User guide | Canon 107 Camcorder User Manual

Camera User Guide
• Make sure you read this guide before using the camera.
• Store this guide safely so that you can use it in the future.
ENGLISH
Checking the Package Contents
Check if the following items are included in your camera package. If anything
is missing, contact the retailer from which you purchased the camera.
Camera
Interface Cable
IFC-400PCU
Getting Started
Battery Pack NB-4L
(with Terminal Cover)
AV Cable
AVC-DC400
DIGITAL CAMERA
Solution Disk
Battery Charger
CB-2LV/CB-2LVE
Wrist Strap
WS-DC7
Warranty System
Booklet
Using the Manuals
Also refer to the manuals on the DIGITAL CAMERA Manuals Disk.
• Camera User Guide (This Guide)
Once you have mastered the basics, use the camera’s
many features to shoot more challenging photos.
• Personal Printing Guide
Read when you want to connect the camera to a printer
(sold separately) and print.
• Software Guide
Read when you want to use the included software.
• A memory card is not included.
• Adobe Reader is required to view the PDF manuals. Microsoft Word/
Word Viewer can be installed to view the Word manuals (required only
for manuals for the Middle East).
2
Read This First
Test Shots
Take some initial test shots and play them back to make sure the images
were recorded correctly. Please note that Canon Inc., its subsidiaries and
affiliates, and its distributors are not liable for any consequential damages
arising from any malfunction of a camera or accessory, including memory
cards, that results in the failure of an image to be recorded or to be recorded
in a way that is machine readable.
Warning Against Copyright Infringement
The images recorded with this camera are intended for personal use. Do not
record images that infringe upon copyright laws without the prior permission
of the copyright holder. Please be advised that in certain cases the copying
of images from performances, exhibitions, or commercial properties by
means of a camera or other device may contravene copyright or other legal
rights even if the image was shot for personal use.
Warranty Limitations
For information on your camera's warranty, please refer to the Canon
Warranty System Booklet supplied with your camera.
For Canon Customer Support contacts, please see the Warranty System
Booklet.
LCD Monitor
• The LCD monitor is produced with extremely high-precision manufacturing
techniques. More than 99.99% of the pixels operate to specification, but
occasionally non-performing pixels may appear as bright or dark dots. This
is not a malfunction and has no effect on the recorded image.
• The LCD monitor may be covered with a thin plastic film for protection
against scratches during shipment. If so, remove the film before using the
camera.
Camera Body Temperature
Please take care when operating the camera for an extended period as the
camera body may become warm. This is not a malfunction.
Memory Cards
The various types of memory cards that can be used in this camera are
collectively referred to as memory cards in this guide.
3
What Do You Want to Do?
4
Shoot
● Shoot, leaving it to the camera to make settings . . . . . . . . . . . . 24
● Shoot to match special conditions. . . . . . . . . . . . . . . . . . . . 56 – 58
Take good people shots
I
Portraits
(p. 56)
F
At night
(p. 56)
V
Kids and pets
(p. 56)
Take good landscapes
U
H
Indoors
(p. 57)
t
Fireworks
(p. 57)
P
Against snow
(p. 58)
O
Sunsets
(p. 57)
Shoot various other scenes
w
At the beach
(p. 57)
Foliage
(p. 58)
S
Underwater
(p. 57)
y
Aquarium
(p. 58)
Z
Low light
(p. 58)
● Focus on faces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24, 64, 80
● Shoot in places where I cannot use the flash (turn off the flash) 59
● Take pictures with me in them too (self-timer) . . . . . . . . . . . 63, 64
● Insert the date and time into my shots . . . . . . . . . . . . . . . . . . . . 62
● Take close-up pictures of subjects (macro shooting) . . . . . . . . . 67
● Take close-up pictures of subjects using the zoom
(digital macro shooting). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
● Take sepia toned or black and white pictures . . . . . . . . . . . . . . . 74
● Change the size of picture I want to take (recording pixels) . . . . 69
● Take pictures continuously . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
● Shoot without the effects of camera shake (image stabilization) 138
● Shoot without the effects of camera shake even in low light
conditions (High ISO Auto) . . . . . . . . . . . . . . . . . . . . . . . . . . 58, 71
● Maintain the focus on moving subjects (Servo AF). . . . . . . . . . . 83
● Make dark subjects appear brighter (i-Contrast). . . . . . . . . . . . . 87
4
What Do You Want to Do?
View
1
● Look at my pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
● Automatically play back pictures (slideshow) . . . . . . . . . . . . . . 107
● Look at my pictures on a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
● Quickly search pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . 104, 106
● Erase pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 115
● Protect pictures from accidental erasure. . . . . . . . . . . . . . . . . . 113
Shoot/View Movies
E
2
● Shoot movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
● View movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Print
● Easily print pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Save
● Save images to a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Other
3
● Turn off sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
● Use the camera abroad. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 135
5
Table of Contents
Chapters 1 – 3 explain the basic operations and frequently used functions of
this camera. Chapters 4 onward explain the advanced functions, letting you
learn more as you read each chapter.
Checking the Package Contents .......2
Read This First ..................................3
What Do You Want to Do? ................4
Conventions Used in this Guide ........8
Safety Precautions.............................9
1 Getting Started ....................13
Charging the Battery........................14
Inserting the Battery and
Memory Card .............................16
Setting the Date and Time ...............19
Setting the Display Language..........21
Formatting Memory Cards ...............22
Pressing the Shutter Button.............23
Taking Pictures ................................24
Viewing Images ...............................27
Erasing Images................................28
Printing Images................................29
Shooting Movies ..............................31
Viewing Movies................................33
Transferring Images to a Computer.34
Accessories .....................................38
Separately Sold Accessories ...........40
2 Learning More......................41
Components Guide..........................42
Information Displayed
on the Screen.............................44
Indicator ...........................................46
FUNC. Menu – Basic Operations ....47
MENU – Basic Operations...............48
Changing the Sound Settings ..........49
Changing the Screen Brightness .....50
6
Returning the Camera
to Default Settings ..................... 51
Low Level
Memory Card Formatting .......... 52
Power Saving Function
(Auto Power Down) ................... 53
Clock Functions............................... 54
3 Shooting in Special
Conditions and Commonly
Used Functions................... 55
Shooting in Various Conditions ....... 56
Turning the Flash Off ...................... 59
Zooming in More Closely on Subjects
(Digital Zoom)............................ 60
Inserting the Date and Time............ 62
Using the Self-Timer ....................... 63
Using the Face Self-Timer .............. 64
4 Choosing Settings Yourself
.............................................. 65
Shooting in Program AE.................. 66
Adjusting the Brightness
(Exposure Compensation)......... 66
Turning the Flash On ...................... 67
Shooting Close-ups (Macro) ........... 67
Shooting Far Away Subjects
(Infinity)...................................... 68
Zooming In on Close Subjects
(Digital Macro) ........................... 68
Changing the Recording Pixels....... 69
Changing the Compression Ratio
(Image Quality).......................... 69
Changing the ISO Speed ................ 71
Adjusting the White Balance ........... 72
Table of Contents
Continuous Shooting....................... 73
Changing the Tone of an Image
(My Colors) ............................... 74
Shooting Using the Two Second
Self-Timer ................................. 75
Customizing the Self-Timer............. 76
Shooting Using a TV Monitor .......... 77
Changing the Composition
with the Focus Lock .................. 77
5 Getting More Out of
Your Camera ....................... 79
Changing the AF Frame Mode........ 80
Magnifying the Focal Point.............. 81
Shooting with the AF Lock .............. 82
Shooting with Servo AF .................. 83
Changing the Metering Mode.......... 84
Shooting with the AE Lock .............. 85
Shooting with the FE Lock .............. 85
Shooting with Slow Synchro ........... 86
Correcting the Brightness and
Shooting (i-Contrast).................... 87
Red-Eye Correction ........................ 88
Checking for Shut Eyes .................. 89
Shooting Long Exposures............... 90
Changing the Color and Shooting... 91
Shooting Stitch Assist Images ........ 94
6 Using Various Functions for
Shooting Movies................. 95
Changing the Movie Mode .............. 96
Changing the Image Quality ........... 97
AE Lock/Exposure Shift .................. 98
Other Shooting Functions ............... 99
Playback Functions....................... 100
Editing ........................................... 101
7 Using Playback and Other
Functions........................... 103
Quickly Searching Images............. 104
Viewing Images
in Filtered Playback ................. 106
Viewing Slideshows....................... 107
Checking the Focus....................... 109
Magnifying Images ........................ 110
Changing Image Transitions ......... 110
Viewing Images on a TV ............... 111
Viewing Images
on a High-Definition TV ........... 112
Protecting Images ......................... 113
Erasing All Images ........................ 115
Organizing Images by Category
(My Category).......................... 118
Rotating Images ............................ 120
Resizing Images............................ 121
Trimming ....................................... 122
Adding Effects
with the My Colors Function .... 123
Correcting the Brightness
(i-Contrast)............................... 124
Correcting the Red-Eye Effect....... 125
Printing from the Print List
(DPOF) .................................... 126
Choosing Images for Printing
(DPOF) .................................... 128
8 Customizing the Camera.. 131
Changing Functions ...................... 132
Changing Shooting Functions ....... 136
Changing Playback Functions....... 139
Changing the Start-up Image
or Sound .................................. 139
7
Table of Contents
9 Useful Information.............141
Using Household Power ................142
Troubleshooting .............................143
List of Messages that Appear
on the Screen...........................146
Functions Available
in Each Shooting Mode............148
Menus ........................................... 150
Handling Precautions .................... 154
Specifications ................................ 155
Index ............................................. 158
Conventions Used in this Guide
• Icons are used in the text to represent the camera buttons and switches.
• Language that displays on the screen appears inside [ ] (square brackets).
• The directional buttons and FUNC./SET button are represented by the
following icons.
(Up button)
(FUNC./SET button)
(Right button)
(Left button)
(Down button)
•
: Troubleshooting tips.
•
: Hints for getting more out of your camera.
•
: Things you should be careful about.
•
: Supplemental information.
• (p. xx): Reference pages. “xx” stands for page number.
• This guide assumes all functions are at their default settings.
8
Safety Precautions
• Before using the camera, please ensure that you read the safety precautions described
below. Always ensure that the camera is operated correctly.
• The safety precautions noted on the following pages are intended to prevent injuries to
yourself and other persons, or damage to the equipment.
• Be sure to also check the guides included with any separately sold accessories you use.
Warning Denotes the possibility of serious injury or death.
Caution
Denotes the possibility of injury.
Caution
Denotes the possibility of damage to the equipment.
Warning
Camera
• Do not trigger the flash in close proximity to human eyes.
Exposure to the intense light produced by the flash could damage eyesight. In
particular, remain at least one meter (39 inches) away from infants when using the flash.
• Store this equipment out of the reach of children and infants.
Strap: Putting the strap around a child’s neck could result in asphyxiation.
Memory card: Dangerous if accidentally swallowed. If this occurs, contact a doctor
immediately.
• Do not attempt to disassemble or alter any part of the equipment that is not
expressly described in this guide.
• To avoid the risk of injury, do not touch the interior of the camera if it has been
dropped or otherwise damaged.
• Stop operating the camera immediately if it emits smoke, a strange smell, or
otherwise behaves abnormally.
• Do not use organic solvents such as alcohol, benzine, or thinner to clean the
equipment.
• Do not allow liquids or foreign objects to enter the camera.
This could result in fire or electrical shock.
If liquid or foreign objects come into contact with the camera interior, immediately turn
the camera power off and remove the battery.
• Use only recommended power sources.
Using other power sources could result in fire or electrical shock.
Battery, Battery Charger
• Use only recommended batteries.
• Do not place the battery near or in direct flame.
• Do not let the battery come into contact with water (e.g. sea water) or other liquids.
• Do not attempt to disassemble, alter or apply heat to the battery.
9
Safety Precautions
• Avoid dropping or subjecting the battery to severe impacts.
This may cause explosions or leaks, resulting in fire, injury and damage to the
surroundings. In the event that a battery leaks and the eyes, mouth, skin or clothing
contacts these substances, immediately flush with water and seek medical assistance.
If the battery charger becomes wet, unplug it from the outlet and consult your camera
distributor or the closest Canon Customer Support Help Desk.
• Use only the specified battery charger to charge the battery.
• Do not cut, damage, alter or place heavy items on the power cord.
• Unplug the power cord periodically and wipe away any dust and dirt that has
collected on the plug, the exterior of the power outlet, and the surrounding area.
• Do not handle the power cord with wet hands.
This could result in fire or electrical shock.
Other Warnings
• Do not play the supplied CD-ROM(s) in any CD player that does not support
data CD-ROMs.
Playing the CD-ROM(s) in an audio CD player (music player) could damage the
speakers. It is also possible to suffer hearing loss from listening with headphones to
the loud sounds of a CD-ROM played on a music CD player.
Caution
• Be careful not to bang the camera or subject it to strong impacts or shocks
when hanging it by the strap.
• Be careful not to bump or push strongly on the lens.
This could damage the camera or lead to injury.
• Do not use the equipment in a manner that exceeds the rated capacity of the
electrical outlet or wiring accessories. Do not use if the power cord or plug are
damaged, or not fully plugged into the outlet.
This could result in electrical shock or fire.
• Avoid using, placing or storing the camera in the following places.
- Places subject to strong sunlight.
- Places subject to temperatures above 40 °C (104 °F).
- Humid or dusty areas.
These could cause leakage, overheating or an explosion of the battery, resulting in
electrical shock, fire, burns or other injuries. High temperatures may also cause
deformation of the casing.
• Do not allow dirt or metal objects (such as pins or keys) to contact the charger
terminals or plug.
This could result in fire, electrical shock or other damage.
• The slideshow transition effects may cause discomfort when viewed for
prolonged periods.
10
Safety Precautions
• Do not use the flash with dirt, dust or other items stuck to the surface, or if it is
covered by your fingers or clothing.
This could result in burns or damage to the flash.
Caution
• Do not aim the camera at bright light sources (the sun, etc.).
Doing so may cause malfunctions or damage the image sensor.
• When using the camera on a beach or at a windy location, be careful not to
allow dust or sand to enter the camera.
This may cause the camera to malfunction.
• In regular use, small amounts of smoke may be emitted from the flash.
This is due to the high intensity of the flash burning dust and foreign materials stuck to
the front of the unit. Please use a cotton swab to remove dirt, dust or other foreign
matter from the flash to prevent heat build-up and damage to the unit.
• Unplug the battery charger from the power outlet after recharging is complete,
or when you are not using it.
• Do not place anything, such as cloth on top of the battery charger while it is
charging.
Leaving the unit plugged in for a long period of time may cause it to overheat and
distort, resulting in fire.
• Remove and store the battery when you are not using the camera.
If the battery is left inside the camera, damage caused by leakage may occur.
• Before you discard batteries, cover the terminals with tape or other insulators.
Contacting other metal materials in waste containers may lead to fire or explosions.
• Do not place the battery near pets.
Pets biting the battery could cause leakage, overheating or explosion, resulting in fire
or injuries.
• Do not sit in a chair with the camera in your pocket.
Doing so may cause malfunctions or damage the LCD monitor.
• When putting the camera in your bag, ensure that hard objects do not come into
contact with the LCD monitor.
• Do not attach accessories to the strap.
Doing so may cause malfunctions or damage the LCD monitor.
11
12
1
Getting Started
This chapter explains preparations before shooting, how to shoot in
A mode, and then how to view, erase and print the images you
take. The latter part of this chapter explains how to shoot and view
movies and transfer images to a computer.
Attaching the Strap/Holding the Camera
• Attach the included strap and place it around your wrist to avoid dropping
the camera during use.
• Keep your arms tight against your body while holding the camera firmly by
the sides. Be sure that your fingers do not block the flash.
Strap
13
Charging the Battery
Use the included charger to charge the battery. Be sure to charge the battery
as it is not charged at the time of purchase.
Remove the cover.
Insert the battery.
● Align the S marks on the battery and
charger, then insert the battery by sliding it
in
and down
.
Charge the battery.
● For CB-2LV: Flip out the plug
CB-2LV
CB-2LVE
and plug
the charger into a power outlet
.
● For CB-2LVE: Plug the power cord into
the charger, then plug the other end into a
power outlet.
X The charge lamp lights red and charging
starts.
● The charge lamp will light green when
charging has finished. Charging takes
approx. 1 hour and 30 minutes.
Remove the battery.
● Unplug the battery charger from the power
outlet, then remove the battery by sliding it
in
and up
.
To protect the battery and prolong its life, do not charge it for longer than
24 hours continuously.
14
Charging the Battery
Approximate Number of Shots That Can Be Taken
Number of shots
220
6
Playback Time (Hours)
• The number of shots that can be taken is based on the Camera & Imaging Products
Association (CIPA) measurement standard.
• Under some shooting conditions, the number of shots that can be taken may be less
than mentioned above.
Battery Charge Indicator
An icon or message will appear on the screen indicating the battery’s charge state.
Display
Summary
Good.
Slightly depleted, but sufficient.
(Blinking red) Nearly depleted.
“Change the battery pack.”
Depleted. Recharge the battery.
Using the battery and charger effectively
• Charge the battery on the day, or the day before, it will be used.
Charged batteries continue to discharge naturally even if they are not used.
Attach the cover to a charged battery
so that the S mark is visible.
• How to store the battery for long periods.
Deplete and remove the battery from the camera. Attach the terminal cover and
store the battery. Storing a battery for long periods of time (about a year) without
depleting it may shorten its life span or affect its performance.
• The battery charger can also be used when abroad.
The charger can be used in regions that have 100 – 240 V (50/60 Hz) AC power.
If the plug does not fit the outlet, use a commercially available plug adapter. Do
not use electrical transformers for foreign travel as they will cause damage.
• The battery may develop a bulge.
This is a normal characteristic of the battery and does not indicate a problem.
However, if the battery bulges to the point where it will no longer fit into the
camera, please contact a Canon Customer Support Help Desk.
• If the battery is quickly depleted even after charging, it has reached the
end of its life span.
Purchase a new battery.
15
Inserting the Battery and Memory Card
Insert the included battery and a memory card into the camera.
Check the card’s write-protect tab.
● If the memory card has a write-protect tab,
you will not be able to record images if the
tab is in the locked position. Slide the tab
up until you hear a click.
Open the cover.
● Slide the cover
, and open it
.
Insert the battery.
● Insert the battery as shown until it locks
into place with a click.
● Be sure to insert the battery in the correct
direction or it will not properly lock into
place.
Terminals
Insert the memory card.
● Insert the memory card as shown until it
locks into place with a click.
