Canon EOS5DMARKIIBODY Digital Camera User Manual

Xerox Multifunction Devices
Customer Tips
…for the user
dc08cc0440
October 23, 2008
PDL Reference Guide for the
WorkCentre 5222/5225/5230
Accessing Extended Features
Overview
This document applies
to the stated Xerox
products. It is assumed
that your device is
equipped with the
appropriate option(s)
to support the
information within this
document.
This document enables you to access the extended features of the WorkCentre
5222/5225/5230 in environments that do not have a custom print driver.
Note: The commands and syntax used in this document requires familiarity with either
PostScript (PS) or Printer Command Language (PCL).
This document provides the Printer Description Language (PDL) commands and syntax
for each feature. The following items are also included:
•
A PCL table that describes the PCL features the WorkCentre supports and the syntax
to use the feature.
•
A PS table that describes the PS features the WorkCentre supports and the syntax to
use the feature.
This document is not intended to be a complete PS or PCL reference manual. It is a
guide for using the PS and PCL commands with the WorkCentre 5222/5225/5230. Refer
to these sources for additional PS and PCL information:
dc08cc0440
Customer Support
•
PostScript Language Reference Manual, Third Edition, ISBN 0-201-38922-8,
•
PCL5 Printer Language Technical Reference Manual
(http://h20000.www2.hp.com/bc/docs/support/SupportManual/bpl13210/bpl13210.pdf),
•
Printer Job Language Technical Reference Manual
(http://h20000.www2.hp.com/bc/docs/support/SupportManual/bpl13208/bpl13208.pdf), a
Hewlett-Packard manual.
Page 1
Using this Guide
ƒ
Search the Feature Table to determine whether the feature you wish to use is supported.
ƒ
Verify that the feature is supported by the platform. For example, the WorkCentre must have an optional
finisher installed to use stapling commands.
ƒ
Follow across the table to find the syntax listed for the PDL examples shown. Reference the
“Dependencies/Caveats” section when working with PS and/or PCL commands.
PCL
This WorkCentre supports PCL5e and PCL XL emulations that enable the features listed in the following
table.
Feature
Job Name
Custom Paper Size
Media Size
Media Source
Output Location
Stapling
Punch
Booklet
Quantity
Resolution
Bits Per Pixel
Copies
Simplex
Duplex
Orientation
Force Short Edge
Feeding
Job Mode
Job Type
Interleaving Paper
(transparency
separator)
Job Based
Accounting
Auditron
Delayed Print
Banner Sheet
dc08cc0440
Customer Support
Description
The value for Job Name is stored for printing on the banner page.
Customer designated paper size on which to print a job.
The size of media on which to print a job.
Specifies the tray to supply the job’s media.
Indicates the output bin where the completed print job is sent.
Indicates use and location of staple(s).
Indicates use, location, and number of holes to be punched.
This command enables you to print documents as booklets. The pages are
reordered sequentially and are oriented so when folded, the paging is
correct.
Use this command to specify the number of collated sets of a document.
Resolution used to image a job.
This command sets the color depth value.
Use this command to specify the number of uncollated sets of a document
in a print job.
Delivers one-sided output.
Delivers two-sided output.
Delivers output in landscape or portrait orientation.
Rotates orientation of job.
Specifies the Job Mode.
Specifies Confidential Print or Proof Print.
Insert blank media to separate sheets of transparent media.
Allows entry of an accounting code and user ID. To enable this feature the
optional Network Accounting kit is required.
Specify the time to print a job.
Turns on/off the banner sheet that prints at the beginning of every job.
Page 2
PCL/PJL Implementation
The following table contains the PCL feature commands and shows the syntax required to use the feature.
After the table are examples of how to use these commands and examples of a PCL file.
Feature
Job Name
Custom
Paper Size –
available only
for PCL
dc08cc0440
Customer Support
Implementation
@PJL SET JOBNAME =
"jobname-string"
You have to specify by PCL:
<ESC>&l101A
Values
Where jobname-string is a maximum of 32
characters
ƒ Width of Custom Paper is specified by
<ESC>&f#I
where # equals decipoints (88.9 mm –
297.0 mm).
ƒ Length of Custom Paper is specified by
<ESC>&f#J
where # equals decipoints (98.4 mm –
432.0 mm).
For instance:
4.25-inch x 5.5-inch will give
<ESC>&f3060I3960J by
4.25-inch x 720 decipoints/inch = 3060
and
5.5-inch x 720 decipoints/inch = 3960.
Page 3
Feature
Media Size
Implementation
@PJL SET PAPER = value
Values
Where value is one of the following:
A3: A3 (297 x 420mm)
A4: A4 (210 x 297mm)
A5: A5 (180 x 210mm)
JISB4: B4 (257 x 364mm)
JISB5: B5 (182 x 257mm)
STATEMENT: Statement (5.5 x 8.5”) †
EXECUTIVE: Executive (7.25 x 10.5”)
LETTER: Letter (8.5 x 11”)
JISEXEC: 8.5 x 13”
LEGAL: Legal (8.5 x 14”)
LEDGER: Tabloid (11 x 17”)
COM10: No. 10 Envelope (4.1 x 9.5”)
DL: DL Envelope (110 x 220mm)
MONARCH: Monarch Envelope (3.9 x 7.5”)
C5: C5 Envelope (162 x 229mm)
CUSTOM: Custom paper
†: Whether each paper is available depends
on NV memory setting.
The following paper sizes are only available with
bi-pass tray.
A6: A6 (105 x 148mm)
JISB6: B6 (128 x 182mm)
A4COVER: A4 Cover (223 x 297mm)
POSTCARD: Postcard (4 x 6")
50X70: 5 x 7”
8X10: 8 x 10”
SPANISH: 215 x 315mm
LETTERCOVER: 9 x 11”
11X15: 11 x 15”
JPOST: Postcard (100 x 148mm)
JPOSTD: Postcard (148 x 200mm)
TYOUKEI3: Envelope (120 x 235mm)
dc08cc0440
Customer Support
Page 4
Feature
Implementation
<ESC>&l int A
Values
Where int is one of the following:
27: A3 (297 x 420mm)
26: A4 (210 x 297mm)
25: A5 (180 x 210mm)
46: B4 (257 x 364mm)
45: B5 (182 x 257mm)
41: Statement (5.5 x 8.5”) †
1: Executive (7.25 x 10.5”)
2: Letter (8.5 x 11”)
18: 8.5 x 13”
3: Legal (8.5 x 14”)
6: Tabloid (11 x 17”)
81: No. 10 Envelope (4.1 x 9.5”)
90: DL Envelope (110 x 220mm)
80: Monarch Envelope (3.9 x 7.5”)
91: C5 Envelope (162 x 229mm)
101: Custom paper
†: Whether each paper is available depends
on NV memory setting.
