HEC-RX1 INSTRUCTION MANUAL Relaxation Chair CONTENTS

HEC-RX1 INSTRUCTION MANUAL Relaxation Chair CONTENTS
INSTRUCTION MANUAL
Relaxation Chair
HEC-RX1
CONTENTS
PAGE
IMPORTANT SAFETY INSTRUCTIONS ……… 1 ∼ 4
NAME/FUNCTION OF EACH PART ……… 5 ∼ 6
HOW TO PLACE THE CHAIR …………………… 7
HOW TO INSTALL THE HEAD REST AND PILLOW ……… 8
PREPARATIONS PRIOR TO USE ……………… 8
ADJUSTMENT OF CHAIR ………………… 9 ∼ 10
PROGRAM OPERATION ………………………… 11
AFTER USE ………………………………………… 12
MAINTENANCE PROCEDURES ………………… 12
TROUBLE-SHOOTING …………………………… 13
SPECIFICATIONS ………………………………… 14
Be sure to read this manual thoroughly in order to ensure
proper use. In particular, make certain to read the section
"IMPORTANT SAFETY INSTRUCTIONS".
Keep this manual in a safe place so that it can be found easily.
9BF-6-P111-348AB-0 0807
IMPORTANT SAFETY INSTRUCTIONS
All of the following information is important.
Be sure to follow the instructions carefully.
When using an electrical appliance, basic precautions should always be followed, including the
following:
Read all instructions before using this appliance:
Do not allow any children to use the chair, play on or around it. Also, while in use, keep children
away from the chair.
Otherwise, an injury may occur.
DANGER
Be sure to check that there is no-one (children in particular), or any pets under the foot rest prior to
lowering the foot rest. In addition, do not leave the foot rest in the raised position when not in use.
Otherwise, an injury may occur.
To reduce the risk of electric shock:
Always unplug this appliance from the electrical outlet immediately after using and before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:
Handling the cord on this product or cords associated with accessories sold with this product, will
expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after handling.
An appliance should never be left unattended when plugged in. Unplug from outlet when not in use,
and before putting on or taking off parts.
Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or
injury to persons.
Close supervision is necessary when this appliance is used by, on, or near children, invalids, or
disabled persons. Keep children away from extended back, foot support (or other similar parts).
Use this appliance only for its intended use as described in this manual. Do not use attachments not
recommended by the manufacturer.
Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has
been dropped or damaged, or dropped into water. Return the appliance to a service center for
examination and repair.
Do not carry this appliance by supply cord or use cord as a handle.
Keep the cord away form heated surfaces.
Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair,
and the like.
Never drop or insert any object into any opening.
Do not use outdoors.
Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
To disconnect, turn all controls to the off position, then remove plug from outlet.
Connect this appliance to a properly grounded outlet only. See Grounding Instructions.
Be sure to check that there is no-one (children in particular), or any pets around the chair prior to
adjusting the back rest or foot rest.
Otherwise, an injury may occur.
Do not attempt to stand on the arm rest, foot rest, or back rest.
Otherwise, the user may fall over, resulting in injury.
Be careful not to use the chair when the cord or the power plug is damaged or the outlet is loose.
Otherwise, electric shock, short circuit or fire may occur.
The following persons are requested to consult a doctor prior to use.
Otherwise, the user may feel sick or an injury may occur.
Those who are undergoing medical treatment and particularly those who complain of indisposition
Those who have malignant tumors
Those who suffer from heart trouble
Those who are in menstrual period or pregnant
Those who require complete rest
Those whose spine is abnormal or bent
Those who desire to use the chair on a part of the body that was previously diseased or receiving
medical treatment
Those who are feverish (38℃(100 ℉ ) or over)
Those who have weak bones (osteoporosis etc.)
Those who use a medical electronic device implanted into the body (e.g. a pacemaker)
Those who have a serious blood circulation disorder in the legs
Never attempt to dismantle the chair. Do not allow any personnel other than a qualified repair
technician to dismantle or repair the chair.
Otherwise, fire, electric shock or injury may occur. Ask the sales agent if repairs are required.
Do not attempt to damage, break, modify, bend forcibly, pull, twist or bundle the cord.
In addition, do not place heavy objects on the cord or jam the cord between objects.