● Be sure the memory card is oriented
correctly. Inserting the memory card in the
wrong direction could damage the
camera.
Terminals
Close the cover.
● Close the cover
, and slide it
locks into place with a click.
16
until it
Inserting the Battery and Memory Card
Removing the Battery and Memory Card
Remove the battery.
● Open the cover and press the battery lock
in the direction of the arrow.
X The battery will pop up.
Remove the memory card.
● Push the memory card in until you hear a
click, then slowly release it.
X The memory card will pop up.
17
Inserting the Battery and Memory Card
Approximate Number of Shots per Memory Card
Memory Card
Number of shots
2 GB
626
8 GB
2505
• Values are based on the default settings.
• The number of shots that can be taken will vary depending on camera settings, the
subject and the memory card used.
Can you check the number of shots that can be taken?
You can check the number of shots that can be taken when the camera is in a
Shooting mode (p. 24).
Number of shots that can be taken
Compatible Memory Cards
•
•
•
•
•
SD memory cards
SDHC memory cards
MultiMediaCards
MMCplus memory cards
HC MMCplus memory cards
What is the write-protect tab?
SD and SDHC memory cards have a write-protect tab. If this tab is in the locked
position, [Card locked!] will appear on the screen and you will not be able to take
or erase images.
18
Setting the Date and Time
The Date/Time settings screen will appear the first time the camera is turned
on. Since the dates and times recorded into your images are based on these
settings, be sure to set them.
Turn on the camera.
● Press the ON/OFF button.
X The Date/Time screen will appear.
Set the date and time.
● Press the qr buttons to choose an
option.
● Press the op buttons to set a value.
Make the setting.
● Press the m button.
X Once the date and time have been set,
the Date/Time screen will close.
● Pressing the ON/OFF button will turn off
the camera.
Reappearing Date/Time screen
Set the correct date and time. If you have not set the date and time, the Date/
Time screen will appear each time you turn on the camera.
Daylight saving time settings
If you choose
in Step 2 and press the op buttons to choose
the time to daylight saving (1 hour ahead).
, you will set
19
Setting the Date and Time
Changing the Date and Time
You can change the current date and time settings.
Display the menus.
● Press the n button.
Choose [Date/Time] in the 3 tab.
● Press the qr buttons to choose the 3
tab.
● Press the op buttons to choose [Date/
Time], then press the m button.
Change the date and time.
● Follow Steps 2 and 3 on p. 19 to adjust
the setting.
● To close the menus, press the n
button.
Date/Time battery
• The camera has a built-in date/time battery (backup battery) that allows the
date/time settings to be retained for about three weeks after the battery pack
has been removed.
• By inserting a charged battery or connecting an AC adapter kit (sold separately,
p. 40) the date/time battery can be charged in about 4 hours even if the camera
is not turned on.
• If the date/time battery is depleted, the Date/Time menu will appear when you
turn the camera on. Follow the steps on p. 19 to set the date and time.
20
Setting the Display Language
You can change the display language in the LCD monitor menus and
messages.
Enter Playback mode.
● Press the 1 button.
Display the settings screen.
● Press and hold the m button
, then
immediately press the n button
.
Set the display language.
● Press the opqr buttons to choose a
language, then press the m button.
X Once the display language has been set,
the settings screen will close.
What if the clock appears when the m button is pressed?
The clock will appear if too much time passes between pressing the m button
and the n button in Step 2. If the clock appears, press the m button to
remove the clock and repeat Step 2.
You can also change the display language by pressing the n button,
choosing the 3 tab, and choosing the [Language] menu item.
21
Formatting Memory Cards
Before you use a new memory card or one that has been used in other
devices, you should format the card with this camera. Formatting (initializing)
a memory card erases all data on the memory card. As you cannot retrieve
the erased data, exercise adequate caution before formatting the memory
card.
Display the menu.
● Press the n button.
Choose [Format].
● Press the qr buttons to choose the 3
tab.
● Press the op buttons to choose
[Format], then press the m button.
Format the memory card.
● Press the qr buttons to choose [OK],
then press the m button.
X The memory card will be formatted.
X When formatting has finished, the menu
screen will reappear.
• Formatting or erasing data on a memory card merely changes the file
management information on the card and does not ensure its contents
are completely erased. Be careful when transferring or disposing of a
memory card. When disposing of a memory card, take precautions such
as physically destroying the card to prevent personal information leaks.
• The total capacity of the memory card displayed in the formatting screen
may be less than indicated on the memory card.
22
Pressing the Shutter Button
The shutter button has two stops. To take images that are in focus, be sure
to first press the shutter button lightly (halfway) to focus, then take the shot.
Press halfway (lightly to the first
stop).
X The camera automatically focuses and
selects the necessary settings for
shooting, such as the brightness.
X When the camera focuses, it will beep
twice and the indicator will light green.
Press fully (to the second stop).
X The camera plays the shutter sound and
takes the shot.
● Since the shot is being taken while the
shutter sound plays, be careful not to
move the camera.
Does the length of the shutter sound change?
• Since the time required to shoot differs according to the scene you want to take,
the length of the shutter sound may change.
• If the camera or subject moves while the shutter sound is playing, the recorded
image may be blurry.
If you just press the shutter button fully without pausing halfway, the
image may not be in focus.
23
Taking Pictures
Since the camera can determine the subject and shooting conditions, you
can let it automatically select the best settings for the scene and just shoot.
The camera can also detect and focus on faces, setting the color and
brightness to optimal levels.
Turn on the camera.
● Press the ON/OFF button.
X The start-up sound will play, and the startup screen will appear.
● Pressing the ON/OFF button again will
turn the camera off.
Choose A mode.
● Set the mode switch to A.
● When you point the camera toward the
subject, the camera will make a slight
noise as it determines the scene.
X The camera focuses on the subject it
judges to be the main subject, and the
icon for the determined scene appears in
the upper right of the screen.
X When faces are detected, a white frame
appears on the face of the main subject,
while gray frames appear on other
detected faces.
X A white frame will follow a detected face
that is moving and the gray frames will
disappear.
Compose the shot.
● Moving the zoom lever toward i will
zoom in on your subject, making it appear
larger. Moving the lever toward j will
zoom out from your subject, making it
appear smaller.
24
Taking Pictures
Focus.
● Press the shutter button halfway to focus.
X When the camera focuses, it will beep
twice and the indicator will light green
(orange when the flash will fire).
X Green AF frames appear where the
subject is in focus.
X Several AF frames will appear when the
camera focuses on more than one point.
X When a moving face is detected, and you
AF Frames
keep the shutter button pressed halfway,
a blue AF frame appears and the focus
and exposure are continuously adjusted.
Shoot.
● Press the shutter button fully.
X The camera will play the shutter sound
and shoot. The flash will automatically fire
in low light conditions.
X The indicator will blink green while the
image is recorded to the memory card.
X The image will appear on the screen for
about two seconds.
● You can take a second picture even while
an image is displayed by pressing the
shutter button again.
What if...
•a
flashing appears?
Attach the camera to a tripod so that the camera does not move and blur the
image.
• the camera does not play any sounds?
Pressing the l button while turning on the camera power will turn off all
sounds except for warning sounds. To turn the sounds on, press the n
button, choose the 3 tab, and then choose [Mute]. Use the qr buttons to
choose [Off].
25
Taking Pictures
• the image comes out dark even if the flash fired when shooting?
The subject is too far away for the flash to reach. Shoot within the effective flash
range of approximately 30 cm – 4.0 m (12 in. – 13 ft.) at maximum wide angle,
and approximately 50 cm – 2.0 m (1.6 – 6.6 ft.) at maximum telephoto.
• the camera beeps once when the shutter button is pressed halfway?
Your subject is too close. When the camera is at maximum wide angle, move
about 3 cm (1.2 in.) or more away from your subject and shoot. Move about
50 cm (1.6 ft.) or more away when the camera is at maximum telephoto.
• the lamp lights when the shutter button is pressed halfway?
To reduce red-eye and to assist in focusing, the lamp may light when shooting in
dark areas.
• the h icon blinks when you try to take an image?
The flash is charging. You can shoot when recharging ends.
Scene Icons
The camera displays an icon for the scene it has determined and then
automatically focuses and selects the optimum settings for subject
brightness and color.
Background
Subject
Bright
Backlit
Including Blue
Skies
Dark
Sunsets
When Using
Tripod
Backlit
People
–
When Moving
–
*
–
–
Subjects Other Than
People/
Landscapes
*
Close Subjects
Icon Background
Color
–
Gray
Light Blue
Orange
–
Dark Blue
* Appears when the camera is attached to a tripod.
Under certain conditions, the icon that appears may not match the actual
scene. Especially when there is an orange or blue colored background (a
wall for example),
or the “Blue Skies” icons may appear and it may
not be possible to shoot with the appropriate color. If this happens, try
shooting in G mode (p. 66).
26
Viewing Images
You can view your images on the screen.
Enter Playback mode.
● Press the 1 button.
X The last image you took will appear.
Choose an image.
● Pressing the q button will cycle through the
images in reverse order.
● Pressing the r button will cycle through
the images in the order they were taken.
● The images change more quickly if you
keep the qr buttons pressed.
● Pressing the shutter button halfway in
Playback mode switches the camera to
Shooting mode.
● The lens will retract after approximately 1
minute elapses.
27
Erasing Images
You can choose and erase images one at a time. Please note that erased
images cannot be recovered. Exercise adequate caution before erasing an
image.
Enter Playback mode.
● Press the 1 button.
X The last image you took will appear.
Choose an image to erase.
● Press the qr buttons to display an image
to erase.
Erase the image.
● Press the p button.
X [Erase?] appears.
● Press the qr buttons to choose [Erase],
then press the m button.
X The displayed image will be erased.
● To exit instead of erasing, press the qr
buttons to choose [Cancel], then press the
m button.
28
Printing Images
You can easily print the images you have taken if you connect the camera to
a PictBridge compliant printer (sold separately).
Items to Prepare
• Camera and PictBridge compliant printer (sold separately)
• Interface cable supplied with the camera (p. 2)
Turn off the camera and printer.
Connect the camera to the printer.
● Open the cover, and insert the small end
of the plug firmly into the camera terminal
in the direction shown.
● Insert the cable’s larger plug into the
printer. For connection details, refer to the
user guide provided with the printer.
Turn on the printer.
Turn on the camera.
● Press the 1 button to turn on the camera.
Choose an image to print.
● Press the qr buttons to choose an
image.
29
Printing Images
Print images.
● Press the m button, then press the op
buttons to choose 2 and press the m
button.
X The Print Settings screen will appear.
● Press the op buttons to choose [Print]
and press the m button.
X Printing will start.
● If you want to print additional images,
repeat Steps 5 and 6 after printing has
completed.
● After printing has completed, turn off the
camera and printer, and unplug the
interface cable.
• Refer to the Personal Printing Guide for details on printing.
• Refer to p. 39 for Canon-brand Pictbridge compliant printers.
30
Shooting Movies
The camera can automatically select all settings so that you can shoot
movies just by pressing the shutter button. If you continue shooting for a long
time, the camera may become warm. This is not a malfunction.
Set the mode switch to E.
Shooting Time
Compose the shot.
● Moving the zoom lever toward i will
zoom in on your subject, making it appear
larger. Moving the lever toward j will
zoom out from your subject, making it
appear smaller.
Focus.
● Press the shutter button halfway to focus.
X When the camera focuses, it will beep
twice and the indicator will light green.
31
Shooting Movies
Shoot.
● Press the shutter button fully.
X The camera will start shooting the movie,
Elapsed Time
Microphone
and [ Rec] and the elapsed time will
appear on the screen.
● Once shooting begins, take your finger off
the shutter button.
● If you change the composition of your shot
during shooting, the focus will stay the
same, but the brightness and tone will
automatically adjust.
● You can zoom in and out with the zoom
lever while shooting.
● Do not touch the microphone while
shooting.
● Do not press any buttons other than the
shutter button. Otherwise, the sound the
buttons make will be recorded in the
movie.
Stop shooting.
● Press the shutter button fully again.
X The camera will beep once and stop
shooting the movie.
X The indicator will blink green, and the
movie will record to the memory card.
X Shooting will automatically stop when the
memory card fills.
Estimated Shooting Times
Memory Card
Shooting Time
2 GB
10 min. 53 sec.
8 GB
43 min. 32 sec.
• Shooting times are based on default settings.
• Maximum clip length is approx. 10 minutes.
• Recording may stop even if the maximum clip length has not been reached on
some memory cards. SD Speed Class 4 or higher memory cards are
recommended.
32
Viewing Movies
You can view your movies on the screen.
Enter Playback mode.
● Press the 1 button.
X The last image you shot will appear.
X
appears on movies.
Choose a movie.
● Press the qr buttons to choose a movie,
then press the o button.
X The movie control panel will appear on the
screen.
Play the movie.
● Press the qr buttons to choose
(Play), then press the m button.
X The movie will play.
● You can pause/resume the movie by
pressing the m button again.
● Press the op buttons to adjust the
volume.
X After the movie finishes,
appears.
When watching a movie on a computer, frames may drop, it may not play
smoothly, and the audio may stop suddenly depending on the computer’s
capabilities. If you use the supplied software to copy the movie back onto
the memory card, you can play back the movie smoothly. For enhanced
playback you can also connect the camera to a TV.
33
Transferring Images to a Computer
You can use the included software to transfer your camera images to a
computer. If you are already using ZoomBrowser EX/ImageBrowser, install
the software from the included CD-ROM, overwriting your current
installation.
System Requirements
Windows
OS
Computer model
CPU
RAM
Interface
Free Hard Disk
Space
Display
Windows Vista (including Service Pack 1, Service Pack 2)
Windows XP Service Pack 2, Service Pack 3
The above OS should be pre-installed on computers with built-in
USB ports.
Viewing images Pentium 1.3 GHz or higher
Viewing movies Core2 Duo 1.66 GHz or higher
Windows Vista: 1 GB or more
Viewing images
Windows XP: 512 MB or more
Viewing movies 1 GB or more
USB
ZoomBrowser EX: 200 MB or more*
PhotoStitch: 40 MB or more
1,024 x 768 pixels or higher
* For Windows XP, Microsoft .NET Framework 3.0 or later (max. 500 MB) must be
installed. Installation may take some time depending on your computer's capabilities.
Macintosh
OS
Computer model
CPU
RAM
Interface
Free Hard Disk
Space
Display
34
Mac OS X (v10.4 – v10.5)
The above OS should be pre-installed on computers with built-in
USB ports.
Viewing images PowerPC G4/G5 or Intel Processor
Viewing movies Core Duo 1.66 GHz or higher
Viewing images 512 MB or more
Viewing movies 1 GB or more
USB
ImageBrowser: 300 MB or more
PhotoStitch: 50 MB or more
1,024 x 768 pixels or higher
Transferring Images to a Computer
Items to Prepare
• Camera and computer
• DIGITAL CAMERA Solution Disk supplied with the camera (p. 2)
• Interface cable supplied with the camera (p. 2)
Preparations
Windows Vista and Mac OS X (v10.5) are used for these explanations.
Install the software.
Windows
Place the DIGITAL CAMERA Solution
Disk in the computer’s CD-ROM drive.
Begin installation.
● Click [Easy Installation] and follow the
onscreen instructions to proceed with the
installation.
● If the [User Account Control] window
appears, follow the onscreen instructions
to proceed.
When the install finishes, click
[Restart] or [Finish].
Remove the CD-ROM.
● Remove the CD-ROM when your desktop
screen appears.
Macintosh
● Place the CD-ROM in the computer's CDROM drive and double-click the
icon.
● Click [Install], and follow the onscreen
instructions to proceed with the
installation.
35
Transferring Images to a Computer
Connect the camera to the
computer.
● Turn off the camera.
● Follow Step 2 on p. 29 to connect the
camera to a computer.
Turn on the camera.
● Press the 1 button to turn on the camera.
Open CameraWindow.
Windows
● Choose [Downloads Images From Canon
Camera using Canon CameraWindow].
X CameraWindow will appear.
● If CameraWindow does not appear, click
the [Start] menu and choose
[All Programs], followed by [Canon
Utilities], [CameraWindow],
[CameraWindow] and [CameraWindow].
Macintosh
X CameraWindow will appear when you
establish a connection between the
camera and computer.
● If CameraWindow does not appear, click
the CameraWindow icon on the Dock (the
bar which appears at the bottom of the
desktop).
36
Transferring Images to a Computer
Transfer Images
● Click [Import Images from Camera], and
then click [Import Untransferred Images].
X All images not previously transferred will
transfer to the computer. Transferred
images will be sorted by date and saved in
separate folders in the Pictures folder.
● After the transfer finishes, click [x] to close
CameraWindow, then turn off the camera
and unplug the cable.
● For further operations, refer to the
Software Guide.
You can transfer images without installing the included software by simply
connecting your camera to a computer. There are, however, the following
limitations:
• After connecting to the camera, it may take a few minutes until you can
transfer images.
• The camera information may not display correctly.
• Movies may not transfer correctly.
• Images shot vertically may be transferred in the horizontal orientation.
• Protection settings for images may be lost when transferred to a
computer.
• There may be problems transferring images or image information
correctly depending on the version of the operating system in use, the
file size, or the software in use.
37
Accessories
Supplied with Camera
AV Cable
AVC-DC400*1
Wrist Strap
WS-DC7
Interface Cable
IFC-400PCU*1
Battery Pack NB-4L*1
(with Terminal Cover)
DIGITAL CAMERA
Solution Disk
Battery Charger
CB-2LV/CB-2LVE*1
AC Adapter Kit ACK-DC10
DC Coupler
DR-10
Power Cord
Waterproof Case
WP-DC33
Compact Power Adapter
CA-DC10
*1 Also available for purchase separately.
*2 See the user guide supplied with the printer for more information on the printer and
interface cables.
38
Accessories
HDMI Cable HTC-100
High-Definition TV
Video IN Terminal
Audio IN Terminal
TV/Video
Canon-Brand PictBridge Compliant Printers*2
Compact Photo Printers
(SELPHY series)
High-Power Flash
HF-DC1
Memory Card
Card Reader
Inkjet Printers
Windows/Macintosh
Use of genuine Canon accessories is recommended.
This product is designed to achieve excellent performance when used with genuine
Canon accessories. Canon shall not be liable for any damage to this product and/or
accidents such as fire, etc., caused by the malfunction of non-genuine Canon
accessories (e.g., a leakage and/or explosion of a battery pack). Please note that this
warranty does not apply to repairs arising out of the malfunction of non-genuine Canon
accessories, although you may request such repairs on a chargeable basis.
39
Separately Sold Accessories
The following camera accessories are sold separately.