Media
Source
dc08cc0440
Customer Support
@PJL SET MEDIASOURCE
= value
The following paper sizes are only available with
bi-pass tray.
24: A6 (105 x 148mm)
44: B6 (128 x 182mm)
200: A4 Cover (223 x 297mm)
216: Postcard (4 x 6")
204: 5 x 7”
208: 8 x 10”
43: 215 x 315mm
201: 9 x 11”
217: 11 x 15”
71: Postcard (100 x 148mm)
72: Postcard (148 x 200mm)
218: Envelope (120 x 235mm)
Where value is one of the following:
TRAY1: Feed from paper tray1
TRAY2: Tray2
TRAY3: Tray3
TRAY4: Tray4
SMH: Tray5 (Bypass)
TRAY6: Tray6
Page 5
Feature
Implementation
Values
<ESC>&l int H
Output
Location
@PJL SET OUTBIN = value
Where int is one of the following:
0: Feed paper from default tray
4: Tray1
1: Tray2
5: Tray3
8: Tray4
7 or 20 = Auto
2 or 3 or 6 = Tray5 (Bypass)
21: Tray6
Where value is one of the following:
UPPER: Center output tray (w/o finisher)
MAINTRAY: Center output tray (w/o
finisher)
CENTERTRAY: Center output tray (w/o
finisher)
MAINTRAY2: Center output tray (w/ BFinisher)
LOWER: Side Tray (facing up) (w/ side tray)
SIDETRAY: Side Tray (facing up) (w/ side
tray)
OUTBIN101: Finisher tray (w/ finisher)
<ESC>&l int G
Where int is one of the following:
0: Automatic Selection
1: Center output tray (w/o finisher)
2: Side Tray (facing up) (w/ side tray)
4: Center output tray (w finisher)
6: Finisher tray (w/ finisher)
Stapling
@PJL SET STAPLE = value
Punch
@PJL
value1
Where value is one of the following:
TOPDUAL
TOPLEFT
TOPRIGHT
BOTTOMDUAL
BOTTOMLEFT
BOTTOMRIGHT
LEFTDUAL
RIGHTDUAL
SADDLE
NONE
Where value1 is one of the following:
TOP
RIGHT
LEFT
BOTTOM
NONE
Where value2 is one of the following:
TWO: 2 holes
THREE: 3 holes
FOUR: 4 holes
SET
PUNCH
@PJL SET JOBATTR
”@PNHN = value2”
dc08cc0440
Customer Support
=
=
Page 6
Feature
Booklet
Implementation
Values
@PJL SET JOBATTR
“@BKLT = value1”
=
Where value1 is one of the following:
NONEDIVIDE: Compile a booklet as long
as the number of sheet does not exceed the
limit
MANUALDIVIDE: Divide sheets based on
the specified limit manually(The number of
sheets is specified with “@BKDN”).
OFF: Do not compile a booklet
@PJL SET JOBATTR
“@BKSG = value2”
=
Where value2 is one of the following:
RIGHT = Right / Bottom Bind
LEFT = Left / Top Bind
@PJL SET JOBATTR
“@BKDN = int1”
=
Where int1 is:
1~9999 = Booklet dividing number for each
set
Quantity
@PJL SET QTY = int
Where int is:
1-999
(If you use this parameter, it also indicate
use collate mode automatically.)
Resolution
@PJL SET RESOLUTION =
value
Where value is one of the following:
600
Bits Per Pixel
@PJL SET BITSPERPIXEL
= value
Where value is one of the following:
1:
1 bit per pixel (per plane)
Copies
@PJL SET COPIES = int
Where int is:
1-999
(This parameter used for uncollated mode.)
<ESC>&l int X
Where int is:
1-999
Simplex
@PJL SET
value1
DUPLEX
=
<ESC>&l int S
Duplex
Orientation
dc08cc0440
Customer Support
@PJL SET
value1
@PJL SET
value2
Where value1 is one of the following:
OFF: simplex
Where int is one of the following:
0: simplex
DUPLEX
=
BINDING
=
Where value1 is one of the following:
ON: duplex
Where value2 is one of the following:
LONGEDGE
SHORTEDGE
(value2 is used combined with value1=ON)
<ESC>&l int S
Where int is one of the following:
1:
Duplex Long Edge Binding
2:
Duplex Short Edge Binding
@PJL SET ORIENTATION
= value
Where value is one of the following:
PORTRAIT
LANDSCAPE
Page 7
Feature
Implementation
Values
<ESC>&l int O
Where int is one of the following:
0:
Portrait
1:
Landscape
2:
Reverse Portrait
3:
Reverse Landscape
Force short
edge feeding
@PJL SET
PAPERDIRECTION = value
Where value is one of the following:
SEF: Short Edge Feed
LEF: Long Edge Feed
Job Mode
@PJL JOB MODE = value
Where value is one of the following:
PRINTER
for Printer
Job Type
@PJL SET HOLD = value1
See Example 3,4
Where value1 is one of the following:
PROOF:
proof print
STORE:
confidential print (secure
print)
The HOLDKEY variable acts as a password
without encryption to protect a held job.
Four-digit string can be any four-digit value
from 0000 to 9999. The default value is "".
When "" (null) is specified, no password is
required.
@PJL
SET
HOLDKEY
="four-digit string"
Interleaving
Paper(Transp
arency
Separator)
@PJL SET SLIPSHEET =
value
Where value is one of the following:OFF:
Job Based
Accounting
Or
Auditron
@PJL SET JOBATTR
"@JOAU = string1"
=
Where string1 is a maximum of 32 characters
(ASCII characters in the range 20h - 7Eh are
allowed Only) as job owner (Capital character
& small character is distinguished)
@PJL SET JOBATTR
"@JOAP = string2"
=
@PJL SET JOBATTR
"@DAID = string3"
=
Where string2 is a maximum of 12 characters
(ASCII characters in the range 20h - 7Eh are
allowed Only) as password without encryption.
It can be null (zero length string)
Where string3 is a maximum of 32 characters
(ASCII characters in the range 20h - 7Eh are
allowed Only) as account ID. It can be null
(zero length string)
Note: Auditron and JBA cannot be used at the
same time. So the same command works for
both modes.
