Buhler 2500 Automobile Accessories User Manual

inland
Model 2500
For serial number 08BM2500001 and later
Operator’s and Parts Manual
Bale Carrier
P4186
04/08
INLAND WARRANTY POLICY
Buhler Manufacturing products are warranted for a period of twelve (12) months (90 days for commercial
application) from original date of purchase, by original purchaser, to be free from defects in material and
workmanship under correct, normal agricultural use and proper applications.
Buhler Manufacturing’s obligations under this warranty shall be limited to the repair or exchange, at Buhler
Manufacturing’s option, of any Buhler Manufacturing product or part which proves to be defective as provided.
Buhler Manufacturing reserves the right to either inspect the product at the buyer’s location or have it returned to the
factory for inspection.
The above warranty does not extend to goods damaged or subject to accident, abuse or misuse after shipment from
Buhler Manufacturing’s factory, nor to goods altered or repaired by anyone other than an authorized Buhler
Manufacturing representative.
Buhler Manufacturing makes no Express Warranties other than those, which are specifically described. Any
description of goods, including any references and specifications in catalogues, circulars and other written material
published, is for the sole purpose of identifying goods and shall conform to such descriptions. Any sample or model
is for illustrative purposes only and does not create an Express Warranty that the goods conform to sample or model
shown.
The purchaser is solely responsible for determining suitability of goods sold. This warranty is expressly in lieu of
all other warranties expressed or implied. Buhler Manufacturing will in no event be liable for any incidental or
consequential damages whatsoever. Nor for any sum in excess of the price received for the goods for which liability
is claimed.
WARRANTY CLAIMS:
Warranty requests must be prepared on Buhler Manufacturing Warranty Claim Forms with all requested information
properly completed. Warranty Claims must be submitted within a thirty (30) day period from date of failure repair.
WARRANTY LABOR:
Any labor subject to warranty must be authorized by Buhler Manufacturing. The labor rate for replacing defective
parts, where applicable, will be credited at 100% of the dealers posted shop rate. Defective parts will receive an
extra 10% discount to assist with freight or other incidental costs.
GOVERNMENT LEGISLATION:
Warranty terms and conditions are subject to Provincial or State legislation.
IMPORTANT FACTS:
Buckets and Bucket Tines Carry No Warranty
Bent Spears Carry No Warranty
Snowblower Fan Shafts Carry No Warranty
Mower Blades Carry No Warranty
Portable Auger Parts Have Two (2) Year Warranty
Printed in U.S.A.
bühler
2500 Bale Carrier
OPERATORS AND PARTS MANUAL
Table of Contents
Description
TERMINOLOGY AND DECAL LOCATIONS ILLUSTRATIONS……..………...
GENERAL SPECIFICATIONS…..…………………………………………………
INTRODUCTION…………………………………………………………………….
Serial Decal Location…………………………………………………………….
Warranty Registration…………………………………………………………….
SAFETY………………………………………………………………………………
General Safety Notes…………………………………………………………….
Safety Decals……………………………………………………………………..
Important Precautions……………………………………………………………
PRE OPERATION CHECKLIST...…………………………………………………
OPERATION.………………………………………………………………………..
Attaching Bale Carrier to Tractor………………………………………………..
Attaching Bale Carrier Controls to Tractor……………………………………..
Carrier Controls Operation………………………………………………………
Loading Bales……………………………………………………………………..
Bale Pusher Operation…………………………………………………………...
Transporting 2500 Bale Carrier…………………………………………………
Unloading……..…………………………………………………………………..
LUBRICATION.………………………………………………………………………
Pivot Points………………………………………………………………………..
Roller Chain……………………………………………………………………….
Carrier Beams…………………………………………………………………….
MAINTENANCE…………………………………………………………………….
Fasteners………………………………………………………………………….
Hydraulic System…………………………………………………………………
Hydraulic Fitting Torques………………………………………………………..
Chain……………………………………………………………………………….
Wheels/Tires………………………………………………………………………
Storage…………………………………………………………………………….
APPENDIX LIST……………………………………………………………………..
APPENDIX A ASSEMBLY INSTRUCTIONS…………………………………….
APPENDIX B HYDRAULIC ASSEMBLY………………………………………...
APPENDIX C ELECTRICAL ASSEMBLY………………………………………...
APPENDIX D GENERAL ASSEMBLY…………………………………………...
CHECKLIST………………………………………………….………………………
Predelivery………………………………………………………………………...
Customer Delivery………………………………………………………………..
1
Page
2
3
4
4
4
5
5
7
8
9
10
10
10
12
12
14
14
15
16
16
16
16
17
17
18
18
19
19
20
21
22
26
51
55
79
79
79
2
13. Part # 814490
12
7
YELLOW 16
2500 13
13. Part # 814458
Note: 1) Refer to page 8 for detailed
information on safety decals
2) Awarness signs are shown on right side
only for clarification. Signs are provided on
both left and right sides except for numbers 9
and 14 which are only on the position
indicated.
YELLOW 16
AMBER
18
REFLECTOR
YELLOW 16
RED 15
ORANGE
FLOURESCENT 17
Slow Moving
Vehicle
BACK
RIGHT SIDE
4
11
10
YELLOW 16
Center Bale Stop
Carrier Beam
2
1
Front Crossmember
6
5
Bale Lift Arm
Pusher
Second Crossmember
16
YELLOW
SIDE
END
8
LEFT SIDE
14
FRONT
Clevis
9
Valve Bank
Jack
Front Stop
Bale Fork
bühler
2500 Bale Carrier
TERMINOLOGY AND DECAL LOCATIONS ILLUSTRATION
bühler
2500 Bale Carrier
GENERAL SPECIFICATIONS:
Dimensions:
- Length: 45’ (13.7 m)
- Deck Length: 37’ (11.3 m)
- Width: 12’ 9” (3.9 m)
- Weight (empty): 9,587 LB (4349 kg)
- Drawbar Vertical Load (empty): 2395 LBF (10653 N)
- GVW: 37440 LB (16983 kg)
Capacity:
- Total bale payload: 28065 LB (12731 kg)
- Bales up to 6’ (1.8 m) diameter maximum to 4’ (1.2 m) diameter minimum
- Hay crop, small grains, and flax straw
- Sixteen 4’ (1.2 m) wide bales
- Fourteen 5’ (1.52 m) wide bales
Tires:
- 8-12.5L x 15 FI - 12 ply, Load Range F, Farm Hwy Service tire
- Six bolt heavy duty hubs with twine guards
- Walking beam axle design
Control Handle:
- Power: 12v
- Fuse: 15 amp (surge protection provided on machine)
Hydraulics:
- Two remote tractor hydraulics circuits required for operation
- Closed-center hydraulic standard.
- In-field configuration is required for open-center or load-sensing tractors
- Two lift cylinders with restrictor
- Two tilt cylinders with restrictor
- Four 22.2 cu. inch (363.79 cu cm) hydraulic motors
- See Appendix B for details on hydraulic components
Tractor:
- Size: 100 hp (75kW) recommended
- Weight: As per ASAE specification ASAE S365.4 the tractor must weight 25000 LB
(11340 kg) to adequately handle a GVW of 37440 LB (16983 kg)
- Maximum loaded towing speed 20 mph (32 km/h)
3
bühler
2500 Bale Carrier
INTRODUCTION
CAUTION:
Your 2500 Bale Carrier requires a recommended minimum 100 hp
(75kw) tractor. The maximum loaded transportation speed of 20 mph (32 km/h) and
37440 LB (16983 kg) must not be exceeded.
This manual has been provided as information regarding the specifications, safe
operation and maintenance of your agricultural 2500 Bale Carrier. Read and understand
this manual and the tractor manual prior to operating to obtain the best use of operating
your 2500 Bale Carrier. Keep this manual for reference and to forward to new operators
and owners. Contact your local Buhler Inland dealer if you require any assistance,
information or additional manuals.
Your new bale carrier is designed to retrieve, transport, and unload a wide range of
round bales. Sizes that can be accommodated range from 4’ (1.2 m) diameter to 6’ (1.8
m) diameter in a variety of hay crops as well as small grain and flax straw.
Serial Decal Location
The serial decal is located on the left side of the front crossmember. Please record the
serial number in the space provided for future reference. The serial decal will provide
the model and date of manufacture of the Bale Carrier and will be required to obtain
correct replacement parts and complete warranty claims.
For your records, record
Serial Number here:_________________________
B.I.I. FARGO INC.
FARGO NORTH DAKOTA
versatile
farm king
allied
inland
Warranty Registration
The warranty registration and delivery report MUST be completed within thirty (30) days
of delivery to validate the warranty.
4
bühler
2500 Bale Carrier
SAFETY
Read and understand all the safety messages listed in this manual. For your safety and
the safety of others near the machine, learn how to control and operate your 2500 Bale
Carrier properly. It is your responsibility to inform subsequent operators and owners of
these precautions.
General Safety Notes
Keep young children away from machinery and bales at all times.
Be aware that accidents often happen when the operator is tired or in a hurry to get
finished. Take the time to consider the safest way. Never ignore warning signs of
fatigue.
Keep hands, feet, clothing and hair away from moving
parts. Never attempt to clear obstructions or objects
from a machine while the engine is running.
Keep all shields in place. Never alter or remove safety
equipment.
Do not attempt to clear any blockage or reach into the 2500 Bale Carrier with your
arm or leg unless the tractor engine is stopped.
Do not load bales of sizes not out lined in the specifications section
Use proper lighting and safety warnings when transporting equipment on public
roads and during darkness. The slow moving vehicle emblem must be visible. Check
with your local law enforcement agency for specific requirements.
Provide a first-aid kit for use in case of
emergencies.
The safety information in this manual does
not replace safety codes, insurance needs, or
laws governing your area. Be sure your machine
meets the standards set by these regulations.
Keep a fire extinguisher with the machine.
be sure the extinguisher is properly maintained
and be familiar with its proper use.
Wear close-fitting clothing and cover long hair. Never wear
dangling items such as scarves or bracelets.
Remember that YOU are the key to safety. Good safety
practices protect you and the people around you.
Follow all safety messages in the manual and on safety
signs located on the machine.
It is your responsibility to read and understand this manual
completely before operating the bale carrier.
5
bühler
2500 Bale Carrier
Never leave the tractor unattended while the 2500 Bale Carrier is hooked up, always
shut tractor off and remove key before leaving the tractor seat. A child or even a pet
could engage an idling machine.
Keep the 2500 Bale Carrier on solid ground, rocks and holes can be dangerous for
operation and movement.
Prior to use, check to ensure the attachment is properly hitched.
Improper use of the 2500 Bale Carrier and tractor can cause serious injury or death.
Never operate 2500 Bale Carrier with frayed or damaged hoses or leaking fittings. A
burst could cause one or more hydraulic components to behave erratically causing
serious injury or loss of life.
Operate 2500 Bale Carrier only while seated in the tractor seat.
Do not load bales improperly, always load according to the manual’s operation
procedures.
If for some reason you feel the tractor tipping immediately lower lift arms.
Do not raise lift arms to extreme heights while tractor is on an incline. Be alert for
terrain changes and adjust accordingly.
Allow for 2500 Bale Carrier and tractor length when turning.
Do not overload the GVW of 37 440 LB (16983 kg) and when loaded keep the speed
below 20 mph (32 km/h).
Before allowing anyone to operate the machine, for however a short time or
distance, make sure they have been instructed in its safe and proper use.
