Specifications | Bryant 581B036--072 Air Conditioner User Manual

581B036--072
581C024--060
SINGLE--PACKAGE ROOFTOP HEATING/COOLING
STANDARD AND LOW NOx UNITS
Installation Instructions
TABLE OF CONTENTS
literature, tags and labels attached to the unit, and other safety
precautions that may apply.
Follow all safety codes. Wear safety glasses and work gloves. Use
quenching cloth for unbrazing operations. Have fire extinguishers
available for all brazing operations.
Recognize safety information. This is the safety--alert symbol
Page
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Step 1--Provide Unit Support . . . . . . . . . . . . . . . . . . . . . . . 2
ROOF CURB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. When you see this symbol on the unit and in instructions or
manuals, be alert to the potential for personal injury.
Understand the signal words DANGER, WARNING, and
CAUTION. These words are used with the safety--alert symbol.
DANGER identifies the most serious hazards which will result in
severe personal injury or death. WARNING signifies a hazard
which could result in personal injury or death. CAUTION is used
to identify unsafe practices which may result in minor personal
injury or product and property damage. NOTE is used to
highlight suggestions which will result in enhanced installation,
reliability, or operation.
SLAB MOUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ALTERNATE UNIT SUPPORT . . . . . . . . . . . . . . . . . 2
Step 2--Field Fabricate Ductwork . . . . . . . . . . . . . . . . . . . 2
Step 3--Install External Trap for Condensate Drain . . . . . . . 2
Step 4--Rig and Place Unit . . . . . . . . . . . . . . . . . . . . . . . . . 2
POSITIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Step 5 — Install Flue Hood . . . . . . . . . . . . . . . . . . . . . . . . 4
Step 6 — Install Gas Piping . . . . . . . . . . . . . . . . . . . . . . . . 4
!
Step 7 — Make Electrical Connections . . . . . . . . . . . . . . . . 8
FIELD POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . 8
WARNING
FIELD CONTROL WIRING . . . . . . . . . . . . . . . . . . . . 8
ELECTRICAL SHOCK HAZARD
HEAT ANTICIPATOR SETTINGS . . . . . . . . . . . . . . . 8
Failure to follow this warning could cause personal
injury or death.
Step 8 — Adjust Factory-Installed Options . . . . . . . . . . . 16
Before performing service or maintenance operations
on unit, turn off main power switch to unit and install
lockout tag. Ensure electrical service to rooftop unit
agrees with voltage and amperage listed on the unit
rating plate.
PERFECT HUMIDITY™ ADAPTIVE
DEHUMIDIFICATION SYSTEM . . . . . . . . . . . . . . 16
MANUAL OUTDOOR-AIR DAMPER . . . . . . . . . . 16
CONVENIENCE OUTLET . . . . . . . . . . . . . . . . . . . . 16
OPTIONAL ECONOMI$ER IV . . . . . . . . . . . . . . . . 18
!
ECONOMI$ER IV STANDARD SENSORS . . . . . . 19
ECONOMI$ER IV CONTROL MODES . . . . . . . . . 20
WARNING
FIRE, EXPLOSION HAZARD
Step 9 — Adjust Evaporator-Fan Speed . . . . . . . . . . . . . . 25
Failure to follow this warning could cause death and/or
property damage.
PRE--START--UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Disconnect gas piping from unit when leak testing at
pressure greater than 1/2 psig. Pressures greater than 1/2
psig will cause gas valve damage resulting in hazardous
condition. If gas valve is subjected to pressure greater
than 1/2 psig, it must be replaced before use. When
pressure testing field-supplied gas piping at pressures of
1/ psig or less, a unit connected to such piping must be
2
isolated by manually closing the gas valve(s).
START--UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
START--UP CHECKLIST . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
SAFETY CONSIDERATIONS
Installation and servicing of air-conditioning equipment can be
hazardous due to system pressure and electrical components.
Only trained and qualified service personnel should install, repair,
or service air-conditioning equipment.
Untrained personnel can perform basic maintenance functions of
cleaning coils and filters and replacing filters. All other operations
should be performed by trained service personnel. When working
on air-conditioning equipment, observe precautions in the
INSTALLATION
Unit is shipped in the vertical discharge configuration. To convert
to horizontal discharge application, remove duct opening covers.
Using the same screws, install covers on duct openings in
basepan of unit with insulation-side down. Seals around
openings must be tight. (See Fig. 1.)
1
A minimum clearance is not required around ductwork. Cabinet
return-air static pressure (a negative condition) shall not exceed
0.35 in. wg with economizer or 0.45 in. wg without economizer.
These units are designed for a minimum continuous return-air
temperature in heating of 50_F (dry bulb), or an intermittent
operation down to 45_F (dry bulb), such as when used with a
night setback thermostat.
To operate at lower return-air temperatures, a field-supplied
outdoor air temperature control must be used to initiate both
stages of heat when the temperature is below 45_F. Indoor
comfort may be compromised when these lower air temperatures
are used with insufficient heating temperature rise.
581B,C
Step 3 —Install External Trap for Condensate
Drain
Fig. 1 --- Horizontal Conversion Panels
The unit’s 3/4-in. condensate drain connections are located on the
bottom and side of the unit. Unit discharge connections do not
determine the use of drain connections; either drain connection
can be used with vertical or horizontal applications.
When using the standard side drain connection, ensure the plug
(Red) in the alternate bottom connection is tight before installing
the unit.
To use the bottom drain connection for a roof curb installation,
relocate the factory-installed plug (Red) from the bottom
connection to the side connection. The center drain plug looks
like a star connection, however it can be removed with a 1/2-in.
socket drive extension. (See Fig. 4.) The piping for the
condensate drain and external trap can be completed after the unit
is in place.
All units must have an external trap for condensate drainage.
Install a trap 4-in. deep and protect against freeze-up. If drain line
is installed downstream from the external trap, pitch the line away
from the unit at 1 in. per 10 ft of run. Do not use a pipe size
smaller than the unit connection (3/4 in.). (See Fig. 5.)
C06108
Step 1 —Provide Unit Support
Roof Curb
Assemble and install accessory roof curb in accordance with
instructions shipped with curb. (See Fig. 2.) Install insulation,
cant strips, roofing felt, and counter flashing as shown. Ductwork
must be attached to curb, not to the unit. If electric control power
or gas service is to be routed through the basepan, attach the
accessory thru-the-bottom service connections to the basepan in
accordance with the accessory installation instructions.
Connections must be installed before unit is set on roof curb.
IMPORTANT: The gasketing of the unit to the roof curb is
critical for a watertight seal. Install gasket supplied with the roof
curb as shown in Fig. 2. Improperly applied gasket can result in
air leaks and poor unit performance.
Curb should be level. Unit leveling tolerances are shown in Fig.
3. This is necessary for unit drain to function properly. Refer to
Accessory Roof Curb Installation Instructions for additional
information as required.
Slab Mount (Horizontal Units Only)
Provide a level concrete slab that extends a minimum of 6 in.
beyond unit cabinet. Install a gravel apron in front of
condenser-coil air inlet to prevent grass and foliage from
obstructing airflow.
NOTE: Horizontal units may be installed on a roof curb if
required.
Alternate Unit Support
When the curb or adapter cannot be used, support unit with
sleeper rails using unit curb or adapter support area. If sleeper
rails cannot be used, support the long sides of the unit with a
minimum of 3 equally spaced 4-in. x 4-in. pads on each side.
Step 4 —Rig and Place Unit
Inspect unit for transportation damage, and file any claim with
transportation agency. Keep unit upright and do not drop.
Spreader bars are not required if top crating is left on unit, and
rollers may be used to move unit across a roof. Level by using
unit frame as a reference. See Table 1 and 2 and Fig. 6 for
additional information. Operating weight is shown in Table 1 and
2 and Fig. 6.
Lifting holes are provided in base rails as shown in Fig. 8 and 9.
Refer to rigging instructions on unit.
!
WARNING
PROPERTY DAMAGE HAZARD
Failure to follow this warning could result in personal
injury, death and property damage.
Step 2 —Field Fabricate Ductwork
All panels must be in place when rigging and lifting.
Secure all ducts to roof curb and building structure on vertical
discharge units. Do not connect ductwork to unit. For horizontal
applications, field-supplied isolation flanges should be attached to
horizontal discharge openings and all ductwork should be secured
to the flanges. Insulate and weatherproof all external ductwork,
joints, and roof openings with counter flashing and mastic in
accordance with applicable codes.
Ducts passing through an unconditioned space must be insulated
and covered with a vapor barrier.
If a plenum return is used on a vertical unit, the return should be
ducted through the roof deck to comply with applicable fire
codes.
Positioning
Maintain clearance around and above unit to provide minimum
distance from combustible materials, proper airflow, and service
access. (See Fig. 7, 8 and 9.)
Position unit on roof curb so that the following clearances are
maintained: 1/4 in. clearance between the roof curb and the base
rail inside the front and rear, 0.0 in. clearance between the roof
curb and the base rail inside on the duct end of the unit. This will
result in the distance between the roof curb and the base rail
inside on the condenser end of the unit being approximately
equal to Fig. 2, section C-C.
Do not install unit in an indoor location. Do not locate unit air
inlets near exhaust vents or other sources of contaminated air.
2
CRBTMPWR001A01
CRBTMPWR002A01
CRBTMPWR003A01
CRBTMPWR004A01
B
1 -911 /16
[551]
C
1 -4
[406]
D ALT
DRAIN
HOLE
GAS
13/4
[44.5]
3/4
[19] NPT
1/2
[12.7] NPT
3/4
[19] NPT
POWER
[19] NPT
11/4 [31.7]
CONTROL
ROOF CURB
ACCESSORY
ACCESSORY
POWER
CRRFCURB001A01
3/4
3/4
[19] NPT
11/4
1/
2
[12.7]
CRRFCURB002A01
1/
2
[12.7]
A
1 -2
[356]
2 -0
[610]
UNIT
SIZE
581B036-072
581C024-060
NOTES:
1. Roof curb accessory is shipped disassembled.
2. Insulated panels.
3. Dimensions in [ ] are in millimeters.
4. Roof curb: galvanized steel.
5. Attach ductwork to curb (flanges of duct rest
on curb).
6. Service clearance: 4 ft on each side.
[31.7]
7.
Direction of airflow.
8. Connector packages CRBTMPWR001A01
and 002A01 are for thru-the-curb type gas.
Packages CRBTMPWR003A01 and 004A01
are for thru-the-bottom type gas connections.
581B,C
CONNECTOR
PKG. ACCY.
Fig. 2 --- Roof Curb Details
3
C06345
MAXIMUM ALLOWABLE
DIFFERENCE (in.)
A-B
0.5
B-C
1.0
A-C
1.0
CONDENSATE PAN (SIDE VIEW)
HORIZONTAL
DRAIN PLUG
DRAIN OUTLET
581B,C
NOTE: Drain plug is shown in factory-installed position.
Fig. 3 --- Unit Leveling Tolerances
Fig. 4 --- Condensate Drain Pan
C06110
Be sure that unit is installed such that snow will not block the
combustion intake or flue outlet.
Unit may be installed directly on wood flooring or on Class A, B,
or C roof-covering material when roof curb is used.
Although unit is weatherproof, guard against water from higher
level runoff and overhangs.
Locate mechanical draft system flue assembly at least 48 in. from
an adjacent building or combustible material. When unit is
located adjacent to public walkways, flue assembly must be at
least 7 ft above grade.
NOTE: When unit is equipped with an accessory flue discharge
deflector, allowable clearance is 18 inches.
Flue gas can deteriorate building materials. Orient unit such that
flue gas will not affect building materials.
Adequate combustion-air space must be provided for proper
operation of this equipment. Be sure that installation complies
with all local codes and Section 5.3, Air for Combustion and
Ventilation, NFGC (National Fuel Gas Code), ANSI (American
National Standards Institute) Z223.1-1984 and addendum
Z223.1a-1987. In Canada, installation must be in accordance with
the CAN1.B149.1 and CAN1.B149.2 installation codes for gas
burning appliances.
Flue vent discharge must have a minimum horizontal clearance of
4 ft from electric and gas meters, gas regulators, and gas relief
equipment.
After unit is in position, remove shipping materials and rigging
skids.
C06003
NOTE: Trap should be deep enough to offset maximum unit static
difference. A 4-in. trap is recommended.
Fig. 5 --- Condensate Drain Piping Details
C06004
Step 6 —Install Gas Piping
Unit is equipped for use with type of gas shown on nameplate.
Refer to local
building codes, or in the absence of local codes,
to ANSI Z223.1-1984 and addendum Z223.1A-1987 entitled
National Fuel Gas Code. In Canada, installation must be in
accordance with the CAN1.B149.1 and CAN1.B149.2
installation codes for gas burning appliances.
For natural gas applications, gas pressure at unit gas connection
must not be less than 4 in. wg or greater than 13 in. wg while the
unit is operating. On 581B036--072 and 581C036--060 high-heat
units, the gas pressure at unit gas connection must not be less than
5 in. wg or greater than 13 in. wg while the unit is operating. For
propane applications, the gas pressure must not be less than 5 in.
wg or greater than 13 in. wg at the unit connection.
Size gas supply piping for 0.5 in. wg maximum pressure drop.
Do not use supply pipe smaller than unit gas connection.
Step 5 —Install Flue Hood
Flue hood is shipped screwed to the burner compartment access
panel. Remove from shipping location and, using screws
provided, install flue hood in location shown in Fig. 8 and 9.
For units being installed in California Air Quality Management
Districts which require NOx emissions of 40 nanograms/joule or
less, a low NOx unit must be installed.
NOTE: Low NOx units are available for 2 to 5 ton units.
4
C06111
Fig. 6 --- Rigging Details
UNIT
581C
024
036
048
060
UNIT
581B
036
048
060
072
OPERATING
WEIGHT
lb
kg
530
240
540
245
560
254
635
288
OPERATING
WEIGHT
lb
530
540
560
635
kg
240
245
254
288
“A”
in.
73.69
73.69
73.69
73.69
mm
1872
1872
1872
1872
“A”
in.
73.69
73.69
73.69
73.69
mm
1872
1872
1872
1872
DIMENSIONS
“B”
in.
mm
35.50
902
35.50
902
35.50
902
35.50
902
DIMENSIONS
“B”
in.
mm
35.50
902
35.50
902
35.50
902
35.50
902
!
“C”
in.
33.31
33.31
33.31
41.31
mm
847
847
847
1050
“C”
in.
33.31
33.31
33.31
41.31
mm
847
847
847
1050
WARNING
PROPERTY DAMAGE HAZARD
Failure to follow this warning could result in personal
injury, death and property damage.
All panels must be in place when rigging and lifting.
See Fig. 11 for typical pipe guide and locations of external
manual gas shutoff valve.
NOTE: If accessory thru-the-bottom connections and roof curb
are used, refer to the Thru-the-Bottom Accessory Installation
Instructions for information on power wiring and gas
connection piping. The power wiring, control wiring and gas
piping can be routed through field-drilled holes in the basepan.
The basepan is specially designed and dimpled for drilling the
access connection holes.
Fig. 7 --- Roof Curb Alignment
C06208
!
Support gas piping as shown in the table in Fig. 11. For example,
a 3/4-in. gas pipe must have one field-fabricated support beam
every 8 ft. Therefore, an 18-ft long gas pipe would have a
minimum of 3 support beams, and a 48-ft long pipe would have a
minimum of 6 support beams.
WARNING
FIRE, EXPLOSION HAZARD
Failure to follow this warning could result in personal
injury, death and/or property damage.
When connecting the gas line to the unit gas valve, the
installer MUST use a backup wrench to prevent damage
to the valve.
5
581B,C
NOTES:
1. Place unit on curb as close as possible to the duct end.
2. Dimension in ( ) is in millimeters.
3. Hook rigging shackles through holes in base rail as shown in detail “A.” Holes in base rails are centered around the unit center of gravity. Use wooden top skid
when rigging to prevent rigging straps from damaging unit.
4. Weights include base unit without economizer. See Table 1 for unit operating weights with accessory economizer.
5. Weights include base unit without the Perfect Humidityt adaptive dehumidification system. See Table 1 for unit operating weights with the Perfect Humidityt
system.
6
Fig. 8 --- 581B 036--072 Base Unit Dimensions
CONTROL BOX
COMPRESSOR
ACCESS PANEL
581B,C
C06363
7
Fig. 9 --- 581C 024--060 Base Unit Dimensions
COMPRESSOR
ACCESS PANEL
581B,C
C06364
C06114
581B,C
Fig. 10 --- Flue Hood Details
Field Power Supply
All units except 208/230-v units are factory wired for the voltage
shown on the nameplate. If the 208/230-v unit is to be connected
to a 208-v power supply, the transformer must be rewired by
moving the black wire from the 230-v terminal on the
transformer and connecting it to the 200-v terminal from the
transformer.
Refer to unit label diagram for additional information. Pigtails
are provided for field service. Use factory-supplied splices or UL
(Underwriters’ Laboratories) approved copper connector.
When installing units, provide a disconnect per NEC.
All field wiring must comply with NEC and local
requirements.
Install conduit through side panel openings indicated in Fig. 8.
Route power lines through connector to terminal connections as
shown in Fig. 12.
Voltage to compressor terminals during operation must be within
voltage range indicated on unit nameplate (also see Tables 3 and
4). On 3-phase units, voltages between phases must be balanced
within 2% and the current within 10%. Use the formula shown in
Tables 3 and 4, Note 3 to determine the percent voltage
imbalance. Operation on improper line voltage or excessive phase
imbalance constitutes abuse and may cause damage to electrical
components. Such operation would invalidate any applicable
Bryant warranty.
NOTE: If accessory thru-the-bottom connections and roof curb
are used, refer to the Thru-the-Bottom Accessory Installation
Instructions for information on power wiring and gas connection
piping. The power wiring, control wiring and gas piping can be
routed through field-drilled holes in the basepan. The basepan is
specially designed and dimpled for drilling the access connection
holes. (See Fig. 2.)
Field Control Wiring
Install a Bryant-approved accessory thermostat assembly
according to installation instructions included with the accessory.
Locate thermostat assembly on a solid wall in the conditioned
space to sense average temperature in accordance with thermostat
installation instructions.
Route thermostat cable or equivalent single leads of colored wire
from subbase terminals through connector on unit to low-voltage
connections (shown in Fig. 13 and 14).
Connect thermostat wires to matching screw terminals of
low-voltage connection board. (See Fig. 13 and 14.)
NOTE: For wire runs up to 50 ft, use no. 18 AWG (American
Wire Gauge) insulated wire (35_C minimum). For 50 to 75 ft, use
no. 16 AWG insulated wire (35_C minimum). For over 75 ft, use
no. 14 AWG insulated wire (35_C minimum). All wire larger
than no. 18 AWG cannot be directly connected to the thermostat
and will require a junction box and splice at the thermostat.
Pass the control wires through the hole provided in the corner
post; then feed wires through the raceway built into the corner
post to the 24-v barrier located on the left side of the control box.
(See Fig. 15). The raceway provides the UL required clearance
between high and low-voltage wiring.
Heat Anticipator Settings
Set heat anticipator settings at 0.14 amp for first stage and 0.14
for second stage heating, when available.
LEGEND
NFGC — National Fuel Gas Code
*Field supplied.
NOTE: Follow all local codes.
SPACING OF SUPPORTS
STEEL PIPE
NOMINAL DIAMETER (in.)
1/
2
3/4 or 1
11/4 or larger
SPACING OF SUPPORTS
X DIMENSION (ft)
6
8
10
Fig. 11 --- Gas Piping Guide (With Accessory
Thru--the--Curb Service Connections)
C06115
Step 7 —Make Electrical Connections
!
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal
injury or death.
Unit cabinet must have an uninterrupted, unbroken
electrical ground to minimize the possibility of personal
injury if an electrical fault should occur. This ground
may consist of electrical wire connected to unit ground
lug in control compartment, or conduit approved for
electrical ground when installed in accordance with
NEC (National Electrical Code), ANSI/NFPA (National
Fire Protection Association), latest edition, and local
electrical codes. Do not use gas piping as an electrical
ground.
8
BASE UNIT 581B
NOMINAL CAPACITY (tons)
OPERATING WEIGHT (lb)
Unit
Perfect Humidity™ Adaptive Dehumidification System
EconoMi$er IV
Roof Curb
COMPRESSOR
Quantity
Oil (oz)
REFRIGERANT TYPE
Expansion Device
Operating Charge (lb-oz)
Standard Unit
Unit With Perfect Humidity Adaptive Dehumidification System
CONDENSER FAN
Quantity...Diameter (in.)
Nominal Cfm
Motor Hp...Rpm
Watts Input (Total)
CONDENSER COIL
Rows...Fins/in.
Total Face Area (sq ft)
EVAPORATOR COIL
Standard Unit
Rows...Fins/in.
Total Face Area (sq ft)
Unit with Perfect Humidity Adaptive Dehumidification System
Rows...Fins/in.
Total Face Area (sq ft)
EVAPORATOR FAN
Quantity...Size (in.)
Nominal Cfm
Maximum Continuous Bhp
Std
Hi-Static
Motor RPM
Std
Hi-Static
Motor Frame Size
Std
Hi-Static
Fan Rpm Range
Std
Hi-Static
Motor Bearing Type
Maximum Fan Rpm
Std
Motor Pulley Pitch Diameter A/B (in.)
Hi-Static
Nominal Motor Shaft Diameter (in.)
Std
Hi-Static
Fan Pulley Pitch Diameter (in.)
Std
Hi-Static
Belt — Type...Length (in.)
Std
Hi-Static
Pulley Center Line Distance (in.)
Std
Speed Change per Full Turn of
Movable Pulley Flange (rpm)
Hi-Static
Std
Movable Pulley Maximum Full
Turns from Closed Position
Hi-Static
Factory Setting — Full Turns Open
Std
Hi-Static
Factory Speed Setting (rpm)
Std
Hi-Static
Fan Shaft Diameter at Pulley (in.)
036
3
048
4
060
5
072
6
530
15
50
115
540
23
50
115
560
25
50
115
635
29
50
115
1
42
1
53
1
50
1
60
10-2
18-8
10-0
20-5
12- 8
23-14
2...15
5.5
4...15
5.5
4...15
7.3
Scroll
R-22
Acutrol™ Metering Device
5-8
12-5
Propeller
1...22
1...22
1...22
3500
4100
4100
1/ ...825
1/ ...1100
1/ ...1100
4
4
4
180
320
320
3/8 ---in. OD Enhanced Copper Tubes, Aluminum Lanced Fins
1...17
2...17
2...17
2...17
14.6
16.5
16.5
21.3
3/8 ---in. OD Enhanced Copper Tubes, Aluminum Double-Wavy Fins
1...22
3500
1/ ...825
4
180
2...15
5.5
1...17
3.9
2...17
2...17
3.9
3.9
Centrifugal Type, Belt Drive
1...10 x 10
1...10 x 10
1600
2000
1.20
1.30/2.40*
2.40
2.90
1620
1725
1725
1725
48
48/56*
56
56
770-1185
1035-1460
1075-1455
1300-1685
Ball
Ball
2100
2100
1.9/2.0
2.4/3.4
2.8/3.8
3.4/4.4
1/
5/
2
8
5/
5/
8
8
4.0
4.0
4.0
4.5
1...A...36
1....4...40
1...A...39
1...A...40
10.0-12.4
14.7-15.5
70
75
65
60
5
6
6
5
3
3
31/2
31/2
936
1248
1233
1396
5/
5/
8
8
1...10 x 10
1200
1.20
2.40
1620
1725
48
56
680-1044
1075-1455
Ball
2100
1.9/2.9
2.8/3.8
1/
2
5/
8
4.5
4.5
1...A...36
1...A...39
10.0-12.4
65
65
5
6
3
31/2
826
1233
5/
8
LEGEND
Bhp — Brake Horsepower
9
2...17
5.2
1...10 x 10
2400
2.40
2.90
1725
1725
56
56
1119-1585
1300-1685
Ball
2100
2.4/3.4
3.4/3.4
5/
8
7/
8
4.0
4.5
1...A...38
1...A...40
14.7-15.5
95
60
5
5
3
31/2
1305
1396
5/
8
581B,C
Table 1—Physical Data 581B
Table 1 — Physical Data 581B (cont)
UNIT SIZE 581B
FURNACE SECTION
Rollout Switch Cutout Temp (F)†
Burner Orifice Diameter (in. ...drill size)**
Natural Gas —Std
581B,C
Propane —Alt††
Thermostat Heat Anticipator Setting (amps)
208/230/460 v
First Stage
Second Stage
Gas Input (Btuh)
First Stage/Second Stage (3 ---phase units)
Efficiency (Steady State) (%)
Temperature Rise Range
Manifold Pressure (in. wg)
Natural Gas —Std
Propane —Alt††
Maximum Static Pressure (in. wg)
Field Gas Connection Size (in.)
