Canon HF M41 Camcorder User Manual

Instructions for use
WASHING MACHINE
Contents
GB
English
GB
Installation, 2-3
Unpacking and levelling, 2
Electric and water connections, 2-3
The first wash cycle, 3
Technical details, 3
Washing machine description, 4-5
Control panel, 4
Display, 5
“MEMO” Programme, 5
Starting and Programmes, 6
Briefly: how to start a programme, 6
Programme table, 6
WIXE 127
Personalisations, 7
Setting the spin cycle, 7
Setting the Delay Timer, 7
Setting the temperature, 7
Functions, 7
Detergents and laundry, 8
Detergent dispenser, 8
Bleach cycle, 8
Preparing your laundry, 8
Special items, 8
Precautions and advice, 9
General safety, 9
Disposal, 9
Saving energy and respecting the environment, 9
Care and maintenance, 10
Cutting off the water or electricity supply, 10
Cleaning your appliance, 10
Cleaning the detergent dispenser, 10
Caring for your appliance door and drum, 10
Cleaning the pump, 10
Checking the water inlet hose, 10
Troubleshooting, 11
Service, 12
Before calling for Assistance, 12
1
Installation
GB
Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the washing machine to inform
the new owner as to its operation and features.
Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking and levelling
Unpacking
Electric and water connections
1. Unpack the washing machine.
2. Check whether the washing machine has been
damaged during transport. If this is the case, do not
install it and contact your retailer.
Connecting the water inlet hose
3. Remove the three
protective screws and
the rubber washer with
the respective spacer,
situated on the rear of
the appliance (see
figure).
4. Seal the gaps using the plastic plugs provided.
5. Use the plug provided to seal the three holes
where the plug was housed, situated on the lower
right-hand side on the rear of your appliance.
6. Keep all the parts: you will need them again if the
washing machine needs to be moved to another
location.
Packaging materials are not children's toys.
Levelling
Your machine may make a considerable amount of
noise if the two front feet have not been adjusted
correctly.
1. Install the washing
machine on a flat sturdy
floor, without resting it
up against walls,
furniture cabinets or
other.
2. If the floor is not
perfectly level, compensate for any unevenness
by tightening or
loosening the adjustable
2
front feet (see figure); the angle of inclination,
measured according to the worktop, must not
exceed 2°.
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the washing
machine.
1. Connect the supply
pipe to the water mains
using a gas 3/4
attachment, fitting the
rubber gasket and the
filter supplied with the
appliance and ensuring
that they are fimly
tightened to the taps.
The water supply marked
C must be connected to the cold water tap; the pipe
marked H must be connected to the hot water tap.
Both pipes may be connected to the cold water tap
using the special Y connection with multiple
attachments, supplied with the appliance (see figure).
Before making the connection, allow the water to run
freely until it is perfectly clear.
2. Connect the other end
of the water inlet hose to
the washing machine,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the
rear of the appliance
(see figure).
3. Make sure there are no kinks or bends in the
hose.
The water pressure at the tap must be within the
values indicated in the Technical details table
(on the next page).
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Connecting the drain hose
The power supply cable must never be bent or
dangerously compressed.
The power supply cable must only be replaced by
an authorised serviceman.
• the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
When the washing machine is installed, the mains
socket must be within easy reach.
59.5 cm w ide
85 cm h igh
56.5 cm deep
Capacity
from 1 to 6 kg
Electric
connections
voltage 230/240 Volts 50 Hz
maximu m absorbed pow er 1850 W
Water
connections
maximu m press u re 1 MPa (10 bar)
min imu m press u re 0.05 MPa (0.5 bar)
dru m capacity 52 litres
Spin speed
u p to 1200 rpm
Control
programm es
according to
IEC456 directive
programme 2; temperatu re 60°C;
ru n w ith a load of 6 kg.
Th is applian ce is complian t w ith th e
follow in g Eu ropean Commu n ity
Directives :
- 73/23/CEE of 19/02/73 (L ow
Voltage) an d s u bsequ en t amen dmen ts
- 89/336/CEE of 03/05/89
(Electromagn etic Compatibility) an d
su bsequ en t amen dmen ts
- 2002/96/CE
Service
The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
Dimensions
Troubleshooting
• the supply voltage is included within the values i
ndicated on the Technical details table
(on the right);
W IXE 127
Care
• the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (on the right);
Model
Precautions
Before plugging the appliance into the mains
socket, make sure that:
• the socket is earthed and in compliance with the
applicable law;
Technical details
Detergents
Electric connection
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
Programmes
We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
The first wash cycle
Description
Warning! The company denies all liability if and when
these norms are not respected.
alternatively, place it
over the edge of a
basin, sink or tub,
fastening the duct
supplied to the tap (see
figure). The free end of
the hose should not be
underwater.
