Canon 4204B019 All in One Printer User Manual

USER’S GUIDE
V:1153-1008-10
TDE2480
24” Class TV/DVD Combo
For the most up-to-date version of this User’s Guide, go to www.gpx.com
Warnings and Precautions
• CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
• WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
• AVERTISSEMENT: Pour réduire le risque d’incendie
ou de choc électrique, ne pas exposer cet appareil sous la
pluie et l’humidité.
• CAUTION: Use of controls or adjustments or
performance of procedures other than those specified
may result in hazardous radiation exposure.
• WARNING: Changes or modifications to this unit
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
• WARNING: Do not place the unit on top of any soft,
porous, or sensitive surfaces to avoid damaging the
surface. Use a protective barrier between the unit and
surface to protect the surface.
• WARNING: Use of this unit near fluorescent lighting
may cause interference regarding use of the remote. If
the unit is displaying erratic behavior move away from
any fluorescent lighting, as it may be the cause.
• CAUTION: Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent type.
• PRÉCAUTION: Danger d’explosion si les piles sont
remplacées de façon incorrect. Remplacer les piles
seulement par le même type de pile ou l’équivalent.
• WARNING: There is a danger of explosion if you
attempt to charge standard Alkaline batteries in the unit.
Only use rechargeable NiMH batteries.
• WARNING: The remote control’s button cell battery
contains mercury. Do not put in the trash, instead recycle
or dispose of as hazardous waste
• WARNING: Lithium batteries, like all rechargeable
batteries are recyclable and should be recycled or
disposed of in normal household waste. Contact your
local government for disposal or recycling practices in
your area. They should never be incinerated since they
might explode.
• WARNING: Shock hazard - Do Not Open.
• AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS
OUVRIR
Mains plug is used as disconnect device and it should
remain readily operable during intended use. In order
to disconnect the apparatus from the mains completely,
the mains plug should be disconnected form the mains
socket outlet completely.
La prise du secteur est utilisé pour déconnecter le
système.
La prise du secteur ne doit pas être obstruée ou doit être
facilement accessible pendant son utilisation. Pour être
complètement déconnecté de l’alimentation d’entrée, la
prise doit être débranchée du secteur.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or
rechargeable (ni-cad, ni-mh, etc) batteries.
No mezcle baterías viejas y nuevas.
No mezcle baterías alcalinas, estándar (carbono-zinc) o
recargables (ni-cad, ni-mh, etc.).
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE D' ÉLECTROCUTION
NE PAS OUVRIR
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
This product utilizes a Class 1 laser to read
Compact Discs. This laser Compact Disc Player is
equipped with safety switches to avoid exposure
when the CD door is open and the safety interlocks
are defeated. Invisible laser radiation is present
when the CD Player’s lid is open and the system’s
interlock has failed or been defeated. It is very
important that you avoid direct exposure to the
laser beam at all times. Please do not attempt to
defeat or bypass the safety switches.
2
GPX
Important Safety Instructions
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding - type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
When the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12.
Use only with a cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
Customer Support: 1-888-999-4215
FCC Warnings
WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Additional Warnings
• The apparatus shall not be exposed to dripping or splashing and
that no objects filled with liquids, such as vases, shall be placed on
apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux
éclaboussures et aucun objet ne contenant de liquide, tel qu’un
vase, ne doit être placé sur l’objet.
• Main plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus
from the mains completely, the mains plug should be disconnected
form the mains socket outlet completely.
La prise du secteur ne doit pas être obstruée ou doit être facilement
accessible pendant son utilisation. Pour être complètement
déconnecté de l’alimentation d’entrée, la prise doit être débranchée
du secteur.
• Battery shall not be exposed to excessive heat such as sunshine, fire
or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la
lumière du soleil, au feu ou autres choses de semblable.
• Caution marking is located at the rear or back of the apparatus.
Attention marquage est situé à l’arrière ou à l’arrière de l’appareil
• The marking information is located at the rear or back of apparatus.
Les informations de marquage est situé à l’arrière ou à l’arrière de
l’appareil.
