Service manual | Bunn 34766.0000S Coffeemaker User Manual

LCA-2
LCA-2A
LCA-2 PC
LCC-2
WER
PO
Y
AD
RE
N
IO
RT
PO
RI
NSE
FI
LL
RE
OP!
ST
ER
T
HO
RT
IN
RN
A
! W
G
IQU
TL
HO
IDS
!
E
AV
NT
ME
E
ISS
ES
UID
LIQ
WAT
DS
AU
CH
INSTALLATION & OPERATING GUIDE
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts
Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, at
www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and
manual updates. For Technical Service, contact Bunn-O-Matic Corporation at 1-800-286-6070.
34766.0000S
06/11 ©2002 Bunn-O-Matic Corporation
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY
Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:
1) All equipment other than as specified below: 2 years parts and 1 year labor.
2) Electronic circuit and/or control boards: parts and labor for 3 years.
3) Compressors on refrigeration equipment: 5 years parts and 1 year labor.
4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis:
parts and labor for 3 years or 30,000 pounds of coffee, whichever comes first.
These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by
it will be commercially free of defects in material and workmanship existing at the time of manufacture and
appearing within the applicable warranty period. This warranty does not apply to any equipment, component or
part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect,
alteration, improper installation or operation, improper maintenance or repair, damage or casualty. This warranty is
conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone
at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by
BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior
authorization from BUNN that the defective equipment is under warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR
ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN
are not authorized to make modifications to this warranty or to make additional warranties that are binding on
BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and
should not be relied upon.
If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its
exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts
and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective
components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace
the equipment or refund the purchase price for the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF
THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S
SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.
In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales,
loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute
equipment, facilities or services, or any other special, incidental or consequential damages.
392, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, BrewWIZARD, BUNN Espress, BUNN
Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the stylized red line, BUNNlink, Bunn-OMatic,
Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design, Cool Froth, DBC, Dr. Brew stylized Dr. design,
Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, iMIX, Infusion Series,
Intellisteam, My Café, PowerLogic, Quality Beverage Equipment Worldwide, Respect Earth, Respect Earth with the stylized leaf and coffee cherry design, Safety-Fresh, savemycoffee.com, Scale-Pro, Silver Series, Single, Smart Funnel, Smart
Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment Worldwide, ThermoFresh, Titan,
A Partner You Can Count On, Air Brew, Air Infusion, Beverage Bar Creator, Beverage Profit Calculator, Brew better, not
bitter., BUNNSource, Coffee At Its Best, Cyclonic Heating System, Digital Brewer Control, Nothing Brews Like a BUNN,
Pouring Profits, Signature Series, Tea At Its Best, Phase Brew, The Horizontal Red Line, trifecta, Ultra, Velocity Brew are
either trademarks or registered trademarks of Bunn-O-Matic Corporation.
2
34766 050511
CONTENTS
Warranty........................................................................... 2
Introduction...................................................................... 3
User Notices..................................................................... 4
Electrical Requirements.................................................... 5
CE Requirements.............................................................. 5
Plumbing Requirements................................................... 6
Initial Set-up..................................................................... 6
Electrical Hook-up............................................................. 6
Plumbing Hook-up............................................................ 6
Setting Dispenser Flow Rate............................................. 7
Selecting the Correct Pump Tubing................................... 8
Operating Controls & Interface......................................... 9
Initial Fill & Heat.............................................................. 10
FlavorGard™ Feature....................................................... 11
Rinse Alarm Feature........................................................ 11
BIB Empty Lockout Feature............................................. 12
Brew Temperature Lockout Feature................................. 12
Programming the Dispenser Flow Rate........................... 13
Loading the Concentrate................................................. 19
Priming the Concentrate Lines........................................ 19
Operating the Pull & Hold Dispenser............................... 20
Operating the Preset Portion Control Dispenser............. 21
Filling Cambros or other large containers....................... 21
Cleaning & Preventive Maintenance................................ 22
Replacing the Pump Tubing............................................ 23
Draining the Hot Water................................................... 24
Troubleshooting.............................................................. 25
Field Calibration of the Concentrate Pumps.................... 30
Dispenser Flow Rate Calibration..................................... 31
Field Calibrating the Hot Water Flow Rate....................... 31
Field Calibrating the Empty BIB Warning......................... 32
Schematic Wiring Diagrams............................................ 33
INTRODUCTION
The Liquid Coffee Ambient Dispenser (LCA-2) and the Liquid Coffee Chilled Dispenser (LCC-2) delivers two
types of coffee made from liquid concentrate plus hot water. The dispenser can be set up for continuous draw
(by the cup) for self-serve applications, or portion-control to fill carafes and decanters for wait staff. Follow the
Concentrate Manufacturer’s Storage and Shelf Life recommendations. Product Flavor Profile is extended with
chilled product storage cabinet featured in the LCC-2.
This dispenser is designed to operate when ambient temperatures are from 32°F (0°C) minimum to 104°F
(40°C) maximum.
3
34766 030508
USER NOTICES
Carefully read and follow all notices on the equipment and in this manual. They were written for your protection. All notices are to be kept in good condition. Replace any unreadable or damaged labels.
As directed in the International Plumbing Code of the
International Code Council and the Food Code
Manual of the Food and Drug Administration (FDA),
this equipment must be installed with adequate
backflow prevention to comply with federal, state
and local codes. For models installed outside the
U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area.
00656.0001
00986.0002
Optional
Wiring
Artwork for P/N:Field
00656.0001
Artwork Rev: A
Drawn: REF
Date: 04/22/10
208-240 V, 25.8 A, 6200 W
1PH, 2-Wire + GND, 60HZ
or
120/208-240 V, 25.8 A, 6200 W
1PH, 3-Wire + GND, 60HZ
To reduce the risk of electric shock,
do not remove or open cover.
No user-serviceable parts inside.
Authorized service personnel only.
Disconnect power before servicing.
28181.0003
37881.0000
11646.0002
00824.0001
REMINDER!
CLEAN AIR FILTER
WEEKLY
AIR FILTER
CLEAN WEEKLY!
(LOCATED UNDER THE DISPENSER)
FILTRO DE AIRE
LIMPIAR
SEMANALMENTE!
RECORDATORIO!
LIMPIAR EL FILTRO DE
AIRE SEMANALMENTE
(LOCATED UNDER THE DISPENSER)
(LOCALIZADO DEBAJO
DEL DISPENSADOR)
(LOCALIZADO DEBAJO
DEL DISPENSADOR)
40054.0000
00824.0002
4
34766 012711
ELECTRICAL REQUIREMENTS
CAUTION: The dispenser must be disconnected from the power source until specified in Electrical Hook-Up.
The LCA-2 and LCC-2 dispensers are supplied with a 120-volt / 15 Amp cord set and require a 2-wire, grounded,
individual branch circuit rated for 120 volts AC, 15 amp, single phase, 60Hz. The mating connector must be
a NEMA 5-15R.
The LCA-2C and LCC-2C dispensers are supplied with a 120-volt / 20 Amp cord set and require a 2-wire,
grounded, individual branch circuit rated for 120 volts AC, 20 amp, single phase, 60Hz. The mating connector
must be a NEMA 5-20R.
These dispensers can be Field Wired for 208 or 240 volt applications. This requires a 2 or 3-wire, grounded,
individual branch circuit rated for 208/240 volts AC, 30 amp, single phase, 60 Hz.
NOTE: The internal terminal block must be rewired for 208/240 applications, (see Optional Field Wiring
Diagram).
FIELD WIRING TERMINAL BLOCK DIAGRAM
Models
without
MasterBLOCK
ON/OFF
Switch
FIELD
WIRING
TERMINAL
DIAGRAM
HEATER RED
HEATER RED
HEATER RED
10A. FUSE - WHITE
10A. FUSE - WHITE
10A. FUSE - BLACK
LIMIT SW. - BLACK
120V A.C.
Fig. 1
208 or
240V A.C.
10A. FUSE - BLACK
Fig. 2
LIMIT SW. - BLACK
10A. FUSE - WHITE
10A. FUSE - BLACK
LIMIT SW. - BLACK
120V A.C.
208 or
240V A.C.
120V A.C.
Fig. 3
For all 208 - 240 Volt Connections: Use No. 10 AWG Wires suitable for 90°C (194°F)
1. Unit shipped per Fig. 1, wired for 120V A.C./2-Wire.
2. For 208 - 240V A.C./2-Wire per Fig. 2: Move both the Red-Heater wire and the White-Fuse wire to the Top Red Terminal as shown.
3. For 120/208 - 240V A.C./3-Wire per Fig. 3: Move the Red Heater wire to the Top Red Terminal as shown.
34960.0000B 11/02 © 2002 BUNN-O-MATIC CORPORATION
FIELD WIRING TERMINAL BLOCK DIAGRAM
Models
withTERMINAL
Master ON/OFF
FIELD
WIRING
BLOCKSwitch
DIAGRAM
RED
TO MASTER
ON/OFF
SWITCH
BLACK
RED
120V A.C.
RED
TO MASTER
ON/OFF
SWITCH
208 or
240V A.C.
BLACK
Fig. 1
TO MASTER
ON/OFF
SWITCH
BLACK
Fig. 2
120V A.C.
208 or
240V A.C.
120V A.C.
Fig. 3
For all 208 - 240 Volt Connections: Use No. 10 AWG Wires suitable for 90°C (194°F)
1. Unit shipped per Fig. 1, wired for 120V A.C./2-Wire.
2. For 208 - 240V A.C./2-Wire per Fig. 2.
3. For 120/208 - 240V A.C./3-Wire per Fig. 3.
34960.0001A 01/07 © 2007 BUNN-O-MATIC CORPORATION
The LCR-2A dispenser is internally wired from the factory for 230 Volts
AC Single Phase 50/60 Hz. It requires a 2-wire, grounded, individual
branch circuit rated for 230 Volts AC.
L2 RED
200, 230
or
230V
A.C.