HIGH-PRESSURE SWITCH (psig)
Standard Compressor Internal Relief
Cutout
Reset (Auto.)
LOSS-OF-CHARGE SWITCH/LOW-PRESSURE
(Liquid Line) (psig)
Cutout
Reset (Auto.)
FREEZE PROTECTION THERMOSTAT
Opens (F)
Closes (F)
OUTDOOR-AIR INLET SCREENS
RETURN-AIR FILTERS
Quantity...Size (in.)
036
048
060
072
195
195
195
195
.113...33
.113...33
—
.102...38
.102...38
—
.089...43
.089...43
—
.082...45
.082...45
—
.113...33
.113...33
.129...30
.102...38
.102...38
.116...32
.089...43
.089...43
.102...38
.082...45
.082...45
.094...42
.113...33
.113...33
.129...30
.102...38
.102...38
.116...32
.089...43
.089...43
.102...38
.082...45
.082...45
.094...42
.113...33
.113...33
.129...30
—
—
—
.089...43
.089...43
.104...39
—
—
—
.14
.14
.14
.14
.14
.14
.14
.14
50,000/ 72,000
82,000/115,000
—
—/72,000
—/115,000
—
—/ 60,000
—/ 90,000
—
82
80
—
82
80
—
80
80
—
15 ---45
55 ---85
—
15 ---45
55 ---85
—
20 ---50
30 ---60
—
50,000/ 72,000
82,000/115,000
120,000/150,000
—/72,000
—/115,000
—/150,000
—/60,000
—/90,000
—/120,000
82
81
80
82
81
80
80
80
80
15 ---45
35 ---65
50 ---80
15 ---45
35 ---65
50 ---80
20 ---50
30 ---60
40 ---70
50,000/ 72,000
82,000/115,000
120,000/150,000
—/72,000
—/115,000
—/150,000
—/60,000
—/90,000
—/120,000
82
81
80
82
81
80
80
80
80
15 ---45
35 ---65
50 ---80
15 ---45
35 ---65
50 ---80
20 ---50
30 ---60
40 ---70
50,000/ 72,000
82,000/115,000
120,000/150,000
—
—
—
—
—
—
82
81
80
—
—
—
—
—
—
15 ---45
35 ---65
50 ---80
—
—
—
—
—
—
3.5
3.5
1.0
1/2
3.5
3.5
1.0
1/2
3.5
3.5
1.0
1/2
3.5
3.5
1.0
1/2
071/072
114/115
149/150
060N
090N
120N
071/072
114115
149/150
060N
090N
120N
072
115
150
071II
114II
149II
060N***
090N***
120N***
072
115
150
071
114
149
060N
090N
120N
072
115
150
071
114
149
060N
090N
120N
450 ± 50
428
320
7±3
22 ± 5
30 ± 5
45 ± 5
Cleanable. Screen quantity and size varies with option selected.
Throwaway
2...16 x 25 x 2
4...16 x 16 x 2
LEGEND
Bhp — Brake Horsepower
**60,000 and 72,000 Btuh heat input units have 2 burners. 90,000 and 120,000 Btuh
heat input units have 3 burners. 115,000 Btuh heat input units and 150,000 Btuh
Heat input units have 3 burners.
††A propane kit is available as an accessory. Kit may be used at elevations as high as
2000 ft. If a propane kit is used with Low NOx units, the Low NOx baffle must be
removed and the units will no longer be classified as Low NOx units.
ll Three-phase standard models have heating inputs as shown. Single-phase standard models have one-stage heating with heating input values.
***California compliant three-phase models.
†††California SCAQMD compliant low NOx models have combustion products that are
controlled to 40 nanograms per joule or less.
10
Table 2—Physical Data 581C
024
2
036
3
530
13
50
115
540
15
50
115
1
25
1
42
5 ---3
10 ---2
7 ---11
14 ---0
1...22
3000
1/8...825
180
1...17
14.6
2...15
5.5
1...17
3.5
1...17
3.9
1...10 x 10
800
0.58
1...10 x 10
1200
1.20
2.40
48
56
1620
680-1044
1075-1455
Ball
2100
1.9/2.9
2.8/3.8
48
1620
400-1000
Ball
1620
2.4/3.2
7/
1/
2
5/
8
8
8
4.5
4.5
1...A...36
1...A...39
10.0-12.4
65
65
5
6
3
31/2
826
1233
5/
8
4.0
4.5
1...A...36
10.0 ---12.4
60
5
3
756
5/
560
23
50
115
Scroll
1
56
R-22
Acutrol™ Metering Device
072
5
635
25
50
115
1
53
8 ---8
12 ---11
14 ---13
21 ---0
Propeller
1...22
1...22
1...22
3500
3500
4100
1/8...825
1/8...825
1/ ...1100
4
180
180
320
3/8 ---in. OD Enhanced Copper Tubes, Aluminum Lanced Fins
1...17
2...17
2...17
14.6
16.5
16.5
3/8 ---in. OD Enhanced Copper Tubes, Aluminum Double-Wavy Fins
2...15
4.2
5/
048
4
8
11
2...15
5.5
2...17
3.9
Centrifugal Type, Belt Drive
1...10 x 10
1600
1.20
2.40
48
56
1620
770-1185
1075-1455
Ball
2100
1.9/2.0
2.8/3.8
1/
2
5/
8
4.0
4.0
1...A...36
1...A...39
10.0-12.4
70
65
5
6
3
31/2
936
1233
5/
8
4...15
5.5
2...17
3.9
1...10 x 10
2000
1.30/2.40*
2.90
48/56*
56
1725
1035-1460
1300-1685
Ball
2100
2.4/3.4
3.4/4.4
5/
8
5/
8
4.0
4.5
1....4...40
1...A...40
14.7-15.5
75
60
6
5
3
31/2
1248
1396
5/
8
581B,C
BASE UNIT 581C
NOMINAL CAPACITY (tons)
OPERATING WEIGHT (lb)
Unit
Perfect Humidity™ Adaptive Dehumidification System
EconoMi$er IV
Roof Curb
COMPRESSOR
Quantity
Oil (oz)
REFRIGERANT TYPE
Expansion Device
Operating Charge (lb-oz)
Standard Unit
Unit With Perfect Humidity Adaptive Dehumidification System
CONDENSER FAN
Quantity...Diameter (in.)
Nominal Cfm
Motor Hp...Rpm
Watts Input (Total)
CONDENSER COIL
Rows...Fins/in.
Total Face Area (sq ft)
EVAPORATOR COIL
Standard Unit
Rows...Fins/in.
Total Face Area (sq ft)
Unit with Perfect Humidity Adaptive Dehumidification System
Rows...Fins/in.
Total Face Area (sq ft)
EVAPORATOR FAN
Quantity...Size (in.)
Nominal Cfm
Maximum Continuous Bhp
Std
Hi-Static
Motor Frame Size
Std
Hi-Static
Motor Rpm
Fan Rpm Range
Std
Hi-Static
Motor Bearing Type
Maximum Fan Rpm
Std
Motor Pulley Pitch Diameter A/B (in.)
Hi-Static
Nominal Motor Shaft Diameter (in.)
Std
Hi-Static
Fan Pulley Pitch Diameter (in.)
Std
Hi-Static
Belt — Type...Length (in.)
Std
Hi-Static
Pulley Center Line Distance (in.)
Std
Speed Change per Full Turn of
Movable Pulley Flange (rpm)
Hi-Static
Std
Movable Pulley Maximum Full
Turns from Closed Position
Hi-Static
Factory Setting — Full Turns Open
Std
Hi-Static
Factory Speed Setting (rpm)
Std
Hi-Static
Fan Shaft Diameter at Pulley (in.)
Table 2 — Physical Data 581C (cont)
UNIT SIZE 581C
FURNACE SECTION
Rollout Switch Cutout Temp (F)†
Burner Orifice Diameter (in. ...drill size)**
Natural Gas —Std
581B,C
Propane —Alt††
Thermostat Heat Anticipator Setting (amps)
208/230/460 v
First Stage
Second Stage
Gas Input (Btuh)
First Stage/Second Stage (3 ---phase units)
Efficiency (Steady State) (%)
Temperature Rise Range
Manifold Pressure (in. wg)
Natural Gas —Std
Propane —Alt††
Maximum Static Pressure (in. wg)
Field Gas Connection Size (in.)
HIGH-PRESSURE SWITCH (psig)
Standard Compressor Internal Relief
Cutout
Reset (Auto.)
LOSS-OF-CHARGE SWITCH/LOW-PRESSURE
(Liquid Line) (psig)
Cutout
Reset (Auto.)
FREEZE PROTECTION THERMOSTAT
Opens (F)
Closes (F)
OUTDOOR-AIR INLET SCREENS
RETURN-AIR FILTERS
Quantity...Size (in.)
024
036
048
060
195
195
195
195
.113...33
.113...33
—
.102...38
.102...38
—
.089...43
.089...43
—
.082...45
.082...45
—
.113...33
.113...33
.129...30
.102...38
.102...38
.116...32
.089...43
.089...43
.102...38
.082...45
.082...45
.094...42
.113...33
.113...33
.129...30
.102...38
.102...38
.116...32
.089...43
.089...43
.102...38
.082...45
.082...45
.094...42
.113...33
.113...33
.129...30
—
—
—
.089...43
.089...43
.104...39
—
—
—
.14
.14
.14
.14
.14
.14
.14
.14
50,000/ 72,000
82,000/115,000
—
—/72,000
—/115,000
—
—/ 60,000
—/ 90,000
—
82
80
—
82
80
—
80
80
—
15 ---45
55 ---85
—
15 ---45
55 ---85
—
20 ---50
30 ---60
—
50,000/ 72,000
82,000/115,000
120,000/150,000
—/72,000
—/115,000
—/150,000
—/60,000
—/90,000
—/120,000
82
81
80
82
81
80
80
80
80
15 ---45
35 ---65
50 ---80
15 ---45
35 ---65
50 ---80
20 ---50
30 ---60
40 ---70
50,000/ 72,000
82,000/115,000
120,000/150,000
—/72,000
—/115,000
—/150,000
—/60,000
—/90,000
—/120,000
82
81
80
82
81
80
80
80
80
15 ---45
35 ---65
50 ---80
15 ---45
35 ---65
50 ---80
20 ---50
30 ---60
40 ---70
50,000/ 72,000
82,000/115,000
120,000/150,000
—
—
—
—
—
—
82
81
80
—
—
—
—
—
—
15 ---45
35 ---65
50 ---80
—
—
—
—
—
—
3.5
3.5
1.0
1/2
3.5
3.5
1.0
1/2
3.5
3.5
1.0
1/2
3.5
3.5
1.0
1/2
071/072
114/115
149/150
060N
090N
120N
071/072
114115
149/150
060N
090N
120N
072
115
150
071II
114II
149II
060N***
090N***
120N***
072
115
150
071
114
149
060N
090N
120N
072
115
150
071
114
149
060N
090N
120N
LEGEND
Bhp — Brake Horsepower
**60,000 and 72,000 Btuh heat input units have 2 burners. 90,000 and 120,000 Btuh
heat input units have 3 burners. 115,000 Btuh heat input units and 150,000 Btuh
Heat input units have 3 burners.
††A propane kit is available as an accessory. Kit may be used at elevations as high as
2000 ft. If a propane kit is used with Low NOx units, the Low NOx baffle must be
450 ± 50
428
320
7±3
22 ± 5
30 ± 5
45 ± 5
Cleanable. Screen quantity and size varies with option selected.
Throwaway
2...16 x 25 x 2
4...16 x 16 x 2
removed and the units will no longer be classified as Low NOx units.
ll Three-phase standard models have heating inputs as shown. Single-phase standard models have one-stage heating with heating input values.
***California compliant three-phase models.
†††California SCAQMD compliant low NOx models have combustion products that are
controlled to 40 nanograms per joule or less.
12
11
23
11
YEL
YEL
23
BLK
BLU
11
C
C
21
TO COMP
BLK
BLK
21
23
23
YEL
TO COMP
BLU
C
23
21
23
EQUIP
GND
FIELD POWER SUPPLY
FIELD POWER SUPPLY
208/230-3-60
480-3-60
(SIZES 581B036,048
581C036,048)
DISCONNECT
PER NEC
TO COMP
BLK
11
23
BLK
11
YEL
C
21
DISCONNECT
PER NEC
13
YEL
DISCONNECT
PER NEC
TO TB2
581B,C
FIELD POWER SUPPLY
208/230-1-60
(SIZES 581B036-060,
581C024-060)
575-3-60
(SIZES 581B036,048
581C036,048)
BLU
C
BLU
23
21
1
23
4
IFC
3
6
FIELD POWER SUPPLY
575-3-60
(SIZES 581B060, 072)
FIELD POWER SUPPLY
208/230-3-60
460-3-60
DISCONNECT
PER NEC
(SIZES 581B060, 072,
581C0060)
DISCONNECT
PER NEC
C06346
Fig. 12 --- Power Wiring Connections
COOL STAGE 1
Y1/W2
R
FAN
G
G
HEAT STAGE 1
W/W1
Y1
COOL STAGE 2
Y/Y2
Y2
HEAT STAGE 2
O/W2
W1
24 VAC HOT
R
W2
24 VAC COM
C
N/A
OUTDOOR AIR
S1
SENSOR
S2
LOW VOLTAGE
CONNECTIONS
INTEGRATED GAS UNIT
CONTROLLER (IGC)
WIRE
CONNECTIONS
TO
LOW-VOLTAGE
SECTION
C
IPD/X
THERMOSTAT DIPSWITCH SETTINGS
ON
OFF
D
B
A
C
LEGEND
Field Wiring
NOTE: Underlined letter indicates active thermostat output when
configured for A/C operation.
Fig. 13 --- Low--Voltage Connections With or
Without Economizer or Two--Position Damper
C06008
Fig. 14 --- Field Control Wiring
13
C06125
14
575---3---60
460---3---60
208/230---3---60
208/230---1---60
575---3---60
460---3---60
208/230---3---60
208/230---1---60
575---3---60
460---3---60
HS
Perfect
Humidity
HS
STD
HS
STD
HS
STD
STD
Perfect
Humidity
HS
STD
HS
STD
HS
STD
STD
Perfect
Humidity
HS
STD
518
414
187
187
518
414
187
197
518
414
187
187
187
Min
632
508
254
254
632
508
254
254
632
508
254
254
254
Max
VOLTAGE
RANGE
1
1
1
1
1
1
1
1
1
1
1
1
1
QTY
71
7.1
84
8.4
17 3
17.3
25
61
6.1
71
7.1
14 1
14.1
21
42
4.2
51
5.1
10 3
10.3
16
10 9
10.9
RLA
COMPRESSOR
53
70
123
150
38
45
95
115
31
39
77
88
63
LRA
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
QTY
OFM
1 9†
1.9†
06
0.6
08
0.8
15
1.5
15
1.5
0 8†
0.8†
06
0.6
08
0.8
15
1.5
15
1.5
0 4†
0.4†
04
0.4
04
0.4
07
0.7
07
0.7
07
0.7
FLA
0 3†
0.3†
0 3†
0.3†
06
0.6
06
0.6
0 3†
0.3†
03
0.3
06
0.6
06
0.6
0 3†
0.3†
03
0.3
06
0.6
06
0.6
06
0.6
FLA
COMBUSTION
FAN MOTOR
Table 3—Electrical Data 581C
NOTES:
* The values listed in this table do not include power exhaust. See power exhaust table for power exhaust requirements.
** Fuse or HACR breaker
{ 460v motor
FLA ---Full Load Amps
HACR --- Heating, Air Conditioning and Refrigeration
IFM --- Indoor (Evaporator) Fan Motor
LRA --- Locked Rotor Amps
MCA --- Minimum Circuit Amps
MOCP --- Maximum Overcurrent Protection
NEC --- National Electrical Code
OFM --- Outdoor (Condenser) Fan Motor
RLA --- Rated Load Amps
060
(5 tons)
048
(4 tons)
036
(3 tons)
STD
HS
STD
STD
208/230---1---60
024
(2 tons)
208/230---3---60
STD
208/230---1---60
UNIT SIZE
IFM TYPE
NOMINAL
V---PH---Hz
581C024--- 060
3 4†
3.4†
28
2.8
20
2.0
34
3.4
26
2.6
75
7.5
58
5.8
66
6.6
2 6†
2.6†
20
2.0
19
1.9
26
2.6
22
2.2
58
5.8
49
4.9
49
4.9
2 6†
2.6†
20
2.0
19
1.9
26
2.6
22
2.2
58
5.8
49
4.9
49
4.9
20
2.0
IFM
FLA
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
CONV
OUTLET
*
MOCP**
16.3
22.3
25.6
31.6
18.5
24.5
19.4
25.4
9.0
11.7
9.4
12.1
7.6
9.7
7.7
9.8
7.7
9.8
32.7
38.7
24.0
30.0
24.9
30.9
11.9
14.6
12.3
15.0
10.1
12.3
10.2
12.4
10.3
12.5
39.4
45.4
28.9
34.9
30.6
36.6
13.9
16.6
14.7
17.4
11.5
13.6
12.3
14.4
12.2
14.4
MCA
20
25
30
35
25
30
25
30
15
15
15
15
10
15
10
15
10
15
40
45
30
35
30
35
15
20
15
20
15
15
15
15
15
15
50
60
35
40
35
40
20
20
20
20
15
15
15
20
15
20
POWER SUPPLY
581B,C
15.6
21.2
24.8
30.4
18.3
23.8
19.3
24.9
8.9
11.4
9.3
11.8
7.5
9.5
7.6
9.6
8.0
9.6
31.5
37.0
23.6
29.1
24.6
30.1
11.6
14.1
12.1
14.6
9.9
11.9
10.0
12.0
10.1
12.1
38.1
43.6
28.3
33.8
30.2
35.8
13.6
16.1
14.5
17.0
11.2
13.2
12.1
14.1
12.0
14.0
FLA
69
73
101
106
90
95
120
124
46
48
60
63
36
38
43
44
48
50
130
135
110
115
140
145
53
55
67
70
44
46
51
52
56
58
187
191
168
173
187
192
92
95
102
104
66
67
75
76
79
80
LRA
MINIMUM UNIT
DISCONNECT SIZE
15
072 (6 Tons)
060 (5 Tons)
048 (4 Tons)
036 (3 Tons)
UNIT SIZE
575---3---60
460---3---60
208/230---3---60
575---3---60
575
3 60
460---3---60
208/230---3---60
208/230---1---60
575---3---60
460---3---60
208/230---3---60
208/230---1---60
575---3---60
460---3---60
Perfect
Humidity
HS
STD
HS
STD
HS
STD
Perfect
Humidity
HS
STD
HS
STD
HS
STD
STD
Perfect
Humidity
HS
STD
HS
STD
HS
STD
STD
Perfect
Humidity
HS
STD
HS
STD
HS
STD
STD
208/230---1---60
208/230---3 60
IFM TYPE
NOMINAL
V---PH---Hz
581B036---072
518
414
187
518
414
187
187
518
414
187
187
518
414
187
187
Min
632
508
254
632
508
254
254
632
508
254
254
632
508
254
254
Max
VOLTAGE
RANGE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
QTY
77
7.7
96
9.6
20 5
20.5
71
7.1
9
17 3
17.3
28 8
28.8
64
6.4
64
6.4
13 5
13.5
23 7
23.7
42
4.2
51
5.1
10 3
10.3
16
RLA
56
75
156
50
62
123
169
40
46 5
46.5
93
126
31
39
77
88
LRA
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
QTY
0 6†
0.6†
08
0.8
06
0.6
14
1.4
0 8†
0.8†
06
0.6
08
0.8
15
1.5
15
1.5
04
0.4
04
0.4
04
0.4
07
0.7
07
0.7
0 4†
0.4†
04
0.4
04
0.4
07
0.7
07
0.7
FLA
OFM (each)
0 3†
0.3†
0 3†
0.3†
03
0.3
3 4†
3.4†
28
2.8
20
2.0
34
3.4
26
2.6
75
7.5
06
0.6
03
0.3
58
5.8
3 4†
3.4†
28
2.8
20
2.0
34
3.4
26
2.6
75
7.5
58
5.8
66
6.6
2 6†
2.6†
20
2.0
19
1.9
26
2.6
22
2.2
58
5.8
49
4.9
49
4.9
2 6†
2.6†
20
2.0
19
1.9
26
2.6
22
2.2
52
5.2
49
4.9
49
4.9
IFM
FLA
06
0.6
0 3†
0.3†
0 3†
0.3†
03
0.3
06
0.6
06
0.6
0 9†
0.9†
0 3†
0.3†
03
0.3
06
0.6
06
0.6
0 9†
0.9†
0 3†
0.3†
03
0.3
06
0.6
06
0.6
FLA
COMBUSTION
FAN MOTOR
Table 4—Electrical Data 581B
COMPRESSOR (each)
581B,C
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
CONV
OUTLET
25.6
31.6
18.5
24.5
19.4
25.4
9.0
11.7
9.4
12.1
7.6
9.7
7.7
9.8
8.3
10.4
35.2
41.2
22.5
28.5
23.4
29.4
10.6
13.3
11.0
13.7
10.3
12.5
10.4
12.6
11.0
13.2
44.1
50.1
28.9
34.9
30.6
36.6
14.7
17.4
15.5
18.2
11.5
13.6
12.3
14.4
12.2
14.4
32.8
38.8
34.5
40.5
15.2
17.9
16.0
18.7
12.4
14.6
13.2
15.4
12.8
15.0
MCA
30
35
25
30
25
30
15
15
15
15
10
15
10
15
10
15
45
50
30
35
30
35
15
15
15
15
15
15
15
15
15
15
60
60
35
40
35
40
20
20
20
20
15
15
15
20
15
20
40
45
40
45
20
20
20
25
15
20
20
20
15
20
*
MOCP**
POWER SUPPLY
25
30
18
24
19
25
9
11
9
12
7
9
8
10
8
10
34
39
22
27
23
29
10
13
11
13
10
12
10
12
11
13
42
48
28
34
30
36
14
17
15
18
11
13
12
14
12
14
32
37
34
39
15
17
16
18
12
14
13
15
13
15
FLA
101
106
90
95
120
124
46
48
60
63
36
38
43
44
52
54
139
144
106
111
136
140
54
56
68
70
45
47
52
53
61
63
206
210
168
173
187
192
84
87
94
96
63
64
72
73
76
77
200
205
219
224
97
99
107
109
69
70
79
80
81
83
LRA
MINIMUM UNI
DISCONNECT SIZE
Step 8 —Adjust Factory--Installed Options
581B,C
Perfect Humidity™ Adaptive Dehumidification
System
Perfect Humidity system operation can be controlled by field
installation of a Bryant--approved humidistat. (See Fig. 15.)
NOTE: A light commercial Thermidistat™ device (Fig. 16) can
be used instead of the humidistat if desired. The Thermidistat
device includes a thermostat and a humidistat. The humidistat is
normally used in applications where a temperature sensor is
already provided.
% RELATIVE HUMIDITY
Fig. 15 --- Accessory Field--Installed Humidistat
Fig. 16 --- Light Commercial Thermidistat Device
C06358
C06359
To install the humidistat:
1. Route humidistat cable through hole provided in unit
control box.
