Bryant OM 17-101 Thermostat User Manual

Owner’s Manual
PROGRAMMABLE DIGITAL THERMOSTAT
53DFS250-SL-BRY
Cancels: New
OM 17-101
11/04
Front Panel
Su
:
AUTO
Am
Backlit LCD Display
COOL
HEAT
Su
:
AUTO
Warmer or + Button
Am
COOL
HEAT
Cooler or - Button
Override Button
Heat or Cool Indicator
Red = Heat, Green = Cool
•
•
•
•
•
•
•
•
•
•
7-Day Programmable
3 Occupied periods and 1 Unoccupied period
Auto Changeover
Large, Easy To Read Display
Thermoglow™ Backlight
Remote Sensor Ready
Dry Contact Equipped
Energy Saving Smart Fan
Fan Purge, IAQ Feature
Meets California Title 24
Su
ProgramOn
Pm
occupied 1
COOL
HEAT
MODE
Table of Contents
FRONT PANEL
DISPLAY
QUICK START Set the clock and go
BASIC OPERATION
PROGRAMMING Occupied and
Unoccupied Periods
ADVANCED SETUP
ABOUT ADVANCED FEATURES
AND OPERATION
WARRANTY
:
1
2
2
2
3
4
5
7
IMPORTANT: Follow Installation Instructions before
proceeding and set thermostat to mode “OFF” prior
to changing settings in setup or restoring factory
defaults.
FAN
HOLIDAY
PROGRAM
SET CLOCK
OVERR
Display
Quick Start Set the Clock and Go
1
6
2
1
9
8
10 7
:
Am ProgramOn Setup
Pm Stop Start
SuMTuWThFSa unoccupied 123
COOL
Override
HEAT
AUTO
OFFON
NOTE: During Setup and
Programming:
Pressing the Mode button
selects different flashing
items (represented in
black).
Pressing the Up and
Down buttons will modify
the flashing selection.
4
1
:
5
1
Pm
Locked
4
Fan
3
M
1 Mode Indicators
Selects the operation mode of the equipment.
COOL — indicates the air conditioning mode.
HEAT — indicates the heat mode.
AUTO — indicates the system will automatically
changeover between the heat and cool
modes as the temperature varies.
OFF — indicates the entire system is turned off.
PROGRAM ON —indicates the stored program is
enabled to run. See below.
2 Clock with Day of the Week
Indicates the current time and day. This clock is also
used to program the timer periods. See below.
3 Room Temperature Display
Indicates the current room temperature.
4 Desired Set Temperature
Indicates desired room temperature(s). See page 3.
5 Override Indication
Indicates the current program is currently being
overridden for up to 4 hours. See pages 3 and 5.
The thermostat is preprogrammed from the factory to operate equipment* without the need for further programming.
To optimize the installation of this thermostat follow the instructions in the Advanced Setup section.
*The thermostat is not preprogrammed from the factory to operate heat
pump systems. To control these systems, follow the steps in the
Advanced Setup section, page 4.
Basic Operation
Select Mode
6 Occupied or Unoccupied Indication
Indicates the program number: Occupied 1, 2, 3, or
Unoccupied. See pages 3 and 4.
7 Setup Indication
Indicates the thermostat is in the programming
mode. See page 4.
The HEAT setting indicates
the temperature the room has
to reach before the unit will
turn on to heat the room.
M
The COOL setting indicates
the temperature the room has
to reach before the unit will
turn on to cool the room.
M
8 Fan Operation Indication
Fan On Icon — indicates constant continuous fan
operation.
When Fan On Icon is not lit — indicates the fan will
only operate when necessary to heat or to cool.
AUTO will automatically
select heat or cool based on
room temperature demand.
9 Locked Indication
Locked appears after the right combination of
buttons are pressed, rendering the buttons
inoperative. See page 5.
Program On will activate the
stored timer operation.
(Occupied and Unoccupied
periods.)
:
Pm
HEAT
:
Pm
COOL
M
:
Pm
COOL
AUTO
10 Start/Stop Indication
Start or Stop appears when programming timer
functions. See page 3.