Delay Print
dc08cc0440
Customer Support
@PJL SET JOBATTR =
"@PRTM =
YYYY:MM:DD:hh:mm"
YYYY:MM:DD:hh:mm
YYYY:
year(AD 2000~2099)
MM:
month (1~12)
DD:
day (1~31)
hh:
hour(0~23)
mm:
minute(0~59)
Page 8
Feature
Implementation
Banner Sheet
Values
@PJL SET JOBATTR=
"@BANR=value"
Where value is one of the following:
START:
start sheet
DEVICE:
depend on device setting
OFF:
no banner sheet
@PJL SET JOBATTR=
"@BCMT=comment string"
Where string is a maximum of 255 characters
(ASCII characters in the range 20h - 7Eh are
allowed Only) as comment for banner.
PJL Template
This section illustrates a standard PJL template that is used to access general print features as
well as WorkCentre Product specific features. This template lists each feature and the syntax,
both PCL commands and PJL, required to use these features. The next section of this document
contains other examples of how to use these commands.
Section 1 (Opening Command, Required for all files)
<ESC>%-12345X@PJL JOB MODE=PRINTER
Section 2 (PJL Set Commands)
@PJL SET RESOLUTION=600
@PJL SET COPIES=1
Section 3 (PCL Code used to invoke PCL Language)
@PJL ENTER LANGUAGE=PCL
Section 4 (PCL Data Stream or ASCII Document inserted here for Options such as
selection Different Fonts, Simplex, Duplex, etc.)
,,,,,,,,,,
Section 5 (Closing Command, Required at end of Document)
<ESC>%-12345X@PJL EOJ
Sample PJL Headers
This section contains examples of these commands in use.
Example 1 Simple Print
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL COMMENT Beginning PCL Job<CR><LF>
@PJL SET OUTBIN=MAINTRAY<CR><LF>
@PJL SET QTY=1<CR><LF>
@PJL SET RESOLUTION=600<CR><LF>
@PJL SET JOBATTR="@JOAU=John"<CR><LF>
Example 2 Finishing Options (Stapling)
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET OUTBIN=OUTBIN101<CR><LF>
@PJL SET FINISH=ON<CR><LF>
@PJL SET STAPLE=TOPLEFT<CR><LF>
dc08cc0440
Customer Support
Page 9
Example 3 Finishing Options (Punch)
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET OUTBIN=OUTPIN101<CR><LF>
@PJL SET FINISH=ON<CR><LF>
@PJL SET PUNCH=LEFT<CR><LF>
@PJL SET JOBATTR="@PNHN=TWO"<CR><LF>
Example 4 Finishing Options (Saddle stapling and folding)
It is an example of division in every 5 sheets.
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET OUTBIN=BOOKLETTRAY<CR><LF>
@PJL SET FINISH=ON<CR><LF>
@PJL SET STAPLE=SADDLE<CR><LF>
@PJL SET JOBATTR="@FOLD=BIFOLDMULTIOUTSIDE"<CR><LF>
@PJL SET JOBATTR="@BKLT=MANUALDIVIDE"<CR><LF>
@PJL SET JOBATTR="@BKSG=LEFT"<CR><LF>
@PJL SET JOBATTR="@BKDN=5"<CR><LF>
Example 5 Finishing Options (Bi-Folding(multi page))
It is an example of division in every 5 sheets.
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET OUTBIN=BOOKLETTRAY<CR><LF>
@PJL SET FINISH=NONE<CR><LF>
@PJL SET STAPLE=NONE <CR><LF>
@PJL SET JOBATTR="@FOLD=BIFOLDMULTIOUTSIDE"<CR><LF>
@PJL SET JOBATTR="@BKLT=MANUALDIVIDE"<CR><LF>
@PJL SET JOBATTR="@BKSG=LEFT"<CR><LF>
@PJL SET JOBATTR="@BKDN=5"<CR><LF>
@PJL SET QTY=1<CR><LF>
Example 6 Finishing Options (Bi-Folding(single page))
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET OUTBIN=BOOKLETTRAY<CR><LF>
@PJL SET FINISH=NONE<CR><LF>
@PJL SET STAPLE=NONE <CR><LF>
@PJL SET JOBATTR="@FOLD=BIFOLDINSIDE"<CR><LF>
@PJL SET JOBATTR="@BKSG=LEFT"<CR><LF>
Example 7 Proof Print
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET HOLD=PROOF <CR><LF>
@PJL SET USERNAME="John" <CR><LF>
@PJL SET JOBNAME="Job1" <CR><LF>
dc08cc0440
Customer Support
Page 10
Example 8 Confidential (Secure) Print without encryption
Password: 1234
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET HOLD=STORE <CR><LF>
@PJL SET HOLDKEY="1234"<CR><LF>
@PJL SET USERNAME="John" <CR><LF>
@PJL SET JOBNAME="Job1" <CR><LF>
Example 9 Banner Sheet
banner: start sheet
@PJL SET JOBATTR="@BANR=START"<CR><LF>
@PJL SET JOBATTR="@BCMT=Banner Comment String"<CR><LF>
Example 10 Job Based Accounting & Auditron
userID: Patricia, Password: none, accountID: none
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET JOBATTR="@JOAU=Patricia"<CR><LF>
@PJL SET JOBATTR="@JOAP="<CR><LF>
@PJL SET JOBATTR="@DAID="<CR><LF>
dc08cc0440
Customer Support
Page 11
PCL/PJL Feature Dependencies/Caveats
ƒ
ƒ
All PJL commands must be in the first 2,500 bytes of the job.
To combine printer escape commands (not including PJL commands):
The first two characters after the <esc> MUST be the same.
All alpha characters MUST be lowercase, except the final terminating character.
The commands are read left to right. Combine commands in the order you wish them to
execute.
For example, combine print 5 copies (<ESC>&|5X) and use letter size (<ESC>&|2A) as
<ESC>&|5x2A.
In case of duplicate commands, the last one requested takes precedence.
ƒ
ƒ
The @PJL SET COPIES takes precedence over the PCL Escape Command (<ESC>& | int
X>) to set copies. In general, a PJL command takes precedence over a PCL command.
Valid media sizes for duplexing are between [88.9 x 127] and [297 x 432] (mm) or all sizes
that can be fed from tray1 - 4.
