Technical information | Bush MPK4230BUK MP3 Player User Manual

Hardware Maintenance Manual
IBM NetVista Computer Types 6058,
6059, 6269, 6568, 6569,
6578, 6579, 6648, 6649
Hardware Maintenance Manual
IBM NetVista Computer Types 6058,
6059, 6269, 6568, 6569,
6578, 6579, 6648, 6649
Note:
Before using this information and the product it supports, be sure to read the general information
under “Notices” on page 228.
Second Edition (November 2000)
The following paragraph does not apply to the United Kingdom or any country where such provisions are
inconsistent with local law:
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION ″AS IS″ WITHOUT
ANY WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
LIMITED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not
allow disclaimers or express or implied warranties in certain transactions; therefore, this statement may not apply to
you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the
information herein; these changes will be incorporated in new editions of the publication. IBM may make
improvements or changes in the products or the programs described in this publication at any time.
Requests for technical information about IBM products should be made to your IBM Authorized Dealer or your IBM
Marketing Representative.
© Copyright International Business Machines Corporation 2000. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
About this manual
®
This manual contains service and reference information for the IBM
NetVistaTM Series computer types 6058, 6059, 6269, 6568, 6569, 6578, 6579,
6648, 6649.
This manual is divided into product service sections (by machine chassis) and
a related service section, as follows:
v The product service sections include procedures for isolating problems to a
FRU, a Symptom-to-FRU Index, additional service information and an
illustrated parts catalog.
v The related service section includes safety notices and safety information,
and problem determination tips.
Note: This manual is intended for trained servicers who are familiar with
IBM Personal Computer products. Use this manual along with
advanced diagnostic tests to troubleshoot problems effectively.
Before servicing an IBM product, be sure to review the “Safety notices
(multi-lingual translations)” on page 189 and “Safety information” on
page 185.
© Copyright IBM Corp. 2000
iii
Important Safety Information
Be sure to read all caution and danger statements in this book before
performing any of the instructions.
Prenez connaissance de toutes les consignes de type Attention et Danger
avant de procéder aux opérations décrites par les instructions.
Lesen Sie alle Sicherheitshinweise, bevor Sie eine Anweisung ausführen.
Accertarsi di leggere tutti gli avvisi di attenzione e di pericolo prima di
effettuare qualsiasi operazione.
Leia todas as instruções de cuidado e perigo antes de executar qualquer
operação.
Lea atentamente todas las declaraciones de precaución y peligro ante de llevar
a cabo cualquier operación.
iv
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
About this manual
v
vi
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Related Publications
The following publications are available for IBM products. For more
information, contact IBM or an IBM Authorized Dealer.
For Information About:
®
See Publication:
®
PC300/700 and IntelliStation computers Volume 1 Hardware Maintenance Manual
®
IBM Personal Computer HMM Volume 1
(S83G-7789)
PC300 and IntelliStation computers (Including
®
Aptiva 2173) - Volume 2 Hardware Maintenance
Manual
IBM Personal Computer HMM Volume 2
(S00N-4019)
PC300 and IntelliStation computers - Volume 3
Hardware Maintenance Manual
IBM Personal Computer HMM Volume 3
(S09N-8603)
®
PS/2 Computers
IBM Personal System/2 HMM (S52G-9971)
®
PS/ValuePoint Computers
IBM PS/ValuePoint Hardware Maintenance
Service and Reference (S61G-1423)
®
IBM Mobile Systems HMM Volume 1 (S82G-1501)
Laptop, Notebook, Portable, and ThinkPad
Computers (L40, CL57, N45, N51, P70/P75,
ThinkPad 300, 350, 500, 510, 710T, Expansion Unit,
Dock I, Dock II)
ThinkPad Computers (340, 355, 360, 370, 700, 701,
720, 750, 755)
IBM Mobile Systems HMM Volume 2 (S82G-1502)
ThinkPad Computers (365, 560, 760, SelectaDock)
IBM Mobile Systems HMM Volume 3 (S82G-1503)
Monitors (Displays) (February 1993)
IBM PS/2 Display HMM Volume 1 (SA38-0053)
Monitors (December 1993)
IBM Color Monitor HMM Volume 2 (S71G-4197)
IBM Monitors (P/G Series) (June 1996)
IBM Monitor HMM Volume 3 (S52H-3679)
IBM 2248 Monitor (February 1996)
IBM Monitor HMM Volume 4 (S52H-3739)
Disk Array technology overview and using the
IBM RAID Configuration Program
Configuring Your Disk Array booklet (S82G-1506)
Installation Planning for Personal System/2
computers
Personal System/2 Installation Planning and
Beyond (G41G-2927)
Installation Planning for Advanced Personal
System/2 Servers
Advanced PS/2 Servers Planning and Selection
Guide (GG24-3927)
© Copyright IBM Corp. 2000
vii
viii
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Contents
About this manual . . . .
Important Safety Information .
.
.
.
.
.
.
.
.
. iii
. iv
Related Publications
.
.
.
.
. vii
.
.
.
Chapter 1. IBM PC Enhanced Diagnostics
error codes . . . . . . . . . . .
Chapter 2. Types 6568/6569/6648/6649 . .
Product description . . . . . . . . .
Specifications Information (ISO/ANSI) . .
Specifications - Types
6568/6569/6648/6649 . . . . . . . .
General checkout . . . . . . . . . .
Module test menu and hardware
configuration report . . . . . . . .
Keyboard . . . . . . . . . . . .
Printer . . . . . . . . . . . . .
Power supply . . . . . . . . . .
20-pin main power supply connection . .
Display . . . . . . . . . . . .
Diagnostics, test and recovery information . .
Power-On Self-Test (POST) . . . . . .
POST beep codes . . . . . . . . .
Error code format . . . . . . . . .
Product Recovery Program menu . . . .
IBM PC Enhanced Diagnostics . . . . .
Enhanced Diagnostics download or
diskette . . . . . . . . . . .
Navigating through the diagnostics
programs . . . . . . . . . . .
Running diagnostics tests . . . . .
Test selection. . . . . . . . . .
IBM PC Enhanced Memory Diagnostics
Alert-On LAN™ test . . . . . . .
Asset ID™ test . . . . . . . . .
Test results . . . . . . . . . .
Hard file Smart test . . . . . . .
IBM Fixed Disk Optimized Test . . .
Quick and Full erase - hard drive . . .
Iomega Zip drive test . . . . . . .
Asset EEPROM backup . . . . . .
Viewing the test log . . . . . . .
SIMM/DIMM/RIMM memory errors
Setup Utility program . . . . . . . .
© Copyright IBM Corp. 2000
. 1
21
23
24
24
26
28
29
29
30
31
32
33
33
33
34
34
35
35
36
36
36
36
37
37
37
38
38
39
40
40
40
40
41
Hard disk drive boot error . . . . . .
When to use the Low-Level Format
program . . . . . . . . . . . .
Preparing the hard disk drive for use . .
Additional service information . . . . . .
Replacing a processor . . . . . . . .
Replacing a system board . . . . . .
Security features . . . . . . . . .
Passwords . . . . . . . . . .
Vital product data . . . . . . . .
Management Information Format (MIF)
Alert on LAN . . . . . . . . .
Hard disk drive jumper settings . . . .
CD-ROM drive jumper settings . . . .
BIOS levels . . . . . . . . . . .
Flash (BIOS/VPD) update procedure. . .
Flash recovery boot block jumper . . . .
Power management . . . . . . . .
Automatic configuration and power
interface (ACPI) BIOS . . . . . . .
Advanced Power Management . . . .
Automatic Hardware Power
Management features . . . . . . .
Setting Automatic Hardware Power
Management features . . . . . . .
Automatic Power-On features . . . .
Network settings . . . . . . . . .
Flash over LAN (update POST/BIOS
over network) . . . . . . . . .
Wake on LAN . . . . . . . . .
System board memory . . . . . . .
Supported memory configuration . . .
Computer exploded view Types 6568/6569/6648/6649 . . . . . .
Input/Output connectors . . . . . .
Cover removal . . . . . . . . . .
Replacing the cover . . . . . . . .
EMC shield (CD-ROM drive bay) . . . .
EMC shield (system board) . . . . . .
Installing adapters . . . . . . . . .
Adapter slots . . . . . . . . .
CD-ROM drive removal and replacement
Internal drive removal . . . . . . .
3.5″ drive removal . . . . . . . .
Hard drive removal . . . . . . .
42
42
43
44
45
45
46
46
47
47
48
48
49
49
50
50
51
51
51
52
52
53
53
54
54
55
55
55
56
57
57
58
58
59
59
60
63
63
64
ix
Fan/speaker bracket removal . . . .
Power supply removal . . . . . .
Components of the riser card . . . .
A40 and A40P system board layout . . .
System board locations . . . . . .
A40/A40P System board jumper settings
A40/A40P Clear CMOS/Flash Boot
Block Recovery . . . . . . . .
A40/ A40P Processor Speed Settings .
A40/A40P Diskette Write Access . .
Symptom-to-FRU index . . . . . . .
Beep symptoms . . . . . . . . .
No-beep symptoms . . . . . . .
POST error codes . . . . . . . .
Miscellaneous error messages . . . .
Undetermined problems . . . . . . .
Model tables - Country/Region/Language .
Parts - Types 6568/6569/6648/6649 . . .
Parts listing . . . . . . . . . .
Keyboards - 6568/6569
(PCNext Lite Pearl White) . . . .
Keyboards - 6648/6649
(PCNext Lite Black) . . . . . .
Computer Power Cords . . . . .
Display and Monitor Information . .
Special tools . . . . . . . . . .
Chapter 3. Types 6058/6059/6269/6578/6579
Product description . . . . . . . . .
Specifications Information (ISO/ANSI)
Specifications Types 6058/60596269/6578/6579 . . . .
General checkout . . . . . . . . . .
Module test menu and hardware
configuration report . . . . . . . .
Keyboard . . . . . . . . . . .
Printer . . . . . . . . . . . .
Power supply . . . . . . . . . .
20-pin main power supply connection
Display . . . . . . . . . . . .
Diagnostics, test and recovery information
Power-On Self-Test (POST) . . . . . .
POST beep codes . . . . . . . . .
Error code format . . . . . . . . .
Product Recovery Program menu . . .
IBM PC Enhanced Diagnostics . . . .
Enhanced Diagnostics download or
diskette . . . . . . . . . . .
Navigating through the diagnostics
programs . . . . . . . . . .
x
6649
.
.
.
.
.
64
65
65
67
67
67
.
.
.
.
.
.
.
.
.
.
.
.
67
68
68
69
70
72
72
87
90
91
92
93
. 95
.
.
.
.
96
98
98
98
99
101
102
102
104
106
107
107
108
109
110
111
111
112
112
112
113
113
114
Running diagnostics tests . . . .
Test selection . . . . . . . .
IBM PC Enhanced Memory
Diagnostics . . . . . . . . .
Alert-On LAN test . . . . . .
Asset ID test . . . . . . . .
Test results . . . . . . . . .
Hard file Smart test . . . . . .
IBM Fixed Disk Optimized Test . .
Quick and Full erase - hard drive .
Iomega Zip drive test . . . . .
Asset EEPROM backup . . . . .
Viewing the test log . . . . . .
SIMM/DIMM/RIMM memory errors
Setup Utility program . . . . . .
Hard disk drive boot error . . . . .
When to use the Low-Level Format
program . . . . . . . . . . .
Preparing the hard disk drive for use .
Additional service information . . . .
Replacing a processor . . . . . .
Replacing a system board . . . . .
Security features . . . . . . . .
Passwords . . . . . . . . .
Vital product data. . . . . . .
Management Information Format
(MIF) . . . . . . . . . . .
Alert on LAN . . . . . . . .
Hard disk drive jumper settings . . .
CD-ROM drive jumper settings . . .
BIOS levels . . . . . . . . . .
Flash (BIOS/VPD) update procedure .
Flash recovery boot block jumper . .
Power management . . . . . . .
Automatic configuration and power
interface (ACPI) BIOS . . . . .
Advanced Power Management . .
Automatic Hardware Power
Management features . . . . .
Setting Automatic Hardware Power
Management features . . . . .
Automatic Power-On features . . .
Network settings . . . . . . . .
Flash over LAN (update POST/BIOS
over network) . . . . . . . .
Wake on LAN . . . . . . . .
System board memory . . . . . .
Supported memory configuration .
Computer exploded view Types 6058/6059/6269/6578/6579 . . .
. 114
. 114
.
.
.
.
.
.
.
.
.
.
115
115
115
115
117
117
119
119
120
120
121
. 122
. 123
.
.
.
.
.
.
.
.
123
123
124
125
125
125
126
127
.
.
.
.
.
.
.
.
127
128
128
129
129
130
131
131
. 131
. 131
. 132
. 132
. 133
. 133
.
.
.
.
134
135
135
135
. 136
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Input/Output connectors - Type 6269 .
Input/Output connectors - Types
6058/6059/6578/6579 . . . . . .
Cover removal . . . . . . . . .
Replacing the cover . . . . . .
EMC shield (front) . . . . . . .
EMC shield (system board) . . . .
Installing adapters . . . . . . .
Adapter slots . . . . . . . .
Air duct (Types 6058/6059/6278/6279)
CD-ROM drive removal. . . . . .
Fan/speaker bracket removal . . . .
Hard drive removal . . . . . . .
Power supply removal . . . . . .
A20 system board layout (Type 6269) . .
System board locations . . . . . .
A20 System board jumper settings . .
A20 Clear CMOS/Flash Boot Block
Recovery. . . . . . . . . .
A20 Processor Speed Settings . . .
A20 Diskette Write Access . . . .
A40/A40P system board layout
(Types 6058/6059/6578/6579) . . . . .
System board locations . . . . . .
A40/A40P System board jumper settings
A40/A40P Clear CMOS/Flash Boot
Block Recovery . . . . . . .
A40/A40P Processor Speed Settings
A40/A40P Diskette Write Access. .
Symptom-to-FRU index . . . . . . .
. 137
.
.
.
.
.
.
.
.
.
.
.
.
.
.
138
139
139
140
140
140
140
141
142
142
143
144
146
146
146
. 146
. 147
. 147
. 148
. 148
148
. 149
149
. 149
. 150
Beep symptoms . . . . . . . .
No-beep symptoms . . . . . . .
POST error codes . . . . . . . .
Miscellaneous error messages . . . .
Undetermined problems . . . . . .
Model tables - Country/Region/Language
Parts - Types 6058/6059/6269/6578/6579
Parts listing . . . . . . . . . .
Keyboards - PCNext Lite Pearl White
Computer Power Cords . . . . .
Recovery CDs . . . . . . . .
Display and Monitor Information .
Special tools . . . . . . . .
.
.
.
.
.
.
.
.
.
.
Chapter 4. Related Service Information
Safety information . . . . . . . . .
General safety . . . . . . . . . .
Electrical safety . . . . . . . . .
Safety inspection guide . . . . . . .
Handling electrostatic discharge-sensitive
devices . . . . . . . . . . . .
Grounding requirements . . . . . .
Safety notices (multi-lingual translations)
Send us your comments! . . . . . . .
Problem determination tips . . . . . .
Notices . . . . . . . . . . . . .
Trademarks . . . . . . . . . . . .
Miscellaneous Information . . . . . . .
Acronyms, Abbreviations, and Terms . .
Contents
150
152
153
167
171
172
173
174
180
181
182
182
183
185
185
185
186
188
189
189
189
227
227
228
229
229
229
xi
xii
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Chapter 1. IBM PC Enhanced Diagnostics error codes
Refer to the following Diagnostic Error Codes when using the IBM PC
Enhanced Diagnostics test. See the ″Diagnostic and test information″ section
for the specific model for information about the IBM PC Enhanced
Diagnostics program.
In the following index, X can represent any number.
Diagnostic Error Code
FRU/Action
000-000-XXX BIOS Test Passed
1. No action
000-002-XXXBIOS Timeout
1. Flash the system
2. System board
000-024-XXXBIOS Addressing test failure
1. Flash the system
2. System board
000-025-XXXBIOS Checksum Value error
1. Flash the system
2. Boot block
3. System board
000-026-XXXFLASH data error
1. Flash the system
2. Boot block
3. System board
000-027-XXXBIOS Configuration/Setup error
1. Run Setup
2. Flash the system
3. Boot block
4. System board
000-034-XXXBIOS Buffer Allocation failure
1. Reboot the system
2. Flash the system
3. Run memory test
4. System board
000-035-XXXBIOS Reset Condition detected
1. Flash the system
2. System board
000-036-XXXBIOS Register error
1. Flash the system
2. Boot block
3. System board
© Copyright IBM Corp. 2000
1
Diagnostic Error Code
FRU/Action
000-038-XXXBIOS Extension failure
1. Flash the system
2. Adapter card
3. System board
000-039-XXXBIOS DMI data error
1. Flash the system
2. System board
000-195-XXXBIOS Test aborted by user
1. Information
2. Re-start the test, if necessary
000-196-XXXBIOS test halt, error threshold
exceeded
1. Press F3 to review the log file
000-197-XXXBIOS test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-start the test to reset the log file
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
000-198-XXXBIOS test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
000-199-XXXBIOS test failed, cause unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
000-250-XXXBIOS APM failure
1. Flash the system
2. System board
000-270-XXXBIOS ACPI failure
1. Flash the system
2. System board
001-000-XXXSystem Test Passed
1. No action
001-00X-XXXSystem Error
1. System board
001-01X-XXXSystem Error
1. System board
001-024-XXXSystem Addressing test failure
1. System board
001-025-XXXSystem Checksum Value error
1. Flash the system
2. System board
001-026-XXXSystem FLASH data error
1. Flash the system
2. System board
2
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Diagnostic Error Code
FRU/Action
001-027-XXXSystem Configuration/Setup error 1. Run Setup
2. Flash the system
3. System board
001-032-XXXSystem Device Controller failure
1. System board
001-034-XXXSystem Device Buffer Allocation
failure
1. Reboot the system
2. Flash the system
3. Run memory test
4. System board
001-035-XXXSystem Device Reset condition
detected
1. System board
001-036-XXXSystem Register error
1. System board
001-038-XXXSystem Extension failure
1. Adapter card
2. System board
001-039-XXXSystem DMI data structure error
1. Flash the system
2. System board
001-040-XXXSystem IRQ failure
1. Power-off/on system and re-test
2. System board
001-041-XXXSystem DMA failure
1. Power-off/on system and re-test
2. System board
001-195-XXXSystem Test aborted by user
1. Information
2. Re-start the test, if necessary
001-196-XXXSystem test halt, error threshold
exceeded
1. Press F3 to review the log file
001-197-XXXSystem test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-start the test to reset the log file
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
001-198-XXXSystem test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
Chapter 1. IBM PC Enhanced Diagnostics error codes
3
Diagnostic Error Code
FRU/Action
001-199-XXXSystem test failed, cause unknown 1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
001-250-XXXSystem ECC error
1. System board
001-254-XXX
001-255-XXX
001-256-XXX
001-257-XXXSystem DMA error
1. System board
001-260-XXX
001-264-XXXSystem IRQ error
1. System board
001-268-XXXSystem IRQ1 failure
1. Device on IRQ1
2. System board
001-269-XXXSystem IRQ2 failure
1. Device on IRQ2
2. System board
001-270-XXXSystem IRQ3 failure
1. Device on IRQ3
2. System board
001-271-XXXSystem IRQ4 failure
1. Device on IRQ4
2. System board
001-272-XXXSystem IRQ5 failure
1. Device on IRQ5
2. System board
001-273-XXXSystem IRQ6(diskette drive)
failure
1. Diskette Cable
2. Diskette drive
3. System board
001-274-XXXSystem IRQ7 failure
1. Device on IRQ7
2. System board
001-275-XXXSystem IRQ8 failure
1. Device on IRQ8
2. System board
001-276-XXXSystem IRQ9 failure
1. Device on IRQ9
2. System board
001-277-XXXSystem IRQ10 failure
1. Device on IRQ10
2. System board
001-278-XXXSystem IRQ11 failure
1. Device on IRQ11
2. System board
4
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Diagnostic Error Code
FRU/Action
001-279-XXXSystem IRQ12 failure
1. Device on IRQ12
2. System board
001-280-XXXSystem IRQ13 failure
1. Device on IRQ13
2. System board
001-281-XXXSystem IRQ14(hard disk drive)
failure
1. Hard disk drive cable
2. Hard disk drive
3. System board
001-282-XXXSystem IRQ15 failure
1. Device on IRQ15
2. System board
001-286-XXX
001-287-XXX
001-288-XXXSystem Timer failure
1. System board
001-292-XXXSystem CMOS RAM error
1. Run Setup and re-test
2. System board
001-293-XXXSystem CMOS Battery
1. Battery
2. System board
001-298-XXXSystem RTC date/time update
failure
1. Flash the system
001-299-XXXSystem RTC periodic interrupt
failure
1. System board
001-300-XXXSystem RTC Alarm failure
1. System board
001-301-XXXSystem RTC Century byte error
1. Flash the system
2. System board
2. System board
005-000-XXXVideo Test Passed
1. No action
005-00X-XXXVideo error
1. Video card, if installed
2. System board
005-010-XXX
005-011-XXX
005-012-XXX
005-013-XXXVideo Signal failure
1. Video card, if installed
005-016-XXXVideo Simple Pattern test failure
1. Video Ram
2. System board
2. Video card, if installed
3. System board
Chapter 1. IBM PC Enhanced Diagnostics error codes
5
Diagnostic Error Code
FRU/Action
005-024-XXXVideo Addressing test failure
1. Video card, if installed
2. System board
005-025-XXXVideo Checksum Value error
1. Video card, if installed
2. System board
005-027-XXXVideo Configuration/Setup error
1. Run Setup
2. Video drivers update
3. Video card, if installed
4. System board
005-031-XXXVideo Device Cable failure
1. Video cable
2. Monitor
3. Video card, if installed
4. System board
005-032-XXXVideo Device Controller failure
1. Video card, if installed
2. System board
005-036-XXXVideo Register error
1. Video card, if installed
2. System board
005-038-XXXSystem BIOS extension failure
1. Video card, if installed
2. System board
005-040-XXXVideo IRQ failure
1. Video card, if installed
2. System board
005-195-XXXVideo Test aborted by user
1. Information
2. Re-start the test, if necessary
005-196-XXXVideo test halt, error threshold
exceeded
1. Press F3 to review the log file
005-197-XXXVideo test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-start the test to reset the log file
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
005-198-XXXVideo test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
6
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Diagnostic Error Code
FRU/Action
005-199-XXXVideo test failed, cause unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
005-2XX-XXX
005-3XX-XXXVideo subsystem error
1. Video card, if installed
006-000-XXXDiskette interface Test Passed
1. No action
006-0XX-XXXDiskette interface error
1. Diskette drive Cable
2. System board
2. Diskette drive
3. System board
006-195-XXXDiskette interface Test aborted by
user
1. Information
006-196-XXXDiskette interface test halt, error
threshold exceeded
1. Press F3 to review the log file
006-197-XXXDiskette interface test warning
1. If a component is called out, make sure it is
connected and/or enabled
2. Re-start the test, if necessary
2. Re-start the test to reset the log file
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
006-198-XXXDiskette interface test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
006-199-XXXDiskette interface test failed, cause 1. Go to the ″Undetermined problems″ section
unknown
2. Flash the system and re-test
3. Replace component under function test
006-25X-XXXDiskette interface Error
1. Diskette drive cable
2. Diskette drive
3. System board
011-000-XXXSerial port Interface Test Passed
1. No action
011-001-XXXSerial port Presence
1. Remove external serial device, if present
2. Run setup, enable port
3. System board
011-002-XXX
011-003-XXXSerial port Timeout/Parity error
1. System board
Chapter 1. IBM PC Enhanced Diagnostics error codes
7
Diagnostic Error Code
FRU/Action
011-013-XXX
011-014-XXXSerial port Control
Signal/Loopback test failure
1. System board
011-015-XXXSerial port External Loopback
failure
1. Wrap plug
011-027-XXXSerial port Configuration/Setup
error
1. Run Setup, enable port
2. System board
2. Flash the system
3. System board
011-03X-XXX
011-04X-XXXSerial port failure
1. System board
011-195-XXXSerial port Test aborted by user
1. Information
2. Re-start the test, if necessary
011-196-XXXSerial port test halt, error
threshold exceeded
1. Press F3 to review the log file
011-197-XXXSerial port test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-start the test to reset the log file
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
011-198-XXXSerial port test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
011-199-XXXSerial port test failed, cause
unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
011-2XX-XXXSerial port signal failure
1. External serial device
2. System board
014-000-XXXParallel port Interface Test Passed
1. No action
014-001-XXXParallel port Presence
1. Remove external parallel device, if present
2. Run setup, enable port
3. System board
014-002-XXX
1. System board
014-003-XXXParallel port Timeout/Parity error
8
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Diagnostic Error Code
FRU/Action
014-013-XXX
014-014-XXXParallel port Control
Signal/Loopback test failure
1. System board
014-015-XXXParallel port External Loopback
failure
1. Wrap plug
014-027-XXXParallel port Configuration/Setup
error
1. Run Setup, enable port
2. System board
2. Flash the system
3. System board
014-03X-XXX
014-04X-XXXParallel port failure
1. System board
014-195-XXXParallel port Test aborted by user
1. Information
2. Re-start the test, if necessary
014-196-XXXParallel port test halt, error
threshold exceeded
1. Press F3 to review the log file
014-197-XXXParallel port test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-start the test to reset the log file
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
014-198-XXXParallel port test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
014-199-XXXParallel port test failed, cause
unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
014-2XX-XXX
014-3XX-XXXParallel port failure
1. External parallel device
015-000-XXXUSB port Interface Test Passed
1. No action
015-001-XXXUSB port Presence
1. Remove USB device(s) and re-test
2. System board
2. System board
015-002-XXXUSB port Timeout
1. Remove USB device(s) and re-test
2. System board
Chapter 1. IBM PC Enhanced Diagnostics error codes
9
Diagnostic Error Code
FRU/Action
015-015-XXXUSB port External Loopback
failure
1. Remove USB device(s) and re-test
015-027-XXXUSB port Configuration/Setup
error
1. Flash the system
2. System board
2. System board
015-032-XXXUSB port Device Controller failure 1. System board
015-034-XXXUSB port bufferallocation failure
1. Reboot the system
2. Flash the system
3. Run memory test
4. System board
015-035-XXXUSB port Reset condition detected 1. Remove USB device(s) and re-test
2. System board
015-036-XXXUSB port Register error
1. System board
015-040-XXXUSB port IRQ failure
1. Run setup and check for conflicts
2. Flash the system
3. System board
015-195-XXXUSB port Test aborted by user
1. Information
2. Re-start the test, if necessary
015-196-XXXUSB port test halt, error threshold 1. Press F3 to review the log file
exceeded
2. Re-start the test to reset the log file
015-197-XXXUSB port test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
015-198-XXXUSB port test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
015-199-XXXUSB port test failed, cause
unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
018-000-XXXPCI Card Test Passed
10
6649
1. No action
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Diagnostic Error Code
FRU/Action
018-0XX-XXXPCI Card Failure
1. Riser card, if installed
2. System board
018-195-XXXPCI Card Test aborted by user
1. PCI card
2. Information
3. Re-start the test, if necessary
018-196-XXXPCI Card test halt, error threshold 1. Press F3 to review the log file
exceeded
2. Re-start the test to reset the log file
018-197-XXXPCI Card test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
018-198-XXXPCI Card test aborted
1. Make sure the component that is called out is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
018-199-XXXPCI Card test failed, cause
unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
018-250-XXXPCI Card Services error
1. PCI card
2. Riser card, if installed
3. System board
020-000-XXXPCI Interface Test Passed
1. No action
020-0XX-XXXPCI Interface error
1. PCI card
2. Riser card, if installed
3. System board
020-195-XXXPCI Test aborted by user
1. Information
2. Re-start the test, if necessary
020-196-XXXPCI test halt, error threshold
exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
Chapter 1. IBM PC Enhanced Diagnostics error codes
11
Diagnostic Error Code
FRU/Action
020-197-XXXPCI test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
020-198-XXXPCI test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
020-199-XXXPCI test failed, cause unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
020-262-XXX
PCI system error
1. PCI card
2. Riser card, if installed
3. System board
025-000-XXX
IDE interface Test Passed
1. No action
025-00X-XXX
025-01X-XXXIDE interface failure
1. IDE signal cable
2. Check power supply
3. IDE device
4. System board
025-027-XXXIDE interface Configuration/Setup 1. IDE signal cable
error
2. Flash the system
3. IDE device
4. System board
025-02X-XXX
025-03X-XXX
025-04X-XXXIDE Interface failure
1. IDE signal cable
2. Check power supply
3. IDE device
4. System board
025-195-XXXIDE interface Test aborted by user 1. Information
2. Re-start the test, if necessary
025-196-XXXIDE interface test halt, error
threshold exceeded
12
6649
1. Press F3 to review the log file
2. Re-start the test to reset the log file
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Diagnostic Error Code
FRU/Action
025-197-XXXIDE interface test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
025-198-XXXIDE interface test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
025-199-XXXIDE interface test failed, cause
unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
030-000-XXXSCSI interface Test Passed
1. No action
030-00X-XXX
030-01X-XXXSCSI interface failure
1. SCSI signal cable
2. Check power supply
3. SCSI device
4. SCSI adapter card, if installed
5. System board
030-027-XXXSCSI interface
Configuration/Setup error
1. SCSI signal cable
2. Flash the system
3. SCSI device
4. SCSI adapter card, if installed
5. System board
030-03X-XXX
030-04X-XXXSCSI interface error
1. SCSI signal cable
2. Check power supply
3. SCSI device
4. SCSI adapter card, if installed
5. installed System board
030-195-XXXSCSI interface Test aborted by
user
1. Information
030-196-XXXSCSI interface test halt, error
threshold exceeded
1. Press F3 to review the log file
2. Re-start the test, if necessary
2. Re-start the test to reset the log file
Chapter 1. IBM PC Enhanced Diagnostics error codes
13
Diagnostic Error Code
FRU/Action
030-197-XXXSCSI interface test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
030-198-XXXSCSI interface test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
030-199-XXXSCSI interface test failed, cause
unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
035-000-XXXRAID interface Test Passed
1. No action
035-0XX-XXXRAID interface Failure
1. RAID signal cable
2. RAID device
3. RAID adapter card, if installed
4. System board
035-195-XXXRAID interface Test aborted by
user
1. Information
035-196-XXXRAID interface test halt, error
threshold exceeded
1. Press F3 to review the log file
035-197-XXXRAID interface test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-start the test, if necessary
2. Re-start the test to reset the log file
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
035-198-XXXRAID interface test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
035-199-XXXRAID interface test failed, cause
unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
071-000-XXXAudio port Interface Test Passed
14
6649
1. No action
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Diagnostic Error Code
FRU/Action
071-00X-XXX
071-01X-XXX
071-02X-XXX
Audio port error
1. Run Setup
071-03X-XXXAudio port failure
1. Speakers
2. Flash the system
3. System board
2. Microphone
3. Audio card, if installed
4. System board
071-04X-XXXAudio port failure
1. Run Setup
2. Audio card, if installed
3. System board
071-195-XXXAudio port Test aborted by user
1. Information
2. Re-start the test, if necessary
071-196-XXXAudio port test halt, error
threshold exceeded
1. Press F3 to review the log file
071-197-XXXAudio port test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-start the test to reset the log file
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
071-198-XXXAudio port test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
071-199-XXXAudio port test failed, cause
unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
071-25X-XXXAudio port failure
1. Speakers
2. Audio card, if installed
3. System board
080-000-XXXGame Port interface Test Passed
1. No action
080-XXX-XXXGame Port interface Error
1. Remove the game port device and re-test the
system
080-195-XXXGame Port interface Test aborted
by user
1. Information
2. Re-start the test, if necessary
Chapter 1. IBM PC Enhanced Diagnostics error codes
15
Diagnostic Error Code
FRU/Action
080-196-XXXGame Port interface test halt,
error threshold exceeded
1. Press F3 to review the log file
080-197-XXXGame Port interface test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-start the test to reset the log file
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
080-198-XXXGame Port interface test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
080-199-XXXGame Port interface test failed,
cause unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
086-000-XXXMouse Port interface Test Passed
1. No action
086-001-XXXMouse Port interface Presence
1. Mouse
2. System board
086-032-XXXMouse Port interface Device
controller failure
1. Mouse
086-035-XXXMouse Port interface Reset
1. Mouse
2. System board
2. System board
086-040-XXXMouse Port interface IRQ failure
1. Run Setup
2. Mouse
3. System board
086-195-XXXMouse Port interface Test aborted
by user
1. Information
086-196-XXXMouse Port interface test halt,
error threshold exceeded
1. Press F3 to review the log file
2. Re-start the test, if necessary
2. Re-start the test to reset the log file
086-197-XXXMouse Port interface test warning 1. Make sure the component that is called out is
connected and/or enabled
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
16
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Diagnostic Error Code
FRU/Action
086-198-XXXMouse Port interface test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
086-199-XXXMouse Port interface test failed,
cause unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
089-000-XXXMicroprocessor Test Passed
1. No action
089-XXX-XXXMicroprocessor failure
1. Microprocessor(s)
2. System board
089-195-XXXMicroprocessor Test aborted by
user
1. Information
089-196-XXXMicroprocessor test halt, error
threshold exceeded
1. Press F3 to review the log file
089-197-XXXMicroprocessor test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-start the test, if necessary
2. Re-start the test to reset the log file
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
089-198-XXXMicroprocessor test aborted
1. Flash the system and re-test
2. Go to the ″Undetermined problems″ section
089-199-XXXMicroprocessor test failed, cause
unknown
1. If a component is called out, make sure it is
connected and/or enabled
2. Go to the ″Undetermined problems″ section
3. Flash the system and re-test
4. Replace component under function test
170-000-XXXVoltage Sensor(s) Test Passed
1. No action
170-0XX-XXXVoltage Sensor(s) failure
1. Flash system
2. System board
170-195-XXXVoltage Sensor(s) Test aborted by
user
1. Information
170-196-XXXVoltage Sensor(s) test halt, error
threshold exceeded
1. Press F3 to review the log file
2. Re-start the test, if necessary
2. Re-start the test to reset the log file
Chapter 1. IBM PC Enhanced Diagnostics error codes
17
Diagnostic Error Code
FRU/Action
170-197-XXXVoltage Sensor(s) test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
170-198-XXXVoltage Sensor(s) test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to the ″Undetermined problems″ section
170-199-XXXVoltage Sensor(s) test failed, cause 1. Go to the ″Undetermined problems″ section
unknown
2. Flash the system and re-test
3. Replace component under function test
170-250-XXX
170-251-XXXVoltage Sensor(s) Voltage limit
error
1. Power supply
170-254-XXXVoltage Sensor(s) Voltage
Regulator Module error
1. Voltage Regulator Module (VRM)
2. System board
2. Microprocessor
3. System board
175-000-XXXThermal Sensor(s) Test Passed
1. No action
175-0XX-XXXThermal Sensor(s) failure
1. Flash system
2. System board
175-195-XXXThermal Sensor(s) Test aborted by 1. Information
user
2. Re-start the test, if necessary
175-196-XXXThermal Sensor(s) test halt, error
threshold exceeded
1. Press F3 to review the log file
175-197-XXXThermal Sensor(s) test warning
1. Make sure the component that is called out is
connected and/or enabled
2. Re-start the test to reset the log file
2. Re-run test
3. Component that is called out in warning statement
4. Component under test
175-198-XXXThermal Sensor(s) test aborted
1. If a component is called out, make sure it is
connected and/or enabled
2. Flash the system and re-test
3. Go to ″Undetermined problems″ section
18
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Diagnostic Error Code
FRU/Action
175-199-XXXThermal Sensor(s) test failed,
cause unknown
1. Go to the ″Undetermined problems″ section
2. Flash the system and re-test
3. Replace component under function test
175-250-XXX
175-251-XXXThermal Sensor(s) limit error
1. Check fans
2. Check Power supply
3. Microprocessor
4. System board
185-000-XXXAsset Security Test Passed
1. No action
185-XXX-XXXAsset Security failure
1. Flash system
2. System board
185-278-XXXAsset Security Chassis Intrusion
1. Assure Asset Security Enabled
2. C2 Cover Switch
3. System board
201-000-XXXSystem Memory Test Passed
1. No action
201-XXX-XXXSystem Memory error
1. Replace the memory module called out by the
test
2. System board
202-000-XXXSystem Cache Test Passed
1. No action
202-XXX-XXXSystem Cache error
1. Cache, if removable
2. System board
3. Microprocessor
206-000-XXXDiskette Drive Test Passed
1. No action
206-XXX-XXXDiskette Drive error
1. Diskette Drive Cable
2. Check power supply voltages
3. Diskette drive
4. System board
215-000-XXXCD-ROM Drive Test Passed
1. No action
215-XXX-XXXCD-ROM Drive error
1. CD-ROM Drive Cable
2. Check power supply voltages
3. CD-ROM drive
4. System board
217-000-XXXHard Disk Drive Test Passed
1. No action
Chapter 1. IBM PC Enhanced Diagnostics error codes
19
Diagnostic Error Code
FRU/Action
217-25X-XXX
217-26X-XXXHard Disk Drive (IDE) error
1. Hard Disk Drive Cable
2. Check power supply voltages
3. Hard Disk drive (IDE)
4. System board
217-28X-XXX
217-29X-XXXHard Disk Drive (SCSI) error
1. Hard Disk Drive Cable
2. Check power supply voltages
3. Hard Disk drive (SCSI)
4. SCSI adapter card
5. System board
220-000-XXXHi-Capacity Cartridge Drive Test
Passed
1. No action
220-XXX-XXXHi-Capacity Cartridge Drive
error
1. Remove the Hi-Capacity Cartridge Drive and
re-test the system
301-XXX-XXXKeyboard error
1. Keyboard
2. Check and test mouse
3. System board
301-000-XXXKeyboard Test Passed
1. No action
302-000-XXXMouse Test Passed
1. No action
302-XXX-XXXMouse error
1. Mouse
2. Check and test Keyboard
3. System board
303-000-XXXJoystick Test Passed
1. No action
303-XXX-XXXJoystick error
1. Remove the Joystick and re-test the system
305-000-XXXMonitor DDC Test Passed
1. No action
305-250-XXXMonitor DDC self test failure
1. Run Setup to enable DDC
2. Cable
3. Monitor
4. Video card
5. System board
415-000-XXX
Modem Test Passed
1. No action
415-XXX-XXXModem error
1. Remove the Modem and re-test the system
20
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Chapter 2. Types 6568/6569/6648/6649
Product description . . . . . . . . .
