Canon CP910/BLK All in One Printer User Manual

DV260.book 1 ページ 2003年1月28日 火曜日 午後7時20分
DVD Player
DV-266-S
DV-366-S
DV-366-K
DV-466-S
DV-466-K
Operating Instructions
DV260.book 2 ページ 2003年1月28日 火曜日 午後7時20分
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
[Taiwanese model]
The lightning flash with arrowhead
symbol, within an equilateral
triangle, is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product's enclosure that may be of
sufficient magnitude to constitute
a risk of electric shock to persons.
CAUTION:
TO PREVENT THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO
USER-SERVICEABLE
PARTS
INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important
operating
and
maintenance
(servicing)
instructions in the literature
accompanying the appliance.
H002_En
WARNING: The apparatus is not waterproofs,
to prevent fire or shocks hazard, do not
expose this apparatus to rain or moisture and do
not put any water source near this
apparatus, such as vase, flower pot, cosmetics
container and medicine bottle etc.
H001A_En
CAUTION
WARNING: BEFORE PLUGGING IN THE UNIT
FOR THE FIRST TIME, READ THE FOLLOWING
SECTION CAREFULLY. THE VOLTAGE OF THE
AVAILABLE POWER SUPPLY DIFFERS
ACCORDING TO COUNTRY OR REGION. BE SURE
THAT THE POWER SUPPLY VOLTAGE OF THE
AREA WHERE THIS UNIT WILL BE USED MEETS
THE REQUIRED VOLTAGE (E.G., 230V OR 120V)
WRITTEN ON THE REAR PANEL.
H041A_En
This product contains a laser diode of higher class
than 1. To ensure continued safety, do not remove
any covers or attempt to gain access to the inside
of the product.
Refer all servicing to qualified personnel.
The following caution label appears on your unit.
Location: rear of the unit
WARNING: NO NAKED FLAME SOURCES,
SUCH AS LIGHTED CANDLE, SHOULD BE
PLACED ON THE APPARATUS. IF NAKED FLAME
SOURCES ACCIDENTALLY FALL DOWN, FIRE
SPREAD OVER THE APPARATUS THEN MAY
CAUSE FIRE.
H044_En
[Central and South American model model]
On the top of the player
[Expect PX model]
[Except PX and Taiwanese model]
H018A_En
When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction’s rules that apply in your country
or area.
H048 En
DV260.book 3 ページ 2003年1月28日 火曜日 午後7時20分
[For Australian model]
ENERGY STAR® and the
ENERGY STAR
certification mark are
registered US marks.
K001C_En
[For PX model]
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/
TV technician for help.
H010_En
Information to User
Alteration or modifications carried out without
appropriate authorization may invalidate the
user's right to operate the equipment. H011_En
CAUTION:
This product satisfies FCC regulations when
shielded cables and connectors are used to
connect the unit to other equipment. To
prevent electromagnetic interference with
electric appliances such as radios and
televisions, use shielded cables and connectors for connections.
H012_En
CAUTION
• Use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous
radiation exposure.
• The use of optical instruments with this
product will increase eye hazard.
H013_En
Operating Environment H045_En
Operating environment temperature and
humidity:
+5ºC – +35ºC (+41ºF – +95ºF); less than 85%RH
(cooling vents not blocked)
Do not install in the following locations
÷ Location exposed to direct sunlight or strong
÷ artificial light
÷ Location exposed to high humidity, or poorly
ventilated location
WARNING:
Slot and openings in the cabinet are
provided for ventilation and to ensure reliable
operation of the product and to protect it from
overheating, to prevent fire hazard, the openings
should never be blocked and covered with items,
such as newspapers, table-cloths, curtains, etc. Also
do not put the apparatus on the thick carpet, bed,
sofa, or fabric having a thick pile.
H040_En
CAUTION:
THE STANDBY/ON BUTTON IS
SECONDARY CONNECTED AND THEREFORE DOES
NOT SEPARATE THE UNIT FROM MAINS POWER IN
STANDBY POSITION. THEREFORE INSTALL THE
UNIT SUITABLE PLACES EASY TO DISCONNECT
THE MAINS PLUG IN CASE OF THE ACCIDENT. THE
MAINS PLUG OF UNIT SHOULD BE UNPLUGGED
FROM THE WALL SOCKET WHEN LEFT UNUSED
FOR A LONG PERIOD OF TIME.
H017B_En
This product is for general household purposes.
Any failure due to use for other than household
purposes (such as long-term use for business
purposes in a restaurant or use in a car or ship)
and which requires repair will be charged for
even during the warranty period.
K041_En
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of
this copyright protection technology must be
authorized by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
This product includes FontAvenue® fonts
licenced by NEC corporation. FontAvenue is
a registered trademark of NEC Corporation.
DV260.book 4 ページ 2003年1月28日 火曜日 午後7時20分
01
Thank you for buying this Pioneer product.
Please read through these operating instructions so that you will know how to operate your
model properly. After you have finished reading the instructions, put them in a safe place for
future reference.
Contents
01 Before you start
04 Getting started
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
What’s in the box . . . . . . . . . . . . . . . . . . . . 7
Putting the batteries in the remote
control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using the remote control . . . . . . . . . . . . . 7
Disc / content format playback
compatibility . . . . . . . . . . . . . . . . . . . . . . . 8
General disc compatibility . . . . . . . . . . . . 8
CD-R/RW compatibility . . . . . . . . . . . . . . 8
DVD-R/RW compatibility . . . . . . . . . . . . . 8
PC-created disc compatibility . . . . . . . . . 9
About WMA . . . . . . . . . . . . . . . . . . . . . . . 9
Compressed audio compatibility . . . . . . . 9
JPEG file compatibility . . . . . . . . . . . . . . 10
Switching on . . . . . . . . . . . . . . . . . . . . . . . 22
Let’s Get Started . . . . . . . . . . . . . . . . . . . . 22
Using the on-screen displays . . . . . . . . . . . 24
Setting up with the Setup Navigator . . . . .25
Playing discs . . . . . . . . . . . . . . . . . . . . . . . 27
Basic playback controls . . . . . . . . . . . . . 29
Resume and Last Memory . . . . . . . . . . . 30
DVD-Video disc menus . . . . . . . . . . . . . . 30
Video CD/Super VCD PBC menus . . . . . .31
02 Connecting up
Rear panel connections . . . . . . . . . . . . . .
Easy connections . . . . . . . . . . . . . . . . . . .
Connecting using the S-video output . . . .
Connecting using the component video
output . . . . . . . . . . . . . . . . . . . . . . . . . . .
Taiwanese model only: Connecting using
the D1/D2 video output . . . . . . . . . . . . . .
Connecting to an AV receiver . . . . . . . . . .
11
12
13
14
14
15
03 Controls and displays
Front panel . . . . . . . . . . . . . . . . . . . . . . . . 17
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Remote control . . . . . . . . . . . . . . . . . . . . 20
4
En
05 Playing discs
Introduction . . . . . . . . . . . . . . . . . . . . . . . . 32
Using the Disc Navigator to browse the
contents of a disc . . . . . . . . . . . . . . . . . . . 32
Scanning discs . . . . . . . . . . . . . . . . . . . . . 33
Playing in slow motion . . . . . . . . . . . . . . . 34
Frame advance/frame reverse . . . . . . . . . . 34
Looping a section of a disc . . . . . . . . . . . . 34
Using repeat play. . . . . . . . . . . . . . . . . . . . 35
Using random play . . . . . . . . . . . . . . . . . . 36
Creating a program list . . . . . . . . . . . . . . . 37
Editing a program list . . . . . . . . . . . . . . . 39
Other functions available from the
program menu . . . . . . . . . . . . . . . . . . . . 39
Searching a disc . . . . . . . . . . . . . . . . . . . . 40
Switching subtitles . . . . . . . . . . . . . . . . . . 40
Switching DVD audio language . . . . . . . . . 40
Switching VR format DVD-RW audio
channel . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
DV260.book 5 ページ 2003年1月28日 火曜日 午後7時20分
01
Switching audio channel when playing a
Video CD/Super VCD . . . . . . . . . . . . . . . .
Zooming the screen . . . . . . . . . . . . . . . . .
Switching camera angles . . . . . . . . . . . . .
Displaying disc information . . . . . . . . . . .
41
41
42
42
06 Viewing JPEG discs
Viewing JPEG discs . . . . . . . . . . . . . . . . . 44
Using the JPEG Disc Navigator and Photo
Browser . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Zooming the screen . . . . . . . . . . . . . . . . . 45
07 Audio Settings menu
Audio DRC . . . . . . . . . . . . . . . . . . . . . . . . 46
Virtual Surround . . . . . . . . . . . . . . . . . . . . 46
08 Video Adjust menu
Video Adjust . . . . . . . . . . . . . . . . . . . . . . . 48
Creating your own presets . . . . . . . . . . . 48
09 Initial Settings menu
Using the Initial Settings menu . . . . . . . .
Digital Audio Out settings . . . . . . . . . . . .
Digital Out . . . . . . . . . . . . . . . . . . . . . . .
Dolby Digital Out . . . . . . . . . . . . . . . . . .
DTS Out . . . . . . . . . . . . . . . . . . . . . . . . .
96kHz PCM Out . . . . . . . . . . . . . . . . . . .
MPEG Out . . . . . . . . . . . . . . . . . . . . . . .
Video Output settings . . . . . . . . . . . . . . . .
TV Screen . . . . . . . . . . . . . . . . . . . . . . .
Component Out . . . . . . . . . . . . . . . . . . .
S-Video Out . . . . . . . . . . . . . . . . . . . . . .
Language settings . . . . . . . . . . . . . . . . . .
Audio Language . . . . . . . . . . . . . . . . . .
Subtitle Language . . . . . . . . . . . . . . . . .
DVD Menu Language. . . . . . . . . . . . . . .
Subtitle Display . . . . . . . . . . . . . . . . . . .
Display settings . . . . . . . . . . . . . . . . . . . .
OSD Language . . . . . . . . . . . . . . . . . . .
On Screen Display . . . . . . . . . . . . . . . . .
Angle Indicator . . . . . . . . . . . . . . . . . . .
Options . . . . . . . . . . . . . . . . . . . . . . . . . .
50
50
50
51
51
51
51
52
52
52
53
54
54
54
55
55
56
56
56
56
57
Parental Lock . . . . . . . . . . . . . . . . . . . . . 57
PhotoViewer . . . . . . . . . . . . . . . . . . . . . . . 59
010 Additional information
Taking care of your player and discs . . . . . 60
Handling discs . . . . . . . . . . . . . . . . . . . . 60
Storing discs . . . . . . . . . . . . . . . . . . . . . . 60
Discs to avoid . . . . . . . . . . . . . . . . . . . . . 61
Cleaning the unit’s exterior . . . . . . . . . . . 61
Cleaning the pickup lens . . . . . . . . . . . . . 61
Problems with condensation . . . . . . . . . . 61
Hints on installation . . . . . . . . . . . . . . . . 61
Moving the player . . . . . . . . . . . . . . . . . . 62
Power cable caution . . . . . . . . . . . . . . . . 62
Screen sizes and disc formats . . . . . . . . . . 62
Widescreen TV users. . . . . . . . . . . . . . . . 62
Standard TV users . . . . . . . . . . . . . . . . . . 62
Resetting the player. . . . . . . . . . . . . . . . . . 63
Titles, chapters and tracks. . . . . . . . . . . . . 63
DVD-Video regions . . . . . . . . . . . . . . . . . . 64
Selecting languages using the
language code list . . . . . . . . . . . . . . . . . . . 64
Language code list . . . . . . . . . . . . . . . . . . 65
Country code list . . . . . . . . . . . . . . . . . . . . 65
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Setting the TV system . . . . . . . . . . . . . . . . 68
Watching NTSC on a PAL TV
(MOD. PAL) . . . . . . . . . . . . . . . . . . . . . . . . 68
Taiwanese model only: Changing the
on-screen display language to English . . .69
Specifications . . . . . . . . . . . . . . . . . . . . . . 70
5
En
01_before_start.fm 6 ページ 2003年1月30日 木曜日 午前10時28分
01
Before you start
Chapter 1
Before you start
Features
24-bit/192kHz compatible DAC
This player is fully compatible with high
sampling-rate discs, capable of delivering
better-than-CD sound quality in terms of
dynamic range, low-level resolution and highfrequency detail.
Excellent audio performance with
Dolby*1 Digital and DTS*2 software
Logos:
1
When connected to a suitable AV amplifier or
receiver, this player gives great surround
sound with Dolby Digital and DTS discs.
Picture zoom
While a DVD or Video CD/Super VCD is
playing, you can zoom in on any part of the
picture at up to 4x magnification for a closer
look. See Zooming the screen on page 41.
MP3 and WMA compatibility
This player is compatible with CD-R, CD-RW
and CD-ROM discs that contain MP3 or WMA
audio tracks. See also Compressed audio
compatibility on page 9.
Graphical on-screen displays
Setting up and using your DVD player is made
very easy using the graphical on-screen
displays.
Energy saving design
Virtual Dolby Digital using SRS
TruSurround*3
Logo:
SRS TruSurround creates a realistic
surround-sound effect from any Dolby Digital
source using just two speakers. SRS TruSurround is a process approved by Dolby Laboratories for Virtual Dolby Digital sound. See
Virtual Surround on page 46.
This unit is designed to use 0.18 W of power
when in standby mode (except for Taiwan
model: 0.1 W).
PureCinema progressive scan
*2 “DTS” and “DTS Digital Out” are registered
trademarks of Digital Theater Systems, Inc.
When connected to a progressive scancompatible TV or monitor using the component video outputs, you can enjoy extremely
stable, flicker free images, with the same
frame refresh rate as the original movie.
6
En
This player features an auto power-off function. If the player is not used for over 30
minutes, it automatically switches itself into
standby.
*1 Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
*3 TruSurround, SRS and
symbol are
trademarks of SRS Labs, Inc. TruSurround technology is incorporated under license from SRS
Labs, Inc.
DV260.book 7 ページ 2003年1月28日 火曜日 午後7時20分
01
Before you start
What’s in the box
Please confirm that the following accessories
are in the box when you open it.
1 Open the battery compartment cover
on the back of the remote control.
• Remote control
• AA/R6P dry cell batteries x2
• Audio/video cable (red/white/yellow
plugs)
• Power cable (Central and South American model x2)
• Operating instructions x2 (Central and
South American model x3, Australian and
PX model x1)
2 Insert two AA/R6P batteries into the
battery compartment following the indications (, ) inside the compartment.
• Remote control overlay (Taiwanese model
only) — Place the overlay on the remote
control to be able to read the buttons in
Chinese.
Putting the batteries in the
remote control
3
Close the cover.
Incorrect use of batteries can result in
hazards such as leakage and bursting. Please
observe the following:
• Don’t mix new and old batteries together.
• Don’t use different kinds of battery
together—although they may look similar,
different batteries may have different voltages.
• Make sure that the plus and minus ends
of each battery match the indications in
the battery compartment.
• Remove batteries from equipment that
isn’t going to be used for a month or
more.
• When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules
that apply in your country or area.