Some accessories are not sold in some regions, or may no longer be
available.
Power Supplies
• AC Adapter Kit ACK-DC10
This kit lets you power the camera using household power. Recommended for
powering the camera for an extended period of time or when connecting to a
computer. Cannot be used to charge the battery inside the camera.
• Battery Charger CB-2LV/CB-2LVE
An adapter for charging Battery Pack NB-4L.
• Battery Pack NB-4L
Rechargeable lithium-ion battery.
Other Accessories
• HDMI Cable HTC-100
Use this cable to connect the camera to the HDMI™ terminal on a high-definition
TV set.
• Waterproof Case WP-DC33
Installing the camera into this waterproof case lets you take underwater shots at
depths down to 40 meters (130 feet), or take worry-free pictures in the rain, at
the beach, or on the ski slopes.
• High-Power Flash HF-DC1
This attachable supplementary flash can illuminate subjects that are too distant
for the light from the built-in flash to reach.
40
2
Learning More
This chapter explains the parts of the camera and what appears on
the screen, as well as the basic operating instructions.
41
Components Guide
Lamp (Self-Timer Lamp (p. 64) /
AF Assist Beam (p. 136) / Red-Eye
Reduction Lamp (p. 136))
Lens
Zoom Lever
Shooting: i (Telephoto) / j (Wide
Angle) (p. 24)
Playback: k (Magnify) (p. 110)/ g
(Index) (p. 104)
Shutter Button (p. 23)
ON/OFF Button
Speaker
Flash (pp. 59, 67)
Microphone (p. 32)
Tripod Socket
DC Coupler Terminal Cover (p. 142)
Memory Card / Battery Cover (p. 16)
Mode Switch
Use the mode switch to change the Shooting mode.
Auto Mode
You can leave it to the camera to select settings (p. 24).
You can shoot with the best settings for the scene
(p. 56) or select settings yourself to take various
types of pictures (pp. 55, 65, 79).
Movie Mode
For shooting movies (pp. 31, 95).
42
Components Guide
Screen (LCD Monitor) (p. 44)
Mode Switch
1 (Playback) Button (pp. 27, 103)
Indicator (p. 46)
HDMI Terminal (p. 112)
A/V OUT (Audio/Video Output)
DIGITAL Terminal
Strap Mount (p. 13)
n Button (p. 48)
l (Display) Button (pp. 44, 45)
b (Exposure) (p. 66) / o Button
e (Macro) (p. 67) / u (Infinity) (p. 68) /
q Button
m FUNC./SET (Function/Set) Button
(p. 47)
h (Flash) (pp. 59, 67) / r Button
a (Single Image Erase) (p. 28) /
Q (Self-Timer) (pp. 63, 64) / p Button
1 Button
When the lens is extended, you can switch between the Shooting and
Playback modes. When the lens is retracted, you can use this button to turn
the camera on and off in Playback mode.
43
Information Displayed on the Screen
Shooting (Information Display)
Battery Charge Indicator
(p. 15)
Camera Orientation*
White Balance (p. 72)
My Colors (p. 74)
i-Contrast (p. 87)
Drive Mode (p. 73)
Camera Shake Warning
(p. 138)
Metering Modes (p. 84)
Compression (Image
Quality) (p. 69)
Recording Pixels (p. 69)
*
Still Images: Recordable
shots (p. 18)
Movies: Remaining Time/
Elapsed Time (p. 32)
Self-Timer (pp. 63, 64, 76)
AF Frame (p. 25)
Spot AE Point Frame
(p. 84)
Digital Zoom Magnification
(p. 60), Digital TeleConverter (p. 61)
Macro (p. 67),
Infinity (p. 68),
AF Lock (p. 82)
Shooting Mode
Flash Mode (pp. 59, 67)
Red-Eye Correction
(p. 88)
Time Zone (p. 135)
Image Stabilizer (p. 138)
Date Taken/Recorded
(p. 62)
ISO Speed (p. 71)
Disp. Overlay (p. 138)
AE Lock (pp. 85, 98),
FE Lock (p. 85)
Shutter Speed
Aperture Value
Exposure Compensation
(p. 66)
: Standard,
: Held vertically
When shooting, the camera detects if it is held vertically or horizontally, and
adjusts settings accordingly for the best shot. It also detects orientation during
playback, so you can hold the camera in either orientation and it will
automatically rotate images for correct viewing.
This function may not operate correctly when the camera is pointed straight up or down.
Switching the Display
You can change the display using the l button.
Information Display
44
No Information Display
Information Displayed on the Screen
Playback (Detailed Information Display)
Print List (p. 126)
My Category (p. 118)
Shooting Mode
ISO Speed (p. 71)
Exposure Compensation
(p. 66), Exposure Shift
(p. 98)
White Balance (p. 72)
Histogram (p. 46)
Image Editing
(pp. 121 – 125)
Compression (Image
Quality) (p. 69),
(Movies) (p. 97)
Recording Pixels (p. 69)
Battery Charge Indicator
(p. 15)
Metering Modes (p. 84)
Folder Number – File
Number (p. 132)
Displayed image
number / Total number of
images
Shutter Speed
Aperture Value, Image
Quality (Movies) (p. 97)
i-Contrast (p. 124)
Flash (p. 67)
Macro (p. 67),
Infinity (p. 68)
File Size (pp. 69, 97)
Still Images: Recording
Pixels (p. 69)
Movies: Movie Length
(p. 97)
Protect (p. 113)
My Colors (p. 74)
Red-Eye Correction
(p. 125)
Shooting Date and Time
(p. 62)
Switching the Display
You can change the display using the l button.
No Information
Display
Simple Information
Display
Detailed Information
Display
Focus Check Display
(p. 109)
You can also switch the display by pressing the l button while the
image displays shortly after shooting. However, Simple Information will
not display. You can set the display that appears first. Press the n
button to choose the 4 tab. Then set [Review Info].
45
Indicator
Display in Dark Conditions during Shooting
The display automatically brightens when shooting in dark conditions,
allowing you to check the composition (Night Display function). However, the
brightness of the image on the screen, and the brightness of the actual
image recorded may be different. Screen noise may appear and the
movement of the subject may appear somewhat jagged on the screen. This
has no effect on the recorded image.
Overexposure Warning during Playback
In “Detailed Information Display” (p. 45), overexposed areas of the image
flash on the screen.
Histogram during Playback
High
Low
Dark
Bright
● The graph that appears in “Detailed
Information Display” (p. 45) is called the
histogram. The histogram shows the
distribution and amount of brightness of
an image. When the graph approaches
the right side, the image is bright, but
when it approaches the left side, the
image is dark, and in this way you can
judge the exposure.
Indicator
The Indicator on the back of the camera (p. 43) will light or blink under the
following conditions.
Colors
Green
Orange
Status
Lights
Blinks
Lights
Blinks
Operation Status
Shooting preparation complete (p. 25)/Display Off (p. 134)
Recording/reading/transmitting image data (p. 25)
Shooting preparation complete (flash on) (p. 25)
Camera shake warning (p. 59)
When the indicator blinks green, data is being recorded to/read from the
memory card or various information is being transmitted. Do not turn off
the power, open the memory card slot/battery cover, shake or jolt the
camera. These actions may corrupt the image data or cause the camera
or memory card to malfunction.
46
FUNC. Menu – Basic Operations
You can set commonly used functions using the FUNC. menu. The menu
items and options differ depending on the mode (p. 148). You can also use
the FUNC. menu in Playback mode.
Display the FUNC. menu.
● Press the m button.
Choose a menu item.
● Press the op buttons to choose a menu
item, then press the m button.
● Depending on the menu, the screen may
switch. Choose a menu item and make
the setting.
Selectable Options
Menu Items
Choose an option.
● Press the op buttons to choose an
option.
● To return to the menu, press the q button.
Make the setting.
● Press the m button.
47
MENU – Basic Operations
Various functions can be set from the menus. The menu items are organized
under tabs, such as for shooting (4) and playback (1). The available
menu items differ depending on the mode (pp. 150 – 153).
Display the menu.
● Press the n button.
Choose a tab.
● Press the qr buttons, or move the zoom
lever (p. 42) left or right to choose a tab.
Choose a menu item.
● Press the op buttons to choose a menu
item.
● Some items require you to press the m
button or r button to display a submenu in
which you change the setting.
Choose an option.
● Press the qr buttons to choose an
option.
Make the setting.
● Press the n button.
X The normal screen will reappear.
48
Changing the Sound Settings
You can silence or adjust the volume of camera sounds.
Muting Sounds
Display the menu.
● Press the n button.
Choose [Mute].
● Press the qr buttons to choose the 3
tab.
● Press the op buttons to choose [Mute],
then use the qr buttons to choose [On].
Adjusting the Volume
Display the menu.
● Press the n button.
Choose [Volume].
● Press the qr buttons to choose the 3
tab.
● Press the op buttons to choose
[Volume], then press the m button.
Change the volume.
● Press the op buttons to choose an item,
then use the qr buttons to adjust the
volume.
49
Changing the Screen Brightness
The screen brightness can be changed in two ways.
With the Menu
Display the menu.
● Press the n button.
Choose [LCD Brightness].
● Press the qr buttons to choose the 3
tab.
● Press the op buttons to choose [LCD
Brightness],
Change the brightness.
● Press the qr buttons to change the
brightness.
● Press the n button again to complete
the setting.
With the l Button
● Press the l button for more than one
second.
X The screen increases to maximum
brightness regardless of the setting in the
3 tab.
● Pressing the l button again for more
than one second will return the screen to
the original brightness.
• The next time you turn on the camera, the screen will be at the
brightness setting chosen in the 3 tab.
• When you have set the brightness to its highest setting in the 3 tab, you
cannot change the brightness with the l button.
50
Returning the Camera to Default Settings
When you have mistakenly changed a setting, you can reset the camera to
the default settings.
Display the menu.
● Press the n button.
Choose [Reset All].
● Press the qr buttons to choose the 3
tab.
● Press the op buttons to choose [Reset
All], then press the m button.
Reset the settings.
● Press the qr buttons to choose [OK],
then press the m button.
X The camera will reset to the default
settings.
Are there functions that cannot be reset?
• The [Date/Time] (p. 19) in the 3 tab, [Language] (p. 21), [Video System]
(p. 111), [Time Zone] (p. 135), the image registered as [Start-up Image] (p. 139).
• The saved data for custom white balance (p. 72).
• Colors that were chosen in Color Accent (p. 91) or Color Swap (p. 92).
51
Low Level Memory Card Formatting
Perform low level formatting when you think that the recording/reading
speed of a memory card has dropped. As you cannot retrieve the erased
data, exercise adequate caution before low level formatting the memory
card.
Display the menu.
● Press the n button.
Choose [Format].
● Press the qr buttons to choose the 3
tab.
● Press the op buttons to choose
[Format], then press the m button.
Perform the low level format.
● Press the op buttons to choose [Low
Level Format], then use the qr buttons to
display
.
● Press the opqr buttons to choose
[OK], then press the m button.
X Low level formatting starts.
About low level formatting
When the [Memory card error] message appears, or when the camera does not
work correctly, low level formatting the memory card may solve the problem.
Copy the images from the memory card to a computer or other device before low
level formatting.
• Low level formatting may take longer than standard formatting (p. 22),
since all recorded data are erased.
• You can stop a low level format of a memory card by choosing [Stop].
When stopping low level formatting, the data will be erased but the
memory card can be used without problem.
52
Power Saving Function (Auto Power Down)
To save battery power, the camera shuts down automatically when it is not
operated for a certain time.
Power Saving during Shooting
The monitor will turn off approximately 1 minute after the camera is last
operated. After about 2 more minutes, the lens will retract and the power will
turn off. When the monitor has turned off but the lens has not yet retracted,
pressing the shutter button halfway (p. 23) turns on the monitor and shooting
can continue.
Power Saving during Playback
The power will turn off approximately 5 minutes after the camera is last operated.
• You can turn off the Power Saving Function (p. 134).
• You can adjust the time before the monitor turns off (p. 134).
53
Clock Functions
You can check the current time.
● Press and hold the m button.
X A screen like that on the left appears
showing the current time.
● If you hold the camera vertically while
using the clock function, it will switch to
vertical display. Press the qr buttons to
change the display color.
● Press the m button to cancel the clock
display.
When the camera power is off, press and hold the m button, then press
the ON/OFF button to display the clock.
54
3
Shooting in Special
Conditions and Commonly
Used Functions
This chapter explains how to shoot in different conditions, as well as
how to use common functions, such as the flash and self-timer.
• When you choose a Shooting mode that matches a particular set of
conditions, the camera will automatically select any necessary settings.
All you need do is press the shutter button to take an optimized picture.
• This chapter assumes the mode is set to A for “Turning the Flash Off”
(p. 59) to “Using the Face Self-Timer” (p. 64).
55
Shooting in Various Conditions
The camera will select the necessary settings for the conditions in which you
wish to shoot when you choose the matching mode.
Set the mode switch to 4.
Choose the desired shooting
mode.
● After pressing the m button, press the
op buttons to choose G, then press the
m button.
● Press the op buttons to choose the
desired mode, then press the m button.
Shoot.
I Take portraits (Portrait)
● Produces a soft effect when
photographing people.
F Take snapshots at night
(Night Snapshot)
● Lets you take beautiful snapshots of
people against city nightscapes or night
backgrounds.
● If you hold the camera firmly, you can take
pictures with reduced camera shake, even
without a tripod.
V Take shots of kids and pets
(Kids&Pets)
● Lets you capture subjects that move
around, such as children and pets, without
missing photo opportunities.
56
Shooting in Various Conditions
H Take indoor shots (Indoor)
● Lets you shoot indoors with natural colors.
U Shoot sunsets (Sunset)
● Lets you take shots of sunsets in vivid
colors.
t Take shots of fireworks
(Fireworks)
● Lets you take shots of fireworks in vivid
colors.
w Take shots of people at the beach
(Beach)
● Lets you take bright shots of people on
sandy beaches where the reflected
sunlight is strong.
S Shoot underwater (Underwater)
● Lets you shoot underwater with
Waterproof Case WP-DC33 (sold
separately).
57
Shooting in Various Conditions
y Take shots of aquatic life in an
aquarium (Aquarium)
● Lets you take natural-colored shots of
aquatic life in indoor aquariums.
O Take shots of foliage (Foliage)
● Lets you shoot trees and leaves, such as
new growth, autumn leaves or blossoms,
in vivid colors.
P Take shots of people in snow
(Snow)
● Lets you take bright, natural-colored shots
of people against snowy backgrounds.
Z Shoot using high ISO speed
(ISO 3200)
● Lets you set the ISO speed to 3200, and
lets you shoot without camera shake or
subject blurring even in low light
conditions.
● Recording pixels are set to
(1600 x
1200 pixels, p. 69).
• In F, V, H, S or y mode, images may appear coarse because the
ISO speed (p. 71) is increased to match the shooting conditions.
• In t mode, attach the camera to a tripod to prevent the camera from
moving and blurring the image. Additionally, you are recommended to
set [IS Mode] to [Off] (p. 138).
• In Z mode, images may appear coarse.
58
Turning the Flash Off
You can shoot with the flash turned off.
Press the r button.
Choose !.
● Press the qr buttons to choose !, then
press the m button.
X ! will appear on the screen.
● Follow the steps above to return the
setting to
.
What if the indicator blinks orange and a flashing
appears?
When you press the shutter button halfway in low light conditions where camera
shake is likely, the indicator will blink orange and a flashing
will appear on the
screen. Attach the camera to a tripod to prevent it from moving.
59
Zooming in More Closely on Subjects
(Digital Zoom)
You can use the digital zoom to zoom up to a maximum of 16x and capture
subjects that are too far away for the optical zoom (p. 24) to enlarge. The
images may appear coarse, however, depending on the recording pixel
setting (p. 69) and the zoom factor used.
Move the zoom lever toward i.
● Hold the lever until zooming stops.
X The zoom will stop when the largest
possible zoom factor without image
deterioration has been reached. The
zoom factor will appear when you release
the zoom lever.
Move it toward i again.
X The digital zoom will zoom in even further
on the subject.
Zoom Factors at which Images Deteriorate
Recording Pixels
Optical Zoom
(28 – 112 mm)*
Digital Zoom
(112 – 448 mm)*
4.0x
4.9x
6.2x
10x
16x
: No image deterioration (zoom factor appears white)
: Image deterioration (zoom factor appears blue)
: Maximum zoom factor without deterioration (Safety Zoom)
* Focal length (35mm equivalent)
60
Zooming in More Closely on Subjects (Digital Zoom)
Turning off the digital zoom
To turn off the digital zoom, press the n button, choose the 4 tab, and
choose [Digital Zoom] and the [Off] option.
Digital Tele-Converter
The focal length of the lens can be increased by an equivalent of 1.5x or
2.0x. This enables a faster shutter speed and less chance of camera shake
than the zoom (including digital zoom) used by itself at the same zoom
factor.
The images may appear coarse, however, depending on the combination of
recording pixel (p. 69) and digital tele-converter settings used.
Choose [Digital Zoom].
● Press the n button.
● Press the qr buttons to choose the 4
tab, and press the op buttons to choose
[Digital Zoom].
Accept the setting.
● Press the qr buttons to choose [1.5x] or
[2.0x].
● Pressing the n button will restore the
shooting screen.
X The view will be enlarged and the zoom
factor will appear on the screen.
● To return to standard digital zoom, choose
[Digital Zoom] and the [Standard] option.
Combinations that Cause Image Deterioration
• Using [1.5x] at a recording pixel setting of
or
will cause image
deterioration (the zoom factor will display in blue).
• Using [2.0x] at a recording pixel setting of
,
or
will cause image
deterioration (the zoom factor will display in blue).
• The respective focal lengths when using [1.5x] and [2.0x] are 42.0 –
168 mm and 56.0 – 224 mm (35mm film equivalent).
• The digital tele-converter cannot be used together with the digital zoom.
61
Inserting the Date and Time
You can insert the shooting date and time in the lower right corner of an
image. Once inserted, however, they cannot be deleted. Be sure to check
beforehand that the date and time are correctly set (p. 19).
Choose [Date Stamp].
● Press the n button.
● Press the qr buttons to choose 4 tab,
and press the op buttons to choose
[Date Stamp].
Accept the setting.
● Press the qr buttons to choose [Date] or
[Date & Time].
● Press the n button again to accept
the setting.
X [DATE] will appear on the screen.
Shoot.
X The shooting date and time will be
recorded in the image's lower right corner.
● To restore to the original setting, choose
[Off] in Step 2.
Inserting and printing the date and time in images without
an embedded date and time
• Use the DPOF print settings (p. 128) to print.