Valid media sizes for stapling include A3, A4, B4, B5, Letter (8.5 x 11”), 8.5 x 13”, Legal (8.5
x 14”), Tabloid (11 x 17”) and Executive (7.25 x 10.5”) for Type A and Type B Finisher. For
Type B Finisher, 8 x 10”, 11 x 15”, A4 Cover, 9 x 11” and 215 x 315mm are also valid.
ƒ
ƒ
ƒ
Valid media sizes for booklet stapling include A3, A4, B4, Letter (8.5 x 11”), 8.5 x 13”, Legal
(8.5 x 14”), Tabloid (11 x 17”) for Type B Finisher.
PCL Fonts
The following PCL fonts are resident.
The commands in the table reference a 12-point font. If you wish to use any other point size,
change the 12v within the PCL Escape Command to the desired size (.25 – 999.75).
The commands listed use the default symbol set, Roman-8. To change the symbol set, you
include the alternate symbol set after the first <ESC> and before the second <ESC>. Use the line
printer examples as a reference.
Font Name
Albertus Medium
Albertus Extra Bold
Antique Olive
Antique Olive Bold
Antique Olive Italic
Arial
Arial Bold
Arial Italic
Arial Bold Italic
CG Times
CG Times Bold
CG Times Italic
CG Times Bold Italic
CG Omega
CG Omega Bold
CG Omega Italic
CG Omega Bold Italic
Clarendon Condensed
Coronet
dc08cc0440
Customer Support
PCL Escape Command
<esc>(<esc>(s1p12v0s1b4362T
<esc>(<esc>(s1p12v0s4b4362T
<esc>(<esc>(s1p12v0s0b4168T
<esc>(<esc>(s1p12v0s3b4168T
<esc>(<esc>(s1p12v1s0b4168T
<esc>(<esc>(s1p12v0s0b16602T
<esc>(<esc>(s1p12v0s3b16602T
<esc>(<esc>(s1p12v1s0b16602T
<esc>(<esc>(s1p12v1s3b16602T
<esc>(<esc>(s1p12v0s0b4101T
<esc>(<esc>(s1p12v0s3b4101T
<esc>(<esc>(s1p12v1s0b4101T
<esc>(<esc>(s1p12v1s3b4101T
<esc>(<esc>(s1p12v0s0b4113T
<esc>(<esc>(s1p12v0s3b4113T
<esc>(<esc>(s1p12v1s0b4113T
<esc>(<esc>(s1p12v1s3b4113T
<esc>(<esc>(s1p12v4s3b4140T
<esc>(<esc>(s1p12v1s0b4116T
Page 12
Font Name
Courier
Courier Bold
Courier Italic
Courier Bold Italic
Garamond Antiqua
Garamond Halbfett
Garamond Kursiv
Garamond Kursiv Halbfett
Line Printer (Roman-8)
Line Printer (Latin-1)
Line Printer (PC-8)
Line Printer (PC-8 D/N)
Line Printer (PC-850)
Line Printer (Legal)
Marigold
Times New
Times New Bold
Times New Italic
Times New Bold Italic
Symbol
Wingdings
Univers Bold
Univers Bold Italic
Univers Bold Condensed
Univers Bold Condensed Italic
Univers Medium
Univers Medium Italic
Univers Medium Condensed
Univers Medium Condensed Italic
Letter Gothic
Letter Gothic Italic
Letter Gothic Bold
Times Roman
Times Italic
Times Bold
Times Bold Italic
Helvetica
Helvetica Oblique
Helvetica Bold
Helvetica Bold Oblique
CourierPS
CourierPS Oblique
CourierPS Bold
CourierPS Bold Oblique
SymbolPS
Palatino Roman
Palatino Italic
Palatino Bold
Palatino Bold Italic
dc08cc0440
Customer Support
PCL Escape Command
<esc>(<esc>(s1p12v0s0b4099T
<esc>(<esc>(s1p12v0s3b4099T
<esc>(<esc>(s1p12v1s0b4099T
<esc>(<esc>(s1p12v1s3b4099T
<esc>(<esc>(s1p12v0s0b4197T
<esc>(<esc>(s1p12v0s3b4197T
<esc>(<esc>(s1p12v1s0b4197T
<esc>(<esc>(s1p12v1s1b4197T
<esc>(8U<esc>(s0p16.67h8.5v0s0b0T
<esc>(0U<esc>(s0p16.67h8.5v0s0b0T
<esc>(10U<esc>(s0p16.67h8.5v0s0b0T
<esc>(11U<esc>(s0p16.67h8.5v0s0b0T
<esc>(12U<esc>(s0p16.67h8.5v0s0b0T
<esc>(1U<esc>(s0p16.67h8.5v0s0b0T
<esc>(<esc>(s1p12v0s0b4297T
<esc>(<esc>(s1p12v0s0b16901T
<esc>(<esc>(s1p12v0s3b16901T
<esc>(<esc>(s1p12v1s0b16901T
<esc>(<esc>(s1p12v1s3b16901T
<esc>(19M<esc>(s1p12v0s0b16686T
<esc>(579L<esc>(s1p12v0s1b31402T
<esc>(<esc>(s1p12v0s3b4148T
<esc>(<esc>(s1p12v1s3b4148T
<esc>(<esc>(s1p12v4s3b4148T
<esc>(<esc>(s1p12v5s3b4148T
<esc>(<esc>(s1p12v0s0b4148T
<esc>(<esc>(s1p12v1s0b4148T
<esc>(<esc>(s1p12v4s0b4148T
<esc>(<esc>(s1p12v5s0b4148T
<esc>(<esc>(s1p12h0s0b4102T
<esc>(<esc>(s1p12h1s0b4102T
<esc>(<esc>(s1p12h0s3b4102T
<esc>(<esc>(s1p12h0s3b4102T
<esc>(<esc>(s1p12h0s3b4102T
<esc>(<esc>(s1p12h0s3b4102T
<esc>(<esc>(s1p12h0s3b4102T
<esc>(<esc>(s1p12v0s0b24580T
<esc>(<esc>(s1p12v1s0b24580T
<esc>(<esc>(s1p12v0s3b24580T
<esc>(<esc>(s1p12v1s3b24580T
<esc>(<esc>(s0p12h0s0b24579T
<esc>(<esc>(s0p12h1s0b24579T
<esc>(<esc>(s0p12h0s3b24579T
<esc>(<esc>(s0p12h1s3b24579T
<esc>(19M<esc>(s1p12v0s0b45358T
<esc>(<esc>(s1p12v0s0b24591T
<esc>(<esc>(s1p12v0s0b24591T
<esc>(<esc>(s1p12v0s0b24591T
<esc>(<esc>(s1p12v0s0b24591T
Page 13
Font Name
ITC Bookman Light
ITC Bookman Light Italic
ITC Bookman Demi
ITC Bookman Demi Italic
Helvetica Narrow
Helvetica Narrow Oblique
Helvetica Narrow Bold
Helvetica Narrow Bold Oblique
New Century Schoolbook Roman
New Century Schoolbook Italic
New Century Schoolbook Bold
New Century Schoolbook Bold Italic
ITC Avant Garde Book
ITC Avant Garde Book Oblique
ITC Avant Garde Demi
ITC Avant Garde Demi Oblique
ITC Zapf Chancery Medium Italic
ITC Zapf Dingbats
dc08cc0440
Customer Support
PCL Escape Command
<esc>(<esc>(s1p12v0s-3b24623T
<esc>(<esc>(s1p12v1s-3b24623T
<esc>(<esc>(s1p12v0s2b24623T
<esc>(<esc>(s1p12v1s2b24623T
<esc>(<esc>(s1p12v4s0b24580T
<esc>(<esc>(s1p12v5s0b24580T
<esc>(<esc>(s1p12v4s3b24580T
<esc>(<esc>(s1p12v5s3b24580T
<esc>(<esc>(s1p12v0s0b24703T
<esc>(<esc>(s1p12v1s0b24703T
<esc>(<esc>(s1p12v0s3b24703T
<esc>(<esc>(s1p12v1s3b24703T
<esc>(<esc>(s1p12v0s0b24607T
<esc>(<esc>(s1p12v1s0b24607T
<esc>(<esc>(s1p12v0s2b24607T
<esc>(<esc>(s1p12v1s2b24607T
<esc>(<esc>(s1p12v1s0b45099T
<esc>(<esc>(s1p12v0s0b45101T
Page 14
PostScript
This WorkCentre supports PS 3 commands that enable the features listed in the following table.