H048 En
Using the remote control
Keep in mind the following when using the
remote control:
• Make sure that there are no obstacles
between the remote and the remote
sensor on the unit.
• The remote has a range of about 7m.
• Remote operation may become unreliable
if strong sunlight or fluorescent light is
shining on the unit’s remote sensor.
• Remote controllers for different devices
can interfere with each other. Avoid using
remotes for other equipment located
close to this unit.
7
En
DV260.book 8 ページ 2003年1月28日 火曜日 午後7時20分
01
Before you start
• Replace the batteries when you notice a
fall off in the operating range of the
remote.
Disc / content format
playback compatibility
General disc compatibility
This player was designed and engineered to
be compatible with software bearing one or
more of the following logos:
DVD-Video
DVD-R
DVD-Audio / SACD / DVD-RAM
DVD-ROM / CD-ROM*
* Except those that contain MP3, WMA or
JPEG. See also Compressed audio compatibility and JPEG file compatibility below.
DVD-R/RW and CD-R/RW discs (Audio CDs
and Video CD/Super VCDs) recorded using a
DVD recorder, CD recorder or personal
computer may not be playable on this unit.
This may be caused by a number of possibilities, including but not limited to: the type of
disc used; the type of recording; damage, dirt
or condensation on either the disc or the
player’s pick-up lens. See below for notes
about particular software and formats.
DVD-RW
CD-R/RW compatibility
Audio CD
Video CD
CD-R
CD-RW
Fujicolor CD
• KODAK Picture CD
•
is a trademark of Fuji Photo Film Co.
Ltd.
This player supports the IEC’s Super VCD
standard. Compared to the Video CD standard, Super VCD offers superior picture
quality, and allows two stereo soundtracks to
be recorded. Super VCD also supports the
widescreen size.
VIDEO
CD
Super Video CD (Super VCD)
Other formats, including but not limited to the
following, are not playable in this player:
8
En
• This unit will play CD-R and CD-RW discs
recorded in CD Audio or Video CD/Super
VCD format, or as a CD-ROM containing
MP3, WMA or JPEG files. However, any
other content may cause the disc not to
play, or create noise/distortion in the
output.
• This unit cannot record CD-R or CD-RW
discs.
• Unfinalized CD-R/RW discs recorded as
CD Audio can be played, but the full Table
of Contents (playing time, etc.) will not be
displayed.
DVD-R/RW compatibility
• This unit will play DVD-R/RW discs
recorded using the DVD-Video format that
have been finalized using a DVD-recorder.
• This unit will play DVD-RW discs recorded
using the Video Recording (VR) format.
• DVD-RW shows in the display when a VR
format DVD-RW disc is loading.
DV260.book 9 ページ 2003年1月28日 火曜日 午後7時20分
01
Before you start
• When playing a VR format DVD-RW discs
that was edited on a DVD recorder, the
screen may go momentarily black at
edited points and/or you may see scenes
from immediately before the edited point.
• This unit cannot record DVD-R/RW discs.
• Unfinalized DVD-R/RW discs cannot be
played in this player.
PC-created disc compatibility
• If you record a disc using a personal
computer, even if it is recorded in a
“compatible format” as listed above, there
will be cases in which the disc may not be
playable in this machine due to the
setting of the application software used to
create the disc. In these particular
instances, check with the software
publisher for more detailed information.
• Check the DVD-R/RW or CD-R/RW software disc boxes for additional compatibility information.
About WMA
WMA is short for Windows Media Audio and
refers to an audio compression technology
developed by Microsoft Corporation. WMA
data can be encoded by using Windows
Media Player version 8 (or less) or Windows
Media Player for Windows XP.
Windows Media, and the Windows logo are
trademarks, or registered trademarks of
Microsoft Corporation in the United States
and/or other countries.
Compressed audio compatibility
• This unit will play CD-ROM, CD-R, and
CD-RW discs containing files saved in the
MPEG-1 Audio Layer 3 (MP3) or Windows
Media Audio (WMA) format with a
sampling rate of 32*, 44.1 or 48kHz.
Incompatible files will not play and the
message Can’t play this format will be
displayed (NO PLAY in the front panel
display).
* This unit will not play 32kHz WMA files
encoded at 20kbps.
• Fixed bit-rate MP3 files are recommended. Variable bit-rate (VBR) MP3 files
are playable, but playing time may not be
shown correctly.
• This player is compatible with WMA data
encoded using Windows Media Player
version 8 (or less) or Windows Media
Player for Windows XP.
• This player is not compatible with lossless-encoding or variable bit-rate (VBR)
WMA files.
• WMA files encoded with DRM (Digital
Rights Management) copy protection will
not play and the message Can’t play this
format will be displayed (NO PLAY in the
front panel display).
The Windows Media™ logo printed on the box
indicates that this player can playback WMA
data.
9
En
DV260.book 10 ページ 2003年1月28日 火曜日 午後7時20分
01
Before you start
• The CD-ROM used to compile your WMA/
MP3 files must be ISO 9660 Level 1 or 2
compliant. CD physical format: Mode1,
Mode2 XA Form1. Romeo and Joliet file
systems are both compatible with this
player.
• Use CD-R or CD-RW media for recording
your files. The disc must be finalized (i.e.
the session must be closed) in order to
play in this unit. This player is not compatible with multi-session discs. Only the first
session of a multi-session disc will be
recognized.
• This player only plays tracks that are
named with the file extension .mp3,
.MP3, .wma, or .WMA.
• When naming MP3 and WMA files, add
the corresponding file name extension
(.mp3 or .wma). Files are played
according to the file extension. To prevent
noise and malfunctions, do not use these
extensions for other kinds of files.
• This player can recognize up to 999 files
(WMA/MP3/JPEG) and up to 499 folders.
If a disc exceeds these limits, only files
and folders up to these limits will be playable. Files and folders are read/displayed
in alphabetical order. Note that if the file
structure is very complex, you may not be
able to read/play all files on the disc.
• Folder and track names (excluding the file
extension) are displayed.
• There are many different recording bitrates available to encode MP3 files. This
unit was designed to be compatible with
all of them. Audio encoded at 128Kbps
should sound close to regular CD Audio
quality. This player will play lower bit-rate
files, but please note that the sound
quality becomes noticeably worse at
lower bit-rates.
10
En
JPEG file compatibility
• Baseline JPEG and EXIF 2.1* still image
files up to 8 mega-pixels are supported
(maximum vertical and horizontal resolution is 5120 pixels). (*File format used by
digital still cameras)
• The CD-ROM used to compile your JPEG
files must be ISO 9660 Level 1 or 2
compliant. CD physical format: Mode1,
Mode2 XA Form1. Romeo and Joliet file
systems are both compatible with this
player.
• This player only displays files that are
named with the file extension .jpg or
.JPG.
DV260.book 11 ページ 2003年1月28日 火曜日 午後7時20分
02
Connecting up
Chapter 2
Connecting up
Rear panel connections
1
2
DIGITAL AUDIO OUT
Y
3
PB
COAXIAL
4
AUDIO OUT
L
VIDEO OUT
D1 /D2
R
OPTICAL
S
PR
COMPONENT VIDEO OUT
VIDEO OUT
Taiwanese model
8
7
6
• When connecting this player up to your
TV, AV receiver or other components,
make sure that all components are
switched off and unplugged.
1 DIGITAL AUDIO OUT – COAXIAL
This is a digital audio output for connection to
a PCM, Dolby Digital, DTS and/or MPEGcompatible AV receiver that has a coaxial
digital input.
Connect using a commercially available
coaxial digital audio cable.
2 COMPONENT VIDEO OUT
This is a high quality video output for connection to a TV, monitor or AV receiver that has
component video inputs.
Connect using a commercially available
three-way component video cable. Be careful
to match the colors of the jacks and cables for
correct connection.
5
3 AUDIO OUT L / R
This pair of analog audio outputs connects to
your TV, AV receiver or stereo system. Even if
you are connecting up one of the digital
outputs, we still recommend you connect
these jacks.
Use the supplied audio/video cable when
connecting these jacks. Match the colors of
the jacks and cables for correct stereo sound.
4 AC IN
Connect the supplied power cable here, then
plug into a power outlet.
5 VIDEO OUT D1/D2 (Taiwanese model
only)
Use to connect this player to a TV with a D
video input.
6 VIDEO OUT
This is a standard video output that you can
connect to your TV or AV receiver using the
supplied audio/video cable.
11
En
DV260.book 12 ページ 2003年1月28日 火曜日 午後7時20分
02
Connecting up
7 S (S-video output)
This is an S-video output that you can use
instead of the video output described in 5
above.
8 DIGITAL AUDIO OUT – OPTICAL
This is a digital audio output for connection to
a PCM, Dolby Digital, DTS and/or MPEGcompatible AV receiver that has an optical
digital input.
• You may find it useful to have the manuals
supplied with your other components
handy when connecting this player.
• If you come across any unfamiliar terms
in this section of the manual, turn to the
Glossary on page 66.
Connect using a commercially available
optical digital audio cable.
Easy connections
The setup described here is a basic setup that allows you to play discs using just the cables
supplied with the player. In this setup, stereo audio is played through the speakers in your TV.
A/V IN
TV
DIGITAL AUDIO OUT
Y
PB
COAXIAL
AUDIO OUT
L
R
OPTICAL
S
PR
COMPONENT VIDEO OUT
VIDEO OUT
To power outlet
12
En
DV260.book 13 ページ 2003年1月28日 火曜日 午後7時20分
02
Connecting up
• This player is equipped with copy protection technology. Do not connect this
player to your TV via a VCR using AV
cables, as the picture from this player will
not appear properly on your TV. (This
player may also not be compatible with
some combination TV/VCRs for the same
reason; refer to the manufacturer for
more information.)
• When connecting to your TV as shown
above, do not set the Component Out
setting (page 52) to Progressive.
1 Connect the VIDEO OUT and AUDIO
OUT L/R jacks to a set of A/V inputs on
your TV.
Use the supplied audio/video cable,
connecting the red and white plugs to the
audio outputs and the yellow plug to the video
output. Make sure you match up the left and
right audio outputs with their corresponding
inputs for correct stereo sound.
See below if you want to use a component or
S-video cable for the video connection.
2 Connect the supplied AC power cable
to the AC IN inlet, then plug into a power
outlet.
• When TV System is set to AUTO or NTSC,
and playing an NTSC disc only: When
Component Out (page 52) is set to
Progressive, there is no video output
from the VIDEO OUT (composite) and S
(S-video) jacks. If you want to display video
on more than one monitor simultaneously, make sure that it is set to Interlace. Switch the player to standby then,
using the front panel controls, press
STANDBY/ON while pressing to switch the player back to Interlace.
Connecting using the S-video
output
If your TV (or other equipment) has an S-video
input, you can use this instead of the standard (composite) output for a better quality
picture.
• Use an S-video cable (not supplied) to
connect the S-VIDEO OUT to an S-video
input on your TV (or monitor or AV
receiver).
Line up the small triangle above the jack with
the same mark on the plug before plugging
in.
S-VIDEO
IN
• Before unplugging the player from the
power outlet, make sure you first switch it
into standby using either the front panel
STANDBY/ON button, or the remote
control, and wait of the -OFF- message to
disappear from the player’s display.
TV
DIGITAL AUDIO OUT
Y
PB
COAXIAL
AUDIO OUT
L
R
OPTICAL
S
PR
COMPONENT VIDEO OUT
VIDEO OUT
• For the above reasons, do not plug this
player into a switched power supply found
on some amplifiers and AV receivers.
13
En
DV260.book 14 ページ 2003年1月28日 火曜日 午後7時20分
02
Connecting up
Connecting using the
component video output
You can use the component video output
instead of the standard video out jack to
connect this player to your TV (or other equipment). This should give you the best quality
picture from the three types of video output
available.
• Use a component video cable (not
supplied) to connect the COMPONENT
VIDEO OUT jacks to a component video
input on your TV, monitor or AV receiver.
Taiwanese model only:
Connecting using the D1/D2
video output
If your TV is equipped with a D type video
input, you can use a D video cable to connect
this player to your TV.
• Use a D video cable (not supplied) to
connect the VIDEO OUT D1/D2 jacks to a D
type video input on your TV, monitor or
AV receiver.
D VIDEO
INPUT
COMPONENT
VIDEO IN
TV
TV
DIGITAL AUDIO OUT
DIGITAL AUDIO OUT
Y
PB
COAXIAL
AUDIO OUT
Y
PB
COAXIAL
AUDIO OUT
L
VIDEO OUT
D1 /D2
L
R
R
OPTICAL
S
PR
• To set up the player for use with a progressive scan TV, see Component Out on
page 52.
14
En
OPTICAL
S
PR
COMPONENT VIDEO OUT
VIDEO OUT
COMPONENT VIDEO OUT
VIDEO OUT
Taiwanese model
• The D video output on this player outputs
only NTSC video.
DV260.book 15 ページ 2003年1月28日 火曜日 午後7時20分
02
Connecting up
Connecting to an AV receiver
To enjoy multichannel surround sound you
need to connect this player to an AV receiver
using a digital output. This player has both
coaxial and optical digital jacks; use whichever is convenient.
In addition to a digital connection, we recommend also connecting using the stereo
analog connection.
You’ll probably also want to connect a video
output to your AV receiver. You can use any of
the video outputs available on this player (the
illustration shows a standard (composite)
connection).
1 Connect one of DIGITAL AUDIO OUT
jacks on this player to a digital input on
your AV receiver.
DIGITAL IN
(OPTICAL)
DIGITAL IN
(COAXIAL)
AV receiver
DIGITAL AUDIO OUT
Y
PB
COAXIAL
AUDIO OUT
L
R
OPTICAL
S
PR
COMPONENT VIDEO OUT
2 Connect the analog AUDIO OUT L/R
and VIDEO OUT jacks on this player to a
set of analog audio and video inputs on
your AV receiver.
AUDIO/
VIDEO IN
AV receiver
DIGITAL AUDIO OUT
Y
PB
COAXIAL
AUDIO OUT
L
R
OPTICAL
S
PR
COMPONENT VIDEO OUT
VIDEO OUT
The diagram shows standard video connections, but you can alternatively use the
S-video or component video connections if
they’re available.
3 Connect the AV receiver’s video
output to a video input on your TV.
• You usually have to connect the same
kind of video cable between your DVD
player and AV receiver, and between your
AV receiver and TV.
VIDEO OUT
This enables you to listen to multichannel
surround sound.
For an optical connection, use an optical
cable (not supplied) to connect the OPTICAL
DIGITAL AUDIO OUT jack to an optical input
on your AV receiver.
• My TV doesn’t have any inputs to connect
the DVD player. How can I watch DVDs?
If your TV has no inputs you can’t use this
player with it.
For a coaxial connection, use a coaxial cable
(similar to the supplied video cable) to
connect the COAXIAL DIGITAL AUDIO OUT
jack to a coaxial input on your AV receiver.
15
En
DV260.book 16 ページ 2003年1月28日 火曜日 午後7時20分
02
Connecting up
• My VCR is already connected to my TV, so
there aren’t any spare inputs. What should
I do?
If all your TV’s inputs are already in use,
you can buy a video input selector from an
electronics store, which effectively gives
you more inputs.