Specifications Information (ISO/ANSI) . .
Specifications - Types
6568/6569/6648/6649 . . . . . . . .
General checkout . . . . . . . . . .
Module test menu and hardware
configuration report . . . . . . . .
Keyboard . . . . . . . . . . . .
Printer . . . . . . . . . . . . .
Power supply . . . . . . . . . .
20-pin main power supply connection . .
Display . . . . . . . . . . . .
Diagnostics, test and recovery information . .
Power-On Self-Test (POST) . . . . . .
POST beep codes . . . . . . . . .
Error code format . . . . . . . . .
Product Recovery Program menu . . . .
IBM PC Enhanced Diagnostics . . . . .
Enhanced Diagnostics download or
diskette . . . . . . . . . . .
Navigating through the diagnostics
programs . . . . . . . . . . .
Running diagnostics tests . . . . .
Test selection. . . . . . . . . .
IBM PC Enhanced Memory Diagnostics
Alert-On LAN™ test . . . . . . .
Asset ID™ test . . . . . . . . .
Test results . . . . . . . . . .
Hard file Smart test . . . . . . .
IBM Fixed Disk Optimized Test . . .
Quick and Full erase - hard drive . . .
Iomega Zip drive test . . . . . . .
Asset EEPROM backup . . . . . .
Viewing the test log . . . . . . .
SIMM/DIMM/RIMM memory errors
Setup Utility program . . . . . . . .
Hard disk drive boot error . . . . . .
When to use the Low-Level Format
program . . . . . . . . . . . .
Preparing the hard disk drive for use . .
Additional service information . . . . . .
Replacing a processor . . . . . . . .
Replacing a system board . . . . . .
Security features . . . . . . . . .
Passwords . . . . . . . . . .
© Copyright IBM Corp. 2000
23
24
24
26
28
29
29
30
31
32
33
33
33
34
34
35
35
36
36
36
36
37
37
37
38
38
39
40
40
40
40
41
42
42
43
44
45
45
46
46
Power-on password . . . . . .
Removing a power-on password . .
Administrator password . . . . .
Administrator password control . .
Operating system password . . . .
Vital product data . . . . . . . .
Management Information Format (MIF)
Alert on LAN . . . . . . . . .
Hard disk drive jumper settings . . . .
CD-ROM drive jumper settings . . . .
BIOS levels . . . . . . . . . . .
Flash (BIOS/VPD) update procedure. . .
Flash recovery boot block jumper . . . .
Power management . . . . . . . .
Automatic configuration and power
interface (ACPI) BIOS . . . . . . .
Advanced Power Management . . . .
Automatic Hardware Power
Management features . . . . . . .
Setting Automatic Hardware Power
Management features . . . . . . .
Automatic Power-On features . . . .
Network settings . . . . . . . . .
Flash over LAN (update POST/BIOS
over network) . . . . . . . . .
Wake on LAN . . . . . . . . .
System board memory . . . . . . .
Supported memory configuration . . .
Computer exploded view Types 6568/6569/6648/6649 . . . . . .
Input/Output connectors . . . . . .
Cover removal . . . . . . . . . .
Replacing the cover . . . . . . . .
EMC shield (CD-ROM drive bay) . . . .
EMC shield (system board) . . . . . .
Installing adapters . . . . . . . . .
Adapter slots . . . . . . . . .
CD-ROM drive removal and replacement
Internal drive removal . . . . . . .
3.5″ drive removal . . . . . . . .
Hard drive removal . . . . . . .
Fan/speaker bracket removal . . . . .
Power supply removal . . . . . . .
Components of the riser card . . . . .
A40 and A40P system board layout . . . .
46
46
47
47
47
47
47
48
48
49
49
50
50
51
51
51
52
52
53
53
54
54
55
55
55
56
57
57
58
58
59
59
60
63
63
64
64
65
65
67
21
System board locations . . . . . .
A40/A40P System board jumper settings
A40/A40P Clear CMOS/Flash Boot
Block Recovery . . . . . . . .
A40/ A40P Processor Speed Settings .
A40/A40P Diskette Write Access . .
Symptom-to-FRU index . . . . . . .
Beep symptoms . . . . . . . . .
No-beep symptoms . . . . . . .
POST error codes . . . . . . . .
Miscellaneous error messages . . . .
22
6649
. 67
67
.
.
.
.
.
.
.
.
67
68
68
69
70
72
72
87
Undetermined problems . . . . . . .
Model tables - Country/Region/Language .
Parts - Types 6568/6569/6648/6649 . . .
Parts listing . . . . . . . . . .
Keyboards - 6568/6569
(PCNext Lite Pearl White) . . . .
Keyboards - 6648/6649
(PCNext Lite Black) . . . . . .
Computer Power Cords . . . . .
Display and Monitor Information . .
Special tools . . . . . . . . . .
.
.
.
.
90
91
92
93
. 95
.
.
.
.
96
98
98
98
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Product description
The NetVista type 6568/6569/6648/6649 computers are available in 2 x 3 (two
I/O adapter slots plus Ethernet, and three drive bays).
v Type 6568 and 6569 are the white desktop types with the A40 and A40P
system boards, respectively.
v Type 6648 and 6649 are the black desktop types with the A40 and A40P
system boards, respectively.
v Security
–
–
–
–
–
Administrator password
Cover lock
Power-on password
Operating system password
U-bolt and cable (optional for some models)
v CMOS backup battery (lithium)
v Common parts
–
–
–
–
–
Diskette drive
Hard disk drive
Keyboard
Power supply
Mouse
Chapter 2. Types 6568/6569/6648/6649
23
Specifications Information (ISO/ANSI)
The machine type specifications information on the following pages was
determined in controlled acoustical environments according to procedures
specified by the American National Standards Institute (ANSI) S12.10 and ISO
7779, and are reported in accordance with ISO 9296. Actual sound pressure
levels in your location might differ from the average values stated because of
room reflections and other nearby noise sources. The declared sound power
levels indicate an upper limit, below which a large proportion of machines
will operate.
Specifications - Types 6568/6569/6648/6649
Feature
Description
Size
Depth: 360 mm (14.2 inches)
Height: 87 mm (3.43 inches)
Width: 345 mm (13.6 inches)
Weight
Minimum configuration as shipped:
8.2 kg (18 lb)
Maximum configuration as shipped:
8.6 kg (19 lb)
Environment
Air temperature:
v System on: 10 to 35 C
(50 to 95 F)
v System off: 10 to 43 C
(50 to 110 F)
Humidity:
v System on: 8% to 80%
v System off: 8% to 80%
Maximum altitude: 2134 m (7000 ft.)
Heat Output
Approximate heat output in BTUs per hour:
v Minimum:
205 BTU/hr. (60 watts)
v Maximum:
375 BTU/hr. (110 watts)
24
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Feature
Description
Electrical Input
Sine-wave input (47 to 63 Hz) required
Input voltage range:
v Minimum: 90 V AC
v Maximum: 265 V AC
Input kVA (approximately):.
v Minimum: 0.08 kVA
v Maximum: 0.16 kVA (as shipped)
Airflow
Approximately 0.25 cubic meters/minute (9 cubic feet/minute)
Acoustical Noise Emission
Values
Average sound pressure levels:
At operator position:
v 43 dB operating
v 38 dB idle
At bystander position (1 meter):
v 37 dB operating
v 33 dB idle
Declared (upper limit) sound power levels:
v 5.1 bels operating
v 4.8 bels idle
For additional information, see the ISO Supplier’s Declaration, which is
available from IBM.
Chapter 2. Types 6568/6569/6648/6649
25
General checkout
This general checkout procedure is for type 6568/6569/6648/6649 computers.
Attention:
The drives in the computer you are servicing might have been
rearranged or the drive startup sequence changed. Be extremely
careful during write operations such as copying, saving or
formatting. Data or programs can be overwritten if you select an
incorrect drive.
Diagnostic error messages appear when a test program finds a problem with a
hardware option. For the test programs to properly determine if a test Passed,
Failed or Aborted, the test programs check the error-return code at test
completion. See “IBM PC Enhanced Diagnostics” on page 35.
General error messages appear if a problem or conflict is found by an
application program, the operating system, or both. For an explanation of
these messages, refer to the information supplied with that software package.
Notes:
1.
Type 6568/6569/6648/6649 computers default to come up quiet (no beep
and no memory count and checkpoint code display) when no errors are
detected by POST.
To enable beep and memory count and checkpoint code display when a
successful POST occurs, do the following:
a. Select Start Options in the Configuration/Setup Utility program (see
“Setup Utility program” on page 41).
b. Set Power-On Self-Test to Enhanced.
2. Before replacing any FRUs, ensure that the latest level of BIOS is installed
on the system. A down-level BIOS might cause false errors and
unnecessary replacement of the system board. For more information on
how to determine and obtain the latest level BIOS, see “BIOS levels” on
page 49.
3. If multiple error codes are displayed, diagnose the first error code
displayed.
4. If the computer hangs with a POST error, go to “Symptom-to-FRU index”
on page 69.
5. If the computer hangs and no error is displayed, go to “Undetermined
problems” on page 90.
6. If an installed device is not recognized by the diagnostics program, that
device might be defective.
26
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
001
1. Power-off the computer and all external devices.
2. Check all cables and power cords.
3. Make sure the system board is seated properly.
4.
5.
6.
7.
8.
Set all display controls to the middle position.
Power-on all external devices.
Power-on all external devices.
Power-on the computer.
Check for the following response:
v Readable instructions or the Main Menu.
DID YOU RECEIVE THE CORRECT RESPONSE?
If NO, continue to 002.
If YES, proceed to 003.
002
If the Power Management feature is enabled, do the following:
1. Start the Configuration/Setup Utility program (see “Setup Utility
program” on page 41)
2. Select Power Management from the Configuration/Setup Utility program
menu.
3. Select APM.
4. Be sure APM BIOS Mode is set to Disabled. If it is not, press Left Arrow
(}) or Right Arrow (Æ) to change the setting.
5. Select Automatic Hardware Power Management.
6. Set Automatic Hardware Power Management to Disabled.
- or Go to “IBM PC Enhanced Diagnostics” on page 35.
003
Run the IBM PC Enhanced Diagnostics test. If necessary, refer to “Diagnostics,
test and recovery information” on page 33.
v If you receive an error, replace the part that the diagnostic program calls
out or go to “IBM PC Enhanced Diagnostics” on page 35.
v If the test stops and you cannot continue, replace the last device tested.
Chapter 2. Types 6568/6569/6648/6649
27
v If the computer has incorrect keyboard responses, go to “Keyboard” on
page 29.
v If the printer has incorrect responses, go to “Printer” on page 29.
v If the display has problems such as jittering, rolling, shifting, or being out
of focus, go to “Display” on page 32.
Module test menu and hardware configuration report
Depending on the diagnostics version level you are using, the installed
devices in the computer are verified in one of two ways.
1. At the start of the diagnostic tests, the Module Test Menu is displayed.
Normally, all installed devices in the computer are highlighted on the
menu.
2. At the start of the diagnostic tests, the main menu appears. From this
menu, select System Info, then select Hardware Configuration from the
next menu. Normally, all installed devices in the computer are highlighted
on this report.
If an installed device is not recognized by the diagnostics program, then
review the following:
v The diagnostic code for the device is not in the Enhanced Diagnostics
utility. Run the diagnostics provided with that device.
v The missing device is defective or it requires an additional diskette or
service manual.
v An unrecognizable device is installed.
v A defective device is causing another device not to be recognized.
v The SCSI controller failed (on the system board or SCSI adapter).
v Use the procedure in “Undetermined problems” on page 90 to find the
problem.
If a device is missing from the list, replace it. If this does not correct the
problem, use the procedure in “Undetermined problems” on page 90.
28
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Keyboard
Note: If a mouse or other pointing device is attached, remove it to see if the
error symptom goes away. If the symptom goes away, the mouse or
pointing device is defective.
001
- Power-off the computer.
Disconnect the keyboard cable from the system unit.
Power-on the computer and check the keyboard cable connector on the
system unit for the voltages shown.
All voltages are 5%.
Pin
1
2
3
4
5
6
Voltage (Vdc)
+5.0
Reserved
Ground
+5.0
+5.0
Reserved
6
5
3
4
2
1
ARE THE VOLTAGES CORRECT?
If NO, continue with 002.
If YES, proceed to 003.
002
Replace the system board.
003
On keyboards with a detachable cable, replace the cable. If the problem
remains or if the cable is permanently attached to the keyboard, replace the
keyboard. If the problem remains, replace the system board.
Printer
1. Make sure the printer is properly connected and powered on.
2. Run the printer self-test.
If the printer self-test does not run correctly, the problem is in the printer.
Refer to the printer service manual.
Chapter 2. Types 6568/6569/6648/6649
29
If the printer self-test runs correctly, install a wrap plug in the parallel port
and run the diagnostic tests to determine which FRU failed.
If the diagnostic tests (with the wrap plug installed) do not detect a failure,
replace the printer cable. If that does not correct the problem, replace the
system board or adapter connected to the printer cable.
Power supply
If the power-on indicator is not on, the power supply fan is not running, or
the computer will not power-off, use the following procedures.
Check/Verify
FRU/Action
Check the following for proper installation.
Reseat
v Power Cord
v On/Off Switch connector
v On/Off Switch Power Supply connector
v System Board Power Supply connectors
v Microprocessor(s) connection
Check the power-on switch for continuity.
Power Cord
Check the power-on switch for continuity.
Power-on Switch
If the above are correct, check the following voltages.
30
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
20-pin main power supply connection
See “A40 and A40P system board layout” on page 67 for connector locations.
Attention
These voltages must be checked with the power supply cables connected
to the system board.
Pin
Signal
Function
1
3.3 V
+3.3 V dc
2
3.3 V
+3.3 V dc
3
COM
Ground
4
5V
+5 V dc
5
COM
Ground
6
5V
+5 V dc
7
COM
Ground
8
POK
Power Good
9
5VSB
Standby Voltage
10
12 V
+12 V dc
11
3.3 V
+3.3 V dc
12
-12 V
-12 V dc
13
COM
Ground
14
PS-ON
DC Remote Enable
15
COM
Ground
16
COM
Ground
17
COM
Ground
18
No voltage
Not used
19
5V
+5 V dc
20
5V
+5 V dc
If the voltages are not correct, and the power cord is good, replace the power
supply.
Chapter 2. Types 6568/6569/6648/6649
31
Display
If the screen is rolling, replace the display assembly. If that does not correct
the problem, replace the video adapter (if installed) or replace the system
board.
If the screen is not rolling, use the following procedure to run the display
self-test.
1. Power-off the computer and display.
2. Disconnect the display signal cable.
3. Power-on the display.
4. Turn the brightness and contrast controls clockwise to their maximum
setting.
5. Check for the following conditions.
v You should be able to vary the screen intensity by adjusting the contrast
and brightness controls.
v The screen should be white or light gray, with a black margin (test
margin) on the screen.
Note: The location of the test margin varies with the type of display. The
test margin might be on the top, bottom, or one or both sides.
If you do not see any test margin on the screen, replace the display. If
there is a test margin on the screen, replace the video adapter (if installed)
or replace the system board.
Note: During the first two or three seconds after the display is powered
on, the following might occur while the display synchronizes with
the computer.
v Unusual patterns or characters
v Static, crackling, or clicking sounds
v A “power-on” hum on larger displays
A noticeable odor might occur on new displays or displays recently
removed from storage.
These sounds, display patterns, and odors are normal. Do not
replace any parts.
If you are unable to correct the problem, go to “Undetermined problems” on
page 90.
32
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Diagnostics, test and recovery information
The following tools are available to help identify and resolve hardware-related
problems.
v Power-On Self-Test (POST)
– POST Beep Codes
– Error Code Format
v IBM PC Enhanced Diagnostics
v Recovery utility
– Full recovery
– Partial recovery
v Repair utility
Power-On Self-Test (POST)
Each time you power-on the system, it performs a series of tests that check
the operation of the system and some options. This series of tests is called the
Power-On Self-Test, or POST. POST does the following operations.
v Checks some basic system-board operations
v Checks the memory operation
v Starts the video operation
v Verifies that the diskette drive is working
v Verifies that the hard disk drive is working
If the POST finishes without detecting any problems, a single beep sounds
and the first screen of the operating system or application program appears.
Note: Type 6568/6569/6648/6649 computers default to come up quiet (no
beep and no memory count and checkpoint code display) when no
errors are detected by POST. To enable beep and memory count and
checkpoint code display when a successful POST occurs, do the
following:
1. Select Start Options in the Configuration/Setup Utility program
(see “Setup Utility program” on page 41).
2. Set Power-On Self-Test to Enhanced.
If the POST detects a problem, an error message appears on the screen. A
single problem can cause several error messages to appear. When you correct
the cause of the first error message, the other error messages probably will not
appear on the screen the next time you turn on the system.
POST beep codes
The Power-On Self-Test generates a beeping sound to indicate successful
completion of POST or to indicate that the tests detect an error.
Chapter 2. Types 6568/6569/6648/6649
33
One beep and the appearance of text on the display indicates successful
completion of the POST. More than one beep indicates that the POST detects
an error.
Error code format
This section provides an explanation of the encoded non-SCSI and SCSI POST
error codes.
Error messages are displayed on the screen as three, four, five, eight, twelve,
or thirteen digits. An X in an error message can be any number or letter. The
shorter POST errors are highlighted in the Symptom-to-FRU Index. Some
digits will represent different information for SCSI errors versus non-SCSI
errors.
The following figure shows which digits display the shorter POST errors. The
figure also defines additional SCSI information.
RDDDPLSCB QEET
Test state
Error code Extension
Qualifier
Bus (0=internal 1=external)
Capacity of the device
Slot number of the device
LUN (usually 0)
PUN (SCSI ID #)
Device Number
Reserved Digit (usually 0)
Notes:
1. Non-IBM device error codes and documentation supersede this list.
2. Duplicate SCSI ID settings will cause misleading error symptoms or
messages.
Product Recovery Program menu
Type 6568/6569/6648/6649 machines have recovery and diagnostics programs
on a separate hard drive partition. The recovery CD and Enhanced
Diagnostics diskette are not shipped with the machine or the HMM. To
download diagnostics tests or to order a recovery CD, see “Enhanced
Diagnostics download or diskette” on page 35.
At startup, after the machine tests the DIMM memory (if Power-on Self Test is
set to Enhanced), the machine displays the following:
To start the Product Recovery Program, press F11
After depressing F11, you are given the following options.
v Full recovery
34
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
This utility reformats the hard drive and restores all original files.
v Partial recovery
This utility reformats the hard drive and restores the Windows operating
system and all device drivers
v Repair
This is the emergency repair utility, and should not be used to install
Windows components.
v System utilities
1. Run diagnostics
This selection accesses the IBM PC Enhanced Diagnostics.
2. System info
3. Create recovery/ repair diskette
IBM PC Enhanced Diagnostics
The IBM PC Enhanced Diagnostics programs use a full range of diagnostic
utilities to determine the operating condition of the computer’s hardware
components.
The diagnostic program includes the following:
v PC-Doctor’s Diagnostic Software
This interface serves as the control program for running both the IBM PC
Enhanced Memory Diagnostics and the suite of diagnostic tests provided by
PC-Doctor.
v IBM PC Enhanced Memory Diagnostics
The memory diagnostic tests determine which memory module (SIMM or
DIMM) is defective and report the socket where the failing module is
located. The Memory diagnostics can run a quick and full test of the
system. Diagnostics can also be run on a single SIMM or DIMM.
Note: See “Chapter 1. IBM PC Enhanced Diagnostics error codes” on page 1
for the specific error codes.
Enhanced Diagnostics download or diskette
The IBM PC Enhanced Diagnostics are available on-line at
http://www.ibm.com/
v Select Support.
v Select Desktop computing from the ″Search by Category″ pull-down menu.
v Select NetVista from the ″Product Family″ list.
v Search for the machine type in the ″Quick Path″ box on the left.
v Select Diagnostics from the ″Downloadable files by Category″ menu or
select the link to PC Enhanced Diagnostics from the ″Downloadable files
by date″ list.
Chapter 2. Types 6568/6569/6648/6649
35
Navigating through the diagnostics programs
Use the cursor movement keys to navigate within the menus.
v The Enter key is used to select a menu item.
v The Esc key is used to back up to the previous menu.
v For online help select F1.
Running diagnostics tests
There are four ways to run the diagnostic tests.
1. Using the cursor movement keys, highlight Run Normal Test or Run
Quick Test from the Diagnostics Menu and then press Enter.
This will automatically run a pre-defined group of tests from each test
category. Run Normal Test runs a more extensive set of tests than does
Run Quick Test and takes longer to execute.
2. Press F5 to automatically run all selected tests in all categories. See ″Test
Selection″.
3. From within a test category, press Ctrl-Enter to automatically run only the
selected tests in that category. See ″Test Selection″.
4. Using the cursor movement keys, highlight a single test within a test
category, then press Enter. This will run only that test.
Press Esc at any time to stop the testing process.
Test results, (N/A, PASSED, FAILED, ABORTED), are displayed in the field
beside the test description and in the test log. See “Viewing the test log” on
page 40.
Test selection
To select one or more tests, use the following procedure.
1. Open the corresponding test category.
2. Using the cursor movement keys, highlight the desired test.
3. Press the space bar.
A selected test is marked by >>. Pressing the space bar again de-selects a
test and removes the chevron.
4. Repeat steps 2 and 3 above to select all desired tests.
IBM PC Enhanced Memory Diagnostics
The IBM PC Enhanced Memory Diagnostics provide the capability to identify
a particular memory module (SIMM or DIMM) which fails during testing. Use
the System Board Layout section to reference the memory sockets, or select F1
twice to load the Online Manual and select Chapter 11, ″SIMM/DIMM/RIMM
Locator″.
36
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Follow the steps below to locate the IBM PC Enhanced Memory Diagnostics
test options.
1. Select the DIAGNOSTICS option on the toolbar and press Enter.
2. Highlight either the Memory Test-Full or Memory Test-Quick option and
press Enter.
3. Memory Test-Full
The full memory test will take about 80 seconds per MB of memory and
will detect marginal, intermittent, and solid (stuck) memory failures.
4. Memory Test-Quick
The quick memory test will take about 20 seconds per MB of memory and
will detect solid (stuck) memory failures only.
Notes
Either level of memory testing can be performed on all memory or a
single SIMM or DIMM socket.
Only sockets containing a SIMM or DIMM can be selected for testing.
Unpopulated sockets are noted by ........ beside the test description.
Alert-On LAN™ test
The Alert On LAN test does the following:
v Determines if Alert On LAN is supported on the system.
v Checks the revision ID register.
v Verifies the EEPROM checksum.
v Validates that a software alert can be sent.
Asset ID™ test
The Asset ID test does the following:
v Determines if Asset ID is supported on the system.
v Verifies the EEPROM areas.
v Performs an antenna detection test.
Test results
IBM PC Enhanced Diagnostic test results will produce the following error
code format:
Function Code
Failure Type
DeviceID
Date
ChkDigits
Text
v Function Code:
Represents the feature or function within the PC.
v Failure Type:
Chapter 2. Types 6568/6569/6648/6649
37
Represents the type of error encountered.
v DeviceID:
Contains the component’s unit-ID which corresponds to either a fixed disk
drive, removable media drive, serial or parallel port, processor, specific
SIMM or DIMM, or a device on the PCI bus.
v Date:
Contains the date on which the diagnostic test was run. The date is
retrieved from CMOS and displayed using the YYYYMMDD format.
v ChkDigits:
Contains a 2-digit check-digit value to ensure the following:
– Diagnostics were run on the specified date.
– Diagnostics were run on the specified IBM computer.
– The diagnostic error code is recorded correctly.
v Text:
Description of the error.
Note
See “Chapter 1. IBM PC Enhanced Diagnostics error codes” on page 1 for
error code listings.
Hard file Smart test
Use the Hard File Smart Test when the system management tool has detected
a hard file SMART alert.
The Smart test does the following:
v Interrogates IDE devices for support of the SMART instruction set.
v Issues a ENABLE SMART command to make sure SMART functionality is
active.
v Checks the SMART RETURN STATUS command to determine if any
thresholds have been exceeded.
If thresholds have been exceeded, an error message is shown, and the test
fails. If no SMART is supported by the drive, the test returns with ″N/A″.
IBM Fixed Disk Optimized Test
You can use the IBM Fixed Disk Optimized Test to identify a particular area
of a hard disk that fails during testing. You can also use this test to correct
types of errors.
To run the Fixed Disk Optimized Test, do the following:
1. From the toolbar, select Diagnostics.
38
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
2. Select Fixed Disk Optimized Test.
3. Select one of the tests:
v Hard Disk Test - Full performs a complete test of the hard disk drive.
v Hard Disk Test - Quick performs a subset of the full hard disk tests.
v Start SMART Hard Disk Test initiates an IDE extended offline self-test.
v SMART Hard Disk Test Results runs the IDE extended offline self-test
and displays the results.
You can run the Start SMART Hard Disk Test and then continue with other
diagnostics tests before running the Hard Drive Self-Test Results.
Quick and Full erase - hard drive
The IBM PC Enhanced Diagnostics Program offers two hard drive format
utilities:
v Quick Erase Hard Drive
v Full Erase Hard Drive
The Quick Erase Hard Drive provides a DOS utility that performs the
following steps.
v Destroys the Master Boot Record (MBR) on the hard drive.
v Destroys all copies of the FAT Table on all partitions (both the master and
backup).
v Destroys the partition table.
v Provides messages that warn the user that this is a non-recoverable process.
The Full Erase Hard Drive provides a DOS utility that performs the following
steps.
v Performs all the steps in Quick Erase.
v Provides a DOS utility that writes random data to all sectors of the hard
drive.
v Provide an estimate of time to completion along with a visual
representation of completion status.
v Provides messages that warn the user about non-recoverable process.
Important
Make sure that the customer backs up all data before using the Quick or
Full Erase function.
To select the Quick Erase or Full Erase Hard Drive utility, use the following
procedure.
Chapter 2. Types 6568/6569/6648/6649
39
1. Select the UTILITY option on the toolbar and press Enter.
2. Select either the QUICK ERASE or FULL ERASE HARD DISK option and
follow the instructions.
Iomega Zip drive test
Use the Iomega Zip Drive Test to test the Zip drive and the drive interface.
The test takes about 20 seconds to run.
The default tests the following:
v Controller
v Max Seek (50 times)
v Random Seek (300 sectors)
Asset EEPROM backup
When replacing a system board, this utility allows the backup of all Asset
information from the EEPROM to diskette. This utility also restores data to
the EEPROM from diskette after replacement of the system board.
To run this utility, use the following procedure.
v Select Utility
v Select Asset EEPROM Backup
v Follow instructions on screen.
Viewing the test log
Errors reported by the diagnostic test will be displayed by the program as a
failed test.
To view details of a failure or to view a list of test results, use the following
procedure from any test category screen.
v Press F3 to activate the log file.
v Press F3 again to save the file to diskette or F2 to print the file.
SIMM/DIMM/RIMM memory errors
SIMM/DIMM/RIMM error messages issued by the IBM PC Enhanced
Diagnostics.
Message
Failure Found
Recommended Actions
2xx-1y
A memory error was detected in
SIMM socket Y.
Replace the SIMM in the socket
identified by the last digit of the
error code.
Re-run the test.
If the same error code occurs
again, replace the system board.
40
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Message
Failure Found
Recommended Actions
2xx-2y
A memory error was detected in
DIMM/RIMM socket Y
Replace the DIMM/RIMM in the
socket identified by the last digit
of the error code.
Re-run the test.
If the same error code occurs
again, replace the system board
or where memory is on the
processor card, replace the
processor card.
Corrupt BIOS
Information in BIOS is not as
expected.
Not able to find expected DMI
information from BIOS.
Reflash the BIOS.
Perform boot block recovery.
Replace the system board.
Memory controller chipset
vendor ID does not match
expected value.
Test aborted by user
User stopped test.
Restart test.
Note: Y is the SIMM/DIMM/RIMM socket number. Use the System Board
Layout section in the latest Hardware Maintenance Manual (HMM) to
reference the memory sockets.
Setup Utility program
Attention
A customized setup configuration (other than default settings) might
exist on the computer you are servicing. Running the Setup Utility
program might alter those settings. Note the current configuration
settings and verify that the settings are in place when service is
complete.
The Setup Utility (configuration) program is stored in the permanent memory
of the computer. This program includes settings for the following:
v System Summary
v
v
v
v
v
Product Data
Devices and I/O Ports
Start Options
Date and Time
System Security
Chapter 2. Types 6568/6569/6648/6649
41
v Advanced Setup
v Power Management
To run the Setup Utility program, use the following procedure.
1. Power-off the computer and wait for a few seconds until all in-use lights
go off.
2. Power-on the computer.
3. When the Setup Utility prompt appears on the screen during start-up,
press F1. The Setup Utility menu will appear.
4. Follow the instructions on the screen.
5. When finished, select System Summary to verify that any configuration
changes have been accepted.
Hard disk drive boot error
A hard disk drive boot error (error codes 1962 and I999030X) can have the
following causes.
Cause
Action
The start-up drive is not in the boot sequence in
configuration.
Check the configuration and ensure the start-up
drive is in the boot sequence.
No operating system installed on the boot drive.
Install an operating system on the boot drive.
The boot sector on the start-up drive is corrupted.
The drive must be formatted, do the following:
1. Attempt to access and recover (back-up) the
failing hard disk drive.
2. Using the operating systems programs, format
the hard disk drive.
3. Go to “Preparing the hard disk drive for use”
on page 43.
The drive is defective.
Replace the hard disk drive.
When to use the Low-Level Format program
Notes
1. The low-level format is not available on all diagnostic diskettes.
2. Before formatting the hard disk drive, make a back-up copy of the
files on the drive to be formatted.
Use the Low-Level Format program in the following situations:
v When you are installing software that requires a low-level format.
v When you get recurring messages from the test programs directing you to
run the Low-Level Format program on the hard disk.
42
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
v As a last resort before replacing a hard disk drive.
Preparing the hard disk drive for use
When the Low-Level Format program is finished, restore to the hard disk all
the files that you previously backed up.
1. Partition the remainder of the hard disk for the operating system. (The
commands vary with the operating system. Refer to the operating system
manual for instructions.)
2. Format the hard disk using the operating system. (The commands vary
with the operating system. Refer to the operating system manual for
instructions.)
3. Install the operating system.
You are now ready to restore the files.
Chapter 2. Types 6568/6569/6648/6649
43
Additional service information
The following additional service information supports types
6568/6569/6648/6649.
v “Replacing a processor” on page 45
v “Replacing a system board” on page 45
v “Security features” on page 46
v “Passwords” on page 46
v “Vital product data” on page 47
v “Management Information Format (MIF)” on page 47
v “Alert on LAN” on page 48
v
v
v
v
v
v
“Hard disk drive jumper settings” on page 48
“CD-ROM drive jumper settings” on page 49
“BIOS levels” on page 49
“Flash (BIOS/VPD) update procedure” on page 50
“Flash recovery boot block jumper” on page 50
“Power management” on page 51
v “Network settings” on page 53
v “Flash over LAN (update POST/BIOS over network)” on page 54
v “Wake on LAN” on page 54
v “System board memory” on page 55
44
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Replacing a processor
Make sure the processor is fully seated in its socket and that the goal post
latches are engaged.
Important
v Make sure the air baffle is installed to prevent processor overheating.
v If the processor is not installed correctly, the system board and the
processor can be damaged.
Replacing a system board
Important
Before replacing a system board, back up Asset information with
PC-Doctor by using the “Asset EEPROM backup” on page 40.
Notes
1. The BIOS and Vital Product Data (VPD) for the computer you are
servicing must be installed on the new system board (FRU) after it is
installed in the computer. To do this, you must run the Flash Update
program using the Flash Update diskette. See “BIOS levels” on
page 49, “Vital product data” on page 47, and “Flash (BIOS/VPD)
update procedure” on page 50.
2. Always ensure the latest level of BIOS is installed on the computer. A
down level BIOS may cause false errors and unnecessary replacement
of the system board.
3. The processor is a separate FRU from the system board and is not
included with the system board FRU. If you are instructed to replace
the system board, use the following procedure.
a. Remove the processor from the old system board and install it on
the new system board.
b. Remove any of the following installed options on the old system
board, and install them on the new system board.
v Memory modules
c. Ensure that the new system board jumper settings match the old
system board jumper settings.
d. If the new system board does not correct the problem, reinstall
the options on the old system board, reinstall the old system
board, then replace the processor.
Chapter 2. Types 6568/6569/6648/6649
45
Security features
Security features in this section include the following:
v Passwords
v Vital Product Data
v Management Information Format (MIF)
v Alert on LAN
Passwords
The following section provides information about computer hardware and
software-related passwords.
v Power-on Password
v Administrator Password
v Operating System Password
Power-on and Administrator passwords are set in the Setup Utility program.
See “Setup Utility program” on page 41 for information about running the
Setup Utility.
Power-on password: A power-on password denies access to the computer by
an unauthorized user when the computer is powered on. When a power-on
password is active, the password prompt appears on the screen each time the
computer is powered on. The computer starts after the proper password is
entered.
Removing a power-on password: To service a computer with an active and
unknown power-on password, power-off the computer and use the following
procedure.
Note
On some models, this procedure will also remove the administrator
password.
