
®
Windows 2000/XP installation.
®
5. Windows 95/98/Me users can send print jobs using the IPP protocol via
®
Windows 2000/XP computer providing that the Microsoft Internet Print
Services software is installed on the client PC, IIS is installed and
running on the server and that the client PC is using version 4 or later of
Microsoft Internet Explorer.
8-1
CHAPTER 8 BIP INTERNET PRINTING INSTALLATION
Brother Internet Print
General Information
®
®
The BIP software is installed using a standard Windows 95/98/Me/NT
®
4.0/2000/XP Installation Wizard. It creates a virtual port on the Windows
®
95/98/Me/NT 4.0/2000/XP PC that operates in a similar way to the standard
LPT1 printer port from the Application program point of view. The user can use
®
®
the Windows 95/98/Me/NT 4.0/2000/XP Print Manager to create a printer that
®
®
uses this port along with a standard Windows 95/98/Me, NT 4.0/2000/XP ®
®
compatible printer. Any Windows 95/98/Me/NT 4.0/2000/XP applications
program can therefore print to this printer (and hence to the virtual port) without
modification or operational procedure.
When a job is printed to the BIP virtual port, it is actually MIME-encoded
(converted to a standard Internet E-mail message) and sent out to a Brother Print
/ Fax server at the remote location using Winsock This means that BIP is
compatible with most common E-mail software packages. The only requirement
is that the E-mail server be capable of sending E-mail message over the Internet.
In more detail, the procedure works in the following way:
•
If you are connected to a Local Area Network, the E-mail message is passed
to the E-mail server, which in turn transmits the message out over the
Internet using the SMTP protocol (Simple Mail Transport Protocol) to the
remote Print / Fax server.
•
If you are connecting via a modem directly to an Internet Service Provider
(ISP), the ISP handles the routing of the E-mail to the remote Print / Fax
server.
•
At the remote site, an E-mail server receives the E-mail message. The
remote Print / Fax server, which has its own E-mail address, uses the POP3
protocol (Post Office Protocol 3) to download the E-mail message from the
server. It then decodes the attachment and prints it out on the printer.
If an E-mail is received that has not been configured to use the BIP virtual port
driver, the printer will print the e-mail out as a text document.
8-2
CHAPTER 8 BIP INTERNET PRINTING INSTALLATION
Brother Internet Print
Configuring the Brother Print / Fax server
The Print / Fax server can be configured using BRAdmin, by using a web
browser, or by using the TELNET command.
Print / Fax server Configuration Checklist
Before configuring the Print / Fax server to receive BIP jobs, be sure that the Email server at the remote site (the receiving end) is configured to handle the
TCP/IP POP3, and SMTP protocols (SMTP is only required if the notification
feature is enabled).
1. Configure the POP3 server on the E-mail server at the remote site with a
mail account (Mailbox name) and password for the Brother Print / Fax
server (generally, the mail account name will be the first part of the
Email address; for example, if you assign the Email address
emailprinter@xyz.com, then the mail account name would be
emailprinter).
2. Make sure that the Print / Fax server is installed and running with
TCP/IP enabled and has a valid IP address assigned to it.
Because access to the E-mail server on most networks is usually restricted, you
may need to have your network administrator check the configuration and add
the mail account.
8-3
CHAPTER 8 BIP INTERNET PRINTING INSTALLATION
Brother Internet Print
Using BRAdmin to Configure the Print / Fax
server
Skip this section if you wish to use the Print / Fax server remote console or Web
Browser to configure the Print / Fax server.
Using the BRAdmin application, you can configure the Brother Print / Fax server
using the TCP/IP protocol, or the IPX protocol.
The steps required to configure the Print / Fax server to receive print jobs from a
®
®
Windows 95/98//Me/NT 4.0/2000/XP. PC running the BIP software is as
follows:
1. Start BRAdmin.
2. Select the node name of the desired Brother Print / Fax server from the
list and double clicking on it. (the default node name is usually
BRN_xxxxxx, where "xxxxxx" is the last six digits of the Ethernet
address (MAC address)). You will be prompted for a password, the
default password is "access".
You can find the node name and MAC address by printing out the FAX/MFC’s
configuration page. Refer to the Quick Network Setup Guide for information on
how to print the configuration page on your Print / Fax server.
3. Click on the Internet tab.
4. Enter the IP address of the POP3 server (consult your network
administrator if you do not know this address).
5. Enter the mailbox name for the remote Brother Print / Fax server.
Usually this will be the first part of the E-mail address (for example, if
the E-mail address of the Print / Fax server is emailprinter@xyz, then the
mailbox name would be emailprinter).
6. Enter the password for the mailbox, if any.
7. The Print / Fax server is configured by default to poll the POP3 server
every 10 minutes. You may change this value, if desired.
8. If you have enabled notification, enter the IP address of your SMTP
server (consult your network administrator if you do not know this
address).
9. Press the OK button and save the changes. Now exit the BRAdmin
application. You have now configured the Print / Fax server to receive
print jobs.
8-4
CHAPTER 8 BIP INTERNET PRINTING INSTALLATION
Brother Internet Print
Using a Web Browser to configure the Print /
Fax server
1. Connect to the printer server IP address using your web browser.
2. When you reach the network configuration screen, you will be prompted
for a password. The default password is "access"
3. Select the Configure Internet option and enter the information as
described above. Refer to "Using BRAdmin to Configure the Print / Fax
server"
4. You should see a Segmented Message Timeout option. If a print job is
separated into multiple E-mail messages using the Partial E-mail Print
feature of the BIP, this value indicates how long the Print / Fax server
will wait for all of the segments of the message to arrive.
8-5
CHAPTER 8 BIP INTERNET PRINTING INSTALLATION
Brother Internet Print
Using TELNET to Configure the Print / Fax
server
Skip this section if you used BRAdmin or a Web Browser to configure the
remote Print / Fax server.
As an alternative to BRAdmin, you can use the Print / Fax server remote console
to configure the Print / Fax server. The console can be accessed via TELNET.
When you access the Print / Fax server using these utilities, you will be asked for
a password. The default password is "access".
1. When you get the "Local>" prompt after connecting to the console, enter
the command:
SET
POP3
ADDRESS
ipaddress
where ipaddress is the IP address of your POP3 server (consult with your
network administrator if you do not know this address).
2. Enter the command:
SET
SET
POP3
POP3
NAME mailboxname
PASSWORD emailpassword
where mailboxname is the name of the remote Print / Fax server mailbox
and emailpassword is the password associated with this mailbox.
Usually the mailbox name is the same as the first part of the E-mail
address that you defined previously (for example, usually if the E-mail
address is emailprinter@xyz.com, then the mailbox name is
emailprinter).
3. The Print / Fax server is set by default to poll the POP3 server every 10
minutes. If you wish to change this value, enter the command:
SET
POP3
POLLING
rate
where rate is the polling rate in minutes.
Type EXIT to exit the console and save the changes. You have now
completed configuring the Print / Fax server.
8-6
CHAPTER 8 BIP INTERNET PRINTING INSTALLATION
Brother Internet Print
Installing the BIP software on Windows®
95/98/Me/NT® 4.0/2000/XP
®
®
To install the BIP software on a Windows 95/98/NT 4.0 PC, execute the
following steps:
•
•
Be sure that the PC is running an E-mail program (for example, Microsoft
Outlook) that is capable of sending E-mail message using Winsock.
Be sure that your E-mail server is capable of sending messages across the
Internet.
Setup from CD-ROM
1. Start the CD-ROM (supplied with your FAX/MFC) installation menu
program according to the Quick Setup guide and select Install Software.
2. From the Network Applications menu select Install Software.
3. Click “Install” Network Print Software.
4. Push the Next button in response to the Welcome message.
5. Select the Brother Internet Print button.
6. Select the desired directory to install the BIP files and then push Next.
The installation program will create the directory for you if it does not
already exist.
7. You will then be asked for a port name. Enter the name of the port. The
port name must begin with the BIP and end with a number, for example,
BIP1.
8. You will then see a message about Partial E-mail Print. Partial E-mail
Print is the ability of the Brother Internet Print software to break down
E-mail Print jobs into smaller sections to prevent a mail file size
limitation problem for mail server.
9. Press OK to continue.
8-7
CHAPTER 8 BIP INTERNET PRINTING INSTALLATION
10. You will then be asked to enter the port settings for the remote Print /
Fax server:
Enter any unique legal Internet E-mail address for the remote Print / Fax
server (for example emailprinter@xyz.com). Note that Internet E-mail
addresses cannot have spaces in them.
Enter your E-mail address and the IP address of your SMTP E-mail
server (consult your network administrator if you do not know this
address). Also specify if you are going to use the Partial E-mail Print
option and Notification type.
11. Press OK to continue. You will then be asked to re-start your computer.
12. Once your computer has re-started you must create a printer on your
®
®
Windows 95/98/Me/NT 4.0/2000/XP system using the standard
®
®
Windows 95/98/Me/NT 4.0/2000/XP printer setup procedure. To do
®
this, go the Start button, select Settings and then Printers (Windows
®
95/98/Me/NT 4.0/2000/XP). To do this, go to the Control Panel, select
Printers and Other Hardware and then Printers and Faxes (or Add a
®
printer) (Windows XP).
13. Select Add Printer to begin the printer installation.
14. Click Next when you get the Add Printer Wizard window.
®
(For Windows 95/98/Me user)
15. Select Local Printer, when you are asked how the printers are connected
to your computer and push Next.
®
®
(For Windows NT 4.0/2000 user)
15. Select Local Printer, and then delete the check mark in Plug and Play
check box.
®
(For Windows XP user)
15. Select Local Printer attached to this comuputer.
8-8
CHAPTER 8 BIP INTERNET PRINTING INSTALLATION
®
<For Windows 95/98/Me users>
15. Select the desired model of the remote printer (for example, Brother HLseries). If necessary, click Have Disk to load the driver from the
installation CD ROM diskette. Click Next when you are done.
16. If you have selected a printer driver that is already being used, you have
the option of either keeping the existing driver (recommended) or
replacing it. Select the desired option and press Next.
17. Select the Brother Internet port (BIP...) which you select in step 6 and
press Next.
®
®
<For Windows NT 4.0/2000/XP users>
15. Select the Brother Internet port (BIP...) which you select in step 6 and
press Next.
16. Select the desired model of the remote printer (for example, Brother HLseries). If necessary, click Have Disk to load the driver from the printer's
installation diskette. Click Next when you are done.
17. If you have selected a printer driver that is already being used, you have
the option of either keeping the existing driver (recommended) or
replacing it. Select the desired option and press Next.
18. Enter any desired name for the BIP remote printer and press Next. Note
that this name does not need to match the Port name that you assigned in
step 7, or E-mail address that you assigned in step 10..
19. Select No when asked if you want to print a test page, unless you have
already configured the remote Print / Fax server to receive BIP print jobs.
You have now finished installing the BIP software. If you need to configure
another remote Print / Fax server, go to next section, Adding a Second Brother
Internet Port.
8-9
CHAPTER 8 BIP INTERNET PRINTING INSTALLATION
Adding a Second Brother Internet Port
You should not re-run the install program to add a new Brother Internet Port.
®
Instead, press the Start button, select Settings, and open the Printers Windows .
Click on the icon of a printer that is using BIP, select File from the menu bar, and
®
®
then choose Properties. Click on the Details (Ports on Windows NT ) tab and
push the Add Port button.
®
In the Add Port dialog, select the Other radio button (Windows 95/98/Me only)
®
®
and then "Brother Internet Port". Click OK (New Port on Windows NT ) and it
will give you the Port Name. Any unique name can be given here as long as it
starts with "BIP" and another port does not already exist with the same name.
8-10
CHAPTER 8 BIP INTERNET PRINTING INSTALLATION
Windows® 2000/XP IPP Printing
Use the following instructions if you wish to use the IPP printing capabilities of
®
Windows 2000.
1. Run the Add Printer Wizard and click the Next button when you see the
“Welcome to the Add Printer Wizard” screen.
2. You are now able to select “Local Printer” or “Network Printer”. Make
sure that you select “Network Printer”.
3. You will see the “Add Printer Wizard” screen.
4. Select the “Connect to a printer on the Internet or on a home or office
network” and then enter the following in the URL: field:
http://printer_ip_address:631/ipp (Where “printer_ip_address” is the
IP address or DNS name of your printer.)
®
5. When you click “Next”, Windows 2000/XP will make a connection
with the URL that you specified.
IF THE PRINTER DRIVER HAS ALREADY BEEN INSTALLED
®
If the appropriate printer driver is already installed on your PC, Windows
2000/XP will automatically use that driver for use. In this case, you will simply
be asked if you wish to make the driver the default driver, after which the Driver
installation Wizard will complete. You are now ready to print.
IF THE PRINTER DRIVER HAS NOT BEEN INSTALLED
One of the benefits of the IPP printing protocol is that it establishes the model
name of the printer when you communicate with it. After successful
communication you will see the model name of the printer automatically, this
®
means that you do not need to inform Windows 2000 the type of printer driver
to be used.
6. Click “OK”, you will then see the following Printer selection screen in
the Add Printer Wizard.
7. If your printer is not in the list of supported printers, click the “Have
Disk” button. You will then be asked to insert the driver disk.
8. Click the “Browse” button and select the CD-ROM or network share
that contains the appropriate Brother printer driver.
9. Now specify the model name of the printer
10. If the printer driver that you are installing does not have a Digital
Certificate you will see a warning message. Click “Yes” to continue with
the installation. The Add Printer Wizard will then complete.
11. Click the “Finish” button and the printer is now configured and ready to
print. To test the printer connection, print a test page.
8-11
CHAPTER 8 BIP INTERNET PRINTING INSTALLATION
Specifying a different URL
Please note that there are several possible entries that you can enter for the URL
field.
http://printer_ip_address:631/ipp
This is the default URL and we recommend that you use this URL. Please note
the “Get More Info” option will not display any printer data
http://printer_ip_address:631/ipp/port1
This is for HP JetDirect compatibility. Please note the “Get More Info” option
will not display any printer data
http://printer_ip_address:631/
If you forget the URL details, you can simply enter the above text and the printer
will still receive and process data. please note the “Get More Info” option will
not display any printer data
If you are using the built in service names that the Brother NC-8100h series Print
/ Fax server supports, you can also use the following (however, please note the
“Get More Info” option will not display any printer data
http://printer_ip_address:631/brn_xxxxxx_p1
http://printer_ip_address:631/binary_p1
http://printer_ip_address:631/text_p1
http://printer_ip_address:631/postscript_p1
http://printer_ip_address:631/pcl_p1
http://printer_ip_address:631/brn_xxxxxx_p1
Where printer_ip_address is the IP address of the printer.
8-12
CHAPTER 9 NOVELL NETWARE PRINTING
CHAPTER NINE
91
9
Novell NetWare Printing
How to configure Novell
NetWare Printing
Overview
Brother Print / Fax servers allow NetWare client PCs to print jobs on the same
printer as TCP/IP or other network protocol users. All NetWare jobs are spooled
through the Novell server and delivered to the printer when it is available.
Quick Tips:
1. The default IP address of Brother Print / Fax servers is 192.0.0.192. To
change it, use the print front panel (if applicable), the BRAdmin
application, or let your DHCP server allocate an IP address to the printer.
2. The default password for Brother Print / Fax servers is "access".
9-1
CHAPTER 9 NOVELL NETWARE PRINTING
General Information
In order to use a Brother Print / Fax server on a NetWare network, one or more
file servers must be configured with a print queue that the Print / Fax server can
service. Users send their print requests to the file server's print queue, and the
jobs are then spooled (either directly, or in the case of remote printer mode, via
an intermediate Print / Fax server) to the appropriate Brother Print / Fax server.
The system administrator can create Bindery (NetWare 3), NDS (NetWare 3 and
NetWare 4) based queues in a single environment without having to switch
between applications by using the BRAdmin application.
