Bryant 698B Heat Pump User Manual

installation and
start-up instructions
698B
TWO-SPEED PURON® PLUS HEAT PUMP
WITH PURON® REFRIGERANT
Cancels:
II 698B-24-3
II 698B-24-4
2-03
NOTE: Read the entire instruction manual before starting the
installation.
SAFETY CONSIDERATIONS
Improper installation, adjustment, alteration, service, maintenance,
or use can cause explosion, fire, electrical shock, or other
conditions which may cause death, personal injury, or property
damage. Consult a qualified installer, service agency, or your
distributor or branch for information or assistance. The qualified
installer or agency must use factory-authorized kits or accessories
when modifying this product. Refer to the individual instructions
packaged with the kits or accessories when installing.
Follow all safety codes. Wear safety glasses, protective clothing,
and work gloves. Use quenching cloth for brazing operations.
Have fire extinguisher available. Read these instructions thoroughly and follow all warnings or cautions included in literature
and attached to the unit. Consult local building codes and National
Electrical Code (NEC) for special requirements.
.
Recognize safety information. This is the safety-alert symbol
When you see this symbol on the unit and in instructions or
manuals, be alert to the potential for personal injury.
Understand the signal words DANGER, WARNING, and CAUTION. These words are used with the safety-alert symbol. DANGER identifies the most serious hazards which will result in severe
personal injury or death.
WARNING signifies hazards which could result in personal injury
or death. CAUTION is used to identify unsafe practices which
would result in minor personal injury or product and property
damage. NOTE is used to highlight suggestions which will result
in enhanced installation, reliability, or operation.
•
TW
O- S P
E
E
D
•
™
A01050
Fig. 1—Model 698B
4. Leave some slack between structure and unit to absorb
vibration.
5. When passing refrigerant tubes through the wall, seal
opening with RTV or other pliable silicon-based caulk. (See
Fig. 2.)
6. Avoid direct tubing contact with water pipes, duct work,
floor joists, wall studs, floors, and walls.
7. Do not suspend refrigerant tubing from joists and studs with
a rigid wire or strap which comes in direct contact with
tubing. (See Fig. 2.)
WARNING: Before installing, modifying, or servicing
system, main electrical disconnect switch must be in the
OFF position. There may be more than 1 disconnect
switch. Lock out and tag switch with a suitable warning
label. Electrical shock can cause personal injury or death.
8. Ensure that tubing insulation is pliable and completely
surrounds vapor tube.
9. When necessary, use hanger straps which are 1 in. wide and
conform to shape of tubing insulation. (See Fig. 2.)
10. Isolate hanger straps from insulation by using metal sleeves
bent to conform to shape of insulation.
When outdoor unit is connected to factory-approved indoor unit,
outdoor unit contains system refrigerant charge for operation with
indoor unit of the same size when connected by 15 ft of
field-supplied or factory accessory tubing. For proper unit operation, check refrigerant charge using charging information located
on control box cover or in the Check Charge section of this
instruction.
IMPORTANT: Maximum liquid-line size is 3/8–in O.D. for all
residential applications.
IMPORTANT: Always install the factory-supplied Puron® heat
pump (bi-flow) liquid line filter drier. Obtain replacement filter
driers from your distributor or branch.
CAUTION: Puron® (R-410A) systems operate at higher
pressures than standard R-22 systems. Be certain that
service equipment is rated for R-410A. Some R-22
service equipment may not be acceptable. Check with
your distributor.
INSTALLATION RECOMMENDATIONS
NOTE: In some cases noise in the living area has been traced to
gas pulsations from improper installation of equipment.
1. Locate unit away from windows, patios, decks, etc. where
unit operation sound may disturb customer.
2. Ensure that vapor and liquid tube diameters are appropriate
to capacity of unit.
3. Run refrigerant tubes as directly as possible by avoiding
unnecessary turns and bends.
—1—
NOTE: Avoid contact between tubing and structure
OUTDOOR WALL
INDOOR WALL
CAULK
LIQUID TUBE
CL
A
VAPOR TUBE
INSULATION
B
THROUGH THE WALL
JOIST
HANGER STRAP
(AROUND VAPOR
TUBE ONLY)
INSULATION
VAPOR TUBE
3⁄8 IN.
DIA TIEDOWN
KNOCKOUTS
(2) PLACES
IN BASEPAN
8 3⁄16″
A97375
1″ MIN.
LIQUID TUBE
SUSPENSION
MINIMUM
TIEDOWN KNOCKOUT
MOUNTING PAD
LOCATIONS
UNIT SIZE
DIMENSIONS
Support Feet Snow Stand
A
B
024
19 X 24
26 X 32
2-13/16
6-15/16
036-060
26 X 32
31 X 35
4
9-3/4
A01383
Fig. 2—Connecting Tubing Installation
INSTALLATION
I.
Fig. 3—Mounting Unit to Pad
CHECK EQUIPMENT AND JOB SITE
A. UNPACK UNIT
Move to final location. Remove carton, taking care not to damage
unit.
B. INSPECT EQUIPMENT
File claim with shipping company prior to installation if shipment
is damaged or incomplete. Locate unit rating plate on unit corner
panel. It contains information needed to properly install unit.
II. INSTALL ON A SOLID, LEVEL MOUNTING PAD
If conditions or local codes require the unit be attached to pad, tie
down bolts should be used and fastened through knockouts
provided in unit base pan. Refer to unit mounting pattern in Fig. 3
to determine base pan size and knockout hole location.
On rooftop applications, mount on level platform or frame. Place
unit above a load-bearing wall and isolate unit and tubing set from
structure. Arrange supporting members to adequately support unit
and minimize transmission of vibration to building. Consult local
codes governing rooftop applications.
A98532
CAUTION: Do not allow POE lubricant to come into
contact with roofing material. POE may deteriorate certain types of synthetic roofing.
Fig. 4—Accessory Support Feet
IV.
Roof mounted units exposed to winds above 5 mph may require
wind baffles. Consult the Application Guideline and Service
Manual for Residential Split System Air Conditioners and Heat
Pumps using Puron® Refrigerant for wind baffle construction
NOTE: Unit must be level to within ±2° (±3/8 in./ft) per
compressor manufacturer specifications.
III.
OPERATING AMBIENT
The minimum outdoor operating ambient in cooling mode is 55°F,
and the maximum outdoor operating ambient in cooling mode is
125°F.
V.
ELEVATE UNIT
CAUTION: Accumulation of water and ice in base pan
may cause equipment damage.
CLEARANCE REQUIREMENTS
When installing, allow sufficient space for airflow clearance,
wiring, refrigerant piping, and service. Allow 30-in. clearance to
service end of unit and 48 in. above unit. For proper airflow, a 6-in.
clearance on 1 side of unit and 12 in. on all remaining sides must
be maintained. Maintain a distance of 24 in. between units.
Position so water, snow, or ice from roof or eaves cannot fall
directly on unit.
On rooftop applications, locate unit at least 6 in. above roof
surface.
Elevate unit per local climate and code requirements to provide
clearance above estimated snowfall level and ensure adequate
drainage of the unit. Fig. 4 shows unit with accessory support feet
installed. Use accessory snow stand in areas where prolonged
freezing temperatures are encountered. Refer to separate Installation Instructions packaged with accessories.