L1 BLACK
240V A.C.
CE REQUIREMENTS
• This appliance must be installed in locations where it can be overseen by trained personnel.
• For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C.
• Appliance shall not be tilted more than 10° for safe operation.
• An electrician must provide electrical service as specified in conformance with all local and national codes.
• This appliance must not be cleaned by water jet.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given instructions concerning use of this appliance by
a person responsible for its safety.
• Children should be supervised to ensure they do not play with the appliance.
• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel with a special
cord available from the manufacturer or its authorized service personnel in order to avoid a hazard.
• Machine must not be immersed for cleaning.
5
34766 062210
PLUMBING REQUIREMENTS
The dispenser may be connected to a cold or hot water system (140°F Max.) with operating pressure between
20 and 90 psi (138 and 620 kPa) from a 1/2” or larger supply line. A shut-off valve should be installed in the line
before the dispenser. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to
50 psi (345 kPa). The water inlet fitting is 3/8” flare. Dispensers set up to deliver to 1.8 Oz./sec. (53.2 ml/sec)
per dispense tip, require a water supply source that can deliver a minimum of 1.7 gpm (6.4 lpm) at the inlet
fitting. Dispensers set up to deliver 2.6 Oz./sec. (76.9 lpm) per dispense tip, require a water supply source that
can deliver a minimum of 2.4 gpm (9.2 lpm) at the inlet fitting.
NOTE: Bunn-O-Matic recommends 3/8” tubing from the 1/2” water supply line. At least 18 inches of FDA
approved flexible beverage tubing, such as reinforced braided polyethylene or silicone, before the dispenser will
facilitate movement to clean the counter top. Bunn-O-Matic does not recommend the use of a saddle valve to
install the dispenser. The size and shape of the hole made in the supply line by this type of device may restrict
water flow.
As directed in the International Plumbing Code of the International Code Council and the Food Code
Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate
backflow prevention to comply with federal, state and local codes. For models installed outside the
U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area.
INITIAL SET-UP
NOTE: The LCC-2 (Chilled Unit) weighs approximately 80 lbs. (36.3 kg) and the LCA-2 (Ambient Unit) weighs
approximately 70 lbs. (31.8 kg). If necessary, use more than one person when lifting or moving the dispenser.
1.
2.
3.
4.
5.
6.
Locate and remove the information packets and tube kits from top of packaging and set aside.
Remove foam packing and cut around the bottom of box.
Remove the box and the rest of the foam packing.
Open the dispenser door and remove the drip tray and the lower splash guard panel.
Set dispenser on the counter where it is to be used. CAUTION: DO NOT LIFT ON THE DOOR.
Confirm the dispenser is level on the counter.
ELECTRICAL HOOK-UP
CAUTION: Improper electrical installation will damage electronic components.
1. An electrician must provide electrical service as specified in conformance with all local, state and federal
electrical codes.
2. Using a voltmeter, check the voltage and color-coding of each conductor at the electrical source.
3. Connect the dispenser to the power source.
4. If plumbing is to be hooked up later, be sure the dispenser is disconnected from the power source. If plumbing
has been hooked up, the dispenser is ready for Initial Fill & Heat.
PLUMBING HOOK-UP
1. Flush the water line to remove any debris or foreign material.
2. Securely attach the water line to the 3/8” flare fitting, on bottom right side of the dispenser.
3. Turn on the water supply and check for leaks.
NOTE: Water pipe connections and fixtures directly connected to a potable water supply shall be sized, installed,
and maintained in accordance with federal, state, and local codes.
6
34766 062210
SETTING DISPENSER FLOW RATE
The dispenser comes from the factory with flow restrictors in the mix chambers. With the restrictors in place
the dispense rate is about 1.8 oz./sec (53.2 ml/sec) and is used primarily for cup at a time dispensing. The
flow restrictors can be removed to increase the dispense rate to about 2.5 oz./sec (74 ml/sec) for larger volume
dispensing (airpots, carafes, etc.).
NOTE: The hot water FlowRate is fixed at approximately 1.7 oz/sec. and can not be adjusted.
Removing the restrictors:
1. Disconnect the dispenser from the AC power source.
2. Open the Product Cabinet door.
3. Remove the concentrate tube, vent line and grommet from mix chamber ports in side the product cabinet.
4. Remove the two screws that fasten mix chamber to the control panel.
5. Gently pull mix chamber away from dispenser to expose water line connection, (you may have to rotate it
slightly).
6. Disconnect FlavorGard™ sensor wire and hot water tubing from the mix chamber.
7. Remove the flow restrictor from the inlet to the mix chamber.
8. Reconnect FlavorGard™ sensor wire and hot water tubing to the mix chamber.
9. Place mix chamber back into position in the dispenser, (you may have to rotate it slightly) and secure it with
the two screws
10.Reposition the grommet, vent line and pump tubing onto the mix chamber ports.
Caution: Failure to properly replace and secure any of the above components may result leaks and/or cause
damage to the dispenser.
If you changed the Dispenser Flow Rate, you will need to reprogram the dispenser to the new rate, see Programming
the Dispenser.
CAUTION: Failure to reprogram the Dispenser Flow Rates will result in inaccurate Mix Ratios.
Reprogramming the Dispenser Flow Rate:
1. Remove the lower splash guard panel and locate the Programming module.
2. Use the Down Arrow key to enter into the programming function and scroll through the menu’s to the “CAL
LEFT SIDE?” menu and select “YES”.
3. Scroll down to the “CAL LF WTR VOL” menu
4. Use the (+) & (-) keys to enter a volume of 50 Oz. (1478 mL). This will recalibrate the Left dispenser to the
new rate.
5. Scroll down to the “CAL RT WTR VOL” menu
6. Use the (+) & (-) keys to enter a volume of 50 Oz. (1478 mL). This will recalibrate the Right dispenser to the
new rate.
7. Select “Exit” to leave the programming menu.
Note: The default volume of 50 Oz (1478 mL), is the typical Cal Volume for a 2.5 Oz/sec Flow Rate Test, see Field
Calibration of the Concentrate Pumps / Dispenser Flow Rates.
7
34766 073007
SELECTING THE CORRECT PUMP TUBING
There are two pump tube sizes available for use with this dispenser. To determine the correct tubing for you
application, first determine the dispenser flow rate you intend to use, refer to Setting Dispenser Flow Rate. Then
look up the recommended tube size for the mix ratio of your concentrate, refer to the Tube Selection Chart.
TUBE SELECTION CHART
Dispense
Concentrate Ratios
Rate 253035404550556065707580859095100
1.8 Oz/sec. 3/16” I.D. TUBING
1/8” I.D. TUBING
(53 ml/sec.)
2.5 Oz/sec. 3/16” I.D. TUBING
1/8” I.D. TUBING
(74 ml/sec.)
Examples:
1. For a Dispenser Flow Rate of 2.5 Oz./sec (74 mL/sec) and a Mix Ratio of 35:1 – use 3/16” I.D. Tubing.
2. For a Dispenser Flow Rate of 1.8 Oz./sec (53 mL/sec) and a Mix Ratio of 60:1 – use 1/8” I.D. Tubing.
Tube kits can be purchased from BUNN-O-MATIC.
Part # 34727.1000 for 3/16” I.D. Tubing or #34728.1000 for 1/8” I.D. Tubing.
INSTALLING THE PUMP TUBING (Refer to the Tubing Installation Instructions in side the cabinet door for
details.)
1. Loosen the thumbscrew securing the tubing retainer plate to the pump housing. Set it and the retainer plate
aside.
2. Depress the tension screw and remove it from the notch in the pump body, releasing the spring tension on
the pump band.
3. Apply lubricant (BUNN-O-MATIC part number M2531.0001) to the new pump tubing.
4. Insert the tubing onto the mix chamber port and wrap the tubing around the pump rotor, making sure that
the elbow and clamps end up on the bottom side of the pump body.
5. Close the compression band reinsert the tension screw into the notch in the pump housing.
6. Replace the tubing retainer plate and tighten the thumbscrew.
7. Reconnect bag connector to the product box.
8. Repeat steps 1 through 7 for the other pump.
9. Prime the pumps. Refer to Priming the Concentrate Lines section.
Thumbscrew
2.0”
Tension
Screw
Remove Retaining Plate
2.0”
Lubricate between arrows
Release Spring Tension
Remove Tubing
Lubricate New Tube
Tension Screw
Tube Clamp
Install New Tubing
Completed Installation
8
34766 112502
OPERATING CONTROLS AND INTERFACE
1a.Dispense Handles: Pull and Hold to dispense product.
1b.Dispense Switches: Push and Release to dispense product for Portion Control Models.
2. Stop Switch: Momentary switch stops all dispense functions.
3a.Hot Water Switch: Push and Hold switch to dispense hot water from the center dispense tip.
3b.Push and Release switch for Portion Control Models.
4. Alternate Portion Control Switch: Momentarily pushed to select the Alternate Portion Control Volume #2.
5. Function Selector Switch: Allows the user to set the dispenser into different dispensing modes.
a. Rinse: Dispenses hot water only- Flushes the mix chamber and dispense tip.
b. Prime: Dispenses concentrates only – Primes the concentrate pump.
c. Normal: Normal dispense mode - Dispenses mixed product (concentrate and water).
6. Mode Selector Switch: Allows the user to set the dispenser into different operating modes.
a. Run: Normal operating position.
b. Off: Turns off all functions including tank heater and chiller.
WARNING - The OFF Mode does not remove AC power from the dispenser. Disconnect power source before
servicing the dispenser
c. Night: Anti-pilfering mode that disables dispensing, but keeps the tank heater and chiller (if applicable)
operational.
7. Door Interlock Switch: Unit will not dispense product if the door is open.
8. Power LED: Red - illuminates when AC power is applied to dispenser.
9. Ready LED: Green - illuminates when the water is at the preset ready temperature.
10.Portion LED: Yellow - illuminates when the portion dispense option has been selected, (5 second delay).
