Canon ELPH520HSRED Digital Camera User Manual

TOSHIBA
Satellite 2450 Series
Portable Personal Computer
User’s Manual
Copyright
© 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws,
this manual cannot be reproduced in any form without the prior written permission
of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
TOSHIBA Satellite 2450 Series Portable Personal Computer User’s Manual
First edition February 2003
Copyright authority for music, movies, computer programs, data bases
and other intellectual property covered by copyright laws belongs to the
author or to the copyright owner. Copyrighted material can be reproduced only for personal use or use within the home. Any other use
beyond that stipulated above (including conversion to digital format,
alteration, transfer of copied material and distribution on a network)
without the permission of the copyright owner is a violation of copyright
or author’s rights and is subject to civil damages or criminal action.
Please comply with copyright laws in making any reproduction from this
manual.
Disclaimer
This manual has been validated and reviewed for accuracy. The instructions and
descriptions it contains are accurate for the TOSHIBA Satellite 2450 Series Portable
Personal Computer at the time of this manual’s production. However, succeeding
computers and manuals are subject to change without notice. TOSHIBA assumes
no liability for damages incurred directly or indirectly from errors, omissions or
discrepancies between the computer and the manual.
Trademarks
Intel, Intel SpeedStep and Pentium are trademarks or registered trademarks of Intel
Corporation or its subsidiaries in the United States and other countries/regions.
Windows and Microsoft are registered trademarks of Microsoft Corporation.
Photo CD is a trademark of Eastman Kodak.
Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under
license.
iLINK is a trademark and Memory Stick is a registered trademark of Sony Corporation.
Compact Flash is a trademark of SunDisk Corporation.
FCC information
Product Name : Satellite 2450
Model number : PS245
FCC notice "Declaration of Conformity
Information"
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
❑
Reorient or relocate the receiving antenna.
❑
Increase the separation between the equipment and receiver.
❑
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
❑
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Only peripherals complying with the FCC class B limits may
be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in
interference to radio and TV reception. Shielded cables must be used
between the external devices and the computer’s external monitor port,
USB port, IEEE1394 port, parallel port and microphone jack. Changes
or modifications made to this equipment, not expressly approved by
TOSHIBA or parties authorized by TOSHIBA could void the user’s
authority to operate the equipment.
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
Contact
Address:
TOSHIBA America Information Systems, Inc.
9740 Irvine Boulevard
Irvine, California 92618-1697
Telephone: (949)583-3000
EU Declaration of Conformity information
TOSHIBA declares, that the product: PS245 conforms to the following Standards:
Supplementary Information:
“The product complies with the requirements
of the Low Voltage Directive 73/23/EEC, the
EMC Directive 89/336/EEC and/or the R&TTE
Directive 1999/05/EEC.”
This product is carrying the CE-Mark in accordance with the related European
Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8,
41460 Neuss, Germany.
VCCI Class B Information
Modem warning notice
Conformity Statement
The equipment has been approved to [Commission Decision “CTR21”] for panEuropean single terminal connection to the Public Switched Telephone Network
(PSTN).
However, due to differences between the individual PSTNs provided in different
countries/regions the approval does not, of itself, give an unconditional assurance
of successful operation on every PSTN network termination point.
In the event of problems, you should contact your equipment supplier in the first
instance.
Network Compatibility Statement
This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.
Germany
ATAAB AN005,AN006,AN007,AN009,AN010 and
DE03,04,05,08,09,12,14,17
Greece
ATAAB AN005,AN006 and GR01,02,03,04
Portugal
ATAAB AN001,005,006,007,011 and P03,04,08,10
Spain
ATAAB AN005,007,012, and ES01
Switzerland
ATAAB AN002
All other countries/regions ATAAB AN003,004
Specific switch settings or software setup are required for each network, please refer
to the relevant sections of the user guide for more details.
The hookflash (timed break register recall) function is subject to separate national
type approvals. It has not been tested for conformity to national type regulations,
and no guarantee of successful operation of that specific function on specific
national networks can be given.
Japan regulations
Region selection
If you are using the computer in Japan, technical regulations described in the
Telecommunications Business Law require that you select the Japan region mode. It
is illegal to use the modem in Japan with any other selection.
Redial
Up to two redial attempts can be made. If more than two redial attempts are made, the
modem will return Black Listed. If you are experiencing problems with the Black
Listed code, set the interval between redials at one minute or longer.
Japan’s Telecommunications Business Law permits up to two redials on analogue
telephones, but the redials must be made within a total of three minutes.
The internal modem is approved by Japan Approvals Institute for Telecommunications Equipment.
A02-0604JP
Pursuant to FCC CFR 47, Part 68:
When you are ready to install or use the modem, call your local telephone company
and give them the following information:
❑
The telephone number of the line to which you will connect the modem
❑
The registration number that is located on the device
The FCC registration number of the modem will be found on either the device which
is to be installed, or, if already installed, on the bottom of the computer outside of the
main system label.
❑
The Ringer Equivalence Number (REN) of the modem, which can vary. For the
REN of your modem, refer to your modem’s label.
The modem connects to the telephone line by means of a standard jack called the
USOC RJ11C.
Type of service
Your modem is designed to be used on standard-device telephone lines. Connection
to telephone company-provided coin service (central office implemented systems) is
prohibited. Connection to party lines service is subject to state tariffs. If you have
any questions about your telephone line, such as how many pieces of equipment you
can connect to it, the telephone company will provide this information upon request.
Telephone company procedures
The goal of the telephone company is to provide you with the best service it can. In
order to do this, it may occasionally be necessary for them to make changes in their
equipment, operations, or procedures. If these changes might affect your service or
the operation of your equipment, the telephone company will give you notice in
writing to allow you to make any changes necessary to maintain uninterrupted
service.
If problems arise
If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone
network. If the telephone company notes a problem, they may temporarily discontinue service. When practical, they will notify you in advance of this disconnection.
If advance notice is not feasible, you will be notified as soon as possible. When
you are notified, you will be given the opportunity to correct the problem and
informed of your right to file a complaint with the FCC. In the event repairs are ever
needed on your modem, they should be performed by TOSHIBA Corporation or an
authorized representative of TOSHIBA Corporation.
Disconnection
If you should ever decide to permanently disconnect your modem from its present
line, please call the telephone company and let them know of this change.
Fax branding
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person
to use a computer or other electronic device to send any message via a telephone
fax machine unless such message clearly contains in a margin at the top or bottom
of each transmitted page or on the first page of the transmission, the date and time it
is sent and an identification of the business, other entity or individual sending the
message and the telephone number of the sending machine or such business, other
entity or individual. In order to program this information into your fax modem, you
should complete the setup of your fax software before sending messages.
Instructions for IC CS-03 certified equipment
1 The Industry Canada label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network protective,
operational and safety requirements as prescribed in the appropriate Terminal
Equipment Technical Requirements document(s). The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection.
The customer should be aware that compliance with the above conditions may
not prevent degradation of service in some situations. Repairs to certified
equipment should be coordinated by a representative designated by the
supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system,
if present, are connected together. This precaution may be particularly important
in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority,
or electrician, as appropriate.
2 The user manual of analog equipment must contain the equipment’s Ringer
Equivalence Number (REN) and an explanation notice similar to the following:
The Ringer Equivalence Number (REN) of the modem, which can vary. For the
REN of your modem, refer to your modem’s label.
NOTICE: The Ringer Equivalence Number (REN) assigned to each
terminal device provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject
only to the requirement that the sum of the Ringer Equivalence Numbers
of all the devices does not exceed 5.
3 The standard connecting arrangement (telephone jack type) for this equipment is
jack type(s): USOC RJ11C.
The IC registration number of the modem is shown below.
Canada: 1353A-L4AINT
Notes for Users in Australia and New Zealand
Modem warning notice for Australia
Modems connected to the Australian telecoms network must have a valid Austel
permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia.
The use of other country/region setting while the modem is attached to the
Australian PSTN would result in you modem being operated in a non-compliant
manner. To verify that the country/region is correctly set, enter the command ATI
which displays the currently active setting.
To set the country/region permanently to Australia, enter the following command
sequence:
AT%TE=1
ATS133=1
AT&F
AT&W
AT%TE=0
ATZ
Failure to set the modem to the Australia country/region setting as shown above
will result in the modem being operated in a non-compliant manner. Consequently,
there would be no permit in force for this equipment and the Telecoms Act 1991
prescribes a penalty of $12,000 for the connection of non-permitted equipment.
Notes for use of this device in New Zealand
❑
The grant of a Telepermit for a device in no way indicates Telecom acceptance
of responsibility for the correct operation of that device under all operating
conditions. In particular the higher speeds at which this modem is capable of
operating depend on a specific network implementation which is only one of
many ways of delivering high quality voice telephony to customers. Failure to
operate should not be reported as a fault to Telecom.
❑
In addition to satisfactory line conditions a modem can only work properly if:
a/
it is compatible with the modem at the other end of the call and
b/
the application using the modem is compatible with the application at the
other end of the call - e.g., accessing the Internet requires suitable
software in addition to a modem.
❑
This equipment shall not be used in any manner which could constitute a
nuisance to other Telecom customers.
❑
Some parameters required for compliance with Telecom’s PTC Specifications
are dependent on the equipment (PC) associated with this modem. The
associated equipment shall be set to operate within the following limits for
compliance with Telecom Specifications:
a/
There shall be no more than 10 call attempts to the same number within
any 30 minute period for any single manual call initiation, and
b/
The equipment shall go on-hook for a period of not less than 30 seconds
between the end of one attempt and the beginning of the next.
c/
Automatic calls to different numbers shall be not less than 5 seconds
apart.
❑
Immediately disconnect this equipment should it become physically damaged,
and arrange for its disposal or repair.
❑
The correct settings for use with this modem in New Zealand are as follows:
ATB0 (CCITT operation)
AT&G2 (1800 Hz guard tone)
AT&P1 (Decadic dialing make-break ratio =33%/67%)
ATS0=0 (not auto answer)
ATS6=4 (Blind dial delay)
ATS7=less than 90 (Time to wait to carrier after dialing)
ATS10=less than 150 (loss of carrier to hangup delay, factory default of 15
recommended)
ATS11=90 (DTMF dialing on/off duration=90 ms)
ATX2 (Dial tone detect, but not (U.S.A.) call progress detect)
❑
When used in the Auto Answer mode, the S0 register must be set with a value
of 3 or 4. This ensures:
(a) a person calling your modem will hear a short burst of ringing before the
modem answers. This confirms that the call has been successfully
switched through the network.
(b) caller identification information (which occurs between the first and
second ring cadences) is not destroyed.
❑
The preferred method of dialing is to use DTMF tones (ATDT...) as this is
faster and more reliable than pulse (decadic) dialing. If for some reason you
must use decadic dialing, your communications program must be set up to
record numbers using the following translation table as this modem does not
implement the New Zealand “Reverse Dialing” standard.
Number to be dialed: 0 1 2 3 4 5 6 7 8 9
Number to program into computer: 0 9 8 7 6 5 4 3 2 1
Note that where DTMF dialing is used, the numbers should be entered
normally.
❑
The transmit level from this device is set at a fixed level and because of this
there may be circumstances where the performance is less than optimal. Before
reporting such occurrences as faults, please check the line with a standard
Telepermitted telephone, and only report a fault if the phone performance is
impaired.
❑
It is recommended that this equipment be disconnected from the Telecom line
during electrical storms.
❑
When relocating the equipment, always disconnect the Telecom line connection before the power connection, and reconnect the power first.
❑
This equipment may not be compatible with Telecom Distinctive Alert cadences and services such as FaxAbility.
NOTETHATFAULTCALLOUTSCAUSEDBYANYOFTHEABOVE
CAUSESMAYINCURACHARGEFROMTELECOM
General conditions
As required by PTC 100, please ensure that this office is advised of any changes to
the specifications of these products which might affect compliance with the relevant
PTC Specifications.
The grant of this Telepermit is specific to the above products with the marketing
description as stated on the Telepermit label artwork. The Telepermit may not be
assigned to other parties or other products without Telecom approval.
A Telepermit artwork for each device is included from which you may prepare any
number of Telepermit labels subject to the general instructions on format, size and
colour on the attached sheet.
The Telepermit label must be displayed on the product at all times as proof to
purchasers and service personnel that the product is able to be legitimately
connected to the Telecom network.
The Telepermit label may also be shown on the packaging of the product and in the
sales literature, as required in PTC 100.
The charge for a Telepermit assessment is $337.50. An additional charge of $337.50
is payable where an assessment is based on reports against non-Telecom New
Zealand Specifications. $112.50 is charged for each variation when submitted at the
same time as the original.
An invoice for $NZ1237.50 will be sent under separate cover.
Description on Laser specification
The optical drive such as CD-ROM drive, CD-RW drive, DVD-ROM drive, DVD/
CD-RW drive and DVD Multi drive that is used in this computer is equipped with
laser. The classification label with the following sentence is affixed to the surface of
the drive.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL A LASER DE CLASSE 1
KLASS 1 LASER APPARAT
The drive with the above label is certified by the manufacturer that the drive
complies with the requirement for laser product on the date of manufacturing
pursuant to article 21 of Code of Federal Regulations by the United States of
America, Department of Health & Human Services, Food and Drug Administration.
In other countries, the drive is certified to comply with the requirement pursuant to
IEC 825 and EN60825 on class 1 laser product.
This computer is equipped with the optical drive in the following list according to
the model.
Manufacturer
Type
TOSHIBA
SD-C2612
HITACHI
GDR-8081N
HITACHI
GDR-8082N
TEAC
DW-224E
Panasonic Communications
UJDA740
TOSHIBA
SD-R6012
Panasonic Communications
UJ-810
TEAC
DV-W22E
Table of Contents
Preface
Manual contents ............................................................................. xxiii
Conventions ..................................................................................... xxiv
Abbreviations ..................................................................................... xxiv
Icons ................................................................................................. xxiv
Keys ................................................................................................. xxiv
Key operation ..................................................................................... xxv
Display ............................................................................................... xxv
Messages .......................................................................................... xxv
General Precautions
Stress injury ................................................................................... xxvii
Heat injury ...................................................................................... xxvii
Pressure or impact damage ......................................................... xxvii
CPU performance disclaimer ...................................................... xxviii
PC card overheating .................................................................... xxviii
Chapter 1 Introduction
Equipment checklist .......................................................................... 1-1
Hardware ............................................................................................ 1-1
Software ............................................................................................. 1-1
Documentation ................................................................................... 1-2
Features ............................................................................................. 1-2
Special features ................................................................................. 1-8
Utilities .............................................................................................. 1-10
Options ............................................................................................. 1-11
Chapter 2 The Grand Tour
Front with the display closed ........................................................... 2-1
Left side .............................................................................................. 2-2
Right side ........................................................................................... 2-4
Back side ............................................................................................ 2-5
xv
Underside ........................................................................................... 2-7
Front with the display open .............................................................. 2-8
System indicators ............................................................................ 2-10
Keyboard indicators ........................................................................ 2-11
USB diskette drive ........................................................................... 2-12
Slim Select Bay modules ................................................................ 2-13
DVD-ROM drive ................................................................................ 2-13
CD-RW/DVD-ROM drive ................................................................... 2-14
DVD-R/-RW drive .............................................................................. 2-14
DVD Multi drive ................................................................................. 2-15
Slim Select Bay HDD adaptor (Black) .............................................. 2-16
TOSHIBA Style Bay Bridge media adaptor ....................................... 2-16
Universal AC adaptor ...................................................................... 2-17
Chapter 3 Getting Started
Setting up your work space .............................................................. 3-1
General conditions .............................................................................. 3-2
Placement of the computer ................................................................. 3-2
Seating and posture ........................................................................... 3-3
Lighting .............................................................................................. 3-4
Work habits ........................................................................................ 3-4
Connecting the Universal AC adaptor ............................................. 3-5
Opening the display .......................................................................... 3-6
Turning on the power ....................................................................... 3-6
Starting up for the first time .............................................................. 3-7
Turning off the power ....................................................................... 3-7
Shut Down mode (Boot mode) ............................................................ 3-7
Hibernation mode ............................................................................... 3-8
Standby mode .................................................................................. 3-10
Restarting the computer ................................................................. 3-11
Restoring the preinstalled software from the Product
Recovery CD-ROM ..................................................................... 3-12
Chapter 4 Operating Basics
Pointing devices ................................................................................ 4-1
Using the TouchPad ........................................................................... 4-1
Using the USB diskette drive ............................................................ 4-2
Connecting 3 1/2" diskette drive ......................................................... 4-2
Disconnecting 3 1/2" diskette drive ..................................................... 4-3
xvi
Changing Lifestyle Bay modules ..................................................... 4-3
Removing a module ............................................................................ 4-3
Installing a module .............................................................................. 4-4
Using optical media drives ............................................................... 4-5
Loading disks ..................................................................................... 4-5
Removing disks .................................................................................. 4-8
Writing CDs on CD-RW/DVD-ROM drive ........................................... 4-9
Before writing or rewriting .................................................................... 4-9
When writing or rewriting .................................................................. 4-10
Writing CDs on DVD-R/-RW drive ................................................... 4-11
Important message ........................................................................... 4-11
Disclaimer ........................................................................................ 4-11
Writing CDs on DVD Multi drive ...................................................... 4-12
Important message ........................................................................... 4-12
Disclaimer ........................................................................................ 4-12
Read/write function chart .................................................................. 4-13
Before writing or rewriting .................................................................. 4-15
When writing or rewriting .................................................................. 4-16
Drag'n Drop CD ................................................................................. 4-16
Data Verification ............................................................................... 4-17
Video (DVD-R/-RW/-RAM) ................................................................ 4-17
Media care ....................................................................................... 4-19
CD/DVDs .......................................................................................... 4-19
Diskettes .......................................................................................... 4-19
Modem .............................................................................................. 4-20
Region selection ............................................................................... 4-20
Properties menu ............................................................................... 4-21
Connecting ....................................................................................... 4-22
Disconnecting ................................................................................... 4-23
Wireless communications ............................................................... 4-23
Wireless LAN ................................................................................... 4-23
Security ............................................................................................ 4-24
Bluetooth wireless technology .......................................................... 4-24
Wireless communication switch ....................................................... 4-25
Wireless communication Indicator .................................................... 4-25
LAN ................................................................................................... 4-26
Connecting LAN cable ...................................................................... 4-26
Disconnecting LAN cable ................................................................. 4-27
Cleaning the computer ................................................................... 4-27
Moving the computer ...................................................................... 4-28
Heat dispersal .................................................................................. 4-28
xvii
Chapter 5 The Keyboard
Typewriter keys ................................................................................. 5-1
F1 … F12 function keys ..................................................................... 5-2
Soft keys: Fn key combinations ........................................................ 5-2
Emulating keys on enhanced keyboard .............................................. 5-2
Hot keys ............................................................................................. 5-4
Fn Sticky key ..................................................................................... 5-7
Windows special keys ....................................................................... 5-7
Keypad overlay .................................................................................. 5-7
Turning on the overlays ....................................................................... 5-7
Temporarily using normal keyboard (overlay on) .................................. 5-8
Temporarily using overlay (overlay off) ................................................. 5-9
Temporarily changing modes .............................................................. 5-9
Generating ASCII characters ............................................................ 5-9
Chapter 6 Power and Power-Up Modes
Power conditions ............................................................................... 6-1
Power indicators ............................................................................... 6-2
Battery indicator ................................................................................. 6-2
DC IN indicator ................................................................................... 6-3
Power indicator ................................................................................... 6-3
Battery types ...................................................................................... 6-3
Battery pack ....................................................................................... 6-3
Real Time Clock battery ..................................................................... 6-4
Care and use of the battery pack ..................................................... 6-5
Safety precautions .............................................................................. 6-5
Charging the batteries ........................................................................ 6-8
Monitoring battery capacity ................................................................ 6-9
Maximizing battery operating time .................................................... 6-10
Retaining data with power off ............................................................ 6-11
Extending battery life ........................................................................ 6-11
Replacing the battery pack ............................................................. 6-12
Removing the battery pack ............................................................... 6-12
Installing the battery pack ................................................................. 6-13
Starting the computer by password ............................................... 6-14
Power-up modes ............................................................................. 6-15
Windows utilities .............................................................................. 6-15
Hot keys ........................................................................................... 6-15
xviii
Panel power off ............................................................................... 6-15
System Auto Off ............................................................................... 6-15
Chapter 7 HW Setup and Passwords
HW Setup ........................................................................................... 7-1
Accessing HW Setup ......................................................................... 7-1
HW Setup window .............................................................................. 7-1
Supervisor password ......................................................................... 7-9
Chapter 8 Optional Devices
PC cards ............................................................................................. 8-2
Inserting a PC card ............................................................................. 8-2
Removing a PC card ........................................................................... 8-3
SD cards ............................................................................................. 8-4
Inserting an SD card .......................................................................... 8-4
Removing an SD card ......................................................................... 8-5
SD card care ...................................................................................... 8-5
Memory expansion ............................................................................ 8-6
Installing memory module ................................................................... 8-6
Removing memory module ................................................................ 8-11
TOSHIBA Style Bay Bridge media adaptor ................................... 8-12
Before installing ................................................................................ 8-13
SmartMedia ...................................................................................... 8-15
Memory Stick ................................................................................... 8-17
Compact Flash ................................................................................. 8-18
Bridge media care ............................................................................ 8-19
Battery pack (Black) ........................................................................ 8-19
Universal AC adaptor ...................................................................... 8-19
USB FDD kit ...................................................................................... 8-19
Slim Select Bay HDD adaptor (Black) ............................................ 8-20
External monitor .............................................................................. 8-21
TV ...................................................................................................... 8-22
Using the TV button .......................................................................... 8-22
Changing the resolution .................................................................... 8-22
i.LINK (IEEE1394) .............................................................................. 8-24
Precautions ...................................................................................... 8-24
Connecting ....................................................................................... 8-25
Disconnecting ................................................................................... 8-25
Security lock .................................................................................... 8-26
xix
Chapter 9 Troubleshooting
Problem solving process ................................................................... 9-1
Preliminary checklist .......................................................................... 9-1
Analyzing the problem ........................................................................ 9-2
Hardware and system checklist ........................................................ 9-3
System start-up .................................................................................. 9-3
Self test .............................................................................................. 9-4
Power ................................................................................................. 9-4
Password ........................................................................................... 9-7
Keyboard ............................................................................................ 9-7
LCD panel .......................................................................................... 9-7
Hard disk drive .................................................................................... 9-8
DVD-ROM drive .................................................................................. 9-9
CD-RW/DVD-ROM drive ................................................................... 9-10
DVD-R/-RW drive .............................................................................. 9-12
DVD Multi drive ................................................................................. 9-13
Diskette drive .................................................................................... 9-15
SD card ............................................................................................ 9-15
PC card ............................................................................................ 9-16
Infrared port ...................................................................................... 9-16
Pointing device ................................................................................. 9-17
USB ................................................................................................. 9-19
Memory expansion ........................................................................... 9-19
Sound system .................................................................................. 9-20
Monitor ............................................................................................. 9-20
i.LINK (IEEE1394) ............................................................................ 9-21
Modem ............................................................................................. 9-21
LAN .................................................................................................. 9-23
Wireless LAN ................................................................................... 9-23
Bluetooth .......................................................................................... 9-24
Real Time Clock ............................................................................... 9-24
TOSHIBA support ............................................................................. 9-25
Before you call ................................................................................. 9-25
Where to write .................................................................................. 9-25
xx
Appendixes
Appendix A
Specifications ................................................................................... A-1
Appendix B
Display Controller and Modes ......................................................... B-1
Appendix C
AT Commands .................................................................................. C-1
Appendix D
S-registers ......................................................................................... D-1
Appendix E
V.90 ..................................................................................................... E-1
Appendix F
Internal Modem Guide ...................................................................... F-1
Appendix G
Wireless LAN ..................................................................................... G-1
Appendix H
AC Power Cord and Connectors ...................................................... H-1
Appendix I
Parts Numbers .................................................................................... I-1
Glossary
Index
xxi
xxii
Preface
Congratulations on your purchase of the Satellite 2450 series computer. This
powerful notebook computer provides excellent expansion capability, including
multimedia devices, and it is designed to provide years of reliable, high-performance
computing.
This manual tells how to set up and begin using your Satellite 2450 series computer.
It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
If you are a new user of computers or if you’re new to portable computing, first read
over the Introduction and The Grand Tour chapters to familiarize yourself with the
computer’s features, components and accessory devices. Then read Getting Started
for step-by-step instructions on setting up your computer.
If you are an experienced computer user, please continue reading the preface to
learn how this manual is organized, then become acquainted with this manual by
browsing through its pages. Be sure to look over the Special features section of the
Introduction, to learn about features that are uncommon or unique to the computers
and carefully read HW Setup and Passwords.
Manual contents
This manual offers important information about your computer, including solutions
to the most common problems, and features and specifications. Refer to the Online
manual preinstalled on your system for the details. To open the Online manual,
follow either one of the steps below:
1. From Desk top, click Start, point to All programs, click TOSHIBA User's Manual.
2. From Desk top, click TOSHIBA Console icon, click Help? of the TOSHIBA
Console tab.
The Online manual is composed of the following nine chapters, a glossary and an
index.
Chapter 1, Introduction, is an overview of the computer’s features, capabilities, and
options.
Chapter 2, The Grand Tour, identifies the components of the computer and briefly
explains how they function.
Chapter 3, Getting Started, provides a quick overview of how to begin operating
your computer and gives tips on safety and designing your work area.
xxiii
User's Manual
Chapter 4, Operating Basics, includes instructions on using the following devices:
Touch Pad, Slim Select Bay modules, USB diskette drive, optical media drives,
audio/video controls, microphone, modem, wireless communication features, LAN.
It also provides tips on care of the computer, diskettes and CD/DVDs.
Chapter 5, The Keyboard, describes special keyboard functions including the
keypad overlay and hot keys.
Chapter 6, Power and Power-Up Modes, gives details on the computer’s power
resources and battery save modes.
Chapter 7, HW Setup and Passwords, explains how to configure the computer using
the HW Setup program. It also tells how to set a password.
Chapter 8, Optional Devices, describes the optional hardware available.
Chapter 9, Troubleshooting, suggests courses of action if the computer doesn’t
seem to be working properly.
The Appendixes provide technical information about your computer.
The Glossary defines general computer terminology and includes a list of acronyms
used in the text.
The Index quickly directs you to the information contained in this manual.
Conventions
This manual uses the following formats to describe, identify, and highlight terms
and operating procedures.
Abbreviations
On first appearance, and whenever necessary for clarity, abbreviations are enclosed
in parentheses following their definition. For example: Read Only Memory
(ROM). Acronyms are also defined in the Glossary.
Icons
Icons identify ports, dials, and other parts of your computer. The indicator panel
also uses icons to identify the components it is providing information on.
Keys
The keyboard keys are used in the text to describe many computer operations. A
distinctive typeface identifies the key top symbols as they appear on the keyboard.
For example, Enter identifies the Enter key.
xxiv
Conventions
Key operation
Some operations require you to simultaneously use two or more keys. We identify
such operations by the key top symbols separated by a plus sign (+). For example,
Ctrl + C means you must hold down Ctrl and at the same time press C. If three
keys are used, hold down the first two and at the same time press the third.
ABC
When procedures require an action such as clicking an icon or entering
text, the icon’s name or the text you are to type in is represented in the
type face you see to the left.
Display
ABC
Names of windows or icons or text generated by the computer that
appears on its display screen is presented in the type face you see to the
left.
Messages
Messages are used in this manual to bring important information to your attention.
Each type of message is identified as shown below.
CAUTION: Pay attention! A caution informs you that improper use of
equipment or failure to follow instructions may cause data loss or
damage your equipment.
NOTE: Please read. A note is a hint or advice that helps you make best
use of your equipment.
xxv
User's Manual
xxvi
General Precautions
TOSHIBA computers are designed to optimize safety, minimize strain and withstand
the rigors of portability. However, certain precautions should be observed to further
reduce the risk of personal injury or damage to the computer.
Be certain to read the general precautions below and to note the cautions included
in the text of the manual.
Stress injury
Carefully read the Instruction Manual for Safety & Comfort. It contains information
on prevention of stress injuries to your hands and wrists than can be caused by
extensive keyboard use. Chapter 3, Getting Started, also includes information on
work space design, posture and lighting that can help reduce physical stress.
Heat injury
❑
Avoid prolonged physical contact with the computer. If the computer is used
for long periods, its surface can become very warm. While the temperature will
not feel hot to the touch, if you maintain physical contact with the computer for
a long time (if you rest the computer on your lap, or if you keep your hands on
the palm rest, for example) your skin might suffer low-heat injury.
❑
If the computer has been used for a long time, avoid direct contact with the
metal plate supporting the I/O ports. It can become hot.
❑
The surface of the universal AC adaptor can become hot when in use. This
condition does not indicate a malfunction. If you need to transport the
universal AC adaptor, disconnect it and let it cool before moving it.
❑
Do not lay the universal AC adaptor on a material that is sensitive to heat. The
material could be damaged.
Pressure or impact damage
Do not apply heavy pressure to the computer or subject it to strong impact.
Excessive pressure or impact can cause damage to computer components or
otherwise cause malfunctions.
xxvii
User's Manual
Central Processing Unit ("CPU") Performance
Disclaimer
CPU Performance in your computer product may vary from specifications under the
following conditions:
use of certain peripheral products
use of battery power instead of AC power
use of certain multimedia games or videos with special effects
use of complex modeling software, such as high end computer aided design
application
use of computer in areas with low air puressure (high altitude >1,000 meters or
>3,280 feet above sea level)
use of computer at temperatures outside the range of 5°C to 35°C (41°F to 95°F)
or >25°C (77°F) at high altitude (all temperature reference are approximate).
Under some conditions, your computer product may automatically shut-down. This
is a normal protective feature designed to reduce the risk of lost data or damage to
the product when used outside recommended conditions. To avoid risk of lost data,
always make back-up copies of data by periodically storing it on an external strage
medium. For optimum performance, use your computer product only under
recommended conditions Read additional restrictions under “Environmental
Requirements” defined in the Appendix A. Contact TOSHIBA Service and Support
for more information.
PC card overheating
Some PC cards can become hot with prolonged use. Overheating of a PC card can
result in errors or instability in the PC card operation. Also be careful when you
remove a PC card that has been used for a long time.
xxviii
Introduction
This chapter provides an equipment checklist, and it identifies the computer’s
features, options and accessories.
CAUTION: Some of the features described in this manual may not
function properly if you use an operating system that was not preinstalled by TOSHIBA.
Equipment checklist
Carefully unpack your computer. Save the box and packing materials for future use.
Hardware
Check to make sure you have all the following items:
❑
❑
❑
❑
❑
Satellite 2450 Series Portable Personal Computer
Universal AC adaptor and power cord
USB diskette drive (Provided with some models)
Modular cable
Slim Select Bay weight saver module
Software
❑
The following software is preinstalled:
•
•
•
•
•
•
•
•
•
•
Microsoft® Windows XP Home Edition/Professional
Modem driver
Display Drivers for Windows
TOSHIBA Utilities
Wireless LAN driver (Can be used only for Wireless LAN models)
Bluetooth driver (Can be used only for Bluetooth models)
Sound Driver for Windows
DVD Video Player
LAN Drivers
Touch Pad Driver
1-1
INTRODUCTION
Chapter 1
INTRODUCTION
User's Manual
•
•
•
•
❑
TOSHIBA Power Saver
TOSHIBA Console
Infrared Device Driver
Online manual
Product Recovery CD-ROM
Documentation
•
•
•
•
Satellite 2450 Portable Personal Computer User's Manual
Microsoft Windows XP manual package
Instruction Manual for Safety & Comfort
End User License Agreement
Features
The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact
size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits:
Processor
Built-in
The computer is equipped with an Intel® Pentium®
processor, which incorporates a math co-processor, a 20 KB
level 1 cache memory and a 512 KB level 2 cache memory.
2.26 GHz
2.40 GHz
2.53 GHz
2.66 GHz
2.80 GHz
Intel® Pentium® 4 processor 2.26 GHz
Intel® Pentium® 4 processor 2.40 GHz
Intel® Pentium® 4 processor 2.53 GHz
Intel® Pentium® 4 processor 2.66 GHz
Intel® Pentium® 4 processor 2.80 GHz
Memory
Slots
128, 256 or 512 MB memory modules can be installed in the
two memory slots for a maximum of 1 GB system memory.
Video RAM
16 or 32 MB of RAM is provided for video display.
Battery pack
The computer is powered by one rechargeable lithium-ion
battery pack.
Power
1-2
Features
Universal AC adaptor
The computer has an internal battery to back up the
internal Real Time Clock (RTC) and calendar.
The universal AC adaptor provides power to the system
and recharges the batteries when they are low. It comes
with a detachable power cord.
Because it is universal, it can receive a range of AC
voltage from 100 to 240 volts; however, the output current
varies among different models. Using the wrong model can
damage your computer. See the universal AC adaptor
section in Chapter 2, The Grand Tour.
Disks
Hard disk drive
USB diskette drive
DVD-ROM drive
Available in three sizes.
• 27.94 GB (30.0 billion bytes)
• 37.26 GB (40.0 billion bytes)
• 55.88 GB (60.0 billion bytes)
Accommodates either 3 1/2" 1.44-megabyte or 720-kilobyte
diskettes. It connects to a USB port.
Some models are equipped with a full-size, DVD-ROM
drive module that lets you run either 12 cm (4.72") or 8 cm
(3.15") CD/DVDs without using an adaptor. It runs DVDROMs at maximum 8 speed and CD-ROMs at maximum 24
speed. A Mode Control button turns power to the fixed
DVD-ROM drive on and off so you can use the drive as a
stand-alone audio CD player. See Chapter 4, Operating
Basics, for details. The drive supports the following
formats:
•
•
•
•
•
•
•
•
DVD-ROM
• DVD-Video
CD-DA
• CD-Text
Photo CD™ (single/multi-session)
CD-ROM Mode 1, Mode 2
CD-ROM XA Mode 2 (Form1, Form2)
Enhanced CD (CD-EXTRA)
CD-G (Audio CD only)
Addressing Method 2
1-3
INTRODUCTION
RTC battery
INTRODUCTION
User's Manual
CD-RW/DVD-ROM
drive
Some models are equipped with a full-size, CD-RW/DVDROM drive module that lets you run CD/DVDs without
using an adaptor. It reads DVD-ROMs at maximum 8 speed
and CD-ROMs at maximum 24 speed. It writes CD-R at up
to 24 speed and CD-RW at up to 10 speed. A Mode
Control button turns power to the fixed CD-RW/DVDROM drive on and off so you can use the drive as a standalone audio CD player. See Chapter 4, Operating Basics,
for details. For reading, this drive supports the same
formats as the DVD-ROM drive.
