Canon | EF 70-200mm f/2.8L IS II USM | Specifications | Canon 2751B002 Camera Accessories User Manual

EF70-200mm f/2.8L IS II USM
C
Y
P
O
ENG
Instruction
Thank you for purchasing a Canon product.
Dedicated to EOS cameras, the Canon EF70200mm f/2.8L IS II USM lens is a highperformance telephoto zoom lens equipped
with an Image Stabilizer.
• “IS” stands for Image Stabilizer.
• “USM” stands for Ultrasonic Motor.
C
Conventions used in this instruction
Warning to prevent lens or camera malfunction
or damage.
Features
1. The Image Stabilizer gives the equivalent
effect of a shutter speed four stops faster*.
2. With fluorite and UD lens elements,
outstanding image delineation is obtained.
3. Ultrasonic motor (USM) for quick and quiet
autofocusing.
4. Manual focusing is available after the subject
comes into focus in autofocus mode (ONE
SHOT AF).
5. A truly round aperture hole results in a nicer
background blur.
6. The lens is compatible with Extender EF1.4X ll
and EF2X ll.
7. Tight seal structure ensures excellent dustproof and drip-proof performance.
Y
P
O
* Based on [1/focal length] second. Generally, it requires
a shutter speed [1/focal length] second or faster to
prevent camera shake.
Supplementary notes on using the lens and
taking pictures.
ENG-1
a Safety Precautions
a Safety Precautions
• Do not look at the sun or a bright light source
through the lens or camera. Doing so could result
in loss of vision. Looking at the sun directly through
the lens is especially hazardous.
• Do not point the lens or camera at the sun or
photograph it. This is because the lens
concentrates the sun’s rays even when the sun is
outside the image area or when shooting with
backlight, which could cause malfunction or fire.
• Whether it is attached to the camera or not, do not
leave the lens under the sun without the lens cap
attached. This is to prevent the lens from
concentrating the sun’s rays, which could cause a fire.
Handling Cautions
C
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Do not make any changes or modifications to the equipment
unless otherwise specified in the instructions. If such changes or
modifications should be made, you could be required to stop
operation of the equipment.
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for
help.
Y
P
O
• If the lens is taken from a cold environment into
a warm one, condensation may develop on the
lens surface and internal parts. To prevent
condensation in this case, first put the lens into an
airtight plastic bag before taking it from a cold to
warm environment. Then take out the lens after it
has warmed gradually. Do the same when taking
the lens from a warm environment into a cold one.
• Do not leave the lens in excessive heat such as in
a car in direct sunlight. High temperatures can
cause the lens to malfunction.
This Class B digital apparatus complies with Canadian ICES-003.
ENG-2
Nomenclature
Focusing distance range selection switch (→ 5)
Distance scale (→ 11)
Hood mount (→ 7)
Zoom ring (→ 6)
Filter mounting
thread (→ 13)
C
Y
P
O
Rubber ring (→ 4)
Contacts (→ 4)
Focusing ring (→ 5)
Lens mount index (→ 4)
Focus mode switch (→ 5)
Image stabilizer switch (→ 8)
Image stabilizer mode selector switch (→ 8)
Tripod mount (→ 12)
Orientation lock knob (→ 12)
For detailed information, reference page numbers are provided in parentheses (→ **).
ENG-3
1. Mounting and Detaching the Lens
See your camera’s instructions for details on
mounting and detaching the lens.
The lens mount has a rubber ring for enhanced
water- and dust-resistance. The rubber ring may
cause slight abrasions around the camera's lens
mount, but this will not cause any problems. If the
rubber ring becomes worn, it is replaceable by a
Canon Service Center at cost.
Y
P
O
• After detaching the lens, place the lens with the
rear end up to prevent the lens surface and
electrical contacts from getting scratched.
• If the contacts get soiled, scratched, or have
fingerprints on them, corrosion or faulty
connections can result. The camera and lens
may not operate properly.
• If the contacts get soiled or have fingerprints on
them, clean them with a soft cloth.
• If you remove the lens, cover it with the dust
cap. To attach it properly, align the lens mount
index and the K index of the dust cap as shown
in the diagram, and turn clockwise. To remove it,
reverse the order.
C
ENG-4
2. Setting the Focus
Mode
3. Switching the Focusing
Distance Range
Y
P
O
To shoot in autofocus (AF) mode, set the focus
mode switch to AF.
To use only manual focusing (MF), set the focus
mode switch to MF, and focus by turning the
focusing ring. The focusing ring always works,
regardless of the focus mode.
C
You can set the focusing distance range to
1.2 m/3.9 ft. to infinity or 2.5 m/8.2 ft. to infinity.
