Canon | FAX-L220 | User`s guide | Canon H12251 Fax Machine User Manual

Canon
FAX-L220/L295
User’s Guide
IMPORTANT!
• If you have purchased the FAXL295 model, be sure to read
Appendix B before reading the rest of this guide.
This equipment conforms with the essential requirements of EC
Directive 1999/5/EC.
We declare that this product conforms with the EMC requirements
of EC Directive 1999/5/EC at nominal mains input 230V, 50Hz
although the rated input of the product is 200240V, 50/60Hz.
If you move to another EU country and are experiencing trouble
please call the Canon Help Desk.
(For Europe Only)
Model Name
• H12251 (FAXL220)
• H12250 (FAXL295)
Copyright
Copyright © 2003 by Canon, Inc. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into
any language or computer language in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual, or otherwise, without the prior
written permission of Canon, Inc.
Trademarks
Canon is a registered trademark, and UHQ is a trademark of Canon Inc.
All other product and brand names are registered trademarks, trademarks or service
marks of their respective owners.
As an ENERGY STAR® Partner, Canon has determined that
the FAXL295/L220 meets the ENERGY STAR® guidelines
for energy efficiency.
ii
Preface
Super G3 is a phrase used to describe the new generation of
fax units that use ITUT V.34 standard 33.6 Kbps* modems.
Super G3 High Speed Fax units allow transmission time of
approximately three seconds* per page which results in
reduced telephone line charges.
* Approximately three seconds per page document transmission time based on Canon FAX
Standard Chart No. 1 (Standard Mode) at 33.6 Kbps modem speed. The Public Switched
Telephone Network (PSTN) currently supports 28.8 Kbps modem speeds or lower, depending
on telephone line conditions.
Laser Safety Information
Laser radiation could be hazardous to the human body. For this reason, laser radiation
emitted inside this unit is hermetically sealed within the protective housing and
external cover. No radiation can leak from the machine in the normal operation of the
product by the user.
This fax is classified as a Class 1 Laser Product under IEC 608251: 1993, EN
608251: 1994.
■ 200240 V model
The label shown below is attached to the laser scan unit on the fax.
This fax has been classified under IEC 608251: 1993, EN608251: 1994 and
conforms to the following classes:
CLASS 1 LASER PRODUCT
LASER KLASSE 1
APPAREIL A RAYONNEMENT LASER DE CLASSE 1
APPARECCHIO LASER DI CLASSE 1
PRODUCTO LASER DE CLASE 1
APARELHO A LASER DE CLASSE 1
Performance of procedures other than those specified in this guide may result in
hazardous radiation exposure.
Preface
iii
Contents
Chapter 1: Introduction
Type Conventions Used in This Guide.............................................................
Customer Support .............................................................................................
Important Safety Instructions............................................................................
12
13
14
Chapter 2: Setting Up
Unpacking the FAX ..........................................................................................
Removing Shipping Materials.....................................................................
Assembling the FAX ........................................................................................
Making Connections .........................................................................................
Connecting the Telephone Line Cord and External Devices ......................
Connecting the Power Cord ........................................................................
Setting the Language and Country....................................................................
Main Components of the FAX..........................................................................
Operation Panel ...........................................................................................
Special Function Buttons.......................................................................
Installing the Toner Cartridge...........................................................................
Loading Paper ...................................................................................................
Testing the FAX................................................................................................
22
23
24
25
25
27
28
210
211
211
212
215
216
Chapter 3: Registering Information
Guidelines for Entering Numbers, Letters, and Symbols .................................
Correcting a Mistake ...................................................................................
Registering Sender Information........................................................................
What is Sender Information? ......................................................................
Entering the Date and Time ........................................................................
Registering Your FAX Number and Name.................................................
Setting the Telephone Line Type......................................................................
Dialling Through a Switchboard.......................................................................
Registering the R Button .............................................................................
Setting the Summer Time .................................................................................
32
34
35
35
36
36
38
39
39
311
Chapter 4: Document Handling
Document Requirements...................................................................................
Scanned Area of a Document......................................................................
Loading Documents..........................................................................................
Adding Pages to the Document in the ADF................................................
42
42
43
44
iv
Preface
Chapter 5: Paper Handling
Paper Requirements ..........................................................................................
Printable Area..............................................................................................
Selecting Paper for Your FAX..........................................................................
Loading Paper ...................................................................................................
Selecting FaceUp or FaceDown Paper Delivery ............................................
Changing the Paper Size Setting .......................................................................
Adjusting the Toner Saver Setting ....................................................................
52
53
53
53
54
56
58
Chapter 6: Speed Dialling
What is Speed Dialling?....................................................................................
Speed Dialling Methods ..............................................................................
Registering OneTouch Speed Dialling ............................................................
Registering Coded Speed Dialling....................................................................
Registering Group Dialling ...............................................................................
Using Speed Dialling ........................................................................................
Sending a Document With Speed Dialling..................................................
Making a Telephone Call With Speed Dialling ..........................................
Dialling with the Directory ...............................................................................
Printing Speed Dialling Lists ............................................................................
62
62
63
67
611
614
614
615
616
617
Chapter 7: Sending Faxes
Preparing to Send a Fax ....................................................................................
Documents You Can Fax ............................................................................
Setting the Scanning Resolution..................................................................
Setting the Scanning Contrast .....................................................................
Dialling Methods .........................................................................................
Sending Methods...............................................................................................
Memory Sending .........................................................................................
Manual Sending Via the Handset ................................................................
Cancelling Sending ...........................................................................................
Redialling When the Line is Busy ....................................................................
Manual Redialling .......................................................................................
Cancelling Manual Redialling ...............................................................
Automatic Redialling ..................................................................................
What is Automatic Redialling?..............................................................
Cancelling Automatic Redialling ..........................................................
Setting the Options for Automatic Redialling .......................................
Sending the Same Document to Several Fax Numbers
(Sequential Broadcasting) ..............................................................................
Delayed Sending ...............................................................................................
Scanning a Document into Memory for Delayed Sending..........................
Printing a Document Set for Delayed Sending ...........................................
Deleting a Document Set for Delayed Sending...........................................
Preface
72
72
72
73
74
75
75
76
78
79
79
79
79
79
79
710
712
714
714
716
717
v
Chapter 8: Receiving Faxes
Receiving Methods ...........................................................................................
82
Receiving Faxes Automatically: FAX ONLY MODE ...............................
82
Setting FAX ONLY MODE..................................................................
82
Receiving Both Faxes and Telephone Calls Automatically: Fax/Tel Mode 84
Setting Fax/Tel Mode ............................................................................
84
Setting the Options for Fax/Tel Mode...................................................
85
Receiving Faxes Manually: MANUAL MODE .........................................
87
Setting MANUAL MODE ....................................................................
87
Receiving a Fax Manually.....................................................................
87
Receiving With an Answering Machine: ANS.MACHINE MODE...........
89
Setting ANS.MACHINE MODE ..........................................................
89
Using the FAX With an Answering Machine .......................................
89
Receiving While Performing Other Tasks........................................................ 810
Receiving Faxes in Memory When a Problem Occurs..................................... 810
Cancelling Receiving........................................................................................ 811
Chapter 9: Special Features
Special Dialling.................................................................................................
Entering Pauses in a Fax/Telephone Number .............................................
Switching Temporarily to Tone Dialling ....................................................
Dialling Through a Switchboard .................................................................
Documents Stored in Memory..........................................................................
Printing a List of Documents Stored in Memory ........................................
Printing a Document Stored in Memory .....................................................
Sending a Document Stored in Memory .....................................................
Deleting a Document Stored in Memory ....................................................
Polling...............................................................................................................
What is Polling? ..........................................................................................
Polling Receiving ........................................................................................
Polling Another Fax Machine ...............................................................
Cancelling Polling Receiving ................................................................
Polling Sending ...........................................................................................
Setting Up the Polling Box....................................................................
Scanning a Document into the Polling Box ..........................................
Changing or Deleting the Polling Box Settings ....................................
Restricting Use of Your FAX ...........................................................................
Enabling Restriction of Your FAX .............................................................
Cancelling Restriction of Your FAX ..........................................................
Restricting Reception........................................................................................
vi
92
92
93
93
94
94
95
96
98
99
99
99
99
911
911
911
914
914
916
916
917
919
Preface
Chapter 10: Copying
Documents You Can Copy ...............................................................................
Making Copies ..................................................................................................
Making a Quick Single Copy............................................................................
102
102
103
Chapter 11: Reports and Lists
Summary of Reports and Lists..........................................................................
ACTIVITY REPORT .......................................................................................
TX (Transmission) REPORT............................................................................
MULTI TX/RX (Transaction) REPORT ....................................................
RX (Reception) REPORT .................................................................................
112
113
114
115
115
Chapter 12: Maintenance
Periodic Cleaning..............................................................................................
Cleaning the FAX’s Exterior.......................................................................
Cleaning the FAX’s Interior........................................................................
Cleaning the Scanner Components..............................................................
Replacing the Toner Cartridge ..........................................................................
122
122
123
124
126
Chapter 13: Troubleshooting
Clearing Jams ....................................................................................................
Jams in the ADF ..........................................................................................
Paper Jams ...................................................................................................
Jams in the Paper Delivery Slots ...........................................................
Jams Inside the Unit...............................................................................
LCD Messages ..................................................................................................
Paper Feeding Problems....................................................................................
Faxing Problems ...............................................................................................
Sending Problems........................................................................................
Receiving Problems.....................................................................................
Copying Problems.............................................................................................
Telephone Problems..........................................................................................
Printing Problems..............................................................................................
General Problems..............................................................................................
If You Cannot Solve a Problem ........................................................................
If a Power Cut Occurs .......................................................................................
132
132
133
133
133
138
1313
1313
1313
1315
1317
1318
1318
1320
1321
1322
Preface
vii
Chapter 14: Summary of Settings
Understanding the Menu System...................................................................... 142
Printing a List to Check the Current Settings.............................................. 142
Accessing the Menus................................................................................... 143
USER SETTINGS Menu .................................................................................. 144
REPORT SETTINGS Menu............................................................................. 145
TX (Transmission) SETTINGS Menu.............................................................. 146
RX (Reception) SETTINGS Menu................................................................... 147
PRINTER SETTINGS Menu............................................................................ 148
POLLING BOX Menu...................................................................................... 149
SYSTEM SETTINGS Menu ............................................................................ 1410
Appendix A: Specifications
General Specifications ......................................................................................
Facsimile...........................................................................................................
Copier................................................................................................................
Telephone..........................................................................................................
Printer................................................................................................................
A2
A2
A3
A3
A3
Appendix B: FAXL295 Instructions
Introduction.......................................................................................................
Differences Between the FAXL295 and FAXL220.......................................
Using Your Documentation ..............................................................................
Unpacking the FAXL295 ................................................................................
Connecting the FAXL295 to Your PC ............................................................
Print Media Requirements ................................................................................
Printable Area..............................................................................................
Selecting Print Media........................................................................................
Loading Envelopes ...........................................................................................
Loading Transparencies....................................................................................
B2
B2
B2
B2
B3
B4
B4
B5
B5
B7
Appendix C: Options
Optional Handset ..............................................................................................
Package Contents ........................................................................................
Attaching the Handset to Your FAX...........................................................
Maintaining Your Handset ..........................................................................
C2
C2
C3
C4
Index .......................................................................................................................................
I1
viii
Preface
Chapter 1
❏
Type Conventions Used in This Guide ......................................................
12
❏
Customer Support ......................................................................................
13
❏
Important Safety Instructions.....................................................................
14
Introduction
11
Introduction
Chapter 1
Introduction
Type Conventions Used in This Guide
Please read the list below of symbols, terms, and abbreviations used in this guide.
Cautions tell you how to avoid actions that could injure you or damage your FAX. In
order to use your unit safely, always observe these cautions.
Notes provide advice on using your FAX more effectively, describe operating restrictions,
and tell you how to avoid minor difficulties. Reading these is recommended to make the
most of your unit and its functions.
(
p. nnn)
default
12
A number preceded by an arrow and enclosed in parenthesis references
a page number (p.) or page numbers (pp.) that contain more
information on the topic of the previous sentence.
A setting that remains in effect unless you change it.
document or fax
The original sheet(s) of paper you send or receive with your FAX.
menu
A list of settings from which you select an item to set up or change. A
menu has a title which appears in the LCD.
TX/RX NO.
Transaction number. When you send or receive a document, your FAX
automatically assigns the document a unique transaction number. A
transaction number is a fourdigit number that will help you keep track
of documents you send and receive.
TX
Denotes Sending.
RX
Denotes Receiving.
Ex:
Example of a message or setting displayed in the LCD.
ADF
Automatic Document Feeder. The device on your FAX that
automatically feeds a document into the unit for faxing and copying.
LCD
Liquid Crystal Display. The display on the operation panel that
displays messages and settings.
ECM
Error Correction Mode. The ability of your FAX to reduce system and
line errors when sending to or receiving from a fax machine with ECM
capability.
G3
Group 3. A system that uses encoding schemes to transmit image data
while reducing the amount of data that needs to be transmitted, thus
reducing transmission time.
ITUTS
International Telecommunications UnionTelecommunications Sector.
A committee created to set international standards for
telecommunications.
Introduction
Chapter 1
Customer Support
Your FAX is designed with the latest technology to provide troublefree operation. If
you encounter a problem with the unit’s operation, try to solve it by using the
information in Chapter 13. If you cannot solve the problem or if you think your FAX
needs servicing, contact your local authorised Canon dealer or the Canon help line.
Chapter 1
Introduction
13
Introduction
In addition, this guide uses distinctive typefaces to identify buttons and information
in the LCD:
• The buttons you press appear in this typeface: Stop.
• Information in the LCD appears in this typeface: USER SETTINGS.
Important Safety Instructions
Read these safety instructions thoroughly before using your FAX.
Except as specifically described in this guide, do not attempt to service the FAX
yourself. Never attempt to disassemble the unit: opening and removing its interior
covers will expose you to dangerous voltages and other risks. For all service, contact
your local authorised Canon dealer or the Canon help line.
■ Handling and Maintenance
14
•
Follow all warnings and instructions marked on the FAX.
•
Do not subject the FAX to strong physical shocks or vibrations.
•
Always unplug the FAX before moving or cleaning it.
•
To avoid paper jams, never unplug the power cord, open the front cover, or add
or remove paper in the multipurpose tray while printing.
•
When transporting the FAX, be sure to remove the toner cartridge from the unit.
Place the toner cartridge in its original protective bag or wrap it in a thick cloth
to prevent exposure to light.
•
Always lift the FAX as shown below. Never lift it by any of its attachments.
•
Do not insert any objects into the slots or openings on the FAX since they may
touch dangerous voltage points or short out parts. This could result in fire or
electric shock.
•
Do not allow small objects (such as pins, paper clips, or staples) to fall into the
FAX. If something does fall into it, unplug the unit immediately and contact your
local authorised Canon dealer or the Canon help line.
•
To avoid spillage in or around the unit, do not eat or drink near it. If you spill
liquid or if any substance falls into it, unplug the unit immediately and contact
your local authorised Canon dealer or the Canon help line.
•
Keep the FAX clean. Dust accumulation can prevent the unit from operating
properly.
Introduction
Chapter 1
Unplug the FAX from the wall outlet and contact your local authorised Canon
dealer or the Canon help line in any of the following cases:
– When the power cord or plug is damaged or frayed.
– If liquid has spilled into the unit.
– If the unit has been exposed to rain or water.
– If the unit does not operate normally when you have followed the instructions
in this guide. Adjust only those controls that are covered by the instructions in
this guide. Improper adjustment of other controls may result in damage and
may require extensive work by a qualified technician to restore the product to
normal operation.
– If the unit has been dropped or the cabinet has been damaged.
– If the unit exhibits a distinct change in performance, indicating a need for
servicing.
■ Location
Chapter 1
•
Place the FAX on a flat, stable, vibrationfree surface that is strong enough to
support its weight (approx. 10 kg).
•
Place the FAX in a cool, dry, clean, well ventilated place.
– Make sure the area is free from dust.
– Make sure the location is not affected by extreme temperature changes, and
always stays between 10°C and 32.5°C.
– Make sure the area’s relative humidity is always between 20% and 80%.
•
Keep the FAX away from direct sunlight as this can damage it. If you have to
place it near a window, install heavy curtains or blinds.
•
Do not use the FAX near water. Make sure that no wet or humid objects come
into contact with the unit.
•
Do not use or store the FAX outdoors.
•
Do not install the FAX near devices that contain magnets or generate magnetic
fields, such as speakers.
•
If possible, place the FAX near an existing telephone line outlet for easy
connection of the telephone line cord, and to avoid the expense of installing a
new outlet.
•
Place the FAX near a standard 200240 V AC (5060 Hz) power outlet.
•
To ensure reliable operation of the FAX and to protect it from overheating
(which can cause it to operate abnormally and create a fire risk), do not block the
exhaust vent. Never block or cover any openings on the unit by placing it on a
bed, sofa, rug, or other similar surface. Do not place the unit in a cupboard or
builtin installation, or near a radiator or other heat source unless proper
ventilation is provided. Leave approximately 10 cm space around all sides of the
unit. For the dimensions of the FAX, see p. A2.
Introduction
15
Introduction
•
•
Do not stack boxes or furniture around the power outlet. Keep the area free so
you can reach the outlet quickly. If you notice anything unusual (smoke, strange
odours, noises) around the FAX, unplug the unit immediately. Contact your local
authorised Canon dealer or the Canon help line.
•
Do not allow anything to rest on the power cord, and do not place the unit where
the cord will be walked on. Make sure the cord is not knotted or kinked.
■ Power Supply
•
During electrical storms, disconnect the power cord from the power outlet.
(Please note that any documents stored in the FAX’s memory will be deleted
when you unplug the unit.)
•
Whenever you unplug the FAX, wait at least five seconds before you plug it in
again.
•
Do not plug the FAX into an uninterruptible power supply (UPS).
This product emits low level magnetic flux.
If you use a cardiac pacemaker and feel abnormalities, please move away from this
product and consult your doctor.
16
Introduction
Chapter 1
Chapter 2
❏
Unpacking the FAX ...................................................................................
• Removing Shipping Materials ...............................................................
22
23
❏
Assembling the FAX..................................................................................
24
❏
Making Connections ..................................................................................
• Connecting the Telephone Line Cord and External Devices.................
• Connecting the Power Cord...................................................................
25
25
27
❏
Setting the Language and Country.............................................................
28
❏
Main Components of the FAX...................................................................
• Operation Panel .....................................................................................
Special Function Buttons ....................................................................
210
211
211
❏
Installing the Toner Cartridge ....................................................................
212
❏
Loading Paper ............................................................................................
215
❏
Testing the FAX.........................................................................................
216
Setting Up
21
Setting Up
Chapter 2
Setting Up
Unpacking the FAX
Before unpacking your FAX, be sure to choose a suitable location for it (
p. 15).
Carefully remove all items from the box. You should have someone help you hold the
box while you lift out the FAX and its protective packaging. Save the carton and
packaging in case you need to transport the FAX in the future.
Make sure you have the following items:
MAIN UNIT
PAPER REST
FX-3 TONER
CARTRIDGE
MULTI-PURPOSE
TRAY COVER
SUPPORT TRAYS
DOCUMENT
SUPPORT
POWER CORD
TELEPHONE LINE CORD
DOCUMENTATION
PAPER LOADING WARNING LABEL
DESTINATION LABELS
•
•
22
The actual items may differ in shape and quantity from the one shown above.
Please note that the items included with your FAX may vary depending on the country
of purchase.
Setting Up
Chapter 2
If any items are damaged or missing, notify your local authorised Canon dealer or the
Canon help line immediately.
•
•
Important! Save your sales receipt for proof of purchase in case your unit requires
warranty service.
If you have purchased the optional handset, see Appendix C for the items included.
Follow this procedure to remove the shipping materials. Keep them in case you need
to transport the unit in the future.
1
Remove all shipping
tapes from the FAX.
2
Use both hands to
gently open the
operation panel (it
only opens partially).
Then remove the
protective sheet from
the ADF.
Close the operation
panel by pressing it
down from the centre
until it locks into
place.
The actual shipping materials may differ in shape, quantity, and position from the ones
shown above.
Chapter 2
Setting Up
23
Setting Up
Removing Shipping Materials
Assembling the FAX
Follow this procedure to assemble your FAX:
1
4
Attach the paper
loading warning
label to the left of the
multi-purpose tray.
Insert the ends of the
document support
into the slots on the
unit.
5
Insert the tabs on one
of the support trays
into the corresponding
slots above the facedown delivery slot.
2
Insert the tabs on the
paper rest into the
slots on the unit.
3
Slide the multipurpose tray cover
over the paper rest.
6
Insert the tabs on the
other support tray into
the corresponding
slots above the ADF.
For details on attaching the optional handset to your FAX, see Appendix C.
24
Setting Up
Chapter 2
Making Connections
Your FAX has three jacks on the side for connection of the following:
• Telephone line cord
• Optional handset or telephone
• Additional telephone, answering machine, or data modem
If you only have one telephone line and plan to use your FAX for receiving both faxes
and voice calls, you will need to connect the optional handset, a telephone, or an
answering machine to your unit.
Be sure to connect any external device before using your FAX.
Follow this procedure to connect the telephone line cord and external device(s):
1
Chapter 2
Connect the supplied
telephone line cord to
the
jack, then the
other end to the
telephone line jack on
your wall.
2
Connect the optional
handset or telephone
cord to the
jack.
3
Connect the additional
telephone, answering
machine, or data modem
cord to the
jack.
Setting Up
25
Setting Up
Connecting the Telephone Line Cord and External
Devices
•
•
•
•
26
Canon cannot guarantee that all answering machines will be compatible with your
unit, due to varying specifications.
If you have connected an external device to your FAX, be sure to set the correct
receive mode ( Chapter 8).
To connect an additional telephone as well as an answering machine, connect the
additional telephone to the answering machine, and then the answering machine to
your FAX.
If you connect a data modem to your FAX and you use it extensively, or others access
your PC frequently through the data modem, you may want a dedicated telephone line
for your data modem.
Setting Up
Chapter 2
Connecting the Power Cord
Before connecting the power cord, see Power Supply, p. 16.
Setting Up
Follow this procedure to connect the power cord:
Connect the supplied power cord
to the power cord connector. Then
connect the other end into a
properly grounded 200-240 V AC
three-prong outlet.*
The FAX has no power switch, so its power is on as long as it is plugged in. Once
connected, though, the unit still needs time to warm up before you can use it. Wait
until the LCD no longer displays PLEASE WAIT.
•
•
The FAX is equipped with a threeprong, groundingtype plug provided with a third
(grounding) pin. This plug will only fit into a groundingtype outlet. This is a safety
feature. If you are unable to insert the plug into your outlet, contact an electrician to
replace the outlet. Do not defeat the safety purpose of the groundingtype plug by
breaking off the third prong or using a 3to2 adaptor.*
Do not plug the FAX into the same circuit as an appliance such as an air conditioner,
electric typewriter, television, or copier. Such devices generate electrical noise that
can interfere with your FAX’s ability to send and receive faxes.
When you connect the power cord to an AC outlet for the first time, DISPLAY
LANGUAGE will appear in the LCD display after PLEASE WAIT. In this case, set
the language for the LCD display and the country** ( p. 28).
* The shape of the plug and outlet vary depending on the country of purchase.
** The country selection feature is available for certain countries only.
Chapter 2
Setting Up
27
Setting the Language and Country*
When you connect the power cord to an AC outlet for the first time, you need to select
the language for the LCD display. For some countries, you also need to select the
country where you are using the FAX machine. The FAX machine automatically
switches the selectable settings and the default settings in the menus to suit the
selected country.
Follow this procedure to set the language and country.
After connecting the power cord, the display changes from PLEASE WAIT to
DISPLAY LANGUAGE.
PLEASE WAIT
DISPLAY LANGUAGE
1
Press OK.
2
Press ▼ or ▲ to select the preferred language
for the LCD display.
3
Press OK.
Ex:
Ex:
Ex:
ENGLISH
ENGLISH
DATA ENTRY OK
■ If COUNTRY SELECT does not appear after
DATA ENTRY OK in step 3:
The FAX enters standby mode.
Ex:
15:00
FaxOnly
■ If COUNTRY SELECT appears after DATA ENTRY OK in
step 3:
COUNTRY SELECT
4
Press OK.
5
Press ▼ or ▲ to select the country where you
are using the FAX.
•
Ex:
Ex:
UK
SWITZERLAND
If your country name does not appear, select
OTHERS.
* The country selection feature is available for certain countries only.
28
Setting Up
Chapter 2
6 Press OK.
DATA ENTRY OK
The FAX enters standby mode.
PUT IN CARTRIDGE
Ex:
15:00
FaxOnly
•
•
Chapter 2
To check the settings made by the country selection, you can print the USER’S DATA
LIST ( p. 142).
You can change the language or country setting using the SYSTEM SETTINGS menu
( p. 1410).
Setting Up
29
Setting Up
Once you have selected the language and country, these setting menus will not appear
next time you connect the power cord.
Main Components of the FAX
MULTI-PURPOSE TRAY COVER
PAPER REST
SUPPORT TRAYS
FACE-DOWN DELIVERY
SLOT
DOCUMENT GUIDES
ADF (AUTOMATIC
DOCUMENT FEEDER)
OPERATION PANEL
PAPER GUIDES
MULTI-PURPOSE TRAY
LATCH
FRONT COVER
PAPER DELIVERY
SELECTOR
FACE-UP DELIVERY SLOT
DOCUMENT SUPPORT
FX-3 TONER CARTRIDGE
COMPARTMENT
TRANSFER CHARGING
ROLLER
(DO NOT TOUCH)
PAPER RELEASE
LEVER
FIXING ASSEMBLY
FRONT COVER
210
Setting Up
Chapter 2
Operation Panel
The language used for the Operation Panel varies depending on the country of
purchase. The following illustration shows the Operation Panel in English.
(
•
(
Directory Button
p. 616)
Resolution Button
pp. 72, 102)
• LCD
• C (Clear) Button
(
p. 34)
•
, , ,
Buttons
(
pp. 34, 37)
• OK Button
(
p. 36)
•
Coded Dial Button
pp. 62, 67,614)
•
P Redial/Pause
Button (
pp. 79, 92)
• R Button (
p. 39)
(
Setting Up
•
P
C
01
02
03
04
05
06
07
08
Data
Delayed
Memory
Registration Transmission Reference
09
10
Polling
13
•
11
Report
14
OK
1
Receive
Mode
12
Space
R
2
3
ABC
DEF
4
5
GHI
JKL
6
MNO
7
8
9
PQRS
TUV
WXYZ
0
#
Function
15
T
OneTouch Speed Dialling •
Buttons
(
pp. 62, 63, 615)
•
(
(
•
(
Hook Button
pp. 615, 76)
Start/Copy Button
pp. 102, 103)
Stop Button
pp. 37, 103)
•
Numeric Button
(
p. 32)
Special Function Buttons
•
•
•
•
Chapter 2
Data Registration
Button (
p. 143)
Delayed Transmission
Button (
pp. 714,
716, 717)
Polling Button
(
pp. 910, 914)
Report Button
(
pp. 617, 113, 142)
•
Data
Delayed
Memory
Registration Transmission Reference
Receive
Mode
•
09
10
Polling
13
11
Report
14
Space
15
12
Function
•
•
Memory Reference
Button (
pp. 94,
95, 96, 98)
Receive Mode Button
(
Chapter 8)
Space Button
(
pp. 33, 34)
Function Button
(
p. 36)
Setting Up
211
Installing the Toner Cartridge
This section describes how to install the toner cartridge in the FAX for the very first
time. If you are replacing a used toner cartridge, see p. 126.
Before installing the toner cartridge, be sure to read the following:
• Use only FX3 toner cartridges in your FAX.
