Operating instructions | Canon 5D Mark III Camcorder User Manual

FEIN Turbo Vac II
9-55-13 / 9-55-13PE
Operating Instructions
MAINTENANCE
After every use:
.
.
.
.
Empty the tank (dirt, dust, and fluids).
Never leave fluids in the tank. This could cause damage to the tank.
After vacuuming fluids, it is necessary to dry extension pieces, tube
and motor parts by running the vacuum a few minutes, after having
emptied the tank.
Always keep a reserve of paper dust bags and filter cartridges, so
that the vacuum is always ready for use.
ATTENTION: READ BEFORE USING
•
•
•
FEIN Power Tools Inc.
1030 Alcon Street
Pittsburgh, PA 15220
(800) 441-9878
•
•
REV. 0 6-15-06
•
Make sure that the voltage nameplate of the device corresponds to the voltage of
your network. The plug has to be protected with a minimum of 15 Amps.
IMPORTANT! THE VACUUM CLEANER IS SUPPLIED FROM THE
FACTORY WITH A SUPPLY CABLE WITH A GROUNDED PLUG . IT
MUST ONLY BE CONNECTED TO AN APPROVED GROUNDED
SOCKET.
Before performing any maintenance work, unplug the vacuum from the outlet.
WARNING! EXPLOSION AND FIRE HAZARD! Never vacuum flammable
fluids or gas, oil, alcohol, solvents, etc. Do not operate near flammable fluids or
gas. Never vacuum warm fluids or materials at more than 140º Fahrenheit
(60º Celsius), such as burning cigarettes, ashes, glowing coals, etc.
WARNING! DO NOT VACUUM HAZARDOUS/CARCINOGENIC DUST
UNLESS THE OPTIONAL HEPA FILTER IS INSTALLED.
Do not pull the vac by the cable and do not damage the insulation on the cable.
If the cable is damaged, it must be replaced immediately.
Always keep the filter cartridge clean so the vacuum cleaner operates properly.
ASSEMBLY INSTRUCTIONS
To attach the wheels, press the wheel posts
into the four holes provided.
a) Connect the vacuum end of hose 2 to
the receptacle Q by pressing in. In order to
remove the hose, press button L on receptacle and pull the hose out simultaneously.
b) Connect the handle 4 with the hose end 3
by pressing in. The handle is provided with a
suction force reducing device. Turn in the
direction of the arrow. In order to get full
suction pressure, keep the regulating device
closed.
9-55-13 / 9-55-13PE TURBO II VAC ACCESSORIES
Item Part Number
Description
1
919036B94
Extension tube-chrome
2
3
921067A13
921069A13
Handle
Adaptor
4
5
921072K13
919001A13
Step adaptor
Brush
6
7
919003K13
919007K13
Upholstery nozzle
Crevice tool
8
9
921051A13
921056000
Wet brush
Rubber strip
10
11
919064B13
919043R14
Floor brush with rollers
Thread pick for brush
12
13
90204200
TII1MCRN
Anti-foam filter
1Micron filter
14
TIIHEPA
TII3002
Hepa filter 0.3 microns
Flange filter
15
16
TII3001
913064AGA6
Turn screw-filter
Cloth filter
17
18
913036K01
921086AA13
Paper dust bag- 3 pack
Y connector with cap
19
20
921087AK13
3916054A089
Y cap
Hose cradle
21
526300AA13
Basket and strap
Kits: FBK
consists
of 1 each
c) Tube extension pieces 5 and accessories
can be connected by pressure. For disassembling, slightly turn both parts and draw apart.
d) To use the optional combination attachment
1 for hard floors in PVC, linoleum, stone,
etc. press the switch button with your foot, so
that the bristles emerge d1. For carpets, the
bristles have to be retracted d2 .