By setting the suitable focusing distance range,
the actual autofocusing time can be shorter.
After autofocusing in ONE SHOT AF mode, focus
manually by pressing the shutter button halfway
and turning the focusing ring. (Full-time manual
focus)
ENG-5
4. Zooming
To zoom, turn the zoom ring.
Be sure to finish zooming before focusing.
Zooming after focusing can affect the focus.
C
Y
P
O
ENG-6
5. Hood
The ET-87 hood can keep unwanted light out of the lens, and also protects the front of the lens from
rain, snow, and dust.
Attaching
C
Y
P
O
To attach the hood, align the hood’s attachment
position mark with the red dot on the front of the
lens, then turn the hood as shown by the arrow
until the lens' red dot is aligned with the hood's
stop position mark.
Button
Removing
To remove the hood, hold down the button on the
side and turn the hood in the direction of the
arrow until the position mark on the hood aligns
with the red dot.
The hood can be reverse-mounted on the lens
for storage.
• Part of the picture may be blocked if the hood is not attached properly.
• When attaching or detaching the hood, grasp the base of the hood to turn it. To prevent deformation, do not
grasp the rim of the hood to turn it.
ENG-7
6. Image Stabilizer Settings
You can use the image stabilizer in AF or MF mode.
Set the STABILIZER switch
to
.
• If you are not going to use the
image stabilizer function, set
the switch to
.
Y
P
O
Select the stabilizer mode.
• MODE 1: Corrects vibrations
in all directions. It is mainly
effective for shooting still
subjects.
• MODE 2: It compensates for
vertical camera shake during
following shots in a horizontal
direction, and compensates for
horizontal camera shake
during following shots in a
vertical direction.
C
When you press the shutter
button halfway, the Image
Stabilizer will start
operating.
• Make sure the image in the
viewfinder is stable, then press
the shutter button the rest of
the way down to take the
picture.
ENG-8
7. Tips on Using the Image Stabilizer
The image stabilizer in this lens is effective for hand-held shots under the following conditions.
● MODE 1
● MODE 2
C
Y
P
O
• In semi-darkened areas such as indoors or
outdoors at night.
• In locations where flash photography is
prohibited, such as art museums and theater
stages.
• In situations where your footing is uncertain.
• In situations where fast shutter settings cannot
be used.
• When panning subjects in motion.
ENG-9
Tips on Using the Image Stabilizer
• The Image Stabilizer cannot compensate for a
blurred shot caused by a subject that moved.
• Set the STABILIZER switch to
when you are
taking pictures using the Bulb setting (long
exposures). If the STABILIZER switch is set to
,
the image stabilizer function may introduce errors.
• The Image Stabilizer might not be fully effective
in the following cases:
• You shoot while riding on a bumpy road.
• You move the camera dramatically for a
panning shot in Mode 1.
• You shoot using techniques other than
following shots in Mode 2.
• The Image Stabilizer consumes more power
than normal shooting, so fewer shots can be
taken if you use the function.
• The image stabilizer operates for about two
seconds even when your finger is off the shutter
button. Do not remove the lens while the stabilizer
is in operation. This will cause a malfunction.
• With the EOS-1V/HS, 3, ELAN 7E/ELAN
7/30/33, ELAN 7NE/ELAN 7N/30V/33V, ELAN
II/ELAN IIE/50/50E, REBEL 2000/300, IX, and
D30, the Image Stabilizer will not work during
self-timer operation.
C
• Using a tripod also stabilizes the image.
However, depending on the kind of tripod and
shooting conditions, sometimes it may be better
to turn off the Image Stabilizer function.
• The stabilizer is equally effective for hand-held
photography and photography with a monopod.
• The Image Stabilizer function also operates
when the lens is used with the EF12 II/EF25 II
Extension Tube, and the EF1.4X II/EF2X II
Extender.
• Pictures may look distorted after being taken
depending on the camera, but this doesn't affect
shooting.
• If you set the camera’s Custom Function to
change the assigned button to operate the AF,
the Image Stabilizer will operate when you press
the newly assigned AF button.
Y
P
O
ENG-10
8. Infinity Compensation Mark
9. Infrared Index
Infinity compensation mark
Distance index
Y
P
O
To compensate for shifting of the infinity focus
point that results from changes in temperature.
The infinity position at normal temperature is the
point at which the vertical line of the L mark is
aligned with the distance indicator on the
distance scale.
C
For accurate manual focusing of subjects at
infinity, look through the viewfinder or look at the
magnified image* on the LCD screen while
rotating the focusing ring.
* For cameras with Live View shooting capability.