1. Unplug the power cord and remove the top cover.
2. Refer to “A40 and A40P system board layout” on page 67 to find the
recovery jumper.
3. Move the recovery jumper from normal to clear.
4. Power-on the computer. The system senses the change in the position and
erases the password. It is necessary to move the jumper back to the previous
position.
5. Remind the user to enter a new password when service is complete.
46
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Administrator password: The administrator password is used to restrict
access to the Configuration/Setup Utility program. If the administrator
password is activated, and you do not enter the administrator password, the
configuration can be viewed but not changed.
Note
Type 6568/6569/6648/6649 has Enhanced Security Mode. If Enhanced
Security mode is enabled and there is no password given, the computer
will act as if Enhanced Security is disabled.
If Enhanced Security is Enabled and an administrator password is given,
the administrator password must be entered to use the computer. If the
administrator password is lost or forgotten, the system board in the
computer must be replaced in order to regain access to the
Configuration/Setup Utility program.
Administrator password control: The Administrator password is set in the
Setup Configuration. Refer to “Setup Utility program” on page 41.
Operating system password: An operating system password is very similar
to a power-on password and denies access to the computer by an
unauthorized user when the password is activated. The computer is unusable
until the password is entered and recognized by the computer.
Vital product data
Each computer has a unique Vital Product Data (VPD) code stored in the
nonvolatile memory on the system board. After you replace the system board,
the VPD must be updated. To update the VPD, see “Flash (BIOS/VPD)
update procedure” on page 50.
Management Information Format (MIF)
Management Information Format (MIF) is a file used to maintain a list of the
system unit serial number along with all serialized components (for example,
system board, riser card, memory, and processor).
At the time of computer manufacture, the EPROM will be loaded with the
serial numbers of the system and all major components. The customer will
have access to the MIF file via the DMI MIF Browser that is installed with the
preload and is also available on the SSCD that is provided with the system.
A company called Retain-a-Group is a central data warehouse offering serial
number data management. Retain-a-Group acts as a focal point to law
enforcement. The customer has the option to purchase serial number
Chapter 2. Types 6568/6569/6648/6649
47
information and services from Retain-a-Group. It is the customer’s
responsibility to maintain the MIF file and to inform Retain-a-Group of any
changes to the file.
Some customers may request their servicers to assist them in maintaining the
MIF file when serialized components are replaced during hardware service.
This assistance is between the customer and the servicer. The servicer can use
the DMI MIF Browser to update the MIF information in the EPROM. It is
anticipated that some servicers might charge for this service.
To update the EPROM using the DMI MIF Browser, use the following
procedure.
1. Click Start from the desktop, then Programs.
2. Select IBM SystemView Agent
3. Select the Serial Number Information icon
4. Click the plus sign to expand.
5. Select the component you want to view or edit.
6. Double click on the component you want to change.
7. Enter new data in the Value field, then click Apply.
Alert on LAN
Alert on LAN provides notification of changes in the computer, even when
®
the computer power is turned off. Working with DMI and Wake on LAN
technologies, Alert on LAN helps to manage and monitor the hardware and
software features of the computer. Alert on LAN generates notifications to the
server of these occurrences:
v Computer disconnected from the network
v Computer unplugged from the power outlet
v All POST errors
v Operating system or POST hang condition
Alert on LAN events are configured to be Enabled or Disabled from the LAN
server only, and not from the computer. See the LAN administrator for
configuration status information.
Hard disk drive jumper settings
IDE hard disk drives for the NetVista series computers use jumpers to set the
drives as primary (master) or secondary (slave).
Note
For drives not shown below, refer to the label on the hard disk drive for
the hard disk drive settings.
48
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
1Primary (Master) Hard Disk Drive
2Secondary (Slave) Hard Disk Drive
CD-ROM drive jumper settings
Type 6568/6569/6648/6649 machines support only the 24X slim CD-ROM
drive. Thus there are no primary versus secondary jumper settings.
BIOS levels
An incorrect level of BIOS can cause false error and unnecessary FRU
replacement. Use the following information to determine the current level of
BIOS installed in the computer, the latest BIOS available for the computer, and
where to obtain the latest level of BIOS.
v Current Level BIOS information
– Run the Configuration Utility to determine the level of BIOS installed.
v Sources for determining the latest level BIOS available
1.
IBM PC Company Home Page
http://www.ibm.com/pc/us/
Chapter 2. Types 6568/6569/6648/6649
49
2. PC PartnerInfo-Technical Database (CTSTIPS.NSF)
®
3. HelpCenter
4. Levels 1 and 2 Support
®
5. RETAIN
v Sources for obtaining the latest level BIOS available
1.
IBM PC Company Home Page
http://www.ibm.com/pc/us/
2. PC PartnerInfo-Technical Database (CTSTIPS.NSF)
3. HelpCenter
4. Levels 1 and 2 Support
To update (flash) the BIOS, see “Flash (BIOS/VPD) update procedure” on
page 50.
Flash (BIOS/VPD) update procedure
Attention
Refer to the information label located inside the system unit cover for
any model-specific information.
1. Power-off the computer.
2. Insert the flash update diskette into drive A.
3. Power-on the computer.
4. When the Update Utility appears; select the country/keyboard, then press
Enter.
5. If the computer serial number was previously recorded, the number is
displayed with an option to update it. Press Y to update the serial number.
6. Type the 7-digit serial number of the computer you are servicing, then
press Enter.
7. Follow the instructions on the screen to complete the flash (BIOS/VPD)
update procedure.
Flash recovery boot block jumper
Attention
If an interruption occurs during a Flash/BIOS upgrade, the BIOS might
be left in an unusable state. The Boot Block jumper enables you to restart
the system and recover the BIOS.
To perform a Flash/BIOS recovery using the recovery jumper, use the
following procedure.
50
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
1. Power-off the computer and remove the cover.
2. Move the system board recovery jumper to the clear position. Refer to
“A40 and A40P system board layout” on page 67 or the label inside the
computer for more information.
3. Insert the upgrade diskette into the diskette drive.
4. Power-on the computer. The IBM Logo will appear.
5. When the Flash Update Utility appears, select the country/keyboard, then
press Enter.
6. If the computer serial number was previously recorded, the number is
displayed with an option to update it. Press Y to update the serial number.
7. Type the 7-digit serial number of the computer you are servicing, then
press Enter.
8. Follow the instructions on the screen to complete the flash (BIOS/VPD)
update procedure.
9. When you are instructed to reboot the computer, power-off the computer
and move the recovery jumper to the normal position. Then replace the
cover and power-on the computer.
Power management
Power management reduces the power consumption of certain components of
the computer such as the system power supply, processor, hard disk drives,
and some monitors. Advanced Power Management and Rapid Resume™
Manager are features of some personal computers.
Automatic configuration and power interface (ACPI) BIOS
Being an ACPI BIOS system, the operating system is allowed to control the
power management features of the computer and the setting for Advanced
Power Management (APM) BIOS mode are ignored. Not all operating systems
support ACPI BIOS mode.
Advanced Power Management
Energy-saving settings can be viewed and changed by using the Advanced
Power Management menu in the Configuration/Setup Utility program.
Attention
If a device, such as a monitor, does not have power-management
capabilities, it can be damaged when exposed to a reduced-power state.
Before making energy-saving selections for the monitor, check the
documentation supplied with the monitor to see if it supports Display
Power Management Signaling (DPMS).
Chapter 2. Types 6568/6569/6648/6649
51
Automatic Hardware Power Management features
Automatic Hardware Power Management can reduce the power states of the
computer, processor, and monitor (if the monitor supports DPMS) if they are
inactive for a predetermined length of time.
There are three levels of specified time that the computer must be inactive
before the power management options that are selected take effect. Select the
amount of time that is offered within each level.
Set time from 5 minutes to 4 hours.
Set time from 10 minutes to 5 hours.
Set time from 15 minutes to 6 hours.
Level 1
Level 2
Level 3
At each level, you can define the amount of energy savings by specifying
values for the following options.
v
System Power
– Select On for the computer to remain on.
– Select Off for the computer to shut down.
v
Processor Speed
Set the microprocessor to be disabled, or to run at 1, 10, 25, or 50 percent of
its internal clock speed.
v
Display
Set display to be disabled or to be reduced at these power states:
– Standby: Screen is blank, but can be restored immediately when any
activity is detected.
– Suspend: Monitor uses less power than in Standby mode. Screen image
is restored after a few seconds when any activity is detected.
– Off: Monitor power is off. Press Monitor power button to restore power.
On some monitors, you might have to depress the power button twice.
Setting Automatic Hardware Power Management features
1. Start the Configuration/Setup Utility program (see “Setup Utility
program” on page 41).
2. Select Advanced Power Management from the Configuration/Setup
Utility program menu.
3. Select the APM BIOS Mode and be sure it is set to Enabled. If it is not,
press Left Arrow (}) or Right Arrow (Æ) to change the setting.
4. Select Automatic Hardware Power Management.
52
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
5. Set Automatic Hardware Power Management to Enabled.
6. Select values for the three categories of power management (system
power, processor speed, and display), as necessary.
7. Set Hard Disk to Enabled or Disabled.
Note: This does not apply to SCSI drives.
8. Press Esc twice to return to the Configuration/Setup Utility program
menu.
9. Before you exit from the program, select Save Settings from the
Configuration/Setup Utility program menu.
10. To exit from the Configuration/Setup Utility program, press Esc and
follow the instructions on the screen.
Automatic Power-On features
The Automatic Power-On features within the Power Management menu allow
you to enable and disable features that turn on the computer automatically.
v Serial Port A Ring Detect: With this feature set to Enabled and an external
modem connected to serial port (COM1), the computer will turn on
automatically when a ring is detected on the modem.
v PCI Modem Ring Detect: With this feature set to Enabled , the computer
will turn on automatically when a ring is detected on the internal modem.
v PCI Wake Up: This feature allow PCI cards that support this capability to
wake the system.
v Wake Up on Alarm: You can specify a date and time at which the
computer will be turned on automatically. This can be either a single event
or a daily event.
v Wake on LAN: If the computer has a properly configured token-ring or
Ethernet LAN adapter card that is Wake on LAN-enabled and there is
remote network management software, you can use the IBM-developed
Wake on LAN feature. When you set Wake on LAN to Enabled, the
computer will turn on when it receives a specific signal from another
computer on the local area network (LAN). For further information, see
“Wake on LAN” on page 54.
Network settings
This section applies only to computers that are linked to a network.
The Configuration/Setup Utility program includes settings that can be
enabled and disabled to configure the network interface in the computer.
These settings are the following:
v Flash over LAN (Update POST/BIOS over Network)
v Wake on LAN
Chapter 2. Types 6568/6569/6648/6649
53
Flash over LAN (update POST/BIOS over network)
Note: For local Flash (BIOS/VPD) update, see “Flash (BIOS/VPD) update
procedure” on page 50.
This setting is used to enable or disable the Flash over LAN feature. When the
feature is enabled, the system programs, in the computer, can be updated
remotely from a network server. If the administrator password is set in the
computer, it does not have to be entered by the server.
To access the Flash over LAN setting, use the following procedure.
1. Start the Configuration/Setup Utility program. See “Setup Utility
program” on page 41.
2. Select System Security.
3. Select POST/BIOS Update from the Configuration/Setup Utility program
menu.
4. To enable Flash over LAN, select Enabled. To disable Flash over LAN,
select Disabled.
5. Press Esc twice to return to the Configuration/Setup Utility program
menu.
6. Before you exit from the program, select Save Settings from the
Configuration/Setup Utility program menu.
7. To exit from the Configuration/Setup Utility program, press Esc and
follow the instructions on the screen.
Wake on LAN
This setting is used to enable or disable the IBM-developed Wake on LAN
feature. This feature makes it possible for the computer to be turned on
remotely by a network server. Remote network management software must be
used in conjunction with this feature.
To access the Wake on LAN setting, use the following procedure.
1. Start the Configuration/Setup Utility program. See “Setup Utility
program” on page 41.
2. Select Advanced Power Management.
3. Select Automatic Power On from the program menu.
4. Select Wake on LAN from the Automatic Power On menu.
5. To enable Wake on LAN, select Enabled. To disable Wake on LAN, select
Disabled.
6. Press Esc until you return to the Configuration/Setup Utility program
menu.
7. Before you exit from the program, select Save Settings from the
Configuration/Setup Utility program menu.
54
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
8. To exit from the Configuration/Setup Utility program, press Esc and
follow the instructions on the screen.
System board memory
The following matrix cross-references the name of the computer (printed on
the logo) and the size, speed, and type of memory modules supported in the
computer.
Computers
Memory Module
Types6568/6569/6648/6649
Size
Speed
Type
64 MB128 MB256
MB
133 MHz
SDRAMNonParityIndustry
Standard
Supported memory configuration
DIMM sizes of 64 MB, 128 MB and 256 MB are acceptable. Start filling DIMM
socket 0, then 1. Use 3.3 V unbuffered 133 MHz SDRAM non-parity DIMMs
only.
Computer exploded view Types 6568/6569/6648/6649
Chapter 2. Types 6568/6569/6648/6649
55
Input/Output connectors
2
1
1Mouse
2USB connector 2
3Parallel connector
4Serial connector 2 (joystick/MIDI connector in
some models)
5Power connector
6Ethernet connector
7Audio output connector
56
6649
8Audio input connector
9Microphone connector
10Monitor connector
11Serial connector 1
12USB connector 1
13Keyboard connector
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Cover removal
Firmly press the cover latch buttons on both sides. Pull up the back end of
cover, and swing the cover toward the front of the computer.
Note
The front panel is integrated with the top cover.
Replacing the cover
Position the cover over the chassis and pivot the cover down over the
computer until the cover snaps into place.
Chapter 2. Types 6568/6569/6648/6649
57
EMC shield (CD-ROM drive bay)
To remove the EMC shield:
1. Remove the front cover.
2. Remove the single screw that holds the EMC shield in place.
EMC shield (system board)
To remove the EMC shield from the system board:
1. Remove the eight I/O screws that hold the EMC shield in place.
58
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Installing adapters
Adapter slots
To install an adapter in a PCI expansion slot:
1. Remove the riser card housing and place the housing on its side with the
adapter slots facing up.
2. Remove the adapter from its static-protective package.
3. Remove the screw and adapter slot cover for the adapter slot into which
you installing the adapter.
4. Install the adapter and insert the retaining screw.
Note: If you are installing a Wake on LAN supported network adapter,
attach the Wake on LAN cable that came with the adapter to the
Chapter 2. Types 6568/6569/6648/6649
59
Wake on LAN connector on the system board. If you also want to
take advantage of the Alert on LAN feature of the computer, you
must install the network adapter in PCI slot 1. For the location of
PCI slot 1 and the Wake on LAN connector, see the diagram of the
system board on the inside of the computer.
5. Replace the riser card housing.
6. Replace the cover.
CD-ROM drive removal and replacement
1. Remove the riser card housing (see “Installing adapters” on page 59).
2. Remove the retaining lever and cable from the rear of the drive.
60
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
3. Remove the CD-ROM drive bracket retaining screw from the front of the
chassis and remove the CD-ROM drive bracket from the drive bay.
4. Install the slimline CD-ROM drive into the drive bay bracket, aligning the
tabs on the bay bracket 1 with the rear of the slimline CD-ROM drive
2and the tiny holes in the drive with the retaining pins in the drive bay
bracket.
5. Press the CD-ROM drive against the retaining spring in the bracket until
the drive is squarely oriented in the bracket and release the drive. You
should hear a slight click as the drive is secured into the bracket.
Chapter 2. Types 6568/6569/6648/6649
61
6. Insert the CD-ROM drive and the bracket into the drive bay and replace
the screw.
7. Install the cable and replace the retaining lever behind the CD-ROM.
62
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Internal drive removal
Note: The internal drive assembly is designed to latch firmly into place.
When pivoting the drive cage out, you will feel some initial resistance,
so you should pull firmly until the drive cage swings out. Inversely,
when you swing the cage back into the machine case, you should feel a
slight resistance until the cage snaps solidly back into place.
1. Pivot the drive bay cage up and toward the front of the computer.
2. Latch the handle to the front of the chassis, so that the drive cage stays
upright.
3.5″ drive removal
1. Remove the two screws from the right side of the drive. Lift the drive out.
Note: Be sure to place the 3.5″ drive cable under the single tab on the bottom
of the drive cage. Press the cable down so that the cable folds
underneath the drive cage, toward the front of the chassis, instead of
folding back toward the system board. This will ensure the 3.5″ drive
cable is not pinched when the drive cage is firmly placed into its
horizontal operating position.
Chapter 2. Types 6568/6569/6648/6649
63
Hard drive removal
1. Latch the drive cage in the upright position.
2. Remove the 3.5″ drive cable from the tab at the bottom of the drive cage.
3. Remove the screw that holds the HD bracket, and lift the tabs that hold
the bracket in place. Lift the drive back and up.
4. Remove the HD cable from the drive and from the bottom of the drive
cage. Note the placement of the cable under the three tabs.
5. Remove the four screws on the side and bottom, and take the HD out of
the bracket.
Note: When replacing the HD in the drive cage, place the cable under the
three tabs at the bottom of the drive cage. Be sure to fold the 3.5″ drive
cable properly under the cage (see ″Note″ in “3.5″ drive removal” on
page 63).
Fan/speaker bracket removal
1. Locate the metal tab that secures the fan/speaker bracket to the chassis (on
the bottom of the bracket, just below the rear end of the speaker).
64
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
2. Press down on the tab, slide the bracket back and lift up.
Power supply removal
1. Remove the CD-ROM drive (see “CD-ROM drive removal and
replacement” on page 60).
2. Remove the two screws that secure the power supply to the front of the
chassis. Remove the two screws that secure the power cord plug to the
back of the chassis.
3. Locate the two tabs that secure the CD-ROM drive bracket to the back of
the power supply. Push in the two tabs and remove the bracket.
4.
Lift out the power supply and plug.
Components of the riser card
The following illustration shows the location of PCI connectors on the riser
card. The Ethernet disable jumper pins (as seen in the diagram below) are
numbered as follows:
Chapter 2. Types 6568/6569/6648/6649
65
v Pin 1 is at the top.
v Pin 2 is in the middle.
v Pin 3 is at the bottom.
To enable Ethernet, jumper pins 1-2. To disable Ethernet, jumper pins 2-3.
1
2
66
6649
PCI slot 1
PCI slot 2
3
Ethernet disable jumper
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
A40 and A40P system board layout
32
31
System board locations
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
#2 fan connector
Microprocessor
DIMM 0
DIMM 1
Power LED connector
RFID connector
Front USB connector
Secondary IDE connector
Diskette connector
Primary IDE connector
Power connector
CMOS clear/recovery jumper
#1 fan connector
Battery
SCSI adapter LED connector
Alert on LAN
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Wake on LAN
PCI slot 3
PCI slot 2
PCI slot 1
AGP connector
CD-ROM audio
Speaker connector
Audio output
Audio input
Serial port 2
Microphone input
Monitor port
Parallel port
Serial port 1
USB connectors
Mouse and keyboard connectors
A40/A40P System board jumper settings
The following table contains the jumper setting information. (D) indicates the
default setting.
A40/A40P Clear CMOS/Flash Boot Block Recovery
Use the recovery jumper setting to Clear CMOS or to Flash Boot Block
Recover.
Chapter 2. Types 6568/6569/6648/6649
67
Note: The A40/A40P CMOS clear/recovery jumper pins are numbered as
follows:
v Pin 1 is the farthest from the battery.
v Pins 2 and 3 are below pin 1, as seen in the A40/A40P System Board
layout.
Jumper
Setting
Description
CMOS Reset
2-3
CMOS Reset/Flash Recovery Mode
1-2 (D)
Normal Mode
A40/ A40P Processor Speed Settings
Processor speed for type 6568/6569/6648/6649 computers are fixed and are
determined by the processor. There are no settings required.
A40/A40P Diskette Write Access
Diskette Write Enable and Write Protect options are changed in the Setup
Configuration. See “Setup Utility program” on page 41.
68
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Symptom-to-FRU index
The Symptom-to-FRU index lists error symptoms and possible causes. The
most likely cause is listed first. Always begin with “General checkout” on
page 26. See “Chapter 1. IBM PC Enhanced Diagnostics error codes” on page 1
when running diagnostics. This index can also be used to help you decide
which FRUs to have available when servicing a computer. If you are unable to
correct the problem using this index, go to “Undetermined problems” on
page 90.
Notes
v If you have both an error message and an incorrect audio response,
diagnose the error message first.
v If you cannot run the diagnostic tests or you get a diagnostic error
code when running a test, but did receive a POST error message,
diagnose the POST error message first.
v If you did not receive any error message, look for a description of
your error symptoms in the first part of this index.
v Check all power supply voltages before you replace the system board.
(See “Power supply” on page 30.)
v Check the hard disk drive jumper settings before you replace a hard
disk drive. (See “Hard disk drive jumper settings” on page 48.)
Important
1.
Some errors are indicated with a series of beep codes (see “Beep
symptoms” on page 70).
Type 6568/6569/6648/6649 computers default to come up quiet (no
beep and no memory count and checkpoint code display) when no
errors are detected by POST. To enable beep and memory count and
checkpoint code display when a successful POST occurs, do the
following:
a. Select Start Options in the Configuration/Setup Utility program
(see “Setup Utility program” on page 41).
b. Set Power-On Self-Test to Enhanced.
2. The processor is a separate FRU from the system board; the processor
is not included with the system board FRU.
Chapter 2. Types 6568/6569/6648/6649
69
Beep symptoms
Beep symptoms are short tones or a series of short tones separated by pauses
(intervals without sound). See the following examples.
Beeps
Description
1-2-X
v One beep
v A pause (or break)
v Two beeps
v A pause (or break)
v Any number of breaks
Four continuous beeps
4
Use the following table to diagnose beep symptoms.
Beep Symptom
FRU/Action
1-1-3CMOS read-write error
1. Run Setup
2. System Board
1-1-4ROM BIOS check error
1. System Board
1-2-XDMA error
1. System Board
1-3-X
1. Memory Module
2. System Board
1-4-4
1. Keyboard
2. System Board
1-4-XError detected in first 64 KB of RAM
1. Memory Module
2. System Board
2-1-1, 2-1-2
1. Run Setup
2. System Board
2-1-XFirst 64 KB of RAM failed
1. Memory Module
2. System Board
2-2-2
1. Video Adapter (if installed)
2. System Board
2-2-XFirst 64 KB of RAM failed
1. Memory Module
2. System Board
2-3-X
1. Memory Module
2. System Board
70
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Beep Symptom
FRU/Action
2-4-X
1. Run Setup
2. Memory Module
3. System Board
3-1-XDMA register failed
1. System Board
3-2-4Keyboard controller failed
1. System Board
2. Keyboard
3-3-4Screen initialization failed
1. Video Adapter (if installed)
2. System Board
Display
3-4-1Screen retrace test detected an error
1. Video Adapter (if installed)
2. System Board
3. Display
3-4-2POST is searching for video ROM
1. Video Adapter (if installed)
2. System Board
4
1. Video Adapter (if installed)
2. System Board
All other beep code sequences
1. System Board
One long and one short beep during POST.Base
640 KB memory error or shadow RAM error
1. Memory Module
One long beep and two or three short beeps
during POST.(Video error)
1. Video Adapter (if installed)
Three short beeps during POST
1. See “System board memory” on page 55
2. System Board
2. System Board
2. System Board
Continuous beep
1. System Board
Repeating short beeps
1. Keyboard stuck key?
2. Keyboard Cable
3. System Board
Chapter 2. Types 6568/6569/6648/6649
71
No-beep symptoms
Note
Type 6568/6569/6648/6649 computers default to come up quiet (no beep
and no memory count and checkpoint code display) when no errors are
detected by POST.
To enable beep and memory count and checkpoint code display when a
successful POST occurs, do the following:
1. Select Start Options in the Configuration/Setup Utility program (see
“Setup Utility program” on page 41).
2. Set Power-On Self Test to Enhanced.
Symptom/Error
FRU/Action
No beep during POST but computer works
correctly.
1. System Board
No beep during POST.
1. See “Undetermined problems” on page 90
2. System Board
3. Memory Module
4. Any Adapter or Device
5. Riser Card
6. Power Cord
7. Power Supply
POST error codes
In the following index, X can represent any number.
POST Error Code
FRU/Action
000SCSI Adapter not enabled
1. Verify adapter device and Bus Master fields
are enabled in PCI configuration program.
See documentation shipped with computer.
02X
1. SCSI Adapter
08XCheck SCSI terminator installation.
1. SCSI Cable
2. SCSI Terminator
3. SCSI Device
4. SCSI Adapter
101System board interrupt failure
1. System Board
102System board timer error
1. System Board
72
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
106
1. System Board
110System board memory parity error
1. Memory Module
2. System Board
111I/O channel parity error
1. Reseat adapters
2. Any adapter
3. Riser card
4. System Board
114Adapter ROM error
1. Adapter Memory
2. System Board
3. Riser card
129Internal cache test error
1. Processor
2. L2 Cache Memory
3. System Board
151Real-time clock failure
1. System Board
161Bad CMOS battery
1. Run Setup
2. CMOS Backup Battery (see “Safety
information” on page 185)
3. System Board
162Configuration mismatch
1. Run Setup and verify Configuration
2. Had a device been added, removed, changed
location? If not, suspect that device.
3. Power-on external devices first, then power-on
computer
4. CMOS Backup Battery (see “Safety
information” on page 185)
System Board
5. System Board
6. Riser card
162And unable to run diagnostics
1. Diskette Drive
2. System Board
3. Diskette Drive Cable
4. Riser card
163Clock not updating or invalid time set
1. Time and Date Set?
2. CMOS Backup Battery (see “Safety
information” on page 185)
3. System Board
Chapter 2. Types 6568/6569/6648/6649
73
POST Error Code
FRU/Action
164POST detected a base memory or extended
memory size mismatch error or RIMM socket 3 is
populated with a RIMM memory module
1. Run Setup. Check System Summary menu for
memory size change. (See “Setup Utility
program” on page 41.)
2. Run the Extended Memory Diagnostic tests
166Boot Block Check Sum Error
1. Run Flash Recovery using Boot Block. See
“Flash recovery boot block jumper” on
page 50.
2. System Board
167Microprocessor installed that is not supported
by the current POST/BIOS
1. Run Setup. Check Stepping level for the
BIOS level needed, then perform the flash
update.
2. Processor
168Alert on LAN error
1. Run Setup. Check to see that Ethernet and
Alert on LAN are enabled.
2. System Board
3. Riser card
17X, 18X
1. C2 Security
175
1. Run Configuration. See “Setup Utility
program” on page 41.
2. System Board
176
1. Covers were removed from the computer
177Corrupted Administrator Password
1. System Board
178
1. System Board
183
1. Enter the administrator password
184No RFID Antenna
1. Make sure Asset Care and Asset ID are
enabled in Configuration/Setup
2. RFID Antenna
3. System Board
4. Riser card
185Corrupted boot sequence
1. Set configuration and reinstall the boot
sequence
186
1. System Board
187
1. Clear Administration password
2. System Board
74
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
189
1. More than three password attempts were
made to access the computer
190Chassis intrusion detector was cleared. This is
information only, no action required. If this code
does not clear:
1. System Board
1XXNot listed above
1. System Board
201, 20XMemory data error
1. Run Enhanced Diagnostics Memory Test
2. Memory Module
3. System Board
225
1. Unsupported Memory
229External cache test error
1. L2 Cache Memory
2. System Board
262POST detected a base memory or extended
memory type error
1. Run Setup. Check System Summary menu for
memory. (See “Setup Utility program” on
page 41.)
2. Run the Extended Memory Diagnostic tests.
301
1. Keyboard
2. Keyboard Cable
3. System Board
303With an 8603 error
1. Mouse
2. Keyboard
3. Keyboard Cable
4. System Board
303With no 8603 error
1. Keyboard
2. Keyboard Cable
3. System Board
3XXNot listed above
1. Keyboard
2. Keyboard Cable
3. System Board
5XX
1. Video Adapter (if installed)
2. System Board
601
1. Diskette Drive A
2. Diskette Drive Cable
3. System Board
4. Riser card
Chapter 2. Types 6568/6569/6648/6649
75
POST Error Code
FRU/Action
602
1. Bad Diskette?
2. Verify Diskette and retry
604And able to run diagnostics
1. Run Setup and verify diskette configuration
settings
2. Diskette Drive A/B
3. Diskette Drive Cable
4. System Board
5. Riser card
605POST cannot unlock the diskette drive
1. Diskette Drive
2. Diskette Drive Cable
3. System Board
4. Riser card
662
1. Diskette drive configuration error or wrong
diskette drive type; run Setup Configuration
6XXNot listed above
1. Diskette Drive
2. System Board
3. Riser card
4. External Drive Adapter
5. Diskette Drive Cable
6. Power Supply
762Math coprocessor configuration error
1. Run Setup
2. Processor
3. System Board
7XX Not listed above
1. Processor
2. System Board
962 Parallel port configuration error
1. Run Configuration
2. Parallel Adapter (if installed)
3. System Board
9XX
1. Printer
2. System Board
1047
76
6649
1. 16-Bit AT™ Fast SCSI Adapter
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
107XCheck SCSI terminator installation
1. Check SCSI terminator installation
2. SCSI Cable
3. SCSI Terminator
4. SCSI Device
5. SCSI Adapter
1101Serial connector error, possible system board
failure
1. Run Enhanced Diagnostics
1101, 1102, 1106, 1108, 1109
1. System Board
2. Any Serial Device
1107
1. Communications Cable
2. System Board
1102Card selected feedback error
1. Run Enhanced Diagnostics
1103Port fails register check
1. Run Enhanced Diagnostics
2. System Board
1106Serial option cannot be turned off
1. Run Enhanced Diagnostics
2. System Board
1107
1. Serial Device Cable
2. System Board
1110Register test failed
1. Run Enhanced Diagnostics
2. System Board
1116Interrupt error
1. Run Enhanced Diagnostics
1117Failed baud rate test
1. Run Enhanced Diagnostics
1162 Serial port configuration error
1. Run Configuration
2. Serial Adapter
(if installed)
3. System Board
11XXNot listed above
1. System Board
1201
1. System Board
2. Any Serial Device
1202, 1206, 1208, 1209, 12XX
1. Dual Async Adapter/A
2. System Board
3. Any Serial Device
Chapter 2. Types 6568/6569/6648/6649
77
POST Error Code
FRU/Action
1207
1. Communications Cable
2. Dual Async Adapter/A
13XX
1. Game Adapter
1402Printer not ready
Information only
1403No paper error, or interrupt failure
Information only
1404System board timeout failure
1. Run Enhanced Diagnostics
1405Parallel adapter error
1. Run Enhanced Diagnostics
1406Presence test error
1. Run Enhanced Diagnostics
14XXNot listed above. Check printer before
replacing system board
1. Printer
15XX
1. SDLC Adapter
1692Boot sequence error
1. Run FDISK to ensure at least one active
partition is set active
16XX
1. 36/38 Workstation Adapter
1762Hard disk drive configuration error
1. Run Configuration (See “Setup Utility
program” on page 41)
1780 (Disk Drive 0)1781 (Disk Drive 1)1782 (Disk
Drive 2)1783 (Disk Drive 3)
1. See “Power supply” on page 30
2. System Board
2. Hard Disk Drive
3. System Board
4. Riser card
5. Hard Disk Cable
6. Power Supply
180X, 188XPCI configuration or resource error
1. Run Setup and verify PCI/ISA configuration
settings.
2. If necessary, set ISA adapters to Not available to
allow PCI adapters to properly configure.
3. Remove any suspect ISA adapters.
4. Rerun diagnostics.
5. PCI Adapter
1962Boot sequence error
1. Possible hard disk drive problem; see “Hard
disk drive boot error” on page 42
209X
1. Diskette Drive
2. Diskette Cable
78
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
20XXNot listed above
1. BSC Adapter
21XX
1. SCSI Device
2. 16-bit AT Fast SCSU adapter
3. Alternate BSC adapter
2401, 2402If screen colors change
1. Display
2401, 2402If screen colors are OK
1. System Board
2. Display
2409
1. Display
2410
1. System Board
2. Display
2462Video memory configuration error
1. Check cable connections
2. Run Setup and verify video configuration
settings
3. Video Memory Modules
4. Video Adapter (if installed)
5. System Board
4611, 4630
1. Multiport/2 Interface Board
2. Multiport/2 Adapter
4612, 4613, 4640, 4641
1. Memory Module Package
2. Multiport/2 Adapter
4650
1. Multiport/2 Interface Cable
46XXNot listed above
1. Multiport/2 Adapter
2. Multiport/2 Interface
Board
3. Memory Module
5600
1. Financial System Controller Adapter
5962An IDE device (other than hard drive)
configuration error
1. Run Configuration
2. CD-ROM Drive
3. CD-ROM Adapter
4. Zip or other ATAPI device
5. System Board
6. Riser card
Chapter 2. Types 6568/6569/6648/6649
79
POST Error Code
FRU/Action
62XX
1. 1st Store Loop Adapter
2. Adapter Cable
63XX
1. 2nd Store Loop Adapter
2. Adapter Cable
64XX
1. Network Adapter
71XX
1. Voice Adapter
74XX
1. Video Adapter
(if installed)
76XX
1. Page Printer Adapter
78XX
1. High Speed Adapter
79XX
1. 3117 Adapter
80XX
1. PCMCIA Adapter
84XX
1. Speech Adapter
2. Speech Control Assy.
8601, 8602
1. Pointing Device (Mouse)
2. System Board
8603, 8604
1. System Board
2. Pointing Device
(Mouse)
86XXNot listed above
1. Mouse
2. System Board
89XX
1. PC Music Adapter
2. MIDI Adapter Unit
91XX
1. Optical Drive
2. Adapter
96XX
1. SCSI Adapter
2. Any SCSI Device
3. System Board
4. Riser card
10101, 10102, 10104, 10105, 10106, 10107, 10108,
10109, 10111,
10112, 10113, 10114,
10115, 10116
80
6649
1. Have customer verify correct operating system
device drivers are installed and operational.
2. Modem
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
10103, 10110, 101171
1. System Board
2. Data/Fax Modem
3. Riser card
10117Not listed above
1. Check system speaker
2. Check PSTN cable
3. External DAA
(if installed)
4. Modem
10118
1. Run Diagnostics and verify the correct
operation of the modem slot
2. Modem
10119
1. Diagnostics detected a non-IBM modem
2. Modem
10120
1. Check PSTN Cable
2. External DAA
(if installed)
3. Modem
10132,
10135,
10138,
10141,
10144,
10147,
10150,
10133,
10136,
10139,
10142,
10145,
10148,
10151,
10134,
10137,
10140,
10143,
10146,
10149,
10152
10153
1. Modem
1. Data/Fax Modem
2. System Board
3. Riser card
101XXNot listed above
1. Modem Adapter/A
2. Data/Fax Modem
3. System Board
4. Riser card
10450, 10451, 10490,
10491, 10492, 10499Read/write error
1. Run Enhanced Diagnostics
2. Hard Disk Drive
3. System Board
4. Riser card
10452Seek test error
1. Run Enhanced Diagnostics
Chapter 2. Types 6568/6569/6648/6649
81
POST Error Code
FRU/Action
10453Wrong drive type?
