Technical data | Cadillac 2010 Escalade ESV Automobile User Manual

INSTRUCTIONS–PARTS LIST
308–457
Rev. B
Supersedes A
This manual contains important
warnings and information.
READ AND RETAIN FOR REFERENCE
23:1 MONARK CARBON STEEL, CART MOUNTED
AA200hs Air-Assisted Airless
Spray Package
See the Data Sheet, 305–663, for application information.
2760 psi (190 bar) Maximum System Working Pressure
120 psi (8.3 bar) Maximum Air Inlet Pressure
Model 237–418, Series A
This complete package includes a pump,
an AA200hs air-assisted airless–spray gun
with a 411 spray tip,a portable cart, 25 ft. (7.6 m) air
and fluid hoses,
air and fluid controls, and a fluid feed.
IMPORTANT
This manual provides the basic safety, installation and
operation information for the package. For your safety,
also read the component manuals supplied with this
package before operating it.
GRACO INC.
P.O. BOX 1441 MINNEAPOLIS, MN
COPYRIGHT 1994, GRACO INC.
55440–1441
Table of Contents
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Ground the system . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
System Component Information . . . . . . . . . . . . . . . . . . 7
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pressure relief procedure . . . . . . . . . . . . . . . . . . . . . . 8
Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Graco Phone Numbers . . . . . . . . . . . . . . . . . . . . . . . . . 16
Symbols
Warning Symbol
WARNING
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
Caution Symbol
CAUTION
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
corresponding instructions.
WARNING
INJECTION HAZARD
Spray from the gun, hose leaks or ruptured components can inject fluid into your body and cause
extremely serious injury, including the need for amputation. Splashing fluid in the eyes or on the skin
can also cause can also cause serious injury.
D Fluid injected into the skin is a serious injury. The injury might look like just a cut, but it is a serious injury. Get immediate medical attention.
D Do not point the spray gun at anyone or any part of the body.
D Do not put hand or fingers over the spray tip.
D Do not stop or deflect fluid leaks with your hand, body, glove or rag.
D Do not “blow back” fluid; this is not an air spray system.
D Always have the tip guard and the trigger guard on the spray gun when spraying.
D Check the gun diffuser operation weekly. Refer to the gun manual.
D Be sure the gun trigger safety operates before spraying the gun.
D Lock the gun trigger safety when you stop spraying.
D Follow the Pressure relief procedure on page 8 if the spray tip clogs and before cleaning,
checking or servicing the equipment.
D Tighten all fluid connections before each use.
D Check the hoses, tubes and couplings daily. Replace worn or damaged parts immediately. Permanently coupled hoses cannot be repaired.
D Handle and route hoses and tubes carefully. Keep hoses and tubes away from moving parts and
hot surfaces. Do not use the hoses to pull equipment. Do not expose Graco hoses to temperatures above 180_F (82_C) or below –40_F (–40_C).
TOXIC FLUID HAZARD
Improper handling of hazardous fluids or inhaling toxic fumes can cause extremely serious injury,
even death, due to splashing in the eyes, ingestion, or bodily contamination.
D Know the specific hazards of the fluid you are using.
D Store hazardous fluid in an approved container. Dispose hazardous fluid according to all local,
state and national guidelines.
D Wear appropriate clothing, gloves, eyewear and respirator.
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor air ventilation, open flames or sparks can cause a hazardous condition
and result in a fire or explosion and serious injury.
D Ground the equipment and the object being sprayed. See Ground the system on 6.
D If there is any static sparking while using the equipment, stop spraying immediately. Identify
and correct the problem.
D Provide fresh air ventilation to avoid the buildup of flammable vapors from solvent or the fluid being sprayed.
D Do not smoke in the spray area.
D Extinguish all open flames or pilot lights in the spray area.
D Do not turn on or off any light switch in the spray area.
D Electrically disconnect all equipment in the spray area.
D Keep the spray area free of debris, including solvent, rags and gasoline.
D Do not operate a gasoline engine in the spray area.
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture, malfunction or start unexpectedly and result
in serious injury.