DVD-R/-RW drive
Some models are equipped with a full- size DVD-R/RW
drive module that lets you record data to rewritable CD/
DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/
DVDs without using an adaptor. It reads DVD-ROMs at
maximum 8 speed and CD-ROMs at maximum 24 speed. It
writes CD-R at up to 16 speed, CD-RW at up to 10 speed,
DVD-R and DVD-RW at single speed. This drive supports
the same formats as the DVD-ROM drive.
•
•
•
•
•
•
•
•
DVD Multi drive
Some models are equipped with a full-size, DVD Multi
drive module that lets you run either 12 cm (4.72") or 8 cm
(3.15") CD/DVDs without using an adaptor. It reads DVDROMs at maximum 8 speed and CD-ROMs at maximum 24
speed. It writes CD-R at up to 16 speed, CD-RW at up to 8
speed, DVD-R and DVD-RW at single speed, and DVDRAM at 2 speed. The drive supports the following formats:
•
•
•
•
•
•
1-4
DVD-ROM
• DVD-Video
CD-DA
• CD-Text
Photo CD™ (single/multi-session)
CD-ROM Mode 1, Mode 2
CD-ROM XA Mode 2 (Form1, Form2)
Enhanced CD (CD-EXTRA)
CD-G (Audio CD only)
Addressing Method 2
DVD-ROM
CD-ROM
Audio CD
Photo CD
CD-ROMxA
CD-I
•
•
•
•
•
•
DVD-Video
CD-EXTRA
CD-R
CD-RW
CD-DA
DVD-RAM
Features
The computer’s LCD panel supports high-resolution video graphics. The screen
can be set at a wide range of viewing angles for maximum comfort and readability.
Built-in
Graphics controller
15.0" TFT screen, 16 M colors, with one of the following
resolutions:
• XGA, 1024 horizontal x 768 vertical pixels
• SXGA+, 1400 horizontal x 1050 vertical pixels
A 128-bit graphics controller maximizes display performance. Refer to Appendix B for more information.
Keyboard
Built-in
85 keys or 86 keys, compatible with IBM enhanced
keyboard, embedded numeric overlay, dedicated cursor
control,
and
keys. See Chapter 5, The Keyboard,
for details.
Pointing device
Built-in Touch Pad
A Touch Pad and control buttons in the palm rest enable
control of the on-screen pointer and scrolling of windows.
Ports
Parallel
Parallel printer or other parallel device (ECP compatible).
External monitor
15-pin, analog VGA port supports VESA DDC2B compatible functions.
Universal Serial Bus
(USB2.0)
The computer has three Universal Serial Bus ports that
comply with the USB 2.0 standard, which enables data
transfer speeds 40 times faster than the USB 1.1 standard.
(The ports also support USB 1.1.)
i.LINK™(IEEE1394)
This port enables high-speed data transfer directly from
external devices such as digital video cameras.
Infrared
The serial infrared port is compatible with Infrared Data
Association (IrDA 1.1) standards. It enables cableless 4
Mbps, 1.152 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2
kbps or 9.6 kbps data transfer with IrDA 1.1 compatible
external devices.
1-5
INTRODUCTION
Display
INTRODUCTION
User's Manual
Slots
PC card
The PC card slot accommodates two 5 mm Type II cards or
one Type III card.
SD card
This slot lets you easily transfer data from devices, such as
digital cameras and Personal Digital Assistants, that use
SD card flash-memory.
You can use memory module in this slot.
Multimedia
Sound system
Windows sound system compatible sound system
provides internal speakersas well as jacks for an external
microphone and headphone.
TV out
This jack lets you transfer video and sound data to
external devices. Use the TV adaptor cable for both videoout and line-out. Data output depends on the type of
device connected to the TV adaptor cable.
TV button
Press this button to set your display device to TV (Videoout). Press it again to return to the LCD.
Mode Control button
This button directly launches various CD, DVD and Digital
Audio functions. Refer to Chapter 4, Operating Basics, for
details.
Audio/Video
control buttons
Audio/Video control buttons let you use the computer’s
optical media drive as a stand-alone audio CD player. You
can also use the buttons to control the computer’s DVD
video player and TOSHIBA Media player when the system
is on.
1-6
Headphone jack
This jack outputs analog audio signals.
Microphone jack
A 3.5 mm mini microphone jack enables connection of a
three-conductor mini jack for monaural microphone input.
Features
Modem
LAN
Bluetooth
Wireless LAN
An internal modem provides capability for data and fax
communication. It supports V.90 (V.92). Refer to Appendix
E. The speed of data transfer and fax depends on analog
telephone line conditions. It has a modem jack for
connecting to a telephone line. It is preinstalled as a
standard device in some markets. Both of V.90 and V.92 are
supported only in USA and Canada. Only V.90 is available
in other regions.
The computer has built-in support for Ethernet LAN (10
megabits per second, 10BASE-T) and Fast Ethernet LAN
(100 megabits per second, 100BASE-Tx).
Some computers in this series are equipped with Bluetooth
functions. Bluetooth wireless technology eliminates the
need for cables between electronic devices such as
computers and printers. Bluetooth provides fast, reliable,
and secure wireless communication in a small space.
Some computers in this series are equipped with a wireless
LAN mini-PCI card that is compatible with other LAN
systems based on Direct Sequence Spread Spectrum radio
technology that complies with the IEEE802.11 Standard
(Revision A or B). Revision-A supports data transfer rate
up to 54Mbit/s. Revision-B supports data transfer rate up to
11Mbit/s.
Slim Select Bay
Modules
Slim Select Bay is a single-drive bay that accommodates a
DVD-ROM drive, CD-RW/DVD-ROM drive, DVD-R/-RW
drive, DVD Multi drive, Slim Select Bay HDD adaptor, or
Bridge media (for Memory Stick®/Smart Media/Compact
Flash™ memory) adaptor.
Security
Security lock slot
PC card lock
Connects an optional security lock to anchor the computer
to a desk or other large object
A PC card can be secured by an optional security lock to
prevent access to the PC card slot.
1-7
INTRODUCTION
Communications
INTRODUCTION
User's Manual
Software
Standard
Plug and Play
Windows XP operating system and TOSHIBA Utilities and
drivers preinstalled on the hard disk.
When you connect an external device to the computer,
Plug and Play capability enables the system to recognize
the connection and make the necessary configurations
automatically.
Special features
The following features are either unique to TOSHIBA computers or are advanced
features, which make the computer more convenient to use.
Internet button
TOSHIBA Console
button
Press this button to launch an Internet browser. See
Chapter 2, Grand Tour, for details.
Press this button to launch an application automatically.
The default is TOSHIBA Console.
Hot keys
Key combinations let you quickly modify the system
configuration directly from the keyboard without running a
system configuration program.
Display automatic
power off
This feature automatically cuts off power to the internal
display when there is no input from the keyboard or
pointing device for a time specified. Power is restored when
any key is pressed or when there is input from a pointing
device. You can specify the time in the Turn off monitor
item of the Power Save Mode window in TOSHIBA Power
Saver.
HDD automatic
power off
This feature automatically cuts off power to the hard disk
drive when it is not accessed for a time specified. Power is
restored when the hard disk is accessed. You can specify
the time in the Turn off hard disks item of the Power Save
Mode window in TOSHIBA Power Saver.
System automatic
Standby/Hibernation
This feature automatically shuts down the system in
standby mode or Hibernation mode when there is no input
or hardware access for a time specified. You can specify
the time and select either System Standby or System
Hibernate in the System standby and System hibernate
item of the Power Save Mode window in TOSHIBA Power
Saver.
1-8
Special features
A ten-key pad is integrated into the keyboard. Refer to the
Keypad overlay section in Chapter 5, Keyboard, for
instructions on using the keypad overlay.
Power on password
Two levels of password security, supervisor and user, are
available to prevent unauthorized access to your computer.
Instant security
A hot key function blanks the screen and disables the
computer providing data security.
Intelligent
power supply
A microprocessor in the computer’s intelligent power
supply detects the battery’s charge and calculates the
remaining battery capacity. It also protects electronic
components from abnormal conditions, such as voltage
overload from a universal AC adaptor. You can monitor
remaining battery capacity. Use the Battery remaining item
of the Power Save Modes window in TOSHIBA Power
Saver.
Battery save mode
This feature lets you save battery power. You can specify
the Power Save Mode in the Running on batteries item of
the Power Save Modes window in TOSHIBA Power Saver.
Panel power off/on
This feature turns power to the computer off when the
display panel is closed and turns it back on when the panel
is opened. You can specify the setting in the When I close
the lid item of the System Power Mode window in
TOSHIBA Power Saver.
Low battery
automatic hibernation
When battery power is exhausted to the point that
computer operation cannot be continued, the system
automatically enters Hibernation and shuts down. You can
specify the setting in the Battery Alarm item of the Alarm
window in TOSHIBA Power Saver.
Heat dispersal
The CPU has an internal temperature sensor that automatically activates cooling procedures. Refer to the Heat
dispersal section in Chapter 4, Operating Basics, for
details on setting the options for cooling methods.
Hibernation
This feature lets you turn off the power without exiting
from your software. The contents of main memory is saved
to the hard disk, when you turn on the power again, you
can continue working right where you left off. Refer to the
Turning off the power section in Chapter 3, Getting
Started, for details.
1-9
INTRODUCTION
Keypad overlay
INTRODUCTION
User's Manual
Standby
If you have to interrupt your work, you can turn off the
power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on
the power again, you can continue working right where
you left off.
Utilities
This section describes preinstalled utilities and tells how to start them. For details
on operations, refer to each utility’s online manual, help files or read.me files.
TOSHIBA Power Saver To access this power savings management program, open
the Control Panel and select the TOSHIBA Power Saver
icon.
HW Setup
This program lets you customize your hardware settings
according to the way you work with your computer and
the peripherals you use. To start the utility, click the
Windows Start button and click Control Panel. In the
Control Panel, select the TOSHIBA HW Setup icon.
TOSHIBA Controls
This utility has four sections to let you do the following:
• Buttons: Assign applications to the Internet button
(default setting is the browser) and to the TOSHIBA
Console button (default setting is the TOSHIBA
Console).
• Media Apps: Set the mode for the Audio/Video control
buttons. Select the application for audio and video
playback.
TOSHIBA Console
TOSHIBA Console is a graphical user interface that
provides access to help and services. It is the default
function launched by the TOSHIBA Console button.
Fn-esse
This Windows program lets you define your own “shortcut” keys to quickly launch applications and speed your
work in Windows. To start the utility, click the Windows
Start button, point to All Programs, point to TOSHIBA
Utilities and click Fn-esse.
DVD Video Player
The DVD Video Player is used to play DVD-Video. It has
an on-screen interface and functions. Click Start, point to
All Programs, point to InterVideo WinDVD 4, then click
InterVideo WinDVD 4.
1-10
Options
ConfigFree is a suite of utilities to allow easy control of
communication device and network connections.
ConfigFree also allows you to find communication
probrems and create profiles for easy switching between
location and communication networks.
You can boot ConfigFree from the menu bar as follows.
[Start] - [All Programs] - [TOSHIBA ConfigFree] - [ConfigFree]
Bluetooth TOSHIBA
Stack
This software enables communication between remote
Bluetooth devices. Refer to the Quick Start Guide.
Drag’n Drop CD
This easy-to-use software lets you record CDs with just a
few mouse clicks. You can create CDs in several formats
including audio CDs that can be played on a standard
stereo CD player and data CDs to store the files and
folders on your hard drive. This software can be used on
the model with CD-RW/DVD-ROM drive, DVD-R/-RW
drive or DVD Multi drive.
TOSHIBA Mobile
Extension
This utility enables hot insertion of Slim Select Bay
modules, that is, you can remove/insert Slim Select Bay
modules while the computer is on. To activate this utility,
select TOSHIBA Mobile Extension from TOSHIBA
Console.
Options
You can add a number of options to make your computer even more powerful
and convenient to use. The following options are available:
Memory expansion
Battery pack (Black)
A 128, 256 or 512 MB memory module (PC2100, DDR) can
easily be installed in the computer.
An additional battery pack can be purchased from your
TOSHIBA dealer. Use it as a spare or replacement.
Universal AC adaptor
If you use your computer at more than one site frequently,
it may be convenient to purchase an additional universal
AC adaptor for each site so you will not have to carry the
adaptor with you.
Battery charger
The battery charger lets you charge extra batteries outside
the computer.
1-11
INTRODUCTION
ConfigFree
INTRODUCTION
User's Manual
Security lock
A slot is available to attach a security cable to the computer to deter theft.
USB FDD Kit
A 3 1/2" diskette drive accommodates 1.44-megabyte or
720-kilobyte diskette. It connects to a USB port. (You
cannot format 720-kilobyte diskettes on Windows XP, but
you can use previously formatted disks.)
Wireless LAN Kit
This option enbles wireless LAN functions in computers
that do not have wireless preinstalled. It is installed by
dealers only. Two types of Wireless LAN kit are prepared:
Wireless LAN Kit for IEEE 802.11 Standard (Revision B)
and Wireless LAN Kit for IEEE 802.11 Standard (Revision
A and B)
Slim Select Bay options
The following modules can be installed in the Slim Select Bay. The user can select
either a DVD-ROM drive, a CD-RW/DVD-ROM drive, a DVD-R/-RW drive, a DVD
Multi drive, a Slim Select Bay HDD adaptor or a TOSHIBA Style Bay Bridge media
adaptor, to be preinstalled as a standard device. All other modules are options.
DVD-ROM(Black)
Refer to the Features section for details.
CD-RW/DVD-ROM
(Black)
Refer to the Features section for details.
DVD-R/-RW drive
(Black)
Refer to the Features section for details.
DVD Multi (Black)
Refer to the Features section for details.
Slim Select Bay
HDD adaptor
An adaptor lets you install an optional HDD described
in Chapter 8, Optional Devices.
Hard disk drive
You can increase your computer’s data storage capacity
with an additional 30 GB (27.94 billion bytes), 40 GB (37.26
billion bytes) and 60 GB (55.89 billion bytes) hard disk
drive in the Slim Select Bay HDD adaptor.
TOSHIBA Style Bay
Bridge media adaptor
1-12
This adaptor lets you install an optional Bridge media
(Memory Stick/Smart Media/Compact Flash memory)
adaptor described in Chapter 8, Optional Devices.
Chapter 2
The Grand Tour
Front with the display closed
Figure 2-1 shows the computer’s front with its display panel in the closed position.
MODE
AUDIO/VIDEO
AUDIO/VIDEO
VOLUME
CONTROL
CONTROL
DISPLAY LATCH
CONTROL
CONTROL
BUTTON
BUTTONS
BUTTONS
SYSTEM INDICATORS
Figure 2-1 Front of the computer with display closed
Audio/Video
control buttons
Previous
button: Plays the previous track/chapter/
data. Play/pause
button: Begins or pauses play. Stop
button: Halts play. Next
button: Plays the next
track/chapter/data. Refer to Chapter 4, Operating Basics.
NOTE: If Random is selected in TOSHIBA Media Player, selecting Next
or Previous advances to a random selection.
Mode Control
button
Press this button to switch the mode between CD/DVD
and Digital Audio.
2-1
THE GRAND TOUR
This chapter identifies the various components of your computer. Become familiar
with each component before you operate the computer.
User's Manual
Display latch
Volume control
THE GRAND TOUR
System
indicators
This latch secures the LCD panel in its closed position.
Slide the latch to open the display.
Use this dial to adjust the volume of the stereo speakers
and subwoofer or the stereo headphones.
LEDs let you monitor the status of various computer
functions. Details are given in the Indicators section.
Left side
Figure 2-2 shows the computer’s left side.
SECURITY LOCK
COOLING
WIRELESS COMMUNICATION
WIRELESS COMMUNICATION
SWITCH
INDICATOR
PC CARD SLOTS
USB PORT
INFRARED PORT
VENTS
Figure 2-2 The left side of the computer
Security lock
Wireless
communication
switch
On
Off
A security cable attaches to this slot. The optional security
cable anchors your computer to a desk or other large
object to deter theft.
Slide this switch toward the front of the computer to turn
off Wireless LAN and Bluetooth functions. Slide it toward
the back of the computer to turn on the functions (Wireless model or Wireless LAN ready model only).
CAUTION: Set the switch to off in airplanes and hospitals. Check the
wireless communication indicator. It will stop glowing when the wireless
communication function is off.
Wireless
communication
Indicator
2-2
This indicator glows orange when the Bluetooth and
Wireless LAN functions are on (Wireless model or
Wireless LAN ready model only).
Left side
Cooling vents
These vents provide an outlet for air pulled through the
computer by the fan.
CAUTION: Be careful not to block the cooling vents. Also be careful to
keep foreign objects out of them. A pin or similar object can damage the
computer’s circuitry.
CB
A PC card slot can accommodate two 5 mm Type IIcards or
one Type III card. You can install any industry standard
PC card such as a SCSI adaptor, Ethernet adaptor or flash
memory card.
CAUTION: Keep foreign objects out of the PC card slot. A pin or similar
object can damage the computer’s circuitry.
Universal
Serial Bus
(USB 2.0) port
A Universal Serial Bus port is on the left side. The
port comply with the USB 2.0 standard, which enables
data transfer speeds 40 times faster than the USB 1.1
standard. (The ports also support USB 1.1.)
CAUTION: Keep foreign objects out of the USB connectors. A pin or
similar object can damage the computer’s circuitry.
NOTE: Operation of all functions of all USB devices has not been
confirmed. Some functions might not execute properly.
Infrared port
This infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps,
1.15 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or
9.6 kbps data transfer with IrDA 1.1 compatible external
devices.
2-3
THE GRAND TOUR
PC card slot
User's Manual
Right side
THE GRAND TOUR
Figure 2-3 shows the computer’s right side.
SD CARD SLOT
SD CARD INDICATOR
HEADPHONE JACK
MICROPHONE JACK
MODEM JACK
SLIM SELECT BAY
LINE-IN JACK
Figure 2-3 The right side of the computer
SD card slot
SD cards are used in a wide variety of external devices.
This slot lets you transfer data from the device to your
computer. An indicator on the right side of the slot glows
when a card is being accessed.
CAUTION: Keep foreign objects out of the SD card slot. A pin or similar
object can damage the computer’s circuitry.
SD card indicator
This indicator glows green when the computer is accessing the SD card slot.
Modem jack
In areas where an internal modem is installed as standard
equipment, there is a modem jack that lets you use a
modular cable to connect the modem directly to a telephone line.
CAUTIONS: 1. In case of a lightning storm, unplug the modem cable
from the telephone jack.
2. Do not connect the modem to a digital telephone line.
A digital line will damage the modem.
Slim Select Bay
2-4
A DVD-ROM drive, CD-RW/DVD-ROM drive, DVD-R/RW drive, DVD Multi drive, optical Slim Select Bay HDD
adaptor, optional Bridge media adaptor can be installed in
the Slim Select Bay.
Back side
This jack lets you connect digital speakers or a stereo
headphone (16 ohm minimum). When you connect a
digital speaker or headphones, the internal speaker is
automatically disabled.
Microphone jack
A 3.5 mm mini microphone jack enables connection of a
three-conductor mini jack for monaural microphone input.
Line-in jack
A standard 3.5 mm mini line-in jack enables connection of
a stereo device for audio input.
Back side
Figure 2-4 shows the computer’s back panel.
LAN ACTIVE
INDICATOR (ORANGE)
LINK INDICATOR
(GREEN)
EXTERNAL MONITOR
PARALLEL
PORT
PORT
DC IN 15V LAN
USB
TV OUT
COOLING
I.LINK (IEEE 1394)
JACK
PORTS
PORT
VENTS
PORT
Figure 2-4 The back side of the computer
LAN active
indicator (orange)
This indicator glows orange when data is being exchanged
between the computer and the LAN.
Link indicator
(green)
This indicator glows green when the computer is connected to a LAN and the LAN is functioning properly.
External monitor
port
This 15-pin port lets you connect an external video
display.
2-5
THE GRAND TOUR
Headphone jack
User's Manual
Parallel port
DC IN 15V
THE GRAND TOUR
DC IN 15V
LAN jack
Ether
This Centronics-compatible, 25-pin parallel port is used to
connect a parallel printer or other parallel device. This port
supports Extended Capabilities Port (ECP) standard.
The universal AC adaptor connects to this socket. Use
only the model of universal AC adaptor that comes with
the computer. Using the wrong adaptor can damage your
computer.
This jack lets you connect to a LAN. The adaptor has
built-in support for Ethernet LAN (10 megabits per second,
10BASE-T) and Fast Ethernet LAN (100 megabits per
second, 100BASE-Tx). The LAN has two indicators. See
Chapter 4, Operating Basics, for details.
Universal
Serial Bus
(USB 2.0) ports
Two Universal Serial Bus (USB 2.0 compliant) ports are on
the back side. See Universal Serial Port in the Left side
section for details.
TV out port
Plug an S-Video cable into this jack for both
line-out and video-out. The S-Video cable carries video as
well as audio data for left and right speakers. Use the TV
button to turn on and off the TV display.
Cooling vents
These vents provide an outlet for air pulled through the
computer by the fan.
CAUTION: Be careful not to block the cooling vents. Also be careful to
keep foreign objects out of them. A pin or similar object can damage the
computer’s circuitry.
i.LINK (IEEE1394)
port
2-6
Connect an external device, such as a digital video camera
to this port for high-speed data transfer.
Under side
Underside
Figure 2-5 shows the underside of the computer. Make sure the display is closed
before turning over your computer.
SLIM SELECT BAY LATCH
CPU COOLING FAN WITH AIR FILTER
BATTERY RELEASE LATCH
Figure 2-5 The underside of the computer
Slim Select Bay
latch
Slide this latch to free the Slim Select Bay for removal.
CPU cooling fan
with air filter
This cooling fan intakes air to cool cpu and air filter
prevents dusts from entering into the computer.
CAUTION: Remove the dust from the filter regularly with vacuum
cleaner.
Battery pack
The battery pack powers the computer when the universal
AC adaptor is not connected. For detailed information on
the battery pack, refer to Chapter 6, Power and Power-Up
Modes.
2-7
THE GRAND TOUR
BATTERY
PACK
User's Manual
Battery release
latch
Slide this latch to release the battery pack for removal.
THE GRAND TOUR
Front with the display open
Figure 2-6 shows the front of the computer with the display open. To open the
display, push the display latch on the front of the display and lift up. Position the
display at a comfortable viewing angle.
DISPLAY HINGE
DISPLAY SCREEN
STEREO SPEAKER
(RIGHT)
TV BUTTON
TOSHIBA
CONSOLE BUTTON
INTERNET BUTTON
STEREO SPEAKER
(LEFT)
POWER BUTTON
TOUCH PAD
TOUCH PAD CONTROL BUTTONS
Figure 2-6 The front with the display open
Display hinge
2-8
The display hinge holds the display screen at easy-toview angles.
Front with the display open
Display screen
The LCD displays high-contrast text and graphics. The
computer’s LCD consists of up to 1024 x 768 pixels or 1400
x 1050 pixels. Refer to Appendix B.
Internet button
TOSHIBA Console
button
TV button
Press this button to launch an Internet browser. If the
computer’s power is off, you can press this button to turn
on the computer’s power and launch the browser automatically in one step.
Press this button to launch an application automatically.
The default is TOSHIBA Console.
Press this button to set your display device to TV (Videoout). Press it again to return to LCD.
Stereo speakers
The speakers emit sound generated by your software as
well as audio alarms, such as low battery condition,
generated by the system.
Power button
Press the power button to turn the computer’s power on
and off.
Touch Pad
A Touch Pad located in the center of the palm rest is used
to control the on-screen pointer. Refer to the Using the
Touch Pad section in Chapter 4, Operating Basics.
Touch Pad
control buttons
Control buttons below the DVD Multi let you select menu
items or manipulate text and graphics designated by the
on-screen pointer.
2-9
THE GRAND TOUR
When the computer operates on the universal AC adaptor
the display screen’s image will be somewhat brighter than
when it operates on battery power. The lower brightness
level is intended to save battery power.
User's Manual
System indicators
THE GRAND TOUR
CD/DVD
DIGITAL
AUDIO
DC IN 15V
POWER
BATTERY
DISK
SLIM SELECT
BAY
Figure 2-7 System indicators
2-10
CD/DVD
The CD/DVD indicator glows in green when reproducing
CD/DVD. This LED does not light usually and is locked
not to light. Press the Mode control button for four
seconds to unlock. Then CD/DVD indicator is set to light
as default. Every time you press the Mode control button,
lighting indicator changes between CD/DVD indicator and
Digital Audio indicator in turn.
Digital Audio
The Digital Audio indicator in green when reproducing
when reproducing music files (WAVE file, MIDI file, or
MP3 files, etc). This LED does not light usually and is
locked not to light. Press the Mode control button for four
seconds to unlock. Then CD/DVD indicator is set to light
as default. Every time you press the Mode control button,
lighting indicator changes between CD/DVD indicator and
Digital Audio indicator in turn.
DC IN 15V
The DC IN indicator glows green when DC power is
supplied from the AC power adaptor. If the adaptor’s
output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange.
Power
The Power indicator glows green when the computer is
on. If you select Standby from Shut Down Windows,
this indicator flashes orange (one second on, two seconds
off) while the computer shuts down.
Battery
The Battery indicator shows the condition of the
battery’s charge: Green indicates full charge, orange
indicates battery charging and flashing orange indicates a
low battery charge. Refer to Chapter 6, Power and PowerUp Modes.
Keyboard indicators
Disk
Slim Select Bay
The Disk indicator glows green when the computer is
accessing the built-in hard disk or fixed optical media drive.
Keyboard indicators
The figures below show the positions of the keypad overlay indicators and the
CapsLock indicator.
When the F10 key indicator glows the keypad overlay lets you control the cursor.
When the F11 key indicator glows the keypad overlay lets you enter numbers.
NUMERIC MODE
INDICATOR
ARROW MODE
INDICATOR
Figure 2-8 Keypad overlay indicators
2-11
THE GRAND TOUR
The Slim Select Bay indicator glows green when the
computer is accessing a DVD-ROM drive, CD-RW/DVDROM drive, DVD-R/-RW drive, DVD Multi drive or Slim
Select Bay HDD adaptor in the Slim Select Bay.
User's Manual
When the CapsLock indicator glows the keyboard is in all-caps mode.
CAPSLOCK
THE GRAND TOUR
INDICATOR
Figure 2-9 CapsLock indicator
Caps Lock
Arrow mode
Numeric mode
This indicator glows green when the alphabet keys are
locked in uppercase.
When the Arrow mode indicator lights green, you can
use the keypad overlay (gray labeled keys) as cursor keys.
Refer to the Keypad overlay section in Chapter 5, The
Keyboard.
You can use the keypad overlay (gray labeled keys) for
numeric input when the Numeric mode indicator lights
green. Refer to the Keypad overlay section in Chapter 5,
The Keyboard.
USB diskette drive
A 3 1/2" diskette drive accommodates 1.44-megabyte or 720-kilobyte diskettes. It
connects to the USB port.
DISK-IN-USE
INDICATOR
DISKETTE SLOT
EJECT BUTTON
2-12
Figure 2-10 USB diskette drive
Slim Select Bay modules
Disk-In-Use
Indicator
This indicator lights when the diskette is being accessed.
Diskette slot
Insert diskettes in this slot.
Eject button
When a diskette is fully seated in the drive, the eject
button pops out. To remove a diskette, push in the eject
button and the diskette pops out partially for removal.
NOTES: 1. The external diskette drive should be placed on a flat,
horizontal surface when in use. Do not set the drive on an
incline greater than 20o while it is operating.
2. Do not set anything on top of the diskette drive.
Slim Select Bay modules
The Slim Select Bay can accommodate the following modules: DVD-ROM drive, CDRW/DVD-ROM drive, DVD-R/-RW drive, DVD Multi drive, optional Slim Select
Bay HDD adaptor or TOSHIBA Style Bay Bridge media adaptor.
DVD-ROM drive
Refer to the DVD-ROM drive item in the Fixed optical media drive section for
details.
CD/DVD-IN-USE
INDICATOR
EJECT HOLE
EJECT BUTTON
Figure 2-11 The DVD-ROM drive
2-13
THE GRAND TOUR
CAUTION: Check the Disk-In-Use indicator when you use the diskette
drive. Do not press the eject button or turn off the computer while the light is
glowing. Doing so could destroy data and damage the diskette or the drive.
User's Manual
CD-RW/DVD-ROM drive
Refer to the CD-RW/DVD-ROM drive item in the Fixed optical media drive section
for details.
THE GRAND TOUR
NOTE: The physical features of this drive are similar to those of the
DVD-ROM drive. Refer to the illustration in the DVD-ROM drive section.
CAUTION: Check the Slim Select Bay indicator when you use the
DVD-ROM drive or CD-RW/DVD-ROM drive in the Slim Select Bay. Do
not press the eject button, disconnect a drive or turn off the computer
while the light is glowing. Doing so could damage the CD/DVD or the
drive.
DVD-R/-RW drive
The full- size DVD-R/RW drive module lets you record data to rewritable CD/DVDs
as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an
adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24
speed. It writes CD-R at up to 16 speed, CD-RW at up to 10 speed, DVD-R and
DVD-RW at single speed. This drive supports the same formats as the DVD-ROM
drive.
•
•
•
•
•
•
DVD-ROM
CD-DA
Audio CD
Photo CD (single/multi-session)
CD-ROM XA Mode 2 (Form 1, Form 2)
CD-G (Audio CD only)
2-14
•
•
•
•
•
•
DVD-Video
CD-Text
CD-R
CD-ROM Mode 1, Mode 2
Enhanced CD (CD EXTRA)
Addressing Method 2
Slim Select Bay modules
DVD Multi drive
The full-size DVD Multi drive module lets you run either 12 cm (4.72") or 8 cm (3.15")
CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and
CD-ROMs at maximum 24 speed. It writes CD-R at up to 16 speed, CD-RW at up to 8
speed, DVD-R and DVD-RW at single speed, and DVD-RAM at 2 speed. The drive
supports the following formats:
DVD-ROM
CD-ROM
Audio CD
Photo CD
CD-ROMxA
CD-I
•
•
•
•
•
•
THE GRAND TOUR
•
•
•
•
•
•
DVD-Video
CD-EXTRA
CD-R
CD-RW
CD-DA
DVD-RAM
DVD Multi drives and disc are manufactured according to the specifications of six
marketing regions. When you purchase DVD-Video media, make sure it matches
your drive, otherwise it will not play properly.
Code
1
2
3
4
5
6
Region
Canada, United States
Japan, Europe, South Africa, Middle East
Southeast Asia, East Asia
Australia, New Zealand, Pacific Islands, Central America, South
America, Caribbean
Russia, Indian Subcontinent, Africa, North Korea, Mongolia
China
NOTE: Use the WinDVD 4 application to view DVD-Video discs.
CD-R and DVD-R discs can be written only once. The recorded data cannot be
erased or changed.
CD-RW discs that can be recorded more than once. Use either 1, 2, or 4 multi speed
CD-RW discs or high-speed 4- to 10-speed discs. The write speed of the high-speed
CD-RW discs is maximum 10-speed.
DVD-RW/-RAM discs can be recorded more than once.
For information on loading and unloading discs and on the Mode Control buttons
refer to the Using optical media drives and Audio/Video controls section in the
computer’s user’s manual.
2-15
User's Manual
Slim Select Bay HDD adaptor (Black)
You can increase your computer’s data storage capacity by installing an optional,
integrated, 2 1/2" HDD in the Slim Select Bay.
THE GRAND TOUR
RELEASE LATCH
Figure 2-12 The Slim Select Bay HDD adaptor (Black)
TOSHIBA Style Bay Bridge Media Adaptor
Three types of memory, a Smart Media, a Memory Stick and a Compact Flash
memory can be installed and used in the Bridge media adaptor.
Figure 2-13 TOSHIBA Style Bay Bridge media adaptor
2-16
Universal AC adaptor
Universal AC adaptor
The universal AC adaptor converts AC power to DC power and reduces the voltage
supplied to the computer. It can automatically adjust to any voltage from 100 to 240
volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in
almost any country/region.
Figure 2-14 The universal AC adaptor
CAUTION: Use only the universal AC adaptor that came with the
computer or an equivalent optional adaptor. Use of the wrong adaptor
could damage your computer. TOSHIBA assumes no liability for any
damage in such case.
2-17
THE GRAND TOUR
To recharge the battery, simply connect the universal AC adaptor to a power source
and the computer. See Chapter 6 Power and Power-Up Modes for details.
THE GRAND TOUR
User's Manual
2-18
Chapter 3
Getting Started
This chapter provides basic information to get you started using your computer. It
covers the following topics:
❑
Setting up your work space — for your health and safety
NOTE: Be sure also to read Instruction Manual for Safety & Comfort.
This guide, which is included with the computer, explains product
liability.
Connecting the universal AC adaptor
❑
Opening the display
❑
Turning on the power
❑
Starting up for the first time
❑
Turning off the power
❑
Restarting the computer
❑
Restoring the preinstalled software from the Product Recovery CD-ROM
GETTING STARTED
❑
NOTE: All users should be sure to read the section Starting up for the
first time.
Setting up your work space
Establishing a comfortable work site is important for you and your computer. A
poor work environment or stressful work habits can result in discomfort or serious
injury from repetitive strain to your hands, wrists or other joints. Proper ambient
conditions should also be maintained for the computer’s operation. This section
discusses the following topics:
❑
General conditions
❑
Placement of the computer
❑
Seating and posture
❑
Lighting
❑
Work habits
3-1
User's Manual
General conditions
GETTING STARTED
In general, if you are comfortable, so is your computer, but read the following to
make sure your work site provides a proper environment.
