Instruction manual | Canon 1100D Digital Camera User Manual

m
mt
mm.1
mau_
Advanced Shooting
ThischapterbuitdsonChapter3and
waystoshootcreatively.
introducesmore
Thefirsthalfofthischapterexplainshowtousethe<Tv>
<Av> <M> <A-DEP> modes on the Mode Dial.
AllthefunctionsexplainedinChapter3canalsobeusedin
the <Tv>
<Av>
and <M> modes.
ToseewHchfunctionscanbeusedineachshooting
see page232.
The # markshownonthe
rightofthe
pagetitle
thatthefunotion
isavailableonlyinCreativeZone
(p.22).
mode,
indicates
modes
Thepointericon</"_>disp,ayed
togetherwith the shutter speed, aperture
seWng, orexposurecompensation
amount indicates that you can turn the
0
-
,
.
<_>dia,
setting.
toadjusttherespective
::::
Tv" Action Shots
You can either freeze the action or create motion blur with the < Tv >
(Shutter-priority AE) mode on the Mode Dial.
* <Tv> stands for Time value.
Slurred motion
Frozen action
(Slow shutter speed: 1/30 sec.)
(Fast shutter speed: 1/2000 sec.)
Set the Mode Dial to <Tv>.
Set the desired
shutter
speed.
See "Shooting Tips" for advice on
setting the shutter speed.
Turning the <_>
dial to the right
sets a faster shutter speed, and
turning it to the left sets a slower one.
Take the picture.
When you focus and press the
shutter button completely, the picture
will be taken at the selected shutter
speed.
Shutter Speed Display
The LCD monitor displays the shutter speed as a fraction. However, the
viewfinder displays only the denominator. Also, "0"5" indicates 0.5 sec. and
"15"" is 15 sec.
92
Tv: Action Shots
To freeze the action or moving subject.
Use a fast shutter speed such as 1/4000 sec. to 1/500 sec.
To blur a running child or animal giving the impression of fast
movement.
Use a medium shutter speed such as 1/250 sec. to 1/30 sec. Follow
the moving subject through the viewfinder and press the shutter
button to take the picture. If you use a telephoto lens, hold it steady
to prevent camera shake.
How to blur a flowing river or water fountain.
Use a slow shutter speed of 1/30 sec. or slower. Use a tripod to
prevent hand-held camera shake.
Set the shutter speed so that the aperture
blink in the viewfinder.
display
does not
If you press the shutter button halfway and change
the shutter speed while the aperture is displayed,
the aperture display will also change to maintain the
same exposure (amount of light reaching the image
sensor). If you exceed the adjustable aperture
range, the aperture display will blink to indicate that
the standard exposure cannot be obtained.
If the exposure will be too dark, the maximum aperture (smallest
number) will blink. If this happens, turn the < _ > dial to the left to
set a slower shutter speed or increase the ISO speed.
If the exposure will be too bright, the minimum aperture (highest
number) will blink, if this happens, turn the < _ > dial to the right to
set a faster shutter speed or decrease the ISO speed.
To obtain a correct flash exposure, the flash output will be set
automatically (autoflash exposure) to match the automatically-set
aperture. The flash sync speed can be set from 1/200 sec. to 30 sec.
93
Av"
Changing
the Depth of Field
To blur the background or to make everything near and far look sharp,
set the Mode Dial to < Av > (Aperture-priority AE) to adjust the depth of
field (range of acceptable focus).
* < Av > standsfor Aperturevaluewhichisthe sizeof thediaphragmhole insidethe lens.
Blurred background
(With a low aperture f/number:
f/5.6)
Sharp foreground and background
(With a high aperture f/number: f/32)
Set the Mode Dial to <Av>.
Set the desired
aperture.
The higher the f/number, the wider
the depth of field where sharper focus
is obtained in both the foreground
and background.
Turning the <_>
dial to the right will
set a higher f/number (smaller
aperture opening), and turning it to
the left will set a lower f/number
(larger aperture opening).
Take the picture.
Focus and press the shutter button
completely. The picture will be taken
with the selected aperture.
Aperture
Display
The higher the f/number, the smaller the aperture opening will be. The
apertures displayed will differ depending on the lens. If no lens is attached to
the camera, "00" will be displayed for the aperture.
94
Av:Changing
theDepth
ofField
i_,,!_
__,_,_-' _
_ ::_1_i_i,
,_ __,_
_ _,_;_,_,,_,_',_
____:_i_
G,i%,_7,_7,_,_,_
When using an aperture with a high f/number, note that camera
shake can occur in low light scenes.
A higher aperture f/number will make the shutter speed slower.
Under low light, the shutter speed can be as long as 30 sec. In such
cases, increase the ISO speed and hold the camera steady or use a
tripod.
The depth of field depends not only on the aperture, but also on
the lens and on the subject distance.
Since wide-angle lenses have a wide depth of field (range of
acceptable focus in front of and behind the point of focus), you need
not set a high aperture f/number to obtain a sharp picture from the
foreground to the background. On the other hand, a telephoto lens
has a narrow depth of field.
And the closer the subject, the narrower the depth of field. A farther
subject will have a wider depth of field.
Set the aperture
blink.
so that the shutter
speed display
does not
If you press the shutter button halfway and change
the aperture while the shutter speed is displayed,
the shutter speed display will also change to
maintain the same exposure (amount of light
reaching the image sensor). If you exceed the
adjustable shutter speed range, the shutter speed
display will blink to indicate that the standard
exposure cannot be obtained.
If the picture will be too dark, the "30"" (30 sec.) shutter speed
display will blink. If this happens, turn the < _ > dial to the left to set
a lower aperture f/number or increase the ISO speed.
If the picture will be too bright, the "4000" (1/4000 sec.) shutter
speed display will blink. If this happens, turn the < _ > dial to the
right to set a higher aperture f/number or decrease the ISO speed.
95
Av: Changing the Depth of Field
To obtain a correct flash exposure, the flash output wiii be set
automatically to match the set aperture (autoflash exposure). The
shutter speed wiii be set automatically between 1/200 sec. - 30 sec. to
suit the scene's brightness.
in low light, the main subject is exposed with the automatic flash, and
the background is exposed with a slow shutter speed set automatically.
Both the subject and background look properly exposed (automatic
slow-speed flash sync), if you are handholding the camera, keep it
steady to prevent camera shake. Using a tripod is recommended.
If you do not want a slow shutter speed to be used, set [2: Flash sync.
speed in Av mode] to [1:1/200-1/60
sec. auto] or [2:11200 sec.
(fixed)] in [_ Custom Functions (C.Fn)] (p.218).
The aperture opening (diaphragm) changes only at the moment when
the picture is taken. Otherwise, the aperture remains fully open.
Therefore, when you look at the scene through the viewfinder or LCD
monitor, the depth of field wiii look narrow. With the procedure below,
you can check the depth of field before taking the picture.
Enable
depth-of-field
preview
to be used.
Under [_ Custom Functions (C.Fn)], set [8: Assign SET
button] to [5: Depth-of-field
preview] (p.222).
For details about Custom Function settings, see page 216.
Exit the
menu.
Press the < MENU > button two times to exit the menu.
press
The aperture will be stopped down so you can see the depth of field.
While looking at the Live View image (p.122) and holding down the <_)>
button, you can change the aperture and see how the depth of field
changes.
96
M- Manual Exposure
You can set both the shutter speed and aperture manually as desired.
While referring to the exposure level indicator in the viewfinder, you can
set the exposure as desired. This method is called manual exposure.
* <M> stands for Manual.
Set the Mode Dial to <M>.
li
Set the shutter
speed
and
aperture.
To set the shutter speed, turn the
<_>
dial.
<_>
<Avr_>
+ <_>
To set the aperture, hold down the
< Avr_> button and turn the <_>
dial.
Standard
exposure
iodax Focus
the subject.
Press the shutter button halfway.
The exposure setting will be
displayed in the viewfinder.
The exposure level mark <|> indicates
Exposure level mark
how far the current exposure level is
from the standard exposure level.
Set the exposure
picture.
and take the
Set the shutter speed and aperture as
desired.
If the exposure set exceeds +2 stops from
the standard exposure, the end of the
exposure level indicator will display < 4 >
or <)> in the viewfinder. (On the LCD
monitor, if the exposure level is higher
than +3 stops, the <i> icon will blink at
where <-3> or <+3> is displayed.)
_'_ If [131:Auto
Lighting Optimizer]
(p,107) is set to any setting other than
[Disabme], the image may still look bright even if a darker exposure has been set.
97
M: Manual Exposure
To obtain a correct flash exposure, the flash output will be set
automatically (autoflash exposure) to match the manually-set aperture.
The flash sync speed can be set from 1/200 sec. to 30 sec. and bulb.
A bulb exposure keeps the shutter open
for as long as you hold down the shutter
button, it can be used to photograph
fireworks, etc.
in step 2 on the preceding page, turn the
< _ > dial to the left to set <BULB>.
The elapsed exposure time wiii be
displayed on the LCD monitor.
Elapsed exposure time
,
During bulb exposures,
do not point the lens toward the sun. The sun's
heat can damage the camera's internal components.
Since bulb exposures produce more noise than usual, the image might
look a little grainy.
You can reduce the noise due to long exposures by setting [3: Long exp.
noise reduction] to [1: Auto] or [2: On] in the [9_ Custom Functions
(C.Fn)] (p.219).
For bulb exposures,
using a tripod and Remote Switch (sold separately,
p.229) is recommended.
98
A-DEP:Automatic
Depth=of=Field
AE
Objects in the foreground and background will be in focus automatically.
All the AF points will function to detect the subject, and the aperture
required to attain the necessary depth of field will be set automatically.
* <A-DEP>stands for Auto-Depth of field. This mode sets the depth of field
automatically.
Set the Mode Dial to <A-DEP>.
Focus
the subject.
Aim the AF points over the subjects
and press the shutter button halfway
((_4).
All the subjects covered by the AF
points flashing in red will be in focus.
If focus is not achieved, the picture
cannot be taken.
Take the picture.
The aperture display in the viewfinder blinks.
The exposure is correct, but the desired depth of field cannot be
obtained. Either use a wide-angle lens or move farther away from
the subjects.
The shutter speed display in the viewfinder blinks.
If the "30"" shutter speed blinks, it means that the subject is too dark.
Increase the ISO speed. If the "4000" shutter speed blinks, it means
that the subject is too bright. Decrease the ISO speed.
A slow shutter speed has been set.
Use a tripod to steady the camera.
I want to use flash.
Flash can be used, however, the result will be the same as using the
<P> mode with flash. The desired depth of field will not be obtained.
99
E_3 Changing
the Metering
Mode _
Three methods (metering modes) to measure the subject's brightness
are provided. Normally, evaluative metering is recommended.
In Basic Zone modes, evaluative metering is set automatically.
Select [Metering
mode].
Under the [_:] tab, select [Metering
mode], then press <_-_>.
Sett.emetering
mode.
Select the desired metering mode,
then press <_-_>.
[_8"1Evaluative metering
This is an all-around metering mode suited for
portraits and even backlit subjects. The camera
sets the exposure automatically to suit the
scene.
_3 Partial metering
Effective when the background is much brighter
than the subject due to backlighting, etc. The
gray area in the left figure is where the
brightness is metered to obtain the standard
exposure.
C-I Center=weighted
average metering
The brightness is metered at the center and
then averaged for the entire scene. This
metering mode is for advanced users.
[_
With E83, the exposure
setting will be locked when you press the shutter
button halfway and focus is achieved. With [0:3 and E3, the exposure setting
is set at the moment of exposure. (The exposure setting is not locked when
you press the shutter button halfway.)
100
Setting
Exposure
Compensation
_
Set exposure compensation if the exposure (without flash) does not come out
as desired. This feature can be used in Creative Zone modes (except <M>).
You can set the exposure compensation up to +5 stops in 1/3-stop increments.
Making it brighter:
Hold down the < Avl_> button and
increased
exposurefora brighterimage
turn the <_>
dial to the right.
(Increased exposure)
Making it darker:
Hold down the <Av[+[_>button and
turn the <_>
dial to the left.
(Decreased
exposure)
As shown in the figure, the exposure
level is displayed on the LCD monitor
and in the viewfinder.
Decreased
exposure
fora darkerimage
Dark exposure
After taking the picture, cancel the
exposure compensation
by setting
it back to O.
Increased exposure
for a brighter image
The exposure compensation amount displayed in the viewfinder goes up
to only _+2stops. If the exposure compensation amount exceeds _+2
stops, the end of the exposure level indicator will display <4> or <_>.
The exposure compensation can also be set with [t_ = Expo. comp./
AEB] (p.103). If you wilt set exposure compensation exceeding _+2stops,
you should use ItS: E×po. comp./AEB] to set it.
101
Setting Exposure Compensation *
Set flash exposure compensation if the flash exposure of the subject
does not come out as desired. You can set the flash exposure
compensation up to _+2stops in 1/3-stop increments.
ii! Press the <l]_]> button.
(4HO)
The Quick Control screen will appear
(p.40).
Select
[_].
Press the <_;_> key to select [8_*].