2. Some models may be equipped with a raceway built into
the corner post located on the left side of control box (See
Fig. 14). This raceway provides the required clearance
between high--voltage and low voltage wiring. For models
without a raceway, ensure to provide the NEC required
clearance between the high--voltage and low--voltage
wiring.
3. Use a wire nut to connect humidistat cable into lowvoltage wiring as shown in Fig. 17.
To install Thermidistat device:
1. Route Thermidistat cable through hole provided in unit
control box.
2. Some models may be equipped with a raceway built into
the corner post located on the left side of control box (See
Fig. 14). This raceway provides the required clearance
between high--voltage and low voltage wiring. For models
without a raceway, ensure to provide the NEC required
clearance between the high--voltage and low--voltage
wiring.
3. A field-supplied relay must be installed between the
Thermidistat and the Humidi-Mizer circuit (recommended
relay: HN61KK324). (See Fig. 18.) The relay coil is
connected between the DEHUM output and C (common)
of the unit. The relay controls thePerfect Humidity
solenoid valve and must be wired between the Perfect
Humidity fuse and the low-pressure switch. Refer to the
installation instructions included with the Bryant Light
Commercial Thermidistat device for more information.
Manual Outdoor Damper
The outdoor--air hood and screen are attached to the basepan at
the bottom of the unit for shipping.
Assembly:
1. Determine quantity of ventilation required for building.
Record amount for use in Step 8.
2. Remove and save outdoor air opening panel and screws.
(See Fig. 19.)
3. Remove evaporator coil access panel. Separate hood and
screen from basepan by removing the 4 screws securing
them. Save all screws.
4. Replace evaporator coil access panel.
5. Place hood on front of outdoor air opening panel. See
Fig. 20 for hood details. Secure top of hood with the
4 screws removed in Step 3. (See Fig. 21.)
6. Remove and save 6 screws (3 on each side) from sides of
the manual outdoor-air damper.
7. Align screw holes on hood with screw holes on side of
manual outdoor-air damper. (See Fig. 28 and 21.) Secure
hood with 6 screws from Step 6.
8. Adjust minimum position setting of the damper blade by
adjusting the manual outdoor-air adjustment screws on the
front of the damper blade. (See Fig. 19.) Slide blade
vertically until it is in the appropriate position determined
by Fig. 22. Tighten screws.
9. Remove and save screws currently on sides of hood.
Insert screen. Secure screen to hood using the screws. (See
Fig. 21.)
Convenience Outlet
An optional convenience outlet provides power for rooftop use.
For maintenance personnel safety, the convenience outlet power
is off when the unit disconnect is off. Adjacent unit outlets may
be used for service tools.
16
LEGEND
—
—
—
—
—
—
—
—
Circuit Breaker
Cooling Relay
Dehumidify Relay
Discharge Solenoid Valve
Heater Relay
Low Pressure Switch
Liquid Solenoid Valve
Low Temperature Lockout
Terminal (Unmarked)
Splice
Factory Wiring
Field Control Wiring
Field Power Wiring
Field Splice
C06128
Fig. 17 --- Typical Perfect Humidityt Adaptive Dehumidification System
Humidistat Wiring (208/230--V Unit Shown)
LCT
ROOF TOP UNIT
R
C
Y1
Y2
G
W1
W2
R
C
Y1
Y2
G
W1
W2
DEHUM
OC
CB
LCT
LLSV
LTLO
—
—
—
—
R1
PINK
TSTAT WIRES
LEGEND
Circuit Breaker
Light Commercial Thermidistat™ Device
Liquid Line Solenoid Valve
Low Temperature Lockout
R1
PINK
CB
3.2 AMPS
LTLO
RED
PINK
24 V
FROM
PERFECT HUMIDITY SYSTEM
LLSV
PERFECT HUMIDITY SYSTEM
Fig. 18 --- Typical Rooftop Unit with Perfect Humidity
Adaptive Dehumidification System with Thermidistat Device
C06360
OUTDOOR
AIR OPENING
PANEL
3 SCREWS
(SIDE)
C06130
Fig. 19 --- Damper Panel with Manual Outdoor--Air
Damper Installed
Fig. 20 --- Outdoor--Air Hood Details
17
C06013
581B,C
CB
CR
DHR
DSV
HR
LPS
LSV
LTLO
C06131
581B,C
Fig. 21 --- Outdoor--Air Damper With
Hood Attached
Fig. 22 --- Outdoor--Air Damper Position Setting
C06132
ECONOMI$ER IV
CONTROLLER
WIRING
HARNESS
ACTUATOR
OUTSIDE AIR
TEMPERATURE SENSOR
LOW AMBIENT
SENSOR
Optional Economi$er IV
See Fig. 23 for EconoMi$er IV component locations.
NOTE: These instructions are for installing the optional
EconoMi$er IV. Refer to the accessory EconoMi$er IV when
field installing an EconoMi$er IV accessory.
1. To remove the existing unit filter access panel, raise the
panel and swing the bottom outward. The panel is now
disengaged from the track and can be removed. (See
Fig. 24.)
2. The box with the economizer hood components is shipped
in the compartment behind the economizer. The
EconoMi$er IV controller is mounted on top of the
EconoMi$er IV. To remove the component box from its
shipping position, remove the screw holding the hood box
bracket to the top of the economizer. Slide the hood box
out of the unit. (See Fig. 25.)
IMPORTANT: If the power exhaust accessory is to be installed
on the unit, the hood shipped with the unit will not be used and
must be discarded. Save the aluminum filter for use in the power
exhaust hood assembly.
3. The indoor coil access panel will be used as the top of the
hood. Remove the screws along the sides and bottom of
the indoor coil access panel. (See Fig. 26.)
4. Swing out indoor coil access panel and insert the hood
sides under the panel (hood top). Use the screws provided
to attach the hood sides to the hood top. Use screws
provided to attach the hood sides to the unit. (See Fig. 27.)
5. Remove the shipping tape holding the economizer
barometric relief damper in place.
6. Insert the hood divider between the hood sides. (See
Fig. 28 and 29.) Secure hood divider with 2 screws on
each hood side. The hood divider is also used as the
bottom filter rack for the aluminum filter.
7. Open the filter clips which are located underneath the
hood top. Insert the aluminum filter into the bottom filter
rack (hood divider). Push the filter into position past the
open filter clips. Close the filter clips to lock the filter into
place. (See Fig. 28.)
8. Caulk the ends of the joint between the unit top panel and
the hood top. (See Fig. 26.)
9. Replace the filter access panel.
10. Install all EconoMi$er IV accessories. EconoMi$er IV
wiring is shown in Fig. 29.
Barometric flow capacity is shown in Fig. 30. Outdoor air
leakage is shown in Fig. 33. Return air pressure drop is shown in
Fig. 32.
FILTER ACCESS PANEL
Fig. 23 --- EconoMi$er IV Component Locations
C06021
COMPRESSOR
ACCESS PANEL
OUTDOOR-AIR OPENING AND
INDOOR COIL ACCESS PANEL
Fig. 24 --- Typical Access Panel Locations
18
C06023
B
Hood
ox
HOOD BOX
BRACKET
Supply Air Temperature (SAT) Sensor
The supply air temperature sensor is a 3k ohm thermistor located
at the inlet of the indoor fan. (See Fig. 34.) This sensor is factory
installed. The operating range of temperature measurement is 0°
to 158_F. See Table 5 for sensor temperature/resistance values.
Table 5—Supply Air Sensor Temperature/
Resistance Values
C06024
Fig. 25 --- Hood Box Removal
SIDE
PANEL
INDOOR
COIL
ACCESS
PANEL
TOP
SIDE
PANEL
CAULK
HERE
INDOOR
COIL
ACCESS
PANEL
Fig. 26 --- Indoor Coil Access Panel Relocation
RESISTANCE (ohms)
200,250
100,680
53,010
29,091
16,590
9,795
5,970
3,747
3,000
2,416
1,597
1,080
746
525
376
321
274
203
153
116
102
89
70
55
17 1/4”
C06025
DIVIDER
TOP
PANEL
OUTSIDE
AIR
INDOOR COIL
ACCESS PANEL
LEFT
HOOD
SIDE
581B,C
TEMPERATURE (F)
–58
–40
–22
–4
14
32
50
68
77
86
104
122
140
158
176
185
194
212
230
248
257
266
284
302
HOOD
CLEANABLE
ALUMINUM
FILTER
FILTER
SCREW
B
19 1/16”
BAROMETRIC
RELIEF
FILTER
CLIP
33 3/8”
Fig. 28 --- Filter Installation
C06027
HOOD DIVIDER
Fig. 27 --- Outdoor--Air Hood Construction
C06026
Economi$er IV Standard Sensors
Outdoor Air Temperature (OAT) Sensor
The outdoor air temperature sensor (HH57AC074) is a 10 to 20
mA device used to measure the outdoor-air temperature. The
outdoor-air temperature is used to determine when the
EconoMi$er IV can be used for free cooling. The sensor is
factory-installed on the EconoMi$er IV in the outdoor airstream.
(See Fig. 23 and 33.) The operating range of temperature
measurement is 40_ to 100_F.
The temperature sensor looks like an eyelet terminal with wires
running to it. The sensor is located in the “crimp end” and is
sealed from moisture.
Outdoor Air Lockout Sensor
The Economi$er IV is equipped with an ambient temperature
lockout switch located in the outdoor air stream which is used to
lockout the compressors below a 42_F ambient temperature. (See
Fig. 23.)
19
581B,C
Economi$er IV Control Modes
Determine the EconoMi$er IV control mode before set up of the
control. Some modes of operation may require different
sensors. (See Table 6.) The EconoMi$er IV is supplied from the
factory with a supply--air temperature sensor and an outdoor-- air
temperature sensor. This allows for operation of the EconoMi$er
IV with outdoor air dry bulb changeover control. Additional
accessories can be added to allow for different types of
changeover control and operation of the EconoMi$er IV and unit.
Outdoor Dry Bulb Changeover
The standard controller is shipped from the factory configured for
outdoor dry bulb changeover control. The outdoor--air and
supply--air temperature sensors are included as standard. For this
control mode, the outdoor temperature is compared to an
adjustable set point selected on the control. If the outdoor-air
temperature is above the set point, the EconoMi$er IV will adjust
the outdoor-air dampers to minimum position. If the outdoor air
temperature is below the set point, the position of the outdoor air
dampers will be controlled to provide free cooling using outdoor
air. When in this mode, the LED next to the free cooling set point
potentiometer will be on. The changeover temperature set point is
controlled by the free cooling set point potentiometer located on
the control. (See Fig. 35.) The scale on the potentiometer is A, B,
C, and D. See Fig. 36 for the corresponding temperature
changeover values.
Table 6—Economi$er IV Sensor Usage
APPLICATION
Outdoor Air
Dry Bulb
Differential
Dry Bulb
Single Enthalpy
Differential
Enthalpy
CO2 for DCV
Control using a
Wall-Mounted
CO2 Sensor
CO2 for DCV
Control using a
Duct-Mounted
CO2 Sensor
ECONOMI$ER IV WITH OUTDOOR AIR
DRY BULB SENSOR
Accessories Required
None. The outdoor air dry bulb sensor
is factory installed.
CRTEMPSN002A00*
HH57AC078
HH57AC078
and
CRENTDIF004A00*
33ZCSENCO2
33ZCSENCO2†
and
33ZCASPCO2**
O
R
CRCBDIOX005A00††
Differential Dry Bulb Control
For differential dry bulb control the standard outdoor dry bulb
sensor is used in conjunction with an additional accessory dry
bulb sensor (part number CRTEMPSN002A00). The accessory
sensor must be mounted in the return airstream. (See Fig. 37.)
Wiring is provided in the EconoMi$er IV wiring harness. (See
Fig. 29.)
In this mode of operation, the outdoor-air temperature is
compared to the return-air temperature and the lower temperature
airstream is used for cooling. When using this mode of
changeover control, turn the enthalpy setpoint potentiometer fully
clockwise to the D setting. (See Fig. 35.)
Outdoor Enthalpy Changeover
For enthalpy control, accessory enthalpy sensor (part number
HH57AC078) is required. Replace the standard outdoor dry bulb
temperature sensor with the accessory enthalpy sensor in the same
mounting location. (See Fig. 23 and 33.) When the outdoor air
enthalpy rises above the outdoor enthalpy changeover set point,
the outdoor-air damper moves to its minimum position. The
outdoor enthalpy changeover set point is set with the outdoor
enthalpy set point potentiometer on the EconoMi$er IV
controller. The set points are A, B, C, and D. (See Fig. 38.) The
factory-installed 620-ohm jumper must be in place across
terminals SR and SR+ on the EconoMi$er IV controller. (See Fig.
23 and 39.)
Differential Enthalphy Control
For differential enthalpy control, the EconoMi$er IV controller
uses
two
enthalpy
sensors
(HH57AC078
and
CRENTDIF004A00), one in the outside air and one in the return
air duct. The EconoMi$er IV controller compares the outdoor air
enthalpy to the return air enthalpy to determine EconoMi$er IV
use. The controller selects the lower enthalpy air (return or
outdoor) for cooling. For example, when the outdoor air has a
lower enthalpy than the return air, the EconoMi$er IV opens to
bring in outdoor air for free cooling.
Replace the standard outside air dry bulb temperature sensor with
the accessory enthalpy sensor in the same mounting location.
(See Fig. 23.) Mount the return air enthalpy sensor in the return
air duct. (See Fig. 37.) Wiring is provided in the EconoMi$er IV
wiring harness. (See Fig. 29.) The outdoor enthalpy changeover
set point is set with the outdoor enthalpy set point potentiometer
on the EconoMi$er IV controller. When using this mode of
changeover control, turn the enthalpy setpoint potentiometer fully
clockwise to the D setting.
*CRENTDIF004A00 and CRTEMPSN002A00 accessories are used on many
different base units. As such, these kits may contain parts that will not be
needed for installation.
† 33ZCSENCO2 is an accessory CO2 sensor.
** 33ZCASPCO2 is an accessory aspirator box required for duct-mounted
applications.
†† CRCBDIOX005A00 is an accessory that contains both 33ZCSENCO2
and 33ZCASPCO2 accessories.
20
FOR OCCUPANCY CONTROL
REPLACE JUMPER WITH
FIELD-SUPPLIED TIME CLOCK
8
581B,C
7
LEGEND
DCV— Demand Controlled Ventilation
IAQ — Indoor Air Quality
LA — Low Ambient Lockout Device
OAT — Outdoor-Air Temperature
POT — Potentiometer
RAT — Return-Air Temperature
Potentiometer Defaults Settings:
Power Exhaust Middle
Minimum Pos.
Fully Closed
DCV Max.
Middle
DCV Set
Middle
Enthalpy
C Setting
NOTES:
1. 620 ohm, 1 watt 5% resistor should be removed only when using differential
enthalpy or dry bulb.
2. If a separate field-supplied 24 v transformer is used for the IAQ sensor power
supply, it cannot have the secondary of the transformer grounded.
3. For field-installed remote minimum position POT, remove black wire jumper
between P and P1 and set control minimum position POT to the minimum
position.
C06028
2500
2000
1500
1000
500
0
0.15
0.05
0.25
STATIC PRESSURE (in. wg)
Fig. 30 --- Barometric Flow Capacity
FLOW IN CUBIC FEET PER MINUTE (cfm)
FLOW IN CUBIC FEET PER MINUTE (cfm)
FLOW IN CUBIC FEET PER MINUTE (cfm)
Fig. 29 --- EconoMi$er IV Wiring
6000
5000
4000
3000
2000
1000
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
STATIC PRESSURE (in. wg)
C06030
C06032
Fig. 32 --- Return--Air Pressure Drop
30
HH57AC078 ENTHALPY
SENSOR
25
C7400
20
A1004
+
15
10
5
0
MOUNTING PLATE
0.13
0.20 0.22
0.25
0.30 0.35 0.40
0.45
0.50
STATIC PRESSURE (in. wg)
Fig. 31 --- Outdoor--Air Damper Leakage
C06031
Fig. 33 --- Enthalpy Sensor and Mounting Plate
21
C06361
SUPPLY AIR
TEMPERATURE
SENSOR
MOUNTING
LOCATION
SUPPLY AIR
TEMPERATURE
SENSOR
C06033
581B,C
Fig. 34 --- Supply Air Sensor Location
Minimum Position Control
There is a minimum damper position potentiometer on the
EconoMi$er IV controller. (See Fig. 35.) The minimum damper
position maintains the minimum airflow into the building during
the occupied period.
When using demand ventilation, the minimum damper position
represents the minimum ventilation position for VOC (volatile
organic compound) ventilation requirements. The maximum
demand ventilation position is used for fully occupied ventilation.
When demand ventilation control is not being used, the minimum
position potentiometer should be used to set the occupied
ventilation position. The maximum demand ventilation position
should be turned fully clockwise.
Adjust the minimum position potentiometer to allow the
minimum amount of outdoor air, as required by local codes, to
enter the building. Make minimum position adjustments with at
least 10_F temperature difference between the outdoor and
return-air temperatures.
To determine the minimum position setting, perform the
following procedure:
1. Calculate the appropriate mixed air temperature using the
following formula:
(TO x
C06034
Fig. 35 --- EconoMi$er IV Controller Potentiometer
and LED Locations
Indoor Air Quality (IAQ) Sensor Input
The IAQ input can be used for demand control ventilation control
based on the level of CO2 measured in the space or return air
duct.
Mount the accessory IAQ sensor according to manufacturer
specifications. The IAQ sensor is wired to the AQ and AQ1
terminals of the controller. Adjust the DCV potentiometers to
correspond to the DCV voltage output of the indoor air quality
sensor at the user-determined set point. (See Fig. 40.)
If a separate field-supplied transformer is used to power the IAQ
sensor, the sensor must not be grounded or the EconoMi$er IV
control board will be damaged.
Exhaust Set Point Adjustment
The exhaust set point will determine when the exhaust fan runs
based on damper position (if accessory power exhaust is
installed). The set point is modified with the Exhaust Fan Set
Point (EXH SET) potentiometer. (See Fig. 35.) The set point
represents the damper position above which the exhaust fans will
be turned on. When there is a call for exhaust, the EconoMi$er IV
controller provides a 45 ± 15 second delay before exhaust fan
activation to allow the dampers to open. This delay allows the
damper to reach the appropriate position to avoid unnecessary fan
overload.
OA + (TR
)
100
x
RA
) =T
TM
100
TO = Outdoor-Air Temperature
OA = Percent of Outdoor Air
TR = Return-Air Temperature
RA = Percent of Return Air
TM = Mixed-Air Temperature
As an example, if local codes require 10% outdoor air during
occupied conditions, outdoor-air temperature is 60_F, and
return-air temperature is 75_F.
(60 x .10) + (75 x .90) = 73.5_F
2. Disconnect the supply air sensor from terminals T and T1.
3. Ensure that the factory-installed jumper is in place across
terminals P and P1. If remote damper positioning is being
used, make sure that the terminals are wired according to
Fig. 29 and that the minimum position potentiometer is
turned fully clockwise.
4. Connect 24 vac across terminals TR and TR1.
5. Carefully adjust the minimum position potentiometer
until the measured supply air temperature matches the
calculated value.
6. Reconnect the mixed air sensor to terminals T and T1.
Remote control of the EconoMi$er IV damper is desirable when
requiring
additional
temporary
ventilation.
If
a
field-supplied remote potentiometer (Honeywell part number
S963B1128) is wired to the EconoMi$er IV controller, the
minimum position of the damper can be controlled from a remote
location.
22
19
LED ON
18
D
17
LED OFF
16
mA
15
14
LED ON
C
LED OFF
13
12
LED ON
B
LED ON
LED OFF
A
11
10
LED OFF
9
40
45
50
55
60
65 70 75 80
DEGREES FAHRENHEIT
85
90
95
100
Fig. 36 --- Outside Air Temperature
Changeover Set Points
C06035
ECONOMI$ER IV
CONTROLLER
ECONOMI$ER IV
Occupancy Control
The factory default configuration for the EconoMi$er IV control
is occupied mode. Occupied mode is provided by the black
jumper from terminal TR to terminal N. When unoccupied mode
is desired, install a field-supplied timeclock function in place of
the jumper between TR and N. (See Fig. 29.) When the timeclock
contacts are closed, the EconoMi$er IV control will be in
occupied mode. When the timeclock contacts are open (removing
the 24-v signal from terminal N), the EconoMi$er IV will be in
unoccupied mode.
Typically the maximum ventilation rate will be about 5 to 10%
more than the typical cfm required per person, using normal
outside air design criteria.
Demand Controlled Ventilation (DCV)
When using the EconoMi$er IV for demand controlled
ventilation, there are some equipment selection criteria which
should be considered. When selecting the heat capacity and cool
capacity of the equipment, the maximum ventilation rate must be
evaluated for design conditions. The maximum damper position
must be calculated to provide the desired fresh air.
A proportional anticipatory strategy should be taken with the
following conditions: a zone with a large area, varied occupancy,
and equipment that cannot exceed the required ventilation rate at
design conditions. Exceeding the required ventilation rate means
the equipment can condition air at a maximum ventilation rate
that is greater than the required ventilation rate for maximum
occupancy. A proportional-anticipatory strategy will cause the
fresh air supplied to increase as the room CO2 level increases
even though the CO2 set point has not been reached. By the time
the CO2 level reaches the set point, the damper will be at
maximum ventilation and should maintain the set point.
In order to have the CO2 sensor control the economizer damper in
this manner, first determine the damper voltage output for
minimum or base ventilation. Base ventilation is the ventilation
required to remove contaminants during unoccupied periods. The
following equation may be used to determine the percent of
outside-air entering the building for a given damper position. For
best results there should be at least a 10 degree difference in
outside and return-air temperatures.
(TO x
GROMMET
RETURN AIR TEMPERATURE
SENSOR
RETURN DUCT
(FIELD-PROVIDED)
Fig. 37 --- Return Air Temperature or Enthalpy
Sensor Mounting Location
C06036
OA + (TR
)
100
x
RA
) =T
TM
100
TO = Outdoor-Air Temperature
OA = Percent of Outdoor Air
TR = Return-Air Temperature
RA = Percent of Return Air
TM = Mixed-Air Temperature
Once base ventilation has been determined, set the minimum
damper position potentiometer to the correct position.
23
581B,C
To control the minimum damper position remotely, remove the
factory-installed jumper on the P and P1 terminals on the
EconoMi$er IV controller. Wire the field-supplied potentiometer
to the P and P1 terminals on the EconoMi$er IV controller. (See
Fig. 39.)
Damper Movement
Damper movement from full open to full closed (or vice versa)
takes 21/2 minutes.
Thermostats
The EconoMi$er IV control works with conventional thermostats
that have a Y1 (cool stage 1), Y2 (cool stage 2), W1 (heat stage
1), W2 (heat stage 2), and G (fan). The EconoMi$er IV control
does not support space temperature sensors. Connections are
made at the thermostat terminal connection board located in the
main control box.
110
(43)
46
85
90
95 100 105
(29) (32) (35) (38) (41)
44
CONTROL CONTROL POINT
CURVE
APPROX. deg. F (deg. C)
(%
)
EH
UM
IDI
TY
38
LA
32
TIV
34
75
(24)
RE
80
22
60
70
24
65
(18)
10
0
90
28
30
70
(21)
26
EN
T
HA
LP
Y
BT
U
PE
R
PO
UN
36 D D
RY
AI
R
40
73 (23)
70 (21)
67 (19)
63 (17)
20
50
60
(16)
40
A
16
14
50
(10)
12
45
(7)
30
55
(13) B
18
581B,C
80
(27)
42
AT 50% RH
A
B
C
D
C
20
D
40
(4)
10
35
(2)
B A
D C
35
(2)
40
(4)
45
(7)
50
(10)
55
60
(13) (16)
65
70
(18) (21)
75
(24)
80
85
(27) (29)
HIGH LIMIT
CURVE
90
95
(32) (35)
105 110
(41) (43)
100
(38)
APPROXIMATE DRY BULB TEMPERATURE--degrees F (degrees C)
C06037
Fig. 38 --- Enthalpy Changeover Set Points
The same equation can be used to determine the occupied or
maximum ventilation rate to the building. For example, an output
of 3.6 volts to the actuator provides a base ventilation rate of 5%
and an output of 6.7 volts provides the maximum ventilation rate
of 20% (or base plus 15 cfm per person). Use Fig. 37 to
determine the maximum setting of the CO2 sensor. For example,
a 1100 ppm set point relates to a 15 cfm per person design. Use
the 1100 ppm curve on Fig. 40 to find the point when the CO2
sensor output will be 6.7 volts. Line up the point on the graph
with the left side of the chart to determine that the range
configuration for the CO2 sensor should be 1800 ppm. The
EconoMi$er IV controller will output the 6.7 volts from the CO2
sensor to the actuator when the CO2 concentration in the space is
at 1100 ppm. The DCV set point may be left at 2 volts since the
CO2 sensor voltage will be ignored by the EconoMi$er IV
controller until it rises above the 3.6 volt setting of the minimum
position potentiometer.
