Cadillac CTS Automobile Accessories User Manual

COMPACT COMPONENT SYSTEM
MX-KC58
—Consists of CA-MXKC58 and SP-MXKC58
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT1688-001B
[J]
Warnings, Cautions and Others
Mises en garde, précautions et indications diverses
(For U.S.A.)
(For U.S.A.)
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
(For U.S.A.)
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
Changes or modifications not approved by JVC
could void the user’s authority to operate the
equipment.
G-1
(For U.S.A.)
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to section 820-40 of the NEC
which provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical.
For Canada/pour le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED
THE CLASS B LIMITS FOR RADIO NOISE
EMISSIONS FROM DIGITAL APPARATUS AS
SET OUT IN THE INTERFERENCE-CAUSING
EQUIPMENT STANDARD ENTITLED “DIGITAL
APPARATUS,” ICES-003 OF THE DEPARTMENT
OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES
LIMITES DE BRUITS RADIOELECTRIQUES
APPLICABLES AUX APPAREILS NUMIRIQUES
DE CLASSE B PRESCRITES DANS LA NORME
SUR LE MATERIEL BROUILLEUR; “APPAREILS
NUMERIQUES”, NMB-003 EDICTEE PAR LE
MINISTRE DES COMMUNICATIONS.
CAUTION –– % STANDBY/ON button !
Disconnect the mains plug to shut the power off
completely (all lamps and indications go off). When
installing the product, ensure that the plug is easily
accessible. The % STANDBY/ON button in any
position does not disconnect the mains line.
• When the unit is on standby, the STANDBY lamp
lights red.
• When the unit is turned on, the STANDBY lamp
goes off.
The power can be remote controlled.
ATTENTION –– Touche % STANDBY/ON
Déconnectez la fiche de secteur pour mettre
l’appareil complètement hors tension (tous les
témoins et toutes les indications s’éteignent). Lors
de l’installation de l’appareil, assurez-vous que la
fiche soit facilement accessible. La touche %
STANDBY/ON dans n’importe quelle position ne
déconnec-te pas l’appareil du secteur.
• Quand l’appareil est en mode d’attente, le témoin
STANDBY est al-lumé en rouge.
• Quand l’appareil est sous tension, le témoin
STANDBY s’éteint.
L’alimentation peut être télécommandée.
G-2
IMPORTANT FOR LASER PRODUCTS / IMPORTANT POUR PRODUITS LASER
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or the cabinet. There are no user serviceable
parts inside the unit; leave all servicing to qualified service personnel.
3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do
not stare into beam. (For Canada) Visible and/or invisible class 1M laser radiation when
open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.
1. PRODUIT LASER CLASSE 1
2. ATTENTION: N'ouvrez pas le couvercle supérieur ni le boîtier. Il n'y a aucune pièce
réparable par l'utilisateur à l'intérieur de l'appareil; confiez toute réparation à un
personnel qualifié.
3. ATTENTION: (Pour les Etats-Unis) Radiation laser de classe II visibles et/ou invisible si
l’appareil est ouvert. Ne regardez pas le rayon. (Pour le Canada) Rayonnement laser
visible et/ ou invisible de classe 1M une fois ouvert. Ne pas regarder directement avec
des instruments optiques.
4. REPRODUCTION DE L'ÉTIQUETTE: ÉTIQUETTE DE PRÉCAUTION PLACÉE À
L'INTERIEUR DE L'APPAREIL.
G-3
CAUTION
ATTENTION
1. Do not block the ventilation openings or holes.
(If the ventilation openings or holes are
blocked by a newspaper or cloth, etc., the heat
may not be able to get out.)
2. Do not place any naked flame sources, such
as lighted candles, on the apparatus.
3. When discarding batteries, environmental
problems must be considered and local rules
or laws governing the disposal of these batteries must be followed strictly.
4. Do not expose this apparatus to rain, moisture,
dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on
the apparatus.
1. Ne bloquez pas les orifices ou les trous de
ventilation. (Si les orifices ou les trous de ventilation sont bloqués par un journal un tissu,
etc., la chaleur pent ne pas être évacuée correctement de l’appareil.)
2. Ne placez aucune source de flamme nue, telle
qu’une bougie, sur l’appareil.
3. Lors de la mise au rebut des piles, veuillez prendre en
considération les problèmes de l’environnement et
suivre strictement les règles et, les lois locales sur la
mise au rebut des piles.
4. N’exposez pas cet appareil à la pluie, à l’humidité,
à un égouttement ou à des éclaboussures et ne
placez pas des objets remplis de liquide, tels
qu’un vase, sur l’appareil.
CAUTION:
Excessive sound pressure from earphones or
headphones can cause hearing loss.
ATTENTION:
Une pression acoustique excessive des écouteurs
ou du casque d’écoute peut entraîner une perte
auditive.
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm
(3-15/16") or more.
Attention: Aération correcte
Pour prévenir tout risque de décharge électrique ou d’incendie et éviter toute détérioration, installez l’appareil de la manière
suivante:
1. Avant: Bien dégagé de tout objet.
2. Côtés/dessus/dessous: Assurez-vous que rien ne bloque les espaces indiqués sur le schéma ci-dessous.
3. Dessous: Posez l’appareil sur une surface plane et horizontale. Veillez à ce que sa ventilation correcte puisse se faire en le
plaçant sur un support d’au moins dix centimètres de hauteur.
Front
Face
15cm
(5 15 /16 in)
15cm
(5 15 /16 in)
1cm
( 7 /16 in)
1cm
( 7 /16 in)
15cm
(5 15 /16 in)
Side
Côté
15cm
(5 15 /16 in)
15cm
(5 15 /16 in)
10cm
(3 15 /16 in)
SP-MXKC58
CA-MXKC58
SP-MXKC58
CA-MXKC58
* About the cooling fan
Cooling fan is built into the main unit. The internal cooling fan automatically rotates for emitting generated heat. To ensure
sufficient cooling, leave a space of more than 1 cm between the main unit and the speakers or other objects.
* À propos du ventilateur de refroidissement
Un ventilateur de refroidissement est incorporé dans l’unité principale. Ce ventilateur de refroidissement interne tourne
automatiquement pour libérer la chaleur générée. Afin de garantir un refroidissement suffisant, laissez un espace de plus
d’1 cm entre l’unité principale et les enceintes ou d’autres objets.