[Flash exposure comp.] will be
displayed at the bottom.
i:
Set the flash
compensation
exposure
amount.
To make the flash exposure brighter,
turn the <_>
dial to the right.
(Increased exposure)
To make it darker, turn the <_>
dial
to the left. (Decreased exposure)
When you press the shutter button
halfway, the <_>
icon wiii appear in
the viewfinder.
After taking the picture, cancel the
flash exposure compensation
by
setting it back to 0.
_[_ If [131:
Auto Ughting Optimizer] (p.107) is set to any setting other than
[Disable], the image may look bright even if a decreased exposure
compensation or decreased flash exposure compensation has been set.
You can also set flash exposure compensation
setting] in [t_" Flash control] (p.167).
102
with [Built-in
flash
func.
Auto Exposure
Bracketing
_
This feature takes exposure compensation a step further by varying the
exposure automatically (up to _+2stops in 1/3-stop increments) with
three shots as shown below. You can then choose the best exposure.
This is called AEB (Auto Exposure Bracketing).
Standard exposure
Darker exposure
(Decreased exposure)
Select
[Expo.
Brighter exposure
(Increased exposure)
comp./AEB].
Under the [t_-'] tab, select [Expo.
comp./AEB], then press <_-_>.
sot
t.oAEB
omoo°t.
Turn the <_>
dial to set the AEB
amount.
AEB amount
Press the <41_> key to set the
exposure compensation amount, if
AEB is combined with exposure
compensation, AEB will be applied
centering on the exposure
compensation amount.
Press < _ > to set it.
When you press the <MENU> button
to exit the menu, the AEB level will be
displayed on the LCD monitor.
Tako
thopioturo.
Focus and press the shutter button
completely. The three bracketed
shots will be taken in this sequence:
Standard exposure, decreased
exposure, and increased exposure.
103
Auto Exposure Bracketing*
Follow steps 1 and 2 to turn off the AEB amount display.
The AEB setting will also be canceled automatically if the power
switch is set to < OFF >, flash recycling is completed, etc.
Using AEB with continuous
shooting:
If <D_j> continuous shooting (p.86) has been set and you press the
shutter button completely, the three bracketed shots will be taken
continuously in this sequence: Standard exposure, decreased
exposure,
and increased exposure.
Using AEB with <1-3> single shooting:
Press the shutter button three times to take the three bracketed
shots. The three bracketed shots will be exposed in the following
sequence: Standard exposure,
exposure.
decreased exposure,
and increased
Using AEB with the self-timer:
If you use the self-timer <_> <_2 > (p.87), the three bracketed
shots wiii be taken continuously after 10 sec. or 2 sec. With <63c>
(p.87) set, the number of continuous shots will be three times the
number set.
I_
Neither flash nor bulb exposures
,
1O4
can be used with AEB.
if [1_11:Auto Lighting Optimizer] (p.107) is set to any setting other than
[Disable], the AEB's effect might be minimal.
Locking the Exposure*
You can lock the exposure when the area of focus is to be different from
the exposure metering area or when you want to take multiple shots at
the same exposure setting. Press the <=X=>button to lock the exposure,
then recompose and take the shot. This is called AE (autoexposure)
lock. It is effective for bacHit subjects.
Focus
the subject.
Press the shutter button halfway.
The exposure setting will be
displayed.
Press
the
< % > button.
(_4)
The <%> icon lights in the viewfinder
to indicate that the exposure setting is
locked (AE lock).
Each time you press the <%> button,
it locks the current autoexposure
setting.
Recompose
and
take the picture.
if you want to maintain the AE lock
while taking more shots, hold down
the <%> button and press the shutter
button to take another shot.
AE lock is applied at the AF
}oint that achieved focus,
Ec3E3
AE lock is applied at the
selected AF point.
AE lock is applied at the center AF point.
When the lens' focus mode switch is set to <MF>, AE tock is applied at the center AF point.
105
=X- Locking
the Flash Exposure
_
If the subject is on the side of the frame and you use flash, the subject may
turn out to be too bright or dark depending on the background, etc. This is
when you should use FE lock. After setting the proper flash exposure for
the subject, you can recompose (put the subject toward the side) and
shoot. This feature can also be used with a Canon EX-series Speedlite.
* FE stands for Flash Exposure.
Press the
< _ > button.
The built-in flash will rise.
Press the shutter button halfway and
look in the viewflnder to check that
the <_> icon is lit.
Focus
the subject.
Press
the< >button.
( 16)
Aim the viewfinder center over the
subject where you want to lock the flash
exposure, then press the <-X--> button.
> The flash will fire a preflash and the
required flash output is calculated
and retained in memory.
In the viewflnder, "FEL" is displayed
for a moment and <_>
will light.
Each time you press the < --X> button, a
preflash is fired andthe required flash output
is calculatedand retained in memory.
Take the picture.
Compose the shot and press the
shutter button completely.
The flash is fired when the picture is
taken.
If the subject is too far away and beyond the effective range of the flash, the
<_> icon will blink. Get closer to the subject and repeat steps 2 to 4.
106
Correcting
the Brightness
andContrast
Automatically
_
If the image comes out dark or the contrast is low, the brightness
and
contrast can be corrected automatically.
This feature is called Auto
Lighting
Optimizer.
The default
setting
is [Standard].
With
JPEG
images,
the correction is done when the image is captured. For RAW images, it can
be corrected with Digital Photo Professional
(provided software, p.270).
Select
[Auto
Under
Lighting
< _'_
Optimizer],
the
Select
< _'_
Optimizer].
[Auto
then
press
>.
Select
,
Lighting
the [t_-'] tab, select
setting.
the desired
setting,
then
press
>.
Take the picture.
The image
will be recorded
brightness
and contrast
with
corrected
the
if
necessary.
Without correction
,
Under [_; Custom
Functions
With correction
(C.Fn)],
if [5: Highlight
tone priority] is
set to [1 : Enable], the Auto Lighting Optimizer will be set automatically to
[Disable] and you cannot change this setting.
Depending on the shooting conditions, noise might increase.
If a setting other than [Disable] is set and you use exposure
compensation, flash exposure compensation, or manual exposure to
darken the exposure, the image might still come out bright. If you want a
darker exposure, set [Auto Lighting Optimizer] to [Disable] first.
In Basic Zone modes, [Standard]
is set automatically.
107
Correcting
the image's
Dark Corners
Due to the lens characteristics, the four corners of the picture might look
darker. This phenomenon is called lens light faIFoff or drop in peripheral
Mumination and can be corrected automatically. The defaWt setting is
[Enable]. With JPEG images, the correction is done when the image is
captured. For RAW images, it can be corrected with Digital Photo
Professional (provided software, p.270).
Se,ect
[Peripher.I
,I.mi..
correct.].
Under the [t_'] tab, select
[Peripheral iHumin, correct.],
press < _-_ >.
then
Select
the,e.i°g.
On the screen, check that
[Correction
data available]
is
displayed for the attached lens.
If [Correction data not available]
displayed, see "About the Lens
,
is
Correction Data" on the next page.
Select [Enable], then press <8>.
T.kethepicture.
The image will be recorded with the
corrected peripheral illumination.
Correction
108
disabled
Correction
enabled
Correcting
theImage's
Dark
Corners
The camera already contains lens peripheral illumination correction
data for about 25 lenses. In step 2, if you select [Enable], the peripheral
light correction will be applied automatically for any lens whose
correction data has been registered in the camera.
With EOS Utility (provided software, p.270),
lenses have their correction data registered
register the correction data for unregistered
Software Instruction Manual (CD-ROM) for
you can check which
in the camera. You can also
lenses. For details, see the
EOS Utility (p.272).
For JPEG images already captured, lens peripheral illumination
correction cannot be applied.
Depending on shooting conditions, noise might appear on the image
periphery.
When using a non-Canon lens, setting the correction to [Disable] is
recommended, even if [Correction
data avaHabme] is displayed.
Lens peripheral
attached.
light correction
is also applied when an Extender is
If the correction data for the attached lens has not been registered to the
camera, the result will be the same as when the correction is set to
[Disable].
The correction amount applied wilt be slightly lower than the maximum
correction amount settable with Digital Photo Professional (provided
software).
If the lens does not have distance information, the correction amount wilt
be lower.
The higher the ISO speed, the lower the correction amount will be.
109
,_=~ Customizing
image Characteristics
_
You can customize a Picture Style by adjusting individual parameters
like [Sharpness] and [Contrast]. To see the resulting effects, take test
shots. To customize [Monochrome],
see page 112.
Select
[Picture
Style].
Under the [131:]tab, select [Picture
Style], then press <8>.
The Picture Style selection screen will
appear.
Select
a Picture
Style.
Select a Picture Style, then press the
<DISP.> button.
The Detail set. screen will appear.
Se,ect
aparameter.
Select a parameter such as
[Sharpness], then press < _-_>.
Set the parameter.
Press the < 41_ > key to adjust the
parameter as desired, then press
< _'_
>,
Press the <MENU>
button to save
the adjusted parameters. The Picture
Style selection screen will reappear.
Any parameter settings different from
the default will be displayed in blue.
110
_-':- Customizing Image Characteristics*
_) Sharpness
Adjusts the sharpness of the image.
To make it less sharp, set it toward the [] end. The closer it is to [],
the softer the image will look.
To make it sharper, set it toward the [] end. The closer it is to [], the
sharper the image will look.
_) Contrast
Adjusts the image contrast and the vividness of colors.
To decrease the contrast, set it toward the minus end. The closer it is
to _1, the blander the image will look.
To increase the contrast, set it toward the plus end. The closer it is to
[], the crisper the image will look.
_o Saturation
The image's color saturation can be adjusted.
To decrease the color saturation, set it toward the minus end. The
closer it is to I_l, the more diluted the colors will look.
To increase the color saturation, set it toward the plus end. The
closer it is to I_l the bolder the colors will look.
Color tone
The skin tones can be adjusted.
To make the skin tone redder, set it toward the minus end. The
closer it is to I_l, the redder the skin tone will look.
To make the skin tone less red, set it toward the plus end. The closer
it is to _, the more yellow the skin tone will look.
By selecting [Default set.] in step 3, you can revert the respective
Picture Styleto its default parameter settings.
To shoot with the Picture Style you modified, follow step 2 on page 79 to
select the modified Picture Style and then shoot.
111
_-'=_Customizing Image Characteristics*
For Monochrome, you can also set [Filter effect] and [Toning effect] in
addition to [Sharpness] and [Contrast] explained on the preceding
page,
t_) Filter Effect
With a filter effect applied to a
monochrome image, you can make
write clouds or green trees stand out
more.
N: None
Normal black-and-white
image with no filter effects.
Ye: Yellow
i The blue sky will look more natural, and the white clouds will look
i crisper.
Or: Orange
i The blue sky will look slightly darker. The sunset wilt look more
brilliant.
R: Red
i The blue sky will look quite dark. Fall leaves wilt look crisper and
brighter.
G: Green
Increasing
(_)Toning
Skin tones and lips wilt look fine. Tree leaves wilt look crisper and
brighter.
the [Contrast]
wilt make the filter effect more pronounced.
Effect
By applying a toning effect, you can
create a monochrome image in that
color. It can make the image look more
impressive.
You can select the following: [N:None],
[S:Sepia], [B:Blue], [P:Purple] or
[G:Green].
112
_=~ RegisteringPreferredimage Characteristics_
You can select a base Picture Style such as [Portrait] or [Landscape],
adjust its parameters as desired and register it under [User Def. 1],
[User Def. 2], or [User Def. 3].
You can create Picture Styles whose parameter settings such as
sharpness and contrast are different. You can also adjust the
parameters of a Picture Style which has been registered to the camera
with EOS Utility (provided software, p.270).
Select
[Picture
Style].
Under the [131:]tab, select [Picture
Style], then press <8>.
The Picture Style selection screen will
appear.
Select
[User
Def.].
Select [User Def. *], then press the
< DISP.> button.
The Detail set. screen will appear.
Press
With [Picture
< _'_
Select
Style] selected, press
>.
the base
Picture
Style.
Press the <AT> key to select the
base Picture Style, then press < 8>.
To adjust the parameters of a Picture
Style which has been registered to
the camera with EOS Utility (provided
software), select the Picture Style
here.
113
_,1_ Registering Preferred Image Characteristics*
Select
a parameter.
Select a parameter such as
[Sharpness], then press < _-_>.
Set the parameter.
Press
the < _
parameter
< _'_
> key to adjust
as desired,
then
the
press
>,
For details,
see "Customizing
Characteristics"
on pages
Image
110-112.
Press the <MENU> button to register
the modified Picture Style. The
Picture Style selection screen will
then reappear.
The base Picture Style will be
indicated on the right of [User Def. *].
The name of the Picture Style having
any modified settings (different from
the default) registered under [User
Def. *] will be displayed in blue.
Ifa Picture Style has already been registered under [User Def. *],
changing the base Picture Style in step 4 will nullify the parameter
settings of the registered Picture Style.