GB
Do not use extensions or multiple sockets.
Installation
65 - 100 cm
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from
the floor;
3
Washing machine description
Control panel
FUNCTION
GB
Buttons
START/RESET
button
START/STOP
button
Display
Detergent dispenser
Control knob
TEMPERATURE
button
SPIN
button
Detergent dispenser to add detergent and fabric
softener (see page 8).
SPIN button to adjust the spin speed or exclude it
altogether (see page 7).
DELAY TIMER button to delay the start of the set
programme for a maximum period of 24 hours
(see page 7).
TEMPERATURE button to adjust the wash temperature (see page 7).
Display to programme the washing machine and
follow the wash cycle progress (see opposite page).
4
DELAY TIMER
button
FUNCTION buttons: to select the functions
available. The button corresponding to the function
selected will remain on.
START/RESET button to start the programmes or
cancel any incorrect settings.
START/STOP button to turn the washing machine
on and off.
Control knob to select the wash programmes.
The knob stays still during the cycle.
Display
GB
Description
Once you have pressed the START/RESET button to
start the programme, the display will indicate the
amount of time left until the end of the wash cycle. If
a delayed start has been set (using the Delay Timer,
see page 7), the delay time will be indicated on the
display.
Installation
In addition to being a practical tool to programme your appliance (see page 7), the display provides useful
information concerning the wash cycle.
Programmes
At the end of the programme, the word END is displayed.
Detergents
Door lock:
If the symbol is on, the washing machine door is locked to prevent it from being opened accidentally. To avoid
any damages, wait for the symbol to switch itself off before you open the appliance door.
In the event of an anomaly, an error code will appear, such as: F-01, see page 11 “Toubleshooting”.
Precautions
Care
Service
This programme allows you to store your favourite or most-used wash cycle.
All you have to do is set the desired programme and, once it has started, turn the KNOB to position
; the
wash cycle will be stored automatically and the word MEMO appears on the display, flashing for a few seconds.
Subsequently, you can start the "MEMO" cycle by simply turning the KNOB to position
; you will be able to see
the temperature/spin cycle/delay timer values by pressing the corresponding buttons; you will also be able to
modify them but this variation will only be valid for the programme in progress and it will not be stored in the
"MEMO" cycle.
If you want to store a new wash cycle, repeat the above-mentioned operations.
Troubleshooting
"MEMO" Programme
5
Starting and Programmes
Briefly: starting a programme
GB
5. Add the detergent and any fabric softener
(see page 8).
6. Start he programme by pressing the START/RESET
button.
To cancel it, keep the START/RESET button
pressed for at least 2 seconds.
7. When the programme has ended, the word END is
displayed. Take out your laundry and leave the
appliance door ajar to allow the drum to dry
thoroughly.
8. Turn the washing machine off by pressing button .
1. Turn the washing machine on by pressing button
.
2. Load your laundry into the washing machine and
shut the appliance door.
3. Set the knob to the desired programme. The
estimated duration of the selected programme is
displayed. The temperature and spin speed are
automatically set according to the programme
(to change them, see page 7).
4. Select any functions (see page 7).
Programme table
Typ e of fa b ric a nd
d e gre e of soil
P rogra m m e s
Te m p e ra ture
D e terge nt
Fab ric
softener
prew as h
w as h
•
•
•
C ycle
Sta in re m ova l
length
op tion/b le a c h
(m inutes)
D e scrip tion of w ash c yc le
S tandard
C otton: Extremely soiled w hites
Pre-wash, wash cycle, rinse cycles,
intermediate and final spin cycles
Wash cycle, rinse cycles,
intermediate and final spin cycles
Wash cycle, rinse cycles,
intermediate and final spin cycles
Wash cycle, rinse cycles,
intermediate and final spin cycles
1
90 °C
2
90 °C
•
•
2
60 °C
•
•
2
40 °C
•
•
3
40 °C
•
•
D elicate/
Tradition al
70
4
60 °C
•
•
D elicate
75
4
40 °C
•
•
D elicate
60
Wo o l
5
40 °C
•
•
50
Very d elicate fab rics
6
3 0 °C
•
•
45
7
60 °C
•
•
60
Wash cycle, rinse cycles,
intermediate and final spin cycles
8
40 °C
•
•
50
Wash cycle, rinse cycles,
intermediate and final spin cycles
9
40 °C
•
•
40
W ash cycle, rinse cycles,
delicate spin cycle
10
3 0 °C
•
•
30
W as h cycle, rin s e cycles an d
delicate s pin cycle
Sports shoes (MAX. 2 pairs)
11
30 °C
•
•
50
Cold w ash (w ithout detergents),
w ash cycle, rinse cycles, and
delicate spin cycle
Fabrics for sportsw ear
(Tracksuits, shorts, etc.)