Information only
10454Sector buffer test error
1. Run Enhanced Diagnostics
10455, 10456Controller error
1. Run Enhanced Diagnostics
10459Drive diagnostic command error
Information only
10461Drive format error
1. Run Enhanced Diagnostics
10462Controller seek error
1. Run Enhanced Diagnostics
10464Hard Drive read error
1. Run Enhanced Diagnostics
10467Drive non-fatal seek error
1. Run Enhanced Diagnostics
10468Drive fatal seek error
1. Run Enhanced Diagnostics
10469Drive soft error count exceeded
1. Run Enhanced Diagnostics
10470, 10471, 10472Controller wrap error
1. Run Enhanced Diagnostics
10473Corrupt data. Low level format might be
required
Information only
10480
1. Hard Disk Drive (ESDI)
2. Drive Cable
3. System Board
10481ESDI drive D seek error
1. Run Enhanced Diagnostics
10482Drive select acknowledgement bad
1. Run Enhanced Diagnostics
106X1
1. Check Configuration
2. Ethernet Adapter
10635
1. Power-off computer, wait ten seconds then
power-on the computer
2. Ethernet Adapter
10651, 10660
1. Check Cables
2. Ethernet Adapter
106XXNot listed above
1. Ethernet Adapter
107XX
1. 5.25-inch External
Diskette Drive
2. 5.25-inch Diskette
Drive Adapter/A
82
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
109XXCheck the adapter cables
1. ActionMedia
Adapter/A
2. System Board
3. Riser card
112XXThis adapter does not have cache
1. SCSI Adapter
2. Any SCSI Device
3. System Board
4. Riser card
119XX
1. 3119 Adapter
121XX
1. Modem Adapter
2. Any Serial Device
3. System Board
4. Riser card
136XX
1. ISDN Primary Rate Adapter
2. System Board
3. Riser card
137XX
1. System Board
141XX
1. Realtime Interface Coprocessor Portmaster
Adapter/A
143XX
1. Japanese Display Adapter
2. System Board
3. Riser card
14710, 14711
1. System Board Video Adapter
2. Adapter Video Memory
148XX
1. Video Adapter
14901, 14902,
1491X, 14922
1. Video Adapter
(if installed)
2. System Board
3. Riser card
4. Display (any type)
14932
1. External Display
2. Video Adapter
161XX
1. FaxConcentrator Adapter
Chapter 2. Types 6568/6569/6648/6649
83
POST Error Code
FRU/Action
164XX
1. 120 MB Internal Tape Drive
2. Diskette Cable
3. System Board
4. Riser card
16500
1. 6157 Tape Attachment
2. Adapter
16520, 16540
1. 6157 Streaming Tape Drive
2. 6157 Tape Attachment Adapter
166XX, 167XX
1. Token Ring Adapter
2. System Board
3. Riser card
18001 to 18029
1. Wizard Adapter
2. Wizard Adapter Memory
18031 to 18039
1. Wizard Adapter Cable
185XXXX
1. DBCS Japanese Display Adapter/A
2. System Board
3. Riser card
20001 to 20003
1. Image Adapter/A
Image-I Adapter/A
2. Memory Module DRAM, VRAM
20004
1. Memory Module DRAM, VRAM
2. Image Adapter/A
Image-I Adapter/A
20005 to 20010
1. Image Adapter/A
Image-I Adapter/A
2. Memory Module DRAM, VRAM
200XXNot listed above
1. Image Adapter/A
2. Image-I Adapter/A
3. Memory Module DRAM, VRAM
4. System Board
5. Riser card
20101 to 20103
1. Printer/Scanner Option
2. Image Adapter/A
3. Memory Module DRAM, VRAM
84
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
20104
1. Memory Module DRAM, VRAM
2. Printer/Scanner Option
3. Image Adapter/A
20105 to 20110
1. Printer/Scanner Option
2. Image Adapter/A
3. Memory Module DRAM, VRAM
Image Adapter/A Memory Test failure indicated
by graphic of adapter
1. Replace memory module (shown in graphic)
206XX
1. SCSI-2 Adapter
2. Any SCSI Device
3. System Board
4. Riser card
208XXVerify there are no duplicate SCSI ID
settings on the same bus.
1. Any SCSI Device
210XXXXInternal bus, size
unknown210XXX1External bus, size unknown
1. SCSI Hard Disk Drive
2. SCSI Adapter or System Board
3. SCSI Cable
4. SCSI ID Switch (on some models)
Tape Drive amber LED remains on
1. Tape Drive
2. SCSI Cable (internal)
3. SCSI Adapter or System Board
Tape Drive green ″in use″ LED fails to come on
1. Tape Drive
2. SCSI Adapter or System Board
3. SCSI Cable (internal)
4. SCSI Cable (external)
Tape automatically ejected from drive
1. Tape Cassette
Drive
SCSI ID on rotary switch does not match SCSI ID
set in configuration. Verify drive switches inside
cover are set to zero
1. Rotary Switch Circuit Board
2. Circuit Board Cable
3. Tape Drive
Tape sticks or breaks in drive. Verify that the tapes 1. Tape Cassette
used meet ANSI standard X3B5
212XX
1. SCSI Printer
2. Printer Cable
213XX
1. SCSI Processor
Chapter 2. Types 6568/6569/6648/6649
85
POST Error Code
FRU/Action
214XX
1. WORM Drive
215XXXC, 215XXXD, 215XXXE, 215XXXUIf an
external device, and power-on LED is off, check
external voltages
1. CD-ROM Drive I
2. CD-ROM Drive II
Enhanced CD-ROM Drive II
Any CD-ROM Drive
3. SCSI Cable
4. SCSI Adapter or System Board
216XX
1. Scanner
217XXIf an external device, and power-on LED is
off, check external voltages
1. Rewritable Optical Drive
2. SCSI Adapter or System Board
3. SCSI Cable
218XXCheck for multi CD tray or jukebox
1. Changer
219XX
1. SCSI Communications Device
24201Y0, 24210Y0Be sure wrap plug is attached
1. ISDN/2 Adapter
2. ISDN/2 Wrap Plug
3. ISDN/2 Communications Cable
273XX
1. 1 Mbps Micro Channel
2.
27501, 27503, 27506, 27507
Infrared LAN Adapter
1. ServerGuard Adapter
2. System Board
3. Riser card
27502, 27504, 27510, 27511, 27533, 27534, 27536,
27537
1. ServerGuard Adapter
27509
1. Remove redundant adapters, run Auto
Configuration program, then retest.
27512
1. WMSELF.DGS diagnostics file is missing
2. WMSELF.DGS diagnostics file is incorrect
27535
1. 3V Lithium Backup Battery
2. ServerGuard Adapter
27554
1. Internal Temperature out of range
2. ServerGuard Adapter
27555, 27556
1. ServerGuard Adapter
2. Power Supply
86
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
27557
1. 7.2V NiCad Main Battery Pack
2. ServerGuard Adapter
27558, 27559, 27560, 27561
1. PCMCIA Type II Modem
2. ServerGuard Adapter
27562
1. External Power Control not connected
2. External Power Control
3. ServerGuard Adapter
27563, 27564
1. External Power Control
2. ServerGuard Adapter
275XX
1. Update Diagnostic Software
27801 to 27879
1. Personal Dictation System
2.
Adapter
3. System Board
27880 to 27889
1. External FRU
(Speaker, Microphone)
999030XHard disk reset failure
1. Possible hard disk drive problem; see “Hard
disk drive boot error” on page 42
Miscellaneous error messages
Message/Symptom
FRU/Action
CMOS Backup Battery inaccurate
1. CMOS Backup Battery (see “Safety
information” on page 185)
2. System Board
Changing colors
1. Display
Computer will not power-off. See “Power supply”
on page 30.
1. Power Switch
2. System Board
3. Riser card
Computer will not RPL from server
1. Ensure that network is in startup sequence as
first device or first device after diskette
2. Ensure that network adapter is enabled for
RPL
3. Network adapter (Advise network
administrator of new MAC address)
Chapter 2. Types 6568/6569/6648/6649
87
Message/Symptom
FRU/Action
Computer will not Wake On LAN (if applicable)
1. Check power supply and signal cable
connections to network adapter
2. Ensure that the operating system settings are
set to enable Wake on LAN
3. Ensure Wake On LAN feature is enabled in
Setup/Configuration (see “Setup Utility
program” on page 41)
4. Ensure network administrator is using correct
MAC address
5. Ensure no interrupt or I/O address conflicts
6. Network adapter (advise network
administrator of new MAC address)
Dead computer. See “Power supply” on page 30.
1. Power Supply
2. System Board
3. Riser card
Diskette drive in-use light remains on or does not
light when drive is active.
1. Diskette Drive
2. System Board
3. Diskette Drive Cable
4. Riser card
Flashing cursor with an otherwise blank display.
1. System Board
2. Primary Hard Disk Drive
3. Hard Disk Drive Cable
4. Riser card
Incorrect memory size during POST
1. Run the Memory tests
2. Memory Module
3. System Board
″Insert a Diskette″ icon appears with a
known-good diagnostics diskette in the first
3.5-inch diskette drive.
1. System Board
2. Diskette Drive Cable
3. Riser card
4. Network Adapter
Intensity or color varies from left to right of
characters and color bars
1. Display
No power or fan not running
1. See “Power supply” on page 30
88
6649
2. System Board
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Message/Symptom
FRU/Action
Non-system disk or disk error-type message with
a known-good diagnostic diskette.
1. Diskette Drive
2. System Board
3. Diskette Drive Cable
4. Riser card
Drives not recognized by the Fixed Disk diagnostic 1. Remove the first drive that does not show up
(e.g., you have six drives but the fixed disk test
and rerun the Fixed Disk diagnostic. If the
only shows three)
remaining drives then show up, replace the
drive you removed.
Hang during Fixed Disk diagnostic
1. Remove the hard file being tested at the time
of the hang.
2. Rerun the diagnostic.
3. If successful, replace the drive you removed.
Other display symptoms not listed above
(including blank or illegible display)
1. See “Display” on page 32
2. System Board
3. Display
Power-on indicator or hard disk drive in-use light
not on, but computer works correctly
1. Power Supply
2. System Board
3. LED Cables
Printer problems
1. See “Printer” on page 29
Program loads from the hard disk with a
known-good diagnostics diskette in the first
3.5-inch diskette drive
1. Run Setup
2. Diskette Drive
3. Diskette Drive Cable
4. System Board
5. Riser card
6. Power Supply
RPL computer cannot access programs from its
own hard disk.
1. If network administrator is using LCCM
Hybrid RPL, check startup sequence:
a. First device - network
b. Second device - hard disk
2. Hard disk drive
RPL computer does not RPL from server
1. Check startup sequence
2. Check the network adapter LED status
Chapter 2. Types 6568/6569/6648/6649
89
Message/Symptom
FRU/Action
Serial or parallel port device failure (system board
port)
1. External Device Self-Test OK?
2. External Device
3. Cable
4. System Board
Serial or parallel port device failure (adapter port)
1. External Device Self-Test OK?
2. External Device
3. Cable
4. Alternate Adapter
5. System Board
Some or all keys on the keyboard do not work
1. Keyboard
2. Keyboard Cable
3. System Board
Undetermined problems
Check the power supply voltages. See “Power supply” on page 30. If the
voltages are correct, return here and continue with the following steps.
1. Power-off the computer.
2. Remove or disconnect the following components (if installed) one at a
time.
Non-IBM devices
External devices (modem, printer, or mouse)
Any adapters
Riser card
Memory modules
Before removing or replacing memory modules, see “System board
memory” on page 55.
f. Extended video memory
g. External Cache
h. External Cache RAM
i. Hard disk drive
j. Diskette drive
3. Power-on the computer to re-test the system.
a.
b.
c.
d.
e.
4. Repeat steps 1 through 3 until you find the failing device or adapter.
If all devices and adapters have been removed, and the problem continues,
replace the system board. See “Replacing a system board” on page 45.
90
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Model tables - Country/Region/Language
Note
For model information, please refer to IBM online at
http://www.ibm.com, then select support to find information for type
6568/6569/6648/6649 models.
Use this table to identify the country/region/language specific models. In
most cases, country/region or language designation will be identified by the
last digit of the model number.
EMEA
Model
EMEA preload
xxG
North America
Model
U.S. English
xxU
Canadian French
xxF
Latin America
Model
Portuguese (Brazil)
xxP
L.A. Spanish
xxS
Asia Pacific (AP)
Model
A.P. English (Australia, New Zealand)
xxA
Japan (Japanese)
xxJ
Hong Kong (A.P. English)
xxD
Hong Kong (Chinese)
xxM
China (Chinese)
xxC
China (A.P. English)
xxD
Thailand (Thai)
xxT
Taiwan (Chinese)
xxV
Chapter 2. Types 6568/6569/6648/6649
91
Parts - Types 6568/6569/6648/6649
92
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Parts listing
Each FRU is available for all types/models, unless specific types or models
are given.
Index
1
2
3
4
4
4
5
5
6
7
8
9
10
10
11
11
12
12
12
12
12
12
12
12
System (Types 6568/6569/6648/6649)
FAN ASM 80MM with FAN/SPEAKER BRACKET (all types/models)
SPEAKER w/CABLE ASM (all types/models)
DASD MOUNTING BRACKET (all types/models)
10.1GB HARDFILE EIDE 5400 RPM (6568 - GAx, GBx, LAx, LBx, NAx,
NBx) (6569/ 6649 - LAx, LBx)(6648 GAx,GBx,LAx,LBx,D2U,D3U,NAx,NBx)
15.0GB HARDFILE EIDE 5400RPM (6568 - D3U)
20.4GB HARDFILE EIDE 5400RPM (6568 - LCx, LDx, PAx, PBx, RAx,
RBx, TAx, TBx, RAA, RBA, RFG,VEG,VCM,VCV, VCD,VDV, KAV, KQV,
KTV, PBV)(6569 - NAx, NBx, PAx, PBx, RAx, RBx, TAx, TBx, RAA,
RBA, RCG, TCG)(6648 - PAx, PBx, RAx, RBx, TAx, TBx, TCU) (6649 NAx, NBx, TAx, PAx, PBx, RAx, RBx, TBx,TCU)
20.4GB HARDFILE EIDE OPTIONAL (6568 - LCx, LDx, PAx, PBx, RAx,
RBx, TAx, TBx, RAA, RBA, RFG,VEG,VCM,VCV,VDV)
TOP COVER ASM with Front Bezel Asm (6568/6569 - all models)
TOP COVER ASM with Front Bezel Asm (6648/6649 only)
3.5″ 1.44MB DISKETTE DRIVE (all types/models)
CD-ROM DRIVE - 24x SLIM(6568 - LCx, LDx, RAx, RBx, NAx, NBx,
TAx, TBx, RAA, RBA, RFG, VEG)(6569 - NAx, NBx, PAx, PBx, RAx,
RBx, TAx, TBx, RAA, RBA, RCG, TCG)(6648 - NAx, NBx, RAx, RBx,
TAx, TBx,TCU) (6649 - NAx, NBx, TAx, TBx, PAx, PBx, RAx, RBx, TCU)
RFID ANTENNA
CDROM BRACKET w/SPRING KIT (all)
110W POWER SUPPLY (6568/6569/6648/6649 - all models)
110W POWER SUPPLY - CHINA (6568 - GAC, GBC, KAV, KQV, KTV,
LAC, LBC, NAC, NBC, PAC, PBC, PBV, TAC, TBC)
SYST BD W/O MEM/PROC/ MERLOT/ W/O POV CARD
(6568/6569/6648/6649)
SYST BD MERLOT W/POV CARD (6569/6649 only)
PIII COPPERMINE 600MHz (6648 - D2U,D3U)
PIII COPPERMINE 667MHz (6568/6648 - GAx, GBx)
PIII COPPERMINE 733MHz (6568 - LAx, LBx, LCx,
LDx)(6569/6648/6649 - LAx, LBx)
PIII COPPERMINE 800MHz (OPTIONAL) (6568/6648/6569/6649 NAx, NBx)
COPPERMINE 866MHz PROCESSOR (6568/6569/6648/6649 - PAx,
PBx)
COPPERMINE 933MHz PROCESSOR (6568 - RAx, RBx,RAA,RBA,RFG)
(6569 - RAx, RBx,RAA,RBA,RCG) (6648/6649 - RAx, RBx)
COPPERMINE 933MHz (6648/6649 - RAx, RBx)
PIll 1GHz PROCESSOR (6568 - TAx, TBx, VEG, VCM, VCV, VCD, VDV,
KQV, KTV) (6569 - TAx, TBx,TCG)(6648/6649 -TAx,TBx,TCU)
FRU No.
22P2473
00N5151
10K0941
36L8681
09N0851
09N0705
06P5240
10K0939
19K5571
06P5229
19K1523
03K9654
10K0937
00N7673
00N7675
09K9982
10K1195
06P7445
10K0863
10K0864
10K1196
19K7539
19K7537
25P0719
24P9479
Chapter 2. Types 6568/6569/6648/6649
93
Index
13
13
13
14
14
15
16
17
94
6649
System (Types 6568/6569/6648/6649)
MEMORY 64MB SDRAM (6568 - GAx, GBx, LAx, LBx, NAx,
NBx)(6569/6649 - LAx, LBx)(6648 - GAx, GBx, LAx, LBx, NAx, NBx)
MEMORY 128MB SDRAM (6568 - LCx, LDx, PAx, PBx, RAx, RBx, TAx,
TBx, D3U, RAA, RBA, RFG, VEG,VCM, VCV, VCD, VDV, KAV, KQV,
KTV, PBV)(6569 - NAx, NBx, PAx, PBx, RAx, RBx, TAx,
TBx,RAA,RBA,RCG,TCG)(6648 - D2U, D3U, PAx, PBx, RAx, RBx, TAx,
TBx)(6649 - NAx, NBx, PAx, PBx, RAx, RBx, TAx, TBx)
MEMORY 256MB SDRAM (6648, 6649 - TCU)
Chassis ASM with FDD Cage (6568/6569 only, all models)
Chassis ASM with FDD Cage (6648/6649 only, all models)
EMC PLANAR SHIELD (all types/models)
RISER CARD ENET (all types/models)
I/O BRACKET ASM (all types/models)
FOOT (5) and VERTICAL STAND (6568/6569 only, all models)
FOOT (5) and VERTICAL STAND (6648/6649 only, all models)
BEZEL KIT with NAMEPLATE (6568/6569 only, all models)
BEZEL KIT with NAMEPLATE (6648/6649 only, all models)
POWER/LED CABLE ASM (all types/models)
KEYLOCK ASM (all types/models)
C2 SWITCH ASM (all types/models)
CABLE HARDFILE - ATA (all types/models)
CABLE DISKETTE DRIVE (all types/models)
MOUSE - 2 Button (6568/6648 - all) (6569 -PAG, PBG, RAx, RBx, TAx,
TBx, RAA, RBA, RCG, TCG) (6649 - TAx, TBx, TCU)
®
MOUSE - Scrollpoint (6569 - NAx, NBx, LAx ,LBx, PAA, PBA)
MOUSE - 2 Button Black (6648 - all) (6649 - TAx, TBx,TCU)
MOUSE - Scrollpoint Black (6649 only - LAx, LBx, NAx, NBx, PAx, PBx,
RAx, RBx)
MOUSE - Scrollpoint Black (6649 - LAx, LBx, NAx, NBx, PAx, PBx,
RAx, RBx)
MISC. HARDWARE KIT (all types/models)
CDROM CABLE (all types/models)
USB CABLE (all types/models)
LITHIUM BATTERY (all types/models)
PLANAR LOCATION LABEL (all types/models)
CELERON 600MHz (6568 - D3U)
COPPERMINE CELERON 800MHz (100 Bus/800MHz/128Kb L2 Cache)
″D0″ STEP LEVEL FLIP CHIP WITH HEATSINK 09N4373 (NOTE:
PRIME P/N TO 10K1196) (6568/ 6569/ 6648/ 6649 - NAx, NBx)
COPPERMINE 866MHz (133/866-256KL2Cache) ″D0″ STEP LEVEL
WITH HEATSINK 09N4373 (PRIME TO 22P4385 AND 19K7539) (6568 PAx, PBx, KAV, PBV) (6648 - PAx,PBx)
COPPERMINE 866MHz (133/866-256KL2Cache) ″C0″ STEP LEVEL
WITH HEATSINK 09N4373 (OPTIONAL) (6568/6648 - PAx,PBx)
FRU No.
33L3072
33L3074
33L3076
06P2950
06P2951
09N5770
09N4515
10K0940
10K0934
19K5569
10K0935
19K5570
10K0942
10K0944
09K9827
10K0829
10K0828
10L6145
09N5535
76H5080
28L1868
09N5537
10K0938
09N0102
09N4496
33F8354
06P2735
06P2442
25P2779
25P2778
22P4385
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Index
System (Types 6568/6569/6648/6649)
HEATSINK NON-IHS 566-866 MHz (6568 - GAx, GBx, LAx, LBx, LCx,
LDx, NAx, NBx, PAx, PBx, KAV, PBV) (6569/6649 - LAx, LBx, NAx,
NBx, PAX, PBx) (6648 - GAx, GBx, LAx, LBx, D2U, D3U, NAx, NBx,
PAx, PBx)
PROCESSOR HEATSINK (6568 - TAx, TBx, VEG, VCM, VCV, VCD,
VDV, KQT, KTV) (6569 - TAx, TBx, RAA, RBA, RCG, TCG)
FAN SINK 900 MHz (6568 - RAx, RBx, RAA, RBA, RFG, TAx, TBx,
VEG, VCM, VCV, VCD, VDV, KQV, KTV) (6569 - RAx, RBx, RAA, RBA,
RCG, TAx, TBx, TCG) (6648/6649 - RAx, RBx, TAx, TBx, TCU)
FANSINK IHS 866-1.10 GHz (6568 - RAx, RBx, RAA, RBA, RFG, TAx,
TBx, VEG, VCM, VCV, VCD, VDV, KQV, KTV) (6569 - RAx, RBx, RAA,
RBA, RCG, TAx, TBx, TCG) (6648/6649 - RAx, RBx, TAx, TBx, TCU)
AIR BAFFLE DUCT (6568 - TAx,TBx,VEG,VCM,VCV, VCD,VDV, KQV,
KTV) (6569 - TAx,TBx,RAA,RBA,RCG,TCG) (6648/ 6649 TAx,TBx,TCU)
FRU No.
09N4372
22P2457
06P2458
22P4370
22P3624
Keyboards - 6568/6569
(PCNext Lite Pearl White)
US ENGLISH
FRENCH CANADIAN 058
FRENCH CANADIAN 044
LA/SPANISH
BRAZIL - PORTUGUESE
ARABIC
BELGIUM - FRENCH
BELGIUM - ENGLISH
BULGARIAN
CZECH
DANISH
DUTCH
FRENCH
GERMAN
GREEK
HEBREW
HUNGARIAN
ITALIAN
NORWEGIAN
POLISH
PORTUGUESE
ROMANIAN
RUSSIAN
SERBIAN - CYR
SLOVAK
SPANISH
37L2514
37L0912
37L2515
37L2516
28L1826
37L2518
37L2519
37L2520
37L2521
37L2522
37L2523
37L2524
37L2525
37L2526
37L2527
37L2528
37L2529
37L2531
37L2532
37L2533
37L2534
37L2535
37L2536
37L2537
37L2538
37L2539
Chapter 2. Types 6568/6569/6648/6649
95
SWEDISH/FINNISH
SWISS - FRENCH/GERMAN
TURKISH - ID 179
TURKISH - ID 440
UK ENGLISH
YUGOSLAVIAN
UK ENGLISH (ISO)
JAPANESE
CHINESE
KOREAN
THAI
37L2540
37L2541
37L2542
37L2543
37L2544
37L2545
37L2546
37L2547
37L2548
28L1860
37L2550
Keyboards - 6648/6649
(PCNext Lite Black)
US ENGLISH
FRENCH CANADIAN 058
FRENCH CANADIAN 044
LA/SPANISH
BRAZIL - PORTUGUESE
ARABIC
BELGIUM - FRENCH
BELGIUM - ENGLISH
BULGARIAN
CZECH
DANISH
DUTCH
FRENCH
GERMAN
GREEK
HEBREW
HUNGARIAN
ICELAND
ITALIAN
NORWEGIAN
POLISH
PORTUGUESE
ROMANIAN
RUSSIAN
SERBIAN - CYR
SLOVAK
SPANISH
SWEDISH/FINNISH
SWISS - FRENCH/GERMAN
TURKISH - ID 179
96
6649
37L2551
37L0913
37L2552
37L2553
37L2554
37L2555
37L2556
37L2557
37L2558
37L2559
37L2560
37L2561
37L2562
37L2563
37L2564
37L2565
37L2566
37L2567
37L2568
37L2569
37L2570
37L2571
37L2572
37L2573
37L2574
37L2575
37L2576
37L2577
37L2578
37L2579
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
TURKISH - ID 440
UK ENGLISH
YUGOSLAVIAN
UK ENGLISH (ISO)
JAPANESE
CHINESE
KOREAN
THAI
37L2580
37L2581
37L2582
37L2583
37L2584
37L2585
28L1905
37L2587
Chapter 2. Types 6568/6569/6648/6649
97
Computer Power Cords
ARABIC
AUSTRALIAN
BELGIAN
BULGARIAN
CANADIAN
CZECH
DENMARK
FINLAND
FRANCE
GERMAN
HUNGARIAN
ISRAEL
ITALIAN
LATIN AMERICAN
NETHERLANDS
NEW ZEALAND
NORWEGIAN
POLISH
PORTUGUESE
SERBIAN
SLOVAKIAN
SOUTH AFRICAN
SPANISH
SWISS
SWISS - FRENCH/GERMAN
US ENGLISH
UK - IRELAND
YUGOSLAVIAN
CHILE
ARGENTINA, PARAGUAY, & URUGUAY
14F0033
93F2365
1339520
1339520
93F2364
1339520
13F9997
1339520
1339520
1339520
1339520
14F0087
14F0069
6952301
1339520
93F2365
1339520
1339520
1339520
1339520
1339520
14F0015
1339520
1339520
14F0051
93F2364
14F0033
1339520
14F0069
36L8880
Display and Monitor Information
Display and monitor information is available separately and is listed under
“Related Publications” on page vii.
Special tools
The following tools are required to service the computer models/types listed
in this section of the service manual
v Volt-ohm meter, IBM P/N 73G5404
v Wrap Plug, IBM P/N 72X8546
98
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Chapter 3. Types 6058/6059/6269/6578/6579
Product description . . . . . . . .
Specifications Information (ISO/ANSI)
Specifications Types 6058/60596269/6578/6579 . . .
General checkout . . . . . . . . .
Module test menu and hardware
configuration report . . . . . . .
Keyboard . . . . . . . . . .
Printer . . . . . . . . . . .
Power supply . . . . . . . . .
20-pin main power supply connection
Display . . . . . . . . . . .
Diagnostics, test and recovery information
Power-On Self-Test (POST) . . . . .
POST beep codes . . . . . . . .
Error code format . . . . . . . .
Product Recovery Program menu . .
IBM PC Enhanced Diagnostics . . .
Enhanced Diagnostics download or
diskette . . . . . . . . . .
Navigating through the diagnostics
programs . . . . . . . . .
Running diagnostics tests . . . .
Test selection . . . . . . . .
IBM PC Enhanced Memory
Diagnostics . . . . . . . . .
Alert-On LAN test . . . . . .
Asset ID test . . . . . . . .
Test results . . . . . . . . .
Hard file Smart test . . . . . .
IBM Fixed Disk Optimized Test . .
Quick and Full erase - hard drive .
Iomega Zip drive test . . . . .
Asset EEPROM backup . . . . .
Viewing the test log . . . . . .
SIMM/DIMM/RIMM memory errors
Setup Utility program . . . . . .
Hard disk drive boot error . . . . .
When to use the Low-Level Format
program . . . . . . . . . . .
Preparing the hard disk drive for use .
Additional service information . . . .
Replacing a processor . . . . . .
Replacing a system board . . . . .
Security features . . . . . . . .
© Copyright IBM Corp. 2000
. 101
102
. 102
. 104
.
.
.
.
.
.
.
.
.
.
106
107
107
108
109
110
111
111
112
112
112
113
. 113
. 114
. 114
. 114
.
.
.
.
.
.
.
.
.
.
115
115
115
115
117
117
119
119
120
120
121
. 122
. 123
.
.
.
.
.
.
123
123
124
125
125
125
Passwords . . . . . . . . .
Power-on password . . . . .
Removing a power-on password
Administrator password . . .
Administrator password control .
Operating system password . .
Vital product data. . . . . . .
Management Information Format
(MIF) . . . . . . . . . . .
Alert on LAN . . . . . . . .
Hard disk drive jumper settings . . .
CD-ROM drive jumper settings . . .
BIOS levels . . . . . . . . . .
Flash (BIOS/VPD) update procedure .
Flash recovery boot block jumper . .
Power management . . . . . . .
Automatic configuration and power
interface (ACPI) BIOS . . . . .
Advanced Power Management . .
Automatic Hardware Power
Management features . . . . .
Setting Automatic Hardware Power
Management features . . . . .
Automatic Power-On features . . .
Network settings . . . . . . . .
Flash over LAN (update POST/BIOS
over network) . . . . . . . .
Wake on LAN . . . . . . . .
System board memory . . . . . .
Supported memory configuration .
Computer exploded view Types 6058/6059/6269/6578/6579 . . .
Input/Output connectors - Type 6269 .
Input/Output connectors - Types
6058/6059/6578/6579 . . . . . .
Cover removal . . . . . . . . .
Replacing the cover . . . . . .
EMC shield (front) . . . . . . .
EMC shield (system board) . . . .
Installing adapters . . . . . . .
Adapter slots . . . . . . . .
Air duct (Types 6058/6059/6278/6279)
CD-ROM drive removal. . . . . .
Fan/speaker bracket removal . . . .
Hard drive removal . . . . . . .
. 126
. 126
126
. 126
. 127
. 127
. 127
.
.
.
.
.
.
.
.
127
128
128
129
129
130
131
131
. 131
. 131
. 132
. 132
. 133
. 133
.
.
.
.
134
135
135
135
. 136
. 137
.
.
.
.
.
.
.
138
139
139
140
140
140
140
141
. 142
. 142
. 143
99
Power supply removal . . . . . .
A20 system board layout (Type 6269) . .
System board locations . . . . . .
A20 System board jumper settings . .
A20 Clear CMOS/Flash Boot Block
Recovery. . . . . . . . . .
A20 Processor Speed Settings . . .
A20 Diskette Write Access . . . .
A40/A40P system board layout
(Types 6058/6059/6578/6579) . . . . .
System board locations . . . . . .
A40/A40P System board jumper settings
A40/A40P Clear CMOS/Flash Boot
Block Recovery . . . . . . .
A40/A40P Processor Speed Settings
100
6649
.
.
.
.
144
146
146
146
. 146
. 147
. 147
. 148
. 148
148
. 149
149
A40/A40P Diskette Write Access. .
Symptom-to-FRU index . . . . . . .
Beep symptoms . . . . . . . .
No-beep symptoms . . . . . . .
POST error codes . . . . . . . .
Miscellaneous error messages . . . .
Undetermined problems . . . . . .
Model tables - Country/Region/Language
Parts - Types 6058/6059/6269/6578/6579
Parts listing . . . . . . . . . .
Keyboards - PCNext Lite Pearl White
Computer Power Cords . . . . .
Recovery CDs . . . . . . . .
Display and Monitor Information .
Special tools . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
149
150
150
152
153
167
171
172
173
174
180
181
182
182
183
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Product description
The NetVista type 6058/60596269/6578/6579 computers are available in 4 x 4
(four I/O adapter slots, four drive bays). Type 6269 has only has 3 usable I/O
slots.
v Type 6269 is the white desktop type with the A20 system board.
v Types 6578 and 6579 are the white desktop types with the A40 and A40P
system boards, respectively.
v Types 6058 and 6059 are the Global machine types, white desktop, with the
A40 and A40P system boards, respectively.
v Security
– Administrator password
– Cover lock
(optional on 6269; not shipped with machine)
– Power-on password
– Operating system password
– U-bolt and cable (optional for some models)
v CMOS backup battery (lithium)
v Common parts
– Diskette drive
– Hard disk drive
– Keyboard
– Power supply
– Mouse
Chapter 3. Types 6058/6059/6269/6578/6579
101
Specifications Information (ISO/ANSI)
The machine type specifications information on the following pages was
determined in controlled acoustical environments according to procedures
specified by the American National Standards Institute (ANSI) S12.10 and ISO
7779, and are reported in accordance with ISO 9296. Actual sound pressure
levels in your location might differ from the average values stated because of
room reflections and other nearby noise sources. The declared sound power
levels indicate an upper limit, below which a large proportion of machines
will operate.
Specifications Types 6058/60596269/6578/6579
Feature
Description
Size
Depth: 425 mm (16.7 inches)
Height: 140 mm (5.5 inches)
Width: 425 mm (16.7 inches)
Weight
Minimum configuration as shipped:
9.4 kg (20 lb)
Maximum configuration as shipped: 11.3 kg (25 lb)
Environment
Air temperature:
v System on: 10 to 35 C
(50 to 95 F)
v System off: 10 to 43 C
(50 to 110 F)
Humidity:
v System on: 8% to 80%
v System off: 8% to 80%
Maximum altitude: 2134 m (7000 ft.)
Heat Output
Approximate heat output in BTUs per hour:
v Minimum:
240 BTU/hr. (75 watts)
v Maximum:
705 BTU/hr. (207 watts)
102
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Feature
Description
Electrical Input
Sine-wave input (47 to 63 Hz) required
Input voltage range:
v Minimum: 90 V AC
v Maximum: 265 V AC
Input kVA (approximately):
v Minimum: 0.08 kVA
v Maximum: 0.30 kVA (as shipped)
Airflow
Approximately 0.5 cubic meters/minute (18 cubic feet/minute)
Acoustical Noise Emission
Values
Average sound pressure levels:
At operator position:
v 43 dB operating
v 38 dB idle
At bystander position (1 meter):
v 37 dB operating
v 33 dB idle
Declared (upper limit) sound pressure levels:
v 5.1 bels operating
v 4.8 bels idle
Chapter 3. Types 6058/6059/6269/6578/6579
103
General checkout
This general checkout procedure is for type 6058/6059/6269/6578/6579
computers.
Attention: The drives in the computer you are servicing might have been
rearranged or the drive startup sequence changed. Be extremely
careful during write operations such as copying, saving or
formatting. Data or programs can be overwritten if you select an
incorrect drive.
Diagnostic error messages appear when a test program finds a problem with a
hardware option. For the test programs to properly determine if a test Passed,
Failed or Aborted, the test programs check the error-return code at test
completion. See “IBM PC Enhanced Diagnostics” on page 113.
General error messages appear if a problem or conflict is found by an
application program, the operating system, or both. For an explanation of
these messages, refer to the information supplied with that software package.
Notes:
1.
Type 6058/6059/6269/6578/6579 computers default to come up quiet (no
beep and no memory count and checkpoint code display) when no errors
are detected by POST.
To enable beep and memory count and checkpoint code display when a
successful POST occurs, do the following:
a. Select Start Options in the Configuration/Setup Utility program (see
“Setup Utility program” on page 122).
b. Set Power-On Self-Test to Enhanced.
2. Before replacing any FRUs, ensure that the latest level of BIOS is installed
on the system. A down-level BIOS might cause false errors and
unnecessary replacement of the system board. For more information on
how to determine and obtain the latest level BIOS, see “BIOS levels” on
page 129.
3. If multiple error codes are displayed, diagnose the first error code
displayed.
4. If the computer hangs with a POST error, go to “Symptom-to-FRU index”
on page 150.
5. If the computer hangs and no error is displayed, go to “Undetermined
problems” on page 171.
6. If an installed device is not recognized by the diagnostics program, that
device might be defective.
104
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
001
1. Power-off the computer and all external devices.
2. Check all cables and power cords.
3. Make sure the system board is seated properly.
4.
5.
6.
7.
8.
Set all display controls to the middle position.
Power-on all external devices.
Power-on all external devices.
Power-on the computer.
Check for the following response:
v Readable instructions or the Main Menu.
DID YOU RECEIVE THE CORRECT RESPONSE?
If NO, continue to 002.
If YES, proceed to 003.
002
If the Power Management feature is enabled, do the following:
1. Start the Configuration/Setup Utility program (see “Setup Utility
program” on page 122)
2. Select Power Management from the Configuration/Setup Utility program
menu.
3. Select APM.
4. Be sure APM BIOS Mode is set to Disabled. If it is not, press Left Arrow
(}) or Right Arrow (Æ) to change the setting.