D This equipment is for professional use only.
D Read all instruction manuals, tags, and labels before operating the equipment.
D Use the equipment only for its intended purpose. If you are in doubt about this, call Graco Technical Assistance at 1–800–543–0339.
D Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D Do not exceed the 2760 psi (190 bar) maximum working pressure at 120 psi (8.3 bar) maximum incoming air pressure of the pump, or the maximum working pressure of any accessory
used with it.
D Do not move or lift pressurized equipment.
D Use fluids or solvents which are compatible with equipment wetted parts. Refer to the Technical Data
section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
D Fluid hoses must have spring guards on both ends to protect it from rupture caused by kinks or
bends at or close to the couplings.
D Comply with all applicable local, state and national fire, electrical and other safety regulations.
D Do not touch the heater during operation; it is very hot.
MOVING PARTS HAZARD
Moving parts, such as the air motor piston located behind the air motor plates, which can pinch or
amputate fingers.
D Never operate the equipment with the air motor plates removed.
D Keep clear of any moving parts when starting or operating the equipment.
Setup
I.
Prepare the operator.
All persons who operate the system should be trained
in the safe, efficient operation of all system components as well as the proper handling of the chemical
coating. At a minimum, all operators should
thoroughly read the safety, installation and operation
sections of this manual and the component manuals.
II.
Prepare the site.
1. Use a minimum recommended 5 HP (3.7 kW) air
compressor for efficient operation.
2. Clear obstacles and debris that could hinder the
operator’s movement.
4. Have a grounded, metal waste–pail available to
use when draining the fluid filter.
5. Ventilate the spray booth.
WARNING
To prevent hazardous concentrations of toxic and/
or flammable vapors, spray only in a properly ventilated spray booth. Never operate the spray gun
unless ventilation fans are operating.
Check and follow all of the national, state and local
codes regarding air exhaust velocity requirements.
3. Bring an air line from your compressed air supply
to the pump location. Be sure the air is dry and
filtered. Install a bleed–type master air valve (A)
upstream from the pump. Another master air valve
(14) is supplied with the package. When the
bleed–type master air valve is closed and the
pump air regulator (8a) is opened, the valve
relieves all air pressure to the system.
KEY
B
A
Components you must supply:
Components supplied with package:
A
1
3
4
6
7
8a
8b
14
30
B
C
D
E
Bleed-type master air valve
Required for pump; order
part no. 107–142, 1/4” npt(f)
Air filter. Order part no.
106–149, 1/2 npt(f)
Air supply line
Grounded 5 gallon metal pail
Air line moisture trap
C
23:1 Monark pump
Air-assisted airless spray gun
Spray tip
Gun fluid hose
Gun air hose
Pump air regulator
Gun air regulator
Bleed–type air valve
Pump ground wire
E
1
C
3,4
30
8b
6
8a
7
14
D
Fig. 1
04072
Setup
III.
Unpack the system.
1. In addition to the assembled components, the air
and fluid hoses, gun and instruction manuals are
packaged separately in the main shipping container. These are the manuals you should receive:
307–619
308–176
307–273
308–167
308–861
IV.
23:1 ratio Monark pump
Air-assisted airless spray gun
Fluid filter
Air regulator
Ball valve
Connect the hoses and gun to the
system. See Fig. 1.
1. Connect the blue fluid hose (6) between the fluid
filter and the fluid inlet of the spray gun (3). These
are 1/4–18 npsm(f) swivel fittings.
2. Connect the red air hose (7) between the gun air
regulator (8b) and the air inlet of the spray gun (3).
These are 1/4–18 npsm(f) swivel fittings.
3. Verify that all fittings throughout the system are
tightened securely.
6
308-457
V.
Ground the system.
WARNING
To reduce the risk of static sparking, ground the
pump and all other equipment used or located in
the spray area. Check your local electrical code for
detailed grounding instructions for your area and
type of equipment. Ground all of this equipment.
Also read FIRE OR EXPLOSION HAZARD on
page 4.
1. Pump: one end of the ground wire (30) is already
connected to the air motor grounding lug. Connect
the clamp end of the ground wire to a true earth
ground.
