Cadillac 2007 CTS Automobile User Manual

FS-Y1[B]_f.book Page 1 Friday, April 15, 2005 7:46 PM
COMPACT COMPONENT SYSTEM
FS-Y1
Consists of CA-FSY1 and SP-FSY1
INSTRUCTIONS
GVT0142-008A
[B]
FS-Y1[B]_f.book Page 1 Friday, April 22, 2005 1:43 PM
Warnings, cautions and others
IMPORTANT for the U.K.
DO NOT cut off the mains plug from this equipment. If the plug
fitted is not suitable for the power points in your home or the
cable is too short to reach a power point, then obtain an
appropriate safety approved extension lead or consult your
dealer.
BE SURE to replace the fuse only with an identical approved
type, as originally fitted.
If nonetheless the mains plug is cut off ensure to remove the
fuse and dispose of the plug immediately, to avoid a possible
shock hazard by inadvertent connection to the mains supply.
If this product is not supplied fitted with a mains plug then
follow the instructions given below:
IMPORTANT:
DO NOT make any connection to the terminal which is marked
with the letter E or by the safety earth symbol or coloured
green or green-and-yellow.
The wires in the mains lead on this product are coloured in
accordance with the following code:
Blue:
Neutral
Brown: Live
As these colours may not correspond with the coloured
markings identifying the terminals in your plug proceed as
follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
CAUTION — STANDBY/ON
button!
Disconnect the mains plug to shut the power off
completely (the STANDBY lamp goes off).
The STANDBY/ON
button in any position does
not disconnect the mains line.
• When the system is on standby, the STANDBY
lamp lights red.
• When the system is turned on, the STANDBY
lamp lights green.
The power can be remote controlled.
CAUTION
• Do not block the ventilation openings or holes. (If
the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able
to get out.)
• Do not place any naked flame sources, such as
lighted candles, on the apparatus.
• When discarding batteries, environmental
problems must be considered and local rules or
laws governing the disposal of these batteries
must be followed strictly.
• Do not expose this apparatus to rain, moisture,
dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
G-1
FS-Y1[B]_f.book Page 2 Friday, April 22, 2005 1:43 PM
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are
no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation
when open and interlock failed or defeated. Avoid
direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL,
PLACED INSIDE THE UNIT.
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the
apparatus as follows:
1. Front:No obstructions and open spacing.
2. Sides/Top/Back:No obstructions should be placed in the areas shown by the
dimensions below.
3. Bottom:Place on the level surface. Maintain an adequate air path for
ventilation by placing on a stand with a height of 10 cm or more.
Front view
Wall or obstructions
Side view
Wall or obstructions
15 cm
15 cm
15 cm
1 cm
CA-FSY1
1 cm
CA-FSY1
10 cm
G-2
FS-Y1[B]_f.book Page 3 Friday, April 22, 2005 1:43 PM
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been designed and manufactured to meet international safety standards but, like any electrical
equipment, care must be taken if you are to obtain the best results and safety is to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between
pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and
withdraw the mains plug when making or changing connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in
any way — switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for
unattended operation or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic
safety. It is illegal to watch television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the
manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
—NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case — this
could result in a fatal electrical shock.;
—NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than sorry!
E43486-340B
G-3
FS-Y1[B]_f.book Page 2 Friday, April 15, 2005 7:46 PM
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are
no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation
when open and interlock failed or defeated. Avoid
direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL,
PLACED INSIDE THE UNIT.
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the
apparatus as follows:
1. Front:No obstructions and open spacing.
2. Sides/Top/Back:No obstructions should be placed in the areas shown by the
dimensions below.
3. Bottom:Place on the level surface. Maintain an adequate air path for
ventilation by placing on a stand with a height of 10 cm or more.
Front view
Wall or obstructions
Side view
Wall or obstructions
15 cm
15 cm
15 cm
1 cm
CA-FSY1
1 cm
CA-FSY1
10 cm
G-2
FS-Y1[B]_f.book Page 3 Friday, April 15, 2005 7:46 PM
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been designed and manufactured to meet international safety standards but, like any electrical
equipment, care must be taken if you are to obtain the best results and safety is to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between
pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and
withdraw the mains plug when making or changing connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in
any way — switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for
unattended operation or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic
safety. It is illegal to watch television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the
manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
—NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case — this
could result in a fatal electrical shock.;
—NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than sorry!
E43486-340B
G-3
FS-Y1[B]_f.book Page 1 Friday, April 15, 2005 7:46 PM
Table of contents
Introduction
About discs......................................................3
Description of parts .........................................5
Getting started
Using the remote control .................................6
Putting the batteries in the remote control .......... 6
Operating the TV using the remote control......... 7
Connecting up .................................................8
Basic operations
Playing discs .................................................12
Playback ........................................................... 12
To switch the display ........................................ 13
Select what you want to play by using
the number buttons.................................... 14
To stop playback............................................... 14
To pause playback............................................ 14
To advance picture frame-by-frame.................. 14
Fast reverse/Fast forward search ..................... 14
Playing back from a position 10 seconds
before (One Touch Replay) ....................... 15
Slow Motion Playback....................................... 15
Skip to the beginning of the selection ............... 15
To change the brightness of
the display window (DIMMER) .................. 16
Adjusting the volume ........................................ 16
Adjusting sound quality..................................... 16
Turning off the sound temporarily (MUTING) ... 16
Introduction
Functions specific to DVD AUDIO.................27
Playing the Bonus Group...................................27
Browsable Still Pictures (B.S.P.) .......................27
Using the menu bar .......................................28
Preferences ...................................................29
Country/Area codes.......................................31
Listening to radio
Listening to a radio broadcast .......................32
Tuning in to a preset station ..........................33
Using the RDS...............................................34
Using the RDS (Radio Data System) when
receiving FM stations...................................34
Convenient functions
Listening to the sound of other audio device ....38
Setting the various timer................................38
Setting the built-in clock.....................................38
Setting the daily timer ........................................38
Auto Standby .....................................................39
Sleep Timer .......................................................40
Tray Lock.......................................................40
Reference
Troubleshooting.............................................41
Language codes............................................42
Specifications ................................................43
Advanced operations
Playing audio/video files................................16
Resume Playback .........................................18
Select the scene to be played .......................19
Program Playback/Random Playback...........20
Repeat Playback ...........................................22
Other convenient functions............................24
Selecting the subtitles....................................... 24
Selecting the audio language ........................... 24
Selecting a view angle ...................................... 24
Enlarging the picture (ZOOM)........................... 25
Adjusting the picture quality (VFP) ................... 25
Creating realistic sound (3D PHONIC) ............. 26
Adjusting playback level (DVD LEVEL) ............ 26
Enjoying better pictures (SCAN MODE) ........... 26
How to read this manual
• Operations are described by mainly using the
remote control buttons. If there are the same
marks on the main unit, the buttons on the main
unit can also be used.
• The following marks tell you for which type of the
discs the operation can be made.
• The illustrations and TV screens may be different
between the actual case and the description.
• “VCD” is an abbreviation of “Video CD”.
• “SVCD” is an abbreviation of “Super Video CD”.
1
FS-Y1[B]_f.book Page 2 Friday, April 15, 2005 7:46 PM
Special cautions
Care of the cabinet
When cleaning the system, use a soft cloth and follow the
relevant instructions on the use of chemically-coated
cloths. Do not use benzene, thinner or other organic
solvents including disinfectants. These may cause
deformation or discoloring.
Notes on handling
7 Important cautions
Installation of the system
• Select a place which is level, dry and neither too hot
nor too cold; between 5°C and 35°C.
• Leave sufficient distance between the system and the
TV.
• Do not use the system in a place subject to vibration.
Power cord
• Do not handle the power cord with wet hands.
• A small amount of power is always consumed while
the power cord is connected to the wall outlet.
• When unplugging the power cord from the wall outlet,
always pull on the plug, not the power cord.
To prevent malfunctions of the system
• There are no user-serviceable parts inside. If anything
goes wrong, unplug the power cord and consult your
dealer.
• Do not insert any metallic object into the system.
• Do not use any non-standard shape disc (like a heart,
flower or credit card, etc.) available on the market,
because it may damage the system.
• Do not use a disc with tape, stickers, or paste on it,
because it may damage the system.
Label sticker
Sticker
Paste
Note about copyright laws
Check the copyright laws in your country before
recording from DVDs, VCDs, SVCDs, and CDs.
Recording of copyrighted material may infringe copyright
laws.
If water gets inside the system
Turn the system off and disconnect the power cord plug
from the wall outlet, then call the store where you made
your purchase. Using the system in this condition may
cause fire or electrical shock.
7 When condensation or water drops adhere to the
lens
In any of the following cases, condensation or water
drops may adhere to the lens to prevent the system from
working properly:
• Immediately after starting to heat the room
• When the system is installed in a steamy or damp
space
• When the system is suddenly moved from a cold place
to a warm space
In any of these cases, leave the system turned on for 1 or
2 hours before use.
Supplied accessories
Check to be sure you have all of the supplied
accessories.
The number in parentheses is the quantity of the pieces
supplied. If anything is missing, contact your dealer
immediately.
•
•
•
•
•
•
•
Remote control (1)
Batteries (2)
FM antenna (1)
AM loop antenna (1)
Power cord (1)
Composite video cord (1)
Speaker cords (2)
Note about copy guard system
DVDs are protected by copy guard system. When you
connect the system to your VCR directly, the copy guard
system activates and the picture may not be played back
correctly.
7 Safety precautions
Avoid moisture, water and dust
Do not place the system in moist or dusty places.
Avoid high temperatures
Do not expose the system to direct sunlight and do not
place it near a heating device.
When you are away
When away on travel or for other reasons for an extended
period of time, disconnect the power cord plug from the
wall outlet.
Do not block the vents
Blocking the vents may damage the system.
• Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, “MLP Lossless”, and the double-D
symbol are trademarks of Dolby Laboratories.
• “DTS” and “DTS 2.0+DIGITAL OUT” are registered trademarks of Digital Theater Systems, Inc.
• This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents
and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
2
FS-Y1[B]_f.book Page 3 Friday, April 15, 2005 7:46 PM
About discs
Introduction
* Note on Region Code
Playable disc types
This system has been designed to play back the following
discs:
DVD VIDEO, DVD AUDIO, VCD, SVCD, CD
This system can also play back the following discs:
• Finalized DVD-R/-RW discs recorded in the DVD
VIDEO format.
• CD-R/RW discs recorded in the following formats
• Music CDs (finalized discs)
• VCDs
• SVCDs
• MP3/WMA/JPEG discs recorded in ISO 9660 (for
details, refer to “Notes on CD-R and CD-RW ”)
DVD players and DVD VIDEOs have their own Region
Code numbers. This system can only play back a DVD
VIDEO recorded with the Region Code number and
video format mentioned below.
For your available Region Code, check the rear panel
of your main unit.
This system can play back only DVD VIDEOs whose
Region Code numbers include “2”.
Examples:
However, some discs may not be played back because of
their disc characteristics, recording conditions, or
damage or stain on them.
Only sounds can be played back from the following discs:
MIX-MODE CD
CD-G
CD-EXTRA
CD TEXT
If a DVD VIDEO with an improper Region Code
number is loaded, “REGION CODE ERROR!” appears
on the TV screen and playback cannot start.
