User`s manual | Canon AXIS 1650 Network Card User Manual

AXIS 1650 User’s Manual
The Network Print & Scan Server for Canon Printers
and Multifunctional Products
Including support for
Canon Advanced Printing Technology
Canon Advanced Raster Printing System
as well as Canon BubbleJet Printers
AXIS 1650 User’s Manual
1
Safety Notices
Section 1
Safety Notices
Take some time to read through the safety notices before installing the print server. Please observe all safety
markings and instructions when using this product.
Important:
Electromagnetic
Compatibility (EMC)
USA
Observe “Important:” in the text to avoid operational impairment. Do not proceed until you have fully
understood the implications.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- reorient or relocate the receiving antenna
- increase the separation between the equipment and receiver
- connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- consult the dealer or an experienced radio/TV technician for help. Shielded (STP) network cables must be
used with this unit to ensure compliance with the class B limits.
Europe
Japan
This digital equipment fulfils the requirements for radiated emission according to limit B of EN55022, and the
requirements for immunity according to EN55024 residential, commercial, and light industry. Compliance is
not valid for unshielded network cables.
This is a class B product based on the standard of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and use the equipment according to the instruction
manual. Compliance is not valid for unshielded network cables.
Australia
This electronic device meets the requirements of the Radiocommunications (Electromagnetic Compatibility)
Standard 1998 AS/NZS 3548. Compliance is not valid for unshielded network cables.
Liability
Every care has been taken in the preparation of this manual; if you detect any inaccuracies or omissions,
please inform your local Axis office, which can be found on www.axis.com. Axis Communications AB cannot
be held responsible for any technical or typographical errors and reserves the right to make changes to the
product and manuals without prior notice. Axis Communications AB makes no warranty of any kind with
regard to the material contained within this document, including, but not limited to, the implied warranties
of merchantability and fitness for a particular purpose. Axis Communications AB shall not be liable nor
responsible for incidental or consequential damages in connection with the furnishing, performance or use of
this material.
Axis’ Trademarks
Other Trademark
Acknowledgments
Patent Information
AXIS IP JumpStarter, AXIS CAPT Print Monitor.
Adobe Acrobat Reader, Canon, Ethernet, Internet Explorer, Microsoft, NetScape, NetSpot Device Installer
(NSDI), Windows, are registered trademarks of the respective holders.
Axis AB has intellectual property rights relating to technology embodied in the product that is described in
this document. In particular, and without limitation, these intellectual property rights may include one or
more of the patents listed at http://www.axis.com/patent.htm and one or more additional patents or pending
patent applications in the US and other countries.
AXIS 1650 User’s Manual
Revision 2.2
Part No: 25081
Date: 06-03-14
Copyright © Axis Communications AB, 2006
2
AXIS 1650 User’s Manual
Table of Contents
Section 2
AXIS 1650 User’s Manual
Table of Contents
Section 1
Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Section 2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Section 3
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About Axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 4
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Section 5
Print Server Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connect the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . 10
Set the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Set an IP Address with NetSpot Device Installer software
14
IP Address Host Names . . . . . . . . . . . . . . . . . . . . . . . . 15
Section 6
Windows Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing Printer Ports using AXIS CAPT Print Monitor 17
Print Server Installation using AXIS CAPT Print Monitor in
Windows 2000, XP and Server 2003 . . . . . . . . . . . . . . 17
Print Server Installation using AXIS CAPT Print Monitor in
Windows 98 and Me . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Print Server Installation using the Standard TCP/IP Port in
Windows 2000/XP/2003 . . . . . . . . . . . . . . . . . . . . . . . 25
Section 7
Adding Printers in NetWare . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setup using NetWare 6.5 . . . . . . . . . . . . . . . . . . . . . . . 28
Setup using NetWare 6.0 . . . . . . . . . . . . . . . . . . . . . . . 34
Section 8
Print Server Management and Configuration . . . . . . . . . . . . 40
Configuration Overview . . . . . . . . . . . . . . . . . . . . . . . . 40
Print Server Management from the Embedded Web Pages
40
Accessing the Web Pages . . . . . . . . . . . . . . . . . . . . . . 41
Services Available from the User Mode . . . . . . . . . . . . 42
Services Available from the Admin Mode . . . . . . . . . . . 44
Setting General Parameters . . . . . . . . . . . . . . . . . . . . . 47
Setting Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Setting Network Protocol Parameters . . . . . . . . . . . . . 49
Print Server Management Using FTP . . . . . . . . . . . . . . 52
Print Server Management Using SNMP . . . . . . . . . . . . 53
Section 9
Scanning with AXIS 1650 . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing AXIS ScanClient . . . . . . . . . . . . . . . . . . . . . .
Using AXIS ScanClient . . . . . . . . . . . . . . . . . . . . . . . . .
Invoking a Scan from your Computer . . . . . . . . . . . . . .
5
5
5
5
54
54
56
56
3
Table of Contents
Invoking a Scan from the Canon Device . . . . . . . . . . . 59
Section 10
The Test Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Section 11
Upgrading the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Section 12
Enabling Unicast Network Communication . . . . . . . . . . . . . 64
Section 13
Internet Connection Firewall in Windows XP SP2 . . . . . . . . 68
Section 14
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4
AXIS 1650 User’s Manual
Preface
Section 3
Preface
Thank you for purchasing the AXIS 1650. This product has been
developed to connect your Canon printer anywhere in your network,
allowing all network users access to shared printer resources.
About this Manual
This manual is applicable for the AXIS 1650 print server with firmware
version 2.00 or later, providing introductory information as well as
detailed instructions on how to set up and manage the print server in
various network environments. It is intended for everyone involved in
installing and managing the print server. To fully benefit from this
manual, you should be familiar with basic networking principles.
These instructions are based on the settings in a new and unconfigured
print server. To reload the default parameters, you can perform a Factory
Default, which will restore all default settings. See “The Test Button” on
page 61.
About Axis
Axis increases the value of network solutions. The company is an
innovative market leader in network video and print servers. Axis'
products and solutions are focused on applications such as security
surveillance, remote monitoring and document management. The
products are based on in-house developed chip technology, which is also
sold to third parties.
Axis was founded in 1984 and is listed on the Stockholmsbörsen
(XSSE:AXIS). Axis operates globally with offices in 14 countries and in
cooperation with distributors, system integrators and OEM partners in 70
countries. Markets outside Sweden account for more than 95 % of sales.
Additional information about Axis can be found at www.axis.com
Support Services
Should you require any technical assistance, please contact your Axis
reseller. If your questions cannot be answered immediately, your Axis
reseller will forward your queries through the appropriate channels to
ensure a rapid response.
AXIS 1650 User’s Manual
5
Preface
If you are connected to the Internet, you can:
•
•
•
•
6
Download user documentation and firmware updates
Find answers to previously resolved problems in the FAQ database.
Search by product, category or phrase
Report problems to Axis support staff by logging in to your private
support area
Visit the Axis support Web: www.axis.com/techsup
AXIS 1650 User’s Manual
Product Overview
Section 4
Product Overview
Package Contents
Hardware
Model
Model/ Part Number
AXIS 1650
0214-001- 01
0214-001- 02
With firmware version 2.00 or higher
AXIX 1650 Japan
0214-005-01
0214-005-02
With firmware version 2.00 or higher
Adhesive Holder & Clip
ACC AXIS CLIPS K
20119
USB Cable
70 cm, 28 inches
USB cable supports USB Low-Speed and
Full-Speed. Hi-Speed is not supported.
20208
Power Adapter
PS-H
Network Print Server
Network Cable
RJ 45 Shielded CAT5 0.5M
16283
CD
AXIS 1650 CD
rev. 1.0 or higher
AXIS 1650 Quick Installation Guide
rev. 1.0 or higher
WARRANTY AXIS SERVERS 1YR
21681
Printed Material
Optional accessories (not
included in package)
Cables
Description
Part Number
Extension Cable
13522
Centronics to Mini Centronics Cable
16453
The AXIS 1650 Network Print Server
Supported Devices
AXIS 1650 is developed to network Canon printers and multifunctional
products. AXIS 1650 supports host-based printing methods such as
Canon Advanced Printing Technology, Canon Advanced Raster Printing
System and other printer types such as Canon BubbleJet.
If your Canon device also functions as a scanner, you can use your AXIS
1650 as a scanner server as well.
Important:
Devices from other manufacturers than Canon are not supported.
AXIS 1650 User’s Manual
7
Product Overview
Supported
Environments
The AXIS 1650 supports printing over TCP/IP from the following clients:
Installation and
Integration
The installation of the AXIS 1650 and its integration into the network is
performed using one of these software combinations:
•
•
•
•
•
•
•
•
•
Windows 98
Windows Me
Windows 2000
Windows XP
Windows Server 2003
Netware
AXIS IP JumpStarter (for IP setting) and then AXIS CAPT Print
Monitor (for printer installation)
Canon NetSpot Device Installer (for IP setting) and then AXIS CAPT
Print Monitor (for printer installation)
AXIS ScanClient to enable scanning through the AXIS 1650.
AXIS IP JumpStarter, AXIS CAPT Print Monitor and AXIS ScanClient
are available free of charge from the AXIS 1650 CD and on
www.axis.com
NetSpot Device Installer is available on www.canon.com
Configuration and
Management
Configuration and management of AXIS 1650 is performed using the
TCP/IP protocol. The main method is using a standard Web browser. See
“Print Server Management from the Embedded Web Pages” on page 40.
Printing Protocol:
TCP/IP
Speed
The AXIS ETRAX chip has been specifically designed for LAN products
and benefits users with a faster throughput than a direct PC-to-printer
connection. With a sustained data throughput of over 1 Mbytes per
second (100baseTX) the AXIS 1650 is fast. ECP high-speed
communication is supported.
Security:
You can assign a password that restricts unauthorized configuration of
the AXIS 1650.
Monitoring:
Future proof:
8
The AXIS 1650 embedded Web pages allow you to continuously monitor
printer status. Additionally, the AXIS 1650 supports SNMP for remote
monitoring.
