Brother PT-300 Label Maker User Manual

INTRODUCTION
This machine will help you design and print labels for any application.
Extremely versatile, it can create characters of many sizes and styles. In addition,
with the use of colorful tape cartridges, you can print labels with a variety of letter and background colors.
You no longer have to worry about rushing tasks that require professional-type
printing. The quality and performance of this machine make it very versatile.
Although this machine is easy to use, we suggest that you read this manual carefully before starting. Please keep this manual in a handy place for future reference.
Good luck! We hope you enjoy making beautiful custom labels.
FCC NOTICE
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician for help.
Patent numbers and patent publication numbers which are related to
this product are as below:
USP4839742 USP4983058 USP5120147
USP4927278 USP5009530
USP4976558 USP5069557
Use only the adaptor designed exclusively for this machine. See GENERAL PRECAUTIONS on page 5.
CONTENTS
CONTENTS ....................................................................................................
OVERVIEW .....................................................................................................
GENERAL PRECAUTIONS ..............................................................................
BEFORE YOU START ......................................................................................
INSERTING A TAPE CASSETTE .................................................................
INSERTING BATTERIES ............................................................................
CHANGING THE CUTTER UNIT .............................................................
STARTING................................................................................................
CREATING A MESSAGE ..................................................................................
DISPLAY...................................................................................................
MOVING THE CURSOR ..........................................................................
CLEARING THE DISPLAY.........................................................................
KEY OPERATIONS ...................................................................................
INPUT......................................................................................................
SPACE KEY ...............................................................................................
SYMBOLS ................................................................................................
EDITING A MESSAGE .....................................................................................
DELETING ...............................................................................................
WORD OUT ............................................................................................
OVER TYPING .........................................................................................
INSERTING ..............................................................................................
SETTING THE FORMAT ..................................................................................
SIZE .........................................................................................................
BIG SIZE FONT ........................................................................................
STYLE.......................................................................................................
UNDERLINE/FRAME ................................................................................
PRINTING A LABEL ........................................................................................
PRINTING................................................................................................
CUTTING ................................................................................................
REPEAT PRINTING...................................................................................
NUMBERING...........................................................................................
MIRROR PRINTING .................................................................................
TAPE FEED ...............................................................................................
PHRASE MEMORY OPERATION ....................................................................
PHRASE MEMORY...................................................................................
MEMORY SIZE .........................................................................................
STORING THE MESSAGE.........................................................................
RECALLING FROM PHRASE MEMORY....................................................
DELETING THE PHRASE MEMORY .........................................................
MESSAGE LIST ................................................................................................
TROUBLESHOOTING ....................................................................................
SPECIFICATIONS ...........................................................................................
ACCESSORIES.................................................................................................
-1-
1
2
5
6
6
7
8
9
10
10
10
11
12
13
14
15
18
18
20
21
22
24
24
27
28
30
32
32
33
34
35
38
39
42
42
42
42
44
46
48
49
50
51
OVERVIEW
Cover lift
Tape cartridge cover
Tape exit slot
A
STYLE UNDL/FRM BIG
#
$
@
2
3
4
SIZE
!
1
¡
Q
W
NUMBER
REPEAT
ALT
SYMBOL
A
E
S
SHIFT
Z
CAPS
PRINT
MIRROR
D
X
STL
TAPE
%
5
R
T
CODE
Ç
UNDL/FRM
INSERT
¢
6
F
C
A A A
A
CAPS
STORE
&
7
RECALL M. DEL WORD OUT CLEAR
(
)
DEL
*
8
9
0
MEMORY
U
I
O
P
ü
í
ó
á
Y
G
V
AC adaptor slot
ç
SPACE
FEED
H
B
J
N
¿
M
Ñ
K
ñ
L
é
/
, –
SET
TOP
PRINT key CODE key
SET key
RELOC
:
; ’’
ú
?
.
´
ON
OFF
ON/OFF key
To use functions written in pink,
you must press and hold down the CODE key,
then press the desired function key.
LCD display
Tape cutter lever
-2-
Print head
Tape cutter unit
Tape release lever
-3-
Battery compartment latch
Battery compartment
-4-
Tape exit slot
Tape cutter lever
GENERAL PRECAUTIONS
● Use only Brother TZ tapes with this machine. Do not use tapes that do not
have the
mark.
● Four different tape widths are available: 1/4”(6mm), 3/8”(9mm), 1/2”(12mm)
and 3/4”(18mm).
● Do not pull the tape. This may damage the tape cassettes.
● Do not clean the machine with alcohol or other organic solvents. Use only a
soft, dry cloth.
● Remove the batteries and/or disconnect the AC Adaptor if you do not intend
to use your machine for an extended period of time.
(Note: When power is disconnected, any messages in the working area or the
Message Memory area will be lost.)
● Do not put anything onto or into the machine.
● Do not expose the machine to high temperatures or high humidity. Never
leave it on the dashboard or in the back of your car.
● Do not use the machine in dusty places. Keep it out of both direct sunlight
and rain.
● Do not leave any rubber or vinyl on the machine for an extended period of
time. Doing so may cause staining.
● After inserting a new tape cassette, advance the tape by holding down the
CODE key and pressing the FEED key once.
● Do not touch the print head mechanism. If the head is touched, clean it
immediately with a soft wipe (e.g.cotton swab) to avoid permanent damage.
● Use only the AC Adaptor, MODEL AD-30 designed exclusively for this
machine. Use of any adaptor will void warranty.
-5-
BEFORE YOU START
INSERTING A TAPE CASSETTE
Brother TZ tapes are only available in the following widths for this machine:
1/4”(6mm), 3/8”(9mm), 1/2”(12mm) and 3/4”(18mm).
To insert a new tape cassette:
(1) Lift the cassette cover so that you can reach the tape cassette easily. This will
also release the installed cassette.
(2) If there is a tape cassette already in the compartment, remove it by pulling it
straight up.
(3) Remove the stopper from a new tape cassette and if the tape is loose, use
your finger to wind it in the direction of the arrow on the tape cassette until it
is taut. If you are using a previous tape, ensure the tape is taut prior to inserting it into the unit.
Note: ● Some tape cassettes are not provided with a stopper.
(4) Insert the tape cassette firmly into the compartment.
(5) Shut the compartment cover.
(6) Advance the tape by holding down the CODE key and pressing the FEED key
once, then cut the tape.
Note:
●
●
When inserting a tape cassette, make sure that the inner ribbon does
not get caught on the corner of the metal securing stand.
The white lever (release lever) automatically locks when the cover is
closed. If the white lever is manually operated, the cover can not be
closed.
-6-
INSERTING BATTERIES
The machine uses six “AA” size (AM3, LR6, SUM-3, R6) batteries.
To insert batteries:
(1) Turn the machine over. Remove the battery compartment cover by pinching
the latch and lifting.
(2) Follow the diagrams on the back of the compartment to insert the batteries in
the proper direction.
(3) After inserting the batteries, re-fit the battery compartment cover.
When “BATT” (Batteries Weak) is displayed, replace the six batteries.
● Alkaline batteries are recommended.
● An optional AC Adaptor is available. (Model AD-30:7V, 1.2A)
Note:
●
●
When replacing batteries, do so in three minutes or less. Otherwise,
unless an optional AC Adaptor is attached, any message in the working area or Phrase Memory will be lost.
Note the following details when 1.2 V rechargeable NiCd batteries
are used in this machine.
(1) “BATT” will not appear on the display when the rechargeable
batteries are weak or empty. Instead, the power will turn off.
(2) Even after the batteries are recharged, the characters may not be
printed clearly as a result of a low recharging efficiency or the
operating conditions.
-7-
CHANGING THE CUTTER UNIT
When the cutter is not cutting well, replace it with a new one.
To replace a cutter with a dull or broken blade:
(1) Open the tape cassette compartment cover and carefully remove the tape
cassette if it is installed.
(2) Grasp the cutter with your fingers and pull it out.
(3) Grasp the new cutter with the tab on the protective film and insert the cutter
into the machine.
(4) Remove the cutter’s protective film.
(5) Insert the tape cassette, then close the tape cassette compartment cover.
WARNING: Be very careful not to cut yourself when replacing the cutter.
Note:
The expected life of the unit’s cutter is approximately 2000 cuts.
CAUTION
•
•
When changing the cutter unit, be sure not to touch the cutter blade.
Make sure that small children do not try to put the cutter unit in their mouths.
-8-
STARTING
To start the machine:
Press the ON/OFF key.
The machine’s internal memory retains the last message created, and displays it
when you turn on the machine. This feature allows you to stop work on a message, turn off the machine, and return to it later without having to re-enter the
message.
The machine has an automatic power down feature. If the machine is on, but is
not used for five minutes, it will automatically shut off. The message will be
retained in memory until the machine is turned on again.
-9-
CREATING A MESSAGE
DISPLAY
You are now ready to create a message on the machine.
The machine’s LCD display is four characters wide. Actually though, you can
create messages up to 55 characters in length. The four-character display is like a
window which moves across your message.
1234567890123456789012345678901234567890123456789012345
MOVING THE CURSOR
You can review and edit different parts of your message by moving the cursor
backward and forward.
To move the cursor through your message:
Press the
Note:
and
●
●
keys to move the cursor one space at a time.
Hold down the CODE key and press the TOP key to return the cursor to the beginning of the message.
Hold down the CODE key and press the RELOC key to advance the
cursor to the end of a message.
-10-
CLEARING THE DISPLAY
Before entering a new message, you will often need to clear an old message.
To erase the previous message from the display:
Hold down the CODE key and press the CLEAR key.
Example
● Erase any message from the display by pressing
CODE
+
CLEAR
DEL
.
