Star Manufacturing B710H Operation Manual

OPERATOR'S MANUAL

HOLMAN CONVEYOR TOASTERS

MODELS T710(H, TW, TX) T714(H, TW, TX) S710(H) S714(H) B710H

FOR SERVICE INFORMATION

U.S. AND CANADA CALL: 1-800-807-9054

24 HOURS/DAY 7 DAYS/WEEK

TABLE OF CONTENTS

UNCRATING AND INSPECTION PAGE 1

ASSEMBLY AND INSTALLATION

POWER SAVER SWITCH

SECURITY FEATURES

CLEANING PROCEDURES

PAGE 1

PAGE 2

PAGE 2A

PAGE

PAGE 4

TROUBLESHOOTING GUIDE

MAINTENANCE PROCEDURES

PAGE 5, 6

PAGE 7, 8, 9

PARTS LIST/EXPLODED VIEW PAGE 10, 11, 12, 13

DRAWINGS

CRUMB TRAY

LOAD AND UNLOAD TRAYS

ADJ. HEAT SHIELD, FRONT VIEW

COMPONENT ARRANGEMENT

HEATER TUBE INSTALLATION

DRIVE SYSTEM

WIRING DIAGRAMS [T710(H,TW)]

PAGE 1

PAGE 1

PAGE 3

PAGE 6

PAGE 7

PAGE 9

PAGE 15, 16

WIRING DIAGRAMS [T714(H,TW)]

WIRING DIAGRAMS [B710(H)]

PAGE 16, 17

PAGE 18

WIRING DIAGRAMS [S710(H), Jamba Juice] PAGE 19

WIRING DIAGRAMS [S714(H)] PAGE 20

REV. 12/6/2005 RMS

HG0102




UNCRATING AND INSPECTION

Unpack unit and components from container. Remove all visible packing material, inspect unit for damage. If damage is discovered, file a claim immediately with the carrier that handled the shipment.

ASSEMBLY AND INSTALLATION

A. Attach legs by screwing into weld nuts, as shown below.

Page 1

ADJUSTABLE LEG: SCREWS INTO WELD NUT LOCATED

AT EACH CORNER ON BOTTOM SIDE OF TOASTER

LEVELING OF THE TOASTER CAN BE DONE BY TURNING

THE FOOT SECTION OF THE LEG COUNTER CLOCKWISE

B. Anti Skid pads are available at no charge and may be adhered to the foot section of each leg to prevent sliding. Call 1-800-225-3958 for details.

WARNING: the National Sanitation Foundation does not approve Use of these pads.

C. Place load and unload trays as shown below.

LOAD UP TRAY

CAUTION: DO NOT OPERATE UNIT WITHOUT

CRUMB TRAY PROPERLY POSITIONED

AS THIS WILL CAUSE OVERHEATING IN THE

CONTROL BOX.

HEAT REFLECTOR / CRUMB TRAY

TOAST CHUTE

(REAR DISCHARGE)

TOAST CHUTE

WARNING: MAKE SURE ALL INPUT POWER IS OFF BEFORE INSTALLING/REMOVING

ANY PARTS.

WARNING: BEFORE INSTALLING UNIT(S), CHECK WITH LOCAL POWER COMPANY TO

DETERMINE ACTUAL VOLTAGE AT JOB SITE. NEVER PLUG A 208-VOLT UNIT

INTO 240 VOLTS OR A 240 VOLT UNIT INTO 208 VOLTS.

WARNING: BE ABSOLUTELY SURE THE GROUND CONNECTION FOR THE RECEPTACLE

IS PROPERLY WIRED. NEVER CONNECT UNIT TO POWER WITHOUT

PROPER GROUND CONNECTIONS. IMPROPER GROUND MAY RESULT IN

SEVERE INJURY OR FATALITY.

