Specifications | Canon 0284B002 Camera Lens User Manual

Canon
EF~
LENS
EF-S60mm f/2.8 MACRO USM
Instruction
Mode d'emploi
Bedienungsanleitung
Instrucciones
Istruzioni
»
ULTRASONIC
~ffl*.~~,~~~~~*m~~o
~~m~~~~*~, ~.~*~~o
Thank you for purchasing a Canon USM lens.
The Canon EF-S60mm f/2.8 MACRO USM lens
is a macro lens that can be used for normal
photography and close-up pictures up to 1:1,
or life-size magnification. It has been
developed for use with digital SLR cameras*
compatible with EF-S lenses.
"USM" stands for Ultrasonic Motor.
Features
1. The three-group floating system results in
sharp and clear delineation at all focusing
distances from life-size to infinity.
2. A Canon macro flash (sold separately) makes
it easy to take close-up pictures with a flash.
The inner focusing mechanism enables AF
photography while the macro flash is
attached.
3. USM for fast, quiet focusing.
4. Manual focusing available in autofocusing
mode (ONE SHOT AF).
E-1
~ Safety Precautions
1. Do not look at the sun or a bright light source
through the lens or camera. Doing so could
result in loss of vision. Looking at the sun directly
through the lens is especially hazardous.
2. Whether it is attached to the camera or not, do
not leave the lens under the sun without the
lens cap attached. This is to prevent the lens
from concentrating the sun's rays, which could
cause a fire.
~ Handling Cautions
If the lens is taken from a cold environment into
a warm one, condensation may develop on the
lens surface and internal parts. To prevent
condensation in this case, first put the lens into an
airtight plastic bag before taking it from a cold to
warm environment. Then take out the lens after it
has warmed gradually. Do the same when taking the
lens from a warm environment into a cold one.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Do not make any changes or modifications to the equipment
E-2
unless otherwise specified in the instructions. If such changes or
modifications should be made, you could be required to stop
operation of the equipment.
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radiorrV technician for
help.
This digital apparatus does not exceed the Class B limits for
radio noise emissions from digital apparatus as set out in the
interference-causing equipment standard entitled "Digital
Apparatus", ICES-003 of the Industry Canada.
CE:
The C€ Mark is a Directive conformity mark of the
European Community (EC)
N118
Nomenclature
Focusing ring (-7 4)
Hood mount (-7
"..---- Distance index
Filter mounting
thread (-7 9)
Focus mode switch
(-74)
Contacts (-74)
Lens mount index (-74)
For detailed information, reference page numbers are provided in parentheses (-7 **).
E-3
Mounting and Detaching the Lens
See your camera's instructions for details on
mounting and detaching the lens.
After detaching the lens, place the lens with the
rear end up to prevent the lens surface and
electrical contacts from getting scratched.
1$ If the contacts get soiled, scratched, or have
fingerprints on them, corrosion or faulty
connections can result. The camera and lens
may not operate properly.
'*' If the contacts get soiled or have fingerprints on
them, clean them with a soft cloth.
If you remove the lens, cover it with the dust
cap. To attach it properly, align the lens mount
index and the 0 index of the dust cap as shown
in the diagram, and turn clockwise. To remove
it, reverse the order.
<$
E-4
To shoot in autofocus mode, set the focus mode
switch to AF.
To use only manual focusing, set the focus mode
switch to MF, and focus by turning the focusing
ring. The focusing ring always works, regardless
of the focus mode.
[l]AfterautofocusinginONESHOTAFmode,focus
manuaUyby pressing the shutter button halfway
and turning the focusing ring. (Full-timemanOal
focus)
,
Picture Taking
Normal Photography
The lens can be used as a medium-telephoto
lens equivalent to 96mm in 35mm format for
normal photography such as snapshots and
portraits.
Closeup Photography
Close-up photos up to 1x (life-size) magnification
are possible. The minimum focusing distance of
20cm is the distance from the subject to the film
plane. The working distance from the front of the
lens to the subject is about 9cm.
When focusing, you can give priority to framing
or to magnification.
[Framing Priority]
While looking through the viewfinder and framing
the subject, focus with the AF or MF mode.