NetWare 5 users wishing to configure an NDPS printer must use the NWADMIN
application supplied with NetWare 5. Please note that it is possible to create IPX
BINDERY or NDS based queues on a NetWare 5 system using the BRAdmin
application.
You must install the Novell NetWare Client 32 if you wish to create queue
information on your NetWare servers using the BRAdmin application.
If you can't use the BRAdmin application in your environment, you can create
the queue using the traditional NetWare PCONSOLE utility or NWADMIN
utilities, but you will then also need to use the Brother BRCONFIG utility,
TELNET or a WWW browser to configure the Print / Fax server as described
later in this chapter.
Brother Print / Fax servers can service up to 16 file servers and 32 queues.
9-2
CHAPTER 9 NOVELL NETWARE PRINTING
Creating a NDPS Printer Using NWADMIN
for NetWare5
With NetWare 5, Novell has released a new preferred printing system called
Novell Distributed Print Services (NDPS). Before the Print / Fax server can be
configured, NDPS must be installed on the NetWare 5 server and an NDPS
Manager configured on the server.
For further information regarding NDPS printers and printing please refer to the
“Other Sources of Information” section at the end of this chapter.
NDPS Manager
This creates a NDPS manager that interacts with services running at the server
and manages an unlimited number of printer agents.
You have to create an NDPS manager within an NDS tree before creating serverbased printer agents. If the NDPS manager controls a printer attached directly to
the server, you must load the manager on the server that the printer is attached to.
1. In NetWare administrator, navigate to the area you want the NDPS
manager to reside. Select Object | Create | NDPS Manager and click OK.
2. Enter an NDPS manager name
3. Browse to a server (which has NDPS installed but no NDPS manager
installed) where you want to install the NDPS manager and then to the
volume you want the NDPS manager database assigned to. Click create.
NDPS Broker
When NDPS is installed, an NDPS broker is loaded onto the network. One of the
Broker services Resource Management Service allows Printer Drivers to be
installed onto the server for use with Printer Agents.
To add a Printer Driver to the Broker:
4.
5.
6.
7.
Make sure the Resource Management Service is enabled.
Open the Broker Object's main window in NetWare Administrator
Select the Resource Management view.
The Resource Management dialog appears. Select the Add Resources
button.
8. When the Manage Resources dialog appears, select the icon for the type
of driver you want to add. This will be a 3.1x, 95/98/Me or NT4.0 driver
for NetWare 5. If you are using NDPS version 1 with NetWare 4.x only
3.1x and 95/98/Me options will be available. NDPS version 2 for
NetWare 4.x will support NT drivers automatic download.
9-3
CHAPTER 9 NOVELL NETWARE PRINTING
9. A complete list of currently loaded resources of that type appears in the
Current Resources window. Click the Add button.
10. The Add <resource type> dialog appears. The listed resources that
appear on this screen are currently installed.
11. Press the Browse button to locate the driver you want to add to the list.
The driver list appears possibly showing several printers. This should be
the driver in different languages supported.
Creating a Printer Agent
1. In NetWare Administrator, select object | create | NDPS Printer. Enter
the NDPS printer name.
For further information regarding NDPS printers and printing please refer to the
“Other Sources of Information” section at the end of this chapter.
2. If this is a new printer select create A New Printer Agent.
3. If there is already an NDS printer and you are upgrading it to use the
NDPS scheme, select Existing NDS printer object. You will then have to
select which printer object you wish to upgrade.
4. Enter the name you wish the Printer Agent to be referred to and either
type the name of the NDPS Manager or click the radio button and select
a NDPS Manager. Select the type of Port for the Printer Agent and Click
OK.
5. You must now specify the type of connection that you are going to use.
There are four possible options. Select the LPR over IP option.
6. Enter the relevant details of the printer and Brother recommend typing
Binary_P1 for the printer name. Click finish and wait. Select the printer
drivers for the client operating systems.
You are now ready to print.
9-4
CHAPTER 9 NOVELL NETWARE PRINTING
Configuring Netware 3 and NetWare 4
systems
Brother's BRAdmin application provides similar functionality to the NetWare
PCONSOLE utility (or the NWADMIN utility in NetWare 4.1x or later). To use
the BRAdmin application to configure a Brother Print / Fax server under
NetWare, make sure that you are logged in as SUPERVISOR (NetWare 2.xx or
3.xx) or ADMIN (NetWare 4.1x or later) and perform the appropriate steps as
detailed in the following pages.
You must install the Novell NetWare Client 32 if you wish to create queue
information on your NetWare servers by BRAdmin.
9-5
CHAPTER 9 NOVELL NETWARE PRINTING
Configuring the Brother Print / Fax server
(Queue Server Mode in Bindery emulation
mode) using BRAdmin
1. Make sure that you logged in as SUPERVISOR (NetWare 2.xx or 3.xx)
or ADMIN (NetWare 4.xx or later).
2. Start BRAdmin.
3. One or more Print / Fax server will appear in the list (the default node
names are BRN_xxxxxx, where "xxxxxx" is the last six digits of the
Ethernet address (MAC address)).
You can find the node name and MAC address by printing out the FAX/MFC’s
configuration page. Refer to the Quick Network Setup Guide for information on
how to print the configuration page on your Print / Fax server.
4. Select the Print / Fax server that you wish to configure and double click
it. You will be asked for a password. The default password is "access".
5. Select the NetWare tab.
If necessary change the "Print / Fax server Name", the default NetWare Print /
Fax server name will usually be BRN_xxxxxx_P1 where xxxxxx is the Ethernet
address of the Print / Fax server. Be careful! Changing the name may impact the
configuration of other protocols because the Print / Fax server service names will
be altered.
a.
b.
c.
d.
e.
f.
If it is not already selected, select Queue Server mode.
Click the Change Bindery Queues button.
Select the NetWare server which you wish to configure.
Select the New Queue button and type in the queue name which you
wish to create.
Once you have done that highlight the queue name you created and
click on the Add button.
Click on Close and then OK.
Now exit the BRAdmin application. You are ready to print.
9-6
CHAPTER 9 NOVELL NETWARE PRINTING
Configuring the Brother Print / Fax server
(Queue Server Mode in NDS mode) using
BRAdmin
1. Make sure that you logged in as ADMIN in NDS mode.
2. Start BRAdmin.
3. One or more Print / Fax server services will appear in the list of printers
(the default node names are BRN_xxxxxx, where "xxxxxx" is the last
six digits of the Ethernet address (MAC address)).
You can find the node name and MAC address by printing out the FAX/MFC’s
configuration page. Refer to the Quick Network Setup Guide for information on
how to print the configuration page on your Print / Fax server.
4. Select the printer that you wish to configure and double click it. You will
be asked for a password. The default password is "access".
5. Select the NetWare tab.
a.
b.
c.
d.
e.
f.
If it is not already selected, select Queue Server mode.
Select the correct NDS tree and NDS context (you can manually
enter this information, or by clicking on the down arrow by the side
of NDS tree and the Change button by the side of NDS Context,
you can let BRAdmin display your choices automatically. Once you
have specified this information, click on the Change NDS queues
button.
In the NetWare Print Queues screen select the appropriate TREE
and Context and then Click the New Queue button.
Enter the queue name and specify the volume name. If you do not
know the volume name, select the Browse button to browse the
NetWare volumes. When the information is entered correctly, select
the OK button.
Your queue name will appear in the TREE and Context that you
specified. Select the queue and click on Add. The queue name will
then be transferred to the Service Print Queues Window. You will
be able to see the TREE and Context information along with the
queue name information in this Window.
Click on the Close button. Your Brother Print / Fax server will now
log into the appropriate NetWare server.
Now exit the BRAdmin application. You are ready to print.
9-7
CHAPTER 9 NOVELL NETWARE PRINTING
Configuring the Brother Print / Fax server
(Queue Server Mode in NDS mode) using
Novell NWADMIN and BRAdmin
If you do not wish to use the Brother BRAdmin application solely to configure
your NetWare file server, use the following instructions for configuration using
the NWADMIN application in conjunction with the BRAdmin application.
1. Make sure that you are logged in as ADMIN in NDS mode on the
NetWare 4.1x (or later) file server and start the NWADMIN application.
2. Select desired Context that will contain the Printer and then click on
Object from the menu bar and then Create. When you get the New
Object menu, select Printer and then OK.
3. Enter the name of the printer and select Create.
4. Select the desired Context that will contain the default print queue, and
then click on Object and Create to get New Object menu.
5. Select Print Queue and then OK. Make sure that Directory Service
Queue is selected and then type in a name for the default print queue.
6. Click on the button to select the print queue volume. Change the
directory context if necessary, then select the desired volume (from
Available Objects) and click OK. Click Create to create the print queue.
7. Change context if required and then double click the name of the printer
you created in step 3.
8. Click Assignments and then Add..
9-8
CHAPTER 9 NOVELL NETWARE PRINTING
Change the context if necessary and select the print queue you created in step 5.
9. Click Configuration and set the Printer type to Other/Unknown. Click
OK and then OK again.
10. Change the context if required, select Object from the menu bar and then
Create. When you get the New Object menu, select Print / Fax server
and then OK.
11. Enter the name of the Print / Fax server and select Create.
Enter the NetWare Print / Fax server name of the Print / Fax server exactly as it
appeared in the NetWare tab of the BRAdmin application (this will generally be
the BRN_xxxxxx_P1 default service name, unless you changed the name).
You can find the current service name and MAC address by printing out the
FAX/MFC’s configuration page. Refer to the Quick Network Setup Guide for
information on how to print the configuration page on your Print / Fax server.
Important:
Do not assign a password to the Print / Fax server or it will not log in.
12. Double click on the name of your Print / Fax server. Click on
Assignments and then Add...
13. If necessary, change the directory context. Select the printer you created
in step 3 and click OK and then OK again.
14. Exit NWADMIN.
15. Start the appropriate BRAdmin application, and select the correct Print /
Fax server from the list (by default, the node name is BRN_xxxxxx,
where "xxxxxx" is the last six digits of the Ethernet address (MAC
address)).
Double click the appropriate Brother Print / Fax server. You will be prompted for
a password, the default password is "access". Now select the NetWare tab.
16. Select Queue Server as the operating mode.
The same service assigned by NetWare server name cannot be used for both
queue server mode and remote printer mode.
If you want to enable queue server capabilities on services other than the default
NetWare services, you must define new services that are enabled for NetWare
and for the desired port. Refer to the Appendix in this manual for information on
how to do this.
17. Enter the NDS tree name (note that a Print / Fax server can service both
NDS and bindery queues).
18. Type in the name of the context where the Print / Fax server resides.
19. Exit the BRAdmin application making sure that you save the changes
that you have made. You are now ready to print.
9-9
CHAPTER 9 NOVELL NETWARE PRINTING
Configuring the Brother Print / Fax server
(Remote Server Mode in NDS mode) using
Novell NWAdmin and BRAdmin
To configure a Brother Print / Fax server for remote printer mode with
NWADMIN (NetWare Administrator utility) and BRAdmin, you will need to
perform the following steps:
1. Make sure that the PSERVER NLM (NetWare Loadable Module) is
loaded on your file server and that you are logged in as ADMIN in NDS
mode on the NetWare 4.1x file server.
2. Start NWADMIN by double clicking on the icon. Select the desired
Context that will contain the new printer.
3. Select Object from the menu bar and then Create. When you get the New
Object menu, select Printer and then OK.
4. Enter the name of the printer and select Create.
5. Double click on the Print / Fax server name of your PSERVER NLM.
Click on Assignments and then Add.
6. If necessary, change the directory context. Select the printer you created
and click OK. Note the number of the printer, as you will use this later,
then click OK.
7. Select the desired Context that will contain the default print queue, and
then click on Object and Create to get New Object menu.
8. Select Print Queue and then OK. Make sure that Directory Service
Queue is selected, and then type in a name for the default print queue.
9-10
CHAPTER 9 NOVELL NETWARE PRINTING
9. Click on the button to select the print queue volume. Change the
directory context if necessary, then select the desired volume (Objects)
and click OK. Click Create to create the print queue.
10. Change context if required and then double click the name of the printer
you created previously.
11. Click Assignments and then Add.
12. Change context if necessary and select the print queue you created. Click
OK and then OK again, and then exit NWADMIN.
13. Start the appropriate BRAdmin application, and select the correct Print /
Fax server you wish to configure (by default, the node names will begin
with BRN_xxxxxx_P1 )
You can find the NetWare server name and MAC address by printing out the
FAX/MFC’s configuration page. Refer to the Quick Network Setup Guide for
information on how to print the configuration page on your Print / Fax server.
14. Double click the appropriate Print / Fax server. You will be prompted
for a password, the default password is "access".
15. Now select the NetWare tab.
16. Select Remote Printer as the Operating Mode, select the name of your
PSERVER NLM as the Print / Fax server Name and select the number
of the printer from step 6 as the Printer Number.
The same service assigned by NetWare Print / Fax server cannot be used for both
queue server mode and remote printer mode. If you want to enable remote printer
capabilities on a service other than the default NetWare service, you must define
new services that are enabled for NetWare and for the desired port. Refer to
Appendix B in this manual for information on how to do this.
17. Click OK. And exit BRAdmin.
You must now unload the PSERVER NLM from your NetWare file server
console and then reload it in order for the changes to take effect.
As an alternative to Brother's BRAdmin application or the Novell NWADMIN
application, you can use the standard Novell PCONSOLE utility in conjunction
with Brother's BRCONFIG program to set up your print queues. BRCONFIG
program will be installed at the same time when you install the BRAdmin and
you can find the BRCONFIG in the menu "Start/Program/Brother BRAdmin
utilities". Otherwise you can find it on the CD-ROM supplied with your
FAX/MFC. Note that if desired, you may use a WWW browser or TELNET
utility - instead of the BRCONFIG utility).
9-11
CHAPTER 9 NOVELL NETWARE PRINTING
Configuring the Brother Print / Fax server
(Queue Server Mode in Bindery emulation
mode) using PCONSOLE and BRCONFIG
1. Login as Supervisor (NetWare 3.xx) or ADMIN (NetWare 4.1x or later;
be sure to specify the /b option for bindery mode).
®
2. Execute the BRCONFIG from the Windows menu or insert the "Print /
Fax server Configuration Utility diskette in drive A: and type the
following at the DOS prompt:
A:BRCONFIG or A:BRCONFIG PrintServerName
Where PrintServerName is the NetWare print service name of the
Brother Print / Fax server (the default name is BRN_xxxxxx_P1, where
"xxxxxx" is the last six digits of the Ethernet address (MAC address)).
You can find the NetWare print service name and MAC address by printing out
the FAX/MFC’s configuration page. Refer to the Quick Network Setup Guide for
information on how to print the configuration page on your Print / Fax server.
3. If you did not specify the Print / Fax server name in the BRCONFIG
command, select the corresponding server name from the list of Print /
Fax servers.
4. When you get the message that the Print / Fax server is connected, type
the default password "access" in response to the "#" prompt (the
password will not echo), and then press the ENTER key in response to
the Enter Username> prompt.
5. When you get the Local> prompt, type:
6. SET NETWARE SERVER servername ENABLED
7. Where servername is the name of the file server on which the print
queue will reside. If there is more than one file server that you wish to
print from, repeat this command as many times as necessary.
9-12
CHAPTER 9 NOVELL NETWARE PRINTING
8. Type EXIT to exit the BRCONFIG remote console program and save
the changes and start the Novell PCONSOLE utility.
9. Select Print / Fax server Information (NetWare 3.xx) or Print / Fax
servers (NetWare 4.1x; ignore the warning message) from the Available
Options menu.
10. You will be shown a list of current Print / Fax servers. Press the
INSERT key to create a new entry, type in the NetWare Print / Fax
server name (BRN_xxxxxx_P1 or BRO_xxxxxx_P1 by default, where
"xxxxxx" is the last six digits of the Ethernet address) and press ENTER.
Return to the main Available Options menu by pressing ESCAPE.
11. Select the Print Queue Information (NetWare 3.xx) or Print Queues
(NetWare 4.1x) menu option to see list of configured print queues.