11.Rinse LED: Yellow - illuminates when the optional preset rinse alarm time has elapsed.
12.Left Refill LED: Yellow - illuminates when the Left Concentrate BIB needs replaced.
13.Right Refill LED: Yellow - illuminates when the Right Concentrate BIB needs replaced.
14.Programming Keypad: Used in conjunction with the LCD display to program and calibrate the dispenser to
customer specific requirements. (Located behind the splash guard panel)
15.LCD Display: Displays programming menus and fault messages. (Located behind the splash guard panel)
5
6
7
8
9
10
1
4
BUNN ICED COFFEE
AMBIENT UNIT
12
15
14
11
13
2
3
9
34766 120105
INITIAL FILL & HEAT
1.Select Normal on the Function Selector Switch and Run on the Mode Selector Switch.
2. Confirm the water supply is on.
3. Connect the dispenser to the power source. The Red POWER LED will illuminate and water will begin flowing
into the tank. The dispenser will automatically stop filling when the tank is full. The dispenser will not begin
heating the water until after the tank is filled. Dispenser models with product chillers will begin to cool the
cabinet at this time.
4. The Green READY LED will illuminate when the tank temperature reaches the preset ready temperature.
Note: The time required to heat the water initially will vary depending on the AC Power supplied to the
dispenser.
While the tank is heating, the dispenser may be readied for use as described in Programming Functions & Basic
1
1
Operations.
3
4
10
34766 112502
FlavorGard™ Feature
FlavorGard™ is a patented feed back control loop that monitors the mixed product and adjusts the concentrate
delivery rate to maintain a consistent mix profile, i.e. Flavor Profile. The system consists of a conductance probe
mounted in the final stages of the mixing chamber, a metering pump with RPM sensor and a digital controller.
Once you have completed the installation of the dispenser, entered the desired mix ratio for your concentrate,
dispensed several cups of the mixed product, and are satisfied with the Flavor and Strength being delivered,
simply enable FlavorGard™, (refer to FlavorGard™ in Programming the Dispenser).
The dispenser will automatically calibrate the system to all the factors that make up your particular mix profile,
(e.g. water source, filtration system, Brand of concentrate and mix ratio selected, etc.).
NOTE: It is very important that you have dispensed enough product to insure that the dispenser is fully functional
and you are satisfied with the Flavor Profile of the mix product before enabling FlavorGard™.
Once FlavorGard™ is enabled, the dispenser will continuously monitor the mix product as it is being dispensed
and adjust the metering pump speed to maintain a consistent mixed product, thus eliminating factors such as
(settling of the concentrate, tube wear, viscosity changes, liming, etc.).
The system is designed to work with in the range of variations that can be caused by these factors. The factory
preset range is (+/- 10 %) and is adjustable to a Max of (+/- 15%). This insures that the FlavorGard™ system is
not responding to factors that cannot be corrected by minor adjustments to the speed of the metering pump,
(e.g. kinked hoses, low water pressure, severely worn tubes, empty BIB’s, etc).
NOTE: Changes to Concentrate Ratios or Dispenser Flow Rates will automatically disable FlavorGard™.
You will need to re-enable FlavorGard™, once you are satisfied with the new Flavor Profile.
Rinse Alarm Feature
Periodic rinsing of the mix chambers and dispense tips is essential for proper maintenance and optimum
performance of the dispenser. The automated Rinse Alarm feature has three levels of operation, Disabled, Warning
Only and Warning with Brew Lockout, see chart for details.
Alarm Level Selected
Alarm Mode
DisabledNone
Warning Only
Rinse LED will come on 4 hrs prior to the selected time interval
and remain on until the Rinse procedure has been performed. The dispenser will
continue to serve product.
Warning w/ Brew Lockout
Rinse LED will come on 4 hrs prior to the selected time interval and remain on
until the Rinse procedure has been performed. The dispenser will Lockout and
not continue to serve product once the selected time interval has elapsed.
NOTE: The time interval between Rinses is adjustable from 8 to 24 hrs.
The dispenser is shipped with the automated Rinse Alarm disabled, (No Alarm). It is up to the user to determine the
Rinse time interval and the level of warning required, based on their application and maintenance procedures.
To enable the automated Rinse Alarm feature, refer to RINSE ALARM ? in Programming the Dispenser.
11
34766 050103
Rinse Procedure:
1. Open the cabinet door and select Rinse on the Function Selector switch – close the door.
2. Place a 2 Liter (1/2 Gal) container under the Left dispense tip.
3. Activate the Left dispenser until water flow stops automatically, approximately 20 sec.
4. Repeat Steps 2 & 3 for the Right dispense tip.
The Rinse LED will turn OFF, when the Rinse procedure has been satisfied for both sides.
5. Open the cabinet door and select Normal on the Function Selector switch – close the door.
1
5
BIB Empty Lockout Feature
The dispenser can be set to not dispense product when the concentrate BIB is empty. To enable this feature, first
calibrate the Empty BIB Threshold (refer to Field Calibrating the Empty BIB Warning). Then enable the BIB Empty
Lockout feature (refer to the BIB Empty Lockout menu in Programming the Dispenser). The dispenser will now
Lockout dispensing and flash the Right or Left “REFILL LED” corresponding to the empty BIB. Once the BIB has
been replaced, PRIME the concentrate line (refer to Priming the Concentrate Lines) and then dispense mixed
product until the “REFILL LED” goes out. NOTE: If the dispenser fails to clear the BIB Empty Lockout, repeat the
Priming operation a second time to insure the concentrate is flowing properly.
Brew Temperature Lockout Feature
The dispenser can be set to not dispense product if the hot water is not up to the preset READY temperature. To
enable this feature set the READY temperature to the minimum allowable dispense temperature. Then enable the
Brew Lockout feature, refer to READY TEMP and BREW LOCKOUT, in Programming the Dispenser.
12
34766 042304
PROGRAMMING THE DISPENSER
Remove the lower splash guard assembly to access the digital programming module with LCD display.
Press the Down Arrow key to inter the programming menu.
Use the Up and Down Arrow keys to scroll through the menu screens.
Select Exit to leave the programming function and return to normal operations.
NOTE 1: Flashing menu items indicate which selection is active.
NOTE 2: Values shown below are the factory default values for English units.
NOTE 3: Values in [X - X] are the Min. and Max. for that function.
MENU SCREEN ACTION 
TANK TEMP XXX
AMBIENT UNIT
DESCRIPTION
Use the Down Arrow Key to enter Normal Display for LCA models, (No Chiller)
Programming Functions
TANK TEMP XXX
CABINET TEMP XX
 
L DISPENSE RATIO
(-) 35:1 (+)
Use the Down Arrow Key to enter Normal Display for LCC models, (with Chiller)
Programming Functions
 
Use the (+) or (-) buttons to Enter the desired Mix Ratio for the concentrate
adjust the Mix Ratio
used in the Left dispenser. [20:1 - 100:1]
SET LF TUBE SIZE
1/8 EXIT 3/16
Select tube size.
R DISPENSE RATIO
(-) 35:1 (+)
Use the (+) or (-) buttons to Enter the desired Mix Ratio for the concentrate
adjust the Mix Ratio
used in the Right dispenser. [20:1 - 100:1]
SET RT TUBE SIZE
1/8 EXIT 3/16
Select tube size.
Enter Pump Tube Size to be used in the Left
metering pump, (see Tube Selection Chart)
Enter Pump Tube Size to be used in the Right
metering pump, (see Tube Selection Chart)
FLAVOR GUARD ?
NO EXIT YES
Select (YES) to activate. Select Select Yes, if you are ready to calibrate the Flavor
(NO) to deactivate.
Guard sensor. Select NO, if you do not wish to
use this feature, (see Flavor Guard)
If NO - go to LF DISP VOLUME menu.
LF TASTE OK ?
NO EXIT YES
FIND LF TARGET
PULL DISPENSE
RT TASTE OK ?
NO EXIT YES
 FIND RT TARGET
PULL DISPENSE
Select (YES) or (NO)
Select YES, if you have dispensed several cups
and are satisfied with the Left dispenser flavor.
Select NO, if you have not run taste test.
Place a 16 Oz. (500 mL) cup Calibrates the Left FlavorGard™ sensor to the
under the Left dispense tip, then current MixProfile. The dispenser will shut OFF
activate the Left dispenser
automatically when finished.
Select (YES) or (NO)
Select YES, if you have dispensed several cups
and are satisfied with the Right dispenser flavor.
Select NO, if you have not run taste test.
Place a 16 Oz. (500 mL) cup Calibrates the Right FlavorGard™ sensor to the
under the Right dispense current MixProfile. The dispenser will shut OFF
tip, then activate the Right automatically when finished.
dispenser
13
34766 042304
MENU SCREEN ACTION 
LOCK
FLAVOR ?
EXIT YES
FLAVORS LOCKED
EXIT
DESCRIPTION
Select (YES) or (EXIT)
Select YES, to Lock In sensor calibration. NOTE:
Display will return to “Find LF Target” if sensor
calibration is out of range.
NONE
Confirms that sensor calibration was in range and
accepted. Scroll down to continue.