If you execute [Clear aH camera settings] (p.164), all the [User Def. *]
settings will revert to the default. Any Picture Style registered via EOS
Utility (provided software) will have only its modified parameters reverted
to the default setting.
To shoot with a registered
Picture Style, follow step 2 on page 79 to select
[User Def. *] and then shoot.
114
WB: Matching
the Light Source _
The function adjusting the color tone so that white objects look white in
the picture is called white balance (WB). Normally, the <_]> (Auto)
setting will obtain the correct white balance. If natural-looking colors
cannot be obtained with <_W>, you can select the white balance to
match the light source or set it manually by shooting a white object.
Press the
[White
Select
<T WB>
button.
balance] will appear.
the white
balance.
Press the <41_> key or turn the
< _>
dial to select the desired white
balance, then press < __>.
The "Approx. ****K" (K: Kelvin)
displayed for the following white
balance settings < -_ >, < l_& >,
<_>,
<_>
or <_> is the
respective
color temperature.
Custom white balance enables you to manually set the white balance
for a specific light source for better accuracy. Do this procedure under
the actual light source to be used.
Photograph
a white
object.
A plain, white object should fill the
viewfinder's center.
Focus manually and set the standard
exposure for the white object.
You can set any white balance.
115
WB: Matching the Light Source _
Select
[Custom
White
Balance].
Under the [t_:] tab, select [Custom
White Balance], then press < 8>.
The custom white balance selection
screen will appear.
import the white balance data.
Select
step
the image
1, then
press
On the dialog
select
[OK]
that was captured
in
<8>.
screen
which
and the data
appears,
will be
imported.
When
the menu reappears,
press
button to exit the menu.
the
<MENU>
,,,::_iSelect the custom white balance.
,
If the exposure
Press
the <TWB>
Select
[_'._], then
button.
press
<8>.
obtained in step 1 is way off, a correct white balance
might not be obtained.
If the image was captured while the Picture Style was set to
[Monochrome]
(p.80), it cannot be selected in step 3.
Instead of a white object, an 18% gray card (commercially
produce a more accurate white balance.
,
The personal white balance registered with EOS Utility (provided
software, p.270)will be registered under < _.-.d>. If you do step 3, the data
for the registered
116
available) can
personal white balance will be erased.
wB
Adjustingthe ColorTone for the LightSource _
@/=
You can correct the white balance that has been set. This adjustment
will have the same effect as using a commercially-available
color
temperature conversion filter or color compensating filter. Each color
can be corrected to one of nine levels.
This is for advanced users who are familiar with using color temperature
conversion or color compensating filters.
Select
[WB Shift/BKT].
Under the [¢J=] tab, select [WB Shift/
BKT], then press < __>.
The WB correction/WB bracketing
screen will appear.
Set the white
balance
correction.
Press the < _,*_>key to move the ""
mark to the desired position.
B is for blue, A is amber, M is
Sample setting: A2, G1
magenta, and G is green. The color in
the respective direction will be
corrected.
On the upper right, "Shift" indicates
the direction and correction amount.
Pressing the <DISP.> button will
cancel all the [WB Shift/BKT]
settings.
Press <8> to exit the setting and
return to the menu.
During the white balance correction, <WB>
+__ will be displayed in the
viewfinder and on the LCD monitor.
One level ofthe blue!amber correction is equivalent to 5 mireds of a color
temperature conversion filter. (Mired: Measuring unit indicating the
density of a color temperature conversion filter.)
117
_B Adjusting the Color Tone for the Light Source*
With just one shot, three images having a different color balance can be
recorded simultaneously. Based on the color temperature of the current white
balance setting, the image will be bracketed with a bluelamber bias or
magentalgreen bias. This is called white balance bracketing (WB-BKT). White
balance bracketing is possible up to _+3levels in single-level increments.
Set the white balance bracketing amount.
B/A bias _+3levels
In step 2 for white balance correction,
when you turn the <_>
dial, the "m"
mark on the screen will change to "m[] ="
(3 points). Turning the dial to the right sets
the B/A bracketing, and turning it to the
left sets the MIG bracketing.
On the right, "Bracket" indicates the
bracketing direction and correction amount.
Pressing the < DISR> button will cancel
all the [WB Shift/BKT] settings.
Press < 8> to exit the setting and
return to the menu.
Bracketing Sequence
The images will be bracketed in the following sequence: 1. Standard
white balance, 2. Blue (B) bias, and 3. Amber (A) bias, or 1. Standard
white balance, 2. Magenta (M) bias, and 3. Green (G) bias.
During WB bracketing, the continuous shooting speed will be slower. The
maximumburst for continuous shooting will also be lower and the number of
possible shots wilt decrease to one-third the normal number.
You can also set white balance correction and AEB (p.103) together with
white balance bracketing. If you set AEB in combination with white balance
bracketing, a total of nine images will be recorded for a single shot.
Since three images are recorded for one shot, the card will take longer to
record the shot.
"BKT" stands for Bracketing.
118
Setting the Color Reproduction
Range _
iii_iiii;i!ii
The range of reproducible colors is ca[led the color space. With this
camera, you can set the color space to sRGB or Adobe RGB for
captured images. For normal shooting, sRGB is recommended.
In Basic Zone modes, sRGB is set automatically.
Select
[Color
space].
Under the [_:] tab, select [Color
space], then press < _-_>.
Set the desired
color space.
Select [sRGB] or [Adobe RGB], then
press <_-_>.
This color space is mainly used for commercial printing and other
industrial uses. This setting is not recommended if you do not know
about image processing, Adobe RGB, and Design rule for Camera File
System 2.0 (Exif 2.21).
The image wi[[ look very subdued in a sRGB persona[ computer
environment and with printers not compatible with Design rule for
Camera File System 2.0 (Exif 2.21). Post-processing of the image with
software wi[[ therefore be required.
If the image is captured with the color space set to Adobe RGB, the file
name will start with " MG "(first character is an underscore).
The ICC profile is not appended. See explanations about the ICC profile
in the Software Instruction Manual (p.272) in the CD-ROM.
119
Shootingwiththe LCDMonitor
(LiveViewShooting)
You can shoot while viewing the image on the camera's
LCD monitor. This is called "Live View shooting".
Live View shooting
not move,
is effective for still subjects
which do
if you handhold the camera and shoot while viewing the
LCD monitor, camera shake can cause blurred images.
Using a tripod is recommended.
L_JAbout Remote Live View Shooting
With EOS Utility (provided software, p.270) installedin your
computer, you can connect the camera to the computer and shoot
remotely while viewing the computer screen. For details, see the
Software Instruction Manual (p.272) in the CD-ROM
Shooting
with the LCD Monitor
Display the Live View image.
Press the <_>
button.
The Live View image will appear on
the LCD monitor.
The Live View image will closely
reflect the brightness level of the
actual image you capture.
;:::::
Fooo he
sobjeot.
When you press the shutter button
halfway, the camera will focus with
the current AF mode (p.128-134).
Take the picture.
Press the shutter button completely.
The picture will be taken and the
captured image is displayed on the
LCD monitor.
After the image review ends, the
camera will return to Live View
shooting automatically.
Press the <_>
button to exit Live
View shooting.
The image's field of view is approx. 99% (when the image-recording
quality is set to JPEG _ L).
The metering mode wilt be fixed to evaluative metering for Live View
shooting.
In Creative Zone modes, you can check the depth of field by setting [8:
Assign SET button] to [5: Depth=of-field preview] in the [_i Custom
Functions (C.Fn)].
During continuous shooting, the exposure set for the first shot will also
be applied to subsequent shots.
Using <A'DEP> wilt be the same as using <P>.
122
......
r'_ Shooting with the LCD Monitor
Set [Live View shoot.] to [Enable].
In Basic Zone modes, [Live View
shoot.] will be displayed under [131"],and
in Creative Zone modes, it will be
displayed under [t_i].
Battery
Life
with
Temperature
Live
View
Shooting
Shooting
No Flash
[Approx.
number
of shots]
Conditions
50% Flash Use
At 23°C / 73°F
240
220
At 0°C / 32°F
230
210
The figures above are based on a fully-charged Battery Pack LP-E10 and
CIPA (Camera & Imaging Products Association) testing standards.
With a fully-charged Battery Pack LP-E10, continuous Live View shooting is
possible for approx. 2 hr. at 23°C / 73°F and approx. 1 hr. 40 rain. at
0°C / 32°R
@
During Live View shooting, do not point the lens toward the sun. The
sun's heat can damage the camera's internal components.
Cautions for using Live View shooting are on pages 136-137.
When flash is used, there will be two shutter sounds, but only one shot
will be taken.
@
If the camera is not operated for a prolonged period, the power will turn
off automatically as set with [_'" Auto power off] (p.155). If [_" Auto
power off] is set to [Off], the Live View function will terminate
automatically after 30 rain. (camera power remains on).
With an HDMI cable (sold separately), you can display the Live View
image on a TV (p.191).
123
I_ Shooting with the LCD Monitor
Each time you press the < DISP.> button, the information display wH[
change.
AF mode ..............................................................................................
..............
AF point (Quick mode)
- AF[f_: Live mode
...............
Magnifying frame
- AF'._ : Face detection Live mode
................
Histogram
AF_ Quick mode
Shootin_
Eye-Fi card
transmission
status
Auto Lic
Optimizer
Ima(
quality
simulation
AE
Flash-ready
_) Flash off
;i
Battery check
Flash exposure
_
compensation
External flash exposure
compensation
{H High-speed sync
Highlight tone
priority
:
Shutter speed .........
:
...............
ISOspeed
...............
Possible shots
:i
Picture Style
iI
Aperture ...............
:
_Exposurelevelindicator/
AEB range
When <_>
is displayed in white, it indicates that the Live View image
brightness is close to what the captured image will look like.
If <_>
is blinking, it indicates that the Live View image is not being
displayed at the suitable brightness due to low- or bright-light conditions.
However, the actual image recorded will reflect the exposure setting.
If flash is used or bulb is set, the <_>
icon and histogram will be
grayed out (for your reference). The histogram
displayed in low- or bright-light conditions.
124
might not be properly
r_ Shooting with the LCD Monitor
The finaHimage simuHation reflects the effects of the Picture StyHe,white
baHance, etc., in the Live View image so you can see what the captured
image wHHHookHike.
During stHHphoto shooting, the Live View image wHHautomatically reflect
the settings Hsted bellow.
Final image
simulation
during
Live View
shooting
Picture StyHe
* All parameters such as sharpness, contrast, color saturation, and color tone
will be reflected.
White baHance
White baHance correction
Shoot by ambience seHection
Shoot by Hghting or scene type
Exposure
Depth of fieHdpreview (With C.Fn-8-5 set and < _-_> ON)
Auto Lighting Optimizer
PeripheraH iHHuminationcorrection
HighHight tone priority
125
Shooting
Function
Settings
Function settings particular to Live View shooting are explained here.
While the image is displayed on the LCD monitor in Creative Zone
modes, pressing the <[_> button will enable you to set the AF mode,
drive mode, white balance, Picture Style, Auto Lighting Optimizer,
image-recording quality, and ISO speed. In Basic Zone modes, you can
set the AF mode and the settings shown in the table on page 63.
Press
the
< []
> button.
The functions settable with Quick
Control will appear on the left of the
screen.
If the AF mode is < AFt>, the AF
point will also be displayed. You can
also select the AF point.
Select
a function
and set it.
Press the <&T> key to select a
function.
The selected function and Feature
guide (p.47) will appear.
Press the <_>
key or turn the
<_>
dial to change the setting.
Pressing <8>
will display the
respective function's setting screen.
In Creative Zone modes, if [9: Flash button function] is set to [1: ISO
speed] in [_" Custom Functions (C.Fn)], you can raise the built-in flash
with Quick Control. The ISO speed will be set with the <{> button.
126
[_i
_enu
FUnCtiOn
Settings
The menu options below are displayed.
In Basic Zone modes, the Live View
menu options will be displayed under
[t_:], and in Creative Zone modes, they
will be displayed under [t_i].
Live View shooting
You can set Live View shooting to [Enable]
or [Disable].
AF mode
You can select [Live mode] (p.128), [_
Live mode] (p.129), or
[Quick mode] (p.133).
Grid display
With [Grid 1 _] or [Grid 2:E_], yOU can display grid lines, it can
help you level the camera vertically or horizontally.
Metering timer _
You can change how long the exposure setting is displayed (AE lock
time). This option is not displayed in Basic Zone modes. (Metering
timer is fixed at 16 sec.)
The settings for these menu options will apply only to Live View
shooting. They do not take effect during viewfinder shooting.
If you select [t_.: Dust Delete Data], [_: Clean manually], [_-" Clear
settings], or [_-" Firmware Vet.I, the Live View shooting will terminate.
127
Changing
the Autofocus
Mode
The AF modes available are [Live mode], [_ Live mode] (face
detection, p.129), and [Quick mode] (p.133).
if you want to achieve precise focus, set the lens focus mode switch to
<MF>, magnify the image, and focus manually (p.135).
Select
the AF mode.
Under the [_i] tab, select [AF mode].
Select the desired AF mode, then
press < _ >.