❑
Make sure there is adequate space around the computer for proper ventilation.
❑
Make sure the AC power cord connects to an outlet that is close to the
computer and easily accessible.
❑
The temperature should be 5 to 35 degrees Centigrade (41 to 95 degrees
Fahrenheit) and the relative humidity should be 20 to 80 percent.
❑
Avoid areas where rapid or extreme changes in temperature or humidity may
occur.
❑
Keep the computer free of dust, moisture, and exposure to direct sunlight.
❑
Keep the computer away from heat sources, such as electric heaters.
❑
Do not use the computer near liquids or corrosive chemicals.
❑
Do not place the computer near objects that create strong magnetic fields (e.g.,
stereo speakers).
❑
Some computers in the computer, including data storage media, can be
damaged by magnets. Do not place the computer near magnetic objects or
bring magnetic objects close to the computer. Be careful of objects, such as
stereo speakers, that produce strong magnetic fields during operation. Also, be
careful with metal objects, such as bracelets, which can be inadvertently
magnetized.
❑
Do not operate the computer in close proximity to a mobile phone.
❑
Leave ample ventilation room for the fan. Do not block the vents.
Placement of the computer
Position the computer and peripheral devices to provide comfort and safety.
❑
Set the computer on a flat surface at a comfortable height and distance. The
display should be no higher than eye level to avoid eye strain.
❑
Place the computer so that it is directly in front of you when you work and
make sure you have adequate space to easily operate other devices.
❑
Allow adequate space behind the computer to let you freely adjust the display.
The display should be angled to reduce glare and maximize visibility.
❑
If you use a paper holder, set it at about the same height and distance as the
computer.
3-2
Setting up your work space
Seating and posture
The height of your chair in relation to the computer and keyboard as well as the
support it gives your body are primary factors in reducing work strain. Refer to the
following tips and to figure 3-1.
BELOW EYE LEVEL
GETTING STARTED
FOOT REST
90O ANGLES
Figure 3-1 Posture and positioning of the computer
❑
Place your chair so that the keyboard is at or slightly below the level of your
elbow. You should be able to type comfortably with your shoulders relaxed.
❑
Your knees should be slightly higher than your hips. If necessary, use a foot
rest to raise the level of your knees to ease pressure on the back of your thighs.
❑
Adjust the back of your chair so it supports the lower curve of your spine.
❑
Sit straight so that your knees, hips and elbows form approximately 90 degree
angles when you work. Do not slump forward or lean back too far.
3-3
User's Manual
Lighting
Proper lighting can improve legibility of the display and reduce eye strain.
❑
Position the computer so that sunlight or bright indoor lighting does not reflect
off the screen. Use tinted windows, shades or other screen to eliminate sun
glare.
❑
Avoid placing the computer in front of bright light that could shine directly in
your eyes.
❑
If possible, use soft, indirect lighting in your computer work area. Use a lamp to
illuminate your documents or desk, but be sure to position the lamp so that it
does not reflect off the display or shine in your eyes.
GETTING STARTED
Work habits
A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your work day. If you must spend
long periods at the computer, finding ways to break up the routine can reduce
stress and improve your efficiency.
❑
Sit in a relaxed posture. Good positioning of your chair and equipment as
described earlier can reduce tension in your shoulders or neck and ease back
strain.
❑
Vary your posture frequently.
❑
Occasionally stand up and stretch or exercise briefly.
❑
Exercise and stretch your wrists and hands a number of times during the day.
❑
Frequently, look away from the computer and focus your eyes on a distant
object for several seconds, for example 30 seconds every 15 minutes.
❑
Take frequent short breaks instead of one or two long breaks, for example, two
or three minutes every half hour.
❑
Have your eyes examined regularly and visit a doctor promptly, if you suspect
you might be suffering from a repetitive strain injury.
A number of books are available on ergonomics and repetitive strain injury or
repetitive stress syndrome. For more information on these topics or for pointers on
exercises for such stress points as hands and wrists, please check with your library
or book vendor. Also refer to the computer’s Instruction Manual for Safety &
Comfort.
3-4
Connecting the AC adaptor
Connecting the universal AC adaptor
Attach the universal AC adaptor when you need to charge the battery or you want
to operate from AC power. It is also the fastest way to get started, because the
battery pack will need to be charged before you can operate from battery power.
The universal AC adaptor can be connected to any power source supplying from
100 to 240 volts and 50 or 60 hertz. For details on using the universal AC adaptor to
charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
CAUTION: Use of the wrong adaptor could damage your computer.
TOSHIBA assumes no liability for any damage in such case. The current
rating for the computer is 6.0 amperes.
1. Connect the power cord to the universal AC adaptor.
GETTING STARTED
Figure 3-2 Connecting the power cord to the universal AC adaptor
2. Connect the universal AC adaptor’s DC output plug to the DC IN input port
on the back of the computer.
Figure 3-3 Connecting the adaptor to the computer
3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators
on the front of the computer should glow.
3-5
User's Manual
Opening the display
The display panel can be rotated in a wide range of angles for optimal viewing.
1. Slide the display latch on the front of the computer to the right.
2. Lift the panel up and adjust it to the best viewing angle for you.
CAUTION: Use reasonable care when opening and closing the display
panel. Opening it vigorously or slamming it shut could damage the
computer.
GETTING STARTED
DISPLAY LATCH
Figure 3-4 Opening the display
Turning on the power
This section describes how to turn on the power.
NOTE: After you turn on the power for the first time, do not turn it off
until you have set up the operating system. Refer to the section Starting
up for the first time in this chapter.
1. Open the display.
3-6
Starting up for the first time
2. Press and hold the computer’s power button for two or three seconds.
Figure 3-5 Turning on the power
When you first turn on the power, the computer’s initial screen is the Microsoft
Windows XP Startup Screen Logo. Follow the on-screen directions for each screen.
During setup, you can click the Back button to return to the previous screen.
Be sure to read the Windows End User License Agreement display
carefully.
NOTE: Be sure to read the License Agreement carefully.
Turning off the power
The power can be turned off in one of the following modes: Shut down (Boot),
Hibernation or Standby mode.
Shut Down mode (Boot mode)
When you turn off the power in Shut Down mode no data is saved and the
computer will boot to the operating system’s main screen.
1. If you have entered data, save it to the hard disk or to a diskette.
2. Make sure all disk activity has stopped, then remove the CD/DVD-ROM or
diskette.
CAUTION: Make sure the Disk, Slim Select Bay and Slim Select Bay’s
module indicators are off. If you turn off the power while a disk is being
accessed, you can lose data or damage the disk.
3-7
GETTING STARTED
Starting up for the first time
User's Manual
3. Click start then click Turn Off Computer. From the Turn Off Computer menu
select Turn Off.
4. Turn off the power to any peripheral devices.
CAUTION: Do not turn the computer or devices back on immediately. Wait
a moment to let all capacitors fully discharge.
Hibernation mode
The hibernation feature saves the contents of memory to the hard disk when the
computer is turned off. The next time the computer is turned on, the previous state
is restored. The hibernation feature does not save the status of peripheral devices.
GETTING STARTED
CAUTIONS: 1. Save your data. While entering hibernation mode, the
computer saves the contents of memory to the HDD.
However, for safety sake, it is best to save your data
manually.
2. Data will be lost if you remove the battery or disconnect the universal AC adaptor before the save is
completed. Wait for the Disk indicator to go out.
3. Do not install or remove a memory module while the
computer is in hibernation mode. Data will be lost.
Benefits of hibernation
The hibernation feature provides the following benefits:
❑
Saves data to the hard disk when the computer automatically shuts down
because of a low battery.
NOTE: For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the
Hibernate window and the Battery Alarm item of the Alarm window.
Otherwise, the computer will shut down in Standby mode. If battery power
becomes depleted, data saved in Standby will be lost.
❑
You can return to your previous working environment immediately when you
turn on the computer.
❑
Saves power by shutting down the system when the computer receives no
input or hardware access for the duration set by the System hibernate feature.
❑
You can use the panel power off feature.
3-8
Turning off the power
Starting Hibernation
NOTE: You can also enable Hibernation by pressing Fn + F4. See
Chapter 5, Keyboard, for details.
To enter Hibernation mode, follow the steps below.
1. Click start .
2. Select Turn Off Computer.
3. Open the Turn Off Computer dialog box. Hibernate is not displayed.
4. Press the Shift key. The Standby item will change to Hibernate.
5. Select the Hibernate.
Automatic Hibernation
1. Open the Control Panel.
2. In Windows XP, open Performance and Maintenance and open
TOSHIBA Power Saver.
3. Select the Hibernate window, select the Enable Hibernate support check
box and click the Apply button.
4. Select the Power Save Modes window.
5. Double-click Power Mode (Full Power, Normal, etc.) and open the
System Power Mode window.
6. Enable the desired Hibernation settings for When I press the power
button and When I close the lid.
7. Click the OK button.
Data save in hibernation mode
When you turn off the power in hibernation mode, the computer takes a moment to
save current memory data to the hard disk. During this time, the Disk indicator will
light.
After you turn off the computer and memory is saved to the hard disk, turn off the
power to any peripheral devices.
3-9
GETTING STARTED
The computer will enter Hibernate mode automatically when you press the power
button or close the lid. First, however, make the appropriate settings according to
the steps below.
User's Manual
CAUTION: Do not turn the computer or devices back on immediately.
Wait a moment to let all capacitors fully discharge.
Standby mode
If you have to interrupt your work, you can turn off the power without exiting from
your software. Data is maintained in the computer’s main memory. When you turn
on the power again, you can continue working right where you left off.
CAUTIONS: 1. Before entering Standby mode, be sure to save your data.
2. Do not install or remove a memory module while the
computer is in standby mode. The computer or the
module could be damaged.
GETTING STARTED
3. Do not remove the battery pack while the computer is in
standby mode (unless the computer is connected to an
AC power source). Data in memory will be lost.
4. If you carry the computer on board an aircraft or into a
hospital, be sure to shut down the computer in hibernation mode or in shutdown mode to avoid radio signal
interference.
Benefits of standby
The standby feature provides the following benefits:
❑
Restores the previous working environment more rapidly than does hibernation.
❑
Saves power by shutting down the system when the computer receives no
input or hardware access for the duration set by the System Standby feature.
❑
You can use the panel power off feature.
Executing standby
NOTE: You can also enable Standby by pressing Fn + F3. See Chapter
5, Keyboard, for details.
You can enter standby mode in one of three ways:
1. Click start, click Turn Off Computer and click Stand by.
3-10
Restarting the computer
2. Close the display panel. This feature must be enabled. Refer to the System
Power Mode item in Power Saver Utility discribed in the Control Panel.
Open Performance and Maintenance and open TOSHIBA Power
Saver.
3. Press the power button. This feature must be enabled. Refer to the System
Power Mode item in Power Saver Utility discribed in the Control Panel.
Open Performance and Maintenance and open TOSHIBA Power
Saver.
When you turn the power back on, you can continue where you left when you shut
down the computer.
NOTES: 1. When the computer is shut down in standby mode, the
power indicator flashes orange.
GETTING STARTED
2. If you are operating the computer on battery power, you
can lengthen the operating time by shutting down in
hibernation mode. Standby mode consumes more power.
Standby limitations
Standby will not function under the following conditions:
❑
Power is turned back on immediately after shutting down.
❑
Memory circuits are exposed to static electricity or electrical noise.
Restarting the computer
Certain conditions require that you reset the system. For example, if:
❑
You change certain computer settings.
❑
An error occurs and the computer does not respond to your keyboard
commands.
There are three ways to reset the computer system:
1. Click start then click Turn Off Computer. From the Turn Off Computer menu select Restert.
2. Press Ctrl + Alt + Del to display the Windows Task Manager, then
select Shutdown and Restart.
3. Select Restart from the Turn Off Computer window in the start
menu.
3-11
User's Manual
4. Press the power button and hold it down for five seconds. Wait 10 to 15
seconds, then turn the power on again by pressing the power button.
Restoring the preinstalled software
from the Product Recovery CD-ROM
If preinstalled files are damaged, use the Product Recovery CD-ROM to restore
them. To restore the operating system and all preinstalled software, follow the steps
below.
GETTING STARTED
CAUTION: When you reinstall the Windows operating system, the hard
disk will be reformatted and all data will be lost.
1. Load the Product Recovery CD-ROM in the fixed optical media drive and
turn off the computer’s power.
2. Hold down the F12 key and turn on the power. When In Touch with
Tomorrow TOSHIBA appears, release the F12 key.
3. Use the left or right cursor key to select the CD-ROM icon in the display
menu. For details, refer to the Boot priority section in Chapter 7, HW Setup.
4. Follow the on-screen instructions.
3-12
Chapter 4
Operating Basics
This chapter gives information on basic operations including using the pointing
devices, USB diskette drive, optical media drives, Sub LCD, audio/video controls,
the microphone, the internal modem, wireless communication, LAN, TOSHIBA
Remote Control and changing Slim Select Bay modules. It also provides tips on
caring for your computer, diskettes and CD/DVDs.
Pointing devices
The configuration, the computer is equipped a Touch Pad as a pointing device.
Using the Touch Pad
To use the Touch Pad, simply touch and move your finger tip across it in the
direction you want the on-screen pointer to go.
OPERATING BASICS
TOUCH PAD
CONTROL
BUTTONS
TOUCH PAD
Figure 4-1 Touch Pad and Touch Pad control buttons
Two buttons below the keyboard are used like the buttons on a mouse pointer.
Press the left button to select a menu item or to manipulate text or graphics designated by the pointer. Press the right button to display a menu or other function
depending on the software you are using.
NOTE: You can also tap the Touch Pad to perform functions similar to
those of the left button.
4-1
User's Manual
Click: Tap the Touch Pad once
Double-click: Tap twice
Drag and drop: Tap to select the material you want to move. Leave your
finger on the Touch Pad after the second tap and move the material.
Using the USB diskette drive
A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44megabyte or 720-kilobyte diskettes. Refer to Chapter 2, Grand Tour, for more
information.
Connecting 3 1/2" diskette drive
To connect the drive, plug the diskette drive connector into a USB port. Refer to
Figure 4-3.
OPERATING BASICS
CAUTION: Make sure the connector is right side up and properly
aligned with the socket. Do not try to force the connection, doing so can
damage the connecting pins.
Figure 4-2 Connecting the USB diskette drive
NOTE: If you connect the diskette drive after turning on the computer, it
will take about 10 seconds for the computer to recognize the drive. Do
not disconnect and reconnect before 10 seconds has elapsed.
4-2
Changing Slim Select Bay modules
Disconnecting 3 1/2" diskette drive
When you have finished using the diskette drive, follow the procedures below to
disconnect it:
1. Wait for the indicator light to go out to make sure all diskette activity has
stopped.
CAUTION: If you disconnect the diskette drive or turn off the power
while the computer is accessing the drive you may lose data or damage
the diskette or the drive.
2. Click the Safety Remove Hardware icon on the Task Bar.
3. Click Diskette drive.
4. Pull the diskette drive connector out of the USB port.
Changing Slim Select Bay modules
CAUTIONS: 1. To avoid injury, do not put your hand into the Slim
Select Bay slot.
2. Before removing or installing a second battery pack,
turn off the computer’s power.
NOTE: The TOSHIBA Mobile Extension is preinstalled to support hot
swapping under Windows. Refer to Chapter 1, Introduction, and to the
utility’s online help files for information on using this utility to change
modules while the computer’s power is on. If you are using a Bridge
media adaptor, you can click the Windows Safety Remove Hardware
icon on the Task Bar to remove the Bridge media adaptor.
Removing a module
Remove the DVD-ROM drive as described below.
1. Check all disk indicators to make sure no disks are operating.
2. Turn the computer upside down.
4-3
OPERATING BASICS
This section explains how to change modules in the Slim Select Bay. The illustrations show replacement of the DVD-ROM drive with the Slim Select Bay HDD
adaptor. Therefore, the text refers to those modules. However, the procedures are
the same for any of the modules: DVD-ROM drive, CD-RW/DVD-ROM drive, DVDR/-RW drive, DVD Multi drive, bridge media adaptor, HDD adaptor.
User's Manual
CAUTION: Wait for all disk indicators to go out before you turn over the
computer and be careful to lay the computer down gently. Shock can
damage the HDD or other components.
3. Slide the Slim Select Bay latch to the unlock position.
4. Grasp the DVD-ROM drive and slide it out.
CAUTION: The DVD-ROM drive and other Slim Select Bay modules can
become hot with use. Be careful when removing the module.
SLIM SELECT BAY
LATCH
SLIM SELECT BAY
MODULE
OPERATING BASICS
Figure 4-3 Removing the Slim Select Bay module
Installing a module
Install the Slim Select Bay HDD adaptor as described below.
1. Insert the Slim Select Bay module in the computer as shown below and press
until the ejector clicks.
SLIM SELECT BAY
MODULE
Figure 4-4 Installing the Slim Select Bay module
4-4
Using optical media drives
Using optical media drives
The text and illustrations in this section refer primarily to the DVD-ROM drive in the
Slim Select Bay. However, operation is the same for the CD-RW/DVD-ROM drive
and the DVD Multi drive in Slim Select Bay. The full-size drive provides highperformance execution of CD/DVD-ROM-based programs. You can run either 12 cm
(4.72") or 8 cm (3.15") CD/DVDs without an adaptor. An ATAPI interface controller
is used for CD/DVD-ROM operation. When the computer is accessing a
CD/DVD, an indicator on the drive glows and the Slim Select Bay indicator glows.
NOTE: Use the WinDVD 4 application to view DVD-Video discs.
If you have a CD-RW/DVD-ROM drive, refer also to the Writing CDs section for
precautions on writing to CDs.
Loading discs
To load CD/DVDs, follow the steps below and refer to figures 4-5 to 4-9.
1. a. When the power is on, press the DVD-ROM eject button to open the
drawer slightly.
OPERATING BASICS
EJECT BUTTON
Figure 4-5 Pressing the DVD-ROM eject button
4-5
User's Manual
b. Pressing the eject button will not open the drawer when the DVD-ROM
drive’s power is off. If the power is off, you can open the drawer by
inserting a slender object (about 15 mm) such as a straightened paper clip
into the eject hole just to the right of the eject button.
15
mm
Diameter 1.0mm
Figure 4-6 Manual release with the eject hole
OPERATING BASICS
2. Pinch the drawer gently and pull until it is fully opened.
Figure 4-7 Pulling the drawer open
4-6
Using optical media drives
3. Lay the CD/DVD, label side up, in the drawer.
Figure 4-8 Inserting a CD/DVD
OPERATING BASICS
NOTE: When the drawer is fully opened, the edge of the computer will
extend slightly over the CD/DVD tray. Therefore, you will need to turn
the CD/DVD at an angle when you place it in the tray. After seating the
CD/DVD, however, make sure it lies flat, as shown in figure 4-8.
CAUTIONS: 1. Do not touch the laser lens. Doing so could cause
misalignment.
2. Be careful to keep foreign matter from entering the
drive. Check the back edge of the tray to make sure it
carries no debris before closing the drive.
4. Press gently at the center of the CD/DVD until you feel it click into place. The
CD/DVD should lie below the top of the spindle, flush with the spindle base.
5. Push the center of the drawer to close it. Press gently until it locks into place.
CAUTION: If the CD/DVD is not seated properly when the drawer is
closed, the CD/DVD might be damaged. Also, the drawer might not open
fully when you press the eject button.
4-7
User's Manual
Figure 4-9 Closing the DVD-ROM drawer
Removing discs
OPERATING BASICS
To remove the CD/DVD, follow the steps below and refer to figure 4-10.
CAUTION: Do not press the eject button while the computer is accessing
the Fixed DVD-ROM drive. Wait for the Disk indicator to go out before
you open the drawer. Also, if the CD/DVD is spinning when you open the
drawer, wait for it to stop before you remove it.
1. To pop the drawer partially open, press the eject button. Gently pull the
drawer out until it is fully opened.
CAUTIONS: 1. When the drawer pops open slightly, wait a moment to
make sure the CD/DVD has stopped spinning before
pulling the drawer fully open.
2. Turn off the power before you use the eject hole. If the
CD/DVD is spinning when you open the drawer, the
CD/DVD could fly off the spindle and cause injury.
2. The CD/DVD extends slightly over the sides of the drawer so you can grasp it.
Hold the CD/DVD gently and lift it out.
4-8
Writing CDs on CD-RW/DVD-ROM drive
Figure 4-10 Removing a CD/DVD
3. Push the center of the drawer to close it. Press gently until it locks into place.
Writing CDs on CD-RW/DVD-ROM
drive
NOTE: CD-R discs can be written to only once. CD-RW discs can be
rewritten many times.
Before writing or rewriting
Please observe the following points when you write or rewrite the data.
❑
We recommend the following manufacturers of CD-R and CD-RW media.
Media quality can affect write or rewrite success rates.
CD-R: TAIYOYUDENCO.,LTD.
Mitsui Chemicals Inc.
MITUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
Hitachi Maxell Ltd.
4-9
OPERATING BASICS
Depending on the type of drive installed, you may be able to write CDs. The CDRW/DVD-ROM drive lets you write as well as read CD-ROMs. Observe the
precautions in this section to ensure the best performance for writing CDs. For
information on loading and unloading CDs refer to the Using optical media drive
section.
User's Manual
CD-RW: MITUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
OPERATING BASICS
TOSHIBA has confirmed the operation of CD-R and CD-RW media of the
manufacturers above. Operation of other media cannot be guaranteed.
❑
CD-RW can generally be rewritten about 1,000 times. However, the actual
number of rewrites is affected by the quality of the media and the way it is
used.
❑
Be sure to connect the universal AC adaptor when you write or rewrite.
❑
Be sure to close all other software programs except the writing software.
❑
Do not run software such as a screen saver which can put a heavy load on the
CPU.
❑
Operate the computer at full power. Do not use power-saving features.
❑
Do not write while virus check software is running. Wait for it to finish, then
disable virus detection programs including any software that checks files
automatically in the background.
❑
Do not use hard disk utilities, including those intended to enhance HDD
access speed. They may cause unstable operation and damage data.
❑
Write from the computer's HDD to the CD. Do not try to write from shared
devices such as a LAN server or any other network device.
❑
Writing with software other than Drag'n Drop CD has not been confirmed.
Therefore, operation with other software cannot be guaranteed.
When writing or rewriting
Note the following when you write or rewrite a CD-R or CD-RW.
❑
Always copy data from the HDD to the CD. Do not use cut-and-paste. The
original data will be lost if there is a write error.
❑
Do not perform any of the following actions:
• Operate the computer for any other function, including use of a mouse or
Touch Pad, closing/opening the LCD panel.
• Start a communication application such as a modem.
• Apply impact or vibration to the PC.
• Install, remove or connect external devices, including the following:
PC card, SD card, USB devices, external display, i.LINK devices, optical
digital devices.
• Use the CD/MP3 control buttons to reproduce music and voice.
4-10
Writing CD/DVDs on DVD-R/-RW drive
• Open the optical media drive.
❑
If the media is poor in quality, dirty or damaged, writing or rewriting errors may
occur.
❑
Set the computer on a level surface and avoid places subject to vibration such
as airplanes trains, or cars. Do not use an unstable surface such as a stand.
❑
Keep mobile phones and other wireless communication devices away from the
computer.
Writing CD/DVDs on DVD-R/-RW
drive
You can use the DVD-R/-RW drive to write data to either CD-R/-RW or DVD-R/RW discs. The following applications for writing are supplied on CD-ROM:
Drag'n Drop CD, licensed by Easy Systems Japan Ltd., and DigiOn Inc., MotionDV
STUDIO, DVDfunSTUDIO and DVD-MovieAlbum, licensed by Matsushita Electric
Industrial Co.,Ltd.
Important message
Disclaimer
TOSHIBA does not bear responsibility for the following:
❑
Damage to any CD-R/-RW or DVD-R/-RW disc that may be caused by writing
or rewriting with this product.
❑
Any change or loss of the recorded contents of CD-R/-RW or DVD-R/-RW
disc that may be caused by writing or rewriting with this product, or for any
business profit loss or business interruption that may be caused by the change
or loss of the recorded contents.
❑
Damage that may be caused by using third party equipment or software.
Given the technological limitations of current optical disc writing drives, you may
experience unexpected writing or rewriting errors due to disc quality or problems
with hardware devices. Also, it is a good idea to make two or more copies of
important data, in case of undesired change or loss of the recorded contents.
4-11
OPERATING BASICS
Before you write or rewrite to CD-R/-RW or DVD-R/-RW disc, read and follow all
set-up and operating instructions in this section. If you fail to do so, the DVD-R/RW drive may not function properly, and you may fail to write or rewrite, lose data
or incur other damage.
User's Manual
Writing CD/DVDs on DVD Multi drive
You can use the DVD Multi drive to write data to either CD-R/-RW or DVD-R/-RW/RAM discs. The following applications for writing are supplied on CD-ROM:
Drag'n Drop CD, licensed by Easy Systems Japan Ltd., and DigiOn Inc., MotionDV
STUDIO, DVDfunSTUDIO and DVD-MovieAlbum, licensed by Matsushita Electric
Industrial Co.,Ltd.
Important message
Before you write or rewrite to CD-R/-RW or DVD-R/-RW/-RAM disc, read and
follow all set-up and operating instructions in this section. If you fail to do so, the
DVD Multi drive may not function properly, and you may fail to write or rewrite,
lose data or incur other damage.
Disclaimer
OPERATING BASICS
TOSHIBA does not bear responsibility for the following:
❑
Damage to any CD-R/-RW or DVD-R/-RW/-RAM disc that may be caused by
writing or rewriting with this product.
❑
Any change or loss of the recorded contents of CD-R/-RW or DVD-R/-RW/RAM disc that may be caused by writing or rewriting with this product, or for
any business profit loss or business interruption that may be caused by the
change or loss of the recorded contents.
❑
Damage that may be caused by using third party equipment or software.
Given the technological limitations of current optical disc writing drives, you may
experience unexpected writing or rewriting errors due to disc quality or problems
with hardware devices. Also, it is a good idea to make two or more copies of
important data, in case of undesired change or loss of the recorded contents.
4-12
Writing CD/DVDs on DVD Multi drive
Read/write function chart
Read
Write
Drag’n Drop CD*1
DVDfunSTUDIO*1
DVD-MovieAlbum*1
DVD-Video*2
DVD VR*2
(DVD VideoRecoding)
CD-R
CD-RW
DVD-R
DVD-RW
DVD-RAM
DVD+R
DVD+RW
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
No
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
No
*1 Software supplied with the product can be used for writing to a disc.
*2 Video format can be written.
4-13
OPERATING BASICS
Disc type
User's Manual
❑
Based on TOSHIBA's limited compatibility testing, we suggest the following
manufacturers of CD-R/-RW and DVD-R/-RW/-RAM disc. However, in no
event does TOSHIBA guarantee the operation, quality or performance of any
disc. Disc quality can affect write or rewrite success rates.
CD-R: TAIYOYUDENCO.,LTD.
Mitsui Chemicals Inc.
MITUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
Hitachi Maxell Ltd.
CD-RW: MITUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
DVD-R: DVD Specifications for Recordable Disc for General Version
2.0
TAIYOYUDENCO.,LTD.
PIONEERVIDEOCORPORATION
MITSUBISHI CHEMICAL CORPORATION
DVD-RW: DVD Specifications for Re-recordable Disc for Version 1.1
VICTOR COMPANY OF JAPAN.LIMITED
OPERATING BASICS
TDK Corporation
DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0 or
Version 2.1
Matsushita Electric Industrial Co., Ltd.
❑
If the disc is poor in quality, dirty or damaged, writing or rewriting errors may
occur. Be careful to check the disc for dirt or damage before you use it.
❑
The actual number of rewrites to CD-RW or DVD-RW/-RAM is affected by the
quality of the disc and the way it is used.
❑
There are two types of DVD discs: authoring and general use discs. Do not use
authoring discs. Only general use discs can be written to by a computer drive.
❑
You can use DVD-RAM discs that can be removed from a cartridge and
DVDRAM discs designed without a cartridge. You cannot use a disc with a 2.6
GB single-sided capacity or 5.2 GB double-sided capacity.
❑
Other DVD-ROM drives for computers or other DVD players may not be able
to read DVD-R/-RW discs.
❑
You cannot add data to a DVD-R/-RW disc that has previously been written to.
❑
You cannot overwrite data that has been previously written to a DVD-RW disc.
❑
You cannot partially delete any data written to a DVD-RW disc.
4-14
Writing CD/DVDs on DVD Multi drive
❑
Data written to a CD-R/DVD-R disc cannot be deleted either in whole or in part.
❑
Data deleted (erase) from a CD-RW and DVD-RW/-RAM disc cannot be
recovered. Check the content of the disc carefully before you delete it. If
multiple drives that can write data to discs are connected, be careful not to
delete data from the wrong drive.
❑
In writing to a DVD-R/-RW disc, some disc space is required for file
management, so you may not be able to write the full capacity of the disc.
❑
Since the disc is based on the DVD standard, it will be filled with dummy data if
the written data is less than about 1 GB. Even if you write only a small amount
of data, it will take time to fill in the dummy data.
❑
Two types of DVD-R/-RW/-RAM discs are on the market: data and video. Use
a video disc to store video data. You can use video discs on a DVD recorder as
well as on your computer's DVD-ROM drive. You cannot use data discs on a
DVD recorder.
❑
DVD-RAM formatted by FAT32 cannot be read in Windows 2000 without
DVD-RAM Driver Software.
Before writing or rewriting
Please observe the following points when you write or rewrite data.
When multiple drives that can write data to discs are connected, be careful not
to write to the wrong drive.
❑
Be sure to connect the universal AC adaptor before you write or rewrite.
❑
Before you enter standby/hibernation mode, be sure to finish DVD-RAM
writing. Writing is finished if you can eject DVD-RAM media.
❑
Be sure to close all other software programs except the writing software.
❑
Do not run software such as a screen saver, which can put a heavy load on the
CPU.
❑
Operate the computer in the full-power mode. Do not use power-saving
features.
❑
Do not write while virus check software is running. Wait for it to finish, then
disable virus detection programs including any software that checks files
automatically in the background.
❑
Do not use hard disk utilities, including those intended to enhance HDD
access speed. They may cause unstable operation and data damage.
❑
Write from the computer's HDD to the CD/DVD. Do not try to write from shared
devices such as a LAN server or any other network device.
4-15
OPERATING BASICS
❑
User's Manual
❑
Writing with software other than Drag'n Drop CD, DVDfunSTUDIO and
DVDMovieAlbum is not recommended.
When writing or rewriting
Please observe/consider the following when you write or rewrite to a CD-R/-RW or
DVD-R/-RW/-RAM disc.
❑
Do not perform any of the following actions when writing or rewriting:
• Operate the computer for any other function, including using a mouse or
Touch Pad or closing/opening the LCD panel.
• Start a communication application such as a modem.
• Apply impact or vibration to the computer.
• Install, remove or connect external devices, including the following:
PC card, SD card, USB devices, external display, i.LINK devices, optical
digital devices.
• Use the Audio/Video control button to reproduce music or voice.
OPERATING BASICS
• Open the DVD Multi drive
❑
Do not use standby/hibernation while writing or rewriting.
❑
Make sure writing or rewriting is completed before going into standby/
hibernation. Writing is completed if you can open the DVD Multi drive tray.
❑
Set the computer on a level surface and avoid places subject to vibration such
as airplanes, trains, or cars. Do not use an unstable surface such as a stand.
❑
Keep mobile phones and other wireless communication devices away from the
computer.
❑
Always copy data from the HDD to the DVD-RAM. Do not use cut-and-paste.
The original data will be lost if there is a write error.
Drag’n Drop CD
Note the following limitations when you use Drag'n Drop CD:
❑
DVD-Video cannot be created using Drag'n Drop CD.
❑
DVD-Audio cannot be created using Drag'n Drop CD.
❑
You cannot use Drag'n Drop CD's music CD function to record music to a
DVD-R/-RW disc.
4-16
Writing CD/DVDs on DVD Multi drive
❑
Do not use the DISC Backup function of Drag'n Drop CD to copy DVD-Video
and DVD-ROM with copyright protection, because the copy will not play
correctly.
❑
DVD-RAM disc cannot be backed up with the DISC Backup function of Drag'n
Drop CD.
❑
You cannot backup a CD-ROM or CD-R/-RW to DVD-R/-RW using the DISC
Backup function of Drag'n Drop CD.
❑
You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW to CD-R/-RW
using the DISC Backup function of Drag'n Drop CD.
❑
Drag'n Drop CD cannot record in packet format.
❑
You might not be able to use the DISC backup function of Drag'n Drop CD to
back up a DVD-R/-RW disc that was made with other software on a different
DVD-R/-RW recorder.
Data Verification
To verify that data is written or rewritten correctly, follow the steps below before
you write or rewrite a Data CD/DVD.
1. Right-click Data BOX and select Options to display the DATA DISC
Option window.
3. Click the OK button.
The “Record and Verify” function automatically checks whether data has been
correctly recorded onto a CD/DVD. "Byte compare" compares the original data file
with the data recorded on the CD/DVD and checks that the data completely
matches.
Video (DVD-R/-RW/-RAM)
Note the following limitations when you write video to DVD:
❑
When installing, uninstalling or MotionDV STUDIO, DVDfunSTUDIO or
DVDMovieAlbum, the computer should be set to system administrator or
equivalent privilege.
❑
Whether MotionDV STUDIO and DVD-MovieAlbum use NTSC or PAL format
is determined when the application is installed. To change the format, you will
have to reinstall MotionDV STUDIO and DVD-MovieAlbum.
4-17
OPERATING BASICS
2. Mark the Record and Verify check box and select Byte compare.
OPERATING BASICS
User's Manual
❑
When Drag'n Drop or similar software is resident in the computer's memory, the
DVD Multi drive locks. In this situation, other software cannot be used to write
data to the disc.
❑
While you are editing DVD-R/-RW/-RAM, you can display previews.