5. Select Automatic Hardware Power Management.
6. Set Automatic Hardware Power Management to Disabled.
- or Go to the “IBM PC Enhanced Diagnostics” on page 113.
003
Run the IBM PC Enhanced Diagnostics test. If necessary, refer to “Diagnostics,
test and recovery information” on page 111.
v If you receive an error, replace the part that the diagnostic program calls
out or go to “IBM PC Enhanced Diagnostics” on page 113.
v If the test stops and you cannot continue, replace the last device tested.
Chapter 3. Types 6058/6059/6269/6578/6579
105
v If the computer has incorrect keyboard responses, go to “Keyboard” on
page 107.
v If the printer has incorrect responses, go to “Printer” on page 107.
v If the display has problems such as jittering, rolling, shifting, or being out
of focus, go to “Display” on page 110.
Module test menu and hardware configuration report
Depending on the diagnostics version level you are using, the installed
devices in the computer are verified in one of two ways.
1. At the start of the diagnostic tests, the Module Test Menu is displayed.
Normally, all installed devices in the computer are highlighted on the
menu.
2. At the start of the diagnostic tests, the main menu appears. From this
menu, select System Info, then select Hardware Configuration from the
next menu. Normally, all installed devices in the computer are highlighted
on this report.
If an installed device is not recognized by the diagnostics program, then
review the following:
v The diagnostic code for the device is not in the Enhanced Diagnostics
utility. Run the diagnostics provided with that device.
v The missing device is defective or it requires an additional diskette or
service manual.
v An unrecognizable device is installed.
v A defective device is causing another device not to be recognized.
v The SCSI controller failed (on the system board or SCSI adapter).
v Use the procedure in “Undetermined problems” on page 171 to find the
problem.
If a device is missing from the list, replace it. If this does not correct the
problem, use the procedure in “Undetermined problems” on page 171.
106
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Keyboard
Note
If a mouse or other pointing device is attached, remove it to see if the
error symptom goes away. If the symptom goes away, the mouse or
pointing device is defective.
001
- Power-off the computer.
Disconnect the keyboard cable from the system unit.
Power-on the computer and check the keyboard cable connector on the
system unit for the voltages shown.
All voltages are 5%.
Pin
1
2
3
4
5
6
Voltage (Vdc)
+5.0
Reserved
Ground
+5.0
+5.0
Reserved
6
5
3
4
2
1
ARE THE VOLTAGES CORRECT?
If YES, proceed to 003.
If NO, continue with 002.
002
Replace the system board.
003
On keyboards with a detachable cable, replace the cable. If the problem
remains or if the cable is permanently attached to the keyboard, replace the
keyboard. If the problem remains, replace the system board.
Printer
1. Make sure the printer is properly connected and powered on.
2. Run the printer self-test.
Chapter 3. Types 6058/6059/6269/6578/6579
107
If the printer self-test does not run correctly, the problem is in the printer.
Refer to the printer service manual.
If the printer self-test runs correctly, install a wrap plug in the parallel port
and run the diagnostic tests to determine which FRU failed.
If the diagnostic tests (with the wrap plug installed) do not detect a failure,
replace the printer cable. If that does not correct the problem, replace the
system board or adapter connected to the printer cable.
Power supply
If the power-on indicator is not on, the power supply fan is not running, or
the computer will not power-off, use the following procedures.
Check/Verify
FRU/Action
Verify that the voltage-selector switch is set for the Correct the voltage-selector switch setting
correct voltage.
Check the following for proper installation.
Reseat
v Power Cord
v On/Off Switch connector
v On/Off Switch Power Supply connector
v System Board Power Supply connectors
v Microprocessor(s) connection
Check the power-on switch for continuity.
Power Cord
Check the power-on switch for continuity.
Power-on Switch
If the above are correct, check the following voltages.
108
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
20-pin main power supply connection
See “A20 system board layout (Type 6269)” on page 146 or “A40/A40P system
board layout
(Types 6058/6059/6578/6579)” on page 148 for connector locations.
Attention
These voltages must be checked with the power supply cables connected
to the system board.
Pin
Signal
Function
1
3.3 V
+3.3 V dc
2
3.3 V
+3.3 V dc
3
COM
Ground
4
5V
+5 V dc
5
COM
Ground
6
5V
+5 V dc
7
COM
Ground
8
POK
Power Good
9
5VSB
Standby Voltage
10
12 V
+12 V dc
11
3.3 V
+3.3 V dc
12
-12 V
-12 V dc
13
COM
Ground
14
PS-ON
DC Remote Enable
15
COM
Ground
16
COM
Ground
17
COM
Ground
18
No voltage
Not used
19
5V
+5 V dc
20
5V
+5 V dc
Chapter 3. Types 6058/6059/6269/6578/6579
109
If the voltages are not correct, and the power cord is good, replace the power
supply.
Display
If the screen is rolling, replace the display assembly. If that does not correct
the problem, replace the video adapter (if installed) or replace the system
board.
If the screen is not rolling, use the following procedure to run the display
self-test.
1. Power-off the computer and display.
2. Disconnect the display signal cable.
3. Power-on the display.
4. Turn the brightness and contrast controls clockwise to their maximum
setting.
5. Check for the following conditions.
v You should be able to vary the screen intensity by adjusting the contrast
and brightness controls.
v The screen should be white or light gray, with a black margin (test
margin) on the screen.
Note: The location of the test margin varies with the type of display. The
test margin might be on the top, bottom, or one or both sides.
If you do not see any test margin on the screen, replace the display. If
there is a test margin on the screen, replace the video adapter (if installed)
or replace the system board.
Note: During the first two or three seconds after the display is powered
on, the following might occur while the display synchronizes with
the computer.
v Unusual patterns or characters
v Static, crackling, or clicking sounds
v A “power-on” hum on larger displays
A noticeable odor might occur on new displays or displays recently
removed from storage.
These sounds, display patterns, and odors are normal. Do not
replace any parts.
If you are unable to correct the problem, go to “Undetermined problems” on
page 171.
110
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Diagnostics, test and recovery information
The following tools are available to help identify and resolve hardware-related
problems.
v Power-On Self-Test (POST)
– POST Beep Codes
– Error Code Format
v IBM PC Enhanced Diagnostics
v Recovery utility
– Full recovery
– Partial recovery
v Repair utility
Power-On Self-Test (POST)
Each time you power-on the system, it performs a series of tests that check
the operation of the system and some options. This series of tests is called the
Power-On Self-Test, or POST. POST does the following operations.
v Checks some basic system-board operations
v Checks the memory operation
v Starts the video operation
v Verifies that the diskette drive is working
v Verifies that the hard disk drive is working
If the POST finishes without detecting any problems, a single beep sounds
and the first screen of the operating system or application program appears.
Note: Types 6058/6059/6269/6578/6579 computers default to come up quiet
(no beep and no memory count and checkpoint code display) when no
errors are detected by POST.
To enable beep and memory count and checkpoint code display when a
successful POST occurs, do the following:
1. Select Start Options in the Configuration/Setup Utility program
(see “Setup Utility program” on page 122).
2. Set Power-On Self-Test to Enhanced.
If the POST detects a problem, an error message appears on the screen. A
single problem can cause several error messages to appear. When you correct
the cause of the first error message, the other error messages probably will not
appear on the screen the next time you turn on the system.
Chapter 3. Types 6058/6059/6269/6578/6579
111
POST beep codes
The Power-On Self-Test generates a beeping sound to indicate successful
completion of POST or to indicate that the tests detect an error.
One beep and the appearance of text on the display indicates successful
completion of the POST. More than one beep indicates that the POST detects
an error.
Error code format
This section provides an explanation of the encoded non-SCSI and SCSI POST
error codes.
Error messages are displayed on the screen as three, four, five, eight, twelve,
or thirteen digits. An X in an error message can be any number or letter. The
shorter POST errors are highlighted in the Symptom-to-FRU Index. Some
digits will represent different information for SCSI errors versus non-SCSI
errors.
The following figure shows which digits display the shorter POST errors. The
figure also defines additional SCSI information.
RDDDPLSCB QEET
Test state
Error code Extension
Qualifier
Bus (0=internal 1=external)
Capacity of the device
Slot number of the device
LUN (usually 0)
PUN (SCSI ID #)
Device Number
Reserved Digit (usually 0)
Notes:
1. Non-IBM device error codes and documentation supersede this list.
2. Duplicate SCSI ID settings will cause misleading error symptoms or
messages.
Product Recovery Program menu
Types 6058/6059/6269/6578/6579 machines have recovery and diagnostics
programs on a separate hard drive partition. The recovery CD and Enhanced
Diagnostics diskette are not shipped with the machine or the HMM. To
download diagnostics tests or to order a recovery CD, see “Enhanced
Diagnostics download or diskette” on page 113.
112
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
At startup, after the machine tests the DIMM memory, the machine displays
the following:
To start the Product Recovery Program, press F11
After depressing F11, you are given the following options.
v Full recovery
This utility reformats the hard drive and restores all original files.
v Partial recovery
This utility reformats the hard drive and restores the Windows operating
system and all device drivers
v Repair
This is the emergency repair utility, and should not be used to install
Windows components.
v System utilities
1. Run diagnostics
This selection accesses the IBM PC Enhanced Diagnostics.
2. System info
3. Create recovery/ repair diskette
IBM PC Enhanced Diagnostics
The IBM PC Enhanced Diagnostics programs use a full range of diagnostic
utilities to determine the operating condition of the computer’s hardware
components.
The diagnostic program includes the following:
v PC-Doctor’s Diagnostic Software
This interface serves as the control program for running both the IBM PC
Enhanced Memory Diagnostics and the suite of diagnostic tests provided by
PC-Doctor.
v IBM PC Enhanced Memory Diagnostics
The memory diagnostic tests determine which memory module (SIMM or
DIMM) is defective and report the socket where the failing module is
located. The Memory diagnostics can run a quick and full test of the
system. Diagnostics can also be run on a single SIMM or DIMM.
Note: See “Chapter 1. IBM PC Enhanced Diagnostics error codes” on page 1
for the specific error codes.
Enhanced Diagnostics download or diskette
The IBM PC Enhanced Diagnostics are available on-line at
http://www.ibm.com/
v Select Support.
Chapter 3. Types 6058/6059/6269/6578/6579
113
v
v
v
v
Select Desktop computing from the ″Search by Category″ pull-down menu.
Select NetVista from the ″Product Family″ list.
Search for the machine type in the ″Quick Path″ box on the left.
Select Diagnostics from the ″Downloadable files by Category″ menu or
select the link to PC Enhanced Diagnostics from the ″Downloadable files
by date″ list.
Navigating through the diagnostics programs
Use the cursor movement keys to navigate within the menus.
v The Enter key is used to select a menu item.
v The Esc key is used to back up to the previous menu.
v For online help select F1.
Running diagnostics tests
There are four ways to run the diagnostic tests.
1. Using the cursor movement keys, highlight Run Normal Test or Run
Quick Test from the Diagnostics Menu and then press Enter.
This will automatically run a pre-defined group of tests from each test
category. Run Normal Test runs a more extensive set of tests than does
Run Quick Test and takes longer to execute.
2. Press F5 to automatically run all selected tests in all categories. See ″Test
Selection″.
3. From within a test category, press Ctrl-Enter to automatically run only the
selected tests in that category. See ″Test Selection″.
4. Using the cursor movement keys, highlight a single test within a test
category, then press Enter. This will run only that test.
Press Esc at any time to stop the testing process.
Test results, (N/A, PASSED, FAILED, ABORTED), are displayed in the field
beside the test description and in the test log. See “Viewing the test log” on
page 120.
Test selection
To select one or more tests, use the following procedure.
1. Open the corresponding test category.
2. Using the cursor movement keys, highlight the desired test.
3. Press the space bar.
A selected test is marked by >>. Pressing the space bar again de-selects a
test and removes the chevron.
4. Repeat steps 2 and 3 above to select all desired tests.
114
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
IBM PC Enhanced Memory Diagnostics
The IBM PC Enhanced Memory Diagnostics provide the capability to identify
a particular memory module (SIMM or DIMM) which fails during testing. Use
the System Board Layout section to reference the memory sockets, or select F1
twice to load the Online Manual and select Chapter 11, ″SIMM/DIMM/RIMM
Locator″.
Follow the steps below to locate the IBM PC Enhanced Memory Diagnostics
test options.
1. Select the DIAGNOSTICS option on the toolbar and press Enter.
2. Highlight either the Memory Test-Full or Memory Test-Quick option and
press Enter.
3. Memory Test-Full
The full memory test will take about 80 seconds per MB of memory and
will detect marginal, intermittent, and solid (stuck) memory failures.
4. Memory Test-Quick
The quick memory test will take about 20 seconds per MB of memory and
will detect solid (stuck) memory failures only.
Notes:
1. Either level of memory testing can be performed on all memory or a single
SIMM or DIMM socket.
2. Only sockets containing a SIMM or DIMM can be selected for testing.
Unpopulated sockets are noted by ........ beside the test description.
Alert-On LAN test
The Alert On LAN test does the following:
v Determines if Alert On LAN is supported on the system.
v Checks the revision ID register.
v Verifies the EEPROM checksum.
v Validates that a software alert can be sent.
Asset ID test
The Asset ID test does the following:
v Determines if Asset ID is supported on the system.
v Verifies the EEPROM areas.
v Performs an antenna detection test.
Test results
IBM PC Enhanced Diagnostic test results will produce the following error
code format:
Function Code
Failure Type
DeviceID
Date
ChkDigits
Text
Chapter 3. Types 6058/6059/6269/6578/6579
115
v Function Code:
Represents the feature or function within the PC.
v Failure Type:
Represents the type of error encountered.
v DeviceID:
Contains the component’s unit-ID which corresponds to either a fixed disk
drive, removable media drive, serial or parallel port, processor, specific
SIMM or DIMM, or a device on the PCI bus.
v Date:
Contains the date on which the diagnostic test was run. The date is
retrieved from CMOS and displayed using the YYYYMMDD format.
116
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
v ChkDigits:
Contains a 2-digit check-digit value to ensure the following:
– Diagnostics were run on the specified date.
– Diagnostics were run on the specified IBM computer.
– The diagnostic error code is recorded correctly.
v Text:
Description of the error.
Note:
See “Chapter 1. IBM PC Enhanced Diagnostics error codes” on page 1
for error code listings.
Hard file Smart test
Use the Hard File Smart Test when the system management tool has detected
a hard file SMART alert.
The Smart test does the following:
v Interrogates IDE devices for support of the SMART instruction set.
v Issues an ENABLE SMART command to make sure SMART functionality is
active.
v Checks the SMART RETURN STATUS command to determine if any
thresholds have been exceeded.
If thresholds have been exceeded, an error message is shown, and the test
fails. If no SMART is supported by the drive, the test returns with ″N/A″.
IBM Fixed Disk Optimized Test
You can use the IBM Fixed Disk Optimized Test to identify a particular area
of a hard disk that fails during testing. You can also use this test to correct
types of errors.
To run the Fixed Disk Optimized Test, do the following:
1. From the toolbar, select Diagnostics.
2. Select Fixed Disk Optimized Test.
3. Select one of the tests:
v Hard Disk Test - Full performs a complete test of the hard disk drive.
v Hard Disk Test - Quick performs a subset of the full hard disk tests.
v Start SMART Hard Disk Test initiates an IDE extended offline self-test.
v SMART Hard Disk Test Results runs the IDE extended offline self-test
and displays the results.
Chapter 3. Types 6058/6059/6269/6578/6579
117
You can run the Start SMART Hard Disk Test and then continue with other
diagnostics tests before running the Hard Drive Self-Test Results.
118
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Quick and Full erase - hard drive
The IBM PC Enhanced Diagnostics Program offers two hard drive format
utilities:
v Quick Erase Hard Drive
v Full Erase Hard Drive
The Quick Erase Hard Drive provides a DOS utility that performs the
following steps.
v Destroys the Master Boot Record (MBR) on the hard drive.
v Destroys all copies of the FAT Table on all partitions (both the master and
backup).
v Destroys the partition table.
v Provides messages that warn the user that this is a non-recoverable process.
The Full Erase Hard Drive provides a DOS utility that performs the following
steps.
v Performs all the steps in Quick Erase.
v Provides a DOS utility that writes random data to all sectors of the hard
drive.
v Provide an estimate of time to completion along with a visual
representation of completion status.
v Provides messages that warn the user about non-recoverable process.
Important: Make sure that the customer backs up all data before using the
Quick or Full Erase function.
To select the Quick Erase or Full Erase Hard Drive utility, use the following
procedure.
1. Select the UTILITY option on the toolbar and press Enter.
2. Select either the QUICK ERASE or FULL ERASE HARD DISK option and
follow the instructions.
Iomega Zip drive test
Use the Iomega Zip Drive Test to test the Zip drive and the drive interface.
The test takes about 20 seconds to run.
The default tests the following:
v Controller
v Max Seek (50 times)
v Random Seek (300 sectors)
Chapter 3. Types 6058/6059/6269/6578/6579
119
Asset EEPROM backup
When replacing a system board, this utility allows the backup of all Asset
information from the EEPROM to diskette. This utility also restores data to
the EEPROM from diskette after replacement of the system board.
To run this utility, use the following procedure.
v Select Utility
v Select Asset EEPROM Backup
v Follow instructions on screen.
Viewing the test log
Errors reported by the diagnostic test will be displayed by the program as a
failed test.
To view details of a failure or to view a list of test results, use the following
procedure from any test category screen.
v Press F3 to activate the log file.
v Press F3 again to save the file to diskette or F2 to print the file.
120
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
SIMM/DIMM/RIMM memory errors
SIMM/DIMM/RIMM error messages issued by the IBM PC Enhanced
Diagnostics.
Message
Failure Found
Recommended Actions
2xx-1y
A memory error was detected in
SIMM socket Y.
Replace the SIMM in the socket
identified by the last digit of the
error code.
Re-run the test.
If the same error code occurs
again, replace the system board.
2xx-2y
A memory error was detected in
DIMM/RIMM socket Y
Replace the DIMM/RIMM in the
socket identified by the last digit
of the error code.
Re-run the test.
If the same error code occurs
again, replace the system board
or where memory is on the
processor card, replace the
processor card.
Corrupt BIOS
Information in BIOS is not as
expected.
Not able to find expected DMI
information from BIOS.
Reflash the BIOS.
Perform boot block recovery.
Replace the system board.
Memory controller chipset
vendor ID does not match
expected value.
Test aborted by user
User stopped test.
Restart test.
Note: Y is the SIMM/DIMM/RIMM socket number. Use the System Board
Layout section in the latest Hardware Maintenance Manual (HMM) to
reference the memory sockets.
Chapter 3. Types 6058/6059/6269/6578/6579
121
Setup Utility program
Attention: A customized setup configuration (other than default settings)
might exist on the computer you are servicing. Running the Setup
Utility program might alter those settings. Note the current
configuration settings and verify that the settings are in place
when service is complete.
The Setup Utility (configuration) program is stored in the permanent memory
of the computer. This program includes settings for the following:
v System Summary
v Product Data
v Devices and I/O Ports
v Start Options
v Date and Time
v System Security
v Advanced Setup
v Power Management
To run the Setup Utility program, use the following procedure.
1. Power-off the computer and wait for a few seconds until all in-use lights
go off.
2. Power-on the computer.
3. When the Setup Utility prompt appears on the screen during start-up,
press F1. The Setup Utility menu will appear.
4. Follow the instructions on the screen.
5. When finished, select System Summary to verify that any configuration
changes have been accepted.
122
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Hard disk drive boot error
A hard disk drive boot error (error codes 1962 and I999030X) can have the
following causes.
Cause
Action
The start-up drive is not in the boot sequence in
configuration.
Check the configuration and ensure the start-up
drive is in the boot sequence.
No operating system installed on the boot drive.
Install an operating system on the boot drive.
The boot sector on the start-up drive is corrupted.
The drive must be formatted, do the following:
1. Attempt to access and recover (back-up) the
failing hard disk drive.
2. Using the operating systems programs, format
the hard disk drive.
3. Go to “Preparing the hard disk drive for use”
on page 123.
The drive is defective.
Replace the hard disk drive.
When to use the Low-Level Format program
Notes:
1. The low-level format is not available on all diagnostic diskettes.
2. Before formatting the hard disk drive, make a back-up copy of the files on
the drive to be formatted.
Use the Low-Level Format program in the following situations:
v When installing software that requires a low-level format.
v When you get recurring messages from the test programs directing you to
run the Low-Level Format program on the hard disk.
v As a last resort before replacing a hard disk drive.
Preparing the hard disk drive for use
When the Low-Level Format program is finished, restore to the hard disk all
the files that you previously backed up.
1. Partition the remainder of the hard disk for the operating system. (The
commands vary with the operating system. Refer to the operating system
manual for instructions.)
2. Format the hard disk using the operating system. (The commands vary
with the operating system. Refer to the operating system manual for
instructions.)
3. Install the operating system.
You are now ready to restore the files.
Chapter 3. Types 6058/6059/6269/6578/6579
123
Additional service information
v
v
v
v
v
“Replacing a processor” on page 125
“Replacing a system board” on page 125
“Security features” on page 125
“Passwords” on page 126
“Vital product data” on page 127
v “Management Information Format (MIF)” on page 127
v
v
v
v
v
“Alert on LAN” on page 128
“Hard disk drive jumper settings” on page 128
“CD-ROM drive jumper settings” on page 129
“BIOS levels” on page 129
“Flash (BIOS/VPD) update procedure” on page 130
v “Flash recovery boot block jumper” on page 131
v “Power management” on page 131
v
v
v
v
“Network settings” on page 133
“Flash over LAN (update POST/BIOS over network)” on page 134
“Wake on LAN” on page 135
“System board memory” on page 135
The following additional service information supports Types
6058/6059/6269/6578/6579.
124
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Replacing a processor
Make sure the processor is fully seated in its socket and that the goal post
latches are engaged.
Important:
v Make sure the air baffle is installed to prevent processor
overheating.
v If the processor is not installed correctly, the system board and
the processor can be damaged.
Replacing a system board
Important:
Before replacing a system board, back up Asset information with
PC-Doctor by using the “Asset EEPROM backup” on page 120.
Notes:
1. The BIOS and Vital Product Data (VPD) for the computer you are
servicing must be installed on the new system board (FRU) after it is
installed in the computer. To do this, you must run the Flash Update
program using the Flash Update diskette. See “BIOS levels” on page 129,
“Vital product data” on page 127, and “Flash (BIOS/VPD) update
procedure” on page 130.
2. Always ensure the latest level of BIOS is installed on the computer. A
down level BIOS may cause false errors and unnecessary replacement of
the system board.
3. The processor is a separate FRU from the system board and is not
included with the system board FRU. If you are instructed to replace the
system board, use the following procedure.
a. Remove the processor from the old system board and install it on the
new system board.
b. Remove any of the following installed options on the old system
board, and install them on the new system board.
v Memory modules
c. Ensure that the new system board jumper settings match the old
system board jumper settings.
d. If the new system board does not correct the problem, reinstall the
options on the old system board, reinstall the old system board, then
replace the processor.
Security features
Security features in this section include the following:
v Passwords
Chapter 3. Types 6058/6059/6269/6578/6579
125
v Vital Product Data
v Management Information Format (MIF)
v Alert on LAN
Passwords
The following section provides information about computer hardware and
software-related passwords.
v Power-on Password
v Administrator Password
v Operating System Password
Power-on and Administrator passwords are set in the Setup Utility program.
See “Setup Utility program” on page 122 for information about running the
Setup Utility.
Power-on password: A power-on password denies access to the computer by
an unauthorized user when the computer is powered on. When a power-on
password is active, the password prompt appears on the screen each time the
computer is powered on. The computer starts after the proper password is
entered.
Removing a power-on password: To service a computer with an active and
unknown power-on password, power-off the computer and use the following
procedure.
Note: On some models, this procedure will also remove the administrator
password.
1. Unplug the power cord and remove the top cover.
2. Refer to “A20 system board layout (Type 6269)” on page 146 or
“A40/A40P system board layout
(Types 6058/6059/6578/6579)” on page 148 to find the recovery jumper.
3. Move the recovery jumper from normal to clear.
4. Power-on the computer. The system senses the change in the position and
erases the password. It is necessary to move the jumper back to the previous
position.
5. Remind the user to enter a new password when service is complete.
Administrator password: The administrator password is used to restrict
access to the Configuration/Setup Utility program. If the administrator
password is activated, and you do not enter the administrator password, the
configuration can be viewed but not changed.
126
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Note: Types 6058/6059/6269/6578/6579 has Enhanced Security Mode. If
Enhanced Security mode is enabled and there is no password given, the
computer will act as if Enhanced Security is disabled.
If Enhanced Security is Enabled and an administrator password is
given, the administrator password must be entered to use the
computer. If the administrator password is lost or forgotten, the system
board in the computer must be replaced in order to regain access to the
Configuration/Setup Utility program.
Administrator password control: The Administrator password is set in the
Setup Configuration. Refer to “Setup Utility program” on page 122.
Operating system password: An operating system password is very similar
to a power-on password and denies access to the computer by an
unauthorized user when the password is activated. The computer is unusable
until the password is entered and recognized by the computer.
Vital product data
Each computer has a unique Vital Product Data (VPD) code stored in the
nonvolatile memory on the system board. After you replace the system board,
the VPD must be updated. To update the VPD, see “Flash (BIOS/VPD)
update procedure” on page 130.
Management Information Format (MIF)
Management Information Format (MIF) is a file used to maintain a list of the
system unit serial number along with all serialized components (for example,
system board, riser card, memory, and processor).
At the time of computer manufacture, the EPROM will be loaded with the
serial numbers of the system and all major components. The customer will
have access to the MIF file via the DMI MIF Browser that is installed with the
preload and is also available on the SSCD that is provided with the system.
A company called Retain-a-Group is a central data warehouse offering serial
number data management. Retain-a-Group acts as a focal point to law
enforcement. The customer has the option to purchase serial number
information and services from Retain-a-Group. It is the customer’s
responsibility to maintain the MIF file and to inform Retain-a-Group of any
changes to the file.
Some customers may request their servicers to assist them in maintaining the
MIF file when serialized components are replaced during hardware service.
This assistance is between the customer and the servicer. The servicer can use
the DMI MIF Browser to update the MIF information in the EPROM. It is
anticipated that some servicers might charge for this service.
Chapter 3. Types 6058/6059/6269/6578/6579
127
To update the EPROM using the DMI MIF Browser, use the following
procedure.
1. Click Start from the desktop, then Programs.
2. Select IBM SystemView Agent
3. Select the Serial Number Information icon
4. Click the plus sign to expand.
5. Select the component you want to view or edit.
6. Double click on the component you want to change.
7. Enter new data in the Value field, then click Apply.
Alert on LAN
Alert on LAN provides notification of changes in the computer, even when
the computer power is turned off. Working with DMI and Wake on LAN
technologies, Alert on LAN helps to manage and monitor the hardware and
software features of the computer. Alert on LAN generates notifications to the
server of these occurrences:
v Computer disconnected from the network
v Computer unplugged from the power outlet
v All POST errors
v Operating system or POST hang condition
Alert on LAN events are configured to be Enabled or Disabled from the LAN
server only, and not from the computer. See the LAN administrator for
configuration status information.
Hard disk drive jumper settings
IDE hard disk drives for the NetVista series computers use jumpers to set the
drives as primary (master) or secondary (slave).
Note: For drives not shown below, refer to the label on the hard disk drive
for the hard disk drive settings.
1Primary (Master) Hard Disk Drive
2Secondary (Slave) Hard Disk Drive
128
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
CD-ROM drive jumper settings
CD-ROM and PC/CD-ROM drives use jumpers or tabs to set the drives as
primary (master) or secondary (slave). Refer to the drive connector labels or
the figures below for the drive settings.
AUDIO
IDE INTERFACE
39
40
RGGL
DC INPUT
1
2
5V G G 12V
See Jumper
Settings Below
CD-ROM
Primary (Master)
Secondary (Slave)
40X
: : : :
48X
: : : :
BIOS levels
An incorrect level of BIOS can cause false error and unnecessary FRU
replacement. Use the following information to determine the current level of
Chapter 3. Types 6058/6059/6269/6578/6579
129
BIOS installed in the computer, the latest BIOS available for the computer, and
where to obtain the latest level of BIOS.
v Current Level BIOS information
– Run the Configuration Utility to determine the level of BIOS installed.
v Sources for determining the latest level BIOS available
1.
IBM PC Company Home Page
http://www.ibm.com/pc/us/
2. PC PartnerInfo-Technical Database (CTSTIPS.NSF)
3. HelpCenter
4. Levels 1 and 2 Support
5. RETAIN
v Sources for obtaining the latest level BIOS available
1.
IBM PC Company Home Page
http://www.ibm.com/pc/us/
2. PC PartnerInfo-Technical Database (CTSTIPS.NSF)
3. HelpCenter
4. Levels 1 and 2 Support
To update (flash) the BIOS, see “Flash (BIOS/VPD) update procedure”.
Flash (BIOS/VPD) update procedure
Attention: Refer to the information label located inside the system unit cover
for any model-specific information.
1. Power-off the computer.
2. Insert the flash update diskette into drive A.
3. Power-on the computer.
4. When the Update Utility appears; select the country/keyboard, then press
Enter.
5. If the computer serial number was previously recorded, the number is
displayed with an option to update it. Press Y to update the serial number.
6. Type the 7-digit serial number of the computer you are servicing, then
press Enter.
7. Follow the instructions on the screen to complete the flash (BIOS/VPD)
update procedure.
130
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Flash recovery boot block jumper
Attention: If an interruption occurs during a Flash/BIOS upgrade, the BIOS
might be left in an unusable state. The Boot Block jumper enables
you to restart the system and recover the BIOS.
To perform a Flash/BIOS recovery using the recovery jumper, use the
following procedure.
1. Power-off the computer and remove the cover.
2. Move the system board recovery jumper to the clear position. Refer to
“A20 system board layout (Type 6269)” on page 146, “A40/A40P system
board layout
(Types 6058/6059/6578/6579)” on page 148, or to the label inside the
computer for more information.
3. Insert the upgrade diskette into the diskette drive.
4. Power-on the computer. The IBM Logo will appear.
5. When the Flash Update Utility appears, select the country/keyboard, then
press Enter.
6. If the computer serial number was previously recorded, the number is
displayed with an option to update it. Press Y to update the serial number.
7. Type the 7-digit serial number of the computer you are servicing, then
press Enter.
8. Follow the instructions on the screen to complete the flash (BIOS/VPD)
update procedure.
9. When you are instructed to reboot the computer, power-off the computer
and move the recovery jumper to the normal position. Then replace the
cover and power-on the computer.
Power management
Power management reduces the power consumption of certain components of
the computer such as the system power supply, processor, hard disk drives,
and some monitors. Advanced Power Management and Rapid Resume
Manager are features of some personal computers.
Automatic configuration and power interface (ACPI) BIOS
Being an ACPI BIOS system, the operating system is allowed to control the
power management features of the computer and the setting for Advanced
Power Management (APM) BIOS mode are ignored. Not all operating systems
support ACPI BIOS mode.
Advanced Power Management
Energy-saving settings can be viewed and changed by using the Advanced
Power Management menu in the Configuration/Setup Utility program.
Chapter 3. Types 6058/6059/6269/6578/6579
131
Attention: If a device, such as a monitor, does not have power-management
capabilities, it can be damaged when exposed to a reduced-power
state. Before making energy-saving selections for the monitor,
check the documentation supplied with the monitor to see if it
supports Display Power Management Signaling (DPMS).
Automatic Hardware Power Management features
Automatic Hardware Power Management can reduce the power states of the
computer, processor, and monitor (if the monitor supports DPMS) if they are
inactive for a predetermined length of time.
There are three levels of specified time that the computer must be inactive
before the power management options that are selected take effect. Select the
amount of time that is offered within each level.
Set time from 5 minutes to 4 hours.
Set time from 10 minutes to 5 hours.
Set time from 15 minutes to 6 hours.
Level 1
Level 2
Level 3
At each level, you can define the amount of energy savings by specifying
values for the following options.
v
System Power
– Select On for the computer to remain on.
– Select Off for the computer to shut down.
v
Processor Speed
Set the microprocessor to be disabled, or to run at 1, 10, 25, or 50 percent of
its internal clock speed.
v
Display
Set display to be disabled or to be reduced at these power states:
– Standby: Screen is blank, but can be restored immediately when any
activity is detected.
– Suspend: Monitor uses less power than in Standby mode. Screen image
is restored after a few seconds when any activity is detected.
– Off: Monitor power is off. Press Monitor power button to restore power.
On some monitors, you might have to depress the power button twice.
Setting Automatic Hardware Power Management features
1. Start the Configuration/Setup Utility program (see “Setup Utility
program” on page 122).
132
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
2. Select Advanced Power Management from the Configuration/Setup
Utility program menu.
3. Select the APM BIOS Mode and be sure it is set to Enabled. If it is not,
press Left Arrow (}) or Right Arrow (Æ) to change the setting.
4. Select Automatic Hardware Power Management.
5. Set Automatic Hardware Power Management to Enabled.
6. Select values for the three categories of power management (system
power, processor speed, and display), as necessary.
7. Set Hard Disk to Enabled or Disabled.
Note: This does not apply to SCSI drives.
8. Press Esc twice to return to the Configuration/Setup Utility program
menu.
9. Before you exit from the program, select Save Settings from the
Configuration/Setup Utility program menu.
10. To exit from the Configuration/Setup Utility program, press Esc and
follow the instructions on the screen.
Automatic Power-On features
The Automatic Power-On features within the Power Management menu allow
you to enable and disable features that turn on the computer automatically.
v Serial Port A Ring Detect: With this feature set to Enabled and an external
modem connected to serial port (COM1), the computer will turn on
automatically when a ring is detected on the modem.
v PCI Modem Ring Detect: With this feature set to Enabled , the computer
will turn on automatically when a ring is detected on the internal modem.
v PCI Wake Up: This feature allow PCI cards that support this capability to
wake the system.
v Wake Up on Alarm: You can specify a date and time at which the
computer will be turned on automatically. This can be either a single event
or a daily event.
v Wake on LAN: If the computer has a properly configured token-ring or
Ethernet LAN adapter card that is Wake on LAN-enabled and there is
remote network management software, you can use the IBM-developed
Wake on LAN feature. When you set Wake on LAN to Enabled, the
computer will turn on when it receives a specific signal from another
computer on the local area network (LAN). For further information, see
“Wake on LAN” on page 135.
Network settings
This section applies only to computers that are linked to a network.
Chapter 3. Types 6058/6059/6269/6578/6579
133
The Configuration/Setup Utility program includes settings that can be
enabled and disabled to configure the network interface in the computer.
These settings are the following:
v Flash over LAN (Update POST/BIOS over Network)
v Wake on LAN
Flash over LAN (update POST/BIOS over network)
Note: For local Flash (BIOS/VPD) update, see “Flash (BIOS/VPD) update
procedure” on page 130.
This setting is used to enable or disable the Flash over LAN feature. When the
feature is enabled, the system programs, in the computer, can be updated
remotely from a network server. If the administrator password is set in the
computer, it does not have to be entered by the server.
To access the Flash over LAN setting, use the following procedure.
1. Start the Configuration/Setup Utility program. See “Setup Utility
program” on page 122.
2. Select System Security.
3. Select POST/BIOS Update from the Configuration/Setup Utility program
menu.
4. To enable Flash over LAN, select Enabled. To disable Flash over LAN,
select Disabled.
5. Press Esc twice to return to the Configuration/Setup Utility program
menu.
6. Before you exit from the program, select Save Settings from the
Configuration/Setup Utility program menu.
7. To exit from the Configuration/Setup Utility program, press Esc and
follow the instructions on the screen.
134
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Wake on LAN
This setting is used to enable or disable the IBM-developed Wake on LAN
feature. This feature makes it possible for the computer to be turned on
remotely by a network server. Remote network management software must be
used in conjunction with this feature.