Review the manual and all safety related items with all operators annually.
correct other operators not using recommended procedures before an accident
occurs.
When assembling, operating and servicing machinery, wear all the protective
clothing and personal safety devices that could be necessary for the job at hand.
Never work beneath a raised lift arm unless it is securely supported. The control
handle can be moved or a hydraulic leak could cause the arm to drop resulting in
serious injury or death.
Use only service and repair parts made or approved by the equipment manufacturer.
substituted parts may not meet strength, design, or safety requirements.
Do not modify the machine. Unauthorized modifications may impair the function
and/or safety and affect machine life.
Keep the area used for servicing machinery clean and dry. Wet
or oily floors are slippery. Wet spots can be dangerous when
working with electrical equipment. Be sure all electrical outlets
and tools are properly grounded.
Keep machinery clean. Straw and chaff on hot surfaces are a fire hazard. Do not
allow oil or grease to accumulate on service platforms, ladders or controls. Clean
machines before storage.
Never use gasoline, naphtha or any volatile material for cleaning purposes. These
materials may be toxic and/or flammable.
When storing machinery, cover sharp or extending components to prevent injury
from accidental contact.
6
bühler
2500 Bale Carrier
Safety Decals
The Terminology And Decal Location Illustration shows the approximate location and
detail of safety decals. To install safety decals ensure the installation area is clean and
dry. Decide on the exact position before you remove the backing paper. Remove the
smallest portion of the split backing paper and align over the specified area. Carefully
press in place. Slowly peel back the remaining paper and smooth the remaining portion
in place. Small air pockets can be pierced with a pin and smoothed out. Keep all decals
clean and replace any that are damaged or missing. Replacement decals are available
from you local dealer. The following pictorials indicate important precautions to be used
during the operation of the 2500 Bale Carrier.
1. Part # 813624
5. Part # 813627
2. Part # 813625
3. Part # 21867 4. Part # 813626
6. Part # 813632
7. Part # 813633
8. Part # 813635
WARNING
HIGH-PRESSURE FLUID HAZARD
To prevent serious injury or death:
Relieve pressure on system
before repairing or adjusting or disconnecting.
Wear proper hand and eye protection
when searching for leaks. Use wood or
cardboard instead of hands.
Keep all components in good repair.
10. Part # 813637
SW700
11. Part # 813636
12. Part # 814490
19. Part # A7017-00
13. Part # 814458
2500
14. Part # 813952
BUHLER BALE CARRIER 1500/2500 SNUBBER UNIT
P/N: 813949
(NO SERVICEABLE PARTS INSIDE)
DECAL PN: 813952
CONTINUITY LIGHT
15. Part # 967053
RED REFLECTIVE
16. Part # 967055
YELLOW REFLECTIVE
7
17. Part # 813631
ORANGE FLUORESCENT
18. Part # 813628
AMBER REFLECTIVE
bühler
2500 Bale Carrier
Important Precautions
The alert symbol is used throughout this manual. It indicates attention is required and
identifies hazards and alerts you that your safety is involved. Follow the recommended
precautions.
CAUTION
Indicates a potentially hazardous situation, which may result in
injury. It may also be used to alert against unsafe practices.
WARNING
The warning symbol indicates a potentially hazardous
situation, which could result in death or serious injury and includes hazards that are
exposed when guards are removed. It may also be used to alert against unsafe
practices.
DANGER
The danger symbol indicates an imminently hazardous
situation, which will result in death or serious injury. This signal word is limited to the
most extreme situations, typically for machine components, which for functional
purposes, cannot be guarded
8
bühler
2500 Bale Carrier
PRE-OPERATION CHECKLIST
CAUTION
Make sure the tractor has a 100 hp (75 kw) or greater rating
and a mass of 25000 LB (11340 kg). Make sure the drawbar is capable of supporting
the 2500 Bale Carrier empty or loaded.
WARNING
The tractor must be equipped with an approved Roll over
Protection Structure (ROPS) and safety belts to help prevent personal injury or death
caused by tractor roll over.
To ensure safe and proper operation of the 2500 Bale Carrier, inspect the following
items prior to operation and daily thereafter. Refer to operation, lubrication and
maintenance sections for detailed instructions.
Prior to first use verify that the 2500 Bale Carrier has been properly assembled and
that the operator understands the safety, operating, and maintenance requirements.
Check for missing fasteners and replace if necessary. Refer to maintenance section
for details.
Check and maintain proper tire pressure of 90 psi (620 kpa).
Check for loose wheel bolts. Bolts must be torqued to 125 ft LB (170 Nm).
Clean 2500 Bale Carrier of any foreign material that may have accumulated from
previous run.
Lubricate all points requiring daily lubrication.
Check chain tension and adjust if necessary with front sprocket adjusting bolt
(approximately 6” (15 cm) of upward slack). This is verified by raising the chain by
hand.
Ensure top surface of bale carrier beams are properly coated with a graphite coating
to reduce bale friction while pushing bales back.
Ensure that the tractor used to pull the 2500 Bale Carrier is in working order
according to the tractor manual.
Verify the 2500 Bale Carrier is properly coupled to the tractor with the safety chain.
Inspect all safety reflective decals, slow moving vehicle decals and lights where
applicable.
Inspect the hydraulic system on the 2500 Bale Carrier and your tractor for leaks or
any other damage.
Ensure the control handle actions reflect the movements of the 2500 Bale Carrier.
Inspect all electrical connections to ensure proper function of the machine
Ensure transport safety chain is disengaged from bale lift arm and stored on chain
lug located on second cross member. Failure to do so may cause damage to lift arm.
.
9
bühler
2500 Bale Carrier
OPERATION
CAUTION
Prior to operation ensure the operator has read and
understands the safety requirements of the 2500 Bale Carrier. Ensure the pre-operation
checks have been completed prior to operation.
1. Attaching Bale Carrier To Tractor
CAUTION
Shut off tractor, engage parking brake and remove key before
working around 2500 Bale Carrier. Refer to tractor manual for tractor parking
procedures.
CAUTION
Use only the drawbar to couple the 2500 Bale Carrier to the
tractor. Ensure drawbar is capable of handling the 2500 Bale Carrier load. The tractor
must have a minimum mass of 25000 LB (11340 kg) and recommended 100 hp (75 kw).
Using the tongue jack, raise tongue to align with hitch pin, adjust clevis position
as necessary to level the carrier beams.
Position tractor and secure with locking type drawbar pin (not supplied). Use an
approved hitch pin with a mechanical retainer.
Route safety chain around the hitch clevis, around drawbar support and back
hook. Refer to tractor manual for further drawbar instructions.
Do not use intermediate support on drawbar as attaching point.
Store safety chain off the ground when not in use. If safety chain is damaged in
any way, contact your dealer for a replacement.
For serial number 08BM2500001 and later, open-center valve is a factoryinstalled feature
Note: The bale carrier is factory-configured to operate with tractors
having CLOSED-CENTER hydraulic systems (page 27).
For tractors with OPEN-CENTER or LOAD-SENSING hydraulic systems,
refer to the configuration on pages (29, 46 and 47).
2. Attaching Bale Carrier Controls To Tractor
Bale raise and push functions are controlled by the 2500 Bale Carrier valve.
Pressure and tank are supplied by two hoses complete with black hydraulic tip
covers. The retract hose is designated with a check valve and ensures proper
flow through the valve. Connect tank hose to retract circuit and extend hose to
opposite extend port see Appendix B for schematic.
The tilt function is controlled by the tractor’s remote valve. Extension and
retraction are supplied by two hoses complete with red hydraulic tip covers.
Connect control handle harness to the machine harness. Connection is made at
the snubber unit by matching the appropriate socket and plug.
10
bühler
2500 Hayliner
The power required to operate the 2500 Bale Carrier is supplied by the tractors
12-volt electrical system. Connect the red wire to the tractor positive and green to
tractor ground. Connection may be made via tractor accessory plug or alternate
method. The 15 amp fuse must be used on the positive wire as supplied.
Verify 2500 Bale Carrier operation matches 2500 Bale Carrier control handle
decal.
11
bühler
2500 Hayliner
3. Carrier Control Operation
To begin 2500 Bale Carrier operation engage the remote hydraulic valve in the
extension position. Lock valve in detent. Valve to remain constantly on during
operation.
The control handle is fitted with one (1) rocker switch and four (4) momentary
contact rocker switches. They function as follows:
o PUSHER SPEED: Select
(HIGH) to operate
pusher motors in series at high speed or
(LOW) to operate in parallel at low speed. Torque
is increased at low speed and pushes bales with
more force.
o RH PUSHER: Depress and hold RH PUSHER
FWD to move right forward. Depress and hold RH
PUSHER BACK to move right pusher back.
o LH PUSHER: Depress and hold LH PUSHER
FWD to move left pusher forward. Depress and
hold LH PUSHER BACK to
move left pusher
back.
o RH LIFT ARM: Depress and hold RH LIFT ARM
UP to raise right lift arm. Depress and hold RH
LIFT ARM DN to lower right lift arm.
o LH LIFT ARM: Depress and hold LH LIFT ARM
CONTROL
UP to raise left lift arm. Depress and hold LH LIFT
HANDLE
ARM DN to lower left lift arm.
PUSHER
SPEED
LH PUSHER FWD
RH PUSHER FWD
LH PUSHER BACK
RH PUSHER BACK
LH LIFT ARM UP
RH LIFT ARM UP
LH LIFT ARM DN
RH LIFT ARM DN
To operate raise / lower tilt function engage the remote hydraulic valve in the
extension position to raise the tilt deck and engage the retract position to lower
the deck.
4. Loading Bales
WARNING
Make sure area is clear before lowering bale lift arms. Failure
to do so could result in injury or death.
The right bale lift arm is used to load bales onto the right side of the carrier while
the left bale lift arm is used to load bales onto the left side of the carrier.
Align the tractor and 2500 Bale Carrier as indicated in the pictoral for pick up
method used. Slowly approach the bale at 5 mph (8 km/h) while loading. When
bale is properly captured begin to raise the bale.
To balance the 2500 Bale Carrier, alternate bale picking sides.
The 2500 Bale Carrier is designed to load bales with one of three options. Refer
to the appropriate section on the next page for your option loading instructions.
Instructions for the fork positions are provided in appendix A.
NOTE:
Before loading bale the pusher must be at the front of the carrier deck.
12
bühler
2500 Hayliner
The Fixed Pick Up Arm requires the
operator to drive at 90° to the baling direction.
The bales are loaded “End On”. The bale is
loaded onto the carrier deck by depressing
and holding LH or RH LIFT ARM UP until the
bale rolls off the pickup arm and onto the
carrier beams.
FIXED PICK UP ARM
The Bale Deflector attached to the fixed pick
up arm allows the bales to be picked up from
either “End On” or “Side On.” The deflector
rotates the bale 90° before it is lifted up onto
the carrier. Forward travel is used to rotate
the bale. Approach the bale so that the outer
end of the bale rides up on the bale deflector
as the loading arm moves under the bale.
BALE DEFLECTOR
To pickup bales that are placed “End On,”
drive so the inner arm of the loading fork is
against the inner edge the bale. The bale will
then be loaded onto the carrier in the same
direction as it was picked up. Continue to
load using fixed arm instrucitons.
NOTE:
The bale should be contacted about 12” (30 cm) from its outer end when
using the bale deflector. Contacting the bale further to the inside may result in damage
to the deflector, bale lift arm or bale.