This product incorporates copyright protection technology that is protected
by U.S. patents and other intellectual property rights. Use of this copyright
protection technology must be authorized by Rovi Corporation, and is intended
for home and other limited viewing uses only unless otherwise authorized by
Rovi Corporation. Reverse engineering and disassembly are prohibited.
GPX
3
24” Class TV/DVD Combo
Features
Included
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
23.6” LED display
DVD player: DVD, DVD±R/RW
CD player: CD, CD-R/RW, JPEG CD
Resolution: 1920 x 1080
Max color: 16.7 million
Brightness: 300 cd/m2
Contrast: 1000 : 1
Response time: <5ms
Viewing angle: H=170, V=160
V-chip
Closed captioning
Electronic program guide
Sleep timer
Multi-language OSD
RF input
2 HDMI inputs
2 RCA audio inputs
VGA/PC video input
3.5mm PC audio input
2 Composite video inputs
2 Component video inputs
USB port
Memory card reader
AC power: requires an AC power cable
(included)
•
Stand and 3 screws
Remote control: requires 2 AAA batteries
(included)
AC power cable
* Please note, LCD panel specifications are subject to change without notice.
4
GPX
Table of Contents
24” Class TV/DVD Combo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features
Included
Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power
Remote Power
Connecting the Stand
Television Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting a TV Antenna
Connecting Basic Cable
Connecting a Set-Top Box
Auto Scanning for Channels
Television. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Channel List
Saving a Channel as a Favorite
Viewing Favorites
Parental Controls
Accessing the TV Menu
Setting the Clock
DVD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Loading and Playing a Disc
Programming a DVD
Accessing the DVD Setup Menu
Memory Card Reader. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Connecting a Memory Card
Accessing the Connected Memory Card
USB Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Connecting a USB Thumb Drive
Accessing the Connected USB Thumb Drive
Connecting Other Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connecting a Set-Top Box
Connecting a Gaming Device
Connecting a DVD Player or VCR
Connecting a Computer
Company Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
International Support
Contact Information
Green Initiative
Customer Support: 1-888-999-4215
GPX
5
Introduction
EJECT
Press to eject
the loaded
disc.
PLAY/PAUSE EJECT
PLAY/PAUSE
Press to play or
pause a loaded
disc.
VOLUME ±
Press to adjust
the volume.
CHANNEL ±
Press to adjust
the television
channel.
MENU
Press to view
the television
menu.
STEREO
HEADPHONE
JACK
SOURCE
Press to adjust
between
the available
sources.
POWER
Press to power
the television
off or on.
USB PORT
RCA STEREO
AUDIO INPUT 2
DISC DRIVE
Pb
COMPONENT
VIDEO INPUT 2
3.5mm PC AUDIO
INPUT
RCA STEREO
AUDIO INPUT 1
L
AUDIO IN 1
R
PC
AUDIO
Y
VIDEO INPUT 2
Pr
VIDEO 2
L
AUDIO IN 2
R
COMPOSITE
VIDEO INPUT 2
USB
DRIVE
VIDEO INPUT 1
Y
Pb
Pr
TV ANTENNA
VIDEO 1
AC IN
COMPOSITE
VIDEO INPUT 1
RF INPUT
COMPONENT
VIDEO INPUT 1
VGA/PC VIDEO
INPUT
HDMI INPUTS
AC POWER
INPUT
6
GPX
SERVICE PORT
Used for
firmware
upgrades.
MEMORY
CARD READER
EJECT
Press to eject a disc from the DISC DRIVE.
NUMBER KEYPAD
EJECT
POWER
DISPLAY
Press to view the on-screen display.
MUTE
16:9/4:3/FAV LIST
Press to adjust the aspect ratio. Press to
access your favorites list on the television.
PICTURE
VOLUME
Press to adjust the volume.
SOUND
SOURCE
Press to adjust the source.
SLEEP
ARROW/ENTER
Press to navigate DVD and system menus,
and to make selections.
VOLUME
ZOOM
FAV LIST
CH LIST
ASPECT
Press to adjust the aspect ratio.
CC
Press to turn closed captioning off or on.
BACKWARD/FORWARD
Press to search through an individual
chapter or track.
STOP
Press to stop a disc during play.
PROG
Press to program a loaded disc to play titles,
chapters, or tracks in a specified order.