• On some DVD VIDEOs, DVD AUDIOs, VCDs or SVCDs,
their actual operation may be different from what is
explained in this manual. This is due to the disc
programming and disc structure, not a malfunction of
this system.
Discs you can play:
Notes on DVD-R and DVD-RW
Disc
Type
Mark (Logo)
DVD
VIDEO
DVD
AUDIO
VCD
Video
Format
PAL
AU D I O
—
PAL
• This system can also play finalized DVD-Rs or DVDRWs recorded in DVD-Video format.
Notes on CD-R and CD-RW
• This system can also play CD-Rs or CD-RWs if MP3,
WMA, and JPEG files are recorded on them with ISO
9660 format.
• This system supports “multi-session” discs (up to 20
sessions).
• This system cannot play “packet write” (UDF format)
discs. Some discs may not be played back because of
their disc characteristics, recording conditions, or
damage or stain on them.
Discs that cannot be played back
SVCD
PAL
CD
—
CD-R
—
CD-RW
—
• The following discs cannot be played back:
DVD-ROM, DVD-RAM, DVD-R/-RW (recorded in VR
format), CD-ROM, CD-I (CD-I Ready), Photo CD,
SACD, etc.
Playing back these discs will generate noise and
damage the speakers.
Damaged discs and discs in an extraordinary shape
(other than a disc of 12 cm or 8 cm) cannot be played
back.
Caution for DualDisc playback
The non-DVD side of a “DualDisc” does not comply
with the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc
on this product may not be recommended.
is a trademark of DVD Format/Logo
Licensing Corporation.
3
FS-Y1[B]_f.book Page 4 Friday, April 15, 2005 7:46 PM
About discs (continued)
Notes on all files
• The system can only recognize and play files with one
of the following extensions, which can be in any
combination of upper and lower case;
• MP3: “.MP3”, “.mp3”
• WMA: “.WMA” , “.wma”
• JPEG: “.JPG”, “.JPEG”, “.jpg”, “.jpeg”
• If a character other than single byte English characters
is used in the file name of an MP3/WMA/JPEG file, the
track/file name will not be displayed correctly.
• The system recognizes up to 150 tracks (files) per
group, 99 groups per disc, and the total number of the
tracks (files) that the system can play is 1 000.
• Some files may not be played back normally because
of their disc characteristics or recording conditions.
For MP3/WMA files
• An off-the-shelf MP3 disc may be played in an order
different from that indicated on the label attached to
the disc.
• The system supports MP3/WMA files recorded with a
bit rate of 32 – 320 kbps and a sampling frequency of
16 kHz, 22.05 kHz, 24 kHz (WMA only), 32 kHz, 44.1
kHz, or 48 kHz.
• If the tag information (album name, artist, and track
title, etc.) is recorded on a disc, it appears in the file
control display on the TV screen.
• We recommend to record each piece of material
(song) at a sample rate of 44.1 kHz and at a data
transfer rate of 128 (96 for WMA only) kbps.
• This system cannot play back files encoded with
Multiple Bit Rate (MBR). (MBR is a format to encode a
file content at several different bit rates.)
For JPEG files
• We recommend to record a file at 640 x 480 resolution.
• This system can play a baseline JPEG file, excluding
monochromatic JPEG files.
• This system can play JPEG data taken with a digital
camera conforming to the DCF (Design Rule for
Camera File System) standard (when a function is
applied such as the automatic rotation function of a
digital camera, data goes beyond the DCF standard,
so the image may not be displayed).
• If data has been processed, edited and restored with
PC image editing software, the data may not be
displayed.
• This system cannot play animations such as MOTION
JPEG, or still images (TIFF etc.) other than JPEG, and
image data with sound.
• An image with a resolution of more than 8 192 x 7 680
pixels cannot be displayed.
Disc structure
DVD VIDEO
A DVD VIDEO consists of “titles” and each title
may be divided into “chapters”.
Title 1
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2
DVD AUDIO
A DVD AUDIO consists of “groups” and each group
may be divided into “tracks”.
Some discs include a “bonus group” that requires a
password for playing (page 27).
Group 1
Track 1
Track 2
Group 2
Track 3
Track 1
Track 2
VCD/SVCD/CD
VCD, SVCD and CD consist of “tracks”.
In general, each track has its own track number.
(On some discs, each track may also be further
divided by indexes.)
Track 1
Track 2
Track 3
Track 4
Track 5
MP3/WMA [JPEG] discs
On an MP3/WMA [JPEG] disc, each still picture
(material) is recorded as a track [file]. Tracks [Files]
are usually grouped into a folder. Folders can also
include other folders, creating hierarchical folder
layers.
This unit simplifies the hierarchical construction of
a disc and manages folders by “groups”.
Group 1
Track 1
[File 1]
Track 2
[File 2]
Group 2
Group 3
Group 4
Group 5
This product can recognize up to 1 000 tracks
[files] in a disc. Also, the product can recognize up
to 150 tracks [files] per group and up to 99 groups
in a disc. Since the unit ignores the tracks [files]
whose numbers are exceeding 150 and the groups
whose numbers are exceeding 99, they cannot be
played back.
• If there is any type of files other than MP3/WMA
[JPEG] files in a folder, those files are also
counted in the total file number.
4
FS-Y1[B]_f.book Page 5 Friday, April 15, 2005 7:46 PM
Description of parts
Introduction
The numbers represent the page numbers.
Front panel
Top of the unit
See “Display
window” below.
16
16
32
32
15
14
12
16
12
11
In the door
12
BASS/TREBLE
DIMMER
3D PHONIC
FM
AM
AU X
DOWN
MULTI CONTROL
UP
26
38
15
PLAY
PAUSE
14
12
PHONES
* Connect headphones (not supplied) with a stereo mini plug. If the headphones are connected, the
speakers and subwoofer will not produce any sound.
Display window
13
18
26
27
27
13
S V C DV D - A RESUME PROGRESSIVE BONUS B.S.P.STAUTO RDS TA NEWS INFO
PRGM. RANDOM ALL 1 A-B 12 3 SLEEP A. STANDBY AHB PRO3D PHONIC
20
21
17, 22
38
40
39
32 34, 36 26
Rear panel
8
SPEAKERS
AM
EXT
AM
LOOP
CAUTION:
SPEAKER IMPEDANCE
4Ω-16Ω
AUX
10
8
10
10
R
R
L
PCM/
STREAM
9
11
L
FM75Ω
COAXIAL
ANTENNA
DVD OPTICAL
DIGITAL OUT
SUBWOOFER
OUT
COMPONENT
Y
PB
VIDEO
PR
11
S-VIDEO
11
11
These holes discharge heat
generated inside the unit.
Do not cover up these holes.
VIDEO OUT
5
FS-Y1[B]_f.book Page 6 Friday, April 15, 2005 7:46 PM
Using the remote control
The numbers represent the page numbers.
Putting the batteries in
the remote control
13, 16
12
26
7
12
7
32
FM
AM
16
38
15
16
7, 13,
14, 16
16
15, 32
12, 17
14
14
19
32
15, 17
7
7
15, 32
14
14
19
Batteries
19, 28
29
24
24
27
38, 39
38, 39
38
40
39
20
16
16
35, 36
28
24
25
13
25, 26
26
7, 15
RDS
PTY SELECT PTY SEARCH DISPLAY
33 32
22 23
10
TA/News/Info
If the range or effectiveness of the remote control
decreases, replace the batteries. Use two R6
(SUM-3)/AA(15F) type dry-cell batteries.
CAUTION
• Do not use a used battery and a new battery
together.
• Do not use different types of batteries at the
same time.
• Take out the batteries if the remote control is not
to be used for a long time. Otherwise it may
cause a leakage.
Remote control operation
When operating the remote control, point it
towards the front panel of the main unit. If the
remote control is operated from a direction that is
extremely oblique or when there is an obstacle in
the way, signals may not be transmitted.
If the remote control sensor is exposed to a strong
light such as direct sunlight, correct operation may
not be carried out.
6
FS-Y1[B]_f.book Page 7 Friday, April 15, 2005 7:46 PM
Getting
Introduction
started
This page is for when operating your TV using the
remote control of this product.
Operating the TV using
the remote control
Manufacturer
Code
Manufacturer
JVC
01
Nordmende
Akai
Blaupunkt
Daewoo
Fenner
02, 05
03
10, 31, 32
04, 31, 32
Okano
Orion
Panasonic
Philips
Fisher
05
Saba
Grundig
Hitachi
Inno-Hit
Irradio
06
07, 08
09
02, 05
Sanyo
Schneider
Sharp
Sony
Magnavox
10
Telefunken
Mitsubishi
11, 33
Thomson
Miver
Nokia
03
12, 34
Toshiba
Code
13, 14, 18,
26 – 28
09
15
16, 17
10
13, 14, 18,
26 – 28
05
02, 05
20
21 – 25
13, 14, 18,
26 – 28
13, 14, 18,
26 – 28, 30
29
NOTE
Manufacturer’s codes may be changed without notice.
You may not be able to operate a TV produced by the
manufacturer shown above.
5
Release
TV.
For TV operation
Operate the remote control by pointing it towards
the TV.
Turn ON/OFF the power.
Change channels.
Setting the manufacturer's code
1
Adjust volume.
Slide the remote control mode
selector to the TV side.
Select channels.
9
100+
*1
2
Keep pressing down
TV.
Alternates between the
previously selected channel
and the current channel.
NOTE
Keep pressing down
3
4
TV until Step 4 is complete.
Switch TV and video input.
Press ENTER.
Press number buttons (1-9, 0).
Ex.:
For a Hitachi TV: Press 0, then 7.
For a Toshiba TV: Press 2, then 9.
*1 Make sure to slide the remote control mode
selector to the TV side in advance.
NOTE
When the batteries are replaced, perform the
manufacturer's code setting again.
If there are more than one manufacturer’s codes,
try them in turn and select the one that causes the
product to work properly.
7
FS-Y1[B]_f.book Page 8 Friday, April 15, 2005 7:46 PM
Connecting up – Do not turn on the power until the connection is complete –
Connection
Connecting antennas
Connecting AM loop antenna (supplied)
1 Set up the AM loop antenna.
Connecting FM antenna (supplied)
Main unit
(rear panel)
FM antenna
FM75Ω
COAXIAL
Put the antenna up straight in the direction where
the best radio reception can be obtained, and fix
by using tape.
2
Connect antenna cords.
Main unit
(rear panel)
How to insert antenna cords
AM
EXT
AM
LOOP
Connect two antenna cords
as described above.
If the antenna cord is
covered with vinyl on the
tip, twist and pull the vinyl
off and remove.
3
Turn the AM loop antenna to the direction of the
best radio reception.
Locate the AM loop antenna as far away from
the main unit as possible.
• Do not locate the AM loop antenna on a metallic
table or close to a TV, personal computer, etc.
Otherwise it may result in bad radio reception.
7 When good radio reception cannot be
obtained with the supplied AM loop antenna
Electric wire: 3 - 5 m (commercially available)
Electric wire
Twist
AM loop
antenna
Put up an electric
wire extending
horizontally,
preferably at a high
place such as
above a window or
outdoors.