G-4
Table of Contents
Table of Contents ............................................ 1
Introduction ..................................................... 2
Precautions ......................................................................2
How to Read This Manual ..............................................3
Getting Started ................................................ 4
Step 1: Unpack ................................................................4
Step 2: Prepare the Remote Control ...............................4
Step 3: Hook Up .............................................................4
DEMO Mode ..................................................................6
Before Operating the System ......................... 7
Parts Index ......................................................................7
Daily Operations—Playback .......................... 9
Listening to the Radio ...................................................10
Playing Back a Disc ......................................................11
Playing back from iPod ................................................13
Playing Back from other equipment .............................15
Daily Operations – Sound & Other Adjustment
...................................................................... 16
Adjusting the Volume ...................................................16
Adjusting the Sound .....................................................16
Setting the Clock ..........................................................16
Advanced Radio Operations ........................ 17
About XM Satellite Radio ............................................17
Preparation ....................................................................17
Listening to the XM Satellite Radio .............................18
Using preset tuning .......................................................19
Changing the channel information ................................20
Messages on the display ...............................................20
Advanced Disc Operations ........................... 21
Programming the Playing Order—Program Play .........21
Playing at Random—Random Play ..............................22
Playing Repeatedly—Repeat Play ................................23
Prohibiting Disc Ejection—Child Lock .......................23
Using the Timers ........................................... 24
Setting the Timer ..........................................................24
Additional Information ................................ 26
Learning More about This System ...............................26
Troubleshooting ............................................................27
Maintenance ..................................................................27
Specifications ................................................................28
1
Introduction
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to
ensure your complete understanding and to obtain the best
possible performance from the unit.
Internal heat
• A cooling fan is mounted on the rear panel to prevent heat
buildup inside the main unit (see page G-4).
For safety, observe the following carefully:
• Make sure there is good ventilation around
the main unit. Poor ventilation could
overheat and damage the System.
• DO NOT block the cooling fan and the
ventilation openings or holes. If they are
blocked by a newspaper or cloth, etc., the
heat may not be able to get out.
Precautions
Installation
• Install in a place which is level, dry and neither too hot nor
too cold—between 5°C and 35°C (41°F and 95°F).
• Install the System in a location with adequate ventilation to
prevent internal heat buildup inside the System.
DO NOT install the System in a location near
heat sources, or in a place subject to direct
sunlight, excessive dust or vibration.
• Leave sufficient distance between the System and the TV.
• Keep the speakers away from the TV to avoid interference
with TV.
Power sources
• When unplugging the System from the wall outlet, always
pull on the plug, not the AC power cord.
DO NOT handle the AC power cord with wet
hands.
Others
• Should any metallic object or liquid fall into the System,
unplug the AC power cord and consult your dealer before
operating any further.
DO NOT disassemble the System since there
are no user serviceable parts inside.
• If you are not going to operate the System for an extended
period of time, unplug the AC power cord from the wall outlet.
If anything goes wrong, unplug the AC power cord and
consult your dealer.
Moisture condensation
Moisture may condense on the lenses inside the System in
the following cases:
• After starting to heat the room
• In a damp room
• If the System is brought directly from a cold to a warm
place
Should this occur, the System may malfunction. In this case,
leave the System turned on for a few hours until the moisture
evaporates, unplug the AC power cord, then plug it in again.
2
How to Read This Manual
To make this manual as simple and easy-to-understand as
possible, we have adapted the following methods:
• Button and control operations are explained as listed in the
table below. In this manual, the operations using the
remote control is mainly explained; however, you can use
the buttons and controls on the main unit if they have the
same (or similar) name and marks.
• Some related tips and notes are explained later in the
sections “Learning More about This System” and
“Troubleshooting,” but not in the same section
explaining the operations. If you want to know more about
the functions, or if you have a doubt about the functions, go
to these sections and you will find the answers.
Indicates that you press the button
briefly.
Indicates that you press the button
briefly and repeatedly until an option
you want is selected.
Indicates that you press one of the
buttons.
2 sec.
Indicates that you press and hold the
button for specified seconds.
• The number inside the arrow
indicates the period of press (in this
example, 2 seconds).
• If no number is inside the arrow,
press and hold until the entire
procedure is complete or until you
get a result you want.
Indicates that you turn the control
toward the specified direction(s).
Remote
ONLY
Main Unit
ONLY
3
Indicates that this operation is only possible
using the remote control.
Indicates that this operation is only possible
using the buttons and controls on the main
unit.
Getting Started
Step 1: Unpack
After unpacking, check to be sure that you have all the following items. The number in parentheses indicates the quantity of
each piece supplied.
• AM Loop Antenna (1)
• FM Wire Antenna (1)
• Remote Control (1)
• Batteries (2)
• Connection Cable for iPod (1)
• Stand for iPod (1)
If any of these items are missing, contact your dealer immediately.
Step 2: Prepare the Remote Control
Insert the batteries into the remote control by matching the polarity (+ and –) correctly.
R6P(SUM-3)/AA(15F)
If the range or effectiveness of the remote control decreases, replace both batteries.
Caution
Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
Step 3: Hook Up
Make all connections before plugging the System into an AC power outlet.
Connecting the FM Antenna
Using the Supplied Wire Antenna
FM wire antenna
4
To assemble and connect the AM loop antenna
To assemble the AM loop antenna
To connect the AM loop antenna
Make sure to connect the wire correctly.
1 Hold
2 Insert
3 Release
• If the AM loop antenna wire or speaker cords are covered with vinyl, remove the vinyl to expose the tip of the antenna by
twisting the vinyl.
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the
antennas away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor
reception.
For better FM/AM reception
AM loop antenna
Keep it connected.
Outdoor FM
antenna
(not supplied)
AM
LOO
P
AM
EXT
Vynile-covered wire (not supplied)
Extend it horizontally.
GND
Disconnect the supplied FM antenna, and connect to an outdoor FM antenna
using a 75 Ω wire with coaxial type connector.
5
To Connect the Speaker Cords
Make sure the both speakers are connected correctly and firmly.
