SPLIT LID TABLE TOP TWO SIDED TOASTER MODEL GR14SPT SERIES

®
®
SPLIT LID TABLE TOP
TWO SIDED TOASTER
MODEL
GR14SPT SERIES
Installation and
Operation
Instructions
®
®
2M-Z3391 Rev. K 8/01/12
GR14SPT-120V
9D-GR14SPT-120V
9D-GR14SPT-CUL
SAFETY SYMBOL
These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTICE
Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.
Star reserves the right to change specifications and product design without
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.
Due to periodic changes in designs, methods, procedures, policies and
regulations, the specifications contained in this sheet are subject to change
without notice. While Star International Holdings Inc., Company exercises
good faith efforts to provide information that is accurate, we are not
responsible for errors or omissions in information provided or conclusions
reached as a result of using the specifications. By using the information
provided, the user assumes all risks in connection with such use.
MAINTENANCE AND REPAIRS
Contact your local authorized service agent for service or required maintenance.
Please record the model number, serial number, voltage and purchase date in the area below and have it ready when
you call to ensure a faster service.
Model No.
Authorized Service Agent Listing
Reference the listing provided with the unit
Serial No.
Voltage
Purchase Date
or
for an updated listing go to:
Website:
E-mail www.star-mfg.com
[email protected]
Service Help Desk
Business
Hours:
8:00 am to 4:30 p.m. Central Standard Time
Telephone:
(314) 678-6303
Fax:
(314) 781-2714
E-mail
[email protected]
[email protected]
[email protected]
Website:
www.star-mfg.com
Mailing Address:
Star International Holdings Inc., Company
10 Sunnen Drive
St. Louis, MO 63143
U.S.A
2
GENERAL INSTALLATION DATA
CAUTION
This equipment is designed and sold for commercial use only by personnel trained and experienced
in its operation and is not sold for consumer use in and around the home nor for use directly by the
general public in food service locations.
Before using your new equipment, read and understand all the instructions & labels associated with
the unit prior to putting it into operation. Make sure all people associated with its use understand the
units operation & safety before they use the unit.
All shipping containers should be checked for freight damage both visible and concealed. This
unit has been tested and carefully packaged to insure delivery of your unit in perfect condition. If
equipment is received in damaged condition, either apparent or concealed, a claim must be made
with the delivering carrier.
Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a
request for inspection of concealed damage must be made with carrier within 15 days. Be certain to
retain all contents plus external and internal packaging materials for inspection. The carrier will make
an inspection and will supply necessary claim forms.
INSTALLATION
1. Plug unit into dedicated 120V AC line with 20AMP receptacle, CUL models, 30AMP.
2. DO NOT plug a 120V unit into 220V line. Doing so will damage the unit and void the
warranty.
3. Each machine has been properly wired and inspected at the factory for operation on the
voltage and type of current specified on the nameplate.
DO NOT CONNECT TO ANY OTHER TYPE OF CURRENT OR THE MACHINE WILL
WARNING BE SERIOUSLY DAMAGED.
4. DO NOT operate without top burn guard in place.
INITIAL START UP
Before using the unit for the first time, clean and heat for approximately 45 minutes. Refer to your
corporate operating procedures for seasoning your grill.
OPERATING INSTRUCTIONS
Make sure unit is plugged into 20AMP/30AMP receptacle (depending on model) and is on a
dedicated line specified on the units name plate.
1. Turn unit on by placing switch in "ON" position. The "Heat On" indicator, program number
and display will flash indicating unit is heating. When the preset temperature is reached, the
heating light, display and program light indicator will stop flashing followed by 3 beeps.
(Initial start-up heating time is approximately 30 minutes.)
2. Place product on the bottom cooking surface of the unit and close the lids.
3. Press program button and let displayed time count down to "0" at which time unit will beep.
To turn off the beeper, press program button again.
4. Raise lid until it engages into first detent and remove food. Using spatula, scrape residue into
the grease catcher cup.
NOTE: Metal utensils may be used, however, using nonmetal utensils will prolong the
life of the cooking surface.