REVISED 4-15-96 MJC

Page 2




OPERATION

Your Holman toaster may be equipped with a Power Saver Switch, details are as follow;

POWER SAVER

SWITCH

FULL

POWER

TOGGLE POWER SAVER

OFF

1/4 POWER

STAND BY

FULL POWER

OFF OFF

1/4 POWER

STAND BY

ROTARY POWER SAVER

Power Saver

Switch Positions

FULL POWER-

OFF-ROTARY:

OFF-TOGGLE:

STANDBY-

When in this position your unit is at Full Power and ready to use.

Adjust the Top and Bottom Variable Heat Controls and Conveyor

Belt Speed Control to your desired settings.

Two off positions are provided so that a single rotation to either direction will result in the unit being turned OFF.

The center position of the toggle switch turns the unit completely

OFF regardless of heat and speed control settings.

The standby position reduces the power to the unit to 1/4, and therefore saves 75% of the energy consumption. In this position your unit will stay warm and reduce the reheat time when switched to Full Power to 20 to 30 seconds.

REV. 1/28/97 MJC

FULL KEY LOCKING COVER

FITS OVER CONTROLS AND

SIDE PANELS TO PREVENT

TAMPERING

Fig. 1

SECURITY TOAST

CHUTE MOUNTING

ROD

S710CHUT.WMF

Fig. 2

COTTER PIN

S710LOK.WMK

HOLMAN

S710LEG.WMF

SECURITY COUNTER MOUNTING

BRACKET ATTACHES TO LEG FOOT

AND IS SECURED TO COUNTER

WITH A SCREW.

COTTER PIN

LEG SCREWS

INTO THE BOTTOM

OF TOASTER

KEY LOCK

Fig. 3

MOUNTING

BRACKET

FOOT SCREWS

INTO BOTTOM

OF LEG

Page 2A



MODELS S710(H), S714(H)

HOLMAN

SECURITY COVER :

Your Holman models S710 and S714 are quipped with a full front key locking cover (fig.1).

This over fits over the front and sides of the unit.

The security cover must be removed with a key in order to gain access to the controls, side panels, legs and toast chute to be removed.

To remove, unlock the cover using the key. Pull locked side of cover out and away from the unit.

The right side will release at the same time.

To replace the cover, Hook the right side of the cover over the latch on right front of the unit while sliding the left side of the cover over the lock. Secure cover using key.

TOAST CHUTE MOUNTING ROD

SLIDES THOUGH MOUNTING HOLE

IN CHASSIS AND THROUGH LOOP IN

TOP OF TOAST CHUTE

TOAST CHUTE ;

To install the toast chute (fig. 2), Remove the left side panel by removing two screws and pulling the top part of the panel out while lifting up.

Remove the mounting rod by sliding it through chassis.

Next, place the toast chute beneath toaster as shown. Line up the looped end of toast chute with holes in the rear of toaster as shown. Insert mounting rod through the holes in chassis and the toast chute (If legs have not been installed, do so now).

Reinstall side panel and secure with screws.

Toast chute is now ready for use.

LEGS :

To secure the toaster to the counter (fig.3),

Remove both side panels by removing two screws and pulling the top of the panel out while lifting up. Unscrew the foot of each leg and slide counter-mounting brackets onto the legs. Screw the foot back onto each leg and install legs onto the toaster. Place the small cotter pin through the holes in threaded portion of each leg.

Secure the mounting brackets to the counter with a screw or bolt. Reinstall both side panels and secure with screws.

NOTE: Security models are not supplied with a power saver switch.

REV. 1/28/97 MJC

PAGE 3




COOKING PROCEDURES

A. BREAD TOASTING

NOTE: Models TX710(H) and TX714(H) have an extended conveyor belt in lue of a load up tray. Place (do not press) the product on the extended conveyor belt for toasting or heating. Follow the instructions listed below for cooking and operation procedures.

1. On models T710H, TX710(H), T714H, TX714(H) and B710H, S710(H),

S714(H) lower the front heat shield all the way down, leave just enough clearance for bread slices to pass under the shield into the cooking cavity (See illustration below).

ADJUSTABLE HEAT SHUTTER

2. Turn top and bottom heat controls to HI; turn conveyor speed control to

50.