Right side (rear view)
Left side (rear view)
Gray
Gray with
black stripe
Gray
Gray with
black stripe
3 Release
1 Hold
2 Insert
When connecting the speaker cords, match the polarity of the speaker terminals: The cord with black stripe to (–), the cord
without stripe to (+).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.
Connecting to the Wall Outlet
Plug the AC power cord only after all connections are complete.
Now, your System is at your command!
DEMO Mode
When the System is connected to the wall outlet, a DEMO mode displaying some of the system’s features automatically starts.
To cancel DEMO display
While displaying the DEMO mode...
• To display the DEMO mode again, press and hold CANCEL/DEMO for 2 seconds.
While the System is turned on, the DEMO display will automatically starts if no operation is made for 2 minutes.
6
Before Operating the System
Parts Index
The numbers refer to the pages in which the parts are explained.
Remote control
9, 25
24, 25
9, 12, 19-22
9, 14
9-11
16
9, 12, 13, 21, 22
9, 10, 12, 14, 21, 22
9, 10
9, 10, 12, 14, 21, 22
16
16
9, 12, 13, 21, 22
9, 11-13, 21, 22
21-23
9, 12, 21
9, 15
16
9, 17-20
9, 16
Main unit
8
16, 24, 25
Remote sensor
9, 12, 13, 21, 22
9-11
9
9, 17, 18, 20
9, 25
9
16
17-19
17, 20
10, 12
17
9
7
11, 23
11
6, 16, 21, 22, 24, 25
10, 13, 16, 19, 21, 24, 25
9, 14
9, 11-13, 21, 22
9, 15
16
21-23
9, 12, 13, 21-23
9-12, 14, 16, 19-22, 24, 25
9, 16
14
15
The indications on the display teach you a lot of things while you are operating the System.
Before operating the System, be familiar with when and how the indicator illuminates on the display.
1
2
3
4 5
1 Timer indicators
• DAILY: Lights when Daily Timer stands by; flashes
while working.
• SLEEP: Lights when Sleep Timer is activated.
2 TRACK/GROUP mode indicators
• TRACK: Lights when disc (CD, MP3 disc, WMA disc)
is detected.
• GROUP: Lights when programming group in MP3/
WMA mode.
6
7
8
9 10
Indications on the main display
• While listening to radio:
• While listening to iPod
Band
Frequency
Source name
• While playing a CD:
Track number
• While selecting AUX:
Elapsed playing time
• While playing an MP3*/WMA:
MP3/WMA indicator lights accordingly
Current track
number
Elapsed
playing time
• While listening to XM
Satellite Radio:
Channel
number
Preset
number
CD:
When RESUME is ON,
RESUME is shown on the
display.
Total playing
time
MP3/WMA:
• In “TRACK” mode:
Total track number
4 Play mode indicator
• PRGM (program): Lights when Program Play mode is
activated.
5 Disc tray indicators
• 1-3: Disc tray number.
• ( ): Tray indicator
– Lights when the disc is detected.
– Blinking while playing back a disc.
– Goes off when there is no disc in the tray.
6 SOUND TURBO indicator
• Lights when the SOUND TURBO is activated (see
page 16).
7 SOUND MODE indicator
• Lights when the SOUND MODE is activated (see
page 16).
• While disc play is stopped:
Total track
number
3 MP3/WMA indicators
• MP3: Lights when MP3 file is detected.
• WMA: Lights when WMA file is detected.
• In “GROUP” mode:
Total group
number
Total track
number
8 Play mode indicator
• RNDM (random): Lights when Random Play mode is
activated.
9 FM reception indicators
• MONO: Lights while the FM monaural mode is
activated.
• ST (stereo): Lights while an FM stereo station with
sufficient signal strength tuned in.
p Play mode/Search mode indicators
• REPEAT: Lights when Repeat mode is activated (see
page 23).
– 1: Repeats the one track.
– 1DISC: Repeats the one disc.
– ALL: Repeats all the discs.
• ALL: Lights when ALL SRCH (All Search) is selected
for XM Satellite Radio.
* When you start playing an MP3 disc, the group number,
track number, track name, (and ID3 Tag) will be shown
before the elapsed playing time appears.
8
Daily Operations—Playback
1
The STANDBY lamp on the main unit turns off.
• Without pressing STANDBY/ON
, the System
turns on by pressing one of the source selecting
buttons in the next step.
1
2
Numeric keys
2
3
4
Disc selection keys
MP3/WMA MODE
3
Select the source.
Playback automatically starts if the selected source is
ready to start.
• If you press AUX, start playback source on the
external component.
FM MODE
4, 7, ¢
Turn on the power.
Adjust the volume.
Operate the target source as explained
later.
To turn off (standby) the System
The STANDBY lamp on the main unit
lights up.
• A small amount of power is always
consumed even while on standby.
How to Select Numbers
1
2
3
4
5
6
7
8
9
0
10
Examples:
To select number 5, press 5.
To select number 15, press
10 → 1 → 5.
To select number 30, press
10 → 3 → 0.
To select number 125, press
10 twice → 1 → 2 → 5.
To turn off the clock indication to save the
power—ECO mode
Main Unit
ONLY
While the System is turned off...
• Press the button again, to display the
clock indication.
For private listening
Connect a pair of headphones to the PHONES jack on the
main unit. The sound will no longer come out of the
speakers. Be sure to turn down the volume before
connecting or disconnecting the headphones.
• Disconnecting the headphones will activate the
speakers again.
DO NOT turn off (stand by) the System with
the volume set to an extremely high level;
otherwise, the sudden blast of sound can
damage your hearing, speakers and/or
headphones when you turn on the System or
start playback.
9
Listening to the Radio
To preset the stations
To select the band (FM or AM)
You can preset 30 FM and 15 AM stations.
FM
1 Tune in to a station you want to preset.
2 Activate the preset number entry mode.
AM
To tune in to a station
While FM or AM is selected...
Remote control:
Main unit:
1 sec.
1 sec.
3
4
• Finish the following process while the indication on the
display is flashing.
Select a preset number for the station you store.
See “How to Select Numbers” on page 9.
• You can also use 4/¢ on the main unit.
Store the station.
Frequency starts changing on the display.
When a station (frequency) with sufficient signal strength is
tuned in, the frequency stops changing.
• When you repeatedly press the button, the frequency
changes step by step.