The Rotating Pick Up Arm (RPU) loads
bales “side on”. The lift arm starts in the
lowered position. Drive forward until the forks
are positioned around the ends of the bale
with the inside stationary fork as close as
possible to the bale. Depress and hold LH or
RH LIFT ARM UP. The bale is then squeezed
on end until the pressure matches the
sequence valve setting that rotates and
raises the bale.
When the bale is raised above the beam
release by depressing LH or RH arm down.
This releases the bale and returns the RPU
to the ready state for the next bale. Refer to
the assembly instructions for adjusting RPU’s
settings.
13
RPU LOADING BALE
RPU RAISING BALE
bühler
2500 Bale Carrier
5. Bale Pusher Operation
CAUTION
To avoid misbalanced loads the operator is only required to
push back one bale length to prepare for the next bale.
NOTE: Lower loading arm before operating the pusher.
Depress and hold LH or RH PUSHER BACK and move bales far enough to the
rear to provide room to load the next bale.
Return pusher all the way to the front by depressing and holding LH or RH
PUSHER FWD.
Hi speed / Low torque mode is recommended for normal use.
Low speed / High torque mode is for heavier payloads or situations where bales
are wet or resist sliding.
6. Transporting 2500 Bale Carrier
WARNING
Do not tow over 20 mph (32 km/h) when loaded. Turn on
flashing lights when transporting on public roadways. Obey local regulations regarding
road transport. Raise bale lift arm and use the safety chain when transporting. Ensure
the lift arm chain latch is used to prevent the safety chain from dislodging or loosening.
Do not transport if end bale is overhanging
beams. Beam should extend beyond last bale
for a minimum of 2’ (61 cm).
Raise left and right lift arms prior to transport.
Always engage lift arm safety chains when
transporting on public roadways or when not
in field. Lock chain in position with latch
provided.
Monitor the condition and position of bales
that are being transported.
Slow speed when transporting over bumps or
rough terrain.
14
LATCH
SAFETY CHAIN
LIFT ARM
LIFT ARM SAFETY CHAIN
ILLUSTRATION
bühler
2500 Bale Carrier
7. Unloading
DANGER
Make sure area is clear before unloading. Failure to do so
could result in serious injury or death.
NOTE:
Left or right decks can be unloaded individually or together. However, the
pusher moves faster and has more torque when operated individually. Do not run
pushers all the way to the end, the resulting shock load may cause damage to chain
and drive.
Extend tilt cylinder to raise carrier beams by engaging the tractor’s extension
hydraulics.
Depress and hold LH and/or RH PUSHER BACK switch to push the bales off the
carrier beam.
Once the rear bale has been pushed off the carrier, slowly drive forward while
pushing the bales back (unloading) to keep all bale ends in contact.
When amber reflector on inside of the carrier
beam becomes visible stop the pusher. The
reflector is approximately 26” (66cm) from the
end of the beam.
Slowly drive forward to unload the last bale.
Retract the tilt cylinder to lower the beam and
begin the next loading cycle.
AMBER REFLECTOR
Return PUSHER to the front of the 2500
LOCATION
Bale Carrier to prepare for the next cycle.
15
bühler
2500 Bale Carrier
LUBRICATION
CAUTION
Place all controls in neutral, stop engine, set parking brake
and remove ignition key before inspecting, servicing, adjusting or repairing the 2500
Bale Carrier.
CAUTION
Ensure the 2500 Bale Carrier tires and hitch are securely
block. Otherwise, verify the 2500 Bale Carrier is properly coupled to the drawbar on a
tractor with a minimum mass of 25000 LB (11340 kg).
Pivot Points
Lubricate 2500 Bale Carrier bushings and pivots every eight hours of average
operation with high-grade grease at all fitting locations. Select grease based on
the expected outside temperature range. Lithium, Molybdenum and synthetic
greases are preferred. Use the tractor hour meter as a guide. Increase lubrication
intervals for extreme use or adverse conditions. Each pivot should be lubricated
until grease is visible at pin. The fixed arm carrier has 16 lubrication points and
the RPU carrier has 18 points. Refer to the illustrations below for locations.
AXLE BEARING
HYDR AULIC C YLINDER END
RPU PIVOT LEFT
AND RIGHT SIDES
BUSHING
HYD RAULIC C YLINDER
END
BUSHING
AXLE BEARIN G
RPU LUBRICATION
ILLUSTRATION
H YD RAULIC CYLIN DER END
LUBRICATION ILLUSTRATION
Roller Chain
Manually brush an SAE lubricant while chain is stationary.
Lubricate the chains every time bolt torque maintenance is performed.
Carrier Beams
Apply a graphite coating such as Slip PlateTM to the carrier beams as required to
ensure a smooth push back operation.
Follow application instructions as provided by the coating manufacturer.
At the end of the season apply a coating to prevent rust on the carrier beams.
16
bühler
2500 Bale Carrier
MAINTENANCE
CAUTION
Place all controls in neutral, stop engine, set parking brake,
remove ignition key and wait for all moving parts to stop before servicing, adjusting or
repairing the 2500 Bale Carrier.
CAUTION
Ensure the 2500 Bale Carrier tires and hitch are securely
block. Otherwise, verify the 2500 Bale Carrier is properly coupled to the drawbar on a
tractor with a minimum mass of 25000 LB (11340 kg).
NOTE:
Service intervals should be increased when operating in extreme or difficult
conditions.
1. Fasteners
Inspect all bolt torques after first use and 50 hours thereafter.
Periodically inspect for broken or missing fasteners. Replace with fasteners of
similar size and equivalent grade.
The table below lists the correct torque values for various bolts and cap screws
used on the bale carrier. Tighten all bolts to specified values unless otherwise
noted.
BOLT TORQUE
SAE 5
BOLT
DIAMETER
"A"
lb-ft
N.m
lb-ft
N.m
lb-ft
N.m
1/4"
6
8
9
12
12
17
5/16"
10
13
19
25
27
36
3/8"
20
27
33
45
45
63
7/16"
30
41
53
72
75
100
SAE 2
SAE 8
1/2"
45
61
80
110
115
155
9/16"
70
95
115
155
165
220
5/8"
95
123
160
215
220
298
3/4"
155
225
290
390
400
540
7/8"
170
230
420
570
650
880
1"
225
305
630
850
970
lb-ft
125
33
1320
LOCATION
WHEEL HUB BOLTS
ALL CARRIAGE BOLTS
N.m
170
45
17
bühler
2500 Bale Carrier
2. Hydraulic System
WARNING
Escaping fluid under pressure can have sufficient force to
penetrate the skin, causing serious personal injury. Before repairing, adjusting, or
disconnecting lines, be sure to relieve all pressure.
WARNING
Never operate the 2500 Bale Carrier with frayed or damaged
hoses or leaking fittings. A burst would cause the lift arm to drop suddenly and result in
serious injury or death and cause damage to the loader or tractor.
Before applying pressure to the system, be sure all
connections are tight and the lines, pipes, and hoses are
not damaged.
Wear proper hand and eye protection when searching for
leaks. Use a piece of wood or cardboard instead of hand
to check for leaks.
Maintain all components in good working order.
If injured by escaping fluid, see a doctor at once. Serious
infection or toxic reaction can develop if proper medical
treatment is not administered immediately.
Regularly check the fluid level in the tractor reservoir and
follow the maintenance procedures in the tractor
Operator’s Manual.
Regularly inspect cylinders, hoses and fittings for leaks,
crimps and abrasions or other signs of wear and tear or
impending failure.
Ensure hoses do not bind or stretch during operation.
Always keep hoses tied or supported to prevent rubbing against sharp areas or
being pinched. We suggest using tie wraps to support hoses.
Replacement hoses must have a working pressure of 3000 psi (20685 kpa) or
higher.
3. Hydraulic Fitting Torques
Dash Size
Thread
Size
-04
-05
-06
-08
-10
-12
-14
-16
-20
-24
7/16-20
1/2-20
9/16-18
3/4-16
7/8-14
1-1/16-12
1-3/16-12
1-5/16-12
1-5/8-12
1-7/8-12
Jam Nut or Straight
ORB Fitting Torque
(ft-lbs)
(NM)
14-16
20-22
18-20
24-27
24-26
33-35
50-60
68-78
72-80
98-110
125-135
170-183
160-180
215-245
200-220
270-300
210-280
285-380
270-360
370-490
SAE 37° (JIC)
Swivel Nut Torque
(ft-lbs)
(NM)
10-11
13-15
13-15
18-20
17-19
23-26
34-38
47-52
50-56
69-76
70-78
96-106
80-90
110-122
94-104
127-141
124-138
169-188
156-173
212-235
18
bühler
2500 Bale Carrier
4. Chains
Check for proper chain tension and sprocket
alignment after first use and every 50 hours
thereafter.
Turn the front sprocket adjusting bolt
clockwise until there is approximately 6” (15
cm) of upward slack in the chain at the center
of the track. Clockwise increases tension and
counter clockwise reduces tension.
Proper chain tension may be verified by
raising the chain by hand.
See
lubrication
section
for
further
maintenance instructions.
FRONT ADJUSTING
BOLT
5. Wheels / Tires
Inspect hub bolts after first use and 50 hrs thereafter. Hub bolts must be torqued
to 125 ft-lb (170 Nm).
Thread-locking compound such as Locktite 242 is recommended for the hub
bolts.
Ensure that dust caps are firmly in place.
Check tire pressure regularly: 90 psi (620 kpa).
The wheel bearings should be inspected and re-packed annually with a SAE
multi purpose type grease. If hub is supplied with grease fitting, grease every
500hrs.
Air valve should face away from the hub.
19
bühler
2500 Bale Carrier
6. Storage
CAUTION
Place all controls in neutral, stop engine, set parking brake
and remove ignition key before inspecting, servicing, adjusting or repairing the 2500
Bale Carrier.
CAUTION
Ensure the 2500 Bale Carrier tires and hitch are securely
block. Otherwise, verify the 2500 Bale Carrier is properly coupled to the drawbar on a
tractor with a minimum of 25000 LB (11340 kg).
Start of Season
Clean and inspect the bale carrier when taking it out of storage. Ensuring that the
bale carrier is in optimum condition at the start of the season reduces the
chances of a costly breakdown during the season.
Clean and inspect chains and chain rollers for excessive wear or stiffness. Check
for proper adjustment and alignment.
Lubricate entire bale carrier. Ensure that all grease fittings are in place and taking
grease properly.
Operate the bale carrier for a short time. Check that all moving parts are
operating freely. Check for hydraulic leaks.
Inspect and repack wheel bearings with a SAE multi purpose type grease.
Replace and secure safety shields. Review safety regulations.
Check all bolts for tightness. Replace lost or worn bolts.
Check that tires are properly inflated.
Review the Operator’s Manual.
During The Season
At the end of each day of operation park the bale carrier in a clean, dry, sheltered
area.
Lubricate areas requiring daily lubrication.
Remove any build up of hay or straw.
End Of Season
Replace worn or damaged parts and replace if necessary. To avoid costly delays
contact your dealer for replacement parts before the start of the next season.
Store the bale carrier in a clean, dry, sheltered area.
Replace all missing or broken bolts with bolts of similar size and grade.
Clean the baler carrier thoroughly. Dirt draws moisture that rusts metal.
Repaint chipped or worn areas. Paint is available from your dealer.
