Quick Start Guide
Be sure to install the software programs before connecting the scanner
to the computer!
Setup and Scanning
Check the Package Contents
2
p.
Install the Software
3
Windows
p.
Macintosh
p.
4
USB Interface
IEEE1394 Interface (FireWire)
5
Unlock the Scanning Unit
p.
Connect the Scanner
p.
Try Scanning
p.
6
7
Try the Additional Features
Using the Scanner Buttons
p.10
Scanning Film
11
p.
1
Color Image Scanner Models F916300: (CanoScan 9900F)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable with the ferrite core provided with the scanner is required to comply with Class B limits Subpart B of Part 15
of the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or
modifications should be made, you could be required to stop operation of the equipment.
Canon U.S.A. Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A
Tel No.(516)-328-5600
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Use of a shielded cable with the ferrite core(s) provided with the scanner is necessary to comply with the technical
requirements of the EMC Directive.
Warning
When you use this product, you should pay attention to the following legal issues:
• Scanning of certain documents, such as bank notes (bank bills), government bonds and public certificates, may be
prohibited by law and may result in criminal and/or civil liability.
• You may be required under law to obtain authorization from a person possessing copyrights or other legal rights
to the item being scanned.
If you are uncertain of the legality of scanning any particular item, you should consult your legal adviser in advance.
As an ENERGY STAR Partner, Canon Inc. has determined that this model meets the ENERGY STAR
Program for energy efficiency.
The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving
through the use of computers and other office equipment. The program backs the development and dissemination
of products with functions that effectively reduce energy consumption. It is an open system in which business
proprietors can participate voluntarily. The targeted products are office equipment such as computers, displays,
printers, facsimiles, copiers, scanners and multifunction systems. Their standards and logos are uniform among
participating nations.
•
•
•
•
CanoScan and ScanGear are trademarks of Canon Inc.
Adobe®, Acrobat® and Photoshop® are trademarks of Adobe Systems Incorporated.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the U.S. and other countries.
Macintosh, Power Macintosh, Mac OS and FireWire are trademarks of Apple Computer, Inc., registered in the U.S. and
other countries.
• ScanSoft and OmniPage are trademarks of ScanSoft, Inc.
• Other names and products not mentioned above may be trademarks or registered trademarks of their respective
companies.
In this guide, Windows XP screen shots are used to illustrate explanations common to all operating systems.
1
Guide to the Manuals
Open the Package
Quick Start Guide (this guide)
This guide describes a series of processes, from opening the package to using the
scanner.
READ THIS GUIDE FIRST!
Scanning Guide (HTML format manual)
HTML
Refer to this guide when you have finished setting up the scanner according to the procedures
in the Quick Start Guide. It describes how to utilize the scanner with the bundled software,
and how to solve problems when they occur. You can install this manual onto the hard disk
together with the software programs. When you install it, the Scanning Guide icon will appear
on the desktop. Double-click the icon to view it with a browser program, such as Internet
Explorer.
User’s Guides for Application Programs (PDF format manuals)
PDF
• ArcSoft PhotoStudio
• ArcSoft PhotoBase
• OmniPage SE
• Presto! PageManager (Windows only)
Select the “View the Electronic Manuals” menu on the CanoScan Setup Utility CD-ROM.
To read these manuals, Adobe Acrobat Reader should be installed on your computer.
1
Check the Package Contents
Scanner and Accessories
Scanner
USB Interface Cable
AC Adapter
Film Guides for 35 mm strips/ slides/ 120
and 4”x 5” format films
Documents and Software Programs
• Quick Start Guide (this guide)
• Additional Documents
• CanoScan Setup Utility CD-ROM
• The two figures in the brackets below indicate the respective sizes of the Windows/
Macintosh versions of the software.
• Approximately 514 MB (for Windows) / 275 MB (for Macintosh) of hard disk space on
your computer is required to install all the programs. Additional free hard disk space
is required to operate the programs.
ScanGear CS (25 MB / 5 MB) - Scanner Driver
It allows you to scan and load images from the scanner.
CanoScan Toolbox (5 MB / 3 MB) - Scanning Utility Program
It enables you to scan images and copy (print), attach images to e-mail messages or save images with
simple steps. It also works with the scanner buttons.