To access the Wake on LAN setting, use the following procedure.
1. Start the Configuration/Setup Utility program. See “Setup Utility
program” on page 122.
2. Select Advanced Power Management.
3. Select Automatic Power On from the program menu.
4. Select Wake on LAN from the Automatic Power On menu.
5. To enable Wake on LAN, select Enabled. To disable Wake on LAN, select
Disabled.
6. Press Esc until you return to the Configuration/Setup Utility program
menu.
7. Before you exit from the program, select Save Settings from the
Configuration/Setup Utility program menu.
8. To exit from the Configuration/Setup Utility program, press Esc and
follow the instructions on the screen.
System board memory
The following matrix cross-references the name of the computer (printed on
the logo) and the size, speed, and type of memory modules supported in the
computer.
Computers
Memory Module
Types62696058/6059/6578/6579
Size
Speed
Type
64 MB128 MB256
MB
133 MHz
SDRAMNonParityIndustry
Standard
Supported memory configuration
DIMM sizes of 64 MB, 128 MB and 256 MB are acceptable. Start filling DIMM
socket 0, then 1. Use 3.3 V unbuffered 133 MHz SDRAM non-parity DIMMs
only.
Chapter 3. Types 6058/6059/6269/6578/6579
135
Computer exploded view Types 6058/6059/6269/6578/6579
136
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Input/Output connectors - Type 6269
2
1
1
1Power cord
2Mouse connector
3USB connector 2
4USB connector 1
5Serial connector 2
6Parallel connector
7Joystick / MIDI
8Microphone connector
9Audio input connector
10Audio output connector
11Monitor connector
12 Serial connector 1
13 Keyboard connector
Chapter 3. Types 6058/6059/6269/6578/6579
137
Input/Output connectors - Types 6058/6059/6578/6579
2
1
1Power connector
2Mouse
3USB connector 2
4Parallel connector
5Serial connector 2 (joystick/MIDI connector in
some models)
6Audio out connector
138
6649
7Audio in connector
8Microphone connector
9Monitor connector
10Serial connector 1
11USB connector 1
12Keyboard connector
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Cover removal
Note
The front panel is integrated with the top cover.
Firmly press the cover latch buttons on both sides. Pull up the back end of
cover, and swing the cover toward the front of the computer.
Replacing the cover
Pivot the cover from the front, and move it down over the computer until the
cover snaps into place.
Chapter 3. Types 6058/6059/6269/6578/6579
139
EMC shield (front)
Models that are not shipped with a CD-ROM drive have an EMC shield
covering the drive bay. To remove the EMC shield, remove the front cover.
Then, remove the single screw that holds the EMC shield in place.
EMC shield (system board)
Remove the eight screws that hold the EMC shield in place.
Installing adapters
This section provides information and instructions for installing and removing
adapters.
Adapter slots
Types 6058/6059/6269/6578/6579 have four expansion slots used to connect
adapters to the peripheral component interconnect (PCI) bus.
To install an adapter in a PCI or AGP expansion slot:
1. Remove the adapter from its static-protective package.
2. Remove the metal I/O bracket form the adapter slot.
140
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
3. Install the adapter into the appropriate slot on the system board.
4. Install the adapter slot cover latch. Pivot the latch back to horizontal
Note: If you are installing a Wake on LAN supported network adapter,
attach the Wake on LAN cable that came with the adapter to the
Wake on LAN connector on the system board. If you also want to
take advantage of the Alert on LAN feature of the computer, you
must install the network adapter in PCI slot 1.
Air duct (Types 6058/6059/6278/6279)
1. The air duct in some machines may have a hole in the side. Press the
metal latch that is behind the hole, and swing out the duct to a 45-degree
angle and lift it up.
Chapter 3. Types 6058/6059/6269/6578/6579
141
2. If the air duct does not have a hole, simply swing out the duct to a
45-degree angle and lift it up.
CD-ROM drive removal
1. Swing the 5.25″ drive cage up and out.
2. Remove the two screws that hold the CD-ROM drive in place. Lift the
CD-ROM drive out of the cage.
3. When replacing the drive cage into its horizontal position, be sure place
the cage latch back to its regular horizontal position. This is necessary so
that the machine cover will fit properly.
Fan/speaker bracket removal
1. Detach the left side of the fan/speaker bracket by pushing the two left
tabs that latch the bracket to the chassis.
142
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
2. Locate the right tab that hinges the fan/speaker bracket to the chassis.
Push the tab to detach the bracket from the chassis.
3. Swing the 3.5″ drive cage up and latch into vertical.
4. Lift the fan/speaker bracket back and out.
Hard drive removal
1. Swing the 3.5″ drive cage up, and latch it to the vertical position.
Chapter 3. Types 6058/6059/6269/6578/6579
143
2. Press the two side rail tabs and push the HD from the bottom. Pull the
HD out.
3. When replacing the drive cage into its horizontal position, be sure place
the cage latch back to its regular horizontal position. This is necessary so
that the machine cover will fit properly.
Power supply removal
1. Remove the four screws that hold the power supply to the back of the
chassis.
2. The power supply is attached to the base of the chassis by a latch on the
front. Slide the power supply forward to dislatch if from the chassis.
144
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
3. Lift out the power supply.
Chapter 3. Types 6058/6059/6269/6578/6579
145
A20 system board layout (Type 6269)
System board locations
1
2
3
4
5
6
7
8
9
CPU fan connector
Microprocessor
Power connector
DIMM 1
DIMM 2
Diskette connector
Secondary IDE connector
Primary IDE connector
Battery
10
11
12
13
14
15
16
17
Clear CMOS/recovery jumper
Front fan connector
Wake on LAN connector
PCI connector 3
PCI connector 2
PCI connector 1
CD-ROM audio connector
Serial 2 connector
A20 System board jumper settings
The following table contains the jumper setting information. (D) indicates the
default setting.
A20 Clear CMOS/Flash Boot Block Recovery
Use the recovery jumper setting to Clear CMOS or to Flash Boot Block
Recover.
146
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Jumper
Setting
Description
CMOS Reset
2-3
CMOS Reset/Flash Recovery Mode
1-2 (D)
Normal Mode
Note: The A20 CMOS clear/recovery jumper pins are numbered as follows:
v Pin 1 is the nearest to the battery.
v Pins 2 and 3 are below pin 1, as seen in the A20 System Board
layout.
A20 Processor Speed Settings
Processor speed for Type 6269 computers is fixed and are determined by the
processor. There are no settings required.
A20 Diskette Write Access
Diskette Write Enable and Write Protect options are changed in the Setup
Configuration. See “Setup Utility program” on page 122.
Chapter 3. Types 6058/6059/6269/6578/6579
147
A40/A40P system board layout
(Types 6058/6059/6578/6579)
32
31
System board locations
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
#2 fan connector
Microprocessor
DIMM 0
DIMM 1
Power LED connector
RFID connector
Front USB connector
Secondary IDE connector
Diskette connector
Primary IDE connector
Power connector
CMOS clear/recovery jumper
#1 fan connector
Battery
SCSI adapter LED connector
Alert on LAN
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Wake on LAN
PCI slot 3
PCI slot 2
PCI slot 1
AGP connector
CD-ROM audio
Speaker connector
Audio output
Audio input
Serial port 2
Microphone input
Monitor port
Parallel port
Serial port 1
USB connectors
Mouse and keyboard connectors
A40/A40P System board jumper settings
The following table contains the jumper setting information. (D) indicates the
default setting.
148
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
A40/A40P Clear CMOS/Flash Boot Block Recovery
Use the recovery jumper setting to Clear CMOS or to Flash Boot Block
Recover.
Jumper
Setting
Description
CMOS Reset
2-3
CMOS Reset/Flash Recovery Mode
1-2 (D)
Normal Mode
Note: The A40/A40P CMOS clear/recovery jumper pins are numbered as
follows:
v Pin 1 is the farthest from the battery.
v Pins 2 and 3 are below pin 1, as seen in the A40/A40P System Board
layout.
A40/A40P Processor Speed Settings
Processor speed for NetVista type 6058/6059/6578/6579 computers is fixed
and is determined by the processor. There are no settings required.
A40/A40P Diskette Write Access
Diskette Write Enable and Write Protect options are changed in the Setup
Configuration. See “Setup Utility program” on page 122.
Chapter 3. Types 6058/6059/6269/6578/6579
149
Symptom-to-FRU index
The Symptom-to-FRU index lists error symptoms and possible causes. The
most likely cause is listed first. Always begin with “General checkout” on
page 104. See “Chapter 1. IBM PC Enhanced Diagnostics error codes” on
page 1 when running diagnostics. This index can also be used to help you
decide which FRUs to have available when servicing a computer. If you are
unable to correct the problem using this index, go to “Undetermined
problems” on page 171.
Notes:
1. If you have both an error message and an incorrect audio response,
diagnose the error message first.
2. If you cannot run the diagnostic tests or you get a diagnostic error code
when running a test, but did receive a POST error message, diagnose the
POST error message first.
3. If you did not receive any error message, look for a description of your
error symptoms in the first part of this index.
4. Check all power supply voltages before you replace the system board. (See
“Power supply” on page 108.)
5. Check the hard disk drive jumper settings before you replace a hard disk
drive. (See “Hard disk drive jumper settings” on page 128.)
Important:
1.
Some errors are indicated with a series of beep codes (see
“Beep symptoms”).
Types 6058/6059/6269/6578/6579 computers default to come
up quiet (no beep and no memory count and checkpoint code
display) when no errors are detected by POST. To enable beep
and memory count and checkpoint code display when a
successful POST occurs, do the following:
a. Select Start Options in the Configuration/Setup Utility
program (see“Setup Utility program” on page 122).
b. Set Power-On Self-Test to Enhanced.
2. The processor is a separate FRU from the system board; the
processor is not included with the system board FRU.
Beep symptoms
Beep symptoms are short tones or a series of short tones separated by pauses
(intervals without sound). See the following examples.
150
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Beeps
Description
1-2-X
v One beep
v A pause (or break)
v Two beeps
v A pause (or break)
v Any number of breaks
Four continuous beeps
4
Use the following table to diagnose beep symptoms.
Beep Symptom
FRU/Action
1-1-3CMOS read-write error
1. Run Setup
2. System Board
1-1-4ROM BIOS check error
1. System Board
1-2-XDMA error
1. System Board
1-3-X
1. Memory Module
2. System Board
1-4-4
1. Keyboard
2. System Board
1-4-XError detected in first 64 KB of RAM
1. Memory Module
2. System Board
2-1-1, 2-1-2
1. Run Setup
2. System Board
2-1-XFirst 64 KB of RAM failed
1. Memory Module
2. System Board
2-2-2
1. Video Adapter (if installed)
2. System Board
2-2-XFirst 64 KB of RAM failed
1. Memory Module
2. System Board
2-3-X
1. Memory Module
2. System Board
2-4-X
1. Run Setup
2. Memory Module
3. System Board
Chapter 3. Types 6058/6059/6269/6578/6579
151
Beep Symptom
FRU/Action
3-1-XDMA register failed
1. System Board
3-2-4Keyboard controller failed
1. System Board
2. Keyboard
3-3-4Screen initialization failed
1. Video Adapter (if installed)
2. System Board
Display
3-4-1Screen retrace test detected an error
1. Video Adapter (if installed)
2. System Board
3. Display
3-4-2POST is searching for video ROM
1. Video Adapter (if installed)
2. System Board
4
1. Video Adapter (if installed)
2. System Board
All other beep code sequences
1. System Board
One long and one short beep during POST.Base
640 KB memory error or shadow RAM error
1. Memory Module
One long beep and two or three short beeps
during POST.(Video error)
1. Video Adapter (if installed)
Three short beeps during POST
1. See “System board memory” on page 135
2. System Board
2. System Board
2. System Board
Continuous beep
1. System Board
Repeating short beeps
1. Keyboard stuck key?
2. Keyboard Cable
3. System Board
No-beep symptoms
Note: Types 6058/6059/6269/6578/6579 computers default to come up quiet
(no beep and no memory count and checkpoint code display) when no
errors are detected by POST.
To enable beep and memory count and checkpoint code display when a
successful POST occurs, do the following:
1. Select Start Options in the Configuration/Setup Utility program
(see “Setup Utility program” on page 122).
152
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
2. Set Power-On Self Test to Enhanced.
Symptom/Error
FRU/Action
No beep during POST but computer works
correctly.
1. System Board
No beep during POST.
1. See “Undetermined problems” on page 171
2. System Board
3. Memory Module
4. Any Adapter or Device
5. Power Cord
6. Power Supply
POST error codes
In the following index, X can represent any number.
POST Error Code
FRU/Action
000SCSI Adapter not enabled
1. Verify adapter device and Bus Master fields
are enabled in PCI configuration program.
See documentation shipped with computer.
02X
1. SCSI Adapter
08XCheck SCSI terminator installation.
1. SCSI Cable
2. SCSI Terminator
3. SCSI Device
4. SCSI Adapter
101System board interrupt failure
1. System Board
102System board timer error
1. System Board
106
1. System Board
110System board memory parity error
1. Memory Module
2. System Board
111I/O channel parity error
1. Reseat adapters
2. Any adapter
3. System Board
114Adapter ROM error
1. Adapter Memory
2. System Board
129Internal cache test error
1. Processor
2. L2 Cache Memory
3. System Board
Chapter 3. Types 6058/6059/6269/6578/6579
153
POST Error Code
FRU/Action
151Real-time clock failure
1. System Board
161Bad CMOS battery
1. Run Setup
2. CMOS Backup Battery (see “Safety
information” on page 185)
3. System Board
162Configuration mismatch
1. Run Setup and verify Configuration
2. Had a device been added, removed, changed
location? If not, suspect that device.
3. Power-on external devices first, then power-on
computer
4. CMOS Backup Battery (see “Safety
information” on page 185)
System Board
5. System Board
162And unable to run diagnostics
1. Diskette Drive
2. System Board
3. Diskette Drive Cable
163Clock not updating or invalid time set
1. Time and Date Set?
2. CMOS Backup Battery (see “Safety
information” on page 185)
3. System Board
164POST detected a base memory or extended
memory size mismatch error or RIMM socket 3 is
populated with a RIMM memory module
1. Run Setup. Check System Summary menu for
memory size change. (See“Setup Utility
program” on page 122.)
2. Run the Extended Memory Diagnostic tests
166Boot Block Check Sum Error
1. Run Flash Recovery using Boot Block. See
“Flash recovery boot block jumper” on page
131.
2. System Board
167Microprocessor installed that is not supported
by the current POST/BIOS
1. Run Setup. Check Stepping level for the
BIOS level needed, then perform the flash
update.
2. Processor
168Alert on LAN error
1. Run Setup. Check to see that Ethernet and
Alert on LAN are enabled.
2. System Board
17X, 18X
154
6649
1. C2 Security
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
175
1. Run Configuration. See “Setup Utility
program” on page 122.
2. System Board
176
1. Covers were removed from the computer
177Corrupted Administrator Password
1. System Board
178
1. System Board
183
1. Enter the administrator password
184No RFID Antenna
1. Make sure Asset Care and Asset ID are
enabled in Configuration/Setup
2. RFID Antenna
3. System Board
185Corrupted boot sequence
1. Set configuration and reinstall the boot
sequence
186
1. System Board
187
1. Clear Administration password
2. System Board
189
1. More than three password attempts were
made to access the computer
190Chassis intrusion detector was cleared. This is
information only, no action required. If this code
does not clear:
1. System Board
1XXNot listed above
1. System Board
201, 20XMemory data error
1. Run Enhanced Diagnostics Memory Test
2. Memory Module
3. System Board
225
1. Unsupported Memory
229External cache test error
1. L2 Cache Memory
2. System Board
262POST detected a base memory or extended
memory type error
1. Run Setup. Check System Summary menu for
memory. (See “Setup Utility program” on
page 122.)
2. Run the Extended Memory Diagnostic tests.
Chapter 3. Types 6058/6059/6269/6578/6579
155
POST Error Code
FRU/Action
301
1. Keyboard
2. Keyboard Cable
3. System Board
303With an 8603 error
1. Mouse
2. Keyboard
3. Keyboard Cable
4. System Board
303With no 8603 error
1. Keyboard
2. Keyboard Cable
3. System Board
3XXNot listed above
1. Keyboard
2. Keyboard Cable
3. System Board
5XX
1. Video Adapter (if installed)
2. System Board
601
1. Diskette Drive A
2. Diskette Drive Cable
3. System Board
602
1. Bad Diskette?
2. Verify Diskette and retry
604And able to run diagnostics
1. Run Setup and verify diskette configuration
settings
2. Diskette Drive A/B
3. Diskette Drive Cable
4. System Board
605POST cannot unlock the diskette drive
1. Diskette Drive
2. Diskette Drive Cable
3. System Board
662
156
6649
1. Diskette drive configuration error or wrong
diskette drive type; run Setup Configuration
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
6XXNot listed above
1. Diskette Drive
2. System Board
3. External Drive Adapter
4. Diskette Drive Cable
5. Power Supply
762Math coprocessor configuration error
1. Run Setup
2. Processor
3. System Board
7XX Not listed above
1. Processor
2. System Board
962 Parallel port configuration error
1. Run Configuration
2. Parallel Adapter (if installed)
3. System Board
9XX
1. Printer
2. System Board
1047
1. 16-Bit AT Fast SCSI Adapter
107XCheck SCSI terminator installation
1. Check SCSI terminator installation
2. SCSI Cable
3. SCSI Terminator
4. SCSI Device
5. SCSI Adapter
1101Serial connector error, possible system board
failure
1. Run Enhanced Diagnostics
1101, 1102, 1106, 1108, 1109
1. System Board
2. Any Serial Device
1107
1. Communications Cable
2. System Board
1102Card selected feedback error
1. Run Enhanced Diagnostics
1103Port fails register check
1. Run Enhanced Diagnostics
2. System Board
1106Serial option cannot be turned off
1. Run Enhanced Diagnostics
2. System Board
Chapter 3. Types 6058/6059/6269/6578/6579
157
POST Error Code
FRU/Action
1107
1. Serial Device Cable
2. System Board
1110Register test failed
1. Run Enhanced Diagnostics
2. System Board
1116Interrupt error
1. Run Enhanced Diagnostics
1117Failed baud rate test
1. Run Enhanced Diagnostics
1162 Serial port configuration error
1. Run Configuration
2. Serial Adapter
(if installed)
3. System Board
11XXNot listed above
1. System Board
1201
1. System Board
2. Any Serial Device
1202, 1206, 1208, 1209, 12XX
1. Dual Async Adapter/A
2. System Board
3. Any Serial Device
1207
1. Communications Cable
2. Dual Async Adapter/A
13XX
1. Game Adapter
1402Printer not ready
Information only
1403No paper error, or interrupt failure
Information only
1404System board timeout failure
1. Run Enhanced Diagnostics
1405Parallel adapter error
1. Run Enhanced Diagnostics
1406Presence test error
1. Run Enhanced Diagnostics
14XXNot listed above. Check printer before
replacing system board
1. Printer
15XX
1. SDLC Adapter
1692Boot sequence error
1. Run FDISK to ensure at least one active
partition is set active
16XX
1. 36/38 Workstation Adapter
1762Hard disk drive configuration error
1. Run Configuration. (See “Setup Utility
program” on page 122.)
158
6649
2. System Board
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
1780 (Disk Drive 0)1781 (Disk Drive 1)1782 (Disk
Drive 2)1783 (Disk Drive 3)
1. See “Power supply” on page 108
2. Hard Disk Drive
3. System Board
4. Hard Disk Cable
5. Power Supply
180X, 188XPCI configuration or resource error
1. Run Setup and verify PCI/ISA configuration
settings.
2. If necessary, set ISA adapters to Not available to
allow PCI adapters to properly configure.
3. Remove any suspect ISA adapters.
4. Rerun diagnostics.
5. PCI Adapter
1962Boot sequence error
1. Possible hard disk drive problem; see “Hard
disk drive boot error” on page 123.
209X
1. Diskette Drive
2. Diskette Cable
20XXNot listed above
1. BSC Adapter
21XX
1. SCSI Device
2. 16-bit AT Fast SCSU adapter
3. Alternate BSC adapter
2401, 2402If screen colors change
1. Display
2401, 2402If screen colors are OK
1. System Board
2. Display
2409
1. Display
2410
1. System Board
2. Display
2462Video memory configuration error
1. Check cable connections
2. Run Setup and verify video configuration
settings
3. Video Memory Modules
4. Video Adapter (if installed)
5. System Board
4611, 4630
1. Multiport/2 Interface Board
2. Multiport/2 Adapter
Chapter 3. Types 6058/6059/6269/6578/6579
159
POST Error Code
FRU/Action
4612, 4613, 4640, 4641
1. Memory Module Package
2. Multiport/2 Adapter
4650
1. Multiport/2 Interface Cable
46XXNot listed above
1. Multiport/2 Adapter
2. Multiport/2 Interface
Board
3. Memory Module
5600
1. Financial System Controller Adapter
5962An IDE device (other than hard drive)
configuration error
1. Run Configuration
2. CD-ROM Drive
3. CD-ROM Adapter
4. Zip or other ATAPI device
5. System Board
62XX
1. 1st Store Loop Adapter
2. Adapter Cable
63XX
1. 2nd Store Loop Adapter
2. Adapter Cable
64XX
1. Network Adapter
71XX
1. Voice Adapter
74XX
1. Video Adapter
(if installed)
76XX
1. Page Printer Adapter
78XX
1. High Speed Adapter
79XX
1. 3117 Adapter
80XX
1. PCMCIA Adapter
84XX
1. Speech Adapter
2. Speech Control Assy.
8601, 8602
1. Pointing Device (Mouse)
2. System Board
8603, 8604
1. System Board
2. Pointing Device
(Mouse)
160
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
86XXNot listed above
1. Mouse
2. System Board
89XX
1. PC Music Adapter
2. MIDI Adapter Unit
91XX
1. Optical Drive
2. Adapter
96XX
1. SCSI Adapter
2. Any SCSI Device
3. System Board
10101, 10102, 10104, 10105, 10106, 10107, 10108,
10109, 10111,
10112, 10113, 10114,
10115, 10116
1. Have customer verify correct operating system
device drivers are installed and operational.
10103, 10110, 101171
1. System Board
2. Modem
2. Data/Fax Modem
10117Not listed above
1. Check system speaker
2. Check PSTN cable
3. External DAA
(if installed)
4. Modem
10118
1. Run Diagnostics and verify the correct
operation of the modem slot
2. Modem
10119
1. Diagnostics detected a non-IBM modem
2. Modem
10120
1. Check PSTN Cable
2. External DAA
(if installed)
3. Modem
10132,
10135,
10138,
10141,
10144,
10147,
10150,
10133,
10136,
10139,
10142,
10145,
10148,
10151,
10134,
10137,
10140,
10143,
10146,
10149,
10152
1. Modem
Chapter 3. Types 6058/6059/6269/6578/6579
161
POST Error Code
FRU/Action
10153
1. Data/Fax Modem
2. System Board
101XXNot listed above
1. Modem Adapter/A
2. Data/Fax Modem
3. System Board
10450, 10451, 10490,
10491, 10492, 10499Read/write error
1. Run Enhanced Diagnostics
2. Hard Disk Drive
3. System Board
10452Seek test error
1. Run Enhanced Diagnostics
10453Wrong drive type?
Information only
10454Sector buffer test error
1. Run Enhanced Diagnostics
10455, 10456Controller error
1. Run Enhanced Diagnostics
10459Drive diagnostic command error
Information only
10461Drive format error
1. Run Enhanced Diagnostics
10462Controller seek error
1. Run Enhanced Diagnostics
10464Hard Drive read error
1. Run Enhanced Diagnostics
10467Drive non-fatal seek error
1. Run Enhanced Diagnostics
10468Drive fatal seek error
1. Run Enhanced Diagnostics
10469Drive soft error count exceeded
1. Run Enhanced Diagnostics
10470, 10471, 10472Controller wrap error
1. Run Enhanced Diagnostics
10473Corrupt data. Low level format might be
required
Information only
10480
1. Hard Disk Drive (ESDI)
2. Drive Cable
3. System Board
10481ESDI drive D seek error
1. Run Enhanced Diagnostics
10482Drive select acknowledgement bad
1. Run Enhanced Diagnostics
106X1
1. Check Configuration
2. Ethernet Adapter
162
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
10635
1. Power-off computer, wait ten seconds then
power-on the computer
2. Ethernet Adapter
10651, 10660
1. Check Cables
2. Ethernet Adapter
106XXNot listed above
1. Ethernet Adapter
107XX
1. 5.25-inch External
Diskette Drive
2. 5.25-inch Diskette
Drive Adapter/A
109XXCheck the adapter cables
1. ActionMedia
Adapter/A
2. System Board
112XXThis adapter does not have cache
1. SCSI Adapter
2. Any SCSI Device
3. System Board
119XX
1. 3119 Adapter
121XX
1. Modem Adapter
2. Any Serial Device
3. System Board
136XX
1. ISDN Primary Rate Adapter
2. System Board
137XX
1. System Board
141XX
1. Realtime Interface Coprocessor Portmaster
Adapter/A
143XX
1. Japanese Display Adapter
2. System Board
14710, 14711
1. System Board Video Adapter
2. Adapter Video Memory
148XX
1. Video Adapter
14901, 14902,
1491X, 14922
1. Video Adapter
(if installed)
2. System Board
3. Display (any type)
Chapter 3. Types 6058/6059/6269/6578/6579
163
POST Error Code
FRU/Action
14932
1. External Display
2. Video Adapter
161XX
1. FaxConcentrator Adapter
164XX
1. 120 MB Internal Tape Drive
2. Diskette Cable
3. System Board
16500
1. 6157 Tape Attachment
2. Adapter
16520, 16540
1. 6157 Streaming Tape Drive
2. 6157 Tape Attachment Adapter
166XX, 167XX
1. Token Ring Adapter
2. System Board
18001 to 18029
1. Wizard Adapter
2. Wizard Adapter Memory
18031 to 18039
1. Wizard Adapter Cable
185XXXX
1. DBCS Japanese Display Adapter/A
2. System Board
20001 to 20003
1. Image Adapter/A
Image-I Adapter/A
2. Memory Module DRAM, VRAM
20004
1. Memory Module DRAM, VRAM
2. Image Adapter/A
Image-I Adapter/A
20005 to 20010
1. Image Adapter/A
Image-I Adapter/A
2. Memory Module DRAM, VRAM
200XXNot listed above
1. Image Adapter/A
2. Image-I Adapter/A
3. Memory Module DRAM, VRAM
4. System Board
20101 to 20103
1. Printer/Scanner Option
2. Image Adapter/A
3. Memory Module DRAM, VRAM
164
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
20104
1. Memory Module DRAM, VRAM
2. Printer/Scanner Option
3. Image Adapter/A
20105 to 20110
1. Printer/Scanner Option
2. Image Adapter/A
3. Memory Module DRAM, VRAM
Image Adapter/A Memory Test failure indicated
by graphic of adapter
1. Replace memory module (shown in graphic)
206XX
1. SCSI-2 Adapter
2. Any SCSI Device
3. System Board
208XXVerify there are no duplicate SCSI ID
settings on the same bus.
1. Any SCSI Device
210XXXXInternal bus, size
unknown210XXX1External bus, size unknown
1. SCSI Hard Disk Drive
2. SCSI Adapter or System Board
3. SCSI Cable
4. SCSI ID Switch (on some models)
Tape Drive amber LED remains on
1. Tape Drive
2. SCSI Cable (internal)
3. SCSI Adapter or System Board
Tape Drive green ″in use″ LED fails to come on
1. Tape Drive
2. SCSI Adapter or System Board
3. SCSI Cable (internal)
4. SCSI Cable (external)
Tape automatically ejected from drive
1. Tape Cassette
Drive
SCSI ID on rotary switch does not match SCSI ID
set in configuration. Verify drive switches inside
cover are set to zero
1. Rotary Switch Circuit Board
2. Circuit Board Cable
3. Tape Drive
Tape sticks or breaks in drive. Verify that the tapes 1. Tape Cassette
used meet ANSI standard X3B5
212XX
1. SCSI Printer
2. Printer Cable
213XX
1. SCSI Processor
Chapter 3. Types 6058/6059/6269/6578/6579
165
POST Error Code
FRU/Action
214XX
1. WORM Drive
215XXXC, 215XXXD, 215XXXE, 215XXXUIf an
external device, and power-on LED is off, check
external voltages
1. CD-ROM Drive I
2. CD-ROM Drive II
Enhanced CD-ROM Drive II
Any CD-ROM Drive
3. SCSI Cable
4. SCSI Adapter or System Board
216XX
1. Scanner
217XXIf an external device, and power-on LED is
off, check external voltages
1. Rewritable Optical Drive
2. SCSI Adapter or System Board
3. SCSI Cable
218XXCheck for multi CD tray or jukebox
1. Changer
219XX
1. SCSI Communications Device
24201Y0, 24210Y0Be sure wrap plug is attached
1. ISDN/2 Adapter
2. ISDN/2 Wrap Plug
3. ISDN/2 Communications Cable
273XX
1. 1 Mbps Micro Channel
2.
27501, 27503, 27506, 27507
Infrared LAN Adapter
1. ServerGuard Adapter
2. System Board
27502, 27504, 27510, 27511, 27533, 27534, 27536,
27537
1. ServerGuard Adapter
27509
1. Remove redundant adapters, run Auto
Configuration program, then retest.
27512
1. WMSELF.DGS diagnostics file is missing
2. WMSELF.DGS diagnostics file is incorrect
27535
1. 3V Lithium Backup Battery
2. ServerGuard Adapter
27554
1. Internal Temperature out of range
2. ServerGuard Adapter
27555, 27556
1. ServerGuard Adapter
2. Power Supply
166
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POST Error Code
FRU/Action
27557
1. 7.2V NiCad Main Battery Pack
2. ServerGuard Adapter
27558, 27559, 27560, 27561
1. PCMCIA Type II Modem
2. ServerGuard Adapter
27562
1. External Power Control not connected
2. External Power Control
3. ServerGuard Adapter
27563, 27564
1. External Power Control
2. ServerGuard Adapter
275XX
1. Update Diagnostic Software
27801 to 27879
1. Personal Dictation System
2.
Adapter
3. System Board
27880 to 27889
1. External FRU
(Speaker, Microphone)
999030XHard disk reset failure
1. Possible hard disk drive problem; see “Hard
disk drive boot error” on page 123.
Miscellaneous error messages
Message/Symptom
FRU/Action
CMOS Backup Battery inaccurate
1. CMOS Backup Battery (see “Safety
information” on page 185)
2. System Board
Changing colors
1. Display
Computer will not power-off. See “Power supply”
on page 108.
1. Power Switch
Computer will not RPL from server
1. Ensure that network is in startup sequence as
first device or first device after diskette
2. System Board
2. Ensure that network adapter is enabled for
RPL
3. Network adapter (Advise network
administrator of new MAC address)
Chapter 3. Types 6058/6059/6269/6578/6579
167
Message/Symptom
FRU/Action
Computer will not Wake On LAN (if applicable)
1. Check power supply and signal cable
connections to network adapter
2. Ensure that the operating system settings are
set to enable Wake on LAN
3. Ensure Wake On LAN feature is enabled in
Setup/Configuration. (See “Setup Utility
program” on page 122.)
4. Ensure network administrator is using correct
MAC address
5. Ensure no interrupt or I/O address conflicts
6. Network adapter (advise network
administrator of new MAC address)
Dead computer. See “Power supply” on page 108.
1. Power Supply
2. System Board
Diskette drive in-use light remains on or does not
light when drive is active.
1. Diskette Drive
2. System Board
3. Diskette Drive Cable
Flashing cursor with an otherwise blank display.
1. System Board
2. Primary Hard Disk Drive
3. Hard Disk Drive Cable
Incorrect memory size during POST
1. Run the Memory tests
2. Memory Module
3. System Board
″Insert a Diskette″ icon appears with a
known-good diagnostics diskette in the first
3.5-inch diskette drive.
1. System Board
2. Diskette Drive Cable
3. Network Adapter
Intensity or color varies from left to right of
characters and color bars
1. Display
No power or fan not running
1. See “Power supply” on page 108
Non-system disk or disk error-type message with
a known-good diagnostic diskette.
1. Diskette Drive
2. System Board
2. System Board
3. Diskette Drive Cable
Other display symptoms not listed above
(including blank or illegible display)
1. See “Display” on page 110
2. System Board
3. Display
168
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Message/Symptom
FRU/Action
Power-on indicator or hard disk drive in-use light
not on, but computer works correctly
1. Power Supply
2. System Board
3. LED Cables
Printer problems
1. See “Printer” on page 107
Program loads from the hard disk with a
known-good diagnostics diskette in the first
3.5-inch diskette drive
1. Run Setup
2. Diskette Drive
3. Diskette Drive Cable
4. System Board
5. Power Supply
Drives not recognized by the Fixed Disk diagnostic 1. Remove the first drive that does not show up
(e.g., you have six drives but the fixed disk test
and rerun the Fixed Disk diagnostic. If the
only shows three)
remaining drives then show up, replace the
drive you removed.
Hang during Fixed Disk diagnostic
1. Remove the hard file being tested at the time
of the hang.
2. Rerun the diagnostic.
3. If successful, replace the drive you removed.
RPL computer cannot access programs from its
own hard disk.
1. If network administrator is using LCCM
Hybrid RPL, check startup sequence:
a. First device - network
b. Second device - hard disk
2. Hard disk drive
RPL computer does not RPL from server
1. Check startup sequence
2. Check the network adapter LED status
Serial or parallel port device failure (system board
port)
1. External Device Self-Test OK?
2. External Device
3. Cable
4. System Board
Serial or parallel port device failure (adapter port)
1. External Device Self-Test OK?
2. External Device
3. Cable
4. Alternate Adapter
5. System Board
Chapter 3. Types 6058/6059/6269/6578/6579
169
Message/Symptom
FRU/Action
Some or all keys on the keyboard do not work
1. Keyboard
2. Keyboard Cable
3. System Board
170
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Undetermined problems
Check the power supply voltages. See “Power supply” on page 108. If the
voltages are correct, return here and continue with the following steps.
1. Power-off the computer.
2. Remove or disconnect the following components (if installed) one at a
time.
a. Non-IBM devices
b. External devices (modem, printer, or mouse)
c. Any adapters
d. Memory modules
Before removing or replacing memory modules, see “System board
memory” on page 135.
e. Extended video memory
f. External Cache
g. External Cache RAM
h. Hard disk drive
i. Diskette drive
3. Power-on the computer to re-test the system.
4. Repeat steps 1 through 3 until you find the failing device or adapter.
If all devices and adapters have been removed, and the problem continues,
replace the system board. See “Replacing a system board” on page 125.
Chapter 3. Types 6058/6059/6269/6578/6579
171
Model tables - Country/Region/Language
Note: For model information, please refer to IBM online at
http://www.ibm.com, then select support to find model information for
Types 6058/6059/6269/6578/6579 models.
Use this table to identify the country/region/language of specific models. In
most cases, country/region or language designation will be identified by the
last digit of the model number.
EMEA
Model
EMEA preload
xxG
North America
Model
U.S. English
xxU
Canadian French
xxF
Latin America
Model
Portuguese (Brazil)
xxP
L.A. Spanish
xxS
Asia Pacific (AP)
Model
A.P. English (Australia, New Zealand)
xxA
Japan (Japanese)
xxJ
Hong Kong (A.P. English)
xxD
Hong Kong (Chinese)
xxM
China (Chinese)
xxC
China (A.P. English)
xxD
Thailand (Thai)
xxT
Taiwan (Chinese)
xxV
172
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Parts - Types 6058/6059/6269/6578/6579
Chapter 3. Types 6058/6059/6269/6578/6579
173
Parts listing
Each FRU is available for all types/models, unless specific types or models
are given.