PLAY/PAUSE
Press to play or pause a loaded disc.
SUBTITLE
Press to adjust the current subtitle settings
for the loaded DVD.
ANGLE
Press to view alternate angles on supported
DVDs.
TITLE
Press to view the title menu on the loaded
DVD.
SOUND
Press to adjust the sound settings.
SLEEP
Press to set the sleep timer.
CHANNEL
Press to adjust the channel.
MENU
SOURCE
PICTURE
Press to adjust the picture settings.
CHANNEL
DISPLAY
SAP
In TV mode, press to switch to an alternate
audio option when supported.
MUTE
Press to mute the volume.
ZOOM/CHANNEL LIST
Press to zoom in or out on a loaded DVD.
Press to view a list of available channels on
the television.
DVD
16:9/4:3
POWER
Press to turn the television off and on.
MENU
Press to access the TV’s menu.
EXIT
Press to exit the current on-screen menu.
ENTER
SAP
EXIT
GUIDE
Press to view the on-screen guide.
USB/SD
Press to access USB and SD modes.
CC
ASPECT
GUIDE
USB/SD
BACKWARD
FORWARD
PREVIOUS
NEXT
STOP
PLAY/PAUSE DVD MENU
DVD SETUP
PROG
ANGLE
A-B
GOTO
SUBTITLE
TITLE
AUDIO
REPEAT
PREVIOUS/NEXT
Press to skip between chapters or tracks on
the loaded disc.
DVD MENU
Press to access the loaded DVD’s menu.
DVD SETUP
Press to access the DVD setup menu.
GOTO
Press to go to a specified title, chapter,
track, or time on the loaded disc.
REPEAT
Press to repeat a title, chapter, track, or
entire disc.
AUDIO
Press adjust the current audio settings for
the loaded DVD.
A-B
Press to create a repeating loop on a
specified section of a loaded DVD.
Customer Support: 1-888-999-4215
GPX
7
Setup
Power
Pb
L
AUDIO IN 1
R
PC
AUDIO
Y
VIDEO INPUT 2
Pr
VIDEO 2
L
AUDIO IN 2
R
Plug the attached AC cord into a standard AC
power outlet to power the television.
Remote Power
Requires 2, AAA size, batteries (included)
OPEN
Connecting the Stand
Requires stand and 3 machine screws
(all included)
1. Insert a single machine screw through
the bottom of the stand and up into the
television. Tighten by hand using a philipshead screw driver.
2. Insert the remaining two screws through
the back of the stand and into the television.
Tighten by hand using a philips-head screw
driver.
8
GPX
USB
DRIVE
VIDEO INPUT 1
Y
Pb
Pr
TV ANTENNA
VIDEO 1
AC IN
Television Setup
Connecting a TV Antenna
Connecting a Set-Top Box
Requires a TV antenna (not included).
Requires a Set-Top Box (not included).
1. Connect a VHF, UHF, or HDTV antenna to the
RF INPUT on the television.
If your Set-Top Box has an HDMI Output:
• Connect the HDMI output on the Set-Top Box
to the HDMI INPUT on the television using
an HDMI cable (not included).
The Auto Channel Scan must be run before any
channels can be viewed on the television.
2. Press the SOURCE button and switch to TV
mode.
3. Press the MENU button.
4. Use the ARROW buttons to select Channel in
the on-screen menu. Press the ENTER button.
5. Use the ARROW buttons to select Signal Type
in the on-screen menu. Press the ARROW
buttons to change the Signal Type to Air.
6. Use the ARROW buttons to select Auto
Channel Search in the on-screen menu. Press
the ENTER button to automatically scan for
available channels.
Connecting Basic Cable
Requires a cable connection.
1. Connect a cable to the RF INPUT on the
television.
The Auto Channel Scan must be run before any
channels can be viewed on the television.
2. Press the SOURCE button and switch to TV
mode.
3. Press the MENU button.
4. Use the ARROW buttons to select Channel in
the on-screen menu. Press the ENTER button.
5. Use the ARROW buttons to select Signal Type
in the on-screen menu. Press the ARROW
buttons to change the Signal Type to Cable.
6. Use the ARROW buttons to select Auto
Channel Search in the on-screen menu. Press
the ENTER button to automatically scan for
available channels.