You can upgrade the AXIS 1650 Flash memory over the network. This
allows you to quickly update and enhance the operational features of
your AXIS 1650 when new print server software becomes available.
AXIS 1650 User’s Manual
Product Overview
Printer Ports
AXIS 1650 User’s Manual
•
One Low- and Full-Speed USB 1.1 port that also works with USB 2.0.
Hi-Speed is not supported.
• One high-speed IEEE 1284 compatible parallel port that plugs directly
into the printer´s parallel port.
AXIS 1650 is featured with two ports for ease of integration with most
Canon printers. There is however no support for handling two connected
printers simultaneously.
9
Print Server Installation
Section 5
Print Server Installation
Follow these steps to install and configure your AXIS 1650:
1. Connect the Hardware, on page 10
2. Set the IP Address, on page 11
3. Windows Installation, on page 17
Connect the Hardware
Parallel printer port (LPT1)
Test button
Network indicator
Ethernet connector
Power adapter
connector
USB Printer Port (USB1)
Power indicator
Backside label of print server
The print server’s MAC/Ethernet address is
based on its serial number (S/N).
Example: If the print server’s serial number
is 00408c181cf0, the Ethernet/MAC
address will be 00-40-8c-18-1c-f0
1. Make sure that your printer is switched off and that the print server’s
power adapter is disconnected.
2. Locate the serial number, found on the underside label of the print server,
and write it down. You will need this number to configure the print server.
3. Either connect the printer to the USB port using the USB cable, or connect
the printer directly to the LPT port or use a printer cable.
Note: AXIS 1650 is featured with two ports for ease of integration with
most Canon printers. There is, however, no support for handling two
connected printers simultaneously.
4. Connect the print server to the network using a shielded twisted pair
(category 5) RJ45 cable, 10baseT or 100baseTX.
5. Switch on the printer and make sure it is ready for use.
6. Connect the power adapter to the print server. The power indicator will light
up. When the network indicator starts to flash, the print server is correctly
connected to the network.
10
AXIS 1650 User’s Manual
Print Server Installation
7. Optionally, you can mount the print server e.g. on the back of the printer
or on a wall, using the supplied clip and holder.
Adhesive Holder
Fasten to print server by peeling off adhesive tape.
Adhesive Clip
Fasten to mounting surface by peeling off adhesive
tape.
Set the IP Address
Before setting the IP address, make a note of the print server’s serial
number (S/N), located on its backside label. See Backside label of print
server, on page 10.
You should obtain an unused IP address from your network administrator
Method
AXIS IP JumpStarter
software
Platform
Windows
Comment
Axis software that allows you to find print servers in your network
and assign an IP address to them.
See “Set a Static IP Address using AXIS IP JumpStarter” on page 11
Windows
See “Set a Static IP Address using ARP in Windows
98/Me/2000/XP/2003” on page 13
Unix/
Linux
See Set a Static IP Address using ARP in UNIX, on page 13
Arp/Ping
Canon’s NetSpot
Device Installer software
Windows
Canon software that allows you to find print servers in your network and assign an IP address to them.
See “Set the IP Aaddress using NetSpot Device Installer” on page 14
It is not possible to obtain a dynamic IP address using DHCP, since DHCP
is disabled by default in AXIS 1650. To enable DHCP in the print server,
see DHCP Enabled, on page 50. You can, however, obtain a DHCP address
for the print server via AXIS IPJumpStarter or NetSpot Device Installer. If
you choose to obtain a DHCP address for the print server from these
programs, the DHCP function will be enabled in the print server.
Set a Static IP
Address using AXIS IP
JumpStarter
AXIS 1650 User’s Manual
AXIS IP JumpStarter is an application that helps you to locate your Axis
print server on the network and assign an IP address to it.
11
Print Server Installation
1. Install AXIS IP JumpStarter, it is available on the AXIS 1650 CD and on
www.axis.com
2. Select a print server from the Serial Number list. All AXIS 1650 appear with
the default IP address 192.168.0.90. If you are installing several AXIS 1650,
check the Serial Number to locate a specific print server.
All AXIS 1650 have the default IP address 192.168.0.90
Change this default IP address to either a
static IP address or to a DHCP address.
3. From the Server menu, select Set IP Address. The Set IP Address dialog
appears.
4. Click the radio button that corresponds to your choice of IP setting method
(static or dynamic using DHCP). When assigning a static IP address you also
have to define the Subnet Mask and Default Gateway.
5. Click OK to save your settings.
6. You may be prompted to enter the server root password (by default set to
<blank>), click OK and the print server will appear in the list with the
assigned IP address.
7. To verify that you have access to the print server’s Web pages, highlight the
print server in the list and select Server Home Page from the Server menu.
8. You have now finished the procedure of setting the IP address. Continue to
Windows Installation, on page 17.
12
AXIS 1650 User’s Manual
Print Server Installation
Set a Static IP
Address using ARP in
Windows
98/Me/2000/XP/2003
1. Open a Command Prompt and type:
arp -s <IP address> <Ethernet address>
ping -l 479 <IP address>
Example:
arp -s 192.168.3.191 00-40-8c-18-1c-f0
ping -l 479 192.168.3.191
2. If the host returns Reply from 192.168.3.191 ... or a similar message,
the IP address has been set successfully.
If the host returns Request timed out you need to reboot the print server and
perform steps 1-2 above again. Rebooting the print server is done by
disconnecting and then re-connecting the print server’s power adapter.
3. Access the print server’s Web pages ( - See page 41), select Admin | Network
Settings | Detailed View | TCP/IP and define the Default Router and Subnet
Mask. Make sure DHCP, BOOTP and RARP are disabled.
You have now set the IP address of the print server. Continue with
Windows Installation, on page 17.
Note:
Set a Static IP
Address using ARP in
UNIX
When you execute the ping command for the first time, you will
experience a significantly longer response time than usual.
Follow the instructions below to set the IP address using ARP.
1. Type the following commands in the shell window:
arp -s <ip address> <Ethernet address> temp
ping -l 479 <ip address>
Example:
arp -s 192.168.3.191 00:40:8c:18:1c:f0 temp
ping -l 479 192.168.3.191
2. The host will return 192.168.3.191 is alive or a similar message. This
indicates that the address has been set and that the communication is
established.
3. Access the print server’s Web pages ( - See page 41), select Admin | Network
Settings | Detailed View | TCP/IP and define the Default Router and Subnet
Mask. Make sure DHCP, BOOTP and RARP are disabled.
Notes:
•
•
AXIS 1650 User’s Manual
The ARP command varies between different UNIX systems. Some BSD
type systems expect the host name and node address in reverse order.
When you execute the ping command for the first time, you may
experience a significantly longer response time than usual.
13
Print Server Installation
Set an IP Address with NetSpot Device Installer software
NetSpot Device Installer is software from Canon that allows you to assign
an IP address and manage Canon devices connected to your network.
NetSpot Device Installer software is supplied on CD-ROM with your
Canon printer and on www.canon.com
Depending on the provided CD-ROM, NetSpot Device Installer may not be
included. If this is the case, please download NetSpot Device Installer
from www.canon.com
Install NetSpot Device
Installer
1. In Windows 2000/XP, log on as an Administrator before installing. Insert
the CD-ROM supplied with your Canon printer into the CD-ROM drive of
your computer.
2. In Windows Explorer, double-click the CD-ROM drive icon.
3. Double-click NetSpot_Device_Installer => Windows => nsdisetup.exe
4. A license agreement will be shown in the window. Check the contents and
click Yes.
5. Specify the program destination folder and click OK. The installation will
launch.
If you check “Add to Start menu”, you can add NetSpot Device Installer to
your Windows Start menu.
6. When the installation is finished, click OK. You can now start the program,
see Set the IP Aaddress using NetSpot Device Installer, on page 14.
Set the IP Aaddress
using NetSpot Device
Installer
Follow these instructions to set the IP address using NetSpot Device
Installer:
1. Start the program. The main window will open. After a while a list of
devices detected on the network will be displayed.
2. Select the AXIS 1650 that displays the unit’s MAC address and default IP
address 196.168.0.90
The MAC address is based on the Serial Number (S/N) of your AXIS 1650 and
is printed on the underside label of the print server.
3. From the Device menu, select Initial Settings.
14
AXIS 1650 User’s Manual
Print Server Installation
4. From the Initial Settings dialogue box, select the AXIS 1650 print server
from the Product Type drop-down list and click Next.
5. Next, configure the TCP/IP protocol:
Select Manual Setting
Enter IP Address
Enter Gateway Address
Enter Subnet Mask
The Broadcast Address is
filled in automatically
6. After you have finished the configuration, click OK.
Note: If you get a message reading “Resetting device”, click OK.
7. Click OK. Your printer’s protocol configuration is now finished and your AXIS
1650 has received an IP address. Continue to Windows Installation, on page
17.
IP Address Host Names
If you are using host names, you can map a unique host name to the IP
address. Refer to your system manuals or to your network administrator
for instructions on how to perform name mapping on your system.
AXIS 1650 User’s Manual
15
Print Server Installation
Notes
•
•
•
•
•
•
•
•
16
You need to know the Ethernet address of your AXIS 1650 to perform
the installation. The Ethernet address is based on the serial number of
your AXIS 1650. For example, an AXIS 1650 with the serial number of
00408C181CF0, will have the corresponding Ethernet address of 00 40
8C 18 1C F0. The serial number is located on a label on the backside of
the print server.
DO NOT use the IP addresses shown in the following examples when
installing the AXIS 1650.
ARP/Ping operates on single network segments only, i.e. it cannot be
used over routers.
The default host name of the print server is ’AXIS’ followed by the last 6
digits in the serial number. e.g. AXIS181636. The host name is changed
in the Print server name field in Admin | General Settings.
The host name limitations conclude that if you want to register the
same host name at a WINS server and a DDNS server, the host name
should be no longer than 15 characters and it should only contain the
characters ‘A-Z’, ‘a-z’, ’0-9’ and ‘-’.
