Instruction manual | Canon HFM300 Camcorder User Manual

20” TV/DVD/VCR Combo
TBX-2000AF
Instruction Manual
Instruction ManualManual
WARNING
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
CAUTION
Caution: To reduce the risk of electric shock, do not
remove cover (or back). No user serviceable parts
inside. Refer servicing to qualified service personnel.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates "dangerous voltage"
inside the product that presents a risk of
electric shock or personal injury.
This symbol indicates important
instructions accompanying the product.
Caution: To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Attention: Pour é viter les chocs é lectriques, introduire la lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqú au fond.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT STARE INTO
BEAM.
The unit employs a Laser System. To prevent direct exposure to the laser beam, do not try to open the
enclosure. Visible laser radiation when open and interlocks defeated.
Refer to the identification/rating label located on the back panel of your product for its proper operating
voltage.
Caution: Using video games or any external accessory with fixed images for extended periods of time
can cause them to be permanently imprinted on the picture tube (or projection TV picture tubes).
ALSO, some network/program logos, phone numbers, etc. may cause similar damage. This damage
is not covered by your warranty.
Cable TV Installer
This reminder is provided to call your attention to Article 820-40 of the National Electrical Code (Section 54
of the Canadian Electrical Code, Part 1) which provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system of the building as close to the
point of cable entry as practical.
Customer Record
You will find the model number and chassis number of your unit on the back of your unit. Record these
numbers in the spaces provided below. Refer to them whenever you call customer service or your dealer
regarding this product.
Chassis Number:
Model Number:
PACKING LIST
Parts
QTY
TV/DVD/VCR Combo
1
Remote Control
1
Operation Manual
1
AAA Alkaline Batteries
2
1
Instruction ManualManual
IMPORTANT SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or third prong is provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11.Only use attachments/accessories specified by the manufacturer.
12.Use only the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13.Unplug this apparatus during lightning storms or when unused for long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15.Warning - This unit should only be serviced by an authorized and properly trained technician.
Opening the cover or other attempts by the user to service this unit may result in serious injury
or death from electrical shock, and may increase the risk of fire.
FCC Warning
Class B Computing Device
Information to User
This equipment has been tested and found to comply with the limits for a Class B Digital Device pursuant
to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. lf this equipment receives interference while off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) lncrease the separation between the equipment and unit.
3) Connect the equipment into an outlet on a circuit different from that to which the unit is connected.
4) Consult the dealer or an experienced radio/TV technician for help and for additional suggestions.
The user may find the following booklet prepared by the Federal Communications Commission helpful:
"How to Identify and Resolve Radio - TV Interference Problems". This booklet is available from the US
Government Printing Office. Washington, D.C. 20402, Stock No. 004-000-00345-4.
FCC Warning
The user is cautioned that changes or modifications not expressly approved by the manufacturer could void
the user's authority to operate the equipment.
NOTE: In order for an installation of the product to maintain compliance with the limits for a Class B
Device, shielded cables must be used.
2
Instruction ManualManual
WARNING:
THE REGION CODE FOR THE UNIT IS 1.
CLASS 1
LASER PRODUCT
Since it is very usual for DVD movies to be released at different times in different regions
of the world, all players have region codes and disks can have an optional region code. If
you load a disk of a different region code to your player, you will see the region code notice
on the screen. The disk will not play, and should be unloaded.
Notes on Discs
HOW TO HANDLE, CLEAN, AND STORE DISCS.
Handling discs
•DO NOT TOUCH THE PLAYBACK SIDE OF THE DISC.
•DO NOT ATTACH PAPER OR TAPE TO DISCS.
Note:
Polaroid SHALL NOT BE RESPONSIBLE FOR DAMAGE
THAT MAY OCCUR TO A DISC FROM BEING OPERATED IN THE UNIT.
Cleaning discs
•Fingerprints and dirt on the disc cause picture and sound deterioration.
Wipe the disc from the center outward with a soft cloth. Always keep the disc clean.
•If you cannot wipe off the dirt off, wipe the disc lightly with a slightly moistened soft cloth and finish
with a dry cloth.
•Do not use any of solvent such as paint thinner, benzine, commercially available cleaners or anti-static
spray for vinyl LP's.
Storing discs
•Do not store discs in places subject to direct sunlight or near heat sources.
•Do not store discs in places subject to moisture and dust.
•Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause
warping.
Playable discs
This unit can play back the following discs.
Disk Mark
Contains
Disc Size Maximum playback time
Approx. 4 hours
(single sided disc)
DVD
video
disc
Audio
+Video
(moving
pictures)
KODAK
Picture
CD
Spec.
12cm
MP3 CD
Audio
12cm
VHS
Audio
+Video
12cm
Approx. 8 hours
(double sided disc)
Up to 10 hours
Notes on regional numbers
DVDs are divided into separate regions. The United States and Canada are designated as region 1
DVD.
Your unit plays region 1 DVDs only.