Customer Support: 1-888-999-4215
If your Set-Top Box has a Composite Video
Output:
• Connect the video output on the Set-Top
Box to the COMPOSITE VIDEO INPUT on
the television using an A/V RCA cable (not
included). Connect the audio output on the
Set-Top Box to the RCA STEREO AUDIO
INPUT on the television.
If your Set-Top Box has a Component Video
Output:
• Connect the component video output on
the Set-Top Box to the COMPONENT VIDEO
INPUTS on the television using a component
RCA cable (not included). Connect the
audio output on the Set-Top Box to the RCA
STEREO AUDIO INPUT on the television.
After connecting your Set-Top Box:
• Press the SOURCE button to switch between
TV, AV 1 or 2, YPbPr 1 or 2, HDMI 1 or 2, and
VGA to match the connection used.
Auto Scanning for Channels
The Auto Channel Scan must be run before any
channels can be viewed on the television.
1. Press the SOURCE button and switch to TV
mode.
2. Press the MENU button.
3. Use the ARROW buttons to select CHANNEL
in the on-screen menu. Press the ENTER
button.
4. Use the ARROW buttons to select Auto
Channel Search in the on-screen menu. Press
the ENTER button to automatically scan for
available channels.
GPX
9
Television
Channel List
Parental Controls
Press the CHANNEL LIST button on the remote
to view a list of available channels on the
television.
1. In TV mode, press the MENU button.
If there are no channels in your channel list, you
may need to re-run the Auto Scan for Channels.
(see page 9)
Saving a Channel as a Favorite
1. In TV mode, press the MENU button.
2. Use the ARROW buttons to select Channel in
the on-screen menu. Press the ENTER button.
3. Use the ARROW buttons to select Channel
Setting in the on-screen menu. Press the
ENTER button.
4. Use the ARROW buttons to select the
Channel Number you want to save as a
favorite.
5. Use the ARROW buttons to select Favorite
Channel. Press the ENTER button to save the
selected channel as a favorite.
2. Use the ARROW buttons to select Parental
Control in the on-screen menu. Press the
ENTER button.
3. The default passcode for the parental lock is: 0000
From the V-CHIP settings you can lock TV and
movies that have specific ratings.
Use the Front Panel Lock to lock the buttons on
the television. (The remote will still work if the
Front Panel Lock is checked)
Accessing the TV Menu
1. In TV mode, press the MENU button.
To exit the TV menu, press the EXIT button on
the remote.
Setting the Clock
1. In TV mode, press the MENU button.
Viewing Favorites
2. Use the ARROW buttons to select Setup in
the on-screen menu. Press the ENTER button.
1. In TV mode, press the FAVORITES LIST
button on the remote to access your favorites
list on the television.
3. Use the ARROW buttons to select Clock in
the on-screen menu. Press the ENTER button.
2. Use the ARROW/ENTER buttons to highlight
and select a channel from the favorites list.
4. Use the ARROW buttons to select your time
zone.
5. Use the ARROW buttons to highlight Setup
Time.
6. Use the left and right ARROW buttons and
ENTER button to adjust and save the date
and time.
10
GPX
DVD
Loading and Playing a Disc
1. Press the SOURCE button to switch to DVD
mode.
2. Insert a DVD or CD into the DISC DRIVE, labelside facing the rear of the TV.
The loaded disc will begin playing
automatically.
3. If the loaded disc does not automatically
play, press the PLAY/PAUSE button.
Programming a DVD
1. Follow the instructions for Loading and
Playing a Disc.
2. Press the PROGRAM button on the remote.
3. Use the NUMBER KEYPAD and ARROW
buttons to enter title (TT) and chapters (CH)
from the loaded DVD in the order you want
them to play.
Disc title and chapter information can be
obtained by pressing the DISPLAY button
during DVD playback.
4. Press the PLAY/PAUSE button or use the
ARROW buttons to highlight the on-screen
PLAY button and press ENTER to begin
playing the programmed DVD.
Accessing the DVD Setup Menu
1. To access the DVD Setup Menu, press the
DVD SETUP button on the remote.
To exit the DVD setup menu, press the DVD
SETUP button.