A
A AA
A
CAPS
STL
UNDL/FRM
In the following examples, we will work through a sample message, first creating
it, then editing it, next printing it, and finally storing it in the machine’s memory.
For the purpose of this example, suppose you are J. Smith, and you want to make
a label with your name on it.
-11-
KEY OPERATIONS
CODE KEY
By holding down the CODE key and pushing the appropriate key, you can use
the functions written in pink characters.
SHIFT KEY
By using the SHIFT key you can type capital letters, and symbols located on the
upper part of keys. To type a capital “A”, hold the SHIFT key down and push the
“A” key. To type a “percent” sign “%” (located above the “5”), hold the SHIFT
key down and push the “5” key.
CAPS KEY
By holding down the CODE key and pressing the CAPS key, you set the machine
into CAPS mode. When this mode is entered, the CAPS indicator on the display
turns on. In CAPS mode, capital letters can be typed simply by pressing the character keys. If number keys are pressed, numbers -- not the symbols above them -result. For this reason, CAPS mode is particularly useful for creating messages
containing many numerals and capital letters. To exit CAPS mode, hold down the
CODE key and press the CAPS key.
ALT KEY
By using the ALT key you can type various symbols marked on the keys in green.
To type a symbol located on the right side of a key, hold down the ALT key and
press the key on which the desired symbol is marked.
-12-
INPUT
You can now use the keys to enter a message.
Example
To input “Mr.”:
● Press
SHIFT
CAPS
+
M
ñ
to input a capital M.
A
A AA
A
M
CAPS
STL
● Complete “Mr.” by pressing
A
UNDL/FRM
?
R
then .
/
A AA
A
Mr.
CAPS
-13-
STL
UNDL/FRM
.
SPACE KEY
As on a typewriter, this machine’s SPACE key lets you add a blank space into
your message.
Note:
Example
The SPACE key and the
key have different functions. The
moves the cursor forward without adding blank spaces.
To complete the message “Mr. J Smith”:
Enter the initial “J”:
● Press
SHIFT
CAPS
+
J
¿
to input a capital J.
● Add a blank space by pressing
A
M
SPACE
FEED
once.
A AA
A
r.J
CAPS
STL
UNDL/FRM
● Complete the message by entering “Smith”.
A
A AA
A
Mr.J S m i t h
CAPS
STL
UNDL/FRM
● If you make any mistakes during this input do not worry.
Simply press
CLEAR
DEL
to remove the last character, and input correctly.
-14-
key
SYMBOLS
In addition to the letters, symbols, and numerals on the key tops, there are 57
symbols available in Symbol Mode. These 57 additional symbols are arranged
into 15 groups, corresponding to the numbers A to O on the keyboard.
Group No.
A
SYMBOLS
Ü
B
+
C
•
D
[ ]
E
1
_
2
F
ª
2
G
Group No.
Æ
æ
×
÷
=
J



K
☞
°
º
3
§
♥
I
☞
2
SYMBOLS
L
3
M
N
★
4
O
H
To input a symbol that is not on the key top:
(1) Hold down the CODE key and press the SYMBOL key to enter Symbol
Mode.
(2) The display will read: “A-O?”.
(3) Press the key of the number from A to O whose group contains the symbol
you want. That letter’s group of symbols will be displayed.
(4) Move the cursor to the symbol you want.
(5) Press the SET key.
Note:
●
Press the DEL key to exit Symbol Mode.
-15-
Example
First, make sure that the cursor is located at the place where you want to
add a symbol. To add a telephone symbol ( ) to the message, changing
the message to “Mr. J Smith ”:
● Enter Symbol Mode by pressing
CODE
+
ALT
SYMBOL
.
● The following message will be displayed:
A
A AA
A
A-O?
CAPS
STL
UNDL/FRM
● Press the G key, as its group includes the telephone symbol.
A
A AA
A
2 3 4
CAPS
STL
UNDL/FRM
● The cursor is displayed highlighting the
A
.
A AA
A
2 3 4
CAPS
-16-
STL
UNDL/FRM
● Push
SET
to input a
.
The message should now look like this:
A
A
A AA
Mr.J Sm i t h
CAPS
STL
UNDL/FRM
After a non-keyboard symbol has been entered, the machine automatically exits
from Symbol Mode. If you wish to enter another symbol, you must re-enter Symbol Mode by holding down the CODE key and pressing the SYMBOL key.
-17-
EDITING A MESSAGE
DELETING
The DELETE key allows you to remove characters from your message.
To delete a character:
(1) Using the
and
keys, position the cursor one space to the right of the
character you want to delete.
(2) Press the DELETE key.
Example
To delete the
from the message:
● Make sure the cursor is positioned to the right of the telephone symbol.
A
A AA
A
Mr.J Sm i t h
CAPS
● Press
CLEAR
DEL
STL
to remove the
A
UNDL/FRM
.
A AA
A
Mr.J S m i t h
CAPS
-18-
STL
UNDL/FRM
Now we will delete the blank space between the “J” and “S”:
● Press
TOP
until the cursor is positioned to the right of the blank space
(under the “S”).
A
Mr.J
A
Smit
CAPS
● Press
CLEAR
DEL
A AA
STL
h
UNDL/FRM
to remove the blank space.
A
A AA
A
Mr.J S m i t
CAPS
● Press
TOP
STL
h
UNDL/FRM
to adjust the display in order to check that the blank space
has been deleted.
-19-
WORD OUT
This function allows you to erase one word at a time, simplifying the editing of
long messages.
To use the WORD OUT function:
(1) Position the cursor to the right of the word you want to delete.
(2) Hold down the CODE key and press the WORD OUT key.
A number or word located before the cursor and after the nearest preceeding
space will be deleted.
Example
To delete the word “Mr.” from the message:
● Press
TOP
to position the cursor under “J”.
A
A AA
A
Mr.J
CAPS
● Press
CODE
+
STL
UNDL/FRM
WORD OUT
)
0
to delete “Mr.”.
A
A AA
A
JSmi
CAPS
Smith
STL
-20-
UNDL/FRM
th
OVER TYPING
The machine normally operates in Overtype Mode. In Overtype Mode, you can
change a character simply by typing a new one in its place.
To type over a character:
(1) Move the cursor to the character you want to change.
(2) Press the character or symbol you want.
The new character replaces the old one in the message.
Example
To replace the lower-case letters “mith” with capital letters:
● Position the cursor under the “m”.
A
A AA
A
JSmi
CAPS
STL
th
UNDL/FRM
● Switch to CAPS Mode by pressing
The CAPS indicator will light.
CODE
+
SHIFT
CAPS
● Press the M key.
A
A AA
A
JSMi
CAPS
STL
th
UNDL/FRM
● Complete the process by typing the letters “ITH”.
A
A
A AA
JS M I T H
CAPS
STL
-21-
UNDL/FRM
.
INSERTING
Sometimes you may want to insert a character into the middle of your message.
To do so, you must change from Overtype Mode to Insert Mode.
To insert characters:
(1) Hold down the CODE key and press the INSERT key until display shows
“I : ”.
(2) Move the cursor to the position where you want to insert.
(3) Press the keyboard character or symbol you want to add (see SYMBOLS).
All characters following the insertion will move one space to the right.
Example
To insert a period into the message, changing it to “J. SMITH”:
● Position the cursor under the “S”.
A
A AA
A
J SMIT
CAPS
STL
H
UNDL/FRM
● Enter Insert Mode by pressing
CODE
+
INSERT
¢
6
.
● The following display appears.
A
A AA
A
I:
CAPS
● Pressing the
INSERT
¢
6
STL
×
UNDL/FRM
key while holding down the
between insert and overwrite mode.
-22-
CODE
key toggles
(OVERWRITE MODE)
A
I:
CAPS
(INSERT MODE)
A AA
A
×
STL
?
•
A AA
A
I:
UNDL/FRM
● Release the
● Press the
A
CODE
'
CAPS
STL
key when the display shows “I:
key.
A
A AA
A
J .SMI
CAPS
STL
TH
UNDL/FRM
To leave INSERT Mode:
Holding down the CODE key press the INSERT key again.
-23-
UNDL/FRM
”.
SETTING THE FORMAT
You can print your completed message using a variety of different character sizes,
styles, fonts, underline/frames and tape feed settings.
Choose character size, style, underline/box and tape feed before printing the
label.
Note:
The type of character you choose will be used for all the characters in
your message. It is not possible to have two different character sizes or
styles within one message.
SIZE
There are five different character sizes you can select for your label:
1 - Standard Size
W2 - Double Width
H2 - Double Height
4 - Double Width & Double Height
8 - 4 x Width & Double Height
-24-
To choose a character size:
(1) Holding down the CODE key, press the SIZE key to change the character
size. The size indicator on the display advances in the order shown.
1
W2
H2
A
A
A
CAPS
STL
4
8
A A
UNDL/FRM
(2) Stop pressing the SIZE key when your desired character size is indicated.
Example
To use Double Width and Double Height (4) characters:
● Hold down
CODE
and press
SIZE
!
1 ¡
until the size indicator is
aligned with the A.
A
A
A AA
J .SMI
CAPS
STL
TH
UNDL/FRM
Note: When the BIG font is selected, the size is fixed to the BIG size
whatever the SIZE setting.
-25-
Note:
The size of the characters that can be printed are limited by the width
of the tape.
Tape width
Possible character sizes
3/4”(18mm)
1, W2, H2, 4, 8, BIG
3/4”(12mm)
1, W2, H2, 4, 8
3/8”(9mm)
1, W2, H2, 4, 8
1/4”(6mm)
1, W2
If a character size is set which is not shown in the above table for the tape width
being used and the PRINT key is pressed, an error message will be displayed and
the label can not be printed.
