Product specifications | Canon 310 HS Digital Camera User Manual

Photo Printer
series
Direct Photo Guide
Table of Contents
The following ink tank is compatible with this printer.
For information on product specifications, please visit our website at
www.usa.canon.com
QT5-1042-V01
XXXXXXXX
© CANON INC. 2007
PRINTED IN XXXXXXXX
Introduction
1
How to Use the Documentation Provided
2
Printer Parts and Their Functions
3
Loading Printing Paper
8
Printing from a Memory Card
10
Printing Photographs Directly from a Compliant Device
21
Printing Photographs from a Wireless Communication Device
25
Routine Maintenance
27
Changing the Printer Settings
33
Troubleshooting
35
Appendix
47
Getting Help from Canon
Ordering Information
For additional supplies, use the following descriptions and order numbers.
Help Us Help You Better
Before you contact Canon, please record the following information.
Serial Number (located on the bottom of the product): ______________________________________________________________________________________________
Model Number (located on the top of the product): _________________________________________________________________________________________________
Setup CD-ROM number (located on the CD-ROM): ________________________________________________________________________________________________
Purchase Date: ____________________________________________________________________________________________________________________________
Customer Technical Support Sequence*
1. Internet — www.canontechsupport.com
For quick and comprehensive self-help in an intuitively guided interactive troubleshooting environment, the place to start is our helpful tech support web site. In addition,
the latest driver downloads, answers to frequently asked questions, product information, and “where to buy” instructions are found here.
2.
Email Tech Support — www.canontechsupport.com
For individual attention to a special issue, try emailing our friendly technical support representatives, specially trained to communicate quick, easy, and logical solutions
to your inquiries within 24 hours.
3.
Toll-Free Live Tech Support — (1-800-828-4040)
This option provides live telephone technical support, free of service charges, Monday-Saturday (excluding holidays), during your product’s 1 year limited warranty
period. Telephone Device for the Deaf (TDD) support is available at (1-866-251-3752).
4.
Extended Service and Support — www.canonesp.com
Canon CarePAK Extended Service Plan is a cost-attractive and easy-to-use extended service program that provides up to three full years of service and support
coverage at a very attractive price. CarePAK offers toll-free Canon technical support and includes Canon’s superb InstantExchange product replacement program. For
further information about extending your Canon service and support, call (1-800-385-2155), or visit our Web site at www.canonesp.com. CarePAK must be purchased
during your product’s warranty period.
For more information and updated program specifics, please visit our web site at www.canontechsupport.com.
*Support program specifics are subject to change without notice.
Description
Order #
Ink Tanks
CLI-36 Color
1511B002
Canon Specialty Papers
All Occasion Photo Cards (4" x 8"/ 50 sheets)
Glossy Photo Paper Credit Card Size (100 sheets)
Matte Photo Paper (4" x 6"/ 120 sheets)
Photo Paper Glossy (4" x 6"/ 50 sheets)
Photo Paper Glossy (4" x 6"/ 100 sheets)
Photo Paper Plus Double Sided (5" x 7"/ 10 sheets)
Photo Paper Plus Double Sided Album Kit (5" x 7")
Photo Paper Plus Glossy (4" x 6"/ 20 sheets)
Photo Paper Plus Glossy (4" x 6"/ 50 sheets)
Photo Paper Plus Glossy (4" x 6"/ 120 sheets)
Photo Paper Plus Glossy (5" x 7"/ 20 sheets)
Photo Paper Plus Semi-gloss (4" x 6"/ 50 sheets)
Photo Paper Pro (4" x 6"/ 20 sheets)
Photo Paper Pro (4" x 6"/ 75 sheets)
Photo Stickers (16 stickers/sheet, 5 sheets/pack)
1029A069
9157A023
7981A014
0775B021
0775B022
9981A006
0041B005
7980A007
7980A012
7980A022
7980A019
1686B014
1029A014
1029A027
0001C001
Call 1-800-OK-CANON to locate a dealer near you, or visit the Canon eStore at
www.estore.usa.canon.com.
© 2007 Canon U.S.A., Inc. Canon is a registered trademark of Canon Inc. in the United States and may be a registered trademark or trademarks in other countries. All other
product and brand names are trademarks of their respective owners. As an ENERGY STAR® partner, Canon U.S.A., Inc. has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
series
Photo Printer
Direct Photo Guide
Introduction
Exif Print
This printer supports ExifPrint.
Exif Print is a standard for enhancing the communication between digital
cameras and printers. By connecting to an Exif Print-compliant digital
camera, the camera’s image data at the time of shooting is used and
optimized, yielding extremely high quality prints.
This Direct Photo Guide uses the following symbols to indicate important
information. Always observe the instructions indicated by these symbols.
Warning
Instructions that, if ignored, could result in death or serious personal injury caused by
incorrect operation of the equipment. These must be observed for safe operation.
International ENERGY STAR® Program
As an ENERGY STAR® Partner, Canon Inc. has
determined that this product meets the ENERGY
STAR guidelines for energy efficiency.
Caution
Instructions that, if ignored, could result in personal injury or material damage caused by
incorrect operation of the equipment. These must be observed for safe operation.
Important
Instructions that must be observed for safe operation.
Power Requirements
Never use a power supply voltage other than that supplied in the country
of purchase. Using the incorrect voltage could cause a fire or electric
shock. The correct power supply voltages and frequencies are as
follows:
Depending on your application program, operations may differ. For details, refer to the
instruction manual of your application. The steps described in this manual are in Windows
Vista™ operating system Ultimate Edition (hereafter referred to as “Windows Vista”) and
Mac® OS X v.10.4.x.
AC 100-240 V, 50/60 Hz
About Consumables
Trademark Notices
z “Microsoft” is a registered trademark of Microsoft Corporation.
z “Windows” is a trademark of Microsoft Corporation, registered in the U.S. and other
countries.
z “Windows Vista” is a trademark of Microsoft Corporation.
z “Macintosh” and “Mac” are trademarks of Apple Inc., registered in the U.S. and other
countries.
z “Adobe” and “Adobe RGB (1998)” are either registered trademarks or trademarks of
Adobe Systems Incorporated in the United States and or other countries.
z “Memory Stick”, “Memory Stick PRO”, “Memory Stick Duo” and “Memory Stick PRO
Duo” are trademarks of Sony Corporation.
z “xD-Picture Card” is a trademark of Fuji Film Co. Ltd.
z “MultiMediaCard” is a trademark of the MultiMediaCard Association.
z “SD Card”, “miniSD Card”, and “microSD Card” are trademarks of SD Association.
z “IrDA Feature Trademark” is owned by the Infrared Data Association and used
under license therefrom.
z “Bluetooth” is a trademark of Bluetooth SIG, Inc.,U.S.A. and licensed to Canon Inc.
© CANON INC. 2007
All rights reserved. No part of this publication may be transmitted or copied in any form
whatsoever without the express written permission.
Consumables (ink tanks / FINE Cartridges) are available for 5 years
after production has stopped.
Safety Precautions
.
Warning
z Never attempt to plug the power cord into the power outlet or unplug the power cord
when your hands are wet.
z Never damage, modify, stretch, or excessively bend or twist the power cord. Do not
place heavy objects on the power cord.
z Never use any power supply other than the standard power supply available in the
country of purchase. Using the incorrect voltage and frequency could cause a fire or
electric shock.
z Always push the plug all the way into the power outlet.
Caution
z For safety reasons, store ink tanks out of the reach of small children.
z Do not drop or shake ink tanks as this may cause the ink to leak out and stain your
clothes and hands.
Also read the “Safety Precautions” on page 50. Observe the warnings and
cautions to avoid personal injury or damage to the printer.
Introduction
1
How to Use the Documentation
Provided
.
Printed Documentation
Setup Sheet
Be sure to read this sheet first.
This sheet explains how to setup the printer and the procedure to
install the printer driver.
Direct Photo Guide (This guide)
Read this guide when starting to use the printer.
This guide explains how to print photos while viewing them on the
LCD, and the procedure of doing the regular maintenance of the
printer.
On-screen Manuals
User’s Guide
Read this guide when starting to use the printer.
If you need further information about the printer, please refer to the
User’s Guide, which can be installed from the Setup CD-ROM. This
guide provides detailed instructions for printing from your computer.
Additional guides are also available for advanced features.
PC Printing Guide
Refer to this guide for full instructions on printer driver setting.
PC Photo Printing Guide (Windows® only)
Refer to this guide for full instructions on using the various application
software included on the Setup CD-ROM.
2
How to Use the Documentation Provided
Printer Parts and Their Functions
Main Components
„ Front View
Paper Feed Tray
Open and fold in half before printing
to support paper.
Paper Guide
Slide against the left side of the
paper stack to support paper so that
it feeds properly.
Printer Cover
Open by sliding the Lock Switch to
replace the ink tank or remove
jammed paper.
LCD Monitor
Displays menus, setting items, and
photos for printing. For information on
Screen-saver mode, see “Screensaver mode” on page 7.
Open button
Press to open the Paper Feed Tray
and Paper Output Tray.
Operation Panel
Changes the settings and operates
the printer. See “Operation Panel” on
page 5.
Paper Output Tray
The printed paper will be ejected.
Rear Tray
Load paper here.
IrDA Port
Use this port to perform wireless printing
through infrared communication. See
“Printing Photographs from a Wireless
Communication Device” on page 25.
USB Connector (for computer)
Plug in the USB cable connecting the
printer to a computer here.
Direct Print Port
Connect your PictBridge compliant
device, such as a digital camera, here to
print directly from it. See “Printing
Photographs Directly from a Compliant
Device” on page 21.
You can also connect the Bluetooth Unit
BU-20* to perform wireless printing
through Bluetooth communication. For
details, refer to the User’s Guide onscreen manual.
Card Slot
Set the memory card here. See “Using the
Memory Card” on page 10.
Access lamp
Lights or flashes to indicate the status of
the memory card. See “Inserting the
Memory Card” on page 11.
Lock Switch
Slide to the right to open the Printer
Cover.
*The Bluetooth unit is not available in some countries or regions depending on the local laws and regulations. For details, contact your local Canon Service representative.
Printer Parts and Their Functions
3
„ Interior
„ Rear View
Battery Connector Cover
Remove each cover to attach the
optional Portable Kit. To attach the
optional Portable Kit, refer to the
instruction manual provided with the
Portable Kit.
AC Adapter Connector
Connector used to connect the
supplied AC Adapter plug.
Carrying Handle
Pull out this handle to carry
the printer.
Ink lamp
Lights or flashes red to
indicate the status of the ink
tank.
See “Replacing an Ink
Tank” on page 31.
Print Head Holder
The print head is installed in
advance.
Print Head Lock Lever
Locks the Print Head.
Paper Thickness Lever
Move to the right when printing.
Important
Do not pull this lever up.
If you have accidentally pulled
them up, adjust the print head
position.
See “Aligning the Print Head” on
page 29.
Move to the left if ink smudges or
the printed surface is stained.
Return to the right after printing.
See “The Paper Thickness Lever
position is incorrect.” on page 42.
Note
For information on how to install the ink tank, refer to your setup sheet.
4
Printer Parts and Their Functions
How to Navigate Menus on the LCD
„ Operation Panel
(1)
(2)
(3)
(4)
(5)
(6) (7)
(8)
(1) ON/OFF button
Turns the printer on and off.
See “Turning On/Off the Printer” on page 6.
(2) Buttons to be used to navigate menus on the LCD
See “How to Navigate Menus on the LCD” on right column.
(3) OK button
Finalizes your selection for the menu or setting item. See “How to Navigate
Menus on the LCD” on right column.
Dismisses the error message and resumes the printer’s normal operation
after resolving a printing error or removing jammed paper.
(4) [+][-] buttons
Specifies the number of copies to print.
(5) Print button
Press to start printing according to the settings displayed on the LCD.
(6) Stop/Reset button
Cancels a print job in progress.
(7) Power lamp
Lights or flashes blue to indicate the power status.
(8) Alarm lamp
Lights or flashes orange when an error, such as paper-out or ink-out, occurs.
Note
Power lamp indicates the power status.
Off: The printer is turned off.
Lighting: The printer is ready to print, is currently printing, or is in operation.
Flashing: The printer is preparing to turn on or off.
(1) Home screen
(2) Left Function button
(3) Right Function button
(4) NAVI button
(5) HOME button
(6) Back button
(7) OK button
(8) {, }, [, and ] buttons
(9) Easy-Scroll Wheel
(1)
(2)
(4)
(3)
(5)
(6)
(7)
(8)
(9)
„ Basic Operation
This section describes the operation to navigate menus with the Easy-Scroll
Wheel, {, }, [, and ] buttons, and the OK button, taking the HOME screen
as an example.
1
2
Press the HOME button.
The HOME screen will appear.
Turn the Easy-Scroll Wheel to
select the menu, then press the OK
button.
(A)
You can turn the Easy-Scroll Wheel left
or right. You can also use the [ or
]button to select setting items.
Move the icon of the desired menu to position (A).
The selected menu screen will appear.
You can select the following menus on the HOME screen:
Select and print:
You can print the photos saved on a memory card while displaying on the LCD,
and specify the number of copies for each photo listed. See “Selecting
Photographs to Print—Select and print” on page 12.
Layout print:
You can print your favorite photo in the specified layout. See “Printing Multiple
Photos on One Sheet of Media—Layout print” on page 13.
Printer Parts and Their Functions
5
Create item:
You can create your own items such as stickers or calendars using selected
photo, or print your favorite photo with a frame. See “Using Other Useful
Printing Function” on page 16.
Special photo print:
You can print all photos saved on a memory card and print photos according to
the settings on the camera. You can also print a list of all photos and the photo
information when you shot. See “Using Other Useful Printing Function” on page
16.
Settings:
You can perform the maintenance or change the various settings of the printer.
See “When Printing Becomes Faint or Colors Are Incorrect” on page 27 or
“Changing the Printer Settings” on page 33.
Slide show:
You can display photos saved on a memory card on the LCD sequentially.
Turning On/Off the Printer
This section describes the method to turn on/off the printer.
„ Turning On the Printer
Note
If the ink tank is not installed, refer to your setup sheet to install it.
1
Plug in the AC Adapter and connect the other end to a power
outlet.
2
Press the Open button, then open the Paper Feed Tray and the
Paper Output Tray, and then fold the Paper Feed Tray in half.
„ Operation of Other Buttons
z Function buttons (2), (3)
Two Function buttons enable you to select the menu displayed at the bottom of
the LCD.
The screen that appears when you press a Function button depends on the
screen that is displayed and which Function button you press.
Left Function button (2):
When you press the left Function button on the HOME
screen, the remaining ink volume screen is displayed.
Right Function button (3): When you press the right Function button on the
HOME screen, the introductions for the selected
menu functions are displayed.
When you press them on the other than the HOME screen, the operation
procedure or the menus is displayed.
z Back button (6)
You can return the LCD to the previous screen.
z NAVI button (4)
When you do not know how to use the print function for the frequent use or how
to load paper, you can easily get the explanation from the navigation menu.
6
Printer Parts and Their Functions
Note
Pull the LCD Monitor up and adjust its angle to a position where you can see it
clearly.
3
Press the ON/OFF button to turn the printer on.
1
Turn off the printer by pressing the ON/OFF button.
Access lamp
The Power lamp flashes, then changes to steady (non-flashing).
The HOME screen appears on the LCD.
Note
If the Alarm lamp is lit orange and an error message is displayed on the LCD, see
“Error Message Is Displayed on the LCD” on page 35.
„ Turning Off the Printer
Check the following before turning off the printer.
z The Access lamp of the memory card is not flashing.
z The printer is not operating.
Important
The Access lamp flashes while the printer is reading or writing data from/to the
memory card. Removing the memory card or turning off the printer while the
Access lamp is flashing may damage the data saved on the memory card.