Customer Support: 1-888-999-4215
GPX
11
Memory Card Reader
Connecting a Memory Card
MMC
1. Load an SD, MS, or MMC memory card into
the MEMORY CARD READER as shown in
the image to the right.
Accessing the Connected Memory Card
SD
1. Follow the instructions for Connecting a
Memory Card.
2. Press the SOURCE button to switch to DVD
mode.
4. Use the ARROW/ENTER buttons to select
and play content from the connected
memory card.
12
GPX
MS
3. Press the USB/SD button on the remote to
switch to CARD mode.
USB Port
Connecting a USB Thumb Drive
1. Connect a USB thumb drive to the USB PORT
as shown in the image to the right.
Accessing the Connected USB Thumb Drive
1. Follow the instructions for Connecting a USB
Thumb Drive.
2. Press the SOURCE button to switch to DVD
mode.
3. Press the USB/SD button on the remote to
switch to USB mode.
4. Use the ARROW/ENTER buttons to select
and play content from the connected USB
thumb drive.
Customer Support: 1-888-999-4215
GPX
13
Connecting Other Devices
Connecting a Set-Top Box
Connecting a DVD Player or VCR
•
•
•
•
•
•
You will need: a DVD player or VCR,
composite and RCA stereo cables or
component and RCA stereo cables or an
HDMI cable.
Connect the DVD player or VCR’s audio and
video outputs to the corresponding audio and
video inputs on the television.
Press the SOURCE button to switch between
TV, AV 1 or 2, YPbPr 1 or 2, HDMI 1 or 2, and
VGA to match the connection used.
Connecting a Gaming Device
Connecting a Computer
•
•
•
•
14
You will need: a set-top box, composite
and RCA stereo cables or component and
RCA stereo cables or an HDMI cable. (not
included)
Connect the set-top box’s audio and video
outputs to the corresponding audio and
video inputs on the television.
Press the SOURCE button to switch between
TV, AV 1 or 2, YPbPr 1 or 2, HDMI 1 or 2, and
VGA to match the connection used.
GPX
You will need: a gaming device, composite
and RCA stereo cables or component and
RCA stereo cables or an HDMI cable. (not
included)
Connect the gaming device’s audio and video
outputs to the corresponding audio and
video inputs on the television.
Press the SOURCE button to switch between
TV, AV 1 or 2, YPbPr 1 or 2, HDMI 1 or 2, and
VGA to match the connection used.
•
•
•
You will need: a PC with a VGA output, and a
VGA cable. (not included)
Connect the computer’s VGA output to the
VGA/PC INPUT on the television.
Power the television on and press the
SOURCE button to switch to the VGA Mode.
Audio from the connected PC can be input
to the television through the TV’s PC AUDIO
INPUT by using a 3.5mm audio cable (not
included).
Customer Support: 1-888-999-4215
GPX
15
Company Information
International Support
To download this User’s Guide in English,
Spanish, or French, visit the support section at
www.gpx.com.
Para transferir esta guía de usuario en inglés,
español, o francés, visite la sección de la ayuda
en www.gpx.com.
Pour télécharger ce guide de l’utilisateur en
anglais, espagnol, ou français, visitez la section
de soutien chez www.gpx.com.
Contact Information
Phone:
1-888-999-4215
Email:
prodinfo@gpx.com
Parts Email:
partsinfo@dpi-global.com
Website:
www.gpx.com
Green Initiative
Environmental Commitment to ‘Protect for Today
and Sustain for Tomorrow’
2009 marked the official launch of DPI, Inc.’s
corporate campaign for a greener and cleaner
world. DPI is building upon environmental
initiatives introduced at all of their facilities
to help formulate and sustain significant and
important conservation efforts within its
manufacturing and marketing communities.
In addition to targeting and selecting energy
efficient product features, and structuring ‘green
office’ procedures, other initial program efforts
include:
•
•
•
•
Reduction of all packaging sizes
Recyclable plastics for clamshell packages,
with a plan to eventually replace plastic with
recyclable paper
Recycled fiber board in place of the polyfoam
in packing boxes
Recycled plastics in place of the virgin
material in product construction
Copyright © 2010 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners.
Specifications are subject to change without notice