Refer to your system manuals or to your network administrator for
instructions on how host name resolutions are performed on your
system.
At least one WINS server IP address must be included in the DHCP
scope if you are using WINS. Immediately after the IP address has been
received, the AXIS 1650 registers its host name and IP address on the
WINS server.
If the host name has not been mapped to the IP address, you can still
perform the following instructions to download the IP address. In this
case, simply replace the host name entry with the IP address wherever
required.
AXIS 1650 User’s Manual
Windows Installation
Section 6
Windows Installation
Installing Printer Ports using AXIS CAPT Print Monitor
AXIS CAPT Print Monitor is a Windows component that has been
developed for network printing. AXIS CAPT Print Monitor is the
recommended tool for Canon printers, including CAPT, Canon Advanced
Raster Printing System and BubbleJet.
AXIS CAPT Print Monitor allows your AXIS 1650 to be connected in the
same simple fashion as a local printer port and once installed, it is
automatically initialized upon system start-up.
AXIS CAPT Print Monitor needs to be installed on each workstation for
peer-to-peer printing.
Refer to the instructions relevant to your network on how to install a
printer using AXIS CAPT Print Monitor:
•
•
Print Server Installation using AXIS CAPT Print Monitor in Windows
2000, XP and Server 2003, on page 17.
Print Server Installation using AXIS CAPT Print Monitor in Windows 98
and Me, on page 22.
See also Print Server Installation using the Standard TCP/IP Port in
Windows 2000/XP/2003, on page 25.
Print Server Installation using AXIS CAPT Print Monitor in Windows 2000, XP and Server 2003
1. Install the AXIS CAPT Print Monitor on your workstation. The software is
available on the AXIS 1650 CD and on www.axis.com
2. Launch the software installation and click Next.
AXIS 1650 User’s Manual
17
Windows Installation
3. Read the License Agreement and click Yes if you accept the terms.
4. Leave this check-box unchecked* and click Next. (If you want to disable
broadcast status updates and enable unicast, see Enabling Unicast Network
Communication, on page 64.)
Windows XP/Server 2003 only:
Make sure the Allow this application to process incoming network printer
information on the local subnet checkbox is checked.
Must be checked!
In Windows XP SP 2, UDP port 10260 must be open in the Internet
Connection Firewall when using Broadcast communication. UDP port
10260 is opened automatically in the Internet Connection Firewall when
18
AXIS 1650 User’s Manual
Windows Installation
Windows XP SP2 is installed, if Allow this application to process
incoming network printer information on the local subnet is checked.
5. Click Finish to finish the installation.
6. Windows XP/Server 2003:
Go to Start | Printers and Faxes and click the Add a Printer icon to start
the Add Printer Wizard.
(Windows XP Home Edition: Start | Control Panel | Printers and Faxes | Add
a Printer).
Click Next.
Windows 2000:
Go to Start | Settings | Printers and click the Add Printer icon to
start the Add Printer Wizard. Click Next.
AXIS 1650 User’s Manual
19
Windows Installation
7. Select Local Printer attached to this computer. Make sure the
Automatically detect and install my Plug and Play printer check box is not
checked. Click Next.
8. Click the Create a new port radio button and select AXIS CAPT Port. Click
Next.
Note: AXIS CAPT Port is used for all Canon printers, including CAPT,
Canon Advanced Raster Printing System and BubbleJet.
20
AXIS 1650 User’s Manual
Windows Installation
9. The AXIS CAPT Port pop-up window will appear. Select your AXIS 1650 from
the Available network printers list and click OK.
If your AXIS 1650 doesn’t appear in the
Available network printers list, enter its IP address and click Add.
10. Select Manufacturer and Printer from the driver list. Click Next.
11. Choose whether you want to keep the existing driver or to replace it. If you
already have the printer’s driver installed, you will be asked whether to keep
it or to replace it.
12. Click Next. Supply a name for the printer and choose whether you want to
make it your default printer. Click Next.
13. Choose whether you want to share the printer with other network users,
print a test page, etc. Select the appropriate radio button and click Next and
Finish.
AXIS 1650 User’s Manual
21
Windows Installation
14. Print a test page to verify. You have now completed the installation.
Print Server Installation using AXIS CAPT Print Monitor in Windows 98 and Me
Follow the procedure below to install TCP/IP Ports from a Windows
98/Me workstation:
1. Install the AXIS CAPT Print Monitor on your workstation. The software is
available on the AXIS 1650 CD and on www.axis.com
2. Launch the software installation and click Next.
3. Read the License Agreement and click Yes if you accept the terms.
22
AXIS 1650 User’s Manual
Windows Installation
4. Leave this check-box unchecked and click Next.
(If you want to disable broadcast status updates and enable unicast, See
Enabling Unicast Network Communication, on page 64 for instructions.)
5. Click Finish to finish the installation.
6. Select Settings | Printers from the Start menu and double-click the Add
Printer icon to start the Add Printer Wizard.
7. Select Local Printer, as the AXIS 1650 emulates a local printer port and click
Next>
8. Choose an appropriate printer driver for your printer.
If the desired driver appears in the manufacturer and models list dialog,
highlight your selection and click Next>.
If the desired printer driver is not available, click the Have Disk... button.
Insert the printer driver CD that was provided with your printer, select the
CD drive and click OK.
9. Select the desired printer driver from the CD and click Next>
AXIS 1650 User’s Manual
23
Windows Installation
10. Select the port you wish to use and click OK.
•
•
The ports will appear in the format <name>.
<name> is, by default, ‘AXIS’ followed by the last six digits
of the print server’s serial number. Example: AXIS560B35.
If you wish to install a remote TCP/IP port (and if the TCP/IP
port does not appear in the list), select the LPT1 port. Continue
with steps 11 and 12 and then follow the Remote Printer Port
instructions below.
11. Enter a descriptive name for your printer and click Next>
12. Click the checkbox if you want to print a test page and click Finish.
Remote Printer Port
1. The printer you defined above is now displayed in the printers folder.
Right-click the printer object and select Properties from the menu.
2. Click the Details tab and click Add Port... to display the available print server
monitors.
3. Click Other, select AXIS CAPT Port and click OK.
AXIS CAPT Port is used for all Canon printers, including CAPT, Canon
Advanced Raster Printing System and BubbleJet.
4. Enter the IP address / host name of your print server. Click Add.
5. The port will be added to the list and highlighted. Click OK to return to the
printer ports dialog and click Close.
24
AXIS 1650 User’s Manual
Windows Installation
Print Server Installation using the Standard TCP/IP Port in Windows 2000/XP/2003
Follow the instructions below to use the Windows Standard TCP/IP Port
to add a network printer in Windows 2000/ Windows XP/2003.
Windows XP/ Server 2003:
1. Go to Start | (Settings) | Printers and Faxes and click the Add a Printer
icon to start the Add Printer Wizard. Click Next.
Windows 2000:
1. Go to Start | Settings | Printers and click the Add Printer icon to start
the Add Printer Wizard. Click Next.
2. Select Local Printer attached to this computer and make sure the
Automatically detect and install my Plug and Play printer check box is not
checked. Click Next.
3. Click the Create a new port radio button and select Standard TCP/IP Port
from the list. Click Next and the Add Standard TCP/IP Printer Port Wizard
starts. Click Next.
AXIS 1650 User’s Manual
25
Windows Installation
4. In the Printer Name or IP Address field, enter the IP address of the print
server. Example: 192.168.3.191.
The Port Name field will be filled in automatically. Click Next.
5. Select Manufacturer and Printer from the lists.
Click Next.
6. If you already have the printer’s driver installed, you will be asked whether
to keep it or to replace it. Click Next. Supply a name for the printer and
choose whether you want to make it your default printer. Click Next.
7. Choose whether you want to share the printer with other network users,
print a test page, etc. Select the appropriate radio button and click Next and
Finish.
26
AXIS 1650 User’s Manual
Windows Installation
8. Next, from your desktop, go to Start | Printers (and Faxes). Highlight the
installed printer and right-click, choose Properties, then Ports | Configure
Port.
9. In the LPR Settings - Queue Name field, you will see the value "z". In the
Queue Name field, type USB1 or LPT1, depending on which printer port you
are using. Click OK and then Apply.
10. Print a test page to verify. You have now finished the installation.
AXIS 1650 User’s Manual
27
Adding Printers in NetWare
Section 7
Adding Printers in NetWare
This section describes how to continue the installation of the AXIS 1650
in a NetWare environment.
iPrint
Using iPrint in the NetWare environment, users simply point to a Web
page that displays all printers available for installation. By clicking a
printer, the iPrint client is installed (if not installed previously), the
printer's driver is downloaded, and a printer is created on the user's
workstation; thus, the user will be able to send documents to the printer
from any application on the desktop.
Depending on your NetWare version, go on to “Setup using NetWare 6.5”
on page 28 or “Setup using NetWare 6.0” on page 34.
If you intend to operate your AXIS 1650 in a multi-protocol, mixed
environment, you should also proceed to the other relevant sections in
this manual.
Setup using NetWare 6.5
Start the iManager. Type https://<mapped name to file server sys
volume>/nps/iManager.html in the Address/Location field of your
browser and press Enter.
Example: https://nakoma.tl.com/nps/iManager.html.
In the Roles and Tasks frame of the iManager, expand iPrint to make all
commands available.
Check Print Manager
and Broker
Make sure that NDPS is installed and that the Print Manager and the
Broker both are loaded on your NetWare file server.
You can check the status of NDPS by selecting Roles and Tasks | iPrint |
Manage Print Manager, browse to the file server and select it. Ensure that
the status is NDPS Manager active.
28
AXIS 1650 User’s Manual
Adding Printers in NetWare
To check the state of the Broker, select Roles and Tasks | iPrint | Manage
Broker. Its state has to be active as well.
Create a Printer
In the iManager, click Roles and Tasks | iPrint | Create Printer.