Portion Control Settings for Pull and Hold Dispensers
For Portion Control Dispensers (LCA-2 PC, LCA-2C PC, LCA-2A PC) go to Full Time Portion Control Settings
LF DISP VOLUME
(-) 4.0oz (+)
Use the (+) or (-) buttons Set the volume to be dispensed during a Left
to adjust the Left portion Portion controlled dispense to: [0 - 640 Oz.] or
volume
[0 - 18.93L]
RT DISP VOLUME
(-) 4.0oz (+)
Use the (+) or (-) buttons Set the volume to be dispensed during a Right
to adjust the Right portion Portion controlled dispense to: [0 - 640 Oz.] or
volume
[0 - 18.93L]
Full Time Portion Control Settings
LF DISP VOLUME 1
(-) 4.0oz (+)
Use the (+) or (-) buttons Set the desired portion control volume to be
to adjust the Normal Left dispensed during a Normal Left dispense to: [0
volume
- 640 Oz.] or [0 - 18.93L]
LF DISP VOLUME 2
(-) 0.0oz (+)
Use the (+) or (-) buttons Set the desired portion control volume to be
to adjust the Alternate Left dispensed during a Alternate Left dispense to:
volume
[0 - 640 Oz.] or [0 - 18.93L]
RT DISP VOLUME 1
(-) 4.0oz (+)
Use the (+) or (-) buttons Set the desired portion control volume to be
to adjust the Normal Right dispensed during a Normal Right dispense to:
volume
[0 - 640 Oz.] or [0 - 18.93L]
RT DISP VOLUME 2
(-) 0.0oz (+)
Use the (+) or (-) buttons to Set the desired portion control volume to be
adjust the Alternate Right dispensed during a Alternate Right dispense to:
volume
[0 - 640 Oz.] or [0 - 18.93L]
WATER DISP VOL 1
(-) 0.0oz (+)
Use the (+) or (-) buttons to Set the desired portion control volume to be
adjust the Normal Hot Water dispensed during a Normal Hot Water dispense:
volume
[0 - 640 Oz.] or [0 - 18.93L]
WATER DISP VOL 2
(-) 0.0oz (+)
Use the (+) or (-) buttons to Set the desired portion control volume to be
adjust the Alternate Hot Water dispensed during a Alternate Hot Water dispense:
volume
[0 - 640 Oz.] or [0 - 18.93L]
14
34766 120105
MENU SCREEN ACTION 
DESCRIPTION
TANK TEMP 180
(-) EXIT (+)
Use the (+) or (-) buttons to Sets the water Tank temperature [120 - 200°F]
adjust the target Temp.
or [49 - 93°C]
READY TEMP 175
(-) EXIT (+)
Use the (+) or (-) buttons to Sets the hot water Ready temperature. Typically
adjust the target Temp.
set to the minimum desired dispense temp.
CABINET TEMP 65
(-) EXIT (+)
Use the (+) or (-) buttons to LCC Models Only: Sets the Chilled Cabinet target
adjust the target Temp.
temperature [50 - 75°F] or [4 - 24°C]
LF PRODUCT DISP
.0GAL RESET?
Select (RESET) to clear total Selecting Reset will clear the Current accumulated
volume of concentrate dispensed through the Left
dispenser. Gal (Liters)
LF PRODUCT DISP
.0GAL
RT PRODUCT DISP
.0GAL RESET?
RT PRODUCT DISP
.0GAL
NONE
Displays the Total accumulated volume of
concentrate dispensed through the Left dispenser.
Not Re-settable. Gal (Liters)
Select (RESET) to clear total Selecting Reset will clear the Current accumulated
volume of concentrate dispensed through the
Right dispenser. Gal (Liters)
NONE
Displays the Total accumulated volume of
concentrate dispensed through the Right
dispenser. Not Re-Settable. Gal (Liters)
The following functions can be Password Protected. If you wish to prevent others from accessing these
functions, enter a 4 digit code of your choice. Record your password code [_ _ _ _], as you will need it
to access these functions in the future.
ENTER PASSWORD
(-)
0 (+)
Use the (+) or (-) buttons to Enter the access Code to view the remaining
enter password.
functions. Factory Default = 0.
SET PASSWORD ?
(-)
0 (+)
Use the (+) or (-) buttons to Enter your own Code to prevent access to the
change the password.
remaining functions. [0 to 9999]
SELECT UNITS
ENG EXIT METRIC
Select the preferred units
Used to select the preferred units of measurement.
(Oz., Gal, deg F) or (mL, L, deg C)
CHILLED UNIT ?
NO EXIT YES
Select (YES) or (NO)
LCA Models without Chiller select (NO)
LCC Models with Chiller select (YES)
RINSE ALARM ?
NO EXIT YES
Select (YES) or (NO)
Selecting Yes will enable the Rinse Alarm function,
(see Rinse Alarm)
If NO - go to BIB EMPTY LOCKOUT menu.
15
34766 120105
MENU SCREEN ACTION 
RINSE TIME ?
(-) 12 Hrs (+)
DESCRIPTION
Use the (+) or (-) buttons to Enter the desired time between required Rinse
adjust Rinse Alarm delay
Cycles in hours, [8 - 24 hrs.]
RINSE LOCKOUT ?
NO EXIT YES
Select (YES) to enable
Select YES to Lockout dispensing until the Rinse
Alarm has been cleared. Default is NO
BIB EMPTY LOCKOUT
NO EXIT YES
Select (YES) to enable
Select YES to Lockout dispensing until the
Concentrate BIB has been replaced. Default is
NO
Select (YES) to enable
Select YES to Lockout dispensing until the hot
water tank is at READY Temp. Default is NO
BREW LOCKOUT ?
NO EXIT YES
DLY REPEAT DISP
(-) 0 SEC (+)
Use the (+) or (-) buttons to Enter the desired time delay before allowing the
adjust the Delay Time
next dispense to take place, [0 - 10 sec.]
The following functions are for diagnostic and troubleshooting purposes and typically do not have to be
adjusted. Contact your local service agent for assistance before making changes to these functions.
CAL LEFT SIDE ?
EXIT YES
Select (YES) to enable
Selecting Yes will enable the Left Dispenser
Calibration routine, (see Field Calibration before
attempting to calibrate the dispenser).
If NO - go to CAL RIGHT SIDE menu.
CAL LEFT PUMP ?
PULL DISPENSE
Place a 50 mL (#34843.1000) The Left Pump will dispense concentrate for 20
graduated cylinder under the seconds, then shut off automatically. Collect and
Left dispense tip, then activate measure the concentrate dispensed.
the Left Dispenser
CAL LF PUMP VOL
(-) 43mL (+)
Use the (+) or (-) buttons to Enter the volume of concentrate measured from
enter volume collected
the Left Pump in mL, (not Oz.) regardless of
Preferred Units selected.
CAL LF WTR FLOW ?
PULL DISPENSER
Place a 64 Oz. (2000 mL) The Left Dispenser will dispense hot water for 20
container under the Left seconds, then shut off automatically. Collect and
dispense tip, then activate the measure the water dispensed.
Left Dispenser
CAL LF WTR VOL
(-) 36.0OZ (+)
Use the (+) or (-) buttons to Enter the volume of the water measured from the
enter volume collected
Left dispenser in Oz. (mL).
CAL LEFT SIDE ?
EXIT YES
CAL RIGHT SIDE ?
EXIT YES
NONE
Scroll down to bypass this screen.
Select (YES) to enable Selecting Yes will enable the Right Dispenser
Calibration routine.
Calibration routine, (see Pump Calibration) prior
to calibrating the dispenser.
16
34766 120105
MENU SCREEN ACTION 
DESCRIPTION
If NO - skip to next menu.
CAL RIGHT PUMP ?
PULL DISPENSER
Place a 50 mL (#34843.1000) The Right Pump will dispense concentrate for
graduated cylinder under 20 seconds, then shut off automatically. Collect
the Right dispense tip, then and measure the concentrate dispensed.
activate the Right Dispenser
CAL RT PUMP VOL
(-) 43mL (+)
Use the (+) or (-) buttons to Enter the volume of concentrate measured from
enter volume collected
the Right Pump in mL(not Oz.) regardless of
Preferred Units selected.
CAL RT WTR FLOW
PULL DISPENSER
Place a 64 Oz. (2000 mL) The Right Dispenser will dispense hot water for
container under the Right 20 seconds, then shut off automatically. Collect
dispense tip, then activate the and measure the water dispensed.
Right Dispenser
CAL RT WTR VOL
(-) 36.0OZ (+)
Use the (+) or (-) buttons to Enter the volume of the water measured from the
enter volume collected
Right dispenser in Oz. (mL)
CAL RIGHT SIDE ?
EXIT YES
NONE
Scroll down to bypass this screen.
For Portion Control Dispensers (LCA-2 PC, LCA-2C PC, LCA-2A PC) only
CAL HOT WTR FLO ?
PULL DISPENSE
Place a 64 Oz. (2000 mL) The Hot Water Dispenser will dispense for 20
container under the Hot Water seconds, then shut off automatically. Collect and
dispense tip, then activate the measure the water dispensed.
Hot Water Dispenser
CAL HOT WTR VOL
(-) 34.0OZ (+)
Use the (+) or (-) buttons to Enter the volume of the water measured from the
enter volume collected
Hot Water Dispenser in Oz. (mL)
XXX CAL -> XXX
(-) TankTemp (+)
Use the (+) or (-) buttons to Adjust the display reading to match a calibrated
adjust temperature reading probe inserted next to the Tank Sensor, °F (°C).
FlvrGrdRange 10%
(-) EXIT (+)
Use the (+) or (-) buttons to Used to set the maximum adjustment the Flavor
adjust % value
Guard feature is allowed to make, [3 - 15%].
LfFlvrGrdTargets
RPM XXX-CON XXX
NONE
Displays the Left Dispenser target RPM and
Conductance Reading, (Diagnostics Only)
RtFlvrGrdTargets
RPM XXX-CON XXX
NONE
Displays the Right Dispenser target RPM and
Conductance Reading, (Diagnostics Only)
17
34766 120105
MENU SCREEN ACTION 
DESCRIPTION
BIB EMPTY -> 500
(-) EXIT (+)
Use the (+) or (-) buttons to Used to set the Conductance Threshold for the
adjust empty BIB threshold Empty BIB warning. Default is 500
XX REFILL -> 155
(-) EXIT (+)
Use the (+) or (-) buttons to Used to set the Conductance Threshold for the
adjust Refill threshold
Tank Refill Probe.
WTR START DELAY
(-) .15SEC (+)
Use the (+) or (-) buttons to Dispense Valve ON Delay. Eliminates weak mix
adjust delay time
at the beginning of a dispense.