5. Turn the unit off when not in use.
DO NOT ADJUST TIME AND TEMPERATURE
The unit time and temperature is preset by the factory to the specific customer requirements for
flatbread, burritos, quesadillas and cleaning. If adjustments are required for additional food products,
please refer to the time or temperature programming section on page 4.
TEMPERATURE/TIMER CONTROLLER OPERATION SPECIFICATIONS
Start-up:
1. The preset time will flash until the preset temperature is reached.
2. When the control reaches the preset temperature, time display, "Heat On" indicator and program
indicator will stop flashing and the alarm will beep three times.
Temperature:
1. To view the actual temperature, press and hold "Temp Button." Display will read "Lo F" if
temperature is below 273°F and "Hi F" if temperature is above 573°F.
To Program Time and Temperature:
1. Press and hold "Temp" (actual temperature displays).
2. While holding "TEMP," press and hold any program button on the Left PC board for 1 second,
the LED above program lights and display reads "_ _ _ _." Enter the four - digit security code
sequence: 4, 3, 2, 1. Starting with the first digit, the center horizontal bar will light on each digit
as the security code is entered. The security code will not show on display. Once the correct
sequence has been entered, the preset time will be displayed and the LED for that program will
begin to flash.
3. Set the time with the + or - buttons.
4. Press the "TEMP" button to save the time.
5. The preset temperature will now be displayed.
6. Set the desired temperature for this program using the + or - buttons.
7. Press the "TEMP" button to save temperature and to exit programming mode for this
program. The LED will stop to flash but will remain lit.
8. To stay in program mode without re-entering the security code, press and hold the "TEMP"
button and press the program button that you want to program. The programmed time
for that button will display. Release the "TEMP" button and that program button. Repeat
steps 3 through 8 until programming is finished.
9. While programming a program (LED is flashing), if no input is received for 15 seconds,
the unit will revert to normal operation and the security code must be re-entered.
NOTE: Temperature settings are done with the Left PC board only. The time settings
programmed on the Left PC board will also be programmed onto the Right PC board. See
next column to make changes to the Right PC board only. Each programming change
must be saved by pressing the "TEMP" button!Right PC board (Timer only):
1. To Change the time on Right PC board, press and hold the "TEMP" button on the Left PC
board and press and hold any program button on the Right PC board for one second.
The LED above the program button will light and the Right Display will read "_ _ _ _."
Enter the four-digit security code sequence, 4, 3, 2, 1. Starting with the first digit, the center
horizontal bar will light on each digit as the security code is entered. The security code will not
show on display. Once the correct sequence has been entered, the preset time will be displayed
and the LED for that program will begin to flash.
2. Set the time with the "+ or -" buttons.
3. Press the "TEMP" button to save the time.
4. The LED will stop to flash but will remain lit.
5. To stay in program mode without re-entering the security code, press and hold the "TEMP"
button and press the program button that you want to program. The programmed time
for that button will display. Release the "TEMP" button and that program button. Repeat
steps 3 through 8 until programming is finished.
6. While programming a program (LED is flashing), if no input is received for 15 seconds,
the unit will revert to normal operation and the security code must be re-entered.
Operation:
1. Press any program button (1-4) on either side to begin the timer countdown for that side. The
LED for the appropriate program will be lit during the countdown and the remaining time will be
displayed. The countdown may be stopped at any time by pressing the same program button.
The display will return to the programmed time of that button.
2. When the display reaches "00:00," the buzzer will sound and the digits will flash.
3. Press the program button to silence the buzzer and return the readout to programmed time.
4. The Right and Left boards will operate independent of each other. Both timers can be in operation
at the same time. The "00:00" display will show which side is timed out.
MONTHLY INSPECTION
Check all bolts/screws and tighten if necessary.
CLEANING
DAILY CLEANING PROCEDURES
Begin toaster cleaning procedure by using operating procedures within your organization, or follow the
steps below:
1. Scrape griddle with a spatula to remove loose food debris.
2. Turn grill to 275°F by pressing button #4 (programmed for cleaning mode).
3. Once grill reaches cleaning temperature, turn the grill off and unplug it.
4. Pour 1/4 cup of grill cleaner onto the bottom cooking surface of hot grill. (Grill cleaning fluid
may be purchased from local distributor.)