While the Live View image is
displayed, you can press the <[_>
button to select the AF mode on the
Quick Control screen (p.126).
The
Live
with
with
image sensor is used to focus. Although AF is possible with the
View image displayed, the AF operation will take longer than
the Quick mode. Also, achieving focus may be more difficult than
the Quick mode.
Display
the Live View
Press the <r_>
image.
button.
The Live View image will appear on
the LCD monitor.
The AF point <[_> will appear.
Move
AF point
128
the AF point.
Press the < ,,_ > key to move the AF
point to where you want to focus (it
cannot go to the edges of the picture).
To return the AF point to the center,
press <8>.
(if C.Fn-8 has been set,
press <Avr_> + <_-_>.)
Changing the Autofocus Mode
Focus the subject.
Aim the AF point over the subject and
press the shutter button halfway.
When focus is achieved, the AF point
wiii turn green and the beeper wiii
sound.
if focus is not achieved, the AF point
wiii turn orange.
Take the picture.
Check the focus and exposure, then
press the shutter button completely to
take the picture (p.122).
With the same AF method as the Live mode, human faces are detected
and focused. Have the target person face the camera.
Display
the
Live View
image.
Press the <l:_> button.
The Live View image will appear on
the LCD monitor.
When a face is detected, the <[ ]>
frame will appear over the face to be
focused.
if multiple faces are detected, <{ }>
will be displayed. Press the <4_>
key to move the <( }> frame over
the desired target face.
129
Changing the Autofocus Mode
Focus
t.esubject.
@ Press the shutter button halfway
the camera wiii focus the face
covered
When
by the <[ ]> frame.
focus
is achieved,
wiii turn green
sound.
if focus
and
the AF point
and the beeper
is not achieved,
wiii turn orange.
@ if a face cannot
wiii
the AF point
be detected,
the AF
point <_> wiii be displayed
and AF
wiii be executed
at the center.
Take the picture.
Check
press
the focus
the shutter
take the picture
and exposure,
button
then
completely
to
(p.122).
If the focus is way off, face detection will not be possible. If the lens
enables manual focusing even while the lens focus mode switch is set to
<AF>, turn the focusing ring to attain rough focus. The face will then be
detected and <[ ]> will be displayed.
An object other than a human face might be detected as a face.
Face detection will not work if the face is very small or large in the picture,
too bright or too dark, titled horizontally or diagonally, or partially hidden.
The <[ ]> focusing frame might cover only part of the face.
When you press <C)>, the AF mode will switch to the Live mode
(p.128). You can press the <_> key to move the AF point. Press <{_>
again to return to the _ (face detection) Live mode. (If C.Fn-8 has been
set, press <Av[]> + <C)>.)
Since AF is not possible with a face detected near the edge of the
picture, the <[ ]> will be grayed out. Then if you press the shutter button
halfway, the center AF point <[_> wilt be used to focus.
130
Changing
theAutofocus
Mode
AF operation
@ Focusing wiii take slightly longer.
Even when focus has been achieved, pressing the shutter button
halfway wiil focus again.
The image brightness may change during and after the AF
operation.
if the Hightsource changes while the Live View image is displayed,
the screen might flicker and focusing may be difficult, if this
happens, stop the Live View shooting and autofocus under the
actual Hightsource first.
if you press the <O,> button in the Live mode, the image wiil be
magnified at the AF point, if focusing is difficult in the magnified view,
return to the normal view and autofocus. Note that the AF speed
may differ between the normal and magnified views.
if you autofocus in the Live mode's normal view and then magnify
the image, the focus might be off.
in the _ Live mode, pressing the <_> button wiil not magnify the
image.
In the Live mode or _ (face detection) Live mode, if you shoot a
peripheral subject and it is slightly out of focus, aim the center AF point
over the subject to focus, then take the picture.
The AF-assist beam will not be emitted. However, if an EX-series
Speedlite (sold separately) equipped with a LED light is used, the LED
light wilt turn on for AF-assist when necessary in the Live mode and
(face detection) Live mode.
131
Changing the Autofocus Mode
iiii_i!iii!i_i!iii!i_i!iii!i_i!iii!il
:!il
iiiiili_i_
Shooting conditions which can make focusing difficult:
Low-contrast subjects such as the blue sky and solid-color, flat
surfaces.
Subjects in low light.
Stripes and other patterns where there is contrast only in the
horizontal direction.
Under a light source whose brightness, color, or pattern keeps
changing.
Night scenes or points of light.
Under fluorescent lighting or when the image flickers.
Extremely small subjects.
Subjects at the edge of the picture.
Subjects strongly reflecting light.
The AF point covers both a near and faraway subject (such as an
animal in a cage).
Subjects which keep moving within the AF point and cannot keep
still due to camera shake or subject blur.
A subject approaching or moving away from the camera.
Autofocusing while the subject is way out of focus.
Soft focus effect is applied with a soft focus lens.
A special effects filter is used.
132
Changing the Autofocus Mode
The dedicated AF sensor is used to focus in One-Shot AF mode (p.81),
using the same AF method as with viewfinder shooting.
Although you can focus the target area quickly, the Live View image
will be interrupted
momentarily
during the AF operation.
AF point
Display
the
Live View
Press the <r_>
image.
button.
The Live View image will appear on
the LCD monitor.
The small boxes on the screen are
the AF points, and the larger box is
the magnifying frame.
Magnifying
frame
Select
the AF
point.
_
Press the <[_> button ((_10)to
display the Quick Control screen.
The settable functions will be
displayed on the left of the screen.
Press the <AT> key to make the AF
point selectable.
Turn the <_>
dial to select the AF
point.
133
Changing the Autofocus Mode
Focus
the subject.
Aim the AF points over the subject
and press the shutter button halfway.
The Live View image will turn off, the
reflex mirror will go back down, and
AF will be executed.
When focus is achieved, the AF point
which achieved focus will turn green
and the Live View image will
reappear.
If focus is not achieved, the AF point
will turn orange and blink.
Take the picture.
Check the focus and exposure, then
press the shutter button completely to
take the picture (p.122).
You cannot take a picture during autofocusing.
Live View image is displayed.
134
Take the picture while the
MF: Focusing Manually
You can magnify the image and focus precisely manually.
Set the lens focus
mode
switch
to
<MF>.
Turn the lens focusing ring to focus
roughly.
Magnifying frame
Move the magnifying
frame.
Press the < _;, > key to move the
magnifying frame to the position
where you want to focus.
To return the magnifying frame to the
center, press < _-_>. (If C.Fn-8 has
been set, press <Avr_> + <8>.)
Magnify the image.
Press the <¢,> button.
The area within the magnifying frame
will be magnified.
Each time you press the < _ > button,
the view will change as follows:
_.
5x --* lOx _ Normal view
Focusmanua.y.
AE lock
While looking at the magnified image,
turn the lens focusing ring to focus.
After achieving focus, press the < ¢, >
button to return to the normal view.
Magnified area position
Magnification
Take the picture.
Check the focus and exposure, then
press the shutter button to take the
picture (p.122).
135
Live View
Shooting
Cautions
White <_J> and Red <_]l> Internal Temperature Warning icons
,
,
If the camera's internal temperature increases due to prolonged Live
View shooting or a high ambient temperature, a white <_> icon will
appear, if you continue shooting while this icon is displayed, the image
quality of still photos may deteriorate. You should stop the Live View
shooting and allow the camera to cool down before shooting again.
if the camera's internal temperature further increases while the white
<_> icon is displayed, a red <H> icon will start blinking. This blinking
icon is a warning that the Live View shooting wilt soon be terminated
automatically. If this happens, you will not be able to shoot again until the
camera's internal temperature decreases. Turn off the power and let the
camera rest for a while.
,
Shooting with the Live View function at a high temperature for a
prolonged period will cause the <H> and <H> icons to appear earlier.
When not shooting,
turn off the camera.
Live View Image Cautions
,
,
,
,
,
136
Under low- or bright-light conditions, the Live View image might not
reflect the brightness of the captured image.
if the light source within the image changes, the screen might flicker, if
this happens, stop the Live View shooting and resume shooting under
the actual light source to be used.
if you point the camera in a different direction, it might throw off the Live
View image's correct brightness momentarily. Wait until the brightness
level stabilizes before shooting.
If there is a very bright light source in the picture, such as the sun, the
bright area might appear black on the LCD monitor. However, the actual
captured image will correctly show the bright area.
in low light, if you set the [_: LCD brightness]
to a bright setting,
chrominance noise may appear in the Live View image. However, the
chrominance noise will not be recorded in the captured image.
When you magnify the image, the image sharpness may look more
pronounced than it really is.
Live View
Shooting
Shooting
Cautions
Resutt Cautions
When you shoot continuously with the Live View function for a tong
period, the camera's internal temperature may increase and it can
degrade image quality. Terminate Live View shooting when not shooting
images.
Before taking a tong exposure, stop Live View shooting temporarily and
wait several minutes before shooting. This is to prevent image
degradation.
Live View shooting in high temperatures and at high ISO speeds may
cause noise or irregular colors.
When you shoot at high ISO speeds, noise (banding, dots of light, etc.)
may become noticeable.
if you take the picture during magnified view, the exposure might not
come out as desired. Return to the normal view before taking the picture.
During the magnified view, the shutter speed and aperture will be
displayed in orange. Even if you take the picture during magnified view,
the image will be captured in the normal view.
if [_: Auto Lighting Optimizer]
(p.107) is not set to [Disable], the
image may look bright even if a decreased exposure compensation or
decreased flash exposure compensation has been set.
If you use a TS-E lens to shift the lens vertically or use an Extension
Tube, the standard exposure might not be obtained or an irregular
exposure may result.
Custom Function Cautions
During Live View shooting, certain Custom Function settings wilt not take
effect (p.217).
Lens and Flash Cautions
The focus preset feature on super telephoto lenses cannot be used.
FE lock is not possible when the built-in flash or an external Speedlite is
used. Modeling flash will not work with an external Speedlite.
137
Shooting Movies
<_,_,>, you can shoot HighDefinition (HD) movies. The
movie
recording format will be
When
MOV. you set the Mode Dial to
_L_ Cards
which
can record
movies
When shooting movies, use a large-capacity SD card rated SD
Speed Class 6 "CLASSy"
or higher.
If you use a slow-writing card when shooting movies, the movie
might not be recorded properly. And if you playback a movie on a
card having a stow reading speed, the movie might not playback
properly.
To check the card's read/write speed, refer to the card
manufacturer's Web site.
bm,,Shooting Movies
When you set the shooting mode to <Din>, you can easily shoot HighDefinition (HD) movies with autoexposure. When playing movies,
connecting the camera to a TV set is recommended (p.184, 191).
Set the Mode
...........................................
i_\...........
IL.................
Dial to <J,_,>.
The reflex mirror wiil make a sound,
then the image wiil appear on the
LCD monitor.
Focus
the subject.
Before shooting a movie, autofocus
or manual focus (p.128-135).
When you press the shutter button
halfway, the camera wiil focus with
the current AF mode.
Shoot
Recording
movie
Microphone
140
the
movie.
Press the <t'_> button to start
shooting a movie. To stop movie
shooting, press <r_> again.
While the movie is being shot, the
"O" mark wiil be displayed on the
upper right of the screen.
_
@
@
@
Shooting Movies
In the movie shooting mode, you cannot take a still photo even if you
press the shutter button completely.
During movie shooting, do not point the lens toward the sun. The sun's
heat can damage the camera's internal components.
Cautions for movie shooting are on pages 150 and 151.
if necessary, also read the Live View shooting
cautions on pages
136 and 137.
A movie file is recorded each time you shoot a movie.
The image's field of view is approx. 99%.
The ISO speed, shutter speed, and aperture are set automatically.
AE lock is possible by pressing the <-)(- > button (p.105). To cancel AE
lock during movie shooting, press the < E_ > button.
By holding down the <Av[]> button and turning the <._%> dial, you can
set the exposure compensation.
When you press the shutter button halfway, the exposure setting
displayed at the screen bottom is for your reference.
The sound will be recorded by the camera's built-in monaural
microphone (p.140).
The sound recording level will be adjusted automatically.
With a fully-charged Battery Pack LP-E10, the total shooting time will be
as follows: At 23°C/73°F: Approx. 1 hr. 50 min., At 0°C/32°F: Approx.
1 hr. 30 rain.
This camera is compatible with the function turning on the LED light
automatically in low-light conditions. For details, see the EX
Speedlite's instruction manual.
141
"_ Shooting Movies
Each time you press the < DISP.> button, the information display wH[
change.
Movie shooting
mode ...........................
Frame rate
Movie shooting remaining time/
AF mode ...........................................................................
Elapsed time
. AFI_IM Live mode
- AF_;
Face detection
.................
AF point (Quick mode)
Live mode
..............
Magnifying frame
- AF_
Quick mode
................
Recording
movie
White
Picture
Auto Li
Optimizer
Movie recordin_
f check
ii
LED light ................
Shutter speed ................
Aperture ................
;
ii ii
.............
Movie
autoexposure
Eye-Fi card
transmission
status
................
ISO speed
..............