The Power lamp goes out and the power will be turned off.
Push down the LCD Monitor.
2
Close the Paper Feed Tray and then the Paper Output Tray.
Note
Power cord
Before unplugging the power cord, turn off the printer and ensure that the Power
lamp has gone out. You may not be able to print afterward if you unplug the power
cord when the Power lamp is lit or flashing.
„ Screen-saver mode
If you leave the printer more than about 5 minutes without using any button on
the operation panel when the printer is turned on, the LCD goes into Screensaver mode automatically.
Press the OK button to resume the LCD.
Note
When using the optional battery, the printer will be turned off automatically after
about 5 minutes from when the LCD goes into Screen-saver mode.
Printer Parts and Their Functions
7
Loading Printing Paper
3
Ensure that the Paper Thickness Lever is set to the right.
This section describes the available page size and media type, and how to load
paper.
Note
When printing, set the Paper
Thickness Lever to the right.
Set the Paper Thickness Lever
to the left only if ink smudges or
the printed surface is stained.
Return the Paper Thickness
Lever to the right after printing.
Loading paper
1
Turn on the printer.
See “Turning On the Printer” on page 6.
(1) Press the Open button, then open the Paper Feed Tray and
Paper Output Tray, and fold the Paper Feed Tray in half.
4
Load the paper.
Do not load higher than the Paper Guide’s thickness.
(1) Load the paper into the Rear Tray
with the print side facing up.
If you use Canon genuine 4" x 6" /
101.6 x 152.4 mm paper, up to 20
sheets of paper can be loaded.
(3) Slide the Paper Guide against the
left side of the paper stack.
Note
z Photo stickers
Pull up the LCD Monitor and adjust its angle in the position where you
can see it clearly.
(2) Press the ON/OFF button.
2
Flatten the four corners of the paper before loading it.
Note
If paper is curled, gently bend the corners in the opposite direction until the paper
becomes flat. See “Paper is curled.” on page 42.
Shorter margin
Important
Always load paper in portrait orientation.
8
Loading Printing Paper
(2) Align the paper stack with the
right edge of the Rear Tray.
z 4" x 6" or Card
Printing Media
z Paper Output Tray Load Limit
This section describes the available page size and media type for direct printing.
For informations of page size and media type when printing from a computer, refer
to the User’s Guide on-screen manual.
„ Compatible Media Type
We recommend that you remove the previously printed sheet from the Paper
Output Tray before continuously printing to avoid blurs and discoloration.
„ Selectable Page Size
Printer Setting for Page Size
Width x Height
Printer Setting for Media Type
Credit card
2.13 x 3.39 inches / 54.0 x 86.0 mm
Glossy Photo Paper GP-401
Glossy Photo Paper
4"x6"(101.6x152.4)
4.00 x 6.00 inches / 101.6 x 152.4 mm
Glossy Photo Paper “Everyday Use” GP-501
Glossy Photo Paper
5"x7"(127.0x177.8)
5.00 x 7.00 inches / 127.0 x 177.8 mm
Photo Paper Glossy GP-502
Glossy Photo Paper
Wide 4 x 7.1(101x180)
4.00 x 7.10 inches / 101.6 x 180.6 mm
Media Type and Model
Photo Paper Plus Semi-gloss SG-101, SG-201*1 Photo Plus Glossy
Photo Paper Plus Glossy PP-101*1
Photo Plus Glossy
Photo Paper Pro PR-101*1
Photo Paper Pro
Matte Photo Paper MP-101
Matte Photo Paper
Photo Stickers PS-101*2
—
*1 When loading a stack of paper, the printed side may become marked as it is fed
in. In this case, load paper one sheet at a time.
*2 When printing on sticker paper, select Sticker print on the Create item screen.
See “Printing Stickers with a Photo Saved on a Memory Card—Sticker print” on
page 17.
Important
z Put unused paper back into the package, and store them avoiding heat, humidity, and
direct sunlight.
z Do not touch the printed surface nor stack the printed sheets until the ink is fixed.
„ Paper Handling
Do not use the following types of paper. Using such paper will not only produce
unsatisfactory results, but can also cause the printer to jam or malfunction. Also,
do not use a cut paper or memo pad.
z Folded, curled, or wrinkled paper
z Damp paper
z Paper that is too thin (weighing less than 17 lb / 64 gsm)
z Picture postcards
z Postcards affixed with photos or stickers
z Any type of paper with holes
z Paper that is not rectangular
z Paper bound with staples or glue
z Paper with adhesives
z Paper decorated with glitter, etc.
Note
z You may not be able to purchase some Canon genuine papers depending on the
country or region of purchase.
z For information on the page sizes available for each Canon genuine paper, visit our
website.
z Paper Support Load Limit
5" x 7" / 127.0 x 177.8 mm: 10 sheets
4" x 6" / 101.6 x 152.4 mm, Wide, and Credit card: 20 sheets
Photo Stickers: 1 sheet
Loading Printing Paper
9
Printing from a Memory Card
Using the Memory Card
This section describes the memory cards compatible with this printer, and how to insert and remove them.
„ Memory Cards Supported by this Printer
The following memory cards are compatible with this printer.
Memory cards that can be directly inserted into the Card Slot:
z SD Secure Digital memory card
z SDHC memory card
z MultiMediaCard
Memory cards that can be inserted in the Card Slot using the adapter:
Important
If a memory card is inserted without an adapter, you may not be able to remove the card.
Be sure to attach it to the adapter before inserting to the Card Slot.
z Compact Flash (CF) Card
Supports Type I/II (3.3 V)
z Microdrive
z miniSD Card*1
z MEMORY STICK
z MEMORY STICK PRO
z xD-Picture Card*3
z microSD Card*2
z MEMORY STICK Duo*1
z MEMORY STICK PRO Duo*1
Important
z If you shot or saved photos on a type of memory card that is not guaranteed operation
to be used on your digital camera, the image may be unreadable on this printer.
Attempting to read such data on this printer may damage the data. For information on
memory cards that your digital camera guarantees operation, refer to the manuals
supplied with your digital camera.
z Format the memory card with a digital camera. The memory card may not be usable
with the printer if formatted on a computer.
z Do not insert more than one memory card at a time.
10
Printing from a Memory Card
z RS-MMC*1
*1 Use the special adapter provided with the card.
*2 Use “SD Card Adapter” provided with the card.
*3 Requires purchase of a separate compact flash card adapter for xD-Picture
card.
„ Printable Image Data
3
This printer supports JPEG and TIFF images created by DCF ver. 1.0/2.0
standard compliant digital cameras (Exif ver. 2.2/2.21 compliant).
Caution
z When a memory card is inserted into the Card Slot, the Access lamp is lit.
When this Access lamp is flashing, the printer is accessing to the memory
card. In this case, do not touch around the Card Slot.
z The memory card will stick out of the Card Slot, but do not force it into the slot
any further. Doing so damages the printer and the memory card.
z Make sure that the memory card is correctly oriented and labeled side is facing
up before inserting it into the Card Slot. If you force the memory card into the
Card Slot in the wrong orientation, you may damage the memory card and/or
the printer.
Important
Compatible image types are limited to JPEG and TIFF only. Other image or movie
types such as RAW images cannot be printed.
„ Inserting the Memory Card
This printer is equipped with two Card Slots to meet various types of memory
cards. Refer to the illustration on right column to find the Card Slot that
corresponds to your memory card. Check the card face and insert it gently until
it reaches the bottom and the Access lamp turns on. The card’s end protrudes
from the Card Slot even if it is correctly set.
You can also use the Card Slot as the memory card drive of the computer.
For SD Secure Digital memory card,
SDHC memory card, miniSD Card,
microSD Card, MultimediaCard,
MEMORY STICK, MEMORY STICK
PRO, MEMORY STICK Duo,
MEMORY STICK PRO Duo, and RSMMC
Note
z When Read/write mode is selected in Read/write attribute under Device
settings by using the Operation Panel on the printer, card direct printing
cannot be done. After using the Card Slot as the memory card drive of the
computer, remove the memory card, then be sure to set Read/write attribute
to Read-only mode. See “Changing the Printer Settings” on page 33.
z When you use a computer to edit or process photos saved on a memory card,
be sure to print them from the computer. If you print using the Operation Panel,
the data may not be printed correctly.
1
Lights up
Insert the memory card into the upper
slot with the labeled side facing up.
Turn on the printer.
See “Turning On the Printer” on page 6.
2
Insert only one memory card into the Card Slot.
For Compact
Flash (CF) card,
Microdrive, and
xD-Picture Card
Attach a card adapter if your memory card requires one.
Caution
When using miniSD Card, microSD
Card, xD-Picture Card, MEMORY
STICK Duo, MEMORY STICK PRO
Duo, or RS-MMC, be sure to use a
card adapter when inserting these
cards into the Card Slot.
If one of these cards is inserted
without an adapter, you may not be
able to remove the card. In this
case, see “Cannot Remove a
Memory Card” on page 46.
Insert the memory Lights up
card into the
downside slot with
the labeled side
facing up.
4
Confirm that the Access lamp has lit up.
Printing from a Memory Card
11
Printing Photographs Saved on a Memory Card
„ Removing the Memory Card
Important
If you used the Card Slot as the memory card drive of the computer, you need to
do a “safe removal” operation on your computer before physically removing the
memory card from your printer.
Right-click the removable disk icon and click Eject. If Eject is not displayed on the
screen, make sure that the Access lamp is not flashing, and then remove the
memory card.
Drag the
1
Photos saved on the memory card can be reviewed on the printer’s LCD. You can
select a photo and print a single copy of the photo, or specify the number of copies
to print.
„ Selecting Photographs to Print—Select and print
You can display the photos saved on the memory card on the LCD and print
them.
1
Prepare for printing.
(1) Turn on the printer.
See “Turning On/Off the Printer” on page 6.
icon into the Trash.
(2) Load paper.
See “Loading Printing Paper” on page 8.
Make sure that the Access lamp is lit, then remove the memory
card.
Do not remove the memory card while the Access lamp is flashing. Hold the
part of the memory card that is sticking out to remove it from the printer.
Important
The Access lamp flashes while the printer is reading or writing data from/to the
memory card. Removing the memory card or turning off the printer while the
Access lamp is flashing may damage the data saved on the memory card.
(3) Insert the memory card into the Card Slot.
See “Inserting the Memory Card” on page 11.
2
Select Select and print
OK button.
3
Confirm the page size, media type, and other settings, then select
Next, and then press the OK button.
on the Home screen, then press the
The photo selection screen is displayed.
Note
Access lamp
12
Printing from a Memory Card
z To change the settings, select the item and press the OK button.
See “Print Setting Screens” on page 15.
z may be displayed on the LCD while reading the photo.
4
Select the photo to print and specify the number of copies for each
photo.
(1) Use the Easy-Scroll Wheel or the [ or ] button to display the photo to
print.
(2) Use the [+] or [-] button to specify the
number of copies.
(3) Repeat steps (1) and (2) to specify
the number of copies for each photo.
Note
z When the page size is Credit card:
Even if both Date ON and File no. ON are set, only the shooting date will be
printed. If you want to print the file no., select Date OFF. It is not possible to
print both the shooting date and the file no.
z To cancel printing, press the Stop/Reset button.
„ Printing Multiple Photos on One Sheet of Media—Layout
print
You can print the specified photos in the specified layout (Borderless or
Bordered ×2/×4/×8/Half, borderless/Half, bordered/Half, borderless (w/lines)/
Half, bordered (w/lines)/Album ×4 (photos on right)/Album ×4 (photos on left)).
Examples:
(4) Press the OK button.
The print confirmation screen is
displayed.
.
Note
You can do…
z You can change the display for photos. See “Changing the Display—Change
display” on page 19.
z You can search for photos with the shooting date. See “Searching for Photos
with the Shooting Date—Search” on page 20.
z You can print a specified area. See “Printing a Specified Area—Trimming” on
page 19.
5
Start printing.
(1) Confirm the print settings.
Borderless
×2
1
Note
Borderless
×8
Half
bordered
Album ×4
Prepare for printing.
(1) Turn on the printer.
See “Turning On/Off the Printer” on page 6.
To change the print settings, select the
item and press the OK button. See
“Print Setting Screens” on page 15.
(2) Load paper.
See “Loading Printing Paper” on page 8.
(2) Confirm the total number of copies for
the selected photos.
(3) Press the right Function button and
confirm the selected photos and
number of copies for each photo.
Then press the OK button to return to
the print confirmation screen.
Bordered
×4
(3) Insert the memory card into the Card Slot.
See “Inserting the Memory Card” on page 11.
2
Select Layout print
button.
on the Home screen, then press the OK
(4) Press the left Function button, and change the Advanced print settings.
See “Print Setting Screens” on page 15.
(5) Press the Print button.
The specified number of copies of each photo will be printed.
Printing from a Memory Card
13
3
Use the Easy-Scroll Wheel or the [ or ] button to select the
layout, then press the OK button.
Note
z Press the Back button to cancel pasting the specified photo.
z Press the left Function button not to paste a photo in the selected frame.
z You cannot paste photos on more than one page. Start printing once you have
pasted photos on one page.
You can do...
z You can search for photos with the shooting date. See “Searching for Photos
with the Shooting Date—Search” on page 20.
z You can print a specified area. See “Printing a Specified Area—Trimming” on
page 19.
4
Confirm the page size, media type, and print quality, then select
Next, and then press the OK button.
5
Select the paste method.
7
Start printing.
(1) Confirm the print settings.
Note
z Paste automatically
Select the Search or All photos on the following Layout print screen, and
proceed to Step 7.
All the photos are pasted automatically in the selected layout.
z Paste one by one
Specify to paste photos one by one on the specified layout. Proceed to
Step 6.
6
(2) Use [+] [-] buttons to change the
number of copies.
(3) Press the left Function button, and
change the Advanced print settings.
See “Print Setting Screens” on page
15.
Paste photos one by one.
(1) Use the Easy-Scroll Wheel or the [
or ] button to display the photo you
want to paste and press the OK
button.
The photo is pasted on the layout.
(2) Repeat (1) for each photo you want to print.
(3) Confirm the layout and then press the OK button.
The print confirmation screen is displayed.
14
To change the print settings, select the
item and press the OK button. See
“Print Setting Screens” on page 15.
Printing from a Memory Card
(4) Press the Print button.
The specified number of copies will be printed.
Note
z Even if both Date ON and File no. ON are set, only the shooting date will be
printed. If you want to print the file no., select Date OFF. It is not possible to
print both the shooting date and the file no.
z To cancel printing, press the Stop/Reset button.
Print Setting Screens
Note
This section describes about the print setting screen and the print confirmation
screen displayed during the operation to print photos on a memory card.
Note
z For the print setting screen, select Next to proceed to the next step.
z For the print confirmation screen, press the Print button to start printing.
z The print settings are retained even if the printer is turned off.
„ Advanced Print Settings Screen
When printing directly from a PictBridge compliant device, see “Setting Items” on page 24.
When printing from a wireless communication, see “Setting Items” on page 25.
Print Setting Screen
Print Confirmation Screen
(1)
(2)
(3)
(4)
When you press the left Function button in the print settings confirmation
screen, the Auto image fix screen is displayed.
(1)
(2)
(3)
(4)
(1) Page size
Select the page size of the loaded paper.
(2) Media type
Select the media type of the loaded paper.
When Auto image fix ON is selected, the scene or person’s face of a shot
photo is recognized and the most suitable correction for each photo is made
automatically. It makes a darkened face by backlight brighter to print. It also
analyzes a scene such as scenery, night scene, person, etc. and corrects each
scene with the most suitable color, brightness, or contrasts automatically to
print.
(3) Print quality
Adjust the print quality.
(4) Borderless print
Select bordered or borderless print.