-26-
BIG SIZE FONT
This machine has a BIG size font in addition to the normal font. The normal size
font can be set at the standard size, W2 (double width), H2 (double height), 4
(double width & double height) and 8 (4 × width & double height). If the BIG size
font is chosen, all other settings are cancelled.
To choose the BIG size font:
(1) Holding down the CODE key, press the BIG key. The display shows
“NORM” or “BIG”, whichever is the currently selected font size.
(2) Pressing the BIG key while holding down the CODE key toggles the displays.
(3) Release the CODE key when a desirable font size is selected on the display.
It will change as follows:
A AH2 A4
ND O: RN MO R M
A
STL A
1
CAPS
A
●
●
STL
UNDL/FRM
UNDL/FRM
A AA
B I G
CAPS
Note:
W2
A
STL
UNDL/FRM
When the BIG size font is selected, all lower case characters are
printed in upper case, and the settings for SIZE, STYLE and UNDL/
BOX are ignored.
The BIG size font can only be set when tape with a 3/4” (18 mm)
width is used.
-27-
STYLE
There are also nine different print styles:
Normal (NORM)
Italic (ITAL)
Outline (OUTL)
Italic + Outline (IT+O)
Bold (BOLD)
Italic + Bold (IT+B)
Shadow (SHAD)
Italic + Shadow (IT+S)
Vertical (VERT)
To choose a print style for your label:
(1) Holding down the CODE key, press the STYLE key once. The display will
show the current print style.
(2) Still holding down the CODE key, press the STYLE key again. The available
print styles will appear in order as you press the STYLE key.
(3) When the style you want is displayed, release the CODE key.
If you select a style other than Normal, the style indicator will be visible on the
display.
-28-
Note:
●
●
Example
Only Normal style characters can be printed vertically.
Vertical printing can not be used with some tape width and character
size combinations.
To use Outline print:
● Hold down
● Press
STYLE
@
2
CODE
.
until the display reads “OUTL”.
The style indicator turns on.
A
A AA
A
OUTL
CAPS
● Release
CODE
.
-29-
STL
UNDL/FRM
UNDERLINE/FRAME
You can add an underline or frame text when you wish to emphasize it.
To add Underline or Box around the text.
(1) Holding down the CODE key, press UNDERLINE/FRAME (
UNDL/FRM
#
3
) key.
(2) The current style will be shown on the display.
(3) Still holding down the CODE key, press UNDERLINE/FRAME key to change
the style.
It will change as follows:
A A
AA AA A A
A
A
T E X T
CAPS
STL
A A
CAPS
STL
CAPS
Note:
●
●
●
STL
UNDL/FRM
A A
AA AA A A
A
B O X 1
STL
A
B O X 3
A A
CAPS
UNDL/FRM
A A
UNDL/FRM
AA AA A A
STL
AA AA A A
A
U N D L
CAPS
A AA
B O X 4
UNDL/FRM
AA AA A A
A
A
B O X 2
UNDL/FRM
CAPS
STL
UNDL/FRM
Underline & Box are not available simultaneously.
The underline or box will not be printed when the Vertical is used.
Printing of the underline or frame are limited by the tape width and
character size setting.
-30-
Tape width
Possible character sizes
3/4” (18 mm)
1, W2, H2, 4, 8, BIG
1/2” (12 mm)
1, W2, H2, 4, 8
3/8” (9 mm)
1, W2, H2, 4, 8
1/4” (6 mm)
1, W2
A triangle indicator on the display appears whether Underline or Frame is set on.
Box 1
Box 3
Box 2
Box 4
-31-
PRINTING A LABEL
PRINTING
After you have chosen the character size, print style and tape feed style, you are
ready to print the label.
To print a label:
Press the PRINT key.
The printed label comes out of the tape exit slot on the side of the machine.
Press the CODE + FEED key before cutting the tape if TAPE FEED mode is set to
“_”, “#”, “##” or “###”.
Example
To print the message onto a label:
● Press
PRINT
MIRROR
.
A label reading “J. SMITH” written in Double Width & Double Height
Outline characters will be printed.
Note:
●
●
Do not pull on the tape. This may damage the tape cassette.
Do not attempt to cut the tape during printing or feeding.
-32-
CUTTING
To cut the tape:
Pull out the tape cutter lever on the side of the machine.
Example
To cut the label:
● Pull out the tape cutter lever.
MIT H .SMITH
J
Note:
If you pull out the tape cutter lever too far, it may break.
To attach the label:
Remove the label backing and attach the label at the desired position.
-33-
REPEAT PRINTING
The Repeat function allows you to repeatedly print the same label up to nine
times.
To use the REPEAT PRINTING function:
It is recommended to set the TAPE FEED mode to “#”, “##” or “###”. (Please refer
to page 39.)
W
(1) Hold down the CODE key and press the REPEAT ( REPEAT
) key.
(2) The following message appears on the display:
A
A AA
A
1-9?
CAPS
STL
UNDL/FRM
(3) Select the number of labels you want. For example, if you want nine labels to
be printed, type 9.
(4) Press print.
Press the CODE + FEED keys before cutting the tape if the TAPE FEED mode
is set to “-”, “#”, “##” or “###”.
Note:
CLEAR
DEL
●
Press
●
A maximum of nine copies can be printed.
Cutting is not done automatically.
Before starting a repeat print, check that there is sufficient tape in the
cartridge.
Never try to cut the tape during printing.
Press the ON/OFF key immediately if the tape runs out before all the
printing is finished. (striped tape will appear.)
●
●
●
●
before printing; the previous screen reappears.
-34-
NUMBERING
The NUMBERING function can be used to automatically increment numbers
included in otherwise identical texts. For example, when printing text with a
series of dates (“JULY 4, 1962”; “JULY 5, 1962”; and “JULY 6, 1962”), the auto
count function will enable printing of all three texts in a single print operation.
To use the AUTO COUNT function when printing:
It is recommend to set the TAPE FEED mode to “#”, “##” or “###”. (Please refer to
page 39.)
(1) Type in message to be printed.
(2) Position the cursor beneath the number in the text to be incremented. Then
hold down the CODE key and press the NUMBER
changes as follows:
A
JU L Y
A
key. The display
A AA
A
CAPS
Q
NUMBER
4
STL
, 1962
UNDL/FRM
A AA
A
1-9?
CAPS
STL
UNDL/FRM
(3) The screen will prompt the selection of the last number to be printed. (In the
example described above, the last number would be 6.)
(4) Press PRINT and the text will be printed out. Printing will be repeated, with
the number specified incremented to the next number. This operation will
continue until the last number is reached.
Press the CODE + FEED keys before cutting the tape if the TAPE FEED mode
is set to “-”, “#”, “##” or “###”.
Note:
●
●
●
Before printing, you can press the DELETE key to erase the number
you have entered. Pressing DELETE again will exit the NUMBERING
mode.
The last number to be printed must be selected from within the range
1-9.
If you enter a number that is lower than the one originally entered in
the text, printing will be disabled, and an “ERR” (ERROR) message
will appear on the display if you press the PRINT key.
-35-
●
●
Example
Numbers are always incremented one at a time.
If the battery becomes weak during a NUMBERING operation, the
operation will be interrupted.
To use the NUMBERING function:
● Position the cursor beneath the number in the text to be incremented.
A
A AA
A
JU L Y
CAPS
CODE
● Hold down the
changes as follows:
4
STL
UNDL/FRM
key and press the
A
A AA
A
1-9?
CAPS
-36-
STL
UNDL/FRM
Q
NUMBER
key. The display
● Press numeric key “6”.
A
A AA
A
6
CAPS
● Press
PRINT
MIRROR
STL
UNDL/FRM
. Your text will be printed out.
● The number will automatically be incremented by one, and the text
will be printed out again.
● The printing operation will be repeated until the number you selected
as the last number has been printed out. When printing has completed,
the following display appears.
A
A AA
A
JU L Y
CAPS
-37-
STL
6
UNDL/FRM
MIRROR PRINTING
For this application, tape with a clear adhesive must be used.
When the mirror Printing function is used, characters are printed so as to be legible from the adhesive side of the tape. If the labels are then attached to glass or
some other transparent material, they can be read correctly from the opposite
side. This type of label is particularly useful for attachment to the inside of shop
windows or clear notebooks, so that it can be read from the outside. For this
application, transparent tape must be used.
O WON
AS N
EL
NOW ON SALE
Mirror-printed labels attached inside the window can be read from the street.
To use Mirror Printing:
(1) Holding down the CODE key, press the MIRROR (
(2) The current print mode (M:
PRINT
MIRROR
) key.
or M:×) appears on the display.
(3) Still holding down the CODE key, press the MIRROR key again. The display
changes between the following two messages:
(MIRROR PRINTING)
A
A AA
A
M:
CAPS
STL
A
×
A AA
A
M:
UNDL/FRM
CAPS
STL
UNDL/FRM
(4) If you want to use Mirror Printing, release the CODE key when “M: ” is
displayed. To use regular printing, release the CODE key when “M: ×” is displayed.
Note:
The Mirror Printing function automatically turns off when the machine
is turned off. If you want to use Mirror Printing again after the power
has been turned off, you must turn on the Mirror printing function
again.
-38-
TAPE FEED
The tape feed function can be used to leave equal margins on the left and right
sides of the label. The margins can be set to any of the following four widths:
1/6”(4mm), 1/3”(8mm), 1/2”(12mm) or 1”(24mm). When continuously printing
labels, the labels can be printed without extra margins. In addition, this function
is very convenient when printing more than one label with multiple styles while
changing the styles each time a label is printed.
To change the TAPE FEED Mode:
(1) Press and hold down the CODE key, then press the TAPE key.