WTR STOP DELAY
(-) .15SEC (+)
Use the (+) or (-) buttons to Dispense Valve OFF Delay. Flushes the mix
adjust delay time
chamber at the end of a dispense.
TEST LED’S ?
NO EXIT YES
Select (YES) or (NO)
LED diagnostics. Selecting YES will light all Front
Door LED’s.
TEST SWITCHES ?
UseSwitchToTest
NONE
Switch Diagnostic: Activate switches separately to
test. Display will indicate which Switch has been
activated. NOTE: Door Interlock switch must be
held closed.
TEST REFILL ?
EXIT YES
Momentarily depress (YES)
Refill Valve Diagnostic: Press YES to momentarily
energize the Solenoid. CAUTION: Inlet Valve will
open and water will flow, if connected and turned
ON.
TEST HEATER ?
EXIT YES
Momentarily depress (YES)
Tank Heater Diagnostic: Press YES to momentarily
energize the Tank Heater Circuit.
CAUTION: AC power will be applied to the Tank
Heater Circuit.
ENTER ASSET #
(-) 000000 (+)
SERIAL #
LCA 0000000
Use the (+) or (-) buttons to Allows the user the option of entering an Asset
adjust the ASSET NUMBER Number. Default is 000000
NONE
Displays the manufacture’s Serial Number (should
be identical to the Serial Number on the machine
Data Plate)
VIEW FAULTS?
(-) EXIT (+)
Select (+) to view Fault This unit stores the last 3 Fault Conditions in
Conditions
memory for diagnostic purposes.
LATEST FAULT
NO FAULTS
Use (+) or (-) to scroll through Displays up to 3 FAULT Conditions or NO FAULTS,
the Faults
if nothing has failed since the last “Reset Factory
Defaults”.
FACTORY DEFAULTS
NO
YES
Select (YES) or (NO)
CAUTION: Selecting YES will RESET all
Programming Functions to the Factory Default
settings. NOTE: On LCC Models the Chiller will
have to be reset to the ON condition, (see Chilled
Unit programming function).
18
34766 073007
LOADING THE CONCENTRATE
1. Thoroughly mix concentrate by vigorously shaking the product Bag-In-Box (BIB).
2. Pull the BIB connector through the hole provided in the box and place it on the drip tray with the connector
facing up. (See Fig. 1)
3. Open the dispenser door and locate the appropriate left or right BIB Adapter fitting.
4. Pull the Adapter fitting down and connect it to the BIB. (See Fig. 2)
5. Place the BIB upright in the machine, rotating it into position with the connector facing forward.
6. Rotate the BIB Adapter to avoid sharp bends in the tubing and allow it to be routed between the two
pumps.
Refer to the Tube Installation Decal on the door for proper routing. (See Fig. 3)
7. Close the cabinet door.
Fig. 1
Fig. 2
Fig. 3
PRIMING THE CONCENTRATE LINES
1. Open the dispenser door.
2. Load concentrate per instructions in the section titled Loading the Concentrate.
3.Select Prime on the Function Selector Switch and Run on the Mode Selector Switch.
4. Close the dispenser door.
5. Place a container under the appropriate dispense tip.
6. Activate the appropriate dispenser until concentrate flows from the dispense nozzle. Priming may take 5 to
10 seconds.
7. Open the dispenser door, select Normal on the Function Selector Switch, and then close door.
Note: Concentrate may continue to drip out of dispense tip. The user may wish to run a Rinse Cycle (refer to
Rinsing) after Priming the dispenser to clean out the remaining concentrate.
7
3
3
19
34766 042304
OPERATING THE PULL & HOLD DISPENSER
(Models LCA-2, LCA-2C, LCA-2A, LCC-2, LCC-2C, LCC-2A)
Set the Function Selector Switch to Normal and the Mode Selector Switch to Run.
1. Pull and Hold Dispense Mode (Cup at a time)
a. Place cup on the cup tray beneath the desired dispensing tip. For a large container, flip the cup tray up
and place the container on top of the drip tray.
b. Pull and Hold the corresponding dispense handle until the cup or other container is full.
c. Remove cup or container.
2. Portion Dispense Mode (Preset volume dispensing) Refer to Programming Functions on how to set this
volume.
a. Place the appropriate size container beneath the desired dispensing tip. For large containers, flip the cup
tray up and place the container on top of the drip tray.
b. Momentarily press the Portion Switch. The Portion LED will illuminate for 5 seconds after the Portion
Switch is pressed.
c. Momentarily pull the corresponding dispense handle, then release. If the user waits longer than 5 seconds
to pull the handle, the dispenser will default back to the Pull & Hold Mode. Portion Dispense Mode can
be disabled at any time during the portion dispense by either momentarily pulling the Dispense Handle
again or pressing the Stop button.
d. Wait for container to fill and the dispenser to quit dispensing, then remove container.
3. Hot Water Dispense
a. Place container under the hot water dispenser (center of machine). For large containers, flip the cup tray
up and place the container on top of the drip tray.
b. Push and hold the Hot Water Switch until the water reaches the desired level, then release.
c. Remove container.
Filling Cambros or other large containers:
The dispenser is designed primarily for cups or other small containers that will fit under the dispense tips.
However, it may be used to fill larger containers (up to 2 Gal) by use of an extension hose on the dispense tip.
Removing the Flow Restrictors will increase the dispenser flow rate to 2.5 Oz/sec. (74 mL/sec.) and reduce the
time to fill larger containers, (see Setting Dispenser Flow Rate.)
Care must be taken to insure that the mixed product flows freely from the dispense tip into the container.
1. Use a 5/8” I.D. or larger, NSF (National Sanitation Foundation) approved hose.
2. Use as short a hose as possible with no loops, bends or kinks in it.
3. Insure that the outlet of the hose is below the dispense tip and that the mixed product flows freely into the
container
A properly sized and positioned hose will not run full or back up into the dispense tip. Failure to follow these
directions can alter the mix ratio and/or cause flooding of the vent tube.
NOTE: The temperature of the product being dispensed will start to drop after ~2 gal. continuous draw.
Recovery time will be dependent on the temperature of the supply water and the voltage at which the heater
coil is being operated.
34766 042304
20
OPERATING THE PRESET PORTION CONTROL DISPENSER
(Models LCA-2 PC, LCA-2C PC, LCA-2A PC)
Set the Function Selector Switch to Normal and the Mode Selector Switch to Run.
Dispensing Preset Portions of Coffee or Hot Water
1. Primary Volume Portion Dispense Mode. (Volume 1) Refer to Programming Functions on how to set this
amount.
a. Place cup on the cup tray beneath the desired dispensing tip. For a large container, flip the cup tray up
and place the container on top of the drip tray.
b. Momentarily press the appropriate dispense switch. The dispenser will automatically dispense the beverage
at the preset amount. Allow the mix chamber to drain at the end of the cycle.
c. Remove cup or container.
2. Alternate Volume Portion Dispense Mode. (Volume 2) Refer to Programming Functions on how to set this
volume.
a. Place the appropriate size container beneath the desired dispensing tip. For large containers, flip the cup
tray up and place the container on top of the drip tray.
b. Momentarily press the Portion Switch. The Portion LED will illuminate for 5 seconds after the Portion
Switch is pressed.
c. Momentarily press the corresponding Dispense Switch. If the user waits longer than 5 seconds to push
the switch, the dispenser will default back to the Primary Volume preset amount. Alternate Portion
Dispense Mode can be disabled at any time during the portion dispense by either momentarily pushing
the Dispense Switch again or pressing the Stop button.
d. Wait for the container to fill and the dispenser to quit dispensing, then remove the container.
Push and Hold Dispensing of Coffee or Hot Water
Push and Hold Dispense Mode. See Programming Functions on how to set the Preset Volume to Zero.
a. Place cup on the cup tray beneath the desired dispensing tip. For a large container, flip the cup tray up
and place the container on top of the drip tray.
b. Push and hold the corresponding dispense switch until the container is full.
c. Remove cup or container.
Filling Cambros or other large containers:
The dispenser is designed primarily for cups or other small containers that will fit under the dispense tips.
However, it may be used to fill larger containers (up to 5 Gal) by use of an extension hose on the dispense tip.
Removing the Flow Restrictors will increase the dispenser flow rate to 2.5 Oz/sec. (74 mL/sec.) and reduce the
time to fill larger containers, (see Setting Dispenser Flow Rate.)
Care must be taken to insure that the mixed product flows freely from the dispense tip into the container.
1. Use a 5/8” I.D. or larger, NSF (National Sanitation Foundation) approved hose.
2. Use as short a hose as possible with no loops, bends or kinks in it.
3. Insure that the outlet of the hose is below the dispense tip and that the mixed product flows freely into the
container
A properly sized and positioned hose will not run full or back up into the dispense tip. Failure to follow these
directions can alter the mix ratio and/or cause flooding of the vent tube.
NOTE: The temperature of the product being dispensed will start to drop after ~2 gal. continuous draw. Recovery
time will be dependent on the temperature of the supply water and the voltage at which the heater coil is being
operated.
21
34766 120105
CLEANING & PREVENTATIVE MAINTENANCE
General Cleaning and Sanitizing Procedures
Note: The BUNN® Liquid Coffee Dispenser incorporates a “user selectable” rinse reminder feature, which lights
the Rinse LED on the front panel and disables dispensing when it is time to rinse. See Programming Functions
to activate this feature.
Daily: RINSING
1. Open the dispenser door.
2.Select Rinse on the Function Selector Switch and Run on the Mode Selector Switch.
3. Close the dispenser door.
4. Place a 1/2 gal (2 liter) container under the appropriate dispense nozzle or nozzles.
5. Activate the Dispenser of the appropriate side or sides for approximately twenty seconds or until the hot
water is clear or has no concentrate coloring in it.
6. Open the dispenser door, select Normal on the Function Selector Switch, and then close door.
Note: To clear the “Rinse” alarm, activate each dispenser until the flow stops automatically (approx. 20 seconds
for each tip). The “Rinse” alarm LED will turn off when the Rinse Procedure has been satisfied for both sides.