[Magnification Priority]
1. Set the lens' focus mode switch to MF.
2. Set the magnification.
While referring to the magnification scale on
the distance index, turn the focusing ring to
the desired magnification.
3. Focus the subject.
While look:ing through the viewfinder, move the
camera forward or back to find the point of
focus.
4. Touch up the focus.
Turn the focusing ring for fine focusing.
o
~
j
Since macro shots have a very shallow. depth of
field,focuscarefullyto.obtainipropersharpness.
Image quality deteriorates near the minimum
aperture opening. due. to diffraction.
The magnification refers to the ratio between the
SUbject's size and the corresponding image size
on the image sensor plane. QnJhe distance
index,itisindicatedas1:x.
% To prevent camera shake, using a Remote
Switch. (bothsoldseparately)andtripod. is
recornrnended .
@To check the depth of field, press the camera's
depth~of~fieldpreview button.
Lj]0
E-5
About Exposure
Setting the Exposure
When taking photographs using TTL
metering, no exposure compensation is
necessary to meter the light coming through
the lens.
With TTL metering, AE (autoexposure) is
possible at all focusing distances. Just set the
desired picture-taking mode, then check the
shutter speed and aperture before taking the
picture.
Magnification and Effective f-number
The aperture displayed by the camera assumes
that the focus is set to infinity. The actual aperture
(effective f-number) becomes darker (effective fnumber increases) at closer focusing distances
(magnification increases). This does not cause
exposure problems for normal picture-taking.
However, for closeup photography, you cannot
ignore the change in the effective f-number.
When you use a handheld exposure meter to
set the exposure, you must take into account
the exposure factor shown in the following
table.
E-6
Magnification
1 : 5 1: 4 1 : 3 1 : 2 1:1.5 1: 1
Effective fiNo.
3.50 3.66 3.89 4.39 4.86 5.84
1
Exposure Factor\in + stops +"2
2
(stops)
lin stops +3
+
1
+"2
2
+3
+1
+1
+1
+1
+1+ +2
++1t
+2
Macro Flash (Sold Separately)
The Canon Macro Ring Lite MR-14EX or the
Macro Twin Lite MT-24EX enables fully
automatic macro flash photography up to 1x
magnification in E-TTL autoflash mode.
r:¥I
LjJ
Hood (Sold Separately)
The ET-67B hood can keep unwanted light out of
the lens, and also protects the lens from rain,
snow, and dust.
For information on operating the Canon Macro
Ring Lite MR-14EXor the Macro Twin Lite MT24EX, refer to the individual instruction booklets.
} Using aperture-priority AE (Av) or Manual (M) is
recommended.
#
Flash Range (IS0100)
MR-14EX
MT-24EX
Flash Head Angle
Settings for MT-24EX
Inward Angle
f FI,....-aSh--,H.---ead--j
Magnification t--o_
1 :1-1: 1.5
1:2
1:3
1:5
•
•
••
•
To attach the hood, align the hood with the lens
hood mount, then turn the hood clockwise to
secure it.
The hood can be reverse-mounted on the lens
for storage.
Part of the picture may be blocked if the hood is
notattached properly.
@l When attaching or detaching the hood, grasp
the base of the hood to tu rn it. To prevent
deformation, do not grasp the rim of the hood to
turn it.
E-7
Infinity Distance Mark
1:~
4
1
3
3
lJ
.
1-00
ft
Attaching a 2500, 500, or 5000 (52mm) Closeup Lens enables close-up photography.
The magnification will be as follows:
m
_\T7~",
__
To compensate for shifting of the infinity focus
point that results from changes in temperature.
The infinity position at normal temperature is the
point at which the vertical line of the L mark is
aligned with the distance indicator on the
distance scale.
o •Ror~ccurate ma.nual focusing on)subjectsat
infinity distance, look through the viewfinder while
rotatIng the focusing ring.
E-8
Close-up Lenses (Sold separately)
2500
500/5000
Near
Far
1.33x
O.25x
O.18x
O.12x
Sales of the 500 Close-up Lens may already
be terminated in some areas.
When using a Close-up Lens, focus manually.