3. Allow warm up time of 5 to 10 minutes.

4. Test with a slice of bread. a. If toast is too light, turn conveyor speed control counterclockwise to a

slower b. If toast is too dark, turn conveyor speed control clockwise to a faster

speed.

B. MODELS T710(H), TX710H, T714(H), TX714H, S710(H), S714(H)-BUN TOASTING

1. Buns may be top or bottom toasted. Turn appropriate heat control to HI, set conveyor speed control to 50.

2. On models with high (3") clearance (T710H, TX710H, T714H, TX714H, S710H,

S714H), lower the front heat shield as far as possible, leave just enough clearance for the bun half to pass under and into the cooking cavity.

3. Test with a half of a bun. a. If bun half is too light, turn conveyor speed control counterclockwise

to b. If bun half is too dark, turn conveyor speed control clockwise to a

faster

Cooking procedures continued on page 4

REVISED 7/29/97 MJC

PAGE 4




COOKING PROCEDURES CONT.

C.

The model B710(H) has higher wattage tubes on the top than on the bottom, therefore when placing the bun halves on the conveyor you should place them cut side up.

D. DEEP TOASTING OR BAKING (Units with Variable Heat Controls).

Food products that require deep heating without exterior toasting may be heated by reducing the oven temperature (lowering the top and/or bottom heat controls) and cooking at slower speeds. Some foods may require more top heat than bottom heat or vice versa. Every product will require some experimentation to arrive at the correct balance of heat control and conveyor speed settings. Each time a setting is changed allow about 5 minutes for the unit to stabilize.

CLEANING PROCEDURES

1. Turn top and bottom heat controls to the OFF position.

2. For lightly soiled conveyor belts, turn conveyor speed control to fastest setting (100) and wipe with a damp cloth.

3. For heavily soiled conveyors, turn conveyor speed control to fastest setting

(100) and wipe with a light abrasive pad.

4. Turn conveyor speed control off.

5. After the unit cools, remove interior crumb tray (as shown below) and clean.

Slide crumb tray back into position. DO NOT OPERATE UNIT WITHOUT

CRUMB TRAY IN PLACE AS THIS CAUSES OVERHEATING IN THE

CONTROL BOX AND MAY ACTIVATE THE HEAT LIMIT SWITCH.

6. Wipe exterior surface of unit.

LUBRICATION OF DRIVE CHAIN WITH A GRAPHITE BASED LUBRICANT IS REQUIRED AS

PERIODIC MAINTENANCE. CALL HOLMAN FACTORY SERVICE DEPARTMENT FOR

DETAILS.

LOAD UP TRAY

CAUTION: DO NOT OPERATE UN

WITHOUT CRUMB TRAY AS

THIS CAUSES OVERHEATING IN

THE CONTROL BOX.

IDLER SHAFT

DRIVE SHAFT

CONVEYOR LINK, MODEL T710

HEAT REFLECTOR / CRUMB TRAY

TOAST CHUTE

CONVEYOR LINK, MODEL T714

CONVEYOR BELT

(TOP VIEW)

SHOWN WITHOUT TOP COVER

REVISED 12/23/96 MJC

PAGE 5




TROUBLESHOOTING GUIDE

A. UNIT WILL NOT HEAT, CONVEYOR WILL NOT TURN.

1. Be sure the main circuit breaker is switched to the ON position.

2. Check to see if the toaster is plugged in and all controls are turned to the

ON

B.

1. Check to see if both top and bottom heat controls have been turned to

HI.

2. Push heat limit switch on front of control box as shown below.

If this reactivates the heater tubes, see HEAT LIMIT SWITCH in

section

C. HEAT LIMIT SWITCH

Your Holman conveyor toaster is equipped with an automatically activated

Heat Limit Switch that interrupts the heater tube connections if the ambient temperature in the control box exceeds 190F (88C). This heat limit switch can be reset manually by pushing the red button on the front of the control box.