• My TV only has one input for the sound.
What should I plug it into?
If you don’t mind mono sound, you can
buy a stereo RCA-to-mono RCA cable
from an electronics store. Connect the
stereo end to this player and the mono
end to your TV.
If you want stereo sound, connect this
player to your amplifier or stereo system
using a stereo audio cable.
• I connected the DVD player to my AV
receiver, and although the sound is fine,
there’s no picture. What did I do wrong?
Make sure that the correct video input is
selected on your TV.
Also make sure that the type of video
connection from the DVD player to your
AV receiver is the same as that from the
receiver to your TV. Most AV receivers
won’t convert from one kind of connection
to another.
16
En
DV260.book 17 ページ 2003年1月28日 火曜日 午後7時20分
03
Controls and displays
Chapter 3
Controls and displays
Front panel
1
16
13
3
14
4
7
TOP MENU
OPEN/
CLOSE
HOME
MENU
STANDBY/ON
15
DV-266-s
1
2
12 5
3
8
MENU
ENTER
RETURN
6
11
4
7
10
8
9
TOP MENU
FL DIMMER
DV-366-s
DV-366-K
1
16
15
14
13 12
HOME
MENU
3
4
5
MENU
OPEN/CLOSE
STANDBY/ON
9
6
RETURN
11
5
ENTER
10
6
OPEN/CLOSE
STANDBY/ON
DV-466-s
DV-466-K
14
13
15 12
16
17
En
DV260.book 18 ページ 2003年1月28日 火曜日 午後7時20分
03
Controls and displays
1 STANDBY/ON
Press to switch the player on or into standby.
2 FL DIMMER
Press to dim or brighten the display.
3
Disc tray
4 OPEN/CLOSE
Press to open or close the disc tray.
5 Press to pause playback. Press again to
restart.
6 Press to start or resume playback.
7 TOP MENU
Press to display the top menu of a DVD disc.
8 ENTER & cursor buttons
Use to navigate on-screen displays and
menus. Press ENTER to select an option or
execute a command.
9 MENU
Press to display a DVD disc menu, or the Disc
Navigator if a VR format DVD-RW, CD, Video
CD/Super VCD, MP3, WMA or JPEG disc is
loaded.
10 RETURN
Press to return to a previous menu screen.
11 HOME MENU
Press to display (or exit).
12 Press to stop the disc (you can resume playback by pressing (play)).
18
En
13 Remote control sensor
The remote control has a range of up to about
7m.
14 Display
See page 19 for a description of the display.
15 and • Press and hold for fast reverse/forward
scanning.
• Press to jump to the previous/next
chapter or track.
16
This mark indicates compatibility with
DVD-RW discs recorded on a DVD recorder in
Video Recording mode.
DV260.book 19 ページ 2003年1月28日 火曜日 午後7時20分
03
Controls and displays
Display
1
2
3
4
DV-266-s
10 6
5
5
6
7
8
9
3
4
11
2
12 1
7
8
9
DV-366-s/ DV-366-K/ DV-466-s/ DV-466-K
1 and Indicates whether a disc is playing or paused.
2 CHP
Indicates that the character display is
showing a DVD chapter number.
8 REMAIN
Indicates that the character display is
showing the disc or title/chapter/track remain
time.
9
Character display
3 TITLE
Indicates that the character display is
showing a DVD title number.
10 2 D
Lights when a Dolby Digital soundtrack is
playing.
4
Lights when 2V/SRS TruSurround is
selected.
11 TRK
Indicates that the character display is
showing a CD or Video CD/Super VCD track
number.
5
Lights during multi-angle scenes on a DVD
disc.
12 DTS
Lights when a DTS soundtrack is playing.
6 PRGSVE
Lights when the player is set to output
progressive scan video (see Component Out
on page 52).
7
Lights in any of the repeat play modes.
19
En
DV260.book 20 ページ 2003年1月28日 火曜日 午後7時20分
03
Controls and displays
1 STANDBY/ON
Press to switch the player on or into standby.
Remote control
1
3
STANDBY/ON
OPEN/CLOSE
14
ANGLE
15
2 AUDIO
Press to select the audio channel or language
(see Switching DVD audio language on
page 40).
2
AUDIO
4
1
2
3
CLEAR
16
3 SUBTITLE
Press to select a subtitle display (see
Switching subtitles on page 40).
4
5
6
ENTER
17
4
7
8
9
SUBTITLE
TOP MENU
18
6
6 ENTER & cursor buttons
Use to navigate on-screen displays and
menus. Press ENTER to select an option or
execute a command.
ENTER
HOME
MENU
RETURN
19
7
/
8
5 TOP MENU
Press to display the top menu of a DVD disc.
0
MENU
5
7 HOME MENU
Press to display (or exit) the on-screen
display.
/
20
21
ZOOM
DISPLAY
9
10
11
PLAY MODE SURROUND
12
13
Number buttons
23
24
22
8 and /
Use for reverse slow motion playback, frame
reverse and reverse scanning.
9 Press to start or resume playback.
10 Press to jump to the beginning of the current
chapter or track, then to previous chapters/
tracks.
11 Press to pause playback; press again to
restart.
12 PLAY MODE
Press to display the Play Mode menu. (You
can also get to the Play Mode menu by
pressing HOME MENU and selecting Play
Mode).
20
En
DV260.book 21 ページ 2003年1月28日 火曜日 午後7時20分
03
Controls and displays
13 SURROUND
Press to activate/switch off 2V/SRS TruSurround.
14 OPEN/CLOSE
Press to open or close the disc tray.
15 ANGLE
Press to change the camera angle during
DVD multi-angle scene playback (see
Switching camera angles on page 42).
16 CLEAR
Press to clear a numeric entry.
17 ENTER
Use to select menu options, etc. (works
exactly the same as the ENTER button in 6
above).
18 MENU
Press to display a DVD disc menu, or the Disc
Navigator if a VR format DVD-RW, CD, Video
CD/Super VCD, MP3, WMA or JPEG disc is
loaded.
19 RETURN
Press to return to a previous menu screen.
20 and /
Use for forward slow motion playback, frame
advance and forward scanning.
21 Press to jump to the next chapter or track.
22 Press to stop the disc (you can resume playback by pressing (play)).
23 DISPLAY
Press to display information about the disc
playing (see Displaying disc information on
page 42).
24 ZOOM
Press to change the zoom level (see Zooming
the screen on page 41).
21
En
DV260.book 22 ページ 2003年1月28日 火曜日 午後7時20分
04
Getting started
Chapter 4
Getting started
Switching on
Let’s Get Started
After making sure that everything is
connected properly and that the player is
plugged in, press STANDBY/ON on the
front panel, or on the remote control to switch
the player on.
When you switch on the player for the first
time, you should see a welcome screen
displayed on your TV. From here you can let
the player know what kind of TV you have,
then either use the Setup Navigator to make
more settings, or jump right in and start
playing some discs.
Also, switch on your TV and make sure that it
is set to the input you connected the DVD
player to.
STANDBY/ON
ENTER
FL DIMMER
STANDBY/ON
GUIDE
RETURN
DV-366-S/ DV-366-K
• My DVD player switches on but there is
nothing displayed on my TV.
Make sure that the TV is set to the correct
video input (not a TV channel). For
example, if you connected this player to
the VIDEO 1 inputs on your TV, switch
your TV to VIDEO 1.
• This player features a screen saver and an
auto power off function. If the player is
stopped and no button is pressed for five
minutes, the screen saver starts. If the
disc tray is closed but no disc is playing
and no control is pressed for 30 minutes,
the player automatically goes into
standby.
22
En
• For customers in Taiwan: The default onscreen menu language is Traditional
Chinese. Use the instructions below to
complete the Let’s Get Started setup, then
see page 69 for instructions on changing
the on-screen display language to
English.
DV260.book 23 ページ 2003年1月28日 火曜日 午後7時20分
04
Getting started
1 Press ENTER to move on to the next
screen.
Taiwanese model only
Welcome to Pioneer DVD!
Thank you for purchasing this Pioneer DVD player.
Before using, please take a little time
to setup your DVD player
Put the batteries into the remote control
Next, press the ENTER button on the remote control
and start the Let's Get Started Menu
Next
3
Taiwanese model only
Press ENTER again to finish setting up.
Let's Get Started Menu
Setup complete
If you're finished setting up,
choose [Complete],
to start again choose [Back]
Complete
Back
Taiwanese model only
2 Use the / (cursor left/right)
buttons to select either ‘Wide screen
(16:9)’ or ‘Standard size screen (4:3)’
according to the kind of TV you have, then
press ENTER.
Let's Get Started Menu
What kind of TV do you have?
Use the
/
cursor buttons
to choose, then press ENTER
Wide screen (16:9)
Standard size screen (4:3)
• Select Back then press ENTER if you want
to go back and change the setting you just
made.
23
En
DV260.book 24 ページ 2003年1月28日 火曜日 午後7時20分
04
Getting started
Using the on-screen displays
For ease of use, this player makes extensive
use of graphical on-screen displays (OSDs).
You should get used to the way these work as
you’ll need to use them when setting up the
player, using some of the playback features,
such as program play, and when making
more advanced settings for audio and video.
All the screens are navigated in basically the
same way, using the cursor buttons (//
/)to change the highlighted item and
pressing ENTER to select it.
• Throughout this manual, ‘Select’ means
use the cursor buttons to highlight an
item on-screen, then press ENTER.
ENTER
ENTER
HOME
MENU
GUIDE
RETURN
Button
What it does
HOME
MENU
Display/exit the on-screen display.
/// Changes the highlighted menu
item.
24
En
ENTER
Selects the highlighted menu
item (both ENTER buttons work
in exactly the same way).
RETURN
Returns to the main menu without saving changes.
• If you’re using the DV–266-S, DV-366-S, or
DV-366-K, the buttons to navigate the onscreen displays are available on the front
panel as well as the remote control. (See
Front panel on page 17 for the location
and description of all the front panel
controls for your model.)
• The button guide at the bottom of every
OSD screen shows you which buttons
you’ll need to use for that screen.
DV260.book 25 ページ 2003年1月28日 火曜日 午後7時20分
04
Getting started
Setting up with the Setup
Navigator
Using the Setup Navigator you can make a
number of other initial settings for this player.
We recommend using the Setup Navigator,
especially if you connected this player to an
AV receiver for playing surround sound. To
answer some of the questions about digital
audio formats you may need to look at the
instructions that came with your AV receiver.
1 If a disc is playing, press (stop).
Also turn on your TV and make sure that it is
set to the correct video input.
2 Press HOME MENU.
The on-screen display (OSD) appears.
HOME MENU
DVD
Audio Settings
Video Adjust
Play Mode
Disc Navigator
Setup Navigator
Initial Settings
3
Select ‘Setup Navigator’.
HOME MENU
DVD
Audio Settings
Video Adjust
Play Mode
Disc Navigator
Initial Settings
4 Select a DVD language.
Some DVD discs feature on-screen menus,
soundtracks and subtitles in several
languages. Set your preferred language here.
Setup Navigator
Language Settings
Audio Out Settings
AV Receiver Func.
DVD Language
English
French
Spanish
Chinese
Other Language
Taiwanese model only
Setup Navigator
Language Settings
Audio Out Settings
AV Receiver Func.
DVD Language
Chinese
English
Other Language
• Note that the language you choose here
may not be available on all discs.
• If you want to select a language other
than those listed, select Other
Language. See Selecting languages using
the language code list on page 64 for
detailed information.
5 Did you connect this player to an
amplifier or AV receiver?
Select Connected or Not Connected.
Setup Navigator
Setup Navigator
Language Settings
Audio Out Settings
AV Receiver Func.
AV Receiver
Connected
Not Connected
25
En
DV260.book 26 ページ 2003年1月28日 火曜日 午後7時20分
04
Getting started
• If you selected Not Connected here, that
completes setup using the Setup Navigator. Press ENTER to exit.
6 Did you connect this player to an AV
receiver using a digital output?
Select Connected or Not Connected.
9 Is your AV receiver MPEG compatible?
Select Compatible, Not Compatible or
Don’t Know.
Setup Navigator
Language Settings
Audio Out Settings
AV Receiver Func.
Dolby Digital
DTS
MPEG
Compatible
Not Compatible
Don't Know
Setup Navigator
Language Settings
Audio Out Settings
AV Receiver Func.
AV Receiver
Digital Audio Out
Connected
Not Connected
• If you selected Not Connected here, that
completes setup using the Setup Navigator. Press ENTER to exit.
7 Is your AV receiver Dolby Digital
compatible?
Select Compatible, Not Compatible or
Don’t Know.
Setup Navigator
Language Settings
Audio Out Settings
AV Receiver Func.
Dolby Digital
Compatible
Not Compatible
Don't Know
10 Is your AV receiver compatible with
96kHz Linear PCM audio?
Select Compatible, Not Compatible or
Don’t Know.
Setup Navigator
Language Settings
Audio Out Settings
AV Receiver Func.
Dolby Digital
DTS
MPEG
Compatible
Not Compatible
Don't Know
96kHz Linear PCM
11 Press ENTER to complete the setup, or
press HOME MENU to quit the Setup Navigator without making any changes.
Setup Navigator
8 Is your AV receiver DTS compatible?
Select Compatible, Not Compatible or
Don’t Know.
Setup Navigator
Language Settings
Audio Out Settings
AV Receiver Func.
26
En
Language Settings
Audio Out Settings
AV Receiver Func.
Dolby Digital
Compatible
Not Compatible
DTS
Settings complete
Unknown
MPEG
Press ENTER to exit
96kHz Linear PCM
ENTER
Congratulations, setup is complete!
Dolby Digital
DTS
Compatible
Not Compatible
Don't Know
DV260.book 27 ページ 2003年1月28日 火曜日 午後7時20分
04
Getting started
Playing discs
The basic playback controls for playing DVD,
CD, Video CD/Super VCD and WMA/MP3
discs are covered here. Further functions are
detailed in the next chapter.
STANDBY/ON
OPEN/CLOSE
1
2
3
4
5
6
ENTER
7
8
9
0
3 Load a disc.
Load a disc with the label side facing up,
using the disc tray guide to align the disc (if
you’re loading a double-sided DVD disc, load
it with the side you want to play face down).
ENTER
/
/
4 Press (play) to start playback.
If you’re playing a DVD or Video CD/Super
VCD, a menu may appear. See DVD-Video disc
menus on page 30 and Video CD/Super VCD
PBC menus on page 31 for more on how to
navigate these.
If you’re playing an WMA/MP3 disc, it may
take a few seconds before playback starts,
depending on the complexity of the file structure on the disc.
1 If the player isn’t already on, press
STANDBY/ON to switch it on.
If you’re playing a DVD or Video CD/Super
VCD, also turn on your TV and make sure that
it is set to the correct video input.
2 Press OPEN/CLOSE to open the disc
tray.
If you loaded a CD/CD-R/RW containing
JPEGs, a slideshow will start. See Viewing
JPEG discs on page 44 for more on playing
these discs.
• See also PhotoViewer on page 59 if the
disc contains both WMA/MP3 audio files
and JPEG picture files (by default, you will
not be able to play the WMA/MP3 files).