2. Air and fluid hoses: use only electrically conductive
hoses with a maximum of 500 feet (150 m) combined hose length to ensure grounding continuity.
3. Air compressor: according to manufacturer’s
recommendations.
4. Fluid supply container: according to local code.
5. All solvent pails used when flushing, according to
local code. Use only metal pails, which are conductive. Do not place the pail on a non-conductive
surface, such as paper or cardboard, which interrupts the grounding continuity.
System Component Information
I.
How to use the air–assisted airless
spray gun.
With an air-assisted airless spray gun, the spray tip
shapes the fluid into a fan pattern. Air from the air cap
further atomizes the fluid and completes the atomization of the paint tails into the pattern to produce a more
uniform pattern.
II.
How to change the spray pattern
direction.
1. Relieve the air and fluid pressure.
2. Install a spray tip in the gun. Rotate the air cap
(the spray tip rotates with it) to determine the
direction of the spray pattern. See Fig. 3.
Vertical Spray Pattern
Horizontal Spray Pattern
The spray gun has a built-in lead and lag operation.
When triggered, the gun emits air before the fluid is
discharged. When the trigger is released, the fluid
stops before the air flow stops. This helps assure the
spray is atomized and prevents fluid buildup on the air
cap.
0791
Fig. 3
NOTE: The gun air and fluid inlets have 1/4–18 npsm
(R1/4–19) compound male threads that are compatible
with NPSM and BSP female swivel
connectors.
1. The fan pattern valve (E) can be used to reduce
the pattern by about 25% of the total pattern width.
As the valve is opened, the pattern will reduce
slightly. The tip used designates the total width of
the spray pattern.
2. To unlock the gun trigger safety, turn the safety so
it is parallel with the trigger. To lock the gun trigger
safety, turn the safety to a right angle with the trigger. See Fig. 2.
1
UNLOCKED gun trigger safety
2
LOCKED gun trigger safety
III.
How to adjust the air regulators.
See Fig. 4.
As you look at the system, the air regulator (8a) on the
left regulates air to the gun and the air regulator (8b)
on the right regulates air to the pump.
1. Always open air regulators slowly to prevent surging during startup.
2. To open the regulator, which allows air to flow, turn
the T–handle IN (clockwise). Turn the T–handle
OUT (counterclockwise) to close off the air flow.
Be sure the jam nut under the T–handle does not
interfere with your adjustments. Tighten the jam
nut to lock in the setting, if desired.
8b
E
2
8a
1
CCW
CW
0795A
Fig. 2
04069
Fig. 4
Operation
I.
Pressure relief procedure
II.
WARNING
The system remains pressurized until pressure is
manually relieved. To reduce the risk of serious
injury, including skin injection from pressurized fluid
or accidental spray from the gun, or injury due to
splashing fluid in the eyes or on the skin, follow this
procedure whenever you:
D
D
D
D
are told to relieve pressure;
stop spraying;
check or service any system equipment;
install, clean or change spray tips.
Flush the pump before the first use.
Flush with a solvent compatible to your fluid. Consult
the fluid manufacturer’s literature for recommendations. See Flushing on page 10.
III.
Prime the system.
See Fig. 5.
1. Remove the air cap and spray tip from the gun.
2. Close the filter drain valve (26).
3. Put the suction tube into the fluid supply container.
4. Make sure the air regulators (8a,8b) are closed.
1. Lock the gun trigger safety.
2. Close the bleed-type master air valves (A,14).
3. Close the air regulators (8a,8b).
5. Open the master air valves (A,14).
NOTE: In the next steps, the pump will cycle quickly
until air is purged.
4. Unlock the gun trigger safety.
5. Hold the gun firmly against a grounded metal
waste pail. Trigger the gun to relieve pressure.
6. Lock the gun trigger safety.
7. Open the filter drain valve (26), having a container
ready to catch the drainage. Close the drain valve.
If you suspect that the spray tip or hose is completely
clogged or that pressure has not been fully relieved,
very slow loosen the tip retaining nut or hose end coupling and relieve pressure gradually. Clean the tip or
hose obstruction.