Filters (Sold Separately)
You can attach filters to the filter mounting
thread on the front of the lens.
0 ..
Uptotwo 52mmifilters can be attached.
This lens can accommodate both filters and the
rnacroflashat theisametime.
If you need a polarizing filter, use Canon's PL-G
52mmpolarizing filter.
(i) To adjust the polarizing filter, first remove the
lens hood.
bWhanthe Canon's PL-G 52mm polarizing filter
is attached, the lens cap cannot be attached.
Extension Tubes (Sold Separately)
You can attach Extension Tube EF12 II or EF25
II for magnified shots. The shooting distance and
magnification are shown below.
@
@
I EF12 II
I EF25 II
Camera-to-Subject
Distance (mm)
Near
Far
207
445
215
289
Magnification
Near
1.28x
1.61x
I
I
I
Far
0.20x
0.44x
Extension· Tube EF12 or EF25 cannot be
attached.
bWhen an Extension Tube is attached,focus
manually.
Gelatin Filter Holder (Sold separately)
With the Gelatin Filter Holder, you can use filters
to create various effects.
The Gelatin Filter Holder compatibility is shown
below.
Gelatin Filter Holder III: Up to six hoods can be
used.
Gelatin Filter Holder IV: Up to six hoods can
be used.
E-9
Specifications
Image Size
Focal Length/Aperture
Lens Construction
Minimum Aperture
Angle of View
Min. Focusing Distance
Max. Magnification
Field of View
Filter Diameter
Max. Diameter and Length
Weight
Hood
Lens Cap
Case
15.1 x 22.7 mm
60 mm f/2.8
8 groups, 12 elements
f/32
Vertical: 14° 10'
Diagonal: 24° 30'
0.2 m/0.7 ft.
1x
15.1 x 22.7 mm/0.6 x 0.9 inch
52 mm/2.0 inch
73 x 69.8 mm/2.9 x 2.7 inch
335 g/11.8 oz
ET-678 (Sold separately)
E-52U
LP1 016 (Sold separately)
Horizontal: 20° 40'
Equivalent to 96 mm in the 35mm film format.
The lens length is measured from the mount surface to the front end of the lens. Add 17 mm when including
the lens cap and dust cap.
The size and weight listed are for the lens only, except as indicated.
Aperture settings are specified on the camera.
The EF1.4X II/EF2X II extenders cannot be used with this lens.
All data listed is measured according to Canon standards.
Product specifications and appearance are subject to change without notice.
E-10
Canon
~i'.1 /~it~tl http://canon.jp/
~i'.1 /ft&7C~it~tl T 108-801 1 *~~~[z:~~2- 16-6
CANON INC.
30-2,Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
U.S.A.
CANON U.S.A. INC.
For all inquiries concerning this lens, call toll free in the U.S.
1-800-0K-CANON or write to: Customer Relations, Canon U.S.A., Inc.
One Canon Plaza, Lake Success, N.Y. 11042-1198
CANADA
CANON CANADA INC. HEADQUARTERS
6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada
CANON CANADA INC. MONTREAL BRANCH
5990, Cote-de-Liesse, Montreal Quebec H4T 1V7, Canada
CANON CANADA INC. CALGARY OFFICE
2828, 16th Street,N.E. Calgary, Alberta T2E 7K7, Canada
For all inquiries concerning this lens, call toll free in Canada
1-800-0K-CANON
EUROPE, AFRICA & MIDDLE EAST
CANON EUROPA N.V.
Bovenkerkerweg 59-61, P.O. Box 2262,1180 EG Amstelveen, The Netherlands
CANON COMMUNICATION & IMAGE FRANCE S.A.
102, Avenue du General de Gaulle 92257 La Garenne-Colombes Cedex France
CANON UK LTD.
'
Woodhatch Reigate Surrey RH2 8BF, United Kingdom
CANON DEUTSCHLAND GmbH
Europark Fichtenhain A10, 47807 Krefeld, Germany
CANON ITALIA S.p.A.