To stop searching manually, press either button.
If the received FM station is hard to listen
Remote
ONLY
MONO
Canceled
memo
MONO:
Reception will improve though stereo
effect is lost. MONO indicator lights up.
• If you preset a station set to MONO, the station is stored
with the MONO setting.
10
Main Unit
ONLY
To tune in to a preset station
To insert a disc
1 Select a band (FM or AM).
You can insert discs while playing another source.
FM
AM
2 Select a preset number for the station you store.
See “How to Select Numbers” on page 9.
• You can also use 4/¢ on the main unit.
Playing Back a Disc
Playable media and files
This System can play back following types of media and
files.
Media
File format
Audio CD
Audio CD, CD-R/RW
MP3, WMA
CD-R
CD-RW
• Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply
with the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc on
this product may not be recommended.
• Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries.
11
To place the next CD, press DISC SKIP on the main unit.
When you press the button, the tray turns for the next CD.
To close the disc tray, press CD 0 again.
• When the disc tray is open, pressing CD 6 closes the tray
and the playback starts.
• You can load CDs while listening to the other source or
while listening to the CD being played back.
• When power is turned off with the tray opened, the tray is
automatically closed.
• If the CD cannot be read correctly (because it is scratched,
for example), “NO DISC” appears on the display.
Remote
ONLY
Changing the MP3/WMA Playback Mode
To select a disc to be played back
According to the MP3/WMA playback mode, 4/¢ or
numeric keys work for the group selection or the track
selection.
Examples:
When the MP3 play back mode is “GROUP.”
• The same operation can be
carried out using CD1 to CD3 on
the system.
To start:
To pause:
To stop:
GROUP indicator
Total group number
Total track number
To select a track/group*
You can change the MP3/WMA playback
mode by pressing MP3/WMA MODE.
• Each time you press the button, the MP3/
WMA playback mode changes as follows:
TRACK
To release, press
again.
Increases the track/
group* numbers.
Decreases the track/
group* numbers.
GROUP
TRACK:
4/¢, and numeric keys work for the
track selection of the MP3/WMA discs.
GROUP:
4/¢, and numeric keys work for the
group selection of the MP3/WMA discs.
Numeric keys works for selecting the track
number within the group.
• You can also use 4/¢ on the main unit.
* For details about the group selection, see “Changing the
MP3/WMA Playback Mode” on this page.
To locate a track directly and start to play
Using the numeric keys, you can directly select the track on
the currently selected CD. See “How to Select Numbers” on
page 9.
To Locate a Particular Portion
MP3/WMA groups/tracks configuration
This System plays back MP3/WMA tracks as follows.
Fast-forwards the track.
Hierarchy
Level 1
Level 2
Level 3
Level 4
01
03
04
ROOT
02
01
1
7
4
8
5
2
6
Level 5
9
3
1
While playing a disc, press and hold until the portion you
want is reached.
05
10
Fast-reverses the track.
• You can also use 1/Á on the main unit.
11
12
Group with its play order
MP3/WMA track with its play
order
12
Resume Play for Audio CD/MP3/WMA
If you press 7 during playback, the position of the track
where you stopped playback will be memorized by the
unit.
By pressing CD 6, you can start playback again from
the point where you stoppped it.
To activate/cancel resume play
Main Unit
ONLY
When the source is a CD...
2 sec.
memo
• Changing the disc by pressing the disc selection keys
will erase the track number for resume play.
• To play back from the first track while resume play is
activated, press 7 twice during playback then press
CD 6.
Playing back from iPod
This system is equipped with an iPod terminal on the front
panel. You can connect your iPod to this terminal and enjoy
the sound from your iPod.
• Remember you cannot send any data to your iPod from
this system.
memo
• The iPod battery is charged while the System is turned on
and STANDBY (except in ECO mode). See the iPod
instruction manual about battery charging.
• Sound distortion may occur when playing back audio
sources with high recording levels. When distortion
occurs, it is recommended to turn off the equalizer of the
iPod. For information on operating the iPod, see the iPod
instruction manual.
• JVC is not responsible for any loss of or damage to iPod
that might result from the use of this product.
• When you connect your iPod to the cable, make sure it
connects all the way in.
• Remove the iPod from the cable when you do not use.
• Do not carry the System with iPod connected. You might
drop it down or it might cause damages to the connector
part.
• Do not touch or hit the iPod terminal pins or the connecter
pins directly. It might cause damages to the connector part.
• Compatible iPod types:
iPod nano 1GB/2GB/4GB
iPod nano (2nd Generation) 2GB/4GB/8GB
iPod mini 4GB/6GB
iPod (4th Generation) 20GB/40GB
iPod photo (4th Generation) 20GB/30GB/40GB/60GB
iPod video (5th Generation) 30GB/60GB/80GB
If the iPod does not play correctly, please update your iPod
software to the latest version.
• For details about updating your iPod, check on the
Apple web site
<http://www.apple.com>.
iPod is a trademark of Apple Computer, Inc.,
registered in the U.S. and other countries.
13
To Connect iPod
Connect the iPod to the System using the supplied cable.
Make sure the System is turned off when you connect it.
To playback sounds on the iPod
To start:
To pause:
1 Connect the arrow of iPod terminal and the arrow of
the connector facing each other.
To select a track
Increase the track
numbers
Decrease the track
numbers
To Locate a Particular Portion
2 With the iPod and the circle on the connector facing
While playing iPod, press and hold until the portion you
want is reached.
up, squeeze the buttons on the sides, and insert it into
the iPod.
Fast-forwards the track.
Fast-reverses the track.
To set iPod sleep
Press and hold the button for a few seconds until iPod goes
to sleep.
You can place the
iPod on the supplied
stand for iPod.
memo
• Always set volume to “VOL MIN” when connecting or
disconnecting iPod.
When disconnecting the iPod, make sure that the System is
turned off.
To remove the
connector from your
iPod, squeeze the
buttons on the sides and
pull.
14
Playing Back from other equipment
To connect other equipment
By using an stereo mini plug cord (not supplied), you can
connect equipment with analog audio output jacks such as a
Digital Audio Player, or a TV, etc.
Stereo mini plug cord (not supplied)
Portable audio
device,
Game machine, etc.
