Operating instructions | Bushnell 91-0330/03-02 Digital Camera User Manual

System Component
Operating Instructions
Model No.
SC-HD510
SC-HD310
The illustrations show SC-HD510 for areas except Australia and N.Z.
Note:
The “EB” indication shown on the outside packing
case indicates United Kingdom.
Before connecting, operating or adjusting this
product, please read these instructions completely.
Please keep this manual for future reference.
EB EP GN
RQT5296-B
Dear Customer
Thank you for purchasing this product.
For optimum performance and safety, please read these
instructions carefully.
Before use
These operating instructions are applicable to the following
systems.
These operating instructions, however, fundamentally explain the
operation of system SC-HD510.
System
SC-HD510
SC-HD310
Amplifier
SE-HD510
SE-HD310
Tuner
ST-HD510
ST-HD310
CD player
SL-HD510
SL-HD310
Cassette deck
RS-HDA710
RS-HD310
Speakers
SB-HD510
SB-HD310
Supplied accessories
Please check and identify the supplied
accessories.
AC mains lead.............................................................1 pc.
For United Kingdom
For Australia and N.Z.
(RJA0053-2X)
(RJA0035-K)
For others
(RJA0019-X)
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
Remote control ...........................................................1 pc.
For Australia and N.Z.
For others
(RAK-HDA26WH)
(RAK-HDA25WH)
CAUTION!
DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE,
BUILT IN CABINET OR IN ANOTHER CONFINED SPACE.
ENSURE THE UNIT IS WELL VENTILATED. ENSURE THAT
CURTAINS AND ANY OTHER MATERIALS DO NOT
OBSTRUCT THE VENTILATION TO PREVENT RISK OF
ELECTRIC SHOCK OR FIRE HAZARD DUE TO
OVERHEATING.
Remote control batteries .........................................2 pcs.
FM indoor antenna ....................................................1 pc.
For Australia and N.Z.
For others
(RSA0006)
(RSA0007)
CLASS 1
LASER PRODUCT
AM loop antenna set (RSA0022-J) ............................1 pc.
(Back of product)
Speaker cords
● Red and black (REE0499) .......................................2 pcs.
● Blue and gray (REE0853)
SC-HD510 only .............2 pcs.
(CD player)
Antenna plug adapter (SJP9009) ..............................1 pc.
(United Kingdom only)
DANGER
ADVARSEL
INVISIBLE LASER RADIATION WHEN OPEN.
AVOID DIRECT EXPOSURE TO BEAM.
USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE
ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING.
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA
NÄKYMÄTÖNTÄ LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
(Tuotteen sisällä)
VARNING
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN.
(Apparatens insida)
ADVARSEL
USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS
BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.
(Produktets innside)
UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET.
2
(Indersiden at apparatet)
VARO!
VORSICHT NICHT DEM STRAHL AUSSETZEN.
RQT5296
(Inside of product)
(Im Inneren des Gerätes)
Use numbers indicated in parentheses when asking for replacement
parts.
Table of contents
Safety precautions
Before use
Placement
Radio operations
The Radio: manual tuning .....................................................12
The Radio: preset tuning .......................................................13
Cassette deck operations
Cassette tapes ..........................................................................14
Compact disc operations
Set the unit up on an even surface away from direct sunlight, high
temperatures, high humidity, and excessive vibration. These
conditions can damage the cabinet and other components, thereby
shortening the unit’s service life.
Place it at least 15 cm away from wall surfaces to avoid distortion
and unwanted acoustical effects.
Do not place heavy items on the unit.
Before use
Safety precautions .....................................................................3
Caution for AC Mains Lead .....................................................4
The remote control ....................................................................5
Installation ....................................................................................5
Connections ................................................................................6
Front panel controls ..................................................................9
Turning the DEMO function off ............................................10
Setting the time ........................................................................11
Saving power in standby mode ...........................................11
Voltage
Do not use high voltage power sources. This can overload the
unit and cause a fire.
Do not use a DC power source. Check the source carefully when
setting the unit up on a ship or other place where DC is used.
AC mains lead protection
Ensure the AC mains lead is connected correctly and not
damaged. Poor connection and lead damage can cause fire or
electric shock. Do not pull, bend, or place heavy items on the lead.
Grasp the plug firmly when unplugging the lead. Pulling the AC
mains lead can cause electric shock.
Do not handle the plug with wet hands. This can cause electric
shock.
CDs
Normal play .................................................................................16
Other modes of play ....................................................................17
Recording operations
Before recording ......................................................................19
Preparatory steps ........................................................................19
Recording the radio.................................................................20
Recording CDs
Normal recording .........................................................................20
One touch CD editing (AI EDIT) ..................................................21
Timer operations
Using the timers
The play timer..............................................................................22
The record timer ..........................................................................23
The play and record timers..........................................................24
The sleep timer............................................................................24
Using the timers together ............................................................24
Foreign matter
Do not let metal objects fall inside the unit. This can cause
electric shock or malfunction.
Do not let liquids get into the unit. This can cause electric shock
or malfunction. If this occurs, immediately disconnect the unit from
the power supply and contact your dealer.
Do not spray insecticides onto or into the unit. They contain
flammable gases which can ignite if sprayed into the unit.
Service
Do not attempt to repair this unit by yourself. If sound is
interrupted, indicators fail to light, smoke appears, or any other
problem that is not covered in these operating instructions occurs,
disconnect the AC mains lead and contact your dealer or an
authorized service center. Electric shock or damage to the unit can
occur if the unit is repaired, disassembled or reconstructed by
unqualified persons.
Extend operating life by disconnecting the unit from the power
source if it is not to be used for a long time.
Reference
Using other equipment ...........................................................25
Convenient functions .............................................................26
Maintenance ..............................................................................26
Troubleshooting guide ...........................................................27
Technical specifications .......................................Back cover
3
RQT5296
Caution for AC Mains Lead
(“EB” area code model only)
WARNING: DO NOT CONNECT EITHER WIRE TO
THE EARTH TERMINAL WHICH IS MARKED WITH
THE LETTER E, BY THE EARTH SYMBOL
OR
COLOURED GREEN OR GREEN/YELLOW.
For your safety, please read the following text carefully.
THIS PLUG IS NOT WATERPROOF–KEEP DRY.
Before use
(For United Kingdom)
This appliance is supplied with a moulded three pin
mains plug for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that
the replacement fuse has a rating of 5-ampere and that it
is approved by ASTA or BSI to BS1362.
Check for the ASTA mark
or the BSI mark
on the
body of the fuse.
If the plug contains a removable fuse cover you must
ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until
a replacement cover is obtained.
A replacement fuse cover can be purchased from your
local dealer.
Before use
Remove the connector cover.
How to replace the fuse
The location of the fuse differ according to the type of
AC mains plug (figures A and B). Confirm the AC
mains plug fitted and follow the instructions below.
Illustrations may differ from actual AC mains plug.
1. Open the fuse cover with a screwdriver.
Figure A
CAUTION!
IF THE FITTED MOULDED PLUG IS UNSUITABLE
FOR THE SOCKET OUTLET IN YOUR HOME THEN
THE FUSE SHOULD BE REMOVED AND THE PLUG
CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL
SHOCK IF THE CUT OFF PLUG IS INSERTED INTO
ANY 13-AMPERE SOCKET.