• Use the included software to print.
Refer to the Software Guide for details.
• Connect the camera to a printer to print.
Refer to the Personal Printing Guide for details.
62
Using the Self-Timer
The self-timer can be used to shoot a group photo that includes the camera
operator. The camera will activate approximately 10 seconds after the
shutter button is pressed.
Press the p button.
Choose Ò.
● Press the op buttons to choose Ò, then
press the m button.
X Once set, Ò will appear.
Shoot.
● Press the shutter button halfway to focus
on the subject, then press it fully.
X When the self-timer starts, the lamp blinks
and the self-timer sound plays.
X Two seconds before the shutter releases,
the lamp and sound speed up (the lamp
remains lit when the flash will fire).
● To cancel shooting with the self-timer after
countdown has started, press the p
button.
● To restore the original setting, choose
in Step 2.
You can change the delay time and number of shots (p. 76).
63
Using the Face Self-Timer
Once you compose the shot, such as for a group photo, press the shutter
button, and enter the composition, the camera will take three shots in a row
two seconds after it detects your face (p. 80).
Choose ".
● Follow Step 2 on p. 63 and choose ".
Compose the shot and press the
shutter button halfway.
● Make sure a green frame appears on the
face focused on and white frames appear
on other faces.
Press the shutter button fully.
X The camera will enter shooting stand-by,
and [Look straight at camera to start count
down] will appear on the screen.
X The lamp will blink and the self-timer
sound will play.
Join the subjects and look at the camera.
X When the camera detects a new face, the
lamp and sound will speed up (the lamp
remains lit when the flash will fire), and
two seconds later the shutter will release.
X The second and third shots will continue in
succession.
● To restore the original setting, choose
in Step 2 on p. 63.
What if a face is not detected?
Even if your face is not detected after joining the subjects, the shutter will release
approximately 30 seconds later.
Changing the number of shots
For the screen in Step 1, press the n button, then press the qr buttons
to change the number of shots. Press the m button to accept the setting.
64
4
Choosing Settings Yourself
In this chapter you will learn how to use the various functions in G
mode to progressively advance your shooting skills.
• This chapter assumes that the mode switch is set to 4 and the camera is
in G mode.
• G stands for Program AE.
• “Zooming In on Close Subjects (Digital Macro)” (p. 68) assumes the mode
switch had been set to 4 and the R mode chosen.
• Before attempting to shoot using a function explained in this chapter in
modes other than G mode, check if the function is available in those
modes (pp. 148 – 151).
65
Shooting in Program AE
You can choose the settings for various functions to suit your preferences.
AE stands for Auto Exposure.
Set the mode switch to 4 (p. 42).
Choose G.
● Choose G in Step 2 on p. 56 and press
the m button.
Adjust the settings according to
your purposes (pp. 67 – 76).
Shoot.
What if the shutter speed and aperture value are displayed
in orange?
If a correct exposure cannot be obtained when pressing the shutter button
halfway, the shutter speed and aperture value display in orange. Try the following
settings to obtain the correct exposure.
• Turn on the flash (p. 67)
• Choose a higher ISO speed (p. 71)
Adjusting the Brightness
(Exposure Compensation)
You can adjust the standard exposure set by the camera in 1/3-stop
increments in the range of -2 to +2.
Choose the exposure compensation.
● Press the o button.
Adjust the brightness.
● While watching the screen, press qr
buttons to adjust the brightness and press
the o button.
66
Turning the Flash On
You can make the flash fire every time you shoot. At maximum wide angle,
the flash range is approximately 30 cm – 4.0 m (12 in. – 13 ft.), and at
maximum telephoto, it is 50 cm – 2.0 m (1.6 – 6.6 ft.)
Choose h.
● After pressing the r button, press the qr
buttons to choose h, then press the m
button.
X Once set, h will appear.
Shooting Close-ups (Macro)
You can shoot an object at a close distance or even shoot extreme closeups of it. The shooting range is approximately 3 – 50 cm (1.2 in. – 1.6 ft.)
from the end of the lens (when the zoom lever is pushed to maximum j).
Choose e.
● After pressing the q button, press the qr
buttons to choose e, then press the m
button.
X Once set, e will appear.
How can I take better close-ups?
• You are recommended to attach the camera to a tripod and shoot in Î, to
prevent the camera from moving and blurring the image (p. 75).
• You can reduce the AF frame size when you want to focus on a specific
portion of the subject (p. 80).
The edges of the image may darken if the flash fires.
67
Shooting Far Away Subjects (Infinity)
You can shoot landscapes and far away subjects. The focusing range is 3 m
(9.8 ft.) and greater from the camera.
Choose u.
● After pressing the q button, press the qr
buttons to choose u, then press the m
button.
X Once set, u will appear.
Zooming In on Close Subjects (Digital Macro)
You can zoom in on close subjects. The possible shooting range is
approximately 3 – 10 cm (1.2 – 3.9 in.) from the end of the lens. However,
you can zoom in even closer on the subject using the digital zoom.
The digital zoom may cause images to appear coarse at some recording
pixel settings (p. 69).
Set the mode switch to 4 (p. 42).
Choose R.
● Choose R in Step 2 on p. 56 and press
the m button.
X The optical zoom will lock at the maximum
wide angle.
Use the zoom lever to compose
the shot.
X The camera will zoom in and the zoom
factor will appear.
Zoom Factors at which Images Deteriorate
• No image deterioration (zoom factor appears white)
• Image deterioration (zoom factor appears blue)
Using Î
You are recommended to attach the camera to a tripod and shoot in Î, to prevent
the camera from moving and blurring the image (p. 75).
68
Changing the Recording Pixels
You can choose from six recording pixels (image size) settings.
Choose the recording pixels.
● Press the m button and choose
press the m button again.
, then
Change the recording pixels.
● Press the op buttons to choose an
option, then press the m button.
X The setting you chose will display on the
screen.
If you choose
, you cannot use Digital Zoom (p. 60) or Digital TeleConverter (p. 61).
Changing the Compression Ratio
(Image Quality)
You can choose from the following two levels of compression ratio (image
quality):
(Fine),
(Normal).
Choose the image quality.
● Press the m button and choose
press the m button again.
, then
Change the compression ratio.
● Press the op buttons to choose an
option, then press the m button.
X The setting you chose will display on the
screen.
69
Changing the Compression Ratio (Image Quality)
Approximate Values for Recording Pixels and Compression
Ratio
Recording Pixels
Compression
Ratio
Single Image Data
Size (Approx. KB)
Number of Recordable
Images
2 GB
8 GB
(Large)
12 M/4000 x 3000
3084
626
2505
1474
1280
5116
(Medium 1)
8 M/3264 x 2448
2060
930
3721
980
1920
7675
(Medium 2)
5 M/2592 x 1944
1395
1365
5457
695
2672
10679
(Medium 3)
2 M/1600 x 1200
558
3235
12927
278
6146
24562
(Small)
0.3 M/640 x 480
150
10245
40937
61406
(Widescreen)
4000 x 2248
84
15368
2311
830
3318
1105
1707
6822
• The values in the table are measured according to Canon standards and may change
depending on the subject, memory card and camera settings.
Approximate Values for Paper Size
A2
A3
A4, Letter size
5" x 7"
Postcard size
3.5" x 5"
70
●
Suitable for sending images as e-mail
attachments.
●
For printing on wide size paper.
Changing the ISO Speed
Choose the ISO speed.
● Press the m button and choose
press the m button again.
, then
Choose an option.
● Press the op buttons to choose an
option, then press the m button.
X The setting you chose will display on the
screen.
Automatically adjusts the ISO speed to the Shooting mode and shooting
conditions.
Low Fine weather conditions, outdoor shooting.
Cloudy, Twilight
High Nightscapes, Dark interiors
Changing the ISO speed
• Lowering the ISO speed results in sharper images, but there may be an
increased chance of image blurring in certain shooting conditions.
• Raising the ISO speed results in a faster shutter speed, reducing camera shake
and letting the flash reach greater distances to the subject. The images,
however, will appear coarse.
• When the camera is set to
, you can press the shutter button halfway
to display the automatically set ISO speed.
• With ISO 3200 you can set an even faster speed (p. 58).
71
Adjusting the White Balance
The white balance (WB) function sets the optimal white balance for natural
looking colors.
Choose the white balance.
● Press the m button and choose
press the m button again.
, then
Choose an option.
● Press the op buttons to choose an
option, then press the m button.
X The setting you chose will display on the
screen.
Auto
Automatically sets the optimal white balance for the shooting conditions.
Day Light
Fine weather conditions, outdoor shooting
Cloudy
Cloudy, shady, twilight conditions
Tungsten
Tungsten, bulb-type (3-wavelength) fluorescent lighting
Fluorescent
Warm-white fluorescent, cool-white fluorescent, warm-white-type
(3-wavelength) fluorescent lighting
Fluorescent H Daylight fluorescent, daylight-type (3-wavelength) fluorescent lighting
Custom
Manually sets a custom white balance.
Custom White Balance
You can adjust the white balance to the light source at the shooting location.
Make sure that you set the white balance under the light source of the actual
scene you will shoot.
● In Step 2 above, choose
.
● Make sure the entire screen is filled with a
white colored subject, then press the
l button.
X The tint on the screen will change when a
white balance data is set.
If you change camera settings after recording white balance data, the
tone may not turn out properly.
72
Continuous Shooting
You can shoot continuously at a fixed interval (0.8 shots/sec.).
Choose a Drive mode.
● Press the m button and choose
, then
press the m button again.
● Press the op buttons to choose W, then
press the m button.
Shoot.
X As long as you hold the shutter button down,
the camera will shoot successive images.
• Cannot be used with the self-timer (pp. 63, 64, 75, 76).
• For continuous shooting, the focus and exposure are locked when the
shutter button is pressed halfway.
• As the number of images increases, the shooting intervals may take
longer.
• If the flash fires, shooting intervals may take longer.
73
Changing the Tone of an Image (My Colors)
You can change the tone of an image to sepia or black and white when shooting.
Choose My Colors.
● Press the m button and choose
press the m button again.
, then
Choose an option.
● Press the op buttons to choose an
option, then press the m button.
X The setting you choose will display on the
screen.
My Colors Off
Vivid
Neutral
—
Emphasizes the contrast and color saturation for a vivid
impression.
Tones down the contrast and color saturation for neutral
hues.
Sepia
Sepia tones.
B/W
Black and white.
Positive Film
Combines the effects of Vivid Red, Vivid Green and Vivid
Blue to produce intense natural appearing colors like those
obtained with positive film.
Lighter Skin Tone
Makes skin tones lighter.
Darker Skin Tone
Makes skin tones darker.
Vivid Blue
Vivid Green
Emphasizes blue tints. Makes the sky, ocean and other
blue subjects more vivid.
Emphasizes green tints. Makes mountains, foliage and
other green subjects more vivid.
Vivid Red
Emphasizes red tints. Makes red subjects more vivid.
Custom Color
You can adjust contrast, sharpness, and color saturation
etc. to your preference (p. 75).
• The white balance cannot be set in the
and
modes (p. 72).
• In the
and
mode, colors other than people’s skin color may
change. You may not obtain the expected results with some skin colors.
74
Shooting Using the Two Second Self-Timer
Custom Color
The contrast, sharpness, color saturation, red, green, blue, and skin tones in
an image can be chosen and set from 5 different levels.
● Follow Step 2 on p. 74 to choose
, then
press the l button.
● Press the op buttons to choose an
option, then use the qr buttons to choose
a value.
● The more to the right, the stronger/deeper
the effect gets, the more to the left, the
weaker/lighter the effect gets.
● Press the l button to accept the
setting.
Shooting Using the Two Second Self-Timer
You can set the self-timer to a delay of approximately two seconds.
Choose Î.
● After pressing the p button, press the
op buttons to choose Î, then press the
m button.
X Once set, Î will appear on the screen.
● Follow Step 3 on p. 63 to shoot.
75
Customizing the Self-Timer
You can set the time delay (0 – 30 seconds) and the number of shots (1 – 10
shots).
Choose $.
● Press the p button, then use the op
buttons to choose $, then press the
n button.
Choose the settings.
● Press the op buttons to choose [Delay]
or [Shots].
● Press the qr buttons to choose a value,
then press the m button.
● Follow Step 3 on p. 63 to shoot.
What if the number of shots is set to two or more shots?
• Exposure and white balance settings are set with the first shot.
• When you set the time delay for more than 2 seconds, the self-timer lamp and
sound speed up 2 seconds before the shutter releases (when the flash will fire,
the lamp lights).
• If the flash fires, the shooting interval may be longer.
• If you set a high number of shots, the shooting interval may be longer.
• If the memory card becomes full, shooting stops automatically.
76
Shooting Using a TV Monitor
You can use a TV to display the camera screen content while shooting.
• Connect the camera to a TV as described in “Viewing Images on a TV” (p. 111).
• Shooting procedures are the same as when using the camera’s monitor.
TV display is not available when using the HDMI Cable HTC-100 (sold
separately) to connect the camera to a high-definition TV.
Changing the Composition with the
Focus Lock
While you keep the shutter button pressed halfway, the focus and exposure
are locked. You can now recompose and shoot. This is called Focus Lock.
Focus.
● Center the subject you want in focus, and
press the shutter button halfway.
● Confirm that a green AF frame appears
around the subject.
Recompose.
● Keep the shutter button pressed halfway
and recompose the scene.
Shoot.
● Press the shutter button fully.
77
78
5
Getting More Out of Your
Camera
This chapter serves as the advanced version of Chapter 4 and
explains how to take pictures using various functions.
• This chapter assumes that the mode switch is set to 4 and the camera is
in G mode.
• “Shooting Long Exposures” (p. 90), “Changing the Color and Shooting”
(p. 91) and “Shooting Stitch Assist Images” (p. 94) assume you have set
the mode switch to 4 and selected the corresponding mode.
• Before attempting to shoot using a function explained in this chapter in
modes other than G mode, check if the function is available in those
modes (pp. 148 – 151).
79
Changing the AF Frame Mode
You can change the AF (Auto Focus) frame mode to match the conditions
you want to shoot.
Choose [AF Frame].
● Press the n button, choose the 4
tab, and then choose the [AF Frame]
menu item. Use the qr buttons to choose
an option.
Face AiAF
• Detects people’s faces and sets the focus, exposure (evaluative metering
only) and white balance (
only).
• When the camera is pointed at subjects, a white frame appears on the
face the camera judges to be the main subject, and gray frames (max. 2)
will appear on other faces. When the shutter button is pressed halfway, up
to 9 green frames will appear on faces on which the camera focuses.
• If a face is not detected and only gray frames (no white frame) appear,
up to 9 green frames will appear on the areas the camera focuses on
when the shutter button is pressed halfway.
• Examples of faces that cannot be detected:
• Subjects that are far away or extremely close.
• Subjects that are dark or light.
• Faces turned to the side or at a diagonal, or faces with a portion hidden.
• The camera may mistakenly identify non-human subjects as a face.
• If the camera cannot focus when you press the shutter button halfway,
the AF frame will not appear.
Center
The AF frame is locked to the center. This is effective for focusing on a specific
point.
You can reduce the AF frame size
• Press the n button, choose the 4 tab, then choose the [AF Frame Size]
menu item and [Small] option.
• The setting is configured to [Normal] when the Digital Zoom (p. 60) or Digital
Tele-converter (p. 61) is used.
80
Magnifying the Focal Point
If the camera cannot focus when you press the shutter button halfway, the
AF frame will turn yellow and
will appear.
Magnifying the Focal Point
You can push the shutter button halfway to magnify the AF frame and check
the focus.
Choose [AF-Point Zoom].
● Press the n button, choose the 4
tab, and then choose the [AF-Point Zoom]
menu item. Use the qr buttons to choose
[On].
Check the focus.
● Press the shutter button halfway.
X In [Face AiAF], the face selected as the
main subject will appear magnified.
X In [Center], the contents of the center AF
frame will appear magnified.
What if the display does not magnify?
The display will not appear magnified in [Face AiAF] if a face cannot be detected
or is too big in relation to the screen. In [Center], it will not appear magnified if the
camera cannot focus.
The magnified display will not appear when using Digital Zoom (p. 60) or
Digital Tele-Converter (p. 61), Servo AF (p. 83), or when connected to a
TV (p. 77).
81
Shooting with the AF Lock
The focus can be locked. After locking the focus, the focal distance will not
change even when you release your finger from the shutter button.
Lock the focus.
● Keep the shutter button pressed halfway
and press the q button.
X The focus locks and % is displayed on
the screen.
● If you release your finger from the shutter
button and press the q button again, %
will disappear and the focus will unlock.
Compose the scene and shoot.
82
Shooting with Servo AF
While the shutter button is pressed halfway, the focus and exposure will
continue to adjust, allowing you to take pictures of moving subjects without
missing a shot.
Choose [Servo AF].
● Press the n button and choose
[Servo AF] on the 4 tab, and use the qr
buttons to choose [On].
Focus.
● Focus and exposure will be maintained
where the blue AF frame appears while
you press the shutter button halfway.
● If a face is not detected when AF Frame is
set to [Face AiAF], the AF frame will be
set to [Center].
• The camera may not be able to focus and exposure in some conditions.
• If a correct exposure cannot be obtained, the shutter speed and aperture
value are shown in orange. Take your finger off the shutter button, then
press it again halfway.
• You cannot shoot with the AF lock in this mode.
• You cannot set the Servo AF mode if you have set the [AF-Point Zoom]
option in the 4 tab to [On].
• Not available in Self-Timer (pp. 63, 64, 75, 76).
83
Changing the Metering Mode
You can change the Metering mode (brightness measuring function) to
match the shooting conditions.
Choose the Metering mode.
● Press the m button and choose
press the m button again.
, then
Choose an option.
● Press the op buttons to choose an
option, then press the m button.
X The setting will display on the screen.
Suitable for standard shooting conditions, including back
lit shots. Automatically adjusts the exposure to match the
the shooting conditions.
Averages the light metered from the entire frame, but
Center Weighted Avg.
gives greater weight to the center.
Only meters within the
(Spot AE Point frame) that
Spot
appears at the center of the screen.
Evaluative
84
Shooting with the AE Lock
When you wish to take several shots with the same exposure, you can set the
exposure and focus separately using the AE lock. AE stands for “Auto
Exposure”.
Lock the exposure.
● Point the camera toward the subject and
press the o button while pressing the
shutter button halfway.
X When & appears, the exposure will be
set.
● If you release your finger from the shutter
button and press the o button again, &
will disappear and the AE will unlock.
Compose the scene and shoot.