27
En
DV260.book 28 ページ 2003年1月28日 火曜日 午後7時20分
04
Getting started
• After I load a DVD disc, it ejects automatically after a few seconds!
Most likely, the disc is the wrong region
for your player. The region number should
be printed on the disc; check it against
the region number of the player (which
you can find on the rear panel). See also
DVD-Video regions on page 64.
If the region number is OK, it may be that
the disc is damaged or dirty. Clean the
disc and look for signs of damage. See
also Taking care of your player and discs on
page 60.
• Why won’t the disc I loaded play?
First check that you loaded the disc the
right way up (label side up), and that it’s
clean and not damaged. See Taking care
of your player and discs on page 60 for
information on cleaning discs.
If a disc loaded correctly won’t play, it’s
probably an incompatible format or disc
type, such as DVD-Audio or DVD-ROM.
See Disc / content format playback
compatibility on page 8 for more on disc
compatibility.
• I have a widescreen TV so why are there
black bars at the top and bottom of the
screen when I play some discs?
Some movie formats are such that even
when played on a widescreen TV, black
bars are necessary at the top and bottom
of the screen. This is not a malfunction.
28
En
• I have a standard (4:3) TV and set the player
to show widescreen DVDs in pan & scan
format, so why do I still get black bars top
and bottom with some discs?
Some discs override the display preferences of the player, so even if you have 4:3
(Pan & Scan) selected, those discs will
still be shown in letter box format. This is
not a malfunction.
• My AV receiver is definitely compatible with
96kHz Linear PCM audio, but it doesn’t
seem to work with this player. What’s
wrong?
For digital copy-protection purposes,
some 96kHz DVD discs are automatically
downsampled to 48kHz. This is not a
malfunction. With these kinds of discs, if
you want to enjoy high-quality analog
audio, set Digital Out to Off (see Digital
Out on page 50), and 96kHz PCM Out to
96kHz (see 96kHz PCM Out on page 51).
DV260.book 29 ページ 2003年1月28日 火曜日 午後7時20分
04
Getting started
Basic playback controls
The table below shows the basic controls on
the remote for playing discs. The following
chapter covers more playback features in
more detail.
Button
What it does
Starts playback.
DVD and Video CD/Super VCD: If
the display shows RESUME or
LAST MEM playback starts from
the resume or last memory point
(see also Resume and Last Memory below.)
Pauses a disc that’s playing, or
restarts a paused disc.
Stops playback.
DVD and Video CD/Super VCD:
Display shows RESUME. Press (stop) again to cancel the resume
function. (See also Resume and
Last Memory below.)
Press to start fast reverse scanning. Press (play) to resume
normal playback.
Press to start fast forward scanning. Press (play) to resume
normal playback.
Skips to the start of the current
track or chapter, then to previous
tracks/chapters.
Skips to the next track or chapter.
Button
What it does
Numbers
Use to enter a title/track number.
Press ENTER to select (or wait a
few seconds).
• If the disc is stopped, playback
starts from the selected title (for
DVD) or track number (for CD/
Video CD/Super VCD/WMA/MP3 ).
• If the disc is playing, playback
jumps to the start of the selected
chapter or track.
Front panel controls
The (play), (stop), and (pause) buttons
on the front panel work in exactly the same
way as their remote control equivalents.
The combined scan/skip buttons on the front
panel ( and ) work slightly
differently from the remote buttons. Press
and hold for fast scan; press for track/chapter
skip.
See Front panel on page 17 for the location
and description of all the front panel controls
for your model.
• You may find with some DVD discs that
some playback controls don’t work in
certain parts of the disc. This is not a
malfunction.
• Track skip and number buttons for track
selection do not work with unfinalized CDR/RW discs.
29
En
DV260.book 30 ページ 2003年1月28日 火曜日 午後7時20分
04
Getting started
Resume and Last Memory
When you stop playback of a DVD or Video
CD/Super VCD disc, RESUME is shown in the
display indicating that you can resume playback again from that point.
If you want to clear the resume/last memory
point, press (stop) while RESUME or LAST
MEM is displayed.
• When a Video CD/Super VCD is loaded,
the Resume point is lost if the player is
switched off.
• For the Last Memory function to work, you
must press (stop) to stop playback
before opening the disc tray.
• The Last Memory function doesn’t work
with VR format DVD-RW discs.
2
3
4
5
6
7
8
9
TOP MENU
If the disc tray is not opened, the next time you
start playback the display shows RESUME
and playback resumes from the resume point.
For DVD discs only: If you take the disc out of
the player, the play position is stored in
memory. When you load the disc next time,
the display shows LAST MEM and you can
resume playback (this works for up to five
discs).
1
ENTER
0
MENU
ENTER
RETURN
Button
What it does
TOP MENU
Displays the ‘top menu’ of a DVD
disc—this varies with the disc.
MENU
Displays a DVD disc menu—this
varies with the disc and may be
the same as the ‘top menu’.
/// Moves the cursor around the
screen.
ENTER
Selects the current menu option.
RETURN
Returns to the previously displayed menu screen.
Numbers
Highlights a numbered menu
option (some discs only). Press
ENTER to select.
DVD-Video disc menus
Many DVD-Video discs contain menus from
which you can select what you want to watch.
They may give access to additional features,
such as subtitle and audio language selection, or special features such as slideshows.
See the disc packaging for details.
Sometimes DVD-Video menus are displayed
automatically when you start playback; others
only appear when you press MENU or TOP
MENU.
30
En
• If you’re using the DV–266-S, DV-366-S, or
DV-366-K, most of the buttons to navigate
DVD disc menus are available on the front
panel as well as the remote control. (See
Front panel on page 17 for the location
and description of all the front panel
controls for your model.)
DV260.book 31 ページ 2003年1月28日 火曜日 午後7時20分
04
Getting started
Video CD/Super VCD PBC menus
Some Video CD/Super VCDs have menus
from which you can choose what you want to
watch. These are called PBC (Playback
control) menus.
You can play a PBC Video CD/Super VCD
without having to navigate the PBC menu by
starting playback using a number button to
select a track, rather than the (play) button.
1
2
3
4
5
6
ENTER
7
8
9
0
ENTER
RETURN
Button
What it does
RETURN
Displays the PBC menu.
Numbers
Use to enter a numbered menu
option. Press ENTER to select.
Displays the previous menu page
(if there is one).
Displays the next menu page (if
there is one).
31
En
05_playing_discs.fm 32 ページ 2003年1月30日 木曜日 午後7時25分
05
Playing discs
Chapter 5
Playing discs
Introduction
Most of the features described in this chapter
make use of on-screen displays. For an explanation of how to navigate these, see Using the
on-screen displays on page 24.
Many of the functions covered in this chapter
apply to DVD discs, Video CD/Super VCDs,
CDs and WMA/MP3/JPEG discs, although
the exact operation of some varies slightly
with the kind of disc loaded.
1 Press HOME MENU and select ‘Disc
Navigator’ from the on-screen display.
Alternatively, if a VR format DVD-RW, CD,
Video CD/Super VCD or WMA/MP3/JPEG disc
is loaded, you can press MENU, which takes
you straight to the Disc Navigator screen.
HOME MENU
DVD
Some DVD discs restrict the use of some
functions (random or repeat, for example).
This is not a malfunction.
When playing Video CD/Super VCDs, some of
the functions are not available during PBC
playback. If you want to use them, start the
disc playing using a number button to select
a track.
Using the Disc Navigator to
browse the contents of a disc
Use the Disc Navigator to browse through the
contents of a disc to find the part you want to
play. You can use the Disc Navigator when a
disc is playing or stopped.
Audio Settings
Video Adjust
Play Mode
Disc Navigator
Initial Settings
Setup Navigator
2 Select what you want to play.
Depending on the type of disc you have
loaded, the Disc Navigator looks slightly
different.
The screen for DVD discs shows the titles on
the left and the chapters on the right. Select a
title, or a chapter within a title.
Disc Navigator
DVD
Title 1-10
Chapter 1-3
Title 01
Title 02
Title 03
Title 04
Title 05
Title 06
Title 07
Title 08
Chapter 001
Chapter 002
Chapter 003
For a VR (Video Recording) mode DVD-RW
disc select beween the Playlist and Original
areas of the disc, or a title. Press (cursor
right) to preview the title.
• It’s not possible to switch between Original and Playlist during playback.
32
En
DV260.book 33 ページ 2003年1月28日 火曜日 午後7時20分
05
Playing discs
• Not all VR format DVD-RW discs have a
Playlist.
Disc Navigator
DVD-RW
Original
Play List
Title(1-03)
01. 3/31 FIRST LEAGUE
02. 4/28 SECOND LEAGUE
03. 4/29 FINAL ROUND
• It’s not possible to use the Disc Navigator
when playing a Video CD/Super VCD in
PBC mode, or an unfinalized CD-R/RW
disc.
• Another way to find a particular place on
a disc is to use one of the search modes.
See Searching a disc on page 40.
Scanning discs
The screen for CDs and Video CD/Super VCDs
shows a list of tracks.
1 During playback, press or to
start scanning.
Disc Navigator
Track 1-10
CD
2 Press repeatedly to increase the scanning speed.
• WMA/MP3 tracks can only be scanned at
one speed.
Track 01
Track 02
Track 03
Track 04
Track 05
Track 06
Track 07
Track 08
• The scanning speed is shown on-screen.
The screen for an WMA/MP3 disc shows the
folder names on the left and the track names
on the right (note that if there are more than
16 folders or names that contain accented or
non-roman characters, tracks and folders
may show up with generic names – F_033,
T_035, etc.).
Select a folder, or a track within a folder.
Disc Navigator
WMA/MP3
You can fast-scan discs forward or backward
at various different speeds.
Folder 1-17
Track 1-10
001. ACP
002. Nth Degree
003. Pfeuti
004. Live
005. Glitch music
006. CodHead
007. Thermo
008. Missing Man
001. Gravity deluxe
002. Tesla's patent
003. Border dispute
004. Delayed by rain
005. Accident incident
006. Pigeon post
007. Outernational
008. Vacuum tube
Playback starts after you press ENTER.
3 To resume normal playback, press (play).
• Sound can be heard while scanning audio
CDs and MP3 discs.
• When scanning a Video CD/Super VCD or
WMA/MP3 track, playback automatically
resumes at the end or beginning of the
track.
• There is no sound while scanning DVDs,
Video CDs and WMA discs, and no subtitles while scanning DVDs.
• Depending on the disc, normal playback
may automatically resume when a new
chapter is reached on a DVD disc.
• The Disc Navigator is not available unless
there is a disc loaded.
33
En
DV260.book 34 ページ 2003年1月28日 火曜日 午後7時20分
05
Playing discs
Playing in slow motion
Frame advance/frame reverse
You can play DVDs and Video CD/Super VCDs
at four different forward slow motion speeds.
DVD-Video discs can also be played at two
reverse speeds. (With Video CD/Super VCDs
and VR format DVD-RWs, you can only use
forward slow motion playback.)
You can advance or back up a DVD disc
frame-by-frame. With Video CD/Super VCDs
and VR format DVD-RWs, you can only use
frame advance.
1
During playback, press (pause).
2 Press and hold / or / until
slow motion playback starts.
• The slow motion speed is shown onscreen.
• There is no sound during slow motion
playback.
3 Press repeatedly to change the slow
motion speed.
• The slow motion speed is displayed onscreen.
4 To resume normal playback, press (play).
• The picture quality during slow motion
playback is not as good as during normal
playback.
• Depending on the disc, normal playback
may automatically resume when a new
chapter is reached.
1
During playback, press (pause).
2 Press / or / to reverse or
advance a frame at a time.
3 To resume normal playback, press (play).
• The picture quality when using frame
reverse is not as good as frame advance.
• Depending on the disc, normal playback
may automatically resume when a new
chapter is reached.
• When changing direction with a DVD
disc, the picture may ‘move’ in an unexpected way. This is not a malfunction.
Looping a section of a disc
The A-B Repeat function allows you to specify
two points (A and B) within a track (CD and
Video CD/Super VCD) or title (DVD) that form
a loop which is played over and over.
• You can’t use A-B Repeat with WMA/MP3
discs, Video CD/Super VCDs in PBC
mode, or unfinalized CD-R/RW discs.
34
En
DV260.book 35 ページ 2003年1月28日 火曜日 午後7時20分
05
Playing discs
1 During playback, press PLAY MODE
and select ‘A-B Repeat’ from the list of
functions on the left.
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
A(Start Point)
B(End Point)
Off
2 Press ENTER on ‘A(Start Point)’ to set
the loop start point.
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
A(Start Point)
B(End Point)
Off
Using repeat play
There are various repeat play options,
depending on the kind of disc loaded. It’s also
possible to use repeat play together with
program play to repeat the tracks/chapters in
the program list (see Creating a program list
on page 37).
• You can’t use Repeat play with Video CD/
Super VCDs in PBC mode, or unfinalized
CD-R/RW discs.
1 During playback, press PLAY MODE
and select ‘Repeat’ from the list of functions on the left.
Play Mode
3 Press ENTER on ‘B(End Point)’ to set
the loop end point.
A-B Repeat
Repeat
Random
Program
Search Mode
Title Repeat
Chapter Repeat
Repeat Off
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
A(Start Point)
B(End Point)
Off
2 Select a repeat play option.
If program play is active, select Program
Repeat to repeat the program list, or Repeat
Off to cancel.
For DVD discs, select Title Repeat or
Chapter Repeat (or Repeat Off).
After pressing ENTER, playback jumps back
to the start point and plays the loop.
• The minimum loop time is 2 seconds.
4 To resume normal playback, select
‘Off’ from the menu.
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
Title Repeat
Chapter Repeat
Repeat Off
35
En
DV260.book 36 ページ 2003年1月28日 火曜日 午後7時20分
05
Playing discs
For CDs and Video CD/Super VCDs, select
Disc Repeat or Track Repeat (or Repeat
Off).
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
Disc Repeat
Track Repeat
Repeat Off
• You can’t use random play with VR format
DVD-RW discs, Video CD/Super VCDs
playing in PBC mode, or while a DVD disc
menu is being displayed.
1 Press PLAY MODE and select ‘Random’
from the list of functions on the left.
Play Mode
For WMA/MP3 discs, select Disc Repeat,
Folder Repeat or Track Repeat (or Repeat
Off).
A-B Repeat
Repeat
Random
Program
Search Mode
Random Title
Random Chapter
Random Off
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
Disc Repeat
Folder Repeat
Track Repeat
Repeat Off
2 Select a random play option.
For DVD discs, select Random Title or
Random Chapter, (or Random Off).
Play Mode
• You can’t use repeat and random play at
the same time.
• If you switch camera angle during repeat
play, repeat play is canceled.
Using random play
Use the random play function to play titles or
chapters (DVD-Video) or tracks (CD, Video
CD/Super VCD and WMA/MP3 discs) in a
random order.
You can set the random play option when a
disc is playing or stopped.
36
En
A-B Repeat
Repeat
Random
Program
Search Mode
Random Title
Random Chapter
Random Off
For CDs and Video CD/Super VCDs, select On
or Off to switch random play on or off.