Feature
dc08cc0440
Customer Support
Description
Media Size
This command specifies the size of media on which to
print the job.
Media Direction
This command specifies the edge of the input medium
that will enter the printing engine or imager first and
across which data will be imaged. Values reflect
positions relative to a canonical page in portrait
orientation (width smaller than height):
Media Source
This command specifies the tray to supply the job’s
media.
Media Source from
Bypass tray
This command indicates whether the input medium is to
be fed from bypass tray.
Media Color
Use this command to indicate the color of the media
used to print a job.
Media Weight
Media weight. Unit: (g/㎡) gram per square-meter
Media Class
Paper class (ex. normal, thick, recycled)
Media Type
Media types are used to distinguish the type of media a
job requires.
Media Selection
Specify if you apply the strict setpagedevice rule to
media selection.
Resolution
This command sets the resolution value.
Duplex
Delivers two-sided output. Landscape documents read
like a calendar, and Portrait documents read like a book.
Tumble
Deliver two-sided output. (Use combine with Duplex)
Landscape documents read like a book and Portrait
documents read like a calendar.
Image Enhancement
Specify whether you apply edge-smoothing to output
after rendering
Toner Save
Use this command to control toner consumption when
printing.
Halftone Screen
Selection
This command specifies the screen type.
Output Location
Indicates the output bin where the print job is sent.
Copies
The number of copies to produce, either of each page
individually or of the document as a whole, depending
on the value of the Collate parameter.
Collation
A flag specifying how the output is to be organized when
multiple copies are requested for a multiple-page
document. Output consists of page sets that are
delivered together. If Collate is true, a page set consists
of one copy of all pages of the document; if it is false, a
page set consists of all copies of one page of the
document.
Offset
This feature provides a physical offset of hard copy that
distinguishes between sets or stacks within a job.
Page 15
Feature
Description
Stapling
This command indicates use and location of staple(s).
Punch
This command indicates hole punches for a print job on
a device with hole punch capability.
Booklet
This command enables you to print documents as small
booklets. If available on your printer, you can also have
your job folded or stapled.
Interleaving Paper
(Transparency
Separator)
Insert blank sheet between OHP sheets.
Process Color Model
Select process color model (DeviceGray, DeviceRGB,
DeviceCMYK,,,)
Separations
Specify whether multiple color separations are
generated for each page of output.
Separation Color
Names
Specify the process colorant name.
Separation Order
Specify the order of process colorant name.
Use CIE Color
Specify if you apply CIE-based color space through
color conversion
Job Name
No PostScript command for this feature – use the PJL
set command listed in the “PCL” section.
Job Type(Secure
Print / Proof Print)
Job Based
Accounting
Auditron
Delay Print
Banner Sheet
dc08cc0440
Customer Support
Page 16
PostScript Implementation
The following table contains the PostScript commands and shows the syntax required to use the feature.
Following the table are examples of commands and a PS file.
For more details about PostScript commands, refer to the PostScript Language Reference Manual, Third
Edition, ISBN 0-201-37992-8.
PostScript Print Features/Implementation
In the following table, default values are marked with an asterisk (*).
Feature
Media Size
Implementation
<</PageSize [width height]>>
setpagedevice
Values
[width x height] in 1/72 inch(points)
[842 1191] = A3 (297 x 420mm)
[595 842] = A4 (210 x 297mm)
[420 595] = A5 (180 x 210mm)
[729 1032] = B4 (257 x 364mm)
[516 729] = B5 (182 x 257mm)
[396 612] = Statement (5.5 x 8.5”) †
[522 756] = Executive (7.25 x 10.5”)
[612 792] = Letter (8.5 x 11”)
[612 936] = 8.5 x 13”
[612 1008] = Legal (8.5 x 14”)
[792 1224] = Tabloid (11 x 17”)
[297 684] = No. 10 Envelope (4.1 x 9.5”)
[312 624] = DL Envelope (110 x 220mm)
[279 540] = Monarch Envelope (3.9 x
7.5”)
[459 649] = C5 Envelope (162 x 229mm)
†: Whether each paper is available
depends on NV memory setting.
The following paper sizes are only available
with bi-pass tray.