• Keep the toner cartridge away from computer screens, disk drives, and floppy
disks. The magnet inside the toner cartridge may harm these items.
• Do not store the toner cartridge in direct sunlight.
• Avoid locations subject to high temperature, high humidity, or rapid changes in
temperature. Store the toner cartridge between 0°C and 35°C.
• Do not expose the toner cartridge to direct sunlight or bright light for longer than
five minutes.
• Store the toner cartridge in its protective bag. Do not open the bag until you are
ready to install the toner cartridge in the unit.
• Save the toner cartridge’s protective bag in case you need to repack and transport
the toner cartridge at a later date.
• Do not store the toner cartridge in a salty atmosphere or where there are corrosive
gases such as from aerosol sprays.
• Do not remove the toner cartridge from the FAX unnecessarily.
• Do not open the drum protective shutter on the toner
cartridge. Print quality may deteriorate if the drum
surface is exposed to light or is damaged.
•
Hold the toner cartridge as shown so that your hand is not
touching the drum protective shutter.
•
Never touch the drum protective shutter. When holding
the toner cartridge, avoid touching the drum protective
shutter with your hands.
•
Do not stand the toner cartridge on end, and do not turn it
upside down. If toner becomes caked in the toner
cartridge, it may prove impossible to free it even by
shaking the toner cartridge.
Do not place the toner cartridge in fire. Toner powder is flammable.
212
Setting Up
Chapter 2
Follow this procedure to install the toner cartridge in the FAX:
Make sure the FAX is plugged in.
2
Lift the latch and open the front cover.
Setting Up
1
Do not open the front cover without
lifting the latch since this may
damage your unit.
3
Remove the new FX3 toner cartridge
from its protective bag.
•
4
Gently rock the toner cartridge from
side to side a few times to distribute the
toner evenly inside it.
•
Chapter 2
Save the protective bag in case you
need to repack the toner cartridge
at a later date.
Poor print quality may result if the
toner is unequally distributed.
Setting Up
213
5
Place and support the toner cartridge on
a flat, clean surface, then gently pull on
the plastic tab to remove the plastic
seal.
•
Use a firm, even pull to avoid
breaking the seal.
SIDE VIEW
PULL WITHIN
THIS RANGE
TOP VIEW
PULL WITHIN
THIS RANGE
6
Hold the toner cartridge by its handle
and insert it into the FAX as far as it
will go, making sure that its tabs are
aligned with the rails inside the unit.
•
7
214
Always hold the toner cartridge by
its handle.
Use both hands to close the front cover.
Setting Up
Chapter 2
Loading Paper
This section explains how to load plain paper in the multipurpose tray.
For complete details on paper requirements and selecting paper for your FAX, see
Chapter 5.
The laser printing process uses high temperatures to fuse toner to the paper. Use
paper that will not melt, vaporize, discolour, or emit dangerous fumes at
temperatures near 170°C. For example, do not use vellum paper in a laser printer.
Make sure any letterhead or coloured paper you use can withstand high
temperatures.
•
•
•
•
•
•
•
•
•
•
Chapter 2
Your FAX supports regular copier paper, cotton bond paper, and typical
letterhead paper. It does not require special paper. Use cutsheet paper only, not
paper that comes on a roll.
Be sure to load paper of the correct size, weight, and quantity recommended for
your FAX ( Chapter 5).
The multipurpose tray is factoryset for loading A4size paper, but you can
change this setting to other paper sizes ( p. 56).
You can choose whether paper is delivered through the faceup or facedown
delivery slot ( p. 54). Choose according to the task you are performing.
The facedown delivery slot can hold up to approximately 50 sheets of paper. To
prevent paper jams, remove paper from this slot before the count reaches 50.
Do not load paper while the FAX is printing.
Do not leave paper stacked in the multipurpose tray for long periods of time
since it may bend or curl and cause problems.
Certain environmental conditions, such as extreme temperatures or humidity,
can cause some paper to misfeed in the multipurpose tray. If you have trouble,
feed one sheet at a time.
Take care not to drop any foreign objects into the multipurpose tray.
Avoid mixing new stock with paper
already loaded in the multipurpose tray.
Adding new stock without removing the
paper already loaded will cause paper
jams. If you must add new stock, remove
the loaded paper and reload it together
with the new stock.
Setting Up
215
Setting Up
Before loading paper, be sure to read the following:
Follow this procedure to load a stack (maximum 10 mm stack height) of A4size plain
paper in the multipurpose tray:
1
Remove the multipurpose tray cover
from the FAX. Prepare a stack of paper
by tapping it on a flat surface to even its
edges.
2
Open the paper guides to the
approximate width of the stack.
3
Insert the stack into the multipurpose
tray ~ (print side facing you and top
edge first), then adjust the paper guides
to the width of the paper Ä.
• Make sure there are no gaps
between the paper guides and the
paper stack.
1
2
2
4
Replace the multipurpose tray cover.
• Be sure to replace this cover to prevent dust accumulating inside the unit.
5
Adjust the paper delivery selector if necessary (
p. 54).
Your FAX is now ready to print.
Testing the FAX
Once you have assembled the FAX, installed the toner cartridge, and loaded paper,
you can make sure the FAX is printing properly by making several copies of a
document ( p. 102). If you have problems in printing, see Chapter 13.
216
Setting Up
Chapter 2
Chapter 3
Registering Information
Guidelines for Entering Numbers, Letters, and Symbols ..........................
• Correcting a Mistake..............................................................................
32
34
❏
Registering Sender Information .................................................................
• What is Sender Information? .................................................................
• Entering the Date and Time...................................................................
• Registering Your FAX Number and Name ...........................................
35
35
36
36
❏
Setting the Telephone Line Type ...............................................................
38
❏
Dialling Through a Switchboard................................................................
• Registering the R Button .......................................................................
39
39
❏
Setting the Summer Time ..........................................................................
311
Registering
Information
❏
Chapter 3
Registering Information
31
Guidelines for Entering Numbers, Letters,
and Symbols
When you come to a step that requires you to enter a name or number, refer to the
table below to determine which numeric button to press for the character you want:
Button
Uppercase Letter
Mode (:A)
Lowercase Letter
Mode (:a)
Uppercase Letter
Mode (:A)
Lowercase Letter
Mode (:a)
Number Mode
(:1)
1
2
ABC
3
DEF
4
GHI
5
JKL
6
MNO
7
PQRS
8
TUV
9
WXYZ
0
#
T
Number Mode (:1)
If you pause for more than 60 seconds between entering data, the unit will automatically
return to standby mode.
32
Registering Information
Chapter 3
■
Changing Between Number and Letter Modes
Press to select number mode (:1), uppercase
letter mode (:A), or lowercase letter mode (:a)
_
:1
(Number mode)
_
:A
(Uppercase letter mode)
_
:a
(Lowercase letter mode)
Entering Letters
1
Press to switch to uppercase letter mode
(:A) or lowercase letter mode (:a).
Ex:
2
Press the numeric button that contains the
letter you want.
Ex:
•
•
3
•
Chapter 3
:A
C
_
:A
CA
_
:A
Press repeatedly until the letter you want
appears. Each button cycles through the
letters it contains.
If you are unsure which button to press
for the letter you want, see p. 32.
Continue entering other letters using the
numeric buttons.
•
_
Registering
Information
■
Ex:
If the next letter you want to enter is
under a different numeric button, simply
press that button until the letter you want
appears.
or
If the next letter you want to enter is
under the same numeric button you
pressed in step 2, press
to move the
cursor to the right. Then press that same
numeric button repeatedly until the letter
you want appears.
To enter a space, press Function then
Space.
Registering Information
33
■
Entering Numbers
1
Press
(:1).
2
Press the numeric button that contains
the number you want.
•
to switch to number mode
Ex:
_
:1
1
_
:1
10_
:1
#
_
:1
# —
_
:1
To enter a space, press Function
then Space.
3
Continue entering other numbers using
the numeric buttons.
■
Entering Symbols
1
Press # repeatedly until the symbol you
want appears.
Ex:
2
If you want to enter another symbol,
press to move the cursor to the right,
then press # repeatedly until the symbol
you want appears.
Ex:
Ex:
Correcting a Mistake
You can delete an entire entry by pressing C. Alternatively, follow this procedure to
correct individual characters:
1
Use or
to move the cursor under
the incorrect character.
Ex:
2
Press the numeric button that contains
the correct letter, to enter it over the
incorrect character.
Ex:
•
3
34
CANE
_N
:A
CANO
_N
:A
If you are unsure which button to
press for the letter you want, see
p. 32.
When you have finished making
corrections, press OK to register your
new entry.
Registering Information
Chapter 3
Registering Sender Information
What is Sender Information?
27-12 2002 10-12 FAX 123 4567
Date and time of
transmission.
YOUR NAME
Your fax or
telephone
number.
You can select if
FAX or TEL is
displayed before
the number
(
TELEPHONE
MARK, p. 14-4).
RECEIVER
001
Receiver’s
name appears
here if you used
memory sending
and dialled their
fax number
using speed
dialling.
You can select
if the sender
information is
printed inside or
outside the
image area
(
TTI
POSITION,
p. 14-4).
The page
number of the
fax is displayed.
Your name or
company name.
To enter the sender information in your FAX, follow the procedures on the following
pages.
Chapter 3
Registering Information
35
Registering
Information
When you receive a fax, the name of the person or company who sent you the fax,
their fax/telephone number, and the date and time of transmission may be printed in
small type at the top of each page. This information is called the Sender information
or the Transmit Terminal Identification (TTI). Similarly, you can register your details
in your FAX so that whenever you send a fax, the other party knows who sent it, and
when it was sent. Below is an example of how your sender information would print
on a fax sent from your unit:
Entering the Date and Time
Follow this procedure to set the current date and time:
1
2
Press Function.
3
Press OK three times.
Press Data Registration.
•
DATA REGSTRATION
USER SETTINGS
The date and time currently set for
your FAX are displayed.
DATE & TIME
Ex:
4
Use the numeric buttons to enter the
correct day, month, year, and time in
this order.*
•
•
•
5
Ex:
2
_0/12 2003 13:30
2
_7/12 2003 15:00
Enter only the last two digits of the
year.
Use the 24hour format for the time
(e.g. 1:00 p.m. as 13:00), and
precede single digits with a zero.
If you make a mistake, press C and
reenter the date and time.
Press OK.
DATA ENTRY OK
UNIT TELEPHONE #
6
Press Stop to return to standby mode.
Ex:
15:00
FaxOnly
Registering Your FAX Number and Name
Follow this procedure to register the fax/telephone number for your FAX, and your
name or company name:
1
2
Press Function.
3
Press OK twice.
Press Data Registration.
DATA REGSTRATION
USER SETTINGS
DATE & TIME
*
36
For certain countries, the date (day, month and year) is shown in a different order.
Registering Information
Chapter 3
4
Use
or
to select UNIT
TELEPHONE #.
5
Press OK.
Ex:
6
Use the numeric buttons to enter your
fax/telephone number (max. 20 digits,
including spaces).
Ex:
•
•
7
TEL=
TEL=
123 4567
To enter a space, press Function
then Space. Spaces are optional
but make the number easier to
read.
To enter a plus sign (+) before the
number, press #.
If you make a mistake, press C and
reenter the number.
Press OK twice.
DATA ENTRY OK
UNIT NAME
Ex:
8
Use the numeric buttons to enter your
name or company name (max. 24
characters, including spaces).
•
•
9
Ex:
_
:A
CANON
_
:A
If you are unsure how to enter
characters, see p. 32.
If you make a mistake, press C and
reenter the name.
Press OK.
DATA ENTRY OK
TX TERMINAL ID
10 Press Stop to return to standby mode.
Ex:
15:00
FaxOnly
To check the sender information registered in your FAX, you can print the USER’S DATA
LIST ( p. 142).
Chapter 3
Registering Information
37
Registering
Information
•
UNIT TELEPHONE #
Setting the Telephone Line Type
Before using your FAX, make sure it is set for the telephone line type of your
telephone system. If you are unsure of your telephone line type, check with your local
telephone company.
Follow this procedure if you need to change the telephone line type setting:
1
Press Function.
2
Press Data Registration.
3
Press OK twice.
DATA REGSTRATION
USER SETTINGS
DATE & TIME
4
Use
or
TYPE.
5
Press OK.
6
Use
or
to select the telephone
line type setting you want.
•
to select TEL LINE
TEL LINE TYPE
Ex:
TOUCH TONE
You can select from the following:
– ROTARY PULSE* (For pulse
dialling)
– TOUCH TONE (For tone
dialling)
7
Press OK.
8
Press Stop to return to standby mode.
R-KEY SETTING
Ex:
15:00
FaxOnly
*ROTARY PULSE is available for certain countries only.
38
Registering Information
Chapter 3
Dialling Through a Switchboard
A PBX (Private Branch Exchange) is an onsite telephone switchboard. If your FAX
is connected through a PBX or other telephone switching system, you have to dial the
outside line access number first, and then the number of the party you are calling.
To facilitate this procedure, you can register the PBX access type and the outside line
access number under the R button so that you only need to press this button before
dialling the fax/telephone number you want to reach. See below for details.
Registering the R Button
Follow this procedure to register the PBX access type and outside line access number
under the R button:
Press Function.
2
Press Data Registration.
3
Press OK twice.
DATA REGSTRATION
Registering
Information
1
USER SETTINGS
DATE & TIME
4
Use
or
SETTING.
5
Press OK.
6
Use
7
Press OK.
8
Use
or
to select the access type
of your switching system.
•
Chapter 3
or
to select R-KEY
R-KEY SETTING
Ex:
PSTN
to select PBX.
PBX
Ex:
HOOKING
You can select from the following:
– PREFIX
– HOOKING
Registering Information
39
■
If you selected HOOKING in step 8:
9
Press OK.
10 Press Stop to return to standby mode.
■
If you selected PREFIX in step 8:
9
Press OK.
10 Use the numeric buttons to enter the
REPORT SETTINGS
Ex:
15:00
Ex:
123456
outside line access number (max. 19
digits).
11 Press Redial/Pause to enter a pause.
Ex:
12 Press OK.
13 Press Stop to return to standby mode.
310
Registering Information
FaxOnly
123456P
REPORT SETTINGS
Ex:
15:00
FaxOnly
Chapter 3
Setting the Summer Time*
Some countries adopt the summer time system that shifts the clock time ahead or back
according to the change in seasons. You can select if the time information in your
FAX changes to match your country’s summer time system and set the day and time
when the summer time begins and ends.
1
Press Function.
2
Press Data Registration.
3
Press OK.
4
Use
or
to select SYSTEM
SETTINGS.
5
Press OK.
6
Use
7
Press OK.
8
Use
or
want.
•
USER SETTINGS
SYSTEM SETTINGS
UN/LOCK PHONE
to select SUMMER TIME.
SUMMER TIME
Ex:
to select the setting you
Registering
Information
or
DATA REGSTRATION
ON
Ex:
ON
You can select from the following:
– ON
Enables the summer time.
– OFF
Disables the summer time.
■
If you selected OFF in step 8:
9
Press OK.
10 Press Stop to return to standby mode.
TEL REGISTRATION
Ex:
15:00
FaxOnly
*The Summer Time feature is available for certain countries only.
Chapter 3
Registering Information
311
■
If you selected ON in step 8:
9
Press OK three times.
BEGIN DATE/TIME
MONTH
Ex:
10 Use
or
to select the month in
which the summer time starts.
MARCH
Ex:
11 Press OK twice.
APRIL
WEEK
Ex:
12 Use
or
to select the week in
which the summer time starts.
•
LAST WEEK
Ex:
FIRST WEEK
You can select from the following:
– FIRST WEEK
– SECOND WEEK
– THIRD WEEK
– FOURTH WEEK
– LAST WEEK (fourth or fifth
week depending on the
selected month)
13 Press OK twice.
DAY
Ex:
14 Use
or
to select the day of the
week on which the summer time starts.
Ex:
15 Press OK twice.
time at which the summer time
compensation is made.
•
312
SUNDAY
TIME
Ex:
16 Use the numeric buttons to enter the
SUNDAY
Ex:
0
_1:00
0
_2:00
Use the 24hour format for the
time (e.g., 2:00 p.m. as 14:00) and
precede single digits with a zero.
Registering Information
Chapter 3
17 Press OK three times.
END DATE/TIME
MONTH
Ex:
OCTOBER
18 Use
or
and OK to select the
month, week, day of the week, and time
when the summer time ends, as in steps
10 to 16 for the BEGIN DATE/TIME
settings. (e.g. OCTOBER LAST WEEK,
SUNDAY and 03:00)
19 Press OK.
Ex:
15:00
FaxOnly
Registering
Information
20 Press Stop to return to standby mode.
TEL REGISTRATION
Chapter 3
Registering Information
313
314
Registering Information
Chapter 3
Chapter 4
Document Handling
Document Requirements............................................................................
• Scanned Area of a Document ................................................................
42
42
❏
Loading Documents ...................................................................................
• Adding Pages to the Document in the ADF ..........................................
43
44
Document Handling
❏
Chapter 4
Document Handling
41
Document Requirements
The documents you load in the ADF for sending and copying must meet the following
requirements:
Onepage document
Multipage document of the same
thickness and weight
Size
(W × L)
Max. 216 mm × Approx. 1 m
Min. 148 × 105 mm
Max. 216 × 355.6 mm
Min. 148 × 105 mm
Quantity
1 sheet
Max. 30 A4 or lettersize sheets*
Max. 10 legalsize sheets*
Thickness
0.06 to 0.23 mm
Weight
35 to 240 g/m
2
0.06 to 0.13 mm
40 to 90 g/m2
■
•
Problem Documents
•
Remove all fasteners (staples, paper clips, etc.) before loading the document in
the ADF.
Make sure any glue, ink, or correction fluid on the document is completely dry
before loading it in the ADF.
If you have a document that will not feed properly in the ADF, make a photocopy
of the document and load the copy instead.
If you will be sending a document that you have printed from your FAX, be sure
to use facedown delivery when printing that document ( p. 54).
•
•
•
To prevent document jams in the ADF, do not use any of the following:
– Wrinkled or creased paper
– Carbon paper or carbonbacked
paper
– Curled or rolled paper
– Coated paper
– Torn paper
– Onion skin or thin paper
Scanned Area of a Document
The shaded area shows the scanned area of
a document. Make sure your document’s
text and graphics fall within this area.
MAX. 4 mm
A4
MAX. 4 mm
MAX. 3 mm
*
42
MAX. 3 mm
75 g/m2 paper
Document Handling
Chapter 4
Loading Documents
Follow this procedure to load documents in the ADF:
1
Adjust the document guides to the
width of the document.
2
Gently insert the top of the document,
face down, in the ADF until you hear a
beep.
•
Tap multipage documents on a flat
surface to even the edges before
inserting them in the ADF.
•
•
For a multipage document, the pages are fed one by one from the bottom of the stack.
Wait until all pages of your document have been scanned before starting a new job.
■ Problems With Multipage Documents
If you have trouble feeding multipage documents in the ADF, remove the stack and
tap it on a flat surface to even the edges. Then “slant” the stack so that its front edge
is bevelled, and insert the stack in the ADF.
To avoid feeding problems, make sure the document meets the document requirements
( p. 42).
Chapter 4
Document Handling
43
Document Handling
The document is now ready for scanning.
Adding Pages to the Document in the ADF
If you need to add pages to your document in the ADF, wait until the last page starts
feeding, then load up to 30 additional pages (10 legal size). The last and first page
should overlap by about 2.5 cm.
2.5 cm
44
Document Handling
Chapter 4
Chapter 5
Paper Handling
Paper Requirements ...................................................................................
• Printable Area ........................................................................................
52
53
❏
Selecting Paper for Your FAX...................................................................
53
❏
Loading Paper ............................................................................................
53
❏
Selecting FaceUp or FaceDown Paper Delivery.....................................
54
❏
Changing the Paper Size Setting................................................................
56
❏
Adjusting the Toner Saver Setting .............................................................
58
Paper Handling
❏
Chapter 5
Paper Handling
51
Paper Requirements
You can load the following paper in the multipurpose tray:
Paper Size Setting
Size (W × L)
Min. 92.4 × 127 mm
Max. 216 × 356 mm
A4
210 × 297 mm/
(8.27 × 11.69 in.)
LTR (Letter)
215.9 × 279.4 mm
(8.5 × 11 in.)
LGL (Legal)
215.9 × 355.6 mm
(8.5 × 14 in.)
CUSTOM1/LONG*
216 × 317 mm to
216 × 340 mm*
CUSTOM2/SHORT*
216 × 254 mm to
216 × 285 mm*
Weight
Quantity
2
6490 g/m
1 sheet: 64105 g/m2
Max. stack height:
10 mm
(Approx. 100 sheets of
75 g/m2 paper)
Once you have decided which paper you want to load, be sure to do the following:
• Check that your paper is compatible with the FAX ( p. 53).
• Check that the paper size setting of the multipurpose tray is set for the paper size
you are loading ( p. 56).
• Check that paper delivery is set correctly for the task you are performing
( p. 54).
• Check that you have loaded the paper correctly in the multipurpose tray
( p. 215).
*For this setting, you may need to load fewer sheets.
52
Paper Handling
Chapter 5
Printable Area
The shaded area shows the printable
area of A4size paper.
MAX. 4 mm
A4
FEED
DIRECTION
MAX. 10 mm
MAX. 4 mm
MAX. 5 mm
Selecting Paper for Your FAX
•
To prevent paper jams in the multipurpose tray, do not use any of the following:
– Wrinkled or creased paper
– Curled or rolled paper
– Coated paper
– Torn paper
– Damp paper
– Onion skin or very thin paper
•
The following types of paper do not print well:
– Highly textured paper
– Very smooth paper
– Shiny paper
•
•
•
Make sure the paper is free from dust, lint, and oil stains.
Be sure to test paper before purchasing large quantities.
Store all paper wrapped and on a flat surface until ready to use. Keep opened
packs in their original packaging, in a cool, dry location.
Store paper at 18°C24°C, 40%60% relative humidity.
•
Loading Paper
For instructions on loading paper in the multipurpose tray, see p. 215.
Chapter 5
Paper Handling
53
Paper Handling
Follow these guidelines when selecting paper:
Selecting Face-Up or Face-Down Paper
Delivery
■ Paper Path
Understanding how paper feeds through the FAX will help you determine which
paper delivery slot is appropriate for the task you are performing.
First, the paper travels to the toner cartridge where a laser beam “draws” the print
image on the drum, which in turn applies toner to the paper. The paper travels to the
fixing assembly where the toner is “fixed” (fused) to the paper. The paper then exits
the FAX through the faceup delivery slot (front of the unit) or the facedown delivery
slot (top of the unit).
FACE-DOWN
DELIVERY
PAPER DELIVERY
SELECTOR
FACE-UP DELIVERY
54
Paper Handling
Chapter 5
■ Selecting Paper Delivery
Before selecting paper delivery, be sure to take note of the following:
• Always set the paper delivery selector before printing ( below).
• Changing paper delivery while the unit is printing will cause problems. Wait for
the printout to exit the unit completely before changing paper delivery.
• The facedown delivery slot can hold up to approximately 50 sheets of paper. To
prevent paper jams, remove paper from this slot before the count reaches 50.
• Make sure there is enough room for the paper to exit from the faceup delivery
slot. Remove each sheet as it is delivered from this slot.
• Never pull the paper as it comes out of the unit.
Choose paper delivery according to the task you are performing.
Select faceup or facedown delivery with the paper delivery selector.
FACE-DOWN
DELIVERY
FACE-UP
DELIVERY
When using faceup delivery, you must remove each sheet as it is delivered.
Failure to do this may cause jams in the faceup delivery slot and result in damage to
your unit.
Chapter 5
Paper Handling
You can also use faceup delivery when
copying or receiving a large number of pages.
In this case, place the FAX near the edge of a
table so that the pages can fall away from the
unit and avoid blocking the faceup delivery
slot. You may want to place a box below the
FAX so that the pages can collect in it.
Paper Handling
55
Changing the Paper Size Setting
The multipurpose tray is factoryset for loading A4size paper. If you want to load a
different paper size ( p. 52), follow this procedure to change the paper size setting:
1
Press Function.
2
Press Data Registration.
3
Press OK.
4
Use ▼ or ▲ to select PRINTER SETTINGS.
5
Press OK.
6
Use
7
Press OK.
8
Use
or
to select the paper size you want
for the multipurpose tray.
•
•
or
USER SETTING
PRINTER SETTINGS
RX REDUCTION
to select PAPER SIZE.
PAPER SIZE
Ex:
A4
You can select from the following:
– A4 (Default)
– LTR
– LGL
– CUSTOM
For details on the paper sizes above, see
p. 52
■
If you selected A4, LTR, or LGL in step 8:
9
Press OK.
10 Press Stop to return to standby mode.
56
DATA REGSTRATION
■
If you selected CUSTOM in step 8:
9
Press OK.
Paper Handling
ECONOMY PRT
Ex:
Ex:
15:00
FaxOnly
CUSTOM1/LONG
Chapter 5
10 Use
or
to select the custom paper size
setting.
•
•
You can select from the following:
– CUSTOM1/LONG (Default)
– CUSTOM2/SHORT
For details on the paper sizes above, see
p. 52.
11 Press OK.
Ex:
15:00
FaxOnly
Paper Handling
12 Press Stop to return to standby mode.
ECONOMY PRT
Chapter 5
Paper Handling
57
Adjusting the Toner Saver Setting
By enabling the toner saver setting, you can reduce toner consumption of the toner
cartridge by approximately 30% to 40%. This will extend the toner cartridge life.
By enabling this setting, print quality will be reduced. For highest print quality,
disable this setting.
Follow this procedure to enable or disable the toner saver setting:
1
Press Function.
2
Press Data Registration.
3
Press OK.
4
Use
5
Press OK.
6
Use
7
Press OK.
8
Use
•
9
or
or
or
USER SETTINGS
to select PRINTER SETTINGS.
PRINTER SETTINGS
RX REDUCTION
to select ECONOMY PRT.
ECONOMY PRT
Ex:
OFF
to select the setting you want.
You can select from the following:
– ON (Enable toner saving)
– OFF (Disable toner saving)
Press OK.
10 Press Stop to return to standby mode.
58
DATA REGSTRATION
Paper Handling
TONER SUPPLY LOW
Ex:
15:00
FaxOnly
Chapter 5
Chapter 6
Speed Dialling
What is Speed Dialling?.............................................................................
• Speed Dialling Methods ........................................................................
62
62
❏
Registering OneTouch Speed Dialling .....................................................
63
❏
Registering Coded Speed Dialling.............................................................
67
❏
Registering Group Dialling........................................................................
611
❏
Using Speed Dialling .................................................................................
• Sending a Document With Speed Dialling ............................................
• Making a Telephone Call With Speed Dialling.....................................
614
614
615
❏
Dialling with the Directory ........................................................................
616
❏
Printing Speed Dialling Lists .....................................................................
617
Speed Dialling
❏
Chapter 6
Speed Dialling
61
What is Speed Dialling?
Instead of having to dial a fax or telephone number using regular dialling (i.e. with
the numeric buttons), you can simplify the dialling procedure by registering the fax/
telephone number for speed dialling. This will reduce the number of buttons you need
to press to dial the fax/telephone number, making it convenient for frequently dialled
numbers.
Speed Dialling also allows you to register several fax numbers under one speed
dialling button or code so that you can send a document to all those fax numbers in
one operation.
See below for details on the different speed dialling methods.
Speed Dialling Methods
Your FAX offers the following speed dialling methods:
■ OneTouch Speed Dialling (p. 63)
Register a fax/telephone number under a onetouch speed dialling button so that you
only have to press one button to dial that fax/telephone number.
There are 15 onetouch speed dialling buttons available for you to register fax/
telephone numbers.
■ Coded Speed Dialling (p. 67)
Register a fax/telephone number under a coded speed dialling code so that you only
have to press Coded Dial and enter the registered twodigit code (using the numeric
buttons) to dial that fax/telephone number.