—2—
8. Install vapor elbow (See Fig. 6B) with equalizer adapter to
suction tube of line set and suction connection to indoor
coil. Adapter has a 1/4-in. male flare connector for attaching
equalizer tube.
COIL
9. Connect equalizer tube of TXV to 1/4-in. equalizer fitting
on vapor line adapter.
SENSING
BULB
10. Attach TXV bulb to horizontal section of suction line using
bulb strap provided. (See Fig. 6C.) Insulate bulb with
factory-supplied insulation tape. (See Fig. 6E.) See Fig. 7
for correct positioning of sensing bulb.
EQUALIZER
TUBE
11. Proceed with remainder of unit installation.
THERMOSTATIC
EXPANSION
VALVE
B. FAN COILS
Indoor unit (fan coil) comes factory equipped with a bi-flow
shut-off TXV specifically designed for Puron® two-speed. No
TXV changeout is required.
A91277
VI.
Fig. 5—TXV Installed
CHECK INDOOR EXPANSION DEVICE
PROCEDURE 2—REPLACING R-22 TXV OR
NON-BALANCE PORT PURON® TXV
1. Remove any existing refrigerant and ensure coil has not
been exposed to atmospheric pressure for more than 15
minutes.
CAUTION: For proper unit operation and reliability,
units must be installed with balance port hard shutoff
TXV specifically designed to operate with Puron® twospeed unit. Do not install with evaporator coils having
capillary tube metering devices.
2. Remove coil access panel and fitting door from cabinet.
3. Remove and save TXV support clamp using a 5/16-in nut
driver.
4. Remove TXV using a backup wrench on flare connections
to prevent damage to tubing.
A. FURNACE COILS
Puron® furnace coils come factory equipped with bi-flow, hard
shutoff TXV s specifically designed for Puron® two-speed units.
No changeout is required.
Remove existing Check-Flo-Rater™ piston from indoor coil and
install field accessory TXV.
Install TXV kit to indoor coil as follows:
IMPORTANT: The TXV should be mounted as close to the
indoor coil as possible and in a vertical, upright position. Avoid
mounting the inlet tube vertically down. Valve is more susceptible
to malfunction due to debris if inlet tube is facing down. A
factory-approved filter drier must be installed in the liquid line.
5. Using wire cutters, cut equalizer tube off flush with vapor
tube inside cabinet.
6. Remove bulb from vapor tube inside cabinet.
7. Braze equalizer stub-tube closed. Use protective barrier as
necessary to prevent damage to drain pan.
IMPORTANT: Route the equalizer tube of approved Puron®
TXV through suction line connection opening in fitting panel prior
to replacing fitting panel around tubing.
8. Install TXV (Fig. 6A) with 3/8-in. copper inlet tube through
small hole in service panel. Use wrench and backup wrench,
to avoid damage to tubing valve.
PROCEDURE 1—INSTALLING TXV IN PLACE OF PISTON
1. Ensure coil has not been exposed to atmospheric pressure
for more than 15 minutes.
2. Remove indoor coil inlet tube at piston body inlet. Use
back-up wrench to prevent damage.
3. Remove piston retainer, being careful not to damage sealing
surface of O-ring.
4. Remove and discard factory-installed piston. Replace retainer if O-ring is damaged.
NOTE: If the piston is not removed from the body, TXV will not
function properly.
5. Reinstall piston retainer in piston body.
6. Replace indoor coil inlet tube. Use back-up wrench to
prevent damage.
9. Reinstall TXV support clamp (removed in item 3).
10. Attach TXV bulb to vapor tube inside cabinet in same
location as original was removed using supplied bulb straps.
(See Fig. 6C.) Insulate bulb with factory-supplied insulation
tape. (See Fig. 6E.) See Fig. 7 for correct positioning of
sensing bulb.
11. Route equalizer tube through suction connection opening
(large hole) in fitting panel and install fitting panel in place.
12. Sweat inlet of TXV, marked “IN,” to liquid line. Avoid
excessive heat which could damage valve.
13. Install vapor elbow (See Fig. 6B) with equalizer adapter to
vapor line of line set and vapor connection to indoor coil.
Adapter has a 1/4-in. male flare connector for attaching
equalizer tube. (See Fig. 6B.)
14. Connect equalizer tube of TXV to 1/4-in. equalizer fitting
on vapor line adapter. Use backup wrench to prevent
damage to equalizer fitting.
CAUTION: To prevent damage to the unit, use a brazing
shield and wrap TXV with wet cloth or use heat sink
material.
15. Proceed with remainder of unit installation.
C. Long-Line Applications, Install Liquid-Line Solenoid
Valve (LSV)
For refrigerant piping arrangements with equivalent lengths
greater than 50 ft or when elevation difference between indoor
and/or outdoor unit is greater than ± 20 ft, follow all requirements
7. Sweat swivel adapter (See Fig. 6D) to inlet of indoor coil
and attach to TXV (See Fig. 6A) outlet. Use backup wrench
to avoid damage to tubing or valve. Sweat inlet of TXV,
marked “IN,” to liquid line. Avoid excessive heat which
could damage valve.
—3—
B
INLET
A
D
COIL
E
BULB
INSULATION
TAPE
C
A01418
Fig. 6—TXV Kit Contents
TABLE 1—REFRIGERANT CONNECTIONS AND
RECOMMENDED LIQUID AND VAPOR TUBE
DIAMETERS (IN.)
of the Long-Line Guideline section in the Application Guideline
and Service Manual for Residential Split-System Air Conditioners
and Heat Pumps Using Puron® Refrigerant. If required by
Long-Line Application Guideline, install LSV kit Part No.
KHALS0401LLS specifically designed for Puron® Heat Pumps.
LSV should be installed between filter drier and indoor coil as
close as possible to filter drier. Follow the Installation Instructions
included with accessory kit.
UNIT
SIZE
024
036
048
060
IMPORTANT: Flow arrow must point toward outdoor unit.
VII.
LIQUID
VAPOR
VAPOR (LONG-LINE)
Connection Tube Connection Tube
Connection
Tube
Diameter Diameter Diameter Diameter Diameter Diameter
3/8
3/8
5/8
5/8
5/8
3/4
3/8
3/8
3/4
3/4
3/4
7/8
3/8
3/8
7/8
7/8
7/8
7/8
3/8
3/8
7/8
1-1/8
7/8
1-1/8
Notes:
1. Tube diameters are for lengths up to 50 equivalent ft and/or 20 ft vertical
differential.
2. Do not increase or decrease tubing sizes.
3. If required by local codes, Pressure Guard™ kit is available. See Product
Data Sheet for part numbers.
MAKE PIPING CONNECTIONS
WARNING: Relieve pressure and recover all refrigerant
before system repair or final unit disposal to avoid
personal injury or death. Use all service ports and open all
flow-control devices, including solenoid valves.
moisture in the system. Do not leave system open to atmosphere
any longer than minimum required for installation. POE oil in
compressor is extremely susceptible to moisture absorption. Always keep ends of tubing sealed during installation.
CAUTION: Do not leave system open to atmosphere
any longer than minimum required for installation. POE
oil in compressor is extremely susceptible to moisture
absorption. Always keep ends of tubing sealed during
installation.