6. Slowly turn on the pump air regulator (8a) until the
pump cycles slowly.
7. Hold a metal part of the gun firmly against and
aimed into the grounded metal waste pail. Trigger
the gun while increasing pressure at the pump air
regulator (8a) just enough to purge the air and
storage solvent from the system. When new fluid
comes from the gun, release the trigger. Lock the
gun trigger safety.
A
KEY
A
3
8a
8b
14
26
Bleed-type master air valve
Air-assisted airless spray gun
Pump air regulator
Gun air regulator
Bleed–type air valve
Filter drain valve
3
C
8a
8b
14
26
04072
Fig. 5
Operation
IV.
Set the fluid and air pressure.
V.
1. Install the spray tip and air cap on the gun.
2. Adjust the pump air pressure regulator until the
pressure shown on the fluid filter gauge is about
800 psi (56 bar). This should require approximately
35 psi (2.4 bar) air pressure to the pump.
3. Test spray a pass or stationary horizontal pattern.
Hold the gun 10 to 12 in. (250 to 300 mm) from the
paper. Stripes in the outer edges of the pass or
spots at the ends of the stationary pattern are
likely at this point.
NOTE: If there are no stripes or spots, lower the
fluid pressure until they appear before turning on
the air to the gun.
4. Partially trigger the gun so only air is emitted. Set
the gun air regulator to 20 psi (1.4 bar).
You are now ready for production
spraying.
CAUTION
When using catalyzed fluids, observe the pot life
as recommended by the fluid manufacturer. Always
flush the system before the pot life has expired to
prevent dried fluid which may be difficult to clean
out and may damage the system.
VI.
When to shut down the system.
Shut down the system at the end of the work shift and
before checking, adjusting, cleaning or repairing the
system. Always follow the Pressure relief procedure
on page 8.
5. Retest the spray pattern. Trigger the gun and
adjust the gun’s air control valve (C) to add air to
the aircap and to eliminate stripes or spots. If there
are no stripes or spots, you are ready to start
spraying.
6. If there are stripes or spots in the spray pattern,
raise the pump air pressure until you raise the fluid
outlet pressure by about 100 psi (6.9 bar) and try
again. Continue to raise the fluid pressure in
100 psi (6.9 bar) increments until the pattern is full
and clean. Do not exceed 120 psi (8.3 bar)
incoming air pressure or 2760 psi (190 bar) fluid
working pressure.
NOTE: Always use the lowest fluid and air pressure required for good atomization and spray pattern for maximum fluid efficiency. Air pressure over
approximately 30 psi (2.1 bar) will cause turbulence in the fan pattern, dirty air caps and slower
production capability.
WARNING
This system has a maximum air working pressure
of 120 psi (8.3 bar) which produces a maximum
fluid working pressure of 2760 psi (190 bar). Higher
pressure can cause the system to rupture or malfunction and result in serious injury.
308-457
9
Flushing
I.
7. Slowly turn on the pump air regulator (8a) until the
pump cycles slowly.
When to flush.
D Before the first time use
D When changing colors
D Before fluid can dry or settle out in a dormant system (observe the recommended fluid pot life on catalyzed fluids)
D Before storing the system
II.
8. Hold a metal part of the gun firmly against the
grounded metal waste pail. Trigger the gun. Slowly
increase the pump air regulator setting until the
fluid flows freely. (Some air will spit from the gun
until the fluid arrives.)
9. Keeping the gun triggered, decrease the pump air
regulator (8a) pressure as much as possible
without stalling the pump, and pump out the
solvent until air comes through the gun.
How to flush.
See Fig. 6.
1. Relieve pressure. See page 8.
10. Repeat the procedure with clean solvent, if needed.
2. Remove the air cap and spray tip before flushing.
11. Release the trigger and lock the gun trigger safety.
3. Unscrew the fluid filter (5) bowl. Remove the
screen. See manual 307–273. Reinstall the bowl
without the screen.