Clean chains and brush with SAE light machine oil (or equivalent) to prevent rust.
Repaint the top of the carrier beams with a graphite paint such as Slip PlateTM to
prevent rust.
20
bühler
2500 Bale Carrier
APPENDIX LIST
Description
Appendix
Assembly Instructions……………….…….………………………………….
A
Hydraulic Assembly……………...……………………………………………
B
Electrical Assembly……………...………………………………..…………..
C
General Assembly……………………………………….…………………...
D
21
bühler
2500 Bale Carrier
APPENDIX A
Assembly Instructions
Table of Contents
Description
Taillight Assembly……………………………………………………………………
Center Bale Stop…………………………………………………………………….
Fixed Lift Arm..……………………………………………………………………….
Bale Deflector Arm Assembly.……………………………………………………..
RPU Assembly………………………………………………….…………………...
22
Page
23
23
23
24
24
bühler
2500 Bale Carrier
CAUTION
Make sure area is clear of obstructions, well lit, and has
sufficient room for safe assembly. Do not work underneath raised assembly.
CAUTION
Ensure the carrier’s tires and hitch are securely blocked.
Otherwise, verify the 2500 Bale Carrier is properly coupled to the drawbar on a tractor
with a minimum of 25000 LB (11340 kg).
1. Tail Light Assembly
Refer to carrier final assembly drawing in Appendix D.
YELLOW LENS OUTSIDE
Remove all required hardware from parts box.
Ensure taillights are installed correctly, refer to
illustration.
TO
CENTER
Connect the tail light wiring harnesses to their
OF
appropriate connections.
HAYLINER
Connect main lighting plug to tractor.
Test by verifying correct lamps illuminate
VIEWED FROM THE FRONT
when signalling and braking.
RIGHT HAND SIDE
2. Centre Bale Stop
Remove the hardware that is attached to the center bale stop and place center
bale stop bar on bolt plates in the position shown at the beginning of the manual.
Torque the provided hardware to the specifications listed on the bolt chart. Tie
wrap the hydraulic hoses that run to the lift and tilt cylinders under the roll bar.
NOTE:
Hydraulic Assembly methods and layouts are common to the right and left
sides. Only one side of each component is shown in this manual.
CAUTION
Stay clear of the arms when testing a finished assembly.
Ensure during assembly to keep your entire body out from underneath parts that are
being attached to the main frame.
3. Fixed Lift Arm
Remove lift arm pivot pins that are installed
on the 2500 Bale Carrier.
Thoroughly lubricate all pins involved in the
assembly with a SAE multi purpose grease.
Align arm to pivots with open end of arm
facing forward and reinstall pins with
hardware provided and torque to
specifications called for in the bolt chart.
Remove the lift cylinder pin from the arm.
23
36.0"
FIXED LIFT ARM
ATTACHMENT
bühler
2500 Bale Carrier
Align the lift cylinder rod and reinstall the pin.
Adjust the outside bale fork to be positioned at the end of the lift arm and the
inner bale fork about 36” (91 cm) from the end.
Recheck all hardware so that every bolted connection on the lift arm is torqued
according to the specifications of the bolt chart.
Approach the bale and inspect to ensure the spacing of the forks is accurate.
For first operation, cycle the lift arm slowly with a bale and inspect just before
lifting bale from ground.
Finish the cycle and observe how the bale transits from the forks to the carrier
beam. If transition is smooth with minimum bale binding, assembly is completed.
If not, adjust the forks to a different location and try until loading is smooth.
4. Bale Deflector Arm Assembly
Remove all hardware that is included with the
deflector assembly.
Remove the two top bolts from outer fork on
lift arm.
Maintain the spacing of the forks if already
preset. If not, set spacing as described in the
fixed pick up arm assembly section.
Insert the coned end of the deflector onto the
end of the outer fork.
Align the bolt holes from the removed bolts
on the outer fork and the end of the deflector
attachment.
Insert hardware supplied with the deflector
the same way the hardware was installed
before the attachment was added.
Torque all hardware according to the bolt
chart and tighten the set screws on the cone
also according to the chart.
During first bale lift, cycle slowly and watch
for excessive flexing or movement of the
deflector. If movement is detected, stop cycle
and re-torque all hardware involved.
BALE DEFLECTOR ATTACHMENT
ASSEMBLY LAYOUT
5. RPU Assembly
Remove the lift cylinder pin from the RPU arm.
Remove lift cylinder and install Pilot Check
assembly (see Appendix B)
Remove lift cylinder and install Pilot Check a
assembly (see Appendix B)
RPU ATTACHMENT
ASSEMBLY LAYOUT
24
bühler
2500 Bale Carrier
Reinstall cylinder at base end only.
Lubricate all pins involved in RPU attachment with a SAE multi purpose grease
Align arm to pivots with open end of arm facing away from the 2500 Bale Carrier and
reinstall pins with hardware provided and
torque to specifications called for in the bolt chart.
Align the lift cylinder rod and reinstall the pin.
ADJUSTABLE FORK
Adjust the outside bale fork to be positioned at
the end of the lift arm and the inner bale fork 6”
(15 cm) to 8” (20 cm) bigger than the size of
BALE WIDTH + 6” TO 8”
bale that is being loaded.
Install the hydraulics according to the way the
hydraulic assembly Appendix B calls for.
ROTATING PICK UP ARM
Recheck all hardware so that every bolted and
hydraulic connection on the lift arm is torqued according to the specifications of
the torque charts.
Depress lift arm up. The RPU cycle should begin with a squeeze action, then lift
and rotate. After rotation is complete the lift continues until the bale is above the
carrier beams.
Release LIFT ARM UP when bale is above the carrier beam. Depress LIFT ARM
DN to release the bale and return to ground level ready for the next bale.
For the first operation, cycle the lift arm slowly with the bale and observe the
RPU operation.
Approach the bale slowly; once the bale is captured in the forks press the lift
switch. The bale is squeezed until the pressure in the sequence valve which is
preset at 1800 PSI (12400 KPA) has been achieved.
If bale is not held in between the forks increase the sequence valve pressure by
turning the setscrew clockwise. Refer to the RPU Rotate Cylinder drawing for
adjustment location of the setscrew. Verify that the fork spacing is accurate and
refer to the drawing on this page for fork adjustments.
The lift and rotate sequence won’t begin until the clamp pressure is met within
the sequence valve.
When the clamp pressure is met, the lifting action should start before the rotating
action to minimize bale damage from the moving ground.
To increase lift prior to rotate turn the restrictor knob clockwise. Refer to the RPU
Rotate Cylinder drawing for more information.
Continue to raise the bale until it is positioned above the carrier beam.
To release the bale, press lift arm down.
Finish the cycle and observe how the bale transits from the forks to the carrier
beam. If transition is smooth with minimum bale binding, assembly is completed.
If not, adjust the forks to a different location and try until loading is smooth.
25
bühler
2500 Bale Carrier
APPENDIX B
Hydraulic Assembly
NOTE:
1) Hydraulic Assembly methods and layouts are common to the right and
left sides. Only one side of each component is shown in this manual.
2) Seal Kits and Service Parts are only listed in the parts lists and are not indicated on
the illustrations.
Table of Contents
Description
Carrier Hydraulic Assembly Schematic…………………………………………...
Valve Bank Assembly………….….……………………………………….…....
FPS Directional Valve Bank Assembly……………………………………...
Series Parallel Valve (Low and High Speed)……………………………….
Hydraulic Return Line Assembly………………………………………………..
Hydraulic Pressure Line Assembly……………………………………………...
Carrier Tilt Assembly……………………………………………………………..
Fixed Pick Up Cylinder Assembly………………………………………………
Carrier Tilt Cylinders Hydraulic 3/8 line………………………………………...
Pusher Motor Assembly………………………………………………………….
Carrier Hydraulic Assembly Hardware…………………………………………
Fixed Pick Up Arm Hydraulic Assembly Schematic……………………………..
RPU Hydraulic Assembly…………………………………………………………...
RPU Squeeze Cylinder…………………………………………………………..
RPU Lift Cylinder………………………………………………………………….
Pilot Check Valve Assembly………………………………………………….
RPU Rotate Cylinder……………………………………………………………..
Open-Center Configuration Schematic.…………………………………………..
Open-Center Valve Assembly…………………………………………………..
2500 Bale Carrier Hydraulic Schematic…………………………………………..
26
Page
27
29
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
49
TO TRACTOR
COUPLER (RETRACT)
TO TRACTOR
COUPLER (EXTEND)
*812270
*29172
27
TO TRACTOR
COUPLER (EXTEND)
TO TRACTOR
COUPLER (RETURN)
*812270
bühler
2500 Bale Carrier
Carrier Hydraulic Assembly Schematic (Part # A7000-04) - Standard Configuration
bühler
2500 Bale Carrier
Carrier Hydraulic Assembly (Part # A7000-04)
Standard Configuration
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
Component
Part #
115169
29108
29110
29176
A7005-00
A7010-00
A7011-00
A7012-00
A7013-00
A7014-00
A7007-00
29105
886704
Description
HOSE 3/8 X 132 9/16 SWFJIC X SWFJIC
HOSE 1/2 X 16 3/4 SWFJIC X SWFJIC
HOSE 1/2 X 32 3/4 SWFJIC X SWFJIC
HOSE 1/2 X 54 3/4 SWFJIC X SWFJIC
VALVE BANK ASSEMBLY
HYD ASSY 1/2 X 130 RETURN LINE
HYD ASSY 1/2 X 130 PRESSURE LINE
TILT ASSY 3.0 X 16.0 CYLINDER
TILT ASSY LIFT ARM CYLINDER
TILT ASSY CYLINDER 3/8 HYDRAULIC LINE
PUSHER MOTOR ASSEMBLY
HOSE 1/2 X 28 3/4 SWFJIC
ADAPTOR STR. 3/4 MJIC
Note: All items marked with (*) are not supplied on the main assembly.
28
Qty
4
4
4
2
1
1
1
1
3
2
2
2
1
bühler
2500 Bale Carrier
Valve Bank Assembly (Part # A7005-00)
Open-Center Configuration
**
2450 PSI PLUGS TO FRONT
(**) To be used only with OPEN-CENTER configuration.