[297 420] = A6 (105 x 148mm)
[363 516] = B6 (128 x 182mm)
[632 842] = A4 Cover (223 x 297mm)
[288 432] = Postcard (4 x 6")
[360 504] = 5 x 7”
[576 720] = 8 x 10”
[609 892] = 215 x 315mm
[648 792] = 9 x 11”
[792 1080] = 11 x 15”
[283 420] = Postcard (100 x 148mm)
[420 567] = Postcard (148 x 200mm)
[340 666] = Envelope (120 x 235mm)
[649 918] = C4 Envelope (229 x 324mm)
dc08cc0440
Customer Support
Page 17
Feature
Implementation
Values
Media
Direction
<</LeadingEdge int >>
setpagedevice
Where int is one of the following:
0 = Short Edge; top of canonical page
1 = Long Edge; right side of canonical
page
2 = Short Edge; bottom of canonical page
3 = Long Edge; left side of canonical
page
null* = Auto
Media Source
<</MediaPosition int>>
setpagedevice
Where int is one of the following:
0 = Tray1
1 = Tray2
2 = Tray3
3 = Tray4
4 = Tray6
null* = Auto(The values with the asterisk
is the default value)
Media Source
from bypass
tray
<</ManualFeed value>>
setpagedevice
Where value is one of the following:
true = Feed paper from bypass tray
false* = Feed paper from a tray other
than bypass tray
Media Color
<</MediaColor (string) >>
setpagedevice
Where string is one of the following or null*:
white
blue
yellow
green
pink
ivory
gray
buff
goldenrod
red
orange
custom1 = Custom Color 1
custom2 = Custom Color 2
custom3 = Custom Color 3
custom4 = Custom Color 4
custom5 = Custom Color 5
transparent = Clear
other
Media Weight
<</MediaWeight real >>
setpagedevice
Where real is in g/㎡(gram per squaremeter) or null*
(MediaWeight will not affect any tray
selection.)
dc08cc0440
Customer Support
Page 18
Feature
Implementation
Values
Media Class
<</MediaClass (string)>>
setpagedevice
Where string is one of the following or null*:
stationary = Plain
used = Plain Reload
recycled = Recycled
transparency = Transparencies
thin = Lightweight (56-63g/m2)
label = Labels
thick1 = Heavyweight 1 (106-169g/m2)
thick2 = Heavyweight 2 (170-216g/m2)
user1 = Custom 1
user2 = Custom 2
user3 = Custom 3
user4 = Custom 4
user5 = Custom 5
holed = Punched
letterhead = Letterhead
preprinted = Pre-Printed
other = Other
fine thick2 = Bond
envelope = Envelope
Media Type
<</MediaType (string)>>
setpagedevice
Where string is any value or null*.
(MediaType will not affect any tray
selection.)
Media
Selection
<</DeferredMediaSelection
value>>
setpagedevice
Where value is one of the following:
true* = Deferred media selection by
output device (more powerful and flexible
media selection)
false = Immediate media selection by
strict setpagedevice operator
To select the appropriate media when
using MediaClass / Staple / Punch feature,
value must be set to true intentionally in the
beginning of header.
Resolution
<</HWResolution [x y]>>
setpagedevice
Where x and y are one of the following:
600 600*(dpi)
1200 1200
Duplex
<</Duplex value>>
setpagedevice
Where value is one of the following:
true = Duplex
false* = Simplex
Tumble
<</Tumble value>>
setpagedevice
This feature is effective only in conjunction
with that Duplex is true
Where value is one of the following:
true = Tumble (Short edge binding
Duplex)
false* = Duplex (Long edge binding
Duplex)
dc08cc0440
Customer Support
Page 19
Feature
Implementation
Values
Image
Enhancement
<</PostRenderingEnhance true
/PostRenderingEnhanceDetails
<< /Type 32 /REValue int >>
>>
setpagedevice
Where int is one of the following:
0 = No image enhancement
1* = Activate image enhancement
Toner Save
<</PostRenderingEnhance true
/PostRenderingEnhanceDetails
<< /Type 32 /TonerSaver int >>
>>
setpagedevice
Where int is one of the following:
0* = No toner saving
1 = Lighten output density, toner saving
Halftone
Screen
Selection
<</PostRenderingEnhance true
/PostRenderingEnhanceDetails
<< /Type 32 /EngineScreen int >>
>>
setpagedevice
Where int is one of the following:
0 = Low frequency screen
1* = High frequency screen
2 = Compatible screen with FX standard
PDL’s(Low frequency)
3 = Compatible screen with FX standard
PDL’s(High frequency)
Output
Location
<</OutputType (string)>>
setpagedevice
Where string is one of the following or null*:
CENTER TRAY1: Center output tray (w/o
finisher)
CENTER TRAY2: Center output tray (w/
finisher type SB)
SIDE TRAY: Side Tray (facing up) (w/
side tray)
FINISHER TRAY: Finisher tray (w/
finisher)
BOOKLET TRAY: Finisher tray (w/
booklet)
Null* = Not specified
Quantity
<</NumCopies value >>
setpagedevice
Where value is one of the following:
integer from 1 to 9999 : number of copies
null*: Not specified
Collation
<</Collate value >>
setpagedevice
Where value is one of the following:
true = collated
false* = uncollated
Offset
<</Jog int >>setpagedevice
Where int is one of the following:
0* = Do not offset
3 = Offset at the beginning of each page
[set]
dc08cc0440
Customer Support
Page 20
Feature
Implementation
Stapling
(w/ finisher)
<</Staple int1
/StapleDetails << /Type 7
/Location int2 >>
>>
setpagedevice
Where int1 is one of the following:
0* = Do not staple
3 = Staple at the end of each set
Where int2 is one of the following:
0* = top-left-single
1 = bottom-left-single
2 = top-right-single
3 = bottom-right-single
4 = top-double
5 = bottom-double
6 = left-double
7 = right-double
Punch
(w/ fnisher)
<</Punch int1
/PunchDetails << /Type 5
/Position int2
/Numholes int3 >>
>>
setpagedevice
Where int1 is one of the following:
0* = Do not punch
3 = Do punch by set unit.
Where int2 is one of the following:
0 = topside
1 = bottom side
2 = left side
3 = right side
Where int3 is one of the following:
2 = 2 holes
3 = 3 holes
4 = 4 holes
Booklet
(w/ finisher
and booklet
module)
<</Booklet value1
/BookletDetails << /Type 3
/StapleType int
/PrintInside value2
/PageSet value3>>
>>
setpagedevice
Where value1 is one of the following:
true = Do Booklet.
false* = Do not Booklet.
Where int is one of the following:
0* = Do not file on inside.
1 = File on inside.
Where value2 is one of the following:
true* = Print on inside.
false = Print on outside.
This feature is effective only in conjunction
with that StapleType is 0.
Where value3 is one of the following:
true = Integrate several page and folds.
false = Fold every page.