HEAT LIMIT SWITCH

CONVEYOR SPEED CONTROL

BOTTOM HEAT CONTROL

TOP HEAT CONTROL

THE HEAT LIMIT SWITCH IS ACTIVATED WHEN THERE IS NOT

SUFFICIENT AIR FLOW GENERATED BY THE COOLING FAN. WHEN

HEAT LIMIT SWITCH HAS BEEN ACTIVATED:

1. DISCONNECT UNIT FROM POWER SOURCE.

2. Check to see if air intake area in the bottom center of the control box cover is free of dust, grease or other obstructions.

Troubleshooting guide continued on page 6

REVISED 1/28/97 MJC




TROUBLESHOOTING GUIDE CONT.

PAGE 6

3. Check if crumb tray is in place. NEVER OPERATE UNIT WITHOUT

CRUMB TRAY IN PLACE AS THIS CAUSES OVERHEATING IN THE

CONTROL

4. If no obstructions to the airflow can be found and if the crumb tray is in place, call Holman Factory Service Department at 1-800-225-3958 for

assistance.


2. Remove right hand side panel (from operator's position). Loosen screws holding drive motor in place and slide motor toward the rear of unit.

Remove drive chain and manually move conveyor belt to check for mechanical binding. If conveyor moves freely, call Holman Factory

Service control may need replacement.

CONTROL KNOBS

SHAFT BEARINGS

RESET BUTTON

CONVEYOR

SPEED CONTROL

DRIVE SHAFT SPROCKET

DRIVE CHAIN

DRIVE MOTOR ADJUSTMENT SLOTS

HEAT CONTROLS

TERMINAL STRIP

RIGHT SIDE SHOWN WITHOUT SIDE PANEL

DRIVE MOTOR

1. Call Holman Factory Service Department at 1-800-225-3958 as speed control should be replaced.

REVISED 7/29/97 MJC

PAGE 7




MAINTENANCE PROCEDURES

A. REPLACING HEATER TUBES (as below)


2. Remove right and left side panels.

3. Remove heater tube wire from terminal block connection, keeping top and bottom wires separate.

4. Remove heater tube retainers by removing retaining screws with washer.

Gently, pull defective heater tube out of unit.

Gently, put new heater tube into unit.

7. Replace heater tube retainers, reconnect heater tube wires to terminal block and install side panels.

HEATER TUBE RETAINER

AIR INTAKE

HEATER TUBE TERMINAL BLOCK (4 POS.)

(2 POS. ON OPOSITE SIDE)

SIDE PANEL

HEATER TUBE RETAINER

HEATER TUBE

Maintenance procedures continued on page 8

REVISED 9/14/94 MJC

PAGE 8




MAINTENANCE PROCEDURES (CONT.)

B. REPLACING FAN MOTOR


2. Remove control box cover with fan motor.

3. Unplug power supply cord from fan motor.

4. Remove(4)screws that hold fan motor and grill to cover.

5. Put replacement motor and grill in place and secure to the control box

cover screws.

6. Reconnect power supply cord to fan motor.

7. Replace control box cover.

CONTROL BOX COVER

AIR INTAKE

FAN MOTOR

SECURED BY 4 SCREWS

AIR INTAKE SCOOP

Maintenance procedures continued on page 9

REVISED 9/14/94 MJC

PAGE 9




MAINTENANCE PROCEDURES (CONT.)

C. REPLACING BELT DRIVE MOTOR


2. Remove right side panel and control box covers.

3. Remove sprocket from motor shaft.

4. Remove the wire from terminal block connecting the drive motor to internal wiring. On units rated 208 or 240 volts, note which color leads are being used for these connections and which lead is capped with white tape. The new motor should use the same arrangement.

5. Remove screws holding motor in place.

6. Put new motor in place and attach loosely with mounting screws.

7. Replace sprocket on motor shaft.

8. Slide motor until the drive chain has about 1/8" slack when lightly pushed at the center of its top open run.

9. Tighten screws to secure motor.

10. Rewire leads same as removed in step 4.

11. Replace side panel and control box cover.

IF ASSISTANCE IS REQUIRED FOR THIS OR ANY OTHER PROCEDURE IN THIS

MANUAL CALL HOLMAN FACTORY SERVICE DEPARTMENT AT 1-800-225-3958, 24

HOURS/DAY 7 DAYS/WEEK.