ArcSoft PhotoStudio (30 MB / 19 MB) - Image Editing Program
It allows you to load images from the scanner, edit and retouch them, and apply special effects and
enhancements.
ArcSoft PhotoBase (75 MB / 5 MB) - Photo Album Program
It allows you to create and edit image albums, perform image searches and create slide shows.
ScanSoft OmniPage SE (65 MB / 52 MB) - OCR (Optical Character Recognition) Program
It converts characters scanned from a book, magazine or newspaper into text data for editing or
digital transmission.
Presto! PageManager (Windows only) (150 MB) - Digital Document Management Program
It makes it easy to scan, share and organize documents and photos. It automatically links to other
popular programs and avoids file-sharing problems by creating self-executable files.
Adobe Acrobat Reader (24 MB / 24 MB) - PDF File Reader Program
Electronic manuals for the above software programs (HTML (5 MB) and PDF manuals)
• Adobe Photoshop Elements CD-ROM
Adobe Photoshop Elements (135 MB / 162 MB) - Image Editing Program
It loads images from the scanner and allows you to edit and retouch them or apply special effects
and enhancements. Please read the instruction sheet or electronic (PDF) manual for Adobe
Photoshop Elements.
2
Install the Software (Windows)
• With Windows XP/2000, you should log on with
an administrator user name when you install or
uninstall software programs.
1 Turn the computer on.
If the "Found New Hardware Wizard" or
"Add New Hardware Wizard" appears, click [Cancel].
2 Place the CanoScan Setup Utility CD-ROM in the drive.
The CanoScan Setup Utility main menu will display.
3 Click [Install the Software].
Read the SOFTWARE USER LICENSE AGREEMENT. Click [Yes] if
you accept the terms.
The [Install] window will display.
4 Click [Start Installation].
You will install seven software programs and the Scanning Guide
(HTML format manual).
5 The installation procedure will start.
Follow the on-screen message prompts and click [Yes] or [Next]
to continue the installation.
• In few cases, your operating system may
require a restart. Follow the on-screen
messages to restart and resume installation.
6 When the installation is complete, click [Yes].
The computer will restart.
7 After Windows restarts, remove the CD-ROM from
the drive and store it in a safe place.
Continue on p. 5.
3
Install the Software (Macintosh)
When you use a IEEE1394 (FireWire) interface cable, please read
the IEEE1394 caution sheet.
1 Turn the computer on.
If the “...Would you like to look for the software
on the Internet?” appears, click [Cancel].
2 Place the CanoScan Setup Utility CD-ROM in the drive.
The CanoScan Setup Utility main menu will display.
If no window displays, double-click the CD-ROM
icon, then the Setup icon.
3 Click [Install the Software].
Read the SOFTWARE USER LICENSE AGREEMENT. Click [Yes] if
you accept the terms.
The [Install] window will display.
4 Click [Start Installation].
You will install six software programs and the Scanning Guide
(HTML format manual).
5 The installation procedure will start.
Follow the on-screen message prompts and click [Yes], [Next]
or [Install] to continue the installation.
6 When the installation is complete, click [Yes].
The computer will restart.
7 After restarting, remove the CD-ROM from the drive
and store it in a safe place.
4
Unlock the Scanning Unit
• Unlock the scanning unit before connecting the scanner to the computer. If it is left
locked, a malfunction or other problem may occur.
1 Peel the seals from the scanner.
2 Open the document cover and push the lock switch toward the unlock mark (
).
Unlock Mark
Lock Switch
• When transporting the scanner, always lock the scanning unit by pushing the lock switch
toward the lock mark ( ).
• Carrying or transporting the scanner without locking the scanning unit may damage it.
Be particularly careful to lock the scanning unit when transporting the scanner in a
vehicle.
5
Connect the Scanner
• Make sure that the scanning unit is unlocked. (P.5)
1 Peel the caution seals from the scanner.
2 Connect the FAU cable to the scanner.
3 Connect the scanner to the computer with the supplied USB interface cable or a
generic IEEE1394 (FireWire) interface cable.
Supplied USB Interface Cable
Generic IEEE1394 (FireWire) Interface Cable
FAU Cable
FAU Cable
FAU Cable
Wide Flat Connector
FAU Cable
Small Square Connector
USB Interface Cable
IEEE1394 Interface Cable
• You cannot have the USB cable and the IEEE1394 interface cable connected to the
scanner at the same time.