Otherwise the cord may break, resulting in fire or electric shock.
Do not use the chair at any current other than the designated voltage.
Otherwise, fire or electric shock may occur.
Be sure to disconnect the power plug from the outlet prior to maintenance. Also, do not attempt to
plug/unplug the power plug with wet hands.
Otherwise, injury or electric shock may occur.
Be careful not to spill water over the chair.
Otherwise, electric shock, short circuit or fire may occur.
Do not suddenly release your hand, while raising the foot rest manually.
Otherwise, an injury may occur.
Prior to use, be sure to check that the cover cloth or the cloth of other parts is not torn. If a tear is
found, stop using the chair immediately, unplug the power source, and obtain service.
If the chair is used with torn cloth, it may result in injury or electric shock.
Be careful not to put your hand or foot into the space between the back rest and arm rest or into the
space at the underside of the back rest or into the space under the foot rest or into the space between
the arm rest and side cover or into the space between the back rest and head rest.
Otherwise, an injury may occur.
Use only under careful medical supervision if you have or there is a possibility that you have a
medical condition that may possibly, in any way, be affected by chair.
Do not wind the power cord around the main unit.
Moreover, be careful not to operate the back rest with the cord hooked on an obstruction.
Otherwise, unreasonable force may be applied to the cord, possibly resulting in fire or electric shock.
If discomfort or pain is felt during use, stop using the chair and consult a doctor immediately. In
addition, when the force is felt strongly, stop using it earlier than planned.
Otherwise, if the user continues using in such a way, an unexpected accident may occur.
1
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING
After use, be sure to set the POWER switch to the [OFF] position.
Otherwise, it may result in accident or injury due to a child's mischief.
Do not use the chair on top of a heated carpet, or near a stove or other heat sources.
Otherwise, it may result in fire.
Do not attempt to hang from the head rest, or pull the head rest forcibly.
Otherwise, the head rest may come off, possibly resulting in injury.
Aim to use the chair for up to 15 minutes each time.
Otherwise, the continuous use of the chair on one point for an extended period may result in adverse
effects or injury.
Be careful not to fall asleep during use.
Otherwise, an injury may occur.
Place the chair on a level floor surface.
Otherwise, if it is placed at an unstable place, the main unit may fall over, possibly resulting in injury.
Grounding Instructions
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord
having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate
outlet that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER
Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the product is
properly grounded. Do not modify the plug provided with the product – if it will not fit the outlet,
have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug
illustrated in sketch A in following figure. Make sure that the product is connected to an outlet having the
same configuration as the plug. No adapter should be used with this product.
GROUNDING METHODS
Sketch A
Do not use the chair in the bathroom, or places with high humidity.
Otherwise, electric shock may occur.
GROUNDED
OUTLET
Do not use the chair with bare skin.
Otherwise, an injury may occur.
Do not use for any purposes other than as a chair.
Otherwise, an accident or injury may occur.
Avoid use by those who are unable to clearly indicate their intentions, as well as by physically
disabled people.
Otherwise, an injury may occur.
Do not attempt to disconnect the power plug by pulling the cord, but always by holding the power
plug and pulling it out. Also, clean the dust off the power plug periodically.
Otherwise, electric shock, short circuit or fire may occur.
Switch the power [OFF] instantly if there is a power failure, and also pull the power plug out from the
outlet.
Otherwise, it may become dangerous when the power is restored.
Do not move the chair with a person on it.
Otherwise, the chair may fall over, resulting in injury.
GROUNDING
PIN
GROUND
OUTLET BOX
This appliance is intended for Household Use Only.
WARNING
This appliance is equipped with a PTC resetting protection device.
This is a safety feature to protect the appliance from overload. If the appliance should suddenly stop
and will not start, turn off the main switch and pull the plug off the socket outlet. Do not operate the
appliance for at least 30 minutes. Failure to turn the appliance off may result in the appliance starting
unexpectedly when the device resets.
Do not use the chair with other medical instruments (e.g. a low frequency medical instrument).
Otherwise, the user may feel sick or, it may cause other health problems.
If the chair becomes inoperative, disconnect the power plug immediately to prevent accidents, and
ask the sales agent for inspection/repair information.