12. Press INSERT to create a new queue on the file server, type the new
queue name and press ENTER. The name does not have to be related to
the name of the Print / Fax server resources, but should be short and
convenient for users to remember.
13. Make sure that the new queue name is highlighted, and then press
ENTER to configure the queue.
14. Select Queue Servers (in NetWare 4.1x, this item is called Print / Fax
servers) and press ENTER to specify which network Print / Fax servers
can print jobs from this print queue. The list will be empty, since none
have been selected yet if this is a new queue.
15. Press INSERT to get a list of the queue server candidates and select the
Print / Fax server service name from step 11, Press ENTER.
16. Press ESCAPE several times until you return to the Available Options
menu.
17. Force the Print / Fax server to rescan file servers for print jobs. You may
either turn the printer off and on again or you may down the Print / Fax
server in PCONSOLE as follows:
•
In the Available Options menu, highlight Print / Fax server
Information, and press ENTER.
•
Select the Print / Fax server name (BRN_xxxxxx_P1) and press
ENTER. If you have NetWare 4.1x, highlight Information and
Status and press ENTER, and then skip to the next bullet.
If you have NetWare 3.xx or 2.xx:
- Highlight Print / Fax server Status/Control and press ENTER.
- Highlight Server Info and press ENTER.
•
Push ENTER and then select Down and press ENTER again. This
will force the Print / Fax server to rescan the available file servers
for new queue entries.
•
Alternatively, use the BRCONFIG or TELNET command SET
NETWARE RESCAN to make the Print / Fax server rescan for file
servers.
9-13
CHAPTER 9 NOVELL NETWARE PRINTING
Configuring the Brother Print / Fax server
(Queue Server Mode in NDS mode) using
PCONSOLE and BRCONFIG
1. Make sure that you are logged in as ADMIN in NDS mode on the
NetWare 4.1x file server.
2. Run the PCONSOLE utility from PC workstation.
3. Select Print / Fax servers from the Available Options menu.
4. Press INSERT and enter the Print / Fax server Name
Enter the NetWare print service name of the Print / Fax server exactly as it
appeared in the printer configuration page (the default name is BRN_xxxxxx_P1,
where "xxxxxx" is the last six digits of the Ethernet address (MAC address),
unless you changed the name to something else). You can find the NetWare print
service name and MAC address by printing out the printer configuration page.
Refer to the Quick Setup Guide for information on how to print the configuration
page on your Print / Fax server.
Important:
Do not assign a password to the Print / Fax server or it will not log in.
5. Return to the main Available Options menu by pressing ESCAPE.
6. Select Print Queues.
7. Press INSERT type in the desired print queue name (you will also be
asked for a volume name. Press INSERT and select the appropriate
volume), and press ESCAPE to return to the main menu.
8. Make sure that the new queue name is highlighted, and press ENTER.
9. Select Print / Fax servers and press ENTER to specify which network
Print / Fax servers can print jobs from this print queue. The list will be
empty, since none have been selected.
10. Press INSERT to get a list of the queue server candidates and select the
NetWare Print / Fax server name from step 4, which will then be added
to the list. Press ENTER.
11. Select Printers from the Available Options menu.
12. Press INSERT and enter a descriptive name for the printer.
13. Press ESCAPE and go back to the Available Options menu.
14. Select Print / Fax servers and select the name of the printer server that
you entered in Step 4.
15. Highlight the Printers option in the Print / Fax server Information menu.
16. Press INSERT and select the name of the printers you entered in Step 12.
17. Press ESCAPE several times to return to DOS.
9-14
CHAPTER 9 NOVELL NETWARE PRINTING
®
18. Execute the BRCONFIG from the Windows menu or insert the CDROM that came with your FAX/MFC into the CD-ROM Drive of your
PC and type: X:BRCONFIG (X: is the drive letter of your CD-ROM
Drive).
Select the Print / Fax server from the list of Print / Fax servers. When
you get the message that the Print / Fax server is connected, press the
ENTER key and type the default password of "access" in response to the
"#" prompt (the password will not echo), and then press the ENTER key
again in response to the ENTER Username> prompt. When you get the
Local> prompt, type:
SET SERVICE service TREE tree
SET SERVICE service CONTEXT Context
•
•
•
•
Where tree is the NDS tree name.
Where context is the name of context where the Print / Fax server
resides.
Service is the name of the service assigned by NetWare Print / Fax
server name (where the default services are BRN_xxxxxx_P1 for
the Brother printer, where "xxxxxx" is the last six digits of the
Ethernet address (MAC address).
You can also enter the TREE and CONTEXT name using your web
browser by connecting to the Brother Print / Fax server using the
TCP/IP protocol and selecting the NetWare protocol configuration.
19. Use the BRCONFIG command or TELNET command: SET NETWARE
RESCAN to force the Print / Fax server to rescan for file servers, or
power cycle the printer.
The same services assigned by NetWare Print / Fax server names cannot be used
for both queue server mode and remote printer mode.
The same service assigned by NetWare Print / Fax server cannot be used for both
queue server mode and remote printer mode. If you want to enable remote printer
capabilities on a service other than the default NetWare service, you must define
new services that are enabled for NetWare and for the desired port. Refer to
Appendix B in this manual for information on how to do this.
9-15
CHAPTER 9 NOVELL NETWARE PRINTING
Configuring the Brother Print / Fax server
(Remote Printer Mode using PCONSOLE
and BRCONFIG
1. Make sure that the PSERVER NLM (NetWare Loadable Module) is
loaded on your file server.
2. Log into the file server from your PC workstation as ADMIN if you are
using NetWare 4.1x (if you want NDS support, do not login under
bindery mode). If you are using NetWare 2.xx or 3.xx, login as
SUPERVISOR.
3. Run the PCONSOLE utility from your PC workstation.
4. If you are creating a new print queue, select Print Queue Information
(NetWare 3.xx) or Print Queues (NetWare 4.1x) from the Available
Options menu.
5. Press INSERT, type in the desired print queue name (with NetWare 4.1x,
you will also be asked for a volume name; press INSERT and select the
appropriate volume), and press ESCAPE to return to the main menu.
The following steps apply to configuring a remote printer with NDS support
on NetWare 4.1x systems:
6.
a.
b.
c.
d.
e.
f.
g.
h.
i.
j.
Select Print / Fax servers from the PCONSOLE menu and then
select the name of the PSERVER NLM on your host computer.
Select Printers.
Press INSERT to get Object, Class menu.
Press INSERT and enter the Printer Name (any unique name is OK).
Highlight the printer name and press ENTER twice to get Printer
Configuration Menu.
PCONSOLE will assign a Printer Number. Remember this number,
since it will be used later.
Highlight Print Queues Assigned and press ENTER and then
INSERT to get a list of available queues.
Highlight the name of the print queue you wish to assign to the
remote printer and press ENTER.
The other settings in the menu are not required. Push ESCAPE
several times to exit PCONSOLE.
Skip to the Assigning the remote printer name and number sections
below.
9-16
CHAPTER 9 NOVELL NETWARE PRINTING
The following steps apply to configuring a remote printer on NetWare 3.xx
systems:
6.
a.
b.
c.
d.
e.
f.
g.
h.
i.
Select Print / Fax server Information from the PCONSOLE main
menu and choose the name of the PSERVER NLM.
Select Print / Fax server Configuration and then Printer
Configuration. Select any "Not Installed" printer and press Enter.
Remember the number of this printer, since it will be used later in
the configuration process.
If desired, type in a new name for the printer.
Go to Type, press ENTER, highlight Remote Other/Unknown and
press ENTER again. The other settings in this menu are not required.
Push ESCAPE and save the changes.
Push ESCAPE and select Queues Serviced by Printer.
Highlight the printer name that you just configured and press
ENTER.
Press INSERT, choose the desired print queue, and press ENTER
(you can accept the default priority).
Press ESCAPE several times to exit PCONSOLE.
9-17
CHAPTER 9 NOVELL NETWARE PRINTING
Assigning the Remote printer name and number using BRCONFIG
7.
a.
b.
®
Execute the BRCONFIG from the Windows menu or insert the
Brother Print / Fax server Software diskette in Drive A: of your PC
and type:
A:BRCONFIG
Select the Brother Print / Fax server from the list of Print / Fax
servers. When you get the message that the Print / Fax server is
connected, press the ENTER key and type Where the default
password "access" in response to the "#" prompt (the password will
not echo) and then press the ENTER key again in response to the
Enter Username> prompt. When you get the Local> prompt, type:
SET NETWARE NPRINTER nlm number ON service
SET NETWARE RESCAN
EXIT
•
•
•
Where nlm is the name of the PSERVER NLM on your file
server
Number is the printer number (must match the printer number
you selected during the PCONSOLE configuration in the
previous steps)
Service is the name of the service assigned by NetWare Print /
Fax server name(where the default services are
BRN_xxxxxx_P1 for the Brother printer, where "xxxxxx is the
last six digits of the Ethernet address (MAC address)).
For example, to set up remote "Printer 3" for a Brother FAX/MFC with the Print
/ Fax server BRN_310107_P1 using the PSERVER NLM called BROTHER1PS,
you would type:
SET NETWARE NPRINTER BROTHER1PS 3 ON BRN_310107_P1
SET NETWARE RESCAN
EXIT
•
You can also enter the remote printer name using your web browser by
connecting to the Brother Print / Fax server using the TCP/IP protocol and
selecting the NetWare protocol configuration.
The same services assigned by NetWare Print / Fax server name cannot be used
for both queue server mode and remote printer mode.
You must now unload the PSERVER NLM from your NetWare file server
console and then reload it in order for the changes to take effect.
9-18
CHAPTER 10 PRINTING FROM MACINTOSH
101
CHAPTER TEN
10
Printing From a
Macintosh
®
For Mac OS 8.6 – 9.2
System Requirements
For AppleTalk connection
Computer
Ethernet ready Power Macintosh
RAM
32MB or more (64MB or more recommended)
OS
Mac OS 8.6 - 9.2
Open Transport 1.3 or later
Printer Driver Installation
1. After starting up the Macintosh, insert the CD-ROM supplied with your
FAX/MFC.
2. Double click the "MFL Pro Suite Driver Installer" icon.
3. Proceed according to the instructions on the installer screen.
10-1
CHAPTER 10 PRINTING FROM MACINTOSH
Printer Driver Selection
After installing the printer driver, use the following steps to select the printer
driver. If no printer driver is selection, application software will not be able to
print.
1. Turn the power of the printer ON.
2. After starting up the Macintosh, click and open the Chooser from the
Apple menu.
3. Click the printer driver icon appropriate to the connection type.
For AppleTalk: MFL Pro (AT)
4. Select the printer connection destination.
For AppleTalk connections, the printer's AppleTalk service name (factory
shipment number BRN_XXXXXX_P1, XXXXXX for Ethernet (MAC address)
end 6 digits) will be shown in the connection destination list box.
Printing the configuration page will allow you to confirm the MAC address.
Please refer to the Quick Network Setup Guide on how to print the configuration
page.
5. Click the close box on the upper left of the dialog to end the setting.
10-2
CHAPTER 10 PRINTING FROM MACINTOSH
For Mac OS 10.1
System Requirements
For AppleTalk connection
Computer
Ethernet ready Power Macintosh
RAM
128MB or more (160MB or more recommended)
OS
Mac OS X 10.1
Printer Driver Installation
1.
2.
3.
4.
5.
After starting up the Macintosh, insert the CD-ROM supplied with
your FAX/MFC.
Double click the "MFL Pro Suite Driver Installer" icon.
Open the "Mac OS X" folder.
Double click the "BrotherHLMFLPro.pkg" icon.
Proceed according to the instructions on the installer screen.
Printer Driver Selection
After installing the printer driver, use the following steps to select the printer
driver. If no printer driver is on, application software will not be able to print.
1.
2.
3.
4.
5.
6.
7.
Turn the power of the printer ON.
Open the Applications folder.
Open the Utilities folder.
Open the Print Center Icon.
Click the “Add Printer” button.
Select Apple Talk
Select BRN_XXXXXX_P1 and click the Add button.
10-3
CHAPTER 10 PRINTING FROM MACINTOSH
For AppleTalk connections, the printer's AppleTalk service name (factory
shipment number BRN_XXXXXX_P1, XXXXXX for Ethernet (MAC address)
end 6 digits) will be shown as the Name.
Printing the configuration page will allow you to confirm the MAC address.
Please refer to the Quick Network Setup Guide on how to print the configuration
page.
8.
Select Quit Print Center from the Print Center menu.
The setup is now complete.
10-4
CHAPTER 11 DLC PRINTING
111
CHAPTER ELEVEN
11
DLC Printing
®
®
Printing from Windows NT or
®
Windows 2000
Overview
®
®
®
DLC is a simple protocol that is included in Windows NT and Windows 2000
®
as standard. It can be used on other operating systems (such as Windows 3.x)
with the addition of vendor-supplied software that supports the Hewlett-Packard
JetDirect card.
Quick Tips:
1. One way to print the details of all network settings is to print a
configuration page. Refer to the NC-8100h Quick Network Setup Guide
for information on how to print the configuration page.
Because DLC is a non-routable protocol, there cannot be a router between the
Print / Fax server and the sending computer.
11-1
CHAPTER 11 DLC PRINTING
Configuring DLC on Windows® NT®/2000
®
®
To use DLC on Windows NT , you must first install the DLC protocol.
®
®
1. Log into Windows NT with administrative privileges. Go to the NT
®
Control Panel and double click on the Network icon. Windows 2000
users select the properties of the Local Area Connection.
®
®
®
2. On Windows NT 3.5x systems, select Add Software. On Windows
®
®
NT 4.0 systems, click on the Protocol tab, and click Add. Windows
2000 users click the Install button from the General Tab.
®
3. Select DLC Protocol and then OK or Add if using Windows 2000. You
may be asked for the location of the files, for Intel based computers, the
®
®
necessary files are stored in the i386 directory of the Windows NT
CD-ROM. If you have a non-Intel platform, specify the correct directory
®
®
on your Windows NT CD-ROM. Click Continue (for 3.5x systems) or
Close (for 4.0 systems).
®
4. Reboot your system to make the change take effect. Windows 2000
should not require a re-boot.
11-2
CHAPTER 11 DLC PRINTING
Windows® 2000 Printer Setup
®
1. Log into Windows 2000 with administrative privileges. From the Start
menu, select Settings and then Printers.
2. Select Add Printer (If you have already installed a Brother printer driver,
double click the printer driver that you wish to configure and then select
Printers/Properties, select the Ports tab, Click on “Add Port” and
continue from Step 6 (ignoring steps 11-14) about installing the correct
driver).
3. Click Next.
4. Select Local Printer and make sure that “Automatically detect and install
my Plug and Play printer” is not checked.
5. Click Next
6. Select the “Create a new port:” option and highlight “Hewlett-Packard
Network Port”
7. Click Next
8. A list of available Print / Fax server MAC addresses (Ethernet addresses)
appears in the larger box under Card Address. Select the address of the
desired Print / Fax server (you can see the Ethernet address on the printer
configuration page)
You can find the node name and MAC address by printing out the printer
configuration page. Refer to the NC-8100h Quick Network Setup Guide for
information on how to print the configuration page on your Print / Fax server.
9. The selected Print / Fax server address will then appear in the smaller
box under Card Address.
10. Type in any desired name for the port (the name must not be the name of
an existing port or DOS device, such as LPT1) and click OK then on the
Printer Ports screen, click Next.
11. Select the correct driver click Next.
12. Give a name to the printer and specify if you wish to be able to print
from DOS application. Then click Next
13. Specify the share name (if you are going to share the printer).
14. Enter the Location and Comment information and click Next until you
see the “Completing the Add Printer Wizard” screen.
15. Click Finish
11-3
CHAPTER 11 DLC PRINTING
Windows® NT® 4.0 Printer Setup
®
®
Log into Windows NT with administrative privileges. From the Start menu,
select Settings and then Printers.