Daily: PARTS WASHING
1. Remove and wash the drip tray, drip tray cover, and cup tray in a mild detergent solution. Rinse
thoroughly.
2. Wipe splash panel, area around dispense nozzles, door, and cabinet with a clean damp cloth.
Weekly: SANITIZING
1. Open the dispenser door.
2.Select Prime on the Function Selector Switch and Run on the Mode Selector Switch.
3. Remove the bag connector from the product box and disassemble or prop open the internal valve to allow
free flow of product through the connector. NOTE: Cutting the mating fittings from an empty bag makes an
excellent “free flowing” connector for this purpose.
4. Place the bag connector into a one-gallon (3.8 liter) container of warm soapy tap water 140°F (60°C).
5. Place an empty container under dispense tip and activate the corresponding Dispenser until the clean soapy
water is dispensed from the dispense tip.
6. Repeat steps 4 and 5 with warm tap water 140°F (60°C) to rinse the soapy water from the pump tubing.
Continue dispensing until the water is clear, and no soapy water is being dispensed.
7. Prepare 2.5 gallons (9.46L) of sanitizing solution by dissolving 1 packet of Kay 5 sanitizer into 2.5 gallons
(9.46L) of 120°F (48.9°C) water to ensure 100 ppm of available chlorine.
8. Again, repeat steps 4 and 5 with the sanitizing solution. Once sanitizing solution is visible, continue to dispense
for 1 minute. Release handle and allow solution to sit for 5 minutes.
9. After soaking for 5 minutes, activate the dispense switch a second time, this time for 2 minutes. After 2
minutes, release the dispense switch.
10.Repeat step 6 to flush out the sanitizing solution from the pump tubing.
11.Remove the mating connector from the bag connector.
12.Reattach the bag connector to product box.
13.Select Normal on the Function Selector Switch and Run on the Mode Selector Switch.
14.Activate the Dispenser until concentrate/water mixture appears. Then dispense one 12 ounce (354.9 ml) glass
of concentrate/water mixture and discard.
15.Repeat steps 1 through 14 for other dispense head.
16.Wipe internal and external surfaces with a clean, damp cloth.
22
34766 070709
PREVENTIVE MAINTENANCE
Bunn-O-Matic Corporation recommends that preventive maintenance be performed at regular intervals. Maintenance
should be performed by a qualified service technician. For Technical Service, contact Bunn-O-Matic® Corporation at
1-800-286-6070.
NOTE: Replacement parts or service caused by failure to perform required maintenance is not covered by warranty.
Replace pump hoses every 6-Months or as needed.
®
REPLACING THE PUMP TUBING
The pumps and tubing used in the dispenser are designed to give maximum performance and long life. However,
the tubes are a wear item and must be replaced periodically. How long the tubes last is dependent on usage and
properties of the concentrate. Excessive wear will reduce the output of the pumps resulting in a weak mixed
beverage. Bunn-O-Matic recommends replacing the Pump Tubing a minimum of once every 6 months or
sooner if warranted.
Refer to the Tube Replacement Instruction on the Cabinet door for details.
1. Rinse the pump tubing with warm tap water (Refer to steps 1 - 5 of the Weekly Sanitizing instructions) prior
to removing the tubes to avoid concentrate spills.
2. Loosen the thumbscrew securing the tubing retainer plate to the pump housing. Set it and the retainer plate
aside.
3. Depress the tension screw and remove it from the notch in the pump housing, releasing the spring tension
on the pump band.
4. Open the compression band and gently pull the pump tube from around the pump’s rotor.
5. Inspect the pump bands for signs of wear. Replace if necessary.
6. Apply lubricant (BUNN-O-MATIC part number M2531.0001) to the new pump tubing’s rotor side.
7. Insert the tube onto the mix chamber port, then wrap the new tubing around the pump rotor, making sure
that the elbow and clamps end up on the bottom side of the pump housing.
8. Depress the tension screw and insert it in the notch in the pump body, reapplying spring tension on the pump
band.
9. Replace the tubing retainer plate and tighten the thumbscrew.
10.Repeat steps 1 through 9 for the other pump.
Note: Replacement Tube/Adapter Kits can be purchased from BUNN-O-MATIC.
Thumbscrew
2.0”
Tension
Screw
Remove Retaining Plate
2.0”
Lubricate between arrows
Release Spring Tension
Remove Tubing
Lubricate New Tube
Tension Screw
Tube Clamp
Install New Tubing
Completed Installation
23
34766 031010
DRAINING THE HOT WATER TANK
CAUTION: The dispenser must be disconnected from the power source throughout these steps.
1. Disconnect the dispenser from the power source.
2. Shut off and disconnect the incoming water supply.
3. Remove the front splash panel.
4. Pull out drain tube to empty into a sink or a container with a minimum of five-gallon capacity.
5. Make sure drain clamp is closed. Then, remove drain plug.
6. Direct tube into sink or container and open drain clamp. Continue draining tank until ALL of the water is out.
Be very careful with the draining water because it can be very hot.
7. Close drain clamp, insert drain plug, place drain tube back into machine, and replace splash panel.
Note: The dispenser must be refilled using the Initial Fill & Heat steps before reconnecting the power source.
24
34766 112502
Troubleshooting
A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems
encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic
Technical Service Department.
• Only qualified service personnel should perform inspection, testing, and repair of electrical equipment.
• Shorting the terminals or the application of external voltages to electronic components may result in component
or circuit board failure.
• Intermittent operation of electronic circuit boards is unlikely. board failure will normally be permanent. If an
intermittent condition is encountered, the cause will likely be a switch contact or a loose wire connection at
a terminal or crimp.
• Solenoid removal requires interrupting the water supply to the valve. Damage may result if solenoids are
energized for more than ten minutes without a supply of water.
• The use of two wrenches is recommended whenever plumbing fittings are tightened or loosened. This will
help avoid twists and kinks in the tubing.
• Make certain that all plumbing connections are sealed and all electrical connections are tight and isolated.
• This dispenser is heated at all times. Keep away from combustibles.
WARNING:
• Exercise extreme caution when servicing electrical equipment.
• Disconnect the brewer from the power source when servicing, except when electrical tests are specified. The
red “Power LED” on the door indicates that the unit is connected to AC Power.
• Follow recommended service procedures.
• Replace all protective shields or safety notices.
Front Panel LED Display Messages
Power LED “OFF”
No AC Power
Dispenser Not plugged in.
AC Circuit Breaker OFF
Check Power Cord
Check the AC Power Circuit Breaker
Service Required
Ready LED “OFF”
Water Temp. Too Low
Usage has exceeded the
capacity of the Tank Heater
Check Tank Temp Setting
Check Ready Temp. Setting
Service Required: Change the Supply Voltage,
see Optional Field Wiring
Rinse LED “ON”
Rinse Timer
Rinse Cycle Required
Rinse Dispenser, see Rinse Procedure
Rinse LED “FLASHING”
Rinse Lockout Enabled
Dispenser Locked Out
Rinse Cycle Required
Rinse Dispenser, see Rinse Procedure
Alternate Portion Dispenser
Volume #2 has been selected
Activate the Dispenser within 5 sec. to
dispense the pre-selected volume.
Portion LED “ON”
Portion Dispense
Enabled
25
34766 042304
Troubleshooting (Continued)
Left Refill LED “ON”
Left BIB Empty
Concentrate BIB is Empty.
BIB Not properly connected
Tubing kinked or blocked
Empty BIB warning set too high
Replace BIB, see Loading the Concentrate
Check BIB Connector Fittings
Check Tubing Installation
Check Threshold, see Field Calibrating the
Emoty BIB Warning
Right Refill LED “ON”
Right BIB Empty
Concentrate BIB is Empty.
BIB Not properly connected
Tubing kinked or blocked
Empty BIB Warning set too high
Replace BIB, see Loading the Concentrate
Check BIB Connector Fittings
Check Tubing Installation
Check Threshold, see Field Calibrating the
Empty BIB Warning
Left Refill LED
“FLASHING”
Empty BIB Lockout
Enabled
Left Dispenser will not operate
Replace BIB, see loading the Concentrate
Left Refill LED
“FLASHING”
Empty BIB Lockout
Enabled
Left Dispenser will not operate
Replace BIB, see loading the Concentrate
The Dispenser has detected an
Internal Fault
Remove the lower splash guard to view the
Fault message, See Diagnostics. After the
fault has been repaired or corrected - Hold
the “Stop” button for 10 seconds to clear
the message.
All LED’s “FLASHING”
Fault Detected
26
34766 102103
Troubleshooting (Continued)
Dispenser Diagnostics-LCD Display
Screen DisplayedPossible CauseTroubleshooting Procedures
LF TARGET RPM
TOO HIGH !!
1. The Tube Size selected for the Left Refer to “Selecting the Correct Pump
Hand Dispenser is too small for the Tubing” section of the manual.
application.
TUBE TOO SMALL
CHECK DISP RATIO
2. The Ratio selected for the Left Hand Refer to recommended Dispense Ratio
Dispenser is not correct for the on the product label.
application.
RT TARGET RPM
TOO HIGH !!
1. The Tube Size selected for the Right Refer to “Selecting the Correct Pump
Hand Dispenser is too small for the Tubing” section of the manual.
application.
TUBE TOO SMALL
CHECK DISP RATIO
2. The Ratio selected for the Right Refer to recommended Dispense Ratio
Hand Dispenser is not correct for the on the product label.
application.
LF TARGET RPM
TOO LOW !!
1. The Tube Size selected for the Left Refer to “Selecting the Correct Pump
Hand Dispenser is too large for the Tubing” section of the manual.
application.
TUBE TOO LARGE
CHECK DISP RATIO
2. The Ratio selected for the Left Hand Refer to recommended Dispense Ratio
Dispenser is not correct for the on the product label.
application.
RT TARGET RPM
TOO LOW !!