„ Print Settings
1
Note
z Photos in a memory card are printed in Auto image fix as default. In Auto image
fix, you can specify only Date or File no. on the next page.
z If you do not satisfy the print result in Auto image fix, you can select Manual
correction. If you select Manual correction, you can specify each advanced
setting item.
When the print setting screen or the print confirmation screen is
displayed, select the setting item, then press the OK button.
The setting screen for the selected item will be displayed.
2
Select the page size and the media type, then press the OK button.
Printing from a Memory Card
15
z Date
Activate/deactivate to print the shooting date on a photo.
z File no.
Activate/deactivate to print the file no. on a photo.
Using Other Useful Printing Function
You can enjoy various printouts of photos in the memory card.
1
Note
(1) Turn on the printer.
See “Turning On/Off the Printer” on page 6.
Under conditions listed below, even if both Date ON and File no. ON are set, only
the shooting date will be printed. If you want to print the file no., select Date OFF.
z Layout print or Calendar print is selected.
z Credit card is selected in Page size.
z Red eye correc.
Corrects red eyes in portraits caused by flash photography.
z Vivid photo
Makes green and blue more lively.
z Photo opt. pro
Automatically optimizes brightness and tone of a photo.
z Noise reduction
Reduces the noise on blue areas like the sky as well as on black areas.
z Face brightener
Brightens a darkened face on the photo taken against the light.
z Image optimizer
Corrects and smooths the jagged contours for printing.
z Brightness
Adjust brightness.
z Contrast
Adjust contrast.
z Color hue
Adjust color hue.
For example, you can increase red or yellow to adjust the skin tone.
z Effects
Applies special effects to the photo, such as printing in sepia tones or with a
sketch illustration like effect.
16
Printing from a Memory Card
Prepare for printing.
(2) Load paper.
See “Loading Printing Paper” on page 8.
(3) Insert the memory card into the Card Slot.
See “Inserting the Memory Card” on page 11.
2
Select Create item
or Special photo print
screen, then press the OK button.
on the Home
Printing menus on the Create item screen:
z Calendar print:
z Sticker print:
See “Creating a Calendar—Calendar print” on page 17.
See “Printing Stickers with a Photo Saved on a Memory
Card—Sticker print” on page 17.
See “Printing Photographs with a Frame—Framed photo
print” on page 17.
z Framed photo
print:
Printing menus on the Special photo print screen:
See “Printing ID Photo—ID photo size print” on page 17.
z ID photo size
print:
z Print all photos: See “Printing all Photographs—Print all photos” on page
18.
z Photo index print: See “Printing a Photo Index—Photo index print” on page
z Captured info
print:
z DPOF print:
18.
See “Print Photograph Information—Captured info print”
on page 18.
See “Printing Photographs from Your Camera—DPOF
print” on page 18.
Note
Depending on your selected printing menu, you can do…
z You can change the advanced print setting. See “Advanced Print Settings
Screen” on page 15.
z You can change the display for photos. See “Changing the Display—Change
display” on page 19.
z You can search for photos with the shooting date. See “Searching for Photos
with the Shooting Date—Search” on page 20.
z You can print a specified area. See “Printing a Specified Area—Trimming” on
page 19.
„ Creating a Calendar—Calendar print
Note
You can create your own original calendar with your favorite photo printed on it.
1
Select Calendar print on the
Create item screen.
2
Select the format, the photo to
print, the background color,
etc., then press the Print
button.
z Load a single sheet at a time.
z To print without a frame, press the left Function button in the frame selection
screen.
z If the photo is upside-down, you can use the { or } button to rotate the frame
180 degrees.
z If you want to rotate a photo 90 degrees to match a frame, rotate the trimming
area. See “Printing a Specified Area—Trimming” on page 19.
z When printing stickers, be sure to load the media so that it faces in the correct
direction. See “Loading Printing Paper” on page 8.
„ Printing Photographs with a Frame—Framed photo print
You can print your favorite photo with a frame.
Important
Always load paper in portrait orientation.
Note
z Select the landscape format for a landscape-oriented photo or the portrait
format for a portrait-oriented photo.
If the photo is upside-down, you can use the { or } button to rotate the photo
180 degrees.
z To change the start of the week on the printed calendar, press the left Function
button on the screen where Advanced is displayed.
z Even if both Date ON and File no. ON are set, only the shooting date will be
printed. If you want to print the file no., select Date OFF. It is not possible to print
both the shooting date and the file no.
„ Printing Stickers with a Photo Saved on a Memory Card—
Sticker print
You can print your favorite photo with a frame on the Canon genuine Photo
Stickers.
1
Select Sticker print on the
Create item screen.
2
Select Stickers x16 layout,
the photo to print, the frame,
and the number of copies,
then press the Print button.
1
2
Select Framed photo print on the Create item screen.
Select the frame and the photo to print, then press the Print button.
Note
z If the photo is upside-down, you can use the { or } button to rotate the frame
180 degrees.
z If you want to rotate a photo 90 degrees to match a frame, rotate the trimming
area. See “Printing a Specified Area—Trimming” on page 19.
„ Printing ID Photo—ID photo size print
You can print ID size photos.
1
2
Select ID photo size print on the Special photo print screen.
Select the photo size and the photo to print, then press the Print
button.
Caution
Print the photo on the larger-sized paper than your selected photo size.
Note
Choose the area to print by using the following buttons.
z {, }, [, and ] buttons: Position the printing area.
z Easy-Scroll Wheel: Sets the printing area.
Turn the Easy-Scroll Wheel clockwise to enlarge the size of the printing area or
counterclockwise to reduce it.
z Right Function button: Rotate the printing area.
To switch the printing area between portrait and landscape orientations, press
this button.
z OK button: Finalizes your selection of printing area.
Printing from a Memory Card
17
„ Printing all Photographs—Print all photos
You can print all photos saved on the memory card.
1
2
Select Print all photo on the Special photo print screen.
Specify the print range, then press the Print button.
„ Printing a Photo Index—Photo index print
You can print a list of all photos saved on the memory card.
1
2
Select Photo index print on the Special photo print screen.
Specify the print range, then press the Print button.
Note
When using index printing, the number of images printed on a single sheet of
paper depends on the page size, as follows:
– 5"×7" / 127.0×177.8 mm: 35 photos
– 4"×6" / 101.6×152.4 mm: 24 photos
– Credit card: 6 photos
– Wide / 101 x 180 mm: 28 photos
„ Print Photograph Information—Captured info print
You can print the Photograph information (Exif information) when you shot on
the white space of photo.
1
2
Select Captured info print on the Special photo print screen.
Select the photo to print, then press the Print button.
„ Printing Photographs from Your Camera—DPOF print
If DPOF (Digital Print Order Format) settings are made on the camera, photos
are printed automatically according to those settings.
1
2
18
Select DPOF print on the Special photo print screen.
Select Yes, then press the Print button.
Printing from a Memory Card
Note
z The printer supports the following DPOF functions:
Version:
Based on ver. 1.00
Supported image types:
CIFF, Exif (JPEG/TIFF), and JFIF
Print Style Standard Print:
Prints photos that were specified as “Standard Print” with DPOF
Print Style Index Print:
Prints an index of photos that were specified as “Index Print” with DPOF using
the printer's index printing layout
Print Photo Select:
Prints only photos specified with DPOF (cannot be specified from the Operation
Panel)
Number of copies:
Prints the number of copies specified with DPOF (cannot be specified from the
Operation Panel)
z Prints are automatically enlarged or reduced to match the page size. Edges of
the photo may be clipped off depending on the page size.
z The shot date order setting by which photos are sorted follows that of DPOF.
z DPOF is a standard format to record the specified information regarding
images, such as which image or number of copies to print.
Using Useful Display Function
„ Printing a Specified Area—Trimming
You can edit images displayed on the LCD by cropping them.
There are other useful functions to print the photo from memory card.
z “Changing the Display—Change display” below
z “Display photos sequentially—Slide show” below
z “Printing a Specified Area—Trimming” on right column
z “Searching for Photos with the Shooting Date—Search” on page 20
„ Changing the Display—Change display
When you press the left Function button when Change display is displayed on
the screen, you can change the way photos are displayed.
Normal screen display: Shows one photo.
Thumbnail display:
Shows nine photos at a time. Select the photo using
the Easy-Scroll Wheel or the {, }, [, or ] button,
then press the [+] [-] buttons to specify the number
of copies.
Full-screen display:
Shows one photo at full-screen.
Enlarged display:
Shows enlarged photo twice as much as the
original. Move the area to show using the {, }, [,
or ] button. Press the OK button to return to the
previous display mode.
Slide show:
Shows next photos automatically. To stop the slide
show, press the Stop/Reset button.
Note
Crop images after specifying the page size, media type, and bordered or
borderless printing in the print setting screen. If you change the paper settings
after cropping, the cropped area may be adjusted to match the paper, or be
disabled completely.
1
2
(2) Select Trimming, then press the OK
button.
The cropping edit screen is
displayed.
3
on the HOME screen, then press the OK
Press the Stop/Reset button to stop the slide show.
Note
You can do…
You can specify the image quality of the slide show. See “Slide show setting” on
page 34.
Choose the area to print.
z {, }, [, and ]buttons: Position the cropping frame.
z Easy-Scroll Wheel: Sets the cropping frame size.
Turn the Easy-Scroll Wheel clockwise to enlarge the size of the cropping
frame or counterclockwise to reduce it.
z Right Function button: Rotates the cropping frame.
To switch the cropping frame between portrait and landscape orientations,
press this button.
You can display photos saved on the memory card on the LCD sequentially.
Select Slide show
button.
Display the cropping edit screen.
(1) Press the right Function button when
Edit is displayed on the screen.
„ Display photos sequentially—Slide show
1
Select the photo to crop.
4
Press the OK button to finalize your selection of cropping area.
The area to be cropped is specified, and the original photo is displayed.
Note
z The cropped image cannot be newly saved on the memory card.
z The cropping area is displayed only for photos which have been cropped.
z To change the cropped area once it has been set, press the right Function
button again when Edit is displayed on the screen, select Trimming, then
press the OK button.
z To cancel cropping after cropping has been set, press the right Function button
again when Edit is displayed on the screen, select Cancel trimming, then
press the OK button. Select Displayed images only or All images, then press
the OK button.
Printing from a Memory Card
19
„ Searching for Photos with the Shooting Date—Search
3
Specify the date range.
z If you selected One date only
You can choose to display and print only photos shot on the specified date or
within the specified range of dates.
(1) Specify the date to search for.
Note
If the number of copies to print is already specified for some photos before
searching with the shooting date, or if some photos are already pasted on a
layout, those photos will still be selected for printing even if they were not shot on
the specified date or within the specified date range.
1
Display the search method screen.
z If you selected Select date range
z Setting in Edit
(1) Specify the start date to search, then
press the OK button.
(1) Press the right Function button when Edit is displayed on the screen.
(2) Select Search, then press the OK button.
The Search screen is displayed.
z Setting in Search in the Specify print range screen (Layout print, Photo
index print, and Print all photos)
(1) Select Search, then press the OK button.
The Search screen is displayed.
2
Set the search method.
(1) Select the search method.
To specify only one date for search, select One day only.
To specify the range for search, select Select date range.
(2) Press the OK button.
The date input screen is displayed.
Note
It may take a while for the date input screen to be displayed depending on the
number of photos saved on the memory card.
20
Printing from a Memory Card
(2) Specify the end date to search.
4
Press the OK button to start searching.
The printer starts searching and the photos within the specified date range
are displayed.
Note
z The date that you specified is displayed according to the settings of Date
display in Other settings. See “Date display” on page 34.
z To cancel the selected date range, press the right Function button when Edit is
displayed on the screen, select Cancel selected date, then press the OK
button.
Printing Photographs Directly from a
Compliant Device
You can connect a PictBridge compliant device such as a digital camera,
camcorder, or mobile phone using a USB cable recommended by the device’s
manufacturer, and print recorded images directly without using a computer.
„ Connectable Devices
PictBridge is an industry standard enabling a range of digital photo solutions,
including the direct printing of photos from a digital still camera, camcorder or
mobile phone* without the need to use a computer. A device can be connected
to this printer for direct printing regardless of the manufacturer or the model as
long as it complies with the PictBridge standard.
* PictBridge compliant digital still cameras, digital camcorders, and cameraequipped mobile phones are hereafter collectively referred to as “PictBridge
compliant device”.
A device with this mark is PictBridge compliant.
„ Printable Image Data Format
This printer prints images taken with a DCF (Design rule for Camera File
system) ver. 1.0/2.0-compatible digital camera (Exif ver. 2.2/2.21 compliant), as
well as PNG files.
1
Prepare for printing
(1) Turn on the printer.
See “Turning On/Off the Printer” on page 6.
(2) Load paper.
See “Loading Printing Paper” on page 8.
2
Connect the PictBridge compliant device to the printer.
Note
Depending on the model or brand of your device, you may have to select a print
mode compliant with PictBridge before connecting the device. You may also
have to turn on the device or select Play mode manually after connecting the
device to the printer.
Perform necessary operations on the PictBridge compliant device before
connecting it to this printer according to instructions given in the device’s
instruction manual.
(1) Make sure that the PictBridge compliant device is turned off.
(2) Connect the PictBridge compliant device to the printer using a USB cable
recommended by the manufacturer of the device.
The device turns on automatically.
If your device does not turn on automatically, turn it on manually.
Printing Photographs Directly from a Compliant Device
To connect a PictBridge compliant device to this printer, use a USB cable
recommended by the device’s manufacturer.
Caution
Do not connect any equipment other than PictBridge compliant devices or the optional
Bluetooth unit BU-20 to the Direct Print Port of the printer. If you do so, electric shock,
fire, or damage to the printer could result.
Important
z Set up the printer according to your setup sheet before you start printing.
z Never disconnect the USB cable during printing unless when explicitly allowed to by
the PictBridge compliant device. When disconnecting the USB cable between the
PictBridge compliant device and printer, follow the instructions given in the device’s
instruction manual.
(3) Set up the PictBridge compliant device for direct printing.
will appear on the LCD of the device when the printer is correctly
connected.
Note
When printing photos with the PictBridge compliant device connected to the printer, we
recommend the use of the AC adapter supplied with the device. If you are using the
device battery, be sure to charge it fully.
Printing Photographs Directly from a Compliant Device
21
3
Specify the print settings such as paper type and layout.
See “About PictBridge Print Settings” below.
You can make settings using the menu on the LCD of your PictBridge
compliant device. Select the size and type of paper that you loaded in the
printer.
If your PictBridge compliant device does not have setting menu, change the
setting from the printer. For details, see “Settings on the Printer” on page 23.
4
z Paper type
Paper type setting
Loadable paper*2
Photo
Photo Paper Plus Glossy
Glossy Photo Paper
Glossy Photo Paper “Everyday Use”
Start printing from your PictBridge compliant device.
Photo Paper Glossy
Photo Paper Plus Semi-gloss
About PictBridge Print Settings
„ Settings on a PictBridge Compliant Device
This section describes the print settings on a PictBridge compliant device.
When operating the device, be sure to follow the instructions given in the
instruction manual of your PictBridge compliant device.
Note
z In the following description, names of setting items are given according to those
used in Canon-brand PictBridge compliant devices. Setting item names may be
different depending on the brand or model of your device.
z Some setting items explained below may not be available on some devices. In this
case, the settings made on the printer are applied. Also, when some items are set
to Default on a PictBridge compliant device, the printer settings for these items
are applied. For details, see “Settings on the Printer” on page 23.
z Paper Size and Paper Type Settings
The following sizes and types of printing paper can be used when printing from
a PictBridge compliant device.
z Paper size
4" x 6" / 101.6 x 152.4 mm, 5" x 7" / 127.0 x 177.8 mm*1, Credit card, Wide*1
Photo Stickers*3
Fast Photo
Photo Paper Pro
The available page sizes vary depending on the media type. For details, visit
our website.