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
On
Off
DV260.book 37 ページ 2003年1月28日 火曜日 午後7時20分
05
Playing discs
For WMA/MP3 discs, select Random All (all
folders) or Random Track (current folder
only), (or Random Off).
1 Press PLAY MODE and select ‘Program’
from the list of functions on the left.
Play Mode
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
Random All
Random Track
Random Off
A-B Repeat
Repeat
Random
Program
Search Mode
Create/Edit
Playback Start
Playback Stop
Program Delete
Program Memory
Off
2 Select ‘Create/Edit’ from the list of
program options.
Play Mode
• To stop the disc and cancel random playback, press (stop).
• To cancel random playback without stopping playback, press CLEAR. The disc will
play to the end, then stop.
• During random play, the and buttons function a little differently to
normal: returns to the beginning of
the current track/chapter. You can't go
back further than this. selects
another track/chapter at random from
those remaining.
• You can't use random play together with
program or repeat play.
Creating a program list
This feature lets you program the play order of
titles/chapters/folders/tracks on a disc.
A-B Repeat
Repeat
Random
Program
Search Mode
Create/Edit
Playback Start
Playback Stop
Program Delete
Program Memory
Off
The Program edit screen that appears
depends on the kind of disc loaded.
On the left side is the program list, then to the
right is a list of titles (if a DVD disc is loaded),
tracks (for CDs and Video CD/Super VCDs), or
folder names (for WMA/MP3 discs). On the
far right is a list of chapters (for DVD) or track
names (for WMA/MP3).
3 Select a title, chapter, folder or track
for the current step in the program list.
For a DVD disc, you can add a whole title, or a
chapter within a title to the program list.
• To add a title, select the title.
Program
• You can’t use Program play with VR
format DVD-RW discs, Video CD/Super
VCDs playing in PBC mode, or while a
DVD disc menu is being displayed.
Program Step
Title 1~38
Chapter 1~4
01. 01
02.
03.
04.
05.
06.
07.
08.
Title 01
Title 02
Title 03
Title 04
Title 05
Title 06
Title 07
Title 08
Chapter 001
Chapter 002
Chapter 003
Chapter 004
37
En
DV260.book 38 ページ 2003年1月28日 火曜日 午後7時20分
05
Playing discs
• To add a chapter, first highlight the title,
then press (cursor right) and select a
chapter from the list.
Program
• To add a track, first find the folder, then
press (cursor right) and select a track
name from the list.
Program
Program Step
Title 1-38
Chapter 1-4
Program Step
Folder 1-6
Track 1-10
01. 01-003
02.
03.
04.
05.
06.
07.
08.
Title 01
Title 02
Title 03
Title 04
Title 05
Title 06
Title 07
Title 08
Chapter 001
Chapter 002
Chapter 003
Chapter 004
01. 001-003
02.
03.
04.
05.
06.
07.
08.
001. ACP
002. Nth Degree
003. Pfeuti
004. Live
005. Glitch music
006. CodHead
001. Gravity deluxe
002. Tesla's patent
003. Border dispute
004. Delayed by rain
005. Accident incident
006. Pigeon post
007. Outernational
008. Vacuum tube
For a CD or Video CD/Super VCD, select a
track to add to the program list.
Program
Program Step
Track 1~12
01. 04
02.
03.
04.
05.
06.
07.
08.
Track 01
Track 02
Track 03
Track 04
Track 05
Track 06
Track 07
Track 08
After pressing ENTER to select the title/
chapter/folder/track, the step number automatically moves down one.
4 Repeat step 3 to build up a program
list.
A program list can contain up to 24 titles/
chapters/folders/tracks.
For an WMA/MP3 disc, you can add a whole
folder, or a track within a folder to the
program list.
5 To play the program list, press (play).
Program play remains active until you turn off
program play (see below), erase the program
list (see below), eject the disc or switch off the
player.
• To add a folder, select the folder.
Program
Program Step
Folder 1-6
Track 1-10
01. 001
02.
03.
04.
05.
06.
07.
08.
001. ACP
002. Nth Degree
003. Pfeuti
004. Live
005. Glitch music
006. CodHead
001. Gravity deluxe
002. Tesla's patent
003. Border dispute
004. Delayed by rain
005. Accident incident
006. Pigeon post
007. Outernational
008. Vacuum tube
• To save your program list and exit the
program edit screen without starting playback, press PLAY MODE or HOME
MENU. (Don’t press RETURN – your
program list won’t be saved.)
• During program play, press to skip to
the next program step.
• Press CLEAR during playback to switch
off program play. Press while stopped to
erase the program list.
38
En
DV260.book 39 ページ 2003年1月28日 火曜日 午後7時20分
05
Playing discs
Editing a program list
After creating a program list, you can add,
delete and change steps.
1 Press PLAY MODE and select ‘Program’
from the list of functions on the left.
2 Select ‘Create/Edit’ from the list of
program options.
Other functions available from the
program menu
As well as creating and editing a program list,
you can start program play, cancel program
play, erase the program list, and memorize a
program list from the Play Mode menu.
1 Press PLAY MODE and select ‘Program’
from the list of functions on the left.
3 To clear a step, highlight the step
number and press CLEAR.
Play Mode
4 To insert a step in the middle of the
program list, highlight the step where you
want the new step to appear, then select
a title/chapter/folder/track to add.
After pressing ENTER, the new step is
inserted into the list.
5 To add a step to the end of the
program list, highlight the next free step
then select a title/chapter/folder/track to
add.
A-B Repeat
Repeat
Random
Program
Search Mode
2
Create/Edit
Playback Start
Playback Stop
Program Delete
Program Memory
Off
Select a program play function.
• Create/Edit – See above
• Playback Start – Starts playback of a
saved program list
• Playback Stop – Turns off program play,
but does not erase the program list
• To save your program list and exit the
program edit screen without starting playback, press PLAY MODE or HOME
MENU.
• If you want to exit the program edit screen
without saving the changes you made,
press RETURN.
• Program Delete – Erases the program
list and turns off program play
• Program Memory (DVD only) – Select
On to save the program list for the disc
loaded. (Select Off to cancel the program
memory for the disc loaded)
• Program lists are saved for the DVD disc
loaded. When you load a disc with a saved
program list, program play is automatically turned on.
• You can save program lists for up to 24
discs. After that, the oldest one is
replaced with the new one saved.
39
En
DV260.book 40 ページ 2003年1月28日 火曜日 午後7時20分
05
Playing discs
Searching a disc
You can search DVD discs by title or chapter
number, or by time. CDs can be searched by
track number, and Video CD/Super VCDs by
track number or time. WMA/MP3 discs can
be searched by folder or track number.
1 Press PLAY MODE and select ‘Search
Mode’ from the list of functions on the
left.
The search options that appear depend on the
kind of disc loaded. The screen below shows
the DVD search options.
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
Title Search
Chapter Search
Time Search
• The disc must be playing in order to use
time search.
• Search functions are not available with
Video CD/Super VCDs in PBC mode, or
unfinalized CD-R/RW discs.
Switching subtitles
Some DVD discs have subtitles in one or
more languages; the disc box will usually tell
you which subtitle languages are available.
You can switch subtitle language during playback.
1 Press SUBTITLE repeatedly to select a
subtitle option.
Current / Total
Subtitle
1/ 2
2
Select a search mode.
3 Use the number buttons to enter a
title, chapter, folder or track number, or a
time.
A-B Repeat
Repeat
Random
Program
Search Mode
Title Search
Chapter Search
Time Search
Input Chapter
0 0 1
• For a time search, enter the number of
minutes and seconds into the currently
playing title (DVD) or track (Video CD/
Super VCD) you want playback to resume
from. For example, press 4, 5, 0, 0 to have
playback start from 45 minutes into the
disc. For 1 hour, 20 minutes and 30
seconds, press 8, 0, 3, 0.
40
En
• Some discs only allow you to change
subtitle language from the disc menu.
Press TOP MENU to access.
• To set subtitle preferences, see Subtitle
Language on page 54.
Play Mode
4
English
Press ENTER to start playback.
Switching DVD audio
language
When playing a DVD disc recorded with
dialog in two or more languages, you can
switch audio language during playback.
1 Press AUDIO repeatedly to select an
audio language option.
Audio
Current /Total
1/ 2
French
Dolby Digital 3/2.1CH
DV260.book 41 ページ 2003年1月28日 火曜日 午後7時20分
05
Playing discs
Zooming the screen
• Some discs only allow you to change
audio language from the disc menu.
Press TOP MENU to access.
• To set audio language preferences, see
Audio Language on page 54.
Switching VR format DVD-RW
audio channel
When playing a VR format DVD-RW disc
recorded with dual-mono audio, you can
switch between the main, sub, and mixed
channels during playback.
1 Press AUDIO repeatedly to select an
audio channel option.
Audio
1L
1 During playback, use the ZOOM
button to select the zoom factor.
• Normal
• 2x
• 4x
Normal
Zoom 2x
Zoom 2x
Dolby Digital 1+1CH
Switching audio channel
when playing a Video CD/
Super VCD
When playing a Video CD, you can switch
between stereo, just the left channel or just
the right channel.
Super VCD supports four channels of audio.
You can switch the playback channel between
Stereo 1, Left 1, Right 1, Stereo 2, Left 2 and
Right 2 (note that not all Super VCDs have a
second soundtrack).
1 Press AUDIO repeatly to select an
audio channel option.
Audio
Using the zoom feature you can magnify a
part of the screen by a factor of 2 or 4, while
watching a DVD or Video CD/Super VCD.
Zoom 4x
Zoom 4x
• Since DVD and Video CD/Super VCD have
a fixed resolution, picture quality will deteriorate, especially at 4x zoom. This is not a
malfunction.
2 Use the cursor buttons to change the
zoomed area.
You can change the zoom factor and the
zoomed area freely during playback.
• If the navigation square at the top of the
screen disappears, press ZOOM again to
display it.
Stereo
41
En
DV260.book 42 ページ 2003年1月28日 火曜日 午後7時20分
05
Playing discs
• DVD displays
• We do not recommend using DVD disc
menus when the screen is zoomed as
menu options will not be highlighted.
• If you are displaying subtitles, these will
disappear when the screen is zoomed.
They will reappear when you return the
screen to normal.
Play
DVD
Current / Total
Elapsed
Remain
Title
11/38
2.05
4.57
1. French
1. English
Audio Dolby Digital 3/2.1CH
Subtitle
Play
Chapter
Tr. Rate
Total
7.02
1
Angle
DVD
Current / Total
11/38
Elapsed
2.05
Total
Remain
4.57
7.02
8.6Mbps
• VR format DVD-RW displays
Switching camera angles
Some DVD discs feature scenes shot from
two or more angles—check the disc box for
details.
When a multi-angle scene is playing, a
icon appears on screen to let you know that
other angles are available (this can be
switched off if you prefer—see Angle Indicator
on page 56).
1 During playback (or when paused),
press ANGLE to switch angle.
Displaying disc information
Various track, chapter and title information,
as well as the video transmission rate for DVD
discs, can be displayed on-screen while a disc
is playing.
1 To show/switch the information
displayed, press DISPLAY.
When a disc is playing, the information
appears at the top of the screen. Keep
pressing DISPLAY to change the displayed
information.
42
En
Play
Title
Current / Total
1/32
1
Audio Dolby Digital
Play
DVD-RW
Original
Elapsed
0.08
2/0CH
DVD-RW
Remain
30.22
--
Total
30.30
Subtitle
Original
Current / Total
Chapter
1/1
Tr. Rate
4.3Mbps
• CD and Video CD/Super VCD displays
Play
Track
Current / Total
2/16
Play
CD
Elapsed
1.07
Remain
4.40
Total
5.47
Elapsed
28.00
Remain
30.20
Total
58.20
CD
Disc
• WMA/MP3 disc displays
Play
Track
Current / Total
1/17
MP3
Elapsed
0.18
Track Name
Outernational
Play
MP3
Current / Total
Folder
2/7
Folder Name ACP
Remain
12.42
Total
13.00
DV260.book 43 ページ 2003年1月28日 火曜日 午後7時20分
Playing discs
05
• JPEG disc displays
Play
JPEG
Current / Total
File
1/40
File Name
FL000001
Play
JPEG
Current / Total
Folder
1/40
Folder Name Holiday
• You can see disc information (number of
titles/chapters, tracks, folders and so on)
from the Disc Navigator screen. See
Using the Disc Navigator to browse the
contents of a disc on page 32.
43
En
DV260.book 44 ページ 2003年1月28日 火曜日 午後7時20分
06
Viewing JPEG discs
Chapter 6
Viewing JPEG discs
Viewing JPEG discs
After loading a CD/CD-R/RW containing
JPEG pictures, press to start a slideshow
from the first folder/picture on the disc. The
player displays the pictures in each folder in
alphabetical order.
Pictures are automatically adjusted so that
they fill as much of the screen as possible (if
the aspect ratio of the picture is different to
your TV screen you may notice black bars at
the sides, or at the top and bottom of the
screen).
While the slideshow is running:
Button
What it does
Pauses the slideshow; press again
to restart.
Displays the previous picture.
Displays the next picture.
ANGLE
Pauses the slideshow and rotates
the currently displayed picture 90º
clockwise. Press (play) to restart
slideshow).
ZOOM
Pauses the slideshow and zooms
the screen (see below). Press (play) to restart slideshow).
MENU
44
En
• The , ANGLE and ZOOM buttons do not
work while the display shows LOADING.
• The time it takes for the player to load a file
increases with large file sizes.
• Up to 999 files are viewable on a disc. If
there are more files than this on a disc,
only the first 999 files are viewable.
Using the JPEG Disc Navigator
and Photo Browser
Use the JPEG Disc Navigator to find a particular folder or picture by filename; use the
Photo Browser to find a picture within a folder
by thumbnail image.
1 Press MENU to display the Disc Navigator screen.
Disc Navigator
Folder 1-2
Displays the Disc Navigator screen
(see below).
JPEG
001. F_001
002. F_002
File 1-40
001. FL000001
002. FL000002
003. FL000003
004. FL000004
005. FL000005
006. FL000006
007. FL000007
008. FL000008
The left column shows the folders on the disc,
the right column shows the files in a folder.
2 Use the cursor buttons (///) to
navigate.
When a file is highlighted, a thumbnail image
is displayed.
DV260.book 45 ページ 2003年1月28日 火曜日 午後7時20分
06
Viewing JPEG discs
• When a folder is highlighted you can
press ENTER to open the Photo Browser
screen for that folder. See below for more
on using the Photo Browser.
3 To resume the slideshow from the
highlighted file, press ENTER.
Using the Photo Browser
The Photo Browser displays nine thumbnail
images at a time from the current folder.
1 From the Disc Navigator screen, highlight a folder to display then press ENTER.
The Photo Browser screen opens with the first
nine pictures displayed as thumbnails.
Photo Browser
2 / 40
Zooming the screen
Using the zoom feature you can magnify a
part of the screen by a factor of 2 or 4, while
viewing pictures from a JPEG disc.
1 During slideshow playback, use the
ZOOM button to select the zoom factor.
• Normal
• 2x
• 4x
Normal
Live at Soft
Zoom 2x
Zoom 4x
2 Use the cursor buttons (///) to
highlight a thumbnail picture.