However, if an application other than WinDVD is running, the preview might
not display properly. To ensure proper display of previews, do not start other
applications while you are editing DVD-R/-RW/-RAM disc.
❑
Do not change the resolution or the number of screen colors while MotionDV
STUDIO, DVDfunSTUDIO or DVD-MovieAlbum is running.
❑
Although the online manual and Help files indicate that JPEG files can be used,
in fact, they cannot be used.
❑
8cm (3.15") DVD-R/-RW discs cannot be use with DVDfunSTUDIO.
❑
DVDfunSTUDIO cannot make DVD-Audio, VideoCD, and miniDVD.
❑
DVD-R/-RW discs cannot be written in VR format.
❑
It may take several hours for DVDfunSTUDIO to convert video to MPEG
format, and several hours more to save the MPEG file to a DVD Multi drive.
❑
In order to write to a DVD-RW disc that has already been written to using
DVDfunSTUDIO, you will first have to delete all of the data with Drag'n Drop
CD or similar software.
❑
You will need at least 20 GB of empty hard disk space to write to a DVD-R/-RW
disc.
❑
You cannot record in DVD-Video format on a DVD-RAM disc.
❑
You will need to format a DVD-RAM for UDF2.0 using a formatting tool, before
you write to DVD-RAM using DVD-MovieAlbum.
❑
You cannot edit DVD-RAM video data that has copyright protection, using
DVD-MovieAlbum.
❑
You can add PAL format images only to a PAL type DVD-RAM and NTSC
format images only to an NTSC-type DVD-RAM.
❑
You cannot convert a PAL format DVD-RAM to NTSC format or an NTSC type
DVD-RAM to PAL format.
4-18
Media care
Media care
This section provides tips on protecting data stored on your CD/DVDs and
diskettes.
Handle your media with care. The following simple precautions will increase the
lifetime of your media and protect the data stored on them:
CD/DVDs
1. Store your CD/DVDs in the container they came in to protect them and keep
them clean.
2. Do not bend the CD/DVD.
3. Do not write on, apply a sticker to, or otherwise mar the surface of the
CD/DVD that contains data.
4. Hold the CD/DVD by its outside edge or the edge on the center hole. Fingerprints on the surface can prevent the drive from properly reading data.
5. Do not expose to direct sunlight, extreme heat or cold. Do not place heavy
objects on your CD/DVDs.
Diskettes
1. Store your diskettes in the container they came in to protect them and keep
them clean. If a diskette is dirty, do not use cleaning fluid. Clean it with a soft
damp cloth.
2. Do not slide back the diskette’s protective metal covering or touch the
diskette’s magnetic surface. Fingerprints may prevent the diskette drive from
reading data from the diskette.
3. Data may be lost if the diskette is twisted; bent; or exposed to direct sunlight,
extreme heat or cold.
4. Do not place heavy objects on your diskettes.
5. Do not eat, smoke, or use erasers near your diskettes. Foreign particles inside
the diskette’s jacket can damage the magnetic surface.
4-19
OPERATING BASICS
6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry cloth.
Wipe from the center out, do not wipe in a circular direction around the CD/
DVD. If necessary, use a cloth dampened in water or a neutral cleaner. Do not
use benzine, thinner or similar cleaner.
User's Manual
6. Magnetic energy can destroy the data on your diskettes. Keep your diskettes
away from speakers, radios, television sets and other sources of magnetic
fields.
Modem
This section describes how to connect and disconnect the internal modem to and
from a telephone jack.
NOTE: The internal modem does not support voice functions. All data
and fax functions are supported.
CAUTIONS: 1. In case of a lightning storm, unplug the modem cable
from the telephone jack.
2. Do not connect the modem to a digital telephone line.
A digital line will damage the modem.
Region selection
OPERATING BASICS
Telecommunication regulations vary from one region to another, so you will need to
make sure the internal modem’s settings are correct for the region in which it will be
used.
To select a region, follow the steps below.
1. Click start, point to All Programs, point to TOSHIBA Internal Modem
and click Region Select Utility.
NOTE: Do not use the Country/Region Select function in the Modem
setup utility in the Control Panel if the function is available. If you
change the Country/Region in the Control Panel, the change may not
take effect.
2. The Region Selection icon will appear in the Windows Task Bar.
4-20
Modem
Figure 4-11 The Region Selection icon
3. Click the icon with the primary mouse button to display a list of regions that
the modem supports. A sub menu for telephony location information will also
be displayed. A check will appear next to the currently selected region and
telephony location.
4. Select a region from the region menu or a telephony location from the submenu.
• When you click a region it becomes the modem’s region selection, and the
New Location for telephony will be set automatically.
• When you select a telephony location, the corresponding region is automatically selected and it becomes the modem’s current region setting.
Properties menu
Click the icon with the secondary mouse button to display the following menu.
OPERATING BASICS
Figure 4-12 The menu list
4-21
User's Manual
Setting
You can enable or disable the following settings:
AutoRun Mode
The Region Select utility starts automatically when you start up the operating
system.
Open the Dialing Properties dialog box after selecting region.
The dialing properties dialog box will be displayed automatically after you
select the region.
Location list for region selection.
A submenu appears displaying location information for telephony.
Open dialog box, if the modem and Telephony Current
Location region code do not match.
OPERATING BASICS
A warning dialog box is displayed if current settings for region code and
telephony location are incorrect.
Modem Selection
If the computer cannot recognize the internal modem, a dialog box is displayed.
Select the COM port for your modem to use.
Dialing Properties
Select this item to display the dialing properties.
CAUTION: If you are using the computer in Japan, the Telecommunications Business Law requires that you select Japan region mode. It is
illegal to use the modem in Japan with any other selection.
Connecting
To connect the internal modem cable, follow the steps below.
1. Plug one end of the modular cable into the modem jack.
2. Plug the other end of the modular cable into a telephone jack.
4-22
Wireless communications
Figure 4-13 Connecting the internal modem
CAUTION: Do not pull on the cable or move the computer while the
cable is connected.
NOTE: If you use a storage device such as a DVD-ROM drive,
CD-RW/DVD-ROM drive or HDD connected to a 16-bit PC card, you
might experience the following modem problems:
1. Modem speed is slow or communication is interrupted.
2. Skips may occur in sound.
OPERATING BASICS
Disconnecting
To disconnect the internal modem cable, follow the steps below.
1. Pinch the lever on the connector in the telephone jack and pull out the
connector.
2. Disconnect the cable from the computer in the same manner.
Wireless communications
The computer’s wireless communication function supports both wireless LAN and
Bluetooth devices.
Wireless LAN
The wireless LAN is compatible with other LAN systems based on Direct Sequence
Spread Spectrum radio technology that complies with IEEE802.11 wireless LAN
standard (Revision A or B) and Turbo Mode. It supports the following features:
4-23
User's Manual
❑
Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36,
24, 18, 12, 9 and 6Mbit/s. (Revision A)
❑
Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2
and 1Mbit/s. (Revision B)
❑
Automatic Transmit Rate Select mechanism in the transmit range of 108, 96.72,
48, 36, 24, 18 and 12Mbit/s. (Turbo Mode)
❑
Frequency Channel Selection (Revision A/Turbo Mode:5GHz, Revision B:
2.4GHz)
❑
Roaming over multiple channels
❑
Card Power Management
❑
Wired Equivalent Privacy (WEP) data encryption, based on the 152 bit RC4
encryption algorithm.
❑
Advanced Encryption Standard (AES) data encryption, based on 256bit
encryption algorithm.
Wake-up on LAN does not function on a wireless LAN.
OPERATING BASICS
Security
1. Be sure to enable WEP (encryption) function. Otherwise your computer will
allow the illegal access by outsider through wireless LAN to cause illegal
intrusion, eavesdropping, and loss or destruction of stored data. TOSHIBA
strongly recomend the customer to enable the WEP function.
2. TOSHIBA is not liable for the eavesdropping of data due to the use of
wireless LAN and the damage thereof.
Bluetooth wireless technology
Bluetooth™ wireless technology eliminates the need for cables between electronic
devices such as desktop computers, printers and mobile phones.
You cannot use the built-in Bluetooth functions and an optional Bluetooth PC card
simultaneously.
Bluetooth wireless technology has the following features:
Worldwide operation
The Bluetooth radio transmitter and receiver operates in the 2.45 GHz band, which is
license-free and compatible with radio systems in most countries in the world.
4-24
Wireless communications
Radio links
You can easily establish links between two or more devices. The link is maintained
even if the devices are not within line of sight.
Security
Two advanced security mechanisms ensure a high level of security:
❑
Authentication prevents access to critical data and makes it impossible to
falsify the origin of a message.
❑
Encryption prevents eavesdropping and maintains link privacy.
Wireless communication switch
You can enable or disable wireless LAN and Bluetooth functions, with the on/off
switch. No transmissions are sent or received when the switch is off. Slide the
switch toward the back of the computer to turn it on and toward the front of the
computer to turn it off.
CAUTION: Set the switch to off in airplanes and hospitals. Check the
indicator. It will stop glowing when the wireless communication function
is off.
The wireless communication indicator indicates the status of the wireless communication functions.
Indicator status Indication
Indicator off
Wireless communication switch is set to off.
Automatic power down because of overheating.
Power malfunction
Indicator glows
Wireless communication switch is on.
Wireless LAN or Bluetooth is turned on by an application.
If you used the Task Bar to disable W-LAN, restart the computer or follow the
procedures below to enable the system to recognize W-LAN. Open or click the
following: start, Control Panel, System, Hardware Device Manager,
Network adapters, TOSHIBA Wireless LAN Mini PCI Card and enable.
4-25
OPERATING BASICS
Wireless communication Indicator
User's Manual
LAN
The computer has built-in support for Ethernet LAN (10 megabits per second,
10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx).
This section describes how to connect/disconnect to a LAN.
CAUTION: Do not install or remove an optional memory module while
Wake-up on LAN is enabled.
NOTE: The Wake-up on LAN function consumes power even when the
system is off. Leave the universal AC adaptor connected while using this
feature.
Connecting LAN cable
CAUTION: The computer must be configured properly before connecting
to a LAN. Logging onto a LAN using the computer’s default settings
could cause a malfunction in LAN operation. Check with your LAN
administrator regarding set-up procedures.
OPERATING BASICS
If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-TX), be
sure to connect with a CAT5 cable. You cannot use a CAT3 cable.
If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can
connect with either a CAT5 or a CAT3.
To connect the LAN cable, follow the steps below.
1. Turn off the power to the computer and to all external devices connected to
the computer.
2. Plug one end of the cable into the LAN jack. Press gently until you hear the
latch click into place.
4-26
Figure 4-14 Connecting the LAN cable
Cleaning the computer
3. Plug the other end of the cable into a LAN hub connector. Check with your
LAN administrator before connecting to a hub.
NOTE: When the computer is exchanging data with the LAN, the LAN
Active indicator glows yellow. When the computer is connected to a
LAN hub but is not exchanging data, the Link indicator glows green.
Disconnecting LAN cable
To disconnect the LAN cable, follow the steps below.
CAUTION: Make sure the LAN Active indicator (yellow LED) is out
before you disconnect the computer from the LAN.
1. Pinch the lever on the connector in the computer’s LAN jack and pull out the
connector.
2. Disconnect the cable from the LAN hub in the same manner. Check with your
LAN administrator before disconnecting from the hub.
Cleaning the computer
❑
Be careful not to spill liquids into the computer. If the computer does get wet,
turn the power off immediately and let the computer dry completely before you
turn it on again.
❑
Clean the computer using a slightly damp (with water) cloth. You can use glass
cleaner on the display. Spray a small amount of cleaner on a soft, clean cloth
and wipe the screen gently with the cloth.
CAUTION: Never spray cleaner directly onto the computer or let liquid
run into any part of it. Never use harsh or caustic chemical products to
clean the computer.
❑
Remove the dust from the air filter on the underside of the computer regularly
with vacuum cleaner. See Chapter 2 Grand Tour, Underside.
4-27
OPERATING BASICS
To help ensure long, trouble-free operation, keep the computer free of dust and use
care with liquids around the computer.
User's Manual
Moving the computer
The computer is designed for rugged durability. However, a few simple precautions
taken when moving the computer will help ensure trouble-free operation.
❑
Make sure all disk activity has ended before moving the computer. Check the
Disk and Slim Select Bay indicators on the computer.
❑
If a CD/DVD is in the drives, remove it. Also make sure the drawer is securely
closed.
❑
Turn off the power to the computer.
❑
Disconnect the universal AC adaptor and all peripherals before moving the
computer.
❑
Close the display. Do not pick up the computer by its display panel.
❑
Close all port covers.
❑
Use the carrying case when transporting the computer.
OPERATING BASICS
Heat dispersal
To protect from overheating, the CPU has an internal temperature sensor. If the
computer’s internal temperature rises to a certain level, the cooling fan is turned on
or the processing speed is lowered. You can select whether to control the CPU
temperature by turning on the fan first, then if necessary, lowering the CPU speed.
Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the
Cooling Method item of the Power Save Mode window in TOSHIBA Power Saver.
Maximum
Performance
Turn on the fan first, then if necessary, lower the CPU
processing speed.
Performance
Use a combination of the fan and lowering the CPU
processing speed.
Battery optimized
Lower the CPU processing speed first, then if necessary
turn on the fan.
When the CPU temperature falls to a normal range, the fan is turned off and the CPU
operation returns to standard speed.
NOTE: If the CPU temperature reaches an unacceptably high level with
either setting, the system automatically shuts down to prevent damage.
Data in memory will be lost.
4-28
Chapter 5
The Keyboard
The computer’s keyboard layouts are compatible with a 101/102-key enhanced
keyboard. By pressing some keys in combination, all the 101/102-key keyboard
functions can be executed on the computer.
The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages
are available.
There are five types of keys: typewriter keys, keypad overlay, function keys, soft
keys and cursor control keys.
Typewriter keys
The typewriter keys, produce the upper- and lower-case letters, numbers, punctuation marks, and special symbols that appear on the screen.
There are some differences, however, between using a typewriter and using a
computer keyboard:
Letters and numbers produced in computer text vary in width. Spaces, which
are created by a “space character,” may also vary depending on line justification and other factors.
❑
The lowercase l (el) and the number 1 (one) are not interchangeable on
computers as they are on a typewriter.
❑
The uppercase O (oh) and the 0 (zero) are not interchangeable.
❑
The Caps Lock function key locks only the alphabetic characters in uppercase while the shift lock on a typewriter places all keys in the shifted position.
❑
The Shift keys, the Tab key, and the BkSp (backspace) key perform the
same function as their typewriter counterparts but also have special computer
functions.
5-1
THE KEYBOARD
❑
User's Manual
F1 … F12 function keys
The function keys, not to be confused with Fn, are the 12 keys at the top of your
keyboard. These keys function differently from other keys.
F1 through F12 are called function keys because they execute programmed
functions when pressed. Used in combination with the Fn key, keys marked with
icons execute specific functions on the computer. See the section, Soft keys: Fn key
combinations, in this chapter. The function executed by individual keys depends on
the software you are using.
Soft keys: Fn key combinations
The Fn (function) is unique to TOSHIBA computers and is used in combination
with other keys to form soft keys. Soft keys are key combinations that enable,
disable or configure specific features.
NOTE: Some software may disable or interfere with soft-key operations.
Soft-key settings are not restored by the Standby feature.
Emulating keys on enhanced keyboard
Esc
F1
~
CapsLock
Shift
W
A
E
S
Z
F4
$
4
#
3
2
Q
Tab
THE KEYBOARD
@
!
1
`
F3
F2
%
5
R
D
X
F5
F
C
Y
G
V
U
I
J
N
F8
(
9
8
H
B
F7
*
&
7
^6
T
F6
)
0
O
K
M
F10
_
-
+
=
{
[
P
>
.
?
/
PrtSc
SysReg
Scroll
lock
Pause
Break
Bk Sp
Ins
Home
PgUp
Num
Lock
End
PgDn
7
Home
8
\
Del
9
PgUp
4
5
6
1
End
2
3
PgDn
F11
F12
}
]
,,
,
:
;
L
<
,
F9
/
*.
+
Enter
Shift
Enter
Ctrl
Alt
Alt
Ctrl
Figure 5-1 A 101-key enhanced keyboard layout
5-2
0
Ins
.
Del
Soft keys: Fn key combinations
The keyboard is designed to provide all the features of the 101-key enhanced
keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric
keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of
the main keyboard. Since the keyboard is smaller and has fewer keys, some of the
enhanced keyboard functions must be simulated using two keys instead of one on
the larger keyboard.
Your software may require you to use keys that the keyboard does not have.
Pressing the Fn key and one of the following keys simulates the enhanced
keyboard’s functions.
Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the
keys with gray markings on the bottom edge become numeric keypad keys (Fn +
F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this
chapter for more information on how to operate these keys. The power on default
for both settings is off.
Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on
default is off.
Press Fn + Enter to simulate Enter on the enhanced keyboard’s numeric keypad.
THE KEYBOARD
Press Fn + Ctrl to simulate the enhanced keyboard’s right Ctrl key.
5-3
User's Manual
Hot keys
Hot keys (Fn + a function or Esc key) let you enable or disable certain features of
the computers.
Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or
off. When you press these hot keys, the current setting will change and be
displayed as an icon.
Instant security: Press Fn + F1 to blank the screen to prevent others from
accessing your data. To restore the screen and original settings, press any key or
press the Touch Pad. If a screensaver password is registered, a dialog box will
appear. Enter the screensaver password and click OK. If no password is set, the
screen will be restored when you press any key or press the Touch Pad.
THE KEYBOARD
Power save mode: Pressing Fn + F2 changes the power save mode.
If you press Fn + F2 in a Windows environment, the Power Save Mode is
displayed in a dialog box similar to the one below. Continue holding down Fn and
press F2 again to change the setting. You can also change this setting through the
Plugged in or Running on batteries item of the Power Saver Properties window in
Power Saver.
5-4
Soft keys: Fn key combinations
Standby: When you press Fn + F3, the computer enters Standby. To avoid
entering Standby unexpectedly, a dialog box appears for verification. However, if
you select the check box, it will not appear in the future.
Hibernation: When you press Fn + F4, the computer enters Hibernation. To
avoid entering Hibernation unexpectedly, a dialog box appears for verification.
However, if you select the check box, it will not appear in the future.
Display selection: Press Fn + F5 to change the active display device. When you
press these hot keys, a dialog box appears. Only selectable devices will be displayed. Hold down Fn and press F5 again to change the device. When you release
Fn and F5, the selected device will change. If you hold down these hot keys for five
seconds the selection will return to LCD.
5-5
THE KEYBOARD
LCD Display Brightness: Pressing Fn + F6 decreases the display brightness in
decrements. When you press these hot keys, the current setting will be displayed
for two seconds by an icon. You can also change this setting through the Monitor
brightness item of the Power Save Mode window in Power Saver.
User's Manual
LCD Display Brightness: Pressing Fn + F7 increases the display brightness in
increments. When you press these hot keys, the current setting will be displayed
for two seconds by a pop-up icon. You can also change this setting through the
Monitor brightness item of the Power Save Mode window in Power Saver.
NOTES: 1. The brightness level is always set at the maximum value for
about 18 seconds, when the LCD turns on. After 18
seconds, the brightness level will appear at the Power
Save Mode setting or you can change it manually.
2. Display clarity increases with the brightness level.
Wireless setting: If your computer has both Bluetooth and wireless LAN
functions, you can press Fn + F8 to select which type of wireless communication
you want to use. When you press these hot keys, a dialog box will appear.
Continue holding down Fn and press F8 to change the setting. If wireless
communication is turned off, Disabled Wireless Communication
Switch will be displayed.
THE KEYBOARD
NOTE: If no wireless communication device is installed, no dialog box
will not appear.
Touch Pad: Pressing Fn + F9 in a windows environment enables or disables the
Touch Pad function. When you press these hot keys, the current setting will
change and be displayed as an icon.
5-6
Windows special keys
Fn Sticky key
You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is,
you can press it once, release it, and they press an “F number” key. To start the
TOSHIBA Accessibility Utility, click start, point to All Programs, point to
TOSHIBA Utilities and click Accessibility.
Windows special keys
The keyboard provides two keys that have special functions in Windows : one
activates the start menu and the other has the same function as the secondary
mouse button.
This key activates the Windows start menu.
This key has the same function as the secondary mouse button.
Keypad overlay
Your computer’s keyboard does not have an independent numeric keypad, but its
numeric keypad overlay functions like one.
The keys in the center of the keyboard with gray letters make up the numeric
keypad overlay. The overlay provides the same functions as the numeric keypad
on the 101/102-key enhanced keyboard in figure 5-2.
The numeric keypad overlay can be used for numeric data input or cursor and page
control.
Arrow mode
To turn on the Arrow mode, press Fn + F10. The Arrow mode F10 indicator
lights. Now try cursor and page control using the keys shown in figure 5-2. Press
Fn + F10 again to turn off the overlay.
5-7
THE KEYBOARD
Turning on the overlays
User's Manual
Numeric mode
To turn on the Numeric mode, press Fn + F11. The Numeric mode F11 indicator
lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11
again to turn off the overlay.
Figure 5-2 The numeric keypad overlay
THE KEYBOARD
Temporarily using normal keyboard (overlay
on)
While using the overlay, you can temporarily access the normal keyboard without
turning off the overlay:
1. Hold Fn and press any other key. All keys will operate as if the overlay were
off.
2. Type upper-case characters by holding Fn + Shift and pressing a character
key.
3. Release Fn to continue using the overlay.
5-8
Generating ASCII characters
Temporarily using overlay (overlay off)
While using the normal keyboard, you can temporarily use the keypad overlay
without turning it on:
1. Press and hold down Fn.
2. Check the keyboard indicators. Pressing Fn turns on the most recently used
overlay. If the Numeric mode indicator lights, you can use the overlay for
numeric entry. If the Arrow mode indicator lights, you can use the overlay for
cursor and page control.
3. Release Fn to return to normal keyboard operation.
Temporarily changing modes
If the computer is in Numeric mode, you can switch temporarily to Arrow
mode by pressing a shift key.
If the computer is in Arrow mode, you can switch temporarily to Numeric
mode by pressing a shift key.
Generating ASCII characters
Not all ASCII characters can be generated using normal keyboard operation. But,
you can generate these characters using their ASCII codes.
With the overlay on:
1. Hold down Alt.
2. Using the overlay keys, type the ASCII code.
3. Release Alt, and the ASCII character appears on the display screen.
With the overlay off:
1. Hold down Alt + Fn.
THE KEYBOARD
2. Using the overlay keys, type the ASCII code.
3. Release Alt + Fn, and the ASCII character appears on the display screen.
5-9
THE KEYBOARD
User's Manual
5-10
Power and Power-Up Modes
The computer’s power resources include the universal AC adaptor and internal
batteries. This chapter gives details on making the most effective use of these
resources including charging and changing batteries, tips for saving battery power,
and power up modes.
Power conditions
The computer’s operating capability and battery charge status are affected by the
power conditions: whether a universal AC adaptor is connected, whether a battery
is installed and what the charge level is for the battery.
Table 6-1 Power conditions
Power on
universal
Battery
AC adaptor fully
connected
charged
Battery
• Operates
• LED: Battery green
Power off (no operation)
• LED:
Battery green
DC IN green
DC IN green
• Operates
• Quick charge
partially
• Quick charge
• LED: Battery orange
charged
• LED: Battery orange
or no charge
DC IN green
DC IN green
No
• Operates
• No charge
battery
• No charge
• LED: Battery off
installed
• LED: Battery off
DC IN green
DC IN green
6-1
POWER AND
POWER-UP MODES
Chapter 6
POWER AND
POWER-UP MODES
User's Manual
Table 6-1 Power conditions continued
Power on
AC
Battery
• Operates
adaptor
charge is
• LED: Battery off
not
above low
connected
battery
Power off (no operation)
DC IN off
trigger point
Battery
• Operates
charge is
• LED: Battery
below low
flashes orange
battery
DC IN off
trigger point
Battery
Computer goes
charge is
into resume mode
exhausted
shuts down
No
• Cannot operate
battery
• LED: Battery off
installed
DC IN off
Power indicators
As shown in the above table, the Battery, Slim Select Bay, DC IN and Power
indicators on the system indicator alert you to the computer’s operating capability
and battery charge status.
Battery indicators
Check the Battery indicator to determine the status of the battery pack. The
following indicator lights indicate the battery status:
Flashing orange
Orange
6-2
The battery charge is low. The universal AC adaptor must
be connected to recharge the battery.
Indicates the universal AC adaptor is connected and
charging the battery.
Green
Indicates the universal AC adaptor is connected and the
battery is fully charged.
No light
Under any other conditions, the indicator does not light.
Battery types
DC IN indicator
Check the DC IN indicator to determine the power status with the universal AC
adaptor connected:
Green
Flashing orange
No light
Indicates the universal AC adaptor is connected and
supplying proper power to the computer.
Indicates a problem with the power supply. Plug the
universal AC adaptor into another outlet. If it still does not
operate properly, see your dealer.
Under any other conditions, the indicator does not light.
Power indicator
Check the Power indicator to determine the power status:
Green
Indicates power is being supplied to the computer and the
computer is turned on.
Blinking orange
Indicates power is being supplied to the computer while
the computer is in Standby mode. The indicator turns on
for one second and off for two seconds.
No light
Under any other conditions, the indicator does not light.
Battery types
The computer has two types of batteries:
❑
Battery pack
❑
Real Time Clock (RTC) battery
Battery pack
When the universal AC adaptor is not connected, the computer’s main power
source is a removable lithium ion battery pack, also referred to in this manual as the
battery pack. You can purchase additional battery packs for extended use of the
computer away from an AC power source.
6-3
POWER AND
POWER-UP MODES
NOTE: If the battery becomes too hot while it is being charged, the
charge will stop and the battery indicator will go out. When the battery’s
temperature falls to a normal range, charge will resume. This occurs
whether the computer’s power is on or off.
POWER AND
POWER-UP MODES
User's Manual
Before you remove the battery pack, set the computer to Hibernation mode or save
your data and shut down the computer. Do not change the battery pack while the
universal AC adaptor is connected.
CAUTIONS: 1. The battery pack is a lithium ion battery, which can
explode if not properly replaced, used, handled or
disposed of. Dispose of the battery as required by local
ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements.
2. Do not remove the battery pack while the computer is
in Standby mode. Data is stored in RAM, so if the
computer loses power it will be lost. When the computer is powered off in Standby mode, and the
universal AC adaptor is not connected, the battery
pack supplies power to maintain data and program in
memory. If the battery pack is completely discharged,
Standby mode does not function and the computer
loses all data in memory.
To ensure that the battery pack maintains its maximum capacity, operate the
computer on battery power at least once a month until the battery pack is fully
discharged. Refer to Extending battery life in this chapter for procedures. If the
computer is continuously operated on AC power through a universal AC adaptor
for an extended period, more than a month, the battery may fail to retain a charge. It
may not function efficiently over the expected life of the battery and the Battery
indicator may not indicate a low-battery condition.
Real Time Clock battery
The Real Time Clock (RTC) battery provides power for the internal real time clock
and calendar. It also maintains the system configuration.
If the RTC battery becomes completely discharged, the system loses this data and
the real time clock and calendar stop working. The following message appears when
you turn on the power:
**** RTC battery is low or CMOS checksum is inconsistent ****
Press [F1] key to set Date/Time.
6-4
Care and use of the battery pack
POWER AND
POWER-UP MODES
CAUTION: The computer’s RTC battery is a lithium ion battery and
should be replaced only by your dealer or by a TOSHIBA service
representative. The battery can explode if not properly replaced, used,
handled or disposed of. Dispose of the battery as required by local
ordinances or regulations.
Care and use of the battery pack
The battery pack is a vital component of portable computing. Taking proper care of
it will help ensure longer operating time on battery power as well as a longer life for
your battery pack. Follow the instructions in this section carefully to ensure safe
operation and maximum performance.
Safety precautions
Mishandling of batteries can cause death, serious injury or property damage.
Carefully observe the following advisories:
Danger: Indicates an imminently hazardous situation, which could result in death
or serious injury, if you do not follow instructions.
Warning: Indicates a potentially hazardous situation, which could result in death
or serious injury, if you do not follow instructions.
Caution: Indicates a potentially hazardous situation, which if not avoided, may
result in moderate or minor injury or property damage.
Note: Provides important information.
Danger
1. Never try to dispose of the battery pack by burning or expose it to a heating
device such as a microwave oven. The battery pack could explode and cause
bodily injury.
2. Never try to disassemble, repair or otherwise tamper with a battery pack. The
battery pack will overheat and ignite. Leakage of caustic alkaline solution or
other electrolytic substances will cause fire or injury, possibly resulting in
death or serious injury.
3. Never short-circuit the battery pack by contacting the terminals with a metal
object. A short-circuit can cause fire or otherwise damage the battery pack and
possibly cause injury. To avoid accidental short-circuit, always wrap the
battery pack in plastic and cover the terminals with electrical tape when storing
or disposing of the battery pack.
6-5
POWER AND
POWER-UP MODES
User's Manual
4. Never puncture the battery pack with a nail or other sharp object. Never strike
it with a hammer or other object. Never step on it.
5. Never try to charge the battery pack in any manner other than that described
in the user’s manual. Never connect the battery pack to a plug socket or to a
automobile’s cigarette lighter socket. It may rupture or ignite.
6. Use only the battery pack supplied with the computer or other device or an
battery pack approved by the computer or device’s manufacturer. Battery
packs have different voltages and terminal polarities. Use of an improper
battery could cause smoke, fire or rupture of the battery pack.
7. Never subject a battery pack to heat, such as storage near a heat source.
Exposure to heat can cause the battery pack to ignite, explode or leak caustic
liquid and cause death or serious injury. It could also fail or malfunction
causing data loss.
8. Never expose the battery pack to abnormal shock, vibration or pressure. The
battery pack’s internal protective device will fail, causing it to overheat,
explode, ignite or leak caustic liquids possibly resulting in death or serious
injury.
9. Never let a battery pack become wet. A wet battery pack will overheat, ignite
or rupture possibly resulting in death or serious injury.
Warning
1. Never allow caustic electrolyte fluid leaked from a battery pack to contact your
eyes, skin or clothing. If caustic electrolyte fluid should contact your eyes,
immediately wash your eyes with large amounts of running water and seek
medical attention, to help prevent eye damage. It electrolyte fluid should
contact your skin immediately wash it under running water to prevent rash. If
it contacts your clothes, promptly remove them to prevent the fluid from
contacting your skin or eyes.
2. Immediately turn off the power, disconnect the universal AC adaptor and
remove the battery if any of the following events are observed in the battery
pack: offensive or unusual odor, excessive heat, discoloration or deformation.
Never use the computer again until it has been checked by a TOSHIBA
service provider. It might generate smoke or fire, or the battery pack might
rupture.
3. Make sure the battery is securely installed in the computer before attempting
to charge the battery pack. Improper installation could generate smoke or fire,
or cause the battery pack to rupture.
4. Keep the battery pack out or reach of infants and children. It can cause injury.
6-6
Care and use of the battery pack
1. Never continue to use a battery pack after its recharging capacity has become
impaired, or after the display of a warning message indicating that the battery
pack’s power is exhausted. Continued use of an exhausted or impaired battery
pack could cause the loss of data.
2. Never dispose of battery packs with normal trash. Bring them to your
TOSHIBA dealer or to another recycling center to save resources and prevent
environmental damage. Cover the terminals with electrical tape to prevent
short-circuits, which could cause the battery pack to ignite or rupture.
3. Use only battery packs recommended by TOSHIBA as replacements.
4. Always make sure the battery pack is installed correctly and securely.
Otherwise, a battery pack could fall out and possibly cause injury.
5. Charge the battery pack only in an ambient temperature between 5 and 35
degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack
performance might deteriorate and the battery life might be shortened.
6. Be sure to monitor the remaining battery power. If the battery pack and real
time clock battery discharge completely, Standby and Suspend will not
function and data in memory will be lost. Also, the computer might register an
incorrect time and date. In this case, connect the universal AC adaptor to
recharge the batteries.
7. Never install or remove the battery pack without first turning off the power
and disconnecting the universal AC adaptor. Never remove the battery pack
while the computer is in Suspend or Standby mode. Data will be lost.
Note
1. Never remove the battery pack while the Wake-up on LAN function is
enabled. Data will be lost. Before you remove a battery pack, disable the
Wake-up on LAN function.
2. To ensure the battery pack maintains maximum capacity, operate the computer
on battery power once a week until the battery pack is fully discharged. Refer
to the section Extending battery life in this chapter for procedures. If the
computer is continuously operated on AC power for an extended period, more
than a week, the battery might fail to retain a charge. It might not function
efficiently over the expected life of the battery pack and the Battery indicator
might not indicate a low-battery condition.
3. After the battery pack is charged, avoid leaving the universal AC adaptor
connected and the computer turned off for more than a few hours at a time.
Continuing to charge a fully-charged battery pack can damage the battery.
6-7
POWER AND
POWER-UP MODES
Caution
POWER AND
POWER-UP MODES
User's Manual
Charging the batteries
When the power in the battery pack becomes low, the Battery indicator flashes
orange indicating that only a few minutes of battery power remain. If you continue
to use the computer while the Battery indicator flashes, the computer enables
Hibernation mode (so you don’t lose data) and automatically turns off.
NOTE: The computer enters Hibernate mode only if Hibernation is
enabled in two places in TOSHIBA Power Saver: the Hibernate window
and the Battery Alarm item of the Alarm window.
You must recharge a battery pack when it becomes discharged.
Procedures
To recharge a battery pack while it is installed in the computer, connect the
universal AC adaptor to the DC IN socket and plug the other end into a working
outlet.
The Battery indicator glows orange when the battery is being charged.
CAUTION: Use only the computer connected to an AC power source or
the optional TOSHIBA Battery charger to charge the battery pack. Never
attempt to charge the battery pack with any other charger.
Time
The following table shows the approximate time required to fully charge a discharged battery.