Once the fully occupied damper position has been determined, set
the maximum damper demand control ventilation potentiometer
to this position. Do not set to the maximum position as this can
result in over-ventilation to the space and potential high-humidity
levels.
EXH
N1
N
2V
EXH
P1
P
Min
Pos
T1
DCV
2V
SO+
SR+
SR
24
Vac
HOT
24 Vac
COM
+
_
Max
10V
1
2
5
DCV
AQ
SO
TR1
Open
T
AQ1
TR
Set
10V
2V
DCV
Set
10V
Free
Cool
B
C
A
D
3
4
EF
EF1
Fig. 39 --- EconoMi$er IV Control
24
C06038
CO2 SENSOR MAX RANGE SETTING
RANGE CONFIGURATION (ppm)
6000
5000
4000
800 ppm
900 ppm
1000 ppm
1100 ppm
3000
2000
1000
2
3
4
5
6
7
8
DAMPER VOLTAGE FOR MAX VENTILATION RATE
Fig. 40 --- CO2 Sensor Maximum Range Setting
CO2 Sensor Configuration
The CO2 sensor has preset standard voltage settings that can be
selected anytime after the sensor is powered up. (See Table 7.)
Use setting 1 or 2 for Bryant equipment. (See Table 7.)
1. Press Clear and Mode buttons. Hold at least 5 seconds
until the sensor enters the Edit mode.
2. Press Mode twice. The STDSET Menu will appear.
3. Use the Up/Down button to select the preset number. (See
Table 7.)
4. Press Enter to lock in the selection.
5. Press Mode to exit and resume normal operation.
The custom settings of the CO2 sensor can be changed anytime
after the sensor is energized. Follow the steps below to change the
non-standard settings:
1. Press Clear and Mode buttons. Hold at least 5 seconds
until the sensor enters the Edit mode.
2. Press Mode twice. The STDSET Menu will appear.
3. Use the Up/Down button to toggle to the NONSTD menu
and press Enter.
4. Use the Up/Down button to toggle through each of the
nine variables, starting with Altitude, until the desired
setting is reached.
5. Press Mode to move through the variables.
6. Press Enter to lock in the selection, then press Mode to
continue to the next variable.
Dehumidification of Fresh Air with DCV Control
Information from ASHRAE indicates that the largest humidity
load on any zone is the fresh air introduced. For some
applications, a device such as an energy recovery unit can be
added to reduce the moisture content of the fresh air being
brought into the building when the enthalpy is high. In most
cases, the normal heating and cooling processes are more than
adequate to remove the humidity loads for most commercial
applications.
If normal rooftop heating and cooling operation is not adequate
for the outdoor humidity level, an energy recovery unit and/or a
dehumidification option should be considered.
C06039
Step 9 —Adjust Evaporator--Fan Speed
Adjust evaporator-fan speed to meet jobsite conditions.
Tables 8 and 9 show fan rpm at motor pulley settings. Tables 10
and 14 show maximum amp draw of belt-drive motor. Table 13
shows sound data. Refer to Tables 15--34 for performance data.
See Table 11 for accessory static pressure drop. See Fig. 41 for
the Perfect Humidity™ system static pressure drops.
Belt Drive Motors
Fan motor pulleys are factory set for speed shown in Table 1 or 2.
Check pulley alignment and belt tension prior to start-up.
To change fan speed:
1. Shut off the unit power supply and tag disconnect.
2. Loosen the belt by loosening the fan motor mounting nuts.
(See Fig. 42.)
3. Loosen movable pulley flange setscrew. (See Fig. 43.)
4. Screw movable flange toward fixed flange to increase
speed and away from fixed flange to decrease speed.
Increasing fan speed increases load on motor. Do not
exceed maximum speed specified in Table 1 or 2.
5. Set movable flange at nearest keyway of pulley hub and
tighten setscrew. (See Table 1 or 2 for speed change for
each full turn of pulley flange.)
6. Adjust belt tension and align fan and motor pulleys per
guidance below.
NOTE: Once the required flange position is determined for the
correct blower rpm, it is recommended (bu not required) that the
variable pitch pulley be replaced with a corresponding size fixed
sheave pulley.
To align fan and motor pulleys, loosen fan pulley setscrews and
slide fan pulley along fan shaft. Make angular alignment by
loosening motor from mounting.
Additional motor and fan alignment, as well as angular alignment
can be made by loosening the four motor mounting bolts from
the mounting plate.
To adjust belt tension:
1. Loosen the two motor mounting nuts as shown in Fig. 42.
Some models may have a third mounting nut located on
the opposite side of the fan motor mounting plate.
2. Slide motor mounting plate away from fan scroll for
proper belt tension (1/2-in. deflection with 8 to 10 lb of
force) and tighten mounting nuts.
3. Adjust lock bolt and nut on mounting plate to secure
motor in fixed position.
25
581B,C
0
Table 7—CO2 Sensor Standard Settings
OUTPUT
VENTILATION
RATE
(cfm/Person)
ANALOG
OUTPUT
CO2
CONTROL RANGE
(ppm)
OPTIONAL
RELAY SETPOINT
(ppm)
RELAY
HYSTERESIS
(ppm)
Proportional
Any
0-10V
4-20 mA
0-2000
1000
50
Proportional
Any
2-10V
7-20 mA
0-2000
1000
50
3
Exponential
Any
0-10V
4-20 mA
0-2000
1100
50
4
Proportional
15
0-10V
4-20 mA
0-1100
1100
50
Proportional
20
0-10V
4-20 mA
0- 900
900
50
Exponential
15
0-10V
4-20 mA
0-1100
1100
50
Exponential
20
0-10V
4-20 mA
0- 900
900
50
Proportional
—
0-10V
4-20 mA
0-9999
5000
500
—
0-10V
4-20 mA
0-2000
700
50
SETTING
EQUIPMENT
1
Interface w/Standard
Building Control System
2
5
Economizer
6
581B,C
7
8
Health & Safety
9
Parking/Air Intakes/
Loading Docks
Proportional
LEGEND
ppm — Parts Per Million
0.35
0.3
DELTA P IN. WG
0.25
0.2
0.15
0.1
4 & 5 ton
6 ton
0.05
3 ton
0
0
1000
2000
4000
3000
5000
6000
Fig. 41 --- Perfect Humidityt Adaptive Dehumidification System Static Pressure Drop (in. wg)
Fig. 42 --- Belt Drive Motor Mounting
C06134
Fig. 43 --- Indoor--Fan Pulley Adjustment
26
C06133
C06041
Table 8—581B and 581C Fan Rpm at Motor Pulley Setting With Standard Motor*
UNIT
1/
2
0
936
1044
1185
1460
1585
024
036
048
060
072
906
1008
1144
1425
1538
MOTOR PULLEY TURNS OPEN
2
21/2
3
31/2
4
816
786
756
726
696
898
862
826
789
753
1019
978
936
895
853
1318
1283
1248
1212
1177
1399
1352
1305
1259
1212
11/2
846
935
1061
1354
1445
1
876
971
1102
1389
1492
41/2
666
716
812
1141
1166
5
639
680
770
1106
1119
51/2
—
—
—
1070
—
6
—
—
—
1035
—
*Approximate fan rpm shown (standard motor/drive).
Table 9—581B Fan Rpm at Motor Pulley Setting With High-Static Motor*
1/
2
0
1455
1455
1685
1685
036
048
060
072
1423
1423
1589
1589
11/2
1360
1360
1525
1525
1
1392
1392
1557
1557
2
1328
1328
1493
1493
MOTOR PULLEY TURNS OPEN
21/2
3
31/2
1297
1265
1233
1297
1265
1233
1460
1428
1396
1460
1428
1396
4
1202
1202
1364
1364
41/2
1170
1170
1332
1332
5
1138
1138
1300
1300
51/2
1107
1107
—
—
6
1075
1075
—
—
581B,C
UNIT
*Approximate fan rpm shown (high-static motor/drive).
Table 10—Evaporator-Fan Motor Data — Standard Motor
UNIT
581B
581C
024
036
048
060
072
UNIT
PHASE
MAXIMUM
CONTINUOUS BHP*
MAXIMUM
OPERATING WATTS*
Single
Single
0.58
1.20
580
1000
Three
1.20
1000
Single
1.20
1000
Three
1.20
1000
Single
1.30
1455
Three
2.40
2120
Three
2.40
2120
UNIT VOLTAGE
MAXIMUM
AMP DRAW
208/230
208/230
208/230
460
575
208/230
208/230
460
575
208/230
208/230
460
575
208/230
460
575
2.0
4.9
4.9
2.2
2.2
4.9
4.9
2.2
2.2
7.0
6.7
3.0
3.0
6.7
3.0
3.0
LEGEND
Bhp — Brake Horsepower
*Extensive motor and electrical testing on these units ensures that the full horsepower and watts range of the motors can be utilized with confidence. Using the
fan motors up to the ratings shown in this table will not result in nuisance tripping or premature motor failure. Unit warranty will not be affected.
Table 11—Accessory Static Pressure
COMPONENT
Vertical EconoMi$er IV
Horizontal EconoMi$er IV
600
800
1000
1250
CFM
1500
1750
2000
2250
2500
2750
3000
0.010
0.020
0.035
0.045
0.065
0.080
0.120
0.145
0.175
0.220
0.255
—
—
—
—
—
0.100
0.125
0.150
0.180
0.225
0.275
Table 12—Evaporator-Fan Motor Data — High-Static Motors
UNIT
581B
UNIT
PHASE
MAXIMUM
CONTINUOUS BHP*
MAXIMUM
OPERATING WATTS*
036
Three
2.40
2120
048
Three
2.40
2120
060
Three
2.90
2615
072
Three
2.90
2615
UNIT VOLTAGE
MAXIMUM
AMP DRAW
208/230
460
575
208/230
460
575
208/230
460
575
208/230
460
575
6.7
3.0
3.0
6.7
3.0
3.0
8.6
3.9
3.9
8.6
3.9
3.9
LEGEND
Bhp — Brake Horsepower
*Extensive motor and electrical testing on these units ensures that the full horsepower and watts range of the motors can be utilized with confidence. Using the
fan motors up to the ratings shown in this table will not result in nuisance tripping or premature motor failure. Unit warranty will not be affected.
27
Table 13—581B Outdoor Sound Power (Total Unit)
UNIT
036, 048
060, 072
ARI
RATING
(decibels)
76
80
OCTAVE BANDS
63
125
250
500
1000
2000
4000
8000
55.9
59.1
66.0
68.9
64.0
68.7
66.2
71.9
68.4
74.0
64.5
68.9
61.7
65.7
57.3
59.0
LEGEND
ARI --- Air Conditioning and Refrigeration Institute
Table 14—581C Outdoor Sound Power (Total Unit)
581B,C
UNIT
ARI
RATING
(decibels)
OCTAVEBANDS
A --WEIGHTED
(db)
63
125
250
500
1000
2000
4000
8000
024---048
76
76
55.9
66.0
64.0
66.2
68.4
64.5
61.7
57.3
060
80
80
59.1
68.9
68.7
71.9
74.0
68.9
65.7
59.0
GENERAL FAN PERFORMANCE NOTES
1. Values include losses for filters, unit casing, and wet coils. See Table 11 and Fig. 38 for accessory/FIOP static pressure information.
2. Extensive motor and electrical testing on these units ensures that the full range of the motor can be utilized with confidence. Using the
fan motors up to the ratings shown will not result in nuisance tripping or premature motor failure. Unit warranty will not be affected.
See Tables 8 and 9 for additional information.
3. Use of a field-supplied motor may affect wire sizing. Contact your Bryant representative to verify.
4. Interpolation is permissible. Do not extrapolate.
Table 15—Fan Performance 581C 024 — Vertical Discharge Units; Standard Motor (Belt Drive)**
AIRFLOW
(Cfm)
600
700
800
900
1000
0.1
Rpm
Bhp
EXTERNAL STATIC PRESSURE (in. wg)
0.2
0.4
0.6
0.8
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
500
529
547
570
599
531
567
592
620
650
0.08
0.09
0.10
0.13
0.15
0.08
0.09
0.12
0.14
0.16
607
633
660
691
717
0.14
0.16
0.19
0.22
0.26
713
739
761
793
818
28
0.21
0.24
0.27
0.32
0.36
788
816
845
870
894
0.29
0.32
0.37
0.42
0.47
1.0
Rpm
878
902
937
957
981
Bhp
0.37
0.41
0.47
0.53
0.58
Table 16—Fan Performance 581B 036, 581C 036 — Vertical Discharge Units; Standard Motor
(Belt Drive)*
CFM
900
1000
1100
1200
1300
1400
1500
Rpm
567
599
632
666
701
737
773
AIRFLOW
CFM
900
1000
1100
1200
1300
1400
1500
Rpm
1016
1041
1066
1093
1119
1147
1175
0.2
Bhp
0.15
0.18
0.22
0.26
0.31
0.36
0.42
1.2
Bhp
0.51
0.59
0.68
0.77
0.87
0.98
1.09
Watts
145
177
215
257
306
361
422
Watts
505
587
674
767
866
972
1086
Rpm
688
717
747
778
810
842
875
Rpm
1080
1104
1129
1155
1181
1208
—
0.4
Bhp
0.22
0.27
0.31
0.37
0.43
0.49
0.57
1.4
Bhp
0.57
0.67
0.76
0.87
0.98
1.09
—
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
222
786
0.30
296
871
265
814
0.35
349
897
313
842
0.41
407
925
367
871
0.47
471
952
426
901
0.54
540
981
491
931
0.62
616
1010
564
963
0.70
699
1040
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
572
1139
0.64
637
1195
662
1163
0.74
737
1219
759
1188
0.85
843
1243
861
1213
0.96
955
1268
970
1239
1.08
1073
1294
1086
—
—
—
—
—
—
—
—
—
0.8
Bhp
0.37
0.43
0.50
0.57
0.65
0.74
0.84
1.8
Bhp
0.71
0.81
0.93
1.05
1.18
—
—
Watts
368
430
498
572
651
738
831
Watts
702
811
925
1047
1175
—
—
Rpm
947
972
999
1025
1053
1081
1110
Rpm
1249
1272
1296
1321
—
—
—
1.0
Bhp
0.44
0.51
0.59
0.67
0.76
0.86
0.96
2.0
Bhp
0.77
0.89
1.01
1.14
—
—
—
Watts
437
509
587
670
760
856
960
Watts
765
883
1007
1137
—
—
—
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 680 to 1044 rpm. All other rpms require field-supplied
drive.
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 1.20.
3. See general fan performance notes.
Table 17—Fan Performance 581B 036, 581C 036 — Vertical Discharge Units; High-Static Motor
(Belt Drive)*
AIRFLOW
CFM
900
1000
1100
1200
1300
1400
1500
Rpm
0.2
Bhp
Watts
Rpm
0.4
Bhp
567
599
632
666
701
737
773
0.15
0.18
0.22
0.26
0.31
0.36
0.42
145
177
215
257
306
361
422
688
717
747
778
810
842
875
0.22
0.27
0.31
0.37
0.43
0.49
0.57
Rpm
1.2
Bhp
Watts
Rpm
1.4
Bhp
1016
1041
1066
1093
1119
1147
1175
0.51
0.59
0.68
0.77
0.87
0.98
1.09
505
587
674
767
866
972
1086
1080
1104
1129
1155
1181
1208
1235
0.57
0.67
0.76
0.87
0.98
1.09
1.22
AIRFLOW
CFM
900
1000
1100
1200
1300
1400
1500
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 2.40.
3. See general fan performance notes.
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts
Rpm
Bhp
Watts
Rpm
0.8
Bhp
Watts
Rpm
1.0
Bhp
Watts
871
897
925
952
981
1010
1040
0.37
0.43
0.50
0.57
0.65
0.74
0.84
368
430
498
572
651
738
831
947
972
999
1025
1053
1081
1110
0.44
0.51
0.59
0.67
0.76
0.86
0.96
437
509
587
670
760
856
960
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts
Rpm
Bhp
Watts
Rpm
1.8
Bhp
Watts
Rpm
2.0
Bhp
Watts
222
265
313
367
426
491
564
572
662
759
861
970
1086
1209
786
814
842
871
901
931
963
1139
1163
1188
1213
1239
1265
1292
0.30
0.35
0.41
0.47
0.54
0.62
0.70
0.64
0.74
0.85
0.96
1.08
1.21
1.34
296
349
407
471
540
616
699
637
1195
0.71
702
1249
0.77
765
737
1219
0.81
811
1272
0.89
883
843
1243
0.93
925
1296
1.01
1007
955
1268
1.05
1047
1321
1.14
1137
1073
1294
1.18
1175
1346
1.28
1275
1199
1320
1.32
1310
1371
1.43
1419
1332
1346
1.46
1452
1397
1.58
1572
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 1075 to 1455 rpm. All other rpms require field-supplied
drive.
29
581B,C
AIRFLOW
Table 18—Fan Performance 581B 048, 581C 048 — Vertical Discharge Units; Standard Motor
(Belt Drive)*
AIRFLOW
CFM
1200
1300
1400
1500
1600
1700
1800
1900
2000
Rpm
0.2
Bhp
Watts
Rpm
0.4
Bhp
666
701
737
773
810
847
885
923
962
0.26
0.31
0.36
0.42
0.49
0.57
0.66
0.75
0.85
257
306
361
422
491
567
652
745
847
778
810
842
875
909
943
978
1014
1049
0.37
0.43
0.49
0.57
0.65
0.73
0.83
0.94
1.05
AIRFLOW
581B,C
CFM
1200
1300
1400
1500
1600
1700
1800
1900
2000
Rpm
1093
1119
1147
1175
—
—
—
—
—
1.2
Bhp
0.77
0.87
0.98
1.09
—
—
—
—
—
Watts
767
866
972
1086
—
—
—
—
—
Rpm
1155
1181
1208
—
—
—
—
—
—
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 2.40.
3. See general fan performance notes.
1.4
Bhp
0.87
0.98
1.09
—
—
—
—
—
—
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts
Rpm
Bhp
Watts
Rpm
367
426
491
564
643
730
826
930
1043
871
901
931
963
994
1027
1060
1093
—
0.47
0.54
0.62
0.70
0.79
0.89
1.00
1.11
—
471
540
616
699
790
888
994
1109
—
952
981
1010
1040
1070
1101
1133
—
—
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts
Rpm
Bhp
Watts
Rpm
861
1213
0.96
955
1268
970
1239
1.08
1073
1294
1086
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.8
Bhp
Watts
Rpm
1.0
Bhp
Watts
0.57
0.65
0.74
0.84
0.94
1.05
1.16
—
—
572
651
738
831
932
1040
1157
—
—
1025
1053
1081
1110
1140
1170
—
—
—
0.67
0.76
0.86
0.96
1.08
1.20
—
—
—
670
760
856
960
1070
1189
—
—
—
1.8
Bhp
1.05
1.18
—
—
—
—
—
—
—
Watts
1047
1175
—
—
—
—
—
—
—
Rpm
1321
—
—
—
—
—
—
—
—
2.0
Bhp
1.14
—
—
—
—
—
—
—
—
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 770 to 1185 rpm. All other rpms require field-supplied drive.
30
Watts
1137
—
—
—
—
—
—
—
—
Table 19—Fan Performance 581B 048, 581C 048 — Vertical Discharge Units; High-Static Motor (Belt Drive)*
CFM
1200
1300
1400
1500
1600
1700
1800
1900
2000
Rpm
666
701
737
773
810
847
885
923
962
AIRFLOW
CFM
1200
1300
1400
1500
1600
1700
1800
1900
2000
Rpm
1093
1119
1147
1175
1204
1233
1262
1293
1323
0.2
Bhp
0.26
0.31
0.36
0.42
0.49
0.57
0.66
0.75
0.85
1.2
Bhp
0.77
0.87
0.98
1.09
1.21
1.34
1.48
1.63
1.79
Watts
257
306
361
422
491
567
652
745
847
Watts
767
866
972
1086
1207
1336
1473
1620
1776
Rpm
778
810
842
875
909
943
978
1014
1049
Rpm
1155
1181
1208
1235
1263
1292
1321
1350
1380
0.4
Bhp
0.37
0.43
0.49
0.57
0.65
0.73
0.83
0.94
1.05
1.4
Bhp
0.87
0.98
1.09
1.22
1.35
1.49
1.64
1.79
1.96
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 2.40.
3. See general fan performance notes.
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
367
871
0.47
471
952
426
901
0.54
540
981
491
931
0.62
616
1010
564
963
0.70
699
1040
643
994
0.79
790
1070
730
1027
0.89
888
1101
826
1060
1.00
994
1133
930
1093
1.11
1109
1165
1043
1127
1.24
1233
1198
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
861
1213
0.96
955
1268
970
1239
1.08
1073
1294
1086
1265
1.21
1199
1320
1209
1292
1.34
1332
1346
1340
1320
1.48
1472
1373
1480
1348
1.63
1622
1401
1627
1376
1.79
1779
1428
1784
1405
1.96
1946
1457
1950
1434
2.13
2123
1486
0.8
Bhp
0.57
0.65
0.74
0.84
0.94
1.05
1.16
1.29
1.42
1.8
Bhp
1.05
1.18
1.32
1.46
1.61
1.77
1.94
2.12
2.31
Watts
572
651
738
831
932
1040
1157
1283
1417
Watts
1047
1175
1310
1452
1603
1762
1930
2106
2293
Rpm
1025
1053
1081
1110
1140
1170
1200
1231
1263
Rpm
1321
1346
1371
1397
1424
1451
1479
1506
—
1.0
Bhp
0.67
0.76
0.86
0.96
1.08
1.20
1.32
1.46
1.61
2.0
Bhp
1.14
1.28
1.43
1.58
1.74
1.91
2.09
2.28
—
Watts
670
760
856
960
1070
1189
1316
1453
1598
Watts
1137
1275
1419
1572
1732
1901
2078
2265
—
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 1075 to 1455 rpm. All other rpms require field-supplied
drive.
Table 20—Fan Performance 581B 060, 581C 060 Single-Phase — Vertical Discharge Units;
Standard Motor (Belt Drive)*
AIRFLOW
CFM
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
Rpm
848
887
927
967
1007
1048
1090
1131
1173
—
—
0.2
Bhp
0.42
0.49
0.57
0.65
0.75
0.85
0.97
1.09
1.23
—
—
Rpm
1312
1342
1374
—
—
—
—
—
—
—
—
1.2
Bhp
1.07
1.18
1.30
—
—
—
—
—
—
—
—
AIRFLOW
CFM
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
Watts
371
433
502
579
663
757
859
970
1091
—
—
Watts
948
1047
1153
—
—
—
—
—
—
—
—
Rpm
968
1004
1040
1077
1115
1153
1191
1230
—
—
—
0.4
Bhp
0.55
0.63
0.71
0.81
0.91
1.03
1.15
1.29
—
—
—
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
486
1069
0.68
600
1158
556
1103
0.76
678
1190
633
1137
0.86
763
1223
718
1172
0.96
856
1257
811
1208
1.08
957
1291
913
1244
1.20
1066
—
1023
—
—
—
—
1143
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.8
Bhp
0.80
0.90
1.00
1.12
1.24
—
—
—
—
—
—
Watts
715
800
892
993
1101
—
—
—
—
—
—
Rpm
1238
1269
1302
1334
—
—
—
—
—
—
—
1.0
Bhp
0.94
1.04
1.15
1.27
—
—
—
—
—
—
—
Watts
831
922
1022
1130
—
—
—
—
—
—
—
Rpm
1380
—
—
—
—
—
—
—
—
—
—
1.4
Bhp
1.20
—
—
—
—
—
—
—
—
—
—
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
1067
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.8
Bhp
—
—
—
—
—
—
—
—
—
—
—
Watts
—
—
—
—
—
—
—
—
—
—
—
Rpm
—
—
—
—
—
—
—
—
—
—
—
2.0
Bhp
—
—
—
—
—
—
—
—
—
—
—
Watts
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 1.30.