Exposure compensation
amount
If there is no card in the camera, the movie shooting remaining time will
be displayed in red.
When movie shooting starts, the movie shooting remaining time will
change to the elapsed time.
142
",_, Shooting Movies
The final image simulation reflects the effects of the Picture Style, white
balance, etc., in the movie image so you can see what the captured
movie will look like.
During movie shooting, the movie image will automatically
settings listed below.
Final image
simulation
for movie
reflect the
shooting
Picture Style
* All parameters such as sharpness, contrast, color saturation, and color tone
will be reflected.
White balance
Exposure
Depth of field
Auto Lighting Optimizer
Peripheral illumination correction
Highlight tone priority
143
Shooting
Function
Settings
Function settings particular to movie shooting are explained
here.
While the movie image is displayed on the LCD monitor, you can press
the <[_> button to enable the following to be set: AF mode, white
balance, Picture Style, and Auto Lighting Optimizer.
Press
the
<[_>
button.
(4H0)
The functions settable with Quick
Control will appear on the left of the
screen.
If the AF mode is < AFt>, the AF
point will also be displayed.
Select
a function
and set it.
Press the <&T> key to select a
function.
The selected function and Feature
guide (p.47) will appear.
Press the <_>
key or turn the
<_>
dial to change the setting.
Pressing <8>
will display the
respective function's setting screen.
144
Menu Function
The menu options displayed
explained below.
Settings
under the [',_,'], [',_,:], and [',_J] tabs are
[',_,'] tab
AF mode
The AF modes will be the same as described on pages 128-134.
You can select [Live mode], [_ Live mode], or [Quick mode]. Note
that continuous focusing of a moving subject is not possible.
AF with shutter button during '_ (movie recording)
When [Enable] is set, AF is possible during movie shooting.
However, continuous autofocusing is not possible, if you autofocus
during movie shooting, you might momentarily throw the focus way
off or change the exposure. The movie will also record the lens
operation noise.
During movie shooting, if the [Quick mode] AF mode is set, AF will
be executed in [Live mode].
The settings under the [",_,'I',_,:P,_,"] menu tabs will take effect only
in the <Din> mode. They will not be applied in shooting
modes other
than the <Din> mode.
The [AF mode]
setting will also be applied to Live View shooting.
145
Menu Function Settings
D_ShuttedAE
lock button
You can change the function assigned to the shutter button's halfway
position and to the AE lock button.
* AF/AE lock:
Normal function. Press the shutter button halfway to execute AF.
Press the <-)(-> button for AE lock.
* AE Iock/AF:
Press the shutter button halfway for AE lock. For AF, press the
<-X-> button. Convenient when you want to focus and meter at
different parts of the picture.
* AF/AF lock, no AE lock:
Press the shutter button halfway to execute AF. While you
autofocus by pressing the shutter button halfway, you can pause
the autofocus by holding clown the <_> button. You can resume
the autofocus by letting go of the <-X-> button. AE lock is not
possible.
* AE/AF, no AE lock:
Press the shutter button halfway for metering. For AF, press the
<-X-> button. AE lock is not possible.
D_Highlight
tone priority
If [Enable] is set, highlight detail will be improved. The dynamic
range is expanded from the standard 18% gray to bright highlights.
The gradation between the grays and highlights becomes smoother.
The settable ISO speed range will be ISO 200-6400. The Auto
Lighting Optimizer will also be set automatically to [Disable] and
cannot be changed.
146
Menu
Function
Settings
[',_,:] tab
Movie recording size
The movie wiii be recorded in [1280x720] High-Definition (HD)
quality. You can select the frame rate [1_0]or [[_s] (recorded frames
per second) to suit your TV set's video format.
* The frame rate is expressed as fps or frames per second.
[1_0]
: For areas where the TV video format is NTSC (North
America, Japan, Korea, Mexico, etc.).
: For areas where the TV video format is PAL (Europe,
Russia, China, Australia, etc.).
[[_s]
Total Movie
Recording
Time
and File Size per Minute
Due to the file system, movie shooting will stop automatically
if the
file size of a single movie clip reaches 4GB.
You can immediately resume shooting another movie by pressing
the < r"ll> button. (A new movie file starts being recorded.)
[1280x720]
_0 [_s
17 min.
34 min.
1 hr. 8 min.
222.6 MB/min.
An increase of the camera's internal temperature may cause movie
shooting to stop before the maximum recording time shown in the table
above (p.150).
The maximum recording time of one movie clip is 29 min. 59 sec.
Movie shooting in Full High-Definition (Full HD) or Standard Definition
(SD) quality is not possible.
With ZoomBrowser EX/ImageBrowser
(provided software, p.270), you
can extract still photos from a movie. The quality of the extracted still
photo will be [1280x720] for about 920,000 pixels.
147
Menu
Function
Settings
@ Sound recording
When the sound recording is set to [On], sound wiii be recorded by
the built-in monaural microphone. The sound recording level wiil be
adjusted automatically. An external microphone cannot be used.
Metering timer
You can change how long the exposure setting is displayed (AE lock
time).
Grid display
With [Grid 1 _]
or [Grid 2:E_], yOU can display grid lines. It can
help you [eve[ the camera vertically or horizontally.
The sound wilt be recorded at a 48 kHz sampling frequency
for both L and R.
and 16-bit
The Metering timer and Grid display settings wilt also be reflected in Live
View shooting.
148
Menu
Function
Settings
[ ',_,-"] tab
Exposure compensation
You can set exposure compensation
1/3-stop increments.
for movies up to _+3stops in
Auto Lighting Optimizer
The Auto Lighting Optimizer can be set as explained on page 107.
If the [',_,'] menu tab's [_Highlight
tone priority] is set to
[Enable], the Auto Lighting Optimizer will be set automatically to
[Disable] and cannot be changed.
Custom
White
Balance
As explained on page 115, the image for custom white balance can
be selected. Note that still photos cannot be taken in the <_>
mode. Set a shooting mode other than <_>
and take a still photo.
Then select it for the custom white balance.
Picture Style
The Picture Style can be set as explained on pages 79.
149
About the Red <H>
internal Temperature
Warning
icon
If the camera's internal temperature is high, a blinking red icon <H> may
appear. This blinking icon is a warning that the movie shooting will soon
be terminated automatically. If this happens, you will not be able to shoot
again until the camera's internal temperature decreases. Turn off the
power and let the camera rest for a while.
Movie shooting at a high temperature for a prolonged period will cause
the <H> icon to appear sooner. When not shooting, turn off the camera.
Movie
Shooting
Cautions
Recording and image Quality
,
If the attached lens has an image Stabilizer, the Image Stabilizer will
operate at all times even if you do not press the shutter button halfway.
The image Stabilizer will thereby consume battery power and may
shorten the total movie shooting time or decrease the number of possible
shots. If you use a tripod or if the image Stabilizer is not necessary, you
should set the IS switch to <OFF>.
,
The camera's
noise.
,
If movie shooting is not possible due to insufficient remaining capacity of
the card, the movie recording size and movie shooting remaining time
(p.142) will be displayed in red.
If you use a card having a slow writing speed, a five-level
indicator might appear on the right of the screen during
movie shooting. It indicates how much data has not yet been
written to the card (remaining capacity of the internal buffer
memory). The slower the card, the faster the indicator will
climb upward, tf the indicator becomes full, movie shooting
,
built-in microphone
will also record camera operation
will stop automatically.
Indicator
If the card has a fast writing speed, the indicator will either
not appear or the level (if displayed) will hardly go upward.
First, shoot a few test movies to see if the card can write fast enough.
150
Movie
Shooting
Cautions
Playback and TV connection
If the brightness changes during movie shooting, that part might took
momentarily still when you playback the movie.
If you connect the camera to a TV set with an HDMI cable (p.191) and
shoot a movie, the movie being shot will be displayed at a small size on
the TV. But the movie wilt still be properly recorded in High-Definition
(HD) quality.
If you connect the camera to a TV set and shoot a movie, the TV will not
output any sound during the shooting. However, the sound will be
properly recorded.
151
Handy Features
Silencing the Beeper (p.154)
Card Reminder (p.154)
Setting the Image Review Time (p.154)
Setting the Auto Power-off Time (p.155)
Adjusting the LCD Monitor Brightness (p.155)
Creating and Selecting a Folder (p.156)
File Numbering Methods (p.158)
Setting Copyright Information (p.160)
Auto Rotation of Vertical Images (p.162)
Checking Camera Settings (p.163)
Reverting the Camera to the Default Settings (p.164)
Turning the LCD Monitor Off!On (p.166)
Changing
the Shooting Settings Screen Color (p.166)
Setting the Flash (p.167)
Appending
Dust Delete Data (p.171)
Manual Sensor Cleaning (p.173)
Handy Features
You can prevent the beeper from sounding when focus is achieved or
during self-timer operation.
Under the [_'] tab, select [Beep], then
press < _-_>. Select [Disable], then
press <_-_>.
iii!i!ii!i
¸
!i!i!iiiii
i
i !i !a!iiiiiiii! i !i! ia! ii!!i!i!i
This prevents shooting if there is no card in the camera.
Under the [t_'] tab, select [Release
shutter without card], then press
<__>. Select [Disable], then press
<8
> .
If there is no card installed and you press
the shutter button, "Card" will be
displayed in the viewfinder, and you
cannot release the shutter.
You can set how long the image is displayed on the LCD monitor
immediately after capture. If [Off] is set, the image will not be displayed
immediately after image capture. If [Hold] is set, the image review will
be displayed up until the [Auto power off] time.
During image review, if you operate any camera controls such as
pressing the shutter button hal%,ay, the image review will end.
Under the [t_'] tab, select [Image
review], then press <_-_>. Select the
desired setting, then press < _-_ >.
154
Handy Features
To save battery power, the camera turns off automatically after the set
time of idle operation elapses. You can set this auto power-off time.
When the camera has turned off due to auto power off, you can wake it
up by pressing the shutter button halfway or pressing any of the
following buttons: <MENU>, <1_1>, <_>,
etc.
If [Off] has been set, either turn off the camera yourself or press
the <DISP.> button to turn off the LCD monitor to save battery
power.
Even if [Off] has been set and the camera is not used for 30 min.,
the LCD monitor will turn off automatically.
To turn on the LCD
monitor again, press the <DISP.> button.
Under the [_'] tab, select [Auto power
off], then press < _ >. Select the desired
setting, then press <_-_>.
You can adjust the brightness of the LCD monitor to make it easier to read.
Under the [_':] tab, select [LCD
brightness],
then press <8>.
With the
adjustment screen displayed, press the
< 4_ > key to adjust the brightness, then
press < _-_ >.
When checking the exposure of an
image, set the LCD monitor brightness to
4 and prevent the ambient light from
affecting the reviewed image.
155
Handy Features
You can freely create and select the folder where the captured images
are to be saved.
This is optional since a folder will be created automatically
captured images.
for saving
Create a Folder
l
Select
[Select
folder].
Under the [_'] tab, select [Select
folder], then press < _-_>.
, Se,eot
[Createfo der].
Select [Create folder],
Create
then press
a new folder.
Select [OK], then press <__>.
A new folder with a higher one-up
folder number is created.
156
Handy Features
Selecting a Folder
Lowest file number
Number of images
in folder
With
the folder
displayed,
< _'_
selection
screen
select
a folder
and press
where
the captured
>.
The folder
images
will be saved
is selected,
Subsequent
captured
images will be
recorded
into the selected
folder,
Folder name
Highest file number
About
Folders
As with "100CANON" for example, the folder name starts with three digits
(folder number) followed by five alphanumeric characters. A folder can contain
up to 9999 images (file No. 0001 - 9999). When a folder becomes full, a new
folder with a higher one-up folder number is created automatically. Also, if
manual reset (p.159) is executed, a new folder will be created automatically.
Folders numbered from 100 to 999 can be created.
Creating
Folders with a Personal
Computer
With the card open on the screen, create a new folder named "DCIM". Open
the DCIM folder and create as many folders as necessary to save and
organize your images. The folder name must follow the "100ABC_D" format
where the first three digits is 100 - 999 followed by five alphanumeric
characters. The five characters can be a combination of upper- or lower-case
letters from A to Z, numerals, and an underscore "_". There can be no space in
the folder name. Also, folder names cannot have the same three-digit number
such as "100ABC D" and "I00W XYZ" even if the letters are different.
157
Handy Features
The image files wiii be numbered from 0001 to 9999 in the order the
images are taken, then saved in a folder. You can change how the file
number is assigned.
The file number wiii appear on your computer in this format:
IMG O001.JPG.
Under the [_"] tab, select [File
numbering], then press <8>.
The
available settings are described below.
Select one, then press <_-_>.
[Continuous]:
The file numbering continues
in sequence even
after you replace the card or create a folder.
Even after you replace the card or create a new folder, the file
numbering continues in sequence up to 9999. This is convenient
when you want to save images numbered anywhere between 0001
to 9999 in multiple cards or folders into one folder in your personal
computer.
If the replacement card or existing folder already contains images
recorded previously, the file numbering of the new images might
continue from the file numbering of the existing images in the card or
folder. If you want to use continuous file numbering, you should use
a newly-formatted card each time.