Charging time (hours)
Battery type
Power on
Power off
Battery pack
7 to 12.5 or longer
about 3.5
RTC battery
8
Doesn’t charge
NOTE: The charging time when the computer is on is affected by ambient
temperature, the temperature of the computer and how you use the
computer. If you make heavy use of external devices, for example, the
battery might scarcely charge at all during operation. Refer also to the
section Maximizing battery operating time.
6-8
Care and use of the battery pack
The battery may not charge right away under the following conditions:
❑
The battery is extremely hot or cold. If the battery is extremely hot, it might not
charge at all. To ensure the battery charges to its full capacity, charge the
battery at room temperature of 10° to 30°C (50° to 88°F).
❑
The battery is nearly completely discharged. Leave the universal AC adaptor
connected for a few minutes and the battery should begin charging.
The Battery indicator may show a rapid decrease in battery operating time when
you try to charge a battery under the following conditions:
❑
The battery has not been used for a long time.
❑
The battery has completely discharged and been left in the computer for a long
time.
❑
A cool battery is installed in a warm computer.
In such case, follow the steps below.
1. Fully discharge the battery by leaving it in the computer with the power on
until the power automatically shuts off.
2. Plug in the universal AC adaptor.
3. Charge the battery until the Battery indicator glows green.
Repeat these steps two or three times until the battery recovers normal capacity.
NOTE: Leaving the universal AC adaptor connected will shorten battery
life. At least once a month, run the computer on battery power until the
battery is fully discharged, then recharge the battery.
Monitoring battery capacity
Remaining battery power can be monitored in the Power Save Modes window in
Power Saver.
NOTES: 1. Wait at least 16 seconds after turning on the computer before
trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining
capacity and to calculate the remaining operating time,
based on the current power consumption rate and remaining
battery capacity. The actual remaining operating time may
differ slightly from the calculated time.
6-9
POWER AND
POWER-UP MODES
Battery charging notice
POWER AND
POWER-UP MODES
User's Manual
2. With repeated discharges and recharges, the battery’s
capacity will gradually decrease. Therefore, an often
used, older battery will not operate for as long as a new
battery even when both are fully charged. In this case,
Power Save Modes window in TOSHIBA Power Saver
will indicate a 100% charge for both the old and new
battery, but the displayed estimated time remaining will
be shorter for the older battery.
Maximizing battery operating time
A battery’s usefulness depends on how long it can supply power on a single
charge.
How long the charge lasts in a battery depends on:
❑
How you configure the computer (for example, whether you enable batterypower saving options). The computer provides a battery save mode, which can
be set in TOSHIBA Power Saver, to conserve battery power. This mode has
the following options:
• Processor speed
• Monitor brightness
• System standby
• System hibernate
• Turn off monitor
• Turn off hard disks
❑
How often and how long you use the hard disk, CD/DVD-ROM and the
diskette drive.
❑
How much charge the battery contained to begin with.
❑
How you use optional devices, such as a PC card, to which the battery
supplies power.
❑
Enabling Standby mode conserves battery power if you are frequently turning
the computer off and on.
❑
Where you store your programs and data.
❑
Closing the display when you are not using the keyboard saves power.
❑
Operating time decreases at low temperatures.
❑
The condition of the battery terminals. Make sure the battery terminals stay
clean by wiping them with a clean dry cloth before installing the battery pack.
6-10
Care and use of the battery pack
When you turn off your computer with fully charged batteries, the batteries retain
data for the following approximate time periods:
Battery pack
about 6 days (Standby mode)
about 30 days (Boot mode)
RTC battery
1 month
Extending battery life
To maximize the life of your battery pack:
❑
At least once a month, disconnect the computer from a power source and
operate it on battery power until the battery pack fully discharges. Before doing
so, follow the steps below.
1. Turn off the computer’s power.
2. Disconnect the universal AC adaptor and turn on the computer’s power. If it
does not turn on go to step 4.
3. Operate the computer on battery power for five minutes. If the battery pack
has at least five minutes of operating time, continue operating until the
battery pack is fully discharged. If the Battery indicator flashes or there is
some other warning to indicate a low battery, go to step 4.
4. Connect the universal AC adaptor to the computer and the power cord to a
power outlet. The DC IN indicator should glow green, and the Battery
indicator should glow orange to indicate that the battery pack is being
charged. If the DC IN indicator does not glow, power is not being supplied.
Check the connections for the universal AC adaptor and power cord.
5. Charge the battery pack until the Battery indicator glows green.
❑
If you have extra battery packs, rotate their use.
❑
If you will not be using the system for an extended period, more than one
month, remove the battery pack.
❑
Disconnect the universal AC adaptor when the battery is fully charged.
Overcharging makes the battery hot and shortens life.
❑
If you are not going to use the computer for more than eight hours, disconnect
the universal AC adaptor.
❑
Store spare battery packs in a cool dry place out of direct sunlight.
6-11
POWER AND
POWER-UP MODES
Retaining data with power off
POWER AND
POWER-UP MODES
User's Manual
Replacing the battery pack
When the battery pack reaches the end of its operating life you will need to install a
new one. The life of the battery pack is generally about 500 recharges. If the
Battery indicator flashes orange shortly after fully recharging the battery, the
battery pack needs to be replaced.
You might also replace a discharged battery pack with a charged spare when you
are operating your computer away from an AC power source. This section explains
how to remove and install the battery pack.
Removing the battery pack
To replace a discharged battery, follow the steps below.
CAUTIONS: 1. When handling battery packs, be careful not to short
circuit the terminals. Also do not drop, hit or otherwise apply impact; do not scratch or break the casing
and do not twist or bend the battery pack.
2. Do not remove the battery pack while the computer is
in Standby mode. Data is stored in RAM, so if the
computer loses power it will be lost.
3. In Hibernation mode, data will be lost if you remove
the battery or disconnect the universal AC adaptor
before the save is completed. Wait for the Disk
indicator to go out.
4. Do not touch the latch while holding the computer. Or
you may get injured by the drpped battery by
unintentional release of the latch.
1. Save your work.
2. Turn the computer’s power off. Make sure the Power indicator is off.
3. Remove all cables connected to the computer.
4. Turn the computer upside down.
5. Slide the battery release latch to free the battery pack for removal, then slide
out the battery pack.
6-12
Replacing the battery pack
POWER AND
POWER-UP MODES
BATTERY
BATTERY PACK
RELEASE LATCH
Figure 6-1 Releasing the battery cover
CAUTION: For environmental reasons, do not throw away a spent
battery pack. Please return spent battery packs to your TOSHIBA dealer.
Installing the battery pack
To install a battery, follow the steps below.
CAUTIONS: 1. The battery pack is a lithium ion battery, which can
explode if not properly replaced, used, handled or
disposed of. Dispose of the battery as required by local
ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements.
2. Do not touch the latch while holding the computer. Or
you may get injured by the drpped battery by
unintentional release of the latch.
1. Turn the computer’s power off.
2. Disconnect all cables connected to the computer.
3. Insert the battery pack.
4. Secure the battery pack lock.
6-13
POWER AND
POWER-UP MODES
User's Manual
BATTERY
RELEASE LATCH
BATTERY PACK
Figure 6-2 Securing the battery cover
Starting the computer by password
To start up the computer with the user password, follow these steps:
1. Turn on the power as described in Chapter 3, Getting Started. The following
message appears:
Password =
NOTE: At this point, the hot keys Fn + F1 to F5 do not work. They will
function after you enter the password.
2. Enter the password.
3. Press Enter.
NOTE: If you enter the password incorrectly three times in a row, the
computer shuts off. In this case, you must turn the computer back on to
retry password entry.
6-14
Power-up modes
The computer has the following power-up modes:
❑
Boot: Computer shuts down without saving data. Always save your work
before you turn the computer off in boot mode.
❑
Hibernation: Data in memory is saved to the hard disk.
❑
Standby: Data is maintained in the computer’s main memory.
NOTE: Refer also to the sections Turning on the power and Turning off
the power in Chapter 3, Getting Started.
Windows utilities
You can specify the setting in TOSHIBA Power Saver.
Hot keys
You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter
Hibernation. See Chapter 5, Keyboard for details.
Panel power off
You can set up your computer so that power turns off automatically when you close
the display panel. When you open the panel, power turns on in Standby or
Hibernation mode but not in boot mode.
NOTE: If the panel power off function is enabled and you use Shut down
Windows, do not close the display until the shut down function is
completed.
System Auto Off
This feature turns the system off automatically if it is not used for a set duration.
The system shuts down in Standby mode or Hibernation mode in Windows.
6-15
POWER AND
POWER-UP MODES
Power-up modes
POWER AND
POWER-UP MODES
User's Manual
6-16
Chapter 7
HW Setup and Passwords
HW Setup
TOSHIBA HW Setup lets you configure settings for Display, Boot Priority,
Keyboard, USB, LAN, General, Password, Device Config and Parallel/Printer.
NOTE: If the supervisor password is set, access to the TOSHIBA HW Setup
program can be prevented when the user password is used to log on to the
computer.
Accessing HW Setup
To run HW Setup, click start, click Control Panel and select TOSHIBA HW
Setup.
HW Setup window
The HW Setup window contains the following tabs: Display, Boot Priority,
Keyboard, USB, LAN, General, Password, Device Config and Parallel/Printer.
There are also three buttons: OK, Cancel and Apply.
OK
Cancel
Apply
Accepts your changes and closes the HW Setup window.
Closes the window without accepting your changes.
Accepts all your changes without closing the HW Setup
window.
7-1
HW SETUP AND
PASSWORDS
This chapter explains how to use TOSHIBA HW Setup program to configure your
computer and how to set passwords.
User's Manual
Display
This tab lets you customize your computer’s display settings for either the internal
LCD screen or for an external monitor.
Power On Display
HW SETUP AND
PASSWORDS
Lets you set the display to be used when the computer is booted.
Auto-Selected
Selects an external monitor if one is connected. Otherwise, it selects the internal LCD. (Default)
LCD + AnalogRGB
Selects both the internal LCD and external monitor for
simultaneous display.
Boot Priority
Boot Priority Options
This option sets the priority for booting the computer. Select from the following
settings:
HDD −> FDD −> CD-ROM −> LAN The computer looks for bootable files in
the following order: HDD, diskette drive,
CD-ROM* and LAN. (Default)
FDD −> HDD −> CD-ROM −> LAN The computer looks for bootable files in
the following order: diskette drive, HDD,
CD-ROM* and LAN.
HDD −> CD-ROM −> LAN −> FDD The computer looks for bootable files in
the following order: HDD, CD-ROM*, LAN
and diskette drive.
FDD −> CD-ROM −> LAN −> HDD The computer looks for bootable files in
the following order: diskette drive, CDROM*, LAN and HDD.
CD-ROM −> LAN −> HDD −> FDD The computer looks for bootable files in
the following order: CD-ROM*, LAN,
HDD, diskette drive.
CD-ROM −> LAN −> FDD −> HDD The computer looks for bootable files in
the following order: CD-ROM*, LAN,
diskette drive and HDD.
*
In this computer, CD-ROM refers to the Slim Select Bay optical media drive.
To change the boot drive, follow the steps below.
7-2
HW Setup
1. Hold down F12 and boot the computer.
2. The following menu will be displayed with the following icons: Built-in HDD,
Slim Select Bay HDD, CD-ROM, FDD, Network (LAN), PCA (ATA) card boot.
3. Use the left/right cursor keys to highlight the boot device you want and press
Enter.
NOTES: 1. If a supervisor password is set, the menu above does not
appear when you use the user password to start the
computer.
2. The selection method above does not change the boot
priority settings in HW Setup.
3. If you press a key other than one of those above or if the
selected device is not installed, the system will boot according
to the current setting in HW Setup.
4. Support of PCA (ATA) card boot is guaranteed only for
TOSHIBA PC card HDDs.
5. A PCA (ATA) card takes the position of HDD in the Boot
Priority Options list.
HDD Priority Options
If more than one HDD is installed in the computer, this option lets you set the
priority for HDD detection. If the first detected HDD has a boot command, the
system will boot from the HDD.
Built-in HDD −> 2nd HDD −> PC Card (Default)
HDDs are searched for a boot command in the following
order: the built-in HDD, the HDD installed in the Slim
Select Bay and the PC card. (Default)
2nd HDD −> Built-in HDD −> PC Card
HDDs are searched for a boot command in the following
order: the HDD installed in the Slim Select Bay, the built-in
HDD and the PC card.
7-3
HW SETUP AND
PASSWORDS
NOTE: A bar will appear only under the selected device.
User's Manual
Built-in HDD −> PC Card −> 2nd HDD
HDDs are searched for a boot command in the following
order: the built-in HDD, the PC card and the HDD installed
in the Slim Select Bay.
HW SETUP AND
PASSWORDS
2nd HDD −> PC Card −> Built-in HDD
HDDs are searched for a boot command in the following
order: the HDD installed in the Slim Select Bay, the PC card
and the built-in HDD.
PC Card −> Built-in HDD −> 2nd HDD
HDDs are searched for a boot command in the following
order: the PC card, the built-in HDD and the HDD installed
in the Slim Select Bay.
PC Card −> 2nd HDD −> Built-in HDD
HDDs are searched for a boot command in the following
order: the PC card, the HDD installed in the Slim Select Bay
and the built-in HDD.
NOTE: If a boot command is not found on the first detected HDD, the
system will not boot from the other HDD. It will search the next device in
the boot priority for a boot command.
Network Boot Protocol
This feature sets the protocol to remotely boot from the network.
[PXE]
[RPL]
Sets PXE as the protocol. (Default)
Sets RPL as the protocol.
Keyboard
Wake-up on Keyboard
When this feature is enabled and the computer is in Standby mode, you can turn on
the computer by pressing any key. It is effective only for the internal keyboard and
only when the computer is in standby mode.
Enabled
Disabled
7-4
Enables the Wake-up on Keyboard.
Disables the Wake-up on Keyboard. (Default)
HW Setup
USB
USB KB/Mouse Legacy Emulation
Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your
operating system does not support USB, you can still use a USB mouse and
keyboard by setting the USB KB/Mouse Legacy Emulation item to
Enabled.
Enables the USB KB/Mouse Legacy Emulation. (Default)
Disables the USB KB/Mouse Legacy Emulation.
USB-FDD Legacy Emulation
Use this option to enable or disable USB-FDD Legacy Emulation.
Enabled
Disabled
Enables the USB-FDD Legacy Emulation. (Default)
Disables the USB-FDD Legacy Emulation.
LAN
Wake-up on LAN
This features lets the computer’s power be turned on when it receives a wake-up
signal from the LAN.
Enabled
Disabled
Enables Wake-up on LAN.
Disables Wake-up on LAN. (Default)
CAUTION: Do not install or remove an optional memory module while
Wake-up on LAN is enabled.
NOTE: The Wake-up on LAN function consumes power even when the
system is off. Leave the universal AC adaptor connected while using this
feature.
Built-in LAN
This feature enables or disables the Built-in LAN.
Enabled
Disabled
Enables Built-in LAN functions. (Default)
Disables Built-in LAN functions.
7-5
HW SETUP AND
PASSWORDS
Enabled
Disabled
User's Manual
General
This window displays the BIOS version and contains two buttons: Default and
About.
Setup
HW SETUP AND
PASSWORDS
This field displays BIOS Version and date.
Default
Click Default to return all HW Setup values to the factory settings.
About
Click About to display the HW Setup version.
Password
User Password
This option allows you to set or reset the user password for power on.
Not Registered
Registered
Change or remove the password. (Default)
Set the password. A dialogue box will appear to let you set
the password.
To enter a user password:
1. Select Registered to display the following prompt:
Enter Password:
2. Enter a password of up to 10 characters. (You cannot use the following
characters: - ^ @ [ ] ; : , . / space.) The character string you enter is
displayed as a string of asterisks. For example, if you enter a password
consisting of four characters, the display is shown as:
Enter Password: ****
NOTE: If you click the OK button before entering the password, Not
registered will appear on the display.
3. Click the OK button. The following message appears, allowing you to verify
the password.
Verify Password:
7-6
HW Setup
4. If character strings match, the password is registered and the display changes
to:
The password was registered
If they do not match, the following message appears. You must repeat from
step 1.
Entry Error!!!
HW SETUP AND
PASSWORDS
To delete a user password:
1. Select Not Registered to display the following prompt:
Enter Password:
2. Enter the currently registered password. The character string you enter is
displayed as a string of asterisks.
Enter Password: ****
NOTE: If you click the OK button before entering the password, Registered will appear on the display.
3. Click the OK button. If the character string you enter matches the registered
password, the password option is reset and the display changes to:
The password was deleted
If they do not match, the following message appears. You must repeat step 1.
Incorrect Password
NOTE: If you enter the password incorrectly three times, the screen will
display:
Sorry, access denied!!! Powering off your
machine then powering it back on again are
required to regain access.
You will not be able to access the password option in the HW Setup. In
this case you must turn the power off and back on to retry the procedure.
4. Follow the same procedures described in the earlier section, How to set the
password, to set a new user password.
Refer to the Supervisor password section later in this chapter for details on setting
the supervisor password.
7-7
User's Manual
Key FD
After you set a password, you can create a Key FD (diskette). If you forget the user
password, the Key FD lets you bypass the password function.
HW SETUP AND
PASSWORDS
NOTE: It is a good idea to create more than one Key FD in case a Key
FD is damaged or lost.
To create a Key FD follow the steps below.
1. Turn off the computer’s power.
2. Connect the diskette drive to a USB port on the computer.
3. Set a diskette’s write-protect tab to the write enable position and insert the
diskette in the drive.
NOTE: All data on the diskette will be destroyed.
4. Turn on the computer’s power.
Password= will be displayed on the LCD.
5. Enter the password.
6. Press the Tab key.
Insert FD Ready (Y/N) will be displayed on the LCD.
7. Press Y.
Remove FD press key will be displayed on the LCD.
8. Remove the diskette and press any key.Supervisor password
Refer to the readme file of the Supervisor Password Utility for instructions on
setting the Supervisor Password.
The path to the readme file is C:\Program Files\TOSHIBA\Windows
Utilities\SVPWTool. In the SVPWTool directory, open the readme.htm
file.
Device Config
Device Configuration
This option lets you set the device configuration.
7-8
All Devices
BIOS sets all devices.
Setup by OS
Operating system sets devices that it can control. (Default)
Supervisor password
Parallel/Printer
This tab lets you set the Parallel Port Mode. Use the Windows Device Manager to
make settings for the Parallel port.
Parallel Port Mode
The options in this tab are ECP and Standard Bi-directional.
Standard
Bi-directional
Sets the port type to Extended Capabilities Port (ECP). For
most printers, the port should be set to ECP. (Default)
This setting should be used with some other parallel
devices.
Supervisor password
Refer to the readme file of the Supervisor Password Utility for instructions on
setting the Supervisor Password.
The path to the readme file is C:\Program Files\TOSHIBA\Windows
Utilities\SVPWTool. In the SVPWTool directory, open the readme.htm
file.
7-9
HW SETUP AND
PASSWORDS
ECP
HW SETUP AND
PASSWORDS
User's Manual
7-10
Chapter 8
Optional Devices
Optional devices can expand the computer’s capabilities and its versatility. This
chapter describes connection or installation of the following devices, which are
available from your TOSHIBA dealer:
Cards/memory
PC cards
❑
SD cards
❑
Memory expansion
❑
TOSHIBA Style Bay Bridge media adaptor (Memory Stick/Smart Media/
Compact Flash memory)
OPTIONAL DEVICES
❑
Power devices
❑
Battery pack
❑
Universal AC adaptor
Peripheral devices
❑
USB FDD kit
❑
Slim Select Bay HDD adaptor
❑
External monitor
❑
TV
❑
i.LINK(IEEE1394)
Other
❑
Security lock
8-1
User's Manual
PC cards
The computer is equipped with a PC card expansion slot that can accommodate two
5 mm Type II cards. Any PC card that meets industry standards (manufactured by
TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards,
including PC card 16’s multifunction card and CardBus PC cards.
CardBus supports the new standard of 32-bit PC cards. The bus provides superior
performance for the greater demands of multimedia data transmission.
Inserting a PC card
OPTIONAL DEVICES
The PC card connector is located on the left side of the computer.
Windows’ hot-install feature lets you install PC cards while the computer’s power is
on.
NOTE: Do not install a PC card while the computer is in standby or
hibernation mode. Some cards might not work properly.
To install a PC card, follow the steps below.
1. Insert the PC card.
2. Press gently to ensure a firm connection.
PC CARD
Figure 8-1 Installing the PC card
After installing the card, refer to the card’s documentation and check the configuration in Windows to make sure it is appropriate for your card.
8-2
PC cards
Removing a PC card
To remove the PC card, follow the steps below.
1. Click the Safety Remove Hardware icon on the Task Bar.
2. Click PC card.
3. Press the PC card eject button to extend it.
4. Press the extended eject button to pop the card out slightly.
5. Pinch the PC card and remove it.
OPTIONAL DEVICES
PC CARD
EJECT BUTTON
Figure 8-2 Removing the PC card
8-3
User's Manual
SD cards
The computer is equipped with an SD card slot that can accommodate Secure
Digital flash memory cards with various memory capacities. SD cards let you easily
transfer data from devices, such as digital cameras and Personal Digital Assistants,
that use SD card flash-memory. The cards have a high level of security and copy
protection features. The slot cannot accommodate MultiMedia cards.
OPTIONAL DEVICES
CAUTION: Keep foreign objects out of the SD card slot. A pin or similar
object can damage the computer’s circuitry.
NOTE: SD memory cards comply with SDMI (Secure Digital Music
Initiative), which is a technology adopted to prevent unlawful copy or
playback of digital music. For this reason, you cannot copy or playback
protected material on another computer or other device. You may not use
the reproduction of any copyrighted material except for your personal
enjoyment.
Inserting an SD card
To insert an SD card, follow the steps below.
1. Insert the SD card.
2. Press it gently to ensure a firm connection.
SD CARD
Figure 8-3 Inserting an SD card
CAUTION: Make sure the SD card is oriented properly before you insert
it.
8-4
SD cards
Removing an SD card
To remove an SD card, follow the steps below.
1. Click the Safety Remove Hardware icon on the Task Bar.
2. Point to SD card and click.
3. Push in the card and release it to pop the card out slightly.
4. Grasp the card and remove it.
OPTIONAL DEVICES
SD CARD
INDICATOR
SD CARD
Figure 8-4 Removing an SD card
CAUTION: Make sure the SD card indicator is out before you remove
the card or turn off the computer’s power. If you remove the card or turn
off the power while the computer is accessing the card you may lose data
or damage the card.
SD card care
CAUTION: Set the write-protect switch to the lock position, if you do not
want to record data.
1. Do not write to an SD card if the battery power is low. Low power could affect
writing accuracy.
2. Do not remove an SD card while read/write is in progress.
3. The SD card is designed so that it can be installed only one way. Do not try to
force the card into the slot.
4. Do not leave an SD card partially inserted in the slot. Press the SD card until
you hear it click into place.
8-5
User's Manual
5. Do not twist or bend SD cards.
6. Do not expose SD cards to liquids or store in humid areas or in lay media close
to containers of liquid.
7. After using an SD card, return it to its case.
8. Do not touch the metal part or expose it to liquids or let it get dirty.
Memory expansion
This computer is equipped with two memory module sockets beneath the keyboard.
You can increase the amount of RAM by installing an additional memory or
replacing default memories with additional memories. This section describes how to
install and remove a memory module.
OPTIONAL DEVICES
NOTE: Place a mat beneath the computer to prevent making a scratch
on the lid when replacing the memory module. Avoid the mat that
generates static electricity.
CAUTION: Use only memory modules approved by TOSHIBA.
CAUTION: Do not try to install or remove a memory module under the
following conditions. You can damage the computer and the module.
Also, data will be lost.
1.
The computer is turned on.
2.
The computer was shut down using the Stand by mode or Hibernation mode.
3.
Wake-up on LAN is enabled.
NOTE: Use a 1-bit, Phillips screwdriver to remove and fasten screws. Use
oa an incorrect screwdriver can damage the screw heads.
Installing memory module
Follow the steps below to install a memory module.
1. Set the computer to boot mode and turn the computer’s power off. Make sure
the Power indicator is off.
2. Remove universal AC adaptor and all cables connected to the computer.
3. Turn the computer upside down and remove the battery pack. Refer to
Removing the Battery Pack in chapter 6; Power and Power-up Modes for the
detail.
8-6
Memory expansion
4. Turn the computer to the normal position and open the display panel. Tilt the
display panel slightly beyond the upright position before removing the
keyboard display.
5. Put your fingers on the both ends of the keyboard brace and remove it
carefully to the direction indicated with arrows.
KEYBORD BRACE
6. Remove three screws (right and left at the both right and left end and in the
upper middle of the keyboard) fixing the keyboard.
Figure 8-6 Removing the keyboard (1)
CAUTION: Be careful not to drop the screw inside the computer when
removing.
8-7
OPTIONAL DEVICES
Figure 8-5 Removing the keyboard brace
User's Manual
OPTIONAL DEVICES
7. Press the keyboard to the other side. Turn the keyboard upside down when a
flat cable appears.
Figure 8-7 Removing the keyboard (2)
Figure 8-8 Removing the keyboard (3)
8-8
Memory expansion
8. Raise the insulation sheet covering the memory module to appear the module.
OPTIONAL DEVICES
INSULATION SHEET
Figure 8-9 Raising the insulation sheet
CAUTION: Do not touch VGA chip, or you will get burnt.
9. Keep the insulation sheet raised using adhesive tape.
Figure 8-10 Raising the insulation sheet
8-9
User's Manual
OPTIONAL DEVICES
10. Insert a new module to the socket and push it downward to lie flat. Latches on
either side will click into place to secure the module.
Figure 8-11 Installing a memory module
Figure 8-12 Installing two memory modules
11. Seat the insulation sheet to cover the module.
NOTE: Be sure to check that the insulation sheet is returned to the
original position to cover the memory module.
8-10
Memory expansion
12. Insert the tabs of the keyboard into the slits of the computer case and seat the
keyboard at the original position. Fix it with three screws removed in 6.
CAUTIONS: 1. Be sure to use all screws that were removed in 6 and
do not leave foreign matters such as adhesive tape
used in 9 or screws removed and dropped in the
computer.
2. When seating the keyboard at the original position, be
sure to return the flexible printed circuit board under
the metal sheet if the flexible printed circuit board was
dragged out while removing the keyboard.
13. Seat the keyboard brace in the original position.
OPTIONAL DEVICES
14. Install the battery pack as described in Chapter 6, Power and Power-up
Modes.
15. Turn the power on and make sure the added memory is recognized. Open
System Properties in the Control Panel and click the General tab.
Removing memory module
To remove the memory module, make sure the computer is in boot mode then:
1. Be sure the power is off and all cables are disconnected from the computer.
2. Turn the computer upside down and remove the battery.
3. Follow the instructions 4 through 9 in “Installing memory module” to appear
memory module.
4. Push the latches to the outside to release the module. A spring will force one
end of the module up.
5. Pinch the module by the sides and pull it out.
CAUTIONS: 1. If you use the computer for a long time, the memory
modules and the circuits locating close to the memory
modules will become hot. In this case, let them cool to
room temperature before you replace them. Or you will
get burnt if you touch any of them.
2. Do not touch the connectors on the memory module or
on the computer. Debris on the connectors may cause
memory access problems.
8-11
OPTIONAL DEVICES
User's Manual
Figure 8-13 Removing the memory module
6. Follow the instructions 11 through 15 in “Installing memory module”.
TOSHIBA Style Bay Bridge media
adaptor
You can insert three types of flash memory cards — CompactFlash, Memory Stick
and SmartMedia — in the computer’s TOSHIBA Style Bay Bridge media adaptor.
For details on using the adaptor, follow the steps below. For details on inserting
modules in the Slim Select Bay, refer to Chapter 4, Operating Basics.
8-12
TOSHIBA Style Bay Bridge media adaptor
Before installing
Make sure you have the correct Bridge media adaptor case. Two cases come with
the Bridge media adaptor: one marked A and one marked B. The case for the
Satellite Pro M10 is marked with a B.
NOTE: Case B is also used with the Satellite 2450 computer. Case A is
used with the Satellite 5200 series.
B
OPTIONAL DEVICES
Figure 8-14 The Bridge media adaptor case
Inserting
To install the Bridge media adaptor in the case, follow the steps below.
1. Fit the side of the Bridge media adaptor opposite the connector into the case.
2. Lay the Bridge media adaptor into the case. The latch should close
automatically to secure the adaptor.
Figure 8-15 Installing the Bridge media adaptor in the case
8-13
User's Manual
OPTIONAL DEVICES
3. Turn the Bridge media adaptor with case upside down and secure the case to
the adaptor with one screw.
Figure 8-16 Secureing a screw
Removing
To remove the Bridge media adaptor from the case, follow the steps below.
1. Turn the Bridge media adaptor with case upside down and remove one screw.
2. Slide the latch in the direction of the arrow shown below.
3. Push the Bridge media adaptor up from the bottom and lift it out.
Figure 8-17 Removing the Bridge media adaptor from the case
8-14
TOSHIBA Style Bay Bridge media adaptor
SmartMedia
This slot accommodates 3.3 V SmartMedia (RAM) from 2 MB to 128 MB.
❑
You cannot use SmartMedia that does not conform to SSFDC specifications.
❑
Operation of SmartMedia developed after the computer was manufactured is
not guaranteed.
❑
After you finish using SmartMedia, return it to its case, which is resistant to
static electricity.
Write protection
SmartMedia can be write protected to safeguard your data.
To write-protect SmartMedia, apply a seal to the write-protect area. To write-enable,
remove the seal.
Do not use the standard Windows format, because your camera or other
device might not be able to read it. Formatting destroys all data on the card, so
be sure it contains no data you want to keep.
❑
Do not reuse a write-protect seal that has been removed. A reused seal might
peel off in the computer or device and cause a malfunction.
Inserting
1. To insert SmartMedia, turn the card so that the connector (metal area) faces
up.
2. Push the card into the slot until it locks into place.
NOTE: If Windows does not recognize a SmartMedia card, try removing
the card and inserting it again. Be careful not to touch the connectors.
You could expose the storage area to static electricity, which can destroy
data.
8-15
OPTIONAL DEVICES
❑
User's Manual
SMARTMEDIA
OPTIONAL DEVICES
SMARTMEDIA INDICATOR
Figure 8-18 Inserting a SmartMedia
Removing
CAUTION: Do not remove a SmartMedia card while data is being
written or read. Data could be destroyed. Wait for SmartMedia
indicator on the left side of the SmartMedia slot to go out.
1. Right click (right button of the Touch Pad) on the SmartMedia drive’s icon
and select Eject from the pop-up menu.
2. Push the card and release it. The card will pop out slightly.
3. Lift the left side of the computer slightly and grasp the card. Pull it straight out.
SMARTMEDIA
Figure 8-19 Removing a SmartMedia
8-16
TOSHIBA Style Bay Bridge media adaptor
Memory Stick
This slot accommodates Memory Stick from 16MB to 128MB.
NOTE: The slot does not support Magic Gate functions.
Write protection
Memory Stick can be write protected to safeguard your data. To write-protect a
Memory Stick, slide the lock on the back of the Memory Stick to the lock position.
Installing a Memory Stick
To install a Memory Stick, follow the steps below.
1. Insert the Memory Stick into the slot.
OPTIONAL DEVICES
2. Press gently to ensure a firm connection.
MEMORY STICK
INDICATOR
MEMORY STICK
Figure 8-20 Inserting a Memory Stick
Removing a Memory Stick
To remove a Memory Stick, follow the steps below.
1. Right-click (right button of the Touch Pad) on the Memory Stick driver’s icon
and select Eject from the pop-up menu.
2. Push in the Memory Stick and release it to pop the Memory Stick out slightly.
3. Grasp the Memory Stick and pull it out.
8-17
User's Manual
CAUTION: Make sure the Memory Stick indicator is out before you
remove the Memory Stick or turn off the computer’s power. If you remove
the Memory Stick or turn off the power while the computer is accessing
the Memory Stick, you may lose data or damage the Memory Stick.
Compact Flash
This slot accommodates Compact Flash from 16MB to 512MB. You cannot use
Compact Flash that does not conform to CFA specifications.
Installing a Compact Flash module
To install a Compact Flash module, follow the steps below.
OPTIONAL DEVICES
1. Insert the Compact Flash into the slot.
2. Press gently to ensure a firm connection.
EJECT BUTTON
COMPACT FLASH
COMPACT FLASH INDICATOR
Figure 8-21 Inserting a Compact Flash module
Removing a Compact Flash memory module
To remove a Compact Flash, follow the steps below.
1. Right click (right button of the Touch Pad) on the Compact Flash drive’s icon
and select Eject from the pop-up menu.
2. Press the Compact Flash eject button to extend it.
3. Press the extended eject button to pop the Compact Flash out slightly.
4. Grasp and pull out the Compact Flash.
8-18
Slim Select Bay HDD adaptor (Black)
CAUTION: Make sure the Compact Flash indicator is out before you
remove the Compact Flash or turn off the computer’s power. If you
remove the Compact Flash or turn off the power while the computer is
accessing the Compact Flash you may lose data or damage the Compact
Flash.
Bridge media care
1. Bridge media is consumable item, so make sure you back up important data.
2. Do not twist or bend Bridge media.
3. Do not expose Bridge media to liquids or store in humid areas or lay media
close to containers of liquid.
4. Do not touch the metal part or expose it to liquids or let it get dirty.
OPTIONAL DEVICES
5. After using Bridge media, return it to its case.
NOTE: For more details on using the Bridge media, see manuals
accompaning the Bridge media.
Battery pack (Black)
You can increase the portability of the computer with additional battery packs. If
you’re away from an AC power source and your battery runs low, you can replace it
with a freshly charged battery. See Chapter 6, Power and Power-Up Modes.
Universal AC adaptor
If you frequently transport the computer between different sites such as your home
and office, purchasing a universal AC adaptor for each location will reduce the
weight and bulk of your carrying load.
USB FDD kit
The 3 1/2" external diskette drive module can be connected to the USB port. For
details on connecting the 3 1/2" external diskette drive module, refer to Chapter 4,
Operating Basics.