7 When good radio reception cannot be
obtained with the supplied antenna or when
using a communal antenna
Antenna cord (not
supplied)
Main unit
(rear panel)
FM75Ω
COAXIAL
or
Communal
antenna terminal
Outdoor FM antenna
(commercially
available)
Coaxial cable
Converter
(commercially
(sold separately:
available)
compatible with 300 Ω/
75 Ω)
Depending on the radio reception
conditions, an FM feeder antenna (sold
separately: compatible with 300 Ω) can
be used. In the case, a converter (not
supplied) is required.
For details of connecting a separately sold
antenna, refer to the user guide for the antenna
or converter.
AM
EXT
AM
LOOP
Main unit
(rear panel)
8
Connect the AM loop
antenna cords together.
When positioning the antenna, listen to an actual radio program (refer to “Listening to a radio broadcast” on page 32).
FS-Y1[B]_f.book Page 9 Friday, April 15, 2005 7:46 PM
Connecting up
Getting
Connection
started
Connecting speakers
There is no difference between the left and right
speakers.
Speaker terminal
Speaker cord
Speaker cord
(supplied)
SPEAKERS
Without
black line
With black
line
Speaker cord
(supplied)
Without black line
With black line
R
L
Main unit
(rear panel)
Right speaker
(rear panel)
Left speaker
(rear panel)
CAUTION
• DO NOT connect more than one speaker to one
speaker terminal.
• The speakers of this product are magnetically
shielded, but color irregularities may occur on
the TV depending on how the speakers are
installed. Keep in mind the following.
1. Turn off the main power of your TV before
installing the speakers. Wait for about 30
minutes before turning on the TV again.
2. If color irregularity occurs in pictures, keep a
distance of more than 10 cm between the TV
and the speakers.
Speaker grille can be detached.
Speaker
grille
NOTE
• Impedance of speaker that can be connected to the
main unit is within a range of 4 Ω to 16 Ω.
• In order to have a sufficient cooling effect, leave a
space of more than 1 cm between the main unit and
the speakers or other objects.
9
FS-Y1[B]_f.book Page 10 Friday, April 15, 2005 7:46 PM
Connecting up (continued) – Do not turn on the power until the connection is complete –
Connection
Connecting other devices
This page is for when connecting the main unit with
other devices.
Connecting subwoofer
With an amplifier-built-in subwoofer (not supplied), you can enjoy a more dynamic bass sound.
Refer to the manual of the subwoofer for details.
Amplifier-built-in subwoofer
(not supplied)
Audio cord (not supplied)
(If an audio cord comes with the amplifier-built-in subwoofer,
you can use the cord.)
Main unit
SUBWOOFER
OUT
When you want to hear sound from the subwoofer,
press S.WFR OUT on the remote control to display
“SUBWOOFER” on the display window on the
main unit. Each time you press the button, the
display toggles between “SUBWOOFER” and
“OFF”.
NOTE
When “SUBWOOFER” is selected, bass sound from
the left and right speakers will be automatically
lowered and the bass sound will be emitted mainly
from the subwoofer.
Connecting with a digital device
Connecting with other audio device
Input
Digital device
(MD recorder etc.)
To digital input terminal
Output
Other audio
device
Optical digital cord
(not supplied)
Output
Audio cord (not
supplied)
PCM/
STREAM
Main unit
Red
White
DVD OPTICAL
DIGITAL OUT
CAUTION
AUX
Input
R
10
L
Main unit
• For details of signals to be output, refer to page
30.
• If connecting the main unit with equipment with the
function of a Dolby Digital decoder, the setting in
“D. RANGE COMPRESSION” of “AUDIO” (page 30)
will be invalid regarding sound from the digital
audio output of the main unit.
FS-Y1[B]_f.book Page 11 Friday, April 15, 2005 7:46 PM
Connecting up
Getting
Connection
started
Connecting by using the component video
cord
Connecting with TV
Supplied composite video cord
TV
You can enjoy better quality pictures than when
using the S-Video cord.
Main unit
COMPONENT
Y
PB
VIDEO
PR
S-VIDEO
VIDEO OUT
CAUTION
Connect the main unit directly with a TV (or a
monitor) without routing through a VCR.
Otherwise it may cause picture distortion while
playing.
TV (or
monitor)
Main unit
Component video cord
(not supplied)
Blue
Green
Red
Connecting directly
Also, when connecting the main unit to a TV with
a VCR built in, there may be picture distortion
while playing.
COMPONENT
Y
PB
You can enjoy pictures of better quality using the
following cord instead of the supplied video cord.
S-VIDEO
VIDEO OUT
Main unit
Connecting by using the S-Video cord
Main unit
COMPONENT
Y
PB
S-Video cord (not
supplied)
VIDEO
PR
TV
VIDEO
PR
CAUTION
Use one of either the S-Video cord or the
component video cord. If both cords are used,
pictures may not be played properly.
S-VIDEO
VIDEO OUT
NOTE
• In order to enjoy pictures with Progressive mode
(page 26), the TV is required to have Progressive
video input.
• If the component video input jacks of your TV are
BNC type, use a plug adapter (not supplied) to
convert the plugs.
Connecting the power cord
AC outlet
Supplied power cord
Main unit
• Connect the power cord after all other
connections are complete.
• The standby lamp (on the front panel) will be lit.
11
FS-Y1[B]_f.book Page 12 Friday, April 15, 2005 7:46 PM
Playing discs
Playback
(Refer to page 17 for playing MP3/WMA and JPEG.)
page 5
1
Press
Place a disc with the label side
facing up.
• Place an 8 cm disc in to the
hollow part in the center.
AUDIO.
• The power will be turned on and the standby lamp
will go off.
• Press
AUDIO again to turn off the power.
2
Press 0OPEN/CLOSE to open the disc
tray to load a disc.
3
Press DVD/CD 3.
The disc tray will close and playback will start.
• The power will be turned on when any of PLAY
3, FM, AM, AUX, or 0 on the main unit and
DVD/CD 3, FM, AM, AUX, or 0OPEN/CLOSE
on the remote control is pressed while the power
is off.
If any button other than 0 or 0OPEN/CLOSE is
pressed, the source will also be changed (if
there is a disc loaded, playback will start).
NOTE
• A menu screen may be displayed on the TV after
starting playback of a DVD/VCD/SVCD. In this
case, select a desired item to playback by using the
following buttons on the remote control.
• Select a desired item using cursor 5/∞/2/3 and
press ENTER.
• Select a desired item using the number buttons.
• Depending on the disc, actual operation may be
different from the description.
Screens displayed on the TV when the power is turned ON.
The following messages appear depending on the status of the system.
(When FM, AM, or AUX is selected as a source, the messages do not appear.)
NOW READING
REGION CODE
ERROR!
NO DISC
OPEN
CLOSE
CANNOT PLAY THIS
DISC
12
Appears when the system is reading the disc information. Wait for a while.
Appears when the Region Code of the DVD VIDEO does not match the code
the system supports. (page 3)
Appears when no disc is loaded.
Appears when opening the disc tray.
Appears when closing the disc tray.
Appears when trying to play back an unplayable disc.
FS-Y1[B]_f.book Page 13 Friday, April 15, 2005 7:46 PM
Basic operations
Ex.: When a CD is played
S V C DV D - A
Track number
Ex.: When an MP3/WMA file is played
Display window during disc playback
Ex.: When a DVD VIDEO is played
S V C DV D - A
Track number
S V C DV D - A
To switch the display
Disc type
Chapter number
Elapsed
playing time
Press DISPLAY.
Each time you press the button, the display
indication changes temporarily as follows:
• For DVD VIDEO
Ex.: When a DVD AUDIO is played
S V C DV D - A
S V C DV D - A
Title number
Track number
Chapter number
• For DVD AUDIO
If “BONUS” or “B.S.P.” is displayed during a DVD
AUDIO playback, refer to page 27.
S V C DV D - A
Ex.: When an SVCD or VCD is played
Group
number
Track number
• For MP3/WMA
S V C DV D - A
Track number
• When playing an SVCD, the SVCD indicator
lights instead of the VCD indicator.
• PBC (Play Back Control): A signal recorded in a
VCD (version 2.0) for controlling playback. It is
possible to enjoy interactive software or software
with a search function using a menu screen
recorded in a PBC compatible VCD. To play a
disc with the PBC function OFF, carry out the
following operations.
• Designate the track number using the number
buttons while the disc is stopped.
• Designate the track number using ¢ while
the disc is stopped, and then press DVD/CD 3.
• Press RETURN to go back to the upper layer
during the PBC playback of a VCD or SVCD.
S V C DV D - A
Group
number
Track number
• For SVCD/VCD/CD
The clock time indication appears on the display
window.
• Before setting the clock (page 38), “0:00”
appears.
• When the unit is turned off, pressing DISPLAY
turns off the clock indication to save the power
consumption.
13
FS-Y1[B]_f.book Page 14 Friday, April 15, 2005 7:46 PM
Playing discs (continued)
Designate the chapter number or
track number to play during
playback.
• Refer to “How to use the number buttons” on
page 15.
To stop playback
Press 7 during playback.
To pause playback
Press 8 during playback.
To start normal playback again, press DVD/CD 3.
• For JPEG slide-show, pressing DVD/CD 3 starts
playback from the next file.
To advance picture
frame-by-frame
Press 8 during pause.
• Each time you press the button, picture will be
advanced frame-by-frame.
Select what you want to
play by using the number
buttons
NOTE
• Set the remote control mode selector to
AUDIO before using the number buttons.
• For a VCD or SVCD, this operation can
be carried out when the disc is stopped, or during
playback without the PBC function.
• For a DVD AUDIO, CD, MP3/WMA or JPEG, this
operation can also be carried out when the disc is
stopped.
• This operation may not be carried out for some
discs.
14
Fast reverse/Fast forward
search
Press 1 or ¡ during playback.
• Each time you press the button, the speed
increases ( ×2, ×5, ×10, ×20, ×60). To restore
the normal speed, press DVD/CD 3.
NOTE
• Fast reverse/Fast forward search cannot be carried
out for MP3, WMA, and JPEG.
• For a DVD VIDEO, VCD or SVCD, no sound comes
out during Fast reverse/Fast forward search.
• For a CD or DVD AUDIO, sound is intermittent
during Fast reverse/Fast forward search.
FS-Y1[B]_f.book Page 15 Friday, April 15, 2005 7:46 PM
Basic operations
Playing back from a position
10 seconds before
(One Touch Replay)
Skip to the beginning of
the selection
Press 4 or ¢ during playback*.
Press
during playback.
NOTE
• This operation may not be carried out for some
discs.
• It is not possible to go back to the previous title.
Slow Motion Playback
• Press ¢ to skip the next chapter or track.
• Press 4 once to skip back to the beginning of
the chapter or track currently being played
(except for JPEG).
to select the title
• Press GROUP/TITLE
or
or group.
• During playback of a JPEG disc, press ¢ or
cursor ∞ to play the next file, or press 4 or
cursor 5 to play the previous file.
NOTE
Press SLOW
pause.
or SLOW
during
• Each time you press the button, the playback
speed increases ( ×1/32, ×1/16, ×1/8, ×1/4,
×1/2).