*1 Can be selected only on certain Canon-brand PictBridge compliant
devices.
*2 You may not be able to purchase some Canon genuine papers
depending on the country or region of purchase.
*3 Exclusively used to print photo stickers. When printing on sticker paper,
see “Layout Setting” below.
z Layout Setting
Various layout options are available.
z Bordered/Borderless: You can select whether or not to print an image with a
border.
z When printing onto Photo Stickers (PS-101) (16-up), use the following
settings.
(1) Select 10x15cm/4"x6" for the Paper size, and Photo for the Paper
type.
(2) Select N-up for the Layout, then select 16.
Even though some PictBridge compliant devices display the Layout
option; 2-up, 4-up, 9-up, and 16-up, always select 16-up. If there are no
options on the PictBridge compliant device that correspond to 16-up,
printing on Photo Stickers (PS-101) is not possible.
z Shooting Info (Exif Data): You can print shooting info (Exif Data) in the margin
of selected individual images.
22
Printing Photographs Directly from a Compliant Device
z Date/File No. Print Setting
You can specify whether the date and/or file number will be printed.
Note
z If the images already have dates superimposed when shot, set this PictBridge
setting item to Off. If you select Date, File No., or Both, the date and/or file
number will be printed over the date printed by the device’s function.
z Depending on the paper size and layout, the date will only be printed even
when Both is selected.
„ Settings on the Printer
This section describes how to change the print settings on the printer.
Set the print settings to Default on the PictBridge compliant device when you
want to print according to the settings on the printer.
z Displaying the PictBridge Settings Screen and Specifying
the Settings:
1
z Image Optimize Setting
You can select the optimization method to obtain high print quality. When you
select Default, the most suitable correction for each photo is made using the
Auto image fix function of the printer. See “Setting on the Printer” on right
column.
When you select On, photos are optimized for printing using the Photo opt. pro
function.
If you are using a Canon-brand PictBridge compliant device, the following
additional options may be available, depending on the model.
z VIVID makes green and blue more lively.
z NR (Noise Reduction) reduces the noise on blue areas like the sky as well as
on black areas.
z Face brightens a darkened face on the photo taken against the light.
z Red-Eye corrects red eyes in portraits caused by flash photography.
z Trimming Setting
You can select an area to print.
Turn on the printer.
See “Turning On the Printer” on page 6.
2
Display the PictBridge settings screen.
(1) Select Settings
on the HOME screen, then press the OK button.
(2) Select Device settings, then press the OK button.
(3) Select PictBridge settings, then press the OK button.
3
Confirm and change the settings.
(1) Select the item to set, then press the OK button.
(2) Select the item, then press the OK button.
(3) Confirm the print settings, select Next, then press the OK button.
(4) Select Auto image fix ON or Manual correction, then press the OK
button.
When Auto image fix ON is selected, the scene or person’s face of a
shot photo is recognized and the most suitable correction for each photo
is made automatically. It makes a darkened face by backlight brighter to
print. It also analyzes a scene such as scenery, night scene, person, etc.
and corrects each scene with the most suitable color, brightness, or
contrasts automatically to print.
When Manual correction is selected, you can make each effect setting
described in “Setting Items” on page 24. Repeat steps (1) and (2) and
then specify each item. After finishing all settings you need, select OK
and then press the OK button. You can print from the PictBridge
compliant device with specified settings.
Printing Photographs Directly from a Compliant Device
23
z Setting Items
(1)
(5)
(2)
(6)
(3)
(4)
(7)
(8)
(9)
(10)
(13)
(14)
(11)
(12)
Setting Item
Description
Corresponding
Setting of
PictBridge
Compliant Devices*
(1)
Page size
Select the page size, when
printing directly from a
PictBridge compliant device.
Paper size
(2)
Media type
Select the media type, when
printing directly from a
PictBridge compliant device.
Paper type
–
(3)
Print quality
Select the print quality, when
printing directly from a
PictBridge compliant device.
(4)
Borderless print
Select bordered or borderless Layout
print.
24
Printing Photographs Directly from a Compliant Device
Setting Item
Description
Corresponding
Setting of
PictBridge
Compliant Devices*
(5)
Photo opt. pro
Automatically optimizes
brightness and tone of a
photo.
Image optimize
(6)
Vivid photo
Makes green and blue more
lively.
(7)
Face brightener
Brightens a darkened face on
the photo taken against the
light.
(8)
Noise reduction
Reduces the noise on blue
areas like the sky as well as
on black areas.
(9)
Image optimizer
Corrects and smooths the
jagged contours for printing.
(10) Red eye correc.
Corrects red eyes in portraits
caused by flash photography.
(11) Brightness
Adjust brightness.
(12) Contrast
Adjust contrast.
(13) Color hue
Adjust color hue. For
example, you can increase
red or yellow to adjust the skin
tone.
(14) Effects
Applies special effects to the
photo, such as printing in
sepia tones or with a sketch
illustration like effect.
* Set the items in this column to Default on the PictBridge compliant device when
you want to make settings on the printer.
Printing Photographs from a Wireless
Communication Device
If you have a mobile phone or a PDA with an infrared port for wireless data
transmission, you can print photos through wireless connection with the printer. If
the optional Bluetooth unit BU-20 is connected to the printer, you can also print
photos through Bluetooth communication.
Important
To perform printing correctly from a mobile phone or PDA through Infrared
communication, the following conditions should be satisfied.
– Compatible devices: A mobile phone or PDA with an IrDA port that supports image
data transmission through Infrared communication.
– Printable data: Images shot with a camera of the mobile phone or PDA.
When printing photos through Infrared Communication:
z See “Setting the Page Size, Media Type, and Layout When Printing from a
Mobile Phone or a PDA” below.
z See “Printing via Infrared Communication” on page 26.
When printing photos through Bluetooth Communication:
Refer to the User’s Guide on-screen manual.
(3) Select Wireless print settings, then press the OK button.
The Wireless print settings screen is displayed.
3
Confirm or change the settings.
(1) Select the item to set, then press the OK button.
(2) Change the setting, then press the OK button.
(3) After finishing all settings you need, select OK and then press the OK
button.
The photo in the mobile phone or PDA can be printed according to the
following settings.
„ Setting Items
(1)
(2)
(3)
(4)
Setting the Page Size, Media Type, and Layout
When Printing from a Mobile Phone or a PDA
(1) Select the page size for printing photos saved on a mobile phone or PDA.
When printing from a mobile phone or PDA through Infrared communication or
Bluetooth communication, you can select the page size, media type, layout and
borderless printing on the Wireless print settings screen.
The default is borderless printing on 4" x 6" Photo Paper Plus Glossy.
(3) Select Image optimizer ON to correct and smooth out the jagged
contours when printing.
Turn on the printer.
See “Turning On/Off the Printer” on page 6.
2
(4) Select the layout of the photos as below.
Sticker print:
Stickers x 16
Printing on paper other than sticker:
Bordered x 1, x 2, x 4, x 8
Borderless x 1, x 2, x 4, x 8
„ Displaying the Wireless Print Settings Screen and
Specifying the Settings
1
(2) Select the media type for printing photos saved on a mobile phone or
PDA.
Display the Wireless print settings screen.
(1) Select Settings
on the HOME screen, then press the OK button.
(2) Select Device settings, then press the OK button.
Printing Photographs from a Wireless Communication Device
25
Printing via Infrared Communication
You can print photos stored in your mobile phone or PDA via infrared
communication.
When printing through infrared communication, also refer to the instruction manual
of your mobile phone or PDA.
1
Prepare for printing.
(1) Turn on the printer.
See “Turning On/Off the Printer” on page 6.
(2) Load paper.
See “Loading Printing Paper” on page 8.
2
Set the print setting and layout.
See “Setting the Page Size, Media Type, and Layout When Printing from a
Mobile Phone or a PDA” on page 25.
3
Start Infrared Communication.
(1) Place the mobile phone or PDA so that its infrared port (A) comes face to
face to that of the printer (B) at a distance of less than approximately 8
inches / 20 cm (C).
(2) Select the photo to print and send the data to the printer using the
infrared communication function of the mobile phone or PDA.
Printing will start after receiving all data.
Note
z Do not place any obstacle between the infrared ports of the printer and mobile
phone or PDA it will block data transmission.
z During printing, be careful not to interrupt infrared communication with the
printer. If it is interrupted, send the data from the mobile phone or PDA again.
z Depending on your device, the print quality may be degraded due to the
restriction on the infrared transfer capacity.
z We recommend printing on sticker or credit card-sized paper when the print
quality on other types of paper is not fine.
About transmittable data
z Due to security settings on the mobile phone or PDA, downloaded content or
photos downloaded from an URL attached to an E-mail cannot be printed.
z Video files cannot be printed.
z Depending on the size of a photo, it may take a while for this printer to start to
print after starting the infrared communication.
z Depending on your device, data saved on a memory card may not be printed.
z Printed quality and orientation (portrait or landscape) are determined
automatically according to the shot photo size.
z Depending on the photo size shot on the mobile phone, the edges of the image
may be cut off when performing borderless printing; the margin size may
change when printing with borders.
z If the photo file is over 1.8 MB in size, it may not be possible to send the file.
Note
z The effective angle of the IrDA Port of the printer is about 10 degrees from the
central axis (D) in both vertical and horizontal directions.
z The effective range of communication with the printer depends on the mobile
phone or PDA you are using. For details, refer the manual of your mobile phone
or PDA.
(B) IrDA Port of the printer
(D)
(A) Infrared Port
(C)
26
Printing Photographs from a Wireless Communication Device
Routine Maintenance
Note
When Printing Becomes Faint or Colors Are
Incorrect
When printing becomes faint or colors are incorrect, the ink may have run out, or
the Print Head Nozzles are probably clogged. Follow the procedures below to clean
the nozzles.
Step 1
“Printing the Nozzle Check Pattern” on right column
After Print Head
Cleaning,
print the nozzle
check pattern.
Before performing maintenance
z Open the Printer Cover and make sure that the ink lamp is lit red.
– If the ink lamp is flashing slowly, the ink tank is running low. If the printing is blurred,
replace the ink tank. See “Replacing an Ink Tank” on page 30.
If the printing is not blurred, you can continue printing for a while, but the printer may
not be able to print properly along the way. We recommend you to have a
replacement ink tank available.
– If the ink lamp is flashing fast, the ink tank is empty. Replace the ink tank.
See “Replacing an Ink Tank” on page 30.
– If the ink lamp is not lit, the tank is not set properly. Press the
mark on the ink
tank until the tank clicks into place.
z If the print result is not your expected one, for instance, the printed photo is rough,
performing the Print Head Alignment may resolve the problem.
See “Aligning the Print Head” on page 29.
„ Printing the Nozzle Check Pattern
Print the nozzle check pattern to determine whether the ink ejects properly from
the Print Head Nozzles.
1
If the pattern is printed
normally, select All A.
Prepare for printing.
(1) Turn on the printer.
See “Turning On/Off the Printer” on page 6.
(2) Load one sheet of Canon genuine 4" x 6" / 101.6 x 152.4 mm paper or
Canon genuine 5" x 7" / 127.0 x 177.8 mm paper in the Rear Tray. See
“Loading Printing Paper” on page 8.
If the print quality is poor, perform Print Head Cleaning.
(3) Make sure that the Paper Thickness Lever is set to the right.
Step 2
“Print Head Cleaning” on page 28
2
Print the Nozzle Check Pattern.
(1) Select Settings
on the Home screen, then press the OK button.
If the problem remains after performing Print Head Cleaning twice.
Step 3
“Print Head Deep Cleaning” on page 29
If Print Head Deep Cleaning does not resolve the problem, the Print Head may be
damaged. Contact your Canon Service representative.
Routine Maintenance
27
(2) Select Maintenance, then press the OK button.
(3)
Select Nozzle check pattern, then
press the OK button.
The confirmation screen of Nozzle
check pattern is displayed.
„ Print Head Cleaning
Clean the Print Head if white streaks appear in the printed nozzle check pattern.
Cleaning unclogs the nozzles and restores the print head condition. Note that
cleaning the Print Head causes used ink to be absorbed in the ink absorber.
Cleaning the Print Head consumes ink, so perform Print Head Cleaning only
when necessary.
1
Prepare for printing.
Turn on the printer.
See “Turning On/Off the Printer” on page 6.
(4) Select Yes, then press the OK button.
The nozzle check pattern is printed and the confirmation screen of
patterns is displayed.
3
2
Start Print Head Cleaning.
(1) Select Settings
on the Home screen, then press the OK button.
(2) Select Maintenance, then press the OK button.
Examining the nozzle check pattern.
z When all print check patterns are
successfully printed:
Select All A, then press the OK button.
(3)
Select Cleaning, then press the OK
button.
(4)
Select Yes, then press the OK
button.
Print Head Cleaning starts.
Important
When no white stripes appear
z When there is more than one white stripe on the print check patterns:
Select Also B, then press the OK button
When white stripes appear
The confirmation screen of Cleaning is displayed.
Select Yes to start the cleaning.
See “Print Head Cleaning” on right column.
Do not perform any other operations
until the Print Head Cleaning finishes.
This takes about 1 minute.
3
Print the nozzle check pattern to verify that the Print Head Nozzles
are clean.
When Print Head Cleaning finishes, the confirmation message is displayed.
Select Yes to print the Nozzle Check Pattern, and verify the Print Head
Nozzles.
See “Printing the Nozzle Check Pattern” on page 27.
Note
If the problem remains after performing Print Head Cleaning twice, try Print Head
Deep Cleaning.
28
Routine Maintenance
„ Print Head Deep Cleaning
„ Aligning the Print Head
If print quality does not improve by standard Print Head Cleaning, try Print Head
Deep Cleaning, which is a more powerful process. Note that cleaning the Print
Head causes used ink to be absorbed in the ink absorber. Print Head Deep
Cleaning consumes more ink than standard Print Head Cleaning, so perform
this procedure only when necessary.
1
If print quality is poor, adjust the Print Head position. It may solve the problem.
1
(1) Turn on the printer.
See “Turning On/Off the Printer” on page 6.
Prepare for printing.
(2) Load one sheet of the supplied 5" x 7" / 127.0 x 177.8 mm paper or
same-sized Canon genuine paper in the Rear Tray.
Turn on the printer.
See “Turning On/Off the Printer” on page 6.
2
Important
Start Print Head Deep Cleaning.
(1) Select Settings
Be sure to use the following paper.
Photo Paper Plus Glossy (PP-101) 5" x 7" / 127.0 x 177.8 mm
on the Home screen, then press the OK button.
(2) Select Maintenance, then press the OK button.
(3) Select Deep cleaning, then press
the OK button.
(4) Select Yes, then press the OK
button.
Print Head Deep Cleaning starts.
Prepare for printing.
(3) Make sure that the Paper Thickness Lever is set to the right.
2
Adjust the print head position.
(1) Select Settings
Note
Important
If you select Head alignment print,
the printer exits the process after
printing the current adjustment
values.
Do not perform any other operations until the Print Head Deep Cleaning finishes.
This takes about 90 seconds.
3
Print the nozzle check pattern to verify that the Print Head Nozzles
are clean.
When Print Head Deep Cleaning finishes, the confirmation message is
displayed. Select Yes to print the Nozzle Check Pattern, and verify the Print
Head Nozzles.
See “Printing the Nozzle Check Pattern” on page 27.
Note
If the print head nozzles are still not clean, turn off the printer and perform another
Print Head Deep Cleaning after 24 hours.
If this does not resolve the problem, the Print Head may be damaged. Contact
your Canon service representative.
on the Home screen, then press the OK button.