If a new plug is to be fitted please observe the wiring
code as stated below.
If in any doubt please consult a qualified electrician.
Figure B
Fuse cover
IMPORTANT
The wires in this mains lead are coloured in accordance
with the following code:
Blue: Neutral, Brown: Live.
As these colours may not correspond with the coloured
markings identifying the terminals in your plug, proceed
as follows:
The wire which is coloured Blue must be connected to
the terminal which is marked with the letter N or coloured
Black or Blue.
The wire which is coloured Brown must be connected to
the terminal which is marked with the letter L or coloured
Brown or Red.
2. Replace the fuse and close or attach the fuse
cover.
Figure A
Fuse
(5 ampere)
Figure B
Fuse
(5 ampere)
4
RQT5296
The remote control
A
A
+
−
+
R6/LR6
(AA, UM-3)
2
−
Insert so the poles (+ and –) match those in the remote control.
Do not use rechargeable type batteries.
Do not;
● mix old and new batteries.
● use different types at the same time.
● heat or expose to flame.
● take apart.
● short circuit.
● attempt to recharge alkaline or manganese batteries.
Mishandling of batteries can cause electrolyte leakage which can
damage items the fluid contacts and may cause a fire.
If electrolyte leaks from the batteries, consult your dealer.
Wash thoroughly with water if electrolyte comes in contact with any
part of your body.
Before use
1
Batteries
Remove if the remote control is not going to be used for a long
period of time. Store in a cool, dark place.
Replace if the unit does not respond to the remote control even
when held close to the front panel.
If the battery lid comes loose, slide it back into place horizontally.
B
B
30˚
30˚
7m
Aim at the sensor, avoiding obstacles, at a maximum range of 7
meters directly in front of the unit.
● Keep the transmission window and the unit’s sensor free from
dust.
● Operation can be affected by strong light sources, such as direct
sunlight, and the glass doors on cabinets.
Do not;
● put heavy objects on the remote control.
● take the remote control apart.
● spill liquids onto the remote control.
C
C
aSL-HD510
/310
Use
bST-HD510
/310
cRS-HDA710/
fSB-HD510/310
RS-HD310
eSB-HD510/310
dSE-HD510/310
Installation
a CD player
b Tuner
c Cassette deck
d Amplifier
e Left speaker
f Right speaker
Note
●
These speakers do not have magnetic shielding. Do not place
them near televisions, personal computers or other devices easily
influenced by magnetism.
●
SC-HD310 only
Left and right speakers are exactly the same.
Caution
Use the speakers only with the
recommended system. Failure to do so can
damage the amplifier and speakers, and can
cause fire. Consult a qualified service person
if damage occurs or if a sudden change in
performance is apparent.
● Do not attach these speakers to walls or
ceilings.
●
5
RQT5296
Connections
Unless otherwise marked, the illustrations show SC-HD510
sold outside Australia and New Zealand.
2
3
Before use
Adhesive tape
1
1
c
(Left)
4
4
(Right)
5
To household
mains socket
3
A
c
a
b
1
4
To connect cables
Speaker
SC-HD510
Blue (–)
Amplifier
SC-HD510
HIGH
Gray (+)
White line
LOW
LOW
Blue (–)
Red (+)
To unplug cables
Hold the connector from
both ends and pull it out.
2
(For Australia and N.Z.)
Black (–)
Black (–)
Red (+)
SC-HD310
SC-HD310
FM ANT
75Ω
Red (+)
Black (–)
(For others)
FM ANT
75Ω
6
RQT5296
HIGH
Gray (+)
Red (+)
Black (–)
Basic connections for supplied
accessories
A
Before connection
Do not connect the AC mains lead until all other connections
are complete.
● To prepare the AM loop antenna, FM antenna (for Australia
and N.Z.) and speaker cables, twist the vinyl tip and pull off
(a).
● Disconnect the flat cable on the cassette deck (b).
1
Before use
●
Flat cables.
Keep the cables as flat as possible against the back of the
unit.
2
FM antenna.
Fix the other end of the antenna where reception is best.
3
AM loop antenna.
Keep loose antenna cord away from other wires and cords.
4
Speaker cables.
Connect the cables to the terminals of the same color. Never
allow the exposed wires to contact each other when
connected.
Use only the supplied speakers.
The combination of the system and the front speakers
provides the best sound. Using other speakers can damage
the unit and sound quality will be negatively affected.
(United Kingdom only)
BE SURE TO READ THE CAUTION FOR THE AC
MAINS LEAD ON PAGE 4 BEFORE PROCEEDING
TO STEP 5.
5
Connect the AC mains lead.
Insertion of connector
Even when the connector is perfectly inserted, depending on
the type of inlet used, the front part of the connector may jut
out as shown in the drawing.
However there is no problem using the unit.
Connector
Approx. 6 mm
Appliance inlet
For your reference
Information you enter into the unit’s memory, except for time,
remains intact for up to two weeks after the mains lead is
disconnected.
Note
The included AC mains lead is for use with this unit only. Do not use
it with other equipment.
7
RQT5296
Connections
A
A
(R)
Tuner
(L)
●
●
EXT/ OUT
IN
MD
a
Before use
(R)
DIGITAL
OPTICAL
OUT
(R)
(L)
(L)
CD player
IN
OUT
(L)
Connect DVD players to the EXT/MD IN terminal on the tuner.
DIGITAL
OPTICAL
IN
FM outdoor antenna
Turn off the power to all units before making connections.
Refer to the manual of the other unit for details.
(Cables and equipment not included.)
To listen to other equipment and make recordings
Connect other equipment to the EXT/MD IN terminals to output
sound through this unit's speakers or to record onto the cassette
deck. Connect this unit to other equipment through the EXT/MD
OUT terminals to record onto another recording device or output
from this unit through the other unit.
(R)
B
MD deck, etc.
(Recommended MD
deck: SJ-HDA710)
Tuner
Stereo phono cable (not included)
White (L)
Red (R)
To make digital recordings (a):
Remove the dust cap before use.
Use an optical fiber cable to connect other digital recording
equipment to DIGITAL OPTICAL OUT on the back of the CD player.
This connection enables you to make digital recordings.
A
Optional antenna connections
75 Ω coaxial
cable
(not included)
(For Australia and N.Z.)
A
,,
,,
(For others)
A
Use outdoor antennas if radio reception is poor.
B
,,,
,,,
,,,
,,,
,,,
(United Kingdom
only)
AM outdoor antenna
5-12 m
8
Note
●
●
Disconnect the FM indoor antenna.
The antenna should be installed by a competent technician.
C
AM outdoor antenna
15 mm
C
RQT5296
FM outdoor antenna
30 mm
Use the antenna
plug adapter
(included)
Tuner
External unit connections
Run a piece of vinyl wire horizontally across a window or other
convenient location.
Note
●
●
Leave the loop antenna connected.
Disconnect the antenna when the unit is not in use. Do not use
the antenna during an electrical storm.