29
bühler
2500 Bale Carrier
Valve Bank Assembly (Part # A7005-00)
Open-Center Configuration
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Component
Part #
C7041-00
C7042-00
B7009-00
E2781-00
A7016-00
E7050-00
81549
812362
813667
812081
811414
812107
810582
B7010-00
812080
C7043-00
Description
VALVE BANK MOUNT WELDMENT LH
VALVE BANK MOUNT WELDMENT RH
FPS DIRECTIONAL VALVE ASSY (22214)
FLOW RESTRICTOR 0.25 DIA
OPEN-CENTER VALVE ASSY
PAN / VALVE BANK
BOLT HEX 0.313NC X 0.75 GR5PL
NUT LOCK (STEEL) 0.313NC GRBPL
TEE RUN 1/2 MJIC X 3/4 MORB
PLUG 3/4 MORB STL 721-FS0-08
ELBOW 90 3/4 MORB X 3/4 MJIC
ADAPTOR STR 3/4 MORB X 9/16 MJIC
BOLT HEX 0.313NC X 3.00 GR5PL
SERIES/PARALLEL VALVE (2-SPEED)
ADAPTOR STR 3/4 MORB X 3/4 MJIC
OPEN CENTER MOUNT WELD’T
30
Qty
1
1
1
1
1
1
8
15
5
7
3
4
6
2
8
1
bühler
2500 Bale Carrier
FPS Directional Valve (Part # B7009-00)
2
1
1
2
3
4
B7009-00 FPS Valve Service Parts
Item
1
2
Component
Part #
22208-02
22149
3
4
5
6
22208-01
22208-04
X2684
813842
Description
MV4-17 LOCK VALVE
CROSS OVER RELIEF VALVE BALE CARRIER SET
@ 800 / 2450 PSI
MVA-17 SPOOL SECTION
C07-12TA COIL
SEAL KIT VALVE BANK (ITEM NOT VISIBLE)
BOLT KIT VALVE (4) BANK
31
Qty
2
2
4
8
4
1
bühler
2500 Bale Carrier
Series/Parallel Valve Low and High Speed (Part # B7010-00)
2
1
B7010-00 Parallel Valve Service Parts
Item
1
2
3
Component
Part #
22083-03
22083-01
X2684
Description
C07-12TD COIL
SERIES PARALLEL VALVE (LOW & HIGH SPEED)
SEAL KIT VALVE BANK (ITEM NOT VISIBLE)
32
Qty
1
1
1
bühler
2500 Bale Carrier
Hydraulic Return Line Assembly (Part # A7010-00)
1
3
2
5
4
Item
1
2
3
4
5
Component
Part #
29170
812841
813119
813305
813666
Description
HOSE 1/2 X 130 3/4 MORB X 3/4
MALE TIP 0.5 BODY 0.75 ORB
ADAPTOR STR 3/4 MORB X 3/4 MORB
DUST CAP 0.5 BLACK
VALVE CHECK 3/4 ORB LINE
33
Qty
1
1
1
1
1
bühler
2500 Bale Carrier
Hydraulic Pressure Line Assembly (Part # A7011-00)
1
2
3
Item
1
2
3
Component
Part #
29170
812841
813303
Description
HOSE 1/2 X 130 3/4 MORB X 3/4
MALE TIP 0.5 BODY 0.75 ORB
DUST CAP 0.5 RED
34
Qty
1
1
1
bühler
2500 Bale Carrier
Carrier Tilt Assembly (Part # A7012-00)
1
3
5
1
5
4
2
Item
1
2
3
4
5
Component
Part #
29172
22510
813640
E2872-00
887572
Description
Qty
HOSE 3/8 X 18 9/16 SWFJIC X SWFJIC
CYLINDER 3.0 DIA X 16 INLAND
ELBOW 90 9/16 MORB ADJ 9/16 MJIC
ELBOW RESTRICTOR MALE 90°
TEE 9/16 MJIC X 9/16 SWFJIC
2
1
1
1
2
22510 Cylinder 3.0 Diameter Service Parts
Component
Part #
813407
X2504
24957
115519
24958
Description
LOCKNUT 1.00 NF
SEAL KIT FOR ITEM 22510
TUBE WELDMENT 3.0 DIA
SHAFT WELDMENT 1.50 X 22.63
HEAD PLATE 3.0 X 1.50
35
Qty
1
1
1
1
1
bühler
2500 Bale Carrier
Fixed Pick Up Cylinder Assembly (Part # A7013-00)
TO LIFT PORT ON MAIN VALVE BANK (FRONT PORT)
USE 3/8 X 132" HOSE SUPPLIED WITH MAIN FRAME
1
TO LIFT PORT ON VALVE BANK (REAR PORT)
USE 3/8 X 132" HOSE SUPPLIED WITH MAIN FRAME
3
2
Item
1
2
3
Component
Part #
813640
22510
E2872-00
Description
Qty
ELBOW 90 9/16 MORB ADJ X 9/16 MJIC
CYLINDER 3.0 DIA X 16 INLAND
RESTRICTOR ELBOW MALE 90
1
1
1
22510 Cylinder 3.0 Diameter Service Parts
Component
Part #
813407
X2504
24957
115519
24958
Description
LOCKNUT 1.00 NF
SEAL KIT FOR ITEM 22510
TUBE WELDMENT 3.0 DIA
SHAFT WELDMENT 1.50 X 22.63
HEAD PLATE 3.0 X 1.50
36
Qty
1
1
1
1
1
bühler
2500 Bale Carrier
Carrier Tilt Cylinders Hydraulic 3/8 Line (Part # A7014-00)
1
3
2
Item
1
2
3
Component
Part #
29173
812841
813303
Description
HOSE 3/8 X 216 9/16 SWFJIC X 3/4 MORB
MALE TIP 0.5 BODY 0.75 ORB
DUST CAP 0.5 RED
37
Qty
1
1
1
bühler
2500 Bale Carrier
Pusher Motor Assembly (Part # A7007-00)
8
4
6
7
1
9
5
2
10
Item
1
2
3
4
5
6
7
8
9
10
3
Description
Component
Part #
C7031-00
C7030-00
C2768-00
967275
84051
84048
813663
B2799-00
812270
811416
Qty
SPROCKET DRIVE WELDMENT
MOTOR 22.2 CU MT WELD
SPROCKET ADJUSTING BOLT FRONT 1NC
BOLT HEX 0.500 NC X 2.00 GR8PL
NUT HEX JAM 1.00 NC GR2
WASHER 0.500 FLAT SAE BS PL
NUT LOCK (STEEL) 0.500 NC GRCPL
MOTOR 22.2 CU PAINT YELLOW
HOSE 1/2 X 48 3/4 SWFJIC X 3/4 SWFJIC
ELBOW 90 7/8 MORB X 3/4 MJIC
1
1
1
4
1
4
4
2
1
4
B2799-00 Motor Service Parts
Component
Part #
X2725
Description
SEAL KIT FOR B2799-00
38
Qty
1
bühler
2500 Bale Carrier
Carrier Hydraulic Assembly Hardware (Part # A7000-04)
2
5
5
2
5
3
2
5
1
3
2
2
3
6
3
4
4
2
3
6
1
4
3
4
Item
1
2
3
4
5
6
Component
Part #
E7049-00
811795
812363
812364
E1932-00
E2345-00
Description
VALVE MT / U BOLT BALE CARRIER 0.5 NC
BOLT HEX 0.375 NC X 2.00 GR5PL
NUT LOCK (STEEL) 0.375 NC GRBPL
NUT LOCK (STEEL) 0.500 NC GRBPL
CYL PIN 1 DIA X 5 9/16 C1045
CYL PIN 1 DIA X 4.5
Note: Open-Center Valve is not shown.
39
Qty
2
6
6
4
4
2
A2300-86
FRONT OF
CARRIER
*A7013-00
*115169
40
*A7005-00
NOTES: 1) ALL ITEMS IN THE HYDRAULIC
SCHEMATIC THAT ARE MARKED WITH A "*"
ARE SUPPLIED ON THE MAIN FRAME
ASSEMBLY.
2) LOOP ALL HOSES THROUGH APPROPRIATE
HOSE HOLSTERS AND TIE WRAP.
3) DURING FIRST USE CHECK FOR
CLEARANCE AND BINDING.
*115169
bühler
2500 Bale Carrier
Fixed Pick Up Arm Hydraulic Assembly Schematic (Part # A2300-86)
41
L4
L5
L2
L3
DETAIL A
L6
L1
DETAIL B
L5
L6
NOTES: 1) THE LABELLED LINES IN THE SCHEMATIC
CORRESPOND WITH THE PORTS IN DETAIL VIEWS
A AND B. BRACKETS REPRESENT THE PART
NUMBER.
2) LOOP ALL HOSES THROUGH APPROPRIATE
HOSE HOLSTERS AND TIE WRAP
3) CHECK FOR HOSE CLEARANCE AND BINDING
DURING FIRST USE
4) ALL ITEMS THAT ARE MARKED WITH A "*" ARE
SUPPLIED ON THE MAIN FRAME.
B
L6 (812176)
L5 (29150)
L3 (IN29067)
L2 (*115169)
A
*A7005-00
FRONT OF
CARRIER
L1 (*115169)
L4 (IN29074)
bühler
2500 Bale Carrier
Hydraulic RPU Assembly Schematic (Part # A2400-34) (Optional)
bühler
2500 Bale Carrier
RPU Squeeze Cylinder (Part # A2400-35)
2
3
TO ROTATE CYLINDER ROD END
9/16 TEE OPEN END THAT POINTS IN
THE DIRECTION OF CYLINDER EXTENSION
2
1
4
TO ROTATE CYLINDER BASE END
9/16 TEE OPEN END
Item
1
2
3
4
Component
Part #
IN29074
813640
IN29067
24367
Description
Qty
HOSE 3/8 X 60 9/16 SWFJIC
ELBOW 90° 9/16 MORB ADJ X 3/8
HOSE 3/8 X 68 9/16 SWFJIC
CYLINDER 2.0 X 18.0 INLAND
1
2
1
1
24367 Cylinder 2.0 Diameter Service Parts
Component
Part #
811843
X1348
83224
812655
144521
114520
24366
115042
24516
Description
NOT GREASE NIPPLE 90 DEGREES
SEAL KIT FOR 24367 2.0 DIA CYLINDER
BACKUP WASHER 1.75 ID X 2.00 OD
0.875 UNF LOCKNUT
2.00 DIA PISTON HALF (NARROW)
2.00 DIA PISTON HALF (WIDE)
2.00 DIA TUBE WELDMENT
SHAFT WELDMENT 1.25 DIA X 24.125 LG
2.00 DIA HEAD PLATE
42
Qty
1
1
1
1
1
1
1
1
1
bühler
2500 Bale Carrier
RPU Lift Cylinder (Part # A2400-37 Assembled To Existing 22510 Cylinder)
CYLINDER PORT
(CHECKED FLOW IN)
3
2
SIDE PUMP
PORT (FREE
FLOW IN)
PILOT PORT
TO LIFT LOWER PORT ON MAIN VALVE
(FRONT PORT) USE EXISTING 3/8 X 132
HOSE SUPPLIED WITH MAIN FRAME
1
TO SEQUENCE VALVE (PORT #2)
USE EXISTING 3/8 X 108 HOSE SUPPLIED
WITH ROTATE CYLINDER ASSEMBLY
TO ROTATE CYLINDER BASE END
USE 3/8 X 96 HOSE SUPPLIED WITH
ROTATE CYLINDER ASSEMBLY
Item
1
2
3
Component
Part #
22510
E2872-00