A. OUTDOOR UNIT CONNECTED TO FACTORYAPPROVED INDOOR UNIT
These outdoor units are carefully evaluated and listed with specific
indoor coils for proper system performance.
IMPORTANT: Do not apply indoor coils which are not factory
approved to these units.
IMPORTANT: For 036 size units matched with the FV/FK005 or
FV/FK006 and the 698BNX048 matched with the FV/FK006, a
piston change is required. Refer to the KHAPX0201BPA Installation Instructions for details.
CAUTION: To prevent compressor damage DO NOT
bury more than 36 in. of refrigerant tubing. If ANY
tubing is buried, provide 6-in. vertical rise at service
valve.
B.
INSTALL ADAPTER TUBE
1. Remove plastic retainer holding outdoor piston in liquid
service valve.
Outdoor units may be connected to indoor section using accessory
tubing package or field-supplied refrigerant grade tubing of correct
size and condition. Tubing diameters listed in Table 1 are adequate
for equivalent lengths up to 50 ft For tubing requirements beyond
50 ft, substantial capacity and performance losses can occur.
Follow the recommendations in the Application Guideline and
Service Manual for Residential Split-System Air Conditioners and
Heat Pumps Using Puron® Refrigerant to minimize losses. Refer
to Table 1 for field tubing diameters. Refer to Table 2 for
accessory requirements.
2. Check to be sure outdoor piston is properly installed in
liquid service valve.
3. Locate plastic bag taped to unit containing adapter tube.
4. Remove Teflon washer from bag and install on open end of
liquid service valve. (See Fig. 8.)
5. Remove adapter tube from bag and connect threaded nut to
liquid service valve. Tighten nut finger tight and then with
wrench an additional 1/2 turn (15 ft-lb). DO NOT OVER
TIGHTEN!
If refrigerant tubes or indoor coil are exposed to atmosphere, they
must be evacuated to 500 microns to eliminate contamination and
—4—
TABLE 2—ACCESSORY USAGE
ACCESSORY
Coastal Filter
Support Feet
Puron® Hard Shutoff TXV
Puron® Liquid-Line Solenoid Valve for Heating
REQUIRED FOR SEA-COAST
APPLICATIONS*
(WITHIN 2 MILES)
Yes
Recommended
Yes†
No
REQUIRED FOR LONG-LINE
APPLICATIONS*
(OVER 50 FT)
No
No
Yes†
LHALS0401LLS
* For tubing line sets between 50 and 175 ft, or more than 20 ft vertical differential refer to Application Guideline and Service Manual for Residential Split-System Air
Conditioners and Heat Pumps using Puron® Refrigerant.
† Required for all applications.
C.
REFRIGERANT TUBING AND FILTER DRIER
CAUTION: Installation of filter drier in liquid line is
required.
TABLE 3—REQUIRED LIQUID-LINE TEMPERATURE (°F)
LIQUID PRESSURE AT
SERVICE VALVE
(PSIG)
174
181
188
195
202
209
216
223
230
237
244
251
258
265
272
279
286
293
300
307
314
321
328
335
342
349
356
363
370
377
384
391
398
405
412
419
426
433
440
447
454
461
468
475
482
489
496
503
510
517
524
531
538
545
552
559
566
573
580
587
594
601
608
Connect vapor tubing to fittings on outdoor unit vapor service
valve. Connect liquid tubing to filter drier. (See Table 1 and Fig.
9.) Use refrigerant grade tubing. Connect other end of filter drier
to adapter tube on liquid service valve.
D. SWEAT CONNECTION
REQUIRED SUBCOOLING TEMPERATURE
(°F)
5
10
15
20
56
51
46
41
58
53
48
43
61
56
51
46
63
58
53
48
65
60
55
50
67
62
57
52
69
64
59
54
71
66
61
56
73
68
63
58
75
70
65
60
77
72
67
62
79
74
69
64
81
76
71
66
82
77
72
67
84
79
74
69
86
81
76
71
88
86
78
73
89
84
79
74
91
86
81
76
93
88
83
78
94
89
84
79
96
91
86
81
97
92
87
82
99
94
89
84
100
95
90
85
102
97
92
87
103
98
93
88
105
100
95
90
106
101
96
91
107
102
97
92
109
104
99
94
110
105
100
95
112
107
102
97
113
108
103
98
114
109
104
99
115
110
105
100
117
112
107
102
118
113
108
103
119
114
109
104
120
115
110
105
122
117
112
107
123
118
113
108
124
119
114
109
125
120
115
110
126
121
116
111
127
122
117
112
129
124
119
114
130
125
120
115
131
126
121
116
132
127
122
117
133
128
123
118
134
129
124
119
135
130
125
120
136
131
126
121
137
132
127
122
138
133
128
123
139
134
129
124
140
135
130
125
141
136
131
126
142
137
132
127
143
138
133
128
144
139
134
129
145
140
135
130
CAUTION: To avoid valve damage while brazing, service valves must be wrapped in a heat-sinking material
such as a wet cloth.
Wrap service valves and filter drier with a wet cloth or heatsinking material. Braze connections using either silver bearing or
non-silver bearing brazing material. Do not use soft solder
(materials which melt below 800°F). Consult local code requirements.
CAUTION: To prevent damage to unit or service valves,
observe the following:
• Use a brazing shield.
• Wrap service valves with wet cloth or use a heat sink
material.
E. LEAK CHECKING
Leak test all joints in indoor, outdoor, and refrigerant tubing.
F. EVACUATE REFRIGERANT TUBING AND
INDOOR COIL
CAUTION: To avoid compressor damage never use the
system compressor as a vacuum pump.
Refrigerant tubes and indoor coil must be evacuated using the
recommended deep vacuum method of 500 microns. The alternate
triple evacuation method may be used if the procedure outlined
below is followed.
IMPORTANT: Never open system under vacuum to atmosphere
without first breaking it open with nitrogen.
SENSING BULB
STRAP
SUCTION
TUBE
8 O'CLOCK
4 O'CLOCK
A02000
Fig. 7—Positioning of Sensing Bulb
—5—
SWEAT/ FLARE
ADAPTER
MICRONS
TEFLON
SEAL
PISTON
5000
4500
4000
3500
3000
2500
2000
1500
1000
500
LEAK IN
SYSTEM
VACUUM TIGHT
TOO WET
TIGHT
DRY SYSTEM
PISTON BODY
0
1
2
3
4
MINUTES
5
6
7
A95424
A95424
LIQUID SERVICE VALVE
Fig. 10—Deep Vacuum Graph
EVACUATE
A97556
BREAK VACUUM WITH DRY NITROGEN
Fig. 8—Liquid Service Valve with Sweat Adapter Tube
DEEP VACUUM METHOD
The deep vacuum method requires a vacuum pump capable of
pulling a vacuum of 500 microns and a vacuum gage capable of
accurately measuring this vacuum depth. The deep vacuum
method is the most positive way of assuring a system is free of air
and liquid water. (See Fig. 10.)
WAIT
EVACUATE
BREAK VACUUM WITH DRY NITROGEN
TRIPLE EVACUATION METHOD
The triple evacuation method should only be used when vacuum
pump is only capable of pumping down to 28 in. of mercury and
system does not contain any liquid water. Refer to Fig. 11 and
proceed as follows:
WAIT
EVACUATE
1. Pump system down to 28 in. of mercury and allow pump to
continue operating for an additional 15 minutes.