There are 100 codes available for you to register fax/telephone numbers.
■ Group Dialling (p. 611)
“Group” up to 114 fax numbers together, so you can send to those fax numbers in one
quick operation. A group is registered under a onetouch speed dialling button or a
coded speed dialling code.
62
Speed Dialling
Chapter 6
Registering One-Touch Speed Dialling
By registering a fax/telephone number under a onetouch speed dialling button, you
can simplify dialling of that number to the press of a single button.
When you register onetouch speed dialling, you will:
– assign one of the 15 onetouch speed dialling buttons for the fax/telephone
number you want to register.
– register the fax/telephone number under that onetouch speed dialling button.
– register a name for the onetouch speed dialling button. This name appears in
speed dialling lists, in reports, and at the top of the recipient’s fax if you use
memory sending ( p. 75).
– set the transmission type for the fax number you have registered. You can set a
subaddress and/or password if the other party’s fax machine requires these
settings.
Follow this procedure to register onetouch speed dialling:
1
Press Function.
2
Press Data Registration.
3
Use
4
Press OK twice.
or
DATA REGSTRATION
to select TEL REGISTRATION.
TEL REGISTRATION
1-TOUCH SPD DIAL
Ex:
Use
or
to select the onetouch speed
dialling button (01 to 15) under which you
want to register the fax/telephone number.
•
•
6
Ex:
If a onetouch speed dialling button has
already been registered, the number
registered under that button appears.
If a group is already registered under a
onetouch speed dialling button, GROUP
DIAL appears.
Press OK twice.
TELEPHONE NUMBER
Ex:
Chapter 6
04=
TEL=_
Speed Dialling
Speed Dialling
5
01=
63
7
Use the numeric buttons to enter the fax/
telephone number you want to register (max.
120 digits, including spaces and pauses).
•
•
•
•
•
8
Ex:
TEL=20 545 8545_
To enter a space, press Function then
Space. Spaces are optional and are
ignored during dialling.
To enter a pause, press Redial/Pause
( p. 92).
To correct a mistake in the number,
press
to delete the rightmost digit.
Alternatively, press C to delete the entire
number.
To cancel onetouch speed dialling for
the button you selected, press C then OK.
Press Stop to return to standby mode.
The fax/telephone number and name
registered under that button will be
deleted.
If you have already registered a number
that you want to keep, ignore this step.
Press OK twice.
DATA ENTRY OK
NAME
Ex:
9
Use the numeric buttons to enter a name for
the onetouch speed dialling button (max. 16
characters, including spaces).
• If you are unsure how to enter characters,
see p. 32.
• If you have already registered a name that
you want to keep, ignore this step.
10 Press OK.
Ex:
_
:A
Canon EUROPA
_
DATA ENTRY OK
OPTIONAL SETTING
64
Speed Dialling
Chapter 6
11 This completes the basic onetouch speed
dialling settings.
To continue registering other onetouch speed
dialling buttons, press Function then Data
Registration and repeat the procedure from
step 5.
or
To end registering onetouch speed dialling
buttons, press Stop to return to standby mode.
or
To register the transmission type for the
current button you are registering, continue
with the steps below.
12 Press OK.
13 Use
or
Ex:
Ex:
05=
15:00
FaxOnly
Ex:
OFF
to select ON.
ON
14 Press OK twice.
TX TYPE
Ex:
REGULAR TX
15 Use
or
to select the transmission type
setting you want.
•
■
You can select from the following:
– REGULAR TX
Normal transmission. (Choose this
setting if you previously set PSWD/
SUBADDRESS and no longer want to
send with this setting.)
– PSWD/SUBADDRESS
Transmission with a subaddress and/
or password. For details, see the
following page.
If you selected REGULAR TX in step 15:
Ex:
17 Press Stop to return to standby mode.
Ex:
05=
15:00
FaxOnly
Speed Dialling
16 Press OK.
Chapter 6
Speed Dialling
65
■ If you selected PSWD/SUBADDRESS in step 15:
The other party’s fax machine may require an ITUT standard subaddress and/or
password to receive faxes. The subaddress/password you register here must match
exactly the one(s) registered on the other party’s fax machine. Contact the other party
to check their settings.
When sending with a subaddress/password, the other party’s fax machine receives
the fax only if your subaddress/password matches theirs. Their fax machine then
handles the received fax according to the feature they are using.
You also need to register a subaddress/password when polling a fax machine that
requires these settings ( p. 99).
Continue with the steps below to register a subaddress/password:
16 Press OK twice.
17 If a subaddress is required, use the numeric
SUBADDRESS
Ex:
1234
buttons to enter it.
•
•
If a subaddress is not required, ignore this
step.
If you have already registered a subaddress
that you want to keep, ignore this step.
18 Press OK twice.
19 If a password is required, use the numeric
PASSWORD
Ex:
4321
buttons to enter it.
•
•
If a password is not required, ignore this
step.
If you have already registered a password
that you want to keep, ignore this step.
20 Press OK.
Ex:
05=
21 To continue registering other onetouch speed
dialling buttons, repeat the procedure from
step 5.
or
Press Stop to return to standby mode.
•
•
66
Ex:
15:00
FaxOnly
Use the destination labels provided with your FAX to label the onetouch speed
dialling buttons. Stick the labels above each corresponding button.
To check your entries, you can print a list of all the numbers and names registered for
onetouch speed dialling ( p. 617).
Speed Dialling
Chapter 6
Registering Coded Speed Dialling
By registering a fax/telephone number under a coded speed dialling code, you can
simplify dialling of that number to pressing Coded Dial and entering the registered
twodigit code.
When you register coded speed dialling, you will:
– assign one of the 100 codes for the fax/telephone number you want to register.
– register the fax/telephone number under that coded speed dialling code.
– register a name for the coded speed dialling code. This name appears in speed
dialling lists, in reports, and at the top of the recipient’s fax if you use memory
sending ( p. 75).
– set the transmission type for the fax number you have registered. You can set a
subaddress and/or password if the other party’s fax machine requires these
settings.
Follow this procedure to register coded speed dialling:
1
Press Function.
2
Press Data Registration.
3
Use
4
Press OK.
5
Use
or
DIAL.
6
Press OK.
Ex:
7
Use
or
to select the coded speed
dialling code (00 to 99) under which you
want to register the fax/telephone number.
Ex:
•
•
Chapter 6
to select TEL REGISTRATION.
TEL REGISTRATION
1-TOUCH SPD DIAL
to select CODED SPEED
CODED SPEED DIAL
00=
01=
Alternatively, press Coded Dial and use
the numeric buttons to enter the code.
If a coded speed dialling code has already
been registered, the number registered
under that code appears.
If a group is already registered under a
coded speed dialling code, GROUP
DIAL appears.
Speed Dialling
•
or
DATA REGSTRATION
Speed Dialling
67
8
Press OK twice.
TELEPHONE NUMBER
Ex:
9
Use the numeric buttons to enter the fax/
telephone number you want to register (max.
120 digits, including spaces and pauses).
•
•
•
•
•
Ex:
TEL=_
TEL=3 3758 2111_
To enter a space, press Function then
Space. Spaces are optional and are
ignored during dialling.
To enter a pause, press Redial/Pause
( p. 92).
To correct a mistake in the number,
press
to delete the rightmost digit.
Alternatively, press C to delete the entire
number.
To cancel coded speed dialling for the
code you selected, press C then OK.
Press Stop to return to standby mode.
The fax/telephone number and the name
registered under that code will be deleted.
If you have already registered a number
that you want to keep, ignore this step.
10 Press OK twice.
DATA ENTRY OK
NAME
Ex:
11 Use the numeric buttons to enter a name for
the coded speed dialling code (max.
16 characters, including spaces).
•
•
68
Speed Dialling
Ex:
_
:A
Canon Inc.
_
:a
If you are unsure how to enter characters,
see p. 32.
If you have already registered a name that
you want to keep, ignore this step.
Chapter 6
12 Press OK.
DATA ENTRY OK
OPTIONAL SETTING
13 This completes the basic coded speed dialling
settings.
To continue registering other coded speed
dialling codes, press Function then Data
Registration and repeat the procedure from
step 7.
or
To end registering coded speed dialling
codes, press Stop to return to standby mode.
or
To register the transmission type for the
current code you are registering, continue
with the steps below.
14 Press OK.
15 Use
or
Ex:
Ex:
02=
15:00
Ex:
OFF
to select ON.
ON
16 Press OK twice.
TX TYPE
Ex:
17 Use
•
Chapter 6
REGULAR TX
to select the transmission type setting you want.
You can select from the following:
– REGULAR TX
Normal transmission. (Choose this setting if you previously set
PSWD/SUBADDRESS and no longer want to send with this setting.)
– PSWD/SUBADDRESS
Transmission with a subaddress and/or password. For details, see the
following page.
If you selected REGULAR TX in step 17:
18 Press OK.
Ex:
19 Press Stop to return to standby mode.
Ex:
02=
15:00
FaxOnly
Speed Dialling
69
Speed Dialling
■
or
FaxOnly
■ If you selected PSWD/SUBADDRESS in step 17:
The other party’s fax machine may require an ITUT standard subaddress and/or
password to receive faxes. The subaddress/password you register here must match
exactly the one(s) registered on the other party’s fax machine. Contact the other party
to check their settings.
When sending with a subaddress/password, the other party’s fax machine receives
the fax only if your subaddress/password matches theirs. Their fax machine then
handles the received fax according to the feature they are using.
You also need to register a subaddress/password when polling a fax machine that
requires these settings ( p. 99).
Continue with the steps below to register a subaddress/password:
18 Press OK twice.
19 If a subaddress is required, use the numeric
SUBADDRESS
Ex:
1234
buttons to enter it.
• If a subaddress is not required, ignore this
step.
• If you have already registered a subaddress
that you want to keep, ignore this step.
20 Press OK twice.
21 If a password is required, use the numeric
PASSWORD
Ex:
4321
buttons to enter it.
•
•
If a password is not required, ignore this
step.
If you have already registered a password
that you want to keep, ignore this step.
22 Press OK.
Ex:
02=
23 To continue registering other coded speed
dialling codes, repeat the procedure from
step 7.
or
Press Stop to return to standby mode.
Ex:
15:00
FaxOnly
To check your entries, you can print a list of all the numbers and names registered for coded
speed dialling ( p. 617). You may want to keep this list near your FAX to refer to it
when dialling.
610
Speed Dialling
Chapter 6
Registering Group Dialling
If you frequently send documents to the same group of fax numbers, you can “group”
these numbers under a onetouch speed dialling button or coded speed dialling code.
You can then send to all the fax numbers in the group in one quick and simple
operation.
When you register group dialling, you will:
– assign a onetouch speed dialling button or a coded speed dialling code for the
group of fax numbers you want to register.
– group up to 114 fax numbers under that button or code. The fax numbers must
already be registered for onetouch or coded speed dialling (i.e. you cannot enter
the fax numbers with the numeric buttons).
– register a name for the group. This name appears in speed dialling lists.
Follow this procedure to register group dialling:
1
Press Function.
2
Press Data Registration.
3
Use
4
Press OK.
5
Use
6
Press OK.
7
Select a onetouch speed dialling button or
coded speed dialling code under which you
want to register the group.
Chapter 6
or
to select TEL REGISTRATION.
TEL REGISTRATION
1-TOUCH SPD DIAL
to select GROUP DIAL.
To register a group under a onetouch
speed dialling button:
Use
or
to select the onetouch
speed dialling button (01 to 15) under
which you want to register the group.
• If a onetouch speed dialling button
has already been registered,
1-TOUCH SPD or GROUP DIAL
appears.
GROUP DIAL
Ex:
Ex:
01=1-TOUCH SPD
03=
Speed Dialling
❏
or
DATA REGSTRATION
Speed Dialling
611
❏
To register a group under a coded speed
dialling code:
Press Coded Dial, then use the numeric
buttons to enter the coded speed dialling
code (00 to 99) under which you want to
register the group.
• If a coded speed dialling code has
already been registered, CODED
SPEED or GROUP DIAL appears.
Ex:
21=
.
If you wish to register a group under a button or code already
registered for speed dialling, you must delete the previous
information first ( pp. 64, 68).
8
Press OK twice.
TELEPHONE NUMBER
Ex:
9
Enter the onetouch and/or coded speed
dialling numbers you want to register in the
group.
❏
❏
To enter a fax number registered for
onetouch speed dialling:
Press the onetouch speed dialling
button(s) assigned to the number(s) you
want to register in the group.
To enter a fax number registered for
coded speed dialling:
Press Coded Dial, then use the numeric
buttons to enter the twodigit code
assigned to the number you want to
register in the group. Repeat for other
codes.
•
•
•
612
TEL=
Speed Dialling
Ex:
Ex:
01=905 795 1111
01=03 3758 2111
The number registered under the button or code you enter appears.
You can also enter groups registered under buttons or codes. In this
case, GROUP DIAL appears.
You cannot enter numbers not registered for onetouch or coded speed
dialling (i.e. with the numeric buttons).
Chapter 6
•
•
•
To add fax numbers to a previously registered group, simply enter them
as explained in this step.
If you enter the wrong destination, or if you want to delete a destination
already registered in a group, use
or
to select that entry, then
press C.
To cancel group dialling for the button or code you selected, press C
until all entries are deleted, then press OK. Press Stop to return to
standby mode. All fax numbers and the name of the group registered
under that button or code will be deleted.
10 Press OK twice.
NAME
Ex:
11 Use the numeric buttons to enter a name for
Ex:
the group (max.16 characters, including
spaces).
•
•
_
:A
Canon GROUP 2_:1
If you are unsure how to enter characters,
see p. 32.
If you have already registered a name that
you want to keep, ignore this step.
12 Press OK.
DATA ENTRY OK
Ex:
04=1-TOUCH SPD
13 To continue registering other groups, repeat
the procedure from step 7.
or
Press Stop to return to standby mode.
•
15:00
FaxOnly
If you registered groups under onetouch speed dialling buttons, use the destination
labels provided with your FAX to label the buttons. Stick the labels above each
corresponding button.
To check your entries, you can print a list of all the numbers and names registered for
group dialling ( p. 617). You may want to keep this list near your FAX to refer to
it when dialling.
Speed Dialling
•
Ex:
Chapter 6
Speed Dialling
613
Using Speed Dialling
Once you have registered fax/telephone numbers for onetouch speed dialling
( p. 63), coded speed dialling ( p. 67), or group dialling ( p. 611), you can
begin to send documents or make telephone calls with speed dialling.
Sending a Document With Speed Dialling
Follow this procedure to send a document using onetouch speed dialling, coded
speed dialling, or group dialling:
1
Load the document, face down in the ADF
( p. 43).
•
•
2
❏
(Currently used memory)
DOCUMENT READY
(Standby to scan)
Onetouch speed dialling button:
Press the onetouch speed dialling button you want.
Coded speed dialling code:
Press Coded Dial, then use the numeric buttons to enter the twodigit
code you want.
• If you make a mistake, press Stop and repeat this step.
• NO TEL # appears if no fax/telephone number or group is assigned
to the speed dialling button or code you pressed.
Press Start/Copy to begin scanning for sending, or wait a few seconds for the
FAX to begin scanning automatically.
•
614
MEMORY USED 0%
Enter the onetouch speed dialling button or coded speed dialling code
assigned to the fax number or group you want to send to.
❏
3
To adjust the resolution and contrast,
see pp. 72, 73.
You may be unable to send if the memory
used (shown in the LCD) is close to
100%. To free up space in the FAX’s
memory: print, send, or delete any
documents you no longer need to be
stored in memory ( p. 94).
Ex:
Speed Dialling
If you do not want the FAX to begin scanning automatically after a few
seconds, disable the TIME OUT setting ( p. 146).
Chapter 6
Making a Telephone Call With Speed Dialling
Follow this procedure to dial a telephone number registered for onetouch or coded
speed dialling on your FAX:
1
Make sure you have connected the optional
handset or a telephone to the FAX
( p. 25).
2
Press Hook.
•
3
TEL=
You can also lift the handset instead of
pressing Hook.
Enter the onetouch speed dialling button or coded speed dialling code
assigned to the telephone number you want to dial.
❏
❏
Onetouch speed dialling button:
Press the onetouch speed dialling button you want.
Coded speed dialling code:
Press Coded Dial, then use the numeric buttons to enter the twodigit
code you want.
• If you make a mistake, press Hook or hang up the handset and start
again from step 2.
• NO TEL # appears if no fax/telephone number is assigned to the
speed dialling button or code you pressed.
• NOT AVAILABLE appears if you entered a speed dialling button or
code assigned to a group of fax numbers.
When you hear the other party answer the call, pick up the handset to start
talking.
5
When you finished, simply hang up.
Speed Dialling
4
Chapter 6
Speed Dialling
615
Dialling with the Directory
If you forget under which of the onetouch speed dialling buttons, coded speed
dialling codes, or groups that you registered a fax/telephone number, you can dial the
correct number just knowing the other party’s name, using the directory function.
Also, you can look up the fax/telephone number of the other party.
Follow this procedure to send a document with the directory function:
1
Load the document, face down in the ADF
( p. 43).
•
2
Press Directory.
3
Use the numeric buttons to enter the first
letter of the other party’s name you are
looking for.
04=Canon EUROPA
4
Press
or
to scroll through the names
until the name you are looking for appears.
01=Canon Inc.
•
•
•
5
616
To adjust the resolution and contrast, see
pp. 72, 73.
1ST LETT OF NAME
If you press
when the last entry in the
directory is displayed, the list returns to
the first entry in the directory.
A twodigit number appears next to the
name registered under a onetouch speed
dialling button. An asterisk ( ) and a
twodigit number appear next to the
name registered under a coded speed
dialling code.
After the name appears, you can display
the registered fax/telephone number by
pressing or
.
Press Start/Copy twice to begin scanning for
sending, or wait a few seconds for the FAX to
begin scanning automatically.
Speed Dialling
Chapter 6
Printing Speed Dialling Lists
To check the fax/telephone numbers and names registered for speed dialling, you can
print the speed dialling lists. You may want to keep these lists near your FAX to refer
to them when dialling.
Follow this procedure to print speed dialling lists:
1
2
Press Function.
3
Use
4
Press OK.
5
Use
or
to select the list you want to
print.
• You can select from the following:
– 1-TOUCH LIST
– CODED DIAL LIST
– 1-TOUCH (DETAIL)
– CODED (DETAIL)
– GROUP DIAL LIST
■
If you selected GROUP DIAL LIST in step 5:
6
Press OK.
Press Report.
to select SPEED DIAL LIST.
SPEED DIAL LIST
1-TOUCH LIST
The FAX prints the list.
■
If you selected a list other than GROUP DIAL LIST in
step 5:
6
Press OK.
SORTED OUTPUT
YES=( )
7
NO=(#)
Select in what order you want the lists to be printed.
Press to print the list with the destination names (CONNECTION ID on the
reports) in alphabetical order (sorted).
or
Press # to print the list in code or button order (unsorted).
• The FAX prints the list.
Samples of the lists are shown on the following pages.
Chapter 6
Speed Dialling
617
Speed Dialling
•
or
ACTIVITY REPORT
■
1TOUCH SPD DIAL LIST 1
27/12 2002 17:23 FAX 123 4567
CANON
001
27/12 2002 17:23***********************************
FAX 123 4567
CANON
*** 1-TOUCH SPD DIAL LIST 1 ***
***********************************
001
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
NO.
[
[
[
[
[
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
CONNECTION
IDSPD DIAL LIST TX
1-TOUCH
1 TYPE
CONNECTION TEL
01]
03]
04]
05]
12]
905 795 1111
GROUP DIAL
2 50921
NO.
1 432 2060
[
12]
2 887 0166
[
[
[
[
01]
03]
04]
05]
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
Canon CANADA
GROUP 2
Canon OPTICS
PSWD/SUBADD.
AUSTRALIA
Canon AUSTRALIA Canon
REGULAR
TX
2 887 0166
905 795 1111
GROUP DIAL
2 50921
1 432 2060
Canon CANADA
Canon GROUP 2
Canon ITALIA
Canon OPTICS
IF YOU PRESS # IN STEP 7
(
p. 6-17), THE DESTINATIONS ARE
LISTED IN BUTTON ORDER
(UNSORTED).
■
REGULAR TX
TX TYPE
CONNECTION
REGULAR TX ID
CONNECTION
TEL ITALIA
Canon
REGULAR TX
REGULAR TX
REGULAR TX
PSWD/SUBADD.
IF YOU PRESS
IN STEP 7
(
p. 6-17), THE DESTINATIONS ARE
LISTED IN ALPHABETICAL ORDER
(SORTED).
1TOUCH SPD DIAL LIST 2 (Detailed List)
27/12 2002 17:23 FAX 123 4567
CANON
001
27/12 2002 17:23***********************************
FAX 123 4567
CANON
*** 1-TOUCH SPD DIAL LIST 2 ***
001
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
[
01]
CONNECTION TEL
CONNECTION ID
TX TYPE
[
03]
CONNECTION TEL
GROUP DIAL
CONNECTION ID
CONNECTION ID
GROUP 2
[
905 795 1111
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
1-TOUCH SPD DIAL LIST 2
Canon CANADA
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
REGULAR TX
12] CONNECTION TEL
TX TYPE
[
04]
CONNECTION TEL
2 50921
[
01] CONNECTION
TEL
CONNECTION ID
Canon ITALIA
CONNECTION
ID
TX TYPE
REGULAR TX
905 795 1111
Canon CANADA
REGULAR TX
GROUP DIAL
Canon GROUP 2
TX TYPE
[
05]
CONNECTION TEL
1 432 2060
[
03] CONNECTION
TEL
CONNECTION ID
Canon OPTICS
CONNECTION
ID
TX TYPE
PSWD/SUBADD.
SUBADDRESS
1323
[
12]
CONNECTION TEL
TX TYPE 2 887 0166
REGULAR TX
CONNECTION ID
Canon AUSTRALIA
TX TYPE
REGULAR
[
05] CONNECTION
TEL TX
1 432 2060
[
04] CONNECTION TEL
CONNECTION ID
CONNECTION ID
TX TYPE
SUBADDRES
IF YOU PRESS # IN STEP 7
(
p. 6-17), THE DESTINATIONS ARE
LISTED IN BUTTON ORDER
(UNSORTED).
618
2 887 0166
Canon AUSTRALIA
REGULAR TX
Speed Dialling
2 50921
Canon ITALIA
Canon OPTICS
PSWD/SUBADD.
1323
IF YOU PRESS
IN STEP 7
(
p. 6-17), THE DESTINATIONS ARE
LISTED IN ALPHABETICAL ORDER
(SORTED).
Chapter 6
■
CODED SPEED DIAL LIST 1
27/12 2002 17:23 FAX 123 4567
CANON
001
***********************************
27/12 2002 17:23 FAX
123 4567
CANON
*** CODED SPEED DIAL LIST 1 ***
***********************************
001
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
NO.
[*
[*
[*
[*
[*
[*
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
CONNECTION
ID
CODED SPEED
DIAL LISTTX
1 TYPE
CONNECTION TEL
00]
01]
02]
03]
21]
32]
2131 1250
03 3758 2111
1 49 39 25 25
NO.
516p488 6700
[
00]
GROUP DIAL
[
02]
81 773 3173
[
[
[
[
21]
01]
03]
32]
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
Canon DEUTSCH.
Canon TOKYO
CONNECTION
TEL FRANCE
Canon
2131 1250
1 49 39 25 25
GROUP DIAL
03 3758 2111
516p488 6700
81 773 3173
Canon U.S.A.
Canon GROUP 1
Canon UK
TX TYPE
REGULAR TX
Canon DEUTSCH.
Canon
FRANCE
PSWD/SUBADD.
Canon GROUP 1
Canon TOKYO
Canon U.S.A.
Canon UK
REGULAR TX
REGULAR TX
REGULAR TX
REGULAR TX
PSWD/SUBADD.
IF YOU PRESS
IN STEP 7
(
p. 6-17), THE DESTINATIONS ARE
LISTED IN ALPHABETICAL ORDER
(SORTED).
IF YOU PRESS # IN STEP 7
(
p. 6-17), THE DESTINATIONS ARE
LISTED IN CODE ORDER
(UNSORTED).
CODED SPEED DIAL LIST 2 (Detailed List)
27/12 2002 17:23 FAX 123 4567
CANON
***********************************
27/12 2002 17:23 FAX
123 4567
CANON
*** CODED SPEED DIAL LIST 2 ***
***********************************
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
[*
00]
CONNECTION TEL
CONNECTION ID
TX TYPE
[*
01]
[
00]TELCONNECTION
TEL2111
CONNECTION
03 3758
IDTOKYO
CONNECTION ID CONNECTION
Canon
TX TYPE REGULAR TX
TX TYPE
2131 1250
Canon DEUTSCH.
REGULAR TX
[*
02]
[
02]TELCONNECTION
TEL
CONNECTION
1 49 39
25 25
IDFRANCE
CONNECTION ID CONNECTION
Canon
TX TYPE REGULAR TX
TX TYPE
1 49 39 25 25
Canon FRANCE
REGULAR TX
[*
03]
[
21]TELCONNECTION
TEL6700
CONNECTION
516p488
IDU.S.A.
CONNECTION ID CONNECTION
Canon
TX TYPE
REGULAR TX
GROUP DIAL
Canon GROUP 1
21]
[*
32]
01] CONNECTION TEL
CONNECTION
ID DIAL
CONNECTION TEL
GROUP
CONNECTION ID TX TYPE Canon GROUP 1
03 3758 2111
Canon TOKYO
REGULAR TX
[
03]TELCONNECTION
TEL
CONNECTION
81 773
3173
IDUK
CONNECTION ID CONNECTION
Canon
TX TYPE PSWD/SUBADD.
TX TYPE
SUBADDRESS
1323
516p488 6700
Canon U.S.A.
REGULAR TX
[
32] CONNECTION TEL
CONNECTION ID
TX TYPE
SUBADDRES
IF YOU PRESS # IN STEP 7
(
p. 6-17), THE DESTINATIONS ARE
LISTED IN CODE ORDER
(UNSORTED).
Chapter 6
001
2131 1250
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
CODED SPEED DIAL LIST 2
Canon DEUTSCH.
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
REGULAR TX
[
[*
001
81 773 3173
Canon UK
PSWD/SUBADD.
1323
IF YOU PRESS
IN STEP 7
(
p. 6-17), THE DESTINATIONS ARE
LISTED IN ALPHABETICAL ORDER
(SORTED).
Speed Dialling
Speed Dialling
■
REGULAR TX
REGULAR TX
CONNECTION
REGULAR TX ID
619
■
GROUP DIAL LIST
27/12 2002 17:23 FAX 123 4567
CANON
001
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
GROUP DIAL LIST
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
620
[
03] Canon GROUP 2
[
[
[
[
04]
00]
02]
32]
[
21] Canon GROUP 1
[
[
01] 905 795 1111
03] 516p488 6700
Speed Dialling
2 50921
2131 1250
1 49 39 25 25
81 773 3173
Canon ITALIA
Canon DEUTSCH.
Canon FRANCE
Canon UK
Canon CANADA
Canon U.S.A.
Chapter 6
Chapter 7
❏
Preparing to Send a Fax .............................................................................
• Documents You Can Fax.......................................................................
• Setting the Scanning Resolution ............................................................
• Setting the Scanning Contrast................................................................
• Dialling Methods ...................................................................................
72
72
72
73
74
❏
Sending Methods........................................................................................
• Memory Sending ...................................................................................
• Manual Sending Via the Handset ..........................................................
75
75
76
❏
Cancelling Sending ....................................................................................
78
❏
Redialling When the Line is Busy .............................................................
• Manual Redialling .................................................................................
Cancelling Manual Redialling ............................................................
• Automatic Redialling.............................................................................
What is Automatic Redialling?...........................................................
Cancelling Automatic Redialling........................................................