Via Milano 8 1-20097 San Donato Milanese (MI) Italy
CANON Schweiz AG
Geschaftsbereich Wiederverkauf, Industriestrasse 12 CH-8305
Dietlikon, Switzerland
'
CT1-7556-000
CANON G. m. b. H.
Oberlaaerstrasse 233, 4th floor, 1100 Wien, Austria
CANON Espana, S.A.
C/Joaqufn Costa, 41, 28002 Madrid, Spain
SEQUE Soc. Nac. de Equip., Lda.,
Prac;a da Alegria, 58,2°, 1269-149 Lisboa, Portugal
CENTRAL & SOUTH AMERICA
CANON LATIN AMERICA, INC. DEPTO DE VENTAS
703 Waterford Way Suite 400 Miami, FL 33126 U.S.A.
CANON LATIN AMERICA, INC. CENTRO DE SERVICIO Y
REPARACION
Apartado 2019, Zona Libre de Colon, RepUblica de Panama
ASIA
CANON CHINA CO. LTD.
b~~~~~~gTg~~~~r~~7~:erryCentre,
1 Guang Hua Road,
CANON HONGKONG CO., LTD.
~~~~i J~~gMetroPolis Tower, 10 Metropolis Drive, Hunghom, Kowloon,
CANON SINGAPORE PTE. LTD.
1 HarbourFront Avenue #04-01 Keppel Bay Tower Singapore 098632
OCEANIA
CANON AUSTRALIA PTY. LTD.
1 Thomas Holt Drive, North Ryde, N.S.W. 2113, Australia
CANON NEW ZEALAND LTD.
Akoranga Business Park, Akoranga Drive, Northcote, Auckland, New Zealand
JAPAN
CANON SALES CO., INC.
16-6, Kohnan 2-chome, Minato-ku, Tokyo 108-8011, Japan
© CANON INC. 2005
2005.4.1
PRINTED IN TAIWAN
I">~~R"'"
"--'~I.V I I
Dealer Record of Canon Purchase
Fiche d'Achat pour Concessionnaire Canon
PRESENT OWNERSHIP AND PRODUCTS INTERESTED IN
Articles deja en possession ou juges dignes d'interet
CAMERAS
APPAREILS
-PHOTO
.
OWNS
INTERESTED IN
En possession Interesse par
_
(Camera)
(Appareil)
(Camera)
(Appareil)
INTERCHANGEABLE LENS
Objectif interchangeable
(Lens)
(Objectif)
(Lens)
(Objectif)
OWNS
INTERESTED IN
En possession Interesse par
MODEL
Modele
CUSTOMER
Client
NAME
ADDRESS
Nom - - - - - " " - - - - - - - - - Adresse
CITY/STATE
ZIP
PHONE
Ville/Province - - - - - - - - - - - - - - - - Code postal -------Telephone - - - - - - -
NAME
NOM
ADDRESS
ADRESSE
CITY
VILLE
POSTAL CODE
CODE POSTAL
PROVINCE
THIS WARRANTY CARD AND YOUR BILL OF SALE MUST BE
PRESENTED FOR WARRANTY SERVICE.
CETTE CARTE DE GARANTIE ET VOTRE PREUVE D'ACHAT
DOIVENT ETRE PRESENTES POUR RECEVOIR LE SERVICE
SOUS GARANTIE.
DEALER'S NAME & ADDRESS
MARCHAND NOM & ADRESSE
BODY NO.
BOITIERNO
PURCHASE DATE
DATE D'ACHAT
/
/
DO NOT MAIL, KEEP THIS WARRANTY CARD. IT IS YOUR PERMANENT RECORD OF WARRANTY. IF LOST IT WILL NOT BE RE-ISSUED.
VEUILLEZ NE PAS POSTER. CONSERVEZ CEnE CARTE DE GARANTIE. ELLE CONSTITUE VOTRE PREUVE PERMANENTE DE GARANTIE. SI LA CARTE EST PERDUE, ELLE NE SERA PAS RENOUVELEE.
CT5-1544-000
Canon
LIMITED WARRANTY
The Limited Warranty set forth below is given by Canon U.S.A., Inc. in the United States and Canon Canada, Inc. in Canada (herein referred to collectively as "Canon") with respect to the
Canon Binoculars and Photographic Lens Products packaged with this Limited Warranty and identified by model number on this Limited Warranty Card (each a "Producf') when purchased and
used in the United States or Canada.