(2) Select Maintenance, then press the OK button.
(3) Select Auto head align, then press
the OK button.
(4) Select Yes, then press the OK button.
The pattern is printed and the Print Head is aligned automatically. This
takes about 3 minutes.
Note
z The print head alignment pattern is printed in black and blue.
z If adjustment was not done successfully, the “Auto head align has failed. Press
the OK button and repeat operation. <See manual>.” error message is
displayed on the LCD. For details, see “Error Message Is Displayed on the
LCD” on page 35.
Routine Maintenance
29
Replacing an Ink Tank
Ink is low. You can continue printing for a while, but we
recommend you to have a new ink tank available.
This section explains the way to confirm the ink status and the procedure to replace
an ink tank.
When ink runs out or other errors occur, an error message is displayed on the LCD
to inform you of the error. See “Error Message Is Displayed on the LCD” on page 35
and confirm how to handle it.
Ink may have run out. See “The following ink may have run
out. Replacing the ink tank is recommended. U041” on
page 35 and take the appropriate action.
Note
The ink status information is also displayed in the screen that appears during
printing.
Note
z For information on the compatible ink tank, refer to the back cover of this manual.
z If printing becomes faint or white streaks appear despite sufficient ink levels, see
“When Printing Becomes Faint or Colors Are Incorrect” on page 27.
An error message may appear on the LCD during printing.
Ink has run out. See “The following ink
has run out. Replace the ink tank. U170”
on page 36 and take the appropriate
action.
„ Getting the Ink Status Information
You can confirm the status of the ink tank in the following ways:
z “With the LCD of this Printer” below.
z “With the Ink Lamp” on right column.
When printing from your computer, error messages appear on your computer
screen as well.
z With the LCD of this Printer
You can confirm the status of the ink tank in the remaining ink volume screen on
the LCD.
1
Make sure that the printer is turned on, then press the HOME
button.
The HOME screen is displayed.
2
z With the Ink Lamp
You can confirm the status of the ink tank by the ink lamp. Open the Printer
Cover of the printer to confirm how the ink lamp lights or flashes.
z Ink lamp is on
The ink tank is correctly set and there is enough ink remaining to print.
z Ink lamp is flashing
Flashing slowly (at around 3-second intervals)
Press the left Function button.
The screen as shown below will be displayed.
Confirm whether any symbols are
displayed here.
......Repeats
Ink is low. You can continue printing for a while, but we recommend you to
have a new ink tank available.
Flashing quickly (at around 1-second intervals)
......Repeats
The ink tank is empty. Replace it with a new one.
z Ink lamp is off
The tank is not set properly. Press the
mark on the ink tank until the
tank clicks into place.
If the lamp is still off after reinserting the ink tank, there has been an error
and the printer cannot print.
30
Routine Maintenance
„ Replacing an Ink Tank
Important
Important
Handling Ink
z To maintain optimal printing quality, we recommend the use of specified Canon
genuine ink tank.
Refilling ink is not recommended.
z Once you remove an ink tank, replace it immediately. Do not leave the printer
with an ink tank removed.
z Replace an empty tank with a new one. Inserting a partially used ink tank may
cause the nozzles to clog. Furthermore, with such a tank, the printer will not be
able to inform you when to replace the tank properly.
z Once an ink tank has been installed, do not remove it from the printer and
leave it out in the open.
This will cause the ink tank to dry out, and the printer may not operate properly
when it is reinstalled. To maintain optimal printing quality, use an ink tank within
six months of first use.
z Color ink is consumed in Print Head Cleaning and Print Head Deep Cleaning,
which may be necessary to maintain the printer's performance. When an ink
tank is out of ink, replace it immediately with a new one.
1
2
If the Printer Cover is left open
for more than 10 minutes, the
Print Head Holder moves to the
right. Close and reopen the
Printer Cover to return the
holder to the center.
3
Remove the empty ink tank.
Make sure that the printer is turned on.
Open the Printer Cover.
(1) Slide the Lock Switch
toward the right to
open the Printer
Cover.
The Print Head
Holder moves to the
center.
(1) Push the tab.
(2) Remove the ink tank.
Important
z Handle ink tank carefully to avoid staining clothing or the surrounding area.
z Discard empty ink tank according to the local laws and regulations
regarding disposal of consumables.
Routine Maintenance
31
4
Prepare a replacement ink tank.
Important
(1) Unpack a new ink tank and remove
the orange protective cap.
Discard the cap once it is removed.
(B)
If the front (innermost) part of the ink tank (A) is sticking up, push down on
the Canon logo on the ink tank as illustrated below. Do not remove the ink
tank forcibly.
(A)
Important
z Do not touch the electrical contacts (A)
on the ink tank. Doing so can cause the
printer to malfunction or become
unable to print.
z Do not re-attach the protective cap
once you have removed it. Discard it
according to the local laws and
regulations regarding disposal of
consumables.
z Do not touch the open ink ports (B)
once the protective cap is removed, as
this may prevent the ink from being
ejected properly.
(A)
5
6
Close the Printer Cover.
(1)
(2) Close the Printer Cover firmly
until it clicks into place.
Insert the ink tank.
(1) Insert the new ink tank slightly
on the ink
slanted to meet the
on the printer.
tank to
(1)
(2)
(2) Push down on the
mark on
the ink tank until it clicks into
place.
Ensure that the ink lamp is lit
red.
(2)
32
(1) Lift the Printer Cover and pull the
Lock Bar close.
Routine Maintenance
Note
When you start printing after replacing the ink tank, Print Head Cleaning is performed
automatically. Do not perform any other operations until Print Head Cleaning finishes.
Changing the Printer Settings
This section describes the procedure to change the settings in the Device settings
screen, taking the steps to specify Date display as an example.
1
4
Change the settings.
(1) Select the setting item, then press the OK button.
Make sure that the printer is turned on, then press the HOME
button.
The HOME screen is displayed.
2
Display the Device settings screen.
(1) Select Settings
3
on the Home screen, then press the OK button.
(2) Select Device settings, then press the OK button.
The Device settings screen is displayed.
Print settings
Select the menu.
„ Ink drying wait time
(1) Select the setting item, then press the OK button.
The setting screen for the selected item is displayed.
Use this setting only if the print surface becomes smudged.
Important
Be sure to set this back to Standard after printing since it takes longer than usual
for one printing.
Wireless print settings
For details, see “Setting the Page Size, Media Type, and Layout When Printing
from a Mobile Phone or a PDA” on page 25.
(2) Select the menu, then press the OK button.
Bluetooth settings
For details, refer to the User’s Guide on-screen manual.
PictBridge settings
For details, see “Settings on the Printer” on page 23.
Changing the Printer Settings
33
Other settings
Language selection
„ Date display
Changes the language for LCD messages and menus.
Changes the display format of shooting dates when printed.
Note
z When Date ON is selected on the advanced print settings screen, the shooting
date is printed in the date display format you selected. For print setting, see
“Advanced Print Settings Screen” on page 15.
z The shooting date format is as specified in the DPOF setting from DPOF
printing.
„ Read/write attribute
Selects whether to allow data to be written onto memory cards from a computer.
Important
z Remove the memory card before changing this setting. For details, refer to the
User’s Guide on-screen manual.
z When you write the data on the memory card, connect the printer with the AC
adapter. The printer cannot be set to the Read/write mode with using the
optional battery. The printer can be set to the Read/write mode when using
both the AC adapter and optional battery, but do not remove the AC adapter
when you write the data on the memory card.
z If you set this setting to Read/write mode, card direct printing cannot be done.
After you finish operation of the memory card dedicated drive, be sure to set it
back to Read-only mode. And also, when you turn off the printer, the Read/
write mode will be canceled and the setting is returned to the Read-only
mode when you turn on the printer next time.
„ Slide show setting
Selects Image quality: Standard or Image quality: High for the image display
quality of the slide show.
Note
When Image quality: High is selected, it may take time until images are
displayed.
34
Changing the Printer Settings
Reset setting
You can change the settings back to the default, except for the LCD language and
the position of the Print Head.
Troubleshooting
This section describes troubleshooting tips for problems you may encounter when
using the printer.
Note
Cause
The print head lock lever
is not properly applied.
Open the cover and press
the lock buttons on both
ends of the lever.
Action
z The lock lever of the Print Head is not set properly
(there are two tabs of the lock lever). Push both tabs
(left and right) until each clicks into place.
This section mainly describes the methods of printer operation for troubleshooting. To
handle problems using your computer, refer to “Troubleshooting” in the User’s Guide onscreen manual. For details on how to view the on-screen manuals, “Reading the Onscreen Manuals” on page 47.
z
z
z
z
z
z
z
z
z
z
z
z
z
“Error Message Is Displayed on the LCD” on page 35
“LCD Cannot Be Seen At All” on page 38
“An Unintended Language Is Displayed on the LCD” on page 38
“Cannot Install the Printer Driver” on page 39
“Cannot Connect to Computer Properly” on page 40
“Print Results Not Satisfactory” on page 40
“Printer Does Not Start” on page 43
“Paper Does Not Feed Properly” on page 43
“Paper Jam” on page 43
“The Power Lamp (blue) and Alarm Lamp (orange) Flash Alternately” on page 44
“Error Message Appears on a PictBridge Compliant Device” on page 44
“Cannot Remove a Memory Card” on page 46
“Cannot Print Properly through Wireless Communication” on page 46
Error Message Is Displayed on the LCD
Cause
The following ink may
have run out.
Replacing the ink tank is
recommended.
U041
Action
If the lamp on the ink tank is flashing, ink may have
run out.
Replacing the ink tank is recommended.
If printing is in progress and you want to continue
printing, press the OK button with the ink tank
installed. Then printing can continue. Replacing the
ink tank is recommended after the printing. The
printer may be damaged if printing is continued under
the ink out condition.
See “Replacing an Ink Tank” on page 30.
The following ink tank
cannot be recognized.
U043
Print head is not installed.
Install the print head.
U051
The type of print head is
incorrect.
Install the correct print
head.
U052
The following ink tank
cannot be recognized.
U140
U150
z The ink tank is not set properly. Push the ink tank until
it clicks into place.
The ink tank is not set properly. Push the ink tank
until it clicks into place and ensure that the ink lamp is
lit red.
Remove the Print Head and then reinstall it. If the
error is not resolved, the Print Head may be
damaged. Contact your Canon Service
representative.
z The ink tank is not compatible with this printer. (The
lamp on the ink tank is off.)
Install an appropriate ink tank.
See “Replacing an Ink Tank” on page 30.
z An Ink tank error has occurred. (The lamp on the ink
tank is off.) Replace the ink tank.
See “Replacing an Ink Tank” on page 30.
Troubleshooting
35
Cause
The following ink has run
out.
Replace the ink tank.
U170
Action
Ink has run out. (The lamp on the ink tank flashes.)
Replace the ink tank and close the Printer Cover.
Printing under the current condition may damage the
printer.
If you want to continue printing in this condition, you
need to release the function for detecting the
remaining ink level. Press and hold the Stop/Reset
button for at least 5 seconds, and then release it.
* With this operation, releasing the function for
detecting the remaining ink level is memorized.
Please be advised that Canon shall not be liable for
any malfunction or trouble which may be caused by
continuation of printing under the ink out condition.
See “Replacing an Ink Tank” on page 30.
Cause
There are no photos in
memory card.
The ink absorber is
almost full. Press [OK] to
continue printing. Contact
the service center.
Note
If the function for detecting the remaining ink level is
disabled, the ink tank in gray is displayed in the remaining
ink volume screen on the LCD. See “Getting the Ink
Status Information” on page 30.
Printer detected ink out
condition of the following
ink.
Replace the ink tank.
U180
Printer detected ink out condition. (The lamp on the
ink tank flashes.)
Replace the ink tank and close the Printer Cover.
Printing with an ink tank that was once empty may
damage the printer.
If you want to continue printing in this condition, you
need to release the function for detecting the
remaining ink level. Press and hold the Stop/Reset
button for at least 5 seconds, and then release it.
* With this operation, releasing the function for
detecting the remaining ink level is memorized.
Please be advised that Canon shall not be liable for
any malfunction or trouble caused by continuation of
printing under the ink out condition or refilled ink tank.
See “Replacing an Ink Tank” on page 30.
Note
If the function for detecting the remaining ink level is
disabled, the ink tank in gray is displayed in the remaining
ink volume screen on the LCD. See “Getting the Ink
Status Information” on page 30.
36
Troubleshooting
The device may be
incompatible.
Remove the device and
check the manual
supplied with the
connected device.
Action
z There are no image data saved on the memory card
that can be read by this printer.
z The printer may not recognize the file if the file name
or the folder path contains certain characters. Use only
alphanumeric characters.
z Photo data edited or processed on a computer must
be printed from the computer.
The printer has a built-in ink absorber to hold the ink
used during Print Head Cleaning, for example.
This error message indicates that the ink absorber is
nearly full.
Press the OK button to cancel the error so you can
continue printing.
However, because printing is disabled once the ink
absorber becomes completely full and until the ink
absorber is replaced, you are recommended to
contact your Canon service representative as early
as possible (You will need to replace a particular part
of the printer).
z A communication time out occurs if an operation takes
too long or if it takes too much time to send data. This
may cancel printing. In such cases, disconnect and
reconnect the USB cable.
When printing from a PictBridge compliant device,
depending on the model or brand of your device, you
may have to select a PictBridge compliant print mode
on the device before connecting it to the printer.
You may also have to turn on your device or select
Play mode manually after connecting the device to the
printer. Perform necessary operations before
connecting your device referring to its instruction
manual.
If the error is still not resolved, check if you can print
another photograph.
z Check your device connected to the printer. Only
PictBridge compliant devices or the optional Bluetooth
Unit BU-20 can be connected to the printer for direct
printing.
Cause
Printer error has
occurred.
Turn off power then back
on again. If problem
persists, see the manual.
Action
Follow the procedure below to resolve the problem.
(1) Turn off the printer, and unplug the power cord of
the printer from the power supply.
If you are attaching the optional battery, remove it
once.
(2) After a while, plug the power cord of the printer
back in, and then turn on the printer.
If the same error occurs, make sure that the ink tank
is set properly.
Caution
If you cannot confirm that the ink tank is set
properly since the Print Head Holder moves to the
right, contact your Canon service representative.
No battery.
Turn printer off and use
the AC adapter or install a
charged battery.
The card is currently
write-enabled.
Set to read-only mode
before performing
operation.
An unsupported USB hub
is connected.
Remove the hub.
If the ink tank is not set properly, do not remove it
forcibly. See Step 5 of “Replacing an Ink Tank” on
page 30 and set the ink tank properly. After that,
perform the steps (1) and (2) above once again.
The optional battery is running low.
(1) Turn off the printer.
(2) Connect the supplied AC adapter or attach the
charged battery, then turn on the printer.
For details on how to charge the battery, refer to the
manual supplied with the battery.
The Card Slot is set to Read/write mode.
You cannot print in this mode. After writing on the
memory card, set to Read-only mode again.
If a PictBridge compliant device is connected via a
USB hub, remove the hub and connect it directly to
the printer.
Cause
Auto head align has
failed.
Press [OK] and repeat
operation. <See manual>
Action
Possible causes are as follows:
z Paper of size other than 5" x 7" / 127.0 x 177.8 mm is
loaded in the Rear Tray.
Press the OK button on the printer to dismiss the
error message, then load one sheet of the supplied 5"
x 7" / 127.0 x 177.8 mm paper or same-sized Canon
genuine paper* in the Rear Tray.
z Paper is not loaded in the Rear Tray.
Press the OK button on the printer to dismiss the
error message, and then load paper in the Rear Tray.
z Paper is loaded with the wrong side facing upwards.