AUX
(front panel)
If the audio output on the other equipment is not stereo
mini plug type,
Use a plug adapter to convert the stereo mini plug to the
corresponding plug of the audio output.
Refer to the manuals supplied with the other equipment.
memo
• Always set volume to “VOL MIN” when connecting or
disconnecting the other equipment.
To select other equipment for the source
15
Daily Operations – Sound & Other Adjustment
Adjusting the Volume
Setting the Clock
You can adjust the volume level to MIN, 1-30, MAX.
Remote control:
Main unit:
Main Unit
ONLY
Without setting the built-in clock, you cannot use the Daily
Timer (see page 24).
• To exit from the clock setting, press CLOCK/TIMER as
required.
• To go back to the previous step, press CANCEL/DEMO.
1 Activate the clock setting mode.
VOLUME
Remote
ONLY
To drop the volume in a moment
To restore the volume, press again, or
adjust the volume level.
FADE
MUTING
Adjusting the Sound
To emphasize the sound—SOUND TURBO
This function emphasizes the sound.
S-TURBO
2
• If you have already adjusted the clock before, press the
button repeatedly until the clock setting mode (see
page 24) is selected, then press SET/RESUME.
Adjust the hour.
OFF
(Canceled)
Sound Mode
You can select one of 3 SEA (Sound Effect Amplifier)
modes. You can use this effect only for playback.
ROCK
3 Adjust the minute.
POP
FLAT
CLASSIC
(No sound effect)
ROCK
Boosts low and high frequencies.
Good for acoustic music.
POP
Good for vocal music.
CLASSIC
Set for wide and dynamic sound stereo
systems.
FLAT
No sound effect applies.
“CLOCK OK” appears and the built-in clock starts
working.
To check the current time during play
Remote
ONLY
Clock
Source information
If there is a power failure
The clock loses the setting and is reset to “AM 12:00.” You
need to set the clock again.
16
Advanced Radio Operations
Numeric keys
XM
CHANNEL UP
¢
CHANNEL DOWN
XM DISPLAY
XM
DIRECT
XM DISPLAY
4
CATEGORY +/CHANNEL +/SEARCH MODE
PRESET +/-
About XM Satellite Radio
XM Satellite Radio is a satellite radio service with
digitalquality sound and over 170 digital channels, the most
commercial-free music in satellite radio services, live concerts
plus exclusive original programming, the biggest names in
news, talk, and entertainment, the most sports play-by-play
including Major League Baseball®. For the latest channel
listings and programming information, or to sign up, visit
<http://www.xmradio.com>.
XM Ready® is a registered trademark of XM Satellite
Radio Inc. All rights reserved.
Major League Baseball® is a registered trademark of Major
League Baseball Properties, Inc.
Preparation
Connecting the XM Mini-Tuner System (XM Mini-Tuner and XM Mini-Tuner Home Dock)*
To enjoy XM Satellite Radio, connect the XM Mini-Tuner System (not supplied) to the main unit.
* You can also use the conventional XM Connect and Play Digital Antenna (not supplied) for the main unit.
XM Mini-Tuner
(not supplied)
XM Mini-Tuner Home Dock
(not supplied)
17
Antenna Aiming
For XM Mini-Tuner Home Dock (not supplied) installation.
memo
• Place the XM Mini-Tuner Home Dock near a south-facing
window or where “Channel 1” can be heard clearly (see
below).
• Make sure there is no obstruction between the XM MiniTuner Home Dock and the sky.
For listening to XM Satellite Radio, you need the following:
• The XM Mini-Tuner System*1 (not supplied)—XM
Mini-Tuner and XM Mini-Tuner Home Dock
• Subscription to XM Satellite Radio*2
*1 To connect the XM Mini-Tuner System with the main
unit, see page 17.
*2 The following channels are available without subscription:
• Channel 0: This channel is for checking the XM Satellite Radio ID code.
• Channel 1: This is “XM Preview” channel.
While selecting XM...
Remote
control:
2 sec.
Main unit:
2 sec.
“A.AIMING” briefly appears on the display.
Then the status is indicated in 5 levels (from 0 to 4).
Position the XM antenna to get the highest signal strength,
either Satellite or Terrestrial. Signal levels of at least 3
should provide reliable reception. The most reliable
reception is achieved when signal levels of at least 3 on both
Satellite and Terrestrial. Terrestrial coverage is available
only in large metropolitan cities.
How to subscribe
XM Satellite radio is a subscription service. To subscribe to
the XM Satellite Radio, visit the XM Satellite Radio’s web
site at <http://xmradio.com/activation/>, or you can call 1800-XM-RADIO (1-800-967-2346). For subscription, you
need to have the XM Satellite radio ID code. To check the
ID code, follow the procedure below:
How to check the XM Satellite Radio ID code
Satellite signal levels
Terrestrial signal levels
• For details about XM Mini-Tuner Home Dock, see XM
Mini-Tuner Home Dock instruction manual.
After connection:
1 Select XM as the source.
Remote
control:
Main unit:
Listening to the XM Satellite Radio
To select XM as the source
Remote
control:
Main unit:
2 Tune in to “Channel 0.”
The display shows “CH000”, then shows “RADIO ID”
and the 8-digit (alphanumeric) ID code alternately.
Remote control:
Main unit:
The last received channel is tuned in.
“XM” appears and then the channel number appears on
the display.
Channel number
18
Remote
ONLY
To tune in to channels
Direct Channel Access
You can tune in to the desired channel directly by entering
the channel number.
1 Select “ALL SRCH.”
The ALL indicator lights up.
1 Press DIRECT.
ALL SRCH
CAT SRCH
2 Press the numeric keys to enter the desired channel
number while the channel number position is
flashing.
• To use the numeric keys, see “How to Select Numbers”
on page 9.
ALL indicator
2 Select the channel.
Remote control:
Main unit:
Using preset tuning
You can preset up to 30 channels.
To store the preset channels
Category Search
You can select the channel category and tune in to only the
channels included in the selected category.
1 Tune in to the channel you want to preset.
2 Activate the preset number entry mode.
1 Select “CAT SRCH.”
ALL SRCH
CAT SRCH
2 Select the channel category.
3
4
3
• Finish the following process while the indication on the
display is flashing.
Select a preset number for the channel you store. See
“How to Select Numbers” on page 9.