The Create Printer dialogue appears.
Type a name for the printer to be created (e.g. CanonMF).
Keep the default Container name (e.g. axis).
Select Print Manager name (e.g. NAKOMA_MANAGER.axis).
Select Novell gateway as Gateway type and click Next.
Configure Novell
Gateway for the
Created Printer
To configure the gateway, enter Host IP address or Host name of the
AXIS 1650 (e.g. 171.15.114.137).
As default, PASSTHROUGH is suggested as LPR Printer name. Change
this to USB1 or LPT1, depending on which device port the print server is
connected to (or simply select the Port 9100 radio button for raw
printing).
Click Next.
AXIS 1650 User’s Manual
29
Adding Printers in NetWare
Select Default Drivers
for Your Platforms
For each platform in your network, select the default printer drivers to
install (the drivers presented are those registered in the Broker; new
drivers can be added from the Manage Broker task). Click Next.
You will now receive a confirmation that the request succeeded and that
printer CanonMF.axis was created. Click OK.
Manage the Newly
Created Printer
To Browse for a Printer
30
Select Roles and Tasks | iPrint | Manage Printer and specify which
NDPS Printer to modify (e.g. CanonMF.axis). Click OK.
Next to the NDPS Printer name field, click the Browse icon. Browse to your
default container to find the newly created printer (e.g. CanonMF), select
AXIS 1650 User’s Manual
Adding Printers in NetWare
it in the Contents list and click Apply.
Check Printer Health
AXIS 1650 User’s Manual
Select Roles and Tasks | iPrint | Manage Printer | Printer Health
Monitor to check the health of the printer.
31
Adding Printers in NetWare
Click Back to return to the Manage Printer main page.
Enable iPrint Support
In the Manage Printer main page, click the Client Support tab.
To enable iPrint support, check Enable iPrint support, click Apply and
OK.
Make the Newly
Created Printer
Available (Optional)
Using the iPrint Map Designer tool, you can quickly make the newly
printer available and accessible simply by clicking on its icon in a floor
plan, showing where the printers are located.
The tool lets you import own floor plans as background images that can
be used to drag-and-drop printers onto actual locations. These maps are
then published on a Web server so users can install printers that are
closest to their location.
1. Using Microsoft Explorer, start maptool.html, which can be found in
<sysvol>\Apache2\htdocs\ippdocs\.
2. Select a map from the Background drop-down list.
3. Select a Printer icon for the newly created printer and drag it to a suitable
position in the design area, i.e. the floor plan.
4. Next to the Printer List field, click the Browse icon and enter the IP address
or DNS name of the server where the Print Manager is running (e.g.
171.15.115.112).
32
AXIS 1650 User’s Manual
Adding Printers in NetWare
5. From the Printer List, select the printer agent you want associated with this
printer icon (e.g. CanonMF). The Printer URL and Mouse Over Text will
automatically be filled in with the printer agent information.
Printer URL is the URL created for the printer when IPP was enabled for the
printer (e.g. ipp://171.15.115.112/ipp/CanonMF). You should not need to
change the URL.
The Mouse over text will by default display the printer agent's name. You
can override this information by entering the text you want to display when
a user moves the mouse over the printer icon (e.g. Canon Multifunction).
6. In the Printer caption field, enter the information to display (e.g. AXIS
1650/Canon MF).
7. Click Save and save the map (e.g. as AXIS1650_usb).
Installing the Printer
Locally
The printer is now accessible all over the network and will be installed on
any client when needed. In case you need to install the printer locally, use
Windows’ Add Printer Wizard in the usual manner:
1. Ensure that iPrint Client is installed.
2. Start | Printers and Faxes | Add a printer.
3. Select Network printer and Browse for a printer.
4. Select NDPS Printers, select NDPS Controlled Access Printers.
AXIS 1650 User’s Manual
33
Adding Printers in NetWare
5. Select Container (e.g. Axis) and the printer (e.g. CanonMF).
6. Wait for the printer to be installed.
7. Finally, print a test page.
Setup using NetWare 6.0
Setting up iPrint in a NetWare 6.0 environment is rather similar to
performing the same task in the 6.5 version.
Launch the iManager
From a workstation, launch your browser and enter the following URL:
https://<server_ip_address:port_number>/eMFrame/iManager.html. Note
that this URL is case sensitive. The server IP address can also be a DNS
name. Example: https://171.15.115.109:2200/eMFrame/iManager.html
To have full access to all iManager features, you must log in as Admin of
the tree.
Check Print Service
Manager and Broker
Create a Printer
Make sure that NDPS is installed and that the Print Service Manager and
the Broker both are loaded on your NetWare file server.
In the left frame, expand iPrint Management to make all commands
available and click Create Printer.
In the Create Printer dialogue, enter the information needed.
Examples:
Printer name: CanonMF
Container name: axis
Manager name: SIXPACK_MANAGER.axis
Gateway type: Novell LPR gateway (LPR or IP)
Click Next.
34
AXIS 1650 User’s Manual
Adding Printers in NetWare
Configure Novell LPR
Gateway for the
Created Printer
To configure the gateway, enter Host IP address of the AXIS 1650 (e.g.
171.15.114.137). Instead of the Host IP address you can use the Host
name (e.g. CanonMF.tl.com).
As Printer name, enter the printer port (e.g. USB1). Click Next.
Select Default Drivers
for Your Platforms
For each platform in your network, select the default printer drivers to
install (the drivers presented are those registered in the Broker; new
drivers can be added from the Manage Broker task). Click Next.
You will now receive a confirmation that the request succeeded and that
printer CanonMF.axis was created. Click OK.
Manage the Newly
Created Printer
To Browse for a Printer
AXIS 1650 User’s Manual
In the left frame of the iManager, select iPrint Management | Manage
Printer and specify which NDPS Printer to modify (e.g. CanonMF.axis).
Click OK.
Next to the NDPS Printer name field, click the Browse icon. Browse to your
35
Adding Printers in NetWare
default container to find the newly created printer (e.g. CanonMF), select
it in the Contents list and click Next.
Check Printer Health
Select Printer Health Monitor to check the health of the printer.
Click Back to return to the Manage Printer main page.
36
AXIS 1650 User’s Manual
Adding Printers in NetWare
Enable IPP Access
In the Manage Printer main page, click the Client Support tab.
To enable IPP access, check Enable IPP access, click Apply and OK.
Make the Newly
Created Printer
Available (Optional)
Using the iPrint Map Designer tool, you can quickly make the newly
printer available and accessible simply by clicking on its icon in a floor
plan, showing where the printers are located.
The tool lets you import own floor plans as background images that can
be used to drag-and-drop printers onto actual locations. These maps are
then published on a Web server so users can install printers that are
closest to their location.
1. Using Microsoft Explorer, start maptool.html, which can be found in
<sysvol>\login\ippdocs\.
2. Select a map from the Background drop-down list.
3. Select a Printer icon for the newly created printer and drag it to a suitable
position in the design area, i.e. the floor plan.
4. Next to the Printer List field, click the Browse icon and enter the IP address
or DNS name of the server where the Print Manager is running (e.g.
171.15.115.109).
5. From the Printer List, select the printer agent you want associated with this
printer icon (e.g. CanonMF). The Printer URL and Mouse Over Text will
automatically be filled in with the printer agent information.
Printer URL is the URL created for the printer when IPP was enabled for the
printer (e.g. ipp://171.15.115.109/ipp/CanonMF). You should not need to
change the URL.
The Mouse over text will by default display the printer agent's name. You
can override this information by entering the text you want to display when
a user moves the mouse over the printer icon (e.g. CanonMF).
6. In the Printer caption field, enter the information to display (e.g. AXIS 1650
Canon MF).
7. Click Save and save the map (e.g. as AXIS1650_usb).
AXIS 1650 User’s Manual
37
Adding Printers in NetWare
Installing the Printer
Locally
The printer is now accessible all over the network and will be
automatically installed on any client when needed.
In the HTML-page just created, double-click the new printer icon. A
dialogue box will appear, waiting for confirmation:
Click OK to start installation and iPrint will report progress during all
stages of local installation.
38
AXIS 1650 User’s Manual
Adding Printers in NetWare
Manual Installation of
the Printer Locally
In case you need to install the printer locally, use Windows’ Add Printer
Wizard in the usual manner:
1. Ensure that iPrint Client is installed.
2. Start | Printers and Faxes | Add a printer.
3. Select Network printer and Browse for a printer.
4. Select NDPS printers, select NDPS Controlled Access Printers.
5. Select Container (e.g. Axis) and the printer (e.g. CanonMF).
6. Wait for the printer to be installed.
7. Finally, print a test page.
AXIS 1650 User’s Manual
39
Print Server Management and Configuration
Section 8
Print Server Management and Configuration
The management and configuration tools that are supported by the AXIS
1650 allow you to:
•
•
•
•
Change print server parameters
Receive extended information about print jobs
Receive printer port status and monitor printers
Reset the AXIS 1650
Configuration Overview
The method you should use to manage and configure your AXIS 1650 is
dictated by your TCP/IP network.
Configuration/Management methods:
•
•
•
Embedded Web Pages using a Web Browser - See page 40.
FTP - See page 52.
SNMP - See page 53.
Print Server Management from the Embedded Web Pages
All Axis print servers contain an embedded Web server that can be
accessed through a Web browser. The embedded Web server provides
access to configuration and management pages for the print server and
the connected printer.
Once you have established the AXIS 1650 in the TCP/IP environment, as
described in Set the IP Address, on page 11, you can access the AXIS
1650 Web pages from any standard Web browser.
The Web interface has two modes of operation: User mode and Admin
mode.
40
User Mode
In User mode you can change language of the Web interface, but you
have no rights to change any other parameters. This mode is intended for
regular users who are only interested in using the print server's interface
for checking print jobs or viewing printer properties. If you want to
change any other settings, you must enter the Admin mode. See “Services
Available from the User Mode” on page 42.