1. The Tube Size selected for the Right Refer to “Selecting the Correct Pump
Hand Dispenser is too large for the Tubing” section of the manual.
application.
TUBE TOO LARGE
CHECK DISP RATIO
2. The Ratio selected for the Right Refer to recommended Dispense Ratio
Hand Dispenser is not correct for the on the product label.
application.
LEFT BIB EMPTY!
1. Concentrate BIB is Empty.
Replace BIB, see loading the Concentrate
2. BIB Not properly connected.
Check BIB Connector Fittings
REPLACE PRODUCT
3. Tubing kinked or blocked.
Check Tubing installation
CHECK THRESHOLD
4. Empty BIB Warning set too high.
Check Threshold, see Field Calibrating
the Empty BIB Warning
RIGHT BIB EMPTY!
1. Concentrate BIB is Empty.
Replace BIB, see loading the Concentrate
2. BIB Not properly connected.
Check BIB Connector Fittings
REPLACE PRODUCT
3. Tubing kinked or blocked.
Check Tubing installation
CHECK THRESHOLD
4. Empty BIB Warning set too high.
Check Threshold, see Field Calibrating
the Empty BIB Warning
27
34766 011604
Troubleshooting (Continued)
Screen DisplayedPossible CauseTroubleshooting Procedures
OVERFLOW CUP
FULL. EMPTY CUP
HEATING TIME TOO
LONG
CHECK HEATING
CIRCUIT
FILL TIME TOO LONG
CHECK WATER SUPPLY
1. Refill valve stuck open
Service Required
2. Faulty refill probe
Service Required
3. Faulty overflow switch
Service Required
1. Tank Heater failure
Service Required
2. Triac failure
Service Required
3. Tank Temp. sensor failure
1. Water shut off to dispenser
Service Required
2. Inlet Solenoid Valve failure
Service Required
Check water supply shut-off
TANK TEMP SENSOR
OUT OF RANGE
CHECK FOR BAD
CONNECTIONS
1. Corresponding Temperature Sensor Service Required
Probe wire(s) broken or disconnected
COOL TEMP SENSOR
OUT OF RANGE
1. Corresponding Temperature Sensor Service Required
Probe wire(s) broken or disconnected.
CHECK FOR BAD
CONNECTIONS
2. Product cabinet temperature too low.
Service Required
EVAP TEMP SENSOR
OUT OF RANGE
1. Corresponding Temperature Sensor
Probe wire(s) broken or disconnected.
Service Required
CHECK FOR BAD
CONNECTIONS
2. Evaporator temperature too low.
Service Required
TANK TEMP SENSOR
OUT OF RANGE
CHECK WIRE FOR
SHORTS
1. Corresponding Temperature Sensor
Probe wire(s) shorted to housing, or to
each other.
Service Required
COOL TEMP SENSOR
OUT OF RANGE
1. Corresponding Temperature Sensor
Probe wire(s) shorted to housing, or
to each other.
Service Required
2. Product cabinet temperature too high.
Service Required
CHECK WIRE FOR
SHORTS
28
34766 011604
Troubleshooting (Continued)
Screen DisplayedPossible CauseTroubleshooting Procedures
EVAP TEMP SENSOR
OUT OF RANGE
CHECK WIRE FOR
SHORTS
1. Corresponding Temperature Sensor
Probe wire(s) shorted to housing, or
to each other.
Service Required
2. Evaporator temperature too high.
Service Required
LEFT PUMP FAULT!
CHK PUMP WIRING
CHK RPM SENSOR
CHK TUBING AREA
1.
Motor failure Service Required
RT PUMP FAULT!
CHK PUMP WIRING
1.
Motor failure Service Required
CHK RPM SENSOR
CHK TUBING AREA
COOLER FAULT!
EVAP TEMP TOO HI
CHECK EVAP FAN
CHK EVAP SENSOR
COOLING TIME
TOO LONG
CHECK AIR FILTER
CHECK COOLING UNIT
COND PROBE FAULT
CHECK COND PROBES
CHK DISP SWITCHES
CHK CONNECTIONS
JUMPER FAULT!
CONFIG NOT VALID
2. RPM Sensor failure
Service Required
2. RPM Sensor failure
Service Required
1. Cabinet circulating fan failure
Service Required
2. Ice build up on evaporator coils
Service Required
3. Evaporator sensor failure
Service Required
1. Air intake filter clogged
Clean Air Filter
2. Wiring failure
Check wiring harness for breaks,
shorts, open connectors
3. Compressor failure
Service Required
1. Concentrate buildup on probes
Check pump & tubing for proper
installation. Clean probes
Dispense switch failure, Service
Required
Dispense valve leaking, Service
Required
2. Machine dispensing continously
3. Water flowing continously
1. Invalid wire harness configuation
Service Required
CHECK J-18
ON CONTROL BOARD
29
34766 010407
Field Calibration of the Concentrate Pumps / Dispenser Flow Rates
The factory set Default Values for the Pump & Dispenser Flow Rates are very accurate and typically do not
need to be field calibrated. However, if the mix ratio accuracy is ever in question, this procedure can be used to
recalibrate the unit in the field.
Equipment Required:
50 to 100 ml graduated cylinder, with 1 ml graduations.
64 Oz (2000 ml) graduated container.
Remove the lower splash guard assembly to access prior to starting this procedure
NOTE: You can calibrate either the Concentrate Pump or the Dispenser Flow Rate independently. Simply scroll
through the menu screen to the desired section and perform only those steps.
Calibrating the Left Side Dispenser
Concentrate Pump Calibration
1. Select PRIME on the Function Selector Switch. (refer to Priming the Concentrate Lines).
2. Place a container under the Left Dispense Tip and prime the concentrate lines until a steady stream of
concentrate comes out the tip (approximately 10 seconds).
3. Stop the Priming and allow the tip to stop dripping. Discard the concentrate collected.
4. Select NORMAL on the Function Selector Switch.
5. Locate the programming module and use the Arrow Down key to scroll through LCD screens until CAL
LEFT SIDE appears and press the YES button.
6. The CAL LEFT PUMP menu screen will be displayed. Place a 50 ml graduated cylinder under Left Dispense
Tip and activate the Left Dispenser momentarily. The dispenser will run the Left Concentrate Pump for
20 seconds and then shut OFF automatically.
7. Keep the graduated cylinder under dispense tip until all the concentrate has dripped out.
8. Measure the volume of concentrate collected in the graduated cylinder.
Acceptable ranges for the volume collected
Tubing SizeVolume Collected
3/16” tubing
40 - 47 ml.
1/8” tubing 16 - 22 ml
9. If the amount collected is not within the acceptable range, empty the graduated cylinder and repeat STEPS
6 – 8.
10.If the amount collected is still not within range, replace the pump tubing with a new Tube Kit, (refer to
the Tube Replacement Instructions).
11.When satisfied with the volume of concentrate collected, press the Down Arrow Key
12.The CAL LF PUMP VOL menu screen will be displayed. Use the (-) / (+) keys to adjust number displayed
to the amount measured in STEP 8.
(Continued Next Page)
30
34766 073007
Field Calibration of the Concentrate Pumps / Dispenser Flow Rates
(Continued)
Dispenser Flow Rate Calibration
13.Press Down Arrow Key to display the CAL LF WTR FLO menu screen.
14.Place a 64 Oz (2000 ml) graduated container under Left Dispense Tip and Pull the Left Dispense Handle
momentarily. The dispenser will dispense water for 20 seconds and then shut OFF automatically.
15.Keep the graduated container under dispense tip until all the water stops dripping.
16.Measure the volume of water collected in the graduated container.
Acceptable ranges for the volume collected
_____Dispenser Flow Rate___________ ____Volume Collected____
1.8 Oz/sec (53 ml/sec) w/ flow restrictor 32 - 38 Oz, (946 - 1124 ml)
2.5 Oz/sec (74 ml/sec) w/o flow restrictor 46 - 52 Oz ,(1360 - 1538 ml)
17.If the amount collected is not within the acceptable range, empty the graduated container and repeat
STEPS 14 – 16
18.If the amount collected is still not within range, inspect the dispense valves, tubing and mix chamber for
lime, kinks or other obstructions.
19.When satisfied with the volume of concentrate collected, press the Down Arrow Key.
20.The CAL LF WTR VOL screen will be displayed. Use the (-) / (+) keys to adjust number displayed to the
amount measured in STEP 16.
21.Press Down Arrow Key again to exit the CAL LEFT SIDE functions.
Calibrating the Right Side Dispenser
Repeat STEPS 1-21 above for the “CAL RIGHT SIDE” menus.
Field Calibrating the Hot Water Flow Rate
1. Locate the programming module and use the Arrow Down key to scroll through the LCD screen until “CAL
HOT WTR FLO?” appears.
2. Place a 64 Oz (2000 ml) graduated container under Hot Water Tip and press the hot water switch. The unit
will dispense Hot Water for 20 seconds and then shut OFF automatically. Keep the graduated container under
the dispense tip until all the water stops dripping.
3. Measure the volume of water collected in the graduated container. The acceptable range for the volume
collected is 32 - 38 Oz. (946 - 1124 ml).
4. If the amount collected is not within the acceptable range, empty the container and repeat steps 2 & 3.
5. If the amount collected is still not within range, inspect the hot water valve, tubing and fittings for lime, kinks,
or other obstructions.
6. When satisfied with the volume of concentrate collected, press the Down Arrow Key.
7. The “CAL HOT WTR VOL” screen will be displayed. Use the (-) / (+) keys to adjust number displayed to the
ammount measured in step 3.
8. Press Down Arrow Key again to exit this function.
31
34766 120105
Field Calibrating the Empty BIB Warning
The dispenser will automatically turn on the Left or Right “REFILL LED”, see Operating Controls and Interface,
when the corresponding BIB is Empty. The Refill message is triggered when the FlavorGardTM sensor reading
drops below the minimum setting. The factory set minimum is 500 and should be correct for most locations.