• Please read the IEEE1394 caution sheet bundled with the scanner for precautions
with the IEEE1394 interface and recommended cables by Canon.
4 Attach the supplied AC adapter to the scanner.
AC Adapter
• Only use the USB interface cable and the AC adapter provided with the scanner. Use of
other cables or adapters may lead to a malfunction.
6
Try Scanning
The following steps explain how to scan with ArcSoft PhotoStudio.
1 Press the power switch on the scanner’s front
panel to turn the power on.
Power Switch
2 Place a photo or a picture on the document
glass of the scanner by aligning its top edge
with the alignment mark, and close the
document cover.
Top
Bottom
Alignment
Mark
Windows
3 Select [Start], [Programs] or [All
Programs], [ArcSoft PhotoStudio] and
[PhotoStudio 5].
Macintosh
3 Double-click the [Applications (Mac OS
9)] and [PhotoStudio] folder and the
[PhotoStudio] icon.
PhotoStudio will start.
PhotoStudio will start.
7
Try Scanning
Windows
4 Click the Acquire icon
or click the
[File] menu and select [Acquire].
Macintosh
4 Click the Acquire icon
ScanGear CS will start.
If an error message appears, click the [File]
menu, choose [Select Source], select your
scanner model name and click the [Select]
button.
or click the
[File] menu and select [Import...].
When the [Select Source] dialog displays, select
[ScanGear CS 8.2] and click the [OK] button.
ScanGear CS will start.
5 In the [Select source] category, select [Platen].
6 Select [Type of original].
You can select "Photo", "Magazine", "Newspaper" or
"Document".
• Photo: Color, 400 dpi
• Magazine: Color, 200 dpi
• Newspaper: Black and White, 400 dpi
• Document: Grayscale, 400 dpi
7 Click [Preview].
After calibration, the preview scan will start and gradually
display the image.
The image is automatically cropped at its original size.
If you want to trim the image further, drag the mouse
diagonally to select the area.
8
Try Scanning
8 Click [Scan].
The final scan will start.
9 Click
or
(close box) in the ScanGear CS
window to close it.
The scanned image will appear in the PhotoStudio window.
10 Save the scanned image.
Click the [File] menu and select [Save As]. Select the folder
where you wish to store the image file, enter a file name,
select a file type (JPG format is recommended) and click [Save].
11 Click
or
(close box) in the PhotoStudio
window to close it.
• If the scanner does not perform as described above, read the "Troubleshooting" section
of the Scanning Guide (HTML format manual).
• For details about the bundled software programs, read the Scanning Guide or the User’s
Guide (PDF format manual) for each software program on the CanoScan Setup Utility
CD-ROM.
9
Using the Scanner Buttons
You can use the four convenient buttons on the scanner’s front panel to scan and perform related tasks
easily with a single touch of the button. Place an item on the document glass of the scanner before pressing
a button.
• To use these buttons, ScanGear CS, CanoScan Toolbox, ArcSoft PhotoBase and Presto!
PageManager (Windows)/Acrobat Reader (Macintosh) should be installed from the
CanoScan Setup Utility CD-ROM.
COPY Button
E-MAIL Button
To print (copy) the scanned image with a printer:
To e-mail the scanned image as an attached file:
1 Press the [COPY] button.
2 The scanner will scan the item.
3 The scanned image will print.
1 Press the [E-MAIL] button.
2 The scanner will scan the item.
3 The [E-mail software selection] dialog
• The printer driver should be installed and the
printer should be on-line to use this function.
will appear. Select an option from the
list and click [OK].
This step is required only for the first scan.
4 The e-mail software will start and the
SCAN Button
To open the scanned image in the PhotoBase
window:
1 Press the [SCAN] button.
2 The scanner will scan the item.
3 The scanned image will appear in the
PhotoBase window.
FILE Button
5
scanned image will be attached in a
new message window.
Enter the receiver’s address and title,
write a message, confirm the required
settings, and send the message.
• The e-mail software, such as Outlook Express,
Microsoft Outlook, Eudora or Netscape
Messenger, should be installed and enabled.
With certain e-mail programs, you should
enable the MAPI function (for Windows).