8-19
User's Manual
Slim Select Bay HDD adaptor (Black)
A integrated 2 1/2" HDD is available for installation in the Slim Select Bay.
To install an HDD in the Slim Select Bay HDD adaptor follow the steps below.
OPTIONAL DEVICES
1. Slide the lock to the unlock position and open the lid.
Figure 8-22 Opening the lid
2. Insert the HDD and push forward to ensure a firm connection.
Figure 8-23 Installing the HDD
8-20
TV
3. Close the lid and slide the lock to the lock position.
For details on installing the Slim Select Bay HDD adaptor in the Slim Select Bay,
refer to Chapter 4, Operating Basics.
External monitor
An external analog monitor can be connected to the external monitor port on the
computer. The computer supports VGA and Super VGA video modes. To connect a
monitor, follow the steps below.
1. Turn the computer off.
2. Connect the monitor to the external monitor port.
3. Turn the monitor’s power on.
4. Turn the computer on.
When you turn on the power, the computer automatically recognizes the monitor
and determines whether it is color or monochrome.
To change the display settings, press Fn + F5. If you disconnect the monitor
before you turn the computer off, be sure to press Fn + F5 to switch to the internal
display. Refer to Chapter 5, The Keyboard, for details on using hot keys to change
the display setting.
8-21
OPTIONAL DEVICES
Figure 8-24 Closing the lid
User's Manual
TV
You can connect a television set to the TV out jack on the computer. Follow the
steps below.
Using the TV button
1. Connect the TV adaptor cable’s S-Video plug to the TV out jack on the
computer.
2. Connect the TV adaptor cable’s MINI DIN 4Pin connector S-Video format on
the TV.
OPTIONAL DEVICES
3. Press the TV button.
You can use the hot keys Fn + F5 to change the display device. Refer to Chapter 5,
The Keyboard.
NOTE: If a television is connected to the computer, set the TV type in
Display Properties. Follow the steps below.
a. Click start and click Control Panel.
b. Double-click the Display icon to open the Display Properties
window.
c. Click the Settings tab and click the Advanced button.
d. Click the nView Display Mode tab, click Device Settings and
click Select Output Device.
e. Select Advanced and select TV in the Device Selection
window.
f. Select the Format box and select the format that your TV supports.
Changing the resolution
When you press the TV button, the CRT resolution is also set. (The default is 1024
x 768.) If you want to change the resolution, follow the steps below.
8-22
(1)
Open Display properties and select the Settings tab.
(2)
Select Advanced (Figure 8-17).
i.LINK (IEEE1394)
OPTIONAL DEVICES
Figure 8-25 Display properties
(3)
Select the Adapter tab, then select List all modes.
Figure 8-26 The Adapter window
(4) Select a resolution from the menu.
8-23
User's Manual
OPTIONAL DEVICES
Figure 8-27 Resolution menu
i.LINK (IEEE1394)
i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible
devices such as
❑
Digital video cameras
❑
Hard disk drives
❑
MO drives
❑
CD-RW drives
NOTE: i.LINK uses a four-pin connector, which does not carry
electric current. External devices will need their own power supply.
Precautions
❑
Make a back-up of your data before transferring it to the computer. There is a
possibility that the original data will be damaged. There is a particular risk that
some frames will be deleted in the case of digital video transfer. TOSHIBA
assumes no liability for such loss of data.
❑
Do not transfer data in areas where static electricity is easily generated or in
areas subjected to electronic noise. Data can be destroyed.
8-24
Security lock
❑
If you are transferring data through an IEEE1394 hub, do not connect or
disconnect other devices from the hub during data transfer. There is a likelihood that data will be damaged. Connect all devices to the hub before you turn
on the computer’s power.
❑
You may not use any copyrighted video or music data copied from a video
camera except for your personal enjoyment.
❑
If you connect/disconnect an iLINK device to/from another iLINK device that
is currently exchanging data with the computer, data frames might be dropped.
❑
Make sure data transfer has ended or turn off the computer, before you:
• Connect/disconnect an iLINK device to/from the computer.
• Connect/disconnect an iLINK device to/from another iLINK device that is
connected to the computer.
1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394)
cable into the computer.
2. Plug the other end of the cable into the device.
Note the following when you use i.LINK:
❑
You may need to install drivers for your i.LINK devices.
❑
Not all i.LINK devices have been tested. Therefore, compatibility with all i.LINK
devices cannot be guaranteed.
❑
Use S100, S200 or S400 cables no longer than three meters.
❑
Some devices might not support standby or automatic off functions.
❑
Do not connect or disconnect an i.LINK device while it is using an application
or when the computer is automatically shutting it down to save power. Data
might be destroyed.
Disconnecting
1. Click the Safety Remove Hardware icon on the Task Bar.
2. Point to i.LINK (IEEE1394) device and click.
3. Disconnect the cable from the computer then from the i.LINK device.
NOTE: Refer also to the documentation that came with your i.LINK device.
8-25
OPTIONAL DEVICES
Connecting
User's Manual
Security lock
A security lock enables you to anchor your computer to a desk or other heavy
object to help prevent unauthorized removal of the computer.
OPTIONAL DEVICES
Attach one end of a cable to the desk and the other end to the security lock slot on
the right side of the computer.
Figure 8-28 Security lock
8-26
Chapter 9
Troubleshooting
TOSHIBA designed the computer for durability. However, should problems occur,
following the procedures in this chapter can help to determine the cause.
All readers should become familiar with this chapter. Knowing what might go wrong
can help prevent problems from occurring.
Problem solving process
Resolving problems will be much easier if you observe the following guidelines:
❑
Stop immediately when you recognize a problem exists. Further action may
result in data loss or damage. You may destroy valuable problem-related
information that can help solve the problem.
❑
Observe what is happening. Write down what the system is doing and what
actions you performed immediately before the problem occurred. If you have a
printer attached, print a copy of the screen using PrtSc.
Preliminary checklist
Consider the simplest solution first. The items in this checklist are easy to fix and yet
can cause what appears to be a serious problem.
❑
Make sure you turn on all peripheral devices before you turn on the computer.
This includes your printer and any other external device you are using.
❑
Before you attach an external device, turn the computer off. When you turn the
computer back on it recognizes the new device.
❑
Make sure all options are set properly in the setup program.
❑
Check all cables. Are they correctly and firmly attached? Loose cables can
cause signal errors.
❑
Inspect all connecting cables for loose wires and all connectors for loose pins.
9-1
TROUBLESHOOTING
The questions and procedures offered in this chapter are meant as a guide, they are
not definitive problem solving techniques. Many problems can be solved simply,
but a few may require help from your dealer. If you find you need to consult your
dealer or others, be prepared to describe the problem in as much detail as possible.
User's Manual
❑
Check that your diskette or CD/DVD-ROM is correctly inserted and that the
diskette’s write protect tab is correctly set.
Make notes of your observations and keep them in a permanent error log. This will
help you describe your problems to your dealer. If a problem recurs, the log will help
you identify the problem faster.
Analyzing the problem
TROUBLESHOOTING
Sometimes the system gives clues that can help you identify why it is malfunctioning. Keep the following questions in mind:
❑
Which part of the system is not operating properly: keyboard, diskette drives,
hard disk drive, optical media drive, display. Each device produces different
symptoms.
❑
Is the operating system configuration set properly? Check the configuration
options.
❑
What appears on the display screen? Does it display any messages or random
characters? Print a copy of the screen if you have a printer attached. Look up
the messages in the software and operating system documentation. Check that
all connecting cables are correctly and firmly attached. Loose cables can cause
erroneous or intermittent signals.
❑
Do any indicators light? Which ones? What color are they? Do they stay on or
blink? Write down what you see.
❑
Do you hear any beeps? How many? Are they long or short? Are they high
pitched or low? Is the computer making any unusual noises? Write down what
you hear.
Record your observations so you can describe them to your dealer.
Software
The problems may be caused by your software or disk. If
you cannot load a software package, the media may be
damaged or the program might be corrupted. Try loading
another copy of the software.
If an error message appears while you are using a software
package, check the software documentation. These
documents usually include a problem solving section or a
summary of error messages.
Next, check any error messages in the OS documentation.
9-2
Hardware and system checklist
Hardware
If you cannot find a software problem, check your hardware. First run through the items in the preliminary
checklist above. If you still cannot correct the problem, try
to identify the source. The next section provides checklists
for individual components and peripherals.
Hardware and system checklist
This section discusses problems caused by your computer’s hardware or attached
peripherals. Basic problems may occur in the following areas:
❑ PC card
❑ Self test
❑ Infrared port
❑ Power
❑ Pointing device
❑ Password
❑ USB
❑ Keyboard
❑ Memory expansion
❑ LCD panel
❑ Sound system
❑ Hard disk drive
❑ Monitor
❑ CD-RW/DVD-ROM drive
❑ i.LINK (IEEE1394)
❑ DVD-ROM drive
❑ Modem
❑ DVD-R/-RW drive
❑ LAN
❑ DVD Multi drive
❑ Wireless LAN
❑ Diskette drive
❑ Bluetooth
❑ SD card
❑ Real time clock (RTC)
TROUBLESHOOTING
❑ System start-up
System start-up
When the computer does not start properly, check the following items:
❑
Self Test
❑
Power Sources
❑
Power-on Password
9-3
User's Manual
Self test
When the computer starts up, the self test will be run automatically, and the
following will be displayed:
In Touch with Tomorrow
TOSHIBA
This message remains on the screen for a few seconds.
If the self test is successful, the computer tries to load the operating system.
Depending on how the Boot Priority is set in the TOSHIBA HW Setup program.
If any of the following conditions are present, the self test failed:
❑
The computer stops and does not proceed to display information or messages
except the TOSHIBA logo.
❑
Random characters appear on the screen, and the system does not function
normally.
❑
The screen displays an error message.
Turn off the computer and check all cable connections as well as PC card and
memory module connections. If the test fails again, contact your dealer.
TROUBLESHOOTING
Power
When the computer is not plugged into an AC outlet, the battery pack is the primary
power source. However, your computer has a number of other power resources,
including intelligent power supply, Real Time Clock battery. These resources are
interrelated and any one could affect apparent power problems. This section
provides check lists for AC power and the battery. If you cannot resolve a problem
after following them, the cause could lie with another power resource. In such case,
contact your dealer.
9-4
Hardware and system checklist
Overheating power down
If the computer’s internal temperature becomes too high, the computer will automatically shut down.
Problem
Procedure
Computer shuts down
and DC IN indicator
blinks orange
Leave the computer off until the computer
reaches room temperature, then turn it back on.
If the computer is still too warm, the DC IN
indicator will continue blinking when you turn on
the power. Let it cool longer and try again.
If the computer has reached room temperature
and still does not start, or if it starts but shuts
down quickly, contact your dealer.
AC power
Problem
Procedure
Universal AC adaptor
doesn’t power the
computer (DC IN
indicator does not
glow green)
Check the connections. Make sure the cord
is firmly connected to the computer and a
power outlet.
Check the condition of the cord and terminals. If
the cord is frayed or damaged, replace it. If the
terminals are soiled, wipe them with cotton or a
clean cloth.
If the universal AC adaptor still does not power the
computer, contact your dealer.
9-5
TROUBLESHOOTING
If you have trouble turning on the computer with the universal AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes
for more information.
User's Manual
Battery
If you suspect a problem with the battery, check the DC IN indicator as well as the
Battery and Slim Select Bay indicators. For information on indicators and
battery operation see Chapter 6, Power and Power-Up Modes.
Problem
Procedure
Battery doesn’t
power the computer
The battery may be discharged. Connect the
universal AC adaptor to charge the battery.
Battery doesn’t
charge when the
universal AC adaptor is
attached (Battery or
Slim Select Bay
indicator does not
glow orange.)
If the battery is completely discharged, it will
not begin charging at once. Wait a few minutes.
If the battery still does not charge, make sure the
outlet is supplying power. Plug in an appliance
and see if it works. If it doesn’t, try another power
source.
TROUBLESHOOTING
Check whether the battery is hot or cold. If the
battery is too hot or too cold, it will not charge
properly. Let it reach room temperature.
Unplug the universal AC adaptor and remove the
battery to make sure the terminals are clean. If
necessary wipe them with a soft dry cloth dipped
in alcohol.
Connect the universal AC adaptor and replace the
battery.
Make sure the battery is securely seated.
If the indicator still does not glow, the battery may
be at the end of its operating life. Replace it.
If you do not think the battery is at the end of its
operating life, see your dealer.
Battery doesn’t
power the computer
as long as expected
9-6
Check the power consumption settings in
TOSHIBA Power Saver Utility. Consider using a
power saving mode.
Hardware and system checklist
Password
Problem
Procedure
Cannot enter
or forgot password
Contact your dealer.
NOTE: For information on setting a password,
refer to Chapter 7, HW Setup and Passwords.
Keyboard
Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard.
Procedure
Some letter keys
produce numbers
Check that the numeric keypad overlay is not
selected. Press Fn + F10 and try typing again.
Output to screen
is garbled
Make sure the software you are using is not
remapping the keyboard. Remapping involves
reassigning the meaning of each key. See your
software’s documentation.
If you are still unable to use the keyboard,
consult your dealer.
LCD panel
Problem
Procedure
No display
Press hot keys Fn + F5 to change the display
priority, to make sure it is not set for an external
monitor.
9-7
TROUBLESHOOTING
Problem
User's Manual
Markings appear on
the LCD.
They might have come from contact with the
keyboard, Touch Pad. Try wiping the LCD gently
with a clean dry cloth. If markings remain, use
LCD cleaner. Be sure to let the LCD dry before
closing it.
Problems above
remain unresolved
or other problems
occur
Refer to your software’s documentation to
determine if the software is causing the
difficulty.
Contact your dealer if the problems continue.
TROUBLESHOOTING
Hard disk drive
Problem
Procedure
Computer does not
boot from hard disk
drive
Check if a diskette is in the diskette drive or a
CD-ROM is in the optical media drive. Remove
any diskette and/or CD-ROM and check Boot
priority. Refer to Chapter 7, Boot Priority.
There may be a problem with your operating
system files. Refer to your OS documentation.
Slow performance
Your files may be fragmented. Run SCANDISK
and defragmenter to check the condition of your
files and disk. Refer to your OS documentation or
online HELP for information on running
SCANDISK and the defragmenter.
As a last resort, reformat the hard disk. Then,
reload the operating system and other files.
If problems persist, contact your dealer.
9-8
Hardware and system checklist
DVD-ROM drive
For more information, refer to Chapter 4, Operating Basics.
Problem
Procedure
You cannot access
a CD/DVD in the drive
Make sure the drive’s drawer is securely
closed. Press gently until it clicks into place.
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
A foreign object in the drawer could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Some CD/DVDs
run correctly, but
others do not
The software or hardware configuration may
be causing a problem. Make sure the
hardware configuration matches your software’s
needs. Check the CD/DVD’s documentation.
Check the type of CD/DVD you are using. The
drive supports:
DVD-ROM:
DVD-ROM, DVD-Video
CD-ROM:
CD-DA, CD-Text, Photo CD (single/
multi-session), CD-ROM Mode 1,
Mode 2, CD-ROM XA Mode 2
(Form1, Form2), Enhanced CD (CDEXTRA), CD-G (Audio CD only),
Addressing Method 2
9-9
TROUBLESHOOTING
Check whether the CD/DVD is dirty. If it is, wipe
it with a clean cloth dipped in water or a neutral
cleaner. See the Media care section in Chapter 4
for details on cleaning.
User's Manual
Check the region code on the DVD. It must match
that on the DVD-ROM drive. Region codes are
listed in the Optical media section in Chapter 2,
The Grand Tour.
If problems persist, contact your dealer.
CD-RW/DVD-ROM drive
For more information, refer to Chapter 4, Operating Basics.
Problem
Procedure
You cannot access
a CD/DVD in the drive
Make sure the drive’s drawer is securely
closed. Press gently until it clicks into place.
TROUBLESHOOTING
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
A foreign object in the drawer could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe it
with a clean cloth dipped in water or a neutral
cleaner. See the Media care section in Chapter 4
for details on cleaning.
Some CD/DVDs
run correctly, but
others do not
The software or hardware configuration may
be causing a problem. Make sure the
hardware configuration matches your software’s
needs. Check the CD/DVD’s documentation.
Check the type of CD/DVD you are using. The
drive supports:
9-10
Hardware and system checklist
DVD-ROM:
DVD-ROM, DVD-Video
CD-ROM:
CD-DA, CD-Text, Photo CD (single/
multi-session), CD-ROM Mode 1,
Mode 2, CD-ROM XA Mode 2
(Form1, Form2), Enhanced CD (CDEXTRA), CD-G (Audio CD only),
Addressing Method 2
Check the region code on the DVD. It must
match that on the CD-RW/DVD-ROM drive.
Region codes are listed in the Optical media
section in Chapter 2, The Grand Tour.
Cannot write correctly
If you have trouble writing, make sure you are
observing the following precautions:
If problems persist, contact your dealer.
9-11
TROUBLESHOOTING
• Use only media recommended by TOSHIBA.
• Do not use the mouse or keyboard during
writing.
• Use only the software supplied with the
computer for recording.
• Do not run or start other software during
writing.
• Do not jar the computer during writing.
• Do not connect/ disconnect external devices
or install/remove internal cards during writing.
User's Manual
DVD-R/-RW drive
For more information, refer to Chapter 4, Operating Basics.
Problem
Procedure
You cannot access
a CD/DVD in the drive
Make sure the drive’s drawer is securely
closed. Press gently until it clicks into place.
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
TROUBLESHOOTING
A foreign object in the drawer could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe
it with a clean cloth dipped in water or a neutral
cleaner. See the Media care section in Chapter 4
for details on cleaning.
Some CD/DVDs
run correctly, but
others do not
The software or hardware configuration may
be causing a problem. Make sure the
hardware configuration matches your software’s
needs. Check the CD/DVD’s documentation.
Check the type of CD/DVD you are using. The
drive supports:
9-12
DVD-ROM:
DVD-ROM, DVD-Video
CD-ROM:
CD-DA, CD-Text, Photo CD (single/
multi-session), CD-ROM Mode 1,
Mode 2, CD-ROM XA Mode 2
(Form1, Form2), Enhanced CD (CDEXTRA), CD-G (Audio CD only),
Addressing Method 2
Hardware and system checklist
Check the region code on the DVD. It must
match that on the CD-RW/DVD-ROM drive.
Region codes are listed in the Optical media
section in Chapter 2, The Grand Tour.
Cannot write correctly
If you have trouble writing, make sure you are
observing the following precautions:
• Use only media recommended by TOSHIBA.
• Do not use the mouse or keyboard during
writing.
• Use only the software supplied with the
computer for recording.
• Do not run or start other software during
writing.
• Do not jar the computer during writing.
• Do not connect/ disconnect external devices or
install/remove internal cards during writing.
If problems persist, contact your dealer.
TROUBLESHOOTING
DVD Multi drive
For more information, refer to Chapter 4, Operating Basics.
Problem
Procedure
You cannot access
a CD/DVD in the drive
Make sure the drive’s drawer is securely
closed. Press gently until it clicks into place.
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
A foreign object in the drawer could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
9-13
User's Manual
Check whether the CD/DVD is dirty. If it is, wipe
it with a clean cloth dipped in water or a neutral
cleaner. See the Media care section in Chapter 4
for details on cleaning.
Some CD/DVDs
run correctly, but
others do not
The software or hardware configuration may
be causing a problem. Make sure the
hardware configuration matches your software’s
needs. Check the CD/DVD’s documentation.
TROUBLESHOOTING
Check the type of CD/DVD you are using. The
drive supports:
DVD-ROM:
DVD-ROM, DVD-Video
CD-ROM:
CD-DA, CD-Text, Photo CD (single/
multi-session), CD-ROM Mode 1,
Mode 2, CD-ROM XA Mode 2
(Form1, Form2), Enhanced CD (CDEXTRA), CD-G (Audio CD only),
Addressing Method 2
Check the region code on the DVD. It must
match that on the CD-RW/DVD-ROM drive.
Region codes are listed in the Optical media
section in Chapter 2, The Grand Tour.
Cannot write correctly
If you have trouble writing, make sure you are
observing the following precautions:
• Use only media recommended by TOSHIBA.
• Do not use the mouse or keyboard during
writing.
• Use only the software supplied with the
computer for recording.
9-14
Hardware and system checklist
• Do not run or start other software during
writing.
• Do not jar the computer during writing.
• Do not connect/ disconnect external devices or
install/remove internal cards during writing.
If problems persist, contact your dealer.
Diskette drive
For more information, refer to Chapter 4, Operating Basics.
Problem
Procedure
Drive does not
operate
There may be a faulty cable connection. Check
the connection to the computer and to the drive.
You cannot access
the external 3 1/2"
diskette drive
Try another diskette. If you can access the
diskette, the original diskette (not the drive) is
probably causing the problem.
TROUBLESHOOTING
If problems persist, contact your dealer.
SD card
Refer also to Chapter 8, Optional Devices.
Problem
Procedure
SD card
error occurs
Reseat the SD card to make sure it is firmly
connected.
Check the card’s documentation.
9-15
User's Manual
You cannot write
to an SD card
Make sure the card is not write protected.
You cannot read
a file
Make sure the target file is on the SD
Card inserted in the slot.
If problems persist, contact your dealer.
PC card
Refer also to Chapter 8, Optional Devices.
Problem
Procedure
PC card
error occurs
Reseat the PC card to make sure it is
firmly connected.
TROUBLESHOOTING
Make sure the connection between the external
device and the card is firm.
Check the card’s documentation.
If problems persist, contact your dealer.
Infrared port
Refer also to the documentation for your IrDA compatible device and related
software.
Problem
Procedure
Infrared devices do
not work as expected
Make sure there is no obstruction blocking
communication between the computer and the
target device.
If problems persist, contact your dealer.
9-16
Hardware and system checklist
Pointing device
If you are using a USB mouse, also refer to the USB section in this chapter and to
your mouse documentation.
Touch Pad
Problem
Procedure
On-screen pointer
does not respond to
Pad operation
The system might be busy. If the pointer is
shaped as an hourglass, wait for it to resume
its normal shape and try again to move it.
Double-tapping
does not work
Try changing the double-click speed setting in
the mouse control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Buttons tab.
The mouse pointer
moves too fast or
too slow
Try changing the speed setting in the mouse
control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Pointer Options tab.
3. Set the speed as instructed and click OK.
If problems persist, contact your dealer.
9-17
TROUBLESHOOTING
3. Set the double-click speed as instructed and
click OK.
User's Manual
USB mouse
Problem
Procedure
On-screen pointer
does not respond to
mouse operation
The system might be busy. If the pointer is
shaped as an hourglass, wait for it to resume
its normal shape and try again to move it.
Make sure the mouse is properly connected to
the USB port.
Double-clicking
does not work
Try changing the double-click speed setting in
the mouse control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Buttons tab.
TROUBLESHOOTING
3. Set the double-click speed as instructed and
click OK.
The mouse pointer
moves too fast or
too slow
Try changing the speed setting in the mouse
control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Pointer Options tab.
3. Set the speed as instructed and click OK.
The mouse pointer
moves erratically
The mouse might be dirty. Refer to your mouse
documentations for instructions on cleaning.
If problems persist, contact your dealer.
9-18
Hardware and system checklist
USB
Refer also to your USB device’s documentation.
Problem
Procedure
USB device does
not work
Check for a firm cable connection between the
USB ports on the computer and the USB device.
Make sure the USB device drivers are properly
installed. Refer to your Windows XP documentation for information on checking the drivers.
If problems persist, contact your dealer.
Memory expansion
Refer also to Chapter 8, Optional Devices, for information on installing memory
modules.
Procedure
The following message Make sure the memory module installed in the
is displayed on the
expansion slot is compatible with the computer.
Sub LCD:
If an incompatible module has been installed,
MEM0 ERROR
follow the steps below.
or
1. Disconnect the universal AC adaptor and all
MEM1 ERROR
peripheral devices
2. Remove the battery.
3. Remove the memory module.
4. Replace the battery and/or connect the
universal AC adaptor.
5. Turn on the power.
If problems persist, contact your dealer.
9-19
TROUBLESHOOTING
Problem
User's Manual
Sound system
Refer also to documentation for your audio devices.
Problem
Procedure
No sound is heard
Adjust the volume control dial.
Check the software volume settings.
Make sure the headphone connection is secure.
If problems persist, contact your dealer.
Annoying sound
is heard
You may be experiencing feedback. Refer to
Using the microphone in Chapter 4, Operating
Basics.
TROUBLESHOOTING
If problems persist, contact your dealer.
Monitor
Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation.
Problem
Procedure
Monitor does not
turn on
Make sure that the external monitor’s power
switch is on. Confirm that the external monitor’s
power cable is plugged into a working power
outlet.
No display
Try adjusting the contrast and brightness controls
on the external monitor.
Press hot keys Fn + F5 to change the display
priority and make sure it is not set for the internal
display.
9-20
Hardware and system checklist
Display error occurs
Check that the cable connecting the external
monitor to the computer is attached firmly.
If problems persist, contact your dealer.
i.LINK (IEEE1394)
Problem
Procedure
i.LINK device does
not function
Make sure the cable is securely connected to
the computer and to the device.
Make sure the device’s power is turned on.
Reinstall the drivers. Open the Windows Control
Panel and double-click the Add Hardware icon.
Follow the on-screen directions.
Restart Windows.
TROUBLESHOOTING
If problems persist, contact your dealer.
Modem
Refer to the online help files for Appendix C and D.
Problem
Procedure
Communication
software can’t
initialize modem
Make sure the computer’s internal modem
settings are correct. Refer to Phone and Modem
Properties in the Control Panel.
You can hear a dial
tone but can’t make
a call
If the call is going through a PBX machine, make
sure the communication application’s tone dial
detection feature is disabled.
9-21
User's Manual
You can also use the ATX command. Refer to the
online help files for Appendix C, AT Commands.
You place a call,
but a connection
can’t be made
Make sure the settings are correct in your
communications application.
After making a call
you can’t hear a ring
Make sure the tone or pulse selection in your
communications application is set correctly.
TROUBLESHOOTING
You can also use the ATD command. Refer to
the online help files for Appendix C, AT Commands.
Communication is
cut off unexpectedly
The computer will automatically cut off
communication when connection with the carrier
is not successful for a set time interval. Try
lengthening this time interval.
A CONNECT display
is quickly replaced by
NO CARRIER
Check the error control setting in your
communications application.
You can also use the AT\N command. Refer to
the online help files for Appendix C, AT Commands.
Character display
becomes garbled
during a
communication
In data transmission, make sure the parity bit
and stop bit settings correspond with those
of the remote computer.
Check the flow control and communication
protocol.
You cannot receive
an incoming call
9-22
Check the rings before auto answer setting in
your communications application.
Hardware and system checklist
You can also use the ATS0 command. Refer to
the online help files for Appendix D, S-registers.
If problems persist, contact your dealer.
LAN
Problem
Procedure
Cannot access LAN
Check for a firm cable connection between the
LAN jack and the LAN HUB.
Wake-up on LAN
Make sure the universal AC adaptor is connected. The
Wake-up on LAN function consumes power even
when the system is off.
does not work
If problems persist, consult your LAN administrator.
If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics.
Problem
Procedure
Cannot access
Wireless LAN
Make sure the computer’s wireless
communication switch is set to on.
If problems persist, contact your LAN administrator or dealer.
9-23
TROUBLESHOOTING
Wireless LAN
User's Manual
Bluetooth
For more information on wireless communication, refer to Chapter 4, Operating
Basics.
Problem
Procedure
Cannot access
Bluetooth device
Make sure the computer’s wireless communication switch is set to on.
Make sure the Bluetooth Manager is running and
the power to the Bluetooth device is turned on.
Make sure no optical Bluetooth PC card is
installed in the computer. The built-in Bluetooth
function and an optional Bluetooth PC card
cannot operate simutaneously.
If problems persist, contact your dealer.
TROUBLESHOOTING
Real Time Clock
Problem
Procedure
The following message is The battery for RTC is wearing. Set the date and time
Confirmation message will appear.5. Press [Y] key.
BIOS setup will terminate and the computer will be
rebooted.
Displayed on the LCD:
in BIOS setup with the following steps:
RTC battery is low or
1. Press [F1] key. BIOS setup will boot up.
CMOS checksum is
2. Set the date in [System Date].
inconsistentPress [F1]
3.Set the time in [System Time].
key to set Date/Time.
4. Press [Fn] + [R] keys ([End] key function).
Confirmation message will appear.
5. Press [Y] key. BIOS setup will terminate and the
computer will be rebooted.
9-24
TOSHIBA support
TOSHIBA support
If you require any additional help using your computer or if you are having
problems operating the computer, you may need to contact TOSHIBA for additional
technical assistance.
Before you call
Some problems you experience may be related to software or the operating system,
it is important to investigate other sources of assistance first. Before contacting
TOSHIBA, try the following:
❑
Review troubleshooting sections in the documentation for software and
peripheral devices.
❑
If a problem occurs when you are running software applications, consult the
software documentation for troubleshooting suggestions. Call the software
company’s technical support for assistance.
❑
Consult the dealer you purchased your computer and/or software from. They
are your best sources for current information and support.
Where to write
Outside of Europe
Australia
TOSHIBA Australia Pty. Ltd.
Information Systems Division
84-92 Talavera Road
North Ryde N.S.W. 2113
Sydney
Canada
TOSHIBA of Canada Ltd.
191 McNabb Street,
Markham, Ontario
L3R8H2
China
TOSHIBA Computer Systems
(Shanghai) Co., Ltd.
Bldg. 33, No. 351, Jinzang Road,
Pudong New Area,
Shanghai,
P.R. China 201206
Singapore
TOSHIBA Singapore Pte. Ltd.
438B Alexandra Road #06-01
Alexandra Technopark
Singapore 119968
9-25
TROUBLESHOOTING
If you are still unable to solve the problem and suspect that it is hardware related,
write to TOSHIBA at the nearest location listed below:
TROUBLESHOOTING
User's Manual
UnitedKingdom
United States of America
TOSHIBA America Information Systems, TOSHIBA Information Systems (U.K.)
Ltd.
Inc.
TOSHIBA Court
9740 Irvine Boulevard
Weybridge Business Park
Irvine, California 92618
Addlestone Road
USA
Weybridge, Surrey KT15 2UL
InEurope
The Rest of Europe
Germany & Austria
TOSHIBA Europe (I.E.) GmbH
TOSHIBA Europe (I.E.) GmbH
Geschäftsbereich,
Geschäftsbereich,
Deutschland-Österreich
Deutschland-Österreich
Hammfelddamm8,
Hammfelddamm8,
D-41460 Neuss, Germany
D-41460 Neuss, Germany
France
TOSHIBA Systèms France S.A.
7, Rue Ampère B.P. 131,
92804 Puteaux Cedex
Netherlands
TOSHIBA Information Systems, Benelux
B.V.
Rivium Boulevard
41 2909 LK Capelle a/d IJssel
Spain
TOSHIBA Information Systems, ESPAÑA
Parque Empresarial San Fernando
Edificio Europa, la Planta,
Escalera A 28830 Madrid
9-26
Specifications
This appendix summarizes the computer’s technical specifications.
Environmental Requirements
Conditions
Operating
Non-operating
Thermal Gradient
Wet-bulb temperature
Conditions
Ambient
temperature
Relative
humidity
5°C (41°F) to 35°C (95°F)
20% to 80%
-20°C (-4°F) to 65°C (149°F)
10% to 95%
20°C per hour maximum
26°Cmaximum
Altitude (from sea level)
Operating
Non-operating
-60 to 3,000 meters
-60 to 10,000 meters maximum
Power Requirements
Universal AC adaptor
100-240 volts AC
50 or 60 hertz (cycles per second)
Computer
15VDC
5.0 amperes
Built-in Modem
Network control unit (NCU)
Type of NCU
Type of line
Type of dialing
AA
Telephone line (analog only)
Pulse
Tone
Control command
AT commands
EIA-578 commands
Monitor function
Computer’s speaker
A-1
APPENDIX A
Appendix A
APPENDIX A
User's Manual
Communication specifications
Communication
system
Data:
Fax:
Communication
protocol
Data
ITU-T-Rec
(Former CCITT)
Bell
Fax
ITU-T-Rec
(Former CCITT)
Communication
speed
Transmitting level
V.17/V.29/V.27ter
/V.21 ch2
-10 dBm
-10 to -40 dBm
Input/output
impedance
Error correcting
600 ohms ±30%
Power supply
V.21/V.22/V.22bis/V.32
/V.32bis/V.34/V.90
103/212A
Data transmission and reception
300/1200/2400/4800/7200/9600/12000/14400/
16800/19200/21600/24000/26400/28800/31200/
33600 bps
Data reception only with V.90
28000/29333/30666/32000/33333/34666/36000/37333/
38666/40000/41333/42666/44000/45333/46666/48000/
49333/50666/52000/53333/54666/56000 bps
Fax
2400/4800/7200/9600/12000/14400 bps
Receiving level
Data compression
A-2
Full duplex
Half duplex
MNP class 4 and ITU-T V.42
MNP class 5 and ITU-T V.42bis
+3.3V (supplied by computer)
Appendix B
Display Controller and
Modes
APPENDIX B
Display controller
The display controller interprets software commands into hardware commands that
turn particular pels on or off.
The controller is an advanced Video Graphics Array (VGA) that provides Extended
Graphics Array (XGA) and Super Extended Graphics Array Plus (SXGA+) support
for the internal LCD and external monitors. The 15.0" TFT LCD panel displays up to
1024 horizontal and 768 vertical pixels and 1400 horizontal and 1050 vertical pixels.
A high-resolution external monitor connected to the computer can display up to
2048 horizontal and 1536 vertical pixels at 16 M colors.
The display controller also controls the video mode, which uses industry standard
rules to govern the screen resolution and the maximum number of colors that can be
displayed on screen.
Software written for a given video mode will run on any computer that supports the
mode.
The computer’s display controller supports all VGA and SVGA modes, the most
widely used industry standards.
B-1
User's Manual
Video modes
APPENDIX B
The computer supports video modes defined in the tables below. If your application
offers a selection of mode numbers that do not match the numbers on the table,
select a mode based on mode type, resolution, character matrix, number of colors
and refresh rates. Also, if your software supports both graphics and text modes, the
screen display may appear to operate faster using a text mode.