• Use the track skip buttons ( and )
to see the previous / next page of thumbnails. Keep the button pressed if you want
to skip several pages; release when you
reach the page you want.
• To return to the Disc Navigator screen,
press RETURN.
3 Press ENTER to display the selected
thumbnail full size on screen.
The slideshow resumes from the selected
picture.
• The slideshow is paused when the screen
is zoomed.
• Since JPEG pictures have a fixed resolution, picture quality may deteriorate, especially at 4x zoom. This is not a
malfunction.
2 Use the cursor buttons (///) to
change the zoomed area.
You can change the zoom factor and the
zoomed area freely.
• When you change the zoom area, this
becomes the new ‘default’ zoom area for
the disc loaded.
3 To resume the slideshow, press (play).
45
En
DV260.book 46 ページ 2003年1月28日 火曜日 午後7時20分
07
Audio Settings menu
Chapter 7
Audio Settings menu
Audio DRC
3 Press ENTER to make the setting and
exit the Audio Settings screen.
• Default setting: Off
When watching Dolby Digital DVDs at low
volume, it’s easy to lose the quieter sounds
completely—including some of the dialog.
Switching Audio DRC (Dynamic Range
Control) to On can help by bringing up the
quieter sounds, while controlling loud peaks.
How much of a difference you hear depends
on the material you’re listening to. If the material doesn’t have wide variations in volume,
you may not notice much change.
1 Press HOME MENU and select ‘Audio
Settings’ from the on-screen display.
Audio Settings
Video Adjust
Play Mode
Disc Navigator
Setup Navigator
2 Highlight Audio DRC, then use the
/ (cursor left/right) buttons to change
to ‘On’ or ‘Off’, as required.
Audio Settings
46
• The effect of Audio DRC depends on your
speakers and AV receiver settings.
• Default setting: Off
DVD
En
• Audio DRC is only effective through the
digital output when Digital Out (see
page 50) is set to On, and Dolby Digital
Out (see page 51) is set to Dolby Digital
> PCM.
Virtual Surround
HOME MENU
Initial Settings
• Audio DRC is only effective with Dolby
Digital audio sources.
Audio DRC
Off
Virtual Surround
Off
Switch on Virtual Surround to enjoy surround
sound effects from just two speakers.
When you play a Dolby Digital soundtrack,
TruSurround technology from SRS produces
a deep, realistic 3D soundspace from a pair of
stereo speakers. SRS TruSurround is a
process approved by Dolby Laboratories for
Virtual Dolby Digital sound.
DV260.book 47 ページ 2003年1月28日 火曜日 午後7時20分
Audio Settings menu
07
1 Press HOME MENU and select ‘Audio
Settings’ from the on-screen display.
HOME MENU
DVD
Audio Settings
Video Adjust
Play Mode
Disc Navigator
Initial Settings
Setup Navigator
2 Highlight Virtual Surround, then use
the / (cursor left/right) buttons to
change to ‘2V/SRS TruSurround’ or ‘Off’,
as required.
Audio Settings
Audio DRC
Off
Virtual Surround
Off
3 Press ENTER to make the setting and
exit the Audio Settings screen.
• You can also use the SURROUND button
on the remote control to switch Virtual
Surround on (2V/SRS TruSurround)/
Off.
• Virtual Surround doesn’t work with DTS or
96kHz linear PCM audio through either
the analog or digital outputs.
• If the player is outputting Dolby Digital or
MPEG bitstream audio (in other words, no
conversion to PCM), Virtual Surround has
no effect on the audio from the digital
output. See Digital Audio Out settings on
page 50 for how to set up the digital
output formats.
• How good the surround effect is varies
with the disc.
47
En
DV260.book 48 ページ 2003年1月28日 火曜日 午後7時20分
08
Video Adjust menu
Chapter 8
Video Adjust menu
Video Adjust
Creating your own presets
• Default setting: Standard
From the Video Adjust screen you can select
the standard video presentation or define
presets of your own.
1 Press HOME MENU and select ‘Video
Adjust’ from the on-screen display.
You can create up to three presets of your
own.
1 Select one of the Memory presets (see
above).
2 Press (cursor down) to select
‘Detailed Settings’ then press ENTER.
Video Adjust
HOME MENU
DVD
Memory1
Audio Settings
Video Adjust
Play Mode
Disc Navigator
Detailed Settings
3
Adjust the picture quality settings.
Setup Navigator
Initial Settings
Memory1
Recall Settings
2 Use the / (cursor left/right)
buttons to select a preset.
Memory1
Contrast
min
max
Brightness
min
min
max
max
Chroma Level
Video Adjust
Standard
• Use the / (cursor up/down) buttons to
select a setting.
• Standard – Normal
• Memory1–2 – Use for saving your own
presets (see below)
3 Press ENTER to make the setting and
exit the Video Adjust screen.
• Depending on the disc and the TV/
monitor, you may not see the effect
clearly.
48
En
• Use the / (cursor left/right) buttons
to adjust the current setting.
• Press DISPLAY to switch between full and
single view.
• You can change the preset number from
the Recall Settings menu item.
DV260.book 49 ページ 2003年1月28日 火曜日 午後7時20分
Video Adjust menu
08
You can adjust any or all of the following
picture quality settings:
• Contrast – Adjusts the contrast between
light and dark.
• Brightness – Adjusts the overall brightness.
• Chroma Level – Adjusts how saturated
colors appear.
4 Press ENTER to save the preset and
exit the Video Adjust screen.
49
En
DV260.book 50 ページ 2003年1月28日 火曜日 午後7時20分
09
Initial Settings menu
Chapter 9
Initial Settings menu
Using the Initial Settings
menu
Digital Audio Out settings
The Initial Settings menu gives you complete
control in setting up your DVD player,
including audio, and video output settings,
audience limitation settings, among others.
Digital Out
If an option is grayed out it means that it
cannot be changed at the current time. This is
usually because a disc is playing. Stop the
disc, then change the setting.
1 Press HOME MENU and select ‘Initial
Settings’ from the on-screen display.
You only need to make this setting if you
connected this player to an AV receiver (or other
component) using one of the digital outputs.
• Default setting: On
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Digital Out
Dolby Digital Out
DTS Out
96 kHz PCM Out
MPEG Out
On
Off
HOME MENU
DVD
Audio Settings
Video Adjust
Play Mode
Disc Navigator
Initial Settings
Setup Navigator
2 Select the setup category from the list
on the left, then select an item from the
menu list to the right.
3
Make the setting you want.
• The language options shown in the onscreen display illustrations on the
following pages may not correspond to
those available in your country or region.
50
En
If at any time you need to switch off the digital
audio output, set this to Off, otherwise leave
it On.
Note that you can’t switch on/off the optical
and coaxial outputs individually.
DV260.book 51 ページ 2003年1月28日 火曜日 午後7時20分
09
Initial Settings menu
Dolby Digital Out
96kHz PCM Out
You only need to make this setting if you
connected this player to an AV receiver (or other
component) using one of the digital outputs.
You only need to make this setting if you
connected this player to an AV receiver (or other
component) using one of the digital outputs.
• Default setting: Dolby Digital
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Initial Settings
Digital Out
Dolby Digital Out
DTS Out
96 kHz PCM Out
MPEG Out
Dolby Digital
Dolby Digital > PCM
If your AV receiver (or other connected
component) is Dolby Digital compatible, set
to Dolby Digital, otherwise set to Dolby
Digital > PCM.
DTS Out
You only need to make this setting if you
connected this player to an AV receiver (or other
component) using one of the digital outputs.
• Default setting: DTS
Digital Out
Dolby Digital Out
DTS Out
96 kHz PCM Out
MPEG Out
Digital Audio Out
Video Output
Language
Display
Options
Digital Out
Dolby Digital Out
DTS Out
96 kHz PCM Out
MPEG Out
96 kHz > 48kHz
96 kHz
If your AV receiver (or other connected
component) is compatible with high
sampling rates (96 kHz), set this to 96kHz,
otherwise set it to 96kHz > 48kHz (96 kHz
audio is converted to a more compatible 48
kHz). Check the manual that came with the
other component if you’re unsure whether it
is 96 kHz compatible.
MPEG Out
You only need to make this setting if you
connected this player to an AV receiver (or other
component) using one of the digital outputs.
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
• Default setting: 96kHz > 48kHz
DTS
Off
If your AV receiver (or other connected
component) has a built-in DTS decoder, set
this to DTS, otherwise set to Off. Check the
manual that came with the other component
if you’re unsure whether it is DTS compatible.
• If you set to DTS with a non-DTS compatible amplifier, noise will be output when
you play a DTS disc.
• Default setting: MPEG > PCM
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Digital Out
Dolby Digital Out
DTS Out
96 kHz PCM Out
MPEG Out
MPEG
MPEG > PCM
If your AV receiver (or other connected
component) is compatible with MPEG audio,
set this to MPEG, otherwise set it to MPEG >
PCM (MPEG audio is converted to more
compatible PCM audio). Check the manual
that came with the other component if you’re
unsure whether it is MPEG audio compatible.
51
En
DV260.book 52 ページ 2003年1月28日 火曜日 午後7時20分
09
Initial Settings menu
Video Output settings
Component Out
TV Screen
You only need to make this setting if you
connected this player to a progressive scan
compatible TV using the component video
outputs.
• Default setting: 4:3 (Letter Box)
• Default setting: Interlace
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
TV Screen
Component Out
S-Video Out
4:3 (Letter Box)
4:3 (Pan&Scan)
16:9 (Wide)
If you have a widescreen TV, select the 16:9
(Wide) setting—widescreen DVD software is
then shown using the full screen area. When
playing software recorded in conventional
(4:3) format, the settings on your TV will determine how the material is presented—see the
manual that came with your TV for details on
what options are available.
If you have a conventional TV, select either 4:3
(Letter Box) or 4:3 (Pan & Scan). In Letter
Box mode, widescreen software is shown with
black bars at the top and bottom of the
screen. Pan & Scan chops the sides off widescreen material to make it fit the 4:3 screen
(so even though the image looks larger on the
screen, you’re actually seeing less of the
picture). See also Screen sizes and disc
formats on page 62.
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
TV Screen
Component Out
Progressive
Interlace
S-Video Out
If you have a progressive-scan compatible TV,
set this to Progressive for flicker-free video
output. If your TV is not compatible with
progressive-scan video, set to Interlace.
Check the operating instructions that came
with your TV if you’re unsure about its
compatibility.
• When setting to Progressive, you have to
press ENTER once more to confirm. See
also below for important information on
progressive scan video.
About progressive scan video
Compared to interlace video, progressive
scan video effectively doubles the scanning
rate of the picture, resulting in a very stable,
flicker-free image. Progressive scan video is
available only from the component video
output.
• Taiwan model and when TV system is set
to AUTO or NTSC only: When Component Out (see above) is set to Progressive, there is no video output from the
VIDEO OUT (composite) and S (S-video)
52
En
DV260.book 53 ページ 2003年1月28日 火曜日 午後7時20分
09
Initial Settings menu
jacks. If you want to display video on more
than one monitor simultaneously, make
sure that it is set to Interlace. See also
Setting the TV system on page 68.
• If you connect a TV that is not compatible
with a progressive scan signal and switch
the player to progressive, you will not be
able to see any picture at all. In this case,
switch everything off and reconnect using
the supplied video cable (see Easy
connections on page 12), then switch
back to Interlace. Switch the player to
standby then, using the front panel
controls, press STANDBY/ON while
pressing to switch the player
back to Interlace.
STANDBY/ON
525p DVD PLAYER, PLEASE CONTACT OUR
CUSTOMER SERVICE CENTER.
This player is compatible with the following
Pioneer displays and monitors: PDP-503HDG,
PDP-433HDG progressive scan-compatible
TVs.
S-Video Out
You only need to make this setting if you
connected this player to your TV using an Svideo cable.
• Default setting: S2
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
TV Screen
Component Out
S-Video Out
S1
S2
FL DIMMER
STANDBY/ON
DV-366-S/ DV-366-K
If you find that the picture is stretched or
distorted on the default S2 setting, try
changing it to S1.
• Taiwan model and when TV system is set
to AUTO or NTSC only: When set to
Progressive, PAL and NTSC discs are
both output as progressive NTSC video.
See page 68.
• When TV System is set to PAL only:
Progressive cannot be selected. See
page 68.
Compatibility of this unit with
progressive-scan TVs.
This player is compatible with progressive
video Macro Vision System Copy Guard.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE
OF 525 PROGRESSIVE SCAN PICTURE PROBLEMS, IT
IS RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE “STANDARD DEFINITION”
OUTPUT. IF THERE ARE QUESTIONS REGARDING
OUR TV SET COMPATIBILITY WITH THIS MODEL
53
En
DV260.book 54 ページ 2003年1月28日 火曜日 午後7時20分
09
Initial Settings menu
Language settings
• Discs with two or more audio languages
usually allow you to select the audio
language from the disc menu. Press
MENU to access the disc menu.
Audio Language
• Default setting: English
Subtitle Language
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
• Default setting: English
Audio Language
Subtitle Language
DVD Menu Lang.
Subtitle Display
English
French
Spanish
Chinese
Other Language
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Audio Language
Subtitle Language
DVD Menu Lang.
Subtitle Display
English
French
Spanish
Chinese
Other Language
Taiwanese model only: Chinese
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Taiwanese model only: Chinese
Audio Language
Subtitle Language
DVD Menu Lang.
Subtitle Display
Chinese
English
Other Language
This setting is your preferred audio language
for DVD discs. If the language you specify
here is recorded on a disc, the player automatically plays the disc in that language.
The DVD format recognizes 136 different
languages. Select Other Language if you
want to specify a language other than those
listed. See also Selecting languages using the
language code list on page 64.
• You can switch between the languages
recorded on a DVD disc during playback
using the AUDIO button. (This does not
affect this setting.) See Switching DVD
audio language on page 40.
• Some DVD discs set the audio language
automatically when loaded, overriding the
Audio Language setting.
54
En
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Audio Language
Subtitle Language
DVD Menu Lang.
Subtitle Display
Chinese
English
Other Language
This setting is your preferred subtitle
language for DVD discs. If the language you
specify here is recorded on a disc, the player
automatically plays the disc with those subtitles.
The DVD format recognizes 136 different
languages. Select Other Language if you
want to specify a language other than those
listed. See also Selecting languages using the
language code list on page 64.
DV260.book 55 ページ 2003年1月28日 火曜日 午後7時20分
09
Initial Settings menu
• You can change or switch off the subtitles
on a DVD disc during playback using the
SUBTITLE button. (This does not affect
this setting.) See Switching subtitles on
page 40.
• Some DVD discs set the subtitle language
automatically when loaded, overriding the
Subtitle Language setting.
• Discs with two or more subtitle
languages usually allow you to select the
subtitle language from the disc menu.
Press MENU to access the disc menu.
DVD Menu Language
• Default setting: w/Subtitle Lang.
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Audio Language
Subtitle Language
DVD Menu Lang.
Subtitle Display
The DVD format recognizes 136 different
languages. Select Other Language if you
want to specify a language other than those
listed. See also Selecting languages using the
language code list on page 64.