To save the scanned image as a PDF file:
1 Press the [FILE] button.
2 The scanner will scan the item.
3 The scanned image will be saved as a
PDF document and appear in Presto!
PageManager (Windows) or Adobe
Acrobat Reader (Macintosh).
• While scanning, you can change the default settings for scanning by clicking the
[Cancel] button. For changing settings or arranging the scanner button assignments,
refer to the “CanoScan Toolbox” section of the Scanning Guide (HTML format manual).
10
Scanning Film
You can scan 35 mm film (strips or slides) as well as 120 and 4" x 5" format film with this scanner.
Positioning the Film
Use the following procedures to insert the film into the film guide. Make sure that the FAU cable is
connected properly. If the scanner power is not on, press the power switch to turn it on (p. 7).
1 Remove the protective sheet from the document cover.
cd Slide the
protective sheet
up and out to
free it from the
tabs at the top.
ef Slide the sheet
up again and
out to free it
from the tabs at
the bottom.
When you finish scanning, fit the holes at the bottom end of the protective sheet over the tabs at the bottom of the document cover and slide the protective sheet down. Repeat the procedure for the top end.
• Store the protective sheet in a safe place so that it will not get bent or broken.
• Always replace the protective sheet when you are not scanning film to prevent the
light source section from getting scratched.
2 Place the film in the film guide.
35 mm Strips
Pinch to open the film holder on the film guide for 35 mm strips.
Hold the film face down and tuck the ends under the tabs on the film
guide. Pinch the film holder and close it back in position.
If the film holder is not correctly positioned, press down the whole film
holder.
Tab
Two or more film strips in the film holder are scanned in order starting
from the right end of the bottom strip.
120 and 4" x 5" Format Films
Open the film holder on the film guide for 120 and 4" x 5" format
films, place the film face down and close the film holder.
• 120 and 4” x 5” format films cannot be scanned
together at the same time. Place only one in the
film guide at a time
11
Scanning Film
Slides
Position the film guide for slides on the document glass (see Step 3)
and place one or more slides face down in the film guide as shown on
the right.
• If there is a gap between the film guide and the
film, place black paper over the gap to shield it.
3 Place the film guide on the document glass of the scanner.
Align the smaller tab on the side of the film guide with the FILM mark on the document glass of the
scanner.
Calibration Slot
• Do not block the calibration slot on the film guide when you are scanning film.
Colors will not scan correctly if the calibration slot is obstructed.
4 Close the document cover.
Scanning Film
The following steps explain how to scan films with ArcSoft PhotoStudio.
Windows
Macintosh
1 Select [Start], [Programs] or [All
1 Double-click the [Applications (Mac OS
2
2
Programs], [ArcSoft PhotoStudio] and
[PhotoStudio 5].
Click the Acquire icon
or click the
[File] menu and select [Acquire].
ScanGear CS will start.
If an error message appears, click the [File]
menu, choose [Select Source], select your
scanner model name and click the [Select]
button.
12
9)] and [PhotoStudio] folders and the
[PhotoStudio] icon.
Click the Acquire icon
or click the
[File] menu and select [Import...].
When the [Select Source] dialog displays, select
[ScanGear CS 8.2] and click the [OK] button.
ScanGear CS will start.
Scanning Film
3 In the [Select source] category, select [Film].
4 In the [Type of original] category, select [Negative]
or [Positive].
In ScanGear CS’s Simple Mode, the settings for film scanning
are pre-set so that 35 mm film can be scanned and printed at
the photo size. The Output Resolution is pre-set to 200 dpi and
the Print Size to the photo size (8.9 x 12.7 cm/3.5 x 5 in.).
• Use ScanGear CS's Advanced Mode to scan 120 or 4" x 5" format films. See the
Scanning Guide, an HTML format manual, and Precautions when Scanning Film, an
additional document, for instructions for scanning film in Advanced Mode.
5 Click [Preview].
ScanGear CS will display the preview image(s).
Multiple images will appear frame by frame.
• Do not open the document cover while a scan is in progress.
6 Place check mark(s) beside the number(s) of each
frame you wish to scan.
When you scan films with 13 or more frames, click the tab on
the right to view the 13th and subsequent frames.
At first, a check mark only appears beside the first frame. You
can scan multiple frames in one step if you place check marks
beside the numbers of each frame you wish to include.