Admin Mode
When in Admin mode, you have access to all the print server's parameters
and you can change them after your needs. This mode is intended for
network administrators and can be password protected to prevent
unauthorized changing of parameters. See “Services Available from the
Admin Mode” on page 44.
AXIS 1650 User’s Manual
Print Server Management and Configuration
Print Jobs
Select Print Jobs to view Printer Usage, showing the accumulated usage
of the printer connected to your print server. The Printer Usage log is
erased each time the print server is restarted.
•
•
•
•
View Job Log
Print Server Uptime
Scanner
Help
AXIS 1650 User’s Manual
Printer - shows the printer model.
Port - shows the port to which the printer is connected.
Status - shows the status of the printer. The available status messages
are ready, busy and off-line.
Printed Pages - shows the number of pages that the printer has printed
(not shown for all printer models).
Presents the 32 latest print jobs as Document Name, Owner, Page Count,
Time and Print Results. Note that the time when the document was
printed is only available if the print server has access to a time server.
Shows the time elapsed since last time the print server was restarted.
Shown for multifunctional Canon devices with scanning capabilities. If
the scanner is in use, its status will change from Idle to Busy and the User
name will be shown.
The Help pages present basic information about the AXIS 1650 and its
Web user interface.
43
Print Server Management and Configuration
Services Available from the Admin Mode
Click on the Axis logotype to reach Axis’ home page.
A click on the question mark will open the print server’s help pages.
The following services are available from the Admin mode.
This Print Server
Print Server Name
System Location
Serial Number
General Settings
This page contains a section that allows you to view and modify the
general parameter settings of the AXIS 1650. Management operations,
like restarting the AXIS 1650 and resetting its parameters to their default
settings are also available.
This name identifies the print server to the users. The default name is
AXISXXXXXX, where XXXXXX are the last six digits of the print
server’s serial number.
This parameter shows where the print server is located, helping you to
find the Canon device you are working with.
Every Axis device is uniquely identified by its serial number. The serial
number is found on the underside label of your print server. See “Print
Server Installation” on page 10.
In this section, you manage the print server’s general settings as well as
permissions.
To change the print server’s general parameters, select Admin | General
Settings => Change. For additional information, see “Setting General
Parameters” on page 47.
To change print server permissions and restrictions, select Admin |
General Settings => Change and select the Restrictions tab. For additional
information, see “Setting Restrictions” on page 48.
Parameter List
Restart
Software Default
Click Detailed View to see all parameters and their current settings.
Restarts the print server. When the power LED lights constantly and the
Network indicator starts flashing to indicate network activity, the print
server is ready for use again. New configuration settings will then become
active. All contact with the printer server will be lost during a restart.
A Software Default will reset all print server parameters to their factory
default settings except:
•
•
•
Node address (NODE_ADDR.)
IP address (IP_ADDR.)
DHCP enabled or disabled (DHCP_ENABLE.)
A Software Default differs from a Factory Default. A Factory Default is
performed by pressing the Test button, located on the print server, in a
specific sequence. See “The Test Button” on page 61.
When the power LED lights constantly and the Network indicator starts
flashing to indicate network activity, the print server is ready for use
again.
44
AXIS 1650 User’s Manual
Print Server Management and Configuration
Printer Page
By clicking the printer icon on the This Print Server page, a Printer page
opens, allowing you to view the status and the supported capabilities of
the connected printer.
On some printer models, you can also print a test page from the Printer
page. Note: It is only possible to print a test page on Canon printers that
support printing standard ASCII characters. It is not possible to print a
test page on Canon printers supporting Canon Advanced Printing
Technology and Canon Advanced Raster Printing System.
Underneath the printer icon is a colored symbol that indicates the status
of the printer:
•
•
•
A
green indicates that the printer is ready for printing
yellow indicates warning
red indicates error
dimmed printer indicates that no printer is connected to that port.
Printer Status
The printer page shows status and capabilities of the printer that is
connected to the selected printer port. The capabilities include Detailed
Status, Manufacturer, Command Sets and Capabilities. The extent of this
information depends on the printer model.
Network Names
Click Network Names to see a list of names that the printer is identified
with in the supported network environments.
Print Jobs
Select Print Jobs to view Printer Usage, showing the accumulated usage
of the printer connected to your print server. The Printer Usage log is
erased each time the print server is restarted.
•
•
•
•
View Job Log
Print Server Uptime
Scanner
AXIS 1650 User’s Manual
Printer - shows the printer model.
Port - shows the port to which the printer is connected.
Status - shows the status of the printer. The available status messages
are ready, busy and off-line.
Printed Pages - shows the number of pages that the printer has printed
(not shown for all printer models).
Presents the 32 latest print jobs as Document Name, Owner, Page Count,
Time and Print Results. The time when the document was printed is only
available if the print server has access to a time server.
Shows the time elapsed since last time the print server was restarted.
Shown for multifunctional Canon devices which have scanning
capabilities. If the scanner is in use, the status will change from Idle to
Busy and the User name will be shown.
45
Print Server Management and Configuration
Network Settings
Changing Network Settings
Support
Troubleshoot and Upgrade
Server Report
To change the print server’s network settings, select Admin | Network
Settings | Detailed View. For additional information, see “Setting Network
Protocol Parameters” on page 49.
From the Support page you can receive help to resolve any installation or
print problems that might occur. If your problems persist, the Support
page allows you to produce a Server Report. The Server Report includes
the settings of the AXIS 1650, information about your connected printer
as well as the current network settings. The Server Report is of great value
for support assistance, so please mail, email or fax it to your support
channel together with a detailed problem description.
If you cannot successfully install your print server, please try the
troubleshooting instructions to solve your installation problems. The
troubleshooter is started by clicking the Troubleshooting steps link. If
you still cannot print satisfactorily after performing the troubleshooting
instructions, please produce a Server Report and contact your local
supplier.
A Server Report is a document containing technical information about
your print server and the connected printer. This report is of great value
for support assistance, so please produce a Server Report and mail, email
or fax it to your support channel together with a detailed problem
description. Click the Server Report link to prepare your Server Report
and problem description to Axis Communications Support team:
You must have an e-mail account and an e-mail program set up on your
computer. It is also important that you include the entire Web page in the
mail and not just a link to the page.
AXIS Online Services
Click the print server product page to receive information about your
print server model. The product page, available on the Axis Web Site,
offers you up-to-date information, print server manuals, FAQs, software
updates and technical support, etc.
Contact Information
If you need to contact any Axis distributor or local office, please click the
Axis distributor or office link.
Statistics
The Statistics page displays information about the network traffic to and
from the AXIS 1650 as well as information about servers and services
that are connected or associated with the AXIS 1650.
Network Statistics
Network Connections
46
From the Network Settings page you can set all parameters that control
the network traffic to and from the AXIS 1650. You can enable or disable
any of the supported network protocols and fine-tune the parameters.
Click the Network Statistics icon to display a list of statistical
information about the data traffic to and from the print server.
Click the Network Connections icon to display a list of servers and
network services that currently are connected to the print server and the
status of each connection.
AXIS 1650 User’s Manual
Print Server Management and Configuration
Setting General Parameters
To change the print server’s general parameters, select Admin | General
Settings => Change in the Web interface.
Note: All print server settings have default values that have been
carefully selected by Axis. In most instances, there is no need to change
the default values. Observe that all network configuration should involve
the Network Administrator.
Print Server Name
System Name
This name identifies the print server to the users and will be part of the
default name of the connected printer and printer queue name. The
default name is AXISXXXXXX, where XXXXXX are the last six digits of
the print server serial number.
Example: If the serial number is 00 40 8c 18 16 36, the default print
server name is AXIS181636.
This name identifies the network printer to the users.
Default = <blank>
System Location
This parameter allows you to specify where the network printer is located
in your organization. This enables you to find the device you are working
with.
Default = <blank>
System Contact
Enter the name of e.g. the System Manager.
Default = <blank>
System Contact Phone Nbr.
System Comment
Enter the telephone number of e.g. the System Manager.
Default = <blank>
Enter comments regarding the network printer.
Default = <blank>
Language
Select the language to be displayed in the print server’s embedded Web
pages: English or Japanese.
Root Password
Enter a password in the field. Up to 15 alphanumeric characters can be
entered.
Default = <blank>
Network Speed
Set your network speed: 10_HALF_DX, 10_FULL_DX, 100_HALF_DX,
100_FULL_DX or let the print server sense the correct speed
(AUTO_SENSE).
Default = AUTO_SENSE
SNMP Enabled
Select Yes to permit access using the SNMP protocol, select No to reject
access using the SNMP protocol.
Default = Yes
Community Name
AXIS 1650 User’s Manual
Specify the community name for SNMP. Up to 32 alphanumeric
characters can be entered.
Default = public
47
Print Server Management and Configuration
Setting Restrictions
To change print server permissions and restrictions, select Admin |
General Settings => Change and select the Restrictions tab in the Web
interface.
TCP Restriction Enabled
When set to Yes, users specified in the IP Address List are rejected or
accepted (depending on how the TCP Restriction Mode is set), to send
print jobs over the print server.
Default = No
TCP Restriction Mode
When set to Accept, users specified in the TCP Restriction IP Address List
are allowed to use this print server.
When set to Reject, users specified in the TCP Restriction IP Address List
are not allowed to use this print server.
Default = Accept
TCP Restriction IP Address
List
Here you specify the users which are allowed (or not allowed, depending
on how TCP Restriction Mode is set) to use the print server. IP addresses
or ranges of IP addresses can be specified:
Example IP addresses: 10.13.16.150, 10.13.16.151
Example IP address range: 10.13.16.160-0.13.16.170
Default = <blank>
Note: If your print server is connected to a CAPT 1.0 printer you will
receive an error message stating Network Error if you are not allowed to
print with this print server
SNMP Restriction Enabled
SNMP Restriction Mode
48
When set to Yes, users specified in the SNMP Restriction IP Address List
are rejected or accepted (depending on how the SNMP Restriction mode is
set).