Front panel controls
C
B
A
A
1
2
q
w
e
r
t
y
u
i
o
OPEN/CLOSE
CD TEXT
SCROLL
Disc tray
Disc tray open/close button (
OPEN/CLOSE)..................16
CD TEXT button (CD TEXT) ...................................................16
Scroll button (SCROLL) .........................................................16
AI edit button (AI EDIT) ..........................................................21
Skip/search buttons (
/
,
/
) ........................16
Stop button (■) ......................................................................16
Pause button ( )...................................................................16
Play button and indicator (u)................................................16
The color of the indicator depends on the operation taking place.
If stopped: orange
If playing: green
AI EDIT
B
3
4
5
6
7
8
9
B
10
11
OPEN/CLOSE
COUNTER
RESET
DOLBY NR
REV MODE
CD player
Before use
A
REC PAUSE
TPS SKIP
!0
!1
!2
!3
!4
!5
!6
!7
!8
!9
Cassette holder
Cassette tray open/close button (
OPEN/CLOSE) ..........14
Counter button (COUNTER)...................................................19
Dolby noise reduction button (DOLBY NR)..........................14
Counter reset button (RESET) ...............................................14
Reverse mode select button (REV MODE) ...........................14
Tape Program Sensor button (TPS SKIP) ............................15
Fast forward/rewind buttons (
[TPS]
) ....................15
Record pause button and indicator (● REC PAUSE) .........20
Playback buttons and indicators (v, u) ..............................14
The color of the indicator depends on the operation taking place.
If stopped, fast forwarding or rewinding: orange
If playing, recording, or carrying out TPS: green
@0 Stop button (■) ......................................................................14
[TPS]
C
12 13 14 15 16
Cassette deck
Tuner
@1 Display panel
The display also shows information for the cassette deck, CD
player, and amplifier.
@2 Play timer/record timer button and indicator
(
PLAY/
REC) .....................................................22, 23, 24
@3 Clock/timer, demo button
(CLOCK/TIMER, –DEMO)............................................10, 11, 22
@4 Set button (SET)......................................................................11
@5 Tuning/time adjust buttons
(TUNE/TIME ADJUST ∨, ∧) .............................................11,12
@6 Tuning mode button (TUNE MODE) ......................................12
17 18 19 20
C
21
SC-HD510 for areas except Australia and N.Z.
@7 RDS button (RDS) ...................................................................12
@8 Band select button (FM/AM) ..................................................12
PLAY/
REC CLOCK/TIMER
SET
TUNE/TIME ADJUST
TUNE MODE
RDS
– DEMO
22
23 24
25
FM/AM
SC-HD310 SC-HD510 for Australia and N.Z.
@7 FM band select button (FM) ...................................................12
@8 AM band select button (AM) ..................................................12
26 27 28
9
RQT5296
Front panel controls
C
A
A
A
29
30 31 32 33
Before use
/I
34 35
BLFS
VOLUME
MODE
36
INPUT SELECTOR
– DVD DIRECT
FINE TWEETER CONTROL
PHONES
DOWN
UP
MIN
MAX
37
SLEEP
PLAY
1
2
3
4
5
6
7
8
9
REC
@9 Standby indicator
When the unit is connected to the AC mains supply, this
indicator lights up in standby mode and goes out when the unit
is turned on.
#0 Standby/on switch ( /I) ........................................................11
Press to switch the unit from on to standby mode or vice versa.
In standby mode, the unit is still consuming a small amount of
power.
#1 ECO mode button (MODE) .....................................................11
#2 Headphone jack (PHONES)....................................................25
#3 Volume control (VOLUME) .....................................................12
SC-HD510 only
#4 Bass button (BLFS) ................................................................26
#5 Input selector (INPUT SELECTOR
) .................................25
#6 Input selector (INPUT SELECTOR
, -DVD DIRECT) ........25
#7 Fine tweeter control (FINE TWEETER CONTROL)...............26
SC-HD310 only
#4 Bass button (BASS)................................................................26
#5 Treble button (TREBLE) .........................................................26
#6 Input selector (INPUT SELECTOR) .......................................25
B
38
30
Amplifier
45
46
> 10
39
40
0
PROGRAM
CANCEL
RANDOM
REPEAT
B
47
Buttons #0 and #3 function in the same way as the controls on
the main unit.
48
41
a
#8
#9
$0
$1
$2
AUTO/
MONO
MD
CD
42
43
TAPE
EXT/MD
TUNER
TUNE
MUTING
TUNE
49
50
VOLUME
44
33
$3
B
a
A
C
MD
Remote control
D
$4
$5
$6
$7
$8
$9
%0
Sleep timer button (SLEEP) ...................................................24
Numbered buttons ..................................................................13
Program button (PROGRAM).................................................18
Random button (RANDOM)....................................................17
Input select buttons
(CD, TAPE, EXT/MD, TUNER)...............................12, 15, 17, 25
Basic operating buttons
Function changes according to the source.
Muting button (MUTING) ........................................................26
Play timer button (
PLAY) .................................................22
Record timer button (
REC) ..............................................23
Cancel button (CANCEL) .......................................................18
Repeat button (REPEAT)........................................................17
FM mode button (AUTO/MONO) ............................................12
Tuning buttons (TUNE ∧, TUNE ∨) .....................................12
For areas except Australia and N.Z.
C
CLOCK/TIMER, –DEMO
MD deck operations (when connected to MD deck SJ-HDA710
(sold separately)) a
A Stop button (■)
B Pause button ( )
C Play button (s)
D Skip/search buttons (
/
,
/
)
C
CLOCK/TIMER
– DEMO
Turning the DEMO function off
If the clock has not been set, a demonstration of the display is
shown when the unit is off.
This function is set to on at the time of purchase.
To get the most from ECO mode (a page 11), turn this function off.
Press and hold [CLOCK/TIMER, –DEMO] until
“NO DEMO” is displayed.
Each time you press and hold the button:
DEMO MODE (on)
NO DEMO (off)
10
RQT5296
A
A
This is a 24-hour clock.
The example shows how to set the clock for Wednesday 16:25
(4:25 pm).
1
2
Press [
/I] to turn the unit on.
q Press [CLOCK/TIMER, –DEMO] to
display “CLOCK.”
Each time you press the button:
CLOCK
2
1
2
3, 4
REC
Original display
w Within 7 seconds
Press [SET].
/I
1
CLOCK/TIMER
3
q Press [TUNE/TIME ADJUST
(∨ or ∧)] to set the day.
w Press [SET].
4
q Press [TUNE/TIME ADJUST
(∨ or ∧)] to set the time.
w Press [SET].
– DEMO
2
3
PLAY
Before use
1
Setting the time
1
The time is set and the original display is restored.
Displaying the clock
Press [CLOCK/TIMER, –DEMO].
The clock is shown for about 5 seconds.
SET
TUNE/TIME ADJUST
Saving power in standby mode
When this mode is turned on, the clock is not displayed when the
unit is in standby mode, thereby reducing standby mode power
consumption from 9 W to 0.8 W. The standby indicator still lights.
SET
2
B
Note
Turn DEMO off. ECO does not work when DEMO is on.
4
Turning ECO on and off:
1
TUNE/TIME ADJUST
q Press [ /I] to turn the unit on.
w Press [MODE].
The current mode is displayed. Press again to change the mode.