OFF indicates the system is
turned off.
:
Pm
:
Pm
ProgramOn
M
M
OFF
Page 2
HEAT
unoccupied
Basic Operation
unoccupied
Select Desired Temperature
Adjust the heating
set point for unoccupied
periods.
In any mode, adjust the
desired Set Point Temperature
with
COOL
HEAT
(35 to 99 F)
M
:
Pm
COOL
AUTO
HEAT
occupied 1
M
Select the day for
Occupied 1.
buttons.
Pressing the up/down buttons in Auto mode will adjust both the heat
and cool set point temperatures simultaneously.
Pressing the up/down buttons in Heat or Cool modes will adjust only
the heat or cool set point temperature.
Override
Su
:
ProgramOn
Pm
Stop
unoccupied
COOL
HEAT
:
:
Su
Pm
ProgramOn
occupied 1
COOL
Override
HEAT
Programming
:
Adjust the start time
for occupied 1.
During programmed, unoccupied
periods a press of the Override
button will force the thermostat into
Occupied 1 comfort settings,
temporarily.
With each successive push of the
Override button, the override timer
will add 30 minutes, until the maximum of 4 hours is reached. Then
the next press will zero out the override timer, returning to unoccupied if
there are no further button presses.
When in Override, the Override icon
and the Occupied 1 icon appear on
the display.
The time of day clock alternates with
the time remaining in override.
During Override, the set point temperatures are adjustable, provided
the keypad is not locked.
Am
Start
occupied 1
M
Adjust the stop time
for occupied 1.
M
:
Pm
occupied 1
occupied 1
M
Select Occupied 1 to run
on this day (On), or not to
run this day (Off).
Stop
ON
The copy command becomes available after the maximum number of occupied periods are programmed in a
day. This example uses 1 as the maximum occupied
periods ever programmed in one day.
Occupied and Unoccupied Periods
Tu
Select the maximum number
of occupied periods to be
used on any one day.
Typically 1.
occupied 1
Selecting Yes, then pressing mode will copy the previous day’s program and
then will ask the same copy question again. If yes is selected each time, this
routine will repeat until Saturday is copied to Sunday. After Saturday is
copied to Sunday, the copy command is unavailable.
(1,2 or 3)
Adjust the cooling
set point for occupied 1.
occupied 1
COOL
occupied 1
Tu
(35 to 99 F)
Adjust the heating
set point for occupied 1.
occupied 1
COOL
HEAT
(35 to 99 F)
Adjust the cooling
set point for unoccupied
periods.
:
Am
:
Pm
Start
occupied 1
Tu
unoccupied
COOL
(35 to 99 F)
Tu
Page 3
Stop
occupied 1
Programming
Setup
Select the cycles per
hour limit.
d=cycles per hour
limit defeated.
d1=d + defeat 5 min.
Compressor lockout.
Occupied and Unoccupied Periods
(d, d1, 2 - 6)
Setup
Yes
Locked
Setup
Selecting Yes, then pressing mode will copy the previous day’s program and
then will ask the same copy question again. If yes is selected each time, this
routine will repeat until Saturday is copied to Sunday. After Saturday is copied
to Sunday, the copy command is unavailable.
If no is selected, as in previous steps, flashing prompts for input will appear
for start and stop times for Occupied 1. If more than one occupied period was
selected in Step 1 on page 3, then cool/heat set point temperatures, and
start/stop times for additional occupied periods will be prompted.
Locked
(35 to 99 F)
Setup
PROGRAMMING NOTES
• If only 1 Occupied period is selected in step 1 on page 3, Occupied 2
and 3 programming steps are skipped. Further, if only 2 occupied
periods are selected, Occupied 3 programming steps are skipped.
• Heat and Cool set points for Occupied 1 are the same for every day
of the week. Heat and Cool set points for Occupied 2 and 3 can be
adjusted differently for each day of the week, if desired.