Default = No
When set to Accept, only users specified in the SNMP Restriction IP
Address List are permitted to specify/browse the settings for the device
using the SNMP protocol.
When set to Reject, only users specified in the SNMP Restriction IP
Address List are rejected from specifying/browsing the settings for the
device using the SNMP protocol.
Default = Accept
SNMP Restriction IP
Address List
Users specified here are rejected or accepted. IP addresses or ranges of IP
addresses can be specified as follows:
Example IP addresses: 10.13.16.150, 10.13.16.151
Example IP address range: 10.13.16.160-10.13.16.170
Default = <blank>
SLP Restriction Enabled
When set to Yes, users specified in SLP Restriction IP Address List are
rejected or accepted (depending on how the SLP Restriction Mode is set).
Default = No
SLP Restriction Mode
When set to Accept, only users specified in the SLP Restriction IP Address
List are permitted to specify/browse the settings for the device using the
SLP protocol.
When set to Reject, only users specified in the SLP Restriction IP Address
List are rejected from specifying/browsing the settings for the device
AXIS 1650 User’s Manual
Print Server Management and Configuration
using the SLP protocol.
Default = Accept
SLP Restriction IP Address
List
Users specified here are rejected or accepted.IP addresses or ranges of IP
addresses can be specified as follows:
Example IP addresses: 10.13.16.150, 10.13.16.151
Example IP address range: 10.13.16.160-10.13.16.170
Default = <blank>
Setting Network Protocol Parameters
To change the print server’s network settings, select Admin | Network
Settings | Detailed View in the Web interface.
Frame Type
LPD Banner Page Mode
AXIS 1650 uses frame type Ethernet II for network packages.
Check the appropriate box to specify if the LPD banner page is to be
printed.
Off disables the LPD banner page.
Auto prints the LPD banner page first or last depending on your operating
system.
Last forces the printer to print the LPD banner page last, independently of
operating system.
Default value = Off
Note: LPD Banner Page Mode is not available for Canon printers
supporting Canon Advanced Printing Technology or Canon Advanced
Raster Printing System.
IP Address
Specify the IP address of your print server in the format w.x.y.z. You
should acquire a unique and unused IP address from your Network
Administrator in order to prevent conflicts with other network devices.
Default value = 192.168.0.90
Note: If DHCP, BOOTP or RARP is enabled, your manual settings might be
overridden when you restart the print server. To make sure that this will
not happen, you are advised to disable BOOTP and RARP when you are
setting the IP address manually, DHCP is disabled by default.
Important: If you change the IP address you will lose contact with the
print server. You must enter the new IP address of the print server in the
address/location field of your Web browser to continue to configure and
manage the print server via the Web browser.
Subnet Mask
Specify the subnet mask used for determining when the traffic should be
sent via a router. This number, in combination with the IP address,
identifies on which network the print server is located. The normal class C
subnet mask value is usually 255.255.255.0.
Default value: 0.0.0.0, indicates that all network segments are accessible.
Default Router
Specify the IP address of the default router. All traffic directed outside the
local network, defined by the subnet mask, is sent to the default router.
Any re-routing via other routers is done automatically. The setting 0.0.0.0
indicates that no default router is set. If that is the case, the print server
AXIS 1650 User’s Manual
49
Print Server Management and Configuration
anticipates that there is a router available that automatically senses and
redirects the print server's packets to destinations outside the local
network segment.
Default value: 0.0.0.0
DHCP Enabled
Set to Yes to enable DHCP (Dynamic Host Configuration Protocol). DHCP
automatically downloads the IP address to each print server at startup.
Depending on how your network has been configured, other Internet
related parameters (such as the default router, subnet mask, etc.) might
also be set automatically. It is recommended that you verify the settings
when the server has been restarted and then enter any missing parameters
manually.
Default value = No (disabled)
BOOTP Enabled
Set to Yes to enable BOOTP (BOOTstrap Protocol). BOOTP downloads the
IP address to each print server at startup. Depending on how your
network has been configured, other Internet related parameters (such as
the default router, subnet mask, etc.) might also be set automatically.
However, we recommend that you verify the settings when the server has
been restarted and then enter any missing parameters manually.
Default value = No (disabled)
RARP Enabled
Set to Yes to enable RARP (Reverse Address Resolution Protocol). RARP
downloads the IP address to each print server at startup. This method only
operates over single network segments. Other Internet related parameters
(such as the default router, subnet mask, etc.) must be entered manually
as RARP only sets the IP address.
Default value = No (disabled)
DNS Server Address
DNS Dynamic Update
DNS Host name
Select Yes to enable DNS (Domain Name Server). DNS uses NetBIOS
names to allow clients to locate resources on TCP/IP networks.
Default value = No
Specify DNS Host name. This name will be used in all environments as
the identifier of this print server.
Default value = <blank>
DNS Domain Name
Specify the name of the domain to which the print server belongs.
Domain refers to a set of computers on a network that have been assigned
a common name. A domain might contain several workgroups.
Default = <blank>
WINS Enabled
Select Yes to enable WINS (Windows Internet Name Service) over TCP/IP.
WINS uses NetBIOS names to allow Windows based clients to locate
resources on TCP/IP networks.
Default value = Yes
WINS Server Address
WINS Host Name
50
Specify the IP address of the DNS (Domain Name Server). DNS uses
NetBIOS names to allow clients to locate resources on TCP/IP networks.
Default = 0.0.0.0
Specify the IP address of the primary WINS server. The WINS server is
used for identifying a computers by its host name instead of by its IP
address.
Default value = 0.0.0.0
Specify the WINS host name, which will be used as the identifier of your
AXIS 1650 User’s Manual
Print Server Management and Configuration
print server.
Default = <blank>
Scope ID
SNTP Server Address
SNTP Update Interval
Specify the NetBIOS scope to which the print server belongs. The scope ID
is a character string value that is appended to the NetBIOS name and used
for all NBT communication. The scope ID defines a group of computers
that recognizes a registered NetBIOS name and all NetBIOS traffic will be
confined within this group.
Default value = <empty> which specifies the default scope.
Specify the Time server’s IP address or network name.
Default = <blank>
The interval between requests to the Time Server for a time update.
Default = 1hours
Time Zone
Specify the time zone for your print server location. Note: This setting is
only visible in the English firmware version.
Default = GMT
Daylight Saving
Set to Yes if you have Daylight saving. Note: This setting is only visible in
the English firmware version.
Default = No
SLP Enabled
SLP Scope List
Unicast Communications
Mode
AXIS 1650 User’s Manual
Set to Yes to enable SLP communication to and from the print server.
Default = Yes
Specify the name of the SLP scope to which the print server belongs. The
scope refers to a set of computers on a network that have been assigned a
scope name.
Default = DEFAULT
Set to Yes to enable the Unicast Communications Mode.
Note that this setting only appears when you are using a CAPT capable
printer. See “Enabling Unicast Network Communication” on page 64 for
additional information.
Default = No
51
Print Server Management and Configuration
Print Server Management Using FTP
Having assigned an IP address to your AXIS 1650, as described in “Set
the IP Address” on page 11, you can change the AXIS 1650 parameter
settings using the File Transport Protocol (FTP).
Editing the config file
Follow the instructions below to edit the config file using FTP:
1. Log in to the AXIS 1650 by typing:
ftp <IP address> or ftp <host name> in a Command prompt.
2. Enter the user id (the default entry is root; if the default password has been
changed then it must also be entered).
3. Download the config file to your host by typing:
get config
4. Edit the file using your preferred text editor.
5. Save the config file to the AXIS 1650 by typing:
put config CONFIG
It is important that the destination file is specified in capital letters.
Otherwise the edits are temporary and will be lost once the AXIS 1650 has
been rebooted.
Example
How to get and put the config file using FTP from a Command prompt.
> ftp npserver
connected to npserver.
220 AXIS 1650 FTP Print Server v1. June 1 2005 ready.
Name (npserver:thomas): root
FTP Help
By typing
in step 3 in the FTP instructions described above, a list of
available commands will be displayed.
52
AXIS 1650 User’s Manual
help
Print Server Management and Configuration
Print Server Management Using SNMP
You can use SNMP (Simple Network Management Protocol) to monitor
and configure the AXIS 1650 remotely. All major functions for print
servers are supported.
General Information
SNMP refers to a set of standards for network management, including a
protocol, a database structure specification, and a set of data objects. The
AXIS 1650 SNMP implementation runs in TCP/IP networks.
The management is handled by NMS (Network Management System)
software running on a host on your network. The NMS software
communicates with network devices by the means of messages, which are
references to one or more objects.
A message can be a question or an instruction to a device, or an alarm
triggered by a specific event in a device. Objects are contained in MIBs
(Management Information Base), where MIB-II is a standard database.
The AXIS 1650 supports the following MIBs:
•
•
•
•
AXIS 1650 User’s Manual
relevant parts of MIB-II
relevant parts of the Host Resource MIB
relevant parts of the Printer MIB
relevant parts of the CANON-MIB
53
Scanning with AXIS 1650
Section 9
Scanning with AXIS 1650
If your Canon device also functions as a scanner, you can use your AXIS
1650 as a scanner server, too.
This section describes how to scan via an AXIS 1650 using AXIS
ScanClient. For general information on scanning, see your Canon device
manual. The examples here show Windows XP and a Canon MF3110 with
MF Toolbox 4.7.
Before continuing with this section, see to it that you have a working
printing environment and the scanning software for the Canon device
installed (see your Canon device manual as well as the previous sections
of this Manual).
AXIS 1650 gives you a choice between two scanning methods:
•
Scanning invoked from your computer - see page 56.
•
Scanning invoked from the Canon device - see page 60.
Both methods need AXIS ScanClient installed on the client computer.
AXIS ScanClient will open a channel between your computer and the
scanner. The channel will be open for five minutes to give you time to
walk to the scanner and place the object to be scanned on the flatbed.
During these five minutes you have exclusive rights to the scanner (but
print jobs function as usual).