CHECK FOR TIGHT, DRY SYSTEM
(IF IT HOLDS DEEP VACUUM)
2. Close service valves and shut off vacuum pump.
3. Connect a nitrogen cylinder and regulator to system and
open until system pressure is 2 psig.
CHARGE SYSTEM
A95425
4. Close service valve and allow system to stand for 1 hr.
During this time, dry nitrogen will be able to diffuse
throughout the system, absorbing moisture.
G.
IMPORTANT: Check to be certain factory tubing on both indoor
and outdoor unit has not shifted during shipment. Ensure tubes are
not rubbing against each other or any sheet metal. Pay close
attention to feeder tubes, making sure wire ties on feeder tubes are
secure and tight.
VIII. MAKE ELECTRICAL CONNECTIONS
5. Repeat this procedure as indicated in Fig. 11. System will
then contain minimal amounts of contaminants and water
vapor.
LIQUID-LINE
FILTER-DRIER
LIQUID
SERVICE
VALVE
R-
Fig. 11—Triple Evacuation Method
FINAL TUBING CHECK
WARNING: To avoid personal injury or death, do not
supply power to unit with compressor terminal box cover
removed.
4 1 0A
Be sure field wiring complies with local and national fire, safety,
and electrical codes, and voltage to system is within limits shown
on unit rating plate. Contact local power company for correction of
improper voltage. See unit rating plate for recommended circuit
protection device.
NOTE: Operation of unit on improper line voltage constitutes
abuse and could affect unit reliability. See unit rating plate. Do not
install unit in system where voltage may fluctuate above or below
permissible limits.
NOTE: Use copper wire only between disconnect switch and
unit.
A97555
Fig. 9—Filter Drier with Sweat Adapter Tube and Liquid
Tube
—6—
recommended airflow and for adjustments to the manual switches
labeled SW1, A/C and CF on the control board refer to the furnace
Installation, Start-Up, and Operating Instructions. The
315AAV/315JAV utilizes a control center that allows the installing technician to select the proper airflows. The A/C switch
determines the airflow during high speed compressor operation.
Airflow for high and low speed can be calculated at either 350
CFM per ton or 400 CFM per ton based on the positions of SW1-5.
→ B. AIRFLOW SELECTION FOR 355MAV FURNACES
The 355MAV Condensing Variable-Speed Furnaces provide highand low-speed blower operation to match the capacities of compressor at high and low speeds. To select recommended airflow,
refer to the 355MAV Installation Instructions. The 355MAV
utilizes a control center that allows the installing technician to
select proper airflow. For adjustments to the manual switches
labeled A/C and CF and recommended switch positions, refer to
Furnace Installation Instructions for setting required airflow.
High-speed airflow is determined by the position of the A/C
switches, and low-speed airflow is determined by the position of
the CF switches.
→ C. AIRFLOW SELECTION FOR FK4 OR FV4 FAN COILS
The FK4 and FV4 provide high- and low-speed blower operation
to match the capacities of compressor at high and low speeds. To
select recommended airflow, refer to the FK4 or FV4 Installation
Instructions. The FK4 and FV4 utilize an EASY SELECT control
board that allows the installing technician to select proper airflow.
The ORANGE SYSTEM TYPE JUMPER wire should be set to
HP–EFF or HP–COMFORT. The BLUE AC/HP SIZE JUMPER
is used to select airflow to match the outdoor unit nominal size in
tons of cooling. The BLACK AC/HP CFM ADJUST jumper is
used to make slight adjustments to the selected airflow tonnage.
See the fan coil Installation Instructions for setting required
airflow. This fan coil has an adjustable blower off delay factory set
at 90 sec for high- and low-speed blower operation.
XI. START-UP
DISCONNECT
PER N. E. C. AND/ OR
LOCAL CODES
CONTACTOR
FIELD POWER
WIRING
FIELD GROUND
WIRING
GROUND
LUG
A91306
Fig. 12—Line Power Connections
NOTE: Install branch circuit disconnect of adequate size per
NEC to handle unit starting current. Locate disconnect within sight
from and readily accessible from unit, per Section 440-14 of NEC.
A. ROUTE GROUND AND POWER WIRES
Remove access panel and control box cover to gain access to unit
wiring. Extend wires from disconnect through power wiring hole
provided and into unit control box. Size wires per NEC but not
smaller than minimum wire size shown in Product Data Sheet.
WARNING: The unit cabinet must have as uninterrupted or unbroken ground to minimize personal injury if
an electrical fault should occur. The ground may consist
of electrical wire or metal conduit when installed in
accordance with existing electrical codes. Failure to
follow this warning can result in an electric shock, fire, or
death.
B. CONNECT GROUND AND POWER WIRES
Connect ground wire to ground connection in control box for
safety. Connect power wiring to leads provided as shown in Fig.
12.
CAUTION: To prevent compressor damage or personal
injury, observe the following:
• Do not overcharge system with refrigerant.
• Do not operate unit in a vacuum or at negative pressure.
• Do not disable low-pressure switch.
C. CONNECT CONTROL WIRING
Route 24v control wires through control wiring grommet and
connect to leads provided in control box. (See Fig. 13.)
Use No. 18 AWG color-coded, insulated (35°C minimum) wire. If
thermostat is located more than 100 ft from unit, as measured
along the control voltage wires, use No. 16 AWG color-coded wire
to avoid excessive voltage drop.
All wiring must be NEC Class 1 and must be separated from
incoming power leads.
The outdoor unit requires a minimum of 27va, 24v control power.
CAUTION: To prevent personal injury wear safety
glasses, protective clothing, and gloves when handling
refrigerant and observe the following:
• Back seating service valves are not equipped with
Schrader valves. Fully back seat (counter clockwise)
valve system before removing gage port cap.
D. FINAL WIRING CHECK
IMPORTANT: Check factory wiring and wire connections to
ensure terminations are secured properly. Check wire routing to
ensure wires are not in contact with tubing, sheet metal, etc.
IX.
INSTALL ELECTRICAL ACCESSORIES
A.
GENERAL
CAUTION: Do not vent refrigerant to atmosphere. Recover during system repair or final unit disposal.
Follow these steps to properly start up the system:
1. The outdoor unit is equipped with a crankcase heater which
operates when the compressor is OFF. Energize crankcase
heater 24 hr before starting unit. To energize heater only, set
indoor thermostat to OFF position and close power disconnect to unit.
2. Fully back seat (open) liquid and vapor tube service valves.
3. Unit is shipped with valve stem(s) front seated and caps
installed. Replace stem caps after system is opened to
refrigerant flow (back seated). Replace caps finger tight and
tighten additional 1/12 turn (20 ft-lb torque) with wrench.
Refer to the individual instructions packaged with kits or accessories when installing. The liquid line solenoid valve accessory is
available on these units. See Fig. 14 for wiring diagram.
See Fig. 13 for typical accessory wiring diagrams.
X.