DRIVE SPROCKET WITH SET SCREW

SHAFT BEARINGS

RIGHT SIDE SHOWN WITHOUT SIDE PANEL

DRIVE SHAFT SPROCKET

DRIVE CHAIN

DRIVE MOTOR ADJUSTMENT SLOTS

(BOTTOM VIEW)

DRIVE MOTOR

DRIVE MOTOR

MOUNTING SCREW

REVISED 9/19/94 MJC




PARTS LIST /EXPLODED VIEW MODEL T710(H), 120, 208, 240 VOLT

28.

3

..

4.

2.

5.

PAGE 10

27.

17.

16.

18.

11.

11.

9.

6.

21.

22.

19.

20.

13.

14.

12.

10.

8.

7.

24.

23.

15.

25.

26.

PART No. QTY

.

1). 400821

2). 197848

2a). 197841

2b). 197844

2c). 197842

3). 400833

4). 160000

5). 400827

5a). 400925

6). 401486

6a). 416789

7). 2P-200662

8). 200643

9). 200645

10). 100900

11). 112261

12). 200519

12a). 200509

13). 200558

DESCRIPTION PART No. QTY. DESCRIPTION

1

4

4

4

4

4

1

1

1

2

2

1

1

1

1

4 Bearings

1

1

Cover, Top

Heater Tube, 120 Volt


Retainer, Heater Tube

Conveyor Belt, T710(H)

Back Panel, Low

Back Panel, High

Side Panel, Low

Side Panel, High (H)

Drive Chain T710(H)

Drive Sprocket

Driven Sprocket

Drive Shaft

Drive Motor, 120 Volt

Drive Motor, 208/240 Volt

13a). 200560

14). 100311

1

1

Fan Motor, 208/240 Volt

Control Box Cover

200652 1 Fan

16). 100901 1 Idler Shaft

100541 1 Crumb

18). 200538 2 Infinite Switch, 208/240 Volt

18a). 200539 2 Infinite Switch, 120 Volt

19). 118000 1

19a). 118042

20). 200566

21). 200702

1

1

2

Speed Control, 120 Volt

Speed control, 208/240 Volt

Reset/High Limit

Knob, Infinite Switch

22). 200703

23). 200551

24). 200712

25). 140025

26). 400825

27). 200753

28). 400891

1

1

4

1

Knob, Speed Cont'l/ Power Saver

Power Saver Switch

Leg, 4" Plastic

Power Supply Cord

1 Toast

1

1

Load up Tray

Heat Shutter (H Model Only)

1 Fan Motor, 120 Volt *29). 115603 4 Security Leg , S710(H) (not shown)

Parts continued on page 11

REVISED 12/6/2005 RMS




PARTS LIST /EXPLODED VIEW MODEL TX710(H) 120, 208, 240 VOLT

1.

3 ..

28.

4.

2.

5.

PAGE 11

17.

16.

18.

29.

11.

9.

6.

21.

22.

19.

20.

13.

14.

12.

25.

10.

8.

7.

27.

23.

15.

24.

26.

PART No. QTY. DESCRIPTION

1). 400821

2). 197848

2a). 197841

2b). 197844

2c). 197842

3). 400833

4). 160003

5). 400827

5a). 400925

6). 401486

6a). 416789

7). 2P-200662

8). 200643

9). 200645

10). 100900

11). 112261

12). 200519

12a). 200509

13). 200558

1

4

4

4

4

4

1

1

1

2

2

1

1

1

1

2

1

1

1

Cover, Top




Conveyor Belt, T710(H)

