Canon 8455B003 Camcorder User Manual

2
Prepare the FINE Cartridges.
Thank you for purchasing the Canon PIXMA MP180/MP160. To prepare your machine for use, please follow
these Easy Setup Instructions before referring to any other documentation.
IMPORTANT
Do not connect the USB cable until after the software is installed. See the reverse side of this sheet for
details.
Remove the protective tape.
Do not touch!
3
1
2
Insert the FINE Cartridges.
Carefully remove all items from the box.
Check the package contents.
• See the flapped lid of the packing box.
3
4
5
Place the machine on a flat surface.
Remove all shipping tape and the protective sheet.
Open the Scanning Unit and remove the protective material (A).
B
C
(A)
• Be sure to hold the machine by the side. Do not lift the machine by grasping the Paper Support Extension
or the Operation Panel.
4
Close the Scanning Unit.
• Lift the Scanning Unit to put the Scanning Unit Support back to its original position.
IMPORTANT
Wait until the preparatory operation is complete; this takes about one to two minutes.
1
2
Connect the power cord.
Press [ON/OFF] to turn
ON the machine.
3
Use [ ] or [ ] on the
Operation Panel to select the language on the LCD, then press [OK]. (MP180)
1
2
Open the Paper Support (1) and pull up the Paper Support Extension (2) until
it stops.
Load the paper with the print side face up.
• Ensure the paper stack does not exceed the Load Limit Mark (A).
3
4
Pinch and adjust the Paper Guide (3) to the width of the stack.
Open the Paper Output Tray.
(1)
• The language setting is only available for some countries.
• If you have an undesired language selection, refer to the User’s Guide.
(3)
(A)
(2)
1
Lift the Scanning Unit and pull the Scanning Unit Support down into place.
The cartridge
moves to the left.
Install the FINE
Cartridges here.
The hardware setup is complete.
If you are connecting the machine to a computer for use, see the reverse side for instructions on
installing the software.
IMPORTANT (US only)
• Write down the serial number. You will need this to register the product.
© 2006 Canon Inc.
All products and brand names are registered trademarks or trademarks of their respective owners.
Specifications subject to change without notice.
QT5-0542-V01
xxxxxxx
© CANON INC. 2006
PRINTED IN VIETNAM
The following software programs are included on the Setup CD-ROM:
Select Easy Install in order to install the application software, On-screen Manual and MP drivers.
Select Custom Install in order to choose the options you would like to install.
This sheet explains Easy Install only.
IMPORTANT
• Close any open software applications, including virus checkers, prior to installing the software.
The following software programs are included on the Setup CD-ROM:
On-screen Manual
MP Drivers
MP Navigator
Easy-PhotoPrint
Easy-WebPrint
ScanSoft OmniPage SE
ArcSoft PhotoStudio
My Printer*
On-screen Manual
Easy-PhotoPrint
*
MP Drivers
MP Navigator
ScanSoft OmniPage SE
*
ArcSoft PhotoStudio
This may not be available depending on the country of purchase.
IMPORTANT
• Do not connect the machine to Mac OS 9 or Mac OS X Classic environments since they are not
supported.
Step 1: Turn ON the machine, and connect the USB cable.
Step 2: Prepare the Setup CD-ROM.
1 Turn ON your computer, and start Mac OS X.
2 Insert the Setup CD-ROM into the CD-ROM drive.
* This may not be available depending on the country of purchase.
IMPORTANT
• Do not connect the USB cable until Step 4, “Connect the USB cable.”
• Before installing the software in Windows XP or Windows 2000, you must log on as Administrator
or a user with Administrator privileges.
• If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop.
3
Double-click [Setup] on the Setup CD-ROM, or click [Setup] on the Setup CDROM and click [File] menu and then select [Open].
Step 3: Enter the name and password for an Administrator Account.
1 Enter the name for the Administrator.
2 Enter the password and then click [OK].
Step 1: Prepare the Setup CD-ROM and get ready to install.
1 Turn OFF the machine.
2 Turn ON your computer, and start Windows.
3 Insert the Setup CD-ROM into the CD-ROM drive.
• The setup program should automatically run. If the setup program does not automatically run, click
[My Computer], then double-click the CD-ROM icon.
Enter
IMPORTANT
If the following screen appears, the USB cable is
connected.
Click
Step 4: Select the language and place of residence.
z Perform the following steps.
1. Turn OFF the machine.
• In some countries, the [Select Language] and [Select Your Place of Residence] dialog boxes will not be
displayed. Go to Step 5.
2. Disconnect the USB cable.
1
3. Click [Cancel].
Select the language to use with this
CD-ROM and then click [Next].
2
Select your place of residence and
then click [Next].
Click
Step 2: Select the language and place of residence.
• In some countries, the [Select Language] and [Select Your Place of Residence] dialog boxes will not be
displayed. Go to Step 3.
1
Select the language to use with this
CD-ROM and then click [Next].
2
Select your place of residence and
then click [Next].
Click
Click
Step 5: Install the software.
1
Click [Easy Install], then click [Install].
• To read descriptions of the software programs, set the mouse on the item.
Click
Click
Click
Step 3: Install the software.
1
Click [Easy Install], then click [Install].
Click
• To read descriptions of the software programs, set the mouse on the item.
2
3
Click [Yes].
• Installation begins. Follow the displayed
instructions.
Click
Click [Restart] to restart your
computer.
Click
Click
• To install Adobe RGB (1998), click Custom Install and follow the instructions on the screen.
• Adobe RGB (1998) cannot be installed in Windows Me and Windows 98
2
Read the License Agreement, then click [Yes].
• Installation begins. Follow the displayed instructions.
Step 4: Connect the USB cable.
1 When the [Printer Connection] appears, connect the machine to the computer
2
3
Click
with the USB cable.
Turn ON the machine.
Click [Exit].
• If prompted to, restart your computer.
US only
• When the Registration window appears, follow the on-screen instructions to ensure product support.
The serial number is located inside the machine. (See “3 Install the FINE Cartridge.” on the reverse side of
this sheet)
* When connecting from Mac OS X v.10.3.3 or earlier:
Restarting the computer while connected to the machine may cause the machine not to be detected. To
resolve this, either unplug the USB cable then plug it back in again, or turn the machine OFF then back
ON again.
z Perform the following to make sure the driver has been installed correctly.
1. Select [Applications] from the [Go] menu.
Click
US only
• When the Registration window appears, follow the on-screen instructions to ensure product support.
The serial number is located inside the machine. (See “Install the FINE Cartridge.” on the reverse side of
this sheet)
2. Double-click the [Printer Setup Utility] ([Print Center] when using Mac OS X v.10.2.8) icon.
If the printer is displayed in the [Printer List], the printer driver is installed.
If the printer is not displayed in the [Printer List], click [Add] in the [Printer List] and select
[USB] from the pop-up menu. Select your machine from the [Product] list and click [Add].
• You can set the scan operation to start with the Operation Panel of the machine. For details, see the User's
Guide.
You now have completed installation of the software.