Each time you press the button:
NORMAL (off)
ECO (on)
SET
2
The mode can be switched to ECO when the unit is off but it can
not be switched back to NORMAL.
B
1
/I
2 MODE
11
RQT5296
The Radio: manual tuning
/I
4
SC-HD310 SC-HD510 for Australia and N.Z.
1
Radio stations can be tuned manually by selecting the station’s
frequency or they can be preset into channels to make it easy to
tune with the remote control (a page 13).
Preparation: Turn the unit on.
1
SC-HD310
SC-HD510 for Australia and N.Z.
Press [FM] or [AM] to select the band.
SC-HD510 for others
Press [FM/AM] to select the band.
Each time you press the button:
FM
AM
Radio operations
2
3
1
RDS
2
FM
Each time you press the button:
MANUAL
PRESET
1 SC-HD510 for others
SC-HD310 SC-HD510 for Australia and N.Z.
Press [TUNE MODE] to select “MANUAL”.
3
AM
Press [TUNE/TIME ADJUST (∨ or ∧)]
to select the frequency of the required
station.
“TUNED” is displayed when a radio station is tuned.
“STEREO” is displayed when a stereo FM broadcast is being
received.
SC-HD510 for others
4
FM/AM
Adjust the volume.
On the remote control
1. Press [TUNER] to select the band.
2. Press [TUNE ∧] or [TUNE ∨] to select the frequency.
Auto tuning
2
Press and hold [TUNE/TIME ADJUST (∨ or ∧)] for a moment until
the frequency starts changing rapidly. The unit begins auto tuning,
stopping when it finds a station.
TUNE MODE
RDS broadcasting
SC-HD510 for areas except Australia and N.Z.
3
TUNE/TIME ADJUST
TUNED STEREO
4
VOLUME
DOWN
A
UP
This unit can display the text data transmitted by the radio data
system (RDS) available in some areas.
Changing the display
Press [RDS].
Each time you press the button:
→PS display (the name of the station)
↓
PTY display (the type of program)
↓
RT display (various kinds of information, such as call-in
↓
numbers, weather, and news.)
Frequency display
Note
RDS displays may not be available if reception is poor.
A
RANDOM
REPEAT
AUTO/
MONO
MD
CD
TAPE
EXT/MD
AUTO/
MONO
TUNER
TUNE
MUTING
TUNE
VOLUME
One touch play
Remote control only
When the unit is off, press [TUNER].
The unit comes on and starts playing the radio with the volume fading in.
TUNER
A
If noise is excessive in FM
Remote control only
Press [AUTO/MONO] to display “MONO”.
Each time you press the button:
AUTO
MONO
This mode improves sound quality if reception is weak for some
reason but broadcasts are heard in monaural.
Press [AUTO/MONO] again to cancel the mode.
MONO is also canceled if the frequency is changed.
Leave the tuner in AUTO for normal listening. Stereo and monaural
broadcasts are automatically played as they are received.
12
RQT5296
The Radio: preset tuning
Choose either automatic presetting, which presets all the stations
the tuner can receive, or manual presetting, which allows you to
select the stations to preset and the order they are to be preset in.
There are 39 channels available for presetting.
A
TUNE/TIME ADJUST ∨, ∧
A
Automatic presetting
Do the following once each for FM and AM.
Preparation: Tune to the frequency presetting is to begin at.
(a page 12).
SET
TUNE MODE
SET
Release the button when “AUTO MEMORY” appears.
The tuner presets all the stations it can receive into the channels in
ascending order. FM stations are preset into channels 1 to 39, and
AM stations are preset into channels 21 to 39.
“SET OK” is shown when presetting is complete and the last station
to be preset is played.
“ERROR” is displayed if the tuner doesn’t receive any stations. Do
presetting manually if this happens (see below).
Note
Radio operations
Hold down [SET].
AM stations replace any FM channels that were preset in channels
21 to 39.
Preset channel
Manual presetting
PRESET TUNED
Preset the stations one at a time.
PRESET TUNED
q
w
e
r
B
SLEEP
PLAY
1
2
3
4
5
6
7
8
9
REC
> 10
0
PROGRAM
CANCEL
RANDOM
REPEAT
2
EXT/MD
TUNER
TUNE
MUTING
1
1
TUNE
VOLUME
1
Selecting channels
On the remote control
AUTO/
MONO
TAPE
The station occupying a channel is erased if another station is
preset in that channel.
B
MD
CD
Tune to the required station.
Press [SET].
Press [TUNE/TIME ADJUST (∨ or ∧)] to select a channel.
Press [SET].
Press [TUNER].
The unit automatically comes on.
2
Press the numbered buttons to select
the channel.
For channels 1 to 9 press the corresponding number.
For channels 10 or over press [≥10], then the two digits.
e.g. To select channel 21 [≥10] → [2] → [1]
TUNER
On the main unit
1. Press [TUNE MODE] to select “PRESET”.
2. Press [TUNE/TIME ADJUST (∨ or ∧)] to select the channel.
2
1
2
3
4
5
6
7
8
9
>10
0
Preset channel
PRESET TUNED
13
RQT5296
Cassette tapes
/I
5
Preparation: Turn the unit on.
1
1
RESET
2
4
Make sure the cassette is fully inserted and press
[
OPEN/CLOSE] to close the deck.
2
Press [DOLBY NR] to select Dolby NR
on (“ NR” appears) or off.
3
Press [REV MODE] to select the
reverse mode.
Every time the button is pressed:
: One side is played.
: Both sides are played.
: Both sides are played eight times each.
■
4
OPEN/CLOSE
v] or [u
u].
Press [v
Play begins and the indicator changes to green.
u: to play the forward side (facing up).
v: to play the reverse side (facing down).
5
Adjust the volume.
A
Cassette deck operations
1
3
Press [ OPEN/CLOSE], insert the
cassette with the tape facing in.
To stop the tape
Press [■].
2
DOLBY NR
A
Resetting the tape counter
Press [RESET].
NR
3
Cassette tape selection and care
REV MODE
The unit can correctly play the following types. It identifies the type
automatically.
NR
Normal position/TYPE 1
High position/TYPE 2
Metal position/TYPE 4
4
Tapes exceeding 100 minutes are thin and can break or get
caught in the mechanism.
● Tape slack can get caught up in the mechanism and should be
taken up before the tape is played.
● Endless tapes can get caught up in the deck’s moving parts if
used incorrectly. Use tapes appropriate to this unit’s auto-reverse
mechanism.
●
NR
5
✔
✔
✔
VOLUME
Dolby noise reduction
DOWN
UP
Dolby NR reduces “hissing” when playing tapes. It increases the
high frequency region when recording and then reduces it in
playback. Use the same system during playback and recording.
This unit has Dolby B NR which reduces noise to a third.
Prerecorded cassettes and equipment marked “
” use Dolby B
NR.
A
RESET
NR
Dolby noise reduction manufactured under license from Dolby
Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol
are trademarks of Dolby
Laboratories Licensing Corporation.
14
RQT5296
Cassette tapes
Fast-forwarding and rewinding
A
Press [
TPS] or [TPS
is stopped.