(2) The current feed mode appears on the display.
(3) While still holding down the CODE key, press the TAPE key again. The display changes as shown below.
A
A AA
A
# # # #
CAPS
A
STL
A AA
A
CAPS
A
UNDL/FRM
STL
UNDL/FRM
A AA
A
#
CAPS
A
STL
UNDL/FRM
A AA
A
# #
CAPS
A
A
STL
UNDL/FRM
A AA
# # #
CAPS
STL
-39-
UNDL/FRM
Note:
Example
SPACE
When “- ”, “# ”, “## ” or “### ” is set, press CODE
+ FEED
to
feed the tape after the label is printed and before the tape is cut. If the
tape is not fed before being cut, some of the printed characters may be
cut off. (See the illustrations below.)
● When “####” is set, the tape is automatically fed 1”(24mm) after the
label is printed. If the tape is cut without being fed, a label like that
shown in the illustration below is produced.
1”
(24mm)
● When “printed. If
1”
(24mm)
” is set, the tape is not automatically fed after the label is
CODE
+
SPACE
FEED
is pressed to feed the tape and the tape
is cut, a label like that shown in the illustration below is produced.
1”
(24mm)
● When “# ” is set, 4mm of the tape is automatically fed after the label is
printed. If
CODE
+
SPACE
FEED
is pressed to feed the tape and the tape
is cut, a label like that shown in the illustration below is produced.
Please cut the tape on the “:” mark with scissors.
1”
1/6”
(24mm) (4mm)
-40-
1/6”
(4mm)
If the tape is cut at the cutline, the text is centered in the middle of the
label. The tape is automatically fed 1/3”(8mm) when “## ” is set, and
1/2”(12mm) when “### ” is set.
● Continuous printing
When “# ” is set and three labels are printed continuously, the tape is
fed and a label like that shown in the illustration below is produced. If
“## ” or “### ” is set, the labels are printed with the appropriate margin widths. Please cut the tape on the “:” mark with scissors.
1. Repeat printing (See page 34.)
1”
1/6”
(24mm) (4mm)
1/6”1/6”
(4mm)(4mm)
1/6”1/6”
(4mm)(4mm)
1/6”
(4mm)
2. Numbering (See page 35.)
● Printing with different styles
When “- ” is set, different styles can be used to print one label since the
tape is not fed after a label is printed, different characters can be
entered and the style can be changed. If the new label is printed, it will
continue printing from the point where the first label stopped. After the
whole label is printed, feed and cut the tape.
-41-
PHRASE MEMORY OPERATION
PHRASE MEMORY
You can use the Phrase Memory function to store your most frequently used messages. Text stored in the Phrase Memory will not be deleted by the usual message
clear operation (CODE + CLEAR).
You can easily recall your message from this Phrase Memory any time you want
to work with it.
MEMORY SIZE
In the Message Phrase you can store up to a total of 300 characters. These 300
characters can be divided into as many as nine areas.
The maximum capacity for any single area is 55 characters.
Note:
When replacing batteries, do so in three minutes or less. Otherwise,
unless an optional AC Adaptor is attached, any message in the working
area or Phrase Memory will be lost.
STORING THE MESSAGE
To store the currently displayed message in the PHRASE MEMORY:
(1) Type message to be stored.
(2) Hold down the CODE key and press the STORE key.
(3) The display will read:
A
A AA
A
1-9?
CAPS
STL
UNDL/FRM
(4) Press a key from 1 to 9 to select a storage area.
(5) Your message is stored in the memory area you selected, and the display
clears.
-42-
If the area you select is already being used, an error message will briefly appear,
and then the display will again ask you to choose an area. In that event, please
select a different number from 1 to 9.
If all nine areas are being used, you must clear one of them before you can store
your current message.
Also, when 300 characters are already stored in the Phrase Memory and you try
to store more, the message “FULL”, will appear on the display. You must delete
one of the memory areas before you can store your current message.
See DELETING THE MESSAGE MEMORY.
Example
To store the message “J. SMITH” in the Phrase Memory:
● Make sure the message is in the working area (on the display).
A
A AA
A
J.SM
CAPS
● Press
CODE
+
STL
STORE
&
7
ITH
UNDL/FRM
. The following guidance message appears on
the display:
A
A AA
A
1-9?
CAPS
STL
UNDL/FRM
● Press a number key from 1 to 9.
This time for example, press 1.
The message is stored, in the Phrase Memory.
Note: Before you enter an area number you can cancel storage by pressing
CLEAR
DEL
.
-43-
RECALLING FROM PHRASE MEMORY
To recall a message stored in one of the nine PHRASE MEMORY areas:
(1) Holding down the CODE key, press the RECALL key.
(2) The display will read:
A
A AA
A
1-9?
CAPS
STL
UNDL/FRM
(3) Select the number of the area you want to recall, and press it.
(4) The key number and the beginning of the message appear on the display.
If you selected the wrong number, you can now press a new number key
(1-9) to display the correct phrase.
(5) When your desired message is on the screen, press the SET key.
(6) The Phrase Memory you select is recalled into the working area for use.
Note:
●
●
Example
The character size, print style, and underline/box that are recalled
are the same as those that were saved with the text.
When a message is recalled from the PHRASE MEMORY, any message currently on the display is cleared.
To recall “J. SMITH” from the Phrase Memory:
RECALL
● Press
CODE
+
*
8
. The following guidance message appears on
the display:
A
A AA
A
1-9?
CAPS
STL
-44-
UNDL/FRM
● Press 1, since you stored your message in area 1.
The stored message appears on the display, along with its area number.
A
A AA
A
1:J.
CAPS
STL
UNDL/FRM
To alter recalled memory:
● Press
SET
. The message is moved to the working area and
remains on the display.
A
A AA
A
J.SM
CAPS
STL
ITH
UNDL/FRM
● You can see the current printing information on the display for STL,
UNDL/FRM and the SIZE and BIG size settings.
● You can check the style (UNDL/FRM) by pressing the
UNDL/FRM
#
3
CODE
+
(UNDL/FRM).
● Now you can print or edit the message.
Note: Before you press
CLEAR
DEL
SET
.
-45-
you can cancel recall by pressing
DELETING THE PHRASE MEMORY
To delete an area of PHRASE MEMORY:
(1) Hold down the CODE key and press the M.DEL key. The following message
appears on the display:
A
A AA
A
1-9?
CAPS
STL
UNDL/FRM
(2) Select the number key (1-9) of the memory area you want to delete, and
press it.
The key number and the beginning of the message appear on the display.
If you accidentally selected the wrong number, you can press another number key (1-9) to display the correct phrase.
(3) When your desired message is on the screen, press the SET key.
(4) The Phrase Memory area is cleared and the message previously in the working area reappears on the display.
Example
To delete “J. SMITH” from the Phrase Memory:
● Press
CODE
+
M.DEL
(
9
. The following guidance appears on the dis-
play:
A
A AA
A
1-9?
CAPS
STL
-46-
UNDL/FRM
To delete Phrase Memory
● Press 1.
The stored message appears on the display.
A
A AA
A
1:J.
CAPS
● Press
SET
STL
UNDL/FRM
. The message is deleted from the memory. The message
previously in the working area (in this case, the same “J. SMITH”)
appears on the display.
Note: Before you press
CLEAR
DEL
SET
you can cancel deletion by pressing
.
Now you can use the cleared memory area “1” to store another message.
-47-
MESSAGE LIST
ERR
BATT
FULL
NORM
OUTL
BOLD
SHAD
ITAL
IT+O
IT+B
IT+S
VERT
A-O?
1-9?
BIG
####
–
#
##
###
M:
M: ×
TEXT
UNDL
BOX 1
BOX 2
BOX 3
BOX 4
I:
I: ×
Input error. The selected tape type is incorrect.
The batteries are weak or empty.
The working area is full (max: 55 characters) or the
Phrase Memory is full (see page 42).
See page 28.
See page 15.
See page 34, 35, 42, 44, 46.
The BIG size font is selected.
See page 39.
Mirror printing.
Cancels mirror printing.
Prints without underline/frame.
Underlines characters.
Frame characters.
Insert Mode is ON.
Insert Mode is OFF.
-48-
TROUBLESHOOTING
Problem
What to Do
1. The display stays blank after you
have turned on the machine.
●
●
●
2. The machine does not print, or the
printed characters are blurred.
●
●
●
Check the polarity of the batteries.
If the batteries are low, replace
them.
Check that the adaptor is working
properly.
Check that the tape cassette has
been inserted properly.
If the tape cassette is empty, replace it with a new one.
Check that the character size is
appropriate for the width of the
tape that is used.
3. The printed characters are not
formed properly.
●
The batteries are probably weak.
Replace them.
4. The tape cannot be cut.
●
The cutting blade is probably dull.
Replace the cutter unit.
5. Striped tape appears.
●
You have reached the end of the
tape. Replace it with a new tape.
6. The memory has cleared on its
own.
●
The batteries are probably weak.
Replace them.
7. An unprinted line appears on a
label.
●
There may be some dust on the
print head. Wipe the print head
gently with a dry cotton swab.
If dust still remains, dip the cotton
swab in isopropyl (rubbing) alcohol and wipe the print head again.
●
-49-
SPECIFICATIONS
Input Device:
49 keys (39 character keys and 10 function keys)
Print Speed:
10 mm/sec.