However, in some areas the hardness of the local water supply may effect this reading. If the Refill message
doesn’t come on when the BIB is empty or the message comes on too early and there is still concentrate left in
the BIB, use the following procedure to find the correct Empty BIB threshold.
Calibrating The Empty BIB Threshold
1. Remove the lower splash guard assembly to access the digital programming module with LCD display.
2. Open the cabinet door and set the Function Switch to the “Rinse” position. Close the door.
3. Place a large container under the Left dispenser tip, then activate and hold the left dispenser.
4. Dispense long enough to rinse all the concentrate out of the mix chamber and for the Conductance reading
to stabilize and stop dropping.
5. Record the nominal Conductance value displayed. (NOTE: It is typical for this value fluctuate (+/- 25) points
about the nominal value}. This is the conductance reading of the water in your area.
6. Repeat steps 3, 4 & 5 for the Right dispenser.
7. Add 100 points to the larger of the Left or Right side Conductance value. This is the new Empty BIB threshold
value for your dispenser.
8. Enter this new value into the Empty BIB Alarm threshold, see Programming the Dispenser.
32
34766 120105
SCHEMATIC WIRING DIAGRAM
LCA-2/LCA-2, PC/LCA-2C/LCA-2C, PC/LCC-2/LCC-2C
(Older models may not have the Master Sw. and/or 10 Amp Fuses)
L1
RED-14
BLK-14
N (120V 2-Wire)
L2 (208-240V 2-Wire)
MASTER ON/OFF
SWITCH
BLK-14
Early Models
SW. & THERMOSTAT
TRIAC
BLK-14
BLU-14
BLU-14
TANK HEATER
LIMIT
THERMOSTAT
2
BLK-14 1
RED-14
RED-14
3
RED
BLK
TUBE
WARMER
10 AMP
BLK
RED
4
WHI
BLK
UNIVERSAL
POWER SUPPLY
-V
+V
N(L2)
L(L1)
-V
+V
PORTION
CONTROL
TAN
BLK
WHI
BLK
GRN
GRN
RED
Fuse 1
WHI
10 AMP
OVERFLOW
PROTECTION SW
RED
RED
WHI/GRY
RED
RED
1
2
3
4
5
6
7
BLK RIGHT
PUMP
RED
RED
J15-4
WHI
GRY
ORN
BLK
BLK
BLK
WHI
RED
GRN
J2 -8
J15-1
SOL
BLU/BLK
REFILL
J14-1
J3-6
J14-7
VIO
BLU
RED
YEL
ORN
BLK
BLK
RED
WHI/ORN
WHI/YEL
WHI/YEL
YEL
ORN
WHI/ORN
J7-1
J7-5
J7-10
J8-1
J8-3
GRN
J4-1
C
O
N
T
R
O
L
P
C
B
O
A
R
D
J18-1
J4-5
J5-1
RED
RED/BLK
BRN/WHI
BRN/BLK
WHI/GRY
BLU/BLK
J5-3
J16-1
J16-5
J16-12
GRN
BLK
BLU
ORN
WHI/ORN
WHI/YEL
PNK
VIO
BLK
BLK
BLK
BLK
GRN
BLK
BLK
ORN
RED
BLK
VIO
RED
1
WHI/YEL
J18-6
BLK
WHI/ORN
RT DISP. SW.
J1-16
J6-1
RED
BLK
RED
BLK
WHI/RED
BLK
RED
WHI/BLU
BLK
VIO
BLK
WHI
BLK
RED/WHI
BLU/BLK
RED
GRN/BLK
WHI/BLK
ORN
BLK
RIGHT
CONDUCTANCE
SENSOR
GRN
t
BLK
J6-5
J6-10
WHI
RED/BLK
RED/WHI
ORN/BLK
WHI/GRY
WHI/VIO
WHI/YEL
TAN
RED
BLU/WHI
RED/BLK
GRN
ORN/BLK
GRN/WHI
BLU/WHI
BLU/BLK
ORN
GRN/BLK
WHI/BLK
S J1-1
W
I
T
C
H J1-5
A
N
D
L
E J1-10
D
B
O
A
R
D
GRN
GRN/WHI
LF DISP. SW.
J6-20
DISPENSERS WITH
PORTION CONTROL
J6-15
LEFT
CONDUCTANCE
SENSOR
P
R
O
B
E
WHI
RED
BLK
GRN
J3-1
BRN/WHI
SOL
LEFT DISP
BLK
RIGHT RPM
SENSOR
RED
WHI/BLU
RED
WHI/RED
HEAT SINK
THERMISTOR
RED
BLK
BLU
RED
BLK
BLU
LEFT
PUMP
BRN/BLK
SOL
WHI
WHI
RED
BLK
GRN
J2-1
TAN
BLK
LEFT RPM
SENSOR
BLK
J1-4
NO (-)
RED/BLK
RIGHT DISP
J1-1
EXIT
SOL
HOT WATER
TOUCHPAD
YES (+)
WHI/GRY
DOOR
BLK
t
PELTIER
RED
BLK
TUBE
WARMER
Fuse 1
GRN
WHI
SELECTOR
SWITCH
NITE
BLK
120 VOLTS AC 2 WIRE
120/208-240 VOLTS AC 3 WIRE
208-240 VOLTS AC 2 WIRE
SINGLE PHASE 50/60HZ
SELECTOR
SWITCH
WHI/GRY
RINSE
COOLING CABINET
WHI/YEL
BLK
RUN
WHI/VIO
PRIME
t
CABINET
THERMISTOR
TAN
BLK
LLC Models only
34641.0004A 07/10 © 2010 BUNN-O-MATIC CORPORATION
33
34766 062210
L1
SCHEMATIC WIRING DIAGRAM LCC-2A/LCA-2A/LCA-2A, PC
CAPACITOR .01uF
GRN
CAPACITOR .01uF
GRN
GRN
RFI SUPPRESION
CAPACITOR 2.2uF
BLK
BLK
BLK-14
DOUBLE POLE
LIMIT THERMOSTAT
1
2
Early Models
SW. & THERMOSTAT
TRIAC
BLK-14
BLU-14
BLU-14
TANK HEATER
RED-14
RED-14
3
Fuse 1
BLK
WHI
RED
BLK
TUBE
WARMER
BLK
RED
N(L2)
L(L1)
-V
+V
-V
+V
WHI
BLK
GRN
GRN
RED
Fuse 2
WHI
10 AMP
PORTION
CONTROL
TAN
UNIVERSAL
POWER SUPPLY
OVERFLOW
PROTECTION SW
RED
RED
WHI/GRY
RED
RED
1
2
3
4
5
6
7
J7-10
GRN
GRN
J16-12
1
P
R
O
B
E
BLK
WHI
BLK
RED/WHI
BLU/BLK
RED
GRN/BLK
WHI/BLK
ORN
WHI/ORN
LEFT
CONDUCTANCE
SENSOR
BLK
GRN
t°
RIGHT
CONDUCTANCE
SENSOR
HEAT SINK
THERMISTOR
RED
BLK
BLU
BLK
VIO
BLU/WHI
RED/BLK
GRN
ORN/BLK
GRN/WHI
BLK
WHI/RED
BLK
J6-10
WHI
RED/BLK
RED/WHI
ORN/BLK
WHI/GRY
WHI/VIO
WHI/YEL
TAN
RED
BLU/WHI
BLU/BLK
ORN
GRN/BLK
WHI/BLK
J6-20
GRN
GRN/WHI
J6-15
WHI/YEL
BLK
t°
PELTIER
RED
WHI
SELECTOR
SWITCH
NITE
SELECTOR
SWITCH
WHI/GRY
BLK
230 VOLTS AC
2 WIRE
SINGLE PHASE
50 HZ
J16-5
B
O
A
R
D
BLU
ORN
WHI/ORN
WHI/YEL
PNK
VIO
BLK
BLK
BLK
BLK
GRN
BLK
J18-6
DISPENSERS WITH
PORTION CONTROL
B
O
A
R
D J1-16
J15-4
C
J18-1
BLU/BLK
J5-3
J16-1
P
J8-3
L
E J1-10
D
J5-1
BLK
ORN
J7-5
J4-5
RED
RED/BLK
BRN/WHI
BRN/BLK
WHI/GRY
WHI
J7-1
J4-1
BLK
BLK
VIO
BLU
RED
YEL
ORN
BLK
BLK
RED
WHI/ORN
WHI/YEL
ORN
WHI/ORN
RT DISP. SW.
GRY
ORN
BLK
BLK
C
O
N
T
R
O
L
J14-7
WHI/YEL
YEL
S
W J1-1
I
T
C
H
J1-5
A
N
D
J15-1
J2 -8
J3-6
J8-1
LF DISP. SW.
WHI
BLK
RED
GRN
J2-1
WHI
J14-1
RED
BLK
RED
BLU/BLK
WHI
WHI
BLK RIGHT
PUMP
SOL
RED
WHI/BLU
RED
BLK
VIO
RED
RED
BLK
RED
BLK
GRN
BRN/WHI
SOL
LEFT DISP
WHI/BLU
RED
WHI/RED
J6-1
RIGHT RPM
SENSOR
RED
J3-1
BLK
RED
BLK
BLU
RED
BRN/BLK
SOL
REFILL
J6-5
RED
BLK
GRN
LEFT
PUMP
J1-4
TAN
BLK
LEFT RPM
SENSOR
BLK
RED/BLK
RIGHT DISP
J1-1
EXIT
NO (-)
SOL
HOT WATER
TOUCHPAD
YES (+)
WHI/GRY
DOOR
BLK
TUBE
WARMER
4
BLK
10 AMP
N
RINSE
WHI/YEL
COOLING CABINET
BLK
RUN
WHI/VIO
PRIME
TAN
t°
CABINET
THERMISTOR
BLK
34641.0001K 06/11 © 2002 BUNN-O-MATIC CORPORATION
LCC Models only
34
34766 060611
Download PDF

advertising