• You can also use 4/¢ on the main unit.
Store the channel.
The channel with the smallest channel number in the
category is displayed.
Select the channel.
Remote control:
Main unit:
The selected channel is tuned in after a few seconds.
5 Repeat steps 1 to 4 until you store all the desired
channels.
19
To tune in a preset channel
CH--- P--*
Channel number/Preset number
*Preset number is displayed only for
the channels which are preset.
CH NAME
Channel name
NAME
Artist name/feature
TITLE
Track/program title
CATEGORY
Category name
SIGNAL
Signal strength
1 Select XM as the source.
Remote
control:
Main unit:
2 Select a preset number for the channel you store.
See “How to Select Numbers” on page 9.
• You can also use 4/¢ on the main unit.
When SIGNAL is selected, current signal strength is
indicated on the display in 4 levels (NO SIGNAL, 1-3).
Changing the channel information
While listening to the XM Satellite Radio, the currently
selected channel information appears on the display.
You can change the type of channel information.
CH--- P--*
CH NAME
SIGNAL
NAME
CATEGORY
TITLE
memo
• Last channel you were listening to will be displayed the
next time you selected XM.
• When you tune in to another channel, the selected channel
number appears on the display.
• When all the text information cannot be shown on the
display at a time, the text scrolls.
• Some characters cannot be displayed correctly.
Messages on the display
When problems occur, a message appears on the display. In this case, refer to the following solution.
Possible cause
Solution
NO SIGNAL
Signals are too weak.
Move the XM Mini-Tuner Home Dock near
a south-facing window or where “Channel 1”
can be heard clearly.
CHECK
The XM Mini-Tuner is not properly in- Confirm the XM Mini-Tuner is fully seated
stalled or the cable is not properly con- in the XM Mini-Tuner Dock.
nected.
Then check the connection (see page 17),
and confirm the XM Mini-Tuner Dock cable
is not damaged and fully seated in the XM
terminal jack on the unit front panel.
↔
Message
XM TUNER
↔
CHECK
ANTENNA
The XM antenna is disconnected from Confirm the XM antenna is properly conthe XM Mini-Tuner Dock.
nected to the XM Mini-Tuner Dock (see
page 17).
LOADING
This receiver is loading the channel in- It takes a few minutes to complete. Wait until
formation and audio data.
loading is finished.
OFF AIR
Selected channel is not currently broad- Select another channel.
casting any signal.
UPDATING
The latest encryption code is being up- Wait until updating is finished.
dated.
“---”
No text information for the selected
channel is available.
—
“CH---”
Selected channel does not exist or is not
subscribed yet.
—
20
Advanced Disc Operations
Numeric
keys
CD Open/
Close 0
¢
CD1-CD3
7
4
CD1-CD3
DISC SKIP
CANCEL/DEMO
SET/RESUME
CD 6
¢
REPEAT
PROGRAM
RANDOM
CD 6
MP3/WMA
MODE
REPEAT
PROGRAM
RANDOM
7
4
Programming the Playing Order—Program Play
You can arrange the playing order of the tracks (up to 32)
before you start playback.
• You can repeat all the programmed tracks by pressing
REPEAT.
• During the PRGM indicator is shown on the display, you
cannot open the disc trays.
4
5
See “How to Select Numbers” on page 9.
• To use 4/¢ on the main unit, press SET/RESUME
after selecting tracks.
Repeat steps 2 and 3 to program the other tracks.
• To select a track from the same disc, repeat step 3.
Start playback.
The tracks you have selected are
played back in the order you
have programmed.
1 Before starting playback, press PROGRAM.
To skip a track:
2 Select a disc by pressing CD 1–CD 3.
3 Select tracks you want for Program Play.
To pause:
To stop:
To release,
press again.
• Tracks cannot be selected with the numeric keys during
Program Play.
Disc number
21
Track
number
Program step
To check the programmed contents
Remote
ONLY
While the PRGM indicator is shown on the display and
before playback.
In the programmed order.
In the reverse order.
To modify the program
While the PRGM indicator is shown on the display and
before playback.
To erase the last step:
To erase the entire
program:
To add steps in the program:
Repeat steps 2 and 3 on page 21.
To exit from Program Play
Playing at Random—Random Play
You can play back all the tracks on the selected disc at
random.
• You can repeat the current disc by pressing REPEAT.
1 Select a disc by pressing CD 1 – CD 3, then press 7.
2 Press RANDOM.
RANDOM
3 Start playback.
Playback starts in random order.
Random Play ends when all tracks are played.
To skip a track:
To pause:
To stop:
While the PRGM indicator is shown on the display and
before playback.
To release, press
again.
Pressing 7 also cancels Program Play.
• Tracks cannot be selected with the numeric keys during
Random Play.
To exit from Random Play
While the RAND indicator is shown on the display and
before playback.
RANDOM
22
Main Unit
ONLY
Playing Repeatedly—Repeat Play
Prohibiting Disc Ejection—Child Lock
You can repeat playback.
You can lock the disc trays so that no one can eject the
loaded discs.
For CD/MP3/WMA (TRACK mode):
While the disc trays are closed...
REPEAT
Canceled
(No indication)
For MP3/WMA (GROUP mode):
(at the same time)
REPEAT
Canceled
(No indication)
During Program Play:
REPEAT
Canceled
(No indication)
During Random Play:
REPEAT
Canceled
(No indication)
REPEAT 1
Repeats the current track.
REPEAT 1
DISC
Repeats all the tracks on the current disc.
(Selectable in Normal play and Random
play)
REPEAT
Repeats all the tracks in the current
group (for MP3/WMA playback) or
program.
REPEAT
ALL
23
Repeats all the discs.
To cancel the prohibition, repeat the same procedure.
“UNLOCKED” appears on the display.
Using the Timers
SLEEP
CANCEL/DEMO
SET/RESUME
CLOCK/TIMER
¢
4
Setting the Timer
Main Unit
ONLY
Using Daily Timer, you can wake up with music, etc.
• To exit from the timer setting, press CLOCK/TIMER as
required.
• To correct a misentry during the process, press CANCEL/
DEMO. You can return to the previous step.