A2400-37
Description
Qty
CYLINDER 3.0 DIA X 16 INLAND
RESTRICTOR ELBOW MALE 90°
PILOT CHECK VALVE ASSEMBLY
1
1
1
22510 Cylinder 3.0 Diameter Service Parts
Component
Part #
813407
X2504
24957
115519
24598
Description
LOCKNUT 1.00 NF
SEAL KIT FOR ITEM 22510
TUBE WELDMENT 3.0 DIA
SHAFT WELDMENT 1.50 X 22.63
HEAD PLATE 3.0 X 1.50
43
Qty
1
1
1
1
1
bühler
2500 Bale Carrier
Pilot Check Valve Assembly (Part # A2400-37)
1
3
2
4
5
6
7
Item
1
2
3
4
5
6
7
Component
Part #
IN29098
29043
22203
29020
29023
29039
29015
Description
HOSE 3/8 X 14 3/8 FNPT X 9/16 SWFJIC
ADAPTOR STR 9/16 MJIC X 3/8 MNPT
PILOT CHECK VALVE PC-37
CONNECTOR 9/16 MJIC X 1/4 MNPT
TEE 1/4 FNPT RUN X 1/4 MNPT
ADAPTOR STR 1/4 MNPT X 9/16 FJIC
TEE 9/16 MJIC RUN X 9/16 MORB
44
Qty
1
1
1
1
1
1
1
bühler
2500 Bale Carrier
RPU Rotate Cylinder (Part # A2400-36)
2
3
1
4
TO LIFT CYLINDER PILOT
CHECK VALVE "SIDE"
PUMP PORT
8
5
6
2
TO SQUEEZE CYLINDER ROD END
USE 3/8 X 68 HOSE SUPPLIED WITH
SQUEEZE CYLINDER ASSEMBLY
1
3
FLOW CONTROL
CLOCKWISE ADJUSTMENT
-INCREASES LIFT
-DECREASES ROTATE
COUNTER CLOCKWISE ADJUSTMENT
-INCREASES ROTATE
-DECREASES LIFT
7
11
TO LIFT RAISE PORT ON MAIN VALVE
(REAR PORT) USE BASE END LIFT CYLINDER
3/8 X 132 HOSE SUPPLIED WITH MAIN FRAME
ASSEMBLY
SEQUENCE VALVE ENSURES THE BALE IS ADEQUATELY
SQUEEZED WITHIN THE FORKS. PRESET TO 1800 PSI CLAMP
PRESSURE. CLOCKWISE ADJUSTMENT INCREASES CLAMP
PRESSURE, COUNTER CLOCKWISE DECREASES PRESSURE
TO SQUEEZE CYLINDER BASE END
USE 3/8 X 60 HOSE SUPPLIED WITH
SQUEEZE CYLINDER ASSEMBLY
9
13
12
15
TO LIFT CYLINDER ROD END USE
9/16 MJIC TEE FOR CONNECTION
14
16
10
"BOTTOM ISOMETRIC VIEW"
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Component
Part #
29150
29149
22060
29016
20877
811631
29015
29022
22075
984077
29047
813691
887572
E2430-00
812176
E2478-00
Description
Qty
HOSE 3/8 X 108 9/16 SWFJIC X 3
RESTRICTOR ONE WAY ADJ PARKER
3 X 8 TIE ROD CYLINDER
ELBOW 90 1/4 MNPT X 9/16 MJIC
PRESSURE LINE / SEQUENCE TUBE
BOLT HEX JAM 0.500 NC GR2PL
TEE 9/16 MJIC RUN X 9/16 MJIC
ELBOW 90 1/4 MNPT X 9/16 MORB
SUN SEQUENCE VALVE SET 1800 psi
NUT HEX JAM 0.500 NC GR2PL
ELBOW 90 9/16 MORB X 3/8 MJIC LG
SEQUENCE VALVE VENT TUBE
TEE 9/16 MJIC X 9/16 SWFJIC
SEQUENCE VALVE HOLDER
HOSE 3/8 X 96 9/16 SWFJIC X 3
HYDRAULIC CYLINDER TIE ROD
1
1
1
1
1
2
3
1
1
1
1
1
1
1
1
1
22060 Cylinder 3.0 Diameter Service Parts
Component
Part #
22060-02
Description
SEAL KIT FOR 22060 CYLINDER
45
Qty
1
bühler
2500 Bale Carrier
Open-Center Configuration Schematic
NOTE: ITEMS IN THE SCHEMATIC THAT ARE
MARKED WITH A "*" ARE SUPPLIED ON THE
MAIN FRAME ASSEMBLY.
*A7005-00
*A7010-00
29105
TO TRACTOR
COUPLER (RETURN)
A7016-00
TO TRACTOR
COUPLER (EXTEND)
*A7011-00
29105
46
bühler
2500 Bale Carrier
Open-Center Valve (Part # A7016-00)
Open-Center Configuration
47
bühler
2500 Bale Carrier
Open-Center Valve (Part # A7016-00)
Open-Center Configuration
Item
1
2
3
4
5
6
Component
Part #
B7010
812081
812080
811414
813667
29105
Description
Qty
SERIES/PARALLEL VALVE
PLUG 3/4 MORB STL 721-FS0-08
ADAPTOR STR 3/4 MORB X 3/4 MJIC
ELBOW 90 3/4 MORB X 3/4 MJIC
TEE RUN 3/4 MJIC X 3/4 MORB
HOSE 1/2 X 28 - 3/4 SWFJIC
1
3
1
1
1
2
B7010-00 Parallel Valve Service Parts
Component
Part #
22083-03
22083-01
X2684
Description
C07-12TD COIL
SERIES/PARALLEL VALVE (LOW & HIGH SPEED)
SEAL KIT VALVE BANK
48
Qty
1
1
1
bühler
2500 Bale Carrier
2500 Bale Carrier Hydraulic Schematic
49
bühler
2500 Bale Carrier
NOTES PAGE
50
bühler
2500 Bale Carrier
APPENDIX C
Electrical Assembly
WARNING
Read and understand the safety messages listed in the 2500
Bale Carrier operator manual. Shut off all power to unit before inspecting, servicing,
adjusting or repairing the 2500 Bale Carrier.
WARNING
For proper operation of the Snubber, power must be supplied
to the RED power wire from the control handle. Ensure that there is a 15 amp fuse in
place to protect this circuit. Verify prior to installing Snubber. Incorrect wiring will result
in electrical failure.
NOTE:
The snubber unit is designed to protect the momentary control switches.
The snubber minimizes coil voltage discharge during the de-energizing of the valve
solenoid coils. There are no serviceable parts within the unit. Ensure that all electrical
connections are clean and dry. Test the 2500 Bale Carrier and view to see if the
hydraulic system is operating correctly. If any wires are damaged or cut, the schematic
on the next page will assist in repair and maintenance. All wire is 18 gage.
Table of Contents
Description
Page
Electrical Schematic………………………………………………………………... 52
Electrical Assembly ………………………………………………………………… 53
51
bühler
2500 Bale Carrier
Electrical Schematic
LH LOW SPEED 13-BLACK-WHITE
2
LH PUSHER BACK 9-GREY
1
LH ARM UP 10-WHITE
4
LH ARM DN 11-PURPLE
3
LH PUSHER FWD 8-YELLOW
RH PUSHER FWD. 6-BLUE
RH ARM DN. 4-PINK
NOTE: 1) VALVE HARNESS (1) TERMINATES
WITH THE FEMALE SPADE CONNECTORS
TO MATCH THE SOLENOID COIL.
2) ITEM 3 IS SUPPLIED WITH THE PARTS
BOX A7009-00.
OPEN CENTER 5-ORANGE
5
GROUND 12- GREEN
RH ARM UP 2 - TAN
RH PUSHER BACK. 7-BROWN
RH LOW SPEED 1-BLACK
END VIEW CONNECTOR
FRONT OF HAYLINER
POWER 3-RED
15 AMP FUSE
GROUND 12- GREEN
POWER 3-RED
GROUND 12- GREEN
LOW SPEED RH 1-BLACK
RH PUSHER FWD. 6-BLUE
LOW SPEED RH 1-BLACK
RH PUSHER BACK 7-BROWN
RH ARM DN. 4-PINK
26
24
13
11
12
13
11
12
26
24
25
26
24
25
13
11
12
13
11
12
25
26
24
25
24
25
11
12
RH ARM UP 2-TAN
POWER 3-RED
OPEN CENTER 5-ORANGE
LH ARM DN. 11-PURPLE
LH ARM UP 10-WHITE
LH PUSHER BACK 9-GREY
LOW SPEED LH 13
LH PUSHER FWD 8-YELLOW
LOW SPEED LH 13-BLACK-WHITE
Item
1
2
3
4
5
Component
Part #
A7022-02
813949
A7022-00
A7005-00
A7016-00
Description
MACHINE HARNESS 2500 BALE CARRIER
SNUBBER UNIT
CONTROL HANDLE HARNESS ASSEMBLY
VALVE BANK ASSEMBLY
OPTIONAL OPEN CENTER KIT
52
Qty
1
1
1
1
1
bühler
2500 Bale Carrier
Control Handle Assembly (Part # I20055)
3
5
4
6
2
8
7
1
Item
1
2
3
4
5
6
7
8
Component
Part #
A7022-01
22105
813539
INE22106
813779
814445
813540
INE22105-01
Description
CONTROL HANDLE WIRES 2500 BALE CARRIER
CONTROL HANDLE
8-32 X 3/8 TRUSS HEAD MACHINE SCREW
SWITCH COVER PLATE
ROCKER SWITCH ON / OFF
ROCKER SWITCH ON / OFF MOMENTARY
8-32 X 1/2 ROUND HEAD MACHINE SCREW
WIRE CLAMP PLATE
53
Qty
1
1
4
1
1
4
2
1
bühler
2500 Bale Carrier
NOTES PAGE
54
bühler
2500 Bale Carrier
APPENDIX D
General Assembly
Table of Contents
Description
Carrier Final Assembly…………………..………………………………………….
Carrier Initial Assembly……………………………………………………….…….
Tandem Axle Assembly………………………………………………………….
Tire Assembly………………………………………………………………….
Tandem Axle Assembly………………………………………………………
Hub Assembly……………………………………………………………….
Pusher Assembly…………………………………………………………………
Roller / Chain Guide Assembly………………………………………………….
Fixed Pick Up Arm Assembly………….…………………………………………..
RPU Assembly…………………………………..………………………………….
Bale Deflector Assembly……………………………………………………………
Slow Moving Vehicle Sign Assembly………………………………….………….