Setting the Options for Automatic Redialling ....................................
79
79
79
79
79
79
710
❏
Sending the Same Document to Several Fax Numbers
(Sequential Broadcasting) ..........................................................................
712
❏
Delayed Sending ........................................................................................
• Scanning a Document into Memory for Delayed Sending ....................
• Printing a Document Set for Delayed Sending......................................
• Deleting a Document Set for Delayed Sending .....................................
714
714
716
717
Sending Faxes
71
Sending Faxes
Chapter 7
Sending Faxes
Preparing to Send a Fax
Documents You Can Fax
For information on the types of documents you can fax, their requirements, and
details on loading documents, see Chapter 4.
Setting the Scanning Resolution
You can set the scanning resolution of documents you send. The higher the resolution
the higher the output quality at the other end, but the slower the transmission speed.
Adjust the scanning resolution according to the type of document you are sending.
If you are sending a document that requires some pages to be scanned at a different
resolution from the others, you can change the resolution setting while the document
is being scanned. However, please note that the new setting will only be effective
from the next page scanned.
Follow this procedure to set the scanning resolution:
1
Press Resolution to select the resolution
setting you want.
•
2
72
Ex:
FAX PHOTO
You can select from the following:
– FAX STANDARD
Suitable for most textonly documents.
– FAX FINE
Suitable for fineprint documents.
– FAX PHOTO
Suitable for documents that contain images such as photos. With this
setting, areas of the document that contain photos are automatically
scanned with 64 levels of grey, rather than just in black & white.
– SUPER FINE
Suitable for documents that contain fine print and images. This setting
is four times the resolution of the FAX STANDARD setting.
Continue with the operation you are performing.
• If you do not proceed with any other operation, the LCD returns to
standby mode after about 10 seconds.
Sending Faxes
Chapter 7
You can adjust the degree of contrast at which your document is scanned for sending
and copying. Adjust according to how light or how dark your document is.
Follow this procedure to set the scanning contrast for sending and copying:
1
Press Function.
2
Press Data Registration.
3
Press OK twice.
DATA REGSTRATION
USER SETTINGS
DATE & TIME
Chapter 7
4
Use
5
Press OK.
6
Use
or
to select the scanning contrast
you want.
• You can select from the following:
– STANDARD
Suitable for most documents.
– DARKER
Suitable for light documents.
– LIGHTER
Suitable for dark documents.
7
Press OK.
8
Press Stop to return to standby mode.
or
to select SCAN CONTRAST.
SCAN CONTRAST
Ex:
STANDARD
OFFHOOK ALARM
Ex:
15:00
FaxOnly
Sending Faxes
73
Sending Faxes
Setting the Scanning Contrast
Dialling Methods
There are several ways of dialling the fax number(s) you want to send to. They are as
follows:
74
•
Regular Dialling
Dial a fax number by using the numeric buttons, similar to dialling a telephone
number.
•
OneTouch Speed Dialling
Dial a fax number by pressing the onetouch speed dialling button (01 to 15)
assigned to the fax number. For details on registering and using onetouch speed
dialling, see pp. 63, 614.
•
Coded Speed Dialling
Dial a fax number by pressing Coded Dial and entering the twodigit code
(00 to 99) assigned to the fax number. For details on registering and using coded
speed dialling, see pp. 67, 614.
•
Group Dialling
Send a document to a predefined group of fax numbers registered for speed
dialling. For details on registering groups and using group dialling, see pp. 611,
614.
•
Dialling with the Directory
Look up the other party’s name by using the directory function. For details on
using the directory function, see p. 616.
Sending Faxes
Chapter 7
This section explains the two main sending methods: Memory sending and Manual
sending via the handset.
Memory Sending
Memory sending is a quick and easy way to send a document. As the FAX scans the
first page of a multipage document into its memory, it begins calling the other party
and transmitting the information even as the remaining pages are being scanned.
Since the FAX is multitasking, you can even scan a document into memory while
performing other tasks.
The FAX has enough memory to store up to approximately 448 pages* (FAXL295)
/ 350 pages* (FAXL220) (fewer if the document contains many graphics or
particularly dense text).
Follow this procedure to send a document using memory sending:
1
Load the document, face down in the ADF
( p. 43).
•
•
2
•
*
Chapter 7
MEMORY USED 0%
(Currently used memory)
To adjust the resolution and contrast,
see pp. 72, 73.
You may be unable to send if the memory
used (shown in the LCD) is close to
100%. Use manual sending via the
handset instead ( p. 76).
Dial the other party’s fax number.
•
•
Ex:
DOCUMENT READY
(Standby to scan)
Ex:
TEL=
9p7654321
For dialling methods, see p. 74.
If you enter the wrong number, press
Stop, then enter the correct number.
If you are connected to a PBX and need
to first dial an outside line access number
(“9”, for example), add a pause after that
number by pressing Redial/Pause
( p. 92).
Based on Canon FAX Standard Chart No. 1, standard mode.
Sending Faxes
75
Sending Faxes
Sending Methods
3
Press Start/Copy to begin scanning for sending, or if you used speed dialling,
wait a few seconds for the FAX to begin scanning automatically.
•
•
•
•
•
If you do not want the FAX to begin scanning automatically after a few
seconds, disable the TIME OUT setting ( p. 146).
To cancel sending once dialling has started, press Stop then
( p. 78).
If the number you are calling is busy, the FAX redials the number
automatically after a few minutes ( p. 79).
You can register up to 20 different sending operations for memory sending.
The document is automatically deleted from memory after sending. This occurs even
if an error prevents complete transmission of the document.
Manual Sending Via the Handset
Manual sending via the handset allows you to talk to the other party before sending a
document. This method is useful if the other party must manually activate their fax
machine to receive a fax.
For this mode, you need to connect the optional handset or a telephone to your FAX
( p. 25).
Follow this procedure to send a document using manual sending via the handset:
1
Make sure you have connected the optional
handset or a telephone to the FAX
( p. 25).
2
Load the document, face down in the ADF
( p. 43).
•
To adjust the resolution and contrast,
see pp. 72, 73.
Ex:
MEMORY USED 0%
(Currently used memory)
DOCUMENT READY
(Standby to scan)
3
Press Hook.
•
76
Sending Faxes
TEL=
You can also lift the handset instead of
pressing Hook.
Chapter 7
Dial the other party’s fax/telephone number.
•
•
TEL=
7654321
For dialling methods, see p. 74.
If you make a mistake during dialling,
press Hook or hang up the handset and
start again from step 3.
■
If you hear a highpitched signal instead of a voice:
5
Press Start/Copy to begin sending the document.
If you picked up the handset to dial, press Start/Copy and hang up.
■
If you hear a voice:
5
Pick up the handset and start your conversation.
•
If you pressed Hook instead of lifting the handset in step 3, you will hear
the other party’s voice but they will not be able to hear you through the
speaker. Pick up the handset to talk to the other party.
6
When you are ready to send your document, ask the other party to press the
start button on their fax machine.
7
When you hear the highpitched signal of the other party’s fax machine, press
Start/Copy and hang up to begin sending the document.
•
If using the handset, be sure to hang up after you press Start/Copy on the FAX,
otherwise the call will be disconnected.
The FAX will alert you by beeping if the handset is not hung up properly. Make sure
the handset is seated properly in its cradle. If you do not want the FAX to beep, disable
the OFFHOOK ALARM setting ( p. 144).
•
Chapter 7
Ex:
Sending Faxes
77
Sending Faxes
4
Cancelling Sending
Follow this procedure if you want to stop sending a document before transmission is
completed:
■
1
If you are sending a document using manual sending via the
handset:
Press Stop.
•
•
The transmission is cancelled.
The FAX prints an ERROR TX
REPORT ( p. 114).
■
If you are sending a document using memory sending:
1
Press Stop.
•
2
The FAX asks you to confirm that you
want to cancel sending.
Press
•
•
•
•
CANCEL?
YES #NO
YES=( ) NO=(#)
to cancel sending.
Sending is not cancelled until you
press .
If you change your mind and want to
continue sending, press #.
To cancel transmission of a document
waiting to be sent (e.g. delayed sending,
between rediallings), you will have to
delete it from memory ( pp. 717, 98).
The FAX prints an ERROR TX
REPORT ( p. 114).
When you cancel sending, you may need to open the operation panel to remove the
document from the ADF ( p. 132).
78
Sending Faxes
Chapter 7
There are two methods of redialling: Manual redialling and Automatic redialling.
This section explains these two methods.
Manual Redialling
Press Redial/Pause to dial the last number you dialled with the numeric buttons.
(This starts redialling regardless of whether automatic redialling is enabled.)
Cancelling Manual Redialling
To cancel manual redialling, press Stop.
Automatic Redialling
What is Automatic Redialling?
When you are sending a document using memory sending ( p. 75) and the other
party’s line is busy, the FAX waits the specified time interval and then redials the
number automatically. This is called Automatic redialling.
You will know that the FAX is waiting to redial when AUTO REDIAL and the
transaction number (TX/RX NO.) are displayed in the LCD.
The automatic redialling options allow you to customise the number of times the
FAX redials, as well as the time interval between redials. You can also disable
automatic redialling if you prefer the FAX not to do so.
If all automatic redialling attempts are unsuccessful, the FAX cancels the
transmission and prints an ERROR TX REPORT to notify you that the transmission
was not completed ( p. 114).
Cancelling Automatic Redialling
Automatic redialling cannot be cancelled with the Stop button while the FAX is
waiting to redial. You can either wait until the FAX begins redialling and then follow
the procedure below, or if you want to cancel while the FAX is waiting to redial, you
will have to delete the document from memory ( p. 98).
Follow this procedure to cancel automatic redialling when the FAX begins redialling:
1
Chapter 7
Wait until the FAX begins redialling.
DIALLING
Sending Faxes
79
Sending Faxes
Redialling When the Line is Busy
2
Press Stop.
•
3
Press
•
•
•
CANCEL?
The FAX asks you to confirm that you
want to cancel automatic redialling.
YES #NO
YES=( ) NO=(#)
to cancel redialling.
Redialling is not cancelled until you press .
If you change your mind and want to continue redialling, press #.
The FAX prints an ERROR TX REPORT ( p. 114).
Setting the Options for Automatic Redialling
You can set the following options for automatic redialling:
•
•
•
Whether the FAX redials automatically.
The number of times the FAX attempts to redial.
The time interval between redialling attempts.
Follow this procedure to adjust the automatic redialling options:
710
1
Press Function.
2
Press Data Registration.
3
Press OK.
4
Use ▼ or ▲ to select TX SETTINGS.
5
Press OK.
6
Use ▼ or ▲ to select AUTO REDIAL.
7
Press OK.
Sending Faxes
DATA REGSTRATION
USER SETTINGS
TX SETTINGS
ECM TX
AUTO REDIAL
Ex:
ON
Chapter 7
Use ▼ or ▲ to select the setting you want.
•
Sending Faxes
8
You can select from the following:
– ON
Enables automatic redialling.
– OFF
Disables automatic redialling.
■
If you selected OFF in step 8:
9
Press OK.
10 Press Stop to return to standby mode.
■
If you selected ON in step 8:
9
Press OK twice.
TIME OUT
Ex:
15:00
REDIAL TIMES
Ex:
10 Use the numeric buttons to enter the number
2TIMES
Ex:
5TIMES
of times you want the FAX to redial.
•
FaxOnly
You can select from 1 to 10 times.*
11 Press OK twice.
REDIAL INTERVAL
Ex:
12 Use the numeric buttons to enter the time
2MIN.
Ex:
5MIN.
interval between redials.
•
You can select from 2 to 99 minutes.*
13 Press OK.
14 Press Stop to return to standby mode.
*
Chapter 7
TIME OUT
Ex:
15:00
FaxOnly
The selectable values vary depending on the country.
Sending Faxes
711
Sending the Same Document to Several Fax
Numbers (Sequential Broadcasting)
This feature, also called Sequential Broadcasting, allows you to send the same
document to several fax numbers in one operation. Simply load the document, enter
the fax numbers, and the FAX will then scan the document into its memory and send
the document to all the fax numbers you entered, one after the other.
You can send the same document to as many as 116 fax numbers using this feature.
Please note, however, that the fax numbers you enter must be registered for onetouch
or coded speed dialling ( Chapter 6). You will only be able to enter one fax number
using regular dialling (i.e. with the numeric buttons).
If you frequently send documents to the same group of fax numbers, you can register
these numbers for group dialling instead. This will simplify dialling ( p. 611).
Follow this procedure to send the same document to several fax numbers:
1
Load the document, face down in the ADF
( p. 43).
•
•
2
MEMORY USED 0%
(Currently used memory)
To adjust the resolution and contrast,
see pp. 72, 73.
You may be unable to send if the memory
used (shown in the LCD) is close to
100%. To free up space in the FAX’s
memory: print, send, or delete any
documents you no longer need to be
stored in memory ( p. 94).
DOCUMENT READY
(Standby to scan)
Enter up to 116 fax numbers using any of the
following methods:
❏
❏
712
Ex:
Sending Faxes
Onetouch speed dialling:
Press the onetouch speed dialling
button(s) you want.
Coded speed dialling:
Press Coded Dial, then use the numeric
buttons to enter the twodigit code you
want. Repeat for other codes.
• Be sure to press Coded Dial before
each code.
Ex:
Ex:
Ex:
TEL=905 795 1111
01
TEL=03 3758 2111
Chapter 7
❏
•
•
•
•
3
•
Chapter 7
TEL=
2 887 0166
Press Start/Copy to begin scanning for sending, or wait a few seconds for the
FAX to begin scanning automatically.
•
•
Ex:
You can enter the fax numbers in any order.
If you enter a wrong destination, press C, then enter the correct destination.
You must enter the second destination within five seconds of entering the first one. All
subsequent destinations must be entered within 10 seconds. If you wait longer than
these times, the FAX automatically begins scanning the document for sending. If you
do not want the FAX to begin scanning automatically after a few seconds, disable the
TIME OUT setting ( p. 146).
To review the destinations entered, use ▼ or ▲ to scroll through the numbers.
•
•
Regular dialling:
Use the numeric buttons to enter the fax
number you want, then press OK.
• You can only enter one fax number
this way.
Dialling with the directory:
Look up the other party’s name.
The FAX will first send the document to the onetouch speed dialling
destinations, then the coded speed dialling destinations, and finally to the
destination dialled using regular dialling.
If you do not want the FAX to begin scanning automatically after a few
seconds, disable the TIME OUT setting ( p. 146).
To cancel sending once dialling has started, press Stop then . Sending
to all destinations you specified in step 2 will be cancelled. (You cannot
cancel only one destination.)
If a number is busy, the FAX will continue sending to the other destinations and then
automatically redial the number that was busy.
If the FAX’s memory becomes full while scanning your document, MEMORY FULL
will appear in the LCD. If this happens, remove the remainder of the document from
the ADF (you may need to open the operation panel to do so), then divide the
document into several sections and send each section separately.
Sending Faxes
713
Sending Faxes
❏
Delayed Sending
Your FAX allows you to scan a document into its memory and send it automatically
to as many as 116 fax numbers at a preset time within the next 24 hours. This is called
Delayed sending or Timer sending. By using this feature, you can take advantage of
lower long distance rates at night, for example.
To use delayed sending correctly, make sure the correct time is set on your FAX
( p. 36).
Scanning a Document into Memory for Delayed
Sending
Follow this procedure to scan a document into the FAX’s memory for delayed
sending:
1
Load the document, face down in the ADF
( p. 43).
• To adjust the resolution and contrast,
see pp. 72, 73.
• You may be unable to scan if the memory
used (shown in the LCD) is close to
100%. To free up space in the FAX’s
memory: print, send, or delete any
documents you no longer need to be
stored in memory ( p. 94).
Ex:
MEMORY USED 0%
(Currently used memory)
DOCUMENT READY
(Standby to scan)
2
Press Function.
3
Press Delayed Transmission.
4
Press OK.
Ex:
5
Use the numeric buttons to enter the time at
which you want to send the document.
• Use the 24hour format for the time (e.g.
11:30 p.m. as 23:30), and precede single
digits with a zero.
Ex:
6
Press OK.
REGISTER
SET TIME
1
_5:00
SET TIME
2
_2:30
SELECT LOCATIONS
TEL=
714
Sending Faxes
Chapter 7
Enter up to 116 fax numbers you want to send
to using any of the following methods:
❏
❏
❏
❏
Ex:
Ex:
Ex:
Ex:
TEL=905 795 1111
01
TEL=03 3758 2111
TEL=
2 887 0166
•
•
If you enter the wrong destination, press C, then enter the correct destination.
When you have entered multiple fax numbers, use ▼ or ▲ to scroll through the
numbers to review the destinations.
8
Press Start/Copy to begin scanning the
document into the FAX’s memory.
• When the preset time is reached, the FAX
sends the document to the destination(s)
you specified in step 7.
•
•
You can register up to 20 different delayed sending operations.
If the FAX’s memory becomes full while scanning your document, MEMORY FULL
will appear in the LCD. If this happens, you will not be able to send the document at
a preset time. Remove the remainder of the document from the ADF (you may need
to open the operation panel to do so).
Since the FAX is multitasking, you can perform other tasks even when your FAX is
set for delayed sending.
•
Chapter 7
Onetouch speed dialling:
Press the onetouch speed dialling
button(s) you want.
Coded speed dialling:
Press Coded Dial, then use the numeric
buttons to enter the twodigit code you
want. Repeat for other codes.
• Be sure to press Coded Dial before
each code.
Regular dialling:
Use the numeric buttons to enter the fax
number you want, then press OK.
• You can only enter one fax number
this way.
Dialling with the directory
Look up the other party’s name.
Sending Faxes
715
Sending Faxes
7
Printing a Document Set for Delayed Sending
Follow this procedure to print a document stored in memory for delayed sending:
When you print a document stored in memory for delayed sending using the
following procedure, the print is reduced to 90% of the original.
1
Press Function.
2
Press Delayed Transmission.
3
Use
4
Press OK.
Ex:
5
Use
or
to select the transaction number
(TX/RX NO.) of the document you want to
print.
• If you are unsure of the transaction
number (TX/RX NO.), print the DOC.
MEMORY LIST ( p. 94).
• A “#” before the transaction number
(TX/RX NO.) indicates that that
document is being sent at that moment
and can therefore not be selected.
• Use
or
to display details of the
transaction (e.g. destination).
Ex:
6
Press OK.
or
REGISTER
to select PRINT.
PRINT
TX/RX NO.
0
_001
TX/RX NO.
#0
_003
1ST PG ONLY?
YES=( ) NO=(#)
716
7
Press to print the first page only, or press #
to print all pages of the document.
• The FAX prints the document.
8
To continue printing other documents set for
delayed sending, repeat the procedure from
step 5.
or
Press Stop to return to standby mode.
Sending Faxes
Ex:
15:00
FaxOnly
Chapter 7
Follow this procedure to delete a document stored in memory for delayed sending:
1
Press Function.
2
Press Delayed Transmission.
3
Use
4
Press OK.
Ex:
5
Use
or
to select the transaction number
(TX/RX NO.) of the document you want to
delete.
• If you are unsure of the transaction
number (TX/RX NO.), print the DOC.
MEMORY LIST ( p. 94).
• A “#” before the transaction number
(TX/RX NO.) indicates that that
document is being sent at that moment. If
you want to delete a document being
sent, follow the instructions in the LCD.
• Use
or to display details of the
transaction (e.g. destination).
Ex:
6
Press OK.
or
REGISTER
to select DELETE FILE.
DELETE FILE
TX/RX NO.
0
_001
TX/RX NO.
#0
_003
OK TO DELETE?
YES=( ) NO=(#)
Chapter 7
7
Press to delete the document.
• If you change your mind and want to
keep the document in memory for
delayed sending, press #.
8
To continue deleting other documents set for
delayed sending, repeat the procedure from
step 5.
or
Press Stop to return to standby mode.
ERASING END
Ex:
15:00
FaxOnly
Sending Faxes
717
Sending Faxes
Deleting a Document Set for Delayed Sending
718
Sending Faxes
Chapter 7
Chapter 8
Receiving Faxes
Chapter 8
Receiving Methods ....................................................................................
• Receiving Faxes Automatically: FAX ONLY MODE ..........................
Setting FAX ONLY MODE ...............................................................
• Receiving Both Faxes and Telephone Calls Automatically:
Fax/Tel Mode.........................................................................................
Setting Fax/Tel Mode .........................................................................
Setting the Options for Fax/Tel Mode ................................................
• Receiving Faxes Manually: MANUAL MODE ....................................
Setting MANUAL MODE..................................................................
Receiving a Fax Manually ..................................................................
• Receiving With an Answering Machine: ANS.MACHINE MODE .....
Setting ANS.MACHINE MODE........................................................
Using the FAX With an Answering Machine.....................................
82
82
82
84
84
85
87
87
87
89
89
89
❏
Receiving While Performing Other Tasks .................................................
810
❏
Receiving Faxes in Memory When a Problem Occurs ..............................
810
❏
Cancelling Receiving .................................................................................
811
Receiving Faxes
81
Receiving Faxes
❏
Receiving Methods
The FAX provides you with several modes for receiving faxes. To determine which
mode best suits your requirements, refer to the table below:
Receive Mode
Main Use Operation
Requirements
Details
FAX ONLY
MODE
Fax
The FAX answers all
calls as fax calls. It
receives faxes
automatically and
disconnects voice calls.
Separate telephone line
for fax use only.
p. 82
Fax/Tel Mode
Fax/Tel
Optional handset or
The FAX automatically
switches between fax and telephone connected to
the FAX.
voice calls. It receives
faxes automatically and
rings for voice calls.
p. 84
MANUAL MODE
Tel
The FAX rings for every Optional handset or
call, whether a fax call or telephone connected to
the FAX.
a voice call. For a fax
call, you have to
manually activate
reception of a fax.
p. 87
ANS.MACHINE
MODE
Fax/Tel
Answering machine
The FAX receives
documents automatically connected to the FAX.
and the answering
machine records voice
messages.
p. 89
Once you have decided which mode is suitable for your needs, set the mode as
described in this chapter. You can change the mode at any time.
Receiving Faxes Automatically: FAX ONLY MODE
If you have a separate telephone line for fax use only, connect your FAX to this line
and set FAX ONLY MODE. Your FAX will answer all calls as fax calls.
Setting FAX ONLY MODE
1
Press Function then Receive Mode.
2
Use
or
press OK.
to select FAX ONLY MODE then
FAX ONLY MODE
Ex:
82
Receiving Faxes
15:00
FaxOnly
Chapter 8
If FAX ONLY MODE does not appear in the LCD when you press Receive Mode,
follow this procedure to set this mode:
1
Press Function.
2
Press Data Registration.
3
Press OK.
4
Use
5
Press OK.
6
Use
7
Press OK.
8
Use
9
Press OK.
or
or
USER SETTINGS
to select RX SETTINGS.
RX SETTINGS
ECM RX
to select RX MODE.
RX MODE
Ex:
to select FAX ONLY MODE.
INCOMING RING
Ex:
11 Confirm that FaxOnly is displayed in the
Ex:
LCD.
FAX/TEL AUTO SW
FAX ONLY MODE
10 Press Stop to return to standby mode.
•
Receiving Faxes
or
DATA REGSTRATION
15:00
FaxOnly
15:00
FaxOnly
If FaxOnly is not displayed, follow
steps 1 to 2 on page 82 to select FAX
ONLY MODE. After a few seconds, the
LCD returns to standby mode.
The FAX treats all incoming calls as fax calls. It receives faxes automatically and
disconnects any voice calls.
The FAX does not ring when it receives a fax call. If you want to be alerted when a
fax call is received, connect the optional handset or a telephone to the FAX, and
enable the INCOMING RING setting ( p. 147). You can also select the number of
rings before the FAX answers ( RING COUNT, p. 147).
Chapter 8
Receiving Faxes
83
Receiving Both Faxes and Telephone Calls
Automatically: Fax/Tel Mode
Set this mode if you only have one telephone line for fax and telephone use and want
your FAX to automatically switch between fax and voice calls.
For this mode, you need to connect the optional handset or a telephone to your FAX
( p. 25).
Setting Fax/Tel Mode
Follow this procedure to set the receive mode to FAX/TEL AUTO SW (Fax/
Tel Mode):
1
2
Press Function.
3
Press OK.
4
Use
5
Press OK.
6
Use
7
Press OK.
8
Use
9
Press OK.
Press Data Registration.
•
or
or
or
USER SETTINGS
to select RX SETTINGS.
RX SETTINGS
ECM RX
to select RX MODE.
RX MODE
Ex:
to select FAX/TEL AUTO SW.
FAX ONLY MODE
FAX/TEL AUTO SW
RING START TIME
To set the options for FAX/TEL AUTO
SW (Fax/Tel Mode), see the following
pages.
10 Press Stop to return to standby mode.
Ex:
11 Confirm that FaxTel is displayed in the
Ex:
LCD.
• If FaxTel is not displayed, follow steps
1 to 2 on page 82 to select Fax/Tel
Mode. After a few seconds, the LCD
returns to standby mode.
84
DATA REGSTRATION
Receiving Faxes
15:00
FaxTel
15:00
FaxTel
Chapter 8
Setting the Options for Fax/Tel Mode
■ What Happens When Fax/Tel Mode is Selected
When the FAX receives a call, it responds according to the type of call as follows:
Type of call
Telephone charges
begin for the caller.
Telephone
Fax
Fax
Sending document
manually
Sending document
automatically
The FAX answers without ringing.
The FAX listens for the fax tone.
(For 8 sec.)
RING START
TIME
The fax tone is
detected.
(Default setting = 8 sec.)
The document is
received automatically.
(The fax tone is
detected and the FAX
switches to receive
mode.)
The fax tone is not detected.
Pick up the handset
to talk.
The FAX starts ringing.
F/T RING TIME
(Default setting = 22 sec.)
If you don’t pick up the handset.
(within 22 sec.)
DEFAULT ACTION
Choose between:
RECEIVE (default setting) and DISCONNECT.
DISCONNECT
The fax disconnects
the call.
RECEIVE
(Default setting)
Not all fax machines are capable of sending a fax tone. For those cases if you set
the DEFAULT ACTION to RECEIVE, the fax switches to receive mode
automatically and starts receiving the document. If no document comes in, it
disconnects the call after approximately 40 seconds.
Chapter 8
Receiving Faxes
85
Receiving Faxes
If you set Fax/Tel Mode, you can control precisely how the FAX handles incoming
calls by adjusting the following settings:
– RING START TIME setting: Adjust the time the FAX takes to check whether a
call is from a fax machine or from a telephone (default: 8 seconds).
– F/T RING TIME setting: Adjust the length of time the FAX rings when the call
is from a telephone (default: 22 seconds).
– DEFAULT ACTION setting: Set whether the FAX switches to receive mode or
disconnects the call after the ring time set in F/T RING TIME has elapsed
(default: switches to receive mode).
Follow this procedure to set the Fax/Tel Mode options:
1
Follow steps 1 to 9 on page 84.
2
Press OK.
Ex:
3
Use the numeric buttons to enter the RING
START TIME duration.
Ex:
•
•
4
RING START TIME
8SEC
9SEC
You can select from 0 to 30 seconds.*
See the previous page for details on this
setting.
Press OK twice.
F/T RING TIME
Ex:
5
Use the numeric buttons to enter the F/T
RING TIME duration.
•
•
6
22SEC
Ex:
30SEC
You can select from 10 to 60 seconds.*
See the previous page for details on this
setting.
Press OK twice.
DEFAULT ACTION
Ex:
7
Use or to select the DEFAULT ACTION
setting you want.
•
•
*
**
86
RECEIVE
You can select from the following:
– RECEIVE (Switch to receive mode)
– DISCONNECT (Disconnect the
call)**
See the previous page for details on this
setting.
8
Press OK.
9
Press Stop to return to standby mode.