1. Select Add Printer (If you have already installed a Brother printer driver,
double click the printer driver that you wish to configure and then select
Printers/Properties, select the Ports tab and continue from Step 4
(ignoring steps 9-11) about installing the correct driver).
2. Select My Computer and then click Next.
3. Select Add a Port.
4. Select Hewlett-Packard Network Port and then click New Port.
5. A list of available Print / Fax server MAC addresses (Ethernet addresses)
appears in the larger box under Card Address. Select the address of the
desired Print / Fax server (you can see the Ethernet address on the printer
configuration page)
You can find the node name and MAC address by printing out the printer
configuration page. Refer to the Quick Network Setup Guide for information on
how to print the configuration page on your Print / Fax server.
6. The selected Print / Fax server address will then appear in the smaller
box under Card Address.
7. Type in any desired name for the port (the name must not be the name of
an existing port or DOS device, such as LPT1) and click OK then on the
Printer Ports screen, click Close.
8. The name you selected in the above step will appear as a checked port in
the list of available ports. Click Next.
9. Select the correct driver click Next.
10. Give a name to the printer. If desired, select the printer as the default.
11. Select Shared or Not Shared. If shared, specify the share name and
operating systems that will be printing to it.
12. Select whether or not you want a test page, and then select Finish.
11-4
CHAPTER 11 DLC PRINTING
Windows® NT® 3.5x Setup
®
®
1. From the Windows NT Main group, double click on the Print Manager
icon.
2. Select Printer from the menu bar and click on Create Printer.
3. Enter any desired name for the printer in the Printer Name box.
4. Select the printer model in the Driver menu.
5. Choose Other (or Network Printer for V3.1 systems) from the Print to
menu.
6. Click on Hewlett-Packard Network Port.
7. Type in your desired name for the port (this name must not be an
existing port or DOS device, such as LPT1).
8. The MAC addresses (Ethernet addresses) of available Print / Fax servers
will appear in the Card Address menu. Select the desired address (You
can see the Ethernet address on the printer configuration page)
You can find the node name and MAC address by printing out the printer
configuration page. Refer to the User’s Guide for information on how to print the
configuration page on your Print / Fax server.
9.
10.
11.
12.
Click OK.
If you want to share the printer, click Share the Printer on the Network.
Click OK.
If necessary, select the appropriate printer options and then click OK.
Configuring DLC on Other Systems
To use DLC on other network systems, you will generally need vendor-supplied
software. Typically such software will support the Brother Print / Fax servers.
Follow the vendor's instructions to install the DLC protocol on your system.
Once the protocol is installed, create a network port in the same way that you did
®
®
for Windows NT in the previous sections. The MAC address (Ethernet address)
of the Print / Fax server should automatically appear during the configuration
process.
The final step is to create a printer using the normal operating system printer
setup method. The only difference is that instead of connecting the printer to the
LPT1 parallel port, you point it to the network port you just created.
®
Brother does not recommend using the DLC protocol with Windows for
Workgroup 3.11 in a peer-to-peer configuration if the printer will be heavily used.
This is because jobs may be rejected due to print spooler timeouts. The best
solution in these situations is to set up one PC as a server for handling network
print jobs. All of the other PCs send their print jobs to the server PC using
NetBEUI or TCP/IP, and the server PC then uses DLC to send the print jobs to
the Brother Print / Fax server.
11-5
CHAPTER 12 UNIX PRINTING
121
CHAPTER TWELVE
12
Unix Printing
Printing from Unix/Linux using
TCP/IP
Overview
Brother Print / Fax servers are supplied with the Transmission Control
Protocol/Internet Protocol (TCP/IP) protocol suite. Since virtually all UNIX host
computers support TCP/IP, this capability allows a printer to be shared on a
UNIX Ethernet network.
The Linux operating system uses the same setup procedures as standard Berkeley
UNIX systems. Refer to this chapter for a typical GUI based Linux installation.
Quick Tips:
1. The default IP address of Brother Print / Fax servers is 192.0.0.192. To
change it, use the print front panel (if applicable), the BRAdmin
application or let your DHCP server allocate an IP address to the
FAX/MFC.
2. Refer to ‘chapter 1’ of this user guide to learn how to configure the IP
address on your FAX/MFC.
3. The default password for Brother Print / Fax servers is "access".
4. The default name for a Brother Print / Fax server is usually
BRN_xxxxxx (where xxxxxx is the last six digits of the Ethernet address
of the Print / Fax server).
5. When configuring the PRINTCAP file, pay particular attention to the
service names, BINARY_P1 and TEXT_P1
12-1
CHAPTER 12 UNIX PRINTING
TCP/IP
Brother Print / Fax servers appear to the network as a UNIX host computer with
a unique IP address running the lpd, line printer daemon, protocol. As a result,
any host computer that supports the Berkeley remote LPR command can spool
jobs to Brother Print / Fax servers without the need for any special software on
the host computer. For special applications, raw TCP ports are also available.
The Brother NC-8100h Print / Fax server also support the FTP protocol. This
protocol can be used to send print jobs from Unix systems.
The Brother Print / Fax server is pre-configured to run on a TCP/IP network with
a minimum of setup. The only mandatory configuration the Print / Fax server is
the allocation of an IP address, which can be either automatically assigned using
DHCP, BOOTP etc., or manually assigned using the ARP command, BRAdmin,
the FAX/MFC’s front panel , etc.
For setting the IP address of the Print / Fax server, refer to chapter 1 of this user
guide.
12-2
CHAPTER 12 UNIX PRINTING
General TCP/IP UNIX Host Configuration
The configuration process for most UNIX systems is described in the following
steps. As this process varies, we recommend that you refer to your system
documentation (or man pages) for additional information.
1. Configure the /etc/hosts file on each UNIX host that needs to
communicate with the Print / Fax server. Use your favorite editor to add
an entry to the /etc/hosts file containing the IP address and node name of
the device. For example:
192.189.207.3
BRN_310107
The actual format of the entry may vary depending on your system, check your
system documentation and also note the format of other entries in the etc/hosts
file.
The node name in this file does not necessarily need to be the same as the one
that is actually configured into the Brother Print / Fax server (the name that
appears on the printer configuration page), however, it is good practice to make
the names the same. Some operating systems, such as HP/UX, do not accept the
"_" character in the default name, for these systems you must use a different
name).
In any case, the node name in the /etc/hosts file must match the node name in the
/etc/printcap file.
Some systems such as HP/UX and AIX allow you to enter the IP address as the
host name when setting up the print queue. If this is the case, you do not need to
configure the hosts file.
12-3
CHAPTER 12 UNIX PRINTING
2. Choose which Print / Fax server service you want to use. There are
several types of services available on Brother Print / Fax servers. Binary
services pass data through unmodified and are therefore required for
PCL or PostScript rasterized graphics printouts. Text services add a
carriage return at the end of each line for proper formatting of UNIX text
files (which end in linefeed and do not have carriage returns). The text
service can also be used for non-rasterized graphics, such as ASCII
PostScript graphics or many types of PCL graphics.
Choose one of the available services (a service name will be used in step
3):
BINARY_P1
TEXT_P1
Binary data
Text data (CR added)
You may set up multiple print queues on your UNIX host computer for
the same Print / Fax server, each one with a different service name (for
example, one queue for binary graphics jobs and one for text jobs).
3. Configure the /etc/printcap file on each host computer to specify the
local print queue, the Print / Fax server name (also called remote
machine or rm), and the Print / Fax server service name (also called
remote printer, remote queue, or rp), and the spool directory.
This step applies to the majority of UNIX systems, including Linux, Sun OS (but
not Solaris 2.xx), Silicon Graphics (lpr/lpd option required), DEC ULTRIX, DEC
OSF/1, and Digital UNIX. SCO UNIX users should follow these steps, but
should also refer to the SCO UNIX Configuration section. Users of RS/6000 AIX,
HP/UX, Sun Solaris 2.xx, and other systems that do not use the printcap file
should skip to section 3-a. SCO user’s should also skip to section 3a (SCO uses
the printcap file, but this file is automatically configured via the rlpconf
command)
12-4
CHAPTER 12 UNIX PRINTING
An example of a typical printcap file:
laser1|Printer on Floor 1:\
:lp=:\
:rm=BRN_310107:\
:rp=TEXT_P1:\
:sd=/usr/spool/lpd/laser1:
Make sure this information is added to the end of the printcap file. Also make
sure that the last character in the printcap file is a colon ":"
This will create a queue named laser1 on the host computer that communicates to
a Brother Print / Fax server with a node name (rm) of BRN_310107 and a service
name (rp) of TEXT_P1 printing text files to a Brother printer through spool
directory /usr/spool/lpd/laser1. If you are printing binary graphics files,
you would use the service BINARY_P1 instead of TEXT_P1.
The rm and rp options are not available on some UNIX systems, so if necessary
check your documentation (or man pages) to determine the equivalent options.
Users of Berkeley-compatible UNIX systems can use the lpc command to obtain
the printer status:
%lpc status
laser1:
queuing is enabled
printing is enabled
no entries
no daemon present
Users of AT&T-compatible UNIX systems can generally use the lpstat or rlpstat
commands to obtain similar status information. Because this procedure varies
from system to system, refer to your system documentation for the exact usage.
4. Skip this section if you have completed Step 3, unless you have an SCO
UNIX system.
If you have an HP/UX system, IBM RS/6000 AIX computer, or Sun Solaris
2.xx, there is no printcap file. This is also true for some other AT&T-based
UNIX systems, as well as many VMS-based TCP/IP software packages (for
example, UCX, TGV Multinet, etc.). On SCO systems, there is a printcap
file, but it is automatically configured by the rlpconf command. Most of
these systems generally use a printer setup program to define the service
name (remote printer), the Print / Fax server name (remote machine) or IP
address, and the local queue name (spool directory). Refer to the appropriate
section depending on your version of Unix.
12-5
CHAPTER 12 UNIX PRINTING
Linux Configuration
If you do not wish to use the command line interface to configure your Linux
distribution, you may wish to use the Linux Printer System Manager application
on your GUI. To do this, do the following:
1. From the Linux Printer System Manager screen, click the "Add" button.
2. You will now be asked to specify which Printer type you are using,
select the "Remote Unix (lpd) Queue" option and click "OK".
3. You must now specify the remote host name, remote queue name and
the input filter to use.
4. The "Remote Host" name is the IP address of the printer, or the name
from the hosts file which corresponds to the IP address of the printer.
5. The "Remote Queue" name is the service name that the printer will use
when processing the data. Generally we recommend that you use the
name "BINARY_P1", however, if you are planning to send text
documents that do not have a carriage return and a line feed, then use
"TEXT_P1".
6. Select the appropriate "Input Filter" from the list of available printers on
your particular build of Linux.
In order to make your settings work, select the "Restart lpd" option. As soon as
the lpd server restarts, you will be able to send printed documents from your
server.
12-6
CHAPTER 12 UNIX PRINTING
HP/UX Configuration
In the case of HP/UX10.xx, the sam program is used to set up the remote printer.
The steps are as follows:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Execute the sam program. From the list of options, select Printers and
Plotters
Select LP Spooler
Select Printers and Plotters
Select Actions and then Add Remote Printer/Plotter
Enter any name as the Printer Name (this will be the name of the print
queue)
Enter the IP address of the Print / Fax server as the Remote System
Name
Enter the desired Print / Fax server service name as the Remote Printer
Name
Check the box next to Remote Printer is on BSD system
You may accept the default values for the remaining items.
Click OK to configure the printer
You should now be able to print using the lp-d command with the printer name.
If you are using the HP distributed print service, the configuration procedure is
slightly different because you are sending the print jobs to a file server, which in
turn spools the job to the Print / Fax server. You must therefore know the name
of the file server (spooler host) in addition to the above information. You will
add a physical and a remote printer and a remote printer, and then assign a logical
printer to the remote printer (a unique name that does not match any other name).
To print, use the lp -d command with the logical printer name.
Earlier versions of HP/UX use similar procedures to 10.xx users:
1. Enter sam and select Peripheral Devices and then Add Remote Printer
(not Networked printer)
2. Enter the following remote printer settings (the other settings do not
matter):
3. Line printer name (user-selectable)
4. Remote system name (the Print / Fax server name; must match what is in
hosts file or use Print / Fax server IP address)
5. Remote printer queue (Printserver binary or text service name, e.g.
BINARY_P1 or TEXT_P1).
6. Remote Printer is on a BSD System (Yes)
12-7
CHAPTER 12 UNIX PRINTING
IBM RS/6000 AIX Configuration
The RS/6000 AIX operating system uses the smit program to set up the remote
printer. The procedure is as follows for AIX 4.0 and later:
1.
2.
3.
4.
5.
6.
Enter smit and select "devices"
Select "Printer/Plotter"
Select "Print Spooling"
Select "Add a Print Queue"
Select "Remote"
Enter the following Remote Printer Settings:
Name of queue (user selectable)
Host name of Remote Printer (Print / Fax server name; must match name
in /etc/hosts file or use the Print / Fax server IP address)
Name of queue on remote printer (Print / Fax server binary or text
service name, eg. BINARY_P1 or TEXT_P1).
Type of print spooler. BSD (press the LIST button and choose BSD)
The procedure for pre-V4.0 systems is as follows.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Enter smit and select "devices"
Select "printer/plotter"
Select "manage remote printer subsystem"
Select "client services"
Select "remote printer queues"
Select "add a remote queue"
Enter the following remote queue settings:
Name of queue to add (user selectable)
Activate the queue (Yes)
Destination host (Print / Fax server name; must match name in /etc/hosts
file or use the Print / Fax server IP address)
11. Name of queue on remote printer (Print / Fax server binary or text
service name, eg. BINARY_P1 or TEXT_P1).
12. Name of device to add (user selectable; for example lp0)
12-8
CHAPTER 12 UNIX PRINTING
Sun Solaris 2.x Configuration
Sun Solaris 2.x uses the lpsystem and lpadmin programs for remote printer
configuration:
lpsystem -t bsd prnservername
lpadmin -p queue -s prnservername!prnserverservice
accept queue
(not required on newer Solaris
systems)
enable queue
(not required on newer Solaris
systems)
Where queue is the name of the local print queue.
prnservername is the name of the Print / Fax server (must match the entry in
the /etc/hosts file or IP address).
prnserverservice is the Print / Fax server BINARY_P1 or TEXT_P1
service.
If this is the first printer configured, you must also use the lpsched command
prior to the accept command.
As an alternative, you may use Printer Manager in the Admintool utility under
OpenWindows. Select Edit, Add, and Add Access to Remote Printer. Then enter
the Print / Fax server name in the format
prnservername!\prnserverservice as described above. Make sure
that the Printer Server OS is set to BSD (the default setting), and click Add.
Note that we recommend that you use the /etc/hosts file for the printer name
rather than NIS or other name services. Also note that due to a bug in the Sun lpd
implementation on Solaris 2.4 and earlier releases, you may experience problems
printing very long print jobs. If this is the case, a workaround is to use the raw
TCP port software as described later in this chapter.
12-9
CHAPTER 12 UNIX PRINTING
SCO UNIX Configuration
To configure a printer in version Version 5.x of SCO Unix, use the SCOADMIN
program.
1. Select Printers and then Print Manager
2. On the menu select Printer and then Add Remote followed by Unix…
3. Enter the IP address of the Print / Fax server and type in the printer name
to be used to spool to.
4. Deselect "Use External remote Printing Protocol…"
5. Edit the /etc/printcap file to include formfeed add the text rp=lpaf
SCO UNIX requires TCP/IP V1.2 or later to work with Brother Print / Fax
servers. You must first configure the /etc/hosts and /etc/printcap files as
described in step 2. Then run the sysadmsh program as follows:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Select Printers.
Select Configure.
Select Add.
Enter the name of the print queue you entered in the /etc/printcap file as
the Printer name,
Enter anything as the Comment, and Class name.
For the Use printer interface select "Existing".
Press the F3 key to get a list of available interface, and select the desired
one as the Name of interface using the cursor keys ("Dumb" is a good
choice).