1
TIIMCRN 1 Micron pleated filter
913036A01 Paper dust bag
TII3002 Filter flange
TII3001 Flange turn screw
FBK-HEPA
consists
of 1 each
TIIHEPA Hepa pleated filter
913049A01 Hepa dust bag
TII3002 Filter flange
TII3001 Flange turn screw
DW1
consists
of 1 each
(2) 919036B94 Extension tube
921067A13 Handle
919007K13 Crevice tool
902042000 Anti-foam filter
919001A13 Brush
921051A13 Wet floor brush
919003K13 Upholstery Nozzle
919064B13 Floor brush
6
SUCTION OF DRY DUST AND DIRT (continued)
ATTENTION: If suction pressure decreases, replace
the paper dust bag H with a new one. From time to
time the filter cartridge G should be cleaned with a
soft brush, ensuring longer life and higher performance.
SUCTION OF FLUIDS
a) First, remove any dirt and dust residue from
previous cleaning operations from the container.
Remove the cloth filter or the cartridge filter G and
replace it with the anti-foam filter R . DO NOT USE
THE CLOTH FILTER, THE CARTRIDGE FILTER
OR THE PAPER DUST BAG DURING THE
SUCTION OF FLUIDS.
b) In order to guarantee enough air flow, it is recommended that accessories not be completely immersed
into the fluids.
c) When the fluids have reached the highest permitted
level in the tank, the float regulator F automatically
blocks suction and the motor gets noisier. Switch the
vacuum off IMMEDIATELY, pull out the plug,
remove the suction head from the tank and empty the
tank.
SUCTION OF DRY DUST AND DIRT
The cloth filter that came with your FEIN Turbo II will contain extracted dust 5.0
microns in size and larger. If picking up fine dust, you will need to use a pleated filter
cartridge and paper bag, which can be purchased as a (FBK) kit or a (FBK-HEPA)
kit for hazardous dust vacuuming. (see page 6 for kit contents).
a) To install the optional filter cartridge G place the
turn screw I inside the flange K . Place the filter
cartridge on the float cage then put the flange assembly on the bottom of the filter. Turn the screw quarter
turn to lock the filter on.
b) In order to remove the filter cartridge turn the
screw I quarter turn counterclockwise and pull out
the filter cartridge.
Do not use vacuum without a filter. Use the cloth
filter that came with your vacuum, or a pleated
filter. Do not use both at the same time. Failure to
use a filter when dry vacuum cleaning will damage
the motor. NEVER USE VACUUM CLEANER
WITH A WET FILTER CARTRIDGE FOR DRY
VACUUM CLEANING. It quickly becomes clogged
and unusable.
c) Fix the optional paper dust bag H to the inner
side of the tube-connection in the receptacle: fig.c.
and d. When using this paper dust bag the dirt can
be removed more hygienically and the life of the filter
cartridge will be increased. The paper dust bag H
should be used with the filter cartridge; it should
NEVER be used by itself or with the cloth filter.