Subtitle Display
• Default setting: On
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Audio Language
Subtitle Language
DVD Menu Lang.
Subtitle Display
On
Off
When set to On, the player displays subtitles
according to the Subtitle Language setting.
Set to Off to switch subtitles off altogether.
w/Subtitle Lang.
English
French
Spanish
Chinese
Other Language
Taiwanese model only
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Audio Language
Subtitle Language
DVD Menu Lang.
Subtitle Display
w/Subtitle Lang.
Chinese
English
Other Language
Some multilingual discs have disc menus in
several languages. This setting specifies in
which language the disc menus should
appear. Leave on the default setting for
menus to appear in the same language as
your Subtitle Language—see above.
55
En
DV260.book 56 ページ 2003年1月28日 火曜日 午後7時20分
09
Initial Settings menu
Display settings
Angle Indicator
• Default setting: On
OSD Language
Initial Settings
• Default setting: English
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
OSD Language
On Screen Display
Angle Indicator
English
français
Español
Initial Settings
OSD Language
On Screen Display
Angle Indicator
English
This sets the language of this player’s onscreen displays.
On Screen Display
• Default setting: On
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
OSD Language
On Screen Display
Angle Indicator
On
Off
This sets whether operation displays are
shown on-screen (Play, Resume, Scan and so
on.)
56
En
OSD Language
On Screen Display
Angle Indicator
On
Off
If you prefer not to see the camera icon onscreen during multi-angle scenes on DVD
discs, change this setting to Off.
Taiwanese model only:
Digital Audio Out
Video Output
Language
Display
Options
Digital Audio Out
Video Output
Language
Display
Options
DV260.book 57 ページ 2003年1月28日 火曜日 午後7時20分
09
Initial Settings menu
Options
1
Select ‘Password’.
Initial Settings
Parental Lock
Digital Audio Out
Video Output
Language
Display
Options
• Default level: Off
• Default password: none
• Default Country code: us (2119)
Some DVD-Video discs feature a Parental
Lock level. If your player is set to a lower level
than the disc, the disc won’t play. This gives
you some control about what your children
watch on your DVD player.
• Not all discs that you may consider inappropriate for your children use the
Parental Lock feature. These discs will
always play without requiring the password first.
• If you forget your password, you’ll need to
reset the player to its factory settings (see
Resetting the player on page 63), then
register a new password.
Registering a new password
You must register a password before you can
change the Parental Lock level or enter a
Country code.
Password
Level Change
Country Code
2 Use the number buttons to enter a 4digit password.
Initial Settings
Some discs also support the Country code
feature. The player does not play certain
scenes on these discs, depending on the
Country code you set.
Before you can set the Parental Lock level or
the Country code you must register a password. As the password owner, you can
change the Parental Lock level or Country
code whenever you like. You can also change
the password.
Parental Lock
PhotoViewer
Digital Audio Out
Video Output
Language
Display
Options
Parental Lock: Register Code Number
* * * *
The numbers you enter show up as asterisks
(*) on-screen.
3 Press ENTER to register the password
and return to the Options menu screen.
If you forget your password, you can reset the
player then register a new one. See Resetting
the player on page 63 for how to reset the
player.
Changing your password
To change your password, confirm your
existing password then enter a new one.
1
Select ‘Password Change’.
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Parental Lock
PhotoViewer
Password Change
Level Change
Country Code
57
En
DV260.book 58 ページ 2003年1月28日 火曜日 午後7時20分
09
Initial Settings menu
2 Use the number buttons to enter your
existing password, then press ENTER.
The numbers appear as asterisks as you enter
them.
2 Use number buttons to enter your
password, then press ENTER.
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Parental Lock: Password Change
Password
* * * *
* * * *
1 2 3 4 5 6 7 8 off
Enter a new password.
Select a new level.
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Password
New Password
3
3
Parental Lock : Level Change
Parental Lock: Password Change
Password
* * * *
New Password
* * * *
4 Press ENTER to register the new password and return to the Options menu
screen.
Parental Lock : Level Change
Password
* * * *
1 2 3 4 5 6 7 8 off
Press (cursor left) repeatedly to lock more
levels (more discs will require the password);
press (cursor right) to unlock levels. You
can’t lock level 1.
4 Press ENTER to set the new level and
return to the Options menu screen.
Setting/changing the Parental Lock level
1
Setting/changing the Country code
Select ‘Level Change’.
You may also want to refer to the Country code
list on page 65.
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Parental Lock
PhotoViewer
Password Change
Level Change
Country Code
1
Select ‘Country Code’.
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
58
En
Parental Lock
PhotoViewer
Password Change
Level Change
Country Code
DV260.book 59 ページ 2003年1月28日 火曜日 午後7時20分
09
Initial Settings menu
2 Use number buttons to enter your
password, then press ENTER.
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
•
Default setting: On
Initial Settings
Parental Lock: Country Code
Password
* * * *
Country Code List
Code
us
2 1 1 9
3 Select a Country code.
There are two ways you can do this.
• Select by code letter: Use / (cursor
up/down) to change the Country code.
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
PhotoViewer
Digital Audio Out
Video Output
Language
Display
Options
Parental Lock
PhotoViewer
On
Off
This setting is important if you load a disc that
contains both WMA/MP3 audio files and
JPEG picture files.
The default On setting allows you to view only
the JPEG files on this kind of disc. Set to Off
to be able to play the WMA/MP3 audio files.
Parental Lock: Country Code
Password
* * * *
Country Code List
Code
us
2 1 1 9
• Changing the PhotoViewer setting does
not take effect until the next disc is loaded
(or the current disc is reloaded).
• Select by code number: Press (cursor
right) then use the number buttons to
enter the 4-digit Country code (you can
find the Country code list on page 65.)
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Parental Lock: Country Code
Password
Country Code List
us
* * * *
Code
2 1 1 9
4 Press ENTER to set the new Country
code and return to the Options menu
screen.
• Changing the Country code does not take
effect until the next disc is loaded (or the
current disc is reloaded).
59
En
DV260.book 60 ページ 2003年1月28日 火曜日 午後7時20分
10
Additional information
Chapter 10
Additional information
Taking care of your player and
discs
Handling discs
When holding discs of any type, take care not
to leave fingerprints, dirt or scratches on the
disc surface. Hold the disc by its edge or by
the center hole and edge.
Damaged or dirty discs can affect playback
performance. Take care also not to scratch
the label side of the disc. Although not as
fragile as the recorded side, scratches can
still result in a disc becoming unusable.
Should a disc become marked with fingerprints, dust, etc., clean using a soft, dry cloth,
wiping the disc lightly from the center to the
outside edge as shown in the diagram below.
Wipe lightly from the center of the disc
using straight strokes.
If necessary, use a cloth soaked in alcohol, or
a commercially available CD/DVD cleaning kit
to clean a disc more thoroughly. Never use
benzine, thinner or other cleaning agents,
including products designed for cleaning
vinyl records.
Storing discs
Although CDs and DVD discs are more
durable than vinyl records, you should still
take care to handle and store discs correctly.
When you're not using a disc, return it to its
case and store upright. Avoid leaving discs in
excessively cold, humid, or hot environments
(including under direct sunlight).
Don't glue paper or put stickers onto the disc,
or use a pencil, ball-point pen or other sharptipped writing instrument. These could all
damage the disc.
For more detailed care information see the
instructions that come with discs.
Do not load more than one disc into the player
at a time.
Don’t wipe the disc surface using circular
strokes.
60
En
DV260.book 61 ページ 2003年1月28日 火曜日 午後7時20分
10
Additional information
Discs to avoid
Cleaning the pickup lens
Discs spin at high speed inside the player. If
you can see that a disc is cracked, chipped,
warped, or otherwise damaged, don't risk
using it in your player—you could end up
damaging it.
The DVD player’s lens should not become
dirty in normal use, but if for some reason it
should malfunction due to dust or dirt,
consult your nearest Pioneer-authorized
service center. Although lens cleaners for CD
players are commercially available, we do not
recommend using them since some may
damage the lens.
Problems with condensation
This player is designed for use with conventional, fully circular discs only. Use of shaped
discs is not recommended for this product.
Pioneer disclaims all liability arising in
connection with the use of shaped discs.
Cleaning the unit’s exterior
• Use a polishing cloth or dry cloth to wipe
off dust and dirt. If the surfaces are very
dirty, wipe with a soft cloth dipped in
some neutral cleanser diluted five or six
times with water and wrung out well, then
wipe again with a dry cloth.
• Do not use furniture wax or cleaners.
Never use thinners, benzine or insecticide
sprays or other chemicals on or near this
unit since they will corrode the surfaces.
• If you use a chemical-impregnated
cleaning cloth, read the instructions carefully before use. These cloths may leave
smear marks on half-mirror finish
surfaces; if this happens, finish with a dry
cloth.
• Unplug the unit when cleaning.
Condensation may form inside the player if it
is brought into a warm room from outside, or
if the temperature of the room rises quickly.
Although the condensation won’t damage the
player, it may temporarily impair its performance. For this reason you should leave it to
adjust to the warmer temperature for about
an hour before switching on and using.
Hints on installation
We want you to enjoy using this product for
years to come, so please bear in mind the
following points when choosing a suitable
location for it:
Do...
• Use in a well-ventilated room.
• Place on a solid, flat, level surface, such
as a table, shelf or stereo rack.
Don’t...
• Use in a place exposed to high temperatures or humidity, including near radiators and other heat-generating
appliances.
• Place on a window sill or other place
where the player will be exposed to direct
sunlight.
• Use in an excessively dusty or damp environment.
61
En
DV260.book 62 ページ 2003年1月28日 火曜日 午後7時20分
10
Additional information
• Place directly on top of an amplifier, or
other component in your stereo system
that becomes hot in use.
Screen sizes and disc formats
• Use near a television or monitor as you
may experience interference—especially
if the television uses an indoor antenna.
DVD-Video discs come in several different
screen aspect ratios, ranging from TV
programs, which are generally 4:3, to CinemaScope widescreen movies, with an aspect
ratio of up to about 7:3.
• Use in a kitchen or other room where the
player may be exposed to smoke or steam.
Televisions, too, come in different aspect
ratios; ‘standard’ 4:3 and widescreen 16:9.
• Use on a thick rug or carpet, or cover with
cloth—this may prevent proper cooling of
the unit.
Widescreen TV users
• Place on an unstable surface, or one that
is not large enough to support all four of
the unit’s feet.
Moving the player
If you need to move the player, first press
STANDBY/ON on the front panel to turn
the player off. Wait for -OFF- to disappear
from the display, then unplug the power
cable. Never lift or move the unit during playback—discs rotate at a high speed and may
be damaged.
If you have a widescreen TV, the TV Screen
setting (page 52) of this player should be set
to 16:9 (Wide).
When you watch discs recorded in 4:3 format,
you can use the TV controls to select how the
picture is presented. Your TV may offer
various zoom and stretch options; see the
instructions that came with your TV for
details.
Please note that some movie aspect ratios are
wider than 16:9, so even though you have a
widescreen TV, these discs will still play in a
‘letter box’ style with black bars at the top and
bottom of the screen.
Power cable caution
Handle the power cable by the plug part. Do
not pull out the plug by tugging the cable, and
never touch the power cable when your hands
are wet, as this could cause a short circuit or
electric shock. Do not place the unit, a piece
of furniture, or other object on the power
cable or pinch the cable in any other way.
Never make a knot in the cable or tie it with
other cables. The power cables should be
routed so that they are not likely to be stepped
on. A damaged power cable can cause a fire
or give you an electric shock. Check the power
cable once in a while. If you find it damaged,
ask your nearest Pioneer authorized service
center or your dealer for a replacement.
62
En
Standard TV users
If you have a standard TV, the TV Screen
setting (page 52) of this player should be set
to 4:3 (Letter Box) or 4:3 (Pan&Scan),
depending on which you prefer.
Set to 4:3 (Letter Box), widescreen discs are
shown with black bars top and bottom.
DV260.book 63 ページ 2003年1月28日 火曜日 午後7時20分
10
Additional information
Set to 4:3 (Pan&Scan), widescreen discs are
shown with the left and right sides cropped.
Although the picture looks larger, you don’t
actually see the whole picture.
Titles, chapters and tracks
DVD discs are generally divided into one or
more titles. Titles may be further subdivided
into chapters.
Title 1
Title 2
Title 3
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 1 Chapter 2
CDs and Video CD/Super VCDs are divided
into tracks.
Track 1
Use this procedure to reset all the player’s
settings to the factory default.
1
Track 5
Folder A
Track 1
Track 2
Track 3
Track 6
Folder B
Folder C
Track 1
File 1
.jpg
.jpg
.mp3
.mp3
Resetting the player
Track 3 Track 4
CD-ROMs contain folders and files. MP3 and
WMA files are referred to as tracks. Folders
may contain further folders.
.mp3
• Using the 16:9 (Wide) setting with a standard 4:3 TV, or either of the 4:3 settings
with a widescreen TV, will result in a
distorted picture.
Track 2
.mp3
Please note that many widescreen discs override the player’s settings so that the disc is
shown in letter box format regardless of the
setting.
File 2
Switch the player into standby.
2 Using the front panel buttons,
hold down the (stop) button and press
STANDBY/ON to switch the player back
on.
All the player’s settings are now reset, and
you should see the ‘Let’s Get Started’ screen.
63
En
DV260.book 64 ページ 2003年1月28日 火曜日 午後7時20分
10
Additional information
DVD-Video regions
All DVD-Video discs carry a region mark on
the case somewhere that indicates which
region(s) of the world the disc is compatible
with. Your DVD player also has a region mark,
which you can find on the rear panel. Discs
from incompatible regions will not play in this
player. Discs marked ALL will play in any
player.
The diagram below shows the various DVD
regions of the world.
1
5
2
6
2
1
3
4
5
2
4
Selecting languages using the
language code list
Some of the language options (such as ‘DVD
Language’ in the Setup Navigator) allow you
to set your prefered language from any of the
136 languages listed in the language code list
on page 65.
1
Select ‘Other Language’.
2 Use the / (cursor left/right)
buttons to select either a code letter or a
code number.
3 Use the / (cursor up/down)
buttons to select a code letter or a code
number.
See Language code list on page 65 for a
complete list of languages and codes.