Select "Direct" as the Connection.
Enter the desired Device name (/dev/lp generally works).
Select "Hardwired" as the Device.
Select "No" for the Require banner field.
Older SCO Unix Systems
The Brother NC-8100h Print / Fax servers supports the FTP protocol. Earlier
SCO Unix systems are often configured to print using the FTP protocol.
12-10
CHAPTER 12 UNIX PRINTING
DEC TCP/IP Servers for VMS(UCX)
You need to run the sys$system:ucx:$lprsetup command, specify a printer name,
and then enter the Print / Fax server IP address as the remote system name.
Specify one of the Print / Fax server services (see beginning of this section for
options) as the remote system printer name (accept the defaults for other
questions).
TGV's Multinet
TGV's Multinet requires you to run the MULTINET CONFIGURE /PRINTERS
command, then use the ADD command to add a printer, specifying the Print /
Fax server IP address, a protocol type of LPD, and one of the service options
described at the beginning of this section as the remote print queue.
Wollongong's PATHWAY
First make sure that you have the Access option with lpd enabled. Then enter the
Print / Fax server name and IP address in the
TWG$TCP:[NETDIST.ETC]HOSTS file, run the LPGEN program, and execute
the command: add queue/rmachine=prnservername/rprinter=prnserverservice,
where queue is the name of the queue, prnservername is the Print / Fax server
name from the hosts file, and prnserverservice is the Print / Fax server service
name.
IBM/AS4000
To use a Brother Print / Fax server with an IBM AS/400 running IBM’s TCP/IP
gateways services for OS/400 (the OS/400 system must be v3.1 or later)
Use the CFGTCP command at your OS/400 prompt to add the Print / Fax
server’s TCP/IP address to the AS/400 host table.
Use the following one-line OS/400 command to create the LPD queue:
CRTOUTQ OUTQ(<queuename> RMSTSYS
(*INTNETADR) RMTPRTO(<service>)
AUTOSTRWTR(1) CNNTYPE(*IP) DESTTYPE (*OTHER)
MFRTYPMDL (<driver>)
INTNETADR(‘<ipaddress>’) TEXT
(‘<description>’)
where <queuename> is the new AS/400 print queue name, <service> is the Print /
Fax server service name, BINARY_P1 or TEXT_P1, <driver> is the OS/400 printer
driver name (*HP4 is recommended if in doubt), and <ipaddress> is the IP address of
the Print / Fax server.Note that the IP address and description must be enclosed in
single quotes.
12-11
CHAPTER 12 UNIX PRINTING
Other Systems
Other systems use similar programs to set up Print / Fax servers. These programs
will generally ask for the following information:
Requested information:
remote printer
remote host computer name
You should use:
Binary or Text service name
Any name (must match the name in the
printcap file, if any) or in some cases,
you may enter the Print / Fax server IP
address here
IP address of Print / Fax server.
remote host IP address
Technical support specialists for these companies can usually answer
configuration questions if you provide them with the equivalent UNIX
configuration information (tell them that the Print / Fax server looks like a
remote UNIX host computer running the lpd line printer daemon).
If you have not created a spool directory for the Brother Print / Fax server on
your UNIX host computer, you will need to do so now (the printer setup utilities
in HP/UX, AIX, Solaris 2.xx, and other systems will automatically create the
spool directory). The lpd spool directory is usually located in the /usr/spool
directory (check with your system manager to see if the location is different for
your system). To create a new spool directory, use the mkdir command. For
example, to create a spool directory for the queue laser1, you would enter:
mkdir /usr/spool/lpd/laser1
On some systems it is also necessary to start the daemon. This is done on
Berkeley-compatible UNIX systems with the lpc start command as shown in the
following example:
lpc start laser1
12-12
CHAPTER 13 TROUBLESHOOTING
CHAPTER THIRTEEN
13
13
Troubleshooting
Overview
This chapter describes procedures for troubleshooting problems you
may encounter with a Brother Print / Fax server, it is divided into
the following sections:
1.
2.
3.
4.
Installation Problems
Intermittent Problems
Protocol-Specific Troubleshooting
Internet Fax Troubleshooting
13-1
CHAPTER 13 TROUBLESHOOTING
Installation problems
If you cannot print over the network, check the following:
1. Make sure that the printer is powered on, is on-line and ready to print.
Verify that the printer and the configuration are good by printing the
configuration page. Refer to the NC-8100h Quick Network Setup Guide
for information on how to print the configuration page on your Print /
Fax server. If the test fails, check:
a.
If the LED is not blinking after connected to the network, then the
network firmware settings may be corrupted. Please refer to step 3.
b.
In this event, try to restore the factory default settings of the Print /
Fax server by pressing the TEST switch on the back panel of the
printer for longer than 5 seconds. Once you have done that, switch
the printer off and then on again, and try to print out the
configuration page.
2. If the configuration page prints but you cannot print documents, try the
following
If none of the following steps are successful, there is almost
certainly a hardware or network problem!
13-2
CHAPTER 13 TROUBLESHOOTING
a.
If you are using TCP/IP:
Try pinging the Print / Fax server from the host operating system
command prompt with the command:
ping ipaddress
Where ipaddress is the Print / Fax server IP address (note that in
some instances it can take up to two minutes for the Print / Fax
server load its IP address (after setting the IP address). If a
successful response is received, then proceed to the UNIX, TCP/IP
®
®
®
Windows NT /LAN Server, Windows 98/95/Me Peer to Peer
(LPR), Internet Printing or Web Browser troubleshooting section.
Otherwise, proceed to step 3, and then go to TCP/IP Trouble
shooting section.
b.
If you are using Novell system:
Verify that the Print / Fax server can be seen on the network. To do
this, login as the SUPERVISOR (not as someone with supervisor
privileges) or ADMIN (for Netware 4 or later servers), go into
PCONSOLE or NWADMIN, select PRINT / FAX SERVER
INFORMATION, and select the name of the Print / Fax server
(make sure that you have entered the Print / Fax server name). If
you can see Print / Fax server Status and Control in the menu, then
the Brother Print / Fax server is visible to the network, proceed to
the Novel NetWare Installation Troubleshooting Section. Otherwise,
go to step 3.
c.
If you are running Apple Talk for Macintosh:
Make sure that you can see the Print / Fax server name under the
HL-1200/MFL-Pro icon in the Chooser. If it is visible, then the
connection is good, so proceed to the AppleTalk for Macintosh
Section. Otherwise, go to
step 3.
13-3
CHAPTER 13 TROUBLESHOOTING
3. If you cannot make any of the connections in step 2, check the
following:
a.
Make sure the printer is powered on and on-line.
b.
Verify that the cabling, network connection, and print out a
configuration page in the Network STATISTICS information to see
if bytes are being transmitted and received.
Check to see if there is LED activity.
c.
•
•
•
No Light:
If the LED (Link Activity) is off, then the Print / Fax server is not
connected to the network.
Orange: Fast Ethernet
The LED will be Orange if the Print / Fax server is connected to a
100BaseTX Fast Ethernet network.
Green: 10BaseT Ethernet
The LED will be Green if the Print / Fax server is connected to a
10BaseT Ethernet network.
The LED will blink if the Print / Fax server is receiving or
transmitting data.
When the Print / Fax server is receiving packets continuously, the
LED might look ‘off’.
If you are using a repeater or hub, make sure that SQE (heartbeat) is
turned off at the hub (if applicable). Also, if you have a hub or
multi-port repeater, verify that the hub or repeater port is good by
trying the Print / Fax server on a different port or on the other hub or
multi-port repeater.
4. If you have a bridge or router located between the Print / Fax server and
host computer, make sure that the device is set up to allow the Print /
Fax server to send and receive data from the host. For example, a bridge
can be set up to only allow certain types of Ethernet addresses to pass
through (a process known as filtering); therefore, such a bridge must be
configured to allow Brother Print / Fax server addresses. Likewise, a
router can be set up to pass only certain protocols, so be sure that the
desired protocol can be passed through to the Print / Fax server.
13-4
CHAPTER 13 TROUBLESHOOTING
Intermittent Problems
If the Print / Fax server and printer start up OK, but you
intermittently have problems printing, check the following:
1. If you can print small jobs but large graphics jobs are distorted or
incomplete, make sure that you have adequate memory in your printer
and the latest printer driver installed on your computer. The latest
Brother printer drivers can be downloaded from
http://solutions.brother.com.
2. Check the individual protocol troubleshooting sections in this chapter for
additional causes of intermittent printer problems.
13-5
CHAPTER 13 TROUBLESHOOTING
TCP/IP Troubleshooting
If you are using TCP/IP and cannot print to the Print / Fax server
and you have checked the hardware and network as described in the
previous steps, then check the following:
It is always a good idea to try following in order to eliminate the
possibility of Setup errors.
Turning off the printer and then again,
Deleting and recreating the Print / Fax server and creating a new
print queue in order to eliminate the possibility of setup errors.
1. The problem may be the result of mismatched or duplicate IP address.
Verify that the IP address is correctly loaded into the Print / Fax server
(via the configuration page). Make sure that no other nodes on the
network have this address (DUPLICATE IP ADDRESS ARE THE
BIGGEST CAUSE OF TCP/IP PRINTING PROBLEMS).
2. If you used BRCONFIG, NCP or ccr to enter the IP address, make sure
that you exited the remote console properly with a CTRL-D or EXIT and
that you turned the printer off and then again (it may take up to two
minutes for the IP address to take effect).
3. Make sure that the TCP/IP protocol of the Print / Fax server is enabled.
4. If you used rarp, make sure that you started the rarp daemon on any
workstation using the rarpd, rarpd-a, or equivalent command. Verify that
the /etc/ethers file contains the correct Ethernet address and that the Print
/ Fax server name matches the name in the /etc/hosts file.
5. If you used bootp, make sure that you started the bootp daemon on any
UNIX workstation and bootp is enabled (i.e., the "#" is removed from
the bootp entry) in the /etc/bootptab file is correctly configured.
6. Also verify that host computer and the Print / Fax server are either on the
same subnet, otherwise that the router is properly configured to pass data
between the two devices.
13-6
CHAPTER 13 TROUBLESHOOTING
UNIX Troubleshooting
1. Make sure that the /etc/printcap file (if applicable) is typed in correctly.
In particular, look for missing ":" and "\" characters, because a small
error anywhere in the file can have major consequences. Also check the
/usr/spool directory to make sure that you have created a valid spool
directory.
2. If you are using a Linux operating system, the X-Window Print tool
program that is included with Linux may not properly configure the
etc/printcap file for lpd operation, then you might also edit the
etc/printcap file and change the following line in the entry for the printer.
if
:lp = /dev/null: \
then to
:lp = :\
3. If you are using a Berkeley-based UNIX, make sure that the daemon is
started on Berkeley based systems with the command lpc start printer,
where printer is the name of the local print queue.
4. If you are using an AT&T-based UNIX, make sure the printer is enabled
(enable printer, where printer is the name of the local print queue).
5. Make sure that the lpr/lpd remote line printer service are running on the
host computer (refer to your host computer documentation for
information on how to do this).
13-7
CHAPTER 13 TROUBLESHOOTING
6. If you are having trouble printing more than one job at a time, try
increasing the IP timeout using the SET IP TIMEOUT command or
using BRAdmin.
7. If text or PCL jobs are run together, try setting the service (remote
printer) with EOT set to string number 2 (<ESC>E). For example:
SET SERVICE BRN_xxxxxx_P1 EOT 2
8. If the lines of a text file are staggered, make sure that you have specified
a remote printer (rp) name of TEXT in your /etc/printcap file.
9. If you are using Sun Solaris V2.4 or earlier, there is a bug which causes
long print jobs to fail when using a Print / Fax server. If you are having
trouble printing long jobs (over 1MB), add the line mx#0 to your
etc/printcap file entry.
10. If you cannot print from DEC TCP/IP Service for VMS (UCX), make
sure that you have version 2.0B or later of this software, because earlier
versions will not work with Brother Print / Fax servers.
13-8
CHAPTER 13 TROUBLESHOOTING
Windows® NT®/LAN Server (TCP/IP)
Troubleshooting
®
®
If you are having trouble printing with Windows NT or LAN
Server, check the following:
1. Make sure that TCP/IP and TCP/IP print service are installed and
®
®
running on the Windows NT system or the LAN Server file server.
2. If you are using DHCP and you have not created a reservation for the
Print / Fax server, make sure that you enter the NetBIOS name of the
Print / Fax server in the "Name or address of server providing lpd" box.
Windows® 95/98/Me Peer to Peer Print
(LPR) Troubleshooting
®
If you are having trouble printing on a Windows 95/98/Me Peer-toPeer network (LPR method), check the following:
1. Make sure that the Brother LPR Port driver is correctly installed and
®
configured according to the Windows 95/98/Me Peer-to-Peer chapter 7.
You may find that during the installation of BLP software, the
screen that prompts you for a Port name is not displayed. This may
®
happen on some Windows 95/98/Me computers. Press the ALT and
TAB keys to make it appear.
13-9
CHAPTER 13 TROUBLESHOOTING
Windows® 95/98/Me Peer-to-Peer (HP
JetAdmin compatible method)
Troubleshooting
®
If you are having trouble printing on a Windows 95/98/Me Peer-toPeer network, check the following (HP JetAdmin compatible
method):
1. If the Print / Fax server does not show up under JetAdmin on a
®
Windows 95/98/Me Peer-to-Peer network, try removing all of the
®
Windows 95/98/Me network software from the Network Control panel
and then reinstalling them as follows:
First install the IPX/SPX-Compatible Protocol (or the TCP/IP
protocol if you are using a later version of JetAdmin), the Client for
Microsoft Networks, and the network adapter card driver.
Install the Latest HP JetAdmin software
Restart the system, and then add the HP JetAdmin service.
Windows® 95/98/Me/NT® 4.0 Peer-to-Peer
Print (NetBIOS) Troubleshooting
®
®
If you are having trouble printing on a Windows 95/98/Me/NT 4.0
(or later) Peer-to-Peer network (NetBIOS), check the following:
1. Make sure that the Brother NetBIOS Port driver is securely installed and
®
®
configured according to the Windows 95/98/Me/NT 4.0 Peer-to-Peer
(NetBIOS) chapter 7. You may find that during the installation of the
port driver, the screen that prompts you for a Port name is not displayed.
®
®
This happens on some Windows 95/98/Me/NT 4.0 computers. Press
the ALT and TAB keys to make it appear.
2. Make sure that the Print / Fax server is configured to be in the same
workgroup or domain as the rest of your computers. It may take several
minutes for the Print / Fax server to appear in the network neighborhood.
13-10
CHAPTER 13 TROUBLESHOOTING
Brother Internet Print (TCP/IP)
Troubleshooting
1. The first step in troubleshooting is to make sure that you have a valid Email connection on both the sending PC and the receiving Print / Fax
server. Try sending an E-mail message from the PC to a user at the
remote site who can receive mail via the POP3 server. If this does not
work, there may be an E-mail configuration problem on the PC, on the
local E-mail server, or on the remote POP3 server. Double check to
make sure that the E-mail parameters that you configured on the PC and
on the remote Print / Fax server match those that are configured on the
E-mail servers.
2. If you can print small files OK but are having problems printing large
files, the problem may be in the e-mail system! Some E-mail systems
have difficulties printing large files. If the file does not reach its
destination intact, then the problem is with the E-mail system.
3. You can also enable the partial e-mail print facility on your client PC,
this will split the e-mail up into fragments which should then not
overwhelm your e-mail server. To do this, select the property dialog of
the Brother Internet Print Port.
13-11
CHAPTER 13 TROUBLESHOOTING
Windows® 95/98/Me/2000/XP FTP/IPP
Troubleshooting
Want to use a different Port number other than 631
If you are using Port 631 for IPP printing, you may find that your
firewall may not let the print data through. If this is the case, use a
different port number (port 80), or configure your Firewall to allow
Port 631 data through.