3
Instruction ManualManual
TABLE OF CONTENTS
INTRODUCTION
Safety Precautions ..........................................................................................................................1
Feature Descriptions ......................................................................................................................5
Specifications ..................................................................................................................................5
Front and Rear Unit Profiles ..........................................................................................................6
Remote Control Features ................................................................................................................6
INSTALLATION
Connecting the Antenna ..................................................................................................................8
Installing the Remote Control Batteries ..........................................................................................8
Connecting A/V Equipment ............................................................................................................9
FUNCTIONS & FEATURES
Turn On/Off ....................................................................................................................................11
Basic Functions ............................................................................................................................11
Function Selection Menus
Picture Menu ..........................................................................................................................11
Sound Menu............................................................................................................................11
Tuner Menu ............................................................................................................................12
TV Timer Menu ......................................................................................................................12
General Menu ........................................................................................................................12
Useful Remote Control Features ..................................................................................................14
DVD FUNTIONS
Playing Back a Disc ......................................................................................................................15
Using the On-Screen Display ........................................................................................................16
Locating a Specific Title, Chapter or Track ....................................................................................17
Playing Repeatedly ......................................................................................................................17
Selecting Subtitles ........................................................................................................................18
Selecting the Camera Angles/Language/Audio Settings ..............................................................18
Playing Back Your Kodak Picture CD ............................................................................................19
MP3 Operation ..............................................................................................................................19
Setting the Parent Lock ................................................................................................................20
Customizing the Function Selectings ............................................................................................21
VCR FUNTIONS
VCR Playback ..............................................................................................................................22
Recording ......................................................................................................................................22
Search Function ............................................................................................................................23
VCR Setting ..................................................................................................................................23
Other Remote Control Features ....................................................................................................24
TROUBLESHOOTING GUIDE.............................................................................................................25
4
Instruction ManualManual
Feature Descriptions
181 Channel Tuner - Total number of channels the TV can receive: 2-69 in Air mode, or 1-125 in Cable
mode
AV Input (Front) - Input designed for infrequent use, such as with a camcorder or video game unit
S-Video Input (Front) - Input designed for greater clearity and sharpness
AV Input (Rear) - Standard composite input designed for use with A/V devices, such as a DVD player
AV Output (Rear) - Output signals from TV to devices such as VCR's
RF IN Jack - Standard coaxial antenna jack
Channel Recall - Instant return to the last channel viewed
Closed Captions Display -Feature that displays the closed captions or text of a TV broadcast
Remote Control - A wireless remote control unit for the TV
On/Off Timer - Feature that allows the user to set a time for the TV to turn on or off
Parental Control - Feature that allows parents to block out selected types of programming
Screen Size - The diagonal size of the TV screen
Selectable Picture Modes - Preset standards for TV display: User, Normal, Movie and Sports
Selectable Sound Modes - Preset standards for TV sound: User, Normal, Speech Movie and Music
MTS Stereo/Video Stereo- Stereo sound for superior TV viewing experience
Trilingual On Screen Display (OSD) - TV's on screen display can be either English, French or Spanish
DVD/CD/MP3/KODAK Picture CD Support
SPECIFICATIONS
MODEL
TDX-2000AF
Television System
NTSC-M
Channel Coverage
VHF 2-13, UHF 14~69
Cable TV Coverage
Mid Band (A-8~A-1, A~I);
Super Band (J~W)
Hyper Band (AA~ZZ, AAA, BBB)
Ultra Band (65~94, 100~125)
Channels Preset
181
Antenna Input
75 ohm (unbalanced)
Screen Dimensions
15.98 x 12.01 in.
406 x 305 mm
Audio Output
2W + 2W
Total Harmonic Distortion
<7%
Power Source
~120Vac, 60Hz
Unit Weight
68.2 lbs. (31 kg)
Unit Dimensions
22.91 x 21.06 x 19.37 in.
582 x 535 x 492 mm
Packaged Dimensions
26.38 x 24.88 x 22.64 in.
670 x 632 x 575 mm
Power Consumption
130W
5
Instruction ManualManual
Front and Rear Unit Profiles
Front panel
1
1 AV IN1 JACK
2 VCR DECK
3 STOP/EJECT
4 PLAY/PAUSE
5 FAST REVERSE
6 FAST FORWARD
2
3 4 5 6 7
8 9 10
11 12 13
7 REC/OTR
8 TIMER REC INDICATOR
9 REC/OTR INDICATOR
10 POWER INDICATOR
11 TV/VIDEO SELECT
12 MENU SELECT
14
15 16 1718
19
20
13 VOLUME DOWN/UP
14 CHANNEL DOWN/UP
15 DISC TRAY
16 OPEN/CLOSE
17 PLAY/PAUSE
19 REMOTE SENSOR
18 STOP
20 STANDBY
Rear panel
ANTENNA IN
Remote Control Features
6
Instruction ManualManual
Remote Control Features
The keys marked with * have composite functions.
No.
Button
1
Function Description
TV
DVD
VCR
DVD
To enter DVD mode
——
To enter DVD mode
2
TV/VCR
——
To shift to TV/AV mode
——
3
0~9
Channel number (0~9)
Number (0~9)
4
VIDEO
TV/Video select
——
5
PICTURE
6
DVD SET UP
——
DVD setup
——
*7
CH-/+(TRK-/+)
Channel down/up
——
Tracking adjust
*8
C C (SUB-T)
CCD/Text
Sub title
CCD/Text
*9
MTS/SAP(AUDIO)
Stereo/SAP
Audio
Hi Fi select
*10
ANGLE(SKIP)
——
Angle select
Skip forward
11
REPEAT
——
Repeat playback
*12
PAUSE(STEP)
To pause during recording
Step
——
To make picture advance frame
by frame in the Still mode
/To pause during recording
13
SPEED
To select speed of tape
——
14
OTR
One touch record
——
15
PLAY/PAUSE
To play
Play/Pause
Play/Still
*16
PREV(VCR SEARCH)
VCR search
Previous skip
VCR search
*17
NEXT(VCR TIMER)
VCR timer
Forward skip
VCR timer
Picture mode select
18
Standby
19
MUTE
Mute on/off
20
SOUND
Sound mode select
21
TV/VCR MENU
TV menu select
22
¡Ä
¡Å
<>/ENTER
To navigate the menus/ To access the sub menus
23
VOL-/VOL+
Volume down/up
*24
TV RECALL(TITLE)
Channel r ecall
Title
——
*25
TV SCAN (D.MENU)
Channel scan
DVD menu
——
26
DISPLAY
27
*28
A-B
COUNTER RESET
(CLEAR)
29
SLEEP
30
EJECT
31
STOP
32
FWD
33
REV
On-screen display
——
To repeat playback from point A to point B
Counter reset
To clear a program in the TIMER RECORDING menu
Sleep off
To eject t ape
Open/Close
To eject t ape
Stop
FF
FWD
REW
CUE1/CUE2
REV1/REV2
When " " displayed during DVD playback, the function is not operational.
7
Instruction ManualManual
INSTALLATION
- Please read the safety instructions in this manual completely before installation.
- Install your unit in an area where direct sunlight will not fall upon the screen.
- Soft, indirect light is best for television viewing.
- Allow enough space (at least 4 in.) between the TV and any walls or enclosures for proper ventilation.
- Optimum television viewing distance is 3-5 times the screen's size.
Auto-Degaussing
Color TV is easily affected by magnetism which leads to color distortion. If your unit is moved or affected by
near magnetic components or appliances with power on, please power off your unit for at least 1 hour. The
built-in auto-degaussing circuit will eliminate the magnetism interference.
Auto off when no signal received
The TV set will automatically enter into Standby mode when the following conditions are met.
1.TV is in antenna mode.