Press the OK button on the printer to dismiss the
error message, then load one sheet of the supplied 5"
x 7" / 127.0 x 177.8 mm paper or same-sized Canon
genuine paper* with printing side up in the Rear Tray.
z The Paper Guide is not touching the edge of paper.
If the Paper Guide is not touching the edge of paper,
the paper at a slant passes through inside the printer
and the Auto Head Alignment may be failed.
Press the OK button on the printer to dismiss the
error message, then load one sheet of the supplied 5"
x 7" / 127.0 x 177.8 mm paper or same-sized Canon
genuine paper* in the Rear Tray.
* Use the following paper.
Photo Paper Plus Glossy PP-101
z Print Head nozzles are clogged.
Press the OK button on the printer to dismiss the
error message, and print the nozzle check pattern to
check the status of the Print Head. To print the nozzle
check pattern, see “Printing the Nozzle Check
Pattern” on page 27.
z The Paper Output Slot is exposed to strong light.
Press the OK button on the printer to dismiss the
error message, and then adjust your operating
environment and/or the position of the printer so that
the Paper Output Slot is not exposed directly to
strong light.
After carrying out the above measures, if the problem
continues after aligning the Print Head again, press
the OK button to dismiss the error message, and
then perform Manual Print Head Alignment.
Troubleshooting
37
Note
Adjusting the Print Head Manually
If the Automatic Print Head Alignment does not work or if you wish to adjust the print head
manually, follow the procedure below.
1. Turn on the printer, and then load three sheets of Canon genuine 4" x 6" /
101.6 x 152.4 mm paper in the Rear Tray.
You can also load Canon genuine 5" x 7" / 127.0 x 177.8 mm paper to perform
Manual Print Head Alignment.
* Slide the Paper Guide against the left side of the paper stack.
* Use the Canon genuine 4" x 6" / 101.6 x 152.4 mm paper or Canon genuine 5" x 7"
/ 127.0 x 177.8 mm paper.
2.
3.
4.
5.
Select Settings
on the Home screen, then press the OK button.
Select Maintenance, then press the OK button.
Select Manual head align, then press the OK button.
Select Yes, then press the OK button.
The Print Head Alignment pattern is printed.
The pattern is printed in black and blue only.
6. When “Did the patterns print correctly?” is displayed, confirm that the
pattern is printed correctly, then select Yes, and then press the OK button.
7. Check the printed patterns and use the [ or ] to input the number of the
pattern in columns A to E that has the least noticeable streaks, then press the
OK button.
8. Make sure that the paper is loaded, then press the OK button.
The second Print Head alignment pattern is printed.
9. In the same way, select the best patterns for columns F to H, then press the
OK button.
10.In the same way, print the third sheet and select the best patterns for columns
I to N, then press the OK button.
38
Troubleshooting
LCD Cannot Be Seen At All
Cause
Action
z If the Power lamp is off
The Printer is not
The printer is not powered on. Connect the power cord
powered on or the LCD is
and press the ON/OFF button. The printer will power
in the screen-saver mode.
on and the LCD will display a message.
z If the Power lamp is lit
On the Operation Panel, press a button the other than
the ON/OFF button.
An Unintended Language Is Displayed on the
LCD
Cause
Action
The language you want to
be displayed is not
selected
Select the language you want to be displayed
following the procedure below.
(1) Press the HOME button. Wait for about 5
seconds, then select
, and then press the OK
button.
(2) Press the ] button to select
, then press
the OK button.
(3) Press the } button four times, then press the OK
button.
If the Bluetooth unit is connected to the printer,
press the } button five times, then press the OK
button.
(4) Press the { or } button to select the language
for the LCD, then press the OK button.
Cannot Install the Printer Driver
Cause
Unable to proceed
beyond the Printer
Connection screen.
Action
If you were unable to proceed beyond the Printer
Connection screen, follow the procedure below to
reinstall the printer driver.
Cause
Installation does not start
automatically when the
Setup CD-ROM is
inserted into your
computer’s disc drive.
Action
(1) Click Start then Computer.
In Windows XP, Click Start then My Computer.
In Windows 2000, double-click the My Computer
icon on the desktop.
(2) Double-click the CD-ROM icon
displayed window.
on the
Note
To use the Run command to start the setup program,
specify your disc drive and then the name of the setup
program, MSETUP4.EXE. The drive letter of the disc
drive depends on your computer.
Double-click the CD-ROM icon on your desktop to start
installation.
(1) Click Cancel on the Printer Connection screen.
(2) Click Start Over on the Installation Failure
screen.
(3) Click Back on the screen that appears next.
(4) Click Exit on the PIXMA XXX screen (where
“XXX” is your printer’s name), then remove the
CD-ROM.
(5) Turn the printer off.
(6) Restart your computer.
(7) Make sure you have no application software
running, including anti-virus software.
(8) Follow the procedure described in your setup
sheet to reinstall the printer driver.
If the CD-ROM icon is not displayed, restart your
computer. If the icon is still not displayed, try different
disks and see if they are displayed. If other disks are
displayed, there is a problem with the Setup CD-ROM.
Contact your Canon service representative.
Installation procedure not
followed correctly.
Follow the procedure described in your setup sheet for
proper installation.
If the printer driver was not installed correctly, uninstall
the printer driver, restart your computer, and then reinstall
the printer driver. Refer to the PC Printing Guide onscreen manual.
Note
If the installer was forced to be terminated due to a
Windows error, the system may be in an unstable
condition and you may not be able to install the printer
driver. Restart your computer before reinstalling.
Troubleshooting
39
Cannot Connect to Computer Properly
„ Printing Speed Is Slow/USB2.0 Hi-Speed Connection
Does Not Work
Cause
Action
Your system environment
is not fully compatible with
USB 2.0 Hi-Speed.
If your system environment is not fully compatible
with USB 2.0 Hi-Speed, the printer will operate at a
lower speed provided under USB 1.1. In this case,
the printer operates properly but printing speed may
slow down due to communication speed.
Check the following to ensure that your system
environment supports USB 2.0 Hi-Speed connection.
z The USB port on your computer supports USB 2.0 HiSpeed connection.
z The USB cable, and the USB hub if you are using
one, support USB 2.0 Hi-Speed connection.
Be sure to use a certified USB 2.0 Hi-Speed cable.
We recommend the cable to be no longer than
around 10 feet/3 meters.
z The operating system of your computer supports
USB 2.0 Hi-Speed connection.
Obtain and install the latest update for your computer.
z The USB 2.0 Hi-Speed driver operates properly.
Obtain the latest version of the USB 2.0 Hi-Speed
driver compatible with your hardware and install it on
your computer.
Important
For details on USB 2.0 Hi-Speed of your system
environment, contact the manufacturer of your computer,
USB cable, or USB hub.
Print Results Not Satisfactory
If the print result is not satisfactory such as white streaks, misaligned lines, and
uneven colors, confirm the paper and print quality settings first.
z Check 1: Do the page size and media type settings match
the size and type of the loaded paper?
When these settings are incorrect, you cannot obtain a proper print result. If you
are printing a photograph or an illustration, incorrect paper type setting may
reduce the quality of printout color.
Also, if you print with an incorrect paper type setting, the printed surface may be
scratched. In borderless printing, uneven coloring may occur depending on the
combination of the paper type setting and the loaded paper.
z Check 2: Did you set the print quality setting appropriately?
Select a print quality option suitable to the paper and image for printing. If you
notice blurs or uneven colors, increase the print quality setting and try printing
again.
* When printing from a PictBridge compliant device, set the print quality setting
by using the Operation Panel on the printer. You cannot make this setting from
a PictBridge compliant device.
* You cannot change the print quality setting when printing from a wireless
communication device.
The method to confirm the paper and print quality settings differs depending on
what you do with your printer.
To print from your memory
card by operating the printer
To print from a PictBridge
compliant device
To print from a wireless
communication device
„ “This device can perform faster” Message Is Displayed
Cause
Action
Your system environment
is not fully compatible with
USB 2.0 Hi-Speed.
Your system environment is not compatible with USB
2.0.
See “Printing Speed Is Slow/USB2.0 Hi-Speed
Connection Does Not Work” above.
40
Troubleshooting
To print from a computer
Confirm by using the Operation Panel on the printer. See
“Print Setting Screens” on page 15.
Confirm by using your PictBridge compliant device or the
Operation Panel on the printer. See “Printing Photographs
Directly from a Compliant Device” on page 21.
Confirm by using the Operation Panel on the printer.
When printing data through Infrared communication, see
“Printing Photographs from a Wireless Communication
Device” on page 25.
When printing data through Bluetooth communication,
refer to the User’s Guide on-screen manual.
Confirm by using the printer driver. Refer to the PC
Printing Guide on-screen manual.
z Check 3: If the problem is not resolved, there may be other
causes.
See also the sections below.
„ Printing Does Not Start/Printing Is Blurred/Colors Are
Wrong/Straight Lines Are Misaligned
Cause
Ink tank is empty.
Action
See “Error Message Is Displayed on the LCD” on
page 35 to identify the ink error, and then take the
appropriate action depending on the error condition.
Print Head nozzles are
clogged.
See “When Printing Becomes Faint or Colors Are
Incorrect” on page 27 and perform any necessary
maintenance operation.
The media is loaded with
the wrong side facing
upwards.
Many types of paper are made to be printed on only
a particular side of the paper.
Printing on the wrong side may cause unclear prints
or incorrect color.
For detailed information on the printable side, refer to
the instruction manuals supplied with the paper.
The Paper Thickness
Lever position is
incorrect.
Normally set the Paper Thickness Lever to the right.
Depending on the printing content, the printed
surface may become scratched. In this case, set the
Paper Thickness Lever to the left.
* Return the Paper Thickness Lever to the right after
printing. If you do not return the lever, the distance
between the Print Head and printing paper stays
broadened and the inside of the printer will easily get
dirty. The image quality also may be decreased.
Note
If the corners or edges of the printed paper are smudged,
try to print with the Paper Thickness Lever set to the left.
Print Head is misaligned.
If you did not align the Print Head, straight lines may
be printed misaligned. If you unlocked the Print Head
Lock Lever accidentally, make sure to align the Print
Head after relocking the lock lever.
See “Aligning the Print Head” on page 29 and
perform Automatic Print Head Alignment. If this does
not solve the problem, see “Adjusting the Print Head
Manually” on page 38 and perform Manual Print
Head Alignment.
„ White Streaks
Cause
Print Head nozzles are
clogged.
Action
See “When Printing Becomes Faint or Colors Are
Incorrect” on page 27 and perform any necessary
maintenance operation.
„ Printed Paper Curls or Has Ink Blots
Cause
Action
Paper is too thin.
When printing data with high color saturation such as
photographs or images in deep color, we recommend
using Photo Paper Pro or other Canon genuine
paper.
Printed paper takes long
to dry.
In the Operation Panel, specify a longer Ink drying
wait time in Settings > Device settings > Print
settings. This makes dry faster, which helps prevent
curls and ink blots.
„ Printed Surface Is Scratched/Paper Is Smudged
Cause
Action
Paper Feed Roller is dirty. Clean the Paper Feed Roller. Cleaning the Paper
Feed Roller will wear the roller, so perform this
procedure only when necessary.
For details on cleaning, refer to “Cleaning the Paper
Feed Roller (Roller Cleaning)” of the User’s Guide
on-screen manual.
Inside of the printer is
dirty.
Performing many printings may leave some ink inside
the printer, causing printouts to be smudged. In this
case, perform Bottom Plate Cleaning to clean the
inside of the printer.
For details on cleaning, refer to “Cleaning the Inside
of the Printer (Bottom Plate Cleaning)” of the User’s
Guide on-screen manual.
Printing on inappropriate
type of paper.
z Check to see if the paper you are printing on is not too
thick or curled. See “Printing Media” on page 9.
z When performing Borderless Printing, print quality may
be reduced at the top and bottom edges of the paper.
Troubleshooting
41
Cause
Paper is curled.
Action
Cause
If you are using paper with either any of the corners
or the whole printing surface curled, the paper may
become dirty, not feed properly, or both. Use such
paper after correcting paper curl as follows.
(1) With the printing side (A) facing up, cover the
paper with a fresh sheet of plain paper to avoid
staining or scratching the surface.
(2) Roll up the paper in a direction opposite to paper
curl as seen below.
(1)
(2)
Action
The Paper Thickness
Normally set the Paper Thickness Lever to the right.
Lever position is incorrect. Depending on the printing content, the printed
surface may become scratched. In this case, set the
Paper Thickness Lever to the left.
* Return the Paper Thickness Lever to the right after
printing. If you do not return the lever, the distance
between the Print Head and printing paper stays
broadened and the inside of the printer will easily get
dirty. The image quality also may be decreased.
Note
If the corners or edges of the printed paper are smudged,
try to print with the Paper Thickness Lever set to the left.
Sheets of paper are
scratched
(A)
(3) Check to see that the paper curl is within
approximately 0.08 to 0.2 inches / 2 to 5 mm (B)
in height.
(A)
„ Colors Are Uneven or Streaked
Cause
(B)
We recommend printing curl-corrected paper one
sheet at a time.
Note
Depending on the media type, the paper may be
smudged or may not be fed properly even if it is not
curled.
In such case, follow the procedure described above
to curl the paper before printing.
This may improve the print result.
42
Troubleshooting
Depending on the media type, printed surface may
be scratched as it is fed into the Rear Tray, and
printing result is not satisfactory. In this case, load
one sheet at a time.
Action
Print Head nozzles are
clogged.
See “When Printing Becomes Faint or Colors Are
Incorrect” on page 27 and perform any necessary
maintenance operation.
Print Head is misaligned.
See “Aligning the Print Head” on page 29 to perform
Automatic Print Head Alignment. If this does not
solve the problem, see “Adjusting the Print Head
Manually” on page 38 to perform Manual Print Head
Alignment.
Printer Does Not Start
Paper Jam
„ Printing Does Not Start
Cause
Cause
Action
Ink tank is empty.
Confirm the error message displayed on the LCD
and take the appropriate action to resolve the error.
Ink tank is not installed
securely.
If the ink lamp is not lit, press the
mark on the ink
tank until it clicks into place. The ink lamp lights up
red when the ink tank is fully inserted.
Paper jammed in the
Paper Output Slot or the
Rear Tray.
Action
Remove the paper following the procedure below.
(1) Slowly pull the paper out, either from the Rear
Tray or from the paper output slot, whichever is
easier.
Paper Does Not Feed Properly
Cause
Printing on inappropriate
type of paper.
Action
Check to see if the paper you are printing on is not
too thick or curled. See “Printing Media” on page 9.
Paper Feed Roller is dirty. Clean the Paper Feed Roller. Cleaning the Paper
Feed Roller will wear the roller, so perform this
procedure only when necessary.
For details on cleaning, refer to “Cleaning the Paper
Feed Roller (Roller Cleaning)” of the User’s Guide
on-screen manual.
Paper not loaded
properly.
Foreign object in the Rear
Tray.
Make sure of the following when you load paper in
the printer.
z When loading two or more sheets of paper, align the
edges of the sheets before loading.
z Always load the paper in portrait orientation in the
Rear Tray, regardless of the printing orientation.
z Load the paper with the print side facing UP. Align the
paper stack against the right side of the Rear Tray
and slide the Paper Guide so that it just touches the
left edge of the stack.
Make sure that there are no foreign objects in the
Rear Tray.
z If the paper tears and a piece remains inside the
printer, open the Printer Cover and remove it.
Be careful not to touch the components inside the
printer.
After removing all paper, close the Printer Cover, turn
the printer off, and turn it back on.
z If you cannot pull the paper out, turn the printer off
and turn it back on. The paper will be ejected
automatically.
(2) Reload the paper in the printer, and press the OK
button on the printer.
If you turned off the printer in step (1), all print
jobs in queue are canceled. Reprint if necessary.