A
Tape direction
u
v
] while the tape
rewind
fast-forward
High-speed fast-forward/rewind
This cassette deck is designed to roughly double fastforward/rewind speed automatically.
When you fast-forward from the beginning of the tape or rewind
from the end of it, the tape runs at high speed.
When approaching the end of the tape, the deck automatically
drops to normal speed.
[TPS]
B
One touch play
B
AUTO/
MONO
CD
TAPE
EXT/MD
TAPE
TUNER
TUNE
MUTING
TUNE
VOLUME
Remote control only
When a cassette is loaded and the unit is off, press [TAPE].
The unit comes on and starts play in the direction last selected with
the volume fade in.
Tape program sensor (TPS)
C
TPS finds the beginning of a track and starts play from there. You
can skip up to nine tracks.
C
1
Press [TPS SKIP] to select the
number of tracks you want to skip.
2
Press [
TPS] or [TPS
the direction.
Tape direction
u
v
1
1
2
backward
Cassette deck operations
MD
] to select
forward
Pressing [
TPS] or [TPS
] during play takes you to
the beginning of the current track or the next track,
depending on tape direction.
TPS SKIP
To cancel
Press [■].
Note
●
2
●
[TPS]
Stop the tape before changing the TPS direction.
TPS may not operate correctly in the following situations:
If the interval between tracks is less than 4 seconds.
If there is noise between tracks.
If there are silent parts within tracks.
15
RQT5296
CDs
/I
Normal play
1
3
Preparation: Turn the unit on.
1
Press [
tray.
OPEN/CLOSE] to open the
Set a CD label up on the tray.
Press [
OPEN/CLOSE] to close the tray.
The number of tracks and playing time is displayed if “CD” is
selected as the source.
■
1
Total number
of tracks
OPEN/CLOSE
2
3
2
Total playing
time
u] to start play.
Press [u
Adjust the volume.
To stop the disc
Press [■].
To pause play
Press [ ] during play. Press [
Label must
face upward.
] or [u] to resume play.
Skipping tracks
Press [
/
] (backward), or [
/
Compact disc operations
Searching through tracks
During play
Press and hold [
/
] (backward), or [
2
Track number
Elapsed play
time
] (forward).
/
] (forward).
“NO DISC” is displayed
When the unit is in CD mode but a disc isn’t in the player.
Note
You cannot skip to tracks already played in random play.
(a page 17).
● Skipping is done in the selected order in program play.
(a page 18).
● You can search only within tracks in random and program play.
●
3
VOLUME
A
DOWN
CD text discs
UP
This unit reads and displays the information on these discs.
A
To switch between the text display and the normal display:
Press [CD TEXT].
Scrolling the text
Press [SCROLL].
“SCROLL ON” is shown and the information scrolls across the
display.
Press [SCROLL] again to cancel.
CD TEXT
B
SCROLL
Scroll does not work if the text is less than 12 letters.
a
B
CD selection and care
Choose discs with these marks: (a)
b
c
16
RQT5296
Do not;
● use irregularly shaped CDs (b).
● attach extra labels and stickers.
● use CDs with labels and stickers that are coming off or with
adhesive exuding from under labels and stickers (c).
● attach scratch-proof covers or any other kind of accessory.
● write anything on the CD.
● clean CDs with liquids (Wipe with a soft, dry cloth.).
CDs
A
SLEEP
1
1-9, 0, > 10
PLAY
2
Remote control only
When a CD is loaded and the unit is off, press [CD].
The unit comes on and starts play with the volume fading in.
3
> 10
4
5
6
7
8
9
One touch play
REC
0
PROGRAM
CANCEL
RANDOM
REPEAT
RANDOM
Other modes of play
REPEAT
Remote control only
AUTO/
MONO
MD
CD
CD
TAPE
EXT/MD
TUNE
MUTING
Preparation:
TUNER
s
Press [CD] to put the unit in CD mode.
TUNE
VOLUME
B
Direct access play:
Starts normal play from a selected track
Select the track with the numbered buttons.
For tracks numbered 10 and over, press [≥10] then the two digits.
A
CD
C
Random play:
Plays the tracks once each in random order
B
To cancel
Press [RANDOM].
“RANDOM” goes out.
1
2
3
4
5
6
7
8
9
>10
D
0
Repeat play:
Repeats all tracks or programmed tracks
Press [REPEAT] before or during play.
C
RANDOM
RANDOM
D
To cancel
Press [REPEAT].
“
” goes out.
Repeating selected tracks
1. Program the track(s) (a step 1 and 2, page 18).
2. Press [REPEAT] to display “
”.
3. Press [s].
Compact disc operations
Press [RANDOM].
REPEAT
17
RQT5296
CDs
Other modes of play
SLEEP
PLAY
Program play:
REC
Select up to 24 tracks to play in the order you choose
1
2
3
2
> 10
1
4
5
6
7
8
9
Remote control only
0
CANCEL
PROGRAM
CANCEL
RANDOM
REPEAT
Preparation:
Press [CD] to put the unit in CD mode.
1
2
AUTO/
MONO
MD
CD
TAPE
EXT/MD
TUNER
3
TUNE
MUTING
TUNE
Press [PROGRAM].
Enter the track number with the
numbered buttons.
For tracks numbered 10 and over, press [≥10] then the two
digits.
Repeat this step to program the tracks in the required order.
VOLUME
3
s].
Press [s
All the tracks are played in the selected order.
To cancel
Press [PROGRAM].
“CLEAR” is displayed and all the tracks are canceled. If a track was
playing, play continues to the end of the CD.
1
PROGRAM
Compact disc operations
PRGM
“FULL” is displayed
If 24 tracks have been programmed. No more tracks can be
programmed.
2
1
2
3
4
5
6
7
8
9
>10
Programmed
track number
Programmed
order
0
“- -:- -” is displayed
If total playing time for the tracks is over 199 minutes and 59
seconds or track numbered 25 or over was programmed. Tracks
can still be programmed and played.
PRGM
To check the contents of the program
Press [
/
] or [
/
] while stopped. The track numbers
and program position are displayed in order each time you press
the button.
PRGM
Total playing time
3
18
RQT5296
To add to the end of the program
Repeat step 2.
Canceling tracks (only while stopped)
From the last track
Press [CANCEL]. “CANCEL” is displayed.
A particular track
/
Select the track with [
] or
/
[
] then press [CANCEL].
All tracks
Press [■]. Program play is also cleared.
Before recording
Selection of tapes for recording
The unit automatically identifies the type of tape.
A
Normal position/TYPE 1
High position/ TYPE 2
Metal position/ TYPE 4
A
✔
✔
✔
To display the tape counter while recording
Press [COUNTER].
The counter is displayed for about five seconds.
B
COUNTER
B
Erasure prevention
The illustration shows how to remove the tabs to prevent recording.
To record on the tape again, cover as shown, being careful not to
cover the high position discrimination hole.
Side A
Volume and sound quality
Tab for side “B”
Recordings are unaffected by changes to volume and sound
quality.
Tab for side “A”
To re-record
Normal tape
C
Hi-position tape
Preparatory steps
1
Detection hole
C
2
3
1
Press [ OPEN/CLOSE], insert the
cassette with the tape facing in.
Make sure the cassette is fully inserted and press
[
OPEN/CLOSE] to close the deck.