Character Size:
Standard Size (1)
Double Width (W2)
Double Height (H2)
Double Width & Double Height (4)
4 x Width & Double Height (8)
BIG SIZE (ALL INDICATORS ON, STYLE FIXED, NO
UNDERLINE/FRAME)
Internal Character:
Font: HELSINKI
Print Tape:
Pressure-sensitive adhesive-based (TZ TAPE ONLY)
3/4” (18mm) (W) × 315”(8m) (L)
1/2” (12mm) (W) × 315”(8m) (L)
3/8” (9mm) (W) × 315”(8m) (L)
1/4” (6mm) (W) × 315”(8m) (L)
LCD:
7 x 5 dots
Power Supply:
Batteries (AA/SUM-3/AM3/R6/LR6) or optional AC Adaptor. (AD-30:7V 1.2A)
Alkaline batteries are recommended.
The power automatically turns off when no key is pushed
for five minutes.
Dimensions:
6.85”(174mm) (W) × 7.87”(200mm) (D) × 2.36”(50mm)
(H)
Weight:
1.4lb(0.65kg) (without batteries)
Memory Buffer Size:
55 characters
Phrase Memory Size:
300 characters maximum 9 available storage areas
1line x 4 columns
-50-
ACCESSORIES
●
Supplies
Obtain tape cassettes, AC Adaptors and tape cutters from your nearest authorized dealer. Brother cannot be held responsible for trouble caused by the use
of unauthorized supplies.
Use only Brother TZ tapes with this machine. Do not use tapes that do not
have the
mark.
Stock No.
Description
QTY/
PACKAGE
PRICE
1
1
1
1
1
1
1
1
1
1
1
1
$20.99
$20.99
$20.99
$20.99
$20.99
$24.99
$23.99
$20.99
$20.99
$23.99
$20.99
$20.99
1
$24.99
1
1
1
$20.99
$23.99
$23.99
1
$23.99
1
1
1
1
$16.99
$17.99
$17.99
$20.99
3/4” (18mm)-wide laminated tapes
TZ-141
TZ-145
TZ-241
TZ-242
TZ-243
TZ-344
TZ-345
TZ-441
TZ-541
TZ-545
TZ-641
TZ-741
TZ-B41
TZ-M41
TZ-WB41
TZ-WT41
TZ-WS41
Black characters on clear tape
White characters on clear tape
Black characters on white tape
Red characters on white tape
Blue characters on white tape
Gold characters on black tape
White characters on black tape
Black characters on red tape
Black characters on blue tape
White characters on blue tape
Black characters on yellow tape
Black characters on green tape
Black characters on fluorescent
orange tape
Black characters on clear (matte) tape
Black characters on Bugs Bunny tape
Black characters on Taz tape
Black characters on Tweety &
Sylvester tape
1/2” (12mm)-wide laminated tapes
TZ-131
TZ-231
TZ-232
TZ-335
Black characters on clear tape
Black characters on white tape
Red characters on white tape
White characters on black tape
-51-
Stock No.
Description
QTY/
PACKAGE
PRICE
1
1
1
1
$14.99
$16.99
$18.99
$16.99
1
1
1
$12.99
$14.99
$17.99
QTY/
PACKAGE
PRICE
1
$29.99
1
$24.99
QTY/
PACKAGE
PRICE
1
$37.99
1
$24.99
QTY/
PACKAGE
PRICE
1
1
$24.99
$9.99
3/8” (9mm)-wide laminated tapes
TZ-121
TZ-221
TZ-325
TZ-421
Black characters on clear tape
Black characters on white tape
White characters on black tape
Black characters on red tape
1/4” (6mm)-wide laminated tapes
TZ-111
TZ-211
TZ-315
Black characters on clear tape
Black characters on white tape
White characters on black tape
Special tapes
Stock No.
TZ-SE4
TZ-FA3
Description
Black characters on 3/4” (18-mm)wide security tape
Blue characters on 1/2” (12-mm)wide fabric tape
Stamp kit
Stock No.
SK-MB
SH-MB
Description
Stamp-making kit for Medium stamp
with black ink
Additional stamper for Medium stamp
with black ink
OPTIONS
Stock No.
AD-30
TC-9
Description
AC ADAPTER
TAPE CUTTER
Most retailers and distributors carry a full line of tape cassettes. If you wish to
order accessories for your P-Touch direct from Brother, please refer to the “Accessory Order Form” or visit us on-line at “http://www.brothermall.com”.
-52-
P-TOUCH ACCESSORY ORDER FORM
Dear Customer:
This order form is provided for your convenience should your retailer not stock the
item(s) needed. To order by mail, send this completed form along with proper payment to
the address below OR credit card holders: Call toll-free 1-888-879-3232, fax completed
order form to 1-800-947-1445, or visit our web site at http://www.brothermall.com.
Please refer to the Accessories listing in your User's Guide for stock no. and price.
Stock No.
Description
Price
Quantity
Total
Subtotal
Name:
Accessory Subtotal:
Address:
AZ, CA, CO, CT, FL, GA, IL, LA, MA,
MD, MI, MN, MO, NC, NJ, NV, NY,
OH, PA, TN, TX, VA, WAresidents
$
add applicable sales tax
City:
State/Zip:
$
Daytime Phone:
Shipping/Handing Options
SEND ORDER FORM TO:
Please choose one:
Brother International Corp.
Attn: Consumer Accessory Div.
P.O. Box 341332
Bartlett, TN38184-1332
• Standard ($5.00)
• 2nd day air freight ($8.75) Mandatory for all
deliveries outside of the continental U.S.
(Alaska, Hawaii, Puerto Rico, Virgin Islands
& Canada)
• All other overseas orders ($25.00) $
TOTAL DUE (US dollars)
$
Method of payment (Check one)
(
) Visa (
) MasterCard (
) Discover (
) American Express (
) Check/Money Order
Account Number
Expiration Date
✂
Signature
* Prices subject to change without notice.
P-TOUCH ACCESSORY ORDER FORM
Dear Customer:
This order form is provided for your convenience should your retailer not stock the
item(s) needed. To order by mail, send this completed form along with proper payment to
the address below OR credit card holders: Call toll-free 1-888-879-3232, fax completed
order form to 1-800-947-1445, or visit our web site at http://www.brothermall.com.
Please refer to the Accessories listing in your User's Guide for stock no. and price.
Stock No.
Description
Price
Quantity
Total
Subtotal
Name:
Accessory Subtotal:
Address:
AZ, CA, CO, CT, FL, GA, IL, LA, MA,
MD, MI, MN, MO, NC, NJ, NV, NY,
OH, PA, TN, TX, VA, WAresidents
$
add applicable sales tax
City:
State/Zip:
$
Daytime Phone:
Shipping/Handing Options
SEND ORDER FORM TO:
Please choose one:
Brother International Corp.
Attn: Consumer Accessory Div.
P.O. Box 341332
Bartlett, TN38184-1332
• Standard ($5.00)
• 2nd day air freight ($8.75) Mandatory for all
deliveries outside of the continental U.S.
(Alaska, Hawaii, Puerto Rico, Virgin Islands
& Canada)
• All other overseas orders ($25.00) $
TOTAL DUE (US dollars)
$
Method of payment (Check one)
(
) Visa (
) MasterCard (
) Discover (
) American Express (
) Check/Money Order
Account Number
Expiration Date
✂
Signature
* Prices subject to change without notice.
GUIA DEL USUARIO
INTRODUCCION
Esta máquina le ayudará a diseñar e imprimir etiquetas para cualquier
aplicación.
Es muy versátil y puede utilizarse para crear caracteres de varios tamaños y
estilos. Además, con el empleo de las cintas de colores, podrá imprimir las
etiquetas con colores diferentes para las letras y para el fondo.
Ya no será necesario que se preocupe por las tareas que requieren una impresión
tipo profesional. La calidad y rendimiento de esta máquina la convierten en una
máquina muy versátil.
Aunque esta máquina es fácil de utilizar, le aconsejamos que lea atentamente
este manual antes de empezar. Conserve este manual en un lugar de fácil acceso
para poderlo consultar cuando sea necesario.
¡Buena suerte! Esperamos que disfrute haciendo hermosas etiquetas personales.
AVISO DE LA FCC
Este equipo ha sido probado y cumple con los límites de un aparato digital de la Clase B, siguiendo el apartado 15 de las normas de la FCC. Estos
límites están pensados para proporcionar una protección razonable contra interferencias nocivas dentro de una instalación residencial. Este
equipo podría interferir de forma nociva con comunicaciones por radio
si no se instala y utiliza siguiendo las instrucciones. No obstante, no existe ninguna garantía de que no vayan a suceder interferencias en una instalación concreta. Si este equipo causara interferencias nocivas con la
recepción de radio o televisión, lo cual puede determinarse poniendo el
equipo en ON u OFF, se recomienda que el usuario intente corregir dichas interferencias mediante una de las siguientes medidas:
- Reoriente o ponga la antena receptora en otro lugar.
- Aumente la separación entre el equipo y el receptor.
- Conecte el equipo en una toma de un circuito diferente de la
que esté conectada el receptor.
- Consulte a su distribuidor o a un técnico experimentado de
radio/televisión.
A continuación se indican los números de patente y de publicación de
patente relacionados con este producto:
USP4839742 USP4983058 USP5120147
USP4927278 USP5009530
USP4976558 USP5069557
Emplee sólo el adaptador diseñado exclusivamente para esta máquina. Vea las
precauciones generales en la página 2.
ÍNDICE
PRECAUCIONES GENERALES ........................................................................
ANTES DE EMPEZAR ......................................................................................
INSERCION DE UN CASSETTE DE CINTA ...............................................
INSERCION DE LAS BATERIAS ................................................................
CAMBIO DE LA CUCHILLA .....................................................................
OPERACIONES DE LAS TECLAS ..............................................................
CREACION DE UN MENSAJE .........................................................................
PANTALLA ...............................................................................................
DESPLAZAMIENTO DEL CURSOR...........................................................
SIMBOLOS...............................................................................................
EDICION DE UN MENSAJE .....................................................................