• Press DVD/CD 3 to start normal playback again.
* For a VCD or SVCD, this operation can be carried
out during playback without the PBC function.
• Except for a DVD VIDEO, this operation can also be
carried out while the disc is stopped.
• This operation may not be carried out for some
discs.
NOTE
• No sound will be produced.
• The picture motion in the reverse direction may not
be smooth.
• For a VCD or SVCD, Slow Motion Playback can be
carried out in the forward direction only.
How to use the number buttons
Ex.:
5:
20:
15:
25:
Guide icons displayed on the TV screen (On-screen guide)
: Play
: Containing multi-angle views
(page 24)
: Pause
: Containing multi-audio languages
(page 24)
: Fast reverse/Fast forward search
: Containing multi-subtitle languages
(page 24)
: Slow Motion Playback (reverse/
forward directions)
: The disc cannot accept the operation you
have attempted.
15
FS-Y1[B]_f.book Page 16 Friday, April 15, 2005 7:46 PM
Playing discs (continued)
Playing audio/video files
To change the
brightness of the display
window (DIMMER)
Press DIMMER repeatedly.
• Each time you press the button, the dimmer
mode changes as follows:
AUTO DIMMER: During the video source
playback, the display window dims
and the illumination automatically
turns off.
DIMMER ON: The display window and the
illumination dim.
DISPLAY OFF: The display window and the
illumination turn off.
DISPLAY ON: Cancels the dimmer function.
• When the unit is turned off, pressing DISPLAY
turns off the clock indication to save the power
consumption.
The items above can be carried out for all sources.
Adjusting the volume
Press AUDIO VOL +/–.
NOTE
The volume can be also adjusted by turning the
VOLUME control on the main unit.
Adjusting sound quality
Bass: Press BASS +/–.
Treble: Press TREBLE +/–.
• Adjustable range: –5 to +5
Turning off the sound
temporarily (MUTING)
Press MUTING.
• No sound will come out from the speakers,
headphones and the subwoofer.
• Press MUTING again to restore the sound.
When the power is turned off once and turned
on again, the sound will be restored.
16
NOTE
Set the remote control mode selector to
AUDIO before using the number buttons.
FS-Y1[B]_f.book Page 17 Friday, April 15, 2005 7:46 PM
Advanced operations
5
Playback
Press DVD/CD 3 or ENTER.
NOTE
Display of an MP3/WMA disc is described here as
an example.
For a JPEG disc, read “track” as “file”.
• GROUP/TITLE
can also be used in Step 2.
• The number buttons can also be used in Step 4. In
this case, Step 5 is not needed. (For how to use the
number buttons, refer to page 15.)
• 4 or ¢ can also be used in Step 4. In this case,
Step 5 is not needed.
NOTE
When playing a disc containing both MP3/WMA and
JPEG files, set one of them to be played, then turn on
the system again (page 29).
1
Repeat playback
Load a disc.
Current group /total
group number
Playback mode (PROGRAM,
RANDOM, REPEAT)
Tag information (for
MP3/WMA)
Current group
Elapsed playing time of
current track (for MP3/
WMA)
Current track
(file)
Current track (file) /
total track (file)
number on current
group
Total track (file)
number on disc
Playback status
2
Press cursor 5/∞ to select a
group.
3
Press cursor 3 to move to the
track list.
1
Press REPEAT.
• Each time you press the button, the Repeat
mode and its indication change as follows:
Repeat items
On the TV
Current track
(MP3/WMA only)
REPEAT
TRACK
Current group
REPEAT
GROUP
Entire disc
REPEAT
ALL
Cancel
No indication
Current track
during Program/
Random play
(MP3/WMA only)
REPEAT
STEP
All tracks during
Program/Random
play (MP3/WMA
only)
REPEAT
ALL
2
On the display
window
Press DVD/CD 3.
NOTE
• The Repeat types can be changed during playback.
• The Repeat mode will be automatically canceled if
there is a file that cannot be played (page 3).
• Press cursor 2 to go back to the group list.
4
Press cursor 5/∞ to select a
track.
Slide-Show Playback
• In Step 5, for a JPEG disc, when DVD/CD 3 is pressed, files will be continuously played from the
selected file (Slide-Show Playback), and when ENTER is pressed, only a selected file will be played.
• Display time for a file in Slide-Show Playback is about 3 seconds.
• When all files are played through, the playback will be automatically stopped.
17
FS-Y1[B]_f.book Page 18 Friday, April 15, 2005 7:46 PM
Resume Playback
This system can store the stop point, and when
you start playback again by pressing DVD/CD 3
(even while on standby), it starts from the position
where you have stopped—Resume Play. The
RESUME indicator lights on the display window
when you stop playback.
How to suspend playback
Perform any of the following operations during
playback.
Press 7 once.*
Press
AUDIO to turn off the power.
Change the source to FM, AM or AUX.*
* Even if the power is turned off by pressing
AUDIO after this, the position where playback
has been stopped will be stored.
To start playback from the stored
position
NOTE
Press DVD/CD 3.
Set the remote control mode selector to
AUDIO before using the number buttons.
NOTE
• This function does not work in Program Playback or
Random Playback.
• The position where playback starts again may be a
little different from the stopped position.
• When a disc menu is displayed, the Resume
function may not work.
• The audio language, the subtitle language and the
angle at that time are stored as well as the stopped
position.
• The stored position will be cleared if the disc tray is
opened. Further, if 7 is pressed during playback,
“RESUME” will be displayed. If 7 is pressed again,
the stored information will be cleared.
• At the time of purchase, Resume is set to ON.
Resume can be set to OFF (page 30).
18
FS-Y1[B]_f.book Page 19 Friday, April 15, 2005 7:46 PM
Select the scene to be played
Advanced operations
NOTE
*1 For a VCD and SVCD, this operation can be carried
out only when the PBC function is off.
• This operation cannot be carried out for a disc
without a menu screen.
• Playback may start for some discs without pressing
ENTER.
Designate the time
(Time search)
1
Press ON SCREEN twice during
playback*2.
The menu bar will be displayed (page 28).
2
Press cursor 2 /3 to select
.
3
4
Press ENTER.
NOTE
Input the time*3 using the
number buttons (1-9, 0).
Ex.: When you want to play a DVD VIDEO
from the position of (0 hour) 23
minutes 45 seconds, press the
buttons in the order:
Set the remote control mode selector to
AUDIO before using the number buttons.
Select the scene from
the menu
2
Press MENU or TOP MENU
while the disc is stopped or
during playback*1.
• The disc menu screen will be displayed.
• Only TOP MENU can be used for DVD
AUDIOs.
2
Press cursor 5/∞/2/3 (only
for a DVD VIDEO or DVD AUDIO)
or the number buttons to select
the scene to be played.
• Refer to “How to use the number buttons”
(page 15).
• When the menu screen has a couple of
pages, press 4 or ¢ to change the
page (only for a VCD and SVCD).
3
4
5
• If you input wrong numbers, press cursor 2
to delete the numbers and re-input.
5
1
3
Press ENTER.
To delete the menu bar, press ON SCREEN.
NOTE
• This function does not work for a DVD VIDEO with
no time information recorded.
• This function does not work during Program or
Random Playback.
*2 For a VCD and an SVCD, the operation can be
carried out when the disc is stopped or during
playback without the PBC function.
*3 Time search for a DVD VIDEO is from the beginning
of the title, for a DVD AUDIO from the beginning of
the track being played. Time search for a VCD, an
SVCD and a CD is as follows:
• When the disc is stopped, time search is from the
beginning of the disc.
• When the disc is being played, time search is
within the track currently being played.
Press ENTER.
19
FS-Y1[B]_f.book Page 20 Friday, April 15, 2005 7:46 PM
Program Playback/Random Playback
Play the disc in the
desired order
(Program Playback)
It is possible to program a maximum of 99 chapters
or tracks. The same chapter or track can be
programmed more than once.
1
While the disc is stopped, press
PLAY MODE repeatedly to
display “PROGRAM” on the
display window on the main
unit.
TV screen
Program
screen
2
NOTE
Set the remote control mode selector to
AUDIO before using the number buttons.
20
Create a program following the
description on the TV screen.
Refer to “How to use the number buttons”
(page 15).
• The input content varies depending on the
disc type.
• DVD VIDEO:
Titles and chapters
• VCD, SVCD, CD: Tracks
• DVD AUDIO, MP3/WMA:
Groups and tracks
• To select a DVD AUDIO bonus group, carry
out the operations of “Playing the Bonus
Group” on page 27 in advance to erase the
display “BONUS”.
• If the input number of chapters or tracks is
greater than 99, “MEM FULL” will be
displayed.
• In the case of a VCD, SVCD or CD, when
the total playback time reaches 9 hours 59
minutes 59 seconds, “--:--” will be displayed
on the display window (it is possible to
continue programming).
FS-Y1[B]_f.book Page 21 Friday, April 15, 2005 7:46 PM
Advanced operations
To program on the display window on the main
unit, operate as follows:
(1) Select a title/group using the number
buttons.
(2) Designate a chapter/track number using the
number buttons.
• Refer to “How to use the number buttons”
(page 15).
• The program number will be displayed on
the lower display window (Ex.: “P2”).
Playing the disc in a
random order
(Random Playback)
1
(3) Repeat the above operations (1) and (2) to
complete the program. Then, advance to
Step 3.
NOTE
• The group/title number flashes on the display
window after making each program step.
• Only for a DVD VIDEO, DVD AUDIO, VCD, or an
MP3/WMA: If you press ENTER instead of
designating a track/chapter number, “ALL” is
displayed and all of the tracks/chapters in the
selected group/title are programmed.
3
Press DVD/CD 3.
• To resume normal playback, press PLAY
MODE repeatedly to show the playback
indication on the display window on the
main unit while the disc is stopped. The
program content will not be erased.
• The following operations erase the program
content:
• Press CANCEL repeatedly (Programs
will be erased one by one)
• Press 7 while the disc is stopped
• Open the disc tray
• Turn off the power
Press PLAY MODE repeatedly
to display “RANDOM” on the
display window on the main unit
while the disc is stopped.
• “RANDOM” will also be displayed on the TV
screen.
2
Press DVD/CD 3.
• The same chapter or track will not be
played twice.
• To resume normal playback, press PLAY
MODE repeatedly to show the playback
indication on the display window on the
main unit while the disc is stopped.
• Random Playback will also be canceled by
carrying out the following operations:
• Open the disc tray
• Turn off the power
• The previous track will not be returned to
even if 4 is pressed repeatedly during
Random Playback (the beginning of the
current chapter or track will be returned to).
21
FS-Y1[B]_f.book Page 22 Friday, April 15, 2005 7:46 PM
Repeat Playback
Refer to page 17 for Repeat Playback of MP3 and
JPEG files.
For DVD AUDIO
Repeat items
On the TV
Current track
On the display
window
TRACK
Current group
GROUP
Cancel
OFF
For CD/VCD/SVCD
Repeat items
Current track
All tracks
Cancel
On the TV
On the display
window
TRACK
ALL
OFF
NOTE
Playing the title/chapter/
group/track/all tracks
repeatedly (REPEAT)
Press REPEAT during playback.