The infrared index corrects the focus setting when using
monochrome infrared film. Focus on the subject
manually, then adjust the distance setting by moving the
focusing ring to the corresponding infrared index mark.
Some EOS cameras cannot use infrared film. See
the instructions for your EOS camera.
• The infrared index position is based on a
wavelength of 800 nm.
• The compensation amount differs depending on
the focal length. Use the indicated focal length as
a guide when setting the compensation amount.
• Be sure to observe the manufacturer’s
instructions when using infrared film.
• Use a red filter when you take the picture.
ENG-11
10. Using the Tripod Mount
Adjusting the Revolving Mount
You can loosen the orientation lock-knob on the tripod mount to allow it to rotate as needed to fit a
particular camera model for switching between vertical and horizontal positions.
Detaching
First remove the lens from the camera and then remove the tripod mount from the lens as shown
below. To attach the tripod mount, reverse the procedure.
C
Loosen the orientation
locking knob.
Y
P
O
Rotate the tripod mount and
align the mounting indicator
on the tripod mount with the
one on the lens.
Slide off the tripod collar
away from the rear of the
lens.
ENG-12
11. Filters
13. Extension Tubes
(Sold separately)
You can attach filters to the filter mounting thread
on the front of the lens.
• If you need a polarizing filter, use the Canon
Circular Polarizing Filter (77mm).
• To adjust the polarizing filter, first remove the
lens hood.
(Sold separately)
You can attach Extension Tube EF12 II or EF25
II for magnified shots. The shooting distance and
magnification are shown below.
Y
P
O
EF12 ll
12. Close-up Lenses
(Sold separately)
Attaching a 500D (77mm) Close-up Lens
enables close-up photography.
Magnification will be 0.14× – 0.60×.
EF25 ll
C
70mm
200mm
70mm
200mm
Camera-to-Subject
Distance (mm)
Near
Far
538
628
998
3404
400
406
862
1740
Magnification
Near
0.23×
0.28×
0.42×
0.36×
Far
0.17×
0.06×
0.38×
0.14×
Manual focusing is recommended for accurate
focusing.
• Close-up Lens 250D cannot be attached
because there is no size that fits the lens.
• Manual focusing is recommended for accurate
focusing.
ENG-13
14. Extenders
(Sold separately)
With Extender EF1.4X ll or EF2X ll attached, the lens specifications will change as follows:
Item
With EF1.4X ll Extender
With EF2X ll Extender
Focal length (mm)
98 – 280
140 – 400
Aperture
f/4 – 45
f/5.6 – 64
25°20’ – 8°50’
16°20’ – 6°10’
Diagonal
Angle of view
Vertical
13°50’ – 4°55’
Horizontal
20°50’ – 7°20’
13°40’ – 5°10’
0.30
0.44
Maximum magnification (×)
Y
P
O
9°10’ – 3°30’
• First attach the Extender to the lens, then attach the lens to the camera. Detach it from the
camera in the reverse order. If you attach the lens to the camera first, misoperation may
occur.
• Only one Extender can be attached to the lens and camera.
• If you use an Extender on the lens mounted on a EOS A2/A2E/5, set the exposure
compensation to -1/2 stop for the EF1.4X ll or -1 stop for the EF2X ll.
C
• Autofocusing is still enabled with Extender EF1.4X II/EF2X ll attached.
• When an Extender is attached, the AF speed will become slower by design to retain proper
AF control.
ENG-14
Specifications
Focal Length & Max. Aperture
70 – 200 mm, f/2.8
Lens Construction
23 elements in 19 groups
Min. Aperture
f/32
Angle of View
Diagonal: 34° – 12°
Min. Focusing Distance
1.2 m / 3.9 ft.
Max. Magnification & Field of view
0.21 × (at 200 mm), 308 × 463 – 115 × 171 mm / 12.1 × 18.2 – 4.5 × 6.7 inch (at 1.2 m)
Filter Diameter
77 mm
Max. Diameter & Length
88.8 × 199 mm / 3.5 × 7.8 inch
Weight
1490 g / 52.6 oz.
Lens Hood
ET-87
Lens Cap
E-77U/E-77 II
Case
LZ1326
C
Vertical: 19°30’ – 7°
Horizontal: 29° –10°
Y
P
O
• The lens length is measured from the mount surface to the front end of the lens. Add 21.5 mm to include the
E-77U lens cap and dust cap, and 24.2 mm for the E-77 II.
• The size and weight listed are for the lens only, except as indicated.
• Aperture settings are specified on the camera.
• All data listed is measured according to Canon standards.
• Product specifications and appearance are subject to change without notice.
ENG-15
C
CT1-8561-003
0812Ni
Y
P
O
© CANON INC. 2010
Download PDF

advertising