Otherwise, it may result in fire due to electric shock, current leakage, short circuit, etc.
When the equipment will not be used for an extended period, be sure to disconnect the power plug
from the outlet.
Otherwise, it may result in electric shock, current leakage or fire due to damaged insulation.
The maximum permissible weight of the user is 120 kilograms(265 lbs).
Otherwise, an accident may happen or damage to the machine may result.
SAVE THESE INSTRUCTIONS
3
4
NAME/FUNCTION OF EACH PART
Control
Head rest
Pillow
ON/OFF lamp
Illuminates when the control is on.
Back rest
Seat
ON/OFF button
Used for switching the operation ON/OFF.
(See page 9) (See page 11)
Control
Arm rest
STOP button
Used if you have felt abnormal physical sensation
or want to stop the operation immediately.
(See page 11)
Foot rest
Cord
Power plug
PROGRAM SELECTION button
Used to select from two kinds of
courses "STRETCH" and
"RELAX".
(See page 11)
RELAX lamp
STRETCH lamp
Check the accessories
at first.
ZERO-G button
Used to set the back rest, foot rest, and
seat to prearranged reclining angles.
(See page 9)
Head rest
HOME POSITION button
Caster
Installation screws
(2 screws)
Used when moving the chair.
(See page 7)
LEG button
Adjusts the angle of the foot rest.
(See page 10)
Pillow
POWER switch
Used to turn on/off the power
source.
(See page 8) (See page 12)
5
Used to return the back rest, foot rest and
seat to home positions.
(See page 10)
RECLINING button
Adjusts the angle of the back rest, foot rest
and seat.
The back rest, foot rest and seat are moved
in conjunction with each other.
(See page 10)
6
HOW TO PLACE THE CHAIR
HOW TO INSTALL THE HEAD REST AND PILLOW
How to move the chair
1 Raise the back rest.
Movement becomes easier when the back
rest is raised. (See page 10)
the front side of the chair,
2 Raise
and move it using the casters.
the screws (x2)
1 Remove
from the head rest.
Head rest
inserting the head rest
2 After
into the pipe, secure the head
rest firmly with
the screws (x2).
Pipe
Head rest
PUSH
PULL
Hole
Screws
Back rest
the fastener of the back
3 Unzip
pad, and cover the back rest
Caster
NOTE
Before moving the chair, be sure to remove
the power plug from the outlet.
Be careful not to step on the power cord during
movement.
Be sure to move the chair with the assistance
of another person on an easily damaged floor
surface or concrete surface.
* Before moving the chair, make sure that the
head rest is securely attached. (See page 8)
* Be careful when moving the chair by holding
the head rest as doing so may cause the head
rest to tilt forward.
The chair can be carried by two persons with
each holding the arm rests on the left and the
right respectively. In this case, however, ensure
that the control is not raised.
with the back pad.
Back rest
fastener
It prevents damaging the floor, and
muffles the noise during use.
Back pad
Back pad
fastener
Back rest
To move the chair, one person should
hold the foot rest and the other should hold
the back rest with the back rest reclined.
the head rest and the
Place the pillow on the head
5 Secure
6
back pad with the hook and loop
rest.
fasteners.
Head rest
Head rest
Pillow
Back pad
there is sufficient space
2 Ensure
to allow the chair to recline.
In order not to touch the wall or other
things when reclined, allow a clearance
of 70 cm(28" ) or more to the front and
the back of the chair.
70cm(28") or more
Foot rest
70cm(28") or more
Back rest
Carpet
NOTE
Place the chair on a level floor surface.
Keep the chair at least 1 meter(3 ft) away from AV machines like a TV or radio.
Otherwise, the program may be disturbed by noise.
Do not keep the chair in a place with high humidity like a bathroom.
Do not keep the chair in a place where it will be exposed to direct sunshine for an extended
period, or in a place near a heater where the temperature may reach high levels.
7
up the fastener of the back
4 Zip
pad.
Foot rest
Decide where to place it
a carpet, etc. on the set-up
1 Lay
place.
Screws
Hook and loop
fasteners
PREPARATIONS PRIOR TO USE
1 Check the cloth of the chair.
Prior to use, be sure to check that the cover
cloth or the cloth of other parts is not torn.