• If the start time is set later in the day than the stop time, the program will run from the start time to midnight and from midnight to the
stop time on the same day. For example: 9:00pm start, 8:00am stop,
on Monday. In this example the program will run from 12:00am Monday to 8:00am Monday and again from 9:00pm Monday to 12:00pm
Monday.
• The Unoccupied settings take effect at all times when: (1) the program is on and (2) the current time is outside a preset occupied
period. For this reason start and stop times are not necessary for
unoccupied.
• If the same start and stop times are programmed in for an occupied
period, then it will run 24 hours.
• If one occupied period starts and stops within another occupied
period the lower occupied number has priority. For example: If Occupied 3 is programmed to be “on” 24 hours, and Occupied 2 is programmed to run that day, then Occupied 2 settings will take over from
Occupied 3 between Occupied 2 start and stop times.
• To program Occupied 2 and Occupied 3 modes repeat programming
steps for Occupied 1.
Locked
(35 to 99 F)
Setup
Setup
ON
Advanced Setup
Steps 1 and 2 were performed on page 2. Advanced setup begins with
Step 3.
Press the Mode button.
While holding the Mode button,
press the Program button to
enter the Advanced Setup
screens.
On
NOTE: Each step number is located
at the top right corner of the
display for easy reference.
Setup
Unoccupied123
=
Press the Mode button. While holding the Mode button, press the Program button
leave the Setup screens. If no buttons are pressed, the display will leave the setup
screens after 30 seconds.
Select residential Heat
Pump, On or Off.
OFF
Off
Setup
Adjust the deadband
from 1 to 6 F.
(1 to 6 F)
Adjust the minimum
difference between
cooling and heating
set points.
Setup
(0 to 6 F)
Page 4
simultaneously press the Up and Down buttons. The
Locked icon will appear on the display.
Advanced Setup Table
STEP NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
DESCRIPTION
Time of day clock set
Day of the week
Heat Pump
Deadband or Temperature swing
Forced minimum difference
heat/cool
Cycles per hour
Security Levels
Maximum allowable Heat set point
Minimum allowable Cool set point
Fahrenheit or Celsius
Thermoglow™ backlight
Fan Purge timer
Soft Start
RANGE
24 hour
Su - Sa
Off / On
1-6F
FACTORY DEFAULT
12:00 Am
M
Off
2F
0-6F
2F
d, d1, 2 - 6
0-3
35 - 99 F
35 - 99 F
F/C
Off / On
0:00 - 3:00
0 - 99
6
0
80 F
65 F
F
On
0:00
0
• CLOCK BACKUP — In the event of a power loss, the
thermostat internal clock will continue to keep proper
time for a minimum of 48 hours without external power
or batteries.
• TWO-STAGE OPERATION — The Second Stage of
heat (Heat pump models only) is turned on when (1)
the first Stage has been on for a minimum of two minutes, and (2) the temperature spread from the set
point is equal to or greater than: the set point plus the
deadband, plus 2 degrees.
2 degrees 2 degrees
3rd Stage
High
2nd Stage
turn on
2nd Stage
Med
1st Stage Heat
turn on Set Point
1st Stage
Low
Dead
Band
To unlock the buttons, again press and hold the Mode
button. While holding the Mode button in, simultaneously press the Up and Down buttons in together.
The Locked icon will disappear from the display.
• DRY CONTACT SWITCH — The terminals are ‘normally open’. Closing or completing the circuit will
cause the thermostat to enter Occupied 1. This feature
allows an external device such as a Central Time
Clock, Occupancy Sensor, or a Telephone activated
device to force 1 or more thermostats into Occupied 1.
For the Dry Contact to work the thermostat must be in
Program On. Set Occupied 1 to Off for all 7 days, so
the Contact closure will be in control. When the thermostat is forced into Occupied 1 via the Dry Contact
closure, the icon Occupied 1 will blink.
CK1
GND
2 degrees 2 degrees
Cool
Set Point
Low
Med
unoccupied
ON
Cooling
Dead
Band
Program On
Pm
W
Locked
About Advanced Features and Operation
Heating
:
High
Fan Speeds
• MINIMUM HEAT/COOL SET POINT DIFFERENCE —
The Heat and Cool set points will not be allowed to
come any closer to each other than the value set in
Advanced Setup Step 5, on page 4. This minimum
difference is enforced during Auto changeover and
Program On operation.