This feature is effective only in conjunction
with that StapleType is 0.
dc08cc0440
Customer Support
Values
Page 21
Feature
Interleaving
Paper
(Transparency
Separator)
Implementation
<</SlipSheet int1
/SlipSheetDetails << /Type 1
/AutoTraySelect int2
/SheetTray int3
/MediaClass (string) >>
>>
setpagedevice
Values
Where int1 is one of the following:
0* = Do not deliver interleaving paper.
4 = Deliver interleaving paper at the end
of each page
Where int2 is one of the following:
0 = SheetTray is referred and feed
interleaving paper from the SheetTray
1* = Feed interleaving paper from a tray
following system setting. SheetTray is not
referred.
Where int3 is one of the following:
0* = Feed interleaving paper from Tray1
1 = Tray2
2 = Tray3
3 = Tray4
4 = Tray6
100 = Tray5 (Bypass)
Where string is same as the “Media Class”
feature. It means media class for the
interleaving paper.
Process Color
Model
<</ProcessColorModel name >>
setpagedevice
Where name is one of the following:
/DeviceGray
/DeviceRGB (with Separations true)
/DeviceCMYK (with Separations true)
/DeviceCMY (with Separations true)
/DeviceRGBK (with Separations true)
Separations
<</Separations value >>
setpagedevice
Where value is one of the following:
true = Multiple color separations will be
generated for each page of output.
false* = All colorants will be combined into
a single composite page on a single sheet
of physical medium.
Separation
Color Names
<</SeparationColorNames
value>>
setpagedevice
Where value is an array.
Legal element values are the process
colorant names implied by the process
color model.
Valid colorant names for each process
color model are like the following in case of
separation
DeviceCMYK = Cyan, Magenta, Yellow,
Black
DeviceCMY = Cyan, Magenta, Yellow
DeviceRGB = Red, Green, Blue
DeviceRGBK = Red, Green, Blue, Gray
DeviceGray = Gray
dc08cc0440
Customer Support
Page 22
Feature
Implementation
Values
Separation
Order
<</SeparationOrder value>>
setpagedevice
Where value is an array.
Legal element values are the process
colorant names implied by the process color
model.
Use CIE Color
<</UseCIEColor value>>
setpagedevice
Where value is one of the following:
true = Re-map each color from device
color space to device independent’s CIEbased color space
false* = Do not re-map color
dc08cc0440
Customer Support
Page 23
Sample PostScript Headers
Example 1 Header for Simple Print
%!PS
Example 2 Header for Finishing
(Letter paper, duplex, 10 copies with collation, stapling with left-upper single and finisher tray for
output bin)
%!PS
<< /DeferredMediaSelection true >> setpagedevice
<</PageSize [612 792]>>setpagedevice
<</Duplex true /Tumble false>>setpagedevice
<</OutputType (FINISHER TRAY)>>setpagedevice
<</Collate true>>setpagedevice
<</NumCopies 10>>setpagedevice
<</Staple 3 /StapleDetails << /Type 7 /Location 0 >> >>setpagedevice
PostScript Feature Dependencies/Caveats
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
dc08cc0440
Customer Support
All DSC (Document Structure Convention) comments are ignored and not interpreted.
Valid media sizes for duplexing are between [253 x 360] and [841 x 1224] (point) or all sizes that
can be fed from tray1 - 4.
Valid media sizes for stapling include A3, A4, B4, B5, Letter (8.5 x 11”), 8.5 x 13”, Legal (8.5 x
14”), Tabloid (11 x 17”) and Executive (7.25 x 10.5”) for Type A and Type B Finisher. For Type B
Finisher, 8 x 10”, 11 x 15”, A4 Cover, 9 x 11” and 215 x 315mm are also valid.
Valid media sizes for booklet stapling include A3, A4, B4, Letter (8.5 x 11”), 8.5 x 13”, Legal (8.5 x
14”), Tabloid (11 x 17”) for Type B Finisher.
Valid media classes for duplex are stationary, recycled, thin, holed, letterhead, preprinted, other
and user1-5 paper.
Valid media classes for staple are stationary, used, recycled, thin, thick1, thick2, holed,
letterhead, preprinted, other, fine thick2 and user1-5 paper for Type A and Type B Finisher.
Valid media classes for booklet staple are stationary, recycled, letterhead, preprinted, other and
user1-5 paper for Type B Finisher.
Page 24
PostScript Fonts
The following PostScript fonts are resident with Adobe interpreter.
Font Name
Albertus
Albertus Italic
Albertus Light
Antique Olive Roman
Antique Olive Italic
Antique Olive Bold
Antique Olive Compact
Apple Chancery
Arial
Arial Italic
Arial Bold
Arial Bold Italic
ITC Avant Garde Gothic Book
ITC Avant Garde Gothic Book Oblique
ITC Avant Garde Gothic Demi
ITC Avant Garde Gothic Demi Oblique
Bodoni Roman
Bodoni Italic
Bodoni Bold
Bodoni Bold Italic
Bodoni Poster
Bodoni Poster Compressed
ITC Bookman Light
ITC Bookman Light Italic
ITC Bookman Demi
ITC Bookman Demi Italic
Carta
Chicago
Clarendon Roman
Clarendon Bold
Clarendon Light
Cooper Black
Cooper Black Italic
Copperplate Gothic 32BC
Copperplate Gothic 33BC
Coronet
Courier
Courier Oblique
Courier Bold
Courier Bold Oblique
Eurostile Medium
Eurostile Bold
Eurostile Extended No. 2
Eurostile Bold Extended No. 2
Geneva
dc08cc0440
Customer Support
PostScript Font Name
/AlbertusMT
/AlbertusMT-Italic
/AlbertusMT-Light
/AntiqueOlive-Roman
