Bryant OM 17-101 Thermostat User Manual

TITAN SINGLE™
INSTALLATION & OPERATING GUIDE
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
To ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit
the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain
the latest catalog and manual updates. Contact Bunn-O-Matic Corporation at 1-800-286-6070 to obtain a
paper copy of the required Illustrated Parts Catalog mailed via U.S. Postal Service.
40885.0000E
5/12 ©2008 Bunn-O-Matic Corporation
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY
Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:
1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal servers
and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor.
2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below:
a) Electronic circuit and/or control boards - parts and labor for 3 years.
b) Compressors on refrigeration equipment - 5 years parts and 1 year labor.
c) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis - parts
and labor for 4 years or 40,000 pounds of coffee, whichever comes first.
These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be
commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the
applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured
by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation,
improper maintenance or repair, non periodic cleaning and descaling, equipment failures related to poor water quality,
damage or casualty. In addition, the warranty does not apply to replacement of items subject to normal use including but
not limited to user replaceable parts such as seals and gaskets. This warranty is conditioned on the Buyer 1) giving BUNN
prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Office
Box 3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an
authorized BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under
warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make
modifications to this warranty or to make additional warranties that are binding on BUNN. Accordingly, statements by such
individuals, whether oral or written, do not constitute warranties and should not be relied upon.
If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the
applicable parts and labor warranty periods specified above) to repair the defective components, provided that this repair
is done by a BUNN Authorized Service Representative; or 2) shall replace the equipment or refund the purchase price for
the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS
EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION
AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.
In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of
use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities
or services, or any other special, incidental or consequential damages.
392, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, BrewWIZARD, BUNN Espress, BUNN
Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the stylized red line, BUNNlink, Bunn-OMatic,
Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design, Cool Froth, DBC, Dr. Brew stylized Dr. design,
Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, iMIX, Infusion Series, Intellisteam, My Café, Phase Brew, PowerLogic, Quality Beverage Equipment Worldwide, Respect Earth, Respect Earth with
the stylized leaf and coffee cherry design, Safety-Fresh, savemycoffee.com, Scale-Pro, Silver Series, Single, Smart Funnel,
Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment Worldwide, ThermoFresh,
Titan, trifecta, Velocity Brew, A Partner You Can Count On, Air Brew, Air Infusion, Beverage Bar Creator, Beverage Profit
Calculator, Brew better, not bitter., BUNNSource, Coffee At Its Best, Cyclonic Heating System, Daypart, Digital Brewer
Control, Nothing Brews Like a BUNN, Pouring Profits, Signature Series, Tea At Its Best, The Horizontal Red Line, Ultra are
either trademarks or registered trademarks of Bunn-O-Matic Corporation.
INTRODUCTION
This equipment will brew coffee into an awaiting server or airpot. The brewer may have an auxillary hot water
faucet. It is only for indoor use on a sturdy and level counter or shelf. Please install in an area where there are
no water jet devices.
This brewer can be programmed to adjust different functions of the brewing process, such as brew temperature, brew volumes, bypass percentages, pulse brew, etc. Other features are Energy Savings mode, Freshness
Timer and Clean Alert.
Page 2
40885 030912
USER NOTICES
Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should be
kept in good condition. Replace any unreadable or damaged labels.
WARNING
HAZARDOUS
VOLTAGE
DISCONNECT FROM
POWER SOURCE
BEFORE REMOVING!
12559.0003
#00986.0000
#00658.0000
120/208 V, 40.1 A, 8200 W
1PH, 3-Wire + GND, 50/60HZ
29710.0015B
Optional Field Wiring
29710.0015
#37881.0000
Optional Field Wiring
29710.0019A
120/240 V, 35.0 A, 8200 W
1PH, 3-Wire + GND, 60HZ
As directed in the International Plumbing Code of the
International Code Council and the Food Code
Manual of the Food and Drug Administration (FDA),
this equipment must be installed with adequate
backflow prevention to comply with federal, state
and local codes. For models installed outside the
U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area.
#00656.0001
29710.0019
MAIN ON/OFF
SWITCH
230 V, 32.8 A, 7550 W
1PH, 2-Wire + GND, 50/60HZ
29710.0020A
Optional Field Wiring
00824.0002
29710.0020
39803.0000
00824.0001
03408.0004
Page 3
Artwork for P/N: 39803.0000
Artwork Rev: A
Drawn: REF
Date: 02/26/07
03409.0004
40885 112611
ELECTRICAL REQUIREMENTS
WARNING - If the power cord is ever damaged, it must be replaced by the manufacturer or its service agent with
a special cord available from the manufacturer or its service agent in order to avoid a hazard.
Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements.
BLU
RED
BLK
L1
L3
WHI
RED
N
BLU
TO MACHINE
BLK
WHI
L2
L3
N
WHI
BLU
RED
L2
FROM POWER SOURCE
L1
GREEN
GREEN
FOR SINGLE PHASE OPERATION
MOVE BLU WIRE INTO TERMINAL
BLOCK WITH BLACK WIRE.