If a tear is found, stop using the chair
immediately, unplug the power source, and
obtain service. If the chair is used with
torn cloth, it may result in injury or electric
shock.
3 How to connect the power source.
① Insert the power plug into an outlet.
② Set the POWER switch to the "ON"
position.
POWER switch
2 Check the power cord.
Check that there is neither breakage nor
damage to the cords.
Check that the cords are not caught between
the back rest and the arm rest, and that they
are not placed beneath the chair.
Press
8
ADJUSTMENT OF CHAIR
Before sitting on the chair
Bring all parts of the chair to
their home position by pressing
the RECLINING( ) button.
Sitting on the chair while the foot rest is being
raised is dangerous. Be sure to lower the foot
rest completely before sitting on the chair.
When adjusting to a favorite position
Keep the RECLINING button pressed until the desired angle is achieved.
Foot rest
Back rest
Press
NOTE
Do not attempt to climb onto or off the seat
by stepping on the foot rest. Do not attempt
to place anything on, or sit on the foot rest.
The user may fall over, resulting in an accident
or injury.
Adjustment range
Approx. 80゜
Be sure to check that there is no-one or any pets around the chair prior to adjusting
the back rest. It may result in an accident or injury.
Foot rest
Adjustment range
Approx. 35゜
the angle of the foot rest.
5 Adjust
Angle adjustment can be made for foot rest only.
Head rest
Keep the LEG button pressed until the desired angle is achieved.
Raise the foot rest by continuously
pressing the button.
3 Press the ON/OFF button.
When you press the button, the ON/OFF lamp illuminates.
Lower the foot rest by continuously
pressing the button.
Press
9
Foot rest
Adjustment range
Approx. 80゜
WARNING
Adjust the angle of the back rest, foot rest, and seat.
When the foot rest is suddenly released after being raised by hand, it will return forcibly to
the previous position. For safety, be sure to lower the foot rest slowly using your hand.
When adjusting to a comfortable position
Press the ZERO-G button.
When you press the button, the back rest, foot rest,
and seat are automatically adjusted to prearranged
reclining angles.
Reclining can be stopped during the reclining
motion by pressing either the ZERO-G button,
HOME POSITION button, RECLINING button,
LEG button, ON/OFF button, or STOP button.
* When the reclining motion is stopped by pressing
the ON/OFF button or STOP button, press the
ON/OFF button to resume the operation.
* When the reclining motion is stopped by pressing
buttons other than the ON/OFF button or STOP
button, press the desired button for motion.
Adjustment range
Approx. 40゜
NOTE
Choose the preferred angle by adjusting the head rest.
4
Foot rest
Back rest
The angle of the seat will be changed automatically
in accordance with the angle of the back rest.
For the sake of safety, depending on the angle,
the foot rest may go up once and then lower.
Sit deeply in the massage chair so that the
waist touches the back rest.
2 You can move the head rest forward.
115 ゜
Raise the back rest, and lower the foot rest by
continuously pressing the button.
1 Sit on the center of the chair.
Adjust the angle of head rest.
Recline the back rest, and raise
the foot rest by continuously
pressing the button.
Press
■ Angle is returned automatically to the home position
when the HOME POSITION button is pressed.
For the sake of safety, depending on the angle, the foot rest may go up once and then lower.
If you press the HOME POSITION button during use, operation will stop.
Posture suited for whole body
comfort
Foot rest
Press
Back rest
10
AFTER USE
PROGRAM OPERATION
1 Press the ON/OFF button.
When you press the button, the ON/OFF
lamp illuminates.
Press
the positions of the back
2 Adjust
rest and the foot rest.
(See page 9-10)
the button for the preferred
3 Press
program.
For firm pressure
For gentle relief
If you press the button for the current
program, operation will stop.
WARNING
Those who are receiving medical treatment or to
whom the following categories apply should consult
a doctor before using the chair.
Otherwise, the user may feel sick or an injury may
occur.