13
Scanning Film
7 Click [Scan].
The scanner will start scanning the items.
After the scan is complete, click the ScanGear CS close box
(
for Windows or
for Macintosh).
The scanned image will appear in ArcSoft PhotoStudio.
8 Save the scanned image.
Click the [File] menu and select [Save As]. Select the folder
where you wish to store the image file, enter a file name,
select a file type (JPEG format is recommended) and click
[Save].
9 Click
or
(close box) in the PhotoStudio
window to close it.
• If the scanner does not perform as described above, read the "Troubleshooting" section
of the Scanning Guide (HTML format manual).
• For details about the bundled software programs, read the Scanning Guide or the User’s
Guide (PDF format manual) for each software program on the CanoScan Setup Utility
CD-ROM.
• You can purchase the Accessory Kit for CanoScan 9900F (AK-9900F) if the protective
sheet or film guides are lost or damaged.
14
Specifications
CanoScan 9900F
Scanner Type
Flatbed
Scanning Element
CCD 6-line color
Light Source
Cold cathode fluorescent lamp
Optical Resolution
3200 x 6400 dpi
Selectable Resolution
Scanning Bit Depth
Scanning Speed*2
(Photo or Document)
Scanning Speed*2 (Film)
25 - 9600 dpi (ScanGear CS)
Color
Grayscale
16 bit input / 16 bit or 8 bit output for each color (RGB)
16 bit input / 16 bit*1 or 8 bit output
Color
8.64 msec./line (1600 dpi), 8.64 msec./line (3200 dpi)
Grayscale,B&W
8.64 msec./line (1600 dpi), 8.64 msec./line (3200 dpi)
Color, GrayScale,
B&W
2.16 - 146.88 msec/line
Approximately 3 sec.
Preview Speed*3
USB 2.0 Hi-Speed
USB (USB 1.1 equivalent), IEEE1394 (FireWire)
Interface
Maximum Document Size
A4/Letter: 216 x 297 mm (8.5 x 11.7 in.)
35 mm strip (negatives/positives)/24 frames
Film Type/Number of Frames
35 mm slide (negatives/positives)/8 frames
120 format (negatives/positives)12 x 6 cm
4”x 5” format (negatives/positives)
Scanner Buttons
4 buttons: COPY, SCAN, FILE, E-MAIL
Temperature
Operating Range
Humidity
10°C to 35°C (50°F to 95°F)
10% to 90% RH, 20% to 80% RH when scanning film
(without condensation formation)
Power Requirements
AC adapter (100/120/230/240 V)*4
Power Consumption
In operation: 19.5 watts maximum
Stand-by: 6 watts
Power Switch Off: 0.1 watt
(Using supplied AC adapter)
Maximum Exterior Dimensions
Weight
290 x 509 x 127.3 mm (11.4 x 20 x 5 in.)
Approximately 5.2 kg (11.5 lbs.)
*1
Available only when scanning films.
USB 2.0 Hi-Speed mode/IEEE1394 (FireWire) mode. Transfer time to computer is not included.
*3 Calibration processing time is not included.
*4
Type of AC adapter depends on the area where the scanner is purchased.
• Specifications are subject to change without notice.
*2
• Before you upgrade to Windows XP from Windows 98/Me/2000, you must uninstall
ScanGear CS and CanoScan Toolbox using the “Uninstall the Software” menu of the
CanoScan Setup Utility CD-ROM. The scanner may not work if you upgrade to Windows
XP with these programs still installed. After upgrading to Windows XP, reinstall
ScanGear CS and CanoScan Toolbox according to the steps on page 3. For details, please
read the “Troubleshooting” section of the Scanning Guide (HTML format manual).
15
System Information
This form should be used to record the operating environment for the purchased scanner.
If any problems occur with the scanner, you will need this information when you contact our Customer
Support Help Desk. Be sure to record the information and store it in a safe location.
• This information is also required to request a repair under warranty. Make sure you record the
information and store it in a safe location.
• Guaranteed servicing for this equipment will expire seven years after production ceases.