Index
1
2
3
3
3
3
4
5
5
6
6
174
6649
System (Types 6058/6059/6269/6578/6579)
TOP COVER ASM
5.25 DASD BRACKET
CD-ROM DRIVE - 40x (6058 - PAx, PBx) (6578 - LAx, LBx, NCx, NDx,
PAx, RAx, RBx, E4L, EPS, KQG, KSG, RAA, RBA)
CD-ROM DRIVE - 48x (6058 - TAx, TBx, THU, THF, THS, THP, THA,
THT, THM, THV, HD, THG, THC, THJ) (6269 -C2x, D2x, E2x, M2x,
N2x, K2x, L2x, N7x, N8x, P9x, R1x,
R2x,P7x,P8x,F2x,G2x,P3x,H2x,H6x,HCx,J4x,A2x, A6x, R4x, R6x, RBx,
RAx, U3x, U6x,V1x,V3x,UAG,UBG, VAG, VBG, K7S, KDS, KES, UCG,
KCS, KAS, S1G, S2G, SAU, AFU, AGU, V4U, V5G) (6578 - PEx, PFx,
RFx, K7G, K8G, TAx, TBx, TCx, TDx, KAU, DWS, TGU, THU, THF,
THS, THP, THG, THA, THT, THC, THM, THV, THD, THJ, VDJ, VEJ,
VGG, VGC, VGV, TLG, TMG) (6579 - LDx, LEx, NAx, NBx, PCx, PDx,
RAx, RBx, TAx, TBx, TCx, TDx, TEx, TGx, RKx, RAA, RBA, RCG, TEG,
TKU, VHU, VDA, VEA, VFJ, VGJ)
CD-ROM DRIVE - 48x (PRIMARY)(6058 - TAx, TBx, THU, THF, THS,
THP, THA, THT, THM,THV,THD,THG,THC,THJ) (6059 - LDx, LEx,
NAx, NBx, PCx, PDx) (6579 - LDx, LEx, NAx, NBx, PCx, PDx, RAx,
RBx, TAx, TBx, TCx, TDx, TEx, TGx, RJx,
RKx,RAA,RBA,RCG,TEG,TKU,VHU,VDA,VEA,VFJ,VGJ)
CD-ROM DRIVE - 48x (OPTIONAL)(6578 - PEx, PFx, REx, RFx, K7G,
K8G, TAx, TBx, TCx,TDx,KAU, DWS, TGU, THU,D8V, TLG, TMG)
BEZEL KIT
3.5″ 1.44MB DISKETTE DRIVE
3.5″ 1.44MB DISKETTE DRIVE - JAPAN
10.1GB EIDE HARDFILE (6269 - C1x, C2x, D1x, D2x, E1x, E2x, M1x,
M2x, N1x, N2x, K1x, K2x, L1x, L2x, D3A, D3T, D3G, D3C, D3D, D3M,
D3V, D4x, D6G, F1x, F3x, F4x, F6x, G1x, N3x, N4x, N5x, N7x, N8x, P2x,
P4x, P5x, P9x, R1x, R2x, P7x, PBx, F2x, G2x, P1x, P3x, J2S, G3x,
H1x,H2x,H4x,H5x,H6x,H9x,HCx, J4x, A2x, A3x, A5x, A6x, R4x, R6x,
RBx,R8x, RAx, U3x, U5x,U6x,V1x,V2x,V3x,FAG,HAG,HBG,AAG,ABG,
UAG, UBG,VAG,VBG, K7S, J5S, KDS, KES, HEG, ACG, UCG, KCS,
KAS, AGU, V4U) (6058 - LCx, LDx)(6578 - GAx, GBx, LCx, LDx, K7G,
K8G)(6059 - GAx, GBx, LAx, LBx) (6579 - GAx, GBx, LAx, LBx)
20.4GB EIDE HARDFILE 5400 RPM(6269 - none)(6058 - NAx, NBx, PAx,
PBx, RAx, RBx, TAx, TBx, THU, THF, THS, THP, THA, THT, THM,
THV, THD, THG, THC, THJ) (6578 -LAx, LBx, NAx, NBx, NCx, NDx,
PAx, PBx, RAx, RBx, PCx, PDx, PEx, PFx, RCx, RDx, REx, RFx, RGx,
TAx, TBx, TCx, TDx, TEx, E4L, EPS, KAU, KQG, KSG, DWS, TGU,
THU, THF, THS, THP, PHG, THA, THT, THC, THM, THV, THD, THJ,
VFM,VFD, VGG, VGC,VGV, D8V, QYV, TLG, TMG, RAA, RBA) (6579 LDx, LEx, NCx, NDx, PAx, PBx,TCx, TDx, RJx, RKx, RCG, TEG, TEx,
TKU)
FRU No.
06P2732
09N5746
09N0879
19K1529
09N0735
24P3603
09N5732
75H9550
75H9552
36L8681
09N0705
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Index
6
6
7
8
9
10
11
12
13
14
15
15
15
16
16
17
18
18
18
18
18
18
18
18
18
18
18
18
18
18
System (Types 6058/6059/6269/6578/6579)
20.4GB EIDE HARDFILE (OPTIONAL)(6578 - LAx, LBx, NAx, NBx,
NCx, NDx, PAx, PBx, RAx, RBx, PCx, PDx, PEx, PFx, RCx, RDx, REx,
RFx, RGx, TAx, TBx, TCx, TDx, TEx, E4L, EPS, KAU, KQG, KSG, DWS,
TGU, TLG, TMG)
30.0GB EIDE HARDFILE 7200RPM (6059 - NAx, NBx, PCx, PDx)(6579 NAx, NBx, PCx, PDx, RAx, RBx, TAx, TBx, TGx, RAA, RBA, VHU,
VDA, VEA,VFJ,VGJ)
DASD RAIL KIT
3.5 DASD BRACKET
RFID ANTENNA
CHASSIS ASM
CONTROL PANEL ASM (all)
SPEAKER with CABLE ASM
92MM FAN ASM w/grommets
FAN/SPEAKER BRACKET
SYSTEM BD W/O MEM/PROC/POV/MERLOT
SYST BD MERLOT W/POV CARD(6059/6579 only)
SYSTEM BOARD(6269-All except Refresh 3 models)
PLANAR EMC SHIELD KIT(6269 only)
PLANAR EMC SHIELD KIT
NVidia AGP4/16MB VIDEO ADAPTER(6059 - all) (6578 - TCx,
TDx)(6579 - LDx, LEx, NAx, NBx, PCx, PDx, TAx, TBx, TGx,VDA,VEA)
CELERON 533MHz(6269 - C1x, C2x, 20U)(6058/6059/6578/6579 - none)
CELERON 566MHz(6269 - D1x, D2x, 30U, D3A, D3T, D3G, D3C, D3D,
D3M, D3V, D4x, D6G)(6058/6059/6578/6579 - none)
CELERON 600 MHz(6269 - E1x, E2x, 40U)(6058/6059/6578/6579 - none)
CELERON 633 MHz(6269 - F1x, F3x, F4x, F6x, F2x, FAG, 42U, K3V, D3S,
D4S)(6058/6059/6578/6579 - none)
CELERON 667 MHz(6269 - G1x, G2x, 44U, G3x, G4x, G5x, HAG,
HBG)(6058/6059/6578/6579 - none)
CELERON 700 MHz(6269 - H1x, H2x, 46U, H4G, H3x, H5x, H6x, H7x,
H9x, HCx, HDU, HEG)(6058/6059/6578/6579 - none)
CELERON 733 MHz(6269 - J1x, JAx, J4x)(6058/6059/6578/6579 - none)
CELERON 766 MHz(6269 - A1x, A2x, A3x, A4x, A5x, A6x, AAG, ABG,
ADU, ACG, SAU, AHG)(6058/6059/6578/6579 - none)
CELERON 800 MHz(100 BUS/800 MHz/128KB L2 CACHE) FLIP CHIP
WITH HEAT SINK (all)
PiII COPPERMINE 650 MHz(6269 - K1x, K2x,
7OU)(6058/6059/6578/6579 - none)
PiII COPPERMINE 667MHz(6269 - M1x, M2x, 50U, J2S, K7S, KDS, KES,
KCS)(6058/6059/6578/6579 - none)
PIII COPPERMINE 667MHz (6578/6579 - GAx, GBx)
PIII COPPERMINE 700MHz(6269 - L1x, L2x, 8OU )
PIII COPPERMINE 733MHz (6058 - LCx, LDx)(6059/6578 - LAx, LBx,
L1U, LCx, LDx) (6579 - LAx, LBx, LDx, LEx, L1U)
FRU No.
19K1557
09N0925
19K5331
06P2734
03K9654
06P2731
37L5092
01K4909
33L2594
09N5763
09K9982
10K1195
19K5060
10K1540
09N5770
19K5340
09N9307
06P3004
19K5067
06P7163
22P2476
33L2754
24P5586
24P5583
24P5748
19K5068
37L1534
10K0863
19K5077
10K0864
Chapter 3. Types 6058/6059/6269/6578/6579
175
Index
18
18
18
18
18
18
18
18
18
18
18
18
18
18
176
6649
System (Types 6058/6059/6269/6578/6579)
PIII COPPERMINE 733MHz(6269 - N1x, N2x, 60U, N3x, N4x, N5x, N7x,
N8x, J5S,KAS)(6058/6059/6578/6579 - none)
PIII COPPERMINE 800MHz (6058 - NAx, NBx)(6059/6578 - NAx, NBx,
NCx, NDx, N1U, E4L) (6579 - NAx, NBx, N1U, NCx, NDx)
PIII COPPERMINE 800MHz (OPTIONAL TO 25P4964)(6269 - P2x, P4x,
P5x, P9x, P7x, P8x, P1x, P3x, 9OU, D5S, D6S) (6579 - RAx, RBx, R1U,
RJx, RKx, RAA, RBA, RCG)
PIII COPPERMINE 800MHz (PRIMARY) (6269 - P2x, P4x, P5x, P9x, P7x,
P8x, P1x, P3x, 9OU, D5S, D6S)
PIII COPPERMINE 866MHz(6269 - R1x, R2x, R3x, R4x, R5x, R6x, RBx,
R7x, R8x, RAx, S1G, DFS)
PIII COPPERMINE 866MHz (6058 - PAx, PBx)(6578 - PAx, PBx, P1U,
PCx, PDx, PEx, PFx, K7G,K8G, EPS, KAU, DWS) (6579 PAx,PBx,PCx,PDx,P1U)
COPPERMINE 866MHz (6578 - PAx, PBx, P1U, PCx, PDx, PEx, PFx,
K7G, K8G, EPS, KAU, DWS) (6579 - PAx, PBx, PCx, PDx, P1U)
COPPERMINE 866MHz (6578 -PAx, PBx, P1U, PCx, PDx, PEx, PFx,
K7G, K8G, EPS, KAU, DWS)(6579 - PAx,PBx,PCx,PDX,P1U)
PIII (COPPERMINE) 933MHz(6058 - RAx,RBx) (6269 - U1x, U2x, U3x,
U4x, U5x, U6x, UAG, UBG, UDU, UCG, S2G)(6578 - RAx, RBx, RCx,
RDx, REx, RFx, R1U, RGx, KQG, KSG,QYV, RAA, RBA)(6579 - RAx,
RBx, R1U, RJx, RKx)(6579 - RAx, RBx,R1U,RJx,RKx,RAA,RBA,RCG)
PIII (COPPERMINE) 933MHz (6058 - RAx, RBx) (6578 - RAx, RBx, RCx,
RDx, REx, RFx, R1U, RGx, KQG, KSG,QYV, RAA, RBA) (6579 - RAx,
RBx, R1U, RJx, RKx, RAA, RBA, RCG)
PIII (COPPERMINE) 933MHz (6269 - U1x, U2x, U3x, U4x, U5x, U6x,
UAG, UBG, UDU, UCG, S2G) (6578 - RAx, RBx, RCx, RDx, REx, RFx,
R1U, RGx, KQG, KSG, QYV, RAA, RBA) (6579 -RAx, RBx, R1U, RJx,
RKx, RAA, RBA, RCG)
COPPERMINE 1000MHz PROCESSOR(6058 - TAx, TBx, THU, THF,
THS, THP, THA, THT, THM, THV, THD, THG, THC, THJ)(6269 - V1x,
V2x, V3x, VAG, VBG, VDU, S4U, V4U, V5U)(6578TAx,TBx,TCx,TDx,TEx,T2U, TFU, TGU, THU, THF, THS, THP, THG,
THA, THT, THC, THM, THV, THD, THJ, VDJ, VEJ, VFM, VFD, VGG,
VGC, VGV ,D8V, TLG, TMG) (6579 - TAx, TBx, TCx, TDx, TEx, TGx,
T2U, TEG, TKU, VHU, VDA, VEA, VFJ, VGJ)
PROCESSOR HEATSINK AND CLIP(6269 - P1x, P2x, P3x, P4x, P5x,
P7x, P8x, P9x, R1x, R2x, 9OU, A1x, A2x, A3x, A4x, A5x, A6x, R3x, R4x,
R5x, R6x, RBx, R7x, R8x, RAx, AAG, ABG, ADU, AJG, D5S, D6S, ACG,
S1G, SAU, A7G, A7S, A7P, A8S, A8P, A9P, A9S, AFU, AGU, AEU, AHG)
PROCESSOR HEATSINK AND CLIP(6269 only - C1x, C2x, 20U)
FRU No.
37L5338
10K1196
19K7535
25P4964
19K7536
19K7539
25P2778
22P4385
19K7535
19K7537
25P0719
22P3415
10K1689
06P2446
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Index
18
19
19
20
21
22
23
24
24
24
System (Types 6058/6059/6269/6578/6579)
FRU No.
PROCESSOR HEATSINK AND CLIP(6269 only-D1x, D2x, D3A, D3T,
06P2454
D3G, D3C, D3D, D3M, D3V, D4x, D6G, E1x, E2x, F1x, F2x, F3x, F4x,
F6x, G1x, G2x, G3x, H1x, H2x, J2S, K1x, K2x, L1x, L2x, M1x, M2x, N1x,
N2x, N3x, N4x, N5x, N7x, N8x, 30U, 40U, 42U, 44U, 46U, 50U, 60U,
70U, 80U, H4G, H9G, K3V, H3x, H5x, H6x, H7x, H9x, HCx,
J1x,JAx,J4x,FAG,HAG,HBG,HDU,D3S,K7S,J5S,KDS,KES,HEG,D4S,KCS,KAS,
DFS)
33L3072
MEMORY 64MB SDRAM (6058 - LCx,LDx,NAx,NBx)(6269 - C1x, C2x,
D1x, D2x, E1x, E2x, M1x, M2x, N1x, N2x, K1x, K2x, L1x, L2x, D4x, F1x,
N3x, P2x, R1x, G1x, P7x, F2x, G2x,P1x,P3x,J2S,H1x,H2x,K3V,
G4x,G5x,H3x,H4x, H5x, H6x, H7x, J1x, JAx, A1x, A2x,A3x,A4x,R3x,R4x,
R5x, R6x, R7x, U1x, U2x, U3x, U4x, U5x, V1x, HAG, AAG, UAG, VAG,
HDU, ADU, D3S, D5S, D6S, K7S, J5S, KDS, KES, HEG, ACG,
UCG,D4S,KCS,KAS,S1G, S2G, A7G, A7S, A7P, A8S, A8P, A9S,A9P, AGU,
AEU, V4U, AHG, V5G)(6578 - GAx, GBx, LCx, LDx, NAx, NBx, PCx,
PDx, K7G, RGx, TEx, KQG, TLG)(6059/6579 - GAx, GBx, LAx, LBx,
NCx, NDx, PAx, PBx)
33L3074
MEMORY 128MB SDRAM (6058 -PAx,PBx, RAx, RBx, TAx,
TBx)(6059-all)(6269 - D3A, D3T, D3G, D3C, D3D, D3M, D3V, D6G, F3x,
F4x, F6x, N4x, N5x, N7x, N8x, P4x, P5x, P9x, R2x, P8x, G3x, H9x, HCx,
J4x, A5x, A6x, RBx, RAx, U6x, V2x, V3x, FAG, HBG, ABG, AJG, UBG,
VBG, UDU, VDU, S4U, SAU, DGS, AFU) (6578 -LAx, LBx, NCx, NDx,
PAx, PBx, RAx, RBx, PEx, PFx,RCx, RDx, REx, RFx, K8G,TAx, TBx, TCx,
TDx, T2U, E4L, EPS, KAU, KSG, DWS, TGU, VDJ, VEJ, VFM, VFD,
VGG, VGC, VGV, D8V, TMG, RAA, RBA) (6579 - LDx, LEx, NAx, NBx,
PCx, PDx, RAx, TAx, TBx, TCx, TDx, TEx, TGx, T2U, RJx,RKx,RAA,
RBA,RCG,TEG,VDA,VEA,VFJ,VGJ)
AIR BAFFLE DUCT
06P2733
I/O CAM BRACKET
09N5734
KEYLOCK ASM
09K9829
C2 SWITCH ASM
09K9827
155W POWER SUPPLY
00N7685
155W POWER SUPPLY - JAPAN (6058 - LCJ, LDJ, NAJ, NBJ, PAJ, PBJ,
00N7687
RAJ, RBJ, TAJ, TBJ, LCG, LDG, NAG, NBG, PAG, PBG, RAG, RBG,
TAG, TBG, THG, THJ)(6059 - NAJ, NBJ, PCJ, PDJ, NAG, NBG, PCG,
PDG) (6578 - LCJ, LDJ, NAJ, NBJ, PAJ, PBJ, RAJ, RBJ, PEJ, PFJ, RCJ,
RDJ, REJ, RFJ, TAJ, TBJ, LAG, LBG, LCG, LDG, NAG, NBG, NCG,
NDG, PAG, PBG, RAG, RBG, RCG, RDG, REG, RFG, K7G, K8G, TAG,
TBG, TCG, TDG, KQG, KSG, THG, THJ, VDJ, VEJ, VGG)(6579 - LDJ,
LEJ, NAJ, NBJ, PAJ, PBJ, PCJ, PDJ, TAJ, TEJ, TGJ, NAG, NBG, PDG,
RAG, RBG, TAG, TBG, RCG, TEG,VFJ,VGJ)
00N7689
155W POWER SUPPLY - CHINA(6058 - LCC, LDC, NAC, NBC, PAC,
PBC, RAC, RBC, TAC, TBC, THC)(6578 - GAC, GBC, LAC, LBC, LCC,
LDC, NAC, NBC, NCC, NDC, THC, VGC, D8V, QYV, PAC, PBC, RCC,
RDC, TAC, TBC, TEC)(6579 - LAC, LBC, LDC, LEC, NAC, NBC, NCC,
NDC, PAC, PBC, PCC, PDC, TAC, TEC)(6059 - NAC, NBC, PCC, PDC)
5.25″ DASD BRACKET HANDLE
09N5747
Chapter 3. Types 6058/6059/6269/6578/6579
177
Index
178
6649
System (Types 6058/6059/6269/6578/6579)
3.5″ DASD BRACKET HANDLE
CABLE HARDFILE - ATA
FOOT (4)
BEZEL KIT
CABLE DISKETTE DRIVE
MOUSE - 2 Button(6058/6269/6578 - all)(6579 - TAx, TBx, TCx, TDx,
TEx, TGx, T2U,TEG,TKU,VHU,VDA,VEA,VFJ,VGJ)
MOUSE - Scrollpoint(6059)(6579 - GAx, GBx, LAx, LBx, LDx, LEx, L1U,
NAx, NBx, NCx, NDx, N1U, PAx, PBx, PCx, PDx, P1U, RAx, RBx, R1U,
RJx, RKx, RAA, RBA, RCG)
MISC. HARDWARE KIT (6269/6578/6579 - all)
ATA-66 CABLE ASM (2 drop)(6269/6578/6579 - all)
CDROM AUDIO CABLE (6269/6578/6579 - all)
DUAL USB CABLE(6058/6059/6578/6579 only)
LITHIUM BATTERY
PLANAR LOCATION LABEL(6269 only)
PLANAR INFO LABEL KIT
EMC SHIELD FOR 5.25″ BAY (6269 - all)
EMC SHIELD FOR 5.25″ BAY
NAMEPLATE
INTERPOSER CABLE ASM(6269 only)
ACCTON ETHERNET CARD(6269 - C2x, D2x, E2x, M2x, N2x, K2x, L2x,
D3x, F4x, N3x, N5x, N8x, P2x, P5x, P9x, F2x, G2x, P3x, G3x, H2x, H4x,
H5x, H6x, H9x. HCx, J4x, A2x, A3x, A5x, A6x, R4x, R6x, RBx, R8x, RAx,
U3x, U5x, U6x, V1x, V2x, V3x, FAG, HAG, HBG, AAG, ABG,UAG,
UBG, VAG, VBG, K7S, KES, HEG, ACG, UCG, KAS, S1G, S2G, S4U,
SAU, A7S, A7P, A8S, A8P, A9S, A9P, AFU, AGU, AHG, V5G )
(6058/6059/6578/6579 - none)
ROULETTE ETHERNET ADAPTER (6058 - PAx, PBx, TAx,
TBx,THU,THF,THS,THP,THA,THT,THM,THV,THD,THG,THC,THJ )(6578
-LAx,LBx,NCx,NDx,PAx,PBx,RAx,RBx,PEx,PFx,REx, THU, THF, THS,
THG, THA, THT, THC,THM, THV, THD, THJ, VDJ, VEJ, VFM, VFDM
VGG, VGC, TFU, THG, THU, RFX, ,K7G,K8G,TAx,TBx,TCx,
TDx,TEx,E4L,EPS,KAU,KQG,KSG,DWS,D8V, TLG, TMG, RAA,
RBA)(6059/6579 - all)
VIDEO CARD 4xAGP DONGLE (6578 - PEx, PFx, REx, RFx,TCx,TDx)
(6059 - all)(6579 - LDx, LEx, NAx, NBx, PCx, PDx, RAx,RBx, TAx, TBx,
TGx, RAA, RBA, VDA, VEA)
NVidia P09/32MB VIDEO ADAPTER (6578 - PEx, PFx, REx, RFx) (6579
- RAx, RBx,RAA,RBA,VDA,VEA)
ENET ADAPTER FERRITE ( 6059 - NAJ, NBJ, PCJ, PDJ) (6579 - LDJ,
LEJ, NAJ, NBJ, PAJ, PBJ, PCJ, PDJ)
FRU No.
09N5748
37L4525
03K9655
09N5732
33L2596
10L6145
28L1865
09N5764
37L5098
75H9219
22P1188
33F8354
10K1698
09N5715
19K5548
20L3073
09N5733
06P2401
19K4309
19K4885
37L5566
09N5033
06P7059
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Index
System (Types 6058/6059/6269/6578/6579)
FRU No.
SYSTEM BOARD - GIGABYTE PLANAR (6269 - G4x, G5x, H3x, H4x,
24P5565
H5x, H6x, H7x, H9x, HCx, J1x, JAx, J4x, A1x, A2x, A3x, A4x, A5x, A6x,
R3x, R4x, R5x, R6x, RBx,R7x, R8x, RAx, U1x, U2x, U3x, U4x, U5x, U6x,
V1x, V2x, V3x, FAG, HAG, HBG, AAG, ABG, UAG, UBA, VAG, VBG,
HDU, ADU, UDU, VDU, KDS, KES, HEG, ACG, UCG, D4S, KCS, KAS,
S1G, S2G, S4U, SAU, A7S, A7P, A8S, A8P, A9S, A9P, AFU, AGU, AEU,
V4U, AHG, V5G)
MEMORY 256MB SDRAM (6058 -THU, THF, THS, THP, THA, THT,
33L3076
THM, THV, THD, THG, THC, THJ) (6269 - all) (6578 - TFU, THU, THF,
THS, THP, THG, THA, THT, THC, THM,THV,THD,THJ,QYV) (6579 TKU,VHU)
10GB HARDFILE EIDE 5400rpm (PRIMARY) (6269 -C1x, C2x, D1x, D2x, 19K1476
E1x,E2x,M1x,M2x,N1x,N2x,K1x,
K2x,L1x,L2x,D3A,D3T,D3G,D3C,D3D,D3M,D3V,
D4x,D6G,F1x,F3x,F4x,F6x,G1x,N3x,N4x,N5x,N7x, N8x, P2x, P4x, P5x,
P9x, R1x,
R2x,P7x,P8x,F2x,G2x,P1x,P3x,J2S,G3x,H1x,H2x,H4x,H5x,H6x,H9x,HCx,J4x,A2x,A3x,A5x,A6x,R4x,R6x,RBx,R8x,RAx,U3x,U5x,U6x
AGU, V4U)
20GB IDE 5400rpm HARDFILE (6269 - G4x, G5x, H3x, H7x, J1x, JAx,
19K1560
A1x, A4x, R3x, R5x, R7x, U1x, U2x, U4x, D3S, D5S, D6S, D4S, S1G, S2G,
SAU, DFS, A7G, A7S, A7P, A8S, A8P, A9S, A9P, AFU, AHG, AJG, V5G)
30.0GB ATA - 100, 7200RPM Hardfile (6269 - S4U)(6578-TFU,VDJ,VEJ)
19K1567
(6578 - TFU, VDJ, VEJ)
8x4x32x CDROM READ/WRITE (6269- S4U)
09N0891
LC 2.3 ETHERNET CARD (6269 - F3x, N4x, P4x)
34L1209
GVC MODEM (Domestic) (PRIMARY) (6269 - KDS, KES, KCS)
09N1677
MODEM (DOMESTIC) (6269 - SAU)
09N1678
MODEM (DOMESTIC) (6269 - SAU)
19K2965
2ND SERIAL PORT CABLE ASM (6269 - all)
24P9065
8X CD-RW, LG, WHITE, NO HD PH (6578-TFU)
06P5163
COPPERMINE CELERON 800MHz (100 BUS/800MHz/128Kb L2
25P2779
CACHE) ″D0″ STEP LEVEL FLIP CHIP WITH HEATSINK 09N4373
(NOTE: PRIME P/N TO 10K1196) (6058 - NAx,NBx) (6578 - NAx, NBx,
NCx, NDx, N1U, E4L) (6579 - NAx, NBx, N1U,NCx,NDx)
25P0834
COPPERMINE CELERON 800MHz (100 BUS/800MHz/128Kb L2
CACHE) ″C0″ STEP LEVEL FLIP CHIP WITH HEATSINK (NOTE:
PRIME P/N TO 24P5784) (6269 - A7G, A7S, A7P, A8S, A8P, A9P, AFU,
AGU, AEU, AJG)
COPPERMINE CELERON 800MHz (100 BUS/800MHz/128Kb L2
24P5784
CACHE) ″D0″ STEP LEVEL FLIP CHIP WITH HEATSINK (NOTE:
PRIME P/N TO 25P0834) (6269 - A7G, A7S, A7P, A8S, A8P, A9P, AFU,
AGU, AEU, AJG)
Chapter 3. Types 6058/6059/6269/6578/6579
179
Index
System (Types 6058/6059/6269/6578/6579)
FANSINK NON-IHS 900 MHz (6058 - RAx, RBx, TAx, TBx, THA, THU,
THF, THS, THP, THT, THM, THV, THD, THG, THC, THJ) (6578 - RAx,
RBx, RCx, RDx, REx, RFx, R1U, RGx, KQG, KSG, QYV, RAA, RBA, TAx,
TBx, TCx, TDx, TEx, T2U, TFU, TGU, THU, THF, THS, THP THG, THA,
THT, THC, THM, THV, THD, THJ, VDJ, VEJ, VFM, VFD, VGG, VGC,
VGV, DBV, TLG, TMG) (6579 - RAx, RBx, R1U, RJx, RKx, RAA, RBA,
RCG, TAx, TBx, TCx, TDx, TEx, TGx, T2U, TEG, TKU, VHU, VDA,
VEA, VFJ, VGJ)
FANSINK, IHS 866 - 1.10 GHz (6058 - PAx, PBx, RAx, RBx, TAx, TBx,
THU, THF, THS, THP, THA, THT, THM, THV, THD, THG, THC, THJ)
(6578 - RAx, RBx, RCx, RDx, REx, RFx, R1U, RGx, KQG, KSG, QYV,
RAA, RBA, TAx, TBx, TCx, TDx, TEx, T2U, TFU, TGU, THU, THF, THS,
THP THG, THA, THT, THC, THM, THV, THD, THJ, VDJ, VEJ, VFM,
VFD, VGG, VGC, VGV, D8V, TLG, TMG) (6579 - RAx, RBx, R1U, RJx,
RKx, RAA, RBA, RCG, TAx, TBx, TCx, TDx, TEx, TGx, T2U, TEG, TKU,
VHU, VDA, VEA, VFJ, VGJ)
HEATSINK, NON-IHS 566 - 866 MHz (6058 - LCx, LDx, NAx, NBx,
PAx, PBx) (6578 - GAx, GBx, LAx, LBx, L1U LCx, LDx, NAx, NBx, NCx,
NDx, N1U, E4L, PAx, PBx, P1U, PCx, PDx, PEx, PFx, K7G, K8G, EPS,
KAU, DWS) (6579 - GAx, GBx, LAx, LBx, LDx, LEx, L1U NAx, NBx,
N1U, NCx, NDx, PAx, PBx, PCx, PDx, P1U)
FRU No.
06P2458
22P4370
09N4372
Keyboards - PCNext Lite Pearl White
US ENGLISH
FRENCH CANADIAN 058
FRENCH CANADIAN 044
LA/SPANISH
BRAZIL - PORTUGUESE
ARABIC
BELGIUM - FRENCH
BELGIUM - ENGLISH
BULGARIAN
CZECH
DANISH
DUTCH
FRENCH
GERMAN
GREEK
HEBREW
HUNGARIAN
ITALIAN
NORWEGIAN
180
6649
37L2514
37L0912
37L2515
37L2516
28L1826
37L2518
37L2519
37L2520
37L2521
37L2522
37L2523
37L2524
37L2525
37L2526
37L2527
37L2528
37L2529
37L2531
37L2532
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
POLISH
PORTUGUESE
ROMANIAN
RUSSIAN
SERBIAN - CYR
SLOVAK
SPANISH
SWEDISH/FINNISH
SWISS - FRENCH/GERMAN
TURKISH - ID 179
TURKISH - ID 440
UK ENGLISH
YUGOSLAVIAN
UK ENGLISH (ISO)
JAPANESE
CHINESE
KOREAN
THAI
37L2533
37L2534
37L2535
37L2536
37L2537
37L2538
37L2539
37L2540
37L2541
37L2542
37L2543
37L2544
37L2545
37L2546
37L2547
37L2548
28L1860
37L2550
Computer Power Cords
ARABIC
AUSTRALIAN
BELGIAN
BULGARIAN
CANADIAN
CZECH
DENMARK
FINLAND
FRANCE
GERMAN
HUNGARIAN
ISRAEL
ITALIAN
LATIN AMERICAN
NETHERLANDS
NEW ZEALAND
NORWEGIAN
POLISH
PORTUGUESE
SERBIAN
SLOVAKIAN
SOUTH AFRICAN
SPANISH
SWISS
14F0033
93F2365
1339520
1339520
93F2364
1339520
13F9997
1339520
1339520
1339520
1339520
14F0087
14F0069
6952301
1339520
93F2365
1339520
1339520
1339520
1339520
1339520
14F0015
1339520
1339520
Chapter 3. Types 6058/6059/6269/6578/6579
181
SWISS - FRENCH/GERMAN
US ENGLISH
UK - IRELAND
YUGOSLAVIAN
CHILE
ARGENTINA, PARAGUAY, & URUGUAY
14F0051
93F2364
14F0033
1339520
14F0069
36L8880
Recovery CDs
ARGENTINA, PARAGUAY, & URUGUAY
36L8880
Display and Monitor Information
Display and monitor information is available separately and is listed under
“Related Publications” on page vii.
182
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Special tools
The following tools are required to service the computer models/types listed
in this section of the service manual
v Volt-ohm meter, IBM P/N 73G5404
v Wrap Plug, IBM P/N 72X8546
Chapter 3. Types 6058/6059/6269/6578/6579
183
184
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Chapter 4. Related Service Information
Note: The service procedures are designed to help you isolate problems. They
are written with the assumption that you have model-specific training
on all computers, or that you are familiar with the computers,
functions, terminology, and service information provided in this
manual.
Safety information
The following section contains the safety information that you need to be
familiar with before servicing an IBM mobile computer.
General safety
Follow these rules to ensure general safety:
v Observe good housekeeping in the area of the machines during and after
maintenance.
v When lifting any heavy object:
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you
attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action
removes the strain from the muscles in your back. Do not attempt to lift
any objects that weigh more than 16 kg (35 lb) or objects that you think are too
heavy for you.
v Do not perform any action that causes hazards to the customer, or that
makes the equipment unsafe.
v Before you start the machine, ensure that other service representatives and
the customer’s personnel are not in a hazardous position.
v Place removed covers and other parts in a safe place, away from all
personnel, while you are servicing the machine.
v Keep your tool case away from walk areas so that other people will not trip
over it.
v Do not wear loose clothing that can be trapped in the moving parts of a
machine. Ensure that your sleeves are fastened or rolled up above your
elbows. If your hair is long, fasten it.
v Insert the ends of your necktie or scarf inside clothing or fasten it with a
nonconductive clip, approximately 8 centimeters (3 inches) from the end.
© Copyright IBM Corp. 2000
185
v Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for
your clothing.
Remember: Metal objects are good electrical conductors.
v Wear safety glasses when you are: hammering, drilling soldering, cutting
wire, attaching springs, using solvents, or working in any other conditions
that might be hazardous to your eyes.
v After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
v Reinstall all covers correctly before returning the machine to the customer.
Electrical safety
CAUTION:
Electrical current from power, telephone, and communication cables can be
hazardous. To avoid personal injury or equipment damage, disconnect the
attached power cords, telecommunication systems, networks, and modems
before you open the server covers, unless instructed otherwise in the
installation and configuration procedures.
Observe the following rules when working on electrical equipment.
Important: Use only approved tools and test equipment. Some hand tools
have handles covered with a soft material that does not insulate
you when working with live electrical currents.
Many customers have, near their equipment, rubber floor mats
that contain small conductive fibers to decrease electrostatic
discharges. Do not use this type of mat to protect yourself from
electrical shock.
v Find the room emergency power-off (EPO) switch, disconnecting switch, or
electrical outlet. If an electrical accident occurs, you can then operate the
switch or unplug the power cord quickly.
v Do not work alone under hazardous conditions or near equipment that has
hazardous voltages.
v Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
v Before you start to work on the machine, unplug the power cord. If you
cannot unplug it, ask the customer to power-off the wall box that supplies
power to the machine and to lock the wall box in the off position.
186
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
v If you need to work on a machine that has exposed electrical circuits,
observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near
you.
Remember: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical equipment;
keep the other hand in your pocket or behind your back.
Remember: There must be a complete circuit to cause electrical shock. By
observing the above rule, you may prevent a current from passing
through your body.
– When using testers, set the controls correctly and use the approved
probe leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate
you from grounds such as metal floor strips and machine frames.
Observe the special safety precautions when you work with very high
voltages; these instructions are in the safety sections of maintenance
information. Use extreme care when measuring high voltages.
v Regularly inspect and maintain your electrical hand tools for safe
operational condition.
v Do not use worn or broken tools and testers.
v Never assume that power has been disconnected from a circuit. First, check
that it has been powered-off.
v Always look carefully for possible hazards in your work area. Examples of
these hazards are moist floors, nongrounded power extension cables, power
surges, and missing safety grounds.
v Do not touch live electrical circuits with the reflective surface of a plastic
dental mirror. The surface is conductive; such touching can cause personal
injury and machine damage.
v Do not service the following parts with the power on when they are
removed from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
v If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
Chapter 4. Related Service Information
187
– Send another person to get medical aid.
Safety inspection guide
The intent of this inspection guide is to assist you in identifying potentially
unsafe conditions on these products. Each machine, as it was designed and
built, had required safety items installed to protect users and service
personnel from injury. This guide addresses only those items. However, good
judgment should be used to identify potential safety hazards due to
attachment of non-IBM features or options not covered by this inspection
guide.