• ENERGY SAVING SMART FAN — If Fan On is
selected, the fan will run continuously at all times,
except in Off, and will only run if there is a heating or
cooling demand in Unoccupied periods.
• OVERRIDE — As explained on page 3, pressing the
Override button during a programmed, Unoccupied
period will force the thermostat into Occupied 1, temporarily, up to 4 hours. If the Override button is
pressed during an Occupied period, the thermostat
will be forced into Unoccupied and the occupied number (1,2 or 3), it was forced out of will be turned off,
only for that day.
During Override periods the set points may be
adjusted, but they will not be remembered after Override ends.
• HEAT — First Stage = Heat Pump. Second Stage =
Heat Pump and Electric Heat.
• FAN PURGE TIMER — When this feature is activated,
the fan will turn on during Unoccupied at a preset
amount of time prior to Occupied 1. This preoccupancy fan purge timer may be set as instructed on
page 4, Step 12, from 0 to 3 hours. 0 = this feature
turned off.
• KEYPAD LOCK — To prevent unauthorized use of the
thermostat, the front panel buttons may be disabled.
To disable, or ‘lock’ the keypad, press and hold in the
Mode button. While holding the Mode button in,
• HOLIDAY MODE — This feature forces the thermostat
into Unoccupied for a preset duration, up to 99 days.
The Holiday setup display is entered as follows:
1
HOLIDAY
2
The thermostat will enter the Holiday mode when the
clock crosses midnight.
During Holiday mode Unoccupied set points are
enforced.
The Override button is active during Holiday mode. It
will override to Occupied 1 settings up to 4 hours then
return to Holiday mode. The Dry Contact Switch is
ignored.
The thermostat will exit Holiday mode at midnight of
the final programmed day. To terminate Holiday immediately, enter the Holiday setup screen and select 0.
• SOFT START — This feature is utilized in multiple
thermostat installations controlled by the Dry Contact
terminals. Assigning a unique Soft Start number to
each thermostat will stagger the turn on times, even
though the Dry Contact closes, for all the thermostats
connected, at the same time. Each Soft Start number
Page 5
represents a multiple of 30 seconds from the Dry Contact closure. For example, 1 = turn on 30 seconds after
Dry Contact closure, 2 = turn on 60 seconds after closure, 3 = turn on 90 seconds after closure, and so on.
See page 4, Step 13, to configure the thermostat for
Soft Start.
• DUAL SET POINT BEHAVIOR — The adjustable set
point range is: 35 to 99 degrees in Fahrenheit and 7 to
35 degrees in Celsius. When in the modes Heat or
Cool, this adjustable range is unhampered.
When adjusting any Auto mode, including programming Occupied and Unoccupied periods, the thermostat will not allow the Heat set point to get closer to the
Cool set point than the value programmed as the minimum difference in Step 5, page 4.
When entering the Auto mode from Cool, the Heat and
Cool set point temperatures will remain spread apart
by the amount that they were adjusted, prior to entering Auto.
For example: If the Cool set point was set to 80 while
in the Cool mode and the Heat set point was adjusted
to 70 while in the Heat mode, upon entering the Auto
mode the Heat and Cool set points would be 80 and
70. Both set points would then move up and down
together, (in this example spread by 10 degrees), by
pressing the up or down buttons.
To move the Heat and Cool set points closer together,
enter the Cool or Heat mode by pressing the Mode
button, then adjust the set point(s) closer together.
Heat is limited to how close it can come to Cool by
Step 5, page 4.
• REMOTE SENSORS (Optional Accessory) — When
connected to terminals RS+5, RS, and GND on the
back of the thermostat, the thermostat will read the
temperature from the Remote Sensor and ignore the
temperature sensor inside the thermostat. The thermostat automatically recognizes when a Remote Sensor
is connected. When reading the temperature from the
remote, the degree icon
above the room temperature blinks once a second.