MAKE AIRFLOW SELECTIONS
A. AIRFLOW SELECTION FOR 315AAV/315JAV FURNACES
The 315AAV/315JAV Non-Condensing Variable Speed Furnaces
provide high- and low-speed blower operation to match the
capacities of the compressor at high and low speeds. To select the
—7—
PROGRAMMABLE
THERMOSTAT
MODEL 2S
FV4
FK4
FAN COIL
DH
THERMIDISTAT
CONTROL
MODEL RH
TWO-SPEED
HEAT PUMP
J1
JUMPER
SINGLE-STAGE
FURNACE
TWO-SPEED
HEAT PUMP
RVS COOLING O/ W2
O
COOL/HEAT
STAGE 1
Y1
24 VAC HOT
R
R
FAN
G
G
HEAT STAGE 3 W/W1
W
W1
Y1
Y1
COOL/HEAT
STAGE 2
Y/Y2
Y
Y2
R
Y1/W2
COOL/HEAT
STAGE 1
Y1/W2
RVS COOLING
O/W2
O
O
FAN
G
G
COOL/HEAT
STAGE 2
Y/Y2
Y/Y2
Y2
24 VAC HOT
R
R
R
HEAT STAGE 3
W/W1
24 VAC COMM
C
C
C
W1
W1
J2 JUMPER
W2
24 VAC COMM
C
C
C
N/A
B
OUTDOOR
SENSOR
CONNECTION
S1
N/A
S2
OUTDOOR
SENSOR
CONNECTION
DHUM
N/A
HUM
HUMIDIFY
S1
FV4
FK4
FAN COIL
OUTDOOR
SENSOR
S2
See notes 1, 2, and 3
A01475
NON-PROGRAMMABLE
THERMOSTAT
MODEL 2S
HUMIDIFIER
(24 VAC)
B
See notes 1, 2, 3, 7, 8, 9, 10, and 11
A01422
TWO-SPEED
HEAT PUMP
PROGRAMMABLE
DUAL FUEL
THERMOSTAT
MODEL DF
SINGLE-STAGE
FURNACE
TWO-SPEED
HEAT PUMP
DH
J1 JUMPER
24 VAC HOT
R
R
24 VAC COMM
C
C
FAN
G
G
R
R
FAN
G
G
W/ W1
W
W1
Y/ Y2
Y
Y2
C
HEAT STAGE 3
COOL/HEAT
STAGE 2
Y/Y2
Y/Y2
HEAT STAGE 3
W/W1
W1
(FURNACE)
COOL/HEAT
STAGE 2
Y2
(COMPRESSOR HI)
J2 JUMPER
RVS COOLING
COOL/HEAT
STAGE 1
W2
W1
O/W2
O
O
Y1
Y1
Y1
N/A
B
OUTDOOR
S1
RVS COOLING
O/W2
O
COOL/HEAT
STAGE 1
Y1/W2
Y1
(COMPRESSOR LO)
24 VAC COM
C
N/A
B
RVS SENSING
S2
FV4/FK4
FAN COIL
C
OUTDOOR
SENSOR
S2
See notes 1, 2, 3, and 4
A01476
THERMIDISTAT
CONTROL
MODEL RH
C
L
S1
OUTDOOR
SENSOR
CONNECTIONS
SENSOR
CONNECTION
R
24 VAC HOT
R
See notes 1, 2, 3, 7, 8, and 12
A01423
THERMIDISTAT
CONTROL
MODEL RH
TWO-SPEED
HEAT PUMP
TWO-STAGE
FURNACE
WITH PSC
BLOWER MOTOR
TWO-SPEED
HEAT PUMP
RVS COOLING O/W2
O
O
RVS COOLING
O/W2
O
COOL/HEAT
STAGE 1
Y1
Y1
COOL/HEAT
STAGE 1
Y1/W2
Y1
W1
HEAT STAGE 3
W/ W1
W/W1
W1
Y/ Y2
Y/Y2
Y2
FAN
G
G
24 VAC HOT
R
Y1/W2
HEAT STAGE 3 W/W1
W1
COOL/HEAT
STAGE 2
W2
Y/Y2
J2 JUMPER
FAN
G
Y/Y2
24 VAC HOT
R
G
COOL/HEAT
STAGE 2
Y2
R
R
R
R
W2
REMOVE J1
DEHUMIDIFY
DHUM
DH
24 VAC COMM
C
C
HUMIDIFY
N/A
OUTDOOR
SENSOR
CONNECTION
HUM
24 VAC COMM
C
N/A
HUMIDIFIER
(24 VAC)
HUMIDIFY
B
S1
N/A
OUTDOOR
SENSOR
OUTDOOR
SENSOR
CONNECTION
S2
See notes 1, 2, 3, 6, 9, and 10
A01429
Fig. 13—Typical 24V Circuit Connections
—8—
C
C
C
DHUM
HUM
HUMIDIFIER
(24 VAC)
B
S1
OUTDOOR
SENSOR
S2
See notes 1, 2, 3, 5, 7, 8, 9, 10, and 11
A01426
THERMIDISTAT
CONTROL
MODEL RH
VARIABLE-SPEED
CONDENSING
FURNACE
PROGRAMMABLE
DUAL FUEL
THERMOSTAT
MODEL DF
TWO-SPEED
HEAT PUMP
RVS COOLING
O/W2
COOL/HEAT
STAGE 1
Y1/W2
HEAT STAGE 3
W/W1
W/W1
W1
COOL/HEAT
STAGE 2
Y/Y2
Y/Y2
Y2
FAN
G
G
24 VAC HOT
R
R
O
W2
Y1
Y1
VARIABLE
SPEED
CONDENSING
FURNACE
TWO-SPEED
HEAT PUMP
R
24 VAC HOT
R
R
FAN
G
G
W/ W1
W/ W1
W1
Y/ Y2
Y/ Y2
Y2
HEAT STAGE 3
(FURNACE)
COOL/HEAT
STAGE 2
(COMPRESSOR HI)
RVS COOLING
R
O
O/W2
DEHUM
COOL/HEAT
STAGE 1
DHUM
Y1/W2
Y1
Y1
(COMPRESSOR LO)
DEHUMIDIFY
24 VAC COMM
DHUM
COM
C
HUM
HUM
HUMIDIFY
W2
C
HUMIDIFIER
(24 VAC)
OUTDOOR
SENSOR
CONNECTION
C
COM
N/A
B
HUM
RVS SENSING
B
N/A
24 VAC COMM
OUTDOOR
SENSOR
S1
OUTDOOR
SENSOR
CONNECTIONS
S2
L
THERMIDISTAT
CONTROL
MODEL RH
OUTDOOR
SENSOR
S1
S2
See notes 1, 2, 3, 5, 7, 8, 9, 10, 11, and 13
A03033
VARIABLE SPEED 80%
NON-CONDENSING FURNACE
See notes 1, 2, 3, 5, 7, 8, and 12
A03036
PROGRAMMABLE
DUAL FUEL
THERMOSTAT
TWO-SPEED
HEAT PUMP
RVS COOLING
O/W2
Y1
O
HEAT/COOL
STAGE 1
Y1/W2
W2
Y1
HEAT STAGE 3
W/ W1
W/W1
W1
HEAT/COOL
STAGE 2
Y/ Y2
Y/Y2
Y2
FAN
G
G
24 VAC HOT
R
R
C
TWO-STAGE
FURNACE
24 VAC HOT
R
R
FAN
G
G
HEAT STAGE 3 W/W1
(FURNACE)
COOL/HEAT
STAGE 2
Y/Y2
TWO-SPEED
HEAT PUMP
R
W/W1
W1
Y/Y2
Y2
(COMPRESSOR HI)
O
RVS COOLING O/W2
COOL/HEAT
STAGE 1 Y1/W2
R
Y1
(COMPRESSOR LO)
24 VAC COM
C
W1
C
COM
24 VAC COM
HUM
DEHUMIDIFY
C
C
HUM
C
DHUM
N/A
B
RVS SENSING
L
OUTDOOR
SENSOR
CONNECTION
S1
DHUM
PL9-10
HUMIDIFY
N/A
OUTDOOR
SENSOR
CONNECTIONS
HUM
HUMIDIFIER
(24 VAC)
B
S1
OUTDOOR
SENSOR
SUGGESTED DIP
SWITCH SETTINGS
See notes 1, 2, 3, 5, 7, 8, and 12
A01424
VARIABLE SPEED 80%
NON-CONDENSING FURNACE
PROGRAMMABLE
DUAL FUEL
THERMOSTAT
MODEL DF
TWO-SPEED
HEAT PUMP
O
RVS COOLING
O/W2
Y1
COOL/HEAT
STAGE 1
Y1/W2
W2
Y1
W/ W1
W/W1
W1
Y2
LEGEND
24 VOLT FACTORY WIRING
(COMPRESSOR LO)
(FURNACE)
COOL/HEAT
Y/ Y2
Y/Y2
(COMPRESSOR HI)
STAGE 2
FAN
G
G
24 VAC HOT
R
R
R
24 VAC COMM
C
COM
C
N/A
B
RVS SENSING
OUTDOOR
SENSOR
CONNECTIONS
S2
S2
See notes 1, 2, 3, 5, 7, 8, 9, 10, and 11
A03034
HEAT STAGE 3
OUTDOOR
SENSOR
24 VOLT FIELD WIRING
FIELD SPLICE CONNECTION
RELAY SPDT, PILOT DUTY
24-V COIL (HN61KK324)
OR EQUIVALENT
HUM
R1
H
DHUM
L
S1
OUTDOOR
SENSOR
HUMIDISTAT, OPENS ON