2.Current channel has no signal.
3.No key is pressed within 15 minutes.
Connecting the Antenna
75-ohm coaxial cable (not supplied)
VHF
UHF
or Cable
OR
300-ohm twin-lead cable (not supplied)
Antenna adapter
(not supplied)
VHF
RF Input
(back of TV unit)
OR
U/V mixer
(not supplied)
UHF
Notes:
1) It is recommended that a 75 ohm coaxial cable be used in order to eliminate interference and noise which
may occur due to nearby radio transmissions.
2) The antenna cable should not be tied together with other wiring.
3) Set up a lightning rod and check it regularly when an outdoor antenna is used.
Installing the Remote Control Batteries
1. Remove the battery compartment lid.
2. Insert two AAA batteries (included). Make sure the positive (+) and negative (-) polarities are correctly aligned.
3. Reattach the battery lid.
Notes:
1) Alkaline batteries are recommended for longer life.
2) Always replace both batteries at the same time.
3) Do not expose batteries to fire or break them open.
4) To avoid battery leakage, remove batteries from the remote control when it is not being used for a long period
of time.
8
Instruction ManualManual
INSTALLATION (continued)
Connecting A/V Equipment
The following are diagrams showing basic instructions for attaching external equipment, like a VCR or
DVD player, to your unit. Please refer to operation manuals of external audio/video equipment that will
be connected to your set for additional instructions. PLEASE TURN OFF ALL POWER BEFORE
CONNECTING DEVICES TOGETHER.
Connect VCR's RF OUT terminal to the RF IN jack located on the rear panel of the TV.
Coaxial Cable
RF IN
VCR
Input from Device to TV
AUDIO/VIDEO OUT
DO NOT connect both composite (yellow video terminal) and S-Video terminal. Use only
one of the two. Also, remember to connect the audio cables when using S-Video.
DVD Player
With S - VIDEO Terminal
Yellow
Red
Camcorder
VIDEO
Yellow
Red
AUDIO
White
White
VCR
Output from TV to Device
AUDIO/VIDEO IN
Yellow
Red
VIDEO
Yellow
Red
AUDIO
White
White
VCR
9
Instruction ManualManual
INSTALLATION (continued)
Connecting A/V Equipment (continued)
Enjoying Digital Stereo Sound (Digital Stereo)
Enjoy the dynamic sound of Digital Stereo by connecting
an amplifier equipped with a digital audio input and speaker
system (right and left front speakers).
Set "SPDIF Output" to "SPDIF/PCM" via the setup menu.
Enjoy DTS
DTS programming can deliver surround sound with five
discrete full range channels plus a sixth channel for a
subwoofer. You can enjoy your unit with a DTS Digital
Surround Sound System. All you need is to connect your
unit to a DTS receiver with an external decoder.
•How to setup the sound output:
From the "General Setup Page" display, set "SPDIF
Output" to "SPDIF/RAW".
This product incorporates copyright protection technology
that is protected by method claims of certain U.S. patents
and other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
viewing uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
It is forbidden by law to copy, broadcast, show, play in
public, or rent copyrighted material without permission.
DVD video discs are copy protected, and any recordings
made from these discs will be distorted.
Notes:
(1) Do not connect the PCM/BITSTREAM jack of the
unit to the AC-3 RF input of a Dolby Digital receiver.
Instead, connect to the "DIGITAL" or "COAXIAL"
input of a Dolby Digital/DTS receiver or Processor.
The input of the AV receiver is not compatible with
the PCM/BITSTREAM jack and is primarily for
Laserdiscs only.
(2) Connect the PCM/BITSTREAM jack of unit to the
"DIGITAL" or "COAXIAL" input of a DTS receiver or
Processor.
(3) Refer to the ma n u a l o f t h e c o n n e c t e d
Equipment.
(4) Adjus t t h e volume of your receiver to a
comfortable listening level to avoid any speaker
damage.
10
COAXIAL
To PCM/BITSTREAM
Coaxial cable
(Optional)
To digital
audio input
Connection
Example
Amplifier equipped
with digital audio input
Front
speaker
(left)
Front
speaker
(right)
COAXIAL
To PCM/BITSTREAM
(Optional)
Instruction ManualManual
FUNCTIONS & FEATURES
Turn On/Off
1. Turn On
Plug in the power cord, and the TV should enter into Standby mode. Pressing STANDBY key will turn on
the TV and its power indicator light.
2. Standby
While the TV is on, press the STANDBY key will put the TV in Standby mode. The power indicator light on
the TV set will turn off.
Basic Functions
Changing the Channel
While in Tuner mode, press the CH+/- keys to change the channel, or use the numeric keypad to enter a
new channel.
Adjusting the Volume
To adjust the volume, press the VOL+/ - keys.
Muting the Volume
To mute the volume, press the MUTE key. To restore the volume, press MUTE again or press the VOL + key.
Function Selection Menus
To change the setting of any function, press the TV/VCR MENU key to bring up the main menu. Press
to highlight the desire sub-menu and press < / > (or ENTER) to access. While in the sub-menu, press
to select the item and < / > to adjust the setting. Press the TV/VCR MENU key to return to the main menu
and exit.
While in the setup menu, CH-/+ and VOL-/+ key on the front panel will function as the
/ / < / > on the
remote control.
Picture Menu
Features
This menu allows you to adjust the various picture settings.
-31 (more purplish) to +31 (more greenish)
Tint:
Brightness:
0 (dimmest) to 63 (brightest)
Contrast:
0 (minimum contrast) to 63 (maximum contrast)
0 (minimum color) to 63 (maximum color)
Color:
Sharpness:
0 (minimum sharpness) to 63 (maximum sharpness)
Note:
To control picture artifacts reduce the sharpness setting when
viewing DVD discs.
Picture
Tint
Brightness
Contrast
Color
Sharpness
00
32
32
32
32
Sound Menu
Features
This menu allows you to adjust the various sound settings.
Bass:
Treble:
Balance:
Surround:
AVC:
MTS:
0 (less Bass) to 63 (more Bass)
0 (less Treble) to 63 (more Treble)
L31 (Left Dominance) to R31 (Right Dominance)
Off, On
Off, On
Please refer to the description of MTS/SAP key (P14)
11
Sound
Bass
Treble
Balance
Surround
AVC
MTS
32
32
00
On
Off
Mono
Instruction Manual
FUNCTIONS & FEATURES (continued)
Tuner Menu
Note: This menu is only accessible while the TV is in Tuner mode.