5. Immediately spread grill cleaner around the grill with a cleaning pad. Use moderate pressure
to scrape away burnt-on food.
6. Apply grill cleaner to a cleaning pad.
7. Use moderate pressure to scrape away burnt-on food on top cooking surfaces.
8. Drain grill cleaner to grease trap.
9. Wipe off remaining grill cleaner with a thick damp cloth until clean.
10. Empty and clean the grease catcher cup as required using detergent and water after
removing cup from unit.
CARBON BUILDUP: A black matter that forms on or near the cooking surface. Generally this
is a combination of: releasing agents, oils, food particles etc. that has cooked itself to the
surface. After a period of time without cleaning, this will reduce performance and material
may start flaking off. When that happens, follow the "Carbon Cleaning" procedures.
CARBON CLEANING
When carbon build up occurs, use a carbon removal agent according to the instructions provided with
the cleaner. When this process is complete, you must re-season the grill according to your company/
corporate guidelines, or the seasoning instructions in this manual.
DO NOT IMMERSE OR LET THE UNIT STAND IN WATER.
DO NOT HOSE DOWN.
CAUTION KEEP AWAY FROM RUNNING WATER.
To remove burned on grease or food residue use the following mixture:
1 Tablespoon liquid dish detergent
1 Cup of warm water
CAUTION
DO NOT SPLASH CONTROL HOUSING!
Do not splash conduit connecting top and bottom of the toaster!!
MAINTENANCE AND REPAIRS
Contact your local authorized service agent for service or required maintenance. Refer to the authorized
service center listing provided with the unit.
18
UNITS WITH IEC CONNECTOR:
L
POWER INLET CONNECTOR:
IEC 320 C-20 POWER INLET, ON ALL 208 - 240V UNITS.
FOR USE WITH DETACHABLE CORDSETS SUPPLIED
WITH A STRAIGHT, FEMALE, IEC 60320 C-19 CONNECTOR.
N
19
G
20
TOP ELEMENT
LEFT
(ELEMENT MAS ALTO)
TOP ELEMENT
RIGHT
(ELEMENT MAS ALTO)
SENSOR - RIGHT
(SENSORIO)
SENSOR - LEFT
(SENSORIO)
TRANSFORMER
(TRANSFORMADOR)
TERMINAL BLOCK
(BLOQUE TERMINAL)
RELAY
(RELE)
8
7
8
7
4
4
B A
D C
14
2
5
1
10
9
15
3
6 2
8 4
1
0
6 2
8 4
1
0
16
12
11
6
13
12
11
10
9
BOTTOM ELEMENT
(ELEMENTO MAS BAJO)
SWITCH
(INTERRUPTOR)
5
6
13
16
15
E11
E12
E4
E1
3
14
1
2
E3
E2
E7
E6 E5
REAR OF CONTROLLER
FOR REFERENCE
WIRING DIAGRAM IS SHOWN AS UNIT IS ASSEMBLED
WITH THE BOTTOM PLATE REMOVED. THE TOP
DESCRIPTIONS ARE THEIR POSITIONS WHEN UPRIGHT.
WIRE DIAGRAM, 230V, 2300 WATT
(2J-Z6323 CONTROLLER ONLY)
MODEL: GR14SPTA-UK
STAR MANUFACTURING INTERNATIONAL INC.
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.
SK2017
NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
Rev C
06/30/2011
59
62
61
12
30
59
48
13
61
36
4
56
57
58
44
54
59
57
9
38
8
5
51
40
46
37
50
10
34
20
54
33
28
52
41
52
55 56
35
3
47
24
53
14
49
19
32
60
23
1
15
TEM
P HEAT
ON
TIME
/ TEM
ON
OFF
FLAT
BREA
D
25
P
1
TIME
2
/ TEM
P
3
QUES
4
CLEAN
1
FLAT
BREA
D
2
3
QUES
4
6
43
39
51
42
7
27
45
16
21
11
Nameplate
18
45
26
17
SOME ITEMS ARE INCLUDED FOR
ILLUSTRATIVE PURPOSES ONLY AND IN
CERTAIN INSTANCES MAY NOT BE AVAILABLE
MODEL - GR14SPT
STAR MANUFACTURING INTERNATIONAL, INC.