TAMAÑO.................................................................................................
ESTILO .....................................................................................................
SUBRAYADO/ENCUADRE .......................................................................
IMPRESION Y CORTE ..............................................................................
IMPRESIÓN REPETIDA ............................................................................
NUMERACIÓN ........................................................................................
IMPRESION INVERTIDA ..........................................................................
AVANCE DE LA CINTA ............................................................................
OPERACION DE LA MEMORIA DE FRASES ...................................................
MEMORIA DE FRASES .............................................................................
LISTA DE MENSAJES .......................................................................................
ACCESORIOS .................................................................................................
-1-
2
3
3
4
5
6
7
7
7
8
9
10
12
13
14
15
16
17
18
19
19
21
22
PRECAUCIONES GENERALES
● Utilice solamente cintas TZ Brother con esta máquina. No utilice cintas que
no tengan la marca
.
● Las cintas están disponibles en cuatro anchuras diferentes: 1/4” (6 mm), 3/8”
(9 mm), 1/2” (12 mm) y 3/4” (18 mm).
● No tire de la cinta. Si lo hiciese podría dañar los cassettes de cinta.
● No limpie el P-Touch con alcohol ni otros disolventes orgánicos. Utilice
únicamente un paño suave y seco.
● Retire las baterías y/o desconecte el adaptador de CA si no va a utilizar el PTouch por un periodo de tiempo prolongado. (Nota: Al apagar el P-Touch, se
perderán los mensajes del área de trabajo del área de Mensajes de Memoria.)
● No deposite nada sobre el P-Touch ni en su interior.
● No exponga el P-Touch a temperaturas elevadas ni a altos índices de
humedad. No la abandone en cualquier lugar ni lo guarde en el maletero de
su autómovil.
● No utilice el P-Touch en lugares con mucho polvo. Evite la incidencia directa
de la luz solar y la exposición a la lluvia.
● No deje objetos de goma o vinilo sobre el P-Touch por largo periodo de
tiempo. Estos materiales podrían ocasionar oxidación.
● Después de insertar el nuevo cassette de cinta, avance la cinta pulsando las
teclas CODE y FEED una vez.
● No toque el mecanismo del cabezal impresor. Si toca el cabezal, límpielo
inmediatamente con un paño suave (por ejemplo, algodón) para evitar daños
permanentes.
● Utilice solamente el adaptador de CA, modelo AD-30 diseñado
exclusivamente para esta máquina.
-2-
ANTES DE EMPEZAR
INSERCION DE UN CASSETTE DE CINTA
Las cintas TZ Brother están sólo disponibles en las anchuras siguientes para esta
máquina: 1/4”(6 mm), 3/8”(9 mm), 1/2”(12 mm) y 3/4”(18 mm).
Para insertar un nuevo cassette de cinta:
(1) Levante la cubierta del cassette de modo que pueda tener acceso con
facilidad al cassette de cinta. De este modo también se liberará cualquier
cassette que haya instalado.
(2) Si en el compartimiento hubiera una cassette de cinta vacía, sáquela
levantándola.
(3) Extraiga el tope del cartucho de cinta nuevo, y si la cinta está floja, emplee
un dedo para bobinarla en la dirección de la flecha, que hay en el cartucho
de cinta, hasta que quede tensada. Si emplea una cinta que ha empleado
antes, asegúrese de que la cinta esté tensada antes de insertarla en la unidad.
Nota:
●
Algunos cassettes de cinta no disponen de retén.
(4) Inserte el nueva cassette de cinta firmemente en el compartimiento.
(5) Cierre el cubierta del compartimiento.
(6) Avance la cinta pulsado la tecla CODE y luego una vez la tecla FEED, y corte
entonces la cinta.
Nota:
●
●
Cuando inserte un cassette de cinta, compruebe que la cinta interior
no quede atrapada en el ángulo del soporte metálico de seguridad.
La palanca blanca (palanca de liberación) se bloquea automáticamente cuando se cierra la cubierta. Si la palanca blanca es
accionada manualmente, no podrá cerrarse la cubierta.
-3-
INSERCION DE LAS BATERIAS
La máquina usa seis baterías de tamaño “AA” (AM3, LR6, SUM-3, R6).
Para insertar las pilas:
(1) Dé la vuelta al P-Touch. Retire la cubierta del compartimento de las baterías
presionando el pestillo y levantando la cubierta.
(2) Siga los diagramas del fondo del compartimento para insertar las baterías en
la dirección correcta.
(3) Una vez colocadas las baterías, vuelva a colocar la cubierta del
compartimento de las baterías.
Cuando aparezca en la pantalla “BATT” (Baterías descargadas), reemplace las
seis baterías.
● Es aconsejable que utilice baterías alcalinas.
● Existe un adaptador de CA opcional. (Modelo AD-30: 7 V, 1,2 A)
Nota:
●
●
Cuando reemplace las baterías, hágalo en tres minutos o menos.
De lo contrario, a menos que esté conectado un adaptador de
alimentación de CA opcional, se perderan todos los mensajes del
area de trabajo de la memoria de frases.
Tenga presente los detalles siguientes cuando se utilicen baterías de
NiCd en esta máquina.
(1) “BATT” no aparecerá en el visualizador cuando las baterías estén
débiles o gastadas. En lugar de ello, se desconectará la
alimentación.
(2) Incluso después de haber cargado las baterías, los caracteres
pueden no imprimirse con claridad como resultado de la baja
eficiencia de la carga o de las condiciones de operación.
-4-
CAMBIO DE LA CUCHILLA
Cuando la cuchilla no corte bien, reemplácela con una nueva.
Para reemplazar una cuchilla gastada o rota:
(1) Abra la cubierta del compartimiento del cassette de cinta y saque con
cuidado el cassette de cinta si estuviera instalada.
(2) Agarre la cuchilla entre los dedos y sáquela.
(3) Tome la cuchilla nueva con la lengüeta de la película protectora e inserte la
cuchilla en la máquina.
(4) Extraiga la película protectora de la cuchilla.
(5) Inserte el cassette de cinta, y cierre la cubierta del compartimiento de la
cassette de cinta.
ADVERTENCIA: Tenga mucho cuidado en no cortarse cuando reemplace la
cuchilla.
Nota:
La duración aproximada de la cuchilla del P-Touch es de unos 2000
cortes.
PRECAUCIÓN
• Cuando cambie la unidad de la cuchilla, cerciórese de no tocar la cuchilla de
la misma.
• Cerciórese de que los niños pequeños no intenten meter la unidad de la
cuchilla en su boca.
-5-
OPERACIONES DE LAS TECLAS
Tecla CODE
Manteniendo presionada la tecla CODE y pulsando la tecla adecuada, puede
utilizar las funciones indicadas en caracteres de color rosa o los caracteres de
color azul del de color azul de esta máquina.
Tecla SHIFT
Con la tecla SHIFT puede escribir mayúsculas, y símbolos de la parte superior de
las teclas. Para escribir una “A” mayúscula, mantenga presionada la tecla SHIFT
y pulse la tecla “A”. Para escribir un signo de porcentaje (que se encuentra en la
parte superior del “5”), Mantenga presionada la tecla SHIFT y pulse la tecla “5”.
Tecla CAPS
Manteniendo presionada la tecla CODE y pulsando la tecla CAPS, puede
conseguir que la máquina pase al modo de mayúsculas CAPS (Mayúsculas fijas/
Números).
Al acceder a este modo, el indicador CAPS en la pantalla se ilumina. En el modo
CAPS (Mayúsculas fijas/Números), puede escribir letras mayúsculas con sólo
pulsar las teclas de los caracteres. Si pulsa teclas de números, obtendrá números
y no los símbolos de la parte superior de las teclas, por tal razón el modo CAPS
es particularmente útil para crear mensajes que contengan números y
mayúsculas. Para abandonar el modo CAPS, mantenga presionada de nuevo la
tecla CODE y pulse la tecla CAPS.
Tecla ALT
Utilizando la tecla ALT, podrá escribir varios símbolos marcados con verde en las
teclas. Para escribir un símbolo que se encuentre en la parte derecha de una
tecla, mantenga presionada la tecla ALT y pulse la tecla en la que esté marcado
el símbolo deseado.
-6-
CREACION DE UN MENSAJE
PANTALLA
Una vez realizados los pasos anteriores ya puede proceder a la creación de un
mensaje en el de color azul máquina.
La pantalla LCD de la máquina tiene una capacidad de 4 caracteres. No
obstante, podrá crear mensajes con una longitud de hasta 55 caracteres. La
pantalla de 4 caracteres actúa como una ventana que se desplazase a lo largo del
mensaje.
1234567890123456789012345678901234567890123456789012345
DESPLAZAMIENTO DEL CURSOR
Puede volver a visualizar y editar una parte del mensaje desplazando el cursor
hacia adelante y hacia atrás.
Para desplazar el cursor a lo largo del mensaje:
Pulse las teclas
Nota:
●
●
y
y el cursor se desplazará de carácter en carácter.
Mantenga presionada la tecla CODE y la tecla TOP para devolver el
cursor al comienzo del mensaje.
Mantenga presionada la tecla CODE y pulse la tecla RELOC para
hacer que el cursor avance hasta el final del mensaje.
-7-
SIMBOLOS
Además de las letras, símbolos y números en la parte superior de las teclas,
existen 57 símbolos en el Modo Symbol. Estos 57 símbolos adicionales están
dispuestos en 15 grupos, correspondientes a los números del A al O del teclado.