Shooting with the FE Lock
Just as with the AE lock (p. 85), you can lock the exposure for shooting with
the flash. FE stands for “Flash Exposure”.
Choose h (p. 67).
Lock the exposure.
● Point the camera toward the subject and
press the o button while pressing the
shutter button halfway.
X The flash will fire and when ( appears,
the flash output will be retained.
● If you release your finger from the shutter
button and press the o button again, (
will disappear and the FE will unlock.
Compose the scene and shoot.
85
Shooting with Slow Synchro
You can make the main subject, such as people, appear bright by having the
camera provide the appropriate illumination with the flash. At the same time,
you can use a slow shutter speed to brighten the background that the light
from the flash cannot reach.
Choose ….
● Press the r button, then use the qr
buttons to choose …, then press the m
button again.
X Once set, … will appear on the screen.
Shoot.
● Even if the flash fires, ensure that the
subject does not move until the shutter
sound ends.
Attach the camera to a tripod to prevent the camera from moving and
blurring the image. It is recommended to set the [IS Mode] to [Off] when
shooting with a tripod (p. 138).
86
Correcting the Brightness and Shooting
(i-Contrast)
The camera can detect areas in the scene, such as faces or backgrounds,
that are too bright or dark and automatically adjust them to the optimum
brightness when shooting. Also, when the overall image is lacking in
contrast, the camera will automatically correct the image for a sharper
impression when shooting.
Choose [i-Contrast].
● Press the n button, choose the 4
tab, and then choose the [i-Contrast]
menu item. Use the qr buttons to choose
[Auto].
X @ will appear on the screen.
Under some conditions, the image may appear coarse or may not be
corrected properly.
You can correct recorded images (p. 124).
87
Red-Eye Correction
You can automatically correct red-eye that occurs in images taken with the
flash.
Choose [Flash Settings].
● Press the n button, choose [Flash
Settings] from the 4 tab and press the
m button.
Adjust the setting.
● Press the op buttons to choose [RedEye Corr.] and press the qr buttons to
choose [On].
X Πwill appear on the screen.
Red-eye correction may be applied to red areas other than red eyes. For
example, when red make-up has been used around eyes.
• You can correct recorded images (p. 125).
• If you press the r button as shown on the screen in Step 2 and then
press the n button, the Flash Settings screen will appear.
88
Checking for Shut Eyes
When the camera detects the possibility that people have their eyes shut,
appears.
Choose [Blink Detection].
● Press the n button, choose the 4
tab, and then choose the [Blink Detection]
menu item. Use the qr buttons to choose
[On].
Shoot.
X When a person with shut eyes is detected,
a frame and
appear for a few seconds.
• In " and $ modes, this function is only available for the last image
shot.
• Not available in W.
89
Shooting Long Exposures
You can set the shutter speed to a range between 1 and 15 seconds to
shoot long exposures. However, you should attach the camera to a tripod to
prevent the camera from moving and blurring the image.
Select ≈.
● Choose ≈ in Steps 1 – 2 on p. 56 and
press the m button.
Select the shutter speed.
● Press the o button.
● Press the qr buttons to select shutter
speed, then press the m button.
Confirm the exposure.
● When you press the shutter button
halfway, the exposure for the selected
shutter speed will appear.
• The brightness of the image may differ from the brightness of the screen
in Step 3 when the shutter button was pressed halfway.
• When shutter speeds of 1.3 seconds or slower are used, images are
processed to eliminate noise after being taken. A certain amount of
processing time may be needed before you can take the next shot.
• It is recommended to set the [IS Mode] to [Off] when shooting with a
tripod (p. 138).
If the flash fires, the image may be overexposed. If this happens, set the
flash to ! and shoot.
90
Changing the Color and Shooting
You can change the look of an image when shooting. However, the shooting
conditions may cause the image to become coarse, or the colors may not
come out as expected.
T Color Accent
You can choose to retain a single color and change the rest to black and
white in a composition.
Choose T.
● Follow Steps 1 – 2 on p. 56 to choose T.
Press the l button.
● The unchanged image and the Color
Accent image will both display.
● The color for default settings is green.
Specify the color.
● Position the center frame so it is filled with
the color you want and press the q button.
X The specified color will be recorded.
Specify the range of colors.
● Press the op buttons to change the range
Recorded color
of colors to be retained.
● Choose a negative value to limit the range
of colors. Choose a positive value to
extend the range of colors to similar
colors.
● Pressing the l button accepts the
setting and restores the shooting screen.
Using the flash may cause unexpected results in this mode.
91
Changing the Color and Shooting
Y Color Swap
You can swap one color in an image for another when recording it. You can
only swap one color.
Choose Y.
● Follow Steps 1 – 2 on p. 56 to choose Y.
Press the l button.
● The unchanged image and the Color
Swap image will both display.
● The default setting is to change green to
gray.
Specify the color to be swapped.
● Position the center frame so it is filled with
the color you want and press the q button.
X The specified color will be recorded.
Specify the target color.
● Position the center frame so it is filled with
the color you want and press the r button.
X The specified color will be recorded.
92
Changing the Color and Shooting
Specify the range of colors to be
swapped.
● Press the op buttons to adjust the range
of colors affected.
● Choose a negative value to limit the range
of colors. Choose a positive value to
extend the range of colors to similar colors.
● Pressing the l button accepts the
setting and restores the shooting screen.
• Using the flash may cause unexpected results in this mode.
• Under some conditions, the image may appear coarse.
93
Shooting Stitch Assist Images
Large subjects can be split into several shots that can later be merged
together using the included software on a computer to create a panoramic
image.
Choose x or v.
● Follow Steps 1 – 2 on p. 56 to choose x
or v.
Take the first shot.
X The exposure and white balance will be
set with the first shot.
Take subsequent shots.
● Overlap part of the first shot when taking
the second shot.
● Minor discrepancies in the overlapping
portions will be corrected when the
images are merged.
● Up to 26 shots can be recorded with the
same procedures.
Finish shooting.
● Press the m button.
Merge the images on a computer.
● For details on how to merge the images,
refer to the Software Guide.
This function is not available when a TV is used as the monitor (p. 77).
94
6
Using Various Functions for
Shooting Movies
This chapter provides more advanced information than the "Shooting
Movies" and "Viewing Movies" sections of Chapter 1.
• This chapter assumes that the mode switch is set to E.
95
Changing the Movie Mode
You can choose between three Movie modes.
Set the mode switch to E.
Choose a Movie mode.
● Press the m button, then use the op
buttons to choose E, then press the m
button again.
● Press the op buttons to choose a
Shooting mode, then press the m button.
E Standard
Normal mode.
> Color Accent
These Shooting modes let you change all colors except the chosen
color to black and white, or exchange the chosen color for another
color, when shooting. See “Changing the Color and Shooting”
(p. 91) for details.
z Color Swap
Under some conditions, colors may not turn out as expected in the > and
z mode.
96
Changing the Image Quality
You can choose between three image quality settings.
Choose the image quality.
● Press the m button, then use the op
, then press the m
buttons to choose
button again.
Choose an option.
● Press the op buttons to choose an
option, and press the m button.
X The setting will display on the screen.
Image Quality Table
Image Quality
(Recording Pixels/Frame Rate)
Content
1280 x 720 pixels, 30 frames/sec. For shooting high-definition movies.
640 x 480 pixels, 30 frames/sec.
For shooting standard quality movies.
320 x 240 pixels, 30 frames/sec.
Since the number of recording pixels is smaller,
the image quality will be lower than with
,
but you can record three times the length.
Estimated Shooting Time
Image Quality
(Frame Rate)
Shooting Time
2 GB
8 GB
10 min. 53 sec.
43 min. 32 sec.
23 min. 49 sec.
1 hr. 35 min. 11 sec.
1 hr. 13 min. 10 sec.
4 hrs. 52 min. 24 sec.
• Based on Canon’s testing standards.
• Maximum clip length is approximately 10 minutes in
, 1 hour in
and
.
Recording also stops when the file size reaches 4 GB.
• Recording may stop even if the maximum clip length has not been reached on some
memory cards. SD Speed Class 4 or higher memory cards are recommended.
97
AE Lock/Exposure Shift
You can set the exposure or change it in 1/3 steps within a range of ±2.
Focus.
● Press the shutter button halfway to focus.
Lock the exposure.
● After releasing the shutter button, press
the o button to lock the exposure. The
exposure shift bar appears.
● Press the o button again to release the lock.
Change the exposure.
● While watching the screen, press the qr
buttons to adjust the brightness.
Shoot.
98
Other Shooting Functions
The following functions can be used in the same way as for still images. For
> and z modes, the functions with an * attached can be used in the same
way as for still images.
• Zooming in More Closely on Subjects (Digital Zoom) (p. 60)
You can use the digital zoom, but the optical zoom cannot be used.
If you want to shoot at the maximum zoom factor, you should adjust the optical
zoom to the maximum before shooting.
The sound of the zoom will be recorded.
• Using the Self-Timer (p. 63)*
• Shooting Close-ups (Macro) (p. 67)*
• Shooting Far Away Subjects (Infinity) (p. 68)*
• Adjusting the White Balance (p. 72)
• Changing the Tone of an Image (My Colors) (p. 74)
• Shooting Using the Two Second Self-Timer (p. 75)*
• Shooting Using a TV Monitor (p. 77)*
• Shooting with the AF Lock (p. 82)
• Turning off the AF Assist Beam (p. 136)*
• Displaying the Overlay (p. 138)*
[3:2 Guide] is not available.
• Changing the IS-Mode Settings (p. 138)*
You can switch between [Continuous] and [Off].
99
Playback Functions
The following functions can be used in the same way as for still images.
•
•
•
•
•
•
•
•
•
•
Erasing Images (p. 28)
Quickly Searching Images (p. 104)
Viewing Images in Filtered Playback (p. 106)
Viewing Slideshows (p. 107)
Changing Image Transitions (p. 110)
Viewing Images on a TV (p. 111)
Protecting Images (p. 113)
Erasing All Images (p. 115)
Organizing Images by Category (My Category) (p. 118)
Rotating Images (p. 120)
Summary for “Viewing Movies” (p. 33)
Exit
Playback
Slow Motion Playback (you can use the qr buttons to adjust the speed. Sound
will not play back.)
Display the first frame
Previous frame (Rewind if you hold down the m button.)
Next frame (Fast forward if you hold down the m button.)
Display the last frame
Edit (p. 101)
Appears when connected to a PictBridge compliant printer (p. 29).
Refer to the Personal Printing Guide for details.
100
Editing
You can trim the beginnings and ends of recorded movies in one-second
increments.
Choose *.
● Follow Steps 1 – 3 on p. 33, choose *
and press the m button.
X The movie editing panel and the movie
editing bar will appear.
Movie Editing Panel
Set the editing range.
● Press the op buttons and choose
Movie Editing Bar
or
.
● Press the qr buttons to move .
will
display at each one-second interval. If you
choose
, you can trim the beginning of
the movie from
. If you choose
, you
can trim the end of the movie from
.
X Even if you move to a point other than a
point, only the portion from the
nearest
to the left will be trimmed
when
is chosen. Only the portion from
the nearest
to the right will be trimmed
when
is chosen.
X The light blue section indicated with will
be the section of the movie that remains
after editing.
Check the edited movie.
● Press the op buttons to choose
(Play), then press the m button. The
edited movie will play.
● To edit the movie again, repeat Step 2.
● To cancel editing, press the op buttons,
and choose
. After pressing the m
button, press the qr buttons to choose
[OK], and press the m button again.
101
Editing
Save the edited movie.
● Press the op buttons to choose
,
then press the m button.
● Press the qr buttons to choose [New
File], then press the m button.
X The movie will be saved as a new file.
• When [Overwrite] is chosen in Step 4, the unedited movie is overwritten
with the edited movie, erasing the original movie.
• When there is not enough space left on the memory card, only
[Overwrite] can be chosen.
• If the battery is depleted partway through editing, the edited movie clips
may not be saved. When editing movies, you should use a fully charged
battery or the separately sold AC adapter kit (p. 40).
102
7
Using Playback and Other
Functions
The first part of this chapter explains various ways to play back and
edit images. The latter part explains how to specify images for printing.
• Press the 1 button to enter Playback mode before operating the camera.
• It may not be possible to play back or edit images that have been edited
on a computer, had their file name changed, or have been taken on a
different camera.
• The edit function (pp. 121 – 125) cannot be used if the memory card
does not have free space available.
103
Quickly Searching Images
g Searching Images Using Index Display
Displaying multiple images at a time lets you quickly find the image you want.
Move the zoom lever toward g.
X Images will display in an index.
● Move the zoom lever toward g to
increase the number of images. The
number of images increases each time
you move the lever.
● Move the zoom lever toward k to reduce the
number of images. The number of images
will reduce each time you move the lever.
Choose an image.
● Press the opqr buttons to choose an image.
● An orange frame appears on the chosen
image.
● Press the m button to display the chosen
image by itself.
Searching in a large number of images
By repeatedly moving the zoom lever toward g, you can display an index of up
to 100 images. If you move the zoom lever toward g again, a orange frame
appears around all of the images and you can quickly search by pressing the
op buttons to switch between sets of 100 images.
104
Quickly Searching Images
Searching Images by Scrolling
Pressing the qr buttons for more than one second will display images in a
line (Scroll Display) letting you quickly search them.
Choose an image.
● If you set single image playback and press
the qr buttons for more than one second,
the screen shown on the left will appear.
● If you press the op buttons, you can
search images by the shooting date.
● Pressing the m button restores single
image playback.
To turn off this effect, press the n button, then choose [Scroll Display]
in the 1 tab and choose [Off].
105
Viewing Images in Filtered Playback
When there are many images on the memory card, you can filter and display
them by a specified filter. You can also protect (p. 113) or delete (p. 115) all
images at once while filtered.
Choose ‚.
● Press the m button to choose ‚ in the
FUNC. menu, then press the m button
again.
Choose a filter.
● Press the op buttons to choose a filter,
then press the m button.
View the filtered images.
● Press the op buttons to choose a filter
for playback, then press the m button.
X Filtered playback starts and a yellow
frame appears.
● If you press the qr buttons, only the
chosen target images will display.
● If you choose [All Images] in Step 2,
filtered playback will be canceled.
Search by
, ; and
Shot Date
; My Category
File Type
Displays the images shot on a specified date
Displays the images of a specified category
Displays only still images or movies
What if you can’t choose a filter?
Filters that do not contain any images cannot be chosen.
Filtered Playback
You can filter images during a slideshow (p. 107) so that only certain images will
play back. You can also use the following functions in filtered playback for
processing all the filtered images at once.
• “Protecting Images” (p. 113), “Erasing All Images” (p. 115), “Printing from the
Print List (DPOF)” (p. 126)
106
Viewing Slideshows
You can automatically play back images recorded to a memory card. Each
image displays for approximately 3 seconds.
Choose ..
● Press the m button to choose . in the
FUNC. menu, then press the m button
again.
Choose a transition effect.
● Press the op buttons to choose an
effect and press the m button.
X The slideshow will start a few seconds
after [Loading image…] displays.
● In filtered playback (p. 106), only images
matching a filter play back.
● You can pause/restart a slideshow by
pressing the m button again.
● Press the n button to stop the
slideshow.
• If you press the qr buttons during playback, the image will switch. If you
keep the qr buttons pressed, you can fast-forward through images.
• The power saving function does not work during slideshows (p. 53).
107
Viewing Slideshows
Changing Settings
You can set a slideshow to repeat, or change transition effects and the time
that slideshow images are displayed. You can choose from six transition
effects when switching between images.
Choose [Slideshow].
● Press the n button, choose
[Slideshow] from the 1 tab and press the
m button.
Make the setting.
● Press the op buttons to choose an item,
and press the qr buttons to adjust the
setting.
● If you choose [Start] and press the m
button, the slideshow starts with your
settings.
● Pressing the n button will restore the
menu screen.
You cannot change [Play Time] if [Bubble] is chosen in [Effect].
108
Checking the Focus
You can magnify the area of a recorded image that was inside the AF Frame,
or the area of a face that was detected, to check the focus.
Press the l button, and switch
to the focus check display (p. 45).
X A white frame will appear where the AF
frame or face was when the focus was set.
X A gray frame will appear on a face
detected during playback.
X The area within the orange frame appears
magnified.
Switch frames.
● Move the zoom lever toward k once.
X The screen shown to the left will appear.
● Press m to move to a different frame
when multiple frames appear.
Change the magnification level or
location.
● Use the zoom lever to change the display
size, and the opqr buttons to change the
display position while checking the focus.
● Pressing the n button resets the
display to Step 1.
109
Magnifying Images
Move the zoom lever toward k.
● The display will zoom in on the image and
Approximate Location
of Displayed Area
will appear. If you continue to hold
the zoom lever, it will continue to zoom in
up to a factor of 10x.
● If you press the opqr buttons, you can
move the location of the displayed area.
● Move the zoom lever toward g to zoom
out or return to Single Image Playback.
● When
appears on the screen,
press the m button to switch to
.
Press the qr buttons to switch between
images at the same level of magnification.
Press the m button again to return to
.
Changing Image Transitions
You can choose from three transition effects when switching between
images in single image playback.
Choose [Transition].
● Press the n button and choose the
1 tab, then choose [Transition] and use
the qr buttons to choose a transition
effect.
110
Viewing Images on a TV
Using the supplied AV cable, you can connect the camera to a TV to view
images you have shot.
Items to Prepare
• Camera and TV
• AV cable supplied with the camera (p. 2)
Turn off the camera and TV.
Connect the camera to the TV.
● Open the camera’s terminal cover and
fully insert the plug of the cable into the
camera’s terminal.
● Insert the cable plug fully into the video
input terminals as shown in the illustration.
White or black
Yellow
Yellow
Turn on the TV and switch it to the
input to which the cable is
connected.
Black
Turn on the camera.
● Press the 1 button to turn on the camera.
X The image will appear on the TV (nothing
will appear on the monitor of the camera).
● After you finish viewing, turn off the
camera and TV, and unplug the AV cable.
What if the images don’t properly display on the TV?
Images will not display correctly if the camera’s video output setting (NTSC/PAL)
does not match the TV system. Press the n button, choose the 3 tab and
[Video System] to switch to the correct video system.
111
Viewing Images on a High-Definition TV
Use the separately sold HDMI cable HTC-100 to connect the camera to a
high-definition TV for an enhanced viewing experience.
Turn off the camera and TV.
Connect the camera to the TV.
● Open the cover and fully insert the cable
plug into the camera's HDMI terminal.
● Fully insert the cable plug into the TV's
HDMI terminal.
● Follow Steps 3 – 4 on p. 111 to display the
images.