File numbering after
replacing the card
Nextsequential file number
158
File numbering after
creating a folder
Handy Features
!!iiii!iiiiiii!iiiiiii!iiii!
iiii_i!iii!i_i!iii!i_i!iii!i_i!i!i!
[Auto reset]: The file numbering is reset to 0001 whenever you
replace the card or create a folder.
Whenever the card is replaced or a new folder created, the file
numbering starts from 0001. This is convenient if you want to
organize images according to cards or folders.
If the replacement card or existing folder already contains images
recorded previously, the file numbering of the new images might
continue from the file numbering of the existing images in the card or
folder. If you want to save images with the file numbering starting
from 0001, use a newly formatted card each time.
File numbering after
replacing the card
File numbering after
creating a folder
File numbering is reset
[Manual reset]: To reset the file numbering to 0001 manually
to start from file number 0001 in a new folder.
or
When you reset the file numbering manually, a new folder is created
automatically and the file numbering of images saved to that folder
starts from 0001.
This is convenient
if you want to use different folders for the images
taken yesterday and the ones taken today, for example.
Alter the manual reset, the file numbering returns to continuous or
auto reset. (There will be no Manual reset confirmation screen.)
If the file number in folder No. 999 reaches 9999, shooting will not be
possible even if the card still has storage capacity.The LCD monitorwill
display a message telling you to replace the card. Replace itwith a new
card.
For both JPEG and RAW images, the file name will start with "IMG_". Movie
file names will start with "MVI ". The extension will be ".JPG" for JPEG
images, ".CR2" for RAW images, and ". MOV" for movies.
159
Handy Features
When you set the copyright information,
image as Exif information.
it will be appended to the
Select [Copyright
information].
Under the [_] tab, select [Copyright
information], then press <8>.
Select the option to be set.
Select [Enter author's name] or
[Enter copyright
details], then press
<8
> .
The text entry screen will appear.
Select [Display copyright info.] to
check the copyright information
currently set.
Select [Delete copyright
information] to delete the copyright
information currently set.
Enter text.
Refer to "Text Entry Procedure" on
the next page and enter the copyright
information.
Enter up to 63 alphanumeric
characters and symbols.
,,:_i Exit the setting.
After entering the text, press the
<MENU> button to exit.
160
Handy
Features
Text Entry Procedure
Changing the entry area:
Press the < [] > button to toggle
between the top and bottom entry
areas.
Moving
the
cursor:
Press the <4_>
cursor.
key to move the
Entering text:
In the bottom area, press the <,;,> key or turn the <_>
select a character, then press <_-_> to enter it.
dial to
Deleting a character:
Press the <-_ > button to delete one character.
Exiting:
After entedng the text, press the < MENU > button to finafize the text
entry and return to the screen in step 2.
Canceling the text entry:
To cancel the text entry, press the < DISP.> button to cancel it and
return to the screen in step 2.
You can also set or check the copyright information
with EOS Utility
(provided software, p.270).
161
Handy Features
Vertical images are rotated automatically so they are
displayed vertically on the camera's LCD monitor
and on the personal computer instead of horizontally.
The setting of this feature can be changed.
Under the [_"] tab, select [Auto rotate],
then press < _ >. The available settings
are described below. Select one, then
press <_-_>.
[On I_ _]
: The vertical image is automatically rotated during playback
[On _]
: The vertical image is automatically
computer.
[Off]
: The vertical image is not automatically
on both the camera's LCD monitor and on the computer.
rotated only on the
rotated.
The vertical image is not rotated during the image review
immediately
after it is captured.
Press the < [] > button and the image playback will display the
rotated image.
[On a _] is set, but the image does not rotate during playback.
Auto rotate will not work with vertical images captured while [Auto
rotate] was set to [Off]. If the vertical image is taken while the camera
is pointed up or down, the image might not be rotated automatically for
playback. In such a case, see "Rotating the Image" on page 179.
On the camera's LCD monitor, I want to rotate an image
captured when [On _] had been set.
Set [On_ _], then playback the image. It will be rotated.
The vertical image does not rotate on the computer screen.
The software used is not compatible with image rotation. Use the
software provided with the camera instead.
162
Handy Features
While the menu is displayed, press the <DISP.> button to display the
camera's major function settings.
While the menu is displayed, press
the <DISP.> button to display the
settings.
Press the <DISP.> button again to
return to the menu.
Settings
display
remaining
capacity
correction (p.117)/
WB bracketing (p.118)
Live View shooting (p.121 )
Red-eye
reduction (p.89)
Auto rotate display (p.162)
.....................
DatelTime (p.33)
..................................
Beeper (p.154)
.......................................................
Auto power off (p.155)
163
Handy Features
The camera's shooting settings and menu settings can be reverted to
the default. This can be done in Creative Zone modes.
'
Select [Clear settings].
Under the [_] tab, select [Clear
settings], then press < _-_>.
Select
[Clear
all camera
settings].
Select [Clear all camera settings],
then press <_-_>.
Select
[OK].
Select [OK], then press <8>.
Setting [Clear all camera settings]
will reset the camera to the default
settings on the next page.
Clearing all camera settings:
After the procedure above, go to [_4 Clear settings] and select
[Clear all Custom Func. (C.Fn)] to clear all the Custom Function
settings (p.216).
164
Handy Features
Shooting
Settings
One-Shot AF
Automatic selection
[]
Image-recording
(Single shooting)
Standard
E_]](Evaluative
metering)
Enable/
Correction
retained
AUTO (Auto)
Max.: 3200
Canceled
Unchanged
Continuous
Settings
30 sec.
Enable
Brightness
(10 images)
On_l
Shutter button
Unchanged
Unchanged
Enable
Unchanged
Disable
Disable
Unchanged
View
(Auto)
Canceled
Canceled
2 sec.
Live
_]
0 (Zero)
Enable
Shooting
Settings
Enable
Live mode
Off
16 sec.
data
sRGB
Canceled
Camera
Settings
tL
Standard
Erased
Movie
Shooting
Settings
Live mode
Disable
AF/AE lock
Disable
Unchanged
On
16 sec.
Off
Canceled
Standard
Canceled
Standard
165
Handy Features
........................... ....................................................
The shooting settings display (p.46) can be turned on or off by pressing
the shutter button halfway.
Under the [_:] tab, select [LCD off/on
btn], then press <_-_>. The available
settings are described below. Select one,
then press <_-_>.
[Shutter
btn.]
: When you press the shutter button halfway, the
display will turn off. And when you let go of the
shutter button, the display will turn on.
[Shutter/DISP]:
[Remains
on]
When you press the shutter button halfway, the
display will turn off. And when you let go of the
shutter button, the display will remain off. To turn on
the display, press the <DISP.> button.
: Display remains on even when you press the shutter
button halfway. To turn off display, press the < DISP.>
button.
You can change the background color of the shooting settings screen.
Under the [_'] tab, select [Screen
color], then press <_-_>. Select the
desired color, then press <_-_>.
When you exit the menu, the selected
color will be displayed for the shooting
settings screen.
166
Setting
the Flash _
The built-in flash and external Speedlite settings can be set with the
camera's menu. You can use the camera's menu to set the external
Speedlite function settings only if the attached EX-series
Speedlite
is
compatible with this function.
The setting procedure is the same as setting a camera menu function.
Select
[Flash
control].
Under the [_'] tab, select [Flash
control], then press <8>.
The flash control screen will appear.
Normally, set this to [Enable].
If [Disable] is set, neither the builtin flash nor the external Speedlite
will fire. This is useful when you only
want to use the fiash's AF-assist
beam.
With [Built-in flash func. setting] and [External flash func. setting],
you can set the functions listed on the next page. The functions
displayed under [External flash func. setting] will vary depending on
the Speedlite model.
Select [Built-in flash func. setting]
or [External flash func. setting].
The flash functions will be displayed.
The functions not dimmed can be
selected and set.
Even if [Flash firing] has been set to [Disable], if focus is difficult to achieve
in low light, the built-in flash may still fire a series of flashes (AF-assist
beam, p.84).
167
Setting the Flash _
[Built=in flash func. setting] and [External
setting] Settable Functions
E-TTL 11(Fixed)
flash func.
©
©
--
I
168
169
©
©
-102
©
169
--
©
--
--
©
--
* Regarding [FEB] (Flash exposure bracketing), [Zoom], and [Wireless set.],
refer to the Speedlite's instruction manual.
Flash mode
With an external Speedfite, you can select the flash mode suiting
your objective.
[E-TTL II] is the standard mode of
EX-sedes Speedlites for automatic
flash shooting.
[Manual flash] enables you to set the
flash output yourself. This is for
advanced users.
For other flash modes, refer to your
Speedfite's instruction
168
manual.
Setting the Flash _
Shutter sync.
Normally, set this to [1st curtain] so that the flash fires immediately
after the exposure starts.
If [2nd curtain] is set, the flash will fire right before the exposure
ends. When this is combined with a slow sync speed, you can create
a trail of light such as from car headlights at night. With 2nd-curtain
sync, a prefiash is fired when you press the shutter button
completely. This is to determine the exposure. Then immediately
before the exposure ends, the real flash is fired. Therefore, two
flashes will be fired. However, with shutter speeds faster than 1/30
sec., 1st curtain sync will automatically take effect.
If an external Speedlite is attached, you can also set [Hi-speed]. For
details, see the Speedlite's instruction manual.
Flash exposure compensation
See "t_ Flash Exposure Compensation"
on page 102.
E-TTL II flash metering
For normal flash exposures, set it to [Evaluative]. [Average] is for
advanced users. As with an external Speedlite, the metering area is
averaged. Flash exposure compensation may be necessary.
Clear flash settings
On the [External flash func. setting] screen, press the < DISP.>
button to display the screen to clear the flash settings. When you
select [OK], the settings for the built-in
Speedlite will be cleared.
flash and external
169
Setting the Flash*
The Custom Functions displayed under [External
will vary depending on the Speedlite model.
flash C.Fn setting]
Display the Custom
Function.
Select [External flash C.Fn setting],
then press <_-_>.
Set the Custom
Function.
Press the < 4_ > key to select the
function number, then set the
function. The procedure is the same
as setting the camera's Custom
Functions (p.216).
To clear all the Custom Function
settings, select [Clear ext. flash C.Fn
set.] in step 1.
17O
Appending
Dust Delete Data*
Dust entering the camera can adhere to the image sensor and cause
dust spots to be visible on the captured images. To erase these dust
spots, you can append the Dust Delete Data to the images. The Dust
Delete Data is used by Digital Photo Professional
p.270) to erase the dust spots automatically.
(provided software,
Get a solid-white object (paper, etc.).
Set the lens focal length to 50mm or longer.
Set the lens focus mode switch to <MF> and set the focus to infinity
(co). If the lens has no distance scale, look at the front of the lens and
turn the focusing ring clockwise all the way.
Select
[Dust
Delete
Data].
Under the [t_] tab, select [Dust
Delete Data], then press < _-_>.
Select
EOK].
Select [OK], then press < _-_>.
instructions will appear.
171
Appending Dust Delete Data*
Photograph
[3
B
[3
D
[3
B
[3
[3
a solid=white
object.
At a distance of 20 cm - 30 cm (0.7 ft.
- 1.0 ft.), fill the viewfinder with a
patternless, solid-white object and
take a picture.
The picture will be taken in aperturepriority AE mode at an aperture of
f/22.
Since the image will not be saved, the
data can still be obtained even if there
is no card in the camera.
When the picture is taken, the camera will
start collecting the Dust Delete Data.
When the Dust Delete Data is obtained, a
message will appear.
Select [OK], and the menu will reappear.
If the data was not obtained
successfully, a message to that effect
will appear. Follow the "Preparation"
procedure on the preceding page, then
select [OK]. Take the picture again.
After the Dust Delete Data is obtained, it is appended to all the JPEG
and RAW images captured thereafter. Before an important shoot, you
should update the Dust Delete Data by obtaining it again.
For details about using Digital Photo Professional (provided software,
p.270) to erase dust spots, see the Software Instruction Manual (p.272)
in the Software Instruction Manual CD-ROM.
The Dust Delete Data appended to the image is so small that it hardly
affects the image file size.
Be sure to use a solid-white object such as a new sheet of white paper. If the
paper has any pattern or design, it may be recognized as dust data and
affect the accuracy of the dust deletion with the software.
172
Manual
Sensor
Cleaning _
if dust adhere to the image sensor and dust spots appear on the
images, you can clean the image sensor yourself with a camera blower.
The surface of the image sensor is extremely delicate. If the
sensor needs to be cleaned directly,
Service Center is recommended.
having
it done by a Canon
Before cleaning the sensor, detach the lens from the camera.
Select
[Clean
manually].
Under the [_:] tab, select [Clean
manually], then press < _-_>.
Select
[OK].
Select [OK], then press <_-_>.
in a moment, the reflex mirror will
Iockup and the shutter will open.
Clean the sensor.
End the cleaning.
Set the power switch to < OFF>.
For the power source, using AC Adapter Kit ACK-E10 (sold separately)
is recommended.