Those who are using self-contained medical
electronic equipment that is likely to be affected
by electromagnetic interference (e.g. a pacemaker)
Those who have malignant tumors
Those who suffer from heart trouble
Those who are in the early-pregnancy
period or in the post-delivery period
Those who suffer from sensory disturbance
caused by an advanced peripheral circulatory
disturbance
Those who have skin lesions
Those who require complete rest
Those who have a body temperature of
38℃(100 ℉ ) or more (at the fever stage)
Example: those who are suffering from strong
acute inflammation symptoms (fatigue,
chill, blood pressure change, etc.), and
from weakness
Those who suffer from osteoporosis, and from
acute painful conditions such as fracture of spine,
sprain, pulled muscle, etc.
Those whose spine is abnormal or bent
Those who desire to use the chair on a part
of the body that is diseased or receiving medical
treatment
The chair should not be used by those for whom
massage has been prohibited by a doctor.
Example: Those who suffer from thrombosis
(embolism), severe aneurysm, acute
varicose veins, various types of dermatitis,
skin infections (including inflammation of
subcutaneous tissue), etc.
When you want to suspend the
operation in the middle or have felt
some abnormality with your body
Press the ON/OFF button or the
STOP button.
Operation stops, and all the lamps
will extiguish.
11
After use, be sure to set the POWER switch to the [OFF] position.
When the equipment will not be used for an extended period, be sure to disconnect the power
plug from the outlet.
Turn off the POWER.
Bring all parts of the chair to
1 their
2
home position by pressing
If the ON/OFF lamp
the RECLINING(
①
) button.
Be sure to check that there are no children,
pets, or any obstacles around the chair.
has not turned off, press
the ON/OFF button.
② Set the POWER switch
to the [OFF] position.
Press
POWER switch
Foot rest
Press
Back rest
Press
MAINTENANCE PROCEDURES
WARNING
Be sure to disconnect the power plug from the outlet prior to maintenance.
NOTE
Do not attempt to use benzene, thinner, alcohol, alkaline detergent or bleaching agent for cleaning,
as this may result in deformation, discoloration or cracking.
■ Automatic timer.
Approx. 15 minutes later, operation will
stop, and all the lamps will extinguish.
CAUTION
CAUTION
If discomfort or pain is felt during use, stop using
the chair and consult a doctor immediately.
In addition, when the force is felt strongly, stop using
it earlier than planned.
Otherwise, if the user continues using in such a way,
an unexpected accident may occur.
Plan to use a program for up to 15 minutes each
time. Also, the total daily exposure should not be
more than 30 minutes.
Otherwise, the continuous use of the chair on one
point for an extended period may result in adverse
effects or injury.
Do not use the chair with bare skin.
Otherwise, an injury may occur.
Be careful not to fall asleep during use.
Otherwise, an injury may occur.
HEAD REST, BACK PAD, SEAT COVER, ARM REST, FOOT REST, PILLOW (Leather)
Perform daily maintenance by wiping with a soft dry cloth. When parts are badly soiled,
adopt the following maintenance procedure:
① Soak a soft cloth in diluted
neutral kitchen detergent,
and squeeze it well.
Wipe the main unit with
the damp cloth in
a tapping motion.
MAIN UNIT (Plastic parts and frame)
Soak a soft cloth in diluted neutral kitchen
detergent, and squeeze it well. Wipe the
main unit with the damp cloth, and wipe
it with a dry cloth afterwards.
② Soak a cloth in clean water, and
squeeze it well. Wipe off the remaining
detergent with the damp cloth.
③ Wipe it with a dry cloth afterwards.
* Do not force-dry with a drier.
* Do not make contact with vinyl products
for an extended period. It may cause
discoloration.
Control
Wipe with a soft dry cloth.
*Do not wipe with a damp cloth.
12
TROUBLE-SHOOTING
SPECIFICATIONS
WARNING
If the trouble still persists after following the proper countermeasures, stop using the chair to
avoid possible accidents. Disconnect the power plug from the outlet and consult the sales agent.
Do not attempt to repair the equipment at home by yourself, as it is very dangerous.
Sound and sensation during operation
During use, the following sounds or sensation may be unavoidably generated
because of its structure, but they are not problems.
(They will not affect the function, etc.)
・Sound of air bags
"Pusshu" sound (Change valve sound)
Hissing sound (Exhaust sound)
"Buu" sound (Sound of pump operation)
"Pako" sound (Sound when the air bag fills out)
Type of Trouble
Operation failure
・Wobbling foot rest and seat
・Unsteadiness when reclining
・"Gee" sound when reclined
・"Gee" and "Bee" sound of pump operation
Check points
Check that the power plug is
securely plugged into the outlet.