INCOMING RING
Ex:
15:00
FaxTel
The selectable duration varies depending on the country.
DISCONNECT is available for certain countries only.
Receiving Faxes
Chapter 8
Receiving Faxes Manually: MANUAL MODE
For this mode, you will need to connect the optional handset or a telephone to your
FAX to be able to receive voice calls and also to manually activate reception of
documents. You can activate reception directly from your FAX, or if your telephone
is located away from your unit, you can dial the remote receiving ID on the telephone
to activate reception (this is called Remote reception).
Setting MANUAL MODE
Follow this procedure to set the receive mode to MANUAL MODE:
1
Press Function then Receive Mode.
2
Use
or
press OK.
to select MANUAL MODE then
MANUAL MODE
Ex:
15:00
Manual
15:00
Manual
Receiving a Fax Manually
Follow this procedure to receive a fax manually:
Chapter 8
1
Make sure Manual is displayed in the LCD.
2
Make sure you have connected the optional
handset or a telephone to the FAX
( p. 25).
3
When you hear the optional handset or
telephone ring, pick up the handset.
Ex:
Receiving Faxes
87
Receiving Faxes
Set this mode if you only have one telephone line that you use mainly for voice calls,
and only occasionally to receive faxes.
■
If you hear a beep tone or silence:
4
Someone is trying to send you a fax. Press Start/Copy on your FAX and hang
up to begin receiving the document.
•
■
If you hear a voice:
4
Start your conversation. If the caller wants to send a fax after talking to you,
ask them to press the start button on their fax machine.
5
When you hear a beep, press Start/Copy on your FAX and hang up to begin
receiving the document.
•
•
•
•
•
•
88
If you are using the telephone and it is located away from your unit, dial
25 (the default remote receiving ID) on your telephone and hang up.
If you are using the telephone and it is located away from your unit, dial
25 (the default remote receiving ID) on your telephone and hang up.
If using the handset, be sure to hang up after you press Start/Copy on the FAX,
otherwise the call will be disconnected.
The FAX will alert you by beeping if the handset is not hung up properly. Make sure
the handset is seated properly in its cradle. If you do not want the FAX to beep, disable
the OFFHOOK ALARM setting ( p. 144).
If you cannot activate reception from the telephone, check that the REMOTE RX
setting is enabled ( p. 147).
You can change the remote receiving ID ( REMOTE RX ID, p. 147), or disable
remote receiving ( REMOTE RX, p. 147).
If you have an answering machine connected to your FAX that can carry out remote
control operations (controlling your answering machine from a remote telephone), the
security code for this function may be the same as the remote receiving ID of your
FAX. If this is the case, make sure you change the FAX’s remote receiving ID to make
it distinct from the answering machine’s security code ( REMOTE RX ID, p. 147).
Receiving Faxes
Chapter 8
Receiving With an Answering Machine:
ANS.MACHINE MODE
Connecting an answering machine to the FAX allows you to receive faxes and
telephone messages while you are out.
Setting ANS.MACHINE MODE
For this mode, you need to connect an answering machine or a telephone with an answering
machine to your FAX ( p. 25).
Follow this procedure to set the receive mode to ANS.MACHINE MODE:
1
Press Function then Receive Mode.
2
Use or to select ANS.MACHINE MODE
then press OK.
ANS.MACHINE MODE
Ex:
15:00
AnsMode
Using the FAX With an Answering Machine
Follow these guidelines when using the FAX with an answering machine:
• Set the answering machine to answer on the first or second ring.
• When recording the outgoing message on the answering machine:
– the entire message must be no longer than 15 seconds.
– in the message, tell your callers how to send a fax. For example: “Hello. I can’t
answer the phone right now, but please leave a message after the beep. If you
would like to send a fax, press the start button on your fax machine after you
finish your message. Thank you.”
Chapter 8
Receiving Faxes
89
Receiving Faxes
In ANS.MACHINE MODE, the FAX allows the answering machine to answer
incoming calls, then listens for the fax tone and automatically receives the fax if it
detects this tone.
Receiving While Performing Other Tasks
The FAX is a multitasking device so it can receive faxes and voice calls while you
are performing other tasks.
If the FAX cannot print a received fax because it is performing another task that
prevents it from doing so, it will receive the fax in memory. Then, as soon as it
completes the other task, the FAX automatically prints the received fax from
memory.
Receiving Faxes in Memory When a Problem
Occurs
If the FAX encounters a problem when it is receiving a fax, it automatically stores the
unprinted pages of the fax in memory. It then displays REC’D IN MEMORY as well
as one or more messages in the LCD. For an explanation of the message(s) and details
on the action to take, see p. 138.
•
•
•
•
810
The FAX’s memory can store up to approximately 448 pages * (FAXL295) /
350 pages * (FAXL220).
You can set the unit so that it does not store faxes in memory if a problem occurs
during reception ( MEMORY RX, p. 147).
Once the problem is solved and the unit prints the received fax, it will delete the fax
from memory.
If the unit’s memory becomes full while receiving a fax in memory, you will not be
able to receive the remaining pages. Contact the other party and ask them to resend the
remainder of the fax.
Receiving Faxes
Chapter 8
Cancelling Receiving
Follow this procedure if you want to stop receiving a fax before reception is
completed:
Press Stop.
•
2
Press
•
•
CANCEL?
The FAX asks you to confirm that you
want to cancel receiving.
YES=( ) NO=(#)
to cancel receiving.
Receiving is not cancelled until you
press .
If you change your mind and want to
continue receiving, press #.
YES #NO
TX/RX CANCELLED
Ex:
TX/RX NO.
5003
* Based on Canon FAX Standard Chart No. 1, standard mode.
Chapter 8
Receiving Faxes
811
Receiving Faxes
1
812
Receiving Faxes
Chapter 8
Chapter 9
❏
Special Dialling..........................................................................................
• Entering Pauses in a Fax/Telephone Number........................................
• Switching Temporarily to Tone Dialling...............................................
• Dialling Through a Switchboard ...........................................................
92
92
93
93
❏
Documents Stored in Memory ...................................................................
• Printing a List of Documents Stored in Memory...................................
• Printing a Document Stored in Memory................................................
• Sending a Document Stored in Memory ...............................................
• Deleting a Document Stored in Memory...............................................
94
94
95
96
98
❏
Polling ........................................................................................................
• What is Polling?.....................................................................................
• Polling Receiving...................................................................................
Polling Another Fax Machine.............................................................
Cancelling Polling Receiving .............................................................
• Polling Sending......................................................................................
Setting Up the Polling Box .................................................................
Scanning a Document into the Polling Box........................................
Changing or Deleting the Polling Box Settings..................................
99
99
99
99
911
911
911
914
914
❏
Restricting Use of Your FAX ....................................................................
• Enabling Restriction of Your FAX........................................................
• Cancelling Restriction of Your FAX.....................................................
916
916
917
❏
Restricting Reception.................................................................................
919
Special Features
91
Special Features
Chapter 9
Special Features
Special Dialling
Entering Pauses in a Fax/Telephone Number
You may need to enter pauses in a fax/telephone number in the following situations:
– When you dial or register an overseas number. The length and position of the
pause depends on the telephone system of your country.
– When your FAX is connected to a switchboard. For details, see p. 39.
Follow this procedure to enter pauses during regular dialling or when registering a
number for speed dialling:
1
When you come to the step that requires you
to enter the fax/telephone number, use the
numeric buttons to enter the number up to
where a pause is necessary.
•
2
•
3
4
5
*
92
Ex:
TEL=
00P
Ex:
TEL=
00p811234
TEL=
00p811234P
If you enter the wrong number, press C
and start again from step 1.
To enter a pause at the end of the number,
press Redial/Pause.
•
00
A pause entered within a number (P) is
two seconds* long.
For a longer pause, press Redial/Pause
again for another twosecond* pause.
Alternatively, you can change the length
of the pause ( MID PAUSE SET,
p. 146).
Continue entering the rest of the fax/
telephone number with the numeric buttons.
•
TEL=
If you enter the wrong number, press C,
then enter the correct number.
Press Redial/Pause to enter a pause.
•
Ex:
Ex:
A pause at the end of a number (P) is
fixed to ten seconds.
Continue with the operation you are
performing.
The duration of a pause varies depending on the country.
Special Features
Chapter 9
Switching Temporarily to Tone Dialling
Many information services for banks, airline reservations, hotel reservations, etc.,
require tone dialling for their services. If your FAX is set for pulse dialling
( p. 38), follow this procedure to set the unit temporarily for tone dialling:
To talk to the other party, you will need to connect the optional handset or a telephone to
your FAX ( p. 25).
Press Hook.
•
2
Use the numeric buttons to dial the telephone
number of the information service.
•
3
•
4
5
TEL=
7654321
Ex:
TEL=
7654321T
TEL=
7654321T 34
When T( ) is pressed, T is displayed in
the LCD.
If you pressed Hook in step 1, you can
pick up the handset if you need to talk to
the other party.
Use the numeric buttons to enter the numbers
requested by the information service.
•
Ex:
The FAX connects using the pulses
required by your telephone line.
When the recorded message of the
information service answers, press T( ) to
switch to tone dialling.
•
TEL=
You can also lift the handset instead of
pressing Hook.
Ex:
Numbers entered after pressing T( )
will be dialled using tone dialling.
When you have finished, press Hook to
disconnect the call.
•
•
If you used the handset, hang up to
disconnect the call.
Tone dialling is cancelled when you
disconnect the call.
Dialling Through a Switchboard
For details on dialling through a switchboard, see p. 39.
Chapter 9
Special Features
93
Special Features
1
Documents Stored in Memory
This section describes how to perform different operations with documents stored in
memory. You will find instructions for printing a list of documents in memory, as
well as procedures for printing, sending, and deleting documents stored in memory.
Printing a List of Documents Stored in Memory
The FAX can print a list of documents stored in memory, along with the transaction
number (TX/RX NO.) of each document. Once you know the transaction number of
a document in memory, you can print it, send it, or delete it. These procedures are
described on the following pages.
Follow this procedure to print a list of documents stored in memory:
1
Press Function.
2
Press Memory Reference.
3
Press OK.
•
DOC. MEMORY LIST
PRINTING REPORT
The FAX prints the DOC. MEMORY
LIST.
27/12 2002 21:53 FAX 123 4567
CANON
001
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
DOC. MEMORY LIST
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
TX/RX NO
0046
0047
94
MODE
TRANSMIT
B’CAST
0048
DEL SQ BDCST
0049
0050
DELAYED TX
B’CAST
Special Features
CONNECTION TEL/ID
[
[
[
[
[
[
[
01]
01]
02]
04]
03]
05]
03]
Canon TOKYO
Canon CANADA
Canon FRANCE
Canon ITALIA
Canon U.S.A.
Canon OPTICS
Canon GROUP 2
PGS.
SET TIME
3 27/12
1 27/12
ST. TIME
21:24
21:36
1 27/12
21:39
2 27/12
1 27/12
21:45
21:49
23:00
23:00
23:00
Chapter 9
Printing a Document Stored in Memory
Follow this procedure to print a document stored in memory:
When you print a document stored in memory using the following procedure, the print is
reduced to 90% of the original.
1
Press Function.
2
Press Memory Reference.
3
Use
4
Press OK.
Ex:
5
Use
or
to select the transaction number
(TX/RX NO.) of the document you want to
print.
Ex:
•
•
6
to select PRINT DOCUMENT.
PRINT DOCUMENT
TX/RX NO.
0
_001
TX/RX NO.
#0
_003
If you are unsure of the transaction
number (TX/RX NO.), print the DOC.
MEMORY LIST ( p. 94).
A “#” before the transaction number
(TX/RX NO.) indicates that that
document is being sent at that moment
and can therefore not be selected.
Use
or to display details of the
transaction (e.g. destination).
Press OK.
1ST PG ONLY?
YES=( ) NO=(#)
Chapter 9
7
Press to print the first page only, or press #
to print all pages of the document.
• The FAX prints the document.
8
To continue printing other documents in
memory, repeat the procedure from step 5.
or
Press Stop to return to standby mode.
Ex:
15:00
FaxOnly
Special Features
95
Special Features
•
or
DOC. MEMORY LIST
Sending a Document Stored in Memory
Follow this procedure to send a document received in memory:
1
Press Function.
2
Press Memory Reference.
3
Use
4
Press OK.
Ex:
5
Use
or
to select the transaction number
(TX/RX NO.) of the document you want to
send.
Ex:
•
•
•
6
or
DOC. MEMORY LIST
to select RESEND DOCUMENT.
RESEND DOCUMENT
TX/RX NO.
0
_001
TX/RX NO.
#5
_003
If you are unsure of the transaction
number (TX/RX NO.), print the DOC.
MEMORY LIST ( p. 94).
A “#” before the transaction number
(TX/RX NO.) indicates that that
document is being sent or printed at that
moment, and can therefore not be
selected.
Use
or
to display details of the
transaction (e.g. destination).
Press OK.
SELECT LOCATIONS
TEL=
7
Enter up to 116 fax numbers you want to send
to using any of the following methods:
❏
❏
96
Onetouch speed dialling:
Press the onetouch speed dialling
button(s) you want.
Coded speed dialling:
Press Coded Dial, then use the numeric
buttons to enter the twodigit code you
want. Repeat for other codes.
• Be sure to press Coded Dial before
each code.
Special Features
Ex:
Ex:
Ex:
TEL=905 795 1111
01
TEL=03 3758 2111
Chapter 9
❏
Regular dialling:
Use the numeric buttons to enter the fax
number you want, then press OK.
• You can only enter one fax number this
way.
Ex:
TEL=
2 887 0166
•
•
If you enter a wrong destination, press C, then enter the correct destination.
To review the destinations entered, use
or
to scroll through the numbers.
8
Press OK to begin sending.
To cancel sending once dialling has
started, press Stop then . Sending to all
the destinations you specified in step 7
will be cancelled. (You cannot cancel
only one destination.)
Special Features
•
Chapter 9
Special Features
97
Deleting a Document Stored in Memory
Follow this procedure to delete a document stored in memory:
1
Press Function.
2
Press Memory Reference.
3
Use
4
Press OK.
Ex:
5
Use
or
to select the transaction number
(TX/RX NO.) of the document you want to
delete.
Ex:
•
•
•
6
98
DELETE DOCUMENT
TX/RX NO.
0
_001
TX/RX NO.
#0
_003
If you are unsure of the transaction
number (TX/RX NO.), print the DOC.
MEMORY LIST ( p. 94).
A “#” before the transaction number
(TX/RX NO.) indicates that that
document is being sent at that moment. If
you want to delete a document being
sent, follow the instructions in the LCD.
Use
or
to display details of the
transaction (e.g. destination).
OK TO DELETE
If you are deleting a document stored in
the polling box ( p. 911), enter the
password that restricts access to the
polling box settings, then press OK.
Press
•
8
to select DELETE DOCUMENT.
Press OK.
•
7
or
DOC. MEMORY LIST
YES=( ) NO=(#)
to delete the document.
ERASING END
If you change your mind and want to
keep the document in memory, press #.
To continue deleting other documents in
memory, repeat the procedure from step 5.
or
Press Stop to return to standby mode.
Special Features
Ex:
15:00
FaxOnly
Chapter 9
Polling
What is Polling?
In normal faxing, a fax machine sends a document to another fax machine. With
polling, a fax machine calls another fax machine and requests that a document be sent
to it; in other words, it “polls” that fax machine.
Your FAX has the capability of functioning in both roles; it can poll another fax
machine to retrieve a document from it (polling receiving), or it can hold a document
in its polling box so that other fax machines can poll your FAX and retrieve your
document (polling sending).
In polling receiving, your FAX calls another fax machine and requests it sends the
document it is holding.
You may find polling receiving convenient in the following situations:
– When you want to retrieve a document from an establishment, such as bank or
information service.
– When you want to retrieve a document from another fax machine at your
convenience.
– When you want to bear the transmission cost of receiving a document.
Polling Another Fax Machine
Before polling another fax machine, be sure to read the following:
• The FAX can only poll fax machines that support polling.
• The document you want to retrieve must be ready to be polled on the other
party’s fax machine. If necessary, call the other party to check.
• Call the other party and check if you require a subaddress and/or password to
retrieve the document from their fax machine. If you do, take note of them and
register them together with the fax number for speed dialling ( Chapter 6).
You can only poll with a subaddress/password by using speed dialling. If you do
not require a subaddress/password, you can retrieve the document without
having to enter these numbers.
• If the other party is using a Canon fax machine and their unit does not support
subaddress/password transactions, ask them to set the polling ID on their fax
machine to 255 or 11111111 binary.
• You can poll several fax machines in one operation. Each polling operation can
retrieve documents from as many as 116 fax numbers.
• The subaddress/password must be an ITUT standard subaddress/password.
Chapter 9
Special Features
99
Special Features
Polling Receiving
Follow this procedure to poll one or several fax machine(s):
1
Press Function.
2
Press Polling.
3
Use
4
Press OK.
5
Enter up to 116 fax numbers you want to poll
using any of the following methods:
❏
❏
❏
❏
•
•
•
6
910
or
POLLING TX
to select POLLING RX.
Onetouch speed dialling:
Press the onetouch speed dialling
button(s) you want.
Coded speed dialling:
Press Coded Dial, then use the numeric
buttons to enter the twodigit code you
want. Repeat for other codes.
• Be sure to press Coded Dial before
each code.
Regular dialling:
Use the numeric buttons to enter the fax
number you want, then press OK.
• You can only enter one fax number
this way.
Dialling with the directory
Look up the other party’s name.
POLLING RX
Ex:
Ex:
Ex:
Ex:
TEL=905 795 1111
01
TEL=03 3758 2111
TEL=
2 887 0166
If you enter a wrong destination, press C, then enter the correct destination.
You cannot enter a subaddress/password with regular dialling. If you need to enter a
subaddress/password for polling, register them together with the fax number for speed
dialling ( Chapter 6).
To review the destinations entered, use
or
to scroll through the numbers.
Press Start/Copy to begin polling the fax
machine(s).
Special Features
Chapter 9
Cancelling Polling Receiving
To cancel polling receiving, follow the same procedure as for cancelling receiving
( p. 811).
Polling Sending
In polling sending, your FAX holds a document in its polling box so that other fax
machines can retrieve it.
Setting Up the Polling Box
This section explains how to set up the FAX’s polling box so that you can scan a
document into it for other fax machines to retrieve it.
Before setting up the polling box, be sure to read the following:
• You can set an ITUT standard password for the polling box to restrict being
polled only by fax machines that have this exact password (see the instructions
that follow). Make sure you contact the other party to inform them of your
password. Do not set a password if the other party’s fax machine does not
support password transactions.
• Your FAX can be set to hold the document in its polling box until it is polled by
one fax machine, or it can be set to continue to hold it so that several fax
machines can retrieve the document (see below for details).
Follow this procedure to set up the polling box:
Chapter 9
1
Press Function.
2
Press Data Registration.
3
Press OK.
4
Use
or
DATA REGSTRATION
USER SETTINGS
to select POLLING BOX.
POLLING BOX
Special Features
911
Special Features
You may find polling sending convenient in the following situations:
– A company department might store a document in the FAX so that other
departments can retrieve it if they require that document.
– When you want the other party to retrieve a document from your FAX at their
convenience.
– When you want the other party to bear the transmission cost of receiving a
document from your FAX.
5
Press OK three times.
SETUP FILE
FILE NAME
6
Use the numeric buttons to enter a name for
the polling box (max. 24 characters, including
spaces).
•
7
Ex:
_
:A
Canon Dpt. 1_
:1
If you are unsure how to enter characters,
see p. 32.
Press OK twice.
DATA ENTRY OK
PASSWORD
PASSWORD
8
Use the numeric buttons to enter a fourdigit
password.
•
9
Press OK twice.
(max. 20 digits, including
•
•
PASSWORD
1
_234
This password prevents unauthorised
access to the polling box settings. You
will need to enter this password
whenever you want to change or delete
the polling box settings. If you do not
want to enter a password, ignore this step.
TX PASSWORD
10 Use the numeric buttons to enter a password
912
Ex:
_
, #, and spaces).
Ex:
#123456
The fax machine(s) that will be polling
your FAX must have this password
registered to be able to retrieve the
document.
If you do not want to register a password,
ignore this step.
Special Features
Chapter 9
11 Press OK twice.
ERASE AFTER TX
Ex:
ON
12 Use
or
to select if the document
remains in the FAX’s memory after it is
polled.
You can select from the following:
– ON
The document in the polling box is
deleted after it is retrieved by one fax
machine.
– OFF
The document in the polling box
remains in the polling box so that it
can be retrieved by an unlimited
number of fax machines.
13 Press OK.
14 Press Stop to return to standby mode.
CHANGE DATA
Ex:
15:00
FaxOnly
Once you have set up the polling box, you are ready to scan into it the document you
want other fax machines to retrieve.
Chapter 9
Special Features
913
Special Features
•
Scanning a Document into the Polling Box
Follow this procedure to store a document in the polling box so that other fax
machines can retrieve it:
You need to set up the polling box before you can scan a document into the polling box
( p. 911).
1
Load the document, face down in the ADF
( p. 43).
•
•
To adjust the resolution and contrast, see
pp. 72, 73.
You may be unable to scan if the memory
used (shown in the LCD) is close to
100%. To free up space in the FAX’s
memory: print, send, or delete any
documents you no longer need to be
stored in memory ( p. 94).
2
Press Function.
3
Press Polling.
4
Press OK.
•
Ex:
MEMORY USED 0%
(Currently used memory)
DOCUMENT READY
(Standby to scan)
POLLING TX
The FAX scans the document into the
polling box.
When another fax machine polls your FAX, the following conditions apply:
• If you registered a password for the polling box, the other party’s fax machine
must request the document with this exact same password.
• If you have not registered a password for the polling box, but the other fax
machine requests the document from your FAX with a password, the document
cannot be retrieved.
Changing or Deleting the Polling Box Settings
Follow this procedure to change or delete the polling box settings:
You will be unable to delete the polling box settings if you have scanned a document into
the polling box (see above). Delete the document from memory first before following the
procedure below ( p. 98).
1
914
Press Function.
Special Features
Chapter 9
2
Press Data Registration.
3
Press OK.
4
Use
5
Press OK.
6
Use
to select POLLING BOX.
POLLING BOX
SETUP FILE
to select the setting you want.
You can select from the following:
– CHANGE DATA
Select this setting if you want to
change the polling box settings.
– DELETE FILE
Select this setting if you want to
delete the polling box settings.
■
If you selected CHANGE DATA in step 6:
7
Press OK.
•
FILE NAME
If you registered a password to prevent
unauthorised access to the polling box
settings, use the numeric buttons to enter
it, then press OK.
8
Press OK.
9
To change the polling box settings, follow the
procedure from step 6 on p. 912.
■
If you selected DELETE FILE in step 6:
7
Press OK.
•
•
8
Chapter 9
or
USER SETTINGS
Special Features
•
or
DATA REGSTRATION
Ex:
:A
FILE DELETED
If you registered a password to prevent
unauthorised access to the polling box
settings, use the numeric buttons to enter
it, then press OK.
The polling box settings are deleted.
Press Stop to return to standby mode.
C
_anon Dpt. 1
SYSTEM SETTINGS
Ex:
15:00
FaxOnly
Special Features
915
Restricting Use of Your FAX
By enabling this feature, you can prevent unauthorised use of your FAX to make calls
and send faxes.
Enabling Restriction of Your FAX
Follow this procedure to enable restriction of your FAX:
1
Press Function.
2
Press Data Registration.
3
Press OK.
4
Use
5
Press OK three times.
or
DATA REGSTRATION
USER SETTINGS
to select SYSTEM SETTINGS.
SYSTEM SETTINGS
UN/LOCK PHONE
LOCK PHONE
Ex:
6
Use
7
Press OK twice.
or
to select ON.
ON
PASSWORD
Ex:
8
Use the numeric buttons to enter a fourdigit
password.
•
9
916
OFF
Ex:
PASSWORD
PASSWORD
_
1
_234
This password prevents unauthorised
access to the LOCK PHONE setting that
enables or disables restriction of your
FAX. If you do not want to enter a
password, ignore this step.
Press OK.
Special Features
RX RESTRICTION
Chapter 9
10 Press Stop to return to standby mode.
Ex:
15:00
FaxOnly
Restriction of your FAX is now enabled. No one can make calls or send faxes. (This
setting does not restrict incoming calls or faxes.)
Cancelling Restriction of Your FAX
Follow this procedure to cancel restriction of your FAX:
1
Press Function.
2
Press Data Registration.
3
Press OK.
4
Use
5
Press OK twice.
USER SETTINGS
to select SYSTEM SETTINGS.
SYSTEM SETTINGS
UN/LOCK PHONE
PASSWORD
6
Use the numeric buttons to enter the fourdigit
password you registered when you enabled
restriction.
•
7
_
PASSWORD
If you did not register a password, ignore
this step.
Press OK twice.
LOCK PHONE
Ex:
8
Chapter 9
Use
or
ON
to select OFF.
OFF
Special Features
917
Special Features
or
DATA REGSTRATION
9
Press OK.
10 Press Stop to return to standby mode.
PASSWORD
Ex:
15:00
FaxOnly
Restriction of your FAX is now disabled. Anyone can make calls or send faxes.
918
Special Features
Chapter 9
Restricting Reception
By enabling this feature, you can restrict reception of faxes to only the numbers
registered for speed dialling on your FAX. This feature is useful to prevent reception
of unsolicited faxes (e.g. junk mail).
Follow this procedure to enable or disable receiving restriction:
1
2
Press Function.
3
Press OK.
4
Use
5
Press OK.
6
Use
7
Press OK.
8
Use
Press Data Registration.
•
or
or
USER SETTINGS
to select SYSTEM SETTINGS.
SYSTEM SETTINGS
UN/LOCK PHONE
to select RX RESTRICTION.
RX RESTRICTION
Ex:
OFF
to select the setting you want.
You can select from the following:
– ON (Enable restriction)
– OFF (Disable restriction)
■
If you selected ON in step 8:
9
Press OK twice.
RX CONDITION
Ex:
REGSTERED SENDER
10 Use
or
to select the restriction type
setting you want.
•
Chapter 9
You can select from the following:
– REGSTERED SENDER
To allow reception from the
numbers registered for speed
dialling.
– WITH SENDER INFO
To allow reception only when the
caller gives its telephone number.
Special Features
919
Special Features
or
DATA REGSTRATION
11 Press OK.
12 Press Stop to return to standby mode.
■
If you selected OFF in step 8:
9
Press OK.
10 Press Stop to return to standby mode.
920
Special Features
DATE SETUP
Ex:
15:00
FaxOnly
DATE SETUP
Ex:
15:00
FaxOnly
Chapter 9
Chapter 10
Copying
Documents You Can Copy ........................................................................
102
❏
Making Copies ...........................................................................................
102
❏
Making a Quick Single Copy.....................................................................
103
Copying
❏
Chapter 10
Copying
101
Documents You Can Copy
For information on the types of documents you can copy, their requirements, and
details on loading documents, see Chapter 4.
Making Copies
Follow this procedure to make copies:
1
Adjust the paper delivery selector if necessary
p. 54).
(
2
Load the document, face down in the ADF
( p. 43).
•
Ex:
MEMORY USED 0%
(Currently used memory)
To adjust the contrast, see p. 73.
DOCUMENT READY
(Standby to scan)
3
Press Start/Copy.
4
Press Resolution to select the resolution
setting you want.
•
5
102
Copying
Ex:
100% 01
PHOTO
You can select from the following:
– TEXT
Suitable for most text documents.
– PHOTO
Suitable for documents that contain
photographs.
To make a reduced copy of your document,
use
or
to select the reduction
percentage you want.
•
COPY
Ex:
COPY
80% 01
You can select from the following:
– 70%
– 80%
– 90%
– 100%
Chapter 10
6
If you want to make multiple copies, use the
numeric buttons to enter the number of
copies.