If any unsafe conditions are present, you must determine how serious the
apparent hazard could be and whether you can continue without first
correcting the problem.
Consider these conditions and the safety hazards they present:
v Electrical hazards, especially primary power (primary voltage on the frame
can cause serious or fatal electrical shock).
v Explosive hazards, such as a damaged CRT face or bulging capacitor
v Mechanical hazards, such as loose or missing hardware
The guide consists of a series of steps presented in a checklist. Begin the
checks with the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power-off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to
measure third-wire ground continuity for 0.1 ohm or less between the
external ground pin and frame ground.
b. The power cord should be the appropriate type as specified in the
parts listings.
c. Insulation must not be frayed or worn.
4. Remove the cover.
5. Check for any obvious non-IBM alterations. Use good judgment as to the
safety of any non-IBM alterations.
6. Check inside the unit for any obvious unsafe conditions, such as metal
filings, contamination, water or other liquids, or signs of fire or smoke
damage.
7. Check for worn, frayed, or pinched cables.
8. Check that the power-supply cover fasteners (screws or rivets) have not
been removed or tampered with.
188
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Handling electrostatic discharge-sensitive devices
Any computer part containing transistors or integrated circuits (ICs) should be
considered sensitive to electrostatic discharge (ESD). ESD damage can occur
when there is a difference in charge between objects. Protect against ESD
damage by equalizing the charge so that the machine, the part, the work mat,
and the person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements
noted here.
2. Make sure that the ESD protective devices you use have been certified
(ISO 9000) as fully effective.
When handling ESD-sensitive parts:
v Keep the parts in protective packages until they are inserted into the
product.
v Avoid contact with other people.
v Wear a grounded wrist strap against your skin to eliminate static on your
body.
v Prevent the part from touching your clothing. Most clothing is insulative
and retains a charge even when you are wearing a wrist strap.
v Use the black side of a grounded work mat to provide a static-free work
surface. The mat is especially useful when handling ESD-sensitive devices.
v Select a grounding system, such as those listed below, to provide protection
that meets the specific service requirement.
Note: The use of a grounding system is desirable but not required to
protect against ESD damage.
– Attach the ESD ground clip to any frame ground, ground braid, or
green-wire ground.
– Use an ESD common ground or reference point when working on a
double-insulated or battery-operated system. You can use coax or
connector-outside shells on these systems.
– Use the round ground-prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and
correct system function. Proper grounding of the electrical outlet can be
verified by a certified electrician.
Safety notices (multi-lingual translations)
The caution and danger safety notices in this section are provided in the
following languages:
v English
Chapter 4. Related Service Information
189
v
v
v
v
Brazilian/Portuguese
Chinese
French
German
v Italian
v Korean
v Spanish
Important: All caution and danger statements in this Netfinity Server Library
begin with a number. This number is used to cross reference an
English caution or danger statement with translated versions of
the caution or danger statement in this section.
For example, if a caution statement begins with a number 1,
translations for that caution statement appear in this section under
statement 1.
Be sure to read all caution and danger statements before
performing any of the instructions.
v Statement 1
DANGER
Electrical current from power, telephone and communication cables is
hazardous.
To avoid a shock hazard:
v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
v Connect all power cords to a properly wired and grounded electrical
outlet.
v Connect to properly wired outlets any equipment that will be attached to
this product.
v When possible, use one hand only to connect or disconnect signal cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
190
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
v Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
v Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached devices.
To Connect
To Disconnect
1. Turn everything OFF.
1. Turn everything OFF.
2. First, attach all cables to devices.
2. First, remove power cords from outlet.
3. Attach signal cables to connectors.
3. Remove signal cables from connectors.
4. Attach power cords to outlet.
4. Remove all cables from devices.
5. Turn device ON.
v Statement 2
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or
an equivalent type battery recommended by the manufacturer. If your
system has a module containing a lithium battery, replace it only with the
same module type made by the same manufacturer. The battery contains
lithium and can explode if not properly used, handled, or disposed of.
Do not:
v Throw or immerse into water
v Heat to more than 100°C (212°F)
v Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
v Statement 3
Chapter 4. Related Service Information
191
CAUTION:
When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic
devices, or transmitters) are installed, note the following:
v Do not remove the covers. Removing the covers of the laser product
could result in exposure to hazardous laser radiation. There are no
serviceable parts inside the device.
v Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
Some laser products contain an embedded Class 3A or Class 3B laser diode.
Note the following:
Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.
v Statement 4
192
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
≥ 32 kg (70.5 lbs)
≥ 55 kg (121.2 lbs)
CAUTION:
Use safe practices when lifting.
v Statement 5
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The
device also might have more than one power cord. To remove all electrical
current from the device, ensure that all power cords are disconnected from
the power source.
2
1
v Statement 10
CAUTION:
Do not place any object weighing more than 82 kg (180 lbs.) on top of
rack-mounted devices.
Importante:
Chapter 4. Related Service Information
193
Todas as instruções de cuidado e perigo da :cit.Netfinity Server Library:ecit.
começam com um número. Este número é utilizado para fazer referência
cruzada de uma instrução de cuidado ou perigo no idioma inglês com as
versões traduzidas das instruções de cuidado ou perigo encontradas nesta
seção.
Por exemplo, se uma instrução de cuidado é iniciada com o número 1, as
traduções para aquela instrução de cuidado aparecem nesta seção sob a
instrução 1.
Certifique-se de ler todas as instruções de cuidado e perigo antes de executar
qualquer operação.
Instrução 1
PERIGO
A corrente elétrica proveniente de cabos de alimentação, de telefone e de
comunicações é perigosa.
Para evitar risco de choque:
v Não conecte ou desconecte cabos e não realize instalação, manutenção ou
reconfiguração deste produto durante uma tempestade com raios.
v Conecte todos os cabos de alimentação a tomadas elétricas corretamente
instaladas e aterradas.
v Conecte todos os equipamentos ao qual esse produto será conectado a
tomadas corretamente instaladas.
v Sempre que possível, utilize apenas uma das mãos para conectar ou
desconectar cabos de sinal.
v Nunca ligue qualquer equipamento quando existir evidência de danos por
fogo, água ou na estrutura.
v Desconecte cabos de alimentação, sistemas de telecomunicação, redes e
modems antes de abrir as tampas dos dispositivos, a menos que
especificado de maneira diferente nos procedimentos de instalação e
configuração.
v Conecte e desconecte cabos conforme descrito na seguinte tabela, ao instalar
ou movimentar este produto ou os dispositivos conectados, ou ao abrir suas
tampas.
194
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Para Conectar:
Para Desconectar:
1. DESLIGUE Tudo.
1. DESLIGUE Tudo.
2. Primeiramente, conecte todos os cabos aos
dispositivos.
2. Primeiramente, remova os cabos de alimentação
das tomadas.
3. Conecte os cabos de sinal aos conectores.
3. Remova os cabos de sinal dos conectores.
4. Conecte os cabos de alimentação às tomadas.
4. Remova todos os cabos dos dispositivos.
5. LIGUE os dispositivos.
Instrução 2
CUIDADO:
Ao substituir a bateria de lítio, utilize apenas uma bateria IBM, Número de
Peça 33F8354 ou uma bateria de tipo equivalente, recomendada pelo
fabricante. Se o seu sistema possui um móídulo com uma bateria de lítio,
substitua-o apenas pelo mesmo tipo de mídulo, do mesmo fabricante. A
bateria contém lítio e pode explodir se não for utilizada, manuseada e
descartada de maneira correta.
.Não:
v Jogue ou coloque na água
v Aqueça a mais de 100C (212F)
v Conserte nem desmonte
Para descartar a bateria, entre em contato com a área de atendimento a
clientes IBM, pelo telefone (011) 889-8986, para obter informações sobre como
enviar a bateria pelo correio para a IBM.
Instrução 3
PRECAUCIÓN:
Quando produtos a laser (unidades de CD-ROM, unidades de DVD,
dispositivos de fibra ítica, transmissores, etc.) estiverem instalados, observe o
seguinte:
Chapter 4. Related Service Information
195
v Não remova as tampas. A remoção das tampas de um produto a laser pode
resultar em exposição prejudicial à radiação de laser. Nenhuma peça
localizada no interior do dispositivo pode ser consertada.
v A utilização de controles ou ajustes ou a execução de procedimentos
diferentes dos especificados aqui pode resultar em exposição prejudicial à
radiação.
PERIGO
Alguns produtos a laser contêm um diodo laser da Classe 3A ou Classe 3B
embutido. Observe o seguinte:
Radiação de laser quando aberto. Não olhe diretamente para o raio a olho nu
ou com instrumentos íticos, e evite exposição direta ao raio.
Instrução 4
196
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
≥ 32 kg (70.5 lbs)
≥ 55 kg (121.2 lbs)
CUIDADO:
Ao levantar a máquina, faça-o com segurança.
Instrução 5
CUIDADO:
Os botões Liga/Desliga localizados no dispositivo e na fonte de alimentação
não desligam a corrente elétrica fornecida ao dispositivo. O dispositivo
também pode ter mais de um cabo de alimentação. Para remover toda a
corrente elétrica do dispositivo, assegure que todos os cabos de alimentação
estejam desconectados da fonte de energia elétrica.
2
1
CUIDADO:
Instrução 10
CUIDADO:
Chapter 4. Related Service Information
197
Não coloque nenhum objeto com peso superior a 82 kg (180 lbs.) sobre
dispositivos montados em rack.
198
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Chapter 4. Related Service Information
199
200
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Chapter 4. Related Service Information
201
202
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Chapter 4. Related Service Information
203
204
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Important:
Toutes les consignes Attention et Danger indiquées dans la bibliothèque
:cit.Netfinity Server:ecit. sont précédées d’un numéro. Ce dernier permet de
mettre en correspondance la consigne en anglais avec ses versions traduites
dans la présente section.
Par exemple, si une consigne de type Attention est précédée du chiffre 1, ses
traductions sont également précédées du chiffre 1 dans la présente section.
Prenez connaissance de toutes les consignes de type Attention et Danger
avant de procéder aux opérations décrites par les instructions.
Notice n 1
DANGER
Le courant électrique passant dans les câbles de communication, ou les
cordons téléphoniques et d’alimentation peut être dangereux.
Pour éviter tout risque de choc électrique:
v Ne manipulez aucun câble et n’effectuez aucune opération d’installation,
d’entretien ou de reconfiguration de ce produit au cours d’un orage.
v Branchez tous les cordons d’alimentation sur un socle de prise de courant
correctement câblé et mis à la terre.
v Branchez sur des socles de prise de courant correctement câblés tout
équipement connecté à ce produit.
v Lorsque cela est possible, n’utilisez qu’une seule main pour connecter ou
déconnecter les câbles d’interface.
Chapter 4. Related Service Information
205
v Ne mettez jamais un équipement sous tension en cas d’incendie ou
d’inondation, ou en présence de dommages matériels.
v Avant de retirer les carters de l’unité, mettez celle-ci hors tension et
déconnectez ses cordons d’alimentation, ainsi que les câbles qui la relient
aux réseaux, aux systèmes de télécommunication et aux modems (sauf
instruction contraire mentionnée dans les procédures d’installation et de
configuration).
v Lorsque vous installez ou que vous déplacez le présent produit ou des
périphériques qui lui sont raccordés, reportez-vous aux instructions
ci-dessous pour connecter et déconnecter les différents cordons.
Connexion
Déconnexion
1. Mettez les unités hors tension.
1. Mettez les unités hors tension.
2. Commencez par brancher tous les cordons sur 2. Débranchez les cordons d’alimentation des
les unités.
prises.
3. Branchez les câbles d’interface sur des
connecteurs.
3. Débranchez les câbles d’interface des
connecteurs.
4. Branchez les cordons d’alimentation sur des
prises.
4. Débranchez tous les câbles des unités.
5. Mettez les unités sous tension.
Notice n 2
ATTENTION:
Remplacez la pile au lithium usagée par une pile de référence identique
exclusivement - voir la référence IBM - ou par une pile équivalente
recommandée par le fabricant. Si votre système est doté d’un module
contenant une pile au lithium, vous devez le remplacer uniquement par un
module identique, produit par le même fabricant. La pile contient du
lithium et présente donc un risque d’explosion en cas de mauvaise
manipulation ou utilisation.
v Ne la jetez pas à l’eau.
v Ne l’exposez pas à une température supérieure à 100 °C.
v Ne cherchez pas à la réparer ou à la démonter.
Pour la mise au rebut, reportez-vous à la réglementation en vigueur.
206
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Notice n 3
ATTENTION:
Si des produits laser sont installés (tels que des unités de CD-ROM ou de
DVD, des périphériques contenant des fibres optiques ou des
émetteurs-récepteurs), prenez connaissance des informations suivantes:
v N’ouvrez pas ces produits pour éviter une exposition directe au rayon
laser. Vous ne pouvez effectuer aucune opération de maintenance à
l’intérieur.
v Pour éviter tout risque d’exposition au rayon laser, respectez les
consignes de réglage et d’utilisation des commandes, ainsi que les
procédures décrites dans le présent document.
DANGER
Certains produits laser contiennent une diode laser de classe 3A ou 3B.
Prenez connaissance des informations suivantes:
Rayonnement laser lorsque le carter est ouvert. évitez de regarder fixement
le faisceau ou de l’observer à l’aide d’instruments optiques. évitez une
exposition directe au rayon.
Notice n 4
Chapter 4. Related Service Information
207
≥ 32 kg (70.5 lbs)
≥ 55 kg (121.2 lbs)
ATTENTION:
Faites-vous aider pour soulever ce produit.
Notice n 5
ATTENTION:
Le bouton de mise sous tension/hors tension de l’unité et l’interrupteur
d’alimentation du bloc d’alimentation ne coupent pas l’arrivée de courant
électrique à l’intérieur de la machine. Il se peut que votre unité dispose de
plusieurs cordons d’alimentation. Pour isoler totalement l’unité du réseau
électrique, débranchez tous les cordons d’alimentation des socles de prise
de courant.
2
1
Notice n 10
ATTENTION:
Wichtig:
208
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Alle Sicherheitshinweise in dieser :cit.Netfinity Server-Bibliothek:ecit. beginnen
mit einer Nummer. Diese Nummer verweist auf einen englischen
Sicherheitshinweis mit den übersetzten Versionen dieses Hinweises in diesem
Abschnitt.
Wenn z. B. ein Sicherheitshinweis mit der Nummer 1 beginnt, so erscheint die
übersetzung für diesen Sicherheitshinweis in diesem Abschnitt unter dem
Hinweis 1.
Lesen Sie alle Sicherheitshinweise, bevor Sie eine Anweisung ausführen.
Hinweis 1
VORSICHT
Elektrische Spannungen von Netz-, Telefon- und Datenübertragungsleitungen
sind gefährlich.
Aus Sicherheitsgründen:
v Bei Gewitter an diesem Gerät keine Kabel anschließen oder l÷sen. Ferner
keine Installations-, Wartungs- oder Rekonfigurationsarbeiten durchführen.
v Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem
Schutzkontakt anschließen.
v Alle angeschlossenen Geräte ebenfalls an Schutzkontaktsteckdosen mit
ordnungsgemäß geerdetem Schutzkontakt anschließen.
v Signalkabel m÷glichst einhändig anschließen oder l÷sen.
v Keine Geräte einschalten, wenn die Gefahr einer Beschädigung durch Feuer,
Wasser oder andere Einflüsse besteht.
v Die Verbindung zu den angeschlossenen Netzkabeln,
Telekommunikationssystemen, Netzwerken und Modems ist vor dem
÷ffnen des Gehäuses zu unterbrechen. Es sei denn, dies ist in den
zugeh÷rigen Installations- und Konfigurationsprozeduren anders
angegeben.
v Nur nach den nachfolgend aufgeführten Anweisungen arbeiten, die für
Installation, Transport oder ÷ffnen von Gehäusen von Personal Computern
oder angeschlossenen Einheiten gelten.
Chapter 4. Related Service Information
209
Kabel anschlieβen:
Kabel l÷sen:
1. Alle Geräte ausschalten und Netzstecker
ziehen.
1. Alle Geräte ausschalten.
2. Zuerst Netzstecker von Steckdose l÷sen.
2. Zuerst alle Kabel an Einheiten anschließen.
3. Signalkabel von Anschlußbuchsen l÷sen.
3. Signalkabel an Anschlußbuchsen anschließen.
4. Alle Kabel von Einheiten l÷sen.
4. Netzstecker an Steckdose anschließen.
5. Gerät einschalten.
Hinweis 2
ACHTUNG:
Eine verbrauchte Batterie nur durch eine Batterie mit der IBM Teilenummer
33F8354 oder durch eine vom Hersteller empfohlene Batterie ersetzen. Wenn
Ihr System ein Modul mit einer Lithium-Batterie enthält, ersetzen Sie es
immer mit dem selben Modultyp vom selben Hersteller. Die Batterie enthält
Lithium und kann bei unsachgemäßer Verwendung, Handhabung oder
Entsorgung explodieren.
Die Batterie nicht:
v mit Wasser in Berührung bringen.
v über 100 C erhitzen.
v reparieren oder zerlegen.
Die ÷rtlichen Bestimmungen für die Entsorgung von Sondermüll beachten.
Hinweis 3
ACHTUNG:
Wenn ein Laserprodukt (z. B. CD-ROM-Laufwerke, DVD-Laufwerke,
Einheiten mit Glasfaserkabeln oder Transmitter) installiert ist, beachten Sie
folgendes.
v Das Entfernen der Abdeckungen des CD-ROM-Laufwerks kann zu
gefährlicher Laserstrahlung führen. Es befinden sich keine Teile innerhalb
des CD-ROM-Laufwerks, die vom Benutzer gewartet werden müssen. Die
Verkleidung des CD-ROM-Laufwerks nicht ÷ffnen.
210
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
v Steuer- und Einstellelemente sowie Verfahren nur entsprechend den
Anweisungen im vorliegenden Handbuch einsetzen. Andernfalls kann
gefährliche Laserstrahlung auftreten.
VORSICHT
Manche CD-ROM-Laufwerke enthalten eine eingebaute Laserdiode der Klasse
3A oder 3B. Die nachfolgend aufgeführten Punkte beachten.
Laserstrahlung bei ge÷ffneter Tür. Niemals direkt in den Laserstrahl sehen,
nicht direkt mit optischen Instrumenten betrachten und den Strahlungsbereich
meiden.
Hinweis 4
Chapter 4. Related Service Information
211
≥ 32 kg (70.5 lbs)
≥ 55 kg (121.2 lbs)
ACHTUNG:
Beim Anheben der Maschine die vorgeschriebenen Sicherheitsbestimmungen
beachten.
Hinweis 5
ACHTUNG:
Mit dem Betriebsspannungsschalter an der Vorderseite des Servers und dem
Betriebsspannungsschalter am Netzteil wird die Stromversorgung für den
Server nicht unterbrochen. Der Server k÷nnte auch mehr als ein Netzkabel
aufweisen. Um die gesamte Stromversorgung des Servers auszuschalten, muß
sichergestellt werden, daß alle Netzkabel aus den Netzsteckdosen
herausgezogen wurden.
2
1
Hinweis 10
212
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
ACHTUNG:
Keine Gegenstände, die mehr als 82 kg wiegen, auf Rack-Einheiten ablegen.
Importante:
Tutti gli avvisi di attenzione e di pericolo riportati nella pubblicazione
:cit.Netfinity Server Library:ecit. iniziano con un numero. Questo numero
viene utilizzato per confrontare avvisi di attenzione o di pericolo in inglese
con le versioni tradotte riportate in questa sezione.
Ad esempio, se un avviso di attenzione inizia con il numero 1, la relativa
versione tradotta è presente in questa sezione con la stessa numerazione.
Prima di eseguire una qualsiasi istruzione, accertarsi di leggere tutti gli avvisi
di attenzione e di pericolo.
Avviso 1
PERICOLO
La corrente elettrica circolante nei cavi di alimentazione, del telefono e di
segnale è pericolosa.
Per evitare il pericolo di scosse elettriche:
v Non collegare o scollegare i cavi, non effettuare l’installazione, la
manutenzione o la riconfigurazione di questo prodotto durante i temporali.
v Collegare tutti i cavi di alimentazione ad una presa elettrica correttamente
cablata e munita di terra di sicurezza.
v Collegare qualsiasi apparecchiatura collegata a questo prodotto ad una
presa elettrica correttamente cablata e munita di terra di sicurezza.
Chapter 4. Related Service Information
213
v Quando possibile, collegare o scollegare i cavi di segnale con una sola
mano.
v Non accendere qualsiasi apparecchiatura in presenza di fuoco, acqua o se
sono presenti danni all’apparecchiatura stessa.
v Scollegare i cavi di alimentazione, i sistemi di telecomunicazioni, le reti e i
modem prima di aprire i coperchi delle unità, se non diversamente indicato
nelle procedure di installazione e configurazione.
v Collegare e scollegare i cavi come descritto nella seguente tabella quando si
effettuano l’installazione, la rimozione o l’apertura dei coperchi di questo
prodotto o delle unità collegate.
Per collegare:
Per scollegare:
1. SPEGNERE tutti i dispositivi.
1. SPEGNERE tutti i dispositivi.
2. Collegare prima tutti i cavi alle unità.
2. Rimuovere prima i cavi di alimentazione dalle
prese elettriche.
3. Collegare i cavi di segnale ai connettori.
4. Collegare i cavi di alimentazione alle prese
elettriche.
3. Rimuovere i cavi di segnale dai connettori.
4. Rimuovere tutti i cavi dalle unità.
5. ACCENDERE le unità.
Avviso 2
214
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
ATTENZIONE:
Quando si sostituisce la batteria al litio, utilizzare solo una batteria IBM con
numero parte 33F8354 o batterie dello stesso tipo o :erev refid=a. di tipo
equivalente consigliate dal produttore. Se il sistema di cui si dispone è
provvisto di un modulo contenente una batteria al litio, sostituire tale batteria
solo con un tipo di modulo uguale a quello fornito dal produttore. La batteria
contiene litio e può esplodere se utilizzata, maneggiata o smaltita
impropriamente.
Evitare di:
v Gettarla o immergerla in acqua
v Riscaldarla ad una temperatura superiore ai 100C
v Cercare di ripararla o smontarla
Smaltire secondo la normativa in vigore (D.Lgs 22 del 5/2/9) e successive
disposizioni nazionali e locali.
Avviso 3
Chapter 4. Related Service Information
215
ATTENZIONE:
Quando si installano prodotti laser come, ad esempio, le unità DVD,
CD-ROM, a fibre ottiche o trasmettitori, prestare attenzione a quanto segue:
v Non rimuovere i coperchi. L’apertura dei coperchi di prodotti laser può
determinare l’esposizione a radiazioni laser pericolose. All’interno delle
unità non vi sono parti su cui effettuare l’assistenza tecnica.
v L’utilizzo di controlli, regolazioni o l’esecuzione di procedure non descritti
nel presente manuale possono provocare l’esposizione a radiazioni
pericolose.
216
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
PERICOLO
Alcuni prodotti laser contengono all’interno un diodo laser di Classe 3A o
Classe 3B. Prestare attenzione a quanto segue:
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non
guardarlo direttamente con strumenti ottici ed evitare l’esposizione diretta al
fascio.
Avviso 4
Chapter 4. Related Service Information
217
ATTENZIONE:
Durante il sollevamento della macchina seguire delle norme di sicurezza.
Avviso 5
ATTENZIONE:
Il pulsante del controllo dell’alimentazione situato sull’unità e l’interruttore di
alimentazione posto sull’alimentatore :erev refid=a. non disattiva la corrente
elettrica fornita all’unità. L’unità potrebbe disporre di più di un cavo di
alimentazione. Per disattivare la corrente elettrica dall’unità, accertarsi che
tutti i cavi di alimentazione siano scollegati dalla sorgente di alimentazione.
2
1
Avviso 10
218
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
ATTENZIONE:
Non poggiare oggetti che pesano più di 82 kg sulla parte superiore delle unità
montate in rack.
Chapter 4. Related Service Information
219
220
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Chapter 4. Related Service Information
221
Importante:
Todas las declaraciones de precauciín de esta :cit.Biblioteca del servidor
Netfinity:ecit. empiezan con un número. Dicho número se emplea para
establecer una referencia cruzada de una declaraciín de precauciín o peligro
en inglés con las versiones traducidas que de dichas declaraciones pueden
encontrarse en esta secciín.
Por ejemplo, si una declaraciín de peligro empieza con el número 1, las
traducciones de esta declaraciín de precauciín aparecen en esta secciín bajo
Declaraciín 1.
Lea atentamente todas las declaraciones de precauciín y peligro antes de
llevar a cabo cualquier operaciín.
Declaración 1
222
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
PELIGRO:
La corriente eléctrica de los cables telefínicos, de alimentaciín y de
comunicaciones es perjudicial.
Para evitar una descarga eléctrica:
v No conecte ni desconecte ningún cable ni realice las operaciones de
instalaciín, mantenimiento o reconfiguraciín de este producto durante una
tormenta.
v Conecte cada cable de alimentaciín a una toma de alimentaciín eléctrica con
conexiín a tierra y cableado correctos.
v Conecte a tomas de alimentaciín con un cableado correcto cualquier equipo
que vaya a estar conectado a este producto.
v Si es posible, utilice una sola mano cuando conecte o desconecte los cables
de sent.al.
v No encienda nunca un equipo cuando haya riesgos de incendio, de
inundaciín o de daños estructurales.
v Desconecte los cables de alimentaciín, sistemas de telecomunicaciones, redes
y mídems conectados antes de abrir las cubiertas del dispositivo a menos
que se indique lo contrario en los procedimientos de instalaciín y
configuraciín.
v Conecte y desconecte los cables tal como se describe en la tabla siguiente
cuando desee realizar una operaciín de instalaciín, de traslado o de
apertura de las cubiertas para este producto o para los dispositivos
conectados.
Para la conexin
Para la desconexiín
1. APÁGUELO todo.
1. APÁGUELO todo.
2. En primer lugar, conecte los cables a los
dispositivos.
2. En primer lugar, retire cada cable de
alimentaciín de la toma de alimentaciín.
3. Conecte los cables de señal a los conectores.
3. Retire los cables de señal de los conectores.
4. Conecte cada cable de alimentaciín a la toma
de alimentaciín.
4. Retire los cables de los dispositivos.
5. ENCIENDA el dispositivo.
Chapter 4. Related Service Information
223
Declaración 2
PRECAUCIÓN:
Cuando desee sustituir la batería de litio, utilice únicamente el número de
pieza 33F8354 de IBM o cualquier tipo de batería equivalente que recomiende
el fabricante. Si el sistema tiene un mídulo que contiene una batería de litio,
sustitúyalo únicamente por el mismo tipo de mídulo, que ha de estar creado
por el mismo fabricante. La batería contiene litio y puede explotar si el
usuario no la utiliza ni la maneja de forma adecuada o si no se desprende de
la misma como corresponde.
No realice las acciones siguientes:
v Arrojarla al agua o sumergirla
v Calentarla a una temperatura que supere los 100C (212F)
v Repararla o desmontarla
Despréndase de la batería siguiendo los requisitos que exija el reglamento o la
legislaciín local.
Declaración 3
PRECAUCIÓN:
Cuando instale productos láser (como, por ejemplo, CD-ROM, unidades DVD,
dispositivos de fibra íptica o transmisores), tenga en cuenta las advertencias
siguientes:
v No retire las cubiertas. Si retira las cubiertas del producto láser, puede
quedar expuesto a radiaciín láser perjudicial. Dentro del dispositivo no
existe ninguna pieza que requiera mantenimiento.
v El uso de controles o ajustes o la realizaciín de procedimientos que no sean
los que se han especificado aquí pueden dar como resultado una exposiciín
perjudicial a las radiaciones.
PELIGRO:
224
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Algunos productos láser contienen un diodo de láser incorporado de Clase 3A
o de Clase 3B. Tenga en cuenta la advertencia siguiente.
Cuando se abre, hay radiaciín láser. No mire fijamente el rayo ni lleve a cabo
ningún examen directamente con instrumentos ípticos; evite la exposiciín
directa al rayo.
Declaración 4
≥ 32 kg (70.5 lbs)
≥ 55 kg (121.2 lbs)
PRECAUCIÓN:
Tome medidas de seguridad al levantar el producto.
Declaración 5
PRECAUCIÓN:
El botín de control de alimentaciín del dispositivo y el interruptor de
alimentaciín de la fuente de alimentaciín no apagan :erev refid=a. la corriente
eléctrica suministrada al dispositivo. Es posible también que el dispositivo
tenga más de un cable de alimentaciín. Para eliminar la corriente eléctrica del
dispositivo, asegúrese de desconectar todos los cables de alimentaciín de la
Chapter 4. Related Service Information
225
fuente de alimentaciín.
2
1
Declaración 10
PRECAUCIÓN:
No coloque ningún objeto que pese más de 82 kg (180 libras) encima de los
dispositivos montados en bastidor.
226
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Send us your comments!
We want to know your opinion about this manual (part number 06P1504).
Your input will help us to improve our publications.
Please photocopy this survey, complete it, and then fax it to IBM HMM
Survey at 919-543-8167 (USA).
Name: _________________________________________
Phone number: __________________________________
1.
Do you like this manual?
h Yes h No
_________________________________________
_________________________________________
2.
What would you like to see added, changed, or deleted in this manual?
_________________________________________
_________________________________________
3.
What is your service experience level?
h Less than five years
4.
h More than five years
Which Servers do you service most?
_________________________________________
_________________________________________
_________________________________________
_________________________________________
Thank you for your response!
Problem determination tips
Due to the variety of hardware and software combinations that can be
encountered, use the following information to assist you in problem
determination. If possible, have this information available when requesting
assistance from Service Support and Engineering functions.
v Machine type and model
v Processor or hard disk upgrades
Chapter 4. Related Service Information
227
v Failure symptom
– Do diagnostics fail?
– What, when, where, single, or multiple systems?
– Is the failure repeatable?
– Has this configuration ever worked?
– If it has been working, what changes were made prior to it failing?
– Is this the original reported failure?
v Reference/Diagnostics version
– Type and version level
v Hardware configuration
– Print (print screen) configuration currently in use
– BIOS level
v Operating system software
– Type and version level
Note: To eliminate confusion, identical systems are considered identical only
if they:
1. Are the exact machine type and models
2. Have the same BIOS level
3. Have the same adapters/attachments in the same locations
4. Have the same address jumpers/terminators/cabling
5. Have the same software versions and levels
6. Have the same Reference/Diagnostics Diskette (version)
7. Have the same configuration options set in the system
8. Have the same setup for the operation system control files
Comparing the configuration and software set-up between ″working
and non-working″ systems will often lead to problem resolution.
Notices
References in this publication to IBM products, programs, or services do not
imply that IBM intends to make these available in all countries in which IBM
operates. Any reference to an IBM product, program, or service is not
intended to state or imply that only that IBM product, program, or service
may be used. Subject to IBM’s valid intellectual property or other legally
protectable rights, any functionally equivalent product, program, or service
may be used instead of the IBM product, program, or service. The evaluation
and verification of operation in conjunction with other products, except those
expressly designated by IBM, are the responsibility of the user.
228
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Trademarks
The following items are trademarks of the IBM Corporation in the United
States or other countries or both:
HelpCenter
IBM
NetBAY3
Netfinity Manager
SystemXtra
HelpFax
OS/2
Netfinity
ThinkPad
The following terms are trademarks of other companies:
Notes
Lotus Development Corporation
MMX and Pentium are trademarks or registered trademarks of Intel
Corporation.
UNIX is a trademark or registered trademark of The Open Group in the
United States and other countries.
Windows NT is a trademark or registered trademark of Microsoft
Corporation.
Miscellaneous Information
Acronyms, Abbreviations, and Terms
Term
ACPA/A
ADP
AGP
Alt
ANSI
ARTIC
ASCII
AT
AVC
BIOS
bps
BPS
CCITT
CCS
CCSB
CCSB
Information
Audio Capture and Playback Adapter
Automatic Data Processing
Advanced Graphics Port
Alternate
American National Standards Institute
A Real Time Interface Coprocessor
American National Standard Code for Interface Interchange
Advanced Technology (refer to AT Bus)
Audio Video Connection
Basic Input/Output System
Bits Per Second
Bytes Per Second
The International Telephone and Telegraph Consultative Committee
Common Command Set
Common Complete Status Block
Configuration Control Sub Board
Chapter 4. Related Service Information
229
Term
CD
CDPD
CD-ROM
CGA
CRC
CRT
CSA
CSD
DASD
DMA
DRAM
ECA
ECC
EGA
ESD
ESDI
EEPROM
EWS
FRU
GPIB
GSA
Ht
IDE
IC
IEEE
IEC
IML
IPL
ISA
ISO
ISDN
LAN
LBA
LTB
LUN
MAP
MCGA
MCA
MHz
MIDI
MM
N/A
NDD
NDIS
230
6649
Information
Compact Disc
Cellular Digital Packet Data
CD Read-Only Memory
Color Graphics Adapter (See EGA)
Cyclic Redundancy Check
Cathode Ray Tube
Canadian Standards Association
Corrective Service Diskette
Direct Access Storage Device (hard disk)
Direct Memory Access
Dynamic Random Access Memory
Engineering Change Announcement
Error Correction Code
Enhanced Graphics Adapter
Electrostatic Discharge
Enhanced Small Device Interface
Electrically Erasable Programmable Read-Only Memory
Energy Work Station
Field Replaceable Unit (replaceable part)
General Purpose Interface Bus (IEEE 348)
General Services Administration
Height
Integrated Drive Electronics
Integrated Circuit
Institute of Electrical and Electronics Engineers
International Electrotechnical Commission
Initial Machine Load
Initial Program Load
Industry Standard Architecture
International Organization for Standardization
Integrated-Services Digital Network
Local Area Network
Local Block Address
Local Transfer Bus
Logical Unit Number (refer to SCSI)
Maintenance Analysis Procedure
Modified Color Graphics Adapter
Micro Channel Architecture (bus structure)
Mega Hertz (million cycles per second)
Musical Instrument Digital Interface
Multimedia
Not Available or Not Applicable
National Distribution Division
Network Driver Interface Specification
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Term
NMI
NSC
NVRAM
OEM
PCI
PCMCIA
POS
PUN
RAID
RAM
RGB
RIPL
ROM
SASD
SCB
SCSI
SCSI ID
SPD
SR
SRAM
SVGA
STN
T/A
TDD
TFT
TPF
TSR
UL
VCA
VESA
VGA
VPD
VRAM
WORM
XGA
Y/C
Information
Non-Maskable Interrupt
National Support Center
Non-Volatile Random Access Memory
Original Equipment Manufacturer
Peripheral Component Interconnect
Personal Computer Memory Card International Association
Programmable Option Select
Physical Unit Number (refer to SCSI)
Redundant Array of Independent Disks
Random Access Memory (read/write)
Red Green Blue (refer to monitors)
Remote Initial Program Load
Read-Only Memory
Sequential Access Storage Device (Tape)
Subsystem Control Block
Small Computer Systems Interface
SCSI Identification Number
Software Product Description
Service Representative
Static Random Access Memory
Super Video Graphics Array (800x600x16)
Super Twisted Nematic
NDD Technical Advisor (see your Marketing Representative)
Telecommunications Device for the Deaf
Thin-Film Transistor
ThinkPad File
Terminate and Stay Resident
Underwriters Laboratory
Video Capture Adapter
Video Electronics Standards Association
Video Graphics Array (640x480x16)
Vital Product Data
Video Random Access Memory
Write Once Read Many (storage medium)
Extended Graphics Array
Luminance/Chrominance Signal (Video)
Chapter 4. Related Service Information
231
232
6649
Hardware Maintenance Manual: IBM NetVista Computer Types 6058, 6059, 6269, 6568, 6569, 6578, 6579, 6648,
Part Number: 06P1504
(1P) P/N: 06P1504
Download PDF

advertising