/AntiqueOlive-Italic
/AntiqueOlive-Bold
/AntiqueOlive-Compact
/Apple-Chancery
/ArialMT
/Arial-ItalicMT
/Arial-BoldMT
/Arial-BoldItalicMT
/AvantGarde-Book
/AvantGarde-BookOblique
/AvantGarde-Demi
/AvantGarde-DemiOblique
/Bodoni
/Bodoni-Italic
/Bodoni-Bold
/Bodoni-BoldItalic
/Bodoni-Poster
/Bodoni-PosterCompressed
/Bookman-Light
/Bookman-LightItalic
/Bookman-Demi
/Bookman-DemiItalic
/Carta
/Chicago
/Clarendon
/Clarendon-Bold
/Clarendon-Light
/CooperBlack
/CooperBlack-Italic
/Copperplate-ThirtyTwoBC
/Copperplate-ThirtyThreeBC
/Coronet-Regular
/Courier
/Courier-Oblique
/Courier-Bold
/Courier-BoldOblique
/Eurostile
/Eurostile-Bold
/Eurostile-ExtendedTwo
/Eurostile-BoldExtendedTwo
/Geneva
Page 25
Font Name
Gill Sans
Gill Sans Italic
Gill Sans Bold
Gill Sans Bold Italic
Gill Sans Light
Gill Sans Light Italic
Gill Sans Extra Bold
Gill Sans Condensed
Gill Sans Condensed Bold
Goudy Oldstyle
Goudy Oldstyle Italic
Goudy Bold
Goudy Bold Italic
Goudy Extra Bold
Helvetica
Helvetica Oblique
Helvetica Bold
Helvetica Bold Oblique
Helvetica Narrow
Helvetica Narrow Oblique
Helvetica Narrow Bold
Helvetica Narrow Bold Oblique
Helvetica Condensed
Helvetica Condensed Oblique
Helvetica Condensed Bold
Helvetica Condensed Bold Oblique
Hoefler Text
Hoefler Text Italic
Hoefler Text Black
Hoefler Text Black Italic
Hoefler Ornaments
Joanna
Joanna Italic
Joanna Bold
Joanna Bold Italic
Letter Gothic
Letter Gothic Slanted
Letter Gothic Bold
Letter Gothic Bold Slanted
ITC Lubalin Graph Book
ITC Lubalin Graph Book Oblique
ITC Lubalin Graph Demi
ITC Lubalin Graph Demi Oblique
Marigold
Monaco
ITC Mona Lisa Recut
New Century Schoolbook Roman
New Century Schoolbook Italic
dc08cc0440
Customer Support
PostScript Font Name
/GillSans
/GillSans-Italic
/GillSans-Bold
/GillSans-BoldItalic
/GillSans-Light
/GillSans-LightItalic
/GillSans-ExtraBold
/GillSans-Condensed
/GillSans-BoldCondensed
/Goudy
/Goudy-Italic
/Goudy-Bold
/Goudy-BoldItalic
/Goudy-ExtraBold
/Helvetica
/Helvetica-Oblique
/Helvetica-Bold
/Helvetica-BoldOblique
/Helvetica-Narrow
/Helvetica-Narrow-Oblique
/Helvetica-Narrow-Bold
/Helvetica-Narrow-BoldOblique
/Helvetica-Condensed
/Helvetica-Condensed-Oblique
/Helvetica-Condensed-Bold
/Helvetica-Condensed-BoldObl
/HoeflerText-Regular
/HoeflerText-Italic
/HoeflerText-Black
/HoeflerText-BlackItalic
/HoeflerText-Ornaments
/JoannaMT
/JoannaMT-Italic
/JoannaMT-Bold
/JoannaMT-BoldItalic
/LetterGothic
/LetterGothic-Slanted
/LetterGothic-Bold
/LetterGothic-BoldSlanted
/LubalinGraph-Book
/LubalinGraph-BookOblique
/LubalinGraph-Demi
/LubalinGraph-DemiOblique
/Marigold
/Monaco
/MonaLisa-Recut
/NewCenturySchlbk-Roman
/NewCenturySchlbk-Italic
Page 26
Font Name
New Century Schoolbook Bold
New Century Schoolbook Bold Italic
NewYork
OCR-B Letterpress M
Optima Roman
Optima Italic
Optima Bold
Optima Bold Italic
Oxford
Palatino Roman
Palatino Italic
Palatino Bold
Palatino Bold Italic
Stempel Garamond Roman
Stempel Garamond Italic
Stempel Garamond Bold
Stempel Garamond Bold Italic
Symbol
Tekton Regular
Times Roman
Times Italic
Times Bold
Times Bold Italic
Times New Roman
Times New Roman Italic
Times New Roman Bold
Times New Roman Bold Italic
Univers 45 Light
Univers 45 Light Oblique
Univers 55
Univers 55 Oblique
Univers 65 Bold
Univers 65 Bold Oblique
Univers 57 Condensed
Univers 57 Condensed Oblique
Univers 67 Condensed Bold
Univers 67 Condensed Bold Oblique
Univers 53 Extended
Univers 53 Extended Oblique
Univers 63 Extended Bold
Univers 63 Extended Bold Oblique
Wingdings
ITC Zapf Chancery Medium Italic
ITC Zapf Dingbat
dc08cc0440
Customer Support
PostScript Font Name
/NewCenturySchlbk-Bold
/NewCenturySchlbk-BoldItalic
/NewYork
/OCRBLetM
/Optima
/Optima-Italic
/Optima-Bold
/Optima-BoldItalic
/Oxford
/Palatino-Roman
/Palatino-Italic
/Palatino-Bold
/Palatino-BoldItalic
/StempelGaramond-Roman
/StempelGaramond-Italic
/StempelGaramond-Bold
/StempelGaramond-BoldItalic
/Symbol
/Tekton
/Times-Roman
/Times-Italic
/Times-Bold
/Times-BoldItalic
/TimesNewRomanPSMT
/TimesNewRomanPS-ItalicMT
/TimesNewRomanPS-BoldMT
/TimesNewRomanPS-BoldItalicMT
/Univers-Light
/Univers-LightOblique
/Univers
/Univers-Oblique
/Univers-Bold
/Univers-BoldOblique
/Univers-Condensed
/Univers-CondensedOblique
/Univers-CondensedBold
/Univers-CondensedBoldOblique
/Univers-Extended
/Univers-ExtendedObl
/Univers-BoldExt
/Univers-BoldExtObl
/Wingdings-Regular
/ZapfChancery-MediumItalic
/ZapfDingbats
Page 27
Additional Information
Xerox Customer Support welcomes feedback on all documentation - send feedback via e-mail to:
USA.DSSC.Doc.Feedback@mc.usa.xerox.com.
You can reach Xerox Customer Support at 1-800-821-2797 (USA),
TTY 1-800-855-2880 or at http://www.xerox.com.
Other Tips about Xerox multifunction devices are available at the following URL:
http://www.office.xerox.com/support/dctips/dctips.html.
XEROX® and the sphere of connectivity design, and WorkCentre® are trademarks of Xerox Corporation in the United
States and/or other countries.
© 2008 Xerox Corporation. All rights reserved.
dc08cc0440
Customer Support
Page 28
Download PDF

advertising