•
Ex:
COPY
80% 05
You can make up to 99 copies.
The FAX copies at 400 × 300 dpi for single copies, and at 200 × 300 dpi for multiple
copies. For best quality output, make one copy at a time.
7
Press Start/Copy to begin copying.
•
COPYING
To cancel copying, press Stop. You may
then need to open the operation panel to
remove the document from the ADF
( p. 132).
You will be unable to make multiple copies if MEMORY FULL appears in the LCD. Print,
send, or delete any documents stored in memory to free up space in the FAX’s memory
( p. 94), then start again. Also, if you are copying multiple pages with many graphics,
separate the pages into smaller stacks or make the desired number of copies one at a time
as needed.
Making a Quick Single Copy
1
Load the document, face down in the ADF
( p. 43).
Ex:
MEMORY USED 0%
(Currently used memory)
DOCUMENT READY
(Standby to scan)
2
Press Start/Copy twice to begin copying.
•
Chapter 10
To cancel copying, press Stop. You may
then need to open the operation panel to
remove the document from the ADF
( p. 132).
COPY
100% 01
COPYING
Copying
103
Copying
Follow this procedure if you want to make a quick single copy of a document without
adjusting the resolution, contrast, or size:
104
Copying
Chapter 10
Chapter 11
Reports and Lists
❏
Summary of Reports and Lists...................................................................
❏
ACTIVITY REPORT ................................................................................
113
❏
TX (Transmission) REPORT.....................................................................
• MULTI TX/RX (Transaction) REPORT...............................................
114
115
❏
RX (Reception) REPORT..........................................................................
115
Reports and Lists
112
Chapter 11
Reports and Lists
111
Summary of Reports and Lists
The table below shows the lists and reports that can be printed from your FAX. Refer
to the pages indicated for more details.
Report or List
Description
Details
USER’S DATA LIST
Lists the current settings of your FAX and the registered
p. 142
sender information.
ACTIVITY REPORT
Shows recent facsimile transactions performed by your
p. 113
FAX.
p. 145
You can enable or disable automatic printing of this
report after every 20 transactions. You can also manually
set the FAX to print it.
TX (Transmission) REPORT
Prints after transmission of a document.
p. 114
You can enable or disable this feature, or set the FAX to
p. 145
print a report only when an error occurs.
You can also set the FAX to print the first page of the
document under the report to remind you of the contents
of the document.
RX (Reception) REPORT
Prints after reception of a document. You can enable or
p. 115
disable this feature, or set the FAX to print a report only
p. 145
when an error occurs.
MULTI TX/RX (Transaction) REPORT Prints after sending the same document to several fax
p. 115
numbers, or after polling multiple fax numbers in one
operation.
DOC. MEMORY LIST
Lists the documents currently stored in the FAX’s
p. 94
memory.
MEMORY CLEAR REPORT
Prints automatically when power is restored to the FAX
p. 1322
after a power cut. Lists the documents deleted from
memory.
1TOUCH SPD DIAL LIST 1
Lists the numbers and names registered under onetouch
1TOUCH SPD DIAL LIST 2
speed dialling buttons.
CODED SPEED DIAL LIST 1
Lists the numbers and names registered under coded
CODED SPEED DIAL LIST 2
speed dialling codes.
GROUP DIAL LIST
Lists groups registered under onetouch speed dialling
p. 618
p. 619
p. 620
buttons and coded speed dialling codes.
112
Reports and Lists
Chapter 11
ACTIVITY REPORT
The FAX is factoryset to automatically print an ACTIVITY REPORT after every 20
transactions. If you want to print an ACTIVITY REPORT before it is automatically
printed, follow this procedure:
1
Press Function.
2
Press Report.
3
Press OK.
•
ACTIVITY REPORT
PRINTING REPORT
The FAX prints an ACTIVITY
REPORT.
Transactions in an ACTIVITY REPORT are listed chronologically.
27/12 2002 15:00 FAX 123 4567
CANON
001
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
ACTIVITY REPORT
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
ST. TIME
CONNECTION TEL
NO.
CONNECTION ID
PGS. RESULT
MODE
* 27/12 13:43
* 27/12 13:45
905 795 1111 Canon CANADA
905 795 1111 Canon CANADA
5001 AUTO RX
0001 POLLING RX
ECM
ECM
* 27/12
* 27/12
* 27/12
* 27/12
* 27/12
27/12
27/12
27/12
03 3758 2111
2 887 0166
905 795 1111
2 887 0166
20 545 8545
20 545 8545
03 3758 2111
2 887 0166
0002
0002
5002
5003
0003
0004
0004
0005
ECM
ECM
ECM
ECM
ECM
ECM
ECM
ECM
13:51
13:53
14:10
14:16
14:27
14:30
14:31
14:57
27/12 14:59
Canon TOKYO
Canon AUSTRALIA
Canon CANADA
Canon AUSTRALIA
Canon EUROPA
Canon EUROPA
Canon TOKYO
Canon AUSTRALIA
1 432 2060 CANON OPTICS
B'CAST
B'CAST
AUTO RX
AUTO RX
DELAYED TX
DEL SQ BDCST
DEL SQ BDCST
TRANSMIT
0006 TRANSMIT
1 OK 00'33
0 OK 00'00
0 STOP
3 OK 01'18
3 OK 01'18
1 OK 00'18
4 OK 03'59
1 OK 01'20
1 OK 00'36
1 OK 00'36
3 OK 01'25
0 STOP
0 OK 00'01
0 #018
TRANSACTION (TX/RX) NUMBER
TRANSACTION MODE
Reports and Lists
INDICATES AN
ENTRY THAT HAS
APPEARED ON A
PREVIOUS REPORT.
ERROR CORRECTION MODE TRANSACTION
ERROR PAGE
ERROR CODE (
p. 13-8)
Stop PRESSED DURING TRANSACTION
TRANSACTION DURATION
•
•
Chapter 11
If you prefer the FAX not to print an ACTIVITY REPORT after every 20 transactions,
disable the ACTIVITY REPORT setting ( p. 145).
Please note that only one transaction number (TX/RX NO.) is assigned when you send
a document to several fax numbers in one operation.
Reports and Lists
113
TX (Transmission) REPORT
The FAX is factoryset to print a TX (transmission) REPORT only when an error
occurs during sending. To change this setting, see TX REPORT, p. 145.
If you set the FAX to print a report, a TX REPORT or an ERROR TX REPORT
similar to the ones below, will be printed depending on the setting you select.
27/12 2002 14:52 FAX 123 4567
CANON
001
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
TX REPORT
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
TRANSMISSION OK
TX/RX NO
CONNECTION TEL
SUBADDRESS
0003
1 432 2060
27/12 2002 14:59 FAX 123 4567
CANON
001
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
ERROR TX REPORT
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
TX FUNCTION WAS NOT COMPLETED
TX/RX NO
CONNECTION TEL
SUBADDRESS
CONNECTION ID
ST.TIME
USAGE T
PGS. SENT
RESULT
0004
20 545 8545
Canon EUROPA
27/12 14:59
00’18
1
NG
THE SLEREXE COMPANY LIMITED
SAPORS LANE·BOOLE·DORSET·BH25 8ER
TELEPHONE BOOLE (945 13) 51617 – FAX 123456
Our Ref. 350/PJC/EAC
27 December, 2002
Dr. P. N. Cundall,
Mining Surveys Ltd.,
Holroyd Road,
Reading
Berks.
OK: TRANSMISSION SUCCESSFUL
NG: SOME OR NO PAGES SENT
NUMBER OF PAGES SENT
TRANSMISSION DURATION
TRANSMISSION TIME
114
Reports and Lists
IF YOU ENABLE THE PRINT WITH IMAGE
SETTING (
p. 14-5), THE FIRST PAGE OF
THE FAX WILL PRINT ON THE REPORT TO
REMIND YOU OF THE CONTENTS OF THE FAX.
Chapter 11
MULTI TX/RX (Transaction) REPORT
A MULTI TX/RX (transaction) REPORT similar to the one below, is printed when
you send the same document to several fax numbers, or when you poll multiple fax
numbers in one operation.
27/12 2002 17:23 FAX 123 4567
CANON
001
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
MULTI TX/RX REPORT
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
TX/RX NO
PGS.
TX/RX INCOMPLETE
TRANSACTION OK
0054
1
______
[
01] 905 795 1111
[
01] 03 3758 2111
[
02] 1 49 39 25 25
______
ERROR INFORMATION
Canon CANADA
Canon TOKYO
Canon FRANCE
RX (Reception) REPORT
The FAX is factoryset not to print an RX (reception) REPORT even if an error
occurs during reception. To change this setting, see RX REPORT, p. 145.
If you set the FAX to print a report, an RX REPORT similar to the one below, will
be printed.
27/12 2002 15:02 FAX 123 4567
CANON
001
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
RX REPORT
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
RECEPTION OK
5004
905 795 1111
Canon CANADA
27/12 14:59
01’59
4
OK
Reports and Lists
TX/RX NO
CONNECTION TEL
SUBADDRESS
CONNECTION ID
ST.TIME
USAGE T
PGS.
RESULT
OK: TRANSMISSION SUCCESFUL
NG: SOME OR NO PAGES RECEIVED
NUMBER OF PAGES RECEIVED
RECEPTION DURATION
RECEPTION TIME
Chapter 11
Reports and Lists
115
116
Reports and Lists
Chapter 11
Chapter 12
Maintenance
Periodic Cleaning.......................................................................................
• Cleaning the FAX’s Exterior .................................................................
• Cleaning the FAX’s Interior ..................................................................
• Cleaning the Scanner Components ........................................................
122
122
123
124
❏
Replacing the Toner Cartridge...................................................................
126
Maintenance
❏
Chapter 12
Maintenance
121
Periodic Cleaning
This section describes the necessary cleaning procedures for your FAX. Please note
the following before cleaning your unit:
• Be sure to disconnect the power cord before cleaning the FAX. Since documents
in memory are erased when the power is disconnected, print or send any
documents stored in memory before disconnecting the power cord ( p. 94).
• Do not use tissue paper, paper towels, or similar materials for cleaning; they can
stick to the components or generate static charges.
Never use volatile liquids such as thinners, benzene, acetone, or any other chemical
cleaner to clean the interior of the FAX; these can damage the unit’s components.
Cleaning the FAX’s Exterior
Follow this procedure to clean the FAX’s outer casing:
122
1
Disconnect the power cord from the FAX.
2
Wipe the FAX’s exterior with a clean, soft,
lintfree cloth moistened with water or diluted
dishwashing detergent solution.
3
When you finished, reconnect the power cord.
Maintenance
Chapter 12
Cleaning the FAX’s Interior
To prevent toner powder and paper dust from accumulating inside the FAX and
affecting print quality, clean the unit’s print area periodically.
Follow this procedure to clean inside the FAX:
1
2
Disconnect the power cord from the
FAX.
Lift the latch and open the front cover.
Do not open the front cover without
lifting the latch since this may
damage your unit.
3
Hold the toner cartridge by its handle
and remove it from the FAX.
• To avoid exposing the toner
cartridge to light, place it in its
protective bag or wrap it in a thick
cloth.
HANDLE
4
Use a clean, soft, dry, lintfree cloth to
remove any toner or paper debris from
the unit’s interior (shaded area in the
illustration).
• The fixing assembly becomes
extremely hot when the unit is in
use. Be very careful not to touch it
so as to avoid injury.
• Be careful not to touch the black
transfer charging roller since this
adversely affects print quality.
DO NOT TOUCH THE
FIXING ASSEMBLY
Maintenance
DO NOT TOUCH THE BLACK
TRANSFER CHARGING ROLLER
Chapter 12
Maintenance
123
5
When you are finished, reinsert the
toner cartridge. Hold the toner cartridge
by its handle and insert it into the FAX
as far as it will go, making sure that its
tabs are aligned with the rails inside the
unit.
• Always hold the toner cartridge by
its handle.
6
Use both hands to close the front cover.
7
Reconnect the power cord.
Cleaning the Scanner Components
Follow this procedure to periodically check and clean the scanner components:
1
Disconnect the power cord from the
FAX.
2
Use both hands to gently open the
operation panel.
•
3
It only opens partially.
While holding the operation panel
open, clean these components:
❏
❏
Separation guide and separation
roller:
Wipe with a clean, soft, dry, lint
free cloth.
White sheet and scanning glass:
Wipe with a clean, soft, lintfree
cloth moistened with water, then
wipe with a clean, soft, dry, lint
free cloth.
SEPARATION
ROLLER
SCANNING GLASS
WHITE SHEET
SEPARATION GUIDE
124
Maintenance
Chapter 12
•
•
•
4
Clean the underside of the operation
panel (shaded area in the illustration).
•
5
If the scanner components are dirty, the documents you send or copy
will also be dirty.
Be sure to use a soft cloth to avoid scratching the components.
Do not use tissue paper, paper towels, or similar materials for
cleaning; they can stick to the components or generate static charges.
Dirt and dust particles that collect
on the underside of the operation
panel affect the quality of the
documents you copy or send.
Use a clean, soft, dry, lintfree cloth to
wipe any paper dust from the areas
surrounding the separation roller
(shaded area in the the illustration).
SEPARATION
ROLLER
6
When you are finished, close the
operation panel by pressing it down
from the centre.
•
Reconnect the power cord.
Maintenance
7
Be sure to close the operation
panel until it locks into place, or
the unit will not function properly.
Chapter 12
Maintenance
125
Replacing the Toner Cartridge
The only component of your FAX you will need to replace is the FX3 toner
cartridge. Although Canon manufactures many different toner cartridges, the FX3
toner cartridge is the only one designed for use with your FAX. To purchase this toner
cartridge, contact your local authorised Canon dealer or the Canon help line.
When CHANGE CARTRIDGE appears in the LCD, you may need to replace the toner
cartridge. However, it may also indicate that the toner inside the toner cartridge is
simply unevenly distributed. Before replacing the toner cartridge, follow this
procedure to distribute the toner evenly:
1
Remove the toner cartridge from the
FAX ( steps 1 to 4, below).
2
Gently rock the toner cartridge from
side to side a few times to distribute the
toner evenly inside it.
•
3
Poor print quality may result if the
toner is unequally distributed.
Reinsert the toner cartridge into the
FAX ( steps 8 and 9, p. 128).
If after following the procedure above, CHANGE CARTRIDGE remains in the LCD or
print quality does not improve, follow this procedure to replace the toner cartridge:
1
Remove any documents and printouts
from the FAX.
2
3
Make sure the FAX is plugged in.
Lift the latch and open the front cover.
Do not open the front cover without
lifting the latch since this may
damage your unit.
126
Maintenance
Chapter 12
4
Hold the toner cartridge by its handle
and remove it from the FAX.
•
Discard the old toner cartridge
immediately according to the local
laws and regulations for disposal
of consumables. To recycle your
used toner cartridge, simply follow
the instructions included with your
new FX3 toner cartridge.
HANDLE
5
Remove the new FX3 toner cartridge
from its protective bag.
•
6
Gently rock the toner cartridge from
side to side a few times to distribute the
toner evenly inside it.
•
7
Save the protective bag in case you
need to repack the toner cartridge
at a later date.
Poor print quality may result if the
toner is unequally distributed.
Place and support the toner cartridge on
a flat, clean surface, then gently pull on
the plastic tab to remove the plastic
seal.
•
Use a firm, even pull to avoid
breaking the seal.
SIDE VIEW
PULL WITHIN
THIS RANGE
TOP VIEW
Maintenance
PULL WITHIN
THIS RANGE
Chapter 12
Maintenance
127
8
Hold the toner cartridge by its handle
and insert it into the FAX as far as it
will go, making sure that its tabs are
aligned with the rails inside the unit.
•
9
128
Always hold the toner cartridge by
its handle.
Use both hands to close the front cover.
Maintenance
Chapter 12
Chapter 13
❏
Clearing Jams.............................................................................................
• Jams in the ADF ....................................................................................
• Paper Jams .............................................................................................
Jams in the Paper Delivery Slots ........................................................
Jams Inside the Unit............................................................................
132
132
133
133
133
❏
LCD Messages ...........................................................................................
138
❏
Paper Feeding Problems............................................................................. 1313
❏
Faxing Problems ........................................................................................ 1313
• Sending Problems .................................................................................. 1313
• Receiving Problems ............................................................................... 1315
❏
Copying Problems...................................................................................... 1317
❏
Telephone Problems................................................................................... 1318
❏
Printing Problems....................................................................................... 1318
❏
General Problems....................................................................................... 1320
❏
If You Cannot Solve a Problem ................................................................. 1321
❏
If a Power Cut Occurs................................................................................ 1322
Troubleshooting
131
Troubleshooting
Chapter 13
Troubleshooting
Clearing Jams
Jams in the ADF
When a document jams or misfeeds in the ADF, the LCD displays CHECK DOCUMENT.
Follow this procedure to clear the document jam:
You do not need to unplug the FAX when clearing document jams.
1
Press Stop.
2
Use both hands to gently open the
operation panel.
•
•
3
It only opens partially.
Do not try to pull the document out
without opening the operation
panel since you may tear or
smudge the document.
While holding the operation panel
open, remove the document.
•
•
Pull it gently in either direction.
If a multipage document is loaded,
remove the entire document from
the ADF.
If the paper does not pull out easily,
do not force it. Contact your local
authorised Canon dealer or the
Canon help line.
4
When you are finished, close the
operation panel by pressing it down
from the centre.
•
132
Be sure to close the operation
panel until it locks into place, or
the unit will not function properly.
Troubleshooting
Chapter 13
When paper jams in the FAX, the LCD displays CLEAR PAPER JAM. Try clearing the
jam by following the procedure in Jams in the Paper Delivery Slots below. If this
does not clear the jam, follow the procedure in Jams Inside the Unit.
Jams in the Paper Delivery Slots
Follow this procedure to clear a paper jam in the paper delivery slots:
You do not need to unplug the FAX when clearing paper jams.
1
Gently pull any jammed paper out of
the unit as shown.
2
Remove the paper stack from the multi
purpose tray and reload it ( p. 215).
If the paper jam occurred while a fax was being received into the FAX’s memory, that fax
will print automatically when the jam is cleared.
Jams Inside the Unit
Follow this procedure to clear a paper jam inside the unit:
You do not need to unplug the FAX when clearing paper jams.
1
Lift the latch and open the front cover.
Do not open the front cover without
lifting the latch since this may
damage your unit.
Chapter 13
Troubleshooting
133
Troubleshooting
Paper Jams
2
Hold the toner cartridge by its handle
and remove it from the FAX.
•
To avoid exposing the toner
cartridge to light, place it in its
protective bag or wrap it in a thick
cloth.
HANDLE
3
Move the paper release lever back.
• The fixing assembly becomes
extremely hot when the unit is in
use. Be very careful not to touch it
so as to avoid injury.
• Be careful not to touch the
transfer charging roller since this
adversely affects print quality.
DO NOT TOUCH THE
FIXING ASSEMBLY
DO NOT TOUCH THE BLACK
TRANSFER CHARGING ROLLER
134
Troubleshooting
Chapter 13
Locate the paper jam and clear it as
explained on the following pages.
Troubleshooting
4
1 MULTI-PURPOSE
TRAY AREA
2 FIXING ASSEMBLY AREA
1 Multipurpose tray area:
Hold the unit steady and carefully pull
the jammed paper straight out from the
unit.
•
•
•
Chapter 13
Do this carefully to prevent tearing
the jammed paper. If you do tear it,
be sure to remove any torn pieces
from the unit since these will cause
paper to jam again.
The toner on the paper will not have
been fixed to the paper yet, so remove
the jammed paper carefully to avoid
soiling the inside of the unit. Loose
toner powder inside the unit may
adversely affect print quality.
Loose toner powder can soil any
surface; protect yourself and your
work area. Remove immediately any
toner powder from yourself or your
clothing with cold water.
Troubleshooting
135
2 Fixing assembly area:
Top edge of the jammed paper in the
fixing assembly:
Push the jammed paper back ~, then pull
it carefully towards you to remove it Ä.
The fixing assembly becomes
extremely hot when the unit is in
use. Be very careful not to touch it
so as to avoid injury.
2
1
DO NOT TOUCH THE
FIXING ASSEMBLY
Top edge of the jammed paper has
passed through the fixing assembly:
Pass the jammed paper under the roller.
Use both hands to carefully pull out the
jammed paper.
•
136
Do this carefully to prevent tearing
the jammed paper. If you do tear it,
be sure to remove any torn pieces
from the unit since these will cause
paper to jam again.
Troubleshooting
Chapter 13
When you finished, reinsert the toner
cartridge. Hold the toner cartridge by
its handle and insert it into the FAX as
far as it will go, making sure that its
tabs are aligned with the rails inside the
unit.
•
Troubleshooting
5
Always hold the toner cartridge by
its handle.
6
7
Move the paper release lever forward.
8
Reload paper in the multipurpose tray
( p. 215).
Use both hands to close the front cover.
If you are experiencing repeated paper jams, it may be due to the paper you are using:
– Tap the paper on a flat surface before stacking it in the multipurpose tray.
– Check that the paper you are using meets the requirements for your unit ( p. 52).
– Make sure you have completely removed any scraps of paper from inside the FAX.
Not doing so will cause paper to jam again.
Chapter 13
Troubleshooting
137
LCD Messages
The following messages are displayed in the LCD when the FAX is performing a
task, or when it encounters an error. The error code appears in the ACTIVITY
REPORT ( p. 113).
Messsage
Error Code
Cause
AUTO REDIAL
—
The unit is waiting to redial Wait for the unit to automatically
the other party’s fax
redial the fax number (
p. 79).
number because the line
was busy or the other party
did not answer when you
tried to send the document.
BUSY/NO SIGNAL
#018
The fax/telephone number
you dialled is busy.
Try sending the document at a later
time.
The fax number dialled
was incorrect.
Check the fax number and dial again.
The other party’s fax
machine is not working.
Contact the other party and have them
check their fax machine.
The other party is not using
a G3 fax machine.
Contact the other party to check that
they are using a G3 fax machine.
The telephone line type
setting on your unit is
incorrect.
Set your unit for your telephone line
type (
p. 38).
The receiving fax machine
did not answer within
55 seconds (after all
automatic redialling
attempts).
Contact the other party and have them
check their fax machine. You can try
to send the document using manual
sending via the handset (
p. 76).
For an overseas call, add pauses to the
registered number (
p. 92).
The toner inside the toner
cartridge may be unevenly
distributed.
Redistribute the toner inside the toner
cartridge (
p. 126). If the message
remains, replace the toner cartridge
(
p. 126).
The toner cartridge is
empty.
Replace the toner cartridge
(
p. 126).
CHANGE CARTRIDGE
138
Troubleshooting
—
Action
Chapter 13
Error Code
Cause
Action
CHECK COVER
—
The front cover is open.
Close the front cover.
CHECK DOCUMENT
#001
A document is jammed in
the ADF.
Clear the document jam (
Then start again.
CHECK PAPER SIZE
—
The size of the paper in the
multipurpose tray and that
specified in the PAPER
SIZE setting are different.
Load the correct paper size
(
p. 215) or change the PAPER
SIZE setting (
p. 56) to match the
size of the paper loaded in the multi
purpose tray.
CHECK POLLING ID
#021
No subaddress and/or
password has been entered
on your unit, or the
subaddress and/or
password do not match the
settings on the other party’s
fax machine.
Make sure the subaddress and/or
password match the settings on the
other party’s fax machine
(
p. 99).
#008
No subaddress and/or
password has been entered
on the other party’s
machine, or the subaddress
and/or password do not
match the settings on your
unit.
Contact the other party to enter the
correct subaddress and/or password.
—
The toner cartridge may be
defective.
Reinstall the toner cartridge
(
p. 212). If the message remains
in the LCD, replace the toner
cartridge (
p. 126).
The unit is connected to an
uninterruptible power
supply (UPS).
Make sure the unit is plugged into an
AC outlet.
CHECK PRINTER
p. 132).
In either case, if the error does not
clear, try unplugging the unit. Wait
five seconds, then plug it back in. If
the message remains in the LCD,
contact your local authorised Canon
dealer or the Canon help line.
Chapter 13
Troubleshooting
139
Troubleshooting
Messsage
Messsage
Error Code
Cause
CHK SUBADDR/PSWD
#083/12
You attempted to send a
Contact the other party to check their
document or poll another
settings. Change your settings if
fax machine with the
necessary (
pp. 63, 67, 99).
incorrect subaddress and/or
password.
CLEAR PAPER JAM
—
There is a paper jam.
Clear the paper jam (
p. 133),
then reload paper in the multi
purpose tray (
p. 215).
DOC. TOO LONG
#003
The document is longer
than 1 metre.
Use a copier to make a reduced copy
of the document and then send the
copy.
ECM RX
—
The unit is receiving a fax
using Error Correction
Mode (ECM).
Receiving with ECM may take longer
than normal receptions. Turn off
ECM if you need to receive quickly,
or if you know your local lines are in
ECM RX,
good condition (
p. 147).
ECM TX
—
The unit is sending a fax
using Error Correction
Mode (ECM).
Sending with ECM may take longer
than normal transmissions. Turn off
ECM if you need to transmit quickly,
or if you know your local lines are in
ECM TX,
good condition (
p. 146).
LOAD PAPER
—
The multipurpose tray is
empty.
Load paper in the multipurpose tray
(
p. 215), then press Stop.
MEMORY FULL
#037
The unit’s memory is full
because it has received too
many documents, or a very
long or detailed document.
Print any documents stored in
memory (
p. 95). Then start
again.
The unit’s memory is full
because you tried to send or
copy too many pages at
once, or a very long or
detailed document.
Divide the document and send or
copy each part separately. To free up
space in the unit’s memory, print,
send, or delete any documents in
memory you no longer need
(
p. 94).
1310
Troubleshooting
Action
Chapter 13
Error Code
Cause
Action
MEMORY USED nn %
—
Shows the percentage of
memory currently in use.
If you need more space, wait for the
unit to send any faxes. Also, print,
send, or delete any documents in
memory you no longer need
(
p. 94).
NO RX PAPER
#012
The other party’s fax
machine is out of paper or
its memory is full.
Contact the other party and have them
load paper in their fax machine or free
up space in their fax machine’s
memory.
NO TEL #
#022
The onetouch speed
dialling button or coded
speed dialling code you
entered has not been
registered.
Register the onetouch speed dialling
button or coded speed dialling code
(
Chapter 6).
NOT AVAILABLE
—
You entered an invalid
number.
Enter a valid number.
PSWD POLL REJECT
#084
You attempted to poll a fax
machine with a password,
but the other party has not
set a password or their fax
machine does not support
polling with a password.
Contact the other party to check their
settings. If their fax machine does not
support polling with a password,
delete the password you have
registered (
pp. 63, 67, 69).
PSWD TX REJECTED
#081
You attempted to send a
document with a password,
but the other party’s fax
machine does not support
reception with a password.
Contact the other party to check their
settings. If their fax machine does not
support reception with a password,
delete the password you have
registered (
pp. 63, 67).
Chapter 13
Troubleshooting
1311
Troubleshooting
Messsage
Messsage
Error Code
Cause
Action
REC’D IN MEMORY
—
The unit received the fax in
memory because paper or
toner ran out, or a paper
jam occurred during
reception.
Load paper in the multipurpose tray
(
p. 215), replace the toner
cartridge (
p. 126), or clear the
paper jam (
p. 133).
SELECT POL REJCT
#082
You attempted to poll a fax
machine with a subaddress,
but the other party has not
set a subaddress or their fax
machine does not support
polling with a subaddress.
Contact the other party to check their
settings. If their fax machine does not
support polling with a subaddress,
delete the subaddress you have
registered (
pp. 63, 67, 99).
SUBADD TX REJECT
#080
You attempted to send a
document with a
subaddress, but the other
party’s fax machine does
not support reception with
a subaddress.
Contact the other party to check their
settings. If their fax machine does not
support reception with a subaddress,
delete the subaddress you have
registered (
pp. 63, 67).