Channel: This feature allows you to change the channel displaying on
screen. Press < / > or the numeric keypad to change the channel.
Add/Erase: This feature allows you to add or remove the channel
currently display on screen to the "active channel list" . Active channel list
is the list of channel that is available by pressing the CH+/- keys. Press
< / > to add or erase.
Antenna: This feature sets the TV tuner to an Air antenna or a Cable
antenna. Please use Air mode when using an over-the-air antenna; use
Cable mode for a cable hookup. Press < / > to select between the two
options.
Tuner
2
Add
Air
Channel
Add/Erase
Antenna
Auto Program
Stop
Start
Auto Program: This feature will setup the Active channel list for the user.
The list will include only the channels with a signal detected. Press > to
begin and < to stop the process.
TV Timer Menu
Clock must be set first in the Clock Set menu.(P23)
Time
This feature allows the TV to display time on the TV screen.
On Time
This feature allows you to preset a time when the TV set will turn
on.
On Channel
This feature allows you to preset the channel on display when the
On Time is activated.
TV Timer
Time
On Time
On Channel
Off Time
Timer
Not Set
--:---:-Once
Clock Must Be Set First.
Off Time
This feature allows you to preset a time when the TV set will turn
off.
Timer:Timer can be set to Once or Always.
General Menu
Language
This feature allows you to pick a language used for the on screen display
(OSD). Press < / > to select the language of your choice - English
(Eng.), French (Fra.) or Spanish (Esp.).
Blue Back
This feature gives you the option to display a blue background on the TV
screen when there is no signal present. Press < / > to toggle between on
and off.
CCD/Text
Closed caption is a feature that allows your TV set to display, on screen,
the dialogue, narration, and sound effect of a TV program. It also allows
you to display teletext signal. Text and caption will be displayed at either
the top or the bottom of the screen. There are nine different settings for
closed captions . You can set it to one of the 4 Closed Caption settings
(CC1-4), one of the 4 Text settings (T1-4), or set this feature to off
(CCD/Text off).
General
Language
Eng.
Blue Back
CCD/Text
Parental Guide
MPAA - X
Notes: A Closed Caption signal may not be displayed under the following conditions:
-When there is no Closed Caption/Text signal to decode
-When the signal is weak or altered (due to interference or poor reception)
-When viewing a dubbed video tape
12
Fra. Esp.
On
Off
On
TV - MA
Instruction ManualManual
FUNCTIONS & FEATURES (continued)
General Menu (continued)
Parental Guide
This feature allows parents to block certain programs from being
viewed, based on the program’s rating. In order to access this
menu, you must first enter a pass code. The factory default is 6688.
Enter the pass code while the Parental Guide is highlighted. Now,
with Parental Guide set as On, press > to access the TV Rating
grid.
TV Rating
Press
to navigate between the ratings, press the TV/VCR
MENU key to block out a particular rating completely. Or, if you
wish, press to highlight an individual rating (anywhere a U is
displayed in the middle of the grid.) Pressing the TV/VCR MENU
key with one of these individual ratings highlighted will block only
programs that feature that particular aspect. See the TV rating
diagram at right for an example. TV ratings are defined in the
charts below:
Age
Defined as
Contents
TV - Y
All Children
FV
Fantasy Violence
TV - Y7
Directed to Older Children (over 7)
D
Sexual Dialogue
TV - G
General Audience
L
Adult Language
TV - PG
Parental Guidance Suggested
S
Sexual Situations
TV - 14
Parents Strongly Cautioned
V
Violence
TV - MA
Mature Audience Only
Defined as
General
Eng. Fra. Esp.
Language
Blue Back
On
CCD/Text
Off
Parental Guide On
MPAA-X
TV-MA
Enter Pass Code - - - -
TV-Rating
Rating
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
FV D L S
U
U U
U
U
U U U
U
U U U
U
U U
Age Based Rating
MPAA - Rating
MPAA Rating
Press > while in the TV Rating grid to access this grid. Press
to navigate between the MPAA ratings. Pressing the
TV/VCR MENU key with a rating highlighted will block that
particular rating from being shown on this TV. A B will show in red
next to the blocked rating. Please note that blocking a lower
rating (for example, PG) will block all higher ratings (PG-13, R,
NC-17, X.)
Pass Code Menu
This menu allows you to change the access code for the
Parental Guide functions of the TV set. Press the TV/VCR MENU
key when Pass Code Control is highlighted. This will turn on or
off the Pass Code function. With the Pass Code function ON, you
can also change the Pass Code. Press to highlight Pass Code,
then enter the new Pass Code using the numeric keypad.
Movie
G
PG
PG-13
R
NC-17
X
Rating
U
U
U
U
U
U
Age Based Rating
Pass Code Menu
Pass Code Control
Pass Code
6688
Note:
The factory pre-set password is 6688. The initial password
will be replaced when the new one is used. Please contact
the service centre in case you forget the password.
13
Enter Pass Code - - - -
V
U
U
U
Instruction ManualManual
FUNCTIONS & FEATURES (continued)
Useful Remote Control Features
DISPLAY
Pressing this key will display the current information of the TV on the screen. (channel, antenna mode, time,
video, etc.) Pressing it again allows you to display the current information of the VCR. To turn off the display,
press the key repeatedly.
SCAN
Press the SCAN key twice, and the TV will begin to scan through all active channels. To stop the Scan,
pressing any key can interrupt scanning. Please note that Scan will only work in Antenna mode.
PICTURE
Your TV has factory preset picture modes that allow you to optimize your TV viewing. To activate these picture
modes, press this key, and you can choose among User, Normal, Movie and Sports.
SOUND
Press this key repeatedly, and you can choose among User, Normal, Speech, Movie and Music.
RECALL
This key will allow you to return to the last channel you viewed. Pressing it again will return you to the channel
you just left.
CC
Pressing the CC key will activate the currently selected Closed Caption or Text under the System Menu.
Pressing it again will turn off the Closed Caption or Text.
VIDEO
This key allows you to toggle between antenna and different video modes.
0-9
Press the 0-9 keys to enter channel numbers directly (2-69 in the Air mode or 1-125 in the Cable mode).