N.˚ de
grupo
A
Ü
B
+
C
•
D
[ ]
E
1
_
2
F
ª
G
N.˚ de
grupo
SIMBOLOS
2
Æ
æ
×
÷
=
J



K
☞
°
º
3
§
♥
I
☞
2
SIMBOLOS
L
3
M
N
★
4
O
H
Para entrar un símbolo que no se encuentre en la parte superior de la tecla:
(1) Pulse la tecla CODE y la tecla SYMBOL para acceder al modo Symbol.
(2) En la pantalla podrá leer; “A-O?”.
(3) Pulse la tecla del número de A-O cuyo grupo contenga el símbolo que
desee. Se visualizará el grupo de símbolos de la letra.
(4) Desplace el cursor hasta el símbolo que desee elegir.
(5) Pulse la tecla SET.
Nota:
Presione la tecla DEL para abandonar el modo Symbol.
-8-
EDICION DE UN MENSAJE
Para borrar un carácter:
(1) Utilice las teclas del cursor para colocar éste un espacio a la derecha del
carácter que desea borrar.
(2) Presione la tecla DELETE.
Para borrar una palabra:
(1) Coloque el cursor un espacio a la derecha de la palabra que desee borrar.
(2) Mantenga presionada la tecla CODE y pulse la tecla WORD OUT.
Para reescribir un carácter:
(1) Mueva el cursor hasta el carácter que desea cambiar.
(2) Pulse la tecla correspondiente al carácter o símbolo deseado y el nuevo
carácter reemplazará al viejo en el mensaje.
Para insertar caracteres:
(1) Mantenga presionada la tecla CODE y pulse la tecla INSERT el número
deseado de veces hasta que aparezca en la pantalla “I: ”.
(2) Mueva el cursor un espacio hacia la derecha de la posición en la que desee
insertar un carácter.
(3) Pulse la tecla correspondiente al carácter o símbolo que desee añadir, o elija
un símbolo en el modo de símbolos. (Consulte SIMBOLOS.) Todos los
caracteres siguientes se moverán hacia la derecha al ser insertados.
Para abandonar el modo de inserción:
Mantenga presionada la tecla CODE y pulse la tecla INSERT dos veces.
-9-
TAMAÑO
Para elegir el tamaño de los caracteres:
Mantenga presionada la tecla CODE y pulse la tecla SIZE el número de veces
necesario hasta que en la pantalla se indique el tamaño de caracteres deseado.
Nota:
●
●
El tamaño de los caracteres que podrán imprimirse está limitado por
la anchura de la cinta.
Ancho de la cinta
Tamaños de caracteres posibles
3/4” (18 mm)
1, W2, H2, 4, 8, BIG
1/2” (12 mm)
1, W2, H2, 4, 8
3/8” (9 mm)
1, W2, H2, 4, 8
1/4” (6 mm)
1, W2
Si ajusta un tamaño de caracteres no mostrado en la tabla anterior y
pulsa la tecla PRINT, se visualizará un mensaje de error y no podrá
imprimirse la etiqueta.
-10-
1:Standard Size
W2:Double Width
H2:Double Height
4:Double Width & Double Height
8:4 × Width & Double Height
-11-
ESTILO
Para elegir un estilo de impresión:
Mantenga presionada la tecla CODE y pulse la tecla STYLE el número de veces
necesario hasta que en la pantalla aparezca el estilo de caracteres deseado. Si
selecciona un estilo que no sea NORMAL, en la pantalla aparecerá el indicador
de tal estilo.
Nota:
Solamente podrán imprimirse verticalmente caracteres de estilo
normal.
● La impresión vertical no podrá utilizarse con ciertas combinaciones
de anchura de cinta y tamaño de caracteres.
NORMAL (NORM)
ITALIC (ITAL)
●
OUTLINE (OUTL)
ITALIC+OUTLINE (IT + O)
BOLD (BOLD)
ITALIC+BOLD (IT + B)
SHADOW (SHAD)
ITALIC+SHADOW (IT + S)
VERTICAL (VERT)
-12-
SUBRAYADO/ENCUADRE
Para añadir un subrayado o un encuadre:
Mantenga presionada la tecla CODE y pulse la tecla UNDERLINE/FRAME
UNDL/FRM
#
3
el número de veces necesario hasta que en la pantalla aparezca el estilo
de subrayado/encuadre deseado. Cuando haya establecido el estilo de
subrayado/encuadre, el indicador correspondiente aparecerá en la pantalla.
Nota:
●
●
●
●
El subrayado y el encuadre no estarán disponibles simultaneamente.
La impresión con subrayado o encuadre está limitada por la anchura
de la cinta y el ajuste del tamaño de los caracteres.
El subrayado y el recuadre no podrán imprimirse cuado se usen
impresión vertical.
Ancho de la cinta
Tamaños de caracteres posibles
3/4” (18 mm)
1, W2, H2, 4, 8, BIG
1/2” (12 mm)
1, W2, H2, 4, 8
3/8” (9 mm)
1, W2, H2, 4, 8
1/4” (6 mm)
1, W2
Un subrayado o un encuadre no podrá imprimirse si el tamaño de
caracteres está ajustado a uno marcado con un X y está instalada la
cinta correspondiente.
BOX1:RECTANGLE
BOX3:POINTING
BOX2:SALE
BOX4:NAME PLATE
-13-
IMPRESION Y CORTE
Después de haber elegido el tamaño de los caracteres, el estilo de impresión, y el
juego tipográfico, podrá imprimir la etiqueta.
Para imprimir una etiqueta:
Pulse la tecla PRINT.
La etiqueta impresa saldrá por la ranura de salida de la cinta de la parte lateral de
la máquina.
Nota:
●
●
No tire de la cinta.
No intente cortar la cinta durante la impresión ni durante la alimentación de la misma.
Para cortar la cinta:
Extraiga la palanca de corte de la cinta de la parte lateral de la máquina.
Nota:
●
No extraiga demasiado la palanca de corte de la cinta, ya que podría
romperla.
Para pegar una etiqueta:
Despegue la cinta de la parte posterior y pegue la etiqueta en la posición
deseada.
-14-
IMPRESIÓN REPETIDA
Esta función le permitirá imprimir repetidamente la misma etiqueta hasta nueve
veces.
Para utilizar la función de impresión repetida :
Se recomienda ajustar el modo TAPE FEED a “#”, “##”, o “###”.
(1) Mantenga presionada la tecla CODE y pulse la tecla REPEAT (
W
REPEAT
).
(2) Introduzca el número de veces que desee imprimir la etiqueta.
(3) Pulse la tecla PRINT.
Si ha ajustado TAPE FEED a “#”, “##”, o “###”, pulse las teclas CODE + FEED
antes de cortar la cinta. El corte no se realiza automáticamente.
Nota:
●
●
●
●
CLEAR
DEL
Para volver a la pantalla anterior, pulse CLEAR (
) antes de
imprimir.
Antes de iniciar la impresión repetida, compruebe si hay suficiente
cinta en el cartucho.
Nunca trate de cortar la cinta durante la impresión.
Si la cinta se acaba antes de haber finalizado la impresión, pulse
inmediatamente la cinta ON/OFF. (Aparecerá una cinta con rayas.)
-15-
NUMERACIÓN
Esta función podrá utilizarse para que aumente automáticamente el número en
una serie de etiquetas impresas.
Para utilizar la función de cómputo automático :
Se recomienda ajustar el modo TAPE FEED a “#”, “##”, o “###”.
(1) Coloque el cursor debajo del número que desee aumentar.
(2) Mantenga presionada la tecla CODE y pulse la tecla NUMBER. La pantalla
solicitará la selección del último número a imprimir.
(3) Introduzca un número entre 1 y 9.
(4) Pulse PRINT. Las etiquetas se imprimirán y el número especificado
aumentará hasta llegar al último número.
Si ha ajustado TAPE FEED a “#”, “##”, o “###”, pulse las teclas CODE + FEED
antes de cortar la cinta. El corte no se realiza automáticamente.
Nota:
●
●
●
●
●
para borrar el número que haya introducido antes de la impresión,
pulse la tecla DELETE. Si vuelve a pulsar DELETE, saldrá del modo
de numeración (NUMBERING).
El último número a imprimirse tendrá que seleccionarse dentro del
margen 1-9.
Si introduce un número inferior al introducido originalmente en el
texto, la impresión se inhabilitará, y en la pantalla aparecerá el
mensaje “ERR” cuando pulse la tecla PRINT.
Los números aumentarán en uno cada vez.
Si las baterías se debilitan durante la operación de numeración
(NUMBERING), tal operación se interrumpirá.
-16-
IMPRESION INVERTIDA
Esta función imprimirá los caracteres de forma que podrán leerse desde el lado
adhesivo de la cinta. Con esta función hay que utilizar una cinta con adhesivo
transparente.
Mantenga pulsada la tecla CODE y presione la tecla MIRROR (
número de veces necesario hasta que en la pantalla aparezca “M:
PRINT
MIRROR
) el
”.
Para volver a la impresión normal, mantenga presionada la tecla CODE y pulse
la tecla MIRROR (
PRINT
MIRROR
pantalla aparezca “M:
Nota:
) el número de veces necesario hasta que en la
”.
La función de impresión invertida se desactivará cuando desconecte la
alimentación de la máquina. Si desea volver a utilizarla después de
haber desconectado la alimentación, tendrá que activarla.
-17-
AVANCE DE LA CINTA
Esta función podrá utilizarse para dejar márgenes iguales en la parte izquierda y
derecha de la etiqueta. Los márgenes podrán ajustarse a cuatro anchuras: 1/6” (4
mm), 2/3”(8 mm), 1/2”(12 mm), o 1”(24 mm), cuando la alimentación de la cinta
esté ajustada a “#”, “##”, “###”, o “####”, respectivamente. La cinta no se
alimentará automáticamente cuando esté ajustada a “-”. Cuando imprima
etiquetas continuamente, podrán imprimirse sin márgenes extra. Además, esta
función será muy útil para imprimir más de una etiqueta con múltiples estilos
cambiando el estilo cada vez que se imprima una etiqueta.