2
Press [DOLBY NR] to select Dolby NR
on (“ NR” appears) or off.
(a “Dolby noise reduction” page 14).
3
1
Press [REV MODE] to select the
reverse mode.
Recording operations
Do these steps before each recording.
Wind up the leader tape so recording can begin immediately
(unnecessary if CD editing).
Each time you press the button:
: One side only records.
and
: Both sides record (forward → reverse).
“
” automatically changes to “
”
when [● REC PAUSE] is pressed.
OPEN/CLOSE
Erasing recordings
2
1.
2.
3.
4.
5.
DOLBY NR
Press [INPUT SELECTOR] to select “TAPE”.
Press [DOLBY NR] so that “
NR” goes off.
Select the reverse mode.
Press [● REC PAUSE].
Press [v] or [u].
NR
3
REV MODE
NR
19
RQT5296
A
Recording the radio
Preparation: Do the preparatory steps (a page 19).
2
■
3
1
Tune to the required station.
(a page 12 or 13)
2
Press [● REC PAUSE].
The deck goes into the recording standby mode, [● REC
PAUSE] indicator lights and a play indicator starts flashing.
3
v] or [u
u] to start recording.
Press [v
u: to record on the forward side
v: to record on the reverse side
To stop recording
Press [■].
To temporarily stop recording
Press [● REC PAUSE].
The deck goes into recording standby mode.
Press the [v] or [u] button with the flashing indicator to resume
recording.
■
A
2
Recording CDs
REC PAUSE
B
Normal recording
Preparation: Do the preparatory steps (a page 19).
1
Insert a CD.
Recording operations
(a page 16)
3
2
v] or [u
u] then [■] to set the
Press [v
tape direction.
u: to record on the forward side
v: to record on the reverse side
3
B
Press [● REC PAUSE].
The deck goes into the recording standby mode, [● REC
PAUSE] indicator lights and the play indicator starts flashing.
4
2
u] on the CD player.
Press [u
Recording starts automatically.
Four seconds after the CD finishes, the deck goes into the
recording standby mode.
3
4
REC PAUSE
To stop recording
EITHER
Press [■] on the CD player.
The deck goes into the recording standby mode four seconds later.
OR
Press [■] on the deck.
Recording stops immediately but the CD continues to play.
To record programmed tracks.
Program tracks after step 1 (a step 1 and 2, page 18).
20
RQT5296
Recording CDs
■
A
1 2
AI EDIT
One touch CD editing (AI EDIT)
The unit calculates the length of the tape and decides which tracks
go on which side of the cassette so tracks are not cut off midway.
Preparation: Do the preparatory steps (a page 19).
Insert a CD.
Press [AI EDIT].
The unit makes the calculations and “AI EDIT TAPE” scrolls across
the display. It takes a moment for recording to start.
■
A
After the deck completes recording the CD
It goes into recording standby mode. If there is space left on the
tape, “LINK” and the remaining time on the tape flash on the
display.
● If you have completed recording, press [■] on the deck or the CD
player.
● If you wish to continue recording with another CD, see “Linking”
below.
AI EDIT
To stop editing
Press [■] on the deck or the CD player.
“EDIT OUT” is displayed and both sections stop.
When tracks are allotted to both sides
When the tracks allotted to side A finish playing, the deck records to
the end of the side to complete calculation.
B
1
OPEN/CLOSE
Editing programmed tracks
Program the tracks (a step 1 and 2, page 18) and press [AI EDIT].
Note
2
B
Linking
If “LINK” is flashing and you wish to continue recording from another
CD, do the following.
1
Press [ OPEN/CLOSE] and insert
another CD.
Press [
2
OPEN/CLOSE] to close the tray.
Recording operations
Track numbered 25 or over cannot be recorded by one touch
editing. Use normal recording (a page 20).
u] on the CD player.
Press [u
Recording begins again.
You can continue linking tracks as long as there is space on the
tape. If you load a CD that has no tracks short enough to fit in the
remaining space, linking cannot be done.
To cancel
Press [■] on the deck or the CD player.
“EDIT OUT” scrolls across the display.
Linking programmed tracks
Program tracks after inserting the new CD (a step 1 and 2, page
18).
Your attention is drawn to the fact that recording pre-recorded
tapes or discs or other published or broadcast material may
infringe copyright laws.
21
RQT5296
Using the timers
3
PLAY/
The play timer
This timer starts play of the selected source at the selected time.
The example shows settings for preset radio channel 3 to play
between 6:30 and 7:40, Monday to Friday at –40 dB.
Preparation: Turn the unit on, set the time (a page 11), preset
radio stations if you want the timer to start playing the
radio (a page 13).
REC
1
q Press [CLOCK/TIMER, –DEMO] to
select “ PLAY.”
CLOCK
1
1
REC
Original display
w Press [SET] within 15 seconds.
2
2
1
PLAY
CLOCK/TIMER
q Press [TUNE/TIME ADJUST (∨ or ∧)]
to select the condition required and
w press [SET].
Repeat steps q and w to complete items q to t.
– DEMO
PLAY
2
q Select the day.
“SUN” ... “SAT” = One day of the week.
“SUN TO SAT” = Everyday of the week.
“MON TO SAT” = Everyday from Monday to
Saturday.
“MON TO FRI” = Everyday from Monday to
Friday.
“SAT, SUN” = Saturday and Sunday only.
SET
w Select the start time.
2
e Select the finish time.
q
1
r Select the source.
PLAY
TUNE/TIME ADJUST
w
TUNER
CD
TAPE
PLAY
If you select TUNER
e
2
Timer operations
Select a preset channel.
PLAY
t Select the volume.
r
SET
The timer is now on standby. The display shows each
condition again for 3 seconds each then restores the original
display.
Confirm the indicator next to [
PLAY/
REC] lights and
“
PLAY” on the display.
PLAY
PLAY
t
PLAY
3
/I
3
Press [
/I] to turn the unit off.
The timer starts at the set time with the volume increasing
gradually to the set level.
To cancel the timer
Turn the unit on.
On the remote control
Press [
PLAY] so “
PLAY” goes out.
On the main unit
Press [
PLAY/
REC] so “
PLAY” goes out.
Each time you press the button:
PLAY→
REC→
PLAY
REC→off (no display)
↑
The timer function will be canceled, but the settings stay in the
memory.
22
RQT5296
Using the timers
3
PLAY/
The record timer
This timer records the radio at the set time.
The example shows settings for recording preset channel 3 on
Saturday from 18:30 to 19:30.
Preparation: Turn the unit on, set the time (a page 11), preset
radio stations (a page 13).
REC
1
q Press [CLOCK/TIMER, –DEMO] to
select “ REC”.
CLOCK
PLAY
REC
Original display
w Press [SET] within 15 seconds.
1
1
1
2
2
CLOCK/TIMER
Repeat steps q and w to complete items q to r.
q Select the day.
– DEMO
REC
2
q Press [TUNE/TIME ADJUST (∨ or ∧)]
to select the condition required and
w press [SET].
“SUN” ... “SAT” = One day of the week.
“SUN TO SAT” = Everyday of the week.
w Select the start time.