1 Select ON TIME.
DAILY
Canceled
ON TIME
Clock setting
(see page 16)
How Daily Timer actually works
Once the Daily Timer has been set, the timer (
) and
DAILY indicators are lit on the display. Daily Timer is
activated at the same time everyday until the timer is
turned off manually.
When the on-time comes
The System turns on, tunes in to the selected station or
start playing the selected source, and sets the volume
level to the preset level.
• If “P – – –” is selected, the last tuned station is selected.
• If “VOL – –” is selected, the last specified value is
selected.
• If “DISC – –” is selected, the last played disc is
selected.
• While Daily Timer is working, the timer (
)
indicator flashes on the display.
• The timer setting remains in memory until you change
it.
• Without canceling the Daily Timer, you can change the
source or adjust the volume after Daily Timer starts
playback.
2 Make the timer setting as you want.
1 Set the hour then the minute for on-time.
2 Set the hour then the minute for off-time in the
same manner.
24
3 Select the playback source—“TUNER FM,”
“TUNER AM,” “CD,” “XM RADIO,” “iPod” or
“AUX IN.”
Main Unit
ONLY
To turn off the Timer after its setting is done
Since Daily Timer is activated at the same time everyday,
you may need to cancel it on some particular days.
1 Select DAILY.
DAILY
ON TIME
Canceled
Clock setting
(see page 16)
2 Turn off the selected Timer.
When selecting tuner: Select a preset number or
“P – – –” by pressing 4 or ¢, then press SET.
When selecting CD: Select a disc or “DISC – –” by
pressing 4 or ¢, then press SET.
4 Set the volume.
The display shows “OFF”, then the timer (
DAILY indicators are turned off.
) and
To turn on the Timer again, repeat the above steps and
press in step 2...
3
If you select “VOL – –,” the volume is set to the level
that was set before the power was turned off.
Turn off the System (on standby) if you have set the
timer with the System turned on.
The timer (
) and DAILY indicators are turned on.
To turn off the System after a certain period of
time—Sleep Timer
Remote
ONLY
1 Specify the time (in minutes).
SLEEP
10
20
30
60
90
120
OFF
memo
• Do not set to ECO mode after setting Daily Timer.
(Canceled)
2 Wait until the set time goes off.
To check the time remaining until the shut-off time
• If you press the button repeatedly, you can change the shutoff time.
25
Additional Information
Learning More about This System
Daily Operations—Sound & Other Adjustments
Daily Operations—Playback (see pages 9 to 15)
Adjusting the Volume:
Listening to the Radio:
• If you store a new station into an occupied preset number, the
previously stored station in that number will be erased.
• When you unplug the AC power cord or if a power failure
occurs, the preset stations will be erased in a few days. If this
happens, preset the stations again.
Playing Back a Disc:
• When using an 8 cm (3-3/16 inch) disc, place it on the inner
circle of the disc tray.
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– MP3/WMA discs are required a longer readout time than
regular CDs. (It depends on the complexity of the group/file
configuration.)
– Some MP3/WMA files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1 for
the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the letter
case—upper/lower).
– Some characters or symbols will not be shown correctly on
the display. The maximum character number shown on the
display is 32 (without the extension code) for files, and 30
for ID3 tag.
– It is recommended that you make each MP3 file at a
sampling rate of 44.1 kHz and at a bit rate of 128 kbps.
Similarly each WMA file at a sampling rate of 44.1 kHz and
at a bit rate of 96 kbps.
– This System can recognize the total of 255 files and folders.
Those exceeding the maximum number cannot be
recognized.
– Playback order of MP3/WMA tracks may be different from
the one you have intended while recording. If a folder does
not include MP3/WMA tracks, they are ignored.
(see pages 16)
• Be sure to turn down the volume before connecting or putting
the headphones.
Adjusting the Sound:
• This function also affects the sound through the headphones.
Setting the Clock:
• “AM12:00” will flash on the display until you set the clock.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, reset the clock.
Advanced Disc Operations (see pages 21 to 23)
Programming the Playing Order—Program Play:
• If you try to program a 33rd track, “FULL” appears on the
display.
• While programming steps...
Your entry will be ignored if you have tried to program an item
number that does not exist on the disc (for example, selecting
track 14 on a disc that only has 12 tracks).
Timer Operations (see pages 24 and 25)
• When you unplug the AC power cord or if a power failure
occurs, the timer will be canceled. You need to set the clock
first, then the timer again.
• If you set the Sleep Timer after Daily Timer starts playing the
selected source, Daily Timer is canceled.
When discs* in more than one tray are loaded on the disc
trays, they are played in sequence as follows:
Ex.: When CD 2 is selected:
CD 2 -> CD 3 -> CD 1 (then selects CD 2, and stops)
* When no disc is loaded on the tray, that disc number is
skipped.
You can exchange discs while playing or selecting another
disc.
26
Troubleshooting
If you are having a problem with your System, check this list
for a possible solution before calling for service.
General:
Adjustments or settings are suddenly canceled before
you finish.
] There is a time limit. Repeat the procedure again.
Operations are disabled.
] The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power cord
and then plug it back in.
Unable to operate the System from the remote control.
] The path between the remote control and the remote sensor
on the System is blocked.
] Point it at the remote sensor on the front panel.
] Signals cannot reach the remote sensor.
More closer to the System.
] The batteries are exhausted.
The iPod doesn't playback although the display indicates
“CONNECT”.
] The battery is empty. Let stand for more than approximately
ten minutes on the connecting condition.
Timer Operations:
Daily Timer does not work.
] The System has been turned on when the on-time comes, or
set to ECO mode after setting Daily Timer. Timer starts
working only when the System is turned off (Standby).
Maintenance
To get the best performance of the System, keep your discs,
and mechanism clean.
Handling discs
• When removing the disc from its case, hold it at the edge while
pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the disc.
• Put the disc back in its case after use to prevent warping.
• Be careful not to scratch the surface of the disc.
• Avoid exposure to direct sunlight, temperature extremes, and
moisture.
To clean the disc:
Wipe the disc with a soft cloth in a straight line from center to
edge.
Cleaning the System
No sound is heard from the speakers.
] Speaker connections are incorrect or loose (see page 6).
] Headphones are connected (see page 9).
“PROTECT”appears on the display, then the power goes
off.
] The speaker wire leads come in contact with each other.
Check the connection and make corrections (see page 6).