This Limited Warranty is only effective upon presentation of this warranty card and proof of purchase.
A Product, when delivered to you in new condition in its original container, is warranted against defects in materials or workmanship as follows: for a period of one (1) year from the date of
original purchase, defective parts or a defective Product returned to Canon or its authorized service providers, and proven to be defective upon inspection, will be repaired with new or
comparable rebuilt parts or exchanged for a refurbished Product, as determined by Canon or the authorized service provider, in their sole discretion. Replaced parts and exchanged Products
will become the property of Canon.
When returning a Product for warranty service, the shipping charges must be prepaid and the Product should be shipped in its original container, or an equivalent, properly packed to withstand
the hazards of shipment and be fully insured. A copy of this warranty card and proof of purchase should be enclosed, as wel~as a description of the problem (including film samples, where
appropriate). Repairs will be made and the Product will be returned, shipped at NO CHARGE, within the country of repair.
This warranty only covers defective materials or workmanship encountered in normal use and service of a Product and does not apply in the following cases:
Loss or damage due to neglect and/or abuse causing deterioration, mishandling, accident or failure to follow operating instructions.
If a Product is defective as a result of leaking batteries or damage due to water or other liquid.
Defective materials or workmanship where the defect is due to a Product having been serviced or modified by other than Canon or a Canon authorized service provider.
Malfunction resulting from the use of accessories, attachments, supplies, parts or devices (including, without limitation, batteries, film, flash attachments and other accessories) that do not
conform to Canon specifications.
(e) Damage resulting during shipment. (Claim must be presented and examined by the shipper).
(f) Damage or service resulting from modifications or alterations to a Product in any way (inclUding any alteration or removal of its serial number or identification marks).
(a)
(b)
(c)
(d)
NO IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, APPLIES TO A PRODUCT AFTER THE
APPLICABLE PERIOD OF THE EXPRESS LIMITED WARRANTY STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY, EXCEPT AS MENTIONED ABOVE, GIVEN
BY ANY PERSON OR ENTITY WITH RESPECT TO A PRODUCT SHALL BIND CANON (SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU). CANON SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, INCONVENIENCE, EXPENSE
FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
(INCLUDING, WITHOUT LIMITATION, ANY LOSS OF FILM) CAUSED BY THE USE OR MISUSE OF, OR INABILITY TO USE, A PRODUCT, REGARDLESS OF THE LEGAL THEORY ON
WHICH THE CLAIM·IS BASED, AND EVEN IF CANON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL RECOVERY OF ANY KIND AGAINST
CANON BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY CANON AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE
FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF
USE OR MISUSE OF, OR INABILITY TO USE, THE PRODUCT NOT CAUSED SOLELY AND DIRECTLY BY THE NEGLIGENCE OF CANON (SOME STATES AND PROVINCES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU). THIS
LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF A PRODUCT, OR THE PERSON FOR WHOM IT WAS PURCHASED AS A
GIFT. AND STATES YOUR EXCLUSIVE REMEDY.
Canon U.S.A., Inc., One Canon Plaza, Lake Success, NY 11042-1198
Canon Canada, Inc., 6390 Dixie Road, Mississauga, Ontario L5T 1P7
~
~~~
•••••
~
...
,f.,
;
"
"
"
•
>'
'-'.'
~,
'"
.x'
J: ~"'< ' ",~v,,",",
v,
"-,' " d v, 'xd
Canon USA
One Canon Plaza, Lake Success, N.Y. 11042-1198
Tel: (1 )-800-828-4040
~,: J~':"
.. "
>
"
,
...
~
',"" '
v',
x
",~ ',,> \g<,:~L'd:;;:;<~:J;~.';{x:(~'":~'f8':f:~t;;~,>to,~;t;;3~:."' :.h ><:~,:~
':
Canon Canada
6390 Dixie Road, Mississauga, Ontario L5T 1P7
Tel: (1 )-800-828-4040
'v:,
Download PDF