Ufyou use a battery, make sure it is fully recharged.
173
Manual Sensor Cleaning*
,
,
,
174
While cleaning the sensor, never do any of the following,
if the
power is cut off, the shutter will close and the shutter curtains and
image sensor might get damaged.
* Setting the power switch to <OFF>.
* Opening the card/battery
compartment
cover.
The surface of the image sensor is extremely delicate. Clean the sensor
with care.
Use a plain blower without any brush attached. A brush can scratch the
sensor.
Do not insert the blower tip inside the camera beyond the lens mount. If
the power is turned off, the shutter will close and the shutter curtains or
reflex mirror might get damaged.
Never use canned air or gas to clean the sensor. The blowing force can
damage the sensor or the spray gas can freeze on the sensor.
If the battery level becomes low while you clean the sensor, the beeper
will sound as a warning. Stop cleaning the sensor.
If a smudge that cannot be removed with a blower remains, having the
sensor cleaned by a Canon Service Center is recommended.
image Playback
This chapter explains features related to viewing photos
and movies, going into more detail than in Chapter 2
"Basic Shooting and Image Playback." Here you will
find explanations about how to playback and erase
photos and movies with the camera and viewing them
on a TV set.
About
images
taken
with
another
camera:
The camera might not be able to properly display images captured
with a different camera or edited with a computer or whose file name
was changed.
[]
Searching for images Quickly
Search for images quickly with the index display showing four or nine
images on one screen.
Playback
the image.
When you press the < [] > button, the
last image captured will be displayed.
Switch to the index display.
Press the <[].(_>
button.
The 4-image index display will
appear. The currently-selected
image
will be highlighted in a blue frame.
Press the <[].Q>
button again to
switch to the 9-image index display.
Pressing the <_,> button will switch
the display between 9 images, 4
images and one image displayed.
Select
an image.
Press the < ,;_> key to move the blue
frame to select an image.
Turning the <_>
dial will display the
next screen or previous image.
Press <_-_> and the selected image
will be displayed as a single image.
176
[]
Searching for Images Quickly
With the single image display, you can turn the <_>
dial to jump
through the images forward or back according to the jump method that
was set.
Select
[image
jump
w/_¢_].
Under the [_:] tab, select [Image
jump w/_],
then press <8>.
Se]eot
thejumpmet.od
Press the < ,;_> key to select the
jump method, then press <8>.
.¢1: Display images one by one
.._: Jump 10 images
.._: Jump 100 images
.._ : Display
.._: Display
: Display
by date
by folder
movies only
.._: Display stills only
.._: Display by image rating (p.180)
Turn the <_>
dial to select the
rating.
:'_ii Browse
by jumping.
Press the <l_q> button to playback
Jump
images.
On the singleqmage
<_>
dial.
method
Playback
display, turn the
position
To search images accordingto the shooting date, select [Date].
To search images accordingto folder, select [Fomder].
If the card contains both [Movies] and [Stills], select either one to
display only movies or stills.
If no images match the selected [Rating], browsing through the images
with <_>
is not possible.
177
/_
Magnified
View
You can magnify a shot image by 1.5x to 10x on the LCD monitor.
Magnify
the image.
During image playback, press the
< _ > button.
The image will be magnified.
If you hold down the < _ > button, the
image will be magnified until it
reaches the maximum magnification.
Press the <[].Q>
button to reduce
the magnification. If you hold down
the button, the magnification will be
reduced to the single image display.
Magnified
area position
Scroll
around
the image.
Use the < ,;,> key to scroll around the
magnified image.
To exit the magnified display, press
the < [] > button and the single image
display will return.
,
,
,
178
You can turn the <._%> dial to view another image while the
magnification is maintained.
The image cannot be magnified during the image review immediately
after shooting.
A movie cannot be magnified.
@ Rotating
the image
You can rotate the displayed image to the desired orientation.
Select
[Rotate].
Under the [_'] tab, select [Rotate],
then press <_-_>.
Select
:iii!!:
an image.
Press the <_>
key to select the
image to be rotated.
You can also select an image on the
index display (p.176).
Rotate
the image.
Each time you press <_-_>, the
image will rotate clockwise as follows:
90 ° -_ 270 ° --> 0 o
To rotate another image, repeat steps
2 and 3.
To exit and return to the menu, press
the <MENU> button.
If you have set [_f" Auto rotate] to [On_ _l] (p.162) before taking
vertical shots, you need not rotate the image as described above.
If the rotated image is not displayed in the rotated orientation during
image playback, set [_" Auto rotate] to [On _ _l].
A movie cannot be rotated.
179
Setting
Ratings
You can rate images and movies with one of five rating marks: I--3t1-*-3t
[:JI[:*]l[:*:].
, Seleot
[Rati.g:].
Under the [_:] tab, select [Rating],
then press <_-_>.
Select
an image
or movie.
Press the < _
> key to select the
image or movie to be rated.
You can display three images by
pressing the <_._>
button. To
return to the single-image display,
press the < ¢, > button.
Rate the
image
or movie.
Press the < AT > key to select a rating
mark.
The total number of images and
movies rated will be counted for each
rating.
To rate another image or movie,
repeat steps 2 and 3.
To exit and return to the menu, press
the <MENU> button.
18O
Setting Ratings
L_
The number next to the rating marks ([,31[**]1[***]1[***]/[*****])
can only go up to
999. If there are 1,000 or more images for a rating, [###] will be displayed.
Taking advantage
of ratings
With the [3: Image jump w/_]
option, you can display only the rated
images and movies.
, With the [3: Slide show] option, you can playback only the rated
images and movies.
, With Digital Photo Professional (provided software, p.270), you can
select only the rated images and movies.
With Windows Vista and Windows 7, you can see the rating with the file
information display or the provided image viewer.
181
[]
Quick Control
During Playback
When you press the <[]> button during image playback, you can set
the following: [o_ Protect images, __ Rotate, _ Rating, .._ Image
jump w/_].
Note that movies cannot be rotated (__ Rotate).
Press the
< []
> button.
During image playback, press the
< [] > button.
The functions settable with Quick
Control will appear on the left of the
screen.
Seleot
ofunotion
ond,etit.
Press the <AT> key to select a
function.
The name and current setting of the
selected function are displayed at the
bottom.
Set it by pressing the <4_*>
key.
Exitthe,e ing.
Press the < [] > button to turn off the
Quick Control icons and function
settings.
To rotate an image, set [_'" Auto rotate] to [On_
_].
ff [_'" Auto rotate] is
set to [On_]
or [Oft], the [__- Rotate] setting will be recorded to the image,
but the camera will not rotate the image for display.
182
[] Quick Control During Playback
Pressing the <[]_]> button during the index display will switch to the
single-image display and the Quick Control icons will appear. Pressing
the <_]> button again will return to the index display.
For images taken with another camera, selectable functions may be
limited.
183
Enjoying Movies
Basically,
you can
playback
movies
in the following
three
ways:
p,91>
An HDMI
cable
(sold
separately)
is
necessary
to connect
the camera to a
TV set. The TV set must also have an
[_
_-
_--_" -
"
HDMI
terminal,
When
the camera
is connected
to a TV
playback
movies and still photos on the
set with an HDMI cable, you can
TV set. If you use a High-Definition
TV
set to playback
movies
watch
High-Definition
shot with
the movies
this camera,
(HD)
you can
in high definition.
The camera does not have an audio/video OUT terminal. Therefore,
camera cannot be connected to a TV set with an analog AV cable.
the
Movies on a card can be played only by devices compatible with MOV
files.
Since hard disk recorders do not have an HDMI IN terminal, the camera
cannot be connected to a hard disk recorder with an HDMI cable.
Even if the camera is connected to a hard disk recorder with a USB
cable, movies and still photos cannot be played nor saved.
Using HDMI Cable HTC-100 (sold separately)
184
is recommended.
_,;l, Enjoying
You can
camera's
Movies
playback
movies on the
LCD monitor. You can also edit
out the movie's
first and last scenes,
playback
the images
card in an automatic
and movies
slide show.
and
in the
_J_ A movie edited with a personal computer cannot be rewritten to the card and
played back with the camera.
(See the PDF file instruction manual for ZoomBrowser EX/ImageBrowser, p.272)
The movie files recorded in the card can
be transferred to a personal computer
and played or edited with ZoomBrowser
EX/ImageBrowser
(provided software,
p.270).
You can also extract a single frame from
a movie and save it as a still photo.
d_
,
To have the movie playback smoothly on a personal computer, use a
high-performance personal computer. Regarding the computer hardware
requirements for ZoomBrowser
instruction manual.
EX/ImageBrowser,
see the PDF file
If you want to use commercially-available
software to playback or edit the
movies, be sure it is compatible with MOV files. For details on
commercially-available
software,
inquire the software
maker.
185
Playing Movies
P|ayback the image.
Press the <l_q> button to display
images.
Select
amovie.
Press the <41_> key to select
a
movie.
On the single-image display, the
<_,_=,
_ii>
icon displayed on the
upper left indicates a movie.
On the index display, the perforation
on the left edge of the image
indicates a movie. As movies
cannot be played on the index
display, press <_-_> to switch to
the single=image display.
i_,_ On the single=image
press <_>.
display,
The movie playback panel will appear
on the bottom.
Playback
the movie.
Select [_] (Play), then press <_>.
The movie will start playing.
You can pause the movie playback by
Speaker
pressing <8>.
During movie playback, you can turn
the < _>
dial to adjust the buiff-in
speaker's sound volume.
For more details on the playback
procedure, see the next page.
186
",_, Playing Movies
Function
Playback
Exit
Returns
Play
Pressing
I_- Slow motion
First
frame
4JJ Previous
JJ_ Next frame
Last frame
_( Edit
ram'
ss"
,_l_lVolume
<C)>
toggles
display.
between
play and stop.
Adjust the slow motion speed by pressing the < 4_ >
key. The slow-motion
speed is indicated on the upper
right.
Displays
frame
Description
to the single-image
the movie's
first frame.
Each time you press <Q>,
a single
is displayed, if you hold down <C)>,
movie.
previous frame
it will rewind the
Each time you press <C)>, the movie will play frameby-frame.
If you hold down < _>,
it will fast forward
the movie.
Displays
the movie's
Displays
the editing
last frame.
screen
(p.188).
Playback
position
Playback
time (minutes:seconds)
You can adjust the built-in speaker's
volume by turning the <_>
dial.
(p.186)
sound
With a fully-charged Battery Pack LP-E10, the continuous playback time
at 23°C/73°F wilt be as follows: Approx. 4 hr.
During the single-image display, you can press the <DISR> button to
change the display format (p.199).
ff you connect the camera to a TV set (p.184, 191 ) to playback a movie,
adjust the sound volume with the TV set. (Turning the < _ > dial will not
adjust the sound volume.)
This camera cannot playback Full High-Definition (Full HD) or HighDefinition (HD) movies (60/50 fps frame rate) taken with another EOS
camera. This camera can only playback High-Definition (HD) and
Standard-Definition
(SD) movies having a 30/25 fps frame rate.
187
Editing a Movie's First and Last Scenes
You can edit out the first and last scenes of a movie in 1-sec. increments.
On the
select
movie
playback
screen,
[_].
The editing screen will be displayed.
Specify
the part to be edited
out.
Select either [_] (Cut beginning)
[_] (Cut end), then press <8>.
or
Press the <41_> key to see the
previous or next frames. Holding it
down will fast forward the frames.
After deciding which part to edit out,
press <8>.
The portion highlighted
in blue on the top of the screen is
what will remain.
Check
the edited
movie.
Select [1_] and press < _ > to playback
the portion highlighted in blue.
To change the editing, go back to step 2.
To cancel the editing, select [_] and
press < _-_ >.
Save
themovie.
Select [[L_], then press <_>.
The save screen will appear.
To save it as a new movie, select
[New file]. To save it and overwrite
the original movie file, select
[Overwrite]. Then press <_-_>.
,
188
Since the editing is done in 1-sec. increments (position indicated by
[_]), the exact position where the movie is edited may differ slightly from
the position you specified.
If the card does not have enough room, [New file] wilt not be selectable.
More movie editing functions are available with ZoomBrowser EXJ
ImageBrowser (provided software, p.270).
Slide Show (Auto Playback)
You can playback
the images
in the card
Select
as an automatic
[Slide
slide
show.
show].
Under the [_:] tab, select [Slide
show], then press <_-_>.
Number
of,mo0e,
tobe
p,ayedSelect
the images
to be played.
Press the <AT> key to select the
desired option, then press <_-_>.
[All
imageslMovieslStills]
Press the <AT> key to select one of the
following: [_AII
images/D_ Movies/
aStills].
Then press <_-_>.
[Date/Folder/Rating]
Press the <AT> key to select one of
the following: [_Date/mFolder/
Rating].
When < _'J_ _> is highlighted,
press the <DISP.> button.
Press the < AT > key to select the
desired option, then press <_-_>.
item
@All
images
Playback Description
All the still photos and movies in the card will be played back.
[] Date
Still photos and movies taken on the selected shooting date wilt
be played back.
mFolder
Still photos and movies in the selected folder will be played back.