HUMIDITY RISE (HL38MG026)
AFS
AIRFLOW SELECTOR
Y1
RELAY COIL
S2
See notes 1, 2, 3, 5, 7, 8, and 12
A03035
→
Fig. 13—Typical 24V Circuit Connections (Cont) and Wiring Diagram Legend
—9—
A01222
WIRING DIAGRAM NOTES:
1. Wiring must conform to NEC or local codes.
2. Underlined letter on thermostat terminal indicates its usage. For example: O/W2 means O is energized in cooling mode.
3. Refer to indoor unit Installation Instructions for any additional features and wiring information.
4. Non-Programmable Model 2S01–B, when used in heat pump installations (jumper R19 NOT cut), uses O/W2 to control reversing valve.
5. Furnace must control its own second-stage operation via furnace control algorithms. Refer to furnace Installation Instructions for proper
setup.
6. To activate dehumidify function on FK4 or FV4, remove J1 jumper at fan coil control board.
7. Heat pump MUST have a high-pressure switch for dual fuel applications.
8. Outdoor air temperature sensor must be attached in all dual fuel applications.
9. Thermidistat Dip Switch No. 1 should be set in ON position for heat pump installations.
10. Thermidistat Dip Switch No. 2 should be set in the ON position for dual capacity compressor operation.
11. Thermidistat Configuration Option No. 10 “Dual Fuel Selection” must be turned ON in all dual fuel applications.
12. Dual Fuel Dip Switch–D (no. 4) must be set in the ON position for dual capacity compressor operation.
13. The DE jumper located next to the DHUM terminal must be removed to enable the DEHUM input.
NOTE: If unit has not operated within the past 12 hr or following a unit power-up, upon the next thermostat high- or low-speed demand, unit
operates for a minimum of 5 minutes on high speed.
XII.
4. Close electrical disconnects to energize system.
CHECK CHARGE
5. Set room thermostat at desired temperature. Be sure the set
point is below indoor ambient and is set low enough to
energize desired speed.
WARNING: Service valve gage ports are not equipped
with Schrader valves. To prevent personal injury, make
sure gage manifold is connected to the valve gage ports
before moving valves off fully back seated position. Wear
safety glasses and gloves when handling refrigerant.
6. Set room thermostat to COOL or HEAT and fan control to
AUTO or ON as desired. Wait for appropriate time delay(s).
Operate unit for 15 minutes. Check refrigerant charge.
NOTE: Bryant electronic thermostats are equipped with a 15
minute staging timer. This timer prevents the dual capacity system
from operating at high capacity until unit has been operating in low
capacity for 15 minutes unless there is at least a 5°F difference
between room temperature and thermostat set point. To force high
capacity, adjust the set point at least 5° below room ambient for
cooling or 5° above room ambient for heating.
A.
UNIT CHARGE
Factory charge is shown on unit rating plate. To check charge in
cooling mode, refer to Cooling Only Procedure. To charge in
heating mode, weigh the charge in.
FK4/FV4
FAN COIL
TWO-SPEED
HEAT PUMP
DH
Y1
Y2
J1 JUMPER
24 VAC HOT
R
R
R
24 VAC COM
C
C
C
FAN
LLS
G
G
COOL/HEAT
STAGE 2
Y/Y2
Y/Y2
HEAT STAGE 3
W/W2
W1
Y2
Y2
J2 JUMPER
W2
RVS COOLING
W1
O/W2
O
O
COOL/HEAT
STAGE 1
Y1
Y1
Y1
N/A
B
OUTDOOR
SENSOR
S1
CONNECTION
Y1
S2
A00333
Fig. 14—Typical Solenoid Valve Wiring
—10—
NOTE: In heating mode, check refrigerant charge only when
pressures are stable. If accessory vapor pressure switch is applied
and operating conditions cause vapor pressure switch and thereby
outdoor fan to cycle, check refrigerant charge in cooling or lower
indoor dry bulb temperature. If in doubt, remove charge and weigh
in correct refrigerant charge.
NOTE: When charging is necessary during heating season,
charge must be weighed in accordance with unit rating plate ±0.6
oz/ft of 3/8-in. liquid line above or below 15 ft respectively.
EXAMPLE:
To calculate additional charge required for a
25-ft line set:
25 ft - 15 ft = 10 ft X 0.6 oz/ft = 6 oz of
additional charge.
Adjust charge in both heating and cooling by following procedure
shown on charging tables located on pink charging label on back
side of access panel.
NOTE: Unit is to be charged in high capacity only. Charging in
low capacity may cause compressor chattering and possible
damage to the compressor.
B. COOLING ONLY PROCEDURE
1. Operate unit a minimum of 15 minutes before checking
charge.
2. Measure liquid service valve pressure by attaching an
accurate gage to service port.
3. Measure liquid line temperature by attaching an accurate
thermistor type or electronic thermometer to liquid line near
outdoor coil.