Check that the POWER switch is
set to the ON position.
Countermeasure
Push the power plug into
the outlet securely.
(See page 8)
Turn on the POWER switch.
(See page 8)
The chair stops in the
middle of operation.
This phenomenon is caused by the timer, but is not a problem.
Impossible to recline.
Impossible to raise and
lower the foot rest.
Check that there is no obstruction.
You feel discomfort during
the operation of reclining.
This operation is conducted for safety, but is not a problem.
Remove the obstruction.
(See page 7)
Power consumption
100 W
Rated time
30 min.
Timer
Dimensions
Weight
Upholstery
Reclining angle
Reclining method
Air pressure
Approx. 15 minutes
780 mm(30 11/16") [width] × 1,030 mm(40 9/16") [depth] × 1,230 mm(48 7/16") [height]
* When not reclined (with foot rest retracted)
780 mm(30 11/16") [width] × 1,740 mm(68 1/2") [depth] × 715 mm(28 1/8") [height]
* When reclined (with foot rest set horizontally)
Approx. 50 kg(110 lbs.)
Leather
Approx. 115 ∼ 155°
Back rest: Motor-driven type (Linked with foot rest and seat)
Foot rest: Motor-driven type (Foot rest only)
Approx. 24 ∼ 36 kPa(3.5 ∼ 5.2 PSI)
* There is a slight difference according to the part.
Do not use the chair on other than the designated voltage.
(Move toward to the opposite
direction temporarily, or do not
move smoothly.)
13
14
SANYO RELAXATION CHAIR LIMITED WARRANTY
(USA ONLY)
OBLIGATIONS
MODEL
HEC-RX1 Series
In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Factory Service
Center at the user's expense, unless specifically stated otherwise in this warranty.
If you need assistance with product operation, authorized service center referral, service assistance, problem resolution, or parts
and accessories availability; you may contact us by:
A. Visiting www.sanyoservice.com on a 24 hr/7 days a week basis or
B. calling the customer support center at 1-800-421-5013
Weekdays 7:30 AM- 5:00 PM Pacific Time
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED AND USED IN THE UNITED STATES OF AMERICA.
THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER AND DOES NOT APPLY TO PRODUCTS USED FOR ANY
INDUSTRIAL, PROFESSIONAL OR COMMERCIAL PURPOSE. THE ORIGINAL DATED BILL OF SALE OR SALES SLIP MUST BE
SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO FISHER COMPANY (SFC) warrants this SANYO
products against defects in materials and workmanship for the periods of LABOR and PARTS specified below. SFC will repair
or replace (at its option) the product and any of its parts which fail to conform to this warranty.
The warranty period commences on the date the product was first purchased at retail
LABOR
PARTS
*IN - HOME
1 YEAR
1 YEAR
1 YEAR
Note:
* In-home service is defined as product service in the consumer home or offsite if
further repairs are required.
EXCLUSIONS
This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model's
instruction manual, or (B) the repair of any product whose serial number has been altered, defaced or removed.
This warranty shall not apply to the following items: non-electrical / mechanical attachments; accessories; damage to head
cover, back pad, arm covers, seat cover, foot rest cover or pillow when not caused by defects in workmanship.
This warranty shall not apply to setup, installation, removal of the product for repair or reinstallation of the product after repair.
This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but
not limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper
maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user,
abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear.
The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any
other obligation or liability.
THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE WARRANTIES OF MERCHANTABILITY
AND FITNESS) IS LIMITED TO THE TERM OF THIS WARRANTY. IN NO EVENT SHALL SFC BE LIABLE FOR SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, OR FOR ANY DELAY
IN THE PREFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT
APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.
For your protection in the event of theft or loss of this product, please fill in the information below for your own personal
records.
Model No.
Serial No.
Date of Purchase
Purchase Price
(Located on back or bottom side of unit)
Where Purchased
Please register your relaxation chair at
www.sanyomassagechairs.com
SANYO Fisher Company
21605 Plummer Street
Chatsworth, CA 91311
www.sanyousa.com
9BF-6-P331-134AA-0 1207
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement