Operator's Manual

Use and Care

IMPORTANT: READ THIS MANUAL BEFORE USING NEW COMMERCIAL SLICER

It is of extreme importance to take a few minutes and read this booklet thoroughly before using the new slicer. This will help you obtain the full benefits of the quality, convenience and safety built into this product. Used and maintained according to the following instructions, the slicer will give you years of trouble free service. Keep this booklet in a handy location for future reference.

IMPORTANT SAFEGUARDS

When using electric appliances, basic safety precautions should always be followed including the following:

1. READ ALL INSTRUCTIONS.

2. To protect against electrical hazards, DO NOT IMMERSE THE SLICER IN WATER OR ANY

OTHER LIQUID.

3. Unplug from outlet when not in use—also before putting on or taking off parts and before cleaning.

4. Do not operate this slicer with a damaged cord or plug or after the slicer has been dropped or damaged in any manner. Contact the nearest Service Agency for examination, repair or

6. Remove all attachments from slicer before washing.

7. NEVER LEAVE SLICER UNATTENDED while unit is operating.

8. The use of attachments not recommended by the manufacturer may cause hazards.

9. Follow manufacturer's instructions for use of attachments to be used with slicer.

10. KEEP OUT OF REACH OF CHILDREN.

11. SAVE THESE INSTRUCTIONS.

ASSEMBLY

The new slicer comes to you fully assembled and ready for use; however, the machine should be inspected for any signs of shipping damage. Even though it is anew machine, the slicer should be

thoroughly cleaned and sanitized before using to ensure sanitary conditions—follow the cleaning instructions found in this manual.

1

2

This safety information sheet is supplied with the slicer. Familiarize yourself with these guidelines and post the sheet near the slicer as a reminder.

2

INSTALLATION

The slicer is intended for placement on any rigid, level surface capable of supporting the weight of the machine. For normal counter top use it is not necessary to secure the slicer unless it is to be used on board ship or for similar applications.

NOTE: Before starting slicer the shipping gearbox oil plug should be replaced with the vented plug supplied with slicer. (Fig. 4) Save the shipping plug in the accessory box for possible future use

DISASSEMBLY FOR

CLEANING

CAUTION: Unplug slicer and set regulator knob to

"0" before cleaning or handling. (Fig. 5)

FOOD PUSHER REMOVAL

1. Slide platform to extreme forward position (toward you).

2. Unscrew and remove knob at end of food pusher shaft. (Fig. 6)

3. Slide food pusher up and off shaft. (Fig. 6)

3

FOOD FENCE REMOVAL

1. Loosen lock knob (counter-clockwise.) (Fig. 7)

2. Slide fence off of platform. (Fig. 7)

PLATFORM REMOVAL

1. Unscrew (counter-clockwise) and remove platform knob. (Fig 81)

2. Pull platform assembly straight out and off of slicer. (Fig. 9)

KNIFEWIPER REMOVAL

NOTE: The knifewiper is located at the lower back side of knife in the receiving area.

1. Unscrew and remove thumbscrew (counter-clockwise) (Fig. 10)

2. Remove knifewiper by pulling straight out.

4

KNIFE SHARPENER REMOVAL

CAUTION: EXTREME CARE SHOULD BE USED WHEN REMOVING THE KNIFE

SHARPENER AS THIS WILL LEAVE A PORTION OF THE KNIFE EX-

POSED.

1. Loosen the sharpener lock knob (on far side of sharpener, Fig. 11)

2. Pull sharpener straight up to its stop. (Fig. 12) DO NOT Unscrew knob.

3. Turn sharpener 1/2 turn clockwise. (Fig. 13)

4. Lift up to remove from slicer (Fig. 13)

KNIFE COVER REMOVAL

CAUTION: DO NOT TOUCH KNIFE. SHARP EDGES WILL CUT.

1. Platform should be removed as described earlier.

2. Unscrew (counter-clockwise) and remove knob and rod assembly. (Fig. 14)

3. Grasp knife cover by thumbscrews shown in figure 15.

4. Holding thumbscrews (Fig. 16) remove knife cover by pulling straight out and off of slicer.

5

CLEANING

The slicer should be thoroughly cleaned and sanitized before using the first time and after each day's operation or anytime the slicer is not to be used for an extended period of time.

Follow your companies sanitary standards as well as state and local health codes.

IMPORTANT: For your safety always wear protective cut-resistant gloves when cleaning

the knife or in the area of the knife.

UNPLUG slicer before cleaning.

NEVER use steel pads or abrasive cleaners.

1. Using a mild soap, hot water and a clean cloth carefully wash both sides of knife by wiping outward from the center. Rinse knife in the same manner using another clean cloth and fresh water.

2. Wash and rinse both sides of the knife cover. Re-install the knife cover.

3. Clean the knife sharpener. Be sure that the stones are free of grease and food particles. Use the wire brush supplied in the accessory box if necessary.

(Fig. 17)

4. Re-install the knife sharpener and tighten lock knob.

DO NOT immerse the slicer base in water.

DO NOT direct spray cleaners at switch area or into

the openings of the machine.

5. Wipe all surfaces of the slicer with the mild soap solution and rinse.

6. Clean a!l remaining parts in the same manner.

DO NOT wash any slicer parts in a dishwasher.

To clean under the ASM-HD raise the lift lever and move it past the center position until it locks. (Fig. 18) After cleaning pull the lift lever release knob and hold out (Fig. 19) then slowly move the lift lever back toward the front of the slicer lowering it back down

.

6

Reassemble the remaining parts to the slicer.

When installing the platform always be sure to tighten the lock knob. The label at right appears on the machine as a reminder. (Fig. 20)

ELECTRICAL POWER SUPPLY

The slicer should be placed close enough to the electrical power supply so that an extension cord will not be needed. The slicer is designed to be used on 115 Volt,

A.C., 60 Hz power source, as indicated on the Data Plate which is affixed to the rear of the unit. (Fig. 21) BE SURE

THAT THE VOLTAGE IS THE SAME BEFORE

PLUGGING SLICER INTO OUTLET. To operate the unit on other voltages, the unit must be returned to the factory

ALWAYS USE A PROPERLY GROUNDED THREE-

PRONG OUTLET TO REDUCE THE HAZARD OF

ELECTRICAL SHOCK.

NOTE: It is important that all electrical connections be made in compliance with all applicable local electrical codes as well as the latest edition of the National

Electrical Code.

OPERATION

SLICING—MODEL SM-HD OR MANUAL OPERATION OF MODEL

ASM-HD

1. Place platform drive engagement lever in the down (disengaged) position, (Fig. 22)

2. Set platform speed control knob to zero slices per minute. (Fig. 23)

7

3. Pull platform all the way toward you until it reaches its stop.

4. With food pusher out of the way (stored in holder) place product to be cut on platform.

5. Adjust the food fence by loosening the knob and sliding the fence so that it is close to the product but not pushing against it. Tighten the knob. (Fig. 24)

6. Place food pusher behind product to be cut. (Fig. 25)

7. Set regulator knob for desired slice thickness and start slicer. (If the slicer is equipped with the regulator knob "shut-off" option, the motor can be turned ON and OFF with the use of the regulator knob while power switch is in ON position ) ALWAYS TURN

POWER SWITCH TO "OFF" POSITION WHEN SLICER IS NOT IN USE.

8. Using platform reciprocating handle, move platform back and forth for each slice. (Fig.

26) Be sure to push platform far enough forward to complete the slice, then pull back until the food being cut clears the cutting edge of the knife.

The slicer is gravity fed; however, use of the food pusher is important to prevent personal injury, particularly when slicing small pieces of food. NEVER FEED FOOD BY HAND;

ALWAYS USE FOOD PUSHER.

8

SLICING—MODEL ASM-HD AUTOMATIC OPERATION

1. With power switch in OFF position, set platform speed control to zero slices per minute. (Fig. 23).

2. Pull platform all the way toward you until it reaches its stop.

3. Place food on platform, adjust fence and set food pusher in place. (Fig. 24 & 25)

4. Place platform drive engagement lever in up

(engaged) position. (Fig. 27)

5. Set regulator knob for desired slice thickness and

start slicer. (If the slicer is equipped with the

regulator knob "shut-off" option, the motor can

be turned ON and OFF with the use of the regulator

knob while power switch is in ON position.)

ALWAYS TURN POWER SWITCH TO "OFF"

POSITION WHEN SLICER IS NOT IN USE.

6. Turn platform speed control knob to ten (10) slices per minute. After platform drive engages platform, set speed control to desired slices per minute.

NOTE: Slower speeds should be used for thick cuts or hard foods.

MAINTENANCE

SHARPENING THE KNIFE

1. SHUT OFF AND UNPLUG SLICER.

2. Turn regulator knob to zero.

3. Set platform speed control knob to zero. (ASM-HD only)

4. Place platform drive engagement lever

in the down (disengaged position.) (ASM-HD

only)

5. CAREFULLY clean knife removing all

grease and food particles to prevent clogg-

ing of sharpener stones.

6. While slicer is OFF loosen the sharpener

lock knob. (Fig. 28)

9

7. Pull up (Do not unscrew) Sharpener using knob on top. Fig. 29)

8. Rotate sharpener clockwise one-half turn (180). (Fig. 30).

9. Push down (Fig. 30). Lock into position using lock knob. (Fig. 28)

10.

Plug in and turn slicer ON. DO NOT TOUCH KNIFE. Let stone grind knife for five (5) seconds or until desired edge is obtained.

11.

Push in button for deburring stone (Fig. 31) and hold in for 2-3 seconds until edge is smooth and free of burrs.

12.

When the proper edge has been obtained through sharpening and deburring shut OFF and unplug slicer.

13. Return sharpener to its original stored position and tighten lock knob. (Fig. 28)

IMPORTANT: After sharpening, clean both sharpener and knife. Before slicing again be sure

that all steel particles from grinding have been removed to prevent contamination of food.

NOTE: A knife sharpening guide sheet is supplied with the slicer. Keep it in a handy location for future reference.

TRANSMISSION AND GEAR MAINTENANCE

The slicer is equipped with a gear driven transmission and contains special gear oil. The gear oil should not need changing, unless the transmission or motor has been removed. Consult a factory authorized service agency or the factory for gearbox maintenance information.

10

LUBRICATION

To insure continued smooth operation of sliding parts use the oil supplied in the accessory box or a light mineral oil as follows:

1) Apply about ten drops of oil to the platform shaft about once per month. (Fig. 32)

2)

Apply 2-3 drops of oil to the food pusher shaft and the knife cover rod after each washing.

(Fig. 33)

WEAR ADJUSTMENT

After several years of operation and many sharpenings of the knife, it may be necessary to have the regulator plate adjusted closer to the knife. Contact the factory authorized service agency or the factory if this service becomes necessary as this service must be performed by an authorized technician.

11

REPLACEMENT PARTS

MODELS: SM—HD & ASM—HD

KEY

NO.

PART NO. NAME/DESCRIPTION

401 23-SM-1401 Base

402 23-SM-1402 Regulator Plate

403 23-SM-1403 Bracket: Regulator Plate

404 8-SM-1404 Screw: Reg. Plate Brkt.

405 8-SM-1405 Washer: Reg. Plate Brkt.

407 9-SM-1407 Support Post: Reg. Plt.

408 9-SM-1408 Knob: Knife Cover

409 9-SM-1409 Rod: Knife Cover

410 9-SM-1410 Extension: Knife Shaft

411 9-SM-1411 Shaft: Knife

412 8-SM-1412 Retaining Ring: Worm Gear

413 8-SM-1413 Spacer: Worm Gear

414 9-SM-1414 Worm Gear: Knife Drive

415 7-SM-1415 Seal: Knife Hub

416 6-SM-1713 Pad: Knife Drive Gear

417 4-SM-1696 Knife Hub (Std Knife)

* 4-SM-1698 Knife Hub (Long Taper)

** 30-SM-1696 Knife Hub Assembly: (Std Knife)

** 30-SM-1698 Knife Hub Assembly: (Lg Taper)

(Inc: 411-422, 606,607)

418 8-SM-1418 Bearing: Knife

419 8-SM-1419 Spacer: Knife Bearing

420 7-SM-1420 Bearing Retainer

421 8-SM-1421 Nut: Knife Shaft

422 8-SM-1422 Set Screw: Knife Shaft

423 9-SM-1423 Knife: Stainless Steel (Std)

* 9-SM-1712 Knife: S/S (Long Taper)

424 8-SM-1424 Screw: Standard Knife

* 8-SM-1032 Screw: Long Taper Knife

425 8-SM-1425 Spacer: Knife Cover

426 23-SM-1426 Knife Cover

427 8-SM-1427 Thumbscrew: Knife Cover

428 8-SM-1568 Screw: Motor Cover

429 23-SM-1429 Motor Cover

430 8-SM-1430 crew: Motor Mounting

431 8-SM-1431 Washer: Mtr. Mtg. Screw

432 30-SM-1697 Motor Assy: 115V, 50/60 HZ

* 30-SM-1430 Motor Assy: 220V, 50/60 HZ

433 7-SM-1433 Seal: Motor Shaft

434 7-SM-1434 Gasket: Motor

435 9-SM-1717 Drive Gear

436 8-SM-1436 Key: Drive Gear

437 8-SM-1437 Spacer: Spring

438 8-SM-1438 Spring: Drive Gear

439 8-SM-1439 Retaining Nut: Mtr. Shaft

440 9-SM-1440 Knife Wiper

441 8-SM-1441 Thumb Screw: Knife Wiper

442 9-MM-2099 Strain Relief Bushing

443 9-SM-1443 Bushing: Regulator Knob

445 9-SM-1445 Ratchet Pin Assy. W/ Jam Nut

QTY

PER

MACH.

KEY

NO.

PART NO. NAME/DESCRIPTION

1 447 9-SM-1447 Regulator Knob

1 454 8-SM-1561 Nut

1 461 6-6-2192 Rubber Boot: Switch

2 462 5-6-4581 Switch Guard

2 463 6-SM-1463 Foot (SM-HD)

464 9-SM-1559 Oil Plug: Drain

1 465 8-SM-1465 Platform Rail

1 466 8-SM-1466 Screw: Platform Shaft

1 467 8-SM-1467 Washer: Platform Shaft

1 468 7-SM-1468 Rubber Bumper

1 469 9-SM-1469 Extension: Platform Shaft

1 470 8-SM-1470 Bumper Spring: Platform Shaft

1 471 9-SM-1471 Platform Shaft

1 472 1-SM-1472 Platform Carriage

1 473 5-6-1501 Switch: 115 Volt

3 * 5-6-1507 Switch: 220 Volt

1 474 5-SM-1503 Running Light: 115 Volt

1 * 5-SM-1300 Running Light: 220 Volt

QTY

* 8-SM-1504 Push-On Fastener: Light

476 5-SM-1476 Capacitor: 115 Volt

1 * 5-SM- 860 Capacitor: 220 Volt

2 477 8-SM-1477 Bracket: Capacitor

1 478 5-SM-1239 Cordset: 115 Volt

1 479 8-SM-1240 Wire Clamp: Cordset

1 483 9-SM-1483 Handle: Food Pusher

1 493 23-SM-1493 Bracket: Platform

1 494 9-SM-1494 Handle: Platform

1 * 8-SM-1495 Screw: Handle

1 4979-SM-1497 Roller Bracket: Platform

1 ** 30-SM-1497 Roller Brkt. Assy.: Inc. Roller

1 504 23-SM-1504 Sharpener Bracket

1 505 8-SM-1505 Washer: Sharpener Brkt

2 506 8-SM-1506 Screw: Sharpener Brkt

2 507 8-SM-1542 Lug: Sharpener Brkt

1 508 8-SM-1508 Stop Nut: Sharpener Brkt.

4 509 9-SM-1509 Rod: Lock Knob

4 510 9-SM-1510 Shaft: Sharpener Frame

1 511 8-SM-1557 Stop Screw: Shrpnr Frm

1 512 8-SM-1512 Jam Nut: Stop Screw:

1 513 23-SM-1513 Sharpener Housing

1 ** 30-SM-1513 Sharpener Assy, Complete

1 514 8-SM-1514 Washer: Sharpener Hsg.

1 515 8-SM-1515 Nut: Sharpener Hsg.

1 516 9-SM-1516 Knob: Sharpener Hsg.

1 580 8-SM-1525 Nut: Sharpener Frame

1 581 8-SM-1021 Retaining Ring: Stone Shaft

1 582 9-SM-1705 Sharpener Frame

1 583 8-SM-1523 Spring: Stone Shaft

1 584 9-SM-1721 Shaft: Sharpening Stone

1 585 9-SM-1722 Button: Deburring Stone

1 586 8-SM-1723 Set Screw: Dbrg Stone Button 1

1

1

1

2

1

1

1

1

1

2

1

1

1

1

1

1

1

1

1

1

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

2

2

2

PER

MACH.

1

3

1

1

4

1

GENERAL SLICING/RED GOAT DISPOSERS

REPLACEMENT PARTS

MODELS: SM—HD & ASM—HD

KEY

NO.

PART NO.

NAME/DESCRIPTION

587 9-SM-1724 Shaft: Deburring Stone

588 9-SM-1531 Deburring Stone

589 9-SM-1535 Sharpening Stone

598 30-SM-1623 Bottom Cover Assy

599 4-SM-1725 Cover Plate: Reg. Mech.

600 8-SM-1726 Rivet: Knife Wiper

601 8-SM-1727 Set Screw: Reg. Worm

602 30-SM-1443 Regulator Worm Assy

QTY

PER

1

1

1

3

KEY

NO.

PART NO.

NAME/DESCRIPTION

MAC

1 655 8-SM-1733 Bumper Spring: Platform

1

QTY

PER

MACH.

1

Carriage

1 656 8-SM-1117 Screw: Capacitor Clamp

2

1

1 658 6-SM-1540 Roller Assy: Platform

1 659 8-SM-1735 Washer: Platform Shaft Ext.

1

1

1 *not illustrated

604 8-SM-1451 Washer: Reg. Worm

605 8-SM-1456 Screw: Reg. Worm

606 8-SM-1728 Screw: Mtg. Ring

607 4-SM-1729 Mounting Ring: Knife Gr.

608 9-SM-1559 Oil Plug: Shipping

* 9-SM-1560 Oil Plug: Vented

1

1

1

616 8-SM-1450 Pivot Pin Assy: Reg. Plt. Brkt.

1

*

* not illustrated as assembly

617 1-SM-1567 Bracket: Regulator Slide

618 1-SM-1448 Regulator Slide

1

1

619 9-SM-1473 Stop Plate: Reg. Slide 1

620 9-SM-1462 Brass Bushing: Reg. Slide 2

621 8-SM-1551 Screw: Reg. Slide

622 8-SM-1446 Limit Screw: Reg. Slide

623 8-SM-1455 Set Screw: Reg. Slide

624 8-SM-1730 Set Screw: Reg. Slide

1

1

2

2

2

1

1

1

625 8-SM-1731 Jam Nut: Set Screw

626 9-SM-1452 Regulator Plate Bracket

627 8-SM-1459 Screw: Spring

628 8-SM-1460 Nut: Pivot Pin

629 8-SM-1458 Washer: Pivot Pin

630 9-SM-1461 Spring: Worm Follower

1

1

631 9-SM-1453 Worm Follower 1

632 8-SM-1454 Retaining Ring: Worm Follower 1

633 8-SM-1732 Mtg Screw: Reg. Slide Brkt

634 8-SM-1541 Screw: Roller Bracket

636 9-SM-1274 Knob: Platform

637 8-SM-1539 Stud: Platform Knob

638 8-SM-1488 Screw: Food Pusher Brkt

639 9-SM-1489 Bracket: Food Pusher

640 9-SM-1484 Shaft: Food Pusher

641 9-SM-1490 Knob: Food Pusher Shaft

3

1

1

1

2

1

1

1

642 23-SM-1480 Food Pusher Arm

644 8-SM-1482 Stud: Food Pusher Handle

1

1

645 23-SM-1481 Food Pusher w/ Spikes (SM-HD)

* 9-SM-1125 Spike: Food Pusher

1

*

* 6-SM-1486 Nylon Rider: Food Pusher

6-SM-1487 Rubber Spacer: Food Pusher

17

5

1

646

647

648

23-SM-1554

23-SM-1491

9-SM-1564

Adjustment Fence

Platform

Knob: Adjustment Fence

653 8-SM-1016 Jam Nut: Stone Shaft

654 4-SM-1734 Bottom Cap: Reg. Plate 1

1

1

1

2

GENERAL SLICING/RED GOAT DISPOSERS

GENERAL SLICING/RED GOAT DISPOSERS

REPLACEMENT PARTS

MODEL: ASM—HD

KEY

NO.

PART NO.

QTY

PER

KEY

NO.

PART NO.

300 1-SM-1593

NAME/DESCRIPTION MACH.

Base (ASM-HD)

NAME/DESCRIPTION

1 340 8-SM-1742 Lockwasher: Gearbox

301

302

303

304

305

306

307

308

315

324

325

326

327

328

332

333-

334

335

336

337

338

1-SM-1569

1-SM-1603

8-SM-1594

4-SM-1600

9-SM-1709

9-SM-1638

6-SM-1695

8-SM-1582

8-SM-1584

8-SM-1586

4-SM-1623

2-SM-1606

9-SM-1574

9-SM-1575

9-SM-1576

4-SM-1587

4-SM-1580

8-SM-1737

8-SM-1634

8-SM-1648

8-SM-1605

8-SM-1739

9-SM-1740

8-SM-1578

8-SM-1738

Carriage: Platform

Support: Oscillation Arm

Lever, Engagement

Oscillation Arm

Food Pusher W/spikes

(ASM-HD)

Knob: Lift Lever

Foot (ASM-HD)

Retaining Ring:

Connecting Arm

Bearing: Oscillation Arm

Bushing: Pivot Arm

Bottom Cover

Motor (D.C.)

Spring: Oscillation Arm

Spindle: Roller Bushing

Roller Bushing:

Oscillation Arm

Pivot Arm Assy.

Connecting Arm

Key: D.C. Motor

Support

Clamp Block: Lift Lever

Bearing Retainer

Screw: DC Motor

Mounting

Mounting

339 8-SM-1741 Washer: Gearbox

309 8-SM-1609 Key: Pivot Arm Assy.

310

311

312

313

314 9-SM-1589 Gear Box Assembly

329

30-SM-1606

4-SM-1658

Gear Motor Assy.

(Inc. 314)

Cover Plate: Oscillation

Arm Sup.

330 9-SM-1707 Lift Lever

331 8-SM-1651 Spacer: Osc. Arm

Stud: Housing Assembly

Release Pin: Lift Lever

Knob: Lift Lev. Rel. Pin

Spacer: Connecting Arm

1

1

Mounting

1 341 8-SM-1743 Nut: Gearbox Mounting

1 342 8-SM-1592 Screw: Gearbox Mounting

1 343 5-SM-1708 Brush Assy.: DC Motor

344 9-SM-1744 Cap: DC Motor Brush

1 345 8-SM-1604 Set Screw: Oscillation

4 Arm Support

2 346 8-SM-1647 Screw: Bearing Retainer

1

347 8-SM-1598 Screw: Roller Bushing

Spindle

1 348 8-SM-1597 Washer: Rlr Bush.

SpdI/Btm Cvr.

2

1 349 8-SM-1595 Set Screw: Engage.Lever

1 350 8-SM-1571 Screw: Carriage

1 351 8-SM-1577 Screw: Oscillation Arm

Roller Bush.

1 352 8-SM-1599 Set Screw: Oscillation Arm

1 353 8-SM-1745 Jam Nut: Oscillation Arm

1 Set Screw 316

317

318

319

9-SM-1736

9-SM-1570

8-SM-1657

9-SM-1632

Spring: Lift Lev. Rel. Pin

Spring: Carriage

Support

Roller: Lift Lever

Stud: Oscillation Arm

2 357 30-MM-2085 Speed Control: D.C. Motor

2 358 8-SM-1655 Nut: Osc. Arm Sup/

Clamp BIk

1 359 8-SM-1431 Washer: Clamp Block

320 8-SM-1585 Screw: Oscillation Arm 1 360 8-SM-1583 Washer: Connecting Arm

321 8-SM-1607 Pivot Pin: Connecting Arm 1 362 8-SM-1596 Engagement Bracket

322 8-SM-1573 Bushing: Oscillation Arm

323 8-SM-1572 Engagement Cam Pin *

1 363 30-MM-2086 Potentiometer W/Wires

1 364 9-SM-1616 Label: Control

1 365 5-6-1626 Circuit Breaker

1 366 5-MM-2060 Knob: Speed Control

368 8-SM-1276 Nut: Housing Assy. Stud

1 369 8-SM-1640 Screw: Bottom Cover

1 370 8-SM-1635 Stop Pin: Lift Lever

1 371 8-SM-1637 Screw: Lift Lev. Clamp BIk

1 372 8-SM-1633 Pin: Lift Lvr Rlr/

Engage.Lvr

1 377 8-SM-1659 Screw: Oscillation Arm

2 Support

378 8-SM-1652 Washer: Oscillation

1 Arm Sup Screw

1 379 8-SM-1591 Screw: Pivot Arm Assy.

4 380 8-SM-1590 Washer: Pivot Arm Assy.

1 381 8-SM-1076 Slide Screw: Carriage

1

2

4

4

QTY

PER

MACH.

4

1/4

1

2

1

4

2

2

1

4

2

1

2

2

1

2/2

2

2

1

1

1

1

1

4

4

2

2

1

1

1

1

2

2/1

GENERAL SLICING/RED GOAT DISPOSERS

GENERAL SLICING/RED GOAT DISPOSERS