4. Refer to charging label for required subcooling temperatures.
5. Refer to Table 3. Find the point where required subcooling
temperature intersects measured liquid service valve pressure.
6. To obtain required subcooling temperature at a specific
liquid line pressure, add refrigerant if liquid line temperature is higher than indicated or reclaim refrigerant if
temperature is lower. Allow a tolerance of ± 3°F.
C. HEATING CHECK CHARGE PROCEDURE
To check system operation during heating cycle, refer to the
Heating Pump Charging Instructions on outdoor unit. This chart
indicates whether a correct relationship exists between system
operating pressure and air temperature entering indoor and outdoor
units. If pressure and temperature do not match on chart, system
refrigerant charge may not be correct. Do not use chart to adjust
refrigerant charge.
XIII. SYSTEM FUNCTIONS AND SEQUENCE OF OPERATION
The outdoor unit control system has special functions. The
following is an overview of the two-speed control functions:
CEBD430439-03A
SS0ID
HI
LO
HP/AC
SEV
RVS
C
A. COOLING OPERATION
This product utilizes a 2-stage cooling indoor thermostat. With a
call for first stage cooling (Yl), the outdoor fan and low capacity
compressor are energized. If low capacity cannot satisfy cooling
demand, high capacity is energized (Yl and Y2 or just Y2) by the
second stage of indoor thermostat. After second stage is satisfied,
the unit returns to low-capacity operation until first stage is
satisfied or until second stage is required again. When both one
stage and two stage cooling are satisfied, the compressor will shut
off.
NOTE: Outdoor fan motor will continue to operate for one
minute after compressor shuts off, when outdoor ambient is greater
than 100°F.
C2
R38
R33
R9
J1
1
LPS
PL2
1
R65
1
PL3
HPS
C31
R61
PL4
OAT
PL1
OCT
FORCED
DEFROST
PL5
PWM2
DEFROST
TIME (MIN)
R39
R44
R42
PWM1
C18
BRN
VC
60
C16
60
1 2
90
30
R36
BLU
VH
0
Y2
Y1
BLK
W1
C O M M S TAT U S
C
CEPL130439-01
K1
R89
R85
A
B
YEL
D52
D51
R
C
D
R86
R91
R87
RED
L2 ODF
120
30
CCH
S1
CESO130078-00
A00379
Fig. 15—Control Board
—11—
NOTE: When two-speed unit is operating in low-capacity cooling, system vapor (suction) pressure will be higher than a standard
single-speed system or high-speed operation. This normal operation is due to the reduced capacity operating with typically larger
indoor and outdoor coils.
B.
D. STATUS FUNCTION LIGHTS
A system control STATUS function light is located on the outdoor
unit control board. (See Fig. 15). The STATUS light provides
signals for several system operations. See Table 4 for codes and
definitions. Table 4 also provides the order of signal importance.
NOTE: Only one code will be displayed on the outdoor unit
control board (the most recent, with the highest priority).
E. FACTORY DEFAULTS
Factory defaults have been provided in the event of failure of
outdoor air thermistor and/or outdoor coil thermistor. Refer to
Table 6 for default and function.
F. COMPRESSOR OPERATION
ONE MINUTE SPEED CHANGE TIME DELAY
When compressor changes speeds from high to low or low to high,
there is a 1-minute time delay before compressor restarts. The
outdoor fan motor remains running.
C.
HEATING OPERATION
This product utilizes a 3-stage heating indoor thermostat. With a
call for first stage heating (Y1), the outdoor fan and low capacity
compressor are energized. If low capacity cannot satisfy heating
demand, high capacity is energized (Y1 and Y2) by the second
stage of the indoor thermostat. Auxiliary or back up heat is
controlled by third stage (W1). After second stage of heat is
satisfied, the unit returns to low capacity operation until first stage
is satisfied or until second stage is required again. When both one
stage and two stage heating are satisfied, the compressor will shut
off. See thermostat Installation Instructions for more staging
information.
When the compressor operates in two-capacity operation, the
motor rotates clockwise. Both the lower and upper pistons are
eccentric with the rotating crankshaft, and both compress refrigerant. When the compressor operates in single capacity the motor
reverses direction (rotates counterclockwise). The lower piston
becomes idle and the upper piston compresses refrigerant. During
single-capacity operation the “start” and “run” windings are
reversed.
G. CRANKCASE HEATER OPERATION
The two-speed control energizes the compressor crankcase heater
during unit’s off cycle.
H. OUTDOOR FAN MOTOR OPERATION
The two-speed control energizes outdoor fan any time compressor
is operating. The outdoor fan remains energized during the
1-minute speed change time delay and if a pressure switch or
compressor overload should trip. Outdoor fan motor will continue
to operate for one minute after the compressor shuts off when the
outdoor ambient is greater than 100°F.
TABLE 4—LED CONTROL FUNCTION LIGHT CODE
NOTE: If unit has not operated within the past 12 hr or following
a unit power-up, upon the next thermostat high- or low-speed
demand, unit operates for a minimum of 5 minutes on high
speed.
THERMISTOR CURVE
90
CODE
Constant flash
No pause
1 flash
w/pause
2 flashes
w/pause
3 flashes
w/pause
4 flashes
w/pause
3 flashes
pause
4 flashes
5 flashes
pause
1 flash
5 flashes
w/pause
2 flashes
6 flashes
w/pause
Constant light
No pause
No flash
RESISTANCE (KOHMS)
80
70
60
50
40
30
20
10
0
0
20
40
60
80
TEMPERATURE (DEG. F)
100
120
A91431
Fig. 16—Resistance Values Versus Temperature
Control Box
Side of Unit
DEFINITION
No demand
Stand by
*
10
Low-speed operation
9
High-speed operation
8
Outdoor ambient thermistor failure
7
Outdoor coil thermistor failure
6
Thermistor out of range†
5
Low pressure switch trip
4
High pressure switch trip
3
Compressor VC/VH trip
2
Board failure
1
* Function light signal order of importance in case of multiple signal request; 1
is most important.
† Check both thermistors to determine which is faulty.
THERMISTOR PLACED
UNDERNEATH BASE PAN
(ATTACHED TO BASE PAN
WITH ADHESIVE)
A02218
Fig. 17—View from Top of Base Pan
—12—
TABLE 5—DEFROST DIP SWITCH SETTINGS
TIME
30
60
90
120
DIP SWITCH #1
up
down
down
up
DIP SWITCH #2
down
up
down
up
After termination of a defrost cycle, the outdoor fan delays come
on for 20 sec. This allows refrigerant system to recover outdoor
coil heat and minimize the “steam cloud” effect.
I.
3. Display the appropriate error code on the status light (see
Table 4).
4. After a 15 minute delay, if Yl or Y2 inputs are on and the
LPS or HPS is reset, energize appropriate compressor
contactor, either low or high.
DEFROST TIME SELECTION
The defrost interval can be field selected, dependent on local or
geographical requirements. It is factory set at 90 minutes but can
be changed to either 30, 60, or 120 minutes. To select defrost time,
set dip switches located on the left side of the unit board (See Fig.
15). See Table 5 for Defrost Dip Switch Settings.
J.
5. If LPS or HPS has not closed after 15 minute delay, outdoor
fan is turned off. If the open switch closes anytime after the
15-minute delay, then resume operation on call for Y1
and/or Y2.