The supplied AV and interface cables and the separately sold HDMI cable
HTC-100 cannot be plugged into the camera simultaneously. This could
cause the camera to malfunction.
Operation sounds will not play when connected to a high-definition TV.
112
Protecting Images
You can protect important images so that they cannot be erased by the
camera (pp. 28, 115).
Choose :.
● Press the m button to choose : in the
FUNC. menu, then press the m button
again.
X Once set,
will appear on the screen.
● To unlock an image, choose : from the
FUNC. menu and press the m button.
If you format the memory card (p. 52), protected images will also be
erased.
• Protected images cannot be erased with the camera’s erase function. To
erase an image, cancel protection first.
• You can also protect images using the following method. Press the
n button, choose the 1 tab, then choose [Protect]. Press the m
button to choose [Select] and press the m button again, then press the
qr buttons to choose an image and press the m button.
Select Range
Choose [Protect].
● Press the n button, choose the 1
tab and [Protect], and then press the m
button.
Choose [Select Range].
● Press the op buttons to choose [Select
Range] and press the m button.
● Pressing the n button will restore the
menu screen.
113
Protecting Images
Choose the starting image.
● Press the m button.
● Press the qr buttons to choose the
image and press the m button.
Choose the ending image.
● Press the r button, choose [Last image]
and press the m button.
● Press the qr buttons to choose an
image, and press the m button.
● You cannot choose images before the first
image.
Protect images.
● Press the p button, choose [Protect] and
press the m button.
114
Erasing All Images
Choose All Images
Choose [All Images].
● Follow Step 2 on p. 113 to choose [All
Images] and press the m button.
Protect images.
● Press the op buttons to choose [Protect]
and press the m button.
You can unlock groups of protected images if you choose [Unlock] in
Step 5 while in [Select Range], or Step 2 while in [All Images].
Erasing All Images
You can choose images and erase them in groups. Since erased images
cannot be recovered, exercise adequate caution before erasing. Protected
images (p. 113) cannot be erased.
Choose [Erase].
● Press the n button, choose the 1
tab and [Erase], and press the m button.
Choose a selection method.
● Press the op buttons to choose a
selection method, and press the m
button.
115
Erasing All Images
Choosing Images Individually
Choose [Select].
● Follow Step 2 on p. 115 to choose [Select]
and press the m button.
Choose images.
● Press the qr buttons to choose the
image and press the m button.
X Once set,
will appear on the screen.
● Pressing the m button once more will
cancel the selection, and
will
disappear.
● To choose multiple images, repeat the
above operation.
Press the n button.
Erase.
● Press the qr buttons to choose [OK] and
press the m button.
116
Erasing All Images
Select Range
Choose [Select Range].
● Follow Step 2 on p. 115 to choose [Select
Range] and press the m button.
● Follow Steps 3 and 4 on p. 114 to choose
images.
Erase.
● Press the p button to choose [Erase],
then press the m button.
Choose All Images
Choose [All Images].
● Follow Step 2 on p. 115 to choose [All
Images] and press the m button.
Erase.
● Press the qr buttons to choose [OK] and
press the m button.
117
Organizing Images by Category
(My Category)
You can organize images in categories. You can display the images in a
category in Filtered Playback (p. 106) and process all images at once by
using the functions below.
• “Viewing Slideshows” (p. 107), “Protecting Images” (p. 113), “Erasing All
Images” (p. 115), “Choosing Images for Printing (DPOF)” (p. 128)
Choose ;.
● Press the m button to choose ; in the
FUNC. menu, then press the m button
again.
Make the setting.
● Press the op buttons to choose a
category, then press the m button.
will appear on the screen.
● Once set,
Images are automatically categorized by shooting condition as they are
shot.
: Images with detected faces, or images shot in I, F, V modes.
: Images detected as
or
in A mode, or images shot in
U, or O.
: Images shot in H, t, w, S, y, P.
Using the Menu
Choose [My Category].
● Press the n button, choose the 1
tab and [My Category], and press the m
button.
118
Organizing Images by Category (My Category)
Choose a selection method.
● Press the op buttons to choose a
selection method and press the m
button.
● Pressing the n button will restore the
menu screen.
Choosing Images Individually
Choose [Select].
● Follow Step 2 above to choose [Select]
and press the m button.
● Press the qr buttons to choose images.
● Press the op buttons, choose a
category and press the m button.
X Once set,
will appear on the screen.
● Pressing the m button again deselects
the category and
disappears.
● To choose multiple images, repeat the
above operation.
Select Range
Choose [Select Range].
● Follow Step 2 above to choose [Select
Range] and press the m button.
● Follow Steps 3 and 4 on p. 114 to choose
images.
● Press the p button, choose the item and
press the qr buttons to choose a type.
Choose the setting.
● Press the p button to choose [Select] and
press the m button.
If you choose [Deselect] in Step 2, you can deselect all of the images in
the [Select Range] category.
119
Rotating Images
You can change the orientation of an image and save it. Movies with a
resolution of
cannot be rotated.
Choose \.
● Press the m button to choose \ in the
FUNC. menu, then press the m button
again.
Rotate the image.
● Press the qr buttons, the image will
rotate 90° in the chosen direction.
● Press the m button to make the setting.
Using the Menu
Choose [Rotate].
● Press the n button, choose the 1
tab and [Rotate], and press the m button.
Rotate the image.
● Press the qr buttons to choose an
image.
X The image will rotate 90° with each press
of the m button.
● Pressing the n button will restore the
menu screen.
120
Resizing Images
You can resize images to a lower pixel setting and save the resized image
as a separate file.
Choose [Resize].
● Press the n button and choose the
1 tab, then choose [Resize] and press
the m button.
Choose an image.
● Press the qr buttons to choose the
image and press the m button.
Choose an image size.
● Press the qr buttons to choose an
option, then press the m button.
X The [Save new image?] screen will
appear.
Save the new image.
● Press the qr buttons to choose [OK] and
press the m button.
X The image will be saved as a new file.
Display the new image.
● When you press the n button, the
[Display new image?] screen will appear.
● Press the qr buttons to choose [Yes] and
press the m button.
X The saved image will display.
• You cannot resize an image to a larger size.
• You cannot resize images taken with the
and
settings.
121
Trimming
You can cut out a portion of a recorded image and save it as a new image file.
Choose [Trimming].
● Press the n button, choose the 1
tab and [Trimming], then press the m
button.
Choose an image.
● Press the qr buttons to choose the
image and press the m button.
Trimming Area
Adjust the trimming area.
X A frame will appear around the portion of
the image to be trimmed.
X The original image will display in the upper
Trimming Area Display
Recorded pixels
after trimming
left and the trimmed image will display in
the lower right.
● If you move the zoom lever to the left or
right, you can change the frame size.
● If you press the opqr buttons, you can
move the frame.
● If you press the l button, you can
change the frame size.
● In an image with detected faces, gray
frames appear around the faces located in
the upper left image. The frames can be
used for trimming. You can switch between
frames by pressing the m button.
● Press the n button.
Save as a new image and display.
● Perform Steps 4 and 5 on p. 121.
•
,
, and
images cannot be trimmed.
• The width and height ratio of an image that can be changed is fixed at
4:3 (for a vertical image 3:4).
• The number of recorded pixels in a trimmed image will be smaller than
before trimming.
122
Adding Effects with the My Colors
Function
You can change the color of an image and save it as a separate image.
Refer to p. 74 for details on each menu item.
Choose [My Colors].
● Press the n button, choose the 1
tab and [My Colors], and press the m
button.
Choose an image.
● Press the qr buttons to choose the
image and press the m button.
Choose a menu option.
● Press the qr buttons to choose an
option.
● You can magnify the image by following
the operations in “Magnifying Images”
(p. 110).
● If you press the m button during
magnified display, you can switch to the
original image. Pressing the n button
restores the menu screen.
● Press the m button.
Save as a new image and display.
● Perform Steps 4 and 5 on p. 121.
• If you repeatedly change the color of an image, the quality will gradually
deteriorate and you may not achieve the expected color.
• The coloration of images changed with this function may vary from those
recorded with the My Colors function (p. 74).
123
Correcting the Brightness (i-Contrast)
The camera can detect areas in an image, such as faces or backgrounds,
that are too dark and automatically adjust them to the optimum brightness.
Also, when the overall image is lacking in contrast, the camera will
automatically correct the image for a sharper impression.
You can choose from four levels of correction: [Auto], [Low], [Medium] or
[High]. The corrected image is saved as a separate file.
Choose [i-Contrast].
● Press the n button, choose the 1
tab and [i-Contrast], then press the m
button.
Choose an image.
● Press the qr buttons to choose the
image and press the m button.
Choose a menu item.
● Press the qr buttons to choose an
option, then press the m button.
Save as a new image and display.
● Perform Steps 4 and 5 on p. 121.
What if the image wasn’t corrected by the [Auto] option as
well as you would like?
Choose [Low], [Medium] or [High] and adjust the image.
• Under some conditions, the image may appear coarse or the exposure
setting may not be suitable.
• Repeatedly adjusting the same image may cause the quality to
deteriorate.
124
Correcting the Red-Eye Effect
You can automatically correct red eyes in images and save them as new
files.
Choose [Red-Eye Correction].
● Press the n button, choose the 1
tab and [Red-Eye Correction], then press
the m button.
X The [Red-Eye Correction] screen will
appear.
Choose an image.
● Press the qr buttons to choose an
image.
Correct the image.
● Press the m button.
X Red-eye detected by the camera will be
corrected and a frame will appear around
the corrected portion.
● You can zoom the image using the
procedures in “Magnifying Images”
(p. 110).
Save as a new image and display.
● Press the opqr buttons to choose
[New File], and press the m button.
X The image will be saved as a new file.
● Perform Step 5 on p. 121.
• Some images may not be properly corrected.
• When [Overwrite] in Step 4 is chosen, the uncorrected image is
overwritten with the corrected data, erasing the original image.
• Protected images cannot be overwritten.
125
Printing from the Print List (DPOF)
You can add images to the print list (DPOF) directly after shooting or while in
playback with the FUNC. menu. You can print from a print list simply by
connecting your camera and printer. These selection methods comply with
the DPOF (Digital Print Order Format) standards.
Easily Add Images to the Print List
Choose an image.
● Press the qr buttons to choose the image.
Choose c (videos will be
excluded).
● Press the m button to choose c in the
FUNC. menu, then press the m button
again.
Print list.
● Press the op buttons and choose the
number of prints, press the qr buttons to
choose [Add] and press the m button.
● To cancel adding images, choose the
added images and press the m button.
Choose c from the FUNC. menu, then
press the qr buttons to choose [Remove]
and press the m button.
126
Printing from the Print List (DPOF)
Print Added Images
The following examples use the Canon SELPHY series printers. Please also
refer to the Personal Printing Guide.
Number of copies to print
Connect the camera to the printer
(p. 29).
Print.
● Press the op buttons, choose [Print
now] and press the m button.
X Printing will start.
● If you stop the printer during printing and
start again, it will start from the next print.
127
Choosing Images for Printing (DPOF)
You can choose certain images on a memory card for printing (up to 998
images) and specify the number of print copies so they can be printed
together or processed at a photo developer service. You can then print all
the chosen images at once or take the memory card to a photo developer to
order prints. These selection methods comply with the DPOF (Digital Print
Order Format) standards.
Print Settings
You can set the print type, date and file number. These settings apply to all
images chosen for printing.
Choose [Print Settings].
● Press the n button and choose the
2 tab, then choose [Print Settings] and
press the m button.
Adjust the settings.
● Press the op buttons to choose a menu
item, then press the qr buttons to choose
an option.
X Pressing the n button accepts the
settings and restores the menu screen.
Print Type
Date
File No.
Clear DPOF data
Standard
Index
Both
On
Off
On
Off
On
Off
Prints one image per page.
Prints several reduced size images per page.
Prints both standard and index formats.
Prints the date from the shooting information.
–
Prints the file number.
–
Removes all print settings after printing.
–
• Some printers or photo developer services may not be able to reflect all
of the print settings in the output.
•
may appear when using a memory card with print settings set by a
different camera. These settings will be overwritten with those set by
your camera.
• Images with the date embedded always print with the date, regardless of
the [Date] setting. As a result, some printers may print the date twice on
these images if [Date] is also set to [On].
128
Choosing Images for Printing (DPOF)
• With [Index] chosen, the [Date] and [File No.] options cannot be set to
[On] at the same time.
• The date will be printed in the style set in the [Date/Time] function in the
3 tab (p. 19).
Choosing the Number of Copies
Choose [Select Images & Qty.].
● Press the n button and choose the
2 tab, then choose [Select Images &
Qty.] and press the m button.
Choose an image.
● Press the qr buttons to choose an
image, then press the m button.
X You will be able to set the number of print
copies.
● If you choose [Index],
appears on the
screen. Pressing the m button again will
deselect the image and
will disappear.
Set the number of prints.
● Press the op buttons to set the number
of prints (maximum 99).
● Repeat Steps 2 and 3 to choose other
images and the number of prints for each.
● You cannot set the number of print copies
for index prints. You can only choose
which images to print.
● Pressing the n button accepts the
settings and restores the menu screen.
129
Choosing Images for Printing (DPOF)
Choose Range
Choose [Select Range].
● Choose [Select Range] in Step 1 on
p. 129 and press the m button.
● Choose images according to Steps 3 and
4 on p. 114.
Make print settings.
● Press the op buttons, choose [Order]
and press the m button.
Set All Images to Print Once
Choose [Select All Images].
● Choose [Select All Images] in Step 1 on
p. 129 and press the m button.
Make print settings.
● Press the qr buttons to choose [OK] and
press the m button.
Clearing All Selections
Choose [Clear All Selections].
● Choose [Clear All Selections] in Step 1 on
p. 129, and press the m button.
All selections will be cleared.
● Press the qr buttons to choose [OK],
then press the m button.
130
8
Customizing the Camera
You can customize various functions to suit your shooting
preferences. The first part of this chapter explains convenient and
commonly used functions. The latter part explains how to change
shooting and playback settings to suit your purposes.
131
Changing Functions
You can customize convenient and commonly used functions from the 3
tab (p. 48).
Turning off Hints & Tips
When you choose an item in the FUNC. menu (p. 47) or MENU (p. 48), a
description of the function (hints and tips) is displayed. You can turn off this
function.
● Choose [Hints & Tips], then press the qr
buttons to choose [Off].
Changing the File Number Assignment
Images you shoot are automatically assigned file numbers in the order they
were taken, from 0001 – 9999, and saved to folders of up to 2,000 images.
You can change the file number assignment.
● Choose [File Numbering], then press the qr
buttons to choose an option.
Continuous
Even if you shoot using a new memory
card, the file numbers are assigned
consecutively until an image with the
number 9999 is taken/saved.
Auto Reset
If you replace the memory card with a
new one, file numbering begins with
0001 again.
• If you use a memory card already containing images, the newly
assigned file numbers may continue the existing numbering for both the
[Continuous] and [Auto Reset] settings. If you want to start over with file
number 0001, format the memory card before use (p. 52).
• Refer to the Software Guide for information regarding folder structure or
image types.
132
Changing Functions
Creating Folders by Shooting Date
Images are saved into folders created each month, however, you can also
create folders by shooting date.
● Choose [Create Folder], then press qr
buttons to choose [Daily].
● Images will be saved into folders created on
each shooting date.
Changing the Lens Retract Time
For safety reasons, the lens retracts about 1 minute after pressing the 1
button when in a Shooting mode (p. 27). You can set the retraction time to
[0 sec.].
● Choose [Lens Retract], then press the qr
buttons to choose [0 sec.].
133
Changing Functions
Turning off the Power Saving Function
You can set the power saving function (p. 53) to [Off]. Setting it to [On] is
recommended to save battery power.
● Choose [Power Saving], then press the m
button.
● Press the op buttons to choose [Auto Power
Down], then use the qr buttons to choose
[Off].
● If you set the power saving function to [Off], be
careful not to forget to turn off the camera after
use.
Setting the Screen Shut-Off Time
You can adjust the time the screen takes to shut off automatically (p. 53).
This also works when [Auto Power Down] is set to [Off].
● Choose [Power Saving], then press the m
button.
● Press the op buttons to choose [Display
Off], then use the qr buttons to choose a
time.
● In order to save battery power, it is
recommended to choose less than [1 min.].
134
Changing Functions
Using the World Clock
When traveling abroad, you can record images with local dates and times simply
by switching the time zone setting if you pre-register the destination time zones.
You can enjoy the convenience of not having to switch the Date/Time settings.
Set the home time zone.
● Choose [Time Zone] and press the m
button.
● When setting this for the first time, check
the information that displays on the screen
at the left, and press the m button.
● Press the qr buttons to choose the home
time zone, then press the m button. To
set daylight saving time (adds 1 hour),
press the op buttons to choose
.
Set the world time zone.
● Press the op buttons to choose
,
then press the m button.
● Press the qr buttons to choose the
destination time zone, then press the m
button.
● You can also set the daylight saving time
as in Step 1.
Choose the world time zone.
● Press the op buttons to choose [Home/
World].
● Press the qr buttons to choose
, then
press the n button.
●
will appear in the [Time Zone] or
shooting screen (p. 44).
If you change the date or time in the
and date will automatically change.
setting, (p. 19), your
time
135
Changing Shooting Functions
If you set the mode switch to 4, and the mode to G, you can change the
settings in the 4 tab (p. 48).
Before attempting to shoot using a function explained in this chapter in
modes other than G mode, check if the function is available in those
modes (pp. 148 – 151).
Turning off the AF Assist Beam
The lamp will automatically light to assist focusing in low light conditions
when you press the shutter button halfway. You can turn off the lamp.
● Choose [AF-assist Beam], then press the
qr buttons to choose [Off].
Turning off the Red-Eye Reduction Function
The red-eye reduction lamp lights in order to reduce the red-eye effect that
occurs when shooting in dark conditions with the flash. You can turn off this
function.
● Choose [Flash Settings], then press the m
button.
● Press the op buttons to choose [Red-Eye
Lamp], then press the qr buttons to choose
[Off].
136
Changing Shooting Functions
Changing the Image Display Time
You can change the length of time the images display directly after shooting.
● Choose [Review], then press the qr buttons
to choose an option.
2 – 10 sec.
Displays images for the set time.
Hold
The image displays until you press the
shutter button halfway.
Off
No image displays
Changing the Way the Image Displays Right
After Shooting
You can change the way the image displays after shooting.
● Choose [Review Info], then press the qr
buttons to choose an option.
Off
Only displays the image taken.
Detailed
Displays detailed information (p. 45).