(continue on page 5)
5
2
3
9-55-13 / 9-55-13PE TURBO II VAC
ITEM # DESCRIPTION
PART NUMBER
11
POWER CORD SET
3-07-05-065-99-9
12
SCREW
901A11A89
13
CABLE CLAMP
101035K00
16
SCREW
901A19A89
17
WASHER
901D07AG87
18
TERMINAL BLOCK
905217000
35
SCREW
901A16A89
42
CABLE
905391000
44
BUNGEE
920056000
53
FACE PLATE
521006K13
57
RECEPTACLE COVER
905278K15
73
AUTO START SWITCH
905331R00
AUTO START SWITCH (9-55-13PE) 905490A000
107
SWITCH (ON/OFF)
905306000
111
RECEPTACLE
905398K13
112
SWITCH (MANUAL / AUTO)(WIDE) 905307A000
200
TOP HANDLE
521049AK50
201
COVER WITH HANDLE
521049B50
202
COVER GASKET
920021B00
203
COVER SOUNDPROOFING
902033000
205
COVER BAFFLE
521002K13
206
SIDE SOUNDPROOFING
902048000
209
MOTOR GASKET - 110 VOLT
920042000
210
CHAMBER MOTOR GASKET
920039000
211
MOTOR SOUNDPROOFING
902043000
212
MOTOR - 110 VOLT
918M5602U
213
CARBON BRUSHES (2)
905317G02
216
MOTOR SOUNDPROOFING
902036000
217
MOTOR COVER
521003K13
218
MOTOR FILTER
902032A00
219
GASKET - 110 VOLT
920038000
220
FLOAT
521010K00
222
FLOAT CAGE
521007K13
255
PLUG
920060000
280
PLUG
920065000
286
CONTAINER
521052K50
287
BUMPER
524301B15
412
LOCK LEVER
525002089
420
SWIVEL WHEELS
521047K41
427
HOSE RECEPTACLE
521016A13
445
CLOTH FILTER
913064AGA6
500
16' HOSE
921049GN1
16' HOSE (9-55-13PE)
921159AK30
501
SLEEVE - VACUUM END
921047K13
502
SLEEVE - TOOL END
921048K13
504
CONNECTOR RING
919067K13
505
RING - HOSE
919066A13
710
PNEUMATIC VALVE (9-55-13PE)
918V01A001
4
SUCTION OF DRY DUST AND DIRT (continued)
ATTENTION: If suction pressure decreases, replace
the paper dust bag H with a new one. From time to
time the filter cartridge G should be cleaned with a
soft brush, ensuring longer life and higher performance.
SUCTION OF FLUIDS
a) First, remove any dirt and dust residue from
previous cleaning operations from the container.
Remove the cloth filter or the cartridge filter G and
replace it with the anti-foam filter R . DO NOT USE
THE CLOTH FILTER, THE CARTRIDGE FILTER
OR THE PAPER DUST BAG DURING THE
SUCTION OF FLUIDS.
b) In order to guarantee enough air flow, it is recommended that accessories not be completely immersed
into the fluids.
c) When the fluids have reached the highest permitted
level in the tank, the float regulator F automatically
blocks suction and the motor gets noisier. Switch the
vacuum off IMMEDIATELY, pull out the plug,
remove the suction head from the tank and empty the
tank.
SUCTION OF DRY DUST AND DIRT
The cloth filter that came with your FEIN Turbo II will contain extracted dust 5.0
microns in size and larger. If picking up fine dust, you will need to use a pleated filter
cartridge and paper bag, which can be purchased as a (FBK) kit or a (FBK-HEPA)
kit for hazardous dust vacuuming. (see page 6 for kit contents).
a) To install the optional filter cartridge G place the
turn screw I inside the flange K . Place the filter
cartridge on the float cage then put the flange assembly on the bottom of the filter. Turn the screw quarter
turn to lock the filter on.
b) In order to remove the filter cartridge turn the
screw I quarter turn counterclockwise and pull out
the filter cartridge.
Do not use vacuum without a filter. Use the cloth
filter that came with your vacuum, or a pleated
filter. Do not use both at the same time. Failure to
use a filter when dry vacuum cleaning will damage
the motor. NEVER USE VACUUM CLEANER
WITH A WET FILTER CARTRIDGE FOR DRY
VACUUM CLEANING. It quickly becomes clogged
and unusable.
c) Fix the optional paper dust bag H to the inner
side of the tube-connection in the receptacle: fig.c.
and d. When using this paper dust bag the dirt can
be removed more hygienically and the life of the filter
cartridge will be increased. The paper dust bag H
should be used with the filter cartridge; it should
NEVER be used by itself or with the cloth filter.
(continue on page 5)
5
2
ASSEMBLY INSTRUCTIONS
To attach the wheels, press the wheel posts
into the four holes provided.
a) Connect the vacuum end of hose 2 to
the receptacle Q by pressing in. In order to
remove the hose, press button L on receptacle and pull the hose out simultaneously.
b) Connect the handle 4 with the hose end 3
by pressing in. The handle is provided with a
suction force reducing device. Turn in the
direction of the arrow. In order to get full
suction pressure, keep the regulating device
closed.