Note
z For details on how to load paper, see “Loading
Printing Paper” on page 8.
z When reloading the paper in the printer, see “Paper
Does Not Feed Properly” on left column to confirm
that you are using the correct paper and are loading it
into the printer correctly.
If you cannot remove the paper or the paper tears
inside the printer, or if the paper jam error continues
after removing the paper, contact your Canon Service
representative.
Troubleshooting
43
Cause
Landscape credit cardsized paper jammed
inside the printer.
Action
Do not load credit card-sized paper in the landscape
orientation.
Remove the paper following the procedure below.
(1) Load a single sheet of the paper in the Rear Tray
in portrait orientation.
Do not load it in the landscape orientation.
(2) Start printing.
The paper is fed and then pushes out the jammed
paper as it ejects.
If you cannot remove the jammed paper, contact your
Canon Service representative.
The Power Lamp (blue) and Alarm Lamp (orange)
Flash Alternately
Disconnect the USB cable from the printer, turn the printer off, and then unplug the
printer from the power supply. Plug the printer back in and turn the printer back on
after leaving it for a while.
If the problem is not resolved, contact your Canon Service representative.
44
Troubleshooting
Error Message Appears on a PictBridge
Compliant Device
The following are the possible errors that may occur when printing directly from a
PictBridge compatible device and the countermeasures to clear them.
Note
z This section describes errors that are indicated on Canon-brand PictBridge compliant
devices. The error messages and operations may vary depending on the device you
are using.
For errors on non-Canon PictBridge compliant devices, check the error message on
the LCD and take the appropriate action to clear the error. For details, see “Error
Message Is Displayed on the LCD” on page 35.
z For the errors indicated on the PictBridge compliant device and their solution, also
refer to the instruction manual of the device. For other troubles on the device, contact
the manufacturer.
Error Message on
PictBridge-Compliant
Device
Action
“Printer in use”
Images are being printed from the computer.
Wait until printing ends.
If the printer is warming up, wait until warm-up ends.
When it is ready, the printer starts printing
automatically.
“No paper”
Load the paper in the Rear Tray, and select
Continue* in the display on your PictBridge
compliant device.
* To resume printing, you can also press the OK
button on the printer instead of selecting Continue.
“Paper jam”
Select Stop in the display on your camera to stop
printing.
Remove the jammed paper, load new paper, and
press the OK button on the printer and try printing
again.
Error Message on
PictBridge-Compliant
Device
“Paper lever error”
Action
Normally set the Paper Thickness Lever to the right.
Depending on the printing content, the printed
surface may become scratched. In this case, set the
Paper Thickness Lever to the left.
* Return the Paper Thickness Lever to the right after
printing. If you do not return the lever, the distance
between the Print Head and printing paper stays
broadened and the inside of the printer will easily get
dirty. The image quality also may be decreased.
“Printer cover open”
Close the Printer Cover on the printer.
“No print head”
The Print Head is not installed or defective.
For details on how to resolve the error, see “Install the
print head. U051 The type of print head is incorrect.
Install the correct print head. U052” on page 35.
“Waste tank full”/
“Ink absorber full”
The ink absorber is nearly full. For details on how to
resolve the error, see “The ink absorber is almost full.
Press [OK] to continue printing. Contact the service
center.” on page 36.
“No ink”/“Ink cassette
error”
An ink tank is not installed properly, or is out of ink.
See the error message on the LCD and take the
appropriate action to resolve the error. See “Error
Message Is Displayed on the LCD” on page 35.
“Ink error”
An ink tank that was once empty is installed.
For details on how to resolve the error, see “Printer
detected ink out condition of the following ink.
Replace the ink tank. U180” on page 36.
“Hardware Error”
The optional battery has running short. Follow the
procedure below.
(1) Turn the Printer off.
(2) Connect the supplied AC adapter or attach the
charged battery.
(3) Turn the Printer on.
Error Message on
PictBridge-Compliant
Device
“Printer error”
Action
An error requiring servicing might have occurred
(Power lamp and Alarm lamp flash alternately).
Disconnect the USB cable between the printer and
the PictBridge compliant device, turn off the printer,
and unplug the power cord of the printer from the
power supply. After a while, plug the power cord of
the printer back in, turn on the printer, and then
reconnect the camera to the printer.
If the same error occurs, contact your Canon service
representative.
The ink tank error has occurred.
Replace the ink tank. See “Replacing an Ink Tank” on
page 30.
Troubleshooting
45
Cannot Remove a Memory Card
Cause
miniSD Card, microSD
Card, xD-Picture Card,
MEMORY STICK Duo,
MEMORYSTICK PRO
Duo, or RS-MMC is
attempted to insert into
the printer without
attaching to the special
adapter.
Action
Remove the memory card with printer tilted slightly
downward. Tilt the printer on the wide table securely
placed, otherwise, the printer may drop and cause an
accident. If you cannot remove the memory card,
contact your Canon service representative.
Important
Never attempt to remove a memory card using a thin
stick or tweezers. Doing so may damage the printer.
46
Troubleshooting
Cannot Print Properly through Wireless
Communication
This section describes how to solve the problems occurred during printing data
through Infrared communication. As for the problems occurred during printing data
through Bluetooth communication, refer to the User’s Guide on-screen manual.
Cause
Action
Printer placement is
inadequate.
When printing through infrared communication,
confirm that the IrDA ports on the printer and the
mobile phone are placed face to face with each other
at a proper angle and distance, and that there is
nothing blocking them. Then, retry printing.
Operational distance and angle vary depending on
the specifications of your mobile phone and your
operating environment, but generally place the
printer within around 8 inches / 20 cm from the
mobile phone in a position that enables proper
communication.
During infrared
communication, infrared
rays were blocked.
During sending, be careful not to interrupt infrared
communication with the printer. If it is interrupted,
send the data from the mobile phone or the PDA
again.
The conditions to print
properly through the
infrared communication
are not met.
The infrared communication function of the printer is
only compatible with mobile phones with IrDA
compliant infrared communication ports. Printing
through infrared communication cannot be
performed by any other types of mobile phones.
See “Printing Photographs from a Wireless
Communication Device” on page 25.
Appendix
Reading the On-screen Manuals
For detailed instructions on installing the on-screen manuals, refer to your setup
sheet.
You can view the on-screen manuals in the following way:
To view the on-screen manual, double-click the XXX On-screen Manual shortcut
icon on the desktop, or click Start > All Programs (or Programs) > Canon XXX
Manual > XXX On-screen Manual (where “XXX” is your printer’s name).
System Requirements
Browser: Windows HTML Help Viewer
Note
z Microsoft® Internet Explorer 5.0 or later must be installed.
z The on-screen manual may not be displayed properly depending on your
operating system or Internet Explorer version. We recommend that you keep
your system up to date with Windows Update.
About Option
z Portable Kit LK-60 series
The Portable Kit LK-60 series is the kit to operate the printer with the battery,
and composed of a battery attachment and battery.
The battery is charged by connecting the AC adapter with connecting to the
printer.
For details on how to attach it to the printer, refer to the manual that comes
with the Portable Kit.
Printable number of pages when using the battery: Approx. 110 pages (PP101 4" x 6" (101.6 x 152.4 mm))
* Page number was measured under the following conditions:
Battery: New battery, fully charged
Printing method: Continuous printing from an SD card at 23°C (73°F)
The printable number depends on the size and content of the photo data.
z Bluetooth Unit BU-20
The Bluetooth unit BU-20 is the unit which enables wireless printing from
Bluetooth compatible mobile phones or PDAs. For details on how to attach it
to the printer and print photos via Bluetooth communication, refer to the
User’s Guide on-screen manual.
To view the on-screen manual, double-click the XXX On-screen Manual alias
(where “XXX” is your printer’s name) on the desktop.
System Requirements
Browser: Help Viewer
Note
z The on-screen manual may not be displayed properly depending on your
operating system. We recommend that you keep your system up to date.
z We recommend using Safari as your Web browser to view the HTML format
on-screen manuals. If Safari is not installed on your computer, download it from
Apple Inc. website and install it.
Appendix
47
Specifications
Print Head
Printing resolution
(dpi)
Printer
9600 (horizontal)* × 2400 (vertical)
* Ink droplets can be placed with a horizontal pitch of 1/
9600 inch at minimum. Supported only when printing
with a computer.
USB 2.0 High Speed *1
IrDA ver.1.2 *2
Bluetooth 1.2 (Option) *2 *3
*1 A computer that complies with USB 2.0 Hi-Speed
standard is required.
Since the USB 2.0 Hi-Speed interface is fully upwardly
compatible with USB Full-Speed (USB 1.1), it can be
used at USB Full-Speed (USB 1.1).
2
* JPEG only
*3 Bluetooth connection is for printing only. This printer
cannot print data from a PC via Bluetooth
communication.
Print width
4.8 inches / 120.2 mm max.
(for Borderless Printing: 5 inches / 127 mm)
Acoustic noise level
Approx. 35.5 dB (A)
* When printing in the highest print quality mode on Photo
Paper Pro.
Operating environment Temperature: 5 to 35°C (41 to 95°F)
Humidity: 10 to 90% RH (no condensation)
Storage environment
Temperature: 0 to 40°C (32 to 104°F)
Humidity: 5 to 95% RH (no condensation)
Power supply
AC adapter 100-240 V, 50/60 Hz
Power consumption
Printing: Approx. 13 W
Standby: Approx. 2.2 W
OFF: Approx. 0.4 W
External dimensions
Approx. 10.2 (W) × 8.9 (D) × 3.2 (H) inches /
Approx. 258 (W) × 225 (D) × 81 (H) mm
* With the Paper Feed Tray and Paper Output Tray
retracted.
Weight
Approx. 2.5 kg (Approx. 5.4 lb.)
* With the Print Head and the ink tank installed.
External dimensions
Interface
48
Appendix
Weight
Rated input
Rated output
Paper size
Paper type
Layout
Image optimize
Print date/file no.
Trimming
Printer
Total 1,536 nozzles (C/M each 512 nozzles, Y/Dye BK
each 256 nozzles)
AC Adapter
Approx. 4.7 (W) x 2.3 (D) x 1.3 (H) inches / Approx. 118
(W) x 58 (D) x 32 (H) mm (excluding protruding portion)
Approx. 5.2 (W) x 2.3 (D) x 1.3 (H) inches / Approx. 130
(W) x 58 (D) x 32 (H) mm (including protruding portion)
Approx. 230 g (Approx. 8.2 oz.)
AC 100-240 V
DC 16 V, 2.0 A
Camera Direct Print (PictBridge)
4" x 6" / 101.6 x 152.4 mm, 5" x 7" / 127.0 x 177.8 mm*,
Credit card, Wide*
* Can be selected only on certain Canon-brand PictBridge
compliant devices.
Default (Selections based on the printer setting), Photo
(Photo Paper Plus Glossy, Glossy Photo Paper, Glossy
Photo Paper “Everyday Use”, Photo Paper Glossy, Photo
Paper Plus Semi-gloss, Photo Stickers), Fast Photo
(Photo Paper Pro)
Default (Selections based on the printer setting),
Borderless, Bordered, N-up (2, 4, 9, 16*)
* Layout compatible with Canon-brand sticker above. See
“About PictBridge Print Settings” on page 22.
You can print shooting Info (Exif Data) in the margins of
specified photos. Select Layout, then select the item
displayed with the [i] icon.
(Note that this print setting cannot be used for some
models.).
Default (Selections based on the printer setting), On,
Off, “VIVID”*, “NR” (Noise Reduction)*, “Face”*, “Red
eye”*
* If using a Canon PictBridge compliant camera, you can
select it.
Default (Off: No printing), Date, File No., Both, Off
Default (Off: No trimming), On (follow camera’s setting),
Off
Minimum System Requirements
Additional System Requirements for On-Screen Manuals
Note
Conform to the operating system’s requirements when higher than those given here.
Operating
System
Processor
RAM
Windows Vista
Pentium II (including
compatible processors)
300 MHz
128 MB
Windows XP SP1, SP2
Pentium II (including
compatible processors)
300 MHz
128 MB
Windows 2000 Professional
SP2, SP3, SP4
Pentium II (including
compatible processors)
300 MHz
128 MB
Note: Operation can only be
guaranteed on a PC
preinstalled
Windows Vista, XP or 2000.
Browser
Internet Explorer 6.0Hard Disk Space 400 MB
Note: For bundled software
installation.
CD-ROM Drive
Required
Other
SVGA 800 x 600
restrictions
Mac OS X v.10.4
Intel processor
PowerPC G3
256 MB
Browser: Windows HTML Help Viewer
Note: Microsoft Internet Explorer 5.0 or
later must be installed. The on-screen
manual may not be displayed properly
depending on your operating system or
Internet Explorer version. We
recommend that you keep your system
up to date with Windows Update.
Browser: Help Viewer
Note: The on-screen manual may not
be displayed properly depending on
your operating system or Help Viewer
version. We recommend that you keep
your system up to date with Software
Update.
Mac OS X v.10.2.8 - v.10.3
PowerPC G3
128 MB
Note: Hard disk must be
formatted as Mac OS
Extended (Journaled) or Mac
OS Extended.
Specifications are subject to change without notice.
Safari
200 MB
Note: For bundled software
installation.
To upgrade from Windows XP to Windows Vista, first uninstall software bundled
with the Canon inkjet printer.
Appendix
49
Safety Precautions
Cleaning the
printer
Please read the safety warnings and cautions provided in this manual to ensure
that you use the printer safely. Do not attempt to use the printer in any way not
described in this manual.
Always unplug the printer from the power outlet before cleaning the
printer.
If you accidentally switch the printer on while cleaning it, you could injure
yourself or damage the printer.
Warning
You may cause an electric shock, fire, or damage the printer if you ignore any of these
safety precautions.
Choosing a
location
Do not place the printer close to flammable solvents such as alcohol or
thinners.
Power supply Never attempt to plug in or unplug the printer from the power supply
when your hands are wet.
Always push the plug all the way into the power outlet.
Never damage, modify, stretch or excessively bend
or twist the power cord. Do not place heavy objects
on the power cord.
Use a damp cloth to clean the printer. Never use
flammable solvents such as alcohol, benzene or
thinners.
If flammable solvents come in contact with electrical
components inside the printer, it could cause a fire or
electric shock.
Maintaining
the printer
Do not attempt to disassemble or modify the printer. There are no user
serviceable parts inside the printer.
The printer contains high-voltage components. Never attempt any
maintenance procedure not described in this guide.
Working
around the
printer
Do not use highly flammable sprays near the printer.
This could cause a fire or electric shock if the spray comes into contact
with electrical components inside the printer.
Caution
You may cause injury or damage the printer if you ignore any of these safety precautions.
Never plug the printer into a power socket that is
shared with other equipment (extension lead/cord, 2or 3-way adapter, etc.).
Never use the printer if the power cord is bundled or knotted.
If you detect smoke, unusual smells or strange noises around the printer,
immediately unplug the printer at the power supply and call for service.
Periodically, unplug the printer and use a dry cloth to
wipe off any dust or dirt collected on the plug and the
power outlet. If the printer is placed at a location
exposed to a lot of dust, smoke, or high humidity, the
dust collected on the plug absorbs moisture and may
cause insulation failure and fire.
If you hear thunder, disconnect the power supply of the printer and refrain
from using it. Leaving the printer plugged in may cause fire, electric
shock, or damage to the printer, depending on the thunder storm.
Use the power cable included with the printer.
Use only power supplies listed in the user instructions (Canon AC
Adapter: K30285 and/or Li-ion Battery Pack: Canon K30274).
Do not use them for other products.
50
Appendix
Choosing a
location
Do not install the printer in a location that is unstable or subject to
excessive vibration.