55
Page
56
58
60
61
62
63
64
65
66
70
74
78
3
19
25
27
22
33 45 17
36 46
AMBER LAMP TO
THE OUTSIDE
37
51
40 53 50
15
39 49
56
7
4
28
27
43 53 51
28
9
26
RIGHT TAIL LIGHT CONNECTOR WIRE ORDER:RED
WHITE
GREEN
BROWN
10
AS VIEWED FROM BACK OF TRAILER
LEFT TAIL LIGHT CONNECTOR WIRE ORDER BLACK
WHITE
YELLOW
BROWN
RED LAMP
TO THE INSIDE
41 50 51
40 53 50
20
AMBER LAMP TO
THE OUTSIDE
31
29
MAIN ELECTRICAL HARNESS
16
42 53 51 14
8
40 53 50
18
44 54 48
18
11
6
2
12
35
30
23
32
40 53 55
58 59
60
47 52
5
33 45
38
56 57
20
38 54 48
13
24
1
21
bühler
2500 Bale Carrier
Carrier Final Assembly (Part # A7000-04)
bühler
2500 Bale Carrier
Carrier Final Assembly (Part # A7000-04)
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Part #
A7006-00
A7007-00
A7008-00
A7017-00
B2363-00
C7007-01
C7012-00
C7034-00
C7035-00
C7036-00
C7048-00
C7054-01
C7057-01
C8010-00
E2345-00
E2413-00
E2937-00
E7040-00
INE7003-01
INE7038-00
INE7039-00
INE7045-00
52955-456
813643
814195
814196
814193
814197
813646
814198
813602
813641
813958
99053
813949
81527
812217
81549
811795
81620
967274
967275
81629
81552
812537
81922
84541
812362
812363
812364
813663
81546
84048
81570
813581
909277
P4186
814433
814449
814450
Description
PUSHER ASSEMBLY
MOTOR MOUNT ASSEMBLY
ROLLER / CHAIN GUIDE ASSEMBLY
SLOW MOVING VEHICLE ASSEMBLY
HOSE HOLDER
SECOND CROSSMEMBER WELDMENT
REAR CROSSMEMBER WELDMENT
FRONT BRACE WELDMENT
REAR BRACE WELDMENT
CENTER BRACE WELDMENT
ROLL BAR
FRONT CROSSMEMBER WELDT
CHAIN GUIDE WELDT
SAFETY CHAIN WELDMENT
CYL PIN / 1.0" X 4 1/4"
ARM CUSHION
PLATE 1500/2500 LIGHTING KIT
CUSHION / PUSHER STOP
REAR CHAIN PLATE CROSSMEMBER
MOUNTING BRACKET / SHIELD
SHIELD / CHAIN DRIVE
LIGHT BRACKET PLATE
C2080H ROLLER CHAIN ( 76' PER PUSHER )
C2080H CONNECTOR LINK HD
DUAL LAMP w/BRAKE LH/H RH/V
DUAL LAMP w/BRAKE RH/H LH/V
ENHANCED AG LIGHTING MODULE
EXTENSION HARNESS 114” LG
GREASE FITTING 1/4 NF DRIVEN
MAIN HARNESS 48FT LONG 7 PIN PLUG
RIVET 1/4" X 3/4" FLHD
SAFETY CHAIN 30M GVW
SCREW MACH #8-32 X 0.75
SLIP PLATE BEAM COATING ( NOT VISIBLE)
SNUBBER UNIT 1500/2500 BALE CARRIER
BOLT HEX 0.25NC X 1.00 GR 5 PL
BOLT CARRIAGE 0.500NC X1.25GR5 PL
BOLT HEX 0.313NC X 0.75GR5 PL
BOLT HEX 0.375NC X 2.00GR5 PL
BOLT HEX 0.500NC X 1.25GR5 PL
BOLT HEX 0.500NC X 1.50GR8 PL
BOLT HEX 0.500NC X 2.00GR8 PL
BOLT HEX 0.500NC X 3.50GR5 PL
BOLT HEX 0.313 NC X 1.25 GR5PL
NUT LOCK (NYLOCK) #8-32 STEEL
NUT LOCK (NYLOCK) 0.25NC GRB PL
NUT LOCK (NYLON) 0.313NC GRB PL
NUT LOCK (STEEL) 0.313NC GRB PL
NUT LOCK (STEEL) 0.375 GRB PL
NUT LOCK (STEEL) 0.500NC GRB PL
NUT LOCK (STEEL) 0.500NC GRC PL
WASHER FLAT STD 0.313 HS PL
WASHER FLAT SAE 0.500 BS PL
WASHER FLAT STD 0.375 HS PL
WASHER FLAT 1.5 X 0.531 X 0.25 PL
MANUAL HOLDER
OPERATOR’S & PARTS MANUAL
WARRANTY REGISTRATION SHEET
GOODYEAR TIRE WORKMANSHIP WARRANTY (700-862-905-128)
GOODYEAR TIRE STUBBLE WARRANTY (700-862-905-129)
57
Qty
2
2
2
1
1
1
1
2
2
2
1
1
2
2
2
2
1
2
2
2
2
2
152’
6
1
1
1
1
4
1
4
1
6
1 QT.
1
8
8
8
2
41
55
19
4
4
6
8
4
8
2
41
86
1
122
8
1
1
1
1
1
1
bühler
2500 Bale Carrier
13 20 16
9
8
4
13 2016
14 17
3
10
12
6
7
13 2016
11
5
2
15 19 19 18
Carrier Initial Assembly (Part # A7000-04)
58
bühler
2500 Bale Carrier
Carrier Initial Assembly (Part # A7000-04)
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Component
Part #
A7004-00
C2369-00
C7000-01
C7001-01
C7006-00
C7008-00
C7016-00
C7055-00
C7056-00
E2348-00
813685
81207
967274
813053
813515
813663
813731
813648
813590
84048
Description
TANDEM AXLE ASSEMBLY
HITCH CLEVIS WELDMENT
LEFT SUBFRAME
RIGHT SUBFRAME
LEFT HITCH BEAM WELDMENT
HITCH CROSSMEMBER WELDMENT
RIGHT HITCH BEAM WELDMENT
OUTER CARRIER BEAM
INNER CARRIER BEAM
HITCH BEAM PIN
5 TON SCREW JACK
COTTER PIN 0.188 X 2.00 POL
BOLT HEX 0.500NC X 1.50GR8 PL
BOLT HEX 0.625NC X 1.50GR8 PL
BOLT HEX 0.750NC X 2.50GR8 PL
NUT LOCK (STEEL) 0.500NC GRC PL
NUT LOCK (STEEL) 0.625NC L9 PL
NUT LOCK (STEEL) 0.750NC GRC PL
WASHER FLAT 1.25X0.781X0.25 PL
WASHER FLAT SAE 0.500 BS PL
59
Qty
2
1
1
1
1
1
1
2
2
2
1
4
100
12
4
100
12
4
8
100
bühler
2500 Bale Carrier
Tandem Axle Assembly (Part # A7004-00)
1
3
4
2
Item
1
2
3
4
Component
Part #
C2322-00
813646
B2700-03
B2722-00
Description
AXLE BEARING WELDMENT
GREASE ZERK 1/4" SELF TAPPING
TIRE ASSEMBLY
TANDEM AXLE 2500/4000 BALE CARRIER
60
Qty
2
2
4
1
bühler
2500 Bale Carrier
Tire Assembly (Part # B2700-03)
3
1
2
Item
1
2
3
Component
Part #
813655
813656
813657
Description
Qty
15 X 10lb X 6 BOLT P65 RIM
TR-416-MS VALVE STEM WITH CAP
TIRE 12.5 X 15FI 12 PLY RANGE F FARM HWY TIRE
4
1
1
61
bühler
2500 Bale Carrier
Tandem Axle Assembly (Part # B2722-00)
7
6
5
2
4
1
3
4
Item
1
2
3
4
5
6
7
Component
Part #
C2722-00
81206
813649
813651
813673
813650
C2339-00
Description
TANDEM AXLE WELDMENT
3/16" X 1-1/2 " COTTER PIN BLACK
DUST SHIELD
WASHER FLAT 1-1/32" X 2" X .188" BLK.
NUT CASTLE 1.00 NF
DUST CAP
HUB ASSEMBLY
62
Qty
1
4
4
4
4
4
4
bühler
2500 Bale Carrier
Hub Assembly (Part # C2339-00)
2
1
3
4
5
Item
1
2
3
4
5
Component
Part #
813652
967205
967208
967204
813653
Description
6 BOLT WHEEL HUB
BEARING CONE OUTER
BEARING CONE INNER
OIL SEAL SAE-30
9/16" HUB BOLT
63
Qty
1
1
1
1
6
bühler
2500 Bale Carrier
Pusher Assembly (Part # A7006-00) **
1
4
3
2
7
5
4
3
5
4
6
2
4
Item
1
2
3
4
5
6
7
Component
Part #
C7027-00
E2749-00
E2750-00
813558
813561
E7032-00
813644
NOTE: USE LOCKTITE ON ALL
BRASS SCREWS
Description
PUSHER
TOP SLIDER
SIDE SLIDER
SCREW MACH M8 X 20 FLHD BRASS
NUT HEX M8 BRASS
CENTER SLIDER
SCREW MACH 0.313NC X 1.25 RDHD
(**) Note: Two pushers are installed.
64
Qty
1
2
2
16
16
1
4
bühler
2500 Bale Carrier
Roller / Chain Guide Assembly (Part # A7008-00)
1
2
1
Item
1
2
Component
Part #
813645
INE7037-00
Description
BEARING / 6205LLU/25.4/3E
ROLLER / CHAIN GUIDE
65
Qty
2
1
bühler
2500 Bale Carrier
Fixed Pick Up Arm Assembly LH Side (Part # A2300-86)
10
13
11
6
2
7
6
5
2
13
8
3
7
9
7
5
7
1
14
3
4
ITEM 3 NOT VISIBLE
66
12
bühler
2500 Bale Carrier
Fixed Pick Up Arm Assembly LH Side (Part # A2300-86)
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Component
Part #
811795
812087
812363
812364
813509
81581
81677
84277
C2315-00
C2329-00
C2330-00
E2345-00
E2445-00
INE2485-00
Description
BOLT HEX 0.375 NC X 2.00 GR5PL
BOLT HEX 0.625 NC X 6.00 GRBPL
NUT LOCK (STEEL) 0.375 NC GRBPL
NUT LOCK (STEEL) 0.500 NC GR5PL
NUT HEX 0.625 NC GR5PL
BOLT HEX 0.375 NC X 2.50 GR5PL
WASHER LOCK 0.625 PL
BOLT HEX 0.500 NC X 1.50 GR5PL
LIFT ARM LEFT BALE
FORK BALE LEFT ASSEMBLY
FORK BALE RIGHT ASSEMBLY
PIN CYLINDER 1.0 DIA X 4.5
PIN LIFT ARM 1.25 DIA C1045 CR
CHAIN LATCH LIFT ARM
67
Qty
1
4
3
1
4
2
4
1
1
1
1
1
2
1
bühler
2500 Bale Carrier
Fixed Pick Up Arm Assembly RH Side (Part # A2300-87)
7
5
7
7
5
8
2
14
1
7
11
6
13
2
10
12
6
13
3
9
ITEM 3 NOT VISIBLE
68
4
bühler
2500 Bale Carrier
Fixed Pick Up Arm Assembly RH Side (Part # A2300-87)
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Component
Part #
811795
812087
812363
812364
813509
81581
81677
84277
C2316-00
C2329-00
C2330-00
E2345-00
E2445-00
INE2485-00
Description
BOLT HEX 0.375 NC X 2.00 GR5PL
BOLT HEX 0.625 NC X 6.00 GRBPL
NUT LOCK (STEEL) 0.375 NC GRBPL
NUT LOCK (STEEL) 0.500 NC GR5PL
NUT HEX 0.625 NC GR5PL
BOLT HEX 0.375 NC X 2.50 GR5PL
WASHER LOCK 0.625 PL
BOLT HEX 0.500 NC X 1.50 GR5PL
LIFT ARM RIGHT BALE
FORK BALE LEFT ASSEMBLY
FORK BALE RIGHT ASSEMBLY
PIN CYLINDER 1.0 DIA X 4.5
PIN LIFT ARM 1.25 DIA C1045 CR
CHAIN LATCH LIFT ARM
69
Qty
1
4
3
1
4
2
4
1
1
1
1
1
2
1
22
4
20
14
11*
70
7
15
14
29
21
9
28
28
31
9
30
29
30
31
16
35
2
6
2
33
13
36
10
8
24
12
23
19
34
6
5
26
1
3
5
5
3
18
32
17
25
12
27
5
8
34
37
bühler
2500 Bale Carrier
RPU Assembly LH Side (Part # A2400-34)
bühler
2500 Bale Carrier
RPU Assembly LH Side (Part # A2400-34)
ITEM
COMPONENT
PART#
DESCRIPTION
QTY
1
20252
BUSHING 1.75OD x 1.5ID x 1.75
2
2
810215
SCREW SELF TAP 0.313 NC X 0.50
8
3
811795
BOLT HEX 0.375NC X 2.00 GR5 PL
2
4
812087
BOLT HEX 0.625NC X 6.00 GRBPL
2
5
812363
NUT LOCK (STEEL) 0.375 GRB PL
4
6
812364
NUT LOCK (STEEL) 0.500NC GRB PL
2
7
813509
NUT HEX 0.625 NC GR5PL
2
8
813602
RIVET 1/4 X 3/4 FLATHEAD
4
9
813611
PIN SPRING 0.125 DIA X 0.625 LONG
4
10
813646
GREASE FITTING 1/4 NF DRIVEN
1
11*
813795
WASHER FLAT 1.031 X 1.75 X 0.031
1
12
81581
BOLT HEX 0.375NC X 2.50 GR5PL
2
13
81626
BOLT HEX 0.500NC X 2.75 GR5PL
1
14
81677
WASHER LOCK 0.625 PL
2
15
81978
COTTER PIN 0.125 X 2.00 POL
1
16
84277
BOLT HEX 0.500NC X 1.50 GR5PL
1
17
A2400-35
SQUEEZE CYLINDER ASSEMBLY RPU
1
18
A2400-36
ROTATE CYLINDER ASSEMBLY RPU
1
19
A2400-37
PILOT CHECK VALVE ASSY RPU
1
20
C2417-00
SLIDING ARM RPU
1
21
C2423-00
PIN SQUEEZE CYLINDER RPU
1
22
C2428-00
FORK ADJUSTABLE RPU LH
1
23
C2695-00
PIN HINGE RPU
1
24
C2696-00
LH STATIONARY ARM RPU
1
25
C2697-00
LIFT ARM RPU, LH
1
26
E2345-00
PIN CYLINDER 1.0 DIA X 4.5
1
27
E2413-00
ARM CUSHION RUBBER BELTING
1
28
E2419-00
ARM SLIDING TOP AND BOTTOM PAD
2
29
E2420-00
ARM SLIDING SIDE PAD
2
30
E2421-00
STATIONARY ARM TOP AND BOTTOM RPU PAD
2
31
E2422-00
ARM STATIONARY SIDE RPU PAD
2
32
E2424-00
PIN SQUEEZE CYLINDER CLEVIS
1
33
E2429-00
ARM STATIONARY CUSHION RPU
1
34
E2445-00
PIN LIFT ARM 1.25 DIA C1045CR
2
35
E2485-00
CHAIN LATCH LIFT ARM
1
36
967053
DECAL REFLECTIVE 2 X 9 RED
1
37
967055
DECAL REFLECTIVE 2 X 9 AMBER
1
Note: 1. Item #11 is used as needed.