To send a print job using IPP to a printer using Port 80 (the standard
®
HTTP port) enter the following when configuring your Windows
2000/XP system.
http://ip_address/ipp
®
Get More Info option in Windows 2000/XP not working
If you are using a URL of:
http://ip_address:631 or
http://ip_address:631/ipp, the “Get More Info” option
®
in Windows 2000 will not function. If you wish to use the “Get
More Info” option use the following URL:
http://ip_address
®
This will then force Windows 2000 to use Port 80 to communicate
with the Brother Print / Fax server.
®
Windows 95/98/Me clients not able to get the driver from a
®
Windows 2000/XP system.
You must be using version 4.0 or later of Internet Explorer and the
“Microsoft Internet Print Services” software must be installed on
your client computers.
13-12
CHAPTER 13 TROUBLESHOOTING
Novell NetWare Troubleshooting
If you cannot print from NetWare and you have checked the
hardware and network as described in the previous steps, first verify
that the Brother Print / Fax server is attached to the server queue by
going to PCONSOLE, selecting PRINT QUEUE INFORMATION,
and then CURRENTLY ATTACHED SERVERS. If the Print / Fax
server does not appear in the list of attached servers, then check the
following:
It is always a good idea to try followings in order to eliminate the
possibility of setup errors
Turning off the printer and then on again to force to rescan the
Netware queue.
Deleting and recreating the Print / Fax server and creating a new
print queue in order to eliminate the possibility of setup errors.
1. If you changed the login password, you must change the password in
both the Brother Print / Fax server (using the SET NETWARE
PASSWORD command if you are using the BRConfig software) or by
using a web browser or the BRAdmin application and in the file server
(using the PCONSOLE Print / Fax server Information Change Password
command).
2. If you created the print queue using PCONSOLE and instead of
BRAdmin, make sure that you have enabled at least one NetWare file
server using the SET NETWARE SERVER servername ENABLED
command.
3. Have you exceeded your NetWare user limit?
4. Make sure that the Print / Fax server name you used in PCONSOLE
exactly matches the name that is configured in the Print / Fax server, and
make sure it is defined as a Queue Server for the print queue.
5. If you are running both 802.3 and Ethernet II frames on different file
servers on your network, there is a possibility that the Print / Fax server
may not make a connection to the desired file server. Try forcing the
frame type to the desired one using the SET NETWARE FRAME
command from the Print / Fax server remote console or using BRAdmin.
6. If you are using DOS CAPTURE statement and losing portions of your
print job, try setting the TIMEOUT parameter in your CAPTURE
®
statement to a higher value (at least 50 seconds for Windows ).
13-13
CHAPTER 13 TROUBLESHOOTING
AppleTalk Troubleshooting
If you cannot print from an AppleTalk for Macintosh computer and
you have checked the hardware and network as described in the
previous steps, then check the following:
1. Make sure that you are running Phase 2 AppleTalk and that you have
selected the correct network interface from the AppleTalk Control Panel
on the Macintosh.
2. Make sure that the AppleTalk protocol of the Print / Fax server is
enabled.
3. Verify that you have selected the correct AppleTalk zone. Because the
Print / Fax server gets its zone information from router broadcasts, it
may not be in the zone you expect, and will therefore not show up in the
Chooser. If this is the case, you may need to force the zone name using
a web browser or the SET APPLETALK ZONE command from
TELNET.
13-14
CHAPTER 13 TROUBLESHOOTING
DLC/LLC Troubleshooting
If you are having trouble printing with DLC/LLC, check the
following:
1. Make sure that the DLC/LLC protocol is enabled using either BRAdmin,
a web browser or TELNET.
®
2. Make sure that the MAC address of the Windows setting is as same as
the print configuration page result.
Web Browser Troubleshooting (TCP/IP)
1. If you can not connect to the Print / Fax server using your web browser
it may be worth checking the Proxy Settings of your browser. Look in
the Exceptions setting and if necessary, type in the IP address of the
Print / Fax server. This will stop your PC from trying to connect to your
ISP or proxy server every time you wish to look at the printer server.
2. Make sure that you are using the proper Web Browser, we recommend
Netscape Navigator version 4.xx or later/ Microsoft Internet Explorer
version 4.xx or later.
13-15
CHAPTER 13 TROUBLESHOOTING
Internet Fax Troubleshooting
1. If there is a mail delivery error while sending an Internet Fax, the mail
server will send an error message back to the FAX/MFC and the error
message will be printed. If there is an error while receiving mail, an error
message is printed (Ex. The message being sent to the FAX/MFC was
not in a TIFF-F format.) All documents transmitted to the FAX/MFC via
E-mail must be in a TIFF-F format.
2. If an error message is printed while receiving E-mail text from a PC
“ATTACHED FILE FORMAT NOT SUPPORTED” the senders mail
application may not be set for a “Plain Text” format or “Vcard” the
virtual business card feature may be set to ON
3. If the receiver’s mail system is not compatible with the MIME format,
you cannot transmit a document to the receiver. Depending on the
receiver’s server, there are some cases that the error mail will not be sent
back.
4. Messages cannot be received in an HTML format. This format is not
supported. All messages must be received in a TIFF-F Format.
5. If the size of a documents image data is huge, there is a possibility of
unsuccessful transmission if the system administrator has imposed a
limit on the maximum size of E-mails and their attachments. The
document you are sending should be separated into smaller documents
that will be accepted by the mail server. (Ex. A 42 page document of the
CCITT#1 test chart is approximately 1Mbyte in size).
6. If you do not receive E-mail, check the Auto Polling setting and Polling
frequency.
7. If you cannot retrieve mail from the mail server, check the settings for
the POP3 server and Mailbox name. Check that the POP3 password is
entered correctly. This setting is case sensitive.
8. If Relay Broadcast is not forwarding E-mail to a G3 Fax, check the
Relay Broadcast settings and Relay Domain registration. A Relay
Domain must be entered for this function to work.
9. The Relay Broadcasting and Broadcasting features cannot be used at the
same time.
10. Relay Broadcast can support the relay of a document up to a maximum
of 48 Fax machines through conventional telephone lines. If sending to
more than 48 locations the sender must divide the transmission locations
into 48 locations or less for each relay broadcast.
11. When receiving E-mail messages from the POP server, the FAX/MFC
can receive a maximum of 32 mail messages. If there are more than 32
mail messages in the POP server, the FAX/MFC will receive a
maximum of 32 mail massages and then receive the remaining after the
next polling interval.
12. The NC-8100h Print / Fax Server requires a portion of the user memory
for operation. With the NC-8100h installed the number of Fax sheets
that can be sent or received will be reduced (by approximately 30 pages
of the brother No1 Test Chart) from the standard FAX/MFC capacity.
13-16
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
141
CHAPTER FOURTEEN
14
Brother Network PC Fax
Software
Installing and using the Brother
Network PC Fax Software
Overview
Important Information:
Please check Brother
Solutions centre for the
latest updates available for
Brother Network PC Fax.
Visit
http://solutions.brother.com/
The Brother NETWORK PC FAX feature allows you to use your PC to send
any application or document file as a standard fax. You can create a file in
any application on your PC, and then send it as a NETWORK PC FAX. You
can even attach a cover page note. All you have to do is set up the receiving
parties as Members or Groups in your PC FAX Address Book or simply enter
the destination address or fax number into the User Interface. You can use the
Address Book Search feature to quickly find members to send your fax.
Quick Tips:
Please refer to the “Important Information” sections before using Brother
Network PC Fax.
1. Ensure that Network PC Fax is set to “Enable” in the Sending tab of Setup.
2. To send an E-mail from Brother Network PC Fax you can either enter the
E-mail address in the To: field or in the display for Facsimile Style using the
PC keyboard or select the member from the Address Book. The member
must have E-mail selected as the chosen destination for that member.
3. To send an Internet Fax from Brother Network PC Fax you can either enter
the Internet Fax address in the To: field or in the display for Facsimile style
using the PC keyboard or select the member from the Address Book. The
member must have FAX/MFC Mail Address selected as the chosen
destination for that member.
4. To send a Network Fax simply select a member from the address book or
enter the fax number into the User Interface with the PC keyboard. The
member must have Fax selected as the chosen destination for that member.
14-1
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
Installing Network PC Fax
Important Information:
If the installer screen does
not appear automatically
select Start | Run and type
X:/setup.exe
(X:/ should be the drive
letter of your CD ROM
drive on your PC).
Insert the CDROM supplied with your Brother FAX/MFC, the installer
screen will automatically start. From the installer screen select your model
and language (if these options are present), then select Network Applications
for (optional NC-8100h Print / Fax Server), then select Brother PC Fax and
follow the screen prompts. When prompted reboot your PC.
It is now necessary to install the Brother Network Print Software from the
CDROM so you need to reinsert the CDROM. Select Network Applications
for (optional NC-8100h Print / Fax Server), then select Network Print
Software. Follow the screen prompts, you will prompted for the IP address of
the NC-8100h. If in any doubt contact your Network Administrator.
Note: If you have already installed the FAX/MFC as a network printer you
may have already installed the Brother Network Print Software.
To check select Start | Settings | Printers
Highlight the Brother PC Fax driver from the list and right click the mouse
button and select properties then select the details tab.
Select the “Print to Following Port” as illustrated above, if Brother LPR Port
is listed for your FAX/MFC you can just specify for Brother Network Fax to
use this previously installed port. If you have multiple Brother LPR ports
please ensure that you select the correct port address. If in any doubt please
contact your Network Administrator.
14-2
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
Setting Up User Information
1. Access the User Information from the FAX Sending dialog box by
clicking
OR—From the Start menu, select Program File, Brother, Brother
MFL Pro, and then select PC-FAX Setting.
The Brother PC Fax Setup dialog box will appear:
2. Enter the required User information. This information is required to
create the Fax Header and Cover Page.
3. To save the User Information, click OK.
14-3
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
Setting Up Sending Information
Brother Network PC Fax can be configured through the Sending tab.
Important Information
Please ensure that Network
Fax is “Enabled”.
This software can be used in a network environment and with a locally
connected machine. It is important that when used in a network environment
the Network PC Fax is set to enable.
The include header option sends an additional page of information along
with fax or E-mail data which contains user and subject information.
If the Network PC Fax is being used, a private telephone exchange system
and an outside line access number is needed this can be pre programmed in
the Dial Settings on the Sending Information page.
The user has the choice of two interfaces. To change the user interface
change the interface setting above.
Facsimile Style
Simple Style
14-4
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
Setting Up Speed Dial
Access the Speed Dial tab from the Brother PC-FAX Setup dialog box by
clicking the Speed Dial tab. (To use the feature you must select the
Facsimile Style user interface.) You can register any address or group on one
of the ten Speed Dial buttons.
To register an address on a Speed Dial location:
1. Click the Speed Dial location you want to program.
2. Click the address or group you wish to assign to the Speed Dial location.
3. Click the Add>> button to program the Speed Dial location.
To clear a Speed Dial location:
1. Click the Speed Dial location you want to clear.
2. Click the Clear button.
14-5
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
The Address Book
From the Start menu, select Program File, Brother, Brother MFL Pro, and
then click Address Book. The Brother Address Book dialog box will appear:
Setting Up a Member in the Address Book
In the Brother Address Book dialog box you can add, edit and delete stored
information for members and groups.
icon to add a member.
1. In the Address Book dialog box, click the
The Brother Address Book Member Setup dialog box will appear:
Important Information:
When creating the Address
Book member please select
the method of default
delivery.
2. In the Brother Address Book Member Setup dialog box, type the member’s
information.
Name and Fax are required fields. You can also enter the an E-mail contact
address and FAX/MFC address for the address book member Click the OK
button to save the member’s information.
14-6
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
Setting Up a Group for Broadcasting
If you repeatedly send the same PC-FAX to multiple recipients, you can
combine members into a Group.
1. In the Brother Address Book dialog box, click the “New Group” button to
create a group.
2. The Brother Address Book Group Setup dialog box appears:
3. Type the name of the new group in the Group Name field.
4. In the Available Names box, select each member to be included in the
Group, and then click Add>>.
5. Members you add to the group will be listed in the Group Members box.
6. After all the members have been added, click OK.
14-7
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
Editing Member Information
To edit a Member or Group:
1. Select the Member or Group you want to edit.
2. Click the
Edit icon.
3. Edit the Member or Group information.
4. Click OK to save your changes.
Deleting a Member or Group
To delete a Member or Group:
1. Select the Member of Group you want to delete.
2. Click the
Delete icon.
3. Click OK when the Delete OK? dialog appears.
Exporting the Address Book
You can export the address book to an ASCII text file (*.csv).
To export the current telephone book:
1. From the Address Book select File, point to Export, and then click Text—
OR—Click Vcard and go to Step 5.
2. Select the data fields you wish to Export from the Available Items column,
and then click Add>>.
3. If you are exporting to an ASCII file, select Divide Character - Tab or
Comma. This selection inserts a Tab or Comma between each data field
when it is Exported.
4. Select the OK button to save the data.
5. Type in the name of the file, and then select Save.
6. If you are creating a Vcard, you must first select the member.
7. Select items in the order you want them listed.
14-8
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
Sending a File as a PC FAX Using the
Simple Style
1. Create a file in Word, Excel, Paint, Draw, or any other application on your
PC.
2. From the File menu, select Print.
3. The Print dialog box will appear:
4. Select Brother PC-FAX as your printer, and then click OK.
5. The FAX Sending dialog box will appear:
6. In the To: field, type the fax number of the receiving party. By click To:
button, you can also use the Address Book to select destination fax numbers.
If you made a mistake entering a number, click the Clear button to clear all
entries.
7.
To send a Cover Page and note, click the Cover page On check box.
8. When you are ready to send your fax, click the Send
9. If you wish to cancel the fax, click the
14-9
icon.
icon.
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
Sending a File as a PC FAX using the
Facsimile Style
1. Create a file in Word, Excel, Paint, Draw, or any other application on your
PC.
2. From the File menu, select Print.
The Print dialog box will appear:
3. Select Brother PC-FAX as your printer, and then click OK.
The FAX Sending dialog box will appear:
4. Enter a telephone number by using any of the following methods:
a. Enter the number using the numeric keypad.
b. Click any of the 10 Speed Dial buttons.
c. Click the Address Book button, and then select a Member or Group
from the Address Book.
If you make a mistake you can use the Clear button to clear all the entries.
5. To include a cover page, check the Cover Page On. You can also click the
icon to create or edit an existing cover page.
6. Click Start to send the fax.
7. If you wish to cancel the fax, click Stop.
Redial:
If you wish to redial a number, press Redial to scroll through the last five fax
numbers.
14-10
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
Updating other FAX/MFC’s through the
Network
It is possible to program Brother FAX/MFC’s on the network with either
settings from an already programmed FAX/MFC or with data from the
Brother Network PC Fax Address Book.
When Brother Network PC Fax in used from a PC that has BRAdmin
Professional installed, an extra option appears in BRAdmin. By selecting a
networked FAX/MFC in the BRAdmin main window and right clicking it
you will be presented with an extra option, Configure Address Book.
When you select this option BRAdmin reads the telephone settings from that
machine (if there are any programmed) into Brother PC Fax Address Book.
Illustrated below is the Brother Address Book, on the left are One Touch /
Speed Dial numbers read from the machine. On the right is the Brother
Address Book. It is now possible to allocate One Touch / Speed Dial
numbers from the FAX/MFC into the Brother Address Book and also use
members of the Brother Address Book and send them to the FAX/MFC. You
can now make changes to the data in the Brother Network PC Fax Address
Book and click OK.
14-11
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
This data is then stored in the Windows Temp Folder and can be used to
update singular or multiple FAX/MFC’s on the network.
Highlight singular or multiple networked Brother FAX/MFC’s in the main
BRAdmin window by highlighting and pressing the shift key on your
keyboard. Right click the highlighted FAX/MFC’s and press Send Address
Book Data. The new data is then sent to all the highlighted FAX/MFC’s.