9-55-13 / 9-55-13PE TURBO II VAC ACCESSORIES
Item Part Number
Description
1
919036B94
Extension tube-chrome
2
3
921067A13
921069A13
Handle
Adaptor
4
5
921072K13
919001A13
Step adaptor
Brush
6
7
919003K13
919007K13
Upholstery nozzle
Crevice tool
8
9
921051A13
921056000
Wet brush
Rubber strip
10
11
919064B13
919043R14
Floor brush with rollers
Thread pick for brush
12
13
90204200
TII1MCRN
Anti-foam filter
1Micron filter
14
TIIHEPA
TII3002
Hepa filter 0.3 microns
Flange filter
15
16
TII3001
913064AGA6
Turn screw-filter
Cloth filter
17
18
913036K01
921086AA13
Paper dust bag- 3 pack
Y connector with cap
19
20
921087AK13
3916054A089
Y cap
Hose cradle
21
526300AA13
Basket and strap
Kits: FBK
consists
of 1 each
c) Tube extension pieces 5 and accessories
can be connected by pressure. For disassembling, slightly turn both parts and draw apart.
d) To use the optional combination attachment
1 for hard floors in PVC, linoleum, stone,
etc. press the switch button with your foot, so
that the bristles emerge d1. For carpets, the
bristles have to be retracted d2 .
1
TIIMCRN 1 Micron pleated filter
913036A01 Paper dust bag
TII3002 Filter flange
TII3001 Flange turn screw
FBK-HEPA
consists
of 1 each
TIIHEPA Hepa pleated filter
913049A01 Hepa dust bag
TII3002 Filter flange
TII3001 Flange turn screw
DW1
consists
of 1 each
(2) 919036B94 Extension tube
921067A13 Handle
919007K13 Crevice tool
902042000 Anti-foam filter
919001A13 Brush
921051A13 Wet floor brush
919003K13 Upholstery Nozzle
919064B13 Floor brush
6
FEIN Turbo Vac II
9-55-13 / 9-55-13PE
Operating Instructions
MAINTENANCE
After every use:
.
.
.
.
Empty the tank (dirt, dust, and fluids).
Never leave fluids in the tank. This could cause damage to the tank.
After vacuuming fluids, it is necessary to dry extension pieces, tube
and motor parts by running the vacuum a few minutes, after having
emptied the tank.
Always keep a reserve of paper dust bags and filter cartridges, so
that the vacuum is always ready for use.
ATTENTION: READ BEFORE USING
•
•
•
FEIN Power Tools Inc.
1030 Alcon Street
Pittsburgh, PA 15220
(800) 441-9878
•
•
REV. 0 6-15-06
•
Make sure that the voltage nameplate of the device corresponds to the voltage of
your network. The plug has to be protected with a minimum of 15 Amps.
IMPORTANT! THE VACUUM CLEANER IS SUPPLIED FROM THE
FACTORY WITH A SUPPLY CABLE WITH A GROUNDED PLUG . IT
MUST ONLY BE CONNECTED TO AN APPROVED GROUNDED
SOCKET.
Before performing any maintenance work, unplug the vacuum from the outlet.
WARNING! EXPLOSION AND FIRE HAZARD! Never vacuum flammable
fluids or gas, oil, alcohol, solvents, etc. Do not operate near flammable fluids or
gas. Never vacuum warm fluids or materials at more than 140º Fahrenheit
(60º Celsius), such as burning cigarettes, ashes, glowing coals, etc.
WARNING! DO NOT VACUUM HAZARDOUS/CARCINOGENIC DUST
UNLESS THE OPTIONAL HEPA FILTER IS INSTALLED.
Do not pull the vac by the cable and do not damage the insulation on the cable.
If the cable is damaged, it must be replaced immediately.
Always keep the filter cartridge clean so the vacuum cleaner operates properly.
Download PDF

advertising