• Each time you press the button, the Repeat
mode and its indication change as follows:
For DVD VIDEO
Repeat items
Current chapter
Current title
Cancel
On the TV
On the display
window
• For a VCD and SVCD, the operation can be carried
out only when the disc is stopped or during playback
without the PBC function.
• It is possible to set Repeat mode on the menu bar.
For how to operate, refer to “Playing the designated
part repeatedly (A-B Repeat Playback)”(page 23).
• For a DVD VIDEO and DVD AUDIO, if the source is
switched to FM, AM, or AUX, the Repeat mode will
be canceled.
Repeat Playback during Program or
Random Playback
Repeat items
Current chapter/
track
OFF
STEP
or REPEAT
STEP
CHAP
TITLE
On the TV
All tracks during
Program/Random
play
Cancel
ALL
or REPEAT
ALL
OFF
or no
indication
22
On the display
window
FS-Y1[B]_f.book Page 23 Friday, April 15, 2005 7:46 PM
Advanced operations
Playing the designated
part repeatedly
(A-B Repeat Playback)
1
Press ON SCREEN twice during
playback.
The menu bar (page 28) will be displayed.
2
Press cursor 2/3 to select
OFF .
3
4
Press ENTER.
Press cursor 5/∞ to display
OFF
A B
.
Other Repeat modes can be selected here.
For other Repeat modes, refer to “Playing the
title/chapter/group/track/all tracks repeatedly
(REPEAT)” (page 22).
5
Press ENTER at the start point
of the part to be repeated
(designating A point).
• The icon on the menu bar will be
6
A-
.
Press ENTER at the end point of
the part to be repeated
(designating B point).
• The icon on the menu bar will be
A-B
and the part between A and B points will be
played repeatedly.
• A-B Repeat Playback will be canceled by
carrying out the following operations:
• Press 7.
• Select
A-B and press ENTER twice.
NOTE
• A-B Repeat Playback is possible only within the
same title or track. A-B Repeat Playback cannot be
carried out during PBC playback, Program
Playback, Random Playback and Repeat Playback.
• You can do the A-B Repeat Playback using the
REPEAT A-B button on the remote control.
23
FS-Y1[B]_f.book Page 24 Friday, April 15, 2005 7:46 PM
Other convenient functions
Selecting the audio
language
1
Press AUDIO during playback of
a disc containing several audio
languages.
Ex.:
• Each time you press the button, the audio
language will be alternated. Also, the audio
language can be changed by pressing
cursor 5/∞.
• For a language code such as “AA”, refer to
“Language codes” (page 42).
• “ST”, “L” and “R” displayed when playing a
VCD or SVCD respectively represent
“Stereo”, “Left sound” and “Right sound”.
Selecting the subtitles
(only for moving image)
1
Press SUBTITLE during
playback of a disc containing
subtitles in several languages.
Ex.:
TV screen
2
TV screen
Wait for a few seconds or press
ENTER to go off the window.
NOTE
• Each time you press the button, the subtitle
will be alternated between ON and OFF.
2
Press cursor 5/∞ to select a
subtitle language.
• For a language code such as “AA”, refer to
“Language codes” (page 42).
• The manner of displaying subtitle
languages may be different depending on
the disc.
3
It is also possible to operate by using the menu bar
(page 28).
Selecting a view angle
(only for moving image)
1
Wait for a few seconds or press
ENTER to go off the window.
Press ANGLE during playback
of a scene containing multi-view
angles.
Ex.:
TV screen
NOTE
• It is also possible to operate by using the menu bar
(page 28).
• For an SVCD, each time you press SUBTITLE in
Step 1, the subtitle type and OFF will be alternated.
• Each time you press the button, the angle
will be alternated. Also, the angle can be
changed by pressing cursor 5/∞.
2
Wait for a few seconds or press
ENTER to go off the window.
NOTE
It is also possible to operate by using the menu bar
(page 28).
24
FS-Y1[B]_f.book Page 25 Friday, April 15, 2005 7:46 PM
Advanced operations
Enlarging the picture
(ZOOM)
2
• It is recommended to select “NORMAL”
usually, or “CINEMA” in a dark room. When
either “NORMAL” or “CINEMA” is selected,
go to Step 7.
• When either “USER 1” or “USER 2” is
selected, the adjustment can be carried out
in detail in the operations after Step 3.
(only for moving image)
1
Press ZOOM during playback or
while paused.
• Each time you press the button, the picture
magnification will be changed.
• (For a JPEG) You cannot change the
picture magnification during slide-show
playback.
2
3
Press cursor 5/∞ to select an
item to be adjusted.
4
Press ENTER.
Ex.:
Select the portion you want to
see by using cursor 5/∞/2/3.
• To resume normal playback, select “ZOOM
OFF” in Step 1.
Adjusting the picture
quality (VFP)
Press VFP during playback or
while paused.
The current setting will be displayed on the
TV screen.
TV screen
GAMMA
5
Press cursor 5/∞ to change the
value.
6
Press ENTER.
To adjust other items, go back to Step 3.
7
1
Press cursor 2/3 to select VFP
mode.
Press VFP to go off the window.
NOTE
• If no operation is made for several seconds during
the procedure, the settings made so far will be
automatically stored.
• “VFP” is an abbreviation of “Video Fine Processor”.
• GAMMA: Adjust this if the neutral color is
bright or dark. The brightness of dark and
bright portion is maintained.
• BRIGHTNESS: Adjust this if the picture is
bright or dark on the whole.
• CONTRAST: Adjust this if the far and near
position is unnatural.
• SATURATION: Adjust this if the picture is
whitish or blackish.
• TINT: Adjust this if the appearance of flesh
tone is unnatural.
• SHARPNESS: Adjust this if the picture is
indistinct.
25
FS-Y1[B]_f.book Page 26 Friday, April 15, 2005 7:46 PM
Other convenient functions (continued)
Adjusting playback level
(DVD LEVEL)
The audio of a DVD VIDEO may be recorded at a
lower level (volume) than for other types of disc. If
the difference is not to your liking, adjust the DVD
Level.
1
Press DVD LEVEL during
playback.
• Each time you press the button, the level
will be alternated among “NORMAL”,
“MIDDLE” and “HIGH”.
• Select the level while listening to the sound
played.
NOTE
Creating realistic sound
(3D PHONIC)
The two speakers produce an effect resembling
surround-sound.
1
Press 3D PHONIC during
playback.
Ex.:
TV screen
3D PHONIC
• Each time you press the button, the 3D
PHONIC will be alternated as follows:
ACTION
: Suitable for action movies,
sport programs or other lively
programs.
DRAMA
: You can relax with a natural
atmosphere.
Enjoying better pictures
(SCAN MODE)
In the Progressive mode, better pictures can be
enjoyed.
CAUTION
• In order to enjoy pictures in the Progressive
mode, the following requirements should be met:
• There must be a component video input terminal
on the TV set connected to the main unit.
• The main unit and the TV set must be
connected using a component video cord
(page 11).
When the above requirements are not satisfied,
leave the main unit in the Interlace mode. If the
Progressive mode is set, pictures may be distorted.
Press and hold SCAN MODE for 4
seconds when there is no disc loaded
or while the disc is stopped.
THEATER : You can enjoy the sound effect
as if you were watching the
movie in a theater.
• Each time you press and hold the button, the
scan mode alternates between the
“PROGRESSIVE” mode and the “INTERLACE”
mode.
OFF
NOTE
: Cancels 3D PHONIC (initial
setting).
• While 3D PHONIC is activated, “3D
PHONIC” appears and the 3D PHONIC
indicator lights on the display window.
NOTE
• 3D PHONIC is effective for the speakers and
headphones.
• When noise is produced or sound is distorted, set
3D PHONIC to “OFF”.
• You cannot operate some DVD AUDIO discs.
26
• DVD Level is effective only for playback of a DVD
VIDEO.
• Even if the DVD Level is changed, the output level
from the digital audio output terminal will not be
changed.
Progressive mode:
All scanned lines will be displayed at once. Pictures
of higher resolution than those in the Interlace mode
can be realized.
Interlace mode:
This is a conventional image method. Half of the
scanned lines displayed in the Progressive mode
will appear, alternating with the other half.
FS-Y1[B]_f.book Page 27 Friday, April 15, 2005 7:46 PM
Functions specific to DVD AUDIO
Advanced operations
Playing the Bonus Group
There are some DVD AUDIO discs with a special
group, called “Bonus Group”, recorded.
NOTE
This operation can be carried out when “BONUS” is lit
on the display window on the main unit.
1
Press GROUP/TITLE
repeatedly during playback to
select a bonus group.
“KEY_ _ _ _” appears on the TV screen, and
on the display window on the main unit.
• The bonus group is usually recorded as the
last group.
2
Press the number buttons to
enter a pin code (4 digits).
The method of getting a pin code may be
different depending on the disc.
3
Press ENTER.
• When a correct pin code is entered,
“BONUS” disappears and the playback of
the bonus group starts.
• If an incorrect pin code is entered, try
entering a correct pin code again.
Browsable Still Pictures
(B.S.P.)
NOTE
Set the remote control mode selector to
AUDIO before using the number buttons.
There are some DVD AUDIO discs with still
pictures recorded. Among the still pictures, there
are pictures called B.S.P. (Browsable Still
Pictures). With these pictures, it is possible to
switch a picture as if turning over pages.
NOTE
This operation can be carried out when “B.S.P.” is lit
on the display window on the main unit.
1
Press PAGE during playback.
Each time you press the button, the still picture
will be switched over. It is also possible to
switch the picture using cursor 5/∞.
Ex.:
2
TV screen
Wait for a few seconds or press
ENTER to go off the window.
27
FS-Y1[B]_f.book Page 28 Friday, April 15, 2005 7:46 PM
Using the menu bar
Select this to change time information
displayed on the display window on the
main unit and the status bar. Each time
ENTER is pressed, the display will be
alternated.
DVD VIDEO/DVD AUDIO (operating
during playback)
TOTAL : Elapsed playing time of current title/
group.
T.REM : Remaining time of current title/group.
TIME : Elapsed playing time of current
chapter/track.
REM : Remaining time of current chapter/track.
CD (operating during playback)/VCD/
SVCD
TIME : Elapsed playing time of current
track.
REM : Remaining time of current track.
TOTAL : Elapsed playing time of disc.
T.REM : Remaining time of disc.
TIME
Time display
selection
See page 22.
Repeat mode
See page 19.
Time search
NOTE
• Set the remote control mode selector to
AUDIO before using the number buttons.
• This operation can be carried out when
there is a disc loaded. There are some functions that
may not work while the disc is stopped.
1
CHAP.
/
TRACK
Chapter search
(DVD VIDEO)/Track
search (DVD
AUDIO)
Press ON SCREEN twice.
The status bar and the menu bar will appear
on the TV screen.
Select a chapter/track. Press the
number buttons to input the chapter/
track number and press ENTER.
Ex.:
5:
5
24:
2
4
See page 24.
Audio language/
Audio (DVD VIDEO/
DVD AUDIO/VCD/
SVCD)
Status bar
See page 24.
Subtitle language
(DVD VIDEO/SVCD)
Menu bar
The above is an example for a DVD VIDEO.