A dialogue box is displayed showing the upload status of current FAX/MFC
and beneath this the whole progress is displayed if updating multiple
FAX/MFC’s.
14-12
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
When the process is finished a dialogue box is displayed showing which
FAX/MFC’s on the network have been updated.
Sending a Fax from Your Macintosh®
Application
You can send a fax directly from your Macintosh application using the
following steps:
1. From the Apple menu, open the Chooser.
2. Click HL-1200/MFL Pro icon. On the right side of the Chooser, click the printer to
®
which you want to print. Close the Chooser.
3. To begin the fax transmission, select Print from the File menu.
The Printer dialog box appears:
When Printer is selected, the top button shows Print and the Address
button is grayed.
®
®
To connect with AppleTalk , it is necessary to show printer’s AppleTalk
service name in the Connect to list box. The default node name will be
BRN_XXXXXX_P1, where “XXXXXX” is the last six digits of the Ethernet
address (MAC address).
You can find the node name and MAC address by printing out the
FAX/MFC configuration page. Refer to the NC-8100h Quick Setup Guide
for information on how to print the configuration page on your Print/Fax
server.
4. From the Output pop-up menu, select Facsimile.
When Facsimile is selected, the top button shows Send Fax and the Address
button is available.
5. Click Send Fax.
The Send Fax dialog box appears:
The Send Fax dialog box has two list boxes. The left box shows all the
previously Stored Fax Numbers; the right box will show the Destination
Fax Numbers as you select them.
6. To address the fax, type a fax number in the Input Fax Number box.
—OR—
Select a name/number from the Stored Fax Numbers box, and then click
>>. Your recipient will appear in the Destination Fax Numbers box.
Note: You can select several stored numbers at once by using the Shift and
Ctrl keys.
14-13
CHAPTER 14 BROTHER NETWORK PC FAX SOFTWARE
7. If you want to, you can add your new recipients to the Stored Fax Number at
this time by clicking New.
—OR—
You can add a new group by clicking Group.
8. If you are finished addressing your fax, click Send Fax.
Click OK to return to the Send Fax dialog box.
To select and send only certain pages of the document, enter the page numbers in
the From and To : boxes in the Facsimile dialog box.
If you click Send Fax without addressing your fax, the following error message
appears:
Setting Up Your Address Book
You can add new members and groups to your Address Book, even while you are
addressing a fax.
Adding a New Member
1. To add a new member to the Address Book, in the Facsimile dialog box clic
Address.
The Address Book dialog box appears:
2. Click New. The following dialog box appears:
3. Type the name and fax number.
4. If you want to, you can store a comment in the Memo field if you wish (up to
15 characters).
5. Click OK to return to the Address Book dialog box.
Adding a New Group
You can set up a group of multiple recipients.
1. Click Group.
The Group Setting dialog box appears.
2. In the Group Name field, type a name for your Group.
3. From the Stored Fax Numbers box select the recipients for your Group, and
then click.
Your selection will appear in the box under the Group Name field.
4. Click OK.
The Address Book dialog box reappears:
5. Click OK.
The Print/Facsimile dialog box reappears:
6. If you are ready to send your fax, click Send Fax.
14-14
CHAPTER 15 Brother BFP Software
151
CHAPTER FIFTEEN
15
Brother BFP Software
Brother Internet Fax Printing
Software
Overview
Depending on your network configuration and application requirements for
sending faxes via a network, you can choose between Brother Network PC FAX
Software or Brother Internet Fax Printing Software. With either software,
viewable document such as web pages, word documents, PDF documents can be
sent from the users desktop to any standard Facsimile machines, Internet fax
machines and E-mail addresses.
®
Brother Internet Fax Printing Software (BFP) is a Windows 95/98/Me,
®
®
®
Windows NT and Windows 2000/XP *1 software utility that gives network PC
Fax and Internet Fax functionality from the desktop to users on your network or
over the Internet.
BFP utilizes SMTP as the transport for sending documents from your PC. This
allows any PC supported by a SMTP mail server to send an Internet FAX even if
that PC does not have direct access to the networked FAX/MFC.
Brother Network PC Fax Software utilizes LPR as the transport for sending
documents from your PC to the networked FAX/MFC for transmission. This
requires that the sending PC has access to the network that the sending
FAX/MFC is connected.
®
*1 Windows® XP users must download the Windows XP version of the BFP Software. Please check
http://solutions.brother.com for availability and download information.
WWW
Figure 1 Brother Internet Fax Printing Overview
15-1
CHAPTER 15 Brother BFP Software
Installing Brother Internet Fax Printing
Driver
Important Information:
If the installer screen
does not appear
automatically select Start
| Run and type
X:/setp.exe
(X:/ should be the drive
letter of your CD ROM
drive on your PC)
Insert the CDROM supplied with your Brother FAX/MFC into your CD-ROM
Drive. The installer screen will automatically start.
1. Select Install Software.
2. Select Network Applications for Optional NC-8100h.
3. Highlight Brother Internet Fax Printing (BFP) Driver.
4. Click Install.
Next you will be presented with the licensing agreement, please carefully read
the agreement and make the necessary choice.
The next step requires you to specify the location you wish to install the BFP
files. Brother suggests you accept the default.
Figure 2 Default path for installation files
15-2
CHAPTER 15 Brother BFP Software
When Installing BFP
®
on Windows NT4.0
and 2000 operating
systems we
recommend that you
add a “:” to the end
of the port name so
BFP1 = BFP1:
During the installation you are presented with the following screen, select the default
unless you have previously installed this software. If this is the case use a port
number that has not been previously configured. Example BFP2
Figure 3 BFP Port Number
You also need to enter certain information into the printer driver dialog screen as
illustrated below.
Here you can enter the
default E-mail address
NC-8100h or you can
leave it blank.
*If an address is
specified here this will
always be used as default
sending address.
This can be the host
name or IP address of
the E-mail server
Figure 4 Port Settings
It is very important that you enter your own E-mail address. You also need to
configure the SMTP mail server IP address or host name as illustrated above.
If in any doubt contact your Network Administrator for assistance
15-3
CHAPTER 15 Brother BFP Software
Changing the BFP Port Settings
If you have more than one networked FAX/MFC with an NC-8000 or NC-8100h
Print/Fax Server you may want to change the settings of the BFP software to use an
alternative machine as the network fax print server.
To alter BFP settings, select Start | Settings | Printers to open the Printers dialogue
®
box. From the Printers Windows illustrated below highlight the Brother Internet Fax
driver and right click the mouse. From the list presented select Properties.
Figure 5 BFP Settings
You are now presented with the screen below, which allows you to configure the
BFP settings. To change the details of the print server that receives the fax for
onward sending select the details tab.
Figure 6 Brother Internet Fax Printer Driver
Below is shown the current configuration to alter this press the Port Settings key.
15-4
CHAPTER 15 Brother BFP Software
Use the port
settings button to
alter BFP
configuration
Figure 7 Brother Internet Fax Driver Settings
From the Port Settings dialogue box you can change the settings.
Figure 8 BFP Port settings
15-5
CHAPTER 15 Brother BFP Software
Relay Broadcast Function
“Important Information”
Before you can successfully use the NC-8000 or NC-8100h as a network fax solution
you need to switch the feature “Relay Broadcasting” ON at the FAX/MFC. In
addition you also need to set a “Trusted Domain” at the FAX/MFC.
The easiest way to achieve this is to logon to the machine using Web Based
Management. Open you favourite web browser and enter the IP address of the
network FAX/MFC. Enter the password of the NC-8000 or NC-8100h Print/Fax
Server to access the configuration settings.
If you do not know the password contact you Network Administrator.
Then browse to Internet Settings and Relay Function.
In order for the FAX/MFC to receive data from the desktop and then send this
information (network fax) to other fax machines the “Relay Broadcast Function”
must be switched “ON”. Also you must tell the networked FAX/MFC which
networks can relay faxes through your machine. This is known as setting the
“Trusted Domain”. For instance, if a network FAX/MFC has an E-mail address of
fax@brother.com and users of this machine also have E-mail addresses with the same
domain name then the FAX/MFC must be told to allow these users to send network
faxes through the machine. This is known as the “Relay Function” and “Trusted
Domains”. So we set the trusted domain as brother.com
“Trusted Domains” Provide security for your machine. In that only users from a
particular domain can send faxes through your network connected FAX/MFC.
“Trusted Domains”
Provide security for
your machine. In that
only users from a
particular domain can
send faxes through
your network
connected FAX/MFC.
15-6
CHAPTER 15 Brother BFP Software
Uninstalling from Windows
95/98/Me/NT 4.0/2000
®
®
Select Start | Settings | Control Panel and then double click the Add/Remove
programs icon. From the list of installed programs select the Brother Internet Fax
Vx.xx as shown below then click the Add/Remove button.
®
®
In the case of Windows NT 4.0/2000 you also need to remove the Brother Internet
Fax Driver from the Add/Remove Program Properties.
Figure 9 Add /Remove programs
15-7
CHAPTER 15 Brother BFP Software
In addition to this you also need to manually remove the Brother Internet Fax Driver
from the printers list.
To do this select Start | Settings | Printers you are then presented with the Window
illustrated below.
Figure 10 Remove the Brother Internet Fax Driver
Right click the Brother Internet Fax Driver, from the list click delete. Accept the
confirmation and the driver will be deleted.
15-8
CHAPTER 15 Brother BFP Software
Using the BFP Address Book
This utility can administer the Fax addresses, Internet Fax addresses and E-mail
address of all the contacts that you wish to use with the BFP Software.
Additionally you can create Groups of contacts that you may wish to broadcast
documents to.
From the Start menu, select Program File, Brother, Brother MFL Pro, and then
click Address Book. The Brother Address Book dialog box will appear:
Figure 11 Brother Address Book
Setting Up a Member in the Address Book
In the Brother Address Book dialog box you can add, edit and delete stored
information for members and groups.
icon to add a member.
1. In the Address Book dialog box, click the
The Brother Address Book Member Setup dialog box will appear:
15-9
CHAPTER 15 Brother BFP Software
Important Information:
When creating the Address
Book member please select
the method of default
delivery.
Figure 12 Brother Address Book Member Setup
2. In the Brother Address Book Member Setup dialog box, type the
member’s information.
Name and Fax are required fields. You can also enter the an E-mail contact
address and FAX/MFC address for the address book member Click the OK
button to save the member’s information.
15-10
CHAPTER 15 Brother BFP Software
Setting Up a Group for Broadcasting
If you repeatedly send the same PC-FAX to multiple recipients, you can combine
members into a Group.
1. In the Brother Address Book dialog box, click the “New Group” button
to create a group.
Figure 13,14 Brother Address Book
2. The Brother Address Book Group Setup dialog box appears:
Figure 15 Brother Address Book Group Setup
3. Type the name of the new group in the Group Name field.
4. In the Available Names box, select each member to be included in the
Group, and then click Add>>.
5. Members you add to the group will be listed in the Group Members
box.
6. After all the members have been added, click OK.
15-11
CHAPTER 15 Brother BFP Software
Editing Member Information
To edit a Member or Group:
1. Select the Member or Group you want to edit.
2. Click the
Edit icon.
3. Edit the Member or Group information.
4. Click OK to save your changes.
Deleting a Member or Group
To delete a Member or Group:
1. Select the Member of Group you want to delete.
2. Click the
Delete icon.
3. Click OK when the Delete OK? dialog appears.
Exporting the Address Book
You can export the address book to an ASCII text file (*.csv).
To export the current telephone book:
1. From the Address Book select File, point to Export, and then click
Text—OR—Click Vcard and go to Step 5.
2. Select the data fields you wish to Export from the Available Items
column, and then click Add>>.
3. If you are exporting to an ASCII file, select Divide Character - Tab or
Comma. This selection inserts a Tab or Comma between each data field
when it is Exported.
4. Select the OK button to save the data.
5. Type in the name of the file, and then select Save.
6. If you are creating a Vcard, you must first select the member.
7. Select items in the order you want them listed.
15-12
CHAPTER 15 Brother BFP Software
Sending a Network Fax with BFP
From the application you wish to send the document from select File | Print.
Ensure that the Brother Internet Fax Driver is selected as shown below.
Figure 16 Brother Internet Fax driver
Clicking OK with start the BFP dialogue box as illustrated below. From this dialogue
box you can either specify an address in the address line or select a location from the
address book. If you wish to type more than one location in the address line make
sure they are separated by “;”.
Figure 17 The BFP Send Dialogue Box
Please Note: When entering a Fax Contact you must first specify the Internet
Address of the machine that will send the document followed by the fax number
as shown below.
Mailmfc9650@brother.co.uk(fax#2537)
15-13
APPENDIX
A
A
Appendix A
A
Appendix
General Information
You can change the configuration of your Print / Fax server
using any of the following methods.
•
•
•
•
•
®
Brother BRAdmin application for Windows
®
95/98/Me/NT 4.0/2000/XP
HTTP (using a web browser)
WebJetAdmin Software
TELNET (command utility)
Brother BRCONFIG NetWare Utility (command utility)
BRAdmin (Recommended)
The Brother BRAdmin application can use the TCP/IP or
IPX/SPX protocol. This utility allows you to graphically
manage aspects of the network and printer. It can also be used to
upgrade the firmware of the Print / Fax server.
HTTP (Recommended)
Use your favorite web browser to connect to the Brother Print /
Fax server. This will allow you to configure the MFC and/or
Print / Fax server parameters.
WebJetAdmin
Brother’s Print / Fax server range is HP WebJetAdmin
compatible.
A-1
APPENDIX
TELNET
To connect to the Print / Fax server using TELNET on UNIX,
®
®
Windows NT , or most other TCP/IP systems, type: TELNET
IP address at the command prompt of the system prompt, where
ipaddress is the IP address of the Print / Fax server. When you
are connected, push RETURN or ENTER to get the "#" prompt,
enter the password "access" (the password will not appear on
the screen), and type anything in response to the Enter
Username> prompt. When you see the Local> prompt, you are
ready to enter commands.
Enter HELP at the command prompt for a list of supported
commands.
BRCONFIG
Brother BRCONFIG utility runs on the DOS system prompt and
is installed with BRAdmin. To connect the Print / Fax server
using the Brother BRCONFIG NetWare utility, Choose the
BRCONFIG utility from the Brother BRAdmin utilities. If you
have only one Print / Fax server, you will be immediately
connected to that server. If you have more than one Print / Fax
server, you will be given a list of available Print / Fax servers.
Type the number of the Print / Fax server to which you wish to
connect. When you are connected, enter the password "access"
(the password will not appear on the screen) at the "#" prompt,
and type anything in response to the Enter Username> prompt.
When you get the Local> prompt, you are ready to enter
commands. To use BRCONFIG, a Novell Server (running the
IPX protocol) is necessary and an active connection must be
made to the server.
Enter HELP at the command prompt for a list of supported
commands.
A-2
APPENDIX
B
Appendix B
B
Using Services
General
A service is a resource that can be accessed by computers that wish to print to the
Brother Print / Fax server. The Brother Print / Fax server provides the following
predefined services (do a SHOW SERVICE command in the Brother Print / Fax
server remote console to see a list of available services):
Service (Example)
BINARY_P1
TEXT_P1
POSTSCRIPT_P1
PCL_P1
BRN_xxxxxx_P1_AT
BRN_xxxxxx_P1
Definition
TCP/IP binary service
TCP/IP text service (adds carriage return after
each line feed).
PostScript service (switches PJL-compatible
printer to PostScript mode)
PCL service (switches PJL-compatible printer
to PCL mode)
AppleTalk with Quickdraw Driver for Mac OS
8.6 – 9.1
NetWare service and NetBIOS service
(TCP/IP is enabled for backwards
compatibility)
where "xxxxxx" is the last six digits of the Ethernet address (for example,
BRN_310107_P1).