Date of Purchase:
Dealer Tel:
Dealer Address:
Scanner Model:
CanoScan 9900F
Serial Number (on the back of the equipment):
• About the Computer Used
Manufacturer:
Model:
CPU:
Clock Speed:
Memory Capacity (RAM):
MB
Hard Disk Capacity:
MB
OS:
Windows
XP
Macintosh
OS 9.0
Me
OS 9.1
Space Available:
2000
OS 9.2
OS X v10.1
Monitor Size:
Printer:
Manufacturer:
Type of Printer:
Printer Resolutions:
Installed Compression Program:
On-Board Expansion Cards:
Attached Peripherals:
Connected Network System:
16
MB
98
Monitor Type:
Installed Virus Protection Program:
MHz
OS X v10.2
inches
CANON INC.
CANON DANMARK A/S
30-2, Shimomaruko 3-chome, Ohta-ku Tokyo 146-8501, Japan
1. Kund Højgaards Vej1, DK-2860 Søborg, Denmark
Hotline: +45 44 88 25 91
Forhandlerhenvisning:
http://www.canon.dk
CANON U.S.A., INC.
One Canon Plaza, Lake Success, New York 11042, U.S.A.
Customer Care Center: 1-757-413-2848
http://www.usa.canon.com/consumer
CANON NORGE as
Hallagerbakken 110, Postboks 33, Holmlia, 1210 Oslo, Norway
Tlf: 2262 9321 Faks: 2262 0615
http://www.canon.no
CANON CANADA INC.
6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada 1-800-OK CANON
http://www.canon.ca
CANON SVENSKA AB
CANON LATIN AMERICA, INC.
703 Waterford Way, Suite 400 Miami, Florida 33126, U.S.A.
CANON MEXICANA, S. de R.L. de C.V.
Anillo Periferico Sur No. 4124, Torre Zafiro (II) Colonia Ex-Rancho de Anzaldo,
Piso 5 y 6, Mexico D.F.
Tel. (525) 5490-2000
CANON PANAMA, S.A.
Gustav III:s Boulevard 26, S-169 88 Solna, Sweden
Support-Under garantitiden: Tel. 08-744 86 20
Support-Efter garantitiden: Tel. 0900-20 30 555
E-post support: anvandar.klubben@canon.se
http://www.canon.se
CANON OY
Ave. Manquehue Norte #1337, Piso 3, Casilla 187-9 Santiago, Chile
Tel. (562) 366-6600
Kornetintie3, 00380 Helsinki, Finland
Puhelin: 010 54420 Fax: 010 544 4571
Helpdesk: 0600 0 22606 (9,95 mk/min+pvm)
Helpdesk: 0600 0 22666 (enint. 40 mk/puhelu+pvm)
Faksi: 010 544 4382
Sähköposti: helpdesk@canon.fi
Internet: www.canon.fi
CANON ARGENTINA, S.A.
CANON NORTH-EAST OY
Apartado 7022, Panama 5, Rep. de Panama
Tel. (507) 279-8900
CANON CHILE, S.A.
Ave. Corrientes 420 (1043) Buenos Aires, Argentina
Tel. (5411) 432-59800
CANON EUROPA N.V.
P.O. Box 2262 1180 EG Amstelveen, The Netherlands
CANON (UK) LTD.
Woodhatch, Reigate, Surrey RH2 8BF, United Kingdom
For technical support, please contact Canon Help Desk.
P.O. Box 431, Wallington, Surrey SM6 0XU, UK
Tel: (08705) 143 723 (Calls may be recorded)
Fax: (08705) 143 340
For sales enquiries, please call 08705 143723
CANON COMMUNICATION & IMAGE FRANCE S.A.
102 Avenue du Général de Gaulle
92257 LA GARENNE COLOMBES CEDEX, France
Tél: 01.41.30.15.15 Fax: 01.41.30.15.05
E-mail:hot_line@cf.canon.fr
http://www.canon.fr
CANON DEUTSCHLAND GmbH
Europark Fichtenhain A10, 47807 Krefeld, Germany
Technischer Support
Telefax: 0810 / 500 60 22 (0.12€/Min.)
http://www.canon.de
Huopalahdentie 24, P.O. Box 46, FIN-00351 Helsinki, Finland
Tel. +358 10 544 20 Fax +358 10 544 10
http://www.canon.ru
http://www.canon.ee
http://www.canon.lv
http://www.canon.lt
COPICANOLA SA
Rua Alfredo da Silva, 14, 2721-862 Alfragide, Portugal
Tel: 21 471 11 11 Fax: 21 471 09 89
www.copicanola.pt
info@copicanola.pt
CANON SINGAPORE PTE. LTD.