Press the corresponding Number key(s) to enter a channel number from high-digit to low-digit.
Enter digits within 3 seconds of each other.
SLEEP
To determine the minutes before the TV turns off, press the SLEEP key repeatedly to switch the TV to one
of the following modes :
-15
30
45
60
90
120
150
180 (Unit: Minute)
The TV will automatically enter the Standby mode when the preset Sleep time is up.
The TV will display a message one minute before the Sleep timer runs out.
MTS/SAP
In the TV mode, the TV can automatically identify MTS stereo
modes such as Mono, Stereo, Stereo/SAP and Mono/SAP.
14
Signal Received Press MTS/SAP key
Mono
Mono
Stereo
Stereo, Mono
Stereo/SAP
Stereo, SAP, Mono
Mono/SAP
Mono, SAP
Instruction ManualManual
DVD FUNCTIONS
Playing Back a Disc
1. How to playback a disc
1) Press DVD to enter the DVD mode.
2) Press OPEN/CLOSE to open the disc tray.
3) Place the disc on the disc tray. Be sure the playback side is face down.
Note:
A disc may be damaged if not correctly placed on the guides in the disc tray.
This may also cause the DVD player to malfunction.
4) Press the PLAY/PAUSE key. After closing the disc tray playback will start.
The menu screen will appear automatically or you may access the menu screen by pressing TITLE.
Notes:
(1) Moving the unit during playback may cause damage to the disc as well as the unit.
(2) To open and close the disc tray, you should only use the OPEN/CLOSE key.
2. About DVD CD
DVD or CD icons will appear depending on the disc being played back.
DVD: DVD video discs
CD: Audio CDs
3. How to start playback from the menu screen
1) Press
/ < / > or the Number keys to select the title.
2) Press the ENTER key. The DVD player will start playback from the title
selected.
Title 1
Title 2
Title 3
Title 4
4. How to pause playback
Press the PLAY/PAUSE key during playback.
Press the PLAY/PAUSE key to resume normal playback.
5. How to remove the disc
Press the OPEN/CLOSE key. Wait until the disc tray is completely open before removing the disc.
After removing the disc, press the OPEN/CLOSE key to close the disc tray.
6. How to stop playback
Press the STOP key once. The DVD player is stopped.
Press the PLAY/PAUSE key to replay.
Press the STOP key twice. The DVD player is stopped completely.
Note:
At the completion of each movie a menu screen may appear. Be aware that the on-screen setup menu
may damage your TV by permanently burning that image onto the screen. To avoid this, press the STOP
key at the completion of each movie. You may also decide to setup the SCREEN SAVER.
7. Advanced playback
The DVD player allows you to playback discs at various speeds.
2x
4x
8x
16x
2x
4x
8x
16x
1)You can play back a disc at 2x, 4x, 8x, or 16x the normal speed.
Press the REV or FWD keys during playback.
The playback speed becomes 2x the normal speed.
The playback speed changes each time you press the REV or FWD key.
REV: Fast reverse
FWD: Fast forward
Press PLAY/PAUSE to resume normal playback.
15
Instruction ManualManual
DVD FUNCTIONS(continued)
Playing Back a Disc (continued)
Note:
The DVD Player may not playback sound during scan reverse or forward playback of DVD video discs.
The DVD Player will play sound during fast forward or fast reverse playback of audio CDs.
The speeds may vary slightly from disc to disc and the 2x, 4x, 8x, and 16x speeds are only approximate speeds.
8. Resuming playback from the same location
This DVD player allows you to stop playback and continue playback later from the same location on the
disc.
1) Press the STOP key.
This will interrupt the playback and the DVD player memorizes the location where you stopped playback.
2) Press the PLAY/PAUSE key.
The DVD player will resume the playback from the location where you stopped playback.
Notes:
(1)The following actions will cancel the RESUME function:
-Unplugging the unit after you stop playback.
-Ejecting the disc.
(2) Depending on the disc, you may experience a difference of location where playback resumes
(3) Some discs do not utilize this feature.
Using the On-Screen Display
THE UNIT ALLOWS YOU TO VIEW THE DISC INFORMATION ON THE TV SCREEN.
Press DISPLAY during playback, you can view the following on the TV:
-Current title, Track number, Total playing time
Current Title
Current Chapter
Title Elapsed
TT 01/12 CH 06/39 00:02:20
Title Remain
TT 01/12 CH 06/39 00:18:50
Chapter Elapsed
TT 01/12 CH 06/39 00:03:50
Total Title
Total Chapter
Display Off
Chapter Remain
TT 01/12 CH 06/39 00:10:40
To turn off the on-screen display, press DISPLAY repeatedly.
16
Instruction ManualManual
DVD FUNCTIONS(continued)
Locating a Specific Title, Chapter or Track
THE DVD VIDEO DISCS ARE NORMALLY DIVIDED INTO TITLES. THE TITLES ARE SUB-DIVIDED
INTO CHAPTERS. AUDIO CD AND MP3 DISCS ARE DIVIDED INTO TRACKS. YOU CAN
CONVENIENTLY LOCATE ANY SPECIFIC TITLE, CHAPTER, OR TRACK WITH THIS UNIT.
Chapter1 Chapter2
Chapter3
Chapter4 Chapter5
Track1 Track2 Track3
TITLE 1
Track4
Track5
TITLE 2
Audio CD
DVD Video Disc
1. Locating a title using the title menu
You can locate a specific title using the title menu function, if a DVD video disc contains a title menu.
1) Press the TITLE key. On the TV screen, the title menu will appear.
2) Press the
/ < / > keys to select the title you want.
You can also directly locate a specific title by pressing its assigned number with the Number keys.
3) Press the ENTER key. This will cause the unit to start playback from chapter 1 of the title selected.
Notes:
(1) You may find that some discs will not respond to this function.
(2) If different instructions appear on the TV screen, follow those instructions. The instructions above
describe the basic playback procedure. Procedures may vary depending on the contents of
the DVD video disc.
2. Locating a specific chapter or track
This unit allows you to locate consecutive chapters or tracks.
Press the PREV or NEXT key repeatedly to display the requested chapter or track.
The DVD player starts playback from the selected chapter or track.
How to locate proceeding chapters or tracks
• When you press the PREV key, the DVD player starts playback from the beginning of the proceeding
chapter or track.