SET
e Select the finish time.
r Select the preset channel.
The timer is now on standby. The display shows each
condition again for 3 seconds each then restores the original
display.
Confirm the indicator next to [
PLAY/
REC] lights and
“
REC” on the display.
2
q
1
TUNE/TIME ADJUST
REC
w
3
Press [
/I] to turn the unit off.
Recording starts 30 seconds before the set time with the
volume muted during the set time.
REC
e
To cancel the timer
REC
r
SET
REC
REC
3
/I
Turn the unit on.
On the remote control
Press [
REC] so “
REC” goes out.
On the main unit
Press [
PLAY/
REC] so “
REC” goes out.
Each time you press the button:
PLAY→
REC→
PLAY
REC→off (no display)
↑
Timer operations
2
The timer function will be canceled, but the settings stay in the
memory.
23
RQT5296
Using the timers
A
The play and record timers
Checking the timers
A
[
PLAY/
REC] indicator
Press [CLOCK/TIMER, –DEMO] to select “
PLAY” (or “
REC”)
The timer conditions are shown in the following order:
Day → start time → finish time → source → (“
PLAY” only) volume
The timers can be checked even if the unit is off.
Playing the unit after the timers are set
The unit can be used after the timers are set. Make sure the unit is
off before the set start time.
Note
If the unit is turned off while a timer is functioning, the finish time
setting will not be activated.
● The timers (either one or both) are set when the [
PLAY/
REC] indicator is on.
●
CLOCK/TIMER, –DEMO
CLOCK/TIMER
B
– DEMO
The sleep timer
Remote control only
This timer turns the unit off after a set time.
While playing a source
Press [SLEEP] to select the time (minutes).
Each time you press the button:
B
SLEEP 30
SLEEP
PLAY
SLEEP 60
SLEEP
SLEEP OFF
1
2
SLEEP 90
REC
SLEEP 120
3
> 10
4
5
6
7
8
9
To cancel the sleep timer
Press [SLEEP] to select “SLEEP OFF.”
“SLEEP” goes out.
0
PROGRAM
CANCEL
RANDOM
REPEAT
To confirm the remaining time
(While the timer is functioning)
Press [SLEEP].
The remaining time is shown for about five seconds.
AUTO/
MONO
MD
Timer operations
CD
TAPE
EXT/MD
TUNER
To change the setting
Press [SLEEP] to display the remaining time, then press again to
select the required time.
SLEEP
Note
SLEEP
The sleep timer is canceled if one touch editing is started.
Using the timers together
Any of the timers can be used together, but ensure the unit is off
before the start time for the record and play timers.
24
RQT5296
Using other equipment
●REC PAUSE
A
1
v, u
■
SC-HD310
DOLBY NR, REV MODE
Listening to an external source
Press [INPUT SELECTOR] to select
EXT/MD mode.
1
Each time you press [INPUT SELECTOR]:
TUNER
CD
TAPE
EXT/MD
On the remote control
Press [EXT/MD].
2
Operate the unit.
See the unit’s manual for details on operation and connection
(a page 8).
SC-HD510
1
A
1
INPUT SELECTOR,
–DVD DIRECT
B
Enjoying sound from a DVD player
SC-HD510 only
SC-HD510
SC-HD310
INPUT SELECTOR
INPUT
SELECTOR
Select the DVD mode to enjoy high quality from a DVD player
connected to the EXT/MD IN terminals.
Press and hold [INPUT SELECTOR ,
-DVD DIRECT] until “DVD” is displayed.
– DVD DIRECT
To cancel
Press [INPUT SELECTOR] to select another source.
Note
The DVD mode is designed specifically for use with DVD player.
The volume level will change if you select this mode while
equipment other than a DVD player is connected.
B
INPUT SELECTOR
– DVD DIRECT
Recording an external source
q Press [INPUT SELECTOR] to select EXT/MD
mode.
w Select Dolby NR and reverse mode.
e Press [● REC PAUSE].
r Press [v
v] or [u
u] to start recording.
t Start the source to be recorded.
See the unit’s manual for details on operation and connection.
To stop recording
Press [■] on the deck.
Recording onto an external unit
Reference
C
Start recording on the external unit and start playing the source to
be recorded.
C
Using headphones (not included)
Reduce the volume before connection.
Avoid listening for prolonged periods of time to prevent hearing
damage.
Plug type: 3.5 mm stereo.
25
RQT5296
Convenient functions
Adjusting the treble range
A
SC-HD510 only
BLFS
SC-HD510
FINE TWEETER
CONTROL
Fine adjustments to the treble range can be made due to separation
of the tweeter and woofer.
Turn [FINE TWEETER CONTROL].
Turn towards MAX to emphasize the treble or towards MIN to
lessen the effect.
Note
The effect is not noticeable through headphones.
Adjusting the bass-BLFS
B
SC-HD510 only
A
Use this feature to emphasize the bass (HIGH or LOW), or weaken
it (LIGHT).
FINE TWEETER CONTROL
Press [BLFS].
Each time you press the button:
BLFS HIGH
MIN
BLFS LOW
BLFS LIGHT
MAX
FLAT
B
BLFS
To cancel
Press [BLFS] to select “FLAT.”
BLFS
C
To adjust the tone quality
C
BASS
SC-HD310
TREBLE
SC-HD310 only
The level can be adjusted between -3 to +3.
Press [BASS] (low-frequency sound) or
[TREBLE] (high-frequency sound).
Each time you press the button;
+1
+2
+3
-3
-2
-1
0
To cancel
Press [BASS] or [TREBLE] to select “BASS 0” or “TREBLE 0”.
(“FLAT” will light.)
D
BASS
Muting the volume
Remote control only
Press [MUTING].
Volume is reduced to minimum.
TREBLE
Reference
To cancel
Press [MUTING] again. (“MUTING OFF” lights up.)
To cancel from the unit, turn [VOLUME] to minimum (- - dB), then
raise it to the required level.
Muting is also canceled when the unit is turned off.
D
MONO
MD
CD
TAPE
EXT/MD
TUNER
TUNE
MUTING
MUTING
Maintenance
TUNE
VOLUME
If the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
If the surfaces are extremely dirty, use a soft cloth dipped in a soapand-water solution or a weak detergent solution.
● Never use alcohol, paint thinner or benzine to clean this unit.
● Before using chemically impregnated cloth, read the instructions
that came with the cloth carefully.
MUTING
26
RQT5296
For a cleaner crisper sound
Clean the heads regularly to assure good quality playback and
recording. Use a cleaning tape (not included).
Troubleshooting guide
Before requesting service, make the below checks. If you can’t fix the system as described below, or if something not listed here occurs, refer to
the enclosed directory to locate an Authorized Service Center convenient to you or contact your dealer.
Reference pages are shown as black circled numbers y.
Common Problems
No sound.
Turn the volume up.
The speaker cords may be shorted. Turn the unit off, check and correct the connections and turn the
unit on. y
Sounds unfixed, reversed or
come from one speaker only
Check the speaker connections. y
Humming heard during play
An AC mains lead or fluorescent light is near the cables. Keep other appliances and leads away from
this unit’s cables.
If possible in your area, turn the AC mains lead’s plug or connector over to reverse the lead’s
polarity.