A-3
APPENDIX
C
Appendix C
C
Reloading the Print / Fax
Server Firmware
General
The firmware on the Print / Fax server is stored in flash memory. This means that
you can upgrade the firmware by downloading the appropriate update file. To get
the latest firmware update, access the Brother Solutions web site at
http://solutions.brother.com/
The Print / Fax server supports multiple MFC models so when inserted into the
MFC the version of the NC-8100h hardware is checked against the firmware of
your machine. If the firmware for your NC-8100h has been superseded with a
later version of firmware for your model a message is displayed on the LCD.
“Please update your firmware”.
Some firmware versions that we provide will automatically factory reset your
Print / Fax server parameters. We try to avoid doing this, however, if we add a
significant new feature to our Print / Fax server, it can result in the Print / Fax
server being factory reset.
Because of this, we STRONGLY recommend that you make a note of the current
Print / Fax server configuration before you upgrade. To do this, Print out a
configuration page by referring to the Quick Setup Guide that was supplied with
the NC-8100h for details on how to print a configuration page.
There are three methods of upgrading the firmware in your Brother Print / Fax
server:
1. Use the BRAdmin application (Recommended)
2. Use the FTP protocol (Recommended if running on Macintosh or
Unix network)
3. Use another system (such as a Novell or Unix system to send the new
firmware file to the Print / Fax server).
A-4
APPENDIX
Reloading firmware using BRAdmin
The BRAdmin application can be used to easily re-program your Brother Print /
Fax server.
1. Start BRAdmin.
2. Highlight the appropriate Print / Fax server. Then press select the
Control menu and choose Load Firmware. You can select more than one
Print / Fax server by pressing CTRL+<select> or SHIFT+<select> on
each additional Print / Fax server.
There are three possible ways of sending the new software version to the Print /
Fax server. For whichever method you select, you must enter a password for the
Print / Fax server. The default password for the Print / Fax server is "access".
3. TFTP PUT from this host
Use this method if you have TCP/IP already installed on your PC. BRAdmin will
use the TFTP protocol to send the new firmware data to the Print / Fax server.
4. TFTP GET from a server
If you have a TFTP server installed in your network (many Unix systems provide
TFTP support), you may wish to use this option. The new firmware file must be
located in the TFTP BOOT directory on your TFTP server. In this case, your PC
makes the Print / Fax server read the firmware data from the assigned TFTP
server. If you do not provide the correct file name, then the upgrade will fail. You
must also ensure that the firmware file is set so that the Print / Fax server can read
the file. On Unix systems you can use the chmod command to specify file
attributes. For example, chmod filename 666 allows the filename to be accessed
by anyone. Also make sure that the TFTP service is running on your Unix server.
5. Netware GET from a server
You must have a Netware server on your network (running IPX/SPX) and you
must store the new firmware file in the SYS/Login directory of the server. In this
case, your PC makes the Print / Fax server read the firmware data from the
assigned Netware server, the Print / Fax server attaches to the Netware server and
reads the firmware itself.
NOTE:
AFTER SENDING FIRMWARE TO THE MFC, DO NOT TURN OFF THE
MFC UNTIL AFTER THE MFC HAS PERFORMED AN AUTOMATIC
RESTART.
A-5
APPENDIX
Reloading using the FTP Protocol
from a command prompt
By specifying the Print / Fax server PASSWORD AS THE USERNAME when
logging on, it becomes possible to upgrade the firmware of the Print / Fax server
or printer. The following example assumes that the Print / Fax server password is
“cambridge”
D:\>ftp
ftp> open 220.0.250.200
Connected to 220.0.250.200.
220 FTP print service:V-1.05/Use the network password for
the ID if updating.
User (220.0.250.200:(none)): cambridge
230 User cambridge logged in.
ftp> bin
200 Ready command OK.
ftp> hash
Hash mark printing on ftp: (2048 bytes/hash mark) .
ftp> send brnt261.blf
200 Ready command OK.
150 Transfer Start
#########################################################
#########################################################
#########################################################
#########################################################
###
226 Data Transfer OK/Entering FirmWareUpdate mode.
ftp: 1498053 bytes sent in 8.52Seconds 175.77Kbytes/sec.
ftp> close
226 Data Transfer OK.
ftp> quit
When you see “226 Data Transfer OK/Entering FirmWareUpdate mode.” You
can be sure that the firmware file is being transferred to the Print / Fax server. If
you do not see this message, the file you are sending to the MFC will either be
ignored or the printer will print garbage.
You must use the “bin” command to put the FTP client into Binary
communications mode. If you do not specify the bin command the upgrade
process will not function correctly.
NOTE:
AFTER SENDING FIRMWARE TO THE MFC, DO NOT TURN OFF THE
MFC UNTIL AFTER THE MFC HAS PERFORMED AN AUTOMATIC
RESTART.
A-6
APPENDIX
Reloading using the FTP Protocol
from a Web Browser
Please visit the Brother Solutions Web site at http://solutions.brother.com for
more information on upgrading the Print / Fax server using a web browser.
A-7
APPENDIX
D
Appendix D
D
Specifications and
Function Table
Specifications
Operating System Support
®
®
®
- Windows 95/98/98SE/Me/NT 4.0 and Windows 2000/XP
- Unix systems supporting LPD
- Mac OS8.6-9.1 / OS 10.1
Protocol Support
- TCP/IP(including the following)
RARP, BOOTP, DHCP, NetBIOS, WINS, LPR/LPD, Port9100,
SMTP/POP3, SMB(NetBIOS/IP), IPP, FTP, TELNET, HTTP,
SNMP,
TFTP
- IPX/SPX
- AppleTalk (EtherTalk)
- DLC/LLC
Network
- 10/100Base-TX Ethernet Network
Network Printing
®
- Windows 95/98/Me Peer-to-Peer Printing
®
®
®
- Windows NT 4.0 / Windows 2000/XP TCP/IP Printing
- Unix TCP/IP Printing
- Novell NetWare Printing
- Quick Draw over AppleTalk
Network Scanning
- B/W Resolution (TIFF-F): 200x100, 200x200dpi
- Color Resolution (JPEG): 150x150, 300x300, 600x600dpi
A-8
APPENDIX
Internet Fax
- T.37 Simple mode
- Tiff-F Profile-S
- Resolution: 200x100, 200x200, 204x98, 204x196dpi
- Coding System: MH
- Width: 1728 dot
- Fax / E-mail / I-Fax Forwarding / Paging feature.
(Please check the User Guide for your Brother MFC to verify is this
feature
is available).
- Internet Fax Relay
- E-mail Relay
- Relay Broadcast
Computer Requirements (for drivers, BRAdmin Professional, Peer-to-Peer
software, etc.)
®
®
- CPU: Pentium 75MHz or Higher for Windows 95/98/98SE/NT 4.0
®
Pentium 150MHz or Higher for Windows Me
®
Pentium 133MHz or Higher for Windows 2000
- RAM: 24MB or greater (32MB recommended) for
®
Windows 95/98/98SE
32MB or greater (64MB recommended) for
®
®
Windows Me/NT 4.0
64MB or greater (128MB recommended) for
®
Windows 2000/XP
For AppleTalk connection
- Computer
Ethernet ready Power Macintosh
- RAM
32MB or more (64MB or more recommended)
- OS
Mac OS 8.6-9.1 / OS 10.1
Open Transport 1.3 or later
Management Utilities
- Web Based Management
Internet Explorer 4.xx or later
Netscape Navigator 4.xx or later
- BRAdmin Professional
A-9
APPENDIX
Function Table and Default Factory Settings
Level One Function
1.SETUP TCP/IP
Level Two Function
1.BOOT METHOD
2.IP ADDRESS
3.SUBNET MASK
4.GATEWAY
5.HOST NAME
6.WINS CONFIG
7.WINS SERVER
8.DNS SERVER
2.SETUP INTERNET
1.MAIL ADDRESS
2.SMTP SERVER
3.POP3 SERVER
4.MAILBOX NAME
5.MAILBOX PWD
3.SETUP MAIL RX
4.SETUP MAIL TX
5.SETUP RELAY
6.SETUP MISC.
1.AUTO POLLING
2.POLL FREQUENCY
3.HEADER
4.DEL ERROR MAIL
5.NOTIFICATION
1.SENDER SUBJECT
2.SIZE LIMIT
3.NOTIFICATION
1.RLY BROADCAST
2.RELAY DOMAIN
3.RELAY REPORT
1.NETWARE
2.NET FRAME *1
3.APPLETALK
4.DLC/LLC
5.NET BIOS/IP
6.ETHERNET
7.TIME ZONE
Options
AUTO/STATIC/RARP/BOOTP/DHCP
[000-255].[000-255].[000-255].[000-255]
[000-255].[000-255].[000-255].[000-255]
[000-255].[000-255].[000-255].[000-255]
(up to 15 characters)
BRN_XXXXXX=(last 6 figures of
Ethernet address)
AUTO/STATIC
PRIMARY/SECONDARY
000.000.000.000/000.000.000.000
PRIMARY/SECONDARY
000.000.000.000/000.000.000.000
(60 characters)
IP ADDRESS / NAME
[000-255].[000-255].[000-255].[000-255]
/ NAME (up to 30 characters)
IP ADDRESS / NAME
[000-255].[000-255].[000-255].[000-255]
/ NAME (up to 30 characters)
(up to 20 characters)
PASSWORD:******
VERIFY:******
(up to 20 characters)
ON/OFF
01 - 60 MIN
ALL/SUBJECT+FROM+TO/NONE
ON/OFF
ON/MDN/OFF
(up to 40 characters)
ON/OFF
ON/OFF
ON/OFF
RELAYXX:
XX=01-10
RELAY01*YYYYY
YYYYY=(up to 30 characters)
ON/OFF
ON/OFF *1
AUTO/8023/ENET/8022/SNAP
ON/OFF
ON/OFF
ON/OFF
AUTO/100B-FD/100B-HD/10B-FD/10BHD
GMTXXX:XX
XXX:XX=-12:00/-11:30.....+11:30/+12:00
*1: 'NET FRAME' setting is available when 'NETWARE' is 'ON'.
A-10
Factory Setting
AUTO
192.000.000.192
000.000.000.000
000.000.000.000
BRN_XXXXXX
AUTO
000.000.000.000
000.000.000.000
brnxxxxxx@example.com
000.000.000.000
000.000.000.000
ON
10 MIN
NONE
ON
OFF
Internet FAX Job
ON
OFF
OFF
01
OFF
ON
AUTO
ON
ON
ON
AUTO
GMT-5:00
INDEX
INDEX
A
I
Address Book ...................................................... 14-6
AIX ....................................................................... 12-3
AIX 4.0 ................................................................. 12-8
Apple Talk ........................................................... 13-3
AppleTalk .......................................................... 13-14
ARP ....................................................... 1-1, 1-6, 12-2
IBM RS/6000 AIX ...............................................12-8
IBM/AS4000.......................................................12-11
IIS.................................................................... 5-1, 6-1
Internet ...................................................................8-1
Internet Explorer ..................................................3-1
Internet Printing ...................................................8-1
IPP...........................................5-1, 5-4, 6-1, 8-1, 8-11
IPX ..........................................................................9-2
IPX/SPX .................................................................1-1
ISP ...........................................................................8-2
B
Berkeley UNIX.................................................... 12-1
BFP Address Book.............................................. 15-9
BFP Port .............................................................. 15-4
BINARY_P1 ...................................... 12-1, 12-4, A-3
BINDERY .............................................................. 9-2
BIP .......................................................................... 8-1
BOOTP..........................................................1-8, 12-2
BRAdmin ............................................................... 1-4
Broadcasting.............................................14-7, 15-11
Brother Internet Fax Printing Software ......... 15-1
Brother LPR port ................................................. 6-4
Brother NetBIOS Port Monitor ..................7-2, 7-4
Brother Network PC Fax Software.................. 14-1
Brother Peer to Peer Print .................................. 6-4
J
JetAdmin ............................................................13-10
JetDirect .................................................................6-1
L
LED .......................................................................13-4
Linux........................................................... 12-1, 12-6
lpc .............................................................. 12-5, 12-12
lpstat......................................................................12-5
M
C
CFGTCP ............................................................ 12-11
D
DEC .................................................................... 12-11
DHCP ..................................... 1-1, 1-5, 6-1, 7-1, 12-2
DLC .............................................................11-1, 11-2
DLC/LLC........................................................... 13-15
DOMAIN ............................................................... 7-2
DOS................................................................ 2-14, 7-1
E
E-mail ..................................................................... 8-2
emailpassword....................................................... 8-6
F
flash memory........................................................ A-4
FTP ............................... 12-2, 12-10, 13-12, A-4, A-7
H
hosts ........................................................................ 6-3
HP distributed print service.............................. 12-7
HP JetDirect.......................................................... 6-1
HP/UX .........................................................12-3, 12-7
HTTP (Hyper Text Transfer Protocol) ......1-1, 3-1
Macintosh.............................................................10-1
mailboxname..........................................................8-6
Microsoft Internet Explorer ................................5-1
Microsoft Internet Print Services ............... 5-1, 6-1
Microsoft TCP/IP printing ..................................5-1
MIME .....................................................................8-2
N
NDPS............................................................... 9-2, 9-3
NDS .........................................................................9-2
NetBIOS ..................................... 2-14, 5-7, 7-1, 13-10
Netscape Navigator ...............................................3-1
Netware 3 ...............................................................9-5
NetWare 3 ..............................................................9-2
NetWare 4 ...................................................... 9-2, 9-5
NetWare 5 ..............................................................9-2
Netware GET........................................................ A-6
network neighborhood ..................................2-14, 7-1
Novell ....................................................................13-3
Novell Distributed Print Services .......................9-3
Novell NetWare .................................................13-13
NT 4.0......................................................................5-1
NWADMIN ............................................................9-2
O
OS/400.................................................................12-11
P
password.................................5-1, 6-1, 7-1, 8-1, 12-1
PCONSOLE...........................................................9-5
Index-1
INDEX
Peer to Peer Printing............................................ 6-1
Peer-to-Peer....................................................... 13-10
ping ....................................................................... 13-3
POP3........................................................ 8-2, 8-3, 8-6
printcap................................................................ 12-5
PRINTCAP.......................................................... 12-1
Printer Agent......................................................... 9-4
PSERVER NLM ................................................. 9-10
R
RARP ..................................................................... 1-7
Reloading firmware............................................. A-6
RFC 1001 ........................................................1-5, 2-3
rlpstat ................................................................... 12-5
router.................................................................... 11-1
S
sam........................................................................ 12-7
SCO UNIX......................................................... 12-10
SCOADMIN ...................................................... 12-10
Server Message Block ................................... 2-14, 7-1
service................................................................... 12-4
Simple Mail Transport Protocol......................... 8-2
smaller networks................................................... 6-1
SMB ............................................................... 2-14, 7-1
smit ....................................................................... 12-8
SMTP ..............................................................8-2, 8-8
Speed Dial ............................................................ 14-5
Sun Solaris 2.x..................................................... 12-9
sysadmsh ............................................................ 12-10
T
TCP/IP ................................................................... 1-1
TELNET .........................1-1, 1-9, 7-3, 8-6, A-1, A-2
TEXT_P1 ........................................... 12-1, 12-4, A-3
TFTP GET............................................................ A-6
TFTP PUT ............................................................ A-6
TGV's Multinet ................................................. 12-11
U
UNIX .................................................................... 12-1
W
Web browser ......................................................... 1-1
WebJetAdmin ...................................................... A-1
Windows 2000 ................... 5-1, 6-1, 8-1, 11-1, 13-12
Windows 2000 Printing.................................5-3, 5-4
Windows 95/98/Me ............................................... 6-1
Windows NT........................................................ 11-1
Windows NT 3.51 ................................................. 5-1
Windows NT 3.5x ..........................................5-1, 8-1
Windows NT 3.5x Printing.................................. 5-9
Windows NT 4.0 Printing..................... 5-6, 5-7, 5-8
Windows XP ........................................... 5-1, 7-1, 8-1
Wollongong's PATHWAY .............................. 12-11
WORKGROUP..................................................... 7-2
X
XP ........................................................................... 7-1
Index-2
Download PDF

advertising