SK1750
REV. I
8/1/13
2M-Z3391, SPLIT LID TABLE TOP TWO SIDED TOASTER
22
PARTS LIST
January 16, 2013, Rev. J
GR14SPT-120V, CUL, CE SPLIT LIDD TABLE TOP TOASTER PARTS LIST
Fig. No
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2M-Z3391, SPLIT LID TABLE TOP TWO SIDED TOASTER
17
18
19
20
21
22
23
24
25
26
27
28
30
32
33
34
35
36
37
38
Part No
2A-Z6484
D9-GR0152
D9-GR0177
D9-GR0176
D9-GR0156
D9-GR0518
D9-GR0182
2A-Y6142
2A-Z11501
2B-Z3336
2C-Z3200
2C-Z3350
2E-Z3808
2E-05-07-0350
2E-05-07-0351
2E-Y9251
2E-Z4119
2E-Z4304
2E-Z2894
D9-Z3903
2E-Z3278
2E-Z3335
PS-GR0361
PS-GR0356
2I-05-07-0013
2J-Z3263
2J-Z6323
D9-GR0529
2K-Y6764
2K-Z1971
2M-12-07-0038
2M-Z2620
2M-Z3337
2N-Z9324
2N-Z9327
PS-Z9325
PS-Z9326
2R-Z3345
2V-Z3152
2V-Z3252
B9-04-WB-0046
Qty
2
1
1
1
1
1
2
4
4
4
4
2
1
1
1
1
2
2
2
1
2
1
1
1
14
1
2
1
1
2
1
2
2
2
Description
PLATE (COUNTER BALANCE MOUNT)
BODY ASSEMBLY
BURN GUARD ASSEMBLY - LEFT
BURN GUARD ASSEMBLY - RIGHT
REAR PLATE ASSEMBLY
GREASE DRAWER ASSEMBLY
TOP RETAINING PLATE ASSEMBLY
PART OF ITEM #34
SLEEVE HANDLE
FOOT 1” SOLID RUBBER
14” ARM
PIN - TOP HOUSING
HALF CLAMP - .188 DIA.
SWITCH TOGGLE
TRANSFORMER 230V/10A 6VA
TRANSFORMER 115/10V 6VA
CORD SET CONT EUR 16AMP
CORD POWER 5-20P
CORD POWER 5-30P
TERMINAL BLOCK (304)
BRACKET, PROBE MOUNT
RTD PROBE - 48” LONG WIRE
RELAY DOUBLE POLE-SINGLE THROW
KIT, 2F-Z1945 CASTING - SMOOTH BOTTOM, ALUMINUM
KIT, 2F-Z3237 CASTING - TOP
BOOT SWITCH
GR14SPT-CE
GR14SPT-CE
120V
CUL
TIME/TEMPERATURE CONTROL, °F
TIME/TEMPERATURE CONTROL °F/°C
TIME/TEMPERATURE CONTROL F/C PROGRAMMED
BUSHING 90 SR 17-2
SPACER
LABEL - ON & OFF
LABEL - CAUTION, BI-LINGUAL
OVERLAY
ELEMENT, HEATING, 1300W@120V, 11.07OHMS, 10 AMPS
ELEMENT 1300WATT 240V-14B
ELEMENT, HEATING, TOP 500W
ELEMENT, 500 WATT 240V SPT, TOP
COUNTER BALANCE - SPLIT TOP
HANDLE
TOP HOUSING LATCH ROD
CLAMP WIRE SUPPORT
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED
INCLUDE MODEL AND SERIAL NUMBER
Application
GR14SPT-120V, 240V, CUL,
GR14STB-120V, 240V,
GR14STE-120V
GR14SPT-CE, GR14SPTK-TAI
120V, CUL
GR14SPT-CE
120V, CUL
GR14SPT-CE
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing
International, Inc.