CONNECT INPUT WIRING TO:
L1, L2 & N FOR 120/208V &
120/240V MODELS,
L1 & N for 230V MODELS.
BLK
N
L3
L2
L1
GREEN
GREEN
120/208 and 120/240 volt ac
three phase, 50/60 Hz models
400/230V volt ac three phase,
50/60 Hz models
Note: This electrical service consists of 4 current carrying conductors (Neutral, L1, L2 and
L3) and a separate conductor for earth ground.
Note: This electrical service consists of 4 current carrying conductors (Neutral, L1, L2 and
L3) and a separate conductor for earth ground.
SYSTEM
VOLTAGE
208
240
V1
208
240
SYSTEM
VOLTAGE
V1
400
400
230
V2
120
120
V2
230
230
L1, L2, L3, are the 3 phases
V1 = Phase to phase voltage, between any 2 phases.
V2 = Phase to neutral voltage, L1 to neutral must be 230V.
L1, L2, L3, are the 3 phases
V1 = Phase to phase voltage, between any 2 phases.
V2 = Phase to neutral voltage, L1 to neutral must be 120V.
ELECTRICAL HOOK-UP
CAUTION – Improper electrical installation will damage electronic components. Damage caused by incorrect
electrical connections is not covered by warranty.
1.
2.
3.
4.
5.
6.
An electrician must provide electrical service as specified in conformance with all local, state and federal
electrical codes.
Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.
NOTE - The brewer is shipped without a plug on the power cord. Qualified service personnel must select
and install the proper UL listed grounding type attachment plug specified on the rear of the brewer.
Install the specified plug on the attached power cord.
Remove the front access panel to gain access to the terminal block.
Connect the brewer to the power source and verify the voltage at the terminal block before proceeding.
If plumbing is to be hooked up later be sure the brewer is disconnected from the power source. If plumbing
has been hooked up, the brewer is ready for Initial Set-Up.
Page 4
40885 080108
CE REQUIREMENTS
• This appliance must be installed in locations where it can be overseen by trained personnel.
• For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C.
• Appliance shall not be tilted more than 10° for safe operation.
• An electrician must provide electrical service as specified in conformance with all local and national codes.
• This appliance must not be cleaned by water jet.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given instructions concerning use of
this appliance by a person responsible for its safety.
• Children should be supervised to ensure they do not play with the appliance.
• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel with
a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard.
PLUMBING REQUIREMENTS
This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi (138
and 620 kPa) with a minimum of 4.0 gpm from a 1⁄2" or larger supply line. A shut-off valve should be installed
in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to
reduce it to 50 psi (345 kPa). The water inlet fitting is 3⁄8" flare.
NOTE - Bunn-O-Matic recommends 3⁄8" copper tubing for all installations from the 1⁄2" water supply line. A tight
coil of copper tubing in the water line will facilitate moving the brewer to clean the counter top. Bunn-O-Matic
does not recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the
supply line by this type of device may restrict water flow.
As directed in the International Plumbing Code of the International Code Council and the Food Code
Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate
backflow prevention to comply with federal, state and local codes. For models installed outside the
U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area.
PLUMBING HOOK UP
NOTE - If a backflow preventer is required by code, a shock arrestor should be installed between
backflow preventer and dispenser. Installing the shock arrestor as close to dispenser as possible
will provide best results.
1.
2.
3.
4.
Remove the shipping cap from the fitting on the bottom of the brewer.
Attach the flare tube assembly (supplied separately with the brewer) to the fitting using the
copper flare gaskets on each end as shown in illustration.
Flush the water line and securely attach it to the flare elbow fitting.
Turn on the water supply.
P4290
TANK DRAIN
1. Remove screws that secure the front access panel. Remove the panel.
2. Unfasten the hose clamp at the end of the drain hose. Remove the plug.
3. Place the end of the drain hose in a drain or in a container that has a minimum capacity of 10.0 gallons
(37.85 liters).
4. Release the white clamp to drain water from the tank.
5. When tank is empty, close the white clamp, replace the plug, and tighten the clamp at the end of the drain
hose.
6. Replace the front panel and tighten screws.
Page 5
40885 020112
OPERATING CONTROLS
B
ENABLE
ON / OFF
C
G
E
READY TO BREW
WATER TEMP: 200°
BREW
LARGE
BREW
D
SMALL
F
H
P3894
A. MAIN ON/OFF SWITCH
This switch, located under the brewer in front of the right rear leg, turns power on and off to all components
in the brewer.
B. ON/OFF SWITCH (ENABLE BREW)
Pressing the "ON/OFF" switch will alternately turn the brew components on and off. Pressing this switch during
the brew cycle will interrupt the brew cycle, stopping the flow of water. Pressing this switch during programming
of the brewer will exit the setup and return to the main screen.
C. PROGRAMMING (left)
This hidden switch can be used to scroll backwards through the function list while in programming mode.
D. BREW
When the ON/OFF (Enable Brew) switch is ON and the main screen is visible, momentarily pressing and
releasing this switch will begin a brew cycle on the selected side.