TX/RX CANCELLED
—
You pressed Stop to cancel
a transaction.
—
TX/RX NO. nnnn
—
The number shown (nnnn)
is a unique identification
number assigned to the
document you are sending
or receiving.
This number appears in reports so you
can identify transactions. Write the
number down if you will need it later.
TX/RX NO. nnnn
SCANNING P.nnn
MEMORY FULL
(Three messages
toggle.)
—
The unit is sending a
document and its memory
is full.
The unit continues to send the
document as memory becomes
available.
1312
Troubleshooting
Chapter 13
■ Paper does not feed properly.
The multipurpose tray may contain too many sheets.
• Make sure you load the correct quantity ( p. 52).
The paper may not be loaded correctly.
• Make sure the paper stack is loaded correctly in the multipurpose tray
( p. 215).
■ Multiple sheets feed together into the FAX.
The paper may not be loaded correctly.
• Make sure the paper stack is loaded correctly in the multipurpose tray
( p. 215).
The multipurpose tray may contain too many sheets.
• Make sure you load the correct quantity ( p. 52).
Different types of paper may be loaded in the multipurpose tray.
• Load only one type of paper.
• Make sure you load paper that meets the requirements for the FAX
( p. 52).
• Let the paper run out before refilling the multipurpose tray. Avoid mixing
new stock with paper already loaded.
■ Repeated paper jams occur.
The paper you are using may be causing the jams.
• Make sure you load paper that meets the requirements for the FAX
( p. 52).
Faxing Problems
Sending Problems
■ Cannot send a fax.
The FAX may not be set for the correct telephone line type.
• Make sure the FAX is set for the correct telephone line type (
The document may not be loaded correctly.
• Make sure the document is loaded correctly in the ADF (
• Make sure the operation panel is closed.
p. 38).
p. 43).
The onetouch speed dialling button or coded speed dialling code you
entered may not be registered correctly.
• Check that the speed dialling settings are registered correctly
( Chapter 6).
Chapter 13
Troubleshooting
1313
Troubleshooting
Paper Feeding Problems
You dialled or have been provided with an incorrect number.
• Dial the number again, or check that you have the correct number.
The other party’s fax machine may be out of paper.
• Contact the other party and ask them to make sure paper is loaded in their
fax machine.
There may be other documents being sent from memory.
• Allow time for those documents to finish sending.
An error may have occurred during sending.
• Print an ACTIVITY REPORT and check for an error code (
p. 113).
The telephone line may not be working properly.
• Make sure there is a dial tone when you press Hook or when you lift the
handset of any external device connected to the FAX. If there is no dial tone,
contact your local telephone company.
The receiving fax machine may not be a G3 fax machine.
• Make sure the receiving fax machine is compatible with your FAX (which
is a G3 fax machine).
The subaddress and/or password are incorrect.
• If you registered a subaddress/password under a speed dialling button or
code, make sure they match the other party’s settings.
■ Faxes sent from the FAX are spotted or dirty.
The receiving fax machine may not be working properly.
• Check the FAX by making a copy ( p. 102). If the copy is clear, the
problem may be in the receiving fax machine. If the copy is spotted or dirty,
clean the scanner components ( p. 124).
The document may not be loaded correctly.
• Make sure the document is loaded correctly in the ADF (
p. 43).
■ Cannot send using Error Correction Mode (ECM).
The other party’s fax machine may not support ECM.
• If this is the case, the document is sent without ECM.
ECM may be disabled.
• Make sure ECM on your FAX is enabled ( ECM TX, p. 146).
• Contact the other party to check if ECM on their fax machine is enabled.
1314
Troubleshooting
Chapter 13
The telephone lines may be in poor condition, or you may have a bad
connection.
• Lower the transmission speed ( TX START SPEED, p. 1410).
If none of these solutions solve the problem, unplug the FAX and wait for at least five
seconds. Then plug it back in and try sending again. If you still cannot send, contact your
local authorised Canon dealer or the Canon help line.
Receiving Problems
■ Cannot receive a fax automatically.
The FAX may not be set to receive automatically.
• For the FAX to receive faxes automatically, the receive mode must be set to
FAX ONLY MODE, Fax/Tel Mode, ANS.MACHINE MODE, or NET SWITCH*
( Chapter 8). If you have set ANS.MACHINE MODE, confirm that an
answering machine is connected to the FAX and that it is turned on with an
outgoing message properly recorded ( p. 89).
The FAX may have a document stored in memory, leaving little or no
memory available.
• Print, send, or delete any documents stored in memory ( p. 94).
An error may have occurred during reception.
• Check the LCD for an error message ( p. 138).
• Print an ACTIVITY REPORT and check for an error code (
The multipurpose tray may be empty.
• Make sure paper is loaded in the multipurpose tray (
p. 113).
p. 215).
The telephone line cord may not be connected properly.
• Make sure it is connected properly ( p. 25).
■ No automatic switching between telephone and fax calls.
The FAX may not be set to switch automatically between telephone and fax
calls.
• For the FAX to switch automatically, the receive mode must be set to Fax/
Tel Mode, ANS.MACHINE MODE, or NET SWITCH*. If you have set
ANS.MACHINE MODE, confirm that an answering machine is connected
to the FAX and that it is turned on with an outgoing message properly
recorded ( p. 89).
The FAX may have a document stored in memory, leaving little or no
memory available.
• Print, send, or delete any documents stored in memory ( p. 94).
*
Chapter 13
NET SWITCH is available for certain countries only.
Troubleshooting
1315
Troubleshooting
■ Errors occur frequently while sending.
An error may have occurred during reception.
• Check the LCD for an error message ( p. 138).
• Print an ACTIVITY REPORT and check for an error code (
The multipurpose tray may be empty.
• Make sure paper is loaded in the multipurpose tray (
p. 113).
p. 215).
The other party’s fax machine may not send the CNG signal that tells your
FAX that the incoming call is a fax call.
• Some fax machines cannot send this signal. In such cases, you will have to
receive the fax manually ( p. 87).
■ Cannot receive a document manually.
You may have disconnected the call by pressing Start/Copy or dialling the
remote receiving ID after hanging up.
• Always press Start/Copy or dial the remote receiving ID before hanging up.
Otherwise you will disconnect the call ( p. 87).
■ Print quality is poor.
You may not be using the correct paper type.
• Make sure you load paper that meets the requirements for the FAX
( p. 52).
The other party’s fax machine may not be functioning properly.
• The sending fax machine usually determines the fax’s quality. Contact the
other party and have them check that the scanning components of their fax
machine are clean.
Error Correction Mode (ECM) may be disabled.
• Make sure ECM is on ( ECM RX, p. 147).
■ Faxes do not print.
The toner cartridge may not be installed properly.
• Make sure the toner cartridge is installed properly (
p. 212).
The toner cartridge may need to be replaced.
• Replace the toner cartridge ( p. 126).
■ Received faxes print blotched or unevenly.
The telephone lines may be in poor condition, or you may have a bad
connection.
• Error Correction Mode (ECM) sending/receiving should eliminate such
problems. However, if the telephone lines are in poor condition, you may
have to try again.
The other party’s fax machine may not be functioning properly.
• The sending fax machine usually determines the fax’s quality. Contact the
other party and have them check that the scanning components of their fax
machine are clean.
1316
Troubleshooting
Chapter 13
p. 126). If the problem
■ Cannot receive using Error Correction Mode (ECM).
The other party’s fax machine may not support ECM.
• If this is the case, the document is received without ECM.
ECM may be disabled.
• Make sure ECM on your FAX is enabled ( ECM RX, p. 147).
• Contact the other party to check if ECM on their fax machine is enabled.
■ Errors occur frequently while receiving.
The telephone lines may be in poor condition, or you may have a bad
connection.
• Lower the reception speed ( RX START SPEED, p. 1411).
The other party’s fax machine may not be functioning properly.
• Contact the other party and have them check that their fax machine is
functioning properly.
Copying Problems
■ Cannot make copies.
The document may not be loaded correctly.
• Make sure the document is loaded correctly in the ADF (
• Make sure the operation panel is closed.
p. 43).
The document may not meet the requirements for the FAX.
• Make sure you load documents that meet the requirements for the FAX
( p. 42).
■ MEMORY FULL appears in the LCD when making
multiple copies.
The FAX’s memory is full.
• Print, send, or delete any documents stored in memory (
space in the FAX’s memory, then start again.
p. 94) to free up
The document you are copying may have too many graphics.
• If multiple pages are being copied, separate the pages into smaller stacks. If
not, make the desired number of copies one at a time as needed.
For additional troubleshooting, see Printing Problems, p. 1318.
Chapter 13
Troubleshooting
1317
Troubleshooting
Toner may be low or unevenly distributed.
• Redistribute the toner inside the toner cartridge (
persists, replace the toner cartridge ( p. 126).
Telephone Problems
■ Cannot dial.
The telephone line cord may not be connected properly.
• Make sure it is connected properly ( p. 25).
The power cord may not be plugged in securely.
• Check that the power cord is plugged securely into the FAX and into the wall
outlet ( p. 27). If the unit is plugged into a power strip, make sure the
power strip is plugged in and turned on.
The FAX may not be set for the correct telephone line type.
• Make sure the FAX is set for the correct telephone line type (
p. 38).
■ Optional handset or telephone disconnects while you are
talking.
The power cord may not be plugged in securely.
• Check that the power cord is plugged securely into the FAX and into the wall
outlet ( p. 27). If the unit is plugged into a power strip, make sure the
power strip is plugged in and turned on.
The optional handset or telephone cord may be defective.
• Check the cord by substituting with another cord.
Printing Problems
■ Alarm light is lit and the FAX beeps while printing.
The FAX may have a paper jam.
• Clear the paper jam ( p. 133).
• If the FAX has no paper jam, unplug the unit and wait 5 seconds, then plug
it back in. If the Alarm light remains lit, contact your local authorised Canon
dealer or the Canon help line.
■ Nothing prints.
The power cord may not be plugged in securely.
• Check that the power cord is plugged securely into the FAX and into the wall
outlet ( p. 27). If the unit is plugged into a power strip, make sure the
power strip is plugged in and turned on.
1318
Troubleshooting
Chapter 13
The toner cartridge may need to be replaced.
• Replace the toner cartridge ( p. 126).
■ Printout does not match paper size.
The paper may not be loaded correctly.
• Make sure the paper stack is loaded correctly in the multipurpose tray
( p. 215).
■ Printout is skewed.
The paper may not be loaded correctly.
• Make sure the paper stack is loaded correctly in the multipurpose tray
( p. 215).
• Make sure the paper delivery slots are clear.
■ Paper jams occur.
You may not be using the correct paper delivery slot.
• Select the correct paper delivery slot ( p. 54).
■ Printout is not clear.
You may not be using the correct paper type.
• Make sure you load paper that meets the requirements for the FAX
( p. 52).
You may be printing on the wrong side of the paper.
• Some papers have a “right” side for printing. If the print quality is not as
clear as you would like it to be, try turning the paper over and printing on the
other side.
■ Printout has vertical white streaks.
Toner may be low or unevenly distributed.
• Redistribute the toner inside the toner cartridge (
persists, replace the toner cartridge ( p. 126).
Chapter 13
p. 126). If the problem
Troubleshooting
1319
Troubleshooting
You may not have removed the plastic seal from the toner cartridge.
• Make sure you install the toner cartridge properly ( p. 212).
General Problems
■ FAX has no power.
The power cord may not be plugged in securely.
• Check that the power cord is plugged securely into the FAX and into the wall
outlet ( p. 27). If the unit is plugged into a power strip, make sure the
power strip is plugged in and turned on.
The power cord may not be supplying power.
• Check the power cord by substituting with another, or by using a voltmeter
to test it for continuity.
■ Nothing appears in the LCD.
The power cord may not be plugged in securely.
• Check that the power cord is plugged securely into the FAX and into the wall
outlet ( p. 27). If the unit is plugged into a power strip, make sure the
power strip is plugged in and turned on. If the LCD remains blank, unplug
the unit and wait five seconds, then plug it back in. If the LCD still remains
blank, contact your local authorised Canon dealer or the Canon help line.
1320
Troubleshooting
Chapter 13
If you cannot solve the problem after having referred to the information in this
chapter, contact your local authorised Canon dealer or the Canon help line.
Canon’s support personnel are trained in the technical support of Canon’s products
and will able to help you with your problem.
Attempting to repair the FAX yourself may void the limited warranty.
If the FAX makes strange noises, emits smoke or strange smells, unplug it
immediately and contact your local authorised Canon dealer or the Canon help line.
Do not attempt to disassemble or repair the unit yourself.
If you need to contact Canon directly, make sure you have the following information:
Chapter 13
•
Product name
FAXL220 or FAXL295
•
Serial number
The serial number is on the label located at the back of the unit.
•
Place of purchase
•
Nature of problem
•
Steps you have taken to solve the problem and the results
Troubleshooting
1321
Troubleshooting
If You Cannot Solve a Problem
If a Power Cut Occurs
If power is suddenly lost due to a power cut or accidental unplugging, a builtin
battery retains the FAX’s settings. However, any documents stored in memory will
be lost.
During a power cut, functions are limited as follows:
• You cannot make telephone calls from the optional handset. Also, depending on
the telephone, you may not be able to make telephone calls.
• You cannot send, receive, or copy documents.
• You can receive telephone calls from the optional handset or telephone
connected to your unit.
When power is restored, the FAX automatically prints a MEMORY CLEAR
REPORT that lists the documents that were deleted from memory as a result of the
power cut.
27/12 2002 16:48 FAX 123 4567
CANON
001
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
MEMORY CLEAR REPORT
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
MEMORY FILES DELETED
TX/RX NO
0046
0047
MODE
TRANSMIT
B’CAST
0048
DEL SQ BDCST
0049
DELAYED TX
CONNECTION TEL/ID
[
[
[
[
[
[
01]
01]
02]
03]
04]
08]
Canon TOKYO
Canon CANADA
Canon FRANCE
Canon ITALIA
Canon U.S.A.
Canon OPTICS
PGS.
SET TIME
3 27/12
1 27/12
ST. TIME
16:03
16:08
1 27/12
16:15
2 27/12
16:36
20:00
20:00
22:00
If the toner cartridge is empty or there is no paper in the multipurpose tray when power is
restored, the LCD displays CHANGE CARTRIDGE or LOAD PAPER. In these cases, the
MEMORY CLEAR REPORT will not be printed even after the toner cartridge is replaced or
paper is loaded.
1322
Troubleshooting
Chapter 13
Chapter 14
❏
Understanding the Menu System ...............................................................
• Printing a List to Check the Current Settings ........................................
• Accessing the Menus .............................................................................
142
142
143
❏
USER SETTINGS Menu ...........................................................................
144
❏
REPORT SETTINGS Menu ......................................................................
145
❏
TX (Transmission) SETTINGS Menu.......................................................
146
❏
RX (Reception) SETTINGS Menu ............................................................
147
❏
PRINTER SETTINGS Menu.....................................................................
148
❏
POLLING BOX Menu...............................................................................
149
❏
SYSTEM SETTINGS Menu...................................................................... 1410
Summary of Settings
141
Summary of Settings
Chapter 14
Summary of Settings
Understanding the Menu System
The FAX menu system allows you to customise the way your unit operates. It
consists of seven menus, each containing settings that control different functions of
your FAX.
Before adjusting any settings, you may want to print the USER’S DATA LIST to
check the current settings ( below).
Printing a List to Check the Current Settings
You can print the USER’S DATA LIST to check the current settings of your FAX as
well as the registered sender information ( p. 35).
Follow this procedure to print the USER’S DATA LIST:
1
Press Function.
2
Press Report.
3
Use
4
Press OK.
•
or
ACTIVITY REPORT
to select USER DATA LIST.
USER DATA LIST
PRINTING REPORT
The FAX prints the USER’S DATA
LIST.
The sender information is shown at the beginning of the list. The current settings of
the FAX are listed after this.
27/12 2002 17:23 FAX 123 4567
CANON
001
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
USER’S DATA LIST
★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★
1. USER SETTINGS
UNIT TELEPHONE #
UNIT NAME
TX TERMINAL ID
TTI POSITION
TELEPHONE # MARK
SCANNING CONTRAST
OFFHOOK ALARM
VOLUME CONTROL
CALLING VOLUME
KEYPAD VOLUME
ALARM VOLUME
LINE MONITOR VOL.
RX CALL LEVEL
TYPE
142
Summary of Settings
123 4567
CANON
ON
OUTSIDE IMAGE
FAX
STANDARD
ON
2
2
2
2
HIGH
TOUCH TONE
Chapter 14
Accessing the Menus
Follow this procedure to access the different menus:
Press Function.
2
Press Data Registration.
3
Press OK.
4
Use
•
USER SETTINGS
to select the menu you want.
You can select from the following:
– USER SETTINGS ( p. 144)
– REPORT SETTINGS ( p. 145)
– TX SETTINGS ( p. 146)
– RX SETTINGS ( p. 147)
– PRINTER SETTINGS ( p. 148)
– POLLING BOX ( p. 149)
– SYSTEM SETTINGS ( p. 1410)
5
Press OK to access the settings under the
menu you selected.
6
Refer to the appropriate table (
select and register settings:
❏
❏
❏
7
Chapter 14
or
DATA REGSTRATION
Summary of Settings
1
Ex:
ECM RX
following pages) and use these guidelines to
Use
or
to scroll through the settings.
To register a setting or access subsettings, press OK.
To return to a previous level, press Function then Data Registration.
• For your settings to be registered, be sure to press OK after making
a selection or entering information.
• If at any stage you wish to return to standby mode, press Stop.
• If you pause for more than 60 seconds while accessing a menu, the
unit will automatically return to standby mode.
When you are finished, press Stop to return to
standby mode.
Ex:
15:00
FaxOnly
Summary of Settings
143
USER SETTINGS Menu
For details on accessing the settings below, see p. 143.
The selectable settings and the default settings vary depending on the country where you have
purchased the FAX. The values shown here are average values.
Setting
Description
DATE & TIME
Sets the current date and time (
UNIT TELEPHONE #
Enters the fax/telephone number you want to appear at the –
top of each fax page you send (
p. 36).
UNIT NAME
Enters the name or company name you want to appear at
the top of each fax page you send (
p. 36).
–
TX TERMINAL ID
Enables/disables printing of the sender information
(
p. 35).
ON
OFF
Selects whether the sender information is positioned
inside or outside the image area (
p. 35).
OUTSIDE IMAGE
INSIDE IMAGE
TTI POSITION
SubSettings
p. 36).
TELEPHONE # MARK Selects the prefix for the unit number (
–
p. 35).
p. 73).
FAX
TEL
SCAN CONTRAST
Selects the scanning contrast (
OFFHOOK ALARM
Enables/disables the off hook alarm that alerts you that
the handset is not seated properly in its cradle.
ON
OFF
VOLUME CONTROL
Sets the volume of the FAX sounds.
–
CALLING VOLUME
Selects the ring volume when the FAX detects a voice
call.
1/2/3
KEYPAD VOLUME
Selects the keypad touch beep volume.
0 (off)/1/2/3
ALARM VOLUME
Selects the error alarm volume.
0 (off)/1/2/3
LINE MONITOR VOL Selects the line monitor volume (sound during dialling).
0 (off)/1/2/3
STANDARD
DARKER
LIGHTER
RX CALL LEVEL
Selects the ring type for incoming calls.
HIGH
STANDARD
TEL LINE TYPE
Selects the telephone line type setting for your FAX
(
p. 38).
TOUCH TONE
ROTARY PULSE
R-KEY SETTING
Enables dialling through a switchboard.
If you select PBX, you can select additional subsettings
(
p. 39).
PSTN
PBX
144
Summary of Settings
Chapter 14
REPORT SETTINGS Menu
For details on accessing the settings below, see p. 143.
Setting
Description
SubSettings
TX REPORT
Enables/disables automatic printing of a TX
(transmission) REPORT (
p. 114).
PRINT ERROR ONLY: Prints a report only when a
transmission error occurs.
OUTPUT YES: Prints a report every time you send a
document.
OUTPUT NO: No report is printed.
PRINT ERROR ONLY
OUTPUT YES
OUTPUT NO
PRINT WITH IMAGE If you select PRINT ERROR ONLY or OUTPUT YES ON
OFF
above, this setting enables/disables printing of the first
page of the fax under the report.
RX REPORT
Enables/disables automatic printing of an RX (reception) OUTPUT NO
REPORT (
p. 115).
PRINT ERROR ONLY
OUTPUT YES
OUTPUT NO: No report is printed.
PRINT ERROR ONLY: Prints a report only when a
reception error occurs.
OUTPUT YES: Prints a report every time you receive a
document.
ACTIVITY REPORT
Enables/disables automatic printing of an ACTIVITY
REPORT after every 20 transactions (
p. 113).
Chapter 14
AUTO PRINT ON
AUTO PRINT OFF
Summary of Settings
145
Summary of Settings
The selectable settings and the default settings vary depending on the country where you have
purchased the FAX. The values shown here are average values.
TX (Transmission) SETTINGS Menu
For details on accessing the settings below, see p. 143.
The selectable settings and the default settings vary depending on the country where you have
purchased the FAX. The values shown here are average values.
Setting
Description
SubSettings
ECM TX
Enables/disables Error Correction Mode (ECM) during
transmission.
ON
OFF
MID PAUSE SET
Selects the length of a pause entered within a fax/
telephone number with the Redial/Pause button.
2 SEC
(1 to 15)
AUTO REDIAL
Enables/disables automatic redialling if the other party’s
line is busy on the first attempt (
p. 79).
ON
OFF
REDIAL TIMES
Selects the number of redial attempts.
2 TIMES
(1 to 10)
REDIAL INTERVAL
Selects the time interval between redial attempts.
2 MIN.
(2 to 99)
TIME OUT
146
Enables/disables automatic scanning of documents after ON
the fax number is entered.
OFF
ON: Scanning begins automatically five seconds after
entering the fax number (10 seconds if sending to multiple
fax numbers).
OFF: Scanning does not start automatically. (You need to
press Start/Copy to begin scanning.)
Summary of Settings
Chapter 14
RX (Reception) SETTINGS Menu
For details on accessing the settings below, see p. 143.
Setting
Description
SubSettings
ECM RX
Enables/disables Error Correction Mode (ECM) during
reception.
ON
OFF
RX MODE
Selects the receive mode (
Chapter 8).
If you select FAX/TEL AUTO SW, you can select
additional subsettings (
p. 84).
FAX ONLY MODE
NET SWITCH*
FAX/TEL AUTO SW
INCOMING RING
When the RX MODE setting is set to FAX ONLY
MODE or FAX/TEL AUTO SW, this setting enables/
disables ringing when the FAX receives a call.**
OFF
ON
Selects the number of rings before the FAX begins
receiving.
2 TIMES
(1 to 99)
When the receive mode is set to MANUAL MODE, this
setting determines if the FAX switches to fax receive
mode after it rings for a specified time.
OFF
ON
RING COUNT
MAN/AUTO SWITCH
F/T RING TIME
15 SEC
If you select ON above, this setting selects the length of
time the FAX rings before switching to fax receive mode. (1 to 99)
Enables/disables remote receiving.
ON
OFF
If you select ON above, this setting selects the remote
receiving ID.
25
(00 to 99)
MEMORY RX
Enables/disables reception of a document in the FAX’s
memory when a problem occurs during reception.
ON
OFF
RX PAGE FOOTER
Enables/disables printing of the reception date and time, OFF
page number, and transaction number (TX/RX NO.) at the ON
bottom of each received fax page.
REMOTE RX
REMOTE RX ID
*
**
This setting is available for certain countries only.
Even if you have set INCOMING RING to ON, ringing will only occur if you have connected the optional
handset or a telephone to your unit.
Chapter 14
Summary of Settings
147
Summary of Settings
The selectable settings and the default settings vary depending on the country where you have
purchased the FAX. The values shown here are average values.
PRINTER SETTINGS Menu
For details on accessing the settings below, see p. 143.
The selectable settings and the default settings vary depending on the country where you have
purchased the FAX. The values shown here are average values.
Setting
Description
SubSettings
RX REDUCTION
Enables/disables reduction of faxes to fit on the paper
loaded in the multipurpose tray.
ON
OFF
If you select ON, you can select the direction of the
reduction.
VERTICAL ONLY
HORIZ & VERTICAL
Selects the size of the paper loaded in the multipurpose
tray (
p. 56).
A4
LTR
LGL
CUSTOM
PAPER SIZE
If you select CUSTOM, you can select additional
subsettings (
p. 56).
ECONOMY PRT
Enables/disables economy printing (
TONER SUPPLY LOW
Selects whether the FAX continues printing when
RX TO MEMORY
toner level is low (CHANGE CARTRIDGE displayed in KEEP PRINTING
the LCD).
RX TO MEMORY: Stops printing and received faxes are
stored in memory.
KEEP PRINTING: Continues printing even when toner
level is low. Select this setting when you do not have a
new toner cartridge available and need to print any faxes
received in memory.
148
Summary of Settings
p. 58).
OFF
ON
Chapter 14
POLLING BOX Menu
For details on accessing the settings below, see p. 143.
Setting
Description
SubSettings
SETUP FILE
Sets up the polling box to hold a document to be polled
(
p. 911).
–
FILE NAME
Enters the name for the polling box.
–
PASSWORD
Enters a password to restrict access to the polling box
settings.
0000 to 9999
TX PASSWORD
Enters a standard ITUT password.
–
ERASE AFTER TX
Selects whether the document is deleted from memory
once it is polled, or continues to be stored in memory.
ON: Document is deleted from memory after it is polled.
OFF: Document remains in memory after it is polled.
ON
OFF
Changes the polling box settings (
–
CHANGE DATA
PASSWORD
DELETE FILE
PASSWORD
Chapter 14
p. 914).
Enters the password (if registered) to access the polling
box settings.
–
Deletes the polling box settings (
–
p. 914).
Enters the password (if registered) to access the polling
box settings.
Summary of Settings
The selectable settings and the default settings vary depending on the country where you have
purchased the FAX. The values shown here are average values.
–
Summary of Settings
149
SYSTEM SETTINGS Menu
For details on accessing the settings below, see p. 143.
The selectable settings and the default settings vary depending on the country where you have
purchased the FAX. The values shown here are average values.
Setting
Description
UN/LOCK PHONE
Enables/disables restriction of the FAX (
SubSettings
p. 916).
–
LOCK PHONE
Enables/disables restriction of the FAX to make calls and OFF
send faxes.
ON
PASSWORD
Enters a password to restrict access to the LOCK PHONE 0000 to 9999
setting.
RX RESTRICTION
Restricts reception of faxes to the numbers registered for
speed dialling on your FAX (
p. 919).
OFF
ON
If you select ON, you can select additional subsettings.
DATE SETUP
Selects the date format displayed in the LCD and printed
on the faxes you send.
DD/MM YYYY
YYYY MM/DD
MM/DD/YYYY
DISPLAY LANGUAGE
Selects the language of the LCD messages, settings, and
reports.
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
DUTCH
FINNISH
PORTUGUESE
NORWEGIAN
SWEDISH
DANISH
SLOVENE
CZECH
HUNGARIAN
RUSSIAN
TX START SPEED
Selects the speed at which the FAX starts transmitting.
33600bps
14400bps
9600bps
7200bps
4800bps
2400bps
1410
Summary of Settings
Chapter 14
Description
SubSettings
RX START SPEED
Selects the speed at which the FAX starts receiving.
33600bps
14400bps
9600bps
7200bps
4800bps
2400bps
COUNTRY SELECT*
Selects the country where you are using the FAX to
automatically switch the selectable settings and the
default settings to suit the selected country (
p. 28).