Para cambiar el modo de alimentación de cinta :
Mantenga presionada la tecla CODE y pulse la tecla TAPE el número de veces
necesario hasta que en la pantalla aparezca el modo de alimentación deseado.
Nota:
●
Cunando haya ajustado “####”, en la pantalla aparecerá el
indicador de cinta. El indicador de cinta no aparecerá cuando haya
ajustado “-”, “#”, “##”, ni “###”.
●
Cuando haya ajustado “-”, “#”, “##”, o “###”, pulse
SPACE
FEED
CODE
+
para alimentar la cinta después de que se haya impreso la
etiqueta y antes de cortar la cinta. Si no alimenta la cinta antes de
cortarla, es posible que se corten algunos de los caracteres impresos.
-18-
OPERACION DE LA MEMORIA DE FRASES
MEMORIA DE FRASES
Usted podrá utilizar la función de memoria de frases para almacenar sus
mensajes utilizados con más frecuencia. Estos mensajes no se borrarán con la
operación de borrado normal de mensajes (CODE + CLEAR).
En la memoria de frases podrá almacenar un total de 300 caracteres. Estos 300
caracteres podrán dividirse en un total de nueve áreas, y la capacidad máxima
de un área es de 55 caracteres.
Nota:
Cuando reemplace las baterías, hágalo en menos de tres minutos. De
lo contrario, a menos que esté conectado un adaptador de CA
opcional, se perderán los menajes del área de trabajo o de la memoria
de frases.
Para almacenar el mensaje actualmente visualizado en la memoria de frases :
(1) Mantenga presionada la tecla CODE y presione la tecla STORE. “1-9?”
aparecerá en la pantalla.
(2) Pulse una tecla del 1 al 9 para seleccionar un área de almacenamiento. Su
mensaje se almacenará en el área de la memoria seleccionada y el mensaje
previamente visualizado en el área de trabajo reaparecerá en la pantalla.
Si el área seleccionada ya está utilizándose, aparecerá un mensaje de error
brevemente, y después la pantalla le solicitará que elija un área. En tal caso,
seleccione un número diferente entre 1 y 9.
Para invocar un mensaje almacenado en la memoria de frases :
(1) Mantenga presionada la tecla CODE y pulse la tecla RECALL. “1-9?”
aparecerá en la pantalla.
(2) Pulse la tecla correspondiente al área que desee invocar. En la pantalla
aparecerán el número de la tecla y el comienzo del mensaje. Si ha
seleccionado un número erróneo, podrá presionar una nueva tecla numérica
para hacer que se visualice la frase correcta.
(3) Cuando se visualice el mensaje deseado, pulse la tecla SET. El mensaje
actualmente visualizado se borrará y el seleccionado se invocará en el área
de trabajo para su utilización.
-19-
Para borrar un área de la memoria de frases :
(1) Mantenga presionada la tecla CODE y pulse la tecla M.DEL. “1-9?”
aparecerá en la pantalla.
(2) Pulse la tecla correspondiente al área que desee borrar. En la pantalla
aparecerán el número de la tecla y el comienzo del mensaje. Si ha
seleccionado un número erróneo, podrá presionar una nueva tecla numérica
para hacer que se visualice la frase correcta.
(3) Cuando se visualice el mensaje deseado, pulse la tecla SET.
(4) El área de la memoria de frases se borrará y en la pantalla aparecerá el
mensaje previamente visualizado en el área de trabajo.
-20-
LISTA DE MENSAJES
ERR
Error de entrada. El tipo de cinta seleccionado es incorrecto.
BATT
Las baterías están débiles o gastadas.
FULL
Memoria llena (máximo 55 caracteres) o Memoria de
Frase llena (Consulte la página 19).
NORM
OUTL
BOLD
SHAD
ITAL
Consulte la página 12.
IT + O
IT + B
IT + S
VERT
A-O?
Consulte la página 8.
1-9?
Consulte la página 15, 16, 19 y 20.
BIG
La fuente del tamaño BIG está seleccionada.
####
–
#
Consulte página 18.
##
###
M:
Impresión en espejo
M:
Desactivación de la impresión en espejo
TEXT
Impresión sin subrayado/recuadro
UNDL
Subraya caracteres
BOX 1
BOX 2
BOX 3
Enmarca caracteres
BOX 4
I:
El modo de inserción está activado.
I:
El modo de inserción está desactivado.
-21-
ACCESORIOS
●
Suministros
Adquiera los cassetes de cinta, los adaptadores de CA y las cuchillas de cinta
en el distribuidor autorizado más cercano. Brother no asume ningún tipo de
responsabilidad por problemas causados por la utilización de suministros no
autorizados.
Utilice solamente cintas TZ Brother con esta máquina. No utilice cintas que
no tengan la marca
.
No. de
Stock
Descripción
Cantidad
/Paquete
Precio
1
1
1
1
1
1
1
1
1
1
1
1
$20.99
$20.99
$20.99
$20.99
$20.99
$24.99
$23.99
$20.99
$20.99
$23.99
$20.99
$20.99
1
$24.99
1
1
1
1
$20.99
$23.99
$23.99
$23.99
1
1
1
1
$16.99
$17.99
$17.99
$20.99
Cintas laminadas de 3/4” (18 mm)
TZ-141
TZ-145
TZ-241
TZ-242
TZ-243
TZ-344
TZ-345
TZ-441
TZ-541
TZ-545
TZ-641
TZ-741
Caracteres negros sobre cinta adhesiva transparente
Caracteres blancos sobre cinta adhesiva transparente
Caracteres negros sobre cinta adhesiva blanca
Caracteres rojos sobre cinta adhesiva blanca
Caracteres azules sobre cinta adhesiva blanca
Caracteres dorados sobre cinta adhesiva negra
Caracteres blancos sobre cinta adhesiva negra
Caracteres negros sobre cinta adhesiva roja
Caracteres negros sobre cinta adhesiva azul
Caracteres blancos sobre cinta adhesiva azul
Caracteres negros sobre cinta adhesiva amarilla
Caracteres negros sobre cinta adhesiva verde
Caracteres negros sobre cinta adhesiva naranja
TZ-B41
fluorescente
TZ-M41 Caracteres negros sobre cinta adhesiva mate
TZ-WB41 Caracteres negros sobre cinta Bugs bunny
TZ-WT41 Caracteres negros sobre cinta Taz
TZ-WS41 Caracteres negros sobre cinta Tweety & Sylvester
Cintas laminadas de 1/2” (12mm)
TZ-131
TZ-231
TZ-232
TZ-335
Caracteres negros sobre cinta adhesiva transparente
Caracteres negros sobre cinta adhesiva blanca
Caracteres rojos sobre cinta adhesiva blanca
Caracteres blancos sobre cinta adhesiva negra
-22-
No. de
Stock
Descripción
Cantidad
/Paquete
Precio
1
1
1
1
$14.99
$16.99
$18.99
$16.99
1
1
1
$12.99
$14.99
$17.99
Cantidad
/Paquete
Precio
1
$29.99
1
$24.99
Cantidad
/Paquete
Precio
1
$37.99
1
$24.99
Cantidad
/Paquete
Precio
1
1
$24.99
$9.99
Cintas laminadas de 3/8” (9mm)
TZ-121
TZ-221
TZ-325
TZ-421
Caracteres negros sobre cinta adhesiva transparente
Caracteres negros sobre cinta adhesiva blanca
Caracteres blancos sobre cinta adhesiva negra
Caracteres negros sobre cinta adhesiva roja
Cintas laminadas de 1/4” (6mm)
TZ-111
TZ-211
TZ-315
Caracteres negros sobre cinta adhesiva transparente
Caracteres negros sobre cinta adhesiva blanca
Caracteres blancos sobre cinta adhesiva negra
Cintas especiales
No. de
Stock
TZ-SE4
TZ-FA3
Descripción
Caracteres negros sobre cinta de seguridad
de 3/4” (18 mm)
Caracteres azules en cintra de tela de 1/2”
(12 mm) de anchura
Juego de estampas
No. de
Stock
SK-MB
SH-MB
Descripción
Juego de estampación para estampas medias
con tinta negra
Estampador adicional para estampas medias
con tinta negra
OPCIONES
No. de
Stock
AD-30
TC-9
Descripción
ADAPTADOR DE CA
CORTADOR DE CINTA
La mayor parte de tiendas y distribuidores tienen una línea completa de cintascassettes. Si desea hacer un pedido de accesorios para su P-Touch directamente a
Brother, tenga la amabilidad de consultar el “Formulario de pedido de accesorios”
o visítenos en línea en “http://www.brothermall.com”.
-23-
*NOTE*
• Please read this notice carefully before starting.
To insert a new tape cartridge
· REMOVE THE STOPPER.
Cutting tape
· DO NOT PULL TAPE TO ADVANCE IT.
· SOME TAPE CASSETTES ARE NOT
PROVIDED WITH A STOPPER.
· USE YOUR FINGER
TO TIGHTEN THE
RIBBON.
· INSTALL AND PRESS CODE+FEED.
· TO CUT TAPE,
USE THE BUILT-IN
CUTTER LEVER.
UNDER NO
CIRCUMSTANCES ATTEMPT TO CUT
THE TAPE
WHILE PRINTING
OR FEEDING.
AC adaptor connection
· USE THE AC ADAPTOR DESIGNED
EXCLUSIVELY FOR THIS MACHINE.
–
–
+
+
+
–
 BROTHER INDUSTRIES, LTD. 1995~
Printed in China
UN0166001