E. PROGRAMMING (right)
Pressing and holding this switch allows entry into the programming menus. Pressing and releasing the switch
steps through each function screen while in the programming mode.
F. BATCH SELECTOR SWITCHES
Pressing the switch corresponding to the Half or Full batch selects the amount of product to be brewed.
Pressing a different switch after a brew cycle has been initiated does not change the brew batch in progress.
Light indicates the selected batch to brew. Also used in programming to adjust settings on both batch sizes.
G. FUNCTION SCREEN
This is the display which shows the various functions of the brewer and allows the programming to be accomplished.
H. FUNCTION SCREEN SWITCHES
These are hidden switches which are used to program the brewer when in the programming mode.
Page 6
40885 080108
INITIAL SET-UP
1. Insert an empty funnel into the funnel rails of the brew
station.
2. Place an empty server under the funnel.
3. Connect the brewer to the power source. Make sure the
ON/OFF (Enable Brew) switch is ON (LED will be lit).
4. Water will flow into the tank and stop when the tank is
filled to its capacity. Display will show PLEASE WAIT...
TANK FILLING until tank is filled with water.
5. Wait approximately twenty-five minutes for the water in
the tank to heat to the proper temperature. Display will
show READY TO BREW...WATER TEMP: 205° when tank
is at operating temperature. Some water may drip from
the funnels during this time; this is due to expansion and
should not occur thereafter.
NOTE: Brew water temperature is factory set at 205° F
(96.1° C). Refer to Set Temp and Set Ready sections of
the Programming Manual on the Bunn-O-Matic website,
at www.bunn.com should the water temperature need to
be increased or decreased. When brew water temperature
is changed, ready temperature will need to be increased
or decreased also.
6. Place a small vessel beneath the faucet and open the
faucet handle. Release it when you hear the tank refilling.
7. Water volumes and flow settings have been preset at the
factory. Refer to adjustments for the Set Brew Volumes
or Calibrate Flow section of the Programming Manual on
the Bunn-O-Matic website, at www.bunn.com should the
volume need to be increased or decreased.
8. The brewer is now ready for use in accordance with the
instructions for Coffee Brewing.
205° F (96.1° C)
VIEWING ASSET & SERIAL NUMBER
1. To view the asset number of the machine, press and hold the left hidden switch until the display reads:
ANXXXXXX...ASSET NUMBER. Release the left hidden switch.
2. After a 5 second delay, the display will read: DTTNXXXXXX. This is the serial number of the machine.
Page 7
40885 111611
COFFEE BREWING
Fold over top
1. Begin each brew cycle with a clean empty brew funnel.
edge of filter
2. Insert a BUNN filter into the funnel.
NOTE: The funnels are equipped with 4 wire loops that can be folded
over top edge of filter if desired, to prevent filter from folding in
during the brew cycle.
3. Pour the fresh coffee into the filter and level the bed of grounds by
gently shaking.
4. Slide the funnel into the funnel rails until it stops.
5. Place an empty server under the funnel.
6. The ON/OFF (Enable Brew) switch must be ON. Select the desired
batch size.
7. Momentarily press and release the BREW button. There may be
certain situations in which the brew cycle will not begin when BREW
is pressed:
a. SWITCH NOT ON - ON/OFF must be ON.
b. BREW TEMPERATURE TOO LOW - wait until heated or cancel BREW LOCKOUT option.
c. CHECK FUNNEL - remove funnel, empty previously brewed grounds and replace with fresh.
d.DISABLED - select different brew button or batch size.
8. If none of the above messages are displayed, the display will read NOW BREWING and show the time remaining in the brew cycle.
9. Following the brew will be a countdown of drip time DRIPPING which shows the time remaining until the
coffee no longer drips from the funnel tip.
10.Carefully remove the brew funnel and discard the grounds and filter only after visible dripping stops.
Page 8
40885 080108
CLEANING
1. The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all
surfaces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device.
2. Check and clean each sprayhead. The sprayhead holes must always remain open.
NOTE: Any buildup on the sprayhead may restrict water flow, and impact your coffee brewing. For consistently great coffee, clean sprayheads weekly. Upon visual inspection it may appear that light passes through
all holes in the sprayhead plate, but a thin film of residue can pass light and still impede water flow.
3. Remove sprayhead from brewer. Disassemble by removing the seal.
4. Use the pointed end of sprayhead cleaning tool to remove any mineral deposits from the sprayhead holes.
5. Insert the long end of sprayhead cleaning tool into the sprayhead fitting, and rotate several times to remove
any mineral deposits from the fitting.
6. Insert the short end of sprayhead cleaning tool into the bypass fittings, and rotate several times to remove
any mineral deposits from the fitting.
7. Reassemble sprayhead and reattach. Sprayhead only needs to be hand tightened.
Refer to Programming Manual on the Bunn-O-Matic website, at www.bunn.com for calibration routine to
verify sprayhead flow rate matches programmed flow rate. Machine may need to be re-calibrated due to
lime build up. If machine is cleaned and build up removed, machine must be re-calibrated to achieve desired
volumes.
Page 9
40885 080108