How to locate succeeding chapters or tracks
• When you press the NEXT key, the DVD player starts playback from the beginning of the succeeding
chapter or track.
Note:On some discs the titles may not display the sub-divided chapters.
Playing Repeatedly
THIS UNIT ALLOWS YOU TO PLAYBACK A SPECIFIC TITLE, CHAPTER, TRACK, OR SEGMENT
REPEATEDLY. (TITLE REPEAT, CHAPTER/TRACK REPEAT, A-B REPEAT).
How to repeat a title, chapter or track
Select the title, chapter, or track you want to repeat.
Press the REPEAT key. The repeat mode changes each
time you press the REPEAT key.
Chapter
Repeats the same chapter.
Title
Repeats the same title.
All
Repeats the disc.
No repeats.
How to repeat a specific segment
1. Press the A-B key at the beginning of the segment in which you
A
want to repeat playback. (point A)
2. Press the A-B key again at the end of the segment (point B).
AB
The Combo Player will automatically return to point A and start to
repeat playback of the selected segment (A-B).
3. Press the A-B key to cancel the A-B repeat function.
The Combo Player will resume to normal playback.
• Depending on the disc, you may experience a difference between point A and the location where playback
actually resumes.
• Be aware that some discs will not respond to the A-B repeat function.
17
Instruction ManualManual
DVD FUNCTIONS(continued)
Selecting Subtitles
THIS UNIT ALLOWS YOU TO DISPLAY SUBTITLES INCLUDED ON THE
DISC ON YOUR TV SCREEN.
How to display subtitles
You have the option to select a preferred subtitle from those included on the
DVD video disc.
Press the SUB-T during playback until the subtitles disappears.
Notes:
• With some DVD's, you may not be able to turn off the subtitles and they will
appear on screen automatically.
• If the subtitles continue to show on your TV even after the DVD has been
turned off, please refer to the TV's close caption settings.
• As you press the SUB-T, the subtitles may not appear immediately during
some scenes.
Subtitle
01/02: English
Subtitle
02/02: French
Subtitle Off
Selecting the Camera Angles/Language/Audio Settings
THIS UNIT ALLOWS YOU TO SELECT FROM SEVERAL DIFFERENT ANGLES AND LANGUAGES.
ANGLE 1
ANGLE 2
Good evening
Bonsoir
Buenas tardes
Selecting the camera angle
Selecting a language
1. How to change the camera angle
Press the ANGLE key while playing back a scene recorded with
1/2
multiple angles.
2/2
Each time you press the ANGLE key, the angle will change.
Notes:
(1) The angle function will not work on DVD video discs that do not
contain recorded multiple angles.
(2) The angle icon indicator will illuminate while playing back a title that contains at least one scene
recorded from multiple angles.
2. How to select a playback audio setting
This DVD player allows you to select a preferred language and sound recording system from those included
on the DVD video disc.
1) Press the AUDIO key during playback.
2) Press the AUDIO key again to cycle backwards.
Audio
1/3 : AC3 5.1CH
English
Language
Total Audio Channels
Current Audio Position
Audio
2/3 : AC3 5.1CH
French
Audio
3/3 : AC3 5.1CH
Spanish
Audio
1/3 : AC3 5.1CH
English
Note:
The DVD player returns to the initial default settings when you turn on the DVD player or replace a disc.
18
Instruction ManualManual
DVD FUNCTIONS(continued)
Playing Back Your Kodak Picture CD
1. Normal
When a Kodak Picture CD is inserted, an automated slide show is launched, each picture in the current
directory will be displayed consecutively in a slide-show fashion and will be scaled to fit most of the TV
screen. Fifteen slideshow transition modes are provided.
To display an image indefinitively, press the PLAY/PAUSE key. To view the Next or Previous picture,
press the NEXT or PREV key. To resume the slideshow press the PLAY/PAUSE key.
2. Image rotation
There are four modes to transformation: "Invert", "Mirror", "Left", and "Right". The arrow keys are used to
select the different transformation modes:
UP
- lnvert/Normal
Down - Mirror/Normal
Right > - Turn right
Left < - Turn left
3. Menu
The D.MENU key is used to display thumbnail pictures. After it is enabled, up to twelve scaled-down
thumbnails pictures will be displayed on the screen. The NEXT and PREV keys can be used to display
the NEXT and PREVIOUS twelve pictures in the current directory.
Note: You can use the
/ < / > / ENTER to select.
MP3 Operation
1. Insert a MP3 CD, the DVD player will initialize the disc when the
tray is closed and the directory (folder) will be shown in the MENU on
screen.
2. Press < / > then the
(song).
key to select and highlight a MP3 file
3. Press ENTER to play the file.
19
Instruction ManualManual
DVD FUNCTIONS(continued)
Setting the Parental Lock
YOU CAN USE THE PARENTAL LOCK FUNCTION ONLY WITH DVD VIDEO DISCS EQUIPPED WITH
THE PARENTAL LOCK FEATURE.
Setting the parental lock
DVD video discs equipped with the parental lock function are rated according to their content. The contents
allowed by a parental lock level and the way a DVD video disc can be controlled may vary from disc to
disc. For example, if the disc allows, you can edit out violent scenes unsuitable for children and replace
them with more suitable scenes, or lock out playback of the disc all together.
1. Press STOP twice during playback.
2. Press DVD SET UP. The SETUP MENU appears on the TV
screen.
3. Select Preference page, press ENTER.
4. Select Parental, press direction keys.
Select Parental, press ENTER.
5. Enter your password then press ENTER key.
The preset password is 1225.
To change your password:
1) Follow step 3 to select password change.
2) Enter old password.
3) Enter new password.
4) Re-enter to confirm your new password.
5) Press ENTER.
6) Press DVD SET UP.
20
Instruction ManualManual
DVD FUNCTIONS(continued)
Customizing the Function Settings
THIS UNIT ALLOWS YOU TO CUSTOMIZE THE PERFORMANCE TO YOUR PERSONAL PREFERENCES.
Displaying the setup menu screen
The SETUP MENU screen asks you to select a setting category from General Setup, Speaker Setup,
Audio Setup, and Preferences. The selected category will provide you the setting details on-screen.
1. Press DVD SET UP.
2. Press
/ < / > to select category (highlight), then press ENTER.