2
3
Press cursor 2/3 to select an
item to be operated.
Press ENTER.
• The selected function can be set. For the
setting content, refer to the following
“Functions list”.
• The currently active function shows.
• To delete the menu bar, press ON
SCREEN.
Functions list
For the functions with no special description for the
operations, press cursor 5/∞ to select, and press
ENTER to determine.
See page 24.
View angle (DVD
VIDEO/DVD AUDIO)
Switch the still pictures (B.S.P.) recorded
on a DVD AUDIO disc (page 27).
PAGE
Page switch (DVD
AUDIO)
Information displayed on the status bar
DVD VIDEO/DVD AUDIO (the example below is for
a DVD VIDEO)
Transfer rate
(only for DVD VIDEO)
DVD VIDEO:
Current title number
DVD AUDIO:
Current group number
Time Playback status
DVD VIDEO:
Current chapter number
DVD AUDIO:
Current track number
VCD/SVCD/CD (the example below is for a CD)
Playback mode
Time Playback status
Current track number
28
FS-Y1[B]_f.book Page 29 Wednesday, April 20, 2005 7:23 PM
Preferences
Advanced operations
NOTE
The playback status mark has the same meaning of
the mark on the On-screen guide (page 15).
• For a language code such as “AA”, refer to the
“Language codes ” (page 42).
Items
Contents
MENU LANGUAGE
Select the language for the DVD VIDEO menu.
AUDIO
LANGUAGE
Select the audio language for the DVD VIDEO.
SUBTITLE
Select the subtitle language for the DVD
VIDEO.
ON SCREEN
LANGUAGE
Select the language displayed on the
preference screens.
PICTURE
Items
Contents (
MONITOR
TYPE
Select a display method suitable for your TV.
16 : 9:
Select this when the aspect ratio of your wide
TV is fixed to 16:9 (when playing a DVD
VIDEO recorded at 4:3, the system
automatically adjusts the screen width of the
output signal).
The initial settings of the system can be changed
according to the environment the system is used
in.
4 : 3 LB (Letter Box) :
Select this when the aspect ratio of your TV is
conventional 4:3. While viewing a wide screen
picture, the black bars appear on the top and
bottom of the screen.
NOTE
• Set the remote control mode selector to
AUDIO before using the number buttons.
• The top and bottom of the preference
screen may not be displayed on a wide TV. Adjust
the picture size on the TV.
4 : 3 PS (Pan Scan):
Select this when the aspect ratio of your TV is
conventional 4:3. While viewing a wide screen
picture, the left and right edges of the picture
will not be shown on the screen. (If the disc is
not compatible with Pan Scan, the picture will
be displayed at the Letter Box ratio.)
Basic operations
Press SET UP while the disc is
stopped or no disc is loaded (“NO
DISC” is displayed).
• The following screen will be displayed on
the TV.
PICTURE
SOURCE
Select an item suitable to the video source.
AUTO:
The video source type (a video or film) is
automatically selected.
FILM:
Select this item when you want to view a film
or video recorded with the progressive scan
method.
VIDEO:
Select this item when you want to view a
normal video.
SCREEN
SAVER
Select the Screen Saver mode between ON /
OFF (Screen Saver activates when there is
no operation made for about 5 minutes since
a still picture was last displayed).
FILE TYPE
If there are both MP3/WMA and JPEG files on
a disc, you can select which files to play.
AUDIO :
Select this item when you want to play back
MP3/WMA files.
STILL PICTURE:
Select this item when you want to play back
JPEG files.
LANGUAGE
MENU LANGUAGE
ENGLISH
AUDIO LANGUAGE
ENGLISH
SUBTITLE
ENGLISH
ON SCREEN LANGUAGE
ENGLISH
• Proceed with operations by following the
description on the TV screen.
LANGUAGE
: initial setting)
NOTE
• If the selected language is not recorded on the disc,
the optimum language set for the disc will be
displayed.
29
FS-Y1[B]_f.book Page 30 Friday, April 15, 2005 7:46 PM
Preferences (continued)
AUDIO
Items
Contents (
DIGITAL
AUDIO
OUTPUT
OTHERS
: initial setting)
Items
Contents (
Select an output signal type from the
following in accordance with the device
connected to the digital audio output
terminal (AV amplifier, etc.). (See the list
below for the preference items and output
signal.)
RESUME
Select ON /OFF. (page 18)
ON
SCREEN
GUIDE
Select ON /OFF. (page 15)
PCM ONLY:
Device corresponding only to linear PCM.
PARENTAL
LOCK
Set the Parental Lock function to cut off
violent scenes or replace the scenes with
others. (This is effective only for discs
equipped with the Parental Lock function.)
DOLBY DIGITAL/PCM:
Dolby digital decoder or a device having
the same function.
STREAM/PCM :
DTS/Dolby digital decoder or a device
having the same function.
DOWN MIX
Switch signal from the digital output
terminal of the DVD VIDEO according to
the connected device. Select this when
Digital Audio Output is set to “PCM ONLY”.
DOLBY SURROUND:
A Dolby Pro Logic decoder-built-in device.
STEREO :
An ordinary device.
• When 3D PHONIC is activated, Down
Mix does not work.
D (Dynamic).
RANGE
COMPRESSION
: initial setting)
COUNTRY CODE (page 31):
Select your country.
SET LEVEL:
The restriction is stricter as the number
becomes smaller. “NONE” is no restriction.
PASSWORD (essential):
Enter four-digit number as your password
using the number buttons (1-9, 0) every
time. (Enter “8888” if you forget your
password.)
The password is required at the time of
playback.
• If you enter a wrong password three
times, “EXIT” will be automatically
selected.
To make adjustments for the difference
between a high volume and a low volume
when playing back with low volume (only
for a DVD recorded with Dolby digital).
AUTO :
D. Range Compression automatically
works.
ON:
D. Range Compression always works.
List of relationships of DIGITAL AUDIO OUTPUT preference items and output signal
Playback disc
STREAM/PCM
48 kHz, 16/20/24 bits
Linear PCM DVD VIDEO
96 kHz linear PCM DVD VIDEO
DIGITAL AUDIO OUTPUT
DOLBY DIGITAL/PCM
PCM ONLY
48 kHz, 16 bits stereo linear PCM
48/96/192 kHz,
16/20/24 bits linear PCM DVD AUDIO
44.1/88.2/176.4 kHz,
16/20/24 bits linear PCM DVD AUDIO
DTS DVD VIDEO
DOLBY DIGITAL DVD VIDEO/
DVD AUDIO
CD/VCD/SVCD
DTS CD
MP3/WMA disc
44.1 kHz, 16 bits stereo linear PCM
DTS bit stream
48 kHz, 16 bits stereo linear PCM
48 kHz, 16 bits stereo
DOLBY DIGITAL bit stream
linear PCM
44.1 kHz, 16 bits stereo linear PCM/48kHz, 16 bits linear PCM
DTS bit stream
44.1 kHz, 16 bits linear PCM
32/44.1/48 kHz, 16 bits stereo linear PCM
NOTE
• For a DVD VIDEO: There is a 20 bit or 24 bit output for DVD VIDEO without content protection set.
• For a DVD AUDIO: There is no output for DVD AUDIO with content protection set.
30
FS-Y1[B]_f.book Page 31 Friday, April 15, 2005 7:46 PM
Country/Area codes
AD
AE
AF
AG
AI
AL
AM
AN
AO
AQ
AR
AS
AT
AU
AW
AZ
BA
BB
BD
BE
BF
BG
BH
BI
BJ
BM
BN
BO
BR
BS
BT
BV
BW
BY
BZ
CA
CC
CF
CG
CH
CI
CK
CL
CM
CN
CO
CR
CU
CV
CX
CY
CZ
DE
DJ
DK
DM
DO
DZ
EC
EE
EG
EH
ER
Andorra
United Arab Emirates
Afghanistan
Antigua and Barbuda
Anguilla
Albania
Armenia
Netherlands Antilles
Angola
Antarctica
Argentina
American Samoa
Austria
Australia
Aruba
Azerbaijan
Bosnia and
Herzegovina
Barbados
Bangladesh
Belgium
Burkina Faso
Bulgaria
Bahrain
Burundi
Benin
Bermuda
Brunei Darussalam
Bolivia
Brazil
Bahamas
Bhutan
Bouvet Island
Botswana
Belarus
Belize
Canada
Cocos (Keeling)
Islands
Central African
Republic
Congo
Switzerland
Côte d’Ivoire
Cook Islands
Chile
Cameroon
China
Colombia
Costa Rica
Cuba
Cape Verde
Christmas Island
Cyprus
Czech Republic
Germany
Djibouti
Denmark
Dominica
Dominican Republic
Algeria
Ecuador
Estonia
Egypt
Western Sahara
Eritrea
ES
ET
FI
FJ
FK
FM
FO
FR
FX
GA
GB
GD
GE
GF
GH
GI
GL
GM
GN
GP
GQ
GR
GS
GT
GU
GW
GY
HK
HM
HN
HR
HT
HU
ID
IE
IL
IN
IO
IQ
IR
IS
IT
JM
JO
JP
KE
KG
KH
KI
KM
KN
KP
KR
KW
KY
KZ
LA
LB
Spain
Ethiopia
Finland
Fiji
Falkland Islands
(Malvinas)
Micronesia
(Federated States of)
Faroe Islands
France
France, Metropolitan
Gabon
United Kingdom
Grenada
Georgia
French Guiana
Ghana
Gibraltar
Greenland
Gambia
Guinea
Guadeloupe
Equatorial Guinea
Greece
South Georgia and
the South Sandwich
Islands
Guatemala
Guam
Guinea-Bissau
Guyana
Hong Kong
Heard Island and
McDonald Islands
Honduras
Croatia
Haiti
Hungary
Indonesia
Ireland
Israel
India
British Indian Ocean
Territory
Iraq
Iran (Islamic Republic of)
Iceland
Italy
Jamaica
Jordan
Japan
Kenya
Kyrgyzstan
Cambodia
Kiribati
Comoros
Saint Kitts and Nevis
Korea, Democratic
People’s Republic of
Korea, Republic of
Kuwait
Cayman Islands
Kazakhstan
Lao People’s
Democratic Republic
Lebanon
Advanced operations
LC
LI
LK
LR
LS
LT
LU
LV
LY
MA
MC
MD
MG
MH
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
MW
MX
MY
MZ
NA
NC
NE
NF
NG
NI
NL
NO
NP
NR
NU
NZ
OM
PA
PE
PF
PG
PH
PK
PL
PM
PN
PR
PT
PW
PY
QA
RE
RO
RU
RW
SA
SB
SC
Saint Lucia
Liechtenstein
Sri Lanka
Liberia
Lesotho
Lithuania
Luxembourg
Latvia
Libyan Arab
Jamahiriya
Morocco
Monaco
Moldova, Republic of
Madagascar
Marshall Islands
Mali
Myanmar
Mongolia
Macau
Northern Mariana
Islands
Martinique
Mauritania
Montserrat
Malta
Mauritius
Maldives
Malawi
Mexico
Malaysia
Mozambique
Namibia
New Caledonia
Niger
Norfolk Island
Nigeria
Nicaragua
Netherlands
Norway
Nepal
Nauru
Niue
New Zealand
Oman
Panama
Peru
French Polynesia
Papua New Guinea
Philippines
Pakistan
Poland
Saint Pierre and
Miquelon
Pitcairn
Puerto Rico
Portugal
Palau
Paraguay
Qatar
Réunion
Romania
Russian Federation
Rwanda
Saudi Arabia
Solomon Islands
Seychelles
SD
SE
SG
SH
SI
SJ
SK
SL
SM
SN
SO
SR
ST
SV
SY
SZ
TC
TD
TF
TG
TH
TJ
TK
TM
TN
TO
TP
TR
TT
TV
TW
TZ
UA
UG
UM
US
UY
UZ
VA
VC
VE
VG
VI
VN
VU
WF
WS
YE
YT
YU
ZA
ZM
ZR
ZW
Sudan
Sweden
Singapore
Saint Helena
Slovenia
Svalbard and Jan
Mayen
Slovakia
Sierra Leone
San Marino
Senegal
Somalia
Suriname
Sao Tome and Principe
El Salvador
Syrian Arab Republic
Swaziland
Turks and Caicos
Islands
Chad
French Southern
Territories
Togo
Thailand
Tajikistan
Tokelau
Turkmenistan
Tunisia
Tonga
East Timor
Turkey
Trinidad and Tobago
Tuvalu
Taiwan
Tanzania, United
Republic of
Ukraine
Uganda
United States Minor
Outlying Islands
United States
Uruguay
Uzbekistan
Vatican City State
(Holy See)
Saint Vincent and the
Grenadines
Venezuela
Virgin Islands (British)
Virgin Islands (U.S.)