64
En
DV260.book 65 ページ 2003年1月28日 火曜日 午後7時20分
10
Additional information
Language code list
Language (Language code letter), Language code
Japanese (ja), 1001
English (en), 0514
French (fr), 0618
German (de), 0405
Italian (it), 0920
Spanish (es), 0519
Chinese (zh), 2608
Dutch (nl), 1412
Portuguese (pt), 1620
Swedish (sv), 1922
Russian (ru), 1821
Korean (ko), 1115
Greek (el), 0512
Afar (aa), 0101
Abkhazian (ab), 0102
Afrikaans (af), 0106
Amharic (am), 0113
Arabic (ar), 0118
Assamese (as), 0119
Aymara (ay), 0125
Azerbaijani (az), 0126
Bashkir (ba), 0201
Byelorussian (be), 0205
Bulgarian (bg), 0207
Bihari (bh), 0208
Bislama (bi), 0209
Bengali (bn), 0214
Tibetan (bo), 0215
Breton (br), 0218
Catalan (ca), 0301
Corsican (co), 0315
Czech (cs), 0319
Welsh (cy), 0325
Danish (da), 0401
Bhutani (dz), 0426
Esperanto (eo), 0515
Estonian (et), 0520
Basque (eu), 0521
Persian (fa), 0601
Finnish (fi), 0609
Fiji (fj), 0610
Faroese (fo), 0615
Frisian (fy), 0625
Irish (ga), 0701
Scots-Gaelic (gd), 0704
Galician (gl), 0712
Guarani (gn), 0714
Gujarati (gu), 0721
Hausa (ha), 0801
Hindi (hi), 0809
Croatian (hr), 0818
Hungarian (hu), 0821
Armenian (hy), 0825
Interlingua (ia), 0901
Interlingue (ie), 0905
Inupiak (ik), 0911
Indonesian (in), 0914
Icelandic (is), 0919
Hebrew (iw), 0923
Yiddish (ji), 1009
Javanese (jw), 1023
Georgian (ka), 1101
Kazakh (kk), 1111
Greenlandic (kl), 1112
Cambodian (km), 1113
Kannada (kn), 1114
Kashmiri (ks), 1119
Kurdish (ku), 1121
Kirghiz (ky), 1125
Latin (la), 1201
Lingala (ln), 1214
Laothian (lo), 1215
Lithuanian (lt), 1220
Latvian (lv), 1222
Malagasy (mg), 1307
Maori (mi), 1309
Macedonian (mk), 1311
Malayalam (ml), 1312
Mongolian (mn), 1314
Moldavian (mo), 1315
Marathi (mr), 1318
Malay (ms), 1319
Maltese (mt), 1320
Burmese (my), 1325
Nauru (na), 1401
Nepali (ne), 1405
Norwegian (no), 1415
Occitan (oc), 1503
Oromo (om), 1513
Oriya (or), 1518
Panjabi (pa), 1601
Polish (pl), 1612
Pashto, Pushto (ps), 1619
Quechua (qu), 1721
Rhaeto-Romance (rm), 1813
Kirundi (rn), 1814
Romanian (ro), 1815
Kinyarwanda (rw), 1823
Sanskrit (sa), 1901
Sindhi (sd), 1904
Sangho (sg), 1907
Serbo-Croatian (sh), 1908
Sinhalese (si), 1909
Slovak (sk), 1911
Slovenian (sl), 1912
Samoan (sm), 1913
Shona (sn), 1914
Somali (so), 1915
Albanian (sq), 1917
Serbian (sr), 1918
Siswati (ss), 1919
Sesotho (st), 1920
Sundanese (su), 1921
Swahili (sw), 1923
Tamil (ta), 2001
Telugu (te), 2005
Tajik (tg), 2007
Thai (th), 2008
Tigrinya (ti), 2009
Turkmen (tk), 2011
Tagalog (tl), 2012
Setswana (tn), 2014
Tonga (to), 2015
Turkish (tr), 2018
Tsonga (ts), 2019
Tatar (tt), 2020
Twi (tw), 2023
Ukrainian (uk), 2111
Urdu (ur), 2118
Uzbek (uz), 2126
Vietnamese (vi), 2209
Volapük (vo), 2215
Wolof (wo), 2315
Xhosa (xh), 2408
Yoruba (yo), 2515
Zulu (zu), 2621
Country code list
Country, Country code, Country code letter
Argentina, 0118, ar
Australia, 0121, au
Austria, 0120, at
Belgium, 0205, be
Brazil, 0218, br
Canada, 0301, ca
Chile, 0312, cl
China, 0314, cn
Denmark, 0411, dk
Finland, 0609, fi
France, 0618, fr
Germany, 0405, de
Hong Kong, 0811, hk
India, 0914, in
Indonesia, 0904, id
Italy, 0920, it
Japan, 1016, jp
Korea, Republic of, 1118, kr
Malaysia, 1325, my
Mexico, 1324, mx
Netherlands, 1412, nl
New Zealand, 1426, nz
Norway, 1415, no
Pakistan, 1611, pk
Philippines, 1608, ph
Portugal, 1620, pt
Russian Federation, 1821, ru
Singapore, 1907, sg
Spain, 0519, es
Sweden, 1905, se
Switzerland, 0308, ch
Taiwan, 2023, tw
Thailand, 2008, th
United Kingdom, 0702, gb
USA, 2119, us
65
En
DV260.book 66 ページ 2003年1月28日 火曜日 午後7時20分
10
Additional information
Glossary
Analog audio
An electrical signal that directly represents
sound. Compare this to digital audio which
can be an electrical signal, but is an indirect
representation of sound. See also Digital
audio.
DRM
DRM (digital rights management) is a type of
server software developed to enable secure
distribution of paid content over the web,
recently incorporated by WMA (Windows
Media Audio ).
DTS
Aspect ratio
The width of a TV screen relative to its height.
Conventional TVs are 4:3 (in other words, the
screen is almost square); widescreen models
are 16:9 (the screen is almost twice as wide as
it is high).
Digital audio
An indirect representation of sound by
numbers. During recording, the sound is
measured at discrete intervals (44,100 times a
second for CD audio) by an analog-to-digital
converter, generating a stream of numbers.
On playback, a digital-to-analog converter
generates an analog signal based on these
numbers. See also Sampling frequency and
Analog audio.
Dolby Digital
1
Using a maximum of 5.1 channels of audio,
this high quality surround system is used in
many of the finer movie theaters around the
world.
The on-screen display shows which channels
are active, for example showing 3/2.1. The 3
being the two front channels and the center
channel; the 2 being the surround channels,
and the .1 being the LFE channel.
66
En
DTS stands for Digital Theater Systems. DTS
is a surround system different from Dolby
Digital that has become a popular surround
sound format for movies.
Dynamic range
The difference between the quietest and
loudest sounds possible in an audio signal
(without distorting or getting lost in noise).
Dolby Digital and DTS soundtracks are
capable of a very wide dynamic range, delivering dramatic cinema-like effects.
EXIF (Exchangeable Image File)
A file format developed by Fuji Photo Film for
digital still cameras. Digital cameras from
various manuafcturers use this compressed
file format which carries date, time and
thumbnail information, as well as the picture
data.
File extension
A tag added to the end of a filename to indicate the type of file. For example, “.mp3” indicates an MP3 file.
ISO 9660 format
International standard for the volume and file
structure of CD-ROM discs.
DV260.book 67 ページ 2003年1月28日 火曜日 午後7時20分
10
Additional information
JPEG
Regions (DVD-Video only)
A file format used for still images, such as
photographs and illustrations. JPEG files are
identified by the file extension “.jpg” or “.JPG”.
Most digital cameras use this format.
These associate discs and players with particular areas of the world. This unit will only play
discs that have compatible region codes. You
can find the region code of your unit by
looking on the rear panel. Some discs are
compatible with more than one region (or all
regions).
MP3
MP3 (MPEG1 audio layer 3) is a compressed
audio file format. Files are recognized by their
file extension “.mp3” or “.MP3”.
Sampling frequency
An audio format used on Video CD/Super
VCDs and some DVD discs. This unit can
convert MPEG audio to PCM format for wider
compatibility with digital recorders and AV
amplifiers. See also PCM (Pulse Code Modulation).
The rate at which sound is measured to be
turned into digital audio data. The higher the
rate, the better the sound quality, but the
more digital information is generated. Standard CD audio has a sampling frequency of
44.1kHz, which means 44,100 samples
(measurements) per second. See also Digital
audio.
MPEG video
WMA
MPEG audio
The video format used for Video CD/Super
VCDs and DVDs. Video CD/Super VCD uses
the older MPEG-1 standard, while DVD uses
the newer and much better quality MPEG-2
standard.
PBC (PlayBack Control) (Video CD/Super
VCD only)
A system of navigating a Video CD/Super VCD
through on-screen menus recorded onto the
disc. Especially good for discs that you would
normally not watch from beginning to end all
at once—karaoke discs, for example.
WMA is short for Windows Media Audio and
refers to an audio compression technology
developed by Microsoft Corporation. WMA
data can be encoded by using Windows
Media Player version 8 or Windows Media
Player for Windows XP. Files are recognized
by their file extension “.wma” or “.WMA”.
Microsoft, Windows Media, and the Windows
logo are trademarks, or registered trademarks of Microsoft Corporation in the United
States and/or other countries.
PCM (Pulse Code Modulation)
The most common system of encoding digital
audio, found on CDs and DAT. Excellent
quality, but requires a lot of data compared to
formats such as Dolby Digital and MPEG
audio. For compatibility with digital audio
recorders (CD, MD and DAT) and AV amplifiers with digital inputs, this unit can convert
Dolby Digital, DTS and MPEG audio to PCM.
See also Digital audio.
67
En
DV260.book 68 ページ 2003年1月28日 火曜日 午後7時20分
10
Additional information
Setting the TV system
(Except Taiwanese model)
The default setting of this player is AUTO, and
unless you notice that the picture is distorted
when playing some discs, you should leave it
set to AUTO. If you experience picture distortion with some discs, set the TV system to
match your country or region’s system. Doing
this, however, may restrict the kinds of disc
you can watch. The table below shows what
kinds of disc are compatible with each setting
(AUTO, PAL and NTSC).
1 If the player is on, press STANDBY/
ON to switch it to standby.
2 Using the front panel controls, hold
down then press STANDBY/ON
to switch the TV system.
The TV system changes as follows:
• AUTO NTSC
• NTSC PAL
• PAL AUTO
The player’s display shows “Welcome
Pioneer”, then indicates the new setting.
• You have to switch the player into standby
(press STANDBY/ON) before each
change.
Disc
Format NTSC
PAL
DVD
NTSC
NTSC
MOD.PAL NTSC
/Super VCD PAL
NTSC
PAL
Video CD
NTSC
NTSC
MOD.PAL NTSC
PAL
NTSC
PAL
PAL
—
NTSC
PAL
NTSC or
PAL
CD/no disc
68
En
Player setting
Type
AUTO
PAL
Watching NTSC on a PAL TV
(MOD. PAL)
Most models of the newly developed countdown PAL TV system detect 50 Hz (PAL)/60 Hz
(NTSC) and automatically switch vertical
amplitude, resulting in a display without
vertical shrinkage. However, in some cases,
the image may appear without color.
If your PAL TV does not have a V-Hold control,
you may not be able to watch NTSC discs
because of picture roll. If the TV has a V-Hold
control, adjust it until the picture stops
rolling.
On some TVs, the picture may shrink vertically, leaving black bands at the top and
bottom of the screen. This is not a malfunction; it is caused by the NTSC to PAL conversion.
DV260.book 69 ページ 2003年1月28日 火曜日 午後7時20分
10
Additional information
Taiwanese model only:
Changing the on-screen
display language to English
4
Press ENTER.
English
1 Press HOME MENU.
The on-screen display (OSD) appears.
HOME MENU
DVD
5 Use the / (cursor up/down)
buttons to select ‘English ’ from the list on
the right, then press ENTER.
2 Use the /// (cursor up/down/
left/right) buttons to select ‘
’
from the on-screen display, then press
ENTER.
HOME MENU
English
6
Press SETUP.
DVD
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
OSD Language
On Screen Display
Angle Indicator
English
3 Use the / (cursor up/down)
buttons to select ‘
’ from the list on
the left, then press ENTER.
69
En
DV260.book 70 ページ 2003年1月28日 火曜日 午後7時20分
10
Additional information
Specifications
Audio output (1 stereo pair)
General
Output level . . . . . . . . . . . . .During audio output
200 mVrms (1 kHz, –20 dB)
Number of channels . . . . . . . . . . . . . . . . . . . . . . 2
Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA jack
System . . . . . . . . . . . . . . . . . . . . . . . . . DVD player
Taiwanese model . . . . . . . . . . . . . . 110 V, 60 Hz
Other models . . . 110–127/220–240 V, 50/60 Hz
Power consumption
Taiwanese model . . . . . . . . . . . . . . . . . . . . 11 W
Other models . . . . . . . . . . . . . . . . . . . . . . . 12 W
Power consumption (standby)
Taiwanese model . . . . . . . . . . . . . . . . . . . .0.1 W
Other models . . . . . . . . . . . . . . . . . . . . . .0.18 W
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 kg
Dimensions:
DV-266-s. . . . . . . . 420 (W) x 53 (H) x 283 (D) mm
DV-366-s, DV-366-K, DV-466-s, DV-466-K
. . . . . . . . . . . . . . . 420 (W) x 55 (H) x 283 (D) mm
Operating temperature . . . . . . . .+5°C to +35°C
Operating humidity . . . . . . . . . . . . . . .5% to 85%
(no condensation)
Component video output
Y (luminance) - Output level . . . . . 1 Vp-p (75 Ω)
PB (color) - Output level . . . . . . . . 0.7 Vp-p (75 Ω)
PR (color) - Output level . . . . . . . . 0.7 Vp-p (75 Ω)
Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . .RCA jacks
D1/D2 video output (Taiwanese model
only)
Y (luminance) - Output level . . . . . 1 Vp-p (75 Ω)
PB (color) - Output level . . . . . . . . 0.7 Vp-p (75 Ω)
PR (color) - Output level . . . . . . . . 0.7 Vp-p (75 Ω)
Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . D terminal
Digital audio characteristics
Frequency response . . . . . . . . . . . 4 Hz to 44 kHz
(DVD fs: 96 kHz)
S/N ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 dB
Dynamic range. . . . . . . . . . . . . . . . . . . . . . 101 dB
Total harmonic distortion . . . . . . . . . . . 0.0016 %
Wow and flutter . . . . . . . . Limit of measurement
(±0.001% W. PEAK) or lower
Digital output
Optical digital output . . . . . . Optical digital jack
Coaxial digital output . . . . . . . . . . . . . . RCA jack
Accessories
Audio/video cable . . . . . . . . . . . . . . . . . . . . . . . . 1
Power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AA/R6P dry cell batteries . . . . . . . . . . . . . . . . . 2
Power cable (Central and South American
model). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Operating Instructions . . . . . . . . . . . . . . . . . . . . 2
Operating Instructions (Central and South
American model) . . . . . . . . . . . . . . . . . . . . . . . . . 3
Operating Instructions (Australian and PX
model). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Remote control overlay
(Taiwanese model only). . . . . . . . . . . . . . . . . . . . 1
S-video output
Y (luminance) - Output level . . . . . 1 Vp-p (75 Ω)
C (color) - Output level . . . . . . .286 mVp-p (75 Ω)
Jack . . . . . . . . . . . . . . . . . . . . . . . . . . S-video jack
• The specifications and design of this
product are subject to change without
notice, due to improvement.
Video output
Output level . . . . . . . . . . . . . . . . . . 1 Vp-p (75 Ω)
Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . .RCA jack
70
En
Published by Pioneer Corporation.
Copyright © 2003 Pioneer Corporation.
All rights reserved
DV260.book 71 ページ 2003年1月28日 火曜日 午後7時20分
Additional information
10
71
En
DV260.book 72 ページ 2003年1月28日 火曜日 午後7時20分
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90810-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: (905) 479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 656-472-1111
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270
K002E
<TSWZW/03A00001>
Printed in
<VRB1308-A>