PAGE
OF
1
2
PARTS LIST
January 16, 2013, Rev. J
GR14SPT-120V, CUL, CE SPLIT LIDD TABLE TOP TOASTER PARTS LIST
45
46
47
48
49
50
51
52
NI
53
54
55
56
57
58
59
60
61
62
Part No
D9-GR0151
D9-Z2133
D9-Z2618
D9-Z2619
D9-Z2888
D9-GR0181
D9-GR0520
D9-GR0526
D9-Z3902
Z1-70-07-0343
D9-GR0189
D9-GR0183
D9-Z3826
2A-Z6604
2C-08-07-0285
2E-Y9253
2E-Z3768
2E-Z2898
2C-1516
2C-Z3780
2C-Z3917
2A-Z3827
2C-40637
PS-GR134
2C-Z2992
2C-08-07-0262
Qty
1
2
1
1
1
2
Description
FACEPLATE ASSEMBLY
INSULATION FIBERGLAS TOP
BTM ELEMENT RET. PLATE
BTM INSULATION RET. PLATE
INSULATION - 14”
TOP HOUSING AND CONDUIT ASSEMBLY
BASE ASSY / GREASE CABINET
1
BASE BTM / GRS CAB / IEC ASSY
2 PLATE - TOP ELEMENT RET.
1 SWITCH GUARD
2 TOP BURN GUARD ASSEMBLY
1 INSULATION BAFFLE ASSEMBLY
1 INSULATION - BAFFLE
12 SPACER - INSULATION PLATE
12 SCREW 10-24X3/4X3/8 TYPE 2 HEX DBL END STL
1 INLET IEC 320 16 AMP
2 LOCKNUT, CONDUIT 1/2”
2 CONDUIT ASSY
4 SCREW 10-24 X 1” STL RH NP, LATCH ROD
4 RETAINER, CONDUIT
4 RIVIT, POP
2 PLATE, STAMPING CONDUIT
12 ACORN NUT, 1/4-20 CAP MS
AR KIT, BEARING ASSY, COUNTER BALANCE
12 BOLT 1/4-20X1 PHP STL NP
8 WASHER 1/4-20X1 INT STL NP
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED
INCLUDE MODEL AND SERIAL NUMBER
Application
GR14SPT-CE
GR14SPT-CE
2M-Z3391, SPLIT LID TABLE TOP TWO SIDED TOASTER
Fig. No
39
40
41
42
43
44
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
10
PAGE
OF
2
2
Visit our Website at: www.star-mfg.com
Email: [email protected]
THOROUGHLY INSPECT YOUR UNIT ON ARRIVAL
This unit has been tested for proper operation before leaving our plant to insure delivery of your unit in perfect condition. However, there are instances in which
the unit may be damaged in transit. In the event you discover any type of damage to your product upon receipt, you must immediately contact the transportation
company who delivered the item to you and initiate your claim with same. If this procedure is not followed, it may affect the warranty status of the unit.
LIMITED EQUIPMENT WARRANTY
All workmanship and material in Star products have a one (1) year limited warranty on parts & labor in the United States and Canada. Such warranty is limited
to the original purchaser only and shall be effective from the date the equipment is placed in service. Star's obligation under this warranty is limited to the repair
of defects without charge, by the factory authorized service agency or one of its sub-agencies. Models that are considered portable (see below) should be taken
to the closest Star service agency, transportation prepaid.
> Star will not assume any responsibility for loss of revenue.
> On all shipments outside the United States and Canada, see International Warranty.
* The warranty period for the Ultra-Max, Hot Plates, Griddles, Charbroilers is (3) years parts & labor.
* The warranty period for the Star-Max, Charbroilers, Griddles, Hot Plates, Fryers & Finishing Oven is (2) years parts & labor.
* The warranty period for the JetStar six (6) ounce & Super JetStar eight (8) ounce series popcorn machines is two (2) years.
* ThewarrantyperiodfortheChrome-MaxGriddlesisfive(5)yearsonthegriddlesurface.Seedetailedwarrantyprovidedwithunit.