3. Press DVD SET UP to normal playback.
--General Setup Page-TV Display
PS
Angle Mark
On
OSD Lang
ENG
SPDIF Output RAW
Captions
Off
Screen Saver
On
--Speaker Setup Page-Downmix
--Video Setup
Sharpness
Brightness
Contrast
--Dolby Digital Setup-Dual Mono
Dynamic
LT/RT
Stereo*
Page-Low
00
00
Stereo*
L-Mono
R-Mono
Mix-Mono
On*
Off
High
Medium
Low*
* FULL
On
Off*
3/4
1/2
1/4
SPDIF Off
SPDIF/RAW*
SPDIF/PCM
English*
French
Spanish
OFF
-16
-20
0
0
On*
Off
Normal /PS*
Normal /LB
Wide
+16
+20
--Preference Page-Audio
ENG
Subtitle
Off
Disc Menu
ENG
Parental
Password
Default
English*
French
Spanish
Chinese
Japanese
Korean
Russian
Thai
English*
French
Spanish
Chinese
Japanese
Korean
Russian
Thai
Old Password
New Password
Confirm PWD
OK
Reset
English
French
Spanish
Chinese
Japanese
Korean
Russian
Thai
Off*
1 KID SAFE
2G
3 PG
4 PG-13
5 PG R
6R
7 NC-17
8 ADULT*
Off
Change
Notes:
• Preset password is 1225.
• Highlighted function will be expanded at bottom of the screen.
• The SETUP MENU screen disappears if you press the DVD SET UP key while it is displayed.
• Functions and menu may change without notice.
• You must press STOP twice to set up Preferences.
21
Instruction ManualManual
VCR FUNCTIONS
VCR Playback
1. Insert the desired tape.
(In the DVD mode, you must first press the TV/VCR key to change
to TV mode.)
2. If you want to playback it, press PLAY/PAUSE key.
When the playback picture is partially noisy, adjust with
TRK-/+ key.
3. To stop it, press STOP key.
For still, press PLAY/PAUSE key in playback mode.
4. To playback forward fast or to reverse it, press FWD or REV key respectively.
Press STOP/EJECT key on the front panel or EJECT key on the remote control to remove the tape.
Recording
•To record with VCR
Insert a tape for recording. The tape must have a recording tab.
With CH+/- and Number keys, select the desired boradcasting channel or external input unit to record.
Select the desired speed (SP or SLP) with SPEED key. Press REC key.
Press • PAUSE key to pause recording, press again to resume.
If the pause status continues for five minutes, the recording will be cancelled automatically.
To stop recording, press STOP key.
•To play a DVD during VCR recording
If you want to playback a DVD during VCR recording, insert a DVD disc.
When the desired DVD disc is loaded, press the DVD key to switch to DVD mode and press the
PLAY/PAUSE key to watch the DVD.
•To record from DVD to videotape
Press DVD key to switch output to DVD mode. Insert the desired DVD disc. (You cannot record a DVD disc
which is copy protected.)
Insert a tape for recording. Press REC key. To stop record, press STOP key. If you do not press stop,
the DVD plays on and video continues to record.
This product incorporates copyright protection technology that is protected by method claims of certain U.S
patents and other intellectual property rights owned by Macrovision Corporation and other right owners Use
of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
•One touch timer recording (OTR)
One-Touch Recording (OTR) allows you to record in 30-minute increments up to 4 hours at the touch of a
key.
Start recording: Following the instrctions on "Recording".
Activate OTR: While in Record mode, press the OTR key again to activate One-Touch Recording (OTR).
Add recording time:
Press the OTR key to add recording time in 30 minute increments up to 4 hours.
The unit stops recording automatically when the time has elapsed.
22
Instruction ManualManual
VCR FUNCTIONS(continued)
Search Function
Go to Zero Search
As soon as the counter searches 0:00:00 , the tape will play
SEARCH
automatically.
Counter Search
Go to Zero Search
Counter Search
With
or Number key, enter the desired time and press ENTER.
The counter appears on screen. When the counter searches the set
Index Search (+)
number, the tape will play automatically. If not, "Start of tape" or "End
Index Search (-)
of tape" will appear on the TV screen.
Index Number Search
Index search (+) / Index search (-)
To search in the forward direction, highlight Index Search(+) Index
Move:
Select: ENTER
searching motion, then press ENTER.
Too search in the reverse direction, highlight Index Search(-) Index
searching motion, then press ENTER.
• The index signal is recorded on the tape automatically when the
recording is started. You can view a recording at a specific start point.
Index Number Search
• To search in the forward direction, press up key to select desired Index Number.
Too search in the reverse direction, press down key to select desired Index Number.
After setting up, please press ENTER.
Quit: MENU
CLOCK SET
VCR Setting
Clock Set
Set the current date and time with
/ < / > or Number keys.
For Date set, follow the order of month/day/year;
for TIME set, follow the order of hour/minute in CLOCK SET menu.
Press TV/VCR MENU after completed.
VCR Timer
1.Channel
Move into desired channel signal with left/right key.
Cable
Video1(S)
Video2
Antenna
Date
Time
10/08/2003(Wed) 10:35 AM
(mm/dd/yy)
Move:
Input:
Quit: MENU
PROGRAM 1 (10/08 WED)
2. Start Date
Select the desired date to record with left/right or Number key.
3. REC Cycle
One Time
Weekly
Weekdays
Daily
Channel
Start Date
Cable 01
REC Cycle
One Time
Start Time
10 : 00 AM
End Time
11 : 00 AM
Tape Speed
SP
Move:
Input:
4. Start Time/End Time
Select the desired time to record with left/right or Number key.
5. Tape speed
SLP=1/3 SP
Press TV/VCR MENU to exit after completed.
Repeating the above steps you can program up to 8-events.
After programming the timed recordings, press the CLEAR key to exit the program.
23
10 / 08 (Wed)
Quit: MENU
Instruction ManualManual
VCR FUNCTIONS(continued)
Other Remote Control Features
A-B
During tape playback, press the key once. The player will memorize the beginning of a segment (point A)
and continue to play. Press it again. The combo will memorize the end of a segment (point B). At the same
time, it will return to point A and start to repeat playback of the selected segment (A-B). After repeating
playback of the segment five times, the player will resume to normal playback from point B.
SKIP
Each time you press the key during tape playback, the tape skips forward by 30 seconds, and then returns
to normal playback.