71
32
3
5
17
24
6
13
25
1
2
8
10
31
8
72
27
33
30
29
9
2
28
34
30
28
9
37
31
18
22
21
9
11*
15
12
29
16
4
35
23
6
34
14
20
26
12
5
7
5
36
14
3
19
bühler
2500 Bale Carrier
RPU Assembly RH Side (Part # A2400-32) (Optional)
bühler
2500 Bale Carrier
RPU Assembly RH Side (Part # A2400-32) (Optional)
ITEM
Component
part #
DESCRIPTION
QTY
1
20252
BUSHING 1.75OD x 1.5ID x 1.75
2
2
810215
SCREW SELF TAP 0.313 NC X 0.50
8
3
811795
BOLT HEX 0.375NC X 2.00 GR5 PL
2
4
812087
BOLT HEX 0.625NC X 6.00 GRBPL
2
5
812363
NUT LOCK (STEEL) 0.375 GRB PL
4
6
812364
NUT LOCK (STEEL) 0.500NC GRB PL
2
7
813509
NUT HEX 0.625 NC GR5PL
2
8
813602
RIVET 1/4 X 3/4 FLATHEAD
4
9
813611
PIN SPRING 0.125 DIA X 0.625 LONG
4
10
813646
GREASE FITTING 1/4 NF DRIVEN
1
11*
813795
WASHER FLAT 1.031 X 1.75 X 0.031
1
12
81581
BOLT HEX 0.375NC X 2.50 GR5PL
2
13
81626
BOLT HEX 0.500NC X 2.75 GR5PL
1
14
81677
WASHER LOCK 0.625 PL
2
15
81978
COTTER PIN 0.125 X 2.00 POL
1
16
84277
BOLT HEX 0.500NC X 1.50 GR5PL
1
17
A2400-35
SQUEEZE CYLINDER ASSEMBLY RPU
1
18
A2400-36
ROTATE CYLINDER ASSEMBLY RPU
1
19*
A2400-37
PILOT CHECK VALVE ASSY RPU
1
20
C2417-00
SLIDING ARM RPU
1
21
C2418-00
FORK ADJUSTABLE RH RPU
1
22
C2423-00
PIN SQUEEZE CYLINDER RPU
1
23
C2499-00
LIFT ARM RIGHT
1
24
C2694-00
RH STATIONARY ARM RPU
1
25
C2695-00
PIN HINGE RPU
1
26
E2345-00
PIN CYLINDER 1.0 DIA X 4.5
1
27
E2413-00
ARM CUSHION RUBBER BELTING
1
28
E2419-00
ARM SLIDING TOP AND BOTTOM PAD
2
29
E2420-00
ARM SLIDING SIDE PAD
2
30
E2421-00
STATIONARY ARM TOP AND BOTTOM RPU PAD
2
31
E2422-00
ARM STATIONARY SIDE RPU PAD
2
32
E2424-00
PIN SQUEEZE CYLINDER CLEVIS
1
33
E2429-00
ARM STATIONARY CUSHION RPU
1
34
E2445-00
PIN LIFT ARM 1.25 DIA C1045CR
2
35
E2485-00
CHAIN LATCH LIFT ARM
1
36
967053
DECAL REFLECTIVE 2 X 9 RED
1
37
967055
DECAL REFLECTIVE 2 X 9 AMBER
1
Note: 1. Item #11 is used as needed.
2. Item #19 is an existing part installed on carrier.
73
bühler
2500 Bale Carrier
Bale Deflector Assembly LH (Part # A2400-17)
74
bühler
2500 Bale Carrier
Bale Deflector Assembly LH (Part # A2400-17)
Item
1
2
3
4
5
6
7
8
9
10
Component
Part #
812076
813507
813509
81593
81677
81914
C2452-00
E2456-00
813547
813508
Description
BOLT HEX 0.625 NC X 6.50 GR5PL
NUT HEX 0.375 NC GR5PL
NUT HEX 0.625 NC GR5PL
WASHER 0.375 LOCK PL
WASHER LOCK 0.625 PL
BOLT CARR 0.375 NC X 1.00 GR5PL
BALE DEFLECTOR LH MAIN FRAME
SKID COVER LH UHMW POLY
SET SCREW SQHDCUP 0.500 NC
NUT HEX 0.500NC GR5PL
75
Qty
2
9
2
9
2
9
1
1
2
2
bühler
2500 Bale Carrier
Bale Deflector Assembly RH (Part # A2400-16)
76
bühler
2500 Bale Carrier
Bale Deflector Assembly RH (Part # A2400-16)
Item
1
2
3
4
5
6
7
8
9
10
Component
Part #
C2451-00
E2453-00
81914
81593
813507
812076
81677
813509
813547
813508
Description
BALE DEFLECTOR RH MAIN FRAME
SKID COVER RH UHMW POLY
BOLT CARR 0.375 NC X 1.00 GR5PL
WASHER 0.375 LOCK PL
NUT HEX 0.375 NC GR5PL
BOLT HEX 0.625 NC X 6.50 GR5PL
WASHER LOCK 0.625 PL
NUT HEX 0.625 NC GR5PL
SET SCREW SQHDCUP 0.500 NC
NUT HEX 0.500 NC GR5PL
77
Qty
1
1
9
9
9
2
2
2
2
2
bühler
2500 Bale Carrier
Slow Moving Vehicle Sign Assembly (Part # A7017-00)
2
2
4
1
3
3
Item
1
2
3
4
Component
Part #
E2795-00
81525
84498
967066
Description
Qty
DECAL MOUNT SLOW MOVING VEHICLE SIGN
BOLT HEX 0.25 NC X 0.75 GR5PL
NUT LOCK (STEEL) 0.25 GRBPL
SLOW MOVING VEHICLE DECAL
1
2
2
1
78
bühler
2500 Bale Carrier
CHECKLIST
Pre-delivery
Verify Hardware Torque
Verify Rear Wheel Bolt Torque
Verify Tire Pressure
Inspect Bearing Seals
Inspect All Lubrication Points
Inspect Chain Drives
Inspect Hydraulic Hoses and Electrical Harnesses
Dealer Representative:
Date:
Customer Delivery
Review safety procedures regarding 2500 Bale Carrier operation and maintenance.
Review Operator’s and Part’s Manual.
Review proper operating procedures.
Review general adjustment and setup procedures.
Review chain tensioning procedures.
Review importance of regular lubrication.
Discuss road and highway transportation requirements and regulations.
Review front hitch height.
Dealer Representative:
Date:
79
bühler
2500 Bale Carrier
NOTES PAGE
80
DIVISION LOCATIONS
Inland Division
1260 Clarence Avenue
Winnipeg, Manitoba R3T 1T2
Ph.: (204) 661-8711
Fax: (204) 654-2503
Allied Division
1260 Clarence Avenue
Winnipeg, Manitoba R3T 1T2
Ph.: (204) 661-8711
Fax: (204) 654-2503
Farm King Division
301 Mountain Street S.
Morden MB.
R6M 1X7
Ph.: (204) 822-4467
Fax: (204) 822-6348
U.S. WAREHOUSES
AR, West Memphis
(870) 732-3132
ND, Bismarck
(701) 223-1886
GA, Stone Mountain
(770) 908-9439
ND, Fargo
(701) 282-7003
IA, Lakeview
(712) 657-8585
NY, Syracuse
(315) 463-5276
ID, Meridian
(208) 887-6006
OH, Youngstown
(330) 793-0862
IN, Clarksville
(812) 284-3376
OR, Portland
(503) 234-0378
KS, Wichita
(316) 265-9577
SD, Huron
(605) 352-8616
MN, Lakeville
(952) 469-5267
TX, Houston
(713) 928-2632
MT, Billings
(406) 248-7771
UT, Salt Lake City
(801) 972-4321
WI, Portage
(608) 742-1370
B.I.I. Division
rd
1330 43 Street N.W.
Fargo, ND 58102
Ph: (701) 282-7014
Fax: (701) 282-5865
OFFSHORE WAREHOUSES
CANADIAN WAREHOUSES
B.C., Abbotsford
(604) 864-2665
AB, Edmonton
(403) 962-6991
SK, Regina
(306) 781-2300
Burando Hill
Katanning
W. Australia
011-618-98-214422
Chihuahua, Mexico
011-52-158-90306
John Kerr Equipment Ltd.
Wilcoxholm Farm
Linlithgow, W. Lothian
Scotland
011-441-506-842280
Skovde, Sweden
011-46-500-452651
Naestved, Denmark
011-45-557-29511
ON, Woodstock
(519) 539-0435
ON, Jasper
(613) 283-1758
QC, Dorion
(450) 455-4840
Buhler Manufacturing “a partnership”
1260 Clarence Avenue
Winnipeg, Manitoba R3T 1T2
Ph.: (204) 661-8711
Fax: (204) 654-2503
Toll Free: 888-524-1003
E-mail: info@buhler.com
www.buhler.com
Printed in U.S.A.