79 Anson Road #09-01/06, Singapore 079906
http://www.canon-asia.com
CANON MARKETING SERVICES PTE. LTD.
No. 1, Jalan Kilang Timor, #09-00 Pacific Tech Centre, Singapore, 159303
Tel: 65-6799-8888, Fax: 65-6273-6786
Hotline: 65-6334-2726
http://www.canon.com.sg
CANON MARKETING (MALAYSIA) SDN. BHD.
Palazzo L, Strada 6, 20089 Milanofiori, Rozzano (MI), Italy
Tel: 02/8248.1 Fax: 02/8248.4604
Pronto Canon: 02/8249.2000
http://www.canon.it
Block D, Peremba Square
Saujana Resort, Section, 40150 Shah Alam, Selangor Darul Ehsan
Malaysia
Tel: 603-7844-6000, Fax: 603-7844-6048
Helpdesk: 603-7844-6008/9
Enquiry: print&scan@canon.com.my
http://www.canon.com.my
CANON NEDERLAND N.V.
CANON MARKETING (THAILAND) CO. LTD.
CANON ITALIA S.P.A
Neptunusstraat 1, 2132 JA Hoofddorp, The Netherlands
Tel: 023-5 670 123 Fax: 023-5 670 124
Helpdesk: 023-5 681 681
http://www.canon.nl
CANON BELGIUM N.V./S.A.
179/34-45 Bangkok City Tower, 9th-10th Floor
South Sathorn Road, Thungmahamek
Sathorn, Bangkok 10120, Thailand
Tel: 662-3449999, Fax: 662-3449968
http://www.canon.co.th
Bessenveldstraat 7, B-1831 Diegem, Belgium
Tel: 02 7220411 Fax: 02 7213274
Helpdesk: 090010627
http://www.canon.be
CANON MARKETING (PHILIPPINES) INC.
CANON LUXEMBOURG S.A.
CANON INDIA Pvt. LTD.
Rue des Joncs 21, L-1818 Howald, Luxembourg
Tel.: (352) 48 47 961 Fax: (352) 48 47 96232
Helpdesk: 900 74100
http://www.canon.lu
CANON Ges.m.b.H.
Zetschegasse 11, 1230 Wien, Austria
Tel.: (01) 680 88-412 Fax: (01) 680 88-413
http://www.canon.at
CANON CEE GMBH
Oberlaaerstr. 233, A-1100 Wien, Austria
Tel: +43 1 680 88-331 Fax: +43 1 680 88-333
CANON (SCHWEIZ) AG
Marvin Plaza Building, 2153 Don Chino Roces Ave,
Makati City, Metro Manila, Philippines
Tel: 632-8126047, Fax: 632-8120067/8109797
Neela Gagan, Mandi Road, Mehrauli, New Delhi-110030, India
Tel: 91-11-6806572, Fax: 91-11-6807180
CANON HONGKONG CO., LTD.
9/F, The Hong Kong Club Building 3A, Chater Road, Central, Hong Kong
TEL: (852) 2739 0802 FAX: (852) 2739 6428
CANON AUSTRALIA PTY. LTD.
1 Thomas Holt Drive, North Ryde, Sydney N.S.W. 2113, Australia
Info-Line: (02) 9805 2864
CANON NEW ZEALAND LTD.
Akoranga Business Park, Akoranga Drive, Northcote Auckland, New Zealand
Info-Line: (09)489 0470
Product Support CCI Industriestrasse 12, 8305 Dietlikon, Switzerland
Fax: 0041 (0) 1 835 68 59
Hotline: 0900 57 55 20 (Fr.2.13/min)
http://www.canon.ch
CANON ESPAÑA S.A.
C/Joaquin Costa, 41-28002, Madrid, Spain
Tel.: 91-538 4500 Fax.: 91-411 4176
Tel: Atención al cliente: 901.301.301
Help Desk: 906.301255
E-mail:helpdesk@btlink.net
I-IE-069A
©CANON INC. 2002
1
PRINTED IN CHINA