Table1 Video modes (VGA)
Video
mode
Type
Resolution
Character LCD
matrix
colors
(pels)
CRT
colors
Scanning
frequency
Vertical (Hz)
0, 1
VGA
Text
40 x 25
Characters
8x8
16 of 256K
16 of 256K
70
2, 3
VGA
Text
80 x 25
Characters
8x8
16 of 256K
16 of 256K
70
0*, 1* VGA
Text
40 x 25
Characters
8 x 14
16 of 256K
16 of 256K
70
2*, 3* VGA
Text
80 x 25
Characters
8 x 14
16 of 256K
16 of 256K
70
0+, 1+ VGA
Text
40 x 25
Characters
9 x 16
16 of 256K
16 of 256K
70
2+, 3+ VGA
Text
80 x 25
Characters
9 x 16
16 of 256K
16 of 256K
70
4, 5
VGA
Grph
320 x 200
Pels
8x8
4 of 256K
4 of 256K
70
6
VGA
Grph
640 x 200
Pels
8x8
2 of 256K
2 of 256K
70
7
VGA
Text
VGA
Text
80 x 25
Characters
80 x 25
Characters
9 x 14
Mono
Mono
70
9 x 16
Mono
Mono
70
7+
B-2
Appendix B
Table1 Video modes (VGA) continued
Type
Resolution
Character LCD
matrix
colors
(pels)
CRT
colors
Scanning
frequency
Vertical (Hz)
D
VGA
Grph
320 x 200
Pels
8x8
16 of 256K
16 of 256K
70
E
VGA
Grph
640 x 200
Pels
8x8
16 of 256K
16 of 256K
70
F
VGA
Grph
640 x 350
Pels
8 x 14
Mono
Mono
70
10
VGA
Grph
640 x 350
Pels
8 x 14
16 of 256K
16 of 256K
70
11
VGA
Grph
VGA
Grph
640 x 480
Pels
640 x 480
Pels
8 x 16
2 of 256K
2 of 256K
60
8 x 16
16 of 256K
16 of 256K
60
VGA
Grph
320 x 200
Pels
8x8
256 of 256K 256 of 256K
70
12
13
APPENDIX B
Video
mode
B-3
User's Manual
APPENDIX B
Table 2 Video modes (XGA)
Resolution
LCD
colors
CRT
colors
640 x 480
256/256K
256/256K
60
75
85
100
800 x 600
256/256K
256/256K
60
75
85
100
1024 x 768
256/256K
256/256K
60
75
85
100
1280 x 1024
256/256K
(Virtual)
256/256K
60
75
85
100
1600 x 1200
256/256K
(Virtual)
256/256K
60
75
85
100
1920 x 1440
256/256K
(Virtual)
256/256K
60
75
85
2048 x 1536
256/256K
(Virtual)
256/256K
60
75
B-4
Vertical
frequency (Hz)
Appendix B
Table 2 Video modes (XGA) continued
LCD
colors
CRT
colors
Vertical
frequency (Hz)
640 x 480
64K/64K
64K/64K
60
75
85
100
800 x 600
64K/64K
64K/64K
60
75
85
100
1024 x 768
64K/64K
64K/64K
60
75
85
100
1280 x 1024
64K/64K
(Virtual)
64K/64K
60
75
85
100
1600 x 1200
64K/64K
(Virtual)
64K/64K
60
75
85
100
1920 x 1440
64K/64K
(Virtual)
64K/64K
60
75
85
2048 x 1536
64K/64K
(Virtual)
64K/64K
60
75
APPENDIX B
Resolution
B-5
User's Manual
APPENDIX B
Table 2 Video modes (XGA) continued
Resolution
LCD
colors
CRT
colors
640 x 480
16M/16M
16M/16M
60
75
85
100
800 x 600
16M/16M
16M/16M
60
75
85
100
1024 x 768
16M/16M
16M/16M
60
75
85
100
1280 x 1024
16M/16M
(Virtual)
16M/16M
60
75
85
100
1600 x 1200
16M/16M
(Virtual)
16M/16M
60
75
85
100
1920 x 1440
16M/16M
(Virtual)
16M/16M
60
75
2048 x 1536
16M/16M
(Virtual)
16M/16M
60
B-6
Vertical
frequency (Hz)
Appendix B
Table 3 Video modes (Super XGA+)
LCD
colors
CRT
colors
Vertical
frequency (Hz)
640 x 480
256/256K
256/256K
60
75
85
100
800 x 600
256/256K
256/256K
60
75
85
100
1024 x 768
256/256K
256/256K
60
75
85
100
1280 x 1024
256/256K
256/256K
60
75
85
100
1400 x 1050
256/256K
256/256K
60
75
85
100
1600 x 1200
256/256K
(Virtual)
256/256K
60
75
85
100
1920 x 1440
256/256K
(Virtual)
256/256K
60
75
85
2048 x 1536
256/256K
(Virtual)
256/256K
60
75
APPENDIX B
Resolution
B-7
User's Manual
APPENDIX B
Table 3 Video modes (Super XGA+) continued
Resolution
LCD
colors
CRT
colors
640 x 480
64K/64K
64K/64K
60
75
85
100
800 x 600
64K/64K
64K/64K
60
75
85
100
1024 x 768
64K/64K
64K/64K
60
75
85
100
1280 x 1024
64K/64K
64K/64K
60
75
85
100
1400 x 1050
64K/64K
64K/64K
60
75
85
100
1600 x 1200
64K/64K
(Virtual)
64K/64K
60
75
85
100
1920 x 1440
64K/64K
(Virtual)
64K/64K
60
75
85
2048 x 1536
64K/64K
(Virtual)
64K/64K
60
75
B-8
Vertical
frequency (Hz)
Appendix B
Table 3 Video modes (Super XGA+) continued
LCD
colors
CRT
colors
Vertical
frequency (Hz)
640 x 480
16M/16M
16M/16M
60
75
85
100
800 x 600
16M/16M
16M/16M
60
75
85
100
1024 x 768
16M/16M
16M/16M
60
75
85
100
1280 x 1024
16M/16M
16M/16M
60
75
85
100
1400 x 1050
16M/16M
16M/16M
60
75
85
100
1600 x 1200
16M/16M
(Virtual)
16M/16M
60
75
85
100
1920 x 1440
16M/16M
(Virtual)
16M/16M
60
75
2048 x 1536
16M/16M
(Virtual)
16M/16M
60
APPENDIX B
Resolution
B-9
APPENDIX B
User's Manual
B-10
Appendix C
AT Commands
In most cases, you will not need to type AT commands manually. However,
there might be some occasions when you will need to do so.
This chapter describes AT commands for data mode. Fax and voice commands
are taken care of by application software.
The format for entering AT commands is:
ATXn
Any command issued is acknowledged with a response in either text or numeric
values known as result codes.
All commands and command-values accepted by the modem are described in
this section; any entry other than those listed results in an error.
+++ Escape sequence
The escape sequence allows the modem to exit data mode and enter
on-line command mode. While in on-line command mode, you can
communicate directly to your modem using AT commands. Once you
finish, you can return to data mode using the ATO command.
A pause, the length of which is set by Escape Guard Time (S12), must
be completed after an escape sequence is entered, This pause prevents
the modem from interpreting the escape sequence as data.
The value of the escape sequence character may be changed using
register S2.
A/
Repeat last command
This command repeats the last command string entered. Do not
precede this command with an AT prefix or conclude it by pressing
Enter.
C-1
APPENDIX C
where X is the AT command, and n is the specific value for that command. After
you type in the command press Enter.
User's Manual
A
Answer command
This command instructs the modem to go off-hook and answer an
incoming call.
Bn Communication standard setting
This command determines the communication standard CCITT or Bell.
B0
Selects CCITT V.22 mode when the modem is at 1200 bps.
B1
Selects Bell 212A when the modem is at 1200 bps (default).
B15
Selects V.21 when the modem is at 300 bps.
B16
Selects Bell 103J when the modem is at 300 bps (default).
Result Codes:
APPENDIX C
OK
n=0,1,15,16
ERROR Otherwise
Dn Dial
This command instructs the modem to dial a telephone number. Enter n
(the telephone number and any modifiers) after the ATD command.
Any digit or symbol (0-9, *, #, A, B, C, D) may be dialed as touch-tone
digits. Characters such as spaces, hyphens, and parentheses do not
count. They are ignored by the modem, but you may want to include
them to make the number and modifiers easier to read.
The following may be used as phone number modifiers:
C-2
P
Pulse dialing.
T
Touch-tone dialing (default).
,
Pause during dialing. Pause for time specified in Register S8
before processing the next character in the dial string.
W
Wait for dial tone. Modem waits for a second dial tone before
processing the dial string.
@
Wait for quiet answer. Wait for five seconds of silence after
dialing the number. If silence is not detected, the modem
sends a NO ANSWER result code back to the caller.
!
Hook flash. Causes the modem to go on-hook for 0.5 seconds
and then return to off-hook.
Appendix C
En
;
Return to command mode. Causes the modem to return to
command mode after dialing a number, without disconnecting
the call.
S=n
Dial a telephone number previously stored using the &Zn=X
command (See &Zn=X command for more information). The
range is 0-3.
Echo command
This command controls whether or not the characters entered from
your computer keyboard are displayed on your monitor (echoed) while
the modem is in command mode.
E0
Disables echo to the computer.
E1
Enables echo to the computer (default).
OK
APPENDIX C
Result Codes:
n=0,1
ERROR Otherwise
Hn Hook control
This command instructs the modem to go on-hook to disconnect a call,
or off-hook to make the phone line busy.
H0
Modem goes on-hook (default).
H1
Modem goes off-hook.
Result Codes:
OK
n=0,1
ERROR Otherwise
In
Request ID information
This command displays product information about the modem.
I0
Returns modem identity string and driver version number.
I3
Same as I0.
I9
Returns region ID in English.
Result Codes:
OK
n=0,3,9
ERROR Otherwise
C-3
User's Manual
Ln
Monitor speaker volume
This command sets speaker volume to low, medium, or high.
L0
Low volume.
L1
Low volume. (Same as L0)
L2
Medium volume (default).
L3
High volume.
Result Codes:
OK
n=0,1,2,3
ERROR Otherwise
Mn Monitor speaker mode
APPENDIX C
This command turns the speaker on or off.
M0
The speaker is off.
M1
The speaker is on until the modem detects the carrier signal
(default).
M2
The speaker is always on when modem is off-hook.
M3
Speaker is on until the carrier is detected, except when dialing.
Result Codes:
OK
n=0,1,2,3
ERROR Otherwise
Nn Modulation handshake
This command controls whether or not the local modem performs a
negotiated handshake at connection time with the remote modem when
the communication speed of the two modems is different.
N0
When originating or answering, this is for handshake only at
the communication standard specified by S37 and the ATB
command.
N1
When originating or answering, begin the handshake at the
communication standard specified by S37 and the ATB
command (default).
During handshake, a lower transmission speed may be
selected.
C-4
Appendix C
Result Codes:
n=0,1
OK
ERROR Otherwise
On Return on-line to data mode
O0
Instructs the modem to exit on-line command mode and return
to data mode (see AT escape sequence, +++).
O1
This command issues a retrain before returning to on-line data
mode.
O3
This command issues a rate renegotiation before returning to
on-line data mode.
Result Codes:
OK
n=0,1,3
P
Otherwise
Select pulse dialing
This command configures the modem for pulse (non touch-tone)
dialing. Dialed digits are pulsed until a T command or dial modifier is
received. Tone dial is the default setting.
Qn Result code control
Result codes are informational messages sent from the modem and
displayed on your monitor. Basic result codes are OK, CONNECT,
RING, NO CARRIER, and ERROR. The ATQ command allows the
user to turn result codes on or off.
Q0
Enables modem to send result codes to the computer (default).
Q1
Disables modem from sending result codes to the computer.
Result Codes:
OK
n=0,1
ERROR Otherwise
C-5
APPENDIX C
ERROR
User's Manual
T
Select tone dialing
This command instructs the modem to send DTMF tones while dialing.
Dialed digits are tone dialed until a P command or dial modifier is
received. This is the default setting.
Vn
DCE response format
This command controls whether result codes (including call progress
and negotiation progress messages) are displayed as words or their
numeric equivalents.
V0
Displays result codes as digits.
V1
Displays result codes as text (default).
Result Codes:
APPENDIX C
OK
n=0,1
ERROR Otherwise
Xn
Result code selection, call progress monitoring
This command selects which result codes will be used by the modem.
Command
X0
Dial tone
Busy signal
Supported Result
detect
detect
Code
Disable
Disable
OK, CONNECT, RING, NO CARRIER,
ERROR
X1
Disable
Disable
OK, RING, NO CARRIER, ERROR,
CONNECT <RATE>
X2
Enable
Disable
OK, RING, NO CARRIER, ERROR,
NODIALTONE, CONNECT <RATE>
X3
Disable
Enable
OK, RING, NO CARRIER, ERROR,
BUSY, CONNECT <RATE>,
BLACKLISTED
X4 (default) Enable
Enable
OK, RING, NO CARRIER, ERROR,
NODIALTONE, BUSY, CONNECT
<RATE>, DELAYED, BLACKLISTED,
REORDER, WARBLE, CALL WAITING
DETECTED
C-6
Appendix C
X5
Enable
Enable
OK, RING, NO CARRIER, ERROR,
NODIALTONE, BUSY, CONNECT
<RATE>, RRING, NO BONGTONE,
DELAYED, BLACKLISTED, REORDER,
WARBLE, CALL WAITING DETECTED
Dial tone detect
Disabled: The modem dials a call regardless of whether it detects a
dial tone.
Enabled:
The modem dials only upon detection of a dial tone, and
disconnects the call if the dial tone is not detected within
10 seconds.
APPENDIX C
Busy tone detect
Disabled: The modem ignores any busy tones it receives.
Enabled:
The modem monitors for busy tones.
Result Codes:
OK
n=0,1,2,3,4,5
ERROR
Zn
Otherwise
Recall stored profile
The modem performs a soft reset and restores (recalls) the configuration profile according to the parameter supplied. If no parameter is
specified, zero is assumed. Either Z0 or Z1 restores the profile.
Result Codes:
OK
n=0,1
ERROR Otherwise
&Cn Data Carrier Detect (DCD) control
Data Carrier Detect is a signal from the modem to the computer
indicating that a carrier signal is being received from a remote modem.
DCD normally turns off when the modem no longer detects the carrier
signal.
&C0
The state of the carrier from the remote modem is ignored.
DCD circuit is always on.
C-7
User's Manual
&C1
DCD turns on when the remote modem’s carrier signal is
detected, and off when the carrier signal is not detected
(default).
Result Codes:
OK
n=0,1
ERROR Otherwise
&Dn DTR control
APPENDIX C
This command interprets how the modem responds to the state of the
DTR signal and changes to the DTR signal.
&D0
Ignore. The modem ignores the true status of DTR and treats
it as always on. This should only be used if your communication software does not provide DTR to the modem
&D1
If the DTR signal is not detected while in on-line data mode,
the modem enters command mode, issues an OK result code,
and remains connected.
&D2
If the DTR signal is not detected while in on-line data mode,
the modem disconnects (default).
&D3
Reset on the on-to-off DTR transition.
Result Codes:
OK
n=0,1,2,3
ERROR Otherwise
&F Load factory settings
This command loads the configuration stored and programmed at the
factory. This operation replaces all of the command options and the Sregister settings in the active configuration with factory values.
&F
C-8
Recall factory setting as active configuration.
Appendix C
&Gn V.22bis guard tone control
This command determines which guard tone, if any, to transmit while
transmitting in the high band (answer mode). This command is only
used in V.22 and V.22bis mode. This option is not used in North
America and is for international use only.
&G0
Guard tone disabled (default).
&G1
Sets guard tone to 550 Hz.
&G2
Sets guard tone to 1800 Hz.
Result Codes:
OK
n=0,1,2
ERROR Otherwise
&Kn Local flow control selection
Disable flow control.
&K3
Enable CTS/RTS flow control (default).
&K4
Enable XON/XOFF flow control.
APPENDIX C
&K0
Result Codes:
OK
n=0,3,4
ERROR Otherwise
&Pn Select Pulse Dial Make/Break Ratio (WW)
&P0
Selects 39% - 61% make/break ratio at 10 pulses per second.
&P1
Selects 33% - 67% make/break ratio at 10 pulses per second.
&P2
Selects 33% - 67% make/break ratio at 20 pulses per second.
Result Codes:
OK
n=0,1,2
ERROR Otherwise
&Tn Self-test commands
These tests can help to isolate problems if you experience periodic
data loss or random errors.
C-9
User's Manual
&T0
Abort. Stops any test in progress.
&T1
Local analog loop. This test verifies modem operation, as well
as the connection between the modem and computer. Any
data entered at the local DTE is modulated, then demodulated,
and returned to the local DTE. To work properly, the modem
must be off-line.
Result Codes:
OK
n=0
CONNECT
n=1
ERROR
Otherwise
APPENDIX C
&V Display Current Configuration
This command displays the current configuration of the modem. If
nonvolatile memory is supported the stored profiles are displayed as
well.
&V View profiles.
&W Store current configuration
Saves the current (active) configuration (profile), including S-Registers.
The current configuration comprises a list of storable parameters
illustrated in the &V command. These settings are restored to the
active configuration upon receiving a Zn command or at power up.
Refer to the &V command.
&W
&Zn=x
Stores the current configuration.
Store telephone number
This command is used to store up to four dialing strings in the
modem’s nonvolatile memory for later dialing. The format for the
command is &Zn=“stored number” where n is the location 0-3 to which
the number should be written. The dial string may contain up to 34
characters. The ATDS=n command dials using the string stored in
location n.
Result codes:
OK
n=0, 1, 2, 3
ERROR Otherwise
C-10
Appendix C
\Nn Error control mode selection
This command determines the type of error control used by the modem
when sending or receiving data.
\N0
Buffer mode. No error control.
\N1
Direct mode.
\N2
MNP or disconnect mode. The modem attempts to connect
using MNP2-4 error control procedures. If this fails, the
modem disconnects.
This is also known as MNP reliable mode.
\N3
V.42, MNP, or buffered (default).
\N4
V.42 or disconnect. The modem attempts to connect in V.42
error control mode. If this fails, the modem disconnects.
\N5
V.42. MNP or buffered (same as \N3).
\N7
V.42. MNP or buffered (same as \N3).
Result Codes:
OK
n=0,1,2,3,4,5,7
ERROR Otherwise
\Qn Local flow control selection
\Q0
Disable flow control.
\Q1
XON/XOFF software flow control.
\Q3
CTS/RTS to DTE (default).
Result Codes:
OK
n=0,1,3
ERROR Otherwise
C-11
APPENDIX C
The modem attempts to connect in V.42 error control mode. If
this fails, it attempts to connect in MNP mode. If this fails, it
connects in buffer mode and continues operation. This is also
known as V.42/MNP auto reliable mode (same as &Q5).
User's Manual
\Vn Protocol result code
\V0
Disable protocol result code appended to DCE speed.
\V1
Enable protocol result code appended to DCE speed (default).
Result Codes:
OK
n=0,1
ERROR Otherwise
% B View numbers in blacklist
If blacklisting is in effect, this command displays the numbers for
which the last call attempted in the past two hours failed. The ERROR
result code appears in regions that do not require blacklisting.
APPENDIX C
%Cn
Data compression control
This command determines the operation of V.42bis and MNP class 5
data compression. On-line changes do not take effect until a disconnect occurs first.
%C0
V.42bis/MNP 5 disabled. No data compression.
%C3
V.42bis/MNP 5 enabled. Data compression enabled (default).
Result Codes:
OK
n=0,3
ERROR Otherwise
C-12
Appendix D
S-registers
S-registers contain the settings that determine how a number of functions of the
internal modem operate. For example, how many times to let the telephone ring
before the modem answers and how long to wait before it hangs up if a connection fails. You can also customize certain AT commands such as the escape
sequence and command line termination.
The contents of the registers are changed automatically when you modify
corresponding settings in your communication software. If you choose,
however, you can display and edit the contents of the registers manually when
the modem is in command mode. If the value is out of the acceptable range, then
an error is generated.
This chapter describes the settings for each S-register.
S-register values
The format for displaying the value of an S-register is:
APPENDIX D
ATSn?
where n is the register number. After you type in the register press Enter.
The format for modifying the value of an S-register is:
ATSn=r
where n is the register number, and r is the new register value. After you type in
the register and its new value press Enter.
NOTE: Some registers vary from one country/region to another.
D-1
User's Manual
S0
Auto answer ring number
This register determines the number of rings the modem will count
before automatically answering a call. Enter 0 (zero) if you do not want
the modem to automatically answer at all. When disabled, the modem
can only answer with an ATA command.
Range: 0-255
Default: 0
Units:
S1
rings
Ring counter
This register is read only. The value of S1 is incremented with each
ring. If no ring occurs over a six-second interval, this register is
cleared.
Range: 0-225
Default: 0
Units:
S2
rings
AT escape character (user defined)
APPENDIX D
This register determines the ASCII values used for an escape sequence. The default is the + character. The escape sequence allows the
modem to exit data mode and enter command mode when on-line.
Values greater than 127 disable the escape sequence.
Range: 0-255, ASCII decimal
Default: 43
Units:
S3
ASCII
Command line termination character
(user defined)
This register determines the ASCII values as the carriage return
character. This character is used to end command lines and result
codes.
Range: 0-127, ASCII decimal
Default: 13 (carriage return)
Units:
D-2
ASCII
Appendix D
S4
Response formatting character (user defined)
This register determines the ASCII value used as the line feed character. The modem uses a line feed character in command mode when it
responds to the computer.
Range: 0-127, ASCII decimal
Default: 10 (line feed)
Units:
S5
ASCII
Command line editing character (user defined)
This register sets the character recognized as a backspace and pertains
to asynchronous only. The modem will not recognize the backspace
character if it is set to a value that is greater than 32 ASCII. This
character can be used to edit a command line. When the echo command is enabled, the modem echoes back to the local DTE the backspace character, an ASCII space character, and a second backspace
character. This means a total of three characters are transmitted each
time the modem processes the backspace character.
Range: 0-127, ASCII decimal
Default: 8 (backspace)
Units:
Wait before dialing
This register sets the length of time, in seconds, that the modem must
wait (pause) after going off-hook before dialing the first digit of the
telephone number. The modem always pauses for a minimum of two
seconds, even if the value of S6 is less that two seconds. The wait for
dial tone call progress feature (W dial modifier in the dial string) will
override the value in register S6. This operation, however, may be
affected by some ATX options according to country/region restrictions. In some countries/regions, S6 will set dial tone detect time.
Range:
3-255
Default:
3
Units:
seconds
D-3
APPENDIX D
S6
ASCII
User's Manual
S7
Connection completion time-out
This register sets the time, in seconds, that the modem must wait
before hanging up because carrier is not detected. The timer is started
when the modem finishes dialing (originate), or goes off-hook (answer). In originate mode, the timer is reset upon detection of an answer
tone if allowed by county restriction. The timer also specifies the wait
for silence time for the @ dial modifier in seconds. S7 is not associated
with the W dial modifier.
Range: 1-255
Default: 50
Units:
S8
seconds
Comma pause time
This register sets the time, in seconds, that the modem must pause
when it encounters a comma (,) in the dial command string. In some
countries/regions, S8 will set both wait before dialing and comma
pause time.
Range: 0-255
Default: 2
APPENDIX D
Units:
seconds
S11 DTMF dialing speed
This register determines the dialing speed which is prefixed for each
country/region.
Range: 50-255
Default: 95
Units:
.001 seconds
S12 Escape guard time
This register sets the value (in 20 millisecond increments) for the
required pause after the escape sequence.
Range: 0-255
Default: 50
Units:
D-4
.02 seconds
Appendix C
S37 Dial line rate
maximum modem speed
S37 = 1
reserved
S37 = 2
1200/75 bps
S37 = 3
300 bps
S37 = 4
reserved
S37 = 5
1200 bps
S37 = 6
2400 bps
S37 = 7
4800 bps
S37 = 8
7200 bps
S37 = 9
9600 bps
S37 = 10
12000 bps
S37 = 11
14400 bps
S37 = 12
16800 bps
S37 = 13
19200 bps
S37 = 14
21600 bps
S37 = 15
24000 bps
S37 = 16
26400 bps
S37 = 17
28800 bps
S37 = 18
31200 bps
S37 = 19
33600 bps
APPENDIX D
S37 = 0 (default)
D-5
User's Manual
AT command set result codes
The following table shows the result codes.
The result code summary
APPENDIX D
Result Code
Numeric
Description
OK
0
Command executed
CONNECT
1
Modem connected to line
RING
2
A ring signal has been detected
NO CARRIER
3
Modem lost carrier signal, or does
not detect carrier signal, or does
not detect answer tone
ERROR
4
Invalid command
CONNECT 1200 EC*1
5
Connection at 1200 bps
NO DIAL TONE
6
No dial tone detected
BUSY
7
Busy signal detected
NO ANSWER
8
No quiet answer
CONNECT 2400 EC*1
10
Connection at 2400 bps
CONNECT 4800 EC*1
11
Connection at 4800 bps
CONNECT 9600 EC*1
12
Connection at 9600 bps
CONNECT 14400 EC*1
13
Connection at 14400 bps
CONNECT 19200 EC*1
14
Connection at 19200 bps
CONNECT 7200 EC*1
24
Connection at 7200 bps
CONNECT 12000 EC*1
25
Connection at 12000 bps
CONNECT 16800 EC*1
86
Connection at 16800 bps
CONNECT 300 EC*1
40
Connection at 300 bps
CONNECT 21600 EC*1
55
Connection at 21600 bps
CONNECT 24000 EC*1
56
Connection at 24000 bps
CONNECT 26400 EC*1
57
Connection at 26400 bps
CONNECT 28800 EC*1
58
Connection at 28800 bps
CONNECT 31200 EC*1
59
Connection at 31200 bps
CONNECT 33600 EC*1
60
Connection at 33600 bps
D-6
Appendix C
Result Code
Numeric
Description
DELAYED*2
88
Delay is in effect for the dialed
number
BLACKLISTED*2
89
Dialed number is blacklisted
BLACKLIST FULL*2
90
Blacklist is full
*1: EC only appears when the Extended Result Codes configuration option is
enabled. EC is replaced by one of the following symbols, depending upon
the error control method used:
V.42bis - V.42 error control and V.42bis data compression.
V.42 - V.42 error control only.
MNP 5 - MNP class 4 error control and MNP class 5 data compression.
MNP 4 - MNP class 4 error control only.
NoEC - No error control protocol.
*2: In some countries/regions, these result codes may not appear.
APPENDIX D
D-7
APPENDIX D
User's Manual
D-8
Appendix E
V.90
The TOSHIBA internal modem uses V.90 technology. The modem is capable of
downstream speeds of 56Kbps (kilobits per second) when connected to an Internet
service provider that supports V.90. As with any modem, the actual throughput
(speed of data transfer) depends on analog telephone line conditions, which can
vary considerably. Therefore, many users will experience throughput in the range of
28-50Kbps under normal telephone line conditions. Upstream data flows at the V.34
rate.
NOTE: V.90 rates can be achieved only when one V.90-capable host
modem is connected to another. The TOSHIBA Internal modem will select
automatically V.34 if the remote modem lacks V.90 capability or if a
combination of network and/or phone line conditions prevent V.90
connection.
V.90 mode
Function
Transmission speed
Data V.90
From 56K (maximum) to 28Kbps (minimum)
Reception only
APPENDIX E
E-1
User's Manual
APPENDIX E
Table E-1 Result codes for a V.90 connection
No.
Result code
Description
70
CONNECT 32000 EC*
Connection at 32000 bps
72
CONNECT 36000 EC*
Connection at 36000 bps
74
CONNECT 40000 EC*
Connection at 40000 bps
76
CONNECT 44000 EC*
Connection at 44000 bps
78
CONNECT 48000 EC*
Connection at 48000 bps
80
CONNECT 52000 EC*
Connection at 52000 bps
82
CONNECT 56000 EC*
Connection at 56000 bps
100
CONNECT 28000 EC*
Connection at 28000 bps
101
CONNECT 29333 EC*
Connection at 29333 bps
102
CONNECT 30666 EC*
Connection at 30666 bps
103
CONNECT 33333 EC*
Connection at 33333 bps
104
CONNECT 34666 EC*
Connection at 34666 bps
105
CONNECT 37333 EC*
Connection at 37333 bps
106
CONNECT 38666 EC*
Connection at 38666 bps
107
CONNECT 41333 EC*
Connection at 41333 bps
108
CONNECT 42666 EC*
Connection at 42666 bps
109
CONNECT 45333 EC*
Connection at 45333 bps
110
CONNECT 46666 EC*
Connection at 46666 bps
111
CONNECT 49333 EC*
Connection at 49333 bps
112
CONNECT 50666 EC*
Connection at 50666 bps
113
CONNECT 53333 EC*
Connection at 53333 bps
114
CONNECT 54666 EC*
Connection at 54666 bps
E-2
Appendix E
* EC stands for the Error Control method, which appears only when the extended
result codes configuration option is enabled. EC is replaced by one of the
following symbols, depending on the error control method used.
V42bis
V42
NoEC
V.42 error control and V.42bis data compression
V.42 error control only
No error control protocol
AT Command
-V90=* V.90 Dial Line Rate
-V90 sets the maximum V.90 downstream that the modem attempts to
connect.
-V90=0 V.90 disabled
-V90=1 V.90 enabled: automatic speed selection - maximum modem speed
(default)
APPENDIX E
E-3
APPENDIX E
User's Manual
E-4
Internal Modem Guide
This appendix describes how to install and the remove the internal modem.
CAUTION: Do not disassemble the computer beyond the steps described
in this instruction or touch any components not specifically described.
Installing the internal modem
NOTE: The internal modem is preinstalled. The following is for information only.
To install the internal modem follow the procedures below.
Installing the modem board and jack
To install the modem board and jack, follow the steps below.
1. Save your data and turn off the computer.
2. Disconnect the AC adaptor and other peripheral devices.
3. Turn the computer upside down and remove the battery pack.
4. Remove one screw securing the Hard Disk Drive cover.
F-1
APPENDIX F
Appendix F
APPENDIX F
User's Manual
5. Pull the guide (plastic tab) toward the direction shown by arrow, then lift the
HDD. Be careful not to damage the connector.
GUIDE
(PLASTIC TAB)
6. Remove two screws, which you use later to secure the modem board.
7. Connect the modem board cable and seat the modem board.
8. Secure the modem board with two screws removed in step 6.
9. Secure the cover with one screw.
Removing the internal modem
To remove the internal modem, follow the steps below.
1. Save your data and turn off the computer.
2. Disconnect the AC adaptor and any other peripheral device.
3. Turn the computer upside down and remove the battery pack.
4. Remove one screw securing the Hard Disk Drive cover.
5. Pull the guide (plastic tab) toward the direction shown by arrow, then lift the
HDD. Be careful not to damage the connector.
6. Remove two screws and remove the modem board.
7. Disconnect the modem cable.
8. Secure the modem cover with one screw.
9. Install the battery pack.
Refer to the installation procedures for details.
F-2
Appendix G
Wireless LAN
Form Factor
Capability
Network Operating
System
Media Access
Protocol
Data Rate
- Mini PCI TypeIII
- EEE 802.11 Standard for Wireless LANS (DSSS)
Wi-Fi (Wireless Fidelity) certified by the Wireless Ethernet
Compatibility Alliance (WECA)
- Microsoft Windows® Networking
- CSMA/CA (Collision Avoidance) with Acknowledgment
(ACK)
- 54/48/36/24/18/12/9/6 Mb/s (Revision A)
- 11/5.5/2/1 Mb/s (Revision B)
- 108/96/72/48/36/24/18/12 Mb/s (Turbo Mode)
Radio Characteristics
Radio Characteristics of Wireless LAN Cards may vary according to:
❑
country/region where the product was purchased
❑
Type of product
Wireless communication is often subject to local radio regulations. Although
Wireless LAN Wireless networking products have been designed for operation in
the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number
of limitations to the use of wireless communication equipment.
NOTE: Refer to the flyer “Information to the User” for regulatory
information that may apply in your country/region.
R-F Frequency
- Band 5GHz (5150-5850 MHz) (Revision A, Turbo Mode)
- Band2.4GHz (2400-2483.5 MHz) (Revision B)
G-1
APPENDIX G
Card Specifications
User's Manual
Modulation Technique Direct Sequence Spread Spectrum
- CCK, DQPSK, DBPSK (Revision B)
- OFDM-BPSK, OFDM-QPSK, OFDM-16QAM, OFDM64QAM (Revision A, Turbo Mode)
APPENDIX G
The range of the wireless signal is related to the Transmit Rate of the wireless
communication. Communications at lower Transmit range may travel larger
distances.
❑
The range of your wireless devices can be affected when the antennas are
placed near metal surfaces and solid high-density materials.
❑
Range is also impacted due to "obstacles" in the signal path of the radio that
may either absorb or reflect the radio signal.
Supported Frequency Sub-bands
Subject to the radio regulations that apply in your country, your Wireless LAN
Card may support a different set of 5GHz / 2.4GHz channels.
Consult your Authorized Wireless LAN or TOSHIBA Sales office for information
about the radio regulations that apply in your country/region.
Wireless IEEE 802.11 Channels Sets (Revision B)
Frequency Range
2400-2472MHz
Channel ID
1
2412
2
2417
3
2422
4
2427
5
2432
6
2437
7
2442
8
2447
9
2452
10
2457*
11
2462
* Factory-set default channels
G-2
Appendix G
When installing Wireless LAN Cards, the channel configuration is managed as
follows:
For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless
LAN Card will automatically start operation at the channel identified by the
Wireless LAN Access Point, When roaming between different access points
the station can dynamically switch to another channel if required.
❑
For Wireless LAN Cards installed in Wireless clients that operating in a peerto-peer mode, the card will use the default channel 10.
❑
In a Wireless LAN Access Point, the Wireless LAN card will use the factoryset default channel (printed in bold), unless the LAN Administrator selected a
different channel when configuring the Wireless LAN Access Point device.