12. Close the master air valves (A,14). Fully close the
pump air regulator (8a).
4. Put the suction tube into a grounded metal pail with
about 1/2 gallon (2 liters) of a compatible solvent.
5. Make sure the air regulators (8a,8b) are closed.
NOTE: The gun air regulator (8b) always stays closed
during flushing.
13. Open the drain valve (26), having a container
ready to catch the drainage.
14. Remove the suction hose from the solvent and
place it in an empty container.
15. Clean the filter screen, air cap and spray tip separately. Reinstall the filter screen.
16. Thoroughly clean the inside and outside of the
suction tube.
6. Open the master air valves (A,14).
A
KEY
A
3
5
8a
8b
14
26
Bleed-type master air valve
Air-assisted airless spray gun
Fluid filter
Pump air regulator
Gun air regulator
Bleed–type air valve
Filter drain valve
3
C
8a
8b
14
5
26
04072
Fig. 6
10
308-457
Notes
308-457
11
Parts
Model 237–418, Series A
Includes items 1 to 37
Ref
No.
Part No.
Description
1
223–596
23:1 RATIO MONARK PUMP
2
224–044
See 307–619 for parts
CART, portable
See 308–136 for parts
3
223–283
4
182–411
See 308–176 for parts
SPRAY TIP, 0.011 orifice,
8–10” (203–254 mm) fan width
5
218–029
FLUID FILTER
6
214–698
7
8
210–867
104–267
Qty
See 307–273 for parts
FLUID HOSE, 3/16” x 25’ (15.2 m),
nylon, spring guards both ends,
1/4–18 npsm(fbe)
AIR HOSE, cpld 1/4 npsm (fbe)
1/4” ID x 25’ (6.3 mm ID x 7.6 m)
101–180
10
1
1
1
1
2
161–037
90_ SWIVEL ADAPTER UNION
11
204–560
1/2 npt(m) x 3/8 npsm(f) swivel
1
AIR HOSE, buna-N, 3/8” (10 mm) ID,
cpld 3/8 npt(mbe), 18” (457 mm) long 1
12
222–297
45_ SWIVEL ADAPTER UNION,
13
14
158–491
107–142
15
16
102–814
166–999
1/2 npt(m) x 1/2 npsm(f) swivel
1
NIPPLE, 1/2 npt, 1.625” (41 mm) long 1
BLEED–TYPE AIR VALVE,
17
18
162–453
214–960
19
165–767
12
308-457
FLUID PRESSURE GAUGE
ELBOW, reducing street,
1/2 npt(m) x 1/4 npt(f)
NIPPLE, 1/4 npt x 1/4 npsm
SUCTION HOSE, 3/4 npt (mbe),
3/4 ” ID x 3.5’ (19 mm ID x 1.06 m)
SUCTION TUBE, 3/4 npt(f)
20
21
23
100–349
100–016
155–665
24
25
26
206–994
156–849
210–658
27
28
29
156–877
188–595
102–254
30
237–569
31
32
33
34
150–286
165–472
100–509
179–749
35
36
37
100–015
100–840
160–790
FLUID INTAKE ELBOW, 3/4 npt(f) 1
LOCKWASHER, 1/4” spring
2
SWIVEL UNION,
3/8 npt(m) x 3/8 npsm(f)
1
THROAT SEAL LIQUID, 8 oz.
1
NIPPLE, 3/8 npt x 3/8–18.6 sf
1
BALL VALVE, 3/8 npt (mbe),
see 306–861 for parts
1
NIPPLE, 1/2 npt, 2.5” (63.5 mm)
2
PUMP MOUNTING PLATE
1
SCREW, hex hd, 1/4–20 x
7/8” (22 mm) long
2
GROUND WIRE and CLAMP
12 gauge (1.5 mm2), 25’ (7.6 m)
1
ADAPTER
1
ELBOW, 90_; 3/8 npt (fbe)
1
PLUG, 1/4 npt sq hd pipe
3
AIR MANIFOLD, 1/2 npt inlet,
two 1/2 npt outlets
1
NUT, hex; 1/4–20
2
ELBOW; 1/4 npt (m x f)
1
NIPPLE
1
2
AIR PRESSURE GAUGE
1/2 npt (f)
Description
1
AIR REGULATOR
0–200 psi (0–14 bar)
Part No.