The Override button on
the Remote Sensor works
slightly different than the
Override button on the
Optional
Remote Sensor
front panel. Each press of
Optional Sensor
the ‘External’ Override
button adds 2 hours to the
override timer. If the timer
was already active, the first button press will round the
runtime to either 2:00 or 4:00.
Subsequent button presses will not wraparound as the
Override button on the thermostat does, so the second
or greater button press will set the runtime to 4:00. The
Locked feature has no effect on the external Override
button. The wired Remote Sensor is connected to the
thermostat with up to 500 ft of 20 ga. or 300 ft of
18 ga. thermostat wire. See the Remote Sensor
instructions for further details.
• FACTORY DEFAULTS — Before restoring factory
defaults, set thermostat to OFF mode. If, for any reason it is desirable to return all stored settings back to
the factory default settings, press the Mode button.
While holding the Mode button in, press the Fan button
for 5 sec. All icons will appear. Press and hold in the
Fan button until Fd appears. This resets all factory settings. To calibrate room temperature, press the Up
and Down buttons at the same time twice. At this point
use the Up and Down buttons to calibrate room temperature, if needed. Press the Mode button to return to
normal operation.
Page 6
OVER
RIDE
OVER
RIDE
Warranty
One-Year Warranty — This Product is warranted to be free from defects in material and workmanship. If it appears within one year from the date of original installation, whether or not actual use begins on that date,
that the product does not meet this warranty, a new or remanufactured part, at the manufacturer’s sole option, to replace any defective part will be provided without charge for the part itself; PROVIDED the defective
part is returned to the distributor through a qualified servicing dealer.
THIS WARRANTY DOES NOT INCLUDE LABOR OR OTHER COSTS incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of either defective parts or replacement parts. Such costs may be covered by a separate warranty provided by the installer.
THIS WARRANTY APPLIES ONLY TO PRODUCTS IN THEIR ORIGINAL INSTALLATION LOCATION AND BECOMES VOID
UPON REINSTALLATION.
LIMITATIONS OF WARRANTIES — ALL IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES OF FITNESS FOR
A PARTICULAR PURPOSE AND MERCHANTABILITY) ARE HEREBY LIMITED IN DURATION TO THE PERIOD FOR WHICH
THE LIMITED WARRANTY IS GIVEN. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE MAY NOT APPLY TO YOU. THE EXPRESSED WARRANTIES MADE IN THIS
WARRANTY ARE EXCLUSIVE AND MANY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR,
DEALER, OR OTHER PERSON WHATSOEVER.
ALL WORK UNDER THE TERMS OF THIS WARRANTY SHALL BE PERFORMED DURING NORMAL WORKING HOURS.
ALL REPLACEMENT PARTS, WHETHER NEW OR REMANUFACTURED, ASSUME AS THEIR WARRANTY
PERIOD ONLY THE REMAINING TIME PERIOD OF THIS WARRANTY.
THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR:
1. Normal maintenance as outlined in the installation and servicing instructions or owners manual including filter cleaning and/or replacement and
lubrication.
2. Damage or repairs required as a consequence of faulty installation, misapplication, abuse, improper servicing, unauthorized alteration or improper operation.
3. Failure to start due to voltage conditions, blown fuses, open circuit breakers or other damages due to the
inadequacy or interruption of electrical service.
4. Damage as a result of floods, winds, fires, lightning, accidents, corrosive environments or
other conditions beyond the control of the
Manufacturer.
5. Parts not supplied or designated by the Manufacturer, or damages resulting from their use.
6. Manufacturer products installed outside the continental U.S.A., Alaska, Hawaii, and Canada.
7. Electricity or fuel costs or increases in electricity or fuel costs from any reason whatsoever including additional or unusual use of supplemental electric heat.
8. ANY SPECIAL INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE
WHATSOEVER. Some states do not allow the exclusion of incidental or consequential damages, so the
above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to
state.
Page 7
Copyright 2004 Bryant Heating & Cooling Systems
Printed in U.S.A.
CATALOG NO. 5353-003