N.
DEFROST
MAJOR COMPONENTS
The dual capacity control logic for defrost function is the standard
time and temperature initiated, time or temperature terminated.
Defrost only occurs at outdoor temperatures less than 50°F. The
control initiates defrost when outdoor coil thermistor is 30°F (±2°)
or less, and selected defrost time (interval) has been accumulated
during unit operation. Termination occurs when coil thermistor
reaches 80°F (±5°) or defrost period reaches a maximum of 10
minutes. Defrost will occur at the compressor capacity that is being
called for. During defrost, unit operates in high or low capacity,
energizes reversing valve O and auxiliary heat W2, and deenergizes outdoor fan. Upon termination, there is a 20-sec delay in
outdoor fan being energized.
TWO-SPEED CONTROL
The two-speed control board controls the following functions:
• Low- and high-compressor contactor operation
• Outdoor fan motor operation
• Crankcase heater operation
• Compressor protection
• Pressure switch monitoring
• Time delays
• Time/temperature defrost
• Defrost interval selection
• Electric heat operation during defrost mode
K. FIELD-INITIATED FORCED DEFROST
By placing a jumper across forced defrost terminals (See Fig. 15)
for a minimum of 5 sec and then removing it, a defrost cycle can
be initiated. The cycle occurs only if outdoor ambient is less than
50°F, regardless of outdoor coil temperature. The cycle terminates
when coil thermistor reaches 80°F (±5°) or defrost period reaches
a maximum of 10 minutes.
FIELD CONNECTIONS
The two-speed dual capacity control received 24v low-voltage
control system inputs through the screw connections on the left
side of the control board.
TWO-SPEED DUAL CAPACITY COMPRESSOR
The two-speed dual capacity compressor contains motor windings
that provide 3500 RPM operation. Refer to Table 7 for correct
winding resistance.
L. COMPRESSOR VOLTAGE FAILURE (6 FLASHES)
The control senses the voltage of the compressor run winding. If
compressor voltage (Vc) is less than 90v when control board is
calling for compressor operation, control shuts compressor off for
15 minutes with outdoor fan running. After 15 minutes (provided
there is a call for Y1 or Y2), control attempts to start compressor.
During this time, a code of 6 flashes appears at control board. If Vc
trip occurs 3 consecutive times during a Y1 request, then low
capacity operation is locked out and control responds to Y2
requests until a reset occurs. If 3 consecutive trips occur in a
combination of Yl and Y2 or all Y2 requests, then both low and
high capacity operation will be locked out. The compressor voltage
failure (6 flashes) can be caused by:
• compressor internal overload trip (refer to Table 7 for correct
winding)
COMPRESSOR INTERNAL RELIEF
The compressor is protected by an internal pressure relief (IPR)
which relieves discharge gas into compressor shell when differential between suction and discharge pressures exceeds 525 psi. The
compressor is also protected by an internal overload attached to
motor windings.
COMPRESSOR CONTROL CONTACTORS
Low and High capacity contactor coils are 24 volts. The electronic
control board controls the operation of the low speed (C-L) and the
high speed (C-H) contactors.
O. TEMPERATURE THERMISTORS
Thermistors are electronic devices which sense temperature. As
the temperature increases, the resistance decreases. Thermistors
are used to sense outdoor ambient and coil temperature. Refer to
Fig. 16 for resistance values versus temperature.
If the outdoor ambient thermistor or coil thermistor should fail, a
fault code appears at electronic control. The crankcase heater is
turned on during all off cycles.
IMPORTANT: OUTDOOR AIR THERMISTOR PLACEMENT
Mount outdoor air thermistor underneath unit base pan lip on
control box side of unit as shown in Fig. 17. Attach to base pan
with adhesive tape or other field expedient means.
IMPORTANT: If outdoor air thermistor is nor properly placed
underneath base pan, unit may have nuisance thermistor out of
range faults.
• no 208/230 volt power supply to outdoor unit
• failed compressor contactor(s)
• failure of start relay to pick-up properly.
• improper wiring.
M. PRESSURE SWITCH PROTECTION
The outdoor unit is equipped with high- and low-pressure
switches. If the control senses the opening of the high or low
pressure switch, it will respond as follows:
1. De-energize the compressor hi or low speed contactor,
2. Keep the outdoor fan operating for 15 minutes,
TABLE 6—FACTORY DEFAULTS
FAILED COMPONENT
FUNCTION
Ambient Thermistor
Defrost Initiation
Outdoor Coil Thermistor
Defrost Initiation and Termination
—13—
DEFAULT
Defrost is initiated based on coil
temperature and time.
Defrost occurs at each time interval, but
terminate after 5 minutes
XIV. FINAL CHECKS
IMPORTANT: Before leaving job, be sure to do the following:
2. Tighten service valve stem caps to 1/12-turn past finger
tight.
1. Ensure that all wiring and tubing is secure in unit before
adding panels and covers. Securely fasten all panels and
covers.
3. Leave User’s Manual with owner. Explain system operation
and periodic maintenance requirements outlined in manual.
4. Fill out Dealer Installation Checklist and place in customer
file.
TABLE 7—TWO-SPEED COMPRESSOR
(WINDING RESISTANCE AT 70°F ± 20°)
WINDING
Start (S-C)
Run (R-C)
2 TON
2.280
0.770
3 TON
1.850
0.745
4 TON
1.459
0.552
CARE AND MAINTENANCE
For continuing high performance and to minimize possible equipment failure, periodic maintenance must be performed on this
equipment. Frequency of maintenance may vary depending upon
geographic areas, such as coastal applications.
5 TON
0.740
0.356
—14—
A03030
→
Fig. 18—Wiring Diagram—024, 036, 048
—15—
L1
208 / 230 1 - 60
POWER SUPPLY
BLK
L2
YEL
BLK
CH
13
BLK
CL
11
11
BLU
DUAL CAPACITY
CONNECTION DIAGRAM
RED
EQUIP GND
21
23
RVS
21
YEL
NOTE #11
COMP
BRN
BLU
BLU
BRN
PL1
1
2
HP/AC C
3
4
5
SEV RVS C
HPS 1
PL4 2
OAT
1
2
PL5
COMM STATUS OCT 4
5
A B C D
VC
VH
ODF
L2
CCH
BRN
START
CAP
LPS
YEL/PNK
C
COMP
CAP
YEL/PNK
HPS
DEFROST
TIME (MIN)
S
BRN
1 2
HI LO PL2
LPS
1
PL3 2
3
FORCE
DEFROST
C
BRN
H
BLU/PNK
BLU/PNK
BLK
-t∞
YEL
1
5
OAT
BLU
2
BLK
BRN
YEL
RED
R
BLU
ORN ORN
BLK
BLU
BLK
-t ∞
OCT
BLU
START
RELAY
BRN
BRN
BRN
YEL
BLU
BLK
BLK
YEL
FAN CAP
BRN
OFM
BLK
YEL
RED
RED
CCH
TO INDOOR UNIT
A03031
→ Fig. 19—Wiring Diagram—060
© 2003 Bryant Heating & Cooling Systems 7310 W. Morris St. Indianapolis, IN 46231
—16—
Printed in U.S.A.
698b244
Catalog No. 5369-812