“ERROR” is displayed.
Incorrect operation performed. Read the instructions and try again.
“U70” is displayed
Connect the flat cables firmly. If “U70” remains on the display, contact the dealer.
“F61” is displayed.
There is a problem with the amplifier. Consult your dealer.
ECO mode on but display still
lights up in standby mode.
Turn DEMO off. !0
Listening to the radio
Noise is heard.
The stereo indicator flickers or
doesn’t light.
Sound is distorted.
Use an outdoor antenna. i
A beat sound is heard.
Turn the TV off or separate it from the unit.
A low hum is heard during AM
broadcasts.
Separate the antenna from other cables and leads.
The correct AM frequency can’t
be tuned in.
Change the frequency step. Hold [FM/AM] or [AM] down for 10 seconds to change the step to 9 kHz.
The cassette deck
Poor quality sound.
Clean the heads. @6
Check the Dolby NR setting. !4
Recording is not possible.
If the erasure prevention tabs have been removed, cover the holes with adhesive tape. !9
The CD player
The disc may be upside down. !6
Wipe the disc.
Replace the disc if it is scratched, warped, or nonstandard. !6
Condensation may have formed in the player due to a sudden change in temperature. Wait about an
hour for it to clear and try again.
During “One touch” editing (a Page 21)
“NO TAPE” is displayed.
Load a cassette. !4
“CHANGE TAPE” is displayed.
If the erasure prevention tabs have been removed, cover the holes with adhesive tape. !9
Reference
The display is wrong or play
won’t start.
The remote control
The remote control doesn’t work.
Check the batteries are inserted correctly. t
Replace the batteries if they are worn.
All components are required to service the system. If service is ever necessary, bring the entire system.
27
RQT5296
Technical specifications (DIN 45 500)
TUNER
■ Pre-amplifier section
Input sensitivity/impedance
EXT/MD IN
300 mV/15 kΩ
Output level/impedance
EXT/MD OUT
250 mV/1.5 kΩ
■ Tuner section
FM frequency range
87.50–108.00 MHz
(0.05 MHz step)
FM antenna terminal
75 Ω unbalance
AM frequency range
522–1629 kHz (9 kHz step)
520–1630 kHz (10 kHz step)
■ Timer section
Clock
Quartz lock type
Function
Play timer: 1 time or everyday
Rec timer: 1 time or everyday
Sleep timer: 120 min, 30 min intervals
■ GENERAL
Dimensions (W×H×D)
196×76.8×250 mm
Weight
1.0 kg
AMPLIFIER SC-HD510
■ Amplifier section
(Low frequency side)
Power output
DIN 1 kHz, THD 1%, 6 Ω both
channel driven
2×12 W
RMS 1 kHz, THD 10%, 6 Ω both
channel driven
2×15 W
Total harmonic distortion
Half power, 1 kHz, 6 Ω
0.09%
S/N
75 dB
Load impedance
6Ω
■ Amplifier section
(High frequency side)
Power output
DIN 10 kHz, THD 1%, 6 Ω both
channel driven
2×5 W
RMS 10 kHz, THD 10%, 6 Ω both
channel driven
2×8 W
S/N
75 dB
Load impedance
6Ω
■ Headphones
Jack type
3.5 mm STEREO
Load impedance
16–32 Ω
■ General
Power supply
For United Kingdom, Australia and N.Z.
AC 230–240 V, 50 Hz
For others
AC 230 V, 50 Hz
Power consumption
73 W
STANDBY condition
Normal
9W
Eco
0.8 W
Dimensions (W×H×D)
196×105.8×259.9 mm
Weight
3.3 kg
AMPLIFIER SC-HD310
SPEAKER SYSTEM SC-HD510
■ Amplifier section
Power output
DIN 1 kHz, THD 1%, 6 Ω both
channel driven
2×17 W
RMS 1 kHz, THD 10%, 6 Ω both
channel driven
2×20 W
Total harmonic distortion
Half power, 1 kHz, 6 Ω
0.09 %
Frequency response
50 Hz–20 kHz (+1 dB, –3 dB)
S/N
75 dB
Load impedance
6Ω
■ Headphones
Jack type
3.5 mm STEREO
Load impedance
16–32 Ω
■ General
Power supply
For United Kingdom
AC 230–240 V, 50 Hz
For others
AC 230 V, 50 Hz
Power consumption
67 W
STANDBY condition
Normal
9W
Eco
0.8 W
Dimensions (W×H×D)
196×105.8×259.9 mm
Weight
2.8 kg
Type 2 way, 2 speaker, bass-reflex system
Speaker(s)
Woofer:
12 cm cone type
Tweeter:
6 cm semi-dome type
Impedance
6Ω
Input power
High
30 W (Music), 15 W (DIN)
LOW
60 W (Music), 30 W (DIN)
Output sound pressure level
85 dB/W (1.0 m)
Cross over frequency
5 kHz
Frequency range
43 Hz–50 kHz (–16 dB)
50 Hz–45 kHz (–10 dB)
■ General
Dimensions (W×H×D)
For Australia and N.Z.
155×334×240 mm
For others
155×334×252 mm
Weight
For Australia and N.Z.
3.1 kg
For others
3.5 kg
CD PLAYER
Digital output terminal
Optical×1
■ Audio section
DA converter
1 bit 2 DAC MASH
■ Format
Sampling frequency
44.1 kHz
■ Pickup
Wavelength
780 nm
■ General
Dimensions (W×H×D)
196×76.8×243.1 mm
Weight
1.2 kg
CASSETTE DECK
■ Audio section
Track system
4 track 2 channel STEREO
Frequency response (Dolby NR off)
(Rec/Play)
TYPE 1 (NORMAL) 30 Hz–16 kHz (DIN)
TYPE 2 (HIGH)
30 Hz–16 kHz (DIN)
TYPE 4 (METAL)
30 Hz–16 kHz (DIN)
S/N (Signal level=max recording level,
TYPE 2)
NR off
56 dB (A weighted)
Dolby B NR
64 dB (A weighted)
■ Motor
Capstan drive
DC servo motor
Reel table drive
DC motor
Fast forward and rewind time (C-60)
Approx. 52 seconds
Wow and flutter
0.1% (WRMS)
■ General
Dimensions (W×H×D)
196×105.8×236.1 mm
Weight
1.5 kg
Matsushita Electric Industrial Co., Ltd.
Osaka 542-8588, Japan
SPEAKER SYSTEM SC-HD310
Type 2 way, 2 speaker, bass-reflex system
Speaker(s)
Woofer:
12 cm cone type
Tweeter:
6 cm cone type
Impedance
6Ω
Input power
60 W (Music), 30 W (DIN)
Output sound pressure level
85 dB/W (1.0 m)
Cross over frequency
6 kHz
Frequency range
45 Hz–25 kHz (–16 dB)
55 Hz–22 kHz (–10 dB)
■ General
Dimensions (W×H×D)
160×319×217 mm
Weight
3.0 kg
Notes:
1. Specifications are subject to change
without notice.
Weight and dimensions are approximate.
2. Total harmonic distortion is measured by
the digital spectrum analyzer.
En
RQT5296-B
H1299YY0(D)
Download PDF

advertising