Wireless IEEE 802.11 Channels Sets (Revision A)
Frequency Range
5150-5850MHz
Note
Channel ID
36
5180
40
5200
44
5220
48
5240
52
5260
56
5280
60
5300
64
5320
149
5745
US only *1
153
5765
US only *1
157
5785
US only *1
161
5805
US only *1
*1: Available Area: US (USA, CANADA) only
A peer-to-peer mode is available under the following condition;
A Wireless LAN card receive a "US country code" beacon of the standard
IEEE802.11 (Revision D) from the near Wireless LAN Access Point.
G-3
APPENDIX G
❑
User's Manual
Wireless Channels Sets (Turbo Mode)
Frequency Range
5150-5850MHz
Note
42
5210
US only *1
50
5250
US only *1
58
5290
US only *1
152
5760
US only *1
160
5800
US only *1
APPENDIX G
Channel ID
*1: Available Area: US (USA, CANADA) only
A peer-to-peer mode is available under the following condition;
A Wireless LAN card receive a "US country code" beacon of the standard
IEEE802.11 (Revision D) from the near Wireless LAN Access Point.
G-4
Appendix H
AC Power Cord and
Connectors
The power cord’s AC input plug must be compatible with the various international
AC power outlets and the cord must meet the standards for the country/region in
which it is used. All cords must meet the following specifications:
Minimum 2 meters
Wire size:
Minimum 0.75 mm2
Current rating:
Minimum 2.5 amperes
Voltage rating:
125 or 250 VAC
(depending on country/region’s power standards)
Certification agencies
U.S. and Canada: UL listed and CSA certified
No. 18 AWG, Type SVT or SPT-2 two conductor
Europe:
Austria:
OVE
Italy:
IMQ
Belgium:
CEBEC
The Netherlands:
KEMA
Denmark:
DEMKO
Norway:
NEMKO
Finland:
SETI
Sweden:
SEMKO
France:
UTE
Switzerland:
SEV
Germany:
VDE
United Kingdom:
BSI
Australia:
AS
Japan:
DENANHO
In Europe, power cords must be VDE type, H05VVH2-F and two conductor.
For the United States and Canada, plug configuration must be a 2-15P (250 V) or 115P (125 V) as designated in the U.S. National Electrical code handbook and the
Canadian Electrical Code Part II.
H-1
APPENDIX H
Length:
User's Manual
The following illustrations show the plug shapes for the U.S.A. and Canada, the
United Kingdom, Australia and Europe.
APPENDIX H
USA and Canada
UL approved
CSA approved
Australia
AS approved
H-2
United Kingdom
BS approved
Europe
Approved by the
appropriate agency
Appendix I
Parts Numbers
The computer configuration and parts numbers, printed on a label on the bottom of
the computer, indicate the CPU, LCD, memory, HDD, Slim Select Bay modules
and communication devices.
APPENDIX I
I-1
User's Manual
Configurations
The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the
label. The explanations are to the left of the shading. Abbreviations are not limited to those in this chart. They may change
without notice.
APPENDIX I
CPU
Pentium4
DT P4 2.26
DT P4 2.4
DT P4 2.53
DT P4 2.66
DT P4 2.8
P4-2.26
P4-2.4
P4-2.53
P4-2.66
P4-2.8
LCD
15"TFT-XGA
15"TFT-SXGA+
Memory
15X
15+
128MB
128+128MB
256MB
256+128MB
256+256MB
512MB
512+128MB
512+256MB
512+512MB
128MB
256MB
256MB
384MB
512MB
512MB
640MB
768MB
1024MB
HDD
30GB
40GB
60GB
Slim Select Bay
30 DVD-ROM
40 CD-RW/DVD-ROM
60 DVD-R/DVD-RW
DVD-Multi
DVD
RW/DV
DVR
DRM
Communication
802.11b
802.11a/b combo
802.11b/BT
802.11b/ combo/BT
WLb
WLab
WLb/BT
WLab/BT
*Figures indicate the CPU operating speed in megahertz. For example, P4-2.4 means Intel® Pentium®4 processor 2.40GHz.
I-2
The terms in this glossary cover topics related to this manual. Alternate naming
is included for reference.
Abbreviations
IDE: integrated drive electronics
AC: alternating current
I/O: input/output
AGP: accelerated graphics port
IrDA: Infrared Data Association
ANSI: American National Standards
Institute
IRQ: interrupt request
APM: advanced power manager
LCD: liquid crystal display
ASCII: American Standard Code for
Information Interchange
LED: light emitting diode
BIOS: basic input output system
CD-ROM: Compact Disc-Read Only
Memory
KB: kilobyte
LSI: large scale integration
MS-DOS: Microsoft Disk Operating
System
CD-RW: Compact Disc-Read/Write
OCR: optical character recognition
(reader)
CMOS: complementary metal-oxide
semiconductor
PCB: printed circuit board
CPU: central processing unit
PCI: peripheral component interconnect
CRT: cathode ray tube
RAM: random access memory
DC: direct current
RGB: red, green, and blue
DDC: display data channel
ROM: read only memory
DMA: direct memory access
RTC: real time clock
DOS: disk operating system
DVD: digital versatile disc
SCSI: small computer system
interface
ECP: extended capabilities port
SIO: serial input/output
FDD: floppy disk drive
SXGA+: super extended graphics
array plus
FIR: fast infrared
HDD: hard disk drive
Glossary-1
GLOSSARY
Glossary
GLOSSARY
Adaptor
(Abbreviations continued)
TFT: thin-film transistor
UART: universal asynchronous
receiver/transmitter
USB: Universal Serial Bus
UXGA: ultra extended graphics array
VESA: Video Electronic Standards
Association
VGA: video graphics array
VRT: voltage reduction technology
XGA: extended graphics array
A
adaptor: A device that provides an
interface between two dissimilar
electronic devices. For example, the
AC adaptor modifies the power from a
wall outlet for use by the computer.
This term also refers to the add-in
circuit cards that control external
devices, such as video monitors and
magnetic tape devices.
allocate: To assign a space or
function for a specific task.
alphanumeric: Keyboard characters
including letters, numbers and other
symbols, such as punctuation marks or
mathematical symbols.
alternating current (AC): Electric
current that reverses its direction of
flow at regular intervals.
Glossary-2
analog signal: A signal whose
characteristics such as amplitude and
frequency vary in proportion to (are an
analog of) the value to be transmitted.
Voice communications are analog
signals.
ANSI: American National Standards
Institute. An organization established
to adopt and define standards for a
variety of technical disciplines. For
example, ANSI defined the ASCII
standard and other information
processing requirements.
antistatic: A material used to prevent
the buildup of static electricity.
application: A group of programs
that together are used for a specific
task such as accounting, financial
planning, spreadsheets, word processing and games.
ASCII: American Standard Code for
Information Interchange. ASCII code is
a set of 256 binary codes that represent
the most commonly used letters,
numbers, and symbols.
async: Short for asynchronous.
asynchronous: Lacking regular time
relationship. As applied to computer
communications, asynchronous refers
to the method of transmitting data that
does not require a steady stream of
bits to be transmitted at regular time
intervals.
cache memory
backup: A duplicate copy of files kept
as a spare in case the original is
destroyed.
batch file: A file that can be executed
from the system prompt containing a
sequence of operating system commands or executable files.
binary: The base two number system
composed of zeros and ones (off or
on), used by most digital computers.
The right-most digit of a binary number
has a value of 1, the next a value of 2,
then 4, 8, 16, and so on. For example,
the binary number 101 has a value of 5.
See also ASCII.
BIOS: Basic Input Output System.
The firmware that controls data flow
within the computer. See also firmware.
bit: Derived from "binary digit," the
basic unit of information used by the
computer. It is either zero or one. Eight
bits is one byte. See also byte.
Bluetooth: A short-range radio
technology designed to simplify
wireless communication among
computers, communication devices
and the Internet.
board: A circuit board. An internal
card containing electronic components, called chips, which perform a
specific function or increase the
capabilities of the system.
boot: Short for bootstrap. A program
that starts or restarts the computer.
The program reads instructions from a
storage device into the computer’s
memory.
bps: Bits per second. Typically used
to describe the data transmission
speed of a modem.
buffer: The portion of the computer’s
memory where data is temporarily
stored. Buffers often compensate for
differences in the rate of flow from one
device to another.
bus: An interface for transmission of
signals, data or electric power.
byte: The representation of a single
character. A sequence of eight bits
treated as a single unit; also the
smallest addressable unit within the
system.
C
cache memory: High speed memory
which stores data that increases
processor speed and data transfer rate.
When the CPU reads data from main
memory, it stores a copy of this data in
cache memory. The next time the CPU
needs that same data, it looks for it in
the cache memory rather than the main
memory, which saves time. The
computer has two cache levels. Level
one is incorporated into the processor
and level two resides in external
memory.
Glossary-3
GLOSSARY
B
GLOSSARY
capacity
capacity: The amount of data that can
be stored on a magnetic storage
device such as a diskette (floppy disk)
or hard disk. It is usually described in
terms of kilobytes (KB), where one KB
= 1024 bytes and megabytes (MB),
where one MB = 1024 KB.
CMOS: Complementary Metal-Oxide
Semiconductor. An electronic circuit
fabricated on a silicon wafer that
requires very little power. Integrated
circuits implemented in CMOS
technology can be tightly packaged
and are highly reliable.
card: Synonym for board. See board.
cold start: Starting a computer that is
currently off (turning on the power).
CardBus: An industry standard bus
for 32-bit PC cards.
CD-ROM: A Compact Disc-Read
Only Memory is a high capacity disc
that can be read from but not written
to. The CD-ROM drive uses a laser,
rather than magnetic heads, to read
data from the disc.
CD-R: A Compact Disc-Recordable
disc can be written once and read
many times. See also CD-ROM.
CD-RW: A Compact Disc-Read/Write
disc can be rewritten many times. See
also CD-ROM.
character: Any letter, number,
punctuation mark, or symbol used by
the computer. Also synonymous with
byte.
chassis: The frame containing the
computer.
chip: A small semiconductor containing computer logic and circuitry for
processing, memory, input/output
functions and controlling other chips.
Glossary-4
COM1, COM2, COM3 and COM4:
The names assigned to the serial and
communication ports.
commands: Instructions you enter at
the terminal keyboard that direct the
actions of the computer or its peripheral devices.
communications: The means by
which a computer transmits and
receives data to and from another
computer or device. See parallel
interface; serial interface.
Compact Flash: A small removable
mass storage device, designed with
flash technology, a non-volatile
storage solution that does not require
a battery to retain data indefinitely.
compatibility: 1) The ability of one
computer to accept and process data in
the same manner as another computer
without modifying the data or the
media upon which it is being transferred. 2) the ability of one device to
connect to or communicate with
another system or component.
dielete
computer program: A set of instructions written for a computer that
enable it to achieve a desired result.
computer system: A combination of
hardware, software, firmware, and
peripheral components assembled to
process data into useful information.
configuration: The specific components in your system (such as the
terminal, printer, and disk drives) and
the settings that define how your
system works. You use the HW Setup
program to control your system
configuration.
CRT: Cathode Ray Tube. A vacuum
tube in which beams projected on a
fluorescent screen-producing
luminous spots. An example is the
television set.
cursor: A small, blinking rectangle or
line that indicates the current position
on the display screen.
D
data: Information that is factual,
measurable or statistical that a
computer can process, store, or
retrieve.
control keys: A key or sequence of
keys you enter from the keyboard to
initiate a particular function within a
program.
data bits: A data communications
parameter controlling the number of
bits (binary digits) used to make up a
byte. If data bits = 7 the computer
can generate 128 unique characters.
If data bits = 8 the computer can
generate 256 unique characters.
controller: Built-in hardware and
software that controls the functions of
a specific internal or peripheral device
(e.g. keyboard controller).
DC: Direct Current. Electric current
that flows in one direction. This type
of power is usually supplied by
batteries.
co-processor: A circuit built into the
processor that is dedicated to intensive
math calculations.
default: The parameter value
automatically selected by the system
when you or the program do not
provide instructions. Also called a
preset value.
CPS: Characters Per Second. Typically used to indicate the transmission
speed of a printer.
CPU: Central Processing Unit. The
portion of the computer that interprets
and executes instructions.
delete: To remove data from a disk or
other data storage device. Synonymous with erase.
Glossary-5
GLOSSARY
components: Elements or parts (of a
system) which make up the whole
(system).
GLOSSARY
device driver
device driver: A program that controls
communication between a specific
peripheral device and the computer.
The CONFIG.SYS file contains device
drivers that MS-DOS loads when you
turn the computer on.
dialog box: A window that accepts
user input to make system settings or
record other information.
disk drive: The device that randomly
accesses information on a disk and
copies it to the computer’s memory. It
also writes data from memory to the
disk. To accomplish these tasks, the
unit physically rotates the disk at high
speed past a read-write head.
disk storage: Storing data on magnetic disk. Data is arranged on
concentric tracks much like a phonograph record.
diskette: A removable disk that stores
magnetically encoded data. Also
called a floppy disk.
display: A CRT, LCD, or other image
producing device used to view
computer output.
documentation: The set of manuals
and/or other instructions written for the
users of a computer system or application. Computer system documentation
typically includes procedural and
tutorial information as well as system
functions.
DOS: Disk Operating System. See
operating system.
Glossary-6
driver: A software program, generally
part of the operating system, that
controls a specific piece of hardware
(frequently a peripheral device such as
a printer or mouse).
DVD-RAM: A Digital Versatile Disc
Random Access Memory is a highcapacity, high performance disc that
lets you store large volumes of data.
The DVD-ROM drive uses a laser to
read data from the disc.
DVD-ROM: A Digital Versatile Disc
Read Only Memory is a high capacity,
high performance disc suitable for
play back of video and other highdensity files. The DVD-ROM drive
uses a laser to read data from the disc.
E
echo: To send back a reflection of the
transmitted data to the sending
device. You can display the information on the screen, or output it to the
printer, or both. When a computer
receives back data it transmitted to a
CRT (or other peripheral device) and
then retransmits the data to printer,
the printer is said to echo the CRT.
erase: See delete.
escape: 1) A code ( ASCII code 27),
signaling the computer that what
follows are commands; used with
peripheral devices such as printers
and modems. 2) A means of aborting
the task currently in progress.
hard disk drive (HDD)
execute: To interpret and execute an
instruction.
folder: An icon in Windows used to
store documents or other folders.
format: The process of readying a
blank disk for its first use. Formatting
establishes the structure of the disk
that the operating system expects
before it writes files or programs onto
the disk.
Extended Capability Port: An industry
standard that provides a data buffer,
switchable forward and reverse data
transmission, and run length encoding
(RLE) support.
function keys: The keys labeled F1
through F12 that tell the computer to
perform certain functions.
F
gigabyte (GB): A unit of data storage
equal to 1024 megabytes. See also
megabyte.
fast infrared: An industry standard
that enables cableless infrared serial
data transfer at speeds of up to 4
Mbps.
file: A collection of related information; a file can contain data, programs,
or both.
firmware: A set of instructions built
into the hardware which controls and
directs a microprocessor’s activities.
G
graphics: Drawings, pictures, or other
images, such as charts or graphs, to
present information.
H
floppy disk: See diskette.
hard disk: A non-removable disk
usually referred to as drive C. The
factory installs this disk and only a
trained engineer can remove it for
servicing. Also called fixed disk.
floppy disk drive (FDD): An electromechanical device that reads and
writes to floppy disks. See also
diskette.
hard disk drive (HDD): An
electromechanical device that reads
and writes a hard disk. See also hard
disk.
fixed disk: See hard disk.
Fn-esse: A TOSHIBA utility that lets
you assign functions to hot keys.
Glossary-7
GLOSSARY
escape guard time: A time before and
after an escape code is sent to the
modem which distinguishes between
escapes that are part of the transmitted
data, and escapes that are intended as
a command to the modem.
GLOSSARY
hardware
hardware: The physical electronic
and mechanical components of a
computer system: typically, the
computer itself, external disk drives,
etc. See also software and firmware.
hertz: A unit of wave frequency that
equals one cycle per second.
hexadecimal: The base 16 numbering
system composed of the digits 0
through 9 and the letters A, B, C, D, E,
and F.
host computer: The computer that
controls, regulates, and transmits
information to a device or another
computer.
hot key: The computer’s feature in
which certain keys in combination with
the extended function key, Fn, can be
used to set system parameters, such
as speaker volume.
HW Setup: A TOSHIBA utility that
lets you set the parameters for various
hardware components.
I
icon: A small graphic image displayed
on the screen or in the indicator panel.
In Windows, an icon represents an
object that the user can manipulate.
i.LINK (IEEE1394): This port enables
high-speed data transfer directly from
external devices such as digital video
cameras.
Glossary-8
infrared port: A cableless communications port capable of using infrared
signals to send serial data.
input: The data or instructions you
provide to a computer, communication
device or other peripheral device from
the keyboard or external or internal
storage devices. The data sent (or
output) by the sending computer is
input for the receiving computer.
instruction: Statements or commands
that specify how to perform a particular task.
interface: 1) Hardware and/or
software components of a system
used specifically to connect one
system or device to another. 2) To
physically connect one system or
device to another to exchange
information. 3) The point of contact
between user, the computer, and the
program, for example, the keyboard or
a menu.
interrupt request: A signal that gives
a component access to the processor.
I/O: Input/output. Refers to acceptance and transfer of data to and from
a computer.
I/O devices: Equipment used to
communicate with the computer and
transfer data to and from it.
IrDA 1.1: An industry standard that
enables cableless infrared serial data
transfer at speeds of up to 4 Mbps.
menu
jumper: A small clip or wire that
allows you to change the hardware
characteristics by electrically connecting two points of a circuit.
K
K: Taken from the Greek word kilo,
meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th
power. See also byte and kilobyte.
KB: See kilobyte.
keyboard: An input device containing switches that are activated by
manually pressing marked keys. Each
keystroke activates a switch that
transmits a specific code to the
computer. For each key, the transmitted code is, in turn, representative of
the (ASCII) character marked on the
key.
kilobyte (KB): A unit of data storage
equal to 1024 bytes. See also byte
and megabyte.
L
level 2 cache: See cache.
Light Emitting Diode (LED): A
semiconductor device that emits light
when a current is applied.
Liquid Crystal Display (LCD): Liquid
crystal sealed between two sheets of
glass coated with transparent conducting material. The viewing-side
coating is etched into character
forming segments with leads that
extend to the edge of the glass.
Applying a voltage between the glass
sheets alters the brightness of the
liquid crystal.
LSI: Large Scale Integration. 1) A
technology that allows the inclusion
of up to 100,000 simple logic gates on
a single chip. 2) An integrated circuit
that uses large scale integration.
M
main board: See motherboard.
megabyte (MB): A unit of data
storage equal to 1024 kilobytes. See
also kilobyte.
megahertz: A unit of wave frequency
that equals 1 million cycles per
second. See also hertz.
Memory Stick: An IC recording
media designed to record various
kinds of digital content such as still
and moving images, music and
computer data on a single stick.
menu: A software interface that
displays a list of options on the
screen. Also called a screen.
Glossary-9
GLOSSARY
J
GLOSSARY
microprocessor
microprocessor: A hardware component contained in a single integrated
circuit that carries out instructions.
Also called the central processing unit
(CPU), one of the main parts of the
computer.
N
mode: A method of operation, for
example, the boot mode, standby mode
or the hibernation mode.
nonvolatile memory: Memory, usually
read-only (ROM), that is capable of
permanently storing information.
Turning the computer’s power off
does not alter data stored in nonvolatile memory.
modem: Derived from modulator/
demodulator, a device that converts
(modulates) digital data for transmission over telephone lines and then
converts modulated data (demodulates) to digital format where received.
monitor: A device that uses rows and
columns of pixels to display alphanumeric characters or graphic images.
See also CRT.
motherboard: A name sometimes
used to refer to the main printed circuit
board in processing equipment. It
usually contains integrated circuits
that perform the processor’s basic
functions and provides connectors for
adding other boards that perform
special functions. Sometimes called a
main board.
MP3: An audio compression standard
that enables high-quality transmission
and real-time playback of sound files.
Glossary-10
non-system disk: A formatted diskette
(floppy disk) you can use to store
programs and data but you cannot use
to start the computer. See system disk.
numeric keypad overlay: A feature
that allows you to use certain keys on
the keyboard to perform numeric entry,
or to control cursor and page movement.
O
OCR: Optical Character Recognition
(reader). A technique or device that
uses laser or visible light to identify
characters and input them into a
storage device.
online state: A functional state of a
peripheral device when it is ready to
receive or transmit data.
operating system: A group of
programs that controls the basic
operation of a computer. Operating
system functions include interpreting
programs, creating data files, and
controlling the transmission and
receipt (input/output) of data to and
from memory and peripheral devices.
prompt
peripheral device: An I/O device that
is external to the central processor
and/or main memory such as a printer
or a mouse.
P
plug and play: A capability with
Windows that enables the system to
automatically recognize connections
of external devices and make the
necessary configurations in the
computer.
parallel interface: Refers to a type of
information exchange that transmits
information one byte (8 bits) at a time.
See also serial interface.
parity: 1) The symmetrical relationship between two parameter values
(integers) both of which are either on
or off; odd or even; 0 or 1. 2) In serial
communications, an error detection bit
that is added to a group of data bits
making the sum of the bits even or
odd. Parity can be set to none, odd, or
even.
pixel: A picture element. The smallest
dot that can be made on a display or
printer. Also called a pel.
port: The electrical connection
through which the computer sends
and receives data to and from devices
or other computers.
Power Saver Utility: A TOSHIBA
utility that lets you set the parameters
for various power-saving functions.
password: A unique string of characters used to identify a specific user.
The computer provides various levels
of password protection such as user,
supervisor and eject.
printed circuit board (PCB): A
hardware component of a processor to
which integrated circuits and other
components are attached. The board
itself is typically flat and rectangular,
and constructed of fiberglass, to form
the attachment surface.
pel: The smallest area of the display
that can be addressed by software.
Equal in size to a pixel or group of
pixels. See pixel.
program: A set of instructions a
computer can execute that enables it
to achieve a desired result. See also
application.
peripheral component interconnect:
An industry standard 32-bit bus.
prompt: A message the computer
provides indicating it is ready for or
requires information or an action from
you.
Glossary-11
GLOSSARY
output: The results of a computer
operation. Output commonly indicates data 1) printed on paper, 2)
displayed at a terminal, 3) sent
through the serial port of internal
modem, or 4) stored on some magnetic media.
GLOSSARY
Radio frequency interference (RFI) shield
R
Radio frequency interference (RFI)
shield: A metal shield enclosing the
printed circuit boards of the printer or
computer to prevent radio and TV
interference. All computer equipment
generates radio frequency signals.
The FCC regulates the amount of
signals a computing device can allow
past its shielding. A Class A device is
sufficient for office use. Class B
provides a more stringent classification for home equipment use.
TOSHIBA portable computers comply
with Class B computing device
regulations.
Random Access Memory (RAM):
High speed memory within the
computer circuitry that can be read or
written to.
restart: Resetting a computer without
turning it off (also called “warm boot”
or “soft reset”). See also boot.
RGB: Red, green, and blue. A device
that uses three input signals, each
activating an electron gun for a
primary additive color (red, green, and
blue) or port for using such a device.
See also CRT.
RJ11: A modular telephone jack.
RJ45: A modular LAN jack.
Glossary-12
ROM: Read Only Memory: A
nonvolatile memory chip manufactured to contain information that
controls the computer’s basic
operation. You cannot access or
change information stored in ROM.
S
SCSI: Small Computer System
Interface is an industry standard
interface for connection of a variety of
peripheral devices.
SD cards: Secure Digital cards are
flash memory widely used in a variety
of digital devices such as digital
cameras and Personal Digital Assistants.
SIO: Serial Input/Output. The
electronic methodology used in serial
data transmission.
Smart media: A storage card of
about one-thirds of the area of a
conventional PC card and only
0.76mm thickness. It can be used in
equipment that requires a removable
memory chip for portability.
soft key: Key combinations that
emulate keys on the IBM keyboard,
change some configuration options,
stop program execution, and access
the numeric keypad overlay.
write protection
TouchPad: A pointing device integrated into the TOSHIBA computer
palm rest.
stop bit: One or more bits of a byte
that follow the transmitted character or
group codes in asynchronous serial
communications.
U
subpixel: Three elements, one red,
one green and blue (RGB), that make
up a pixel on the color LCD. The
computer sets subpixels independently, each may emit a different
degree of brightness. See also pixel.
synchronous: Having a constant time
interval between successive bits,
characters or events.
system disk: A disk that has been
formatted with an operating system.
For MS-DOS the operating system is
contained in two hidden files and the
COMMAND.COM file. You can boot a
computer using a system disk. Also
called an operating system disk.
T
terminal: A typewriter-like keyboard
and CRT display screen connected to
the computer for data input/output.
TFT: Transistor-transistor logic. A
logic circuit design that uses switching transistors for gates and storage.
TTL: Transistor-transistor logic. A
logic circuit design that uses switching transistors for gates and storage.
Universal Serial Bus: This serial
interface lets you communicate with
several devices connected in a chain
to a single port on the computer.
V
VGA: Video Graphics Array is an
industry standard video adaptor that
lets you run any popular software.
volatile memory: Random access
memory (RAM) that stores information
as long as power is supplied to the
computer.
W
warm start: Restarting or resetting a
computer without turning it off.
window: A portion of the screen that
can display its own application,
document or dialog box. Often used to
mean a Microsoft Windows window.
Wireless LAN: Local Area Network
(LAN) through wireless
communication.
write protection: A method for
protecting a diskette (floppy disk) from
accidental erasure.
Glossary-13
GLOSSARY
software: The set of programs,
procedures and related documentation
associated with a computer system.
Specifically refers to computer
programs that direct and control the
computer system’s activities. See also
hardware.
GLOSSARY
Glossary
Glossary-14
Index
Index
C
AC adaptor, See Universal AC adaptor
ASCII characters 5-9
Audio/Video control buttons 1-6, 2-1,
4-16
Cache memory 1-2
CD-RW/DVD-ROM drive 1-4, 1-12
location 2-4
problems 9-10
using 4-5
view 2-14
writing CDs 4-9
Cleaning the computer 4-27
Compact Flash, See Bridge media
Cooling (heat dispersal) 1-9
location of vents 2-2, 2-5
settings 4-28
CPU, See Processor
B
Battery
automatic hibernation 1-9
charging 6-8
extending life 6-11
indicator 2-10, 6-2
location 2-7
monitoring capacity 6-9
real time clock 1-3, 6-4
safety precautions 6-5
save mode 1-9
types 6-3
Battery charger 1-11
Battery pack 1-2, 2-7
additional 1-11, 8-19
replacing 6-12
Bluetooth 1-7
problems 9-24
TOSHIBA Stack, utility 1-11
using 4-24
Boot mode 3-7
Boot priority 7-2
Bridge media
adaptor 1-12
view 2-16
care 8-19
Compact Flash 8-18
inserting/removing 8-13, 14
Memory Stick 8-17
Smart Media 8-15
D
Diskette drive 1-3
using 4-2
view 2-12
Display 1-5, 2-9
automatic power off 1-8
brightness decrease 5-5
brightness increase 5-6
opening 3-6
problems 9-7
selection 5-5
Documentation list 1-2
DVD Video Player 1-10
DVD-ROM drive 1-3, 1-12
location 2-4
problems 9-9
using 4-5
view 2-13
Index-1
INDEX
A
User's manual
INDEX
E
Environment 3-1
Equipment checklist 1-1
Equipment setup
general conditions 3-2
placement 3-2
Ergonomics
lighting 3-4
seating and posture 3-3
work habits 3-4
Expansion memory, See Memory
F
Fn + Ctrl (enhanced keyboard simulation) 5-3
Fn + Enter 5-3
Fn + Esc (sound mute) 5-4
Fn + F1 (instant security) 5-4
Fn + F2 (power save mode) 5-4
Fn + F3 (standby) 5-5
Fn + F4 (hibernation) 5-5
Fn + F5 (display selection) 5-5
Fn + F6 (display brightness) 5-5
Fn + F7 (display brightness) 5-6
Fn + F8 (wireless setting) 5-6
Fn + F9 (Touch Pad) 5-6
Fn + F10 (arrow mode) 5-3
Fn + F11 (numeric mode) 5-3
Fn + F12 (ScrLock) 5-3
Fn-esse 1-10
Function keys 5-2
G
Graphics controller 1-5
H
Hard disk drive 1-3, 1-12
automatic power off 1-8
problems 9-8
Headphone jack, See Sound system
Index-2
Heat dispersal, See Cooling
Hibernation 1-9
automatic 1-8
setting 3-9
Hot keys 1-8
display brightness decrease 5-5
display brightness increase 5-6
display selection 5-5
hibernation 5-5
instant security 5-4
power save mode 5-4
sound mute 5-4
standby 5-5
Touch Pad setting 5-6
wireless setting 5-6
HW Setup 1-10
accessing 7-1
boot priority 7-2
general 7-6
keyboard 7-4
LAN 7-5
password 7-6
window 7-1
I
i.LINK 1-5, 2-6, 8-24
connecting 8-25
disconnecting 8-25
precautions 8-24
problems 9-21
Indicators
keyboard 2-11
system 2-10
Infrared port 1-5
location 2-2
problems 9-16
Instant security, See Hot keys
Interfaces, See Ports
Internet button 1-8, 2-9
Index
K
N
L
Numeric keypad, See Keypad overlay
LAN 1-7
connecting 4-26
disconnecting 4-27
jack 2-6
LAN active indicator 2-5
link indicator 2-5
problems 9-23
LCD, See Display, Video modes and
Monitor external
Level 2 cache, See Cache memory
Line-in jack, See Sound system
Line-out jack, See Sound system
Lock security, See Security lock
O
M
Media care
CD/DVDs 4-19
diskettes 4-19
SD card 8-5
Memory 1-2
Overlay, See Keypad overlay
P
Panel power off, See Power
Password
Key FD 7-8
power on 1-9
problems 9-7
starting the computer by 6-14
supervisor 7-9
user 7-6
PC card 1-6
installing/removing 8-2
location of slot 2-2
problems 9-16
Pointing device, See Touch Pad
Index-3
INDEX
Key FD 7-8
Keyboard 1-5, 5-1
emulating enhanced keyboard 5-2
F1 … F12 function keys 5-2
Fn Sticky key 5-7
hot keys 5-4
problems 9-7
typewriter keys 5-1
Windows special keys 5-7
Keypad overlay 1-9, 5-7
arrow mode 5-7
numeric mode 5-8
temporarily using normal keyboard
(overlay on) 5-8
temporarily using overlay (overlay
off) 5-9
turning on the overlays 5-7
expansion 1-11
installing 8-6
problems 9-19
removing 8-11
Memory Stick, See Bridge media
Microphone jack, See Sound system
Mode Control button 1-6, 2-1
Modem 1-7, 4-20
connecting 4-22
disconnecting 4-23
jack 2-4
problems 9-21
properties menu 4-21
region selection 4-20
Monitor, external 1-5, 2-5, 8-21
problems 9-20
Moving the computer 4-28
INDEX
User's manual
Ports
external monitor 1-5
i.LINK 1-5
infrared 1-5
USB 1-5
Power
button location 2-8
conditions 6-1
indicators 6-3
panel off 1-9, 6-15
problems 9-4
system auto off 6-15
turning off 3-7
hibernation mode 3-8
shut down mode (boot mode) 3-7
standby mode 3-10
turning on 3-6
Power supply 1-9
Power-up modes 6-15
Problems
AC power 9-5
analyzing symptoms 9-2
Battery 9-6
Bluetooth 9-24
CD-RW/DVD-ROM drive 9-10
Diskett e drive 9-15
DVD-ROM drive 9-9
hard disk drive 9-8
hardware and system checklist 9-3
i.LINK 9-21
infrared port 9-16
keyboard 9-7
LAN 9-23
LCD panel 9-7
memory expansion 9-19
modem 9-21
monitor external 9-20
mouse, USB 9-18
overheating power down 9-5
Index-4
password 9-7
PC card 9-16
power 9-4
SD card 9-15
self test 9-4
sound system 9-20
support from TOSHIBA 9-25
system start-up 9-3
Touch Pad 9-17
USB 9-19
Wireless LAN 9-23
Processor 1-2
R
Real time clock battery, See battery
Recovery CD-ROM 3-12
Restarting the computer 3-11
S
SD card 1-6
indicator 2-4
inserting/removing 8-4
location of slot 2-4
problems 9-15
care 8-5
Security lock 1-7, 1-12, 2-2, 8-26
Self test, See Problems
Slim Select Bay modules 1-7
HDD adaptor 2-16, 8-20
location of slot 2-4
using 4-3
SmartMedia, See Bridge media
Soft keys
emulating enhanced keyboard 5-2
Enter 5-3
right Ctrl key 5-3
ScrLock 5-3
Index
T
TOSHIBA Console 1-10
TOSHIBA Console button 1-8, 2-9
TOSHIBA Controls 1-10
TOSHIBA Power Saver 1-10
Touch Pad 1-5
buttons 2-9
location 2-8
problems 9-17
using 4-1
Troubleshooting, See Problems
TV 8-22
TV button 1-6, 2-9
using 8-22
V
Video modes Appendix B
Video RAM 1-2
Video-out jack, See Sound system
Volume control, See Sound system
W
Wireless communication 4-23
indicators 2-2, 4-25
setting by hot keys 5-6
switch 2-2, 4-25
Wireless LAN 1-7
problems 9-23
using 4-23
INDEX
Sound system 1-6
headphone jack 1-6, 2-5
line-in jack 2-5
microphone jack 1-6, 2-5
mute hot keys 5-4
problems 9-20
speakers 2-9
volume control 2-2
Standby 1-10
automatic 1-8
setting 3-10
System indicators, See indicators
U
Universal AC adaptor 1-3
additional 1-11, 8-19
connecting 3-5
DC IN 15V port 2-6
view 2-17
USB 1-5
port location 2-2, 2-5
problems 9-19
Index-5
INDEX
User's manual
Index-6