Do not install the printer in locations that are very humid or dusty, in direct
sunlight, outdoors, or close to a heating source.
To avoid the risk of fire or electric shocks, install the printer in a location
with an ambient temperature range of 5°C to 35°C (41°F to 95°F) and
humidity of 10% to 90% (condensation free).
Do not place the printer on a thick rug or carpet.
Power supply Ensure that the area around the power outlet is kept
clear at all times so you can easily unplug the power
cord if necessary.
Never remove the plug by pulling on the cord.
Do not use an extension lead/cord.
Working
around the
printer
Never put your hands or fingers in the printer while it is printing.
Do not place any object on the printer.
Do not place metal objects (paper clips, staples, etc.) or containers of
flammable solvents (alcohol, thinners, etc.) on top of the printer.
If any foreign object (metal or liquid) fall into the printer, unplug the power
cord and call for service.
Do not transport or store the printer on a slant, vertically or upside-down,
as the ink may leak and damage the printer.
Print Head
and ink tank
For safety reasons, store Print Head and ink tank out of the reach of
small children.
If a child ingests any ink, consult a doctor immediately.
Do not shake Print Head or ink tank.
Ink may leak out and stain clothing or the surrounding area.
Never touch the electrical contacts on a Print Head
after printing. The metal parts may be very hot and
could cause burns.
During
printing
Do not touch the part around the ejecting paper during printing.
This could cause the printer to malfunction.
AC Adapter
When you pack the AC adapter for travel or storage, never wrap the cord
around the body of AC adapter to prevent the cord from splitting or
separating from the body of the AC adapter and causing a short circuit.
European Union (and EEA) only.
This symbol indicates that this product is not to be
disposed of with your household waste, according to the
WEEE Directive (2002/96/EC) and your national law. This
product should be handed over to a designated collection
point, e.g., on an authorized one-for-one basis when you
buy a new similar product or to an authorized collection
site for recycling waste electrical and electronic equipment
(EEE). Improper handling of this type of waste could have
a possible negative impact on the environment and human
health due to potentially hazardous substances that are
generally associated with EEE. At the same time, your
cooperation in the correct disposal of this product will
contribute to the effective usage of natural resources. For
more information about where you can drop off your waste
equipment for recycling, please contact your local city office, waste authority,
approved WEEE scheme or your household waste disposal service.
For more information regarding return and recycling of WEEE products, please
visit www.canon-europe.com/environment.
(EEA: Norway, Iceland and Liechtenstein)
For Customers in Europe, Middle-East, Africa
and Russia only
For Canon Customer Support contacts, please see the back cover of the European
Warranty Systems (EWS) Booklet or visit www.canon-europe.com.
Model Number: K10312 (mini320)
Appendix
51
Regulatory Information
FCC Notice (U.S.A. Only)
For 120V, 60Hz model
Model Number: K10312
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of a shielded cable is required to comply with Class B limits in Subpart B of
Part 15 of the FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise
specified in the manual. If such changes or modifications should be made, you
could be required to stop operation of the equipment.
Canon U.S.A., Inc.
One Canon Plaza
Lake Success, NY 11042
1-516-328-5600
52
Appendix
Canon U.S.A., INC. LIMITED WARRANTY --- (USA
Only)
The limited warranty set forth below is given by Canon U.S.A., Inc. (“Canon USA”)
with respect to the new or refurbished Canonbrand product (“Product”) packaged
with this limited warranty, when purchased and used in the United States only.
The Product is warranted against defects in materials and workmanship under
normal use and service (a) for a period of one (1) year from the date of original
purchase when delivered to you in new condition in its original container or (b) for
90 days from the date of original purchase for refurbished Products. Product
returned to a Canon USA repair facility or a Canon USA Authorized Service Facility
(“ASF”), and proven to be defective upon inspection will be (a) repaired utilizing
new, remanufactured, repaired and/or recycled parts (b) exchanged for new or; (c)
exchanged for a refurbished Product, as determined by the Canon USA repair
facility or the ASF. Warranty repair or replacement shall not extend the original
warranty period of the Product. A dated proof of purchase is required at the time of
warranty service. A copy of your dated bill of sale will satisfy this requirement. This
warranty does not cover any accessories, or any consumables, such as paper or
ink cartridges, as to which there shall be no warranty or replacement.
This limited warranty shall only apply if the Product is used in conjunction with
compatible computers, peripheral equipment and software. Canon USA shall have
no responsibility for such items except for compatible Canon brand peripheral
equipment covered by a separate warranty (“Separate Warranty”). Repairs of such
Canon brand peripheral equipment shall be governed by the terms of the Separate
Warranty. Non-Canon brand equipment and software that may be distributed with
the Product are sold “as is” and without warranty of any kind by Canon USA,
including any implied warranty regarding merchantability or fitness for a particular
purpose, and all such warranties are disclaimed. The sole warranty, if any, with
respect to such non- Canon brand items is given by the manufacturer or producer
thereof.
This limited warranty covers all defects encountered in normal use of the Product
and does not apply in the following cases:
(a) Loss of or damage to the Product due to abuse, neglect, mishandling, improper
packaging by you, alteration, accident, electrical current fluctuations, improper
use, failure to follow operating or maintenance instructions in, or environmental
conditions prescribed in, Canon USA’s user’s manual or other documentation,
or services performed by someone other than a Canon USA repair facility or
ASF. Without limiting the foregoing, dropping the Product, scratches, and
abrasions will be presumed to have resulted from misuse, abuse or failure to
operate the Product as set forth in the user’s manual or other documentation for
the Product.
(b) Use of parts, media, software or supplies (other than those sold by Canon
USA), including non-Canon ink cartridges or refilled ink cartridges, that cause
damage to the Product or cause abnormally frequent service calls or service
problems.
(c) If the Product has had its serial number or dating defaced, altered or removed.
ANY SYSTEM SOFTWARE (WHETHER FACTORY LOADED ON THE PRODUCT
OR CONTAINED ON THE SOFTWARE DISKETTES OR CD-ROMS ENCLOSED
WITH, OR ACCOMPANYING, THE PRODUCT), AND ANY UTILITY SOFTWARE,
DISTRIBUTED WITH OR FOR THE PRODUCT, IS SOLD "AS IS" AND WITHOUT
WARRANTY BY CANON USA. THE SOLE WARRANTY WITH RESPECT TO
SUCH SOFTWARE IS CONTAINED IN THE SOFTWARE MANUFACTURER'S
LICENSE AGREEMENT DISTRIBUTED THEREWITH, INCLUDING ANY
LIMITATIONS AND DISCLAIMERS THEREON. PLEASE CONTACT CANON USA
IMMEDIATELY IF YOU HAVE NOT RECEIVED A COPY OF THE SOFTWARE
MANUFACTURER'S LICENSE AGREEMENT.
NO IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, APPLIES
TO THE PRODUCT AFTER THE APPLICABLE PERIOD OF THE EXPRESS
LIMITED WARRANTY STATED ABOVE, AND NO OTHER EXPRESS WARRANTY
OR GUARANTY, EXCEPT AS MENTIONED ABOVE, GIVEN BY ANY PERSON
OR ENTITY WITH RESPECT TO THE PRODUCT SHALL BIND CANON USA, OR
ITS ASF. (SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU.) CANON USA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR
PROFITS, INCONVENIENCE, EXPENSE FOR SUBSTITUTE EQUIPMENT OR
SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, OR ANY
OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY
THE USE, MISUSE, OR INABILITY TO USE THE PRODUCT REGARDLESS OF
THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON
USA OR ITS ASF HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST CANON USA OR
ITS ASF BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE
PRODUCT CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE
FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE
OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR
PROPERTY ARISING OUT OF THE POSSESSION, USE, MISUSE, OR
INABILITY TO USE THE PRODUCT SOLD BY CANON USA NOT CAUSED
SOLELY AND DIRECTLY BY THE NEGLIGENCE OF CANON USA, OR ITS ASF.
(SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION
OR LIMITATION MAY NOT APPLY TO YOU.) THIS LIMITED WARRANTY SHALL
NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF
THE PRODUCT OR THE PERSON FOR WHOM IT WAS PURCHASED AS A
GIFT, AND STATES YOUR EXCLUSIVE REMEDY.
Canon USA offers a range of customer technical support* options:
z Interactive troubleshooting, e-mail technical support, the latest driver downloads
and answers to frequently asked questions (www.canontechsupport.com)
z Toll-free live technical support Monday—Saturday (excluding holidays) at 1-800828-4040
z Telephone Device for the Deaf (TDD-1-866-251-3752)
z Repair or Exchange Service Options:
In the event service is required for the Product during the limited warranty period,
Canon USA offers two hardware support options:
Authorized Service Facility Carry-In / Mail-In Service
Canon USA’s Carry-In/Mail-In Service provides repair or exchange, at Canon
USA’s option, through Canon USA’s Authorized Service Facility (ASF) network.
The name and telephone number of the ASF(s) near you may be obtained from
Canon USA’s Web site at www.canontechsupport.com or by calling the Canon
USA Customer Care Center at 1-800-828-4040, or any time while speaking to a
technical support person. A Product covered by this limited warranty will be
repaired or exchanged, as determined by Canon USA, and returned without
charge by the ASF.
InstantExchange Service **
A Canon Customer Care Center or ASF technician will attempt to diagnose the
nature of the problem and, if possible, correct it over the telephone. If the problem
cannot be corrected over the telephone, and you elect the InstantExchange
option, a reference number will be issued to you. You will be asked for the
Product serial number and other information pertaining to your Product and for a
ship-to location for the replacement Product (must include street address).
The Canon USA repair facility will ship out the replacement Product prepaid by
Canon USA. After receipt of the replacement Product (with instructions and a
prepaid waybill), follow the enclosed instructions on how to ship your product to
the Canon USA repair facility. Your Product must be returned in the shipping
carton in which the replacement Product was packed and include the reference
number, A COPY OF YOUR DATED PROOF OF PURCHASE (BILL OF SALE),
and a complete explanation of the problem. DO NOT INCLUDE ANY OTHER
ITEMS WITH THE YOUR PRODUCT IN THE RETURN SHIPPING CARTON,
AND BE SURE TO RETAIN YOUR PRINTHEAD, INK CARTRIDGE(S) AND
TANK(S).
InstantExchange Service exchanges your Product with a replacement Product,
which will normally be shipped the same day if your request for this service is by
3 p.m. E.T. Monday through Friday, except holidays. Canon USA does not
guarantee same day shipment in the event of the occurrence of factors beyond
Appendix
53
its reasonable control. The replacement Product you receive may be a
refurbished or reconditioned unit and will be covered for the balance of the period
remaining on your original limited warranty. NOTE THAT BY USING THIS
SERVICE YOU WILL KEEP THE REPLACEMENT PRODUCT THAT IS SENT
TO YOU. CANON USA WILL RETAIN THE PRODUCT THAT YOU ORIGINALLY
PURCHASED, WHICH SHALL BECOME THE PROPERTY OF CANON USA.
InstantExchange warranty program service is available only during the express
limited-warranty period for your Product and only in the continental United States,
Alaska and Hawaii during such period.
This limited warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.
* Support program specifics are subject to change without notice.
** InstantExchange warranty service is subject to the availability of refurbished or
new replacement units.
Canon U.S.A., Inc.
One Canon Plaza
Lake Success, NY 11042
USA
Canon is a registered trademark of Canon Inc.
©2007 Canon U.S.A., Inc. Canon is a registered trademark of Canon Inc. in the
United States and may also be a registered trademark in other countries.
54
Appendix
For California, USA only
This product contains an internal battery for backup purposes.
Included battery contains Perchlorate Material-special handling may apply.
See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/ for details.
For Canada only
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du
Canada.
Getting Help from Canon
Ordering Information
For additional supplies, use the following descriptions and order numbers.
Help Us Help You Better
Before you contact Canon, please record the following information.
Serial Number (located on the bottom of the product): ______________________________________________________________________________________________
Model Number (located on the top of the product): _________________________________________________________________________________________________
Setup CD-ROM number (located on the CD-ROM): ________________________________________________________________________________________________
Purchase Date: ____________________________________________________________________________________________________________________________
Customer Technical Support Sequence*
1. Internet — www.canontechsupport.com
For quick and comprehensive self-help in an intuitively guided interactive troubleshooting environment, the place to start is our helpful tech support web site. In addition,
the latest driver downloads, answers to frequently asked questions, product information, and “where to buy” instructions are found here.
2.
Email Tech Support — www.canontechsupport.com
For individual attention to a special issue, try emailing our friendly technical support representatives, specially trained to communicate quick, easy, and logical solutions
to your inquiries within 24 hours.
3.
Toll-Free Live Tech Support — (1-800-828-4040)
This option provides live telephone technical support, free of service charges, Monday-Saturday (excluding holidays), during your product’s 1 year limited warranty
period. Telephone Device for the Deaf (TDD) support is available at (1-866-251-3752).
4.
Extended Service and Support — www.canonesp.com
Canon CarePAK Extended Service Plan is a cost-attractive and easy-to-use extended service program that provides up to three full years of service and support
coverage at a very attractive price. CarePAK offers toll-free Canon technical support and includes Canon’s superb InstantExchange product replacement program. For
further information about extending your Canon service and support, call (1-800-385-2155), or visit our Web site at www.canonesp.com. CarePAK must be purchased
during your product’s warranty period.
For more information and updated program specifics, please visit our web site at www.canontechsupport.com.
*Support program specifics are subject to change without notice.
Description
Order #
Ink Tanks
CLI-36 Color
1511B002
Canon Specialty Papers
All Occasion Photo Cards (4" x 8"/ 50 sheets)
Glossy Photo Paper Credit Card Size (100 sheets)
Matte Photo Paper (4" x 6"/ 120 sheets)
Photo Paper Glossy (4" x 6"/ 50 sheets)
Photo Paper Glossy (4" x 6"/ 100 sheets)
Photo Paper Plus Double Sided (5" x 7"/ 10 sheets)
Photo Paper Plus Double Sided Album Kit (5" x 7")
Photo Paper Plus Glossy (4" x 6"/ 20 sheets)
Photo Paper Plus Glossy (4" x 6"/ 50 sheets)
Photo Paper Plus Glossy (4" x 6"/ 120 sheets)
Photo Paper Plus Glossy (5" x 7"/ 20 sheets)
Photo Paper Plus Semi-gloss (4" x 6"/ 50 sheets)
Photo Paper Pro (4" x 6"/ 20 sheets)
Photo Paper Pro (4" x 6"/ 75 sheets)
Photo Stickers (16 stickers/sheet, 5 sheets/pack)
1029A069
9157A023
7981A014
0775B021
0775B022
9981A006
0041B005
7980A007
7980A012
7980A022
7980A019
1686B014
1029A014
1029A027
0001C001
Call 1-800-OK-CANON to locate a dealer near you, or visit the Canon eStore at
www.estore.usa.canon.com.
© 2007 Canon U.S.A., Inc. Canon is a registered trademark of Canon Inc. in the United States and may be a registered trademark or trademarks in other countries. All other
product and brand names are trademarks of their respective owners. As an ENERGY STAR® partner, Canon U.S.A., Inc. has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Photo Printer
series
Direct Photo Guide
Table of Contents
The following ink tank is compatible with this printer.
For information on product specifications, please visit our website at
www.usa.canon.com
QT5-1042-V01
XXXXXXXX
© CANON INC. 2007
PRINTED IN XXXXXXXX
Introduction
1
How to Use the Documentation Provided
2
Printer Parts and Their Functions
3
Loading Printing Paper
8
Printing from a Memory Card
10
Printing Photographs Directly from a Compliant Device
21
Printing Photographs from a Wireless Communication Device
25
Routine Maintenance
27
Changing the Printer Settings
33
Troubleshooting
35
Appendix
47
Download PDF

advertising