Focus Check
The area inside the AF frame is
magnified, allowing you to check the
focus. The procedure is the same as in
“Checking the Focus” (p. 109).
137
Changing Shooting Functions
Displaying the Overlay
You can display gridlines for vertical and horizontal guidance, or a 3:2 guide
to confirm the printable area for postcard size prints.
● Choose [Disp. Overlay], then press the qr
buttons to choose an option.
Grid Lines
A grid overlays the display.
3:2 Guide
The areas outside the 3:2 range are
grayed out. This area will not print
when printing on paper with a 3:2
aspect ratio.
Both
Both grid lines, and the 3:2 guide will
display.
• In
mode, you cannot set [3:2 Guide] or [Both].
• Grid Lines will not be recorded on the image.
• The gray areas displayed with [3:2 Guide] are the areas that will not be
printed. The actual image recorded will include the portion in the gray areas.
Changing the IS-Mode Settings
● Choose [IS Mode], then press the qr buttons
to choose an option.
Continuous
Image stabilization is always on. You can
confirm the result directly on the display,
which makes it easier to check the
composition or focus.
Shoot Only
Image stabilization is only active at the
moment of shooting.
Panning
Image stabilization only counters up and
down motion. This option is
recommended for shooting objects
moving horizontally.
• If camera shake is too strong, attach the camera to a tripod. It is
recommended to set the IS Mode to [Off] when the camera is attached
to a tripod.
• When using [Panning], hold the camera horizontally. Image stabilization
does not work when the camera is held vertically.
138
Changing Playback Functions
You can adjust the settings in the 1 tab by pressing the 1 button (p. 48).
Choosing the Image that First Displays
in Playback
● Choose [Resume], then press the qr buttons
to choose an option.
Last seen
Resumes with the image last viewed.
Last shot
Resumes with the most recently shot
image.
Changing the Start-up Image or Sound
In the 3 tab, you can set one of your recorded images as the start-up image
when the camera power is turned on, or change the sounds played for each
camera operation with your recorded sounds.
Change Sounds
● Choose [Sound Options], then press the m
button.
● Press the op buttons to choose an option.
● Press the qr buttons to choose a setting.
1
Preset sounds.
2
You can register your sounds using the supplied
software (p. 140).
Changing the Start-up Screen
● Choose [Start-up Image], then press the m
button.
● Press the qr buttons to choose a setting.
No start-up image.
1
Preset images.
2
You can register your images.
139
Changing the Start-up Image or Sound
Registering the Start-up Screen
When you press the 1 button and set the camera to Playback mode, you
can register sounds and images.
● Choose [Start-up Image], then press the m
button.
● Press the qr buttons to choose [2], then
press the m button.
● Press the qr buttons to choose an image,
then press the m button.
● Press the qr buttons to choose [OK], then
press the m button to complete registration.
Register images or sounds saved on a computer
You can register images or sounds to the camera using the included software.
Refer to the Software Guide for details.
Any previously registered start-up image will be overwritten when
registering a new start-up image.
140
9
Useful Information
This chapter introduces how to use the AC adapter kit (sold
separately), troubleshooting tips and contains lists of functions.
The index also appears at the end.
141
Using Household Power
If you use AC Adapter Kit ACK-DC10 (sold separately), you can use the
camera without worrying about how much charge is left in the battery.
Insert the coupler.
● Open the cover (p. 16) and insert the
coupler as shown until it locks into place
with a click.
● Close the cover (p. 16).
Plug the cord into the coupler.
● Open the cover and fully insert the plug
into the coupler.
Connect the power cord.
● Connect the power cord to the compact
power adapter, then plug the other end
into a power outlet.
● You can turn the camera on to use it.
● After you finish, turn off the camera and
unplug the power cord from the power outlet.
Do not unplug the plug and power cord with the camera turned on. This
could erase images you have taken or damage the camera.
142
Troubleshooting
If you think there is a problem with the camera, first check the following. If
the items below do not solve your problem, contact a Canon Customer
Support Help Desk as listed on the included customer support list.
Power
You pressed the ON/OFF button, but nothing happened.
• Confirm that the battery is properly inserted (p. 16).
• Confirm that the memory card/battery cover is securely closed (p. 16).
• If the battery terminals are dirty, battery performance will decrease. Clean the
terminals with a cotton swab and re-insert the battery several times.
Battery is consumed quickly.
• Battery performance decreases at low temperatures. Warm the battery such as
by placing it in your pocket with the terminal cover on.
Lens will not retract.
• Do not open the memory card/battery cover while the power is on. After closing
the memory card/battery cover, turn the power on then back off (p. 16).
TV output
Image is distorted or not showing on TV (p. 111).
Shooting
Cannot shoot.
• When in Playback mode (p. 27), press the shutter button halfway (p. 23).
Screen does not display properly in dark places (p. 46).
Screen does not display properly while shooting.
Please note, the following will not be recorded in still images, but will be recorded
in movies.
• When the camera is subjected to powerful light sources, the display may darken.
• Under fluorescent lighting, the screen may flicker.
• When shooting bright light sources, a bar of light (purplish red) may appear on
the screen.
h appears on the screen and the shot cannot be taken even though the
shutter button was pressed fully (p. 26).
appears when the shutter button was pressed halfway (p. 59).
•
•
•
•
Set the [IS mode] to [Continuous] (p. 138).
Set the flash to h (p. 67).
Increase the ISO speed (p. 71).
Attach the camera to a tripod.
143
Troubleshooting
Image is blurred.
• Press the shutter button halfway to focus on the subject, then press fully to
shoot (p. 23).
• Shoot the subject within the focusing distance (p. 155).
• Set the [AF-assist Beam] to [On] (p. 136).
• Confirm that functions which you do not intend to use (macro, etc.) are not set.
• Shoot using the focus lock or AF lock (pp. 77, 82).
Even when you press the shutter button halfway, the AF frame does
not appear, and the camera does not focus.
• If you center on the light and dark contrasting area of the subject and push the
shutter button halfway, or repeatedly push the shutter button halfway, the frame
will appear and the camera will focus.
Subject is too dark.
•
•
•
•
Set the flash to h (p. 67).
Adjust the brightness with exposure compensation (p. 66).
Adjust the brightness with the i-Contrast function (pp. 87, 124).
Use the AE lock, or spot metering to shoot (p. 85).
Subject is too bright (overexposed).
•
•
•
•
Set the flash to ! (p. 59).
Adjust the brightness with exposure compensation (p. 66).
Use the AE lock, or spot metering to shoot (p. 85).
Reduce the light illuminating the subject.
Image is dark even though the flash fired (p. 26).
• Increase the ISO speed (p. 71).
• Shoot within an appropriate distance for flash photography (p. 67).
Image taken using the flash is too bright (overexposed).
• Shoot within an appropriate distance for flash photography (p. 67).
• Set the flash to ! (p. 59).
White dots appear on the image when shooting with the flash.
• Light from the flash has reflected off dust particles or other objects in the air.
Image appears rough or grainy.
• Shoot with the ISO speed on a lower setting (p. 71).
• Depending on the Shooting mode, when shooting in a high ISO speed the image
may appear rough or grainy (p. 58).
Eyes appear red (p. 88).
• Set the [Red-Eye Lamp] to [On] (p. 136). When shooting with the flash, the lamp
(on the front of the camera) lights (p. 42), and for approximately 1 second while
the camera is reducing red-eye, it is not possible to shoot. It is more effective if
the subject is looking directly at the lamp. Even better results can be obtained by
increasing the lighting in indoor settings or approaching closer to the subject.
144
Troubleshooting
Recording images to the memory card takes a long time, or continuous
shooting slows down.
• Perform a low-level format of the memory card in the camera (p. 52)
When you can’t make settings for shooting functions or FUNC. menu.
• The items in which settings can be made differ depending on the shooting
mode. Refer to “Functions Available in Each Shooting Mode” (p. 148).
Shooting movies
Correct shooting time does not display, or stops.
• Format the memory card in the camera, or use a memory card capable of
recording at high speeds. Even when the shooting time does not display
properly, the recorded video will be the length that it was actually shot (p. 32).
appeared on the LCD monitor, and shooting ended automatically.
The camera’s internal memory was insufficient. Try one of the following.
• Perform a low-level format of the memory card in the camera (p. 52).
• Change the compression ratio (p. 97).
• Use a memory card capable of recording at high speeds.
Zoom does not operate.
• You can use the digital zoom while recording, but not the optical zoom (p. 99).
Playback
Cannot play back images or movies.
• If the file name or folder structure is changed on a computer, you may not be
able to play back images or movies. Refer to the Software Guide for information
regarding folder structure or file names.
Playback stops, or audio cuts out.
• Use a memory card that has been formatted on this camera (p. 52).
• If you copy a movie to a memory card that reads slowly, playback may interrupt
momentarily.
• Depending on its capabilities, the computer may drop frames, or the audio may
cut out, when playing movies.
Computer
Cannot transfer images to a computer.
The problem may be solved by performing the following operations to slow down
transfer speed when the camera is connected to a computer by a cable.
• Press and hold down the n button, then press the o and m buttons
simultaneously. Choose [B] when it appears on the screen, then press the m
button.
145
List of Messages that Appear on the Screen
If error messages appear on the LCD monitor, try one of the following
solutions.
No memory card
• The memory card is not installed in the correct direction. Install the memory card
in the correct direction (p. 16).
Card locked!
• The SD memory card or SDHC memory card’s write protect tab is set to “LOCK”.
Unlock the write protect tab (p. 18).
Cannot record!
• You attempted to shoot an image without the a memory card, or with a memory
card installed incorrectly. Install the memory card in the correct direction when
shooting (p. 16).
Memory card error (p. 52)
• Contact your Canon Customer Support Help Desk as there may be a problem
with the camera.
Memory card full
• There is not enough free space on the memory card to shoot (pp. 24, 55, 65, 79)
or edit images (pp. 121 – 125). Erase the images (pp. 28, 115) to open space for
new images, or insert an empty memory card (p. 16).
Change the battery pack. (p. 16)
No Image.
• There are no images recorded on the memory card that can be displayed.
Protected! (p. 113)
Unidentified Image/Incompatible JPEG/Image too large./Cannot play
back AVI/RAW
• Unsupported images or data, or corrupted image data cannot be displayed.
• Images manipulated on a computer, that have had their file name changed, or
have been taken with a different camera may not display.
Cannot magnify!/Cannot rotate/Cannot modify image/Cannot register
this image!/Cannot modify/Cannot assign to category
• Incompatible images cannot be magnified (p. 110), rotated (p. 120), edited
(pp. 121 – 125), registered to the start-up screen (p. 140), categorized (p. 118),
or added to a print list (p. 128).
• Images manipulated on a computer, that have had their file name changed, or
have been taken with a different camera may not be magnified, rotated, edited,
registered to the start-up screen, categorized, or added to a print list.
• Movies cannot be magnified (p. 110), edited (pp. 121 – 125), added to a print list
(p. 126), or registered to the start-up screen (p. 139).
146
List of Messages that Appear on the Screen
Cannot select!
• When choosing the selection range (pp. 117, 113, 119), you tried to choose a
starting image that was after the last image or you tried to choose an ending
image that was before the starting image.
• You tried to choose more than 501 images in the selection range (pp. 117, 113,
119).
Too many marks.
• You chose more than 998 images in print settings. Choose less than 998
images (p. 128).
Cannot complete!
• Print settings could not be saved correctly. Reduce the number of selected
images and try again (p. 128).
Naming error!
• The file name could not be created because there is an image with the same
name as the folder that the camera is attempting to create, or the highest
possible file number has already been reached (p. 133). In the 3 menu, change
[File Numbering] to [Auto Reset] (p. 132) or format the memory card (p. 52).
Communication error
• Images could not be transferred to the computer or printed due to the large
amount of images (approx. 1,000) stored on the memory card. Use a
commercially available USB card reader to transfer the images. Insert the
memory card into the printer's card slot to print.
Lens error, restart camera
• A lens error was detected. Press the ON/OFF button to turn the camera off and
back on (p. 42). If this error message continues to appear, contact your Canon
Customer Support Help Desk as there may be a problem with the lens.
• This error can occur if you hold the lens while it is in motion or when using it in a
location with excessive dust or sand in the air.
Exx (xx: number)
• A camera error was detected. Press the ON/OFF button to turn the camera off
and back on (p. 42).
• If an error code appears directly after taking a picture, the shot may not have
been recorded. Check image in Playback mode.
• If this error code reappears, note the number and contact your Canon Customer
Support Help Desk as there may be a problem with the camera.
147
Functions Available in Each Shooting Mode
Shooting modes
A
4
{
—
—
{
{
—
—
—
—
{
{
{
{
—
—
{
{
{
G
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
I
{
{
—
{
—
{
{
{
{
{
{
{
{
—
—
{
{
{
F
*1
*1
—
{
—
{
{
{
{
{
{
{
{
—
—
{
{
{
V
{
{
—
{
—
{
—
—
{
{
{
{
{
—
—
{
{
{
Light Metering (p. 84)
{
—
{
{
{
—
{
—
{
—
My Colors (p. 74)
—
{
—
—
—
{
—
{
—
{
—
{
{
{
{
{
{
{
—
{
—
{
{
{
—
{
—
{
{
{
—
{
—
{
{
Compression Ratio (Image Quality)
(p. 69)
{
{
{
{
{
Recording Pixels (p. 69, 97)
{
—
{
—
{
—
{
—
{
—
Function
h
Flash (pp. 59, 67, 86)
!
All Range
Focusing Zone (pp. 67, 68)
e
u
Exposure Compensation (p. 66)/Exposure Shift (p. 98)
Ò Î
"
$ *2
Self-Timer (pp. 63, 64, 75, 76)
AF Lock (p. 82)
AE Lock (pp. 85, 98)/FE Lock (p. 85)
TV Display (p. 77)
Information Display (p. 44)
On
Off
Func. Menu
White Balance (p. 72)
ISO Speed (p. 71)
Drive Mode (p. 73)
W
*1 Set to
when flash fires.
*2 Possible settings: 0 – 30 seconds in [Delay], and 1 – 10 shots in [Shots].
*3 ISO 3200 (p. 58) is set by default. *4 Fixed to
. *5
is not selectable.
148
Functions Available in Each Shooting Mode
4
E
H
{
{
—
{
—
{
{
{
{
{
{
{
{
—
—
{
{
{
U
*1
*1
—
{
—
{
—
—
{
{
{
{
{
—
—
{
{
{
t
—
—
—
{
—
{
—
—
{
{
{
—
{
—
—
{
{
{
≈
—
*1
—
{
—
{
{
{
—
{
{
{
{
{
—
{
{
{
w
{
{
—
{
—
{
{
{
{
{
{
{
{
—
—
{
{
{
S
{
{
—
{
—
{
{
{
{
{
{
{
{
—
—
{
{
{
y
—
{
—
{
—
{
{
{
{
{
{
{
{
—
—
{
{
{
O
{
{
—
{
—
{
{
{
{
{
{
{
{
—
—
{
{
{
P
{
{
—
{
—
{
{
{
{
{
{
{
{
—
—
{
{
{
Z
—
—
—
{
—
{
{
{
—
{
{
{
{
—
—
{
{
{
R
—
—
—
{
—
—
{
—
{
{
{
{
{
{
{
{
{
{
{
—
{
—
{
—
{
—
{
—
{
—
{
—
{
—
{
—
{
—
{
{
{
—
—
—
—
{
—
—
—
—
—
—
{
—
{
—
{
—
{
{
{
—
{
—
{
{
{
—
{
—
{
{
{
{
—
{
{
{
{
—
{
—
{
{
{
—
{
—
{
{
{
—
{
—
{
{
{
—
{
—
{
{
{
—
{
—
{
{
{
—
{
{
{
{
{
{
{
{
{
—
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
*4
*5
—
—
{
—
{
—
{
—
{
—
{
—
{
—
{
—
{
—
{
—
*3
TY vx
{
—
{
{
—
{
{
{
—
—
{
{
{
{
{
{
—
{
{
{
{
{
—
—
—
—
—
—
—
—
{
—
{
{
—
—
E
—
—
—
—
—
{
{
{
{
{
{
—
—
{
{
{
{
{
>z
—
—
—
—
—
{
{
{
—
{
{
—
—
—
—
{
{
—
{
—
{
—
{
{
—
{
{
{
—
{
—
{
{
{
—
—
—
{
—
{
—
—
—
{
—
—
*5
—
{
—
{
{
—
—
{ Selectable, or set automatically. — Not selectable
149
Menus
4 Shooting Menu
Shooting modes
A
4
F
V
Face AiAF
{
{
{
{
{
Center
—
{
{
{
{
Normal/Small
—
{
—
—
—
Standard/Off
{
{
{
{
{
Digital Tele-converter (1.5x/2.0x)
{
{
{
{
{
AF-Point Zoom (p. 81)
On/Off
{
{
{
{
{
Servo AF (p. 83)
On/Off
*3
{
{
{
{
AF-assist Beam (p. 136)
On/Off
{
{
{
{
{
{
Function
AF Frame (p. 80)
AF Frame Size (p. 80)
Digital Zoom (p. 60)
Flash Settings (p. 88)
i-Contrast (p. 87)
G
I
Red-Eye Corr.
On/Off
{
{
{
{
Red-Eye Lamp
On/Off
{
{
{
{
{
*2
{
—
—
—
Off/Auto
Review (p. 137)
Off/2 – 10 sec./Hold
{
{
{
{
{
Review Info (p. 137)
Off/Detailed/Focus Check
{
{
{
{
{
Blink Detection (p. 89)
On/Off
{
{
{
{
{
Off/Grid Lines
{
{
{
{
{
3:2 Guide/Both
{
{
{
{
{
Continuous/Off
*2
{
{
{
{
Shoot Only/Panning
—
{
{
{
{
Off/Date/Date & Time
{
{
{
{
{
Disp. Overlay (p. 138)
IS Mode (p. 138)
Date Stamp (p. 62)
*1 AiAF
*2 Always [On].
*3 [On] when movement is detected.
*4 Available when h is chosen.