3. See general fan performance notes.
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 1035 to 1460 rpm. All other rpms require field-supplied
drive.
31
581B,C
AIRFLOW
Table 21—Fan Performance 581B 060, 581C 060 Three-Phase — Vertical Discharge Units;
Standard Motor (Belt Drive)*
AIRFLOW
581B,C
CFM
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
Rpm
848
887
927
967
1007
1048
1090
1131
1173
1215
1258
AIRFLOW
CFM
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
Rpm
1312
1342
1374
1406
1438
1471
1504
1538
1572
—
—
0.2
Bhp
0.42
0.49
0.57
0.65
0.75
0.85
0.97
1.09
1.23
1.38
1.54
1.2
Bhp
1.07
1.18
1.30
1.43
1.57
1.72
1.87
2.04
2.23
—
—
Watts
371
433
502
579
663
757
859
970
1091
1223
1365
Watts
948
1047
1153
1268
1391
1523
1665
1816
1978
—
—
Rpm
968
1004
1040
1077
1115
1153
1191
1230
1269
1309
1349
0.4
Bhp
0.55
0.63
0.71
0.81
0.91
1.03
1.15
1.29
1.43
1.59
1.76
1.4
Bhp
1.20
1.32
1.45
1.58
1.73
1.89
2.06
2.23
—
—
—
Rpm
1380
1411
1441
1473
1504
1536
1569
1602
—
—
—
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 2.40.
3. See general fan performance notes.
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
486
1069
0.68
600
1158
556
1103
0.76
678
1190
633
1137
0.86
763
1223
718
1172
0.96
856
1257
811
1208
1.08
957
1291
913
1244
1.20
1066
1326
1023
1281
1.33
1185
1361
1143
1318
1.48
1313
1397
1273
1355
1.63
1451
1433
1413
1393
1.80
1600
1470
1564
1431
1.98
1759
1506
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
1067
1445
1.34
1189
1506
1173
1474
1.46
1300
1535
1286
1505
1.60
1420
1565
1407
1535
1.74
1548
1595
1537
1567
1.90
1685
1626
1677
1598
2.06
1831
1657
1825
1630
2.24
1986
—
1984
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.8
Bhp
0.80
0.90
1.00
1.12
1.24
1.37
1.51
1.67
1.83
2.01
2.20
1.8
Bhp
1.48
1.61
1.75
1.90
2.06
2.24
—
—
—
—
—
Watts
715
800
892
993
1101
1219
1345
1481
1627
1784
1951
Watts
1312
1429
1555
1690
1833
1986
—
—
—
—
—
Rpm
1238
1269
1302
1334
1368
1401
1435
1470
1505
1540
—
Rpm
1564
1593
1622
1652
1682
—
—
—
—
—
—
1.0
Bhp
0.94
1.04
1.15
1.27
1.40
1.54
1.69
1.86
2.03
2.21
—
2.0
Bhp
1.62
1.76
1.91
2.06
2.23
—
—
—
—
—
—
Watts
831
922
1022
1130
1246
1371
1505
1649
1803
1967
—
Watts
1437
1560
1692
1833
1983
—
—
—
—
—
—
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 1035 to 1460 rpm. All other rpms require field-supplied
drive.
Table 22—Fan Performance 581B 060, 581C 060 — Vertical Discharge Units; High-Static Motor (Belt Drive)*
AIRFLOW
CFM
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
Rpm
848
887
927
967
1007
1048
1090
1131
1173
1215
1258
0.2
Bhp
0.42
0.49
0.57
0.65
0.75
0.85
0.97
1.09
1.23
1.38
1.54
Rpm
1312
1342
1374
1406
1438
1471
1504
1538
1572
1607
1642
1.2
Bhp
1.07
1.18
1.30
1.43
1.57
1.72
1.87
2.04
2.23
2.42
2.63
AIRFLOW
CFM
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
Watts
371
433
502
579
663
757
859
970
1091
1223
1365
Watts
948
1047
1153
1268
1391
1523
1665
1816
1978
2150
2333
Rpm
968
1004
1040
1077
1115
1153
1191
1230
1269
1309
1349
0.4
Bhp
0.55
0.63
0.71
0.81
0.91
1.03
1.15
1.29
1.43
1.59
1.76
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
486
1069
0.68
600
1158
556
1103
0.76
678
1190
633
1137
0.86
763
1223
718
1172
0.96
856
1257
811
1208
1.08
957
1291
913
1244
1.20
1066
1326
1023
1281
1.33
1185
1361
1143
1318
1.48
1313
1397
1273
1355
1.63
1451
1433
1413
1393
1.80
1600
1470
1564
1431
1.98
1759
1506
0.8
Bhp
0.80
0.90
1.00
1.12
1.24
1.37
1.51
1.67
1.83
2.01
2.20
Watts
715
800
892
993
1101
1219
1345
1481
1627
1784
1951
Rpm
1238
1269
1302
1334
1368
1401
1435
1470
1505
1540
1576
1.0
Bhp
0.94
1.04
1.15
1.27
1.40
1.54
1.69
1.86
2.03
2.21
2.41
Watts
831
922
1022
1130
1246
1371
1505
1649
1803
1967
2142
Rpm
1380
1411
1441
1473
1504
1536
1569
1602
1635
1669
1704
1.4
Bhp
1.20
1.32
1.45
1.58
1.73
1.89
2.06
2.23
2.42
2.63
2.84
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
1067
1445
1.34
1189
1506
1173
1474
1.46
1300
1535
1286
1505
1.60
1420
1565
1407
1535
1.74
1548
1595
1537
1567
1.90
1685
1626
1677
1598
2.06
1831
1657
1825
1630
2.24
1986
1688
1984
1663
2.42
2152
1720
2153
1695
2.62
2328
1753
2332
1729
2.83
2515
—
2523
—
—
—
—
1.8
Bhp
1.48
1.61
1.75
1.90
2.06
2.24
2.42
2.61
2.82
—
—
Watts
1312
1429
1555
1690
1833
1986
2149
2321
2504
—
—
Rpm
1564
1593
1622
1652
1682
1713
1744
1775
—
—
—
2.0
Bhp
1.62
1.76
1.91
2.06
2.23
2.41
2.60
2.81
—
—
—
Watts
1437
1560
1692
1833
1983
2142
2312
2491
—
—
—
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 2.90.
3. See general fan performance notes.
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 1300 to 1685 rpm. All other rpms require field-supplied drive.
32
Table 23—Fan Performance 581C 072 — Vertical Discharge Units; Standard Motor (Belt Drive)*
CFM
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
Rpm
967
1008
1049
1091
1133
1176
1218
1261
1305
1348
1392
1435
1479
AIRFLOW
CFM
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
Rpm
1406
1438
1470
1502
1535
1569
—
—
—
—
—
—
—
0.2
Bhp
0.63
0.72
0.82
0.93
1.05
1.18
1.32
1.47
1.63
1.80
1.99
2.19
2.40
1.2
Bhp
1.43
1.58
1.73
1.89
2.06
2.25
—
—
—
—
—
—
—
Watts
563
643
731
827
933
1047
1170
1304
1448
1602
1768
1945
2135
Watts
1273
1401
1537
1681
1834
1996
—
—
—
—
—
—
—
Rpm
1075
1112
1151
1189
1229
1268
1308
1349
1390
1431
1472
—
—
Rpm
1475
1505
1537
1568
1600
—
—
—
—
—
—
—
—
0.4
Bhp
0.80
0.91
1.02
1.14
1.26
1.40
1.55
1.72
1.89
2.07
2.27
—
—
1.4
Bhp
1.58
1.73
1.90
2.07
2.25
—
—
—
—
—
—
—
—
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 2.40.
3. See general fan performance notes.
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
715
1170
0.97
861
1255
805
1205
1.08
960
1289
903
1241
1.20
1068
1323
1008
1278
1.33
1183
1358
1123
1315
1.47
1308
1393
1247
1352
1.62
1441
1429
1380
1390
1.78
1584
1466
1523
1429
1.96
1736
1503
1677
1468
2.14
1900
1540
1841
1507
2.33
2073
—
2016
—
—
—
—
—
—
—
—
—
—
—
—
—
—
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
1403
1540
1.72
1531
1601
1541
1569
1.89
1678
1630
1686
1600
2.06
1833
1660
1840
1631
2.25
1996
—
2002
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.8
Bhp
1.13
1.25
1.38
1.52
1.67
1.84
2.01
2.19
2.38
—
—
—
—
1.8
Bhp
1.87
2.04
2.23
—
—
—
—
—
—
—
—
—
—
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
Watts
1002
1111
1228
1353
1487
1630
1782
1945
2117
—
—
—
—
Watts
1657
1813
1977
—
—
—
—
—
—
—
—
—
—
Rpm
1333
1366
1399
1433
1467
1501
1537
—
—
—
—
—
—
Rpm
1660
1689
1718
—
—
—
—
—
—
—
—
—
—
1.0
Bhp
1.28
1.42
1.56
1.71
1.87
2.04
2.23
—
—
—
—
—
—
2.0
Bhp
2.00
2.19
2.38
—
—
—
—
—
—
—
—
—
—
Watts
1139
1258
1384
1519
1662
1815
1977
—
—
—
—
—
—
Watts
1780
1945
2118
—
—
—
—
—
—
—
—
—
—
*Motor drive range: 1119 to 1585 rpm. All other rpms require field-supplied drive.
33
581B,C
AIRFLOW
Table 24—Fan Performance 581C 072 — Vertical Discharge Units; High-Static Motor (Belt Drive)*
AIRFLOW
581B,C
CFM
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
Rpm
967
1008
1049
1091
1133
1176
1218
1261
1305
1348
1392
1435
1479
0.2
Bhp
0.63
0.72
0.82
0.93
1.05
1.18
1.32
1.47
1.63
1.80
1.99
2.19
2.40
AIRFLOW
CFM
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
Rpm
1406
1438
1470
1502
1535
1569
1603
1638
1673
—
—
—
—
Watts
563
643
731
827
933
1047
1170
1304
1448
1602
1768
1945
2135
1.2
Bhp
1.43
1.58
1.73
1.89
2.06
2.25
2.44
2.64
2.86
—
—
—
—
Rpm
1075
1112
1151
1189
1229
1268
1308
1349
1390
1431
1472
1514
1556
Watts
1273
1401
1537
1681
1834
1996
2167
2349
2541
—
—
—
—
0.4
Bhp
0.80
0.91
1.02
1.14
1.26
1.40
1.55
1.72
1.89
2.07
2.27
2.48
2.70
Rpm
1475
1505
1537
1568
1600
1633
1666
1700
—
—
—
—
—
1.4
Bhp
1.58
1.73
1.90
2.07
2.25
2.45
2.65
2.87
—
—
—
—
—
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
715
1170
0.97
861
1255
805
1205
1.08
960
1289
903
1241
1.20
1068
1323
1008
1278
1.33
1183
1358
1123
1315
1.47
1308
1393
1247
1352
1.62
1441
1429
1380
1390
1.78
1584
1466
1523
1429
1.96
1736
1503
1677
1468
2.14
1900
1540
1841
1507
2.33
2073
1578
2016
1547
2.54
2258
1616
2203
1587
2.76
2455
—
2402
—
—
—
—
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
1403
1540
1.72
1531
1601
1541
1569
1.89
1678
1630
1686
1600
2.06
1833
1660
1840
1631
2.25
1996
1690
2002
1662
2.44
2167
1721
2174
1694
2.64
2348
1752
2355
1727
2.86
2539
—
2546
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.8
Bhp
1.13
1.25
1.38
1.52
1.67
1.84
2.01
2.19
2.38
2.59
2.81
—
—
1.8
Bhp
1.87
2.04
2.23
2.42
2.62
2.84
—
—
—
—
—
—
—
Watts
1002
1111
1228
1353
1487
1630
1782
1945
2117
2301
2495
—
—
Watts
1657
1813
1977
2149
2330
2520
—
—
—
—
—
—
—
Rpm
1333
1366
1399
1433
1467
1501
1537
1572
1608
1645
—
—
—
Rpm
1660
1689
1718
1747
1778
—
—
—
—
—
—
—
—
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 2.90.
3. See general fan performance notes.
600
700
800
900
1000
0.1
Rpm
Bhp
EXTERNAL STATIC PRESSURE (in. wg)
0.2
0.4
0.6
0.8
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
490
519
537
560
589
521
557
582
610
640
0.08
0.09
0.10
0.13
0.15
2.0
Bhp
2.00
2.19
2.38
2.59
2.80
—
—
—
—
—
—
—
—
Watts
1139
1258
1384
1519
1662
1815
1977
2149
2331
2524
—
—
—
Watts
1780
1945
2118
2300
2490
—
—
—
—
—
—
—
—
*Motor drive range: 1300 to 1685 rpm. All other rpms require field-supplied drive.
Table 25—Fan Performance 581B 024 — Horizontal Discharge Units; Standard Motor (Belt Drive)**
AIRFLOW
(Cfm)
1.0
Bhp
1.28
1.42
1.56
1.71
1.87
2.04
2.23
2.42
2.62
2.84
—
—
—
0.08
0.09
0.12
0.14
0.16
597
623
650
681
707
0.14
0.16
0.19
0.22
0.26
703
729
751
783
808
34
0.21
0.24
0.27
0.32
0.36
788
816
845
870
894
0.29
0.32
0.37
0.42
0.47
1.0
Rpm
868
892
927
947
971
Bhp
0.37
0.41
0.47
0.53
0.58
Table 26—Fan Performance 581B 036, 581C 036 — Horizontal Discharge Units; Standard Motor
(Belt Drive)*
CFM
900
1000
1100
1200
1300
1400
1500
Rpm
553
582
612
643
675
707
740
AIRFLOW
CFM
900
1000
1100
1200
1300
1400
1500
0.2
Bhp
0.14
0.16
0.20
0.23
0.28
0.33
0.38
1.2
Bhp
0.64
0.70
0.77
0.84
0.92
1.01
1.10
Rpm
1019
1042
1065
1089
1113
1138
1163
Watts
134
163
196
234
277
326
382
Watts
640
700
765
837
915
1000
1092
Rpm
681
707
734
762
790
819
849
Rpm
1084
1107
1130
1153
1177
1201
—
0.4
Bhp
0.22
0.26
0.30
0.34
0.40
0.45
0.52
1.4
Bhp
0.76
0.83
0.90
0.98
1.06
1.15
—
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 1.20.
3. See general fan performance notes.
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
221
782
0.32
316
870
257
807
0.36
358
894
297
833
0.41
405
919
343
859
0.46
458
944
394
886
0.52
517
969
452
913
0.58
581
996
515
941
0.66
653
1023
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
760
1146
0.89
885
1203
825
1168
0.96
956
1225
896
1190
1.04
1032
1247
974
1213
1.12
1115
—
1058
—
—
—
—
1149
—
—
—
—
—
—
—
—
—
0.8
Bhp
0.42
0.47
0.52
0.58
0.65
0.72
0.80
1.8
Bhp
1.02
1.10
1.18
—
—
—
—
Watts
417
466
519
579
644
716
795
Watts
1016
1091
1173
—
—
—
—
Rpm
948
971
995
1020
1044
1070
1096
Rpm
1258
—
—
—
—
—
—
1.0
Bhp
0.53
0.58
0.64
0.71
0.78
0.86
0.95
2.0
Bhp
1.16
—
—
—
—
—
—
Watts
526
580
639
705
777
855
941
Watts
1152
—
—
—
—
—
—
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 680 to 1044 rpm. All other rpms require field-supplied drive.
Table 27—Fan Performance 581B 036, 581C 036 — Horizontal Discharge Units; High-Static Motor
(Belt Drive)*
AIRFLOW
CFM
900
1000
1100
1200
1300
1400
1500
Rpm
553
582
612
643
675
707
740
0.2
Bhp
0.14
0.16
0.20
0.23
0.28
0.33
0.38
Rpm
1019
1042
1065
1089
1113
1138
1163
1.2
Bhp
0.64
0.70
0.77
0.84
0.92
1.01
1.10
AIRFLOW
CFM
900
1000
1100
1200
1300
1400
1500
Watts
134
163
196
234
277
326
382
Watts
640
700
765
837
915
1000
1092
Rpm
681
707
734
762
790
819
849
0.4
Bhp
0.22
0.26
0.30
0.34
0.40
0.45
0.52
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
221
782
0.32
316
870
257
807
0.36
358
894
297
833
0.41
405
919
343
859
0.46
458
944
394
886
0.52
517
969
452
913
0.58
581
996
515
941
0.66
653
1023
0.8
Bhp
0.42
0.47
0.52
0.58
0.65
0.72
0.80
Watts
417
466
519
579
644
716
795
Rpm
948
971
995
1020
1044
1070
1096
1.0
Bhp
0.53
0.58
0.64
0.71
0.78
0.86
0.95
Watts
526
580
639
705
777
855
941
Rpm
1084
1107
1130
1153
1177
1201
1226
1.4
Bhp
0.76
0.83
0.90
0.98
1.06
1.15
1.25
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
760
1146
0.89
885
1203
825
1168
0.96
956
1225
896
1190
1.04
1032
1247
974
1213
1.12
1115
1270
1058
1237
1.21
1205
1293
1149
1261
1.31
1303
1317
1247
1285
1.41
1407
1341
1.8
Bhp
1.02
1.10
1.18
1.27
1.36
1.47
1.58
Watts
1016
1091
1173
1262
1358
1461
1571
Rpm
1258
1279
1301
1324
1347
1370
1394
2.0
Bhp
1.16
1.24
1.33
1.42
1.52
1.63
1.75
Watts
1152
1232
1319
1413
1514
1623
1740
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 2.40.
3. See general fan performance notes.
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 1075 to 1455 rpm. All other rpms require field-supplied drive.
35
581B,C
AIRFLOW
Table 28—Fan Performance 581B 048, 581C 048 — Horizontal Discharge Units; Standard Motor
(Belt Drive)*
AIRFLOW
581B,C
CFM
1200
1300
1400
1500
1600
1700
1800
1900
2000
Rpm
643
675
707
740
773
807
841
875
910
AIRFLOW
CFM
1200
1300
1400
1500
1600
1700
1800
1900
2000
Rpm
1089
1113
1138
1163
1189
—
—
—
—
0.2
Bhp
0.23
0.28
0.33
0.38
0.45
0.52
0.59
0.68
0.77
1.2
Bhp
0.84
0.92
1.01
1.10
1.20
—
—
—
—
Watts
234
277
326
382
444
513
589
674
767
Watts
837
915
1000
1092
1191
—
—
—
—
Rpm
762
790
819
849
879
910
942
974
1006
0.4
Bhp
0.34
0.40
0.45
0.52
0.59
0.67
0.75
0.85
0.95
1.4
Bhp
0.98
1.06
1.15
—
—
—
—
—
—
Rpm
1153
1177
1201
—
—
—
—
—
—
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 1.20.
3. See general fan performance notes.
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
343
859
0.46
458
944
394
886
0.52
517
969
452
913
0.58
581
996
515
941
0.66
653
1023
586
970
0.73
731
1050
663
999
0.82
817
1078
749
1029
0.91
910
1106
842
1059
1.02
1012
1135
944
1090
1.13
1122
—
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
974
1213
1.12
1115
—
1058
—
—
—
—
1149
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.8
Bhp
0.58
0.65
0.72
0.80
0.88
0.98
1.08
1.19
—
1.8
Bhp
—
—
—
—
—
—
—
—
—
Watts
579
644
716
795
880
973
1074
1184
—
Watts
—
—
—
—
—
—
—
—
—
Rpm
1020
1044
1070
1096
1123
1150
—
—
—
Rpm
—
—
—
—
—
—
—
—
—
1.0
Bhp
0.71
0.78
0.86
0.95
1.04
1.14
—
—
—
2.0
Bhp
—
—
—
—
—
—
—
—
—
Watts
705
777
855
941
1034
1134
—
—
—
Watts
—
—
—
—
—
—
—
—
—
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 770 to 1185 rpm. All other rpms require field-supplied drive.
Table 29—Fan Performance 581B 048, 581C 048 — Horizontal Discharge Units; High-Static Motor
(Belt Drive)*
AIRFLOW
CFM
1200
1300
1400
1500
1600
1700
1800
1900
2000
Rpm
643
675
707
740
773
807
841
875
910
0.2
Bhp
0.23
0.28
0.33
0.38
0.45
0.52
0.59
0.68
0.77
Rpm
1089
1113
1138
1163
1189
1216
1242
1270
1297
1.2
Bhp
0.84
0.92
1.01
1.10
1.20
1.31
1.42
1.55
1.68
AIRFLOW
CFM
1200
1300
1400
1500
1600
1700
1800
1900
2000
Watts
234
277
326
382
444
513
589
674
767
Watts
837
915
1000
1092
1191
1299
1414
1538
1672
Rpm
762
790
819
849
879
910
942
974
1006
0.4
Bhp
0.34
0.40
0.45
0.52
0.59
0.67
0.75
0.85
0.95
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
343
859
0.46
458
944
394
886
0.52
517
969
452
913
0.58
581
996
515
941
0.66
653
1023
586
970
0.73
731
1050
663
999
0.82
817
1078
749
1029
0.91
910
1106
842
1059
1.02
1012
1135
944
1090
1.13
1122
1165
0.8
Bhp
0.58
0.65
0.72
0.80
0.88
0.98
1.08
1.19
1.31
Watts
579
644
716
795
880
973
1074
1184
1302
Rpm
1020
1044
1070
1096
1123
1150
1177
1205
1234
1.0
Bhp
0.71
0.78
0.86
0.95
1.04
1.14
1.25
1.37
1.49
Watts
705
777
855
941
1034
1134
1242
1360
1485
Rpm
1153
1177
1201
1226
1252
1277
1303
1330
1357
1.4
Bhp
0.98
1.06
1.15
1.25
1.36
1.48
1.60
1.73
1.87
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
974
1213
1.12
1115
1270
1058
1237
1.21
1205
1293
1149
1261
1.31
1303
1317
1247
1285
1.41
1407
1341
1353
1310
1.53
1520
1365
1468
1335
1.65
1640
1390
1590
1361
1.78
1770
1415
1721
1387
1.92
1908
1441
1862
1414
2.07
2055
1467
1.8
Bhp
1.27
1.36
1.47
1.58
1.70
1.83
1.96
2.11
2.26
Watts
1262
1358
1461
1571
1690
1817
1953
2098
2252
Rpm
1324
1347
1370
1394
1418
1442
1467
1493
—
2.0
Bhp
1.42
1.52
1.63
1.75
1.87
2.01
2.15
2.30
—
Watts
1413
1514
1623
1740
1865
1998
2140
2292
—
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 2.40.
3. See general fan performance notes.
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 1075 to 1455 rpm. All other rpms require field-supplied drive.
36
Table 30—Fan Performance 581B 060, 581C 060 Single-Phase — Horizontal Discharge Units;
Standard Motor (Belt Drive)*
CFM
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
Rpm
800
839
879
919
960
1001
1043
1085
1127
—
—
AIRFLOW
CFM
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
Rpm
1247
1270
1295
1321
—
—
—
—
—
—
—
0.2
Bhp
0.39
0.46
0.54
0.63
0.73
0.84
0.96
1.09
1.23
—
—
1.2
Bhp
0.98
1.07
1.17
1.28
—
—
—
—
—
—
—
Watts
350
412
483
561
648
744
850
966
1092
—
—
Watts
873
952
1040
1137
—
—
—
—
—
—
—
Rpm
904
938
974
1010
1047
1085
1123
1162
—
—
—
Rpm
1320
1342
—
—
—
—
—
—
—
—
—
0.4
Bhp
0.49
0.57
0.65
0.75
0.85
0.96
1.09
1.22
—
—
—
1.4
Bhp
1.13
1.22
—
—
—
—
—
—
—
—
—
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 1.30.
3. See general fan performance notes.
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
438
999
0.60
535
1087
505
1030
0.68
605
1115
580
1062
0.77
684
1144
663
1095
0.87
771
1174
754
1129
0.98
867
1206
855
1163
1.09
972
1238
965
1199
1.22
1086
—
1086
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
1002
1390
1.28
1137
—
1083
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.8
Bhp
0.72
0.80
0.90
1.00
1.11
1.23
—
—
—
—
—
1.8
Bhp
—
—
—
—
—
—
—
—
—
—
—
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
Watts
640
714
796
886
986
1095
—
—
—
—
—
Watts
—
—
—
—
—
—
—
—
—
—
—
Rpm
1169
1195
1221
1250
1279
—
—
—
—
—
—
Rpm
—
—
—
—
—
—
—
—
—
—
—
1.0
Bhp
0.85
0.93
1.03
1.14
1.25
—
—
—
—
—
—
2.0
Bhp
—
—
—
—
—
—
—
—
—
—
—
Watts
753
829
914
1008
1111
—
—
—
—
—
—
Watts
—
—
—
—
—
—
—
—
—
—
—
*Motor drive range: 1035 to 1460 rpm. All other rpms require field-supplied drive.
37
581B,C
AIRFLOW
Table 31—Fan Performance 581B 060, 581C 060 Three-Phase — Horizontal Discharge Units;
Standard Motor (Belt Drive)*
AIRFLOW
581B,C
CFM
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
Rpm
800
839
879
919
960
1001
1043
1085
1127
1169
1212
AIRFLOW
CFM
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
Rpm
1247
1270
1295
1321
1348
1377
1406
1437
1468
1500
1533
0.2
Bhp
0.39
0.46
0.54
0.63
0.73
0.84
0.96
1.09
1.23
1.38
1.55
1.2
Bhp
0.98
1.07
1.17
1.28
1.40
1.53
1.67
1.83
1.99
2.17
2.36
Watts
350
412
483
561
648
744
850
966
1092
1229
1378
Watts
873
952
1040
1137
1243
1359
1485
1621
1769
1928
2098
Rpm
904
938
974
1010
1047
1085
1123
1162
1201
1241
1281
0.4
Bhp
0.49
0.57
0.65
0.75
0.85
0.96
1.09
1.22
1.37
1.53
1.70
1.4
Bhp
1.13
1.22
1.32
1.43
1.56
1.69
1.83
1.99
2.16
2.35
—
Rpm
1320
1342
1365
1390
1415
1442
1470
1499
1529
1559
—
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 2.40.
3. See general fan performance notes.
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
438
999
0.60
535
1087
505
1030
0.68
605
1115
580
1062
0.77
684
1144
663
1095
0.87
771
1174
754
1129
0.98
867
1206
855
1163
1.09
972
1238
965
1199
1.22
1086
1271
1086
1235
1.36
1211
1305
1217
1272
1.52
1347
1340
1359
1310
1.68
1493
1375
1513
1348
1.86
1652
1412
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
1002
1390
1.28
1137
1457
1083
1411
1.37
1221
1476
1173
1432
1.48
1313
1497
1273
1455
1.59
1415
1518
1381
1479
1.72
1526
1541
1500
1505
1.86
1648
1565
1629
1531
2.00
1780
1591
1769
1559
2.16
1923
1617
1920
1587
2.34
2077
—
2083
—
—
—
—
—
—
—
—
—
0.8
Bhp
0.72
0.80
0.90
1.00
1.11
1.23
1.37
1.51
1.67
1.84
2.02
1.8
Bhp
1.44
1.54
1.64
1.76
1.89
2.03
2.18
2.34
—
—
—
Watts
640
714
796
886
986
1095
1213
1342
1482
1633
1796
Watts
1280
1365
1459
1563
1677
1801
1936
2082
—
—
—
Rpm
1169
1195
1221
1250
1279
1309
1340
1372
1405
1439
1473
Rpm
1522
1540
1559
1579
1601
1624
1648
—
—
—
—
1.0
Bhp
0.85
0.93
1.03
1.14
1.25
1.38
1.52
1.67
1.83
2.00
2.19
2.0
Bhp
1.61
1.71
1.82
1.93
2.06
2.21
2.36
—
—
—
—
Watts
753
829
914
1008
1111
1224
1346
1479
1623
1778
1945
Watts
1430
1517
1612
1718
1834
1961
2098
—
—
—
—
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 1035 to 1460 rpm. All other rpms require field-supplied drive.
Table 32—Fan Performance 581B 060, 581C 060 — Horizontal Discharge Units; High-Static Motor (Belt Drive)*
AIRFLOW
CFM
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
Rpm
800
839
879
919
960
1001
1043
1085
1127
1169
1212
0.2
Bhp
0.39
0.46
0.54
0.63
0.73
0.84
0.96
1.09
1.23
1.38
1.55
Rpm
1247
1270
1295
1321
1348
1377
1406
1437
1468
1500
1533
1.2
Bhp
0.98
1.07
1.17
1.28
1.40
1.53
1.67
1.83
1.99
2.17
2.36
AIRFLOW
CFM
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
Watts
350
412
483
561
648
744
850
966
1092
1229
1378
Watts
873
952
1040
1137
1243
1359
1485
1621
1769
1928
2098
Rpm
904
938
974
1010
1047
1085
1123
1162
1201
1241
1281
0.4
Bhp
0.49
0.57
0.65
0.75
0.85
0.96
1.09
1.22
1.37
1.53
1.70
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
438
999
0.60
535
1087
505
1030
0.68
605
1115
580
1062
0.77
684
1144
663
1095
0.87
771
1174
754
1129
0.98
867
1206
855
1163
1.09
972
1238
965
1199
1.22
1086
1271
1086
1235
1.36
1211
1305
1217
1272
1.52
1347
1340
1359
1310
1.68
1493
1375
1513
1348
1.86
1652
1412
0.8
Bhp
0.72
0.80
0.90
1.00
1.11
1.23
1.37
1.51
1.67
1.84
2.02
Watts
640
714
796
886
986
1095
1213
1342
1482
1633
1796
Rpm
1169
1195
1221
1250
1279
1309
1340
1372
1405
1439
1473
1.0
Bhp
0.85
0.93
1.03
1.14
1.25
1.38
1.52
1.67
1.83
2.00
2.19
Watts
753
829
914
1008
1111
1224
1346
1479
1623
1778
1945
Rpm
1320
1342
1365
1390
1415
1442
1470
1499
1529
1559
1591
1.4
Bhp
1.13
1.22
1.32
1.43
1.56
1.69
1.83
1.99
2.16
2.35
2.54
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
1002
1390
1.28
1137
1457
1083
1411
1.37
1221
1476
1173
1432
1.48
1313
1497
1273
1455
1.59
1415
1518
1381
1479
1.72
1526
1541
1500
1505
1.86
1648
1565
1629
1531
2.00
1780
1591
1769
1559
2.16
1923
1617
1920
1587
2.34
2077
1644
2083
1616
2.53
2243
1672
2257
1647
2.73
2421
—
1.8
Bhp
1.44
1.54
1.64
1.76
1.89
2.03
2.18
2.34
2.52
2.71
—
Watts
1280
1365
1459
1563
1677
1801
1936
2082
2239
2408
—
Rpm
1522
1540
1559
1579
1601
1624
1648
1673
1699
1726
—
2.0
Bhp
1.61
1.71
1.82
1.93
2.06
2.21
2.36
2.53
2.71
2.90
—
Watts
1430
1517
1612
1718
1834
1961
2098
2246
2406
2579
—
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 2.90.
3. See general fan performance notes.
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 1300 to 1685 rpm. All other rpms require field-supplied drive.
38
Table 33—Fan Performance 581B 072 — Horizontal Discharge Units; Standard Motor (Belt Drive)*
CFM
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
Rpm
913
952
992
1032
1073
1114
1155
1196
1238
1280
1322
1364
—
AIRFLOW
CFM
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
Rpm
1322
1351
1380
1411
1441
1473
—
—
—
—
—
—
—
0.2
Bhp
0.64
0.73
0.84
0.95
1.07
1.21
1.36
1.51
1.69
1.87
2.07
2.28
—
1.2
Bhp
1.56
1.68
1.82
1.97
2.13
2.30
—
—
—
—
—
—
—
Watts
569
652
744
844
954
1074
1204
1345
1497
1660
1835
2023
—
Watts
1382
1495
1617
1748
1890
2041
—
—
—
—
—
—
—
Rpm
1010
1046
1083
1120
1158
1196
1234
1273
1312
1352
1392
—
—
Rpm
1388
1416
1444
1473
1503
—
—
—
—
—
—
—
—
0.4
Bhp
0.80
0.91
1.02
1.14
1.27
1.41
1.57
1.73
1.91
2.10
2.31
—
—
1.4
Bhp
1.77
1.90
2.04
2.20
2.36
—
—
—
—
—
—
—
—
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 2.40.
3. See general fan performance notes.
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
715
1098
0.98
869
1178
805
1131
1.09
965
1210
903
1166
1.21
1070
1242
1010
1200
1.33
1184
1275
1127
1236
1.47
1307
1308
1254
1272
1.62
1440
1343
1391
1308
1.78
1584
1377
1538
1345
1.96
1738
1412
1697
1382
2.14
1904
1448
1867
1420
2.34
2081
—
2050
—
—
—
—
—
—
—
—
—
—
—
—
—
—
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
1568
1451
1.98
1762
1510
1686
1477
2.12
1885
1536
1814
1505
2.27
2017
—
1950
—
—
—
—
2097
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.8
Bhp
1.16
1.28
1.40
1.54
1.68
1.84
2.01
2.19
2.38
—
—
—
—
1.8
Bhp
2.21
2.35
—
—
—
—
—
—
—
—
—
—
—
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
Watts
1032
1134
1245
1365
1495
1634
1784
1945
2117
—
—
—
—
Watts
1962
2090
—
—
—
—
—
—
—
—
—
—
—
Rpm
1252
1282
1313
1345
1377
1409
1443
—
—
—
—
—
—
Rpm
—
—
—
—
—
—
—
—
—
—
—
—
—
1.0
Bhp
1.35
1.48
1.61
1.75
1.90
2.07
2.24
—
—
—
—
—
—
2.0
Bhp
—
—
—
—
—
—
—
—
—
—
—
—
—
Watts
1203
1311
1427
1553
1689
1834
1990
—
—
—
—
—
—
581B,C
AIRFLOW
Watts
—
—
—
—
—
—
—
—
—
—
—
—
—
*Motor drive range: 1119 to 1585 rpm. All other rpms require field-supplied drive.
39
Table 34—Fan Performance 581B 072 — Horizontal Discharge Units; High-Static Motor (Belt Drive)*
AIRFLOW
581B,C
CFM
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
Rpm
913
952
992
1032
1073
1114
1155
1196
1238
1280
1322
1364
1406
0.2
Bhp
0.64
0.73
0.84
0.95
1.07
1.21
1.36
1.51
1.69
1.87
2.07
2.28
2.50
Rpm
1322
1351
1380
1411
1441
1473
1505
1537
1571
—
—
—
—
1.2
Bhp
1.56
1.68
1.82
1.97
2.13
2.30
2.48
2.68
2.88
—
—
—
—
AIRFLOW
CFM
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
Watts
569
652
744
844
954
1074
1204
1345
1497
1660
1835
2023
2224
Watts
1382
1495
1617
1748
1890
2041
2203
2376
2560
—
—
—
—
Rpm
1010
1046
1083
1120
1158
1196
1234
1273
1312
1352
1392
1432
1472
0.4
Bhp
0.80
0.91
1.02
1.14
1.27
1.41
1.57
1.73
1.91
2.10
2.31
2.53
2.76
EXTERNAL STATIC PRESSURE (in. wg)
0.6
Watts Rpm
Bhp
Watts
Rpm
715
1098
0.98
869
1178
805
1131
1.09
965
1210
903
1166
1.21
1070
1242
1010
1200
1.33
1184
1275
1127
1236
1.47
1307
1308
1254
1272
1.62
1440
1343
1391
1308
1.78
1584
1377
1538
1345
1.96
1738
1412
1697
1382
2.14
1904
1448
1867
1420
2.34
2081
1484
2050
1458
2.56
2270
1521
2245
1496
2.78
2472
—
2452
—
—
—
—
0.8
Bhp
1.16
1.28
1.40
1.54
1.68
1.84
2.01
2.19
2.38
2.59
2.81
—
—
Watts
1032
1134
1245
1365
1495
1634
1784
1945
2117
2300
2496
—
—
Rpm
1252
1282
1313
1345
1377
1409
1443
1477
1511
1546
—
—
—
1.0
Bhp
1.35
1.48
1.61
1.75
1.90
2.07
2.24
2.43
2.63
2.84
—
—
—
Watts
1203
1311
1427
1553
1689
1834
1990
2157
2335
2526
—
—
—
Rpm
1388
1416
1444
1473
1503
1533
1564
—
—
—
—
—
—
1.4
Bhp
1.77
1.90
2.04
2.20
2.36
2.54
2.73
—
—
—
—
—
—
EXTERNAL STATIC PRESSURE (in. wg)
1.6
Watts Rpm
Bhp
Watts
Rpm
1568
1451
1.98
1762
1510
1686
1477
2.12
1885
1536
1814
1505
2.27
2017
1563
1950
1533
2.43
2159
1590
2097
1562
2.60
2311
1618
2254
1591
2.79
2474
—
2422
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.8
Bhp
2.21
2.35
2.51
2.67
2.85
—
—
—
—
—
—
—
—
Watts
1962
2090
2227
2374
2532
—
—
—
—
—
—
—
—
Rpm
1568
1593
1619
—
—
—
—
—
—
—
—
—
—
2.0
Bhp
2.44
2.59
2.75
—
—
—
—
—
—
—
—
—
—
Watts
2169
2302
2443
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Grey cells indicate field-supplied drive is required.
2. Maximum continuous bhp is 2.90.
3. See general fan performance notes.
LEGEND
Bhp — Brake Horsepower
Watts — Input Watts to Motor
*Motor drive range: 1300 to 1685 rpm. All other rpms require field-supplied drive.
40
PRE-START-UP
WARNING
START-UP
FIRE, EXPLOSION, ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal
injury, death and/or property damage:
1. Follow recognized safety practices and wear
protective goggles when checking or servicing a
refrigerant system.
2. Do not operate the compressor or provide any
electric power to the unit unless the compressor terminal
cover is in place and secured.
3. Do not remove the compressor terminal cover until
all electrical sources are disconnected and tagged with
lockout tags.
4. Relieve all pressure from the system before touching
or disturbing anything inside the terminal box if a
refrigerant leak is suspected around the compressor
terminals. Use accepted methods to recover the
refrigerant.
5. Never attempt to repair a soldered connection while
the refrigerant system is under pressure.
6. Do not use a torch to remove any component. The
system contains oil and refrigerant under pressure. To
remove a component, wear protective goggles and
proceed as follows:
a. Shut off electrical power to the unit and tag
disconnect.
b. Recover refrigerant to relieve all pressure
from the system using both high-pressure
and low-pressure ports.
c. Cut component connection tubing with a
tubing cutter, and remove the component
from the unit.
d. Carefully unsweat the remaining tubing
stubs when necessary. Oil can ignite when
exposed to a torch flame.
Proceed as follows to inspect and prepare the unit for initial
start-up:
1. Remove all access panels.
2. Read and follow instructions on all WARNING,
CAUTION, and INFORMATION labels attached to, or
shipped with, unit.
3. Make the following inspections:
a. Inspect for shipping and handling damages such as
broken lines, loose parts, or disconnected wires, etc.
b. Inspect for oil at all refrigerant tubing connections and on
unit base. Detecting oil generally indicates a refrigerant
leak. Leak-test all refrigerant tubing connections using
electronic leak detector, halide torch, or liquid-soap
solution.
c. Inspect all field-wiring and factory-wiring connections.
Be sure that connections are completed and tight. Be sure
that wires are not in contact with refrigerant tubing or
sharp edges.
d. Inspect coil fins. If damaged during shipping and
handling, carefully straighten fins with a fin comb.
4. Verify the following conditions:
a. Make sure that condenser-fan blade are correctly
positioned in fan orifice. See Condenser-Fan Adjustment
section for more details.
b. Make sure that air filter(s) is in place.
Unit Preparation
Make sure that the unit has been installed in accordance with
installation instructions and applicable codes.
Gas Piping
Check gas piping for leaks.
!
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could cause personal
injury or death.
Disconnect gas piping from unit when leak testing at
pressure greater than 1/2 psig. Pressures greater than 1/2
psig will cause gas valve damage resulting in hazardous
condition. If gas valve is subjected to pressure greater
than 1/2 psig, it must be replaced before use. When
pressure testing field-supplied gas piping at pressures of
1/ psig or less, a unit connected to such piping must be
2
isolated by manually closing the gas valve.
Return--Air Filters
Make sure the correct filters are installed in the unit (See Table 1
or 2). Do not operate the unit without return-air filters.
Outdoor--Air Inlet Screens
Outdoor-air inlet screen(s) must be in place before operating the
unit.
Compressor Mounting
Compressors are internally spring mounted. Do not loosen or
remove the compressor holddown bolts.
Internal Wiring
Check all electrical connections in unit control boxes; tighten
them as required.
Refrigerant Service Ports
Each unit system has 4 Schrader--type service ports: one on the
suction line, one on the liquid line, and 2 on the compressor
discharge line. Be sure that caps on the ports are tight. Two
additional Schrader valves are located under the high--pressure
and low--pressure switches, respectively.
High Flow Refrigerant Valves
Two high flow valves are located on the hot gas tube coming out
of the compressor and the suction tube going into the compressor.
Large black plastic caps identify these valves. These valves have
O--rings inside which screw the cap onto a brass body to prevent
leaks. No field access to these valves is available at this time.
Ensure the plastic caps remain on the valves and are tight or the
possibility of refrigerant leakage could occur.
41
581B,C
!
c. Make sure that condensate drain trap is filled with water
to ensure proper drainage.
d. Make sure that all tools and miscellaneous loose parts
have been removed.
581B,C
Compressor Rotation
Table 35—Altitude Compensation*
581B 036--072, 581C 024--060 Standard Units
On 3-phase units be certain that the compressor is rotating in the
proper direction. To determine whether or not compressor is
rotating in the proper direction:
1. Connect the service gauges to suction and discharge
pressure fittings.
2. Energize the compressor.
3. The suction pressure should drop and the discharge
pressure should rise, as is normal on any start-up.
If the suction pressure does not drop and the discharge pressure
does not rise to normal levels:
1. Note that the indoor fan (006 and 007 three-phase units
only) is probably also rotating in the wrong direction.
2. Turn off power to the unit and tag disconnect.
3. Reverse any two of the unit power leads.
4. Turn on power to the unit and energize the compressor.
The suction and discharge pressure levels should now move to
their normal start-up levels.
NOTE: When the compressor is rotating in the wrong direction,
the unit makes more noise and does not provide cooling.
Cooling
Set the space thermostat to the OFF position. Set the system
selector switch at COOL position and the fan switch at AUTO
position. Adjust the thermostat to a setting below room
temperature. The compressor starts when contactor closes.
Check the unit charge. Refer to Refrigerant Charge section.
Reset the thermostat at a position above room temperature. The
compressor will shut off. Evaporator fan will shut off after a
30--second delay.
To Shut Off Unit -- Set the system selector switch at OFF
position. Resetting the thermostat at a position above room
temperature shuts off the unit temporarily until the space
temperature exceeds the thermostat setting. Units are equipped
with a Cycle-LOC™ protection device. The unit shuts down on
any safety trip and remains off; an indicator light on the
thermostat comes on. Check the reason for the safety trip.
ELEVATION
(ft)
0-2,000
2,000
3,000
4,000
5,000
6,000
7,000
8,000
9,000
10,000
11,000
12,000
13,000
14,000
33
36
36
37
38
40
41
42
43
44
45
46
47
48
43
44
45
45
46
47
48
49
50
50
51
52
52
53
150,000 BTUH
NOMINAL INPUT
Natural
Gas
Orifice
Size†
Liquid
Propane
Orifice
Size†
30
31
31
32
32
34
35
36
37
39
41
42
43
44
37
39
40
41
42
43
43
44
45
46
47
48
49
50
*As the height above sea level increases, there is less oxygen per cubic
foot of air. Therefore, heat input rate should be reduced at higher altitudes.
†Orifices available through your Bryant distributor.
Table 36—Altitude Compensation* —
581B 036--072, 581C 024--060 Low NOx Units
ELEVATION
(ft)
0-2,000
2,000
3,000
4,000
5,000
6,000
7,000
8,000
9,000
10,000
11,000
12,000
13,000
14,000
Main Burners
Main burners are factory set and should require no adjustment.
TO CHECK ignition of main burners and heating controls, move
thermostat set point above room temperature and verify that the
burners light and evaporator fan is energized. Check heating
effect, then lower the thermostat setting below the room
temperature and verify that the burners and evaporator fan turn
off.
Refer to Tables 35 and 36 for the correct orifice to use at high
altitudes.
72,000 AND
115,000
115
000 BTUH
NOMINAL INPUT
Natural
Liquid
Gas
Propane
Orifice
Orifice
Size†
Size†
60,000 AND
90,000 BTUH
NOMINAL INPUT
Natural
Liquid
Gas
Propane
Orifice
Orifice
Size†
Size†
38
40
41
42
43
43
44
45
46
47
48
49
50
51
45
47
48
49
49
50
50
51
52
52
53
53
54
54
120,000 BTUH
NOMINAL INPUT
Natural
Gas
Orifice
Size
Liquid
Propane
Orifice
Size†
32
33
35
36
37
38
39
41
42
43
44
44
46
47
42
43
43
44
45
45
46
47
48
49
50
51
52
52
*As the height above sea level increases, there is less oxygen per cubic
foot of air. Therefore, the input rate should be reduced at higher altitudes.
†Orifices are available through your local Bryant distributor.
42
Operating Sequence
1. Purge gas supply line of air by opening union ahead of the
gas valve. If gas odor is detected, tighten union and wait 5
minutes before proceeding.
2. Turn on electrical supply and manual gas valve.
3. Set system switch selector at HEAT position and fan
switch at AUTO or ON position. Set heating temperature
lever above room temperature.
4. The induced-draft motor will start.
5. After a call for heating, the main burners should light
within 5 seconds. If the burner does not light, then there is
a 22-second delay before another 5-second try. If the
burner still does not light, the time delay is repeated. If the
burner does not light within 15 minutes, there is a lockout.
To reset the control, break the 24 v power to W1.
6. The evaporator-fan motor will turn on 45 seconds after
burner ignition.
7. The evaporator-fan motor will turn off in 45 seconds after
the thermostat temperature is satisfied.
8. Adjust airflow to obtain a temperature rise within the
range specified on the unit nameplate.
NOTE: The default value for the evaporator-fan motor on/off
delay is 45 seconds. The Integrated Gas Unit Controller (IGC)
modifies this value when abnormal limit switch cycles occur.
Based upon unit operating conditions, the on delay can be
reduced to 0 seconds and the off delay can be extended to
180
seconds. When one flash of the LED (light-emitting diode) is
observed, the evaporator-fan on/off delay has been modified.
If the limit switch trips at the start of the heating cycle during the
evaporator on delay, the time period of the on delay for the next
cycle will be 5 seconds less than the time at which the switch
tripped. (Example: If the limit switch trips at 30 seconds, the
evaporator-fan on delay for the next cycle will occur at 25
seconds.) To prevent short-cycling, a 5-second reduction will
only occur if a minimum of 10 minutes has elapsed since the last
call for heating.
The evaporator-fan off delay can also be modified. Once the call
for heating has ended, there is a 10-minute period during which
the modification can occur. If the limit switch trips during this
period, the evaporator-fan off delay will increase by 15 seconds.
A maximum of 9 trips can occur, extending the evaporator-fan off
delay to 180 seconds.
To restore the original default value, reset the power to the unit.
To Shut Off Unit —Set system selector switch at off position.
Resetting heating selector lever below room temperature will
temporarily shut unit off until space temperature falls below
thermostat setting.
Cooling -- Units Without Economizer
When thermostat calls for cooling, terminals G and Y1 are
energized. The indoor-fan contactor (IFC), reversing valve
solenoid (RVS) and compressor contactor are energized and
indoor-fan motor, compressor, and outdoor fan starts. The
outdoor fan motor runs continuously while unit is cooling.
Heating -- Units Without Economizer
When the thermostat calls for heating, terminal W1 is energized.
To prevent thermostat short--cycling, the unit is locked into the
Heating mode for at least 1 minute when W1 is energized. The
induced--draft motor is energized and the burner ignition
sequence begins. The indoor (evaporator) fan motor (IFM) is
energized 45 seconds after a flame is ignited. On units equipped
for two stages of heat, when additional heat is needed, W2 is
energized and the high--fire solenoid on the main gas valve
(MGV) is energized. When the thermostat is satisfied and W1 is
deenergized, the IFM stops after a 45--second time--off delay.
Cooling -- Units With Economi$er IV
When free cooling is not available, the compressors will be
controlled by the zone thermostat. When free cooling is available,
the outdoor-air damper is modulated by the EconoMi$er IV
control to provide a 50_ to 55_F supply-air temperature into the
zone. As the supply-air temperature fluctuates above 55_ or
below 50_F, the dampers will be modulated (open or close) to
bring the supply-air temperature back within the set point limits.
Integrated EconoMi$er IV operation on single-stage units
requires a 2-stage thermostat (Y1 and Y2).
For EconoMi$er IV operation, there must be a thermostat call for
the fan (G). This will move the damper to its minimum position
during the occupied mode.
If the increase in cooling capacity causes the supply--air
temperature to drop below 45_F, then the outdoor--air damper
position will be fully closed. If the supply--air temperature
continues to fall, the outdoor--air damper will close. Control
returns to normal once the supply--air temperature rises above
48_F.
If optional power exhaust is installed, as the outdoor--air damper
opens and closes, the power exhaust fans will be energized and
deenergized.
If field--installed accessory CO2 sensors are connected to the
EconoMi$er IV control, a demand controlled ventilation strategy
will begin to operate. As the CO2 level in the zone increases
above the CO2 set point, the minimum position of the damper
will be increased proportionally. As the CO2 level decreases
because of the increase in fresh air, the outdoor--air damper will
be proportionally closed. Damper position will follow the higher
demand condition from DCV mode or free cooling mode.
Damper movement from full closed to full open (or vice versa)
will take between 1--1/2 and 2--1/2 minutes.
If free cooling can be used as determined from the appropriate
changeover command (switch, dry bulb, enthalpy curve,
differential dry bulb, or differential enthalpy), a call for cooling
(Y1 closes at the thermostat) will cause the control to modulate
the dampers open to maintain the supply air temperature set point
at 50_ to 55_F.
As the supply air temperature drops below the set point range of
50_ to 55_F, the control will modulate the outdoor--air dampers
closed to maintain the proper supply--air temperature.
Safety Relief
A soft solder joint at the suction line fitting provides pressure
relief under abnormal temperature and pressure conditions.
Ventilation (Continuous Fan)
Set fan and system selector switches at ON and OFF positions,
respectively. Evaporator fan operates continuously to provide
constant air circulation. When the evaporator--fan selector switch
is turned to the OFF position, there is a 30--second delay before
the fan turns off.
43
581B,C
Heating
581B,C
Heating -- Units With Economi$er IV
When the room temperature calls for heat, the heating controls are
energized as described in the Heating, Units Without Economizer
section. During the occupied mode, whenever the indoor fan
contactor is energized, the economizer damper moves to the
minimum position.
Units With Perfect Humidity™ Adaptive
Dehumidification System
Normal Design Operation
When the rooftop operates under the normal sequence of
operation, the compressors will cycle to maintain indoor
conditions. (See Fig. 44.)
The Perfect Humidity adaptive dehumidification system includes
a factory-installed Motormaster® low ambient control to keep the
head and suction pressure high, allowing normal design cooling
mode operation down to 0°F.
Subcooling Mode
When subcooling mode is initiated, this will energize (close) the
liquid line solenoid valve (LLSV) forcing the hot liquid
refrigerant to enter into the subcooling coil. (See Fig. 45.)
As the hot liquid refrigerant passes through the subcooling/ reheat
dehumidification coil, it is exposed to the cold supply airflow
coming through the evaporator coil. The liquid is further
subcooled to a temperature approaching the evaporator
leaving-air temperature. The liquid then enters a thermostatic
expansion valve (TXV) where the liquid drops to a lower
pressure. The TXV does not have a pressure drop great enough to
change the liquid to a 2-phase fluid, so the liquid then enters the
Acutrol™ device at the evaporator coil.
The liquid enters the evaporator coil at a temperature lower than
in standard cooling operation. This lower temperature increases
the latent capacity of the rooftop unit. The refrigerant passes
through the evaporator and is turned into a vapor. The air passing
over the evaporator coil will become colder than during normal
operation. However, as this same air passes over the subcooling
coil, it will be slightly warmed, partially reheating the air.
Subcooling mode operates only when the outside air
temperature is warmer than 40_F. A factory-installed temperature
switch located in the condenser section will lock out subcooling
mode when the outside temperature is cooler than 40_F.
The scroll compressors are equipped with crankcase heaters to
provide protection for the compressors due to the additional
refrigerant charge required by the subcooling/reheat coil.
When in subcooling mode, there is a slight decrease in system
total gross capacity (5% less), a lower gross sensible capacity
(20% less), and a greatly increased latent capacity (up to 40%
more).
Hot Gas Reheat Mode
When the humidity levels in the space require humidity control, a
hot gas solenoid valve (specific to hot gas reheat mode only) will
open to bypass a portion of hot gas refrigerant around the
condenser coil. (See Fig. 46.)
This hot gas will mix with liquid refrigerant leaving the
condenser coil and flow to the subcooling/reheat
dehumidification coil. Now the conditioned air coming off the
evaporator will be cooled and dehumidified, but will be warmed
to neutral conditions (72_F to 75_F) by the subcooling/reheat
dehumidification coil.
Fig. 44 --- Perfect Humidityt Normal
Design Cooling Operation
Fig. 45 --- Perfect Humidity Subcooling
Mode Operation
Fig. 46 --- Perfect Humidity Hot Gas
Reheat Mode Operation
C06135
C06136
C06137
See Table 37 for the Perfect Humidity adaptive dehumidification
system sequence of operation.
44
Table 37—Perfect Humidity Adaptive Dehumidification System Sequence of Operation and
System Response — Single Compressor Unit (581C 024--060, 581B 036--072)
THERMOSTAT INPUT
H
Off
On
On
On
On
On
Y1
ECONOMIZER FUNCTION
Y2
—
On
On
On
On
Off
OAT. < Economizer Set Point
581B,C UNIT OPERATION
Economizer
Comp. 1
Subcooling Mode
Hot Gas Reheat Mode
Normal Operation
—
On
Off
On
Off
Off
No
No
Yes
Yes
No
Off
Off
On
On
Off
On
On
On
On
On
Yes
Yes
Yes
No
No
No
No
No
Yes
Yes
The net effect of the rooftop when in hot gas reheat mode is to
provide nearly all latent capacity removal from the space when
sensible loads diminish (when outdoor temperature conditions are
moderate). When in hot gas reheat mode, the unit will operate to
provide mostly latent capacity and extremely low sensible heat
ratio capability.
Similar to the subcooling mode of operation, hot gas reheat mode
operates only when the outside air temperature is warmer than
40_F. Below this temperature, a factory installed outside air
temperature switch will lockout this mode of operation.
SERVICE
!
One--Row Coils
Wash coil with commercial coil cleaner. It is not necessary to
remove top panel.
2-Row Coils
Clean coil as follows:
1. Turn off unit power, tag disconnect.
2. Remove top panel screws on condenser end of unit.
3. Remove condenser coil corner post. (See Fig. 47.) To hold
top panel open, place coil corner post between top panel
and center post. (See Fig. 48.)
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could cause personal
injury or death.
When sevicing unit, shut off all electrical power to unit
and install lockout tag.
Step 1 —Cleaning
Inspect unit interior at the beginning of heating and cooling
season and as operating conditions require.
Evaporator Coil
1. Turn unit power off, tag disconnect. Remove evaporator
coil access panel.
2. If economizer or two-position damper is installed, remove
economizer by disconnecting Molex plug and
removing mounting screws.
3. Slide filters out of unit.
4. Clean coil using a commercial coil cleaner or dishwasher
detergent in a pressurized spray canister. Wash both sides
of coil and flush with clean water. For best results,
back-flush toward return-air section to remove foreign
material. Flush condensate pan after completion.
5. Reinstall economizer and filters.
6. Reconnect wiring.
7. Replace access panels.
Condenser Coil
Inspect coil monthly. Clean condenser coil annually, and as
required by location and outdoor air conditions.
Fig. 47 --- Cleaning Condenser Coil
Fig. 48 --- Propping Up Top Panel
45
C06044
C06045
581B,C
NOTE: On a thermostat call for W1, all cooling and dehumidification will be off.
LEGEND
OAT --- Outdoor Air Temperature
UNIT
FAN HEIGHT (in.) - A
024-060 and 072 (208/230 v)
072 (460 v)
2.75
3.50
581B,C
Fig. 50 --- Condenser--Fan Adjustment
C06138
Step 4 —EconoMi$er IV Adjustment
Refer to Optional EconoMi$er IV section.
Fig. 49 --- Separating Coil Sections
C06046
4. Remove screws securing coil to compressor plate and
compressor access panel.
5. Remove fastener holding coil sections together at return
end of condenser coil. Carefully separate the outer coil
section 3 to 4 in. from the inner coil section. (See Fig. 49.)
6. Use a water hose or other suitable equipment to flush
down between the 2 coil sections to remove dirt and
debris. Clean the outer surfaces with a stiff brush in the
normal manner.
7. Secure inner and outer coil rows together with a
field-supplied fastener.
8. Reposition the outer coil section and remove the coil
corner post from between the top panel and center post.
Reinstall the coil corner post and replace all screws.
Condensate Drain
Check and clean each year at the start of the cooling season. In
winter, keep the drain dry or protect it against freeze-up.
Filters
Clean or replace at the start of each heating and cooling season, or
more often if operating conditions require it. Replacement filters
must be the same dimensions as the original filters.
Outdoor--Air Inlet Screens
Clean the screens with steam or hot water and a mild detergent.
Do not use disposable filters in place of screens.
Step 2 —Lubrication
Compressor
The compressor is charged with the correct amount of oil at the
factory.
Fan Motor Bearings
Fan motor bearings are permanently lubricated. No further
lubrication is required. No lubrication of condenser-fan or
evaporator-fan motors is required.
Step 5 —Evaporator Fan Belt Inspection
Check condition of evaporator belt or tension during heating and
cooling inspections or as conditions require. Replace belt or
adjust as necessary.
Step 6 —High Pressure Switch
The high-pressure switch contains a Schrader core depressor, and
is located on the compressor hot gas line. This switch opens at
428 psig and closes at 320 psig. No adjustments are necessary.
Step 7 —Loss--of--Charge Switch
The loss-of-charge switch contains a Schrader core depressor, and
is located on the compressor liquid line. This switch opens at 7
psig and closes at 22 psig. No adjustments are necessary.
Step 8 —Freeze--Stat
The freeze-stat is a bimetal temperature-sensing switch that is
located on the “hair-pin” end of the evaporator coil. The switch
protects the evaporator coil from freeze-up due to lack of airflow.
The switch opens at 30_F and closes at 45_F. No adjustments are
necessary.
Step 9 —Refrigerant Charge
Amount of refrigerant charge is listed on unit nameplate (also
refer to Table 1). Refer to HVAC Servicing Procedures literature
available at your local distributor and the following procedures.
Unit panels must be in place when unit is operating during
charging procedure. Unit must operate a minimum of 10 minutes
before checking or adjusting refrigerant charge.
An accurate superheat, thermocouple-type or thermistor-type
thermometer, and a gauge manifold are required when using the
superheat charging method for evaluating the unit charge. Do not
use mercury or small dial-type thermometers because they are not
adequate for this type of measurement.
No Charge
Use standard evacuating techniques. After evacuating system to
500 microns, weigh in the specified amount of refrigerant. (Refer
to Table 1 or 2 and unit information plate.)
Step 3 —Condenser--Fan Adjustment
Shut off unit power supply. Remove condenser-fan assembly
(grille, motor, motor cover, and fan) and loosen fan hub
setscrews. Adjust fan height as shown in Fig. 50. Tighten
setscrews and replace condenser-fan assembly.
46
Fig. 51 --- Cooling Charging Chart,
Standard 581B 036
581B,C
Low Charge Cooling
Using Cooling Charging Charts, Fig. 51--54 and 59--62, vary
refrigerant until the conditions of the charts are met. Note the
charging charts are different from type normally used. Charts are
based on charging the units to the correct superheat for the
various operating conditions. Accurate pressure gauge and
temperature sensing device are required. Connect the pressure
gauge to the service port on the suction line. Mount the
temperature sensing device on the suction line and insulate it so
that outdoor ambient temperature does not affect the reading.
Indoor-air cfm must be within the normal operating range of the
unit.
Perfect Humidity™ System Charging
The system charge for units with the Perfect Humidity adaptive
dehumidification system is greater than that of the standard unit
alone. The charge for units with this option is indicated on the
unit nameplate drawing. Also refer to Fig. 55--58. To charge
systems using the Perfect Humidity adaptive dehumidification
system, fully evacuate, recover, and recharge the system to the
nameplate specified charge level. To check or adjust refrigerant
charge on systems using the Perfect Humidity adaptive
dehumidification system, charge per Fig. 55--58.
Fig. 52 --- Cooling Charging Chart,
Standard 581B 048
C06140
C06139
Fig. 53 --- Cooling Charging Chart,
Standard 581B 060
47
C06141
581B,C
Fig. 54 --- Cooling Charging Chart,
Standard 581B 072
C06142
C06144
Fig. 56 --- Cooling Charging Chart, 581B 048 with
Optional Perfect Humidity Adaptive Dehumidification
System
NOTE: When using the charging charts, it is important that only
the subcooling/reheat dehumidification coil liquid line solenoid
valve be energized. The subcooling/reheat dehumidification coil
liquid line solenoid valve MUST be energized to use the charging
charts and the outdoor motor speed controller jumpered to run the
fan at full speed.
The charts reference a liquid pressure (psig) and temperature at a
point between the condenser coil and the subcooling/reheat
dehumidification coil. A tap is provided on the unit to measure
liquid pressure entering the subcooling/reheat dehumidification
coil.
IMPORTANT: The subcooling mode charging charts (Fig.
55--58) are to be used ONLY with units having the Perfect
Humidity adaptive dehumidification system. DO NOT use
standard charge (Fig. 51--54 and 59--62) for units with Perfect
Humidity system, and DO NOT use Fig. 55--58 for standard
units.
C06143
Fig. 55 --- Cooling Charging Chart, 581B 036 with
Optional Perfect Humidity Adaptive Dehumidification
System
48
C06145
Fig. 57 --- Cooling Charging Chart, 581B 048 with
Optional Perfect Humidity Adaptive Dehumidification
System
Step 10 —Flue Gas Passageways
To inspect the flue collector box and upper areas of the heat
exchanger:
1. Remove the combustion blower wheel and motor
assembly according to directions in Combustion-Air
Blower section below.
2. Remove the 3 screws holding the blower housing to the
flue cover.
3. Remove the flue cover to inspect the heat exchanger.
4. Clean all surfaces as required using a wire brush.
C06146
Fig. 58 --- Cooling Charging Chart, 581B 072 with
Optional Perfect Humidity Adaptive Dehumidification
System
49
581B,C
To Use Cooling Charging Chart, Standard Unit
Take the outdoor ambient temperature and read the suction
pressure gauge. Refer to charts to determine what suction
temperature should be. If suction temperature is high, add
refrigerant. If suction temperature is low, carefully recover some
of the charge. Recheck the suction pressure as charge is adjusted.
Example (Fig. 52):
Outdoor Temperature . . . . . . . . . . . . . . . . . . . . . . . . . 75°F
Suction Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 psig
Suction Temperature should be . . . . . . . . . . . . . . . . . . 48°F
(Suction temperature may vary ± 5°F.)
If a charging device is used, temperature and pressure readings
must be accomplished using the charging charts.
To Use Cooling Charging Charts, Units With Perfect
Humidityt Adaptive Dehumidification System
Refer to charts (Fig. 55--58) to determine the proper leaving
condenser pressure and temperature.
Example (Fig. 55):
Leaving Condenser Pressure . . . . . . . . . . . . . . . . . 250 psig
Leaving Condenser Temperature . . . . . . . . . . . . . . . 105°F
NOTE: When using the charging charts, it is important that only
the subcooling/reheat dehumidification coil liquid line solenoid
valve be energized. The subcooling/reheat dehumidification coil
liquid line solenoid valve MUST be energized to use the charging
charts and the outdoor motor speed controller jumpered to run the
fan at full speed.
F
125
115
105
95
85
75
581C - 2 TON CHARGING CHART
Suction Line Temperature (deg C)
5.5
10.5
15.5
20.5
25.5
C
52
46
41
35
29
24
105.0
Suction Line Pressure (psig)
648.0
90.0
598.0
85.0
80.0
548.0
75.0
498.0
70.0
65.0
448.0
42
52
62
72
Suction Line Temp (deg F)
C06148
Fig. 59 --- Cooling Charging Chart,
Standard 581C 024
F
115
105
95
85
75
581C -- 3 TON CHARGING CHART
Suction Line Temperature (deg C)
6.1
11.1
16.1
C
46
41
35
29
24
21.1
95.0
648.2
598.2
85.0
548.2
75.0
498.2
65.0
Suction Line Pressure (kpa)
Suction Line Pressure (psig)
581B,C
95.0
Suction Line Pressure (kpa)
698.0
100.0
448.2
43
48
53
58
63
68
Suction Line Temp (deg F)
Fig. 60 --- Cooling Charging Chart,
Standard 581C 036
50
73
78
C06149
F
C
115 46
105 41
95
35
85
29
75
24
581C -- 4 TON CHARGING CHART
Suction Line Temperature (deg C)
5.6
10.6
15.6
20.6
25.6
87.0
592.0
77.0
542.0
581B,C
642.0
Suction Line Pressure (kpa)
Suction Line Pressure (psig)
692.0
97.0
492.0
67.0
42
47
52
57
62
67
72
77
Suction Line Temp (deg F)
C06150
Fig. 61 --- Cooling Charging Chart,
Standard 581C 048
F
115
105
95
85
75
581C - 5 TON CHARGING CHART
Suction Line Temperature (deg C)
0.0
5.0
10.0
15.0
20.0
25.0
710.0
105.0
95.0
610.0
85.0
510.0
75.0
410.0
65.0
55.0
Suction Line Pressure (kpa)
810.0
115.0
Suction Line Pressure (psig)
C
46
41
35
29
24
310.0
42
47
52
57
62
67
72
77
Suction Line Temp (deg F)
Fig. 62 --- Cooling Charging Chart,
Standard 581C 060
51
C06151
581B,C
Step 11 —Combustion--Air Blower
Step 14 —Main Burners
Clean periodically to ensure proper airflow and heating
efficiency. Inspect blower wheel every fall and periodically
during heating season. For the first heating season, inspect blower
wheel bimonthly to determine proper cleaning frequency.
To inspect blower wheel, remove draft hood and screen. Shine a
flashlight into opening to inspect wheel. If cleaning is required,
remove motor and wheel as follows:
1. Slide burner access panel out.
2. Remove the 5 screws that attach induced-draft motor
assembly to the vestibule cover.
3. Slide the motor and blower wheel assembly out of the
blower housing. The blower wheel can be cleaned at this
point. If additional cleaning is required, continue with
Steps 4 and 5.
4. To remove blower from the motor shaft, remove
2 setscrews.
5. To remove motor, remove the 4 screws that hold the
motor to mounting plate. Remove the motor cooling fan
by removing one setscrew. Then remove nuts that hold
motor to mounting plate.
6. To reinstall, reverse the procedure outlined above.
At the beginning of each heating season, inspect for deterioration
or blockage due to corrosion or other causes. Observe the main
burner flames and adjust, if necessary.
Step 12 —Limit Switch
Remove blower access panel (Fig. 8). Limit switch is located on
the fan deck.
Step 13 —Burner Ignition
Unit is equipped with a direct spark ignition 100% lockout
system. Integrated Gas Unit Controller (IGC) is located in the
control box (Fig. 13). A single LED on the IGC provides a visual
display of operational or sequential problems when the power
supply is uninterrupted. The LED can be observed through the
viewport. When a break in power occurs, the IGC will be reset
(resulting in a loss of fault history) and the evaporator fan on/off
times delay will be reset. During servicing, refer to the label on
the control box cover or Table 39 for an explanation of LED error
code descriptions.
If lockout occurs, unit may be reset by interrupting power supply
to unit for at least 5 seconds.
!
FURNACE DAMAGE HAZARD
Failure to follow this caution may result in reduced furnace
life.
When servicing gas train, do not hit or plug orifice spuds.
Removal and Replacement of Gas Train
(See Fig. 63 and 64)
1. Shut off manual gas valve.
2. Shut off power to unit, tag disconnect.
3. Remove compressor access panel.
4. Slide out burner compartment side panel.
5. Disconnect gas piping at unit gas valve.
6. Remove wires connected to gas valve. Mark each wire.
7. Remove induced-draft motor, igniter, and sensor wires at
the Integrated Gas Unit Controller (IGC).
8. Remove the 2 screws that attach the burner rack to the
vestibule plate.
9. Remove the gas valve bracket.
10. Slide the burner tray out of the unit (Fig. 64).
11. To reinstall, reverse the procedure outlined above.
12. Reinstall burners on rack.
INDUCEDDRAFT
MOTOR
MOUNTING
PLATE
ROLLOUT
SWITCH
BURNER
SECTION
Table 38—LED Error Code Description*
LED INDICATION
ON
OFF
1 Flash†
2 Flashes
3 Flashes
4 Flashes
5 Flashes
6 Flashes
7 Flashes
8 Flashes
9 Flashes
CAUTION
ERROR CODE DESCRIPTION
FLUE
EXHAUST
VESTIBULE
PLATE
INDUCEDDRAFT
MOTOR
Normal Operation
Hardware Failure
Evaporator Fan On/Off Delay Modified
Limit Switch Fault
Flame Sense Fault
4 Consecutive Limit Switch Faults
Ignition Lockout Fault
Induced-Draft Motor Fault
Rollout Switch Fault
Internal Control Fault
Software Lockout
BLOWER
HOUSING
MANIFOLD
PRESSURE
TAP
GAS
VALVE
Fig. 63 --- Burner Section Details
C06152
LEGEND
LED — Light-Emitting Diode
*A 3-second pause exists between LED error code flashes. If more than
one error code exists, all applicable codes will be displayed in numerical sequence.
†Indicates a code that is not an error. The unit will continue to operate
when this code is displayed.
IMPORTANT: Refer to Troubleshooting Tables for additional
information.
Fig. 64 --- Burner Tray Details
52
C06153
LOW HEAT
581B,C
72,000 BTUH INPUT AND 60,000 BTUH INPUT
MEDIUM AND HIGH HEAT
115,000 BTUH INPUT,
150,000 BTUH INPUT,
90,000BTUH INPUT AND
120,000 BTUH INPUT
Fig. 65 --- Spark Gap Adjustment
Cleaning and Adjustment
1. Remove burner rack from unit as described above.
2. Inspect burners and, if dirty, remove burners from rack.
3. Using a soft brush, clean burners and cross-over port as
required.
4. Adjust spark gap. (See Fig. 65.)
C06154
5. Reinstall burner rack as described above.
Step 15 —Replacement Parts
A complete list of replacement parts may be obtained from any
Bryant distributor upon request. Refer to Fig. 66 for a typical unit
wiring schematic.
53
581B,C
NOTES:
1. If any of the original wire furnished must be replaced, it must
be replaced with type 90 C wire or its equivalent.
2. Three phase motors are protected under primary single
phasing conditions.
3. Use copper conductors only.
4. TRAN is wired for 230 v unit. If unit is to be run with 208 v
power supply, disconnect BLK wire from 230 v tap (ORN)
and connect to 208 v tap (RED). Insulate end of 230 v tap.
LEGEND
C
CAP
CLO
COMP
EQUIP
FPT
FU
GND
HPS
HS
I
IDM
IFC
IFM
IGC
LPS
LS
MGV
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Contactor, Compressor
Capacitor
Compressor Lockout
Compressor Motor
Equipment
Freeze Up Protection Thermostat
Fuse
Ground
High-Pressure Switch
Hall-Effect Sensor
Ignitor
Induced-Draft Motor
Indoor Fan Contactor
Indoor Fan Motor
Integrated Gas Unit Controller
Low-Pressure Switch
Limit Switch
Main Gas Valve
OFM
OLR
P
PL
QT
RS
SAT
TRAN
—
—
—
—
—
—
—
—
Outdoor (Condenser) Fan Motor
Overload Relay
Plug
Plug Assembly
Quadruple Terminal
Rollout Switch
Supply Air Temperature Sensor
Transformer
Splice
Splice (Marked)
Factory Wiring
Field Control Wiring
Field Splice
Field Power Wiring
Marked Wire
Accessory or Optional Wiring
To indicate common potential only;
not to represent wiring.
Terminal (Marked)
Terminal (Unmarked)
Terminal Block
Fig. 66 --- Typical Wiring Schematic and Component Arrangement (208/230--3--60 Shown)
54
C06147
Unit Troubleshooting
Refer to Tables 39--43 for unit troubleshooting details.
Economi$er IV Troubleshooting
See Table 44 for EconoMi$er IV logic.
A functional view of the EconoMi$er IV is shown in Fig. 60.
Typical settings, sensor ranges, and jumper positions are also
shown. An EconoMi$er IV simulator program is available from
your Bryant distributor to help with EconoMi$er IV training and
troubleshooting.
Economi$er IV Preparation
This procedure is used to prepare the EconoMi$er IV for
troubleshooting. No troubleshooting or testing is done by
performing the following procedure.
NOTE: This procedure requires a 9-v battery, 1.2 kilo-ohm
resistor, and a 5.6 kilo-ohm resistor which are not supplied with
the EconoMi$er IV.
IMPORTANT: Be sure to record the positions of all
potentiometers before starting troubleshooting.
1. Disconnect power at TR and TR1. All LEDs should be
off. Exhaust fan contacts should be open.
2. Disconnect device at P and P1.
3. Jumper P to P1.
4. Disconnect wires at T and T1. Place 5.6 kilo-ohm resistor
across T and T1.
5. Jumper TR to 1.
6. Jumper TR to N.
7. If connected, remove sensor from terminals SO and +.
Connect 1.2 kilo-ohm 4074EJM checkout resistor across
terminals SO and +.
8. Put 620-ohm resistor across terminals SR and +.
9. Set minimum position, DCV set point, and exhaust
potentiometers fully CCW (counterclockwise).
10. Set DCV maximum position potentiometer fully CW
(clockwise).
11. Set enthalpy potentiometer to D.
12. Apply power (24 vac) to terminals TR and TR1.
Differential Enthalpy
To check differential enthalpy:
1. Make sure EconoMi$er IV preparation procedure has been
performed.
2. Place 620-ohm resistor across SO and +.
3. Place 1.2 kilo-ohm resistor across SR and +. The Free
Cool LED should be lit.
4. Remove 620-ohm resistor across SO and +. The Free Cool
LED should turn off.
5. Return EconoMi$er IV settings and wiring to normal
after completing troubleshooting.
Single Enthalpy
To check single enthalpy:
1. Make sure EconoMi$er IV preparation procedure has been
performed.
2. Set the enthalpy potentiometer to A (fully CCW). The
Free Cool LED should be lit.
3. Set the enthalpy potentiometer to D (fully CW). The Free
Cool LED should turn off.
4. Return EconoMi$er IV settings and wiring to normal
after completing troubleshooting.
DCV (Demand Controlled Ventilation) and Power Exhaust
To check DCV and Power Exhaust:
1. Make sure EconoMi$er IV preparation procedure has been
performed.
2. Ensure terminals AQ and AQ1 are open. The LED for
both DCV and Exhaust should be off. The actuator should
be fully closed.
3. Connect a 9-v battery to AQ (positive node) and AQ1
(negative node). The LED for both DCV and Exhaust
should turn on. The actuator should drive to between 90
and 95% open.
4. Turn the Exhaust potentiometer CW until the Exhaust
LED turns off. The LED should turn off when the
potentiometer is approximately 90%. The actuator should
remain in position.
5. Turn the DCV set point potentiometer CW until the DCV
LED turns off. The DCV LED should turn off when the
potentiometer is approximately 9v. The actuator should
drive fully closed.
6. Turn the DCV and Exhaust potentiometers CCW until the
Exhaust LED turns on. The exhaust contacts will close 30
to 120 seconds after the Exhaust LED turns on.
7. Return EconoMi$er IV settings and wiring to normal
after completing troubleshooting.
DCV Minimum and Maximum Position
To check the DCV minimum and maximum position:
1. Make sure EconoMi$er IV preparation procedure has been
performed.
2. Connect a 9-v battery to AQ (positive node) and AQ1
(negative node). The DCV LED should turn on. The
actuator should drive to between 90 and 95% open.
3. Turn the DCV Maximum Position potentiometer to
midpoint. The actuator should drive to between 20 and
80% open.
4. Turn the DCV Maximum Position potentiometer to fully
CCW. The actuator should drive fully closed.
5. Turn the Minimum Position potentiometer to midpoint.
The actuator should drive to between 20 and 80% open.
6. Turn the Minimum Position Potentiometer fully CW. The
actuator should drive fully open.
7. Remove the jumper from TR and N. The actuator should
drive fully closed.
8. Return EconoMi$er IV settings and wiring to normal
after completing troubleshooting.
Supply--Air Input
To check supply-air input:
1. Make sure EconoMi$er IV preparation procedure has been
performed.
2. Set the Enthalpy potentiometer to A. The Free Cool LED
turns on. The actuator should drive to between 20 and
80% open.
3. Remove the 5.6 kilo-ohm resistor and jumper T to T1. The
actuator should drive fully open.
4. Remove the jumper across T and T1. The actuator should
drive fully closed.
5. Return EconoMi$er IV settings and wiring to normal
after completing troubleshooting.
55
581B,C
TROUBLESHOOTING
Economi$er IV Troubleshooting Completion
This procedure is used to return the EconoMi$er IV to operation.
No troubleshooting or testing is done by performing the
following procedure.
1. Disconnect power at TR and TR1.
2. Set enthalpy potentiometer to previous setting.
3. Set DCV maximum position potentiometer to previous
setting.
4. Set minimum position, DCV set point, and exhaust
potentiometers to previous settings.
5. Remove 620-ohm resistor from terminals SR and +.
6. Remove 1.2 kilo-ohm checkout resistor from terminals SO
and +. If used, reconnect sensor from terminals SO and +.
7. Remove jumper from TR to N.
8. Remove jumper from TR to 1.
9. Remove 5.6 kilo-ohm resistor from T and T1. Reconnect
wires at T and T1.
10. Remove jumper from P to P1. Reconnect device at P and
P1.
11. Apply power (24 vac) to terminals TR and TR1.
Table 39—LED Error Code Service Analysis
581B,C
SYMPTOM
Hardware Failure.
(LED OFF)
CAUSE
Loss of power to control module (IGC).
Fan ON/OFF Delay Modified High limit switch opens during heat
exchanger warm-up period before fan-on
(LED/FLASH)
delay expires.
Limit switch opens within three minutes
after blower-off delay timing in Heating
mode.
Limit Switch Fault.
High temperature limit switch is open.
(LED 2 Flashes)
Flame Sense Fault.
(LED 3 Flashes)
4 Consecutive Limit
Switch Faults.
(LED 4 Flashes)
Ignition Lockout.
(LED 5 Flashes)
The IGC sensed flame that should not be
present.
Inadequate airflow to unit.
Induced-Draft Motor Fault.
(LED 6 Flashes)
IGC does not sense that induced-draft
motor is operating.
Rollout Switch Fault.
(LED 7 Flashes)
Rollout switch has opened.
Internal Control Fault.
(LED 8 Flashes)
Temporary Software
Lockout
(LED 9 Flashes)
Microprocessor has sensed an error in the
software or hardware.
Electrical interference is impeding the IGC
software.
!
Unit unsuccessfully attempted ignition for
15 minutes.
CAUTION
REMEDY
Check 5 amp fuse on IGC, power to unit, 24-v circuit breaker, and
transformer. Units without a 24-v circuit breaker have an internal
overload in the 24-v transformer. If the overload trips, allow
10 minutes for automatic reset.
Ensure unit is fired on rate and temperature rise is correct.
Ensure units’ external static pressure is within application guidelines.
Check the operation of the indoor (evaporator) fan motor.
Ensure that the supply-air temperature rise is in accordance with
the range on the unit nameplate.
Reset unit. If problem persists, replace control board.
Check operation of indoor (evaporator) fan motor and that supply-air
temperature rise agrees with range on unit nameplate information.
Check ignitor and flame sensor electrode spacing, gaps, etc.
Ensure that flame sense and ignition wires are properly
terminated. Verify that unit is obtaining proper amount of gas.
Check for proper voltage. If motor is operating, check the
speed sensor plug/IGC Terminal J2 connection. Proper
connection: PIN 1— White, PIN 2 — Red, PIN 3 — Black.
Rollout switch will automatically reset, but IGC will continue to
lock out unit. Check gas valve operation. Ensure that induceddraft blower wheel is properly secured to motor shaft.
Reset unit at unit disconnect.
If error code is not cleared by resetting unit power, replace the IGC.
Reset 24-v to control board or turn thermostat off and then on. Fault
will automatically reset itself in one hour.
IMPORTANT: Refer to heating troubleshooting for additional
heating section troubleshooting information.
COMPONENT DAMAGE HAZARD
Failure to follow this caution may result in component
damage.
If the IGC must be replaced, be sure to ground yourself to
dissipate any electrical charge that may be present before
handling new control board. The IGC is sensitive to static
electricity and may be damaged if the necessary precautions
are not taken.
LEGEND
IGC --- Integrated Gas Unit Controller
LED --- Light---Emitting Diode
56
Table 40— Heating Service Analysis
CAUSE
REMEDY
Misaligned spark electrodes.
No gas at main burners.
Water in gas line.
No power to furnace.
No 24 v power supply to control circuit.
Miswired or loose connections.
Burned-out heat anticipator in thermostat.
Broken thermostat wires.
Dirty air filter.
Gas input to unit too low.
Inadequate Heating.
Unit undersized for application.
Restricted airflow.
Blower speed too low.
Limit switch cycles main burners.
Too much outdoor air.
Poor Flame
Characteristics.
Incomplete combustion (lack of
combustion air) results in:
Aldehyde odors, CO (carbon monoxide),
sooting
ti flame,
fl
or flfloating
ti flflame.
Burners Will Not
Turn Off.
Unit is locked into Heating mode for a
one minute minimum.
Check flame ignition and sensor electrode positioning. Adjust as needed.
Check gas line for air purge as necessary. After purging gas line of air, allow gas
to dissipate for at least 5 minutes before attempting to relight unit.
Check gas valve.
Drain water and install drip leg to trap water.
Check power supply, fuses, wiring, and circuit breaker.
Check transformer. Transformers with internal overcurrent protection require a
cool-down period before resetting. Check 24-v circuit breaker; reset if necessary.
Check all wiring and wirenut connections.
Replace thermostat.
Run continuity check. Replace wires, if necessary.
Clean or replace filter as necessary.
Check gas pressure at manifold. Clock gas meter for input. If too low, increase
manifold pressure or replace with correct orifices.
Replace with proper unit or add additional unit.
Clean filter, replace filter, or remove any restrictions.
Use high speed tap, increase fan speed, or install optional blower, as suitable
for individual units, Adjust pulley.
Check rotation of blower, thermostat heat anticipator settings, and temperature
rise of unit. Adjust as needed.
Adjust minimum position.
Check economizer operation.
Check all screws around flue outlets and burner compartment. Tighten as necessary.
Cracked heat exchanger.
Overfired unit — reduce input, change orifices, or adjust gas line or manifold
pressure.
Check vent for restriction. Clean as necessary.
Check orifice to burner alignment.
Wait until mandatory one-minute time period has elapsed or reset power to
unit.
Table 41—Perfect Humidity™ Adaptive Dehumidification System Subcooling Mode Service Analysis
PROBLEM
Subcooling Mode (Liquid Reheat)
Will Not Energize.
CAUSE
No power to control transformer from
evaporator-fan motor.
No power from control transformer to liquid line
solenoid valve.
Liquid line solenoid valve will not operate.
Low System Capacity.
Loss of Compressor Superheat
Conditions with Subcooling/Reheat
Dehumidification Coil Energized.
Liquid line solenoid valve will not open.
Low refrigerant charge or frosted evaporator coil.
Thermostatic expansion valve (TXV).
REMEDY
Check power source and evaporator-fan relay. Ensure all
wire connections are tight.
1. Fuse open; check fuse. Ensure continuity of wiring.
2. Low-pressure switch open. Cycle unit off and allow
low-pressure switch to reset. Replace switch if it will
not close.
3. Transformer bad; check transformer.
1. Solenoid coil defective; replace.
2. Solenoid valve stuck open; replace.
Valve is stuck closed; replace valve.
1. Check charge amount. Charge per Fig. 55--- 58.
2. Evaporator coil frosted; check and replace low-pressure switch if necessary.
1. Check TXV bulb mounting, and secure tightly to suction line.
2. Replace TXV if stuck open or closed.
Table 42—Perfect Humidity™ Adaptive Dehumidification System Hot Gas Reheat Mode Service Analysis
PROBLEM
Reheat Mode Will Not Energize.
CAUSE
No power to control transformer from
evaporator-fan motor.
No power from control transformer to hot gas
line solenoid valve
Hot gas line solenoid valve will not operate.
Low refrigerant charge or frosted evaporator coil.
Loss of Compressor Superheat
Conditions with Subcooling/Reheat
Dehumidification Coil Energized.
Excessive Superheat.
Thermostatic expansion valve (TXV).
Liquid line solenoid valve will not operate.
Hot gas line solenoid valve will not close.
57
REMEDY
Check power source and evaporator-fan relay. Ensure all
wire connections are tight.
1. Fuse open; check fuse. Ensure continuity of wiring.
2. Low-pressure switch open. Cycle unit off and allow
low-pressure switch to reset. Replace switch if it will
not close.
3. Transformer bad; check transformer.
1. Solenoid coil defective; replace.
2. Solenoid valve stuck closed; replace.
1. Check charge amount. Charge per Fig. 55--- 58.
2. Evaporator coil frosted; check and replace low-pressure switch if necessary.
1. Check TXV bulb mounting, and secure tightly to suction line.
2. Replace TXV if stuck open or closed.
Valve is stuck, replace valve.
Valve is stuck; replace valve.
581B,C
PROBLEM
Burners Will Not
Ig it
Ignite.
Table 43—Cooling Service Analysis
PROBLEM
Compressor and Condenser Fan
Will N
Not S
Start.
581B,C
Compressor Will Not Start
But Condenser Fan Runs.
Compressor Cycles (Other Than
Normally Satisfying Thermostat).
Compressor Operates Continuously.
Excessive Head Pressure.
Head Pressure Too Low.
Excessive Suction Pressure.
Suction Pressure Too Low.
Evaporator Fan Will Not Shut Off.
CAUSE
Power failure.
Fuse blown or circuit breaker tripped.
Defective thermostat, contactor, transformer, or
control relay.
Insufficient line voltage.
Incorrect or faulty wiring.
Thermostat setting too high.
Faulty wiring or loose connections in compressor circuit.
Compressor motor burned out, seized, or internal overload open.
Defective run/start capacitor, overload, start
relay.
One leg of 3-phase power dead.
Refrigerant overcharge or undercharge.
Defective compressor.
Insufficient line voltage.
Blocked condenser.
Defective run/start capacitor, overload, or start
relay.
Defective thermostat.
Faulty condenser-fan motor or capacitor.
Restriction in refrigerant system.
Dirty air filter.
Unit undersized for load.
Thermostat set too low.
Low refrigerant charge.
Leaking valves in compressor.
Air in system.
Condenser coil dirty or restricted.
Dirty air filter.
Dirty condenser coil.
Refrigerant overcharged.
Air in system.
Condenser air restricted or air short-cycling.
Low refrigerant charge.
Compressor valves leaking.
Restriction in liquid tube.
High heat load.
Compressor valves leaking.
Refrigerant overcharged.
Dirty air filter.
Low refrigerant charge.
Metering device or low side restricted.
Insufficient evaporator airflow.
Temperature too low in conditioned area.
Outdoor ambient below 25 F.
Time off delay not finished.
58
REMEDY
Call power company.
Replace fuse or reset circuit breaker.
Replace component.
Determine cause and correct.
Check wiring diagram and rewire correctly.
Lower thermostat setting below room temperature.
Check wiring and repair or replace.
Determine cause. Replace compressor.
Determine cause and replace.
Replace fuse or reset circuit breaker. Determine
cause.
Recover refrigerant, evacuate system, and recharge to nameplate.
Replace and determine cause.
Determine cause and correct.
Determine cause and correct.
Determine cause and replace.
Replace thermostat.
Replace.
Locate restriction and remove.
Replace filter.
Decrease load or increase unit size.
Reset thermostat.
Locate leak, repair, and recharge.
Replace compressor.
Recover refrigerant, evacuate system, and recharge.
Clean coil or remove restriction.
Replace filter.
Clean coil.
Recover excess refrigerant.
Recover refrigerant, evacuate system, and recharge.
Determine cause and correct.
Check for leaks, repair, and recharge.
Replace compressor.
Remove restriction.
Check for source and eliminate.
Replace compressor.
Recover excess refrigerant.
Replace filter.
Check for leaks, repair, and recharge.
Remove source of restriction.
Increase air quantity. Check filter and replace if
necessary.
Reset thermostat.
Install low-ambient kit.
Wait for 30-second off delay.
Table 44—EconoMi$er IV Input/Output Logic
V til ti (DCV)
Ventilation
Below set
(DCV LED Off)
Above set
(DCV LED On)
O )
Outdoor
Return
High
(F
(Free
Cooling
C li LED Off)
Low
Low
(F
(Free
Cooling
C li LED On)
O )
High
High
(F
(Free
Cooling
C li LED Off)
Low
Low
(F
(Free
Cooling
C li LED On)
O )
High
Y1
On
On
Off
On
On
Off
On
On
Off
On
On
Off
Y2
On
Off
Off
On
Off
Off
On
Off
Off
On
Off
Off
OUTPUTS
N Terminal†
Compressor
Stage Stage
1
On
On
Off
On
Off
Off
On
On
Off
On
Off
Off
2
On
Off
Off
Off
Off
Off
On
Off
Off
Off
Off
Off
Occupied
Unoccupied
Damper
Minimum position
Closed
Modulating (between min.
Modulating**
position
i i and
d ffull-open)
ll
)
Modulating (between
Modulating**
closed
l
d and
d ffull-open)
ll
)
Minimum position
Modulating†† (between min.
position
i i and
d DCV maximum)
i
)
Closed
Modulating†† (between
closed
l
d and
d DCV
maximum)
Modulating***
Modulating
Modulating†††
*For single enthalpy control, the module compares outdoor enthalpy to the ABCD set point.
†Power at N terminal determines Occupied/Unoccupied setting: 24 vac (Occupied), no power (Unoccupied).
**Modulation is based on the supply-air sensor signal.
††Modulation is based on the DCV signal.
***Modulation is based on the greater of DCV and supply-air sensor signals, between minimum position and either maximum position (DCV) or fully open (supply-air signal).
†††Modulation is based on the greater of DCV and supply-air sensor signals, between closed and either maximum position (DCV) or fully open (supply-air signal).
Fig. 67 --- EconoMi$er IV Functional View
59
C06053
581B,C
Demand Control
INPUTS
Enthalpy*
START-UP CHECKLIST
(Remove and Store in Job File)
I. PRELIMINARY INFORMATION
MODEL NO.:
SERIAL NO.:
DATE:
TECHNICIAN:
II. PRE-START-UP (insert checkmark in box as each item is completed)
j VERIFY THAT JOBSITE VOLTAGE AGREES WITH VOLTAGE LISTED ON RATING PLATE
j VERIFY THAT ALL PACKAGING MATERIALS HAVE BEEN REMOVED FROM UNIT
j REMOVE ALL SHIPPING HOLDDOWN BOLTS AND BRACKETS PER INSTALLATION INSTRUCTIONS
j VERIFY THAT CONDENSATE CONNECTION IS INSTALLED PER INSTALLATION INSTRUCTIONS
581B,C
j CHECK ALL ELECTRICAL CONNECTIONS AND TERMINALS FOR TIGHTNESS
j CHECK GAS PIPING FOR LEAKS
j CHECK THAT RETURN (INDOOR) AIR FILTERS ARE CLEAN AND IN PLACE
j VERIFY THAT UNIT INSTALLATION IS LEVEL
j CHECK FAN WHEELS AND PROPELLER FOR LOCATION IN HOUSING/ORIFICE AND SETSCREW
TIGHTNESS
j CHECK TO ENSURE THAT ELECTRICAL WIRING IS NOT IN CONTACT WITH REFRIGERANT LINES
OR SHARP METAL EDGES
j CHECK PULLEY ALIGNMENT AND BELT TENSION PER INSTALLATION INSTRUCTIONS
III. START-UP
ELECTRICAL
SUPPLY VOLTAGE
COMPRESSOR AMPS
INDOOR-FAN AMPS
L1-L2
L1
L1
L3-L1
L3
L3
L2-L3
L2
L2
TEMPERATURES
OUTDOOR-AIR TEMPERATURE
DB
RETURN-AIR TEMPERATURE
DB
COOLING SUPPLY AIR
DB
HEATING SUPPLY AIR
DB
WB
PRESSURES (Cooling Mode)
GAS INLET PRESSURE
IN.WG
GAS MANIFOLD PRESSURE
IN.WG (HIGH FIRE)
REFRIGERANT SUCTION
PSIG
REFRIGERANT DISCHARGE
PSIG
j VERIFY THAT 3-PHASE FAN MOTOR AND BLOWER ARE ROTATING IN CORRECT DIRECTION. IF THEY
ARE NOT ROTATING IN CORRECT DIRECTION, LOCKING COLLAR MUST BE RE--TIGHTENED AFTER
CORRECTING DIRECTION OF ROTATION
j VERIFY THAT 3-PHASE SCROLL COMPRESSOR IS ROTATING IN THE CORRECT DIRECTION
j VERIFY REFRIGERANT CHARGE USING CHARGING CHARTS
E2007 Bryant Heating & Cooling Systems 7310 W. Morris St. Indianapolis, IN 46231
Printed in U.S.A.
Edition Date: 2/07
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
60
Catalog No. II581B---C ---36---1
Replaces: II 581B--- 36--- 7
Download PDF

advertising