Viet Nam
Vanuatu
Wallis and Futuna
Islands
Samoa
Yemen
Mayotte
Yugoslavia
South Africa
Zambia
Zaire
Zimbabwe
31
FS-Y1[B]_f.book Page 32 Friday, April 15, 2005 7:46 PM
Listening to a radio broadcast
Selecting a station
1
2
Press FM or AM.
Press 4/¢ to select the
station (frequency).
Automatic tuning:
Hold down 4/¢ until the system starts
searching, and then release the button. (The
AUTO indicator lights while searching.)
When a station of sufficient signal strength is
tuned in to, the system stops searching
automatically.
To stop searching manually, press 4/¢.
Manual tuning:
Each time you press 4/¢, the frequency
changes.
• When an FM stereo program is received,
the ST (Stereo) indicator lights.
NOTE
If the stereo FM program currently tuned in to is noisy,
you can improve the reception by pressing FM MODE
to switch to the monaural mode. If you press FM
MODE again, or tune in to another station, the
receiving mode returns automatically to the stereo
mode.
NOTE
Set the remote control mode selector to
AUDIO before using the number buttons.
32
FS-Y1[B]_f.book Page 33 Friday, April 15, 2005 7:46 PM
Tuning in to a preset station
Listening to radio
3
Select the number you want to
store by pressing number
buttons while “MEMORY” is
flashing.
• You can also select the number by using the
number buttons.
• Refer to “How to use the number buttons”
(page 15).
4
Press MEMORY while the
selected number is flashing.
“STORED” appears on the display window
and the selected station is stored.
NOTE
• Storing a new station to a used number erases the
previously stored station.
• After storing new stations, do not unplug the AC
power cord to turn off the system. If you do so, the
new preset stations will be cleared.
Tuning in to a preset
station
Presetting stations in the system allows you to
easily tune in to a station.
NOTE
Set the remote control mode selector to
AUDIO before using the number buttons.
1
Press FM or AM to select either
FM or AM (MW).
2
Press the number buttons to
select the memory number of a
station you want to tune in to.
Refer to “How to use the number buttons”
(page 15).
You can also select by pressing 1/¡.
Presetting stations
The system stores up to 30 FM stations and up to
15 AM (MW) stations.
1
Select a station you want to
store (page 32 for how to
select).
2
Press MEMORY.
“MEMORY” is flashing on the display window
for a while.
33
FS-Y1[B]_f.book Page 34 Friday, April 15, 2005 7:46 PM
Using the RDS
To show the RDS signals information
Using the RDS (Radio
Data System) when
receiving FM stations
RDS allows FM stations to send an additional
signal along with their regular program signals. For
example, the stations send their station names, as
well as information about what type of program
they broadcast, such as sports or music, etc.
Press RDS DISPLAY while listening
to an FM station.
Each time you press the button, the indication on
the display window changes.
While searching, “PS”
appears and then the station
names will be displayed.
“NO PS” appears if no signal
is sent.
When tuned in to an FM station which provides the
RDS service, the RDS indicator lights up on the
display window.
While searching, “PTY”
appears and then the type of
the broadcast program will be
displayed. “NO PTY” appears
if no signal is sent.
With the system, you can receive the following
types of RDS signals:
PS
(Program Service)
Shows commonly
known station names.
PTY
(Program Type)
Shows types of broadcast programs.
RT
(Radio Text)
Shows text messages
the station sends.
Enhanced Other
Network
See page 36.
NOTE
• RDS is not available for AM (MW) broadcasts.
• RDS may not operate correctly if the station tuned is
not transmitting RDS signal properly or if the signal
strength is weak.
34
While searching, “RT”
appears and then text messages the station sends will
be displayed. “NO RT”
appears if no signal is sent.
Frequency
Station frequency (non-RDS
service).
About characters shown on the display
window
When PS, PTY, or RT signals appear on the
display window, some special characters and
marks may not be displayed correctly.
NOTE
If searching finishes at once, “PS”, “PTY”, and “RT” will
not appear on the display window.
FS-Y1[B]_f.book Page 35 Friday, April 15, 2005 7:46 PM
Listening to radio
Searching for a program by PTY codes
One of the advantages of the RDS service is that
you can locate a particular kind of program from
the preset channels (page 33) by specifying the
PTY codes.
• While the PTY code selected in Step 2 is still on
the display window:
3
Press PTY SEARCH again.
To search for a program using the PTY codes
NOTE
Before you start operation;
• The PTY Search is only applicable to preset
stations.
• To stop searching any time during the process,
press PTY SEARCH while searching.
• There is a time limit in doing the following steps. If
the setting is canceled before you finish, start from
step 1 again.
1
Press PTY SEARCH while
listening to an FM station.
S V C DV D - A
S V C DV D - A
While searching, “SEARCH” and the selected
PTY code alternate on the display window.
The system searches 30 preset FM stations,
stops when it finds the one you have selected,
and tunes in that station.
S V C DV D - A
“SELECT PTY” flashes on the display
window.
• While “SELECT PTY” is flashing:
2
To continue searching after the first stop
Press PTY SEARCH again while the indications
on the display window are flashing.
If no program is found, “NOT FOUND” appears on
the display window.
Press PTY SELECT + or PTY
SELECT – until the PTY code
you want appears on the display
window.
S V C DV D - A
• For details, see “Description of the PTY codes”
(page 36).
35
FS-Y1[B]_f.book Page 36 Friday, April 15, 2005 7:46 PM
Using the RDS (continued)
Description of the PTY codes
NEWS:
AFFAIRS:
INFO:
SPORT:
EDUCATE:
DRAMA:
CULTURE:
SCIENCE:
VARIED:
POP M:
ROCK M:
EASY M:
LIGHT M:
CLASSICS:
OTHER M:
WEATHER:
FINANCE:
CHILDREN:
SOCIAL:
RELIGION:
PHONE IN:
TRAVEL:
LEISURE:
JAZZ:
COUNTRY:
NATION M:
OLDIES:
36
News.
Topical program expanding or
enlarging upon the news —
debate, or analysis.
Programs the purpose of which
is to impart advice in the widest
sense.
Programs concerned with any
aspect of sports.
Educational programs.
All radio plays and serials.
Programs concerning any
aspect of national or regional
culture, including language,
theater, etc.
Programs about natural
sciences and technology.
Used for mainly speech-based
programs such as quizzes,
panel games and personality
interviews.
Commercial music of current
popular appeal.
Rock music.
Current contemporary music
considered to be “easylistening”.
Instrumental music, and vocal or
choral works.
Performances of major
orchestral works, symphonies,
chamber music, etc.
Music not fitting into any of the
other categories.
Weather reports and forecasts.
Stock Market reports,
commerce, trading etc.
Programs targeted at a young
audience.
Programs about sociology,
history, geography, psychology
and society.
Religious programs.
Involving members of the public
expressing their views either by
phone or at a public forum.
Travel information.
Programs about recreational
activities.
Jazz music.
Songs which originate from, or
continue the musical tradition of
the American Southern States.
Current popular music of the
nation or region in that country’s
language.
Music from the so-called “golden
age” of popular music.
FOLK M:
DOCUMENT:
TEST:
ALARM:
NONE:
Music which has its roots in the
musical culture of a particular
nation.
Programs concerning factual
matters, presented in an
investigative style.
Broadcasts for testing
emergency broadcast
equipment or unit.
Emergency announcement.
No program type, undefined
program, or difficult to
categorize into particular types.
NOTE
Classification of the PTY codes for some FM stations
may be different from the above list.
Switching to broadcast program of your
choice temporarily
Another convenient RDS service is called
“Enhanced Other Network”.
This allows the system to switch temporarily to a
broadcast program of your choice (TA, NEWS,
and/or INFO) from a different station except in the
following cases;
• When you are listening to non-RDS stations (all
AM – MW stations, some FM stations and other
sources).
• When the system is in standby mode.
NOTE
Before you start operations;
The Enhanced Other Network function is only
applicable to preset stations.
Press TA/News/Info repeatedly
until the program type indicator
(TA/NEWS/INFO) you want appears
on the display window.
Each time you press the button, the indicator on
the display window changes.
S V C DV D - A
TA NEWS INFO
3D PHONIC
TA/NEWS/
INFO indicators
TA
Traffic Announcement in your area.
NEWS
News.
INFO
Program the purpose of which is to
impart advice in the widest sense.
FS-Y1[B]_f.book Page 37 Friday, April 15, 2005 7:46 PM
Listening to radio
To stop listening to the program selected by
Enhanced Other Network
Press TA/News/Info repeatedly again so that the
program type indicator (TA/NEWS/INFO) goes off
from the display window. The system exits from
Enhanced Other Network standby mode and goes
back to the previously selected station.
Case 2
If the FM station you are listening to is
broadcasting the program you have selected
The system continues to receive the station but the
indicator of received PTY code starts flashing.
Case 1
When the program is over, the indicator of received
PTY code stops flashing and remains lit, but the
Enhanced Other Network function still remains
activated.
If there is no station broadcasting the program
you have selected
NOTE
How the Enhanced Other Network function
actually works
The system continues tuning in to the current
station.
When a station starts broadcasting the program
you have selected, the system automatically
switches to the station. The indicator of received
PTY code starts flashing.
When the program is over, the system goes back
to the previously tuned station, but the Enhanced
Other Network function still remains activated.
• In Enhanced Other Network standby mode, if you
change the source to play, Enhanced Other
Network standby mode is canceled temporarily.
• If you change the source to FM again, the system
returns to Enhanced Other Network standby mode.
• Enhanced Other Network data sent from some
stations may not be compatible with this system.