150
Menus
4
E
H
U
t
≈
w
S
y
O
P
Z
R
TY vx
E
{
{
—
{
{
{
{
{
{
{
{
{
—
*1
>z
*1
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
{
{
{
{
{
{
{
{
{
—
*2
—
—
{
—
{
{
{
{
{
{
{
{
{
—
—
—
—
—
—
{
{
{
{
{
{
{
{
{
{
—
{
—
—
—
{
{
—
{
{
{
{
{
{
{
{
{
—
—
—
{
{
—
{
{
{
*4
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
—
—
—
—
—
—
{
{
—
{
{
{
{
{
{
—
—
{
{
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
{
{
{
{
{
{
{
{
{
{
{
{
—
—
—
{
{
—
—
{
—
{
{
{
—
{
{
—
—
—
{
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
{
{
{
{
{
{
{
{
{
—
{
{
—
—
—
{ Selectable, or set automatically. — Not selectable
151
Menus
3 Set up Menu
Item
Options/Summary
Ref. Page
Mute
On/Off*
Volume
Set all operation sounds (5 levels).
p. 49
Sound Options
Set the sounds for each camera operation.
p. 139
Hints & Tips
On*/Off
p. 132
LCD Brightness
Set within a range of ±2.
p. 50
Start-up Image
Add an image as start-up image.
p. 139
p. 49
Format
Formats memory card, erasing all data
p. 52
File Numbering
Continuous*/Auto Reset
p. 132
Create Folder
Monthly*/Daily
p. 133
Lens Retract
1 min.*/0 sec.
p. 133
Power Saving
Auto Power Down: On*/Off
Display Off: 10, 20 or 30 sec./1*, 2 or 3 min.
Time Zone
Home/World
Date/Time
Date and time settings
p. 20
Video System
NTSC/PAL
p. 111
Language
Choose display language.
p. 21
Reset All
Returns camera to default settings.
p. 51
* Default setting
152
p. 53 , 134
p. 135
Menus
1 Playback Menu
Item
Options/Summary
Ref. Page
Slideshow
Plays back images automatically.
p. 107
Erase
Erases images.
p. 115
Protect
Protects images.
p. 113
Rotate
Rotates images.
p. 120
My Category
Categorizes images.
p. 118
i-Contrast
Corrects dark portions and contrast in still
images.
p. 124
Red-Eye Correction
Corrects red eyes in still images.
p. 125
Trimming
Trims portions of still images.
p. 122
Resize
Resizes and saves still images.
p. 121
My Colors
Adjusts colors in still images.
p. 123
Scroll Display
On*/Off
p. 105
Resume
Last seen*/Last shot
p. 139
Transition
Fade*/Scroll/Slide/Off
p. 110
* Default setting
2 Print Menu
Item
Options/Summary
Ref. Page
Print
Displays printing screen.
p. 29
Select Images & Qty.
Chooses individual images for printing.
p. 129
Select Range
Chooses starting and ending images for printing.
p. 130
Select All Images
Chooses all images for printing.
p. 130
Clear All Selections
Cancels all settings for printing.
p. 130
Print Settings
Sets the printing style.
p. 128
153
Handling Precautions
• This camera is a high-precision electronic device. Do not drop it or subject
it to strong impacts.
• Never place the camera close to magnets or motors that generate strong
electromagnetic fields. Exposure to strong magnetic fields may cause
malfunctions or corrupt image data.
• If water droplets have fallen onto, or dirt is stuck on the camera or LCD
monitor, wipe with a dry soft cloth or eyeglass wiper. Do not rub or apply
force.
• Never use cleaners containing organic solvents to wipe the camera or
LCD monitor.
• Use a commercially available blower brush to remove dust from the lens.
For stubborn dirt contact the closest Canon Customer Support Help Desk
as listed in your Warranty System Booklet.
• When you move the camera rapidly from cold to hot temperatures,
condensation may form on the internal or external surfaces of the camera.
To avoid condensation, put the camera in an airtight, resealable plastic
bag and let it adjust to temperature changes slowly before removing it
from the bag.
• If condensation has formed, stop using the camera immediately.
Continued use may damage the camera. Remove the battery and
memory card, and wait until the moisture has completely evaporated
before resuming use.
154
Specifications
Camera Effective Pixels. . . . . . . . . . . Approx. 12.1 million
Image Sensor . . . . . . . . . . . . . . . . . . 1/2.3-inch type CCD (Total number of pixels:
Approx. 12.4 million)
Lens . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 (W) – 20.0 (T) mm
35mm film equivalent: 28 (W) – 112 (T) mm
f/2.8 (W) – f/5.9 (T)
Digital Zoom. . . . . . . . . . . . . . . . . . . . Approx. 4.0x (Up to approx. 16x in combination
with the optical zoom)
LCD Monitor. . . . . . . . . . . . . . . . . . . . 2.7-inch type TFT color LCD monitor
Approx. 230,000 dots, Picture coverage 100%
AF Frame Mode. . . . . . . . . . . . . . . . . Face AiAF/Center
Servo AF . . . . . . . . . . . . . . . . . . . . . . On/Off
Focusing Range (from end of lens) . . Auto: 3 cm (1.2 in.) – infinity (W)/
50 cm (1.6 ft.) – infinity (T)
Normal: 30 cm (12 in.) – infinity (W)/
50 cm (1.6 ft.) – infinity (T)
Macro: 3 – 50 cm (1.2 in. – 1.6 ft.) (W)
Infinity: 3 m (9.8 ft.) – infinity
Digital Macro: 3 – 10 cm (1.2 – 3.9 in.)
Kids&Pets: 1 m (3.3 ft.) – infinity
Shutter . . . . . . . . . . . . . . . . . . . . . . . . Mechanical shutter and electronic shutter
Shutter Speed . . . . . . . . . . . . . . . . . . 1 – 1/1500 sec.
15 – 1/1500 sec. (Total shutter speed range)
Image Stabilization . . . . . . . . . . . . . . Lens-shift type
Metering System . . . . . . . . . . . . . . . . Evaluative, Center-weighted average or Spot
Exposure Compensation . . . . . . . . . . ±2 stops in 1/3-stop increments
ISO speed . . . . . . . . . . . . . . . . . . . . . Auto/ISO 80/100/200/400/800/1600
(Standard Output Sensitivity,
Recommended Exposure Index)
White Balance . . . . . . . . . . . . . . . . . . Auto, Day Light, Cloudy, Tungsten, Fluorescent,
Fluorescent H, Custom
Built-in Flash . . . . . . . . . . . . . . . . . . . Auto, On, Slow Synchro, Off
* Red-eye reduction/Red-eye correction/FE Lock
settings available
Built-in Flash Range . . . . . . . . . . . . . 30 cm – 4.0 m (12 in. – 13 ft.) (W)/
50 cm – 2.0 m (1.6 – 6.6 ft.) (T)
Shooting Modes. . . . . . . . . . . . . . . . . Shooting Mode: Auto, P, Portrait, Night Snapshot,
Kids&Pets, Indoor, Sunset, Fireworks,
Long Shutter, Beach, Underwater, Aquarium,
Foliage, Snow, ISO 3200, Digital Macro, Color
Accent, Color Swap, Stitch Assist
Movie Mode: Standard, Color Accent, Color Swap
Continuous Shooting . . . . . . . . . . . . . Approx. 0.8 images/sec.
Self-timer . . . . . . . . . . . . . . . . . . . . . . Approx. 10-sec./Approx. 2-sec. delay, FaceSelfTimer, Custom Timer
155
Specifications
i-Contrast . . . . . . . . . . . . . . . . . . . . . .Off/Auto
Recording Media . . . . . . . . . . . . . . . .SD memory card, SDHC memory card,
MultiMediaCard, MMCplus card, HC MMCplus
card
File Format. . . . . . . . . . . . . . . . . . . . .Design rule for Camera File system and DPOF
compliant
Data Type . . . . . . . . . . . . . . . . . . . . .Still images: Exif 2.2 (JPEG)
Movies: MOV (Image data: H.264, Audio data:
Linear PCM) (Mono)
Compression . . . . . . . . . . . . . . . . . . .Fine, Normal
Number of Recording Pixels
(Still images) . . . . . . . . . . . . . . . . . . .Large: 4000 x 3000 pixels
Medium 1: 3264 x 2448 pixels
Medium 2: 2592 x 1944 pixels
Medium 3: 1600 x 1200 pixels
Small: 640 x 480 pixels
Widescreen: 4000 x 2248 pixels
(Movies) . . . . . . . . . . . . . . . . . . . . . . .1280 x 720 pixels (30 frames/sec.)
640 x 480 pixels (30 frames/sec.)
320 x 240 pixels (30 frames/sec.)
Number of Possible Shots . . . . . . . . .Approx. 220 images (Based on CIPA standardized
measurement)
Playback Function . . . . . . . . . . . . . . .Single Image, Movie, Magnified Focus, Index,
Magnified, Filtered Playback, Slideshow
Editing Function . . . . . . . . . . . . . . . . .Erase, Protect, My Category, Resize, My Colors,
i-Contrast, Trimming, Rotate, Red-Eye Correction
Direct Print Type . . . . . . . . . . . . . . . .PictBridge capable
Interface . . . . . . . . . . . . . . . . . . . . . . .Hi-Speed USB (Dedicated connector with unified
type of digital, audio and video*)
HDMI (HDMI Mini Connector)
* mini-B compatible
Video/Audio output (NTSC and PAL capable,
mono audio)
Communication Settings . . . . . . . . . .MTP, PTP
Power. . . . . . . . . . . . . . . . . . . . . . . . .Battery Pack NB-4L
(rechargeable lithium-ion battery)
AC adapter kit ACK-DC10
Operating Temperatures . . . . . . . . . .0 – 40 °C (32 – 104 °F)
Operating Humidity . . . . . . . . . . . . . .10 – 90%
Dimensions (excluding protrusions) . .89.5 x 54.9 x 20.0 mm (3.52 x 2.16 x 0.79 in.)
Weight (camera body only) . . . . . . . .Approx. 120 g (4.23 oz.)
156
Specifications
Battery Pack NB-4L
Type. . . . . . . . . . . . . . . . . . . . . . . . . . Rechargeable lithium-ion battery
Voltage. . . . . . . . . . . . . . . . . . . . . . . . 3.7 V DC
Capacity. . . . . . . . . . . . . . . . . . . . . . . 760 mAh
Charging cycles . . . . . . . . . . . . . . . . . Approx. 300 times
Operating temperature. . . . . . . . . . . . 0 – 40 °C (32 – 104 °F)
Dimensions . . . . . . . . . . . . . . . . . . . . 35.4 × 40.3 × 5.9 mm (1.39 × 1.59 × 0.23 in.)
Weight . . . . . . . . . . . . . . . . . . . . . . . . Approx. 17 g (0.60 oz.)
Battery Charger CB-2LV/CB-2LVE
Rated input . . . . . . . . . . . . . . . . . . . . 100 – 240 V AC (50/60 Hz), 0.1 A (100 V) – 0.06 A
(240 V)
Rated output . . . . . . . . . . . . . . . . . . . 4.2 V DC, 0.65 A
Charge time . . . . . . . . . . . . . . . . . . . . Approx. 1 hour 30 min.
Operating temperature. . . . . . . . . . . . 0 – 40 °C (32 – 104 °F)
Dimensions . . . . . . . . . . . . . . . . . . . . 53.0 × 86.0 × 19.5 mm (2.09 × 3.39 × 0.77 in.)
Weight . . . . . . . . . . . . . . . . . . . . . . . . Approx. 60 g (2.12 oz.) (CB-2LV)
Approx. 55 g (1.94 oz.) (CB-2LVE, excluding
power cord)
• All data is based on tests by Canon.
• Camera specifications or appearance are subject to change without notice.
157
Index
Numerics
3:2 Guide................................................. 138
A
AC Adapter Kit................................... 40, 142
Accessories ............................................... 38
AE Lock ..................................................... 85
AF J Focus
AF Frame ............................................ 25, 80
AF Lock ..................................................... 82
Aquarium (Scene Mode) ........................... 58
AV Cable ............................................. 2, 111
B
Battery
Battery Charger............................ 2, 14, 40
Charge Indicator .................................... 15
Date/Time Battery .................................. 20
Power Saving......................................... 53
Recharge ............................................... 14
Battery Charger ......................................... 14
Beach (Scene Mode)................................. 57
Black and White Images............................ 74
C
Camera Shake .................................. 59, 138
Clock Function........................................... 54
Color Accent (Scene Mode) ................ 91, 96
Color Swap (Scene Mode) .................. 92, 96
Components Guide ................................... 42
Compression J Image Quality
Continuous Shooting ................................. 73
D
Date and Time
Adding to Image..................................... 62
Changing................................................ 20
Date/Time Battery .................................. 20
Settings .................................................. 19
Date and Time J Date/Time
Default Settings......................................... 51
Deleting J Erasing
DIGITAL CAMERA Solution Disk .......... 2, 35
Digital Macro ............................................. 68
158
Digital Tele-Converter ............................... 61
Digital Zoom .............................................. 60
Display Language...................................... 21
Display Overlay ....................................... 138
DPOF .............................................. 126, 128
E
Editing
i-Contrast ............................................. 124
My Colors............................................. 123
Red-Eye Correction ............................. 125
Resizing (Making Images Smaller) ...... 121
Rotating Images................................... 120
Trimming .............................................. 122
Enlarged Display ..................................... 110
Equipment
Default Settings...................................... 51
Holding the Camera ............................... 13
Erasing All Images .................................. 115
Erasing Images ......................................... 28
Error Messages ....................................... 146
Exposure
AE Lock.................................................. 85
Correction .............................................. 66
FE Lock.................................................. 85
F
Face AiAF.................................................. 80
Face Self-Timer......................................... 64
Factory Settings J Default Settings
FE Lock ..................................................... 85
File Number............................................. 132
Filtered Playback..................................... 106
Fireworks (Scene Mode) ........................... 57
Flash
Off .......................................................... 59
On .......................................................... 67
Supplementary Flash ............................. 40
Focus
AF Frame ............................................... 25
AF Frame Mode ..................................... 80
AF Lock.................................................. 82
AF-Point Zoom....................................... 81
Servo AF ................................................ 83
Index
Focus Check............................................ 109
Focus Lock ................................................ 77
Format J Memory Card, Formatting
Formatting (Memory Card) .................. 22, 52
FUNC. Menu
Basic Operations.................................... 47
List ....................................................... 148
G
Green Leaves/Autumn Foliage
(Scene Mode) ........................................... 58
Grid Lines ................................................ 138
H
High Speed (ISO) ................................ 58, 71
High-Power Flash ...................................... 40
Histogram .................................................. 46
Household Power .................................... 142
I
i-Contrast ........................................... 87, 124
Image Quality (Compression Ratio) .......... 69
Images
Editing J Editing
Erasing Images ...................................... 28
Playback J View
Protect.................................................. 113
Indoor (Scene Mode)................................. 57
Infinity ........................................................ 68
Interface Cable ................................ 2, 29, 35
ISO 3200 (Scene Mode)............................ 58
ISO Speed ................................................. 71
K
Kids&Pets (Scene Mode) .......................... 56
L
Lamp............................................42, 63, 136
LCD monitor J Screen
M
Menu
Basic Operations....................................48
List........................................................150
Metering Mode...........................................84
MMCplus/HC MMCplus Memory Card ......18
Mode Switch ..............................................42
Movie
Editing ..................................................101
Image Quality (Frame Rate)...................97
Mode ......................................................96
Recording Pixels ....................................97
Shooting Time ..................................32, 97
Viewing (Playback).................................33
MultiMediaCard J Memory Card
Mute...........................................................49
My Category ............................................118
My Colors ..........................................74, 123
N
Night Snapshot (Scene Mode) ..................56
Number of Shots........................................15
O
ON/OFF Button..........................................42
P
Panoramic Photos .....................................94
Personal Printing Guide...............................2
PictBridge ..................................................29
Playback J View
Playback Button...................................27, 43
Playback With Transition Effects .............110
Portrait (Scene Mode) ...............................56
Postcard Size ............................................70
Power J Battery
Power Saving ............................................53
Print Settings (DPOF)..............................126
Printer ..................................................29, 30
Printing ......................................................29
Program AE ...............................................66
Protect .....................................................113
Macro......................................................... 67
Memory Cards ..................................... 16, 18
Available Shots ...................................... 18
Formatting ........................................ 22, 52
159
Index
R
T
Recording Pixels (Image Size) .................. 69
Red-Eye
Auto Correction ...................................... 88
Correction ............................................ 125
Reduction............................................. 136
Resizing (Making Images Smaller).......... 121
Rotating Images ...................................... 120
Terminal ............................................ 29, 111
Time Zone ............................................... 135
Tone (White Balance)................................ 72
Transferring Images to a Computer .......... 34
Travel Abroad.................................... 15, 135
Trimming ................................................. 122
Troubleshooting....................................... 143
TV
Shooting Using a TV Monitor ................. 77
Viewing Images on a TV ...................... 111
S
SCN (Scene Mode) ................................... 56
Screen
Display Language .................................. 21
Information Displayed ............................ 44
Menu Operations ............................. 47, 48
Switching the Display....................... 44, 45
Scroll Display........................................... 105
SD/SDHC Memory Card ........................... 18
Self-Timer
10 second Self-Timer............................. 63
Changing Delay and
Number of Shots .................................... 76
Face Self-Timer ..................................... 64
Two Second Self-Timer ......................... 75
Sepia Tones .............................................. 74
Servo AF ................................................... 83
Shooting Date and Time J Date/Time
Shooting Using a TV ................................. 77
Shutter Button ........................................... 23
Slideshow................................................ 107
Snow (Scene Mode).................................. 58
Software
DIGITAL CAMERA Solution Disk....... 2, 35
Software Guide ........................................ 2
Transferring Images to a Computer ....... 34
Sound Settings
Mute ....................................................... 49
Stitch Assist (Scene Mode) ....................... 94
Strap...................................................... 2, 13
Sunset (Scene Mode)................................ 57
Supplementary Flash ................................ 40
160
U
Underwater (Scene Mode) ........................ 57
V
Video J Movies
Viewing (Playback)
Enlarged Display.................................. 110
Images on a TV.................................... 111
Index Display ....................................... 104
Single Image Playback .......................... 27
Slideshow............................................. 107
Viewing Images on a TV ......................... 111
W
White Balance ........................................... 72
Wide (Recording Pixels)...................... 69, 70
World Clock ............................................. 135
Wrist Strap J Strap
Z
Zoom ............................................. 24, 31, 60
Trademark Acknowledgments
• The SDHC logo is a trademark.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
Disclaimer
• Reprinting, transmitting, or storing in a retrieval system any part of this
guide without the permission of Canon is prohibited.
• Canon reserves the right to change the contents of this guide at any
time without prior notice.
• Illustrations and screenshots in this guide may differ slightly from the
actual equipment.
• Every effort has been made to ensure that the information contained in
this guide is accurate and complete. However, if you notice any errors
or omissions, please contact the Canon customer service center
indicated on the customer support list included with the product.
• The above items notwithstanding, Canon accepts no liability for
damages due to mistaken operation of the products.
CEL-SN5TA210
© CANON INC. 2009
Download PDF

advertising