Back Panel, Low

Back Panel, High

Side Panel, Low


Drive Chain

Drive Sprocket

Driven Sprocket

Drive Shaft

Bearings, Rear

Drive Motor, 120 Volt

Drive Motor, 208/240 Volt 27). 401131

Fan Motor, 120 Volt

PART No. QTY. DESCRIPTION

13a). 200560

14). 100311

1

1


Control Box Cover

200652 1 Fan

16). 100901 1 Idler Shaft

100541 1 Crumb

18). 200538 2 Infinite Switch, 208/240 Volt

18a). 200539 2 Infinite Switch, 120 Volt

19). 118000

19a). 118042

20). 200566

21). 200702

22). 200703

1

1

1

2

1

Speed Control, 120 Volt


Reset/High Limit


Knob, Speed Cont'l/ Power Saver

23). 200551

24). 200712

25). 140025

25a). 140052

26). 400825

28). 400891

1

4

1

1

1

Power Saver Switch

Leg, 4" Plastic

Power Supply Cord, 208/240 Volt

Power Supply Cord, 120 Volt

Toast Chute

1 Extension

1 Heat Shutter (H Model Only)


29). 200693





PARTS LIST /EXPLODED VIEW MODEL T714(H)

28.

PAGE 12

3

..

4.

2.

5.

27.

17.

16.

18.

11.

11.

9.

6.

21.

22.

19.

20.

13.

14.

12.

10.

8.

7.

24.

23.

15.

25.

26.

1). 400847

2). 197850

2a). 197846

2b). 197851

3). 400833

4). 160002

5). 400853

5a). 400926

6). 401486

6a). 416789 1

7). 2P-200663 1

8). 200645

9). 200644

1

1

1

1

1

10). 100902

11). 112261

12). 200509

4

4

4

1

1

4

1

1

1

Top Cover 13). 200560

Heater Tube, 240 Volt 14). 100312


Retainer, Heater Tube 17). 100542

Conveyor Belt 18). 200538

Back Panel, Low

Back Panel, High

Side Panel, Low

19). 118042

20). 200566

21). 200702

Side Panel, High

Drive Chain

Drive Sprocket

Driven Sprocket

Bearings

Drive Motor

22). 200703

23). 200547

24). 200712

25). 140027

26). 400846

27). 200756

28). 400899

*29). 115603


2

1

4

4

1

1

1

1

1

1

4

1

1

1

1

1

2

DESCRIPTION

Fan Motor

Control Box Cover

Idler Shaft

Crumb Tray

Infinite Switch

Speed Control

Reset Switch


Knob, Speed control/Power Saver

Power Saver Switch

Leg, 4" Plastic

Cord/Plug Set

Heat Shutter (H model only)

Security Leg, S714(H) (not shown)





PARTS LIST /EXPLODED VIEW MODEL TX714(H)

1.

PAGE 13

3

..

28.

4.

2.

5.

17.

16.

18.

29.

11.

9.

6.

21.

22.

19.

20.

13.

14.

12.

25.

10.

8.

7.

27.

23.

15.

24.

26.

1). 400847

2). 197850

2a). 197846

2b). 197851

3). 400833

4). 160004

5). 400853

5a). 400926

6). 401486

6a). 416789 1

7). 2P-200663 1

8). 200645

9). 200644

1

1

10). 100902

11). 112261

1

1

1

12). 200509

1

1

1

4

4

4

1

1

4

Top Cover 13). 200560



Retainer, Heater Tube 17). 100508

Conveyor Belt 18). 200538

Back Panel, Low

Back Panel, High

Side Panel, Low

19). 118042

20). 200566

21). 200702

Side Panel, High

Drive Chain

Drive Sprocket

Driven Sprocket

22). 200703

23). 200547

24). 200712

25). 140027

26). 400846

Bearings

Drive Motor 28). 400899

2

1

4

4

1

1

1

1

1

1

1

1

1

2

DESCRIPTION

Fan Motor

Control Box Cover

Idler Shaft

Crumb Tray

Infinite Switch

Speed Control

Reset Switch


Knob, Speed control/Power Saver

Power Saver Switch

Leg, 4" Plastic

Cord/Plug Set

1 Heat Shutter (H model only)






PARTS LIST /EXPLODED VIEW MODEL TX710(H), 208, 240 VOLT

1.

PAGE 14

3

..

28.

4.

2.

5.

17.

16.

18.

29.

11.

9.

6.