* ThewarrantyperiodforTeflon/Dura-Teccoatingsisoneyearundernormaluseandreasonablecare.Thiswarrantydoesnotapplyifdamageoccursto
Teflon/Dura-Teccoatingsfromimpropercleaning,maintenance,useofmetallicutensils,orabrasivecleaners,abrasivepads,productidentifiersand
point-of-sale attachments, or any other non-food object tha comes in continuous contact with the roller coating. This warranty does not apply to the
“non-stick” properties of such materials.
> This warranty does not apply to "Special Products" but to regular catalog items only. Star's warranty on "Special Products" is six (6) months on parts
and ninety (90) days on labor.
> This warranty does not apply to any item that is disassembled or tampered with for any purpose other than repair by a Star Authorized Service Center or
the Service Center's sub-agency.
> This warranty does not apply if damage occurs from improper installation, misuse, wrong voltage, wrong gas or operated contrary to the Installation and
Operating instructions.
> This warranty is not valid on Conveyor Ovens unlessa"start-up/check-out"hasbeenperformedbyaFactoryAuthorizedTechnician.
PARTS WARRANTY
Parts that are sold to repair out of warranty equipment are warranted for ninety (90) days. The part only is warranted, the labor to replace the part is NOT warranted.
SERVICES NOT COVERED BY WARRANTY
1. Traveltimeandmileagerenderedbeyondthe50mileradiuslimit
10. Voltage conversions
2. Mileage and travel time on portable equipment (see below)
11. Gas conversions
3. Labor to replace such items that can be replaced easily during a daily cleaning
12. Pilot light adjustment
routine, ie; removable kettles on fryers, knobs, grease drawers on griddles, etc.
13. Miscellaneous adjustments
4. Installation of equipment
14. Thermostat calibration and by-pass adjustment
5. Damagesduetoimproperinstallation
15. Resettingofcircuitbreakersorsafetycontrolsorresetbuttons
6. Damages from abuse or misuse
16. Replacementofbulbs
7. Operated contrary to the Operating and Installation Instructions
17. Replacementoffuses
8. Cleaning of equipment
18. Repairofdamagecreatedduringtransit,delivery,&
9. Seasoning of griddle plates
installationORcreatedbyactsofGod
PORTABLE EQUIPMENT
Star will not honor service bills that include travel time and mileage charges for servicing any products considered "Portable" including items listed below.
These products should be taken to the Service Agency for repair:
ALL:
* TheModel510FD,510FFFryer.
* Pop-Up Toasters
* TheModel526TOAToasterOven.
* Butter Dispensers
* TheModelJ4R,4oz.PopcornMachine.
* Pretzel Merchandisers
*TheModel518CMA&526CMACheeseMelter.
* TheModel12MC&15MC&18MCPHotFoodMerchandisers.
* TheModel12NCPW&15NCPWNachoChip/PopcornWarmer.
* All Hot Dog Equipment except Roller Grills & Drawer Bun Warmers.
* All Nacho Cheese Warmers except Model 11WLA Series Nacho Cheese Warmer.
* All Condiment Dispensers except the Model HPD & SPD Series Dispenser.
* All Specialty Food Warmers except Model 130R, 11RW Series, and 11WSA Series.
* AllQCS/RCSSeriesToastersexcept Model QCS3 & RCS3 Series.
* All Fast Steamer Models except Direct Connect Series.
(Model 16PD-A Only)
* Pastry Display Cabinets
* Nacho Chip Merchandisers
* Accessories of any kind
* Sneeze Guards
* Pizza Ovens
(Model PO12 Only)
* Heat Lamps
* Pumps-Manual
The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty.
FOR ASSISTANCE
Should you need any assistance regarding the Operation or Maintenance of any Star equipment; write, phone, fax or email our Service Department.
In all correspondence mention the Model number and the Serial number of your unit, and the voltage or type of gas you are using.
11
2M-4497-2 6/1312
STAR INTERNATIONAL HOLDINGS INC. COMPANY
Star - Holman - Lang - Wells - Bloomfield - Toastmaster
10 Sunnen Drive, St. Louis, MO 63143 U.S.A.
(314) 678-6303
www.star-mfg.com
12