Installing AXIS ScanClient
Locate AXISScanClient_SetUp.exe on the AXIS 1650 CD or on
www.axis.com.
1. Start the SetUp program by double-clicking its icon.
2. Select installation language and click [OK].
54
AXIS 1650 User’s Manual
Scanning with AXIS 1650
3. Installation is about to begin. Click [Next].
4. Read and accept the License Agreement. Click [Next].
5. Select Destination Location (default location is C:\Program Files\AXIS
Communications\AXIS ScanClient). Click [Next].
6. Select Start Menu Folder (default folder is AXIS ScanClient). Click [Next].
7. Check the values and click [Install] to start the installation process.
8. After a short while AXIS ScanClient has been installed on your computer.
Click [Finish] to complete the installation.
AXIS 1650 User’s Manual
55
Scanning with AXIS 1650
Using AXIS ScanClient
Connect to the
Scanner
1. Start AXIS ScanClient (Start | AXIS ScanClient). The client will search the
network for scanning devices. Mark the one you would like to use by
clicking on it in the list (you can also select a scanner by entering its IP
address). Click [Connect].
2. If the scanner is busy AXIS ScanClient will show who is using it, otherwise
you will be connected, as indicated on the message line.
Click [Help] to get information on how to connect and disconnect.
Disconnect from the
Scanner
You end a scanning session by clicking [Disconnect] on the AXIS
ScanClient.
The message line will change to Disconnected.
Note:
The scanning session will automatically end and the channel will be
disconnected after 5 minutes of inactivity.
Invoking a Scan from your Computer
Start a Scan from
your Computer
56
Connect to the scanner with AXIS ScanClient - see page 56 - and place
the object to be scanned on the scanner flatbed.
AXIS 1650 User’s Manual
Scanning with AXIS 1650
1. On your computer, start the receiving program (e.g. Canon MF Toolbox —
Scan Function). Click [Save] to open the Save dialog.
2. In the Save dialog, click [Start] to start scanning.
3. When ready, close the Save dialog and the Canon MF Toolbox.
4. Disconnect from the scanner - see page 56, and remove the scanned object
from the flatbed.
Scanning from Other
Programs
Example 1
Using the method described above, you can scan from many kinds of
image software, for instance Microsoft’s Scanner and Camera Wizard,
Adobe Photoshop, Gimp, Adobe Acrobat and others that can use TWAIN
or WIA drivers.
Example using Microsoft’s Scanner and Camera Wizard:
1. Connect to the scanner with AXIS ScanClient - see page 56 - and place
the object to be scanned on the scanner flatbed.
2. Go to Start | Printers and Faxes.
3. Click on Scanners and Cameras.
AXIS 1650 User’s Manual
57
Scanning with AXIS 1650
4. Right-click the device you would like to use (example: WIA Canon MF3110)
and select Get picture using Scanner Wizard.
5. The Scanner and Camera Wizard starts. Click [Next].
6. Select scanning parameters and start scanning.
7. When scanning is ready, disconnect from the scanner - see page 56 and
remove the scanned object from the flatbed.
Example 2
Example using Gimp:
1. Connect to the scanner with AXIS ScanClient - see page 56 and place the
object to be scanned on the scanner flatbed.
2. Start Gimp.
58
AXIS 1650 User’s Manual
Scanning with AXIS 1650
3. Select File | Acquire | TWAIN...
4. Select source (e.g. MF3110).
5. Select scanning parameters and start scanning.
6. When scanning is ready, disconnect from the scanner - see page 56 and
remove the scanned object from the flatbed.
Invoking a Scan from the Canon Device
First time only:
Prepare your
Computer
These five steps are just needed prior to the first scanning invoked from
the Canon device to a certain client computer. By setting these
parameters, the scanning software will be able to work automatically.
1. Connect to the scanner with AXIS ScanClient - see page 56.
2. Go to Start | Printers and Faxes.
3. Click on Scanners and Cameras.
4. Right-click the device you would like to use (example: WIA Canon MF3110)
and select Properties.
AXIS 1650 User’s Manual
59
Scanning with AXIS 1650
5. Select Events and select the event Canon MF3110 Scan Button.
Under Actions, select the option Start this program and select MF ToolBox
Ver4.7 in the list.
Click [OK].
Now you have prepared your computer to automatically take care of
scannings invoked from the Canon device.
Start a Scan from the
Canon Device
Connect to the scanner with AXIS ScanClient - see page 56 and place the
object to be scanned on the scanner flatbed.
1. If the Canon device is in Energy Save mode, press its [Energy Saver key].
2. Press [Scan] on the Canon device.
3. Press [Start] on the Canon device.
4. The Canon device will start to scan.
5. When ready, remove the scanned object from the flatbed and walk back to
your computer.
6. Close the receiving program on your computer and disconnect from the
scanner - see page 56.
Note:
60
When waking up from Power Off or Energy Save mode the Canon device
needs some time (from 30 seconds to a few minutes) to adjust the light
and the scanner to produce optimum scans. Press [Start] repeatedly until
scanning starts.
AXIS 1650 User’s Manual
The Test Button
Section 10
Factory Default
The Test Button
The test button is located on the front right hand side of the print server
and is used to perform a Factory Default:
1. Remove the power adapter to switch off the print server.
2. Press and hold down the test button, while you reconnect the power
adapter.
3. Continue to hold down the test button until the network indicator
remains constantly lit. This should take about 20 seconds.
4. Restart the print server by disconnecting and reconnecting the power
adapter.
Important:
•
•
Canon BubbleJet
Printers
If the AXIS 1650 is connected to a Canon BubbleJet printer, the test
button can be used for the following operations:
•
•
AXIS 1650 User’s Manual
A factory default will reset all print server parameters and settings to
their default values except Node address (NODE_ADDR.)
The IP address (INT_ADDR.) will be reset to default 192.168.0.90
Print a Test Page
Press the test button once to print a test page. The test page contains
basic information about the print server. It is recommended that you
print a test page every time you connect the print server to a printer
Perform a Factory Default
See description above.
61
Upgrading the Firmware
Section 11
Upgrading the Firmware
The print server’s firmware is stored in its Flash memory. This memory
retains its data content even after the power is removed. Flash memory
allows data to be erased and re-written, which is why you can install
firmware updates in your print server as they become available, without
having to replace any parts. New firmware can simply be loaded into the
AXIS 1650 over the network.
Firmware is internal print server software that determines its
functionality.
You can obtain all print server firmware free of charge from the following
locations:
•
•
www.axis.com
your local dealer
Caution!
•
•
Upgrading using FTP
Be careful not to interrupt the file transfer. If the transfer is
interrupted, the print server may have to be re-initialized by your
dealer.
Before upgrading the print server, ensure that it is not printing jobs.
You have to wait until the print job is finished before you can proceed.
•
To upgrade over the network using FTP you will need a file with the
new print server firmware. The name of this file is in the form
1650_x_xx.bin.
• The print server must have a valid IP address.
This example uses these sample values:
Print server model: AXIS 1650
IP address of print server: 10.13.4.105
New firmware version name: 1650_2_00.bin
Location of firmware and upgrade procedure: C:\Axis
(Create a new directory named e.g. ‘Axis’ on your hard drive and
download the firmware to that location).
1. From www.axis.com/techsup/firmware, download the firmware and save
it to a new directory on your computer, e.g. C:\ Axis
2. Open a command prompt from Start => Run. Type cmd in the Run Window
and click OK.
3. The DOS Command Prompt window will open. Make sure you are working
from the c: directory (type c: and press Enter).
4. Type cd Axis
62
AXIS 1650 User’s Manual
Upgrading the Firmware
5. Type dir and press Enter. The Axis directory you have created will display a
list of all files.
6. Connect to the print server using ftp: Type ftp 10.13.4.105 (this example
uses print server IP address 10.13.4.105)
7. Enter the user name, the default user is root (if the default password has
been changed then it must also be entered). Press Enter.
8. Change to binary transfer mode: type bin and press Enter.
9. Type hash and press Enter.
10. Use the 'put' command to upload the upgrade file to the flash location:
Type put 1650_2_00.bin FLASH. A stream of hash marks will appear.
11. You will receive a message stating "Transfer complete. Flash programming
finished OK. "
12. The print server will restart in five seconds running the new software.
13. When you see a new ftp prompt the procedure has successfully been
completed.
Notes:
•
•
•
AXIS 1650 User’s Manual
If the upgrading process fails, just repeat the instructions presented
above.
If you lose contact with the AXIS 1650 after an upgrading failure, just
restart the AXIS 1650 to restore contact.
If the network LED flashes at regular half second intervals, the AXIS 1650
cannot process any print jobs. In order to leave this state, you must
repeat the instructions above.
63
Enabling Unicast Network Communication
Section 12
Enabling Unicast Network Communication
Important: All network configuration must be performed by the network
administrator!
AXIS CAPT Print Monitor uses broadcast communication, so that status
information from the print server can be shared between several users
without elevating network traffic.
Broadcast communication is used by default in the print server.
In some networks where broadcast communication isn’t preferred, unicast
communication can be used, which will also increase the network load.
To enable unicast communication, some settings must be configured in
the AXIS 1650 and in the AXIS CAPT Print Monitor during the software
installation.
Enable Unicast via the
Web Interface
Using firmware 2.00 or later you can use your browser to enable unicast
network communication. Open the Web interface of the print server.
Select Admin | Network Settings | Detailed View. The TCP/IP tab will
open. Under CAPT Port Settings, set Unicast Communications Mode to
Yes. Click OK to save the setting.
Go on to Install the AXIS CAPT Print Monitor on page 66.
Enable Unicast using
FTP
Follow these steps to enable unicast network communication using FTP:
1. Open a command prompt and change to a directory where you can store
the configuration file by typing C:/<any directory> and press Enter.
2. Log in to the AXIS 1650 with the command:
ftp <IP address>
where <IP address> is the IP address of your AXIS 1650.
3. You will be prompted for a user id:
default user id = root (if the default password has been changed then it must
also be entered)
4. To access the configuration file, type: get config
5. Next go to the C: directory on your computer and locate the file named
config.