21.

22.

19.

20.

13.

14.

12.

25.

10.

8.

7.

27.

23.

15.

24.

26.

PART No. QTY DESCRIPTION

1).

2).

400821

199105

2a). 199106

2)

2a)

3).

4).

5).

6).

209197

209193

401276

160004

400925

416789

4

4

4

1

1

4

4

1

2

Cover, Top

Heater Tube, 208V TX710

Heater Tube, 240V TX710

Heater Tube, 208V TX710H 20). 115146

Heater Tube, 240V TX710H 21). 200702


Conveyor Belt

22).

24).

200703

200712

Back Panel, High


PART No. QTY. DESCRIPTION

17). 100511

18). 200538

19). 118040

1

2

1

Crumb Tray

Infinite Switch, 208/240 Volt


25). 140025

26). 400825

1

2

1

4

1

1

Reset/High Limit


Knob, Speed Cont'l/ Pwr Saver

Leg, 4" Plastic

Power Supply Cord, 208/240 V

Toast Chute

27). 401131 1 Extension

8).

9).

200645

200645

1

2

Drive Sprocket

Driven Sprocket

10). 202900 1 Drive

11). 112261 2 Bearings,

12). 200509

13a). 200560

14). 401462

1

1

1

Drive Motor, 208/240 Volt


Control Box Cover

15). 200562 1 Fan

16). 202904 1 Idler

28). 400891

29). 200693

1

2

Heat Shutter (H Model Only)

Idler Bushing




WIRING DIAGRAM FOR MODEL T710(H & TW) 120 VOLT

TX710(H) 120 VOLT

WIRE DIAGRAM

FOR MODEL T710(H), TX710(H) - 120 VOLT

PAGE 15

PLUG CONFIGURATION

NEMA 5-15P

120 VOLT

REV. 9/15/98 MJC

H:\TOASTERS\T710\

120VAC/WIRDIAG\

T710SCM.DS4

REV. 9/18/98 MJC




WIRING DIAGRAM FOR MODEL T710(H & TW) 208, 240 VOLT

TX710(H) 208, 240 VOLT

T714(H) 208, 240 VOLT (3.2 KW)

PAGE 16

BLUE

220/240

VAC

WHITE

208 VAC

BLACK

COMMON

PLUG CONFIGURATION

NEMA 6-20P

208/240 VOLT

REV. 9/15/98 MJC

H:\TOASTERS\T710\

208VAC\WIRDIAG\

T710SCM.DS4

REV. 9/18/98 MJC




WIRING DIAGRAM FOR MODEL T714(H & TW) TX714, 3.6 kW 208, 240 VOLTS, WIRED

PARELLEL

PLUG CONFIGURATION

NEMA 6-30P

REV. 1/28/97 MJC




WIRING DIAGRAM FOR MODEL B710(H), 120 VOLT

Top Heat

PAGE 18

Control

M

Bottom Heat

Top

Heat

H2

L2

H1

L1

H2

L2

H1 Bottom

Heat

L1

1 2

3 4

L1 L2

GROUND

M

Plug Configuration

NEMA 5-20P

120V

REV. 7/31/97 MJC




WIRING DIAGRAM FOR MODEL S710(H), 120, 208, 240 VOLT

MODEL TX710 WITH OUT POWER SAVER 120, 208, 240 VOLT

PAGE 19

PLUG CONFIGURATION

NEMA 5-15P NEMA 6-20P

120 VOLT 208/240 VOLT

REV. 1/28/97 MJC




WIRING DIAGRAM FOR MODEL S714(H) 208, 240 VOLT

PLUG CONFIGURATION

NEMA 6-30P

REV. 1/28/97 MJC

Star Manufacturing B710H Operation Manual

Top Heat

Bottom Heat

Related manuals

Star Manufacturing

TT960

Holman Cooking/Star Mfg

314HXM

Holman Cooking/Star Mfg

DT14-M

Spice

S710

Star Manufacturing

MM14

Merco / Savory

RT2-AR

Star Manufacturing

EZ10

Holman

EZ10