• Enhanced Other Network does not function for
some FM stations with RDS service.
• While listening to a program tuned in by the
Enhanced Other Network function, the station does
not change even if another network station starts
broadcasting a program of the same Enhanced
Other Network data.
• While listening to a program tuned in by the
Enhanced Other Network function, you can only use
TA/News/Info and RDS DISPLAY as the tuner
operation buttons.
37
FS-Y1[B]_f.book Page 38 Friday, April 15, 2005 7:46 PM
Listening to the sound of
other audio device
Setting the various timer
Connect the other audio device to this system in
advance (page 10).
1
Press AUX.
Setting the built-in clock
The source changes to AUX.
2
Play the other audio device.
For details, refer to the manual of the device
connected.
3
Adjust the volume and the
sound quality of the system
(page 16).
Without setting the built-in clock, you cannot use
any timers.
• To exit from the clock setting, press CLOCK/
TIMER as required.
• To correct a misentry during the procedure
below, pressing CANCEL can return to the
previous step.
1
Press CLOCK/TIMER.
S V C DV D - A
• If you have already adjusted the clock
before, press the button repeatedly until the
clock time starts flashing.
2
Press cursor 2/3 to adjust the
hour, then press SET.
3
Press cursor 2/3 to adjust the
minute, then press SET.
Now the built-in clock starts to work.
Setting the daily timer
Using the daily timer, you can wake up with your
favorite song.
• You can store the three daily timer settings;
however, you can activate only one of the daily
timer.
• To correct a misentry during the procedure
below, pressing CANCEL can return to the
previous step.
38
FS-Y1[B]_f.book Page 39 Friday, April 15, 2005 7:46 PM
Convenient functions
How the daily timer works:
Once the daily timer has been set, the timer
indicator and timer number indicator (1/2/3) are lit
on the display window. Daily timer turns on the
system at the same time everyday until the timer
setting is canceled manually or another daily timer
is activated.
When the on-time comes:
The system turns on, tunes in to the specified
station or start playback the loaded disc with the
volume level set to the preset level.
• The timer setting remains in memory until you
can change it.
• Without canceling the daily timer, you can
change the source or adjust the volume after the
daily timer starts playback.
1
Press CLOCK/TIMER repeatedly
to show “DAILY 1.”
• Each time you press the button, the clock
setting changes as follows:
Source
indication
DAILY 1
Clock adjust
ON 6:00
ON 18:00
DAILY 2
DAILY 3
ON 12:00
2
Press cursor 2/3 to adjust the
hour of the timer-on time, then
press SET.
3
Press cursor 2/3 to adjust the
minute of the timer-on time,
then press SET.
4
Repeat Step 2 and 3 to set the
timer-off time.
5
Press cursor 2/3 to select the
playback source, then SET.
• Each time you press the button, the clock
setting changes as follows:
AUX
6
Press cursor 2/3 to adjust the
volume level, then SET.
7
Turn off the system.
To turn off the timer setting
1
Press CLOCK/TIMER repeatedly
to select the timer setting.
2
Press CANCEL to turn off the
selected setting.
• Pressing SET activates the timer setting
again.
Auto Standby
If there is no operation for 3 minutes while the disc
is stopped, the power will be automatically turned
off.
Press A.STANDBY during playback
or while the disc is stopped, or no
disc is loaded (“NO DISC” appears).
The A.STANDBY indicator lights on the display
window on the main unit.
When a stopped state is entered (after playback is
finished, for example), the A.STANDBY indicator
starts blinking.
This means that the power will be turned off
automatically if there is no operation for 3 minutes.
And 10 seconds before the power is turned off,
“A.STANDBY” starts flashing.
Releasing Auto Standby
Press A.STANDBY.
“A.STANDBY” will be turned off on the display
window on the main unit.
NOTE
When the source is FM, AM, or AUX, Auto Standby
does not work.
TUNER FM
DISC
TUNER AM
• When selecting the tuner, press cursor 2/3
to select a preset channel.
• When selecting “DISC”, you can specify the
group and track. For the discs other than
MP3/WMA, the group selection does not
take effect.
39
FS-Y1[B]_f.book Page 40 Friday, April 15, 2005 7:46 PM
Setting the various timer (continued)
Sleep Timer
When the time you specify elapses, the system will
be turned off by itself.
Press SLEEP.
Each time you press the button, the time indicated
on the display window on the main unit changes (in
minutes).
Changing the time
Reselect the time by pressing SLEEP repeatedly.
Confirming the time
Press SLEEP once while Sleep Timer is set.
Releasing
Press SLEEP repeatedly until “SLEEP OFF”
appears.
NOTE
Sleep Timer will also be released when the power is
turned off.
40
Tray Lock
You can lock the disc tray to prevent the disc from
being ejected.
Setting
While the system is turned off, press 0 (Open/
Close) with 7 (Stop) on the main unit held.
“LOCKED” appears on the display window on the
main unit.
Releasing
Carry out the same operations as those for setting.
“UNLOCKED” appears on the display window on
the main unit.
FS-Y1[B]_f.book Page 41 Friday, April 15, 2005 7:46 PM
Troubleshooting
When you encounter a problem that seems to be a
fault, check the following points before contacting
your JVC service center.
Power source
7 Power does not come on.
• The power cord is not connected to the main
unit or an AC outlet.
→ Connect the power cord correctly
(page 11).
Operation
7 You cannot operate any button.
• Some specific operations may be inhibited
for some discs.
7 The remote control does not work.
• The dry-cell batteries have run out.
→ Replace the batteries (page 6).
7 A disc cannot be played back.
• In the case of DVD VIDEO discs
→ Check the Region Code number of the
discs (page 3).
• “NO PLAY” is displayed on the display
window.
It is not a disc that can be played on this
system.
→ Check the disc type (page 3).
Reference
7 The TV screen darkens.
• “SCREEN SAVER” is set.
→ If set, press any button (page 29).
7 The screen cannot be switched.
• The Progressive mode is applied only to
component video output.
About sound
7 There is no sound.
• Speakers are not connected correctly.
→ Page 9
• The sound is muted.
→ Page 16
• “NO AUDIO” is displayed on the display
window.
The disc may have been produced through
illegal copying.
→ Confirm at the store where you bought the
disc.
7 The sound is weak compared with TV or Video.
• “DVD LEVEL” is set to “NORMAL”.
→ Set to other than “NORMAL” (page 26).
7 The sound is distorted.
• The volume is turned up too high.
→ Turn down the volume (page 16).
7 No sound comes out of the subwoofer.
• “SUBWOOFER” is turned off.
→ Press S.WFR OUT to turn on (page 10).
• Parental Lock is set (page 30).
About images
7 No picture appears.
• The video cord is not connected correctly.
→ Page 11
About radio
7 The sound is noisy while receiving/Receiving
is disabled.
• The antenna is not connected correctly.
→ Connect the antenna correctly (page 8).
• Both of the component video jack and Svideo jack are connected.
→ Connect either (page 11).
7 The picture is distorted.
• A VCR is connected between the main unit
and the TV set.
→ Connect the main unit directly to the TV set
(page 11).
• Although this system is connected to a nonProgressive TV set, DVD’s scan mode is set
to “PROGRESSIVE”.
→ Set the scan mode to “INTERLACE”
(page 26).
7 The screen size is abnormal.
• The screen size is set improperly.
→ Set “MONITOR TYPE” according to the TV
set you are using (page 29).
41
FS-Y1[B]_f.book Page 42 Friday, April 15, 2005 7:46 PM
Troubleshooting (continued)
Others
7 It is not possible to switch audio or subtitles
between languages.
• The disc does not contain 2 or more
languages.
→ If only a single language is recorded on the
disc, switching to another language is
impossible (page 24).
7 No subtitle is displayed.
• The disc does not contain any subtitles.
→ A DVD VIDEO without subtitles cannot
display any subtitles.
• The subtitle language is set to “OFF”.
→ Specify a language (page 29).
• Before or after A point or B point in A-B
Repeat Playback, no subtitle may be
displayed.
7 The disc cannot be ejected.
• Tray Lock is set.
→ page 40
7 “LR ONLY” is displayed on the display window
(for a DVD AUDIO).
• Because, for the track being played back,
down mix is inhibited for multi-channel
sound, the sound of L and R is output directly
(a normal action).
If the system does not work properly
despite correction measures above
Many functions of this system are implemented by
microcomputers. If pressing any button does not
result in the normal action, disconnect the power
plug from the outlet, wait for a while, and reconnect
the system.
42
Language codes
Code
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
IW
JI
JW
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
Language
Afar
Abkhazian
Afrikaans
Ameharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean (KOR)
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Code
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NL
NO
OC
OM
OR
PA
PL
PS
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Reference
Language
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay (MAY)
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Wolof
Xhosa
Yoruba
Zulu
FS-Y1[B]_f.book Page 43 Friday, April 22, 2005 1:44 PM
Specifications
Reference
General
Power source:
Power consumption:
Audio input
AC 230 V
, 50 Hz
25 W (in operation)
1.0 W (on standby)
2.7 kg
Weight:
External dimensions
(W x H x D):
150 mm x 152 mm x 246 mm
DVD player
Playable discs: DVD VIDEO, DVD AUDIO, VCD,
SVCD, CD, CD-R/RW (CD, VCD,
MP3, WMA, JPEG format), DVD-R/RW (video format)
Sound input:
AUX x1
400 mV/50 kΩ
Tuner
FM tuner:
Receiving frequency:
Antenna:
AM (MW) tuner:
Receiving frequency:
Antenna:
87.50 MHz to 108.00 MHz
75 Ω- Unbalanced type
522 kHz to 1 629 kHz
External antenna jack (loop
antenna)
Speaker
Video output
Type:
Color system:
PAL
Horizontal resolution: 500 lines
Composite x1:
1.0 V (p-p)/75 Ω,
synchronization negative
S-video x1:
Y output: 1.0 V (p-p)/75 Ω,
synchronization negative
C output: 0.3 V (p-p)/75 Ω
Component x1:
Y output: 1.0 V (p-p)/75 Ω
PB/PR output: 0.7 V (p-p)/75 Ω
Full range
1-way bass-reflex type
Magnetically shielded type
Speaker:
8 cm cone x1
Frequency response:
60 to 20 000 Hz
Power handling capacity: 20 W
Impedance:
4Ω
Sound pressure level:
81 dB/W • m
Dimension (W x H x D):
120 mm x 150 mm x 188 mm
Weight:
1.5 kg each
Audio output
Analog sound output:
Speakers x2
Output power:
(IEC 268-3)
Fitting impedance:
Headphones x1:
Fitting impedance:
Subwoofer x1:
Digital sound output:
Optical x1:
36 W (18 W+18 W)
at 4 Ω (10% THD)
4 Ω to 16 Ω
11 mW/32 Ω
16 Ω to 1 kΩ
500 mVrms/10 kΩ
–21 dBm to –15 dBm
Designs and Specifications are subject to change
without notice.
43
FS-Y1[B]_f.book Page 44 Friday, April 15, 2005 7:46 PM
FS-Y1
COMPACT
T COMPONENT SYSTEM
EN
c
2005 Victor Company of Japan, Limited
0405AIMMDWJEM