UK
GERMANY
FRANCE
ITALY
SPAIN
HOLLAND
DENMARK
NORWAY
SWEDEN
FINLAND
AUSTRIA
BELGIUM
SWITZERLAND
PORTUGAL
IRELAND
GREECE
LUXEMBOURG
HUNGARY
CZECH
RUSSIA
SLOVENIA
SOUTH AFRICA
OTHERS
SUMMER TIME*
Sets the summer time (
OFF
ON
p. 311).
Summary of Settings
Setting
If you select ON, you can select additional subsettings.
*
This setting is available for certain countries only.
Chapter 14
Summary of Settings
1411
1412
Summary of Settings
Chapter 14
Appendix A
Specifications
❏
General Specifications ...............................................................................
❏
Facsimile ....................................................................................................
A2
❏
Copier.........................................................................................................
A3
❏
Telephone...................................................................................................
A3
❏
Printer.........................................................................................................
A3
Specifications
A2
Appendix A
Specifications
A1
General Specifications
Applicable Standards
– Electrical Safety: CE*, GS**
– Radiation: CISPR Pub 22 Class B
– Other: PTT, Energy Star compliant, CE Marking
Power Source
– 200240 V
– 50/60 Hz
ADF Capacity
p. 42
Power Consumption
– Maximum: 500 W
– Standby: Approx. 3.5 W
MultiPurpose Tray Capacity
p. 52
Weight
Approx. 10 kg (With components attached)
Printable Area
p. 53
Dimensions
Scanned Area
p. 42
578 mm
401 mm
Facsimile
445 mm
372 mm
Applicable Line
Public Switched Telephone Network (PSTN)
Compatibility
G3
Data Compressing System
MH, MR, MMR
Modem Type
Fax modem
Modem Speed
33600/31200/28800/26400/24000/21600/19200/
16800/14400/12000/9600/7200/4800/2400 bps
Automatic fallback
404 mm
Transmission Speed
Approx. 3 seconds/page*** at 33.6 Kbps, ECMMMR,
transmitting from memory
Scanning Image Processing
– Ultra High Quality (UHQ™) image enhancement
– Halftones: 64 levels of grey
– Density adjustment 3 levels
578 mm
Environmental Conditions
– Temperature: 10°C32.5°C
– Humidity: 20%80% RH
Liquid Crystal Display (LCD)
16 × 1
Transmission/Reception Memory
FAXL295: Approx. 448 pages***
FAXL220: Approx. 350 pages***
Fax Scanning Speed
Approx. 7.7 seconds/page***
Display Languages
English/French/Spanish/German/Italian/Dutch/
Finnish/Portuguese/Norwegian/Swedish/Danish/
Slovene/Czech/Hungarian/Russian
* This standard is applicable for Europe only.
** This standard is not applicable for Australia.
*** Based on Canon FAX Standard Chart No. 1, standard mode.
A2
Specifications
Appendix A
Dialling
– Automatic dialling
Onetouch speed dialling (15 destinations)
Coded speed dialling (100 destinations)
Group dialling (Max. 114 destinations)
– Regular dialling (with numeric buttons)
– Automatic redialling
– Manual redialling
– Pause button
– Redial button
Networking
– Sequential broadcasting (Max. 116 destinations)
– Automatic reception
– Automatic Fax/Tel switchover
– Delayed transmission (Max. 116 destinations)
– Polling transmission
– Polling reception
– Remote reception by telephone (Default ID: 25)
– Nonring reception
– ECM deactivation
– Network switch*
– ACTIVITY REPORT (after every 20 transactions)
– Nondelivery report
– TTI (Transmit Terminal Identification)
Copier
Telephone
Connection
– Optional handset/telephone*
– Additional telephone/answering machine (CNG
detecting signal)/data modem
Printer
Printing Method
Laser beam printing
Paper Handling
Automatic feed
Paper Size and Weight
p. 52
Recommended Paper
p. 53
Print Speed**
Approx. 6 pages/minute
Specifications
Fax Resolution
– FAX STANDARD: 8 pels/mm × 3.85 lines/mm
– FAX FINE: 8 pels/mm × 7.7 lines/mm
– FAX PHOTO: 8 pels/mm × 7.7 lines/mm with
halftones
– SUPER FINE: 8 pels/mm × 15.4 lines/mm
Print Width
Max. 206 mm
Resolution
600 × 600 dpi
Printing Cartridge
FX3 toner cartridge
Toner Saver
Approx. 30% to 40% reduction in toner
consumption
Scanning Resolution
– Direct Copy: 400 × 300 dpi
– Memory Copy: 200 × 300 dpi
Printing Resolution
600 × 600 dpi
Reduction
70%, 80%, 90%
Copy Speed
Approx. 6 pages/minute
No. of Copies
Max. 99 copies
* This feature is available for certain countries only.
** Based on Canon FAX Standard Chart No. 1, standard mode.
Appendix A
Specifications
A3
A4
Specifications
Appendix A
Appendix B
FAX-L295 Instructions
❏
Introduction................................................................................................
B2
Differences Between the FAXL295 and FAXL220................................
B2
Using Your Documentation .......................................................................
B2
❏
Unpacking the FAXL295 .........................................................................
B2
❏
Connecting the FAXL295 to Your PC .....................................................
B3
❏
Print Media Requirements .........................................................................
• Printable Area ........................................................................................
B4
B4
❏
Selecting Print Media.................................................................................
B5
❏
Loading Envelopes.....................................................................................
B5
❏
Loading Transparencies .............................................................................
B7
FAX-L295
Instructions
❏
❏
Appendix B
FAXL295 Instructions
B1
Introduction
This Appendix provides information relevant only to purchasers of the FAXL295
model. Please be sure to read this section before reading the rest of this guide.
Differences Between the FAX-L295 and
FAX-L220
In addition to the FAXL220 features, the FAXL295 also has the following features:
• Connectability to your PC for printing
• Increased memory for storing up to 448 fax pages*
• Support of a wider range of print media
Using Your Documentation
Your FAXL295 includes the following documentation:
• This guide: Provides detailed information on how to set up, operate, maintain,
and troubleshoot your FAX.
• Printer Driver Guide: This guide, included in the CDROM, describes how to
use your FAX to print from within your PC’s Windows® environment.
Unpacking the FAX-L295
Unpack your FAX as described on page 22. The items included are exactly the same
as for the FAXL220, except that your unit also includes the software necessary for
connecting it to your PC.
Check that you have all items. If any are damaged or missing, notify your local
authorised Canon dealer or the Canon help line immediately.
In addition to the items shipped with your FAX, you will need to purchase a printer cable
to connect your FAX to a PC ( p. B3).
* Based on Canon FAX Standard Chart No. 1, standard mode.
B2
FAXL295 Instructions
Appendix B
Connecting the FAX-L295 to Your PC
To connect your FAX to a PC, you will need to purchase a printer cable that matches
the interface connector on your PC:
• A USB cable no longer than 5 metres
You can purchase the cable from your local authorised Canon dealer.
FAX-L295
Instructions
Follow this procedure to connect the USB cable:
Connect the USB cable to the
FAX and PC during software
installation to ensure proper
operation of the printer driver
(
Printer Driver Guide).
Make sure your PC is running Microsoft Windows® 98/Me or Windows® 2000/XP,
preinstalled by a computer manufacturer on purchase. (The USB port operation also needs
to be assured by the manufacturer.)
Appendix B
FAXL295 Instructions
B3
Print Media Requirements
In addition to the paper listed in Chapter 5, you can also load the following print
media in the multipurpose tray:
Print Media
Size
Quantity
Envelopes
European DL
(220 × 110 mm/
8.66 × 4.33 in.)
7 envelopes
U.S. Commercial No. 10
(241.3 × 104.1 mm/
9.5 × 4.1 in.)
7 envelopes
A4, Letter
1 sheet
Transparencies
Please refer to Chapter 5 for full details on paper handling, loading paper, and
selecting paper delivery.
Printable Area
The shaded area shows the printable area of European DLsize envelopes.
For the printable area of paper, see Chapter 5.
MAX. 4 mm
MAX. 4 mm
MAX. 4 mm
FEED
DIRECTION
MAX. 10 mm
B4
FAXL295 Instructions
Appendix B
Selecting Print Media
Follow these guidelines when selecting envelopes and transparencies:
For paper guidelines, see Chapter 5.
•
Envelopes
Use standard envelopes with diagonal seams and flaps.
To prevent jams in the multipurpose tray, do not use the following:
– Envelopes with windows, holes, perforations, cutouts, and double flaps
– Envelopes made with special coated paper or deeply embossed paper
– Envelopes with peeloff sealing strips
– Envelopes with letters enclosed
You may be able to load other size envelopes than those listed on the previous
page. However, Canon cannot guarantee consistent performance on these.
When printing on envelopes, be sure to use faceup delivery (
■
•
•
•
p. 54).
Transparencies
Use only special laser printer transparencies.
When printing on transparencies, be sure to use faceup delivery ( p. 54).
To prevent the transparency from curling, remove it as soon as it exits the FAX and
place it on a flat surface to cool.
Loading Envelopes
Follow this procedure to load up to 7 envelopes in the multipurpose tray:
1
Prepare the envelopes.
❏
Appendix B
Arrange the stack of envelopes on a
firm, clean surface, and press down
firmly on the edges to make the folds
crisp.
• Press all the way around the
envelopes to remove any curls
and expel air from inside the
envelopes. Also, press firmly on
the area that corresponds to the
edges of the back flap.
FAXL295 Instructions
B5
FAX-L295
Instructions
■
•
•
❏
Remove any curling from the
envelopes by holding the edges
diagonally and bending them gently.
❏
Run a pen or other rounded object
along the back flaps to flatten them.
• The flaps should not bulge more
than 5 mm.
2
Remove the multipurpose tray cover
from the FAX.
3
Insert the stack into the multipurpose
tray ~ (print side facing you), then
adjust the paper guides to the width of
the stack Ä.
FLAP
1
2
2
B6
FAXL295 Instructions
Appendix B
4
Replace the multipurpose tray cover.
• Be sure to replace this cover to
prevent dust accumulating inside
the unit.
5
Adjust the paper delivery selector to
(faceup delivery). For details, see p. 54.
The FAX is now ready to print.
Loading Transparencies
FAX-L295
Instructions
Load transparencies in the multipurpose tray as for paper. For details, see p. 215.
Appendix B
FAXL295 Instructions
B7
B8
FAXL295 Instructions
Appendix B
Appendix C
Options
Optional Handset........................................................................................
• Package Contents...................................................................................
• Attaching the Handset to Your FAX .....................................................
• Maintaining Your Handset ....................................................................
C2
C2
C3
C4
Options
❏
Appendix C
Options
C1
Optional Handset*
An optional handset is available in certain countries for connection to your FAX.
Contact your local authorised Canon dealer for more information on purchasing this
option.
Please note that the shape of your handset may differ from the one shown in this section.
However, both handsets have exactly the same functions and performance.
Package Contents
Make sure your handset package includes the following items:
HANDSET CRADLE
HANDSET
SCREWS WITH PLUGS (2)
SCREWS
(Not used with your FAX.)
RINGER VOLUME SWITCH
Use a pen or other pointed
object to select the ring
volume of the handset
(HI, LO, or OFF).
If any items are damaged or missing, notify your local authorised Canon dealer or the
Canon help line immediately.
* The optional handset is available for certain countries only.
C2
Options
Appendix C
Attaching the Handset to Your FAX
Follow this procedure to attach the handset to your FAX:
1
Use a screwdriver to remove the two
covers on the left side of the unit.
2
Remove the screws from the plugs and
insert the plugs into the holes on the
handset cradle.
3
Insert the plugs (with the handset
cradle) into the holes on the unit.
•
Use your finger to push the screws
into the plugs.
•
•
5
Appendix C
If you have difficulty, use a cross
point screwdriver to push the
screws all the way into the plugs.
(Do not screw them in as the
screws may break.)
Make sure you support the unit
when inserting the screws.
Options
4
If you have difficulty inserting the
plugs, turn the unit so that the left
side is facing you and the right side
is against a wall. You can now
insert the plugs without the unit
moving.
Place the handset in its cradle and
connect the handset cord to the
jack.
Options
C3
Maintaining Your Handset
To maintain your handset in top working condition, be sure to follow these
guidelines:
• Do not leave your handset exposed to direct sunlight.
• Do not install your handset in hot or humid conditions.
• Do not spray aerosol polishes on your handset since they may enter the holes on
your handset and cause damage.
• Use a damp cloth to clean your handset.
C4
Options
Appendix C
Index
A
A4 setting 52, 56, 148
ACTIVITY REPORT
description 112
printing 113
sample 113
setting 145
ADF 210
adding pages in 44
capacity 42
definition 12
jams in 132
ALARM VOLUME setting 144
ANS.MACHINE MODE
description 82
setting 89
Answering machine
connecting 25, 26
using with FAX 89
Area
printable 53
scanned of document 42
Assembling, FAX 24
AUTO REDIAL
message 138
setting 710, 146
Automatic Document Feeder. See ADF
Automatic redialling
cancelling 79, 710
definition 79
setting options for 710, 711
B
Broadcasting, sequential 712, 713
BUSY/NO SIGNAL message 138
C
C (Clear) button 211, 34
CALLING VOLUME setting 144
Cancelling
polling receiving 911
receiving 811
redialling 79, 710
restriction of your FAX 917, 918
sending 78
Cartridge. See Toner cartridge
CHANGE CARTRIDGE message 126, 138
CHANGE DATA setting 915, 149
CHECK COVER message 139
CHECK DOCUMENT message 132, 139
CHECK PAPER SIZE message 139
CHECK POLLING ID message 139
CHECK PRINTER message 139
CHK SUBADDR/PSWD message 1310
Cleaning
FAX’s exterior 122
FAX’s interior 123, 124
scanner components 124, 125
CLEAR PAPER JAM message 133, 1310
Coded Dial button 211, 62, 614
CODED SPEED DIAL LIST 1
description 112
printing 617
sample 619
CODED SPEED DIAL LIST 2
description 112
printing 617
sample 619
Coded speed dialling 62, 74
making telephone call with 615
registering 67 to 610
sending with 614
Components, FAX 210, 211. See also individual
component names
Connecting
answering machine 25, 26
data modem 25, 26
external device 25, 26
handset 25
power cord 27
telephone 25, 26
telephone line cord 25
Index
button 211, 143
button 211, 34
button 211, 34
button 211, 143
( p. nnn), definition 12
1TOUCH SPD DIAL LIST 1
description 112
printing 617
sample 618
1TOUCH SPD DIAL LIST 2
description 112
printing 617
sample 618
I1
Contrast 73
Conventions, type 12, 13
Copying 102, 103
document requirements 42
problems 1317
quick 103
Cord
answering machine 25, 26
data modem 25, 26
power 22, 27
telephone 25, 26
telephone line 22, 27
Correcting mistake 34
COUNTRY SELECT setting 28, 1411
Cover
front 210
multipurpose tray 22, 24, 210
CUSTOM setting 56, 148
CUSTOM1/LONG setting 52, 57
CUSTOM2/SHORT setting 52, 57
Customer support 13
D
Data
modem, connecting 25, 26
Registration button 211, 143
Date, entering 36
DATE & TIME setting 36, 144
DATE SETUP setting 1410
Default, definition 12
DEFAULT ACTION setting 85, 86
Delayed sending
deleting document set for 717
printing document set for 716
scanning a document into memory for 714, 715
Transmission button 211, 714, 716, 717
DELETE FILE setting 915, 149
Deleting
document in memory 98
document set for delayed sending 717
polling box settings 914, 915
Delivery, paper. See Paper delivery
Destination labels 22, 66, 613
Dialling
coded speed dialling. See Coded speed dialling
methods 74
regular 74
special 92, 93
switching temporarily to tone 93
through switchboard 39, 310
Directory 616
DISPLAY LANGUAGE setting 28, 1410
DOC. MEMORY LIST
description 112
printing 94
sample 94
setting 94
I2
DOC. TOO LONG message 1310
Document
adding pages in ADF 44
definition 12
guide 210
loading 43, 44
problem 42
problems with multipage 43
quantity 42
requirements 42
scanned area 42
size 42
support 22, 24, 210
thickness 42
weight 42
Documentation 22
E
ECM, definition 12
ECM RX
message 1310
setting 147
ECM TX
message 1310
setting 146
ECONOMY PRT setting 58, 148
ERASE AFTER TX setting 913, 149
ERROR TX REPORT, sample 114
Ex:, definition 12
External device
connecting 25, 26
F
F/T RING TIME setting 85, 86, 147
Facedown delivery 54, 55
slot 210, 54
Faceup delivery 54, 55
slot 210, 54
Fax, definition 12
FAX 22
assembling 24
cleaning 122 to 125
clearing jams 132 to 137
components 210, 211. See also individual
component names
connecting 25 to 27
name, registering 36, 37
number, registering 36, 37
restricting use 916 to 918
testing 216
unpacking 22, 23
FAX ONLY MODE
description 82
setting 82, 83, 147
FAX/TEL AUTO SW setting 84, 147
G
G3, definition 12
GROUP DIAL LIST
description 112
printing 617
sample 620
Group dialling 62, 74
registering 611 to 613
sending with 614
Guide
document 210
paper 210
H
Handling, safety instructions 14, 15
Handset
connecting 25
sending manually via 76, 77
Hook Button 211, 615, 76, 93
HOOKING setting 39, 310
HORIZ & VERTICAL setting 148
I
INCOMING RING setting 147
INSIDE IMAGE setting 144
Installing, toner cartridge 212 to 214
ITUTS, definition 12
J
Jack 25, 26
Jams
clearing 132 to 137
in ADF 132
in paper delivery slots 133
inside unit 133 to 137
paper 133 to 137
K
KEEP PRINTING setting 148
KEYPAD VOLUME setting 144
L
Label
destination 22, 66, 613
paper loading warning 22, 24
Latch 210
LCD 211
definition 12
messages 138 to 1312. See also individual message
names
Letter mode
lowercase 32, 33
uppercase 32, 33
Letters, entering 32, 33
Lever, paper release 210, 134
LGL setting 52, 56, 148
LINE MONITOR VOL setting 144
Lists. See also individual list names
summary 112
LOAD PAPER message 1310
Loading
document 43, 44
paper 215, 216
Location, safety instructions 15, 16
LOCK PHONE setting 916, 917, 1410
Lowercase letter mode 32, 33
LTR setting 52, 56, 148
M
Maintenance, safety instructions 14, 15
MAN/AUTO SWITCH setting 147
MANUAL MODE
description 82
setting 87, 88
Manual redialling 79
cancelling 79
Manual sending via the handset 76, 77
cancelling 78
Manual setting. See MANUAL MODE
Memory
deleting document in 98
documents in 94 to 98
printing document in 95
printing list of documents in 94
receiving when problem occurs 810
Reference button 211, 94, 95, 96, 98
scanning a document for delayed sending into
715
sending. See Memory sending
sending document in 96, 97
MEMORY CLEAR REPORT 1322
description 112
sample 1322
MEMORY FULL message 1310
MEMORY RX setting 147
Memory sending 75, 76
cancelling 78
MEMORY USED nn% message 1311
Menu. See also individual menu names
accessing 143
definition 12
system, understanding 142, 143
714,
Index
Fax/Tel Mode
description 82
setting 84
setting options for 85, 86
FaxAbility. See Telecom FaxAbility
FaxStream™ Duet. See Telstra FaxStream™ Duet
FILE NAME setting 912, 149
Fixing assembly 210
Front cover 210
Function Button 211, 36
FX3. See Toner cartridge
I3
Messages. See LCD messages
MID PAUSE SET setting 146
Mistake, correcting 34
MULTI TX/RX (Transaction) REPORT 115
description 112
sample 115
MULTI TX/RX REPORT. See MULTI TX/RX
(Transaction) REPORT
Multipurpose tray 210
capacity 52
cover 22, 24, 210
N
NO RX PAPER message 1311
NO TEL # message 1311
NOT AVAILABLE message 1311
Number
entering 32, 33, 34
mode 32, 33, 34
Numeric buttons 211, 32
O
OFFHOOK ALARM setting 144
Ok button 211, 143
Onetouch speed dialling 62, 74
buttons 211, 62, 614
making telephone call with 615
registering 63 to 66
sending with 614
Operation panel 210, 211
Optional handset. See Handset
OUTPUT NO setting 145
OUTPUT YES setting 145
OUTSIDE IMAGE setting 144
P
Paper
delivery. See Paper delivery
feeding problems 1313
guide 210
jams 133 to 137
loading 215 to 216
loading warning label 22, 24
path 54
printable area 53
quantity 52
release lever 210, 134
requirements 52, 53
rest 22, 24, 210
selecting 53
size setting 52, 56, 57
weight 52
I4
Paper delivery
facedown 54, 55
faceup 54, 55
selecting 54, 55
selector 210, 55
slot, jams in 133
PAPER SIZE setting 56, 148
Password
for polling box, setting 911 to 913
for polling receiving 99
registering for coded speed dialling 67 to 610
registering for onetouch speed dialling 63 to 66
PASSWORD setting 912, 916, 917, 149, 1410
Pause, entering 92
PBX
definition 39
setting 39, 144
Polling
another fax machine 99, 910
box. See Polling box
button 211, 910, 914
definition 99
receiving. See Polling receiving
sending. See Polling sending
Polling box
changing settings 914, 915
deleting settings 914, 915
scanning document into 914
setting up 911 to 913
POLLING BOX
menu 143, 149
setting 911 to 915
Polling receiving
cancelling 911
polling another fax machine 99, 910
Polling sending
changing polling box settings 914, 915
deleting polling box settings 914, 915
scanning document into polling box 914
setting up polling box 911 to 913
Power
cord 22, 27
cut 1322
supply, safety instructions 16
switch 27
PREFIX setting 39, 310
PRINT ERROR ONLY setting 145
PRINT WITH IMAGE setting 145
PRINTER SETTINGS menu 143, 148
Printing
area 53
document in memory 95
document set for delayed sending 716
lists. See individual list names
problems 1318, 1319
reports. See individual report names
93
Q
Quantity
document 42
paper 52
R
R button 211
registering 39, 310
REC’D IN MEMORY message 810, 1312
Receive Mode button 211
Receiving. See also individual receive modes
cancelling 811
in memory when problem occurs 810
methods 82
polling. See Polling receiving
problems 1315 to 1317
remote, definition 87
restricting 919
while performing other tasks 810
Reception report. See RX (Reception) REPORT
REDIAL INTERVAL setting 711, 146
REDIAL TIMES setting 711, 146
Redial/Pause button 211, 79, 92
Redialling 79 to 711
Remote reception, definition 87
REMOTE RX ID setting 147
REMOTE RX setting 147
Replacing
toner cartridge 126 to 128
Report button 211, 617, 113, 142
REPORT SETTINGS menu 143, 145
Reports. See also individual report names
summary 112
Resolution
button 211, 72, 102
copying, setting 102
sending, setting 72
Rest, paper 22, 24, 210
Restricting
reception 919, 920
use of FAX 916 to 918
RING COUNT setting 147
RING START TIME setting 85, 86
RKEY SETTING 39, 144
Roller, transfer charging 210
ROTARY PULSE setting 38, 144
RX, definition 12
RX (Reception) REPORT 115
description 112
sample 115
RX (Reception) SETTINGS menu 143, 147
RX CALL LEVEL setting 144
RX MODE setting 83, 84, 147
RX PAGE FOOTER setting 147
RX REDUCTION setting 148
RX REPORT. See also RX (Reception) REPORT
setting 145
RX RESTRICTION setting 919, 1410
RX SETTINGS menu. See RX (Reception) SETTINGS
menu
RX START SPEED setting 1410
RX TO MEMORY setting 148
S
Safety instructions 14 to 16
Saving, toner consumption 58
SCAN CONTRAST setting 73, 144
Scanner components, cleaning 124, 125
Scanning
contrast, copying 73
contrast, sending 73
document area 42
document for delayed sending into memory
715
resolution, copying 102
resolution, sending 72
SELECT POL REJCT message 1312
Selector, paper delivery 210, 55
Sender information
definition 35
registering 35 to 37
sample 35
714,
Index
Problems
cannot solve 1321
copying 1317
document 42
general 1320
multipage document 43
paper feeding 1313
printing 1318, 1319
receiving 1315 to 1317
receiving into memory when 810
sending 1313 to 1315
telephone 1318
PSTN setting 39, 144
PSWD POLL REJECT message 1311
PSWD TX REJECTED message 1311
Pulse dialling
setting for 38
switching temporarily to tone dialling
I5
Sending
at preset time. See Delayed sending
cancelling 78
delayed. See Delayed sending
document in memory 96, 97
document requirements 42
manual via the handset 76, 77
memory 75, 76
methods 75 to 77
polling. See Polling sending
problems 1313 to 1315
same document to several fax numbers 712, 713
timer. See Delayed sending
with coded speed dialling 614
with group dialling 614
with onetouch speed dialling 614
with speed dialling 614
Sequential broadcasting 712, 713
Serial number, FAX 1321
Settings. See also individual setting names
printing list of 142
SETUP FILE setting 912, 149
Shipping materials, removing 24
Size
document 42
paper 52, 56, 57
Space button 211, 33, 34
Special function buttons 211. See also individual button
names
Speed dialling. See also individual speed dialling methods
definition 62
lists. See Speed dialling lists
making telephone call with 615
methods 62
sending document with 614
using 614, 615
Speed dialling lists. See also individual list names
printing 617 to 620
samples 618 to 620
Start/Copy button 211, 102, 103
Stop button 211, 143
SUBADD TX REJECT message 1312
Subaddress
for polling receiving 99
registering for coded speed dialling 67 to 610
registering for onetouch speed dialling 63 to 66
SUMMER TIME setting 311, 1411
Support
customer 13
document 22, 24, 210
tray 22, 24, 210
Switchboard, dialling through 39, 310
Symbols, entering 32, 34
SYSTEM SETTINGS menu 143, 1410
I6
T
T( ) button 93
TEL LINE TYPE setting 38, 144
Telephone
connecting 25, 26
making call with speed dialling 615
problems 1318
TELEPHONE # MARK setting 144
Telephone line
cord 22, 25
type, setting 38
Testing FAX 216
Thickness, document 42
Time
entering 36
sending at preset. See Delayed sending
TIME OUT setting 146
Timer sending. See Delayed sending
Tone dialling
setting for 38
switching temporarily to 93
Toner cartridge 22
compartment 210
installing 212 to 214
replacing 126 to 128
Toner saver setting 58
TONER SUPPLY LOW setting 148
TOUCH TONE setting 38, 144
Transfer charging roller 210
Transmission report. See TX (Transmission) REPORT
Tray
multipurpose 210
multipurpose, cover 22, 24, 210
support 22, 24, 210
TTI POSITION setting 144
TX, definition 12
TX (Transmission) REPORT 114
description 112
sample 114
TX (Transmission) SETTINGS menu 143, 146
TX PASSWORD setting 912, 149
TX REPORT. See also TX (Transmission) REPORT
setting 145
TX SETTINGS menu. See TX (Transmission) SETTINGS
menu
TX START SPEED setting 1410
TX TERMINAL ID setting 144
TX/RX CANCELLED message 1312
TX/RX NO., definition 12
TX/RX NO. nnnn message 1312
TX/RX NO. nnnn, SCANNING P.nnn, MEMORY FULL
message 1312
Type conventions 12, 13
U
UN/LOCK PHONE setting 916, 917, 1410
UNIT NAME setting 37, 144
UNIT TELEPHONE # setting 37, 144
Unpacking FAX 22, 23
Uppercase letter mode 32, 33
USER SETTINGS menu 143, 144
USER’S DATA LIST
description 112
printing 142
sample 142
User’s Guide, type conventions 12, 13
V
VERTICAL ONLY setting 148
Volume
ALARM VOLUME setting 144
CALLING VOLUME setting 144
KEYPAD VOLUME setting 144
LINE MONITOR VOL setting 144
VOLUME CONTROL setting 144
W
Index
Weight
document 42
paper 52
unit 15
I7
I8
Download PDF

advertising