1
AIR ASSISTED AIRLESS
SPRAY GUN
0–125 psi (0–9 bar) range
See 308–167 for parts
9
1
Ref
No.
1
1
1
2
1
1
Qty
Manual Change
Summary
This manual was updated to correct the parts drawing
on page 13. The following parts lists changes were
also made.
Assembly
Changed
Part
Status
Ref
No.
Part No.
Name
237–418
Package
Add
31
150–286
Adapter
Old
New
37
37
150–286
160–790
Nipple
Nipple
Parts
16
9
17
30
29
8
1
22
33
27
37
9
8
34
32
27
10
13
11
12
2
A
33
14
28
15
23
25
21
35
5
36
17
33
A
31
26
20
18
19
3,4
6
7
308-457
13
Notes
14
308-457
Notes
308-457
15
Technical Data
Maximum Fluid Working Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 2760 psi (190 bar)
Maximum Air Operating Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 120 psi (8.3 bar)
Pump Air Consumption . . . free flow: 20 scfm at 100 psi (0.56 m3/min at 6.9 bar)
Gun Air Consumption . . . . . . . . . . . . . . . 5 scfm at 30 psi (0.14 m3/min at 2.1 bar)
Wetted Parts
Pump . . . . . . . . . . . . carbon steel, 304/316/420/17–4 pH stainless steel,
chrome, chrome and zinc plating,
tungsten carbide, PTFE, leather Gun . . . . . . . . . . . . . . . . . . . 303 stainless steel, carbide, UHMWPE CV75,
polyethylene, PTFE, Delrin Fluid filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . carbon steel, PTFE,
304/316 stainless steel, polyethylene
Fluid fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . carbon steel
Fluid hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . nylon
NOTE: all 304, 316 and 17–4 pH SST are electropolished and/or passivated.
Delrinis a registered trademark of the Du Pont Company
.
The Graco Warranty and Disclaimers
WARRANTY
Graco warrants all equipment manufactured by it and bearing its name to be free from defects in fluid and workmanship on the date of
sale by an authorized Graco distributor to the original purchaser for use. As purchaser’s sole remedy for breach of this warranty, Graco
will, for a period of twelve months from the date of sale, repair or replace any part of the equipment proven defective. This warranty
applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Graco
component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of
structures, accessories, equipment or fluids not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or fluids not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claim. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment
will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in fluid or
workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor and transportation.
DISCLAIMERS AND LIMITATIONS
The terms of this warranty constitute purchaser’s sole and exclusive remedy and are in lieu of any other warranties (express or
implied), including warranty of merchantability or warranty of fitness for a particular purpose, and of any non–contractual liabilities, including product liabilities, based on negligence or strict liability. Every form of liability for direct, special or consequential
damages or loss is expressly excluded and denied. In no case shall Graco’s liability exceed the amount of the purchase price. Any
action for breach of warranty must be brought within two (2) years of the date of sale.
EQUIPMENT NOT COVERED BY GRACO WARRANTY
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose, with
respect to accessories, equipment, fluids, or components sold but not manufactured by Graco. These items sold, but not manufactured by Graco (such as electric motor, switches, hose, etc.) are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
Graco Phone Numbers
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor
closest to you: 1–800–367–4023 Toll Free
FOR TECHNICAL ASSISTANCE, service repair
information or assistance regarding the application of
Graco equipment: 1–800–543–0339 Toll Free
Sales Offices: Atlanta, Chicago, Dallas, Detroit, Los Angeles, Mt. Arlington (N.J.)
Foreign Offices: Canada, England, Korea, Switzerland, France, Germany, Hong Kong, Japan
GRACO INC.
P.O. BOX 1441 MINNEAPOLIS, MN
55440–1441
PRINTED IN U.S.A. 308–457 September, 1994, Revised November, 1994
Download PDF

advertising