6. Open the config file using any text editor.
64
AXIS 1650 User’s Manual
Enabling Unicast Network Communication
7. Locate the parameter named USE_IP_PORT_NAME:
type YES
Make sure this parameter is set to YES.
8. Once the editing is complete, save the file as config
9. In the Command prompt window, upload the configuration file to the AXIS
1650 by typing
put config CONFIG
10. To exit FTP, type
quit
Note: This will also change the Print Server Name parameter so that
it is based on the print server’s IP address, with “_” replacing the “.”
in the address.
Example: If the print server’s IP address is 192.168.3.191 the Print
Server Name parameter will be changed to 192_168_3_191.
It is important that the destination file is specified in capital letters.
Otherwise the edits are temporary and will be lost once the AXIS 1650 has
been rebooted.
Go on to Install the AXIS CAPT Print Monitor on page 66.
AXIS 1650 User’s Manual
65
Enabling Unicast Network Communication
Install AXIS CAPT Print
Monitor
1. Install AXIS CAPT Print Monitor software on your workstation. The
software is available on the AXIS 1650 CD and on www.axis.com. Click
your way through the program.
2. During the software setup, you will reach the Set the Unicast
Communication Mode screen, check the Enable unicast check-box.
3. Click Next and Finish to finish the installation.
4. Windows XP/Server 2003:
Go to Start | Printers and Faxes and click the Add a Printer icon to start
the Add Printer Wizard.
(Windows XP Home Edition: Start | Control Panel | Printers and Faxes | Add
a Printer).
Click Next.
Windows 2000:
Go to Start | Settings | Printers and click the Add Printer icon to
start the Add Printer Wizard. Click Next.
5. Select Local Printer attached to this computer. Make sure the
Automatically detect and install my Plug and Play printer check box is not
checked. Click Next.
6. Click the Create a new port radio button and select AXIS CAPT Port. Click
Next.
66
AXIS 1650 User’s Manual
Enabling Unicast Network Communication
7. A pop-up window will appear. Enter the IP address of the AXIS 1650.
8. Select Manufacturer and Printer from the driver list. Click Next.
9. Choose whether you want to keep the existing driver or to replace it. If you
already have the printer’s driver installed, you will be asked whether to keep
it or to replace it.
10. Click Next. Supply a name for the printer and choose whether you want to
make it your default printer. Click Next.
11. Choose whether you want to share the printer with other network users,
print a test page, etc. Select the appropriate radio button and click Next and
Finish.
12. Print a test page to verify. You have now completed the installation.
AXIS 1650 User’s Manual
67
Internet Connection Firewall in Windows XP SP2
Section 13
Internet Connection Firewall in Windows XP
SP2
If you have upgraded to Windows XP SP2, you need to open UDP port
10260 in the Internet Connection Firewall when using Broadcast
communication. For Unicast comunication, the firewall can remain
closed.
UDP port 10260 is opened automatically in Internet Connection
Firewall, if allowed during the installation of AXIS CAPT Print Monitor
in Windows XP/2003, see “Windows Installation” on page 17.
To open the Internet Connection Firewall:
1. Go to Start | Control Panel | Security Center.
2. Select Firewall:
3. Make sure On is selected.
“Don’t allow exceptions” and “Off” must be unchecked!
68
AXIS 1650 User’s Manual
Internet Connection Firewall in Windows XP SP2
4. Click Exceptions and highlight AXIS CAPT Port.
5. Click OK.
Note: If you accidentally delete the AXIS CAPT Port and want to recreate
it, go to Exceptions | Add Port and configure the port.
AXIS 1650 User’s Manual
69
Technical Specifications
Section 14
Supported Devices
Technical Specifications
AXIS 1650 is developed to network Canon printers and multifunctional
products. If your Canon device also functions as a scanner, you can use
your AXIS 1650 as a scanner server, too.
AXIS 1650 supports Canon Advanced Printing Technology, Canon
Advanced Raster Printing System as well as Canon BubbleJet printers.
Important: AXIS 1650 does not support devices from other
manufacturers than Canon.
Supported Systems
Microsoft Windows
Windows 98, Windows 2000, Windows Me, Windows XP, Windows
Server 2003.
Print Methods: LPR, Raw TCP, CAPT over TCP/IP in Microsoft Windows.
Novell NetWare
WWW
Supported Protocols
TCP/IP
Network Management
Supported Languages
Logical Connection
Wired Network
Attachments
Printer Ports
6.X. NDPS supported over IP. Support for iPrint using IPP protocol.
Netscape Communicator 4.7 and above, Internet Explorer 4.0 and above.
Windows TCP/IP, WINS.
LPD, FTP, BOOTP, ARP, RARP, DHCP, ICMP, IGMP, IP, TCP, UDP, HTTP,
SLP, SNMP, Raw TCP, DNS, DDNS.
Print server/job/printer status presentation and management via standard
Web browser or ftp.
English and Japanese.
Supports NWay that provides auto-detection of network speed.
Use Ethernet II frame type, full duplex.
RJ-45 connector (Category 5 shielded twisted pair cable) for 10baseT
Ethernet or 100base TX Fast Ethernet.
•
•
70
One Low- and Full-Speed USB 1.1 port, and works with USB v 2.0
(Low-Speed and Full-Speed).
The USB cable shipped with the product supports Low-Speed and FullSpeed. Hi-Speed is not supported.
One high-speed IEEE 1284 compatible parallel port.
AXIS 1650 User’s Manual
Technical Specifications
Power Consumption
Dimensions
Maximum 5.6 W.
Power provided by Power Adapter type PS-H: 5.1V DC 2000 mA
Height x Width x Depth
1.1in (29 mm), 2.4in (62 mm), 4.6in (117 mm)
Weight
0.18lb (81g)
Environmental
Temperature
40 - 105 °F (5 - 40 °C)
Approvals
EMC
Safety
Hardware
Front Panel
EN 55 024:1998
EN 55 022:1998 + A1 (CISPR 22:1997 + A1) Class B
EN 61000-3-2:2000
EN 61000-3-3:1995+A1
VCCI:2002 Class B ITE (CISPR 22:1997 + A1:2000, Class B
C-tick AS/NZS 3548
FCC part 15, subpart B, Class B, demonstrated by compliance with EN
55022:1998 (CISPR 22:1997) Class B.
EN 60950, approved power supplies for all countries.
32-bit 100 MHz AXIS ETRAX 100LX RISC Controller, 2 MB Flash
memory, 8 MB RAM.
2 LED indicators for Power and Network.
Test button for performing Factory Default
All specifications are subject to change without prior notice.
AXIS 1650 User’s Manual
71
Index
Index
A
Adhesive Clip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Adhesive Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Admin mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
AXIS CAPT Print Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
AXIS Online Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
AXIS ScanClient . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
B
Broadcast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Broker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 34
BSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
C
Canon Advanced Printing Technology . . . . . . . . . . . . . . . . 1, 7, 42, 45, 49
Canon Advanced Raster Printing System . . . . . . . . . . . . . . 1, 7, 42, 45, 70
Canon BubbleJet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 61, 70
Changing General Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Changing Network Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Changing Permissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Community Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Configuration methods
FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Web browser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Configure Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Contact Informatio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
D
Daylight Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
default IP address 192.168.0.90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
default values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DHCP scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
12
47
16
F
Factory Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44, 61
firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
firmware version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Flash memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
FTP Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
72
AXIS 1650 User’s Manual
Index
H
Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Host Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 16
I
IEEE 1284 parallel port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 70
Installing Printer Ports
Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17, 22
Windows 2000, XP, 2003 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Windows 98, Me . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Internet Connection Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
IP Address
Automatic Assignment Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Manual Assignment Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Setting, using ARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Setting, using AXIS IP JumpStarter . . . . . . . . . . . . . . . . . . . . . . . . . . 11
L
Label, backside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
License Agreement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LPD Banner Page Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LPR Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
47
18
23
49
27
N
NetWare
Browse for a Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30, 35
Check Printer Health . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31, 36
Container name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29, 34
Create a Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29, 34
Enable IPP Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Enable iPrint Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
iManager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 34
Installing Printer Locally . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33, 38, 39
iPrint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
iPrint Map Designer tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32, 37
Make the Printer Available . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32, 37
Manage Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30, 35
NDPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 34
Novell gateway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Novell LPR Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Select Default Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30, 35
Setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Network Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42, 45
Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Network Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
AXIS 1650 User’s Manual
73
Index
Network Statistic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
P
Parameter List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
peer-to-peer printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Print Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43, 45
Print Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Print Server Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 42, 44, 47
Print Server Uptime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43, 45
Print Service Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Printer Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Printer Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42, 45
Printer Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42, 45
Q
Queue Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
R
Remote Printer Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Root Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
S
Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Scanner status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43, 45
Scanning
Invoked from Canon device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Invoked from computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Scanning with AXIS 1650 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42, 44
Services Available from the Admin Mode . . . . . . . . . . . . . . . . . . . . . . . . 44
Services Available from the User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Setting General Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Setting Network Protocol Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Setting Restriction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Setting the Internet address
ARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Setting up
NetWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setup using NetWare 6.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Setup using NetWare 6.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
SLP Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
SLP Restriction Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SLP restriction enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SLP restriction IP address list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
SLP restriction mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SLP Scope List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
74
AXIS 1650 User’s Manual
Index
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
SNMP access enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
SNMP Restriction Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SNMP restriction IP address list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SNMP restriction mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SNTP Server Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
SNTP update interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Software Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 46
Supported Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Supported Printers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
System Comment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
System Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
System Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42, 44, 47
System Manager Telephone Nbr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
System Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
T
TCP restriction enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
TCP restriction IP address list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
TCP restriction mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Technical Assistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Test Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Test Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
This Print Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44, 45
Time Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Two connected printers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
U
UDP port 10260 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Unicast Communications Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51, 64
UNIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
User mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
V
View Job Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43, 45
W
Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
WINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Z
z (Queue Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
AXIS 1650 User’s Manual
75
Download PDF

advertising