Radio Operations:
Hard to listen to broadcasts because of noise (see pages 4
to 5).
] Antennas connections are incorrect or loose.
] The AM loop antenna is too close to the System.
] The FM antenna is not properly extended and positioned.
Disc/iPod Operations:
The disc does not play.
] The disc is placed upside down. Place the disc with the label
side up.
The disc sound is discontinuous.
] The disc is scratched or dirty.
The disc tray does not open or close.
] The AC power cord is not plugged in.
] Child Lock is in use (see page 23).
27
• Stains should be wiped off with a soft cloth. If the System is
heavily stained, wipe it with a cloth soaked in water-diluted
neutral detergent and wrung well, then wipe clean with a dry
cloth.
• Since the System may deteriorate in quality, it become
damaged or get its paint peeled off, be careful about the
following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it strongly.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as insecticides
to it.
– DO NOT allow any rubber or plastic to remain in contact for
a long time.
Power Specifications
Specifications
Power Requirements
Power Consumption
Amplifier
Output Power
200 W per channel, min. RMS, driven into 6 Ω at 1kHz, with
no more than 10% total harmonic distortion
Terminals
AUX IN
Input Sensitivity/Impedance(1 kHz) 400 mV/50 kΩ
Speaker terminals
6 Ω - 16 Ω
Phones
32 Ω - 1 kΩ
17 mW/ch output into 32 Ω
iPod
Compatible iPod types See page 13
Bus Power supply
Max.5 V/500 mA
XM
Bus Power supply
Max.5V-5.5V/500mA
AC 120 V
60 Hz
180 W (power on mode)
24 W (in Standby mode, with iPod
disconnected)
33 W (in Standby mode, with iPod
connected)
1 W (in ECO mode)
Design and specification are subject to change without notice.
CD Player
CD Capacity
Dynamic Range
Signal-To-Noise Ratio
Wow And Flutter
3 CDs
85 dB
85 dB
Unmeasurable
Tuner
FM Tuner
Tuning Range
AM Tuner
Tuning Range
87.5 MHz - 108.0 MHz
530 kHz - 1 710 kHz
Unit
Dimensions
Mass
270 mm × 307 mm × 492mm (W/H/
D) (10-11/16" × 12-1/8" × 19-3/8")
Approx. 8.7 kg (19.2 lbs)
Speaker Specifications (each unit)
SP-MXKC58
Type
3-way bass-reflex type
Speaker Unit Woofer: 16 cm (6-5/16") cone × 1
Mid:
5cm (2") cone × 1
Tweeter: 2 cm (13/16") dome × 1
Power Handling Capacity 200 W
Impedance
6Ω
Frequency Range
45 Hz - 22 000 Hz
Sound pressure level 87 dB/W·m
Dimensions
220 mm × 324 mm × 238 mm(W/H/
D) (8-11/16" × 12-13/16" × 9-3/8")
Mass
Approx. 3.6 kg (8 lbs)
Accessories
See page 4
28
TO OUR VALUED CUSTOMER
THANK YOU FOR PURCHASING THIS JVC PRODUCT.
WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE.
NEED HELP ON HOW TO HOOK UP?
NEED ASSISTANCE ON HOW TO OPERATE?
NEED TO LOCATE A JVC SERVICE CENTER?
LIKE TO PURCHASE ACCESSORIES?
IS HERE TO HELP!
TOLL FREE: 1(800)252-5722
http://www.jvc.com
Remember to retain your Bill of Sale for Warranty Service.
Do not attempt to service the product yourself
Caution
To prevent electrical shock, do not open the cabinet.
There are no user serviceable parts inside.
Please refer to qualified service personnel for repairs.
BT-51018-5
(0306)
LIMITED WARRANTY
1-1 USA ONLY
ONLY FOR PRODUCT PURCHASED IN U.S.A.
JVC Americas Corp. (JVC) warrants this product and all parts thereof, except as set forth below ONLY TO THE
ORIGINAL RETAIL PURCHASER to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of
original purchase for the period shown below. ("The Warranty Period")
PARTS
1
LABOR
YR
1
YR
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND
IN THE COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective within the warranty period, JVC will repair or replace defective parts with new or
rebuilt equivalents at no charge to the original owner. Such repair and replacement services shall be rendered by JVC
during normal business hours at JVC authorized service centers. Parts used for replacement are warranted only for the
remainder of the Warranty Period. All products may be brought to a JVC authorized service center on a carry-in basis.
Color televisions with a screen size of 27" or greater qualify for in-home service. In such cases, a technician will come
to your home and either repair the TV there or remove and return it if it cannot be repaired in your home.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Please do not return your product to the retailer
Instead, return your product to the JVC authorized service center nearest you. If shipping the product to the service
center, please be sure to package it carefully, preferably in the original packaging, and include a brief description of
the problem(s). Please call 1-800-252-5722 to locate the nearest JVC authorized service center. Service locations
can also be obtained from our website http://www.jvc.com. If your product qualifies for in-home service, the service
representative will require clear access to the product.
If you have any questions concerning your JVC Product, please contact our Customer Care Center at 800-252-5722
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty
installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by
JVC to render such service, or if affixed to any attachment not provided with the products, or if the model or serial
number has been altered, tampered with, defaced or removed;
2. Initial installation, installation and removal from cabinets or mounting systems.
3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. User Removal Memory Devices/Video Pick-up Tubes/CCD Image Sensors are covered for 90 days from the date of purchase;
7. Accessories;
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);
9. Products used for commercial purposes, including, but not limited to rental.
10. Loss of data resultant from malfunction of hard drive or other data storage device;
There are no express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS
LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR ANY LOSS OF USE OF THE PRODUCT, INCONVIENCE, OR ANY OTHER
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTAL (INCLUDING, WITHOUT LIMITATION,
DAMAGE TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT
OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE
WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an
implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
JVC AMERICAS CORP.
1700 Valley Road, Wayne, New Jersey 07470
http://www.jvc.com
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAIL
OF REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY
INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet.
Retain this information for future reference.
Model No. :
Serial No. :
Purchase date :
Name of dealer :
MX-KC58 COMPACT COMPONENT SYSTEM
EN
© 2007 Victor Company of Japan, Limited
0107NYMCREBET