12
3 0 °C
•
•
60
Wash cycle, rinse cycles,
intermediate and final spin cycles
(sheets, tablecloth s, etc.)
C otton: Extremely soiled w hites
(sheets, tablecloth s, etc.)
C otton: Heavily soiled w h ites
and fast colours
C otton: Heavily soiled w h ites
and delicate colours
C otton: Sligh tly soiled w h ites
an d delicate colou rs (sh irts ,
jum pers, etc.)
Synthetics: Heavily soiled fast
colours (baby linen, etc.)
Synthetics: Heavily soiled fast
colours (baby linen, etc.)
(cu rtain s , s ilk, vis co s e, etc.)
135
D elicate/
Tradition al
D elicate/
Tradition al
D elicate/
Tradition al
125
110
105
Wash cycle, rinse cycles,
intermediate and final spin cycles
W ash cycle, rinse
crease or delicate
W ash cycle, rinse
crease or delicate
cycles, antispin cycle
cycles, antispin cycle
W as h cycle, rin s e cycles , an ticrease an d delicate s pin cycle
W as h cycle, rin s e cycles , an ticreas e or drain in g cycle
Tim e 4 y o u
C otton: Heavily soiled w h ites
and fast colours
C otton: Sligh tly soiled w h ites
an d delicate colou rs (sh irts ,
jum pers, etc.)
Synthetics: Delicate colours (all
types of sligh tly soiled
garments)
D elicate colours (all types of
sligh tly soiled garments)
S po rt
M EMO
Allow s fo r an y w as h cycle to be s tored (see page 5).
PA R TIA L P R O G R A M M E S
R in s e
•
D elicate/
Tradition al
R in s e cycles an d s p in cycle
Spin
Draining and spin cycle
D rain
D rain in g
Notes
-For programmes 7 and 8, we advise against exceeding a wash load of 3.5 kg.
-For programme 12 we advise against exceeding a wash load of 2 kg.
-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.
Special programme
Daily (programme 10 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts
30 minutes and allows you to save on both time and energy. By setting this programme (10 at 30°C), you can wash
different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
6
Personalisations
Setting the spin cycle
FUNCTION buttons
Programmes
Press the button
and you will see the word OFF on the
display, while the relative symbol flashes.
Press the button again and "1h" appears, that is, a delay of one
hour (this can reach up to 24h); stop on the "desired" delay; after
approximately 2 seconds the setting is accepted, following which,
the time for the set programme appears on the display and the
remains on.
symbol
If you now press the START/RESET button, the set "delay"
appears; this decreases every hour until the start of the cycle. In this phase, the "delay" can only be modified by
decreasing it.
The Delay Timer regulation is enabled with all programmes.
Description
Setting the Delay Timer
GB
Installation
If, when the appliance is switched on, the KNOB is positioned on
a programme with a spin cycle,
a fixed appears. Press button
and the maximum spin speed allowed for the programme set
will be displayed, and the
icon flashes. Press it again and the
values lower until they reach OFF, which indicates that the spin
cycle has been excluded (press it again to go back to the
maximum value); stop on the desired speed, after approximately
2 seconds the setting is accepted: the symbol
remains fixed.
The spin cycle setting is enabled with all the programmes except
for 6 and the Draining cycle.
Setting the temperature
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set.
If you set a function that is incompatible with another function you selected previously, only the last one selected
will be enabled.
Enabled with
programmes:
Stain
removal
Bleaching cycle
designed to
remove the
toughest stains.
Please remember to pour the bleach into extra compartment 4
(see page 8).
This function is incompatible with the EASY IRON function.
2, 3, 4,
Rinse cycle.
Extra Rinse
Increases the
efficiency of the
rinse.
Recommended when the appliance has a full load or with large
quantities of detergent.
1, 2, 3, 4, 7,
8, 9, 11, 12,
Rinse cycle.
When this function is set, programmes 4, 5, 6 will end, with the
laundry left to soak (Anti-crease), and the relative