PAUSE/STEP
During recording (except timer recording), pressing the key pauses recording until you press it again. The
player continues to record at the location where the taped is paused.
During tape playback, the key does not function. During still playback, pressing the key will make pictures
advance frame by frame. The still function will be released if there is no operation for 5 minutes. The VCR
will change to the STOP mode.
F.ADV (Frame advance): Each time you press the key during still playback, the picture advances one
frame. Press the PLAY/PAUSE key to resume normal playback.
Tape Handling
1. Do not use damaged or defective tapes. Faulty tapes may cause damage to the VCR play heads and
mechanism. Do not use video tapes with the following conditions.
-Tapes with mold
-Tapes stained with liquids, debris or other substances
-Tapes with crinkles, snags or breaks
-Disassembled tapes
2. Moisture condensation may occur in tape. Moisture condensation damages the tape.
Please use the tape after the moisture condensation has disappeared.
3. After use, store tape vertically in a case to prevent loose.
4. Do not store tapes in places with the following conditions:
-High temperature and humidity
-Areas subject generation of mold
-Areas in direct sunlight
-Areas subject to dust and dirt
-Near strong magnetic materials such as speakers
24
Instruction ManualManual
TROUBLESHOOTING GUIDE
Check the following guide for a possible correction to a problem before contacting customer support.
Symptoms
No power
Dark, Poor or No picture
No sound
No TV signal
Stripe or purple interference
appears in the screen
Picture becomes snowy.
Picture with multi -image
TV channel not received
Black box appears on screen.
Remote control doesn’t operate.
Brightness is unstable or noises are
produced on playback pictures
The DVD video player
doesn’t start playback
MP3 won’t read disc
or it skips
Timer recording failure
Cannot go into Record mode.
Playback picture is partially noisy
Cannot view a tape but the audio is
OK
Video or color fades in and out when
making a copy of a video tape.
Cannot remove the tape
Correction
• Connect the power plug into the wall outlet securely.
• Verify the connection from the VCR video output to the TV video input is secure. Then switch
TV to the appropriate Video mode by pressing TV/V IDEO button.
• Adjust picture setting for tint, color brightness and sharpness.
• Verify coaxial cable from antenna is connected to RF IN.
• Connect the audio cables into the terminals securely.
• Verify the connection from the VCR audio outpu t to the TV audio input. Then switch to the
appropriate mode on the receiver. Refer to your audio amplifier owner’s manual.
• Verify the volume is at an appropriate level
• The mute feature may be enabled, press MUTE button to verify.
• Check whether AMP your receiver is set to the TV mode (if connected).
• Check whether the antenna is well connected to the TV receiver.
• Unplug the TV from the wall for 30 seconds, then plug in and try again.
• Unplug the antenna connection from the back of the TV, unplug the TV from the wall.
Wait for 30 seconds, then power on again.
• Interference may come from high frequency sources such as a broadcasting station, poor
ground connection in cable used, or non shielded audio speakers too close to the picture tube.
• Verify the antenna lead wire is in working condition .
• Verify the antenna is connected securely to the RF in jack .
• Change the direction o f antenna to minimize the multi image.
• The video frequency radiated from TV station can be reflected by tall buildings, high tower, etc.
• Make sure the Air/Cable setting is correct.
• Channel may be locked with block channel fe ature, such as Parental Control. Refer to manual.
• Check Add/Erase feature, as channel may be have been erased during set up. Refer to manual.
• Closed Caption to Text feature may be active.
• Batteries may be weak. Replace batteries.
• Check the batteries are installed with the correct +/ - polarity.
• Make sure remote sensor is not blocked by anything, including deflection from a glass cabinet.
• What you’re viewing may be effect of the copy protection circuitry required on all DVD players.
• Do not connect and monitor through another VCR.
• Try another disc.
• Place the disc with the graphics side up and clear side down.
• Place the disc on the disc tray correctly inside the guide.
• Make sure the disc is free from scratches & fingerprints.
• Press the SETUP button to turn off the menu screen.
• Cancel the parental lock function o r change the parental lock level. (Preset password: 1225.)
• Turn the power off then disconnect the power plug for 30 seconds and reinsert it back into the
wall. Power on again.
• Use region 1 disc only.
• Reburn disc a s the software edition used may not be compatible with the player. Check
software maker’s web site for instructions.
• Use new editions of software such as Voyetra Audiostation 4, Adaptec’s “Easy CD Creator” or
NT 1. Roxio’s Toast Titanium, etc.
• Make sure MP3 file are not encoded with a variable bit rate such as provided by Real
Networks.
• Make sure the timer recording is set correctly.
• Make sure power is off. To activate timer and verify you indicated proper AM/PM mode.
• Make sure the clock is set correctly.
• Make sure the tape has a safety tab. If needed, cover the hole with adhesive tape.
• Adjust tracking control for a better picture by pressing the TRK+/- key.
• Head cleaning may be necessary.
• This could be the result of copy guard protection. You cannot copy a copyrighted video tape.
• Check if the player is in the TV/VCR mode. If not, press the TV/VCR key to switch the mode.
25
English
For service, support and warranty information, visit
www.polaroidelectronics.com or in the US call 1-866-2895168, in Canada call 1-866-301-7922 and in Mexico call
01-800-400-2443.
"Polaroid" is a registered trademark of Polaroid Corporation
of Waltham, MA USA and licensed for use on the TBX2000AF to Petters Consumer Brands, LLC.
French
Pour les informations concernant l'entretien, l'assistance et
la garantie, visiter www.polaroidelectronics.com ou appeler
le 1-866-289-5168 aux États-Unis et le 1-866-301-7922 au
Canada. Au Mexique appeler le 01-800-400-2443.
"Polaroid" est une marque déposée de Polaroid
Corporation, Waltham, MA, États-Unis, et dont l'usage est
autorisé pour le TBX-2000AF auprès de Petters Consumer
Brands, LLC.
Spanish
Para información relacionada al mantenimiento, soporte y
garantía, visite www.polaroidelectronics.com o, en los
Estados Unidos, llame al 1-866-289-5168. En Canadá,
llame al 1-866-301-7922. En México llame al
01-800-400-2443.
"Polaroid" es una marca registrada de Polaroid Corporation,
Waltham, MA, USA. Petters Consumer Brands, LLC, ha
sido autorizado para usarla en el TBX-2000AF.
Download PDF

advertising