_ Movies
Only the movies in the card will be played back.
_Stiils
Only the still photos in the card will be played back.
Rating
Only the still photos and movies with the selected rating will be
played back.
189
Slide Show (Auto Playback)
Set [Set
up] as desired.
Press the <AT> key to select [Set
up], then press <_-_>.
Set the [Display time] (still photos),
[Repeat], and [Transition effect].
Then press the <MENU> button.
[Display
time]
[Repeat]
[Transition
effect]
Start the slide show.
Press
then
the < AT > key to select
press
[Start],
<_-_>.
After [Loading
image...]
the slide show will start.
is displayed,
Quit the slide show.
Toquit the slide show and return to
the setting screen, press the
<MENU> button.
To pause the slide show, press <_"_>. During pause, [||] wilt be
displayed on the upper left of the image. Press <_"_> again to resume
the slide show.
,
,
During auto playback, you can press the <DISR> button to change the
still photo display format (p.70).
During movie playback, you can adjust the sound volume by turning the
<_>
dial.
During pause, you can press the <41_> key to view another image.
During the slide show, auto power off will not take effect.
The display time may vary depending on the image.
To view the slide show on a TV set, see pages 191-193.
190
Playback
on a High=Definition
TV
An HDMI cable (sold separately) is necessary to connect the
camera to a TV set. The TV set must also have an HDMI terminal.
When the camera is connected to a TV set with an HDMI cable, you can
playback movies and still photos on the TV set. If you use a HighDefinition TV set to playback High-Definition (HD) movies shot with this
camera, you can watch the movies in high definition.
Connect
the
HDMI
cable
to the
camera,
With the plug's <AHDMI MINI> logo
facing the front of the camera, insert it
into the <HDMI OUT> terminal.
Connect the HDMI cable to the TV
set.
Connect the HDMI cable to the TV's
HDMI IN port.
Turn on the TV and switch the
TV's video input to select the
connected port.
,,:_i Set the camera's
power
switch
to
<ON>.
' Adjust the movie's sound volume with the TV set. The sound volume
cannot be adjusted with the camera.
Before connecting or disconnecting the cable between the camera and
television, turn off the camera and TV set.
Depending on the TV set, part of the image displayed might be cut off.
191
Playback
on a High-Definition
TV
2;¸ Press
the
<[_>
button.
The image wiii appear on the TV
screen (Nothing will be displayed on
the camera's LCD monitor).
The images will automatically be
displayed at the TV's optimum
resolution.
By pressing the <DISP.> button, you
can change the display format.
To playback movies, see page 186.
;, Do not connect any other device's output to the camera's <HDMI
terminal. Doing so may cause a malfunction.
Certain TVs might not be able to playback the captured images.
OUT>
if the TV set connected to the camera with an HDMI cable is compatible
with HDMI CEC*, you can use the TV set's remote control for playback
operations.
* An HDMI-standard function enabling HDMI devices to control each other so that
you can control them with one remote control unit.
l
Set [Ctrl
over
HDMI]
to [Enable].
Under the [_:] tab, select [Ctrl over
HDMI], then press <_-_>.
Select [Enable], then press <8>.
Connect
......
,,£
the camera
to a TV set.
Use an HDMI cable to connect the
camera to the TV.
The TV's input will switch
automatically to the HDMI port
connected to the camera.
192
Playback
on a High-Definition
TV
Press the camera's
<r_>
button.
An image will appear on the TV
screen and you can use the TV's
remote control to playback images.
Select an image or movie.
Point the remote control toward the
TV set and press the ,-t--* button to
select an image.
st,..oto.toyboo,
moo,,
remote
control's
Enter
button.
• Return
The menu appears and you can do
the playback operations shown on the
left.
Press the ,-/--* button to select the
• 9-image index
• Play movie
• Slide show
desired option, then press the Enter
button. For a slide show, press the
remote control's t/$ button to select
Movie playback
_
Press the
menu
DISP, • Disp. shooting info
@
• Rotate
an option, then press the Enter
button.
If you select [Return] and press the
Enter button, the menu will disappear
and you can use the ,-/--* button to
select an image.
Some TV sets require you to first enable the HDMI CEC connection. For
details, see the TV set's instruction manual.
Certain TV sets, even those compatible with HDMI CEC, may not
operate properly. In such a case, disconnect the HDMI cable, set [3:
Ctrl over HDMI] to [Disable], and use the camera to control the
playback operation.
193
]
Protecting images
Protecting an image prevents it from being erased accidentally.
Select
[Protect
images].
Under the [_'] tab, select [Protect
images], then press <8>.
The protect setting screen will
appear.
Select
[Select
images].
Select [Select images], then press
< _'_
,maoe
proteot
,ooo Protect
>.
the image.
Press the <-,I_ > key to select the
image to be protected, then press
<8
> .
When an image is protected, the
<1_> icon will appear on the top of
the screen.
To cancel the image protection, press
<8>
again. The <[B> icon will
disappear.
To protect another image, repeat step
3.
To exit the image protection, press
the <MENU> button. The menu will
reappear.
194
[]
Protecting Images
You can protect all the images in a folder or card at one time.
When you select [All images in folder]
or [All images on card] in [3" Protect
images], all the images in the folder or
card will be protected.
To cancel the image protection, select
[Unprotect all images in folder] or
[Unprotect all images on card].
if you format
the card (p.44), the protected
images will also be erased.
Movies can also be protected.
Once an image is protected, it cannot be erased by the camera's erase
function. To erase a protected image, you must first cancel the
protection.
If you erase all the images (p.197), only the protected images will
remain. This is convenient when you want to erase unnecessary images
all at once.
195
Erasing images
You can either select and erase images one by one or erase them in
one batch. Protected images (p.194) will not be erased.
Once an image is erased, it cannot be recovered. Make sure
you no longer need the image before erasing it. To prevent
important images from being erased accidentally, protect
them. Erasing a Iff_+_ L image will erase both the _
and
ill L images.
Playback the image to be erased.
Press the
< @ > button.
The erase dialog will appear at the
bottom of the screen.
Erase
the
image.
Select [Erase], then press < _-_ >. The
image displayed will be erased.
By checkmarking the images to be erased, you can erase multiple
images at one time.
Select [Erase images].
Under the [_'] tab, select [Erase
images], then press <_-_>.
196
Erasing Images
Select
[Select
and erase
images].
Select [Select and erase images],
then press <_>.
The images will be displayed.
To display the three-image display,
press the < []._ > button. To return to
the single-image display, press the
< ¢, > button.
Select the images to be erased.
Press the <41_> key to select the
image to be erased, then press the
<AT> key.
A <_/> checkmark will be displayed
on the upper left.
To select other images to be erased,
repeat step 3.
Erase the
images.
Press the <-_> button.
Select [OK], then press <_-_>.
The selected images will be erased.
You can erase all the images in a folder or card at one time. When [3"
Erase images] is set to [All images in folder] or [AH images on card],
all the images in the folder or card will be erased.
To also erase protected
images, format the card (p.44).
197
DISR Shooting
Exposure compensation
Information
amount .............
Display
.................
Protect
..................
Rating
Flash exposure
compensation amount
Folder number - File number
Aperture
Histogram
Shutter speed
(Brightness/RGB)
Metering mode
Shooting
mode
White balance
space
date and
Image-recording
quality
time
Playback number/
Total images recorded
Eye-Fi transmission
White
balance correction
.................
................
File size
* With _+d[.
images, the _
file size is displayed.
* Photos taken with flash without any flash exposure compensation are marked
with the <_ > icon. Photos taken with flash exposure compensation are marked
with the <_>
icon.
198
DISR Shooting Information Display
Shooting mode ....
ambience effects
....Lighting or scene
* For images taken in Basic Zone modes, the information
depending on the shooting mode.
* Photos taken in the <_>
mode will show [Background
displayed may differ
blur].
Shooting time .......................
Movie shooting
mode
Recording
system
Movie recording size
file size
.......................................
Frame rate
* The shutter speed, aperture, and ISO speed will not be displayed.
199
DISP.Shooting Information Display
About the Highlight Alert
When the shooting information is displayed, any overexposed areas of the
image will blink. To obtain more image detail in the overexposed areas, set
the exposure compensation to a negative amount and shoot again.
About the Histogram
The brightness histogram shows the exposure level distribution and
overall brightness. The RGB histogram is for checking the color
saturation and gradation. The display can be switched with [3:
Histogram].
[Brightness]
Display
This histogram is a graph showing the distribution of
the image's brightness level. The horizontal axis
indicates the brightness level (darker on the left and
brighter on the right), while the vertical axis indicates
how many pixels exist for each brightness level. The
more pixels there are toward the left, the darker the
image. And the more pixels there are toward the right,
the brighter the image. If there are too many pixels on
the left, the shadow detail will be lost. And if there are
too many pixels on the right, the highlight detail will be
lost. The gradation in-between will be reproduced. By
checking the image and its brightness histogram, you
SampleHistograms
Darkimage
Normalbrightness
Bright image
can see the exposure level inclination and the overall gradation.
[RGB] Display
This histogram is a graph showing the distribution of each primary color's
brightness level in the image (RGB or red, green, and blue). The horizontal
axis indicates the color's brightness level (darker on the left and brighter on
the right), while the vertical axis indicates how many pixels exist for each
color brightness level. The more pixels there are toward the left, the darker
and less prominent the color. And the more pixels there are toward the right,
the brighter and denser the color. If there are too many pixels on the left, the
respective color information will be lacking. And if there are too many pixels
on the right, the color will be too saturated with no detail. By checking the
image's RGB histogram, you can see the color's saturation and gradation
condition and white balance inclination.
200
CANON
USA
iNC. 30-2, Shimomamko
--
CANON
U.S.A.
3-chome,
Ohta-ku, Tokyo t46-850t,
Japan
iNC.
One Canon Plaza, Lake Success, NY 11042-1198, U.SA.
For all inquires concerning
this product, call to}l free in the U S
1-800-OK-CANON
CANADA
--
CANON
CANADA
_NC. HEADQUARTERS
6390 Dixie Road, Mississauga,
Ontario LST 1P7, Canada
CANON CANADA
_NC. MONTREAL
BRANON
5990, C6te-de-Liesse,
Montr6al Quebec H4T 1V7, Canada
CANON CANADA
INC. CALGARY
OFFICE
2828, 16th Street, N.E Calgary, Alberta
For all inquiries concerning
this product,
1-800-OK-CANON
EUROPE,
--
AFRICA &
MIDDLE EAST
CANON
EUROPA
T2E 7K7, Canada
cal_ toll free in Canada
N.Y.
Bovenkerkerweg
59-61, 1185 XB AmsteNeen,
CANON FRANCE S.AS.
17,Quai
CANON
du President
UK LTD.
Paul Doumer,
Woodhatch
Reigate,Surrey
CANON DEUTSCNLAND
The Netherlands
92414 Courbevoie
RN2 8BF, United
ambN
Cedex,
France
Kingdom
Europark Fichtenhain
A10, 47807 Krefeld, Germany
CANON iTALIA S.p,A=
Via Milano 8, 20097 San Donato Milanese, (MI), Italy
CANON Schweiz
A.G.
Industriestrasse
12, 8305 DieSikon, Switzerland
Canon GmbN
Zetschegasse
11 A-1230 Vienna, Austria
CANON Espa_a,S.A.
Av. De Europa,6 Aicobendas
28108 Madrid,
CANON Portugal
S.A.
Run Alfredo da Silva,14
AIfragide
2610-016
Spain
Arnadora,
Portugal
CENTRAL & -SOUTH AMERICA
CANON LATIN AMERICA,
INC.
703 Waterford Way. Suite 400 Miami,
ASiA
CANON (China} Co., LTD.
15F Jinbao Building No.89 Jinbao Street, Dongcheng
District, Beijing 100005, China
CANON NONGKONG
CO., LTD.
19/F, The Metropolis Tower, 10 Metropolis Drive, Hunghom, Kow}oon, Hong Nong
CANON SINGAPORE
PTE. LTD.
--
FL 33126,U
S A
I HarbourFront
Avenue, #04-01 Neppel Bay Tower, Singapore
CANON KOR_=A CONSUMER
IMAGING INC.
Gangnam
OCEANIA
--
CANON
Finance
Center 17F, 737Jeoksam-Dong,
AUSTRALIA
JAPAN
--
Business
Seoul,
135-984,
Korea
PTY. LTD.
I Thomas Holt Drive, North Ryde, Sydney
CANON NEW ZEALAND
LTD.
Akoranga
098632
Gangnam-Gu,
Park, Akoranga
NSW
2113, Australia
Drive, Northcote,
CANON !_ARKETING
JAPAN
INC.
16-6, Kohnan 2-chome,
Minato-ku, Tokyo
108-8011,
Auckland,
New Zealand
Japan
"1
This Instruction Manual booklet is current as of January 2011. For information on |
the camera's compatibility with any accessories and lenses introduced after this
date, contact any Canon Service Center.
/
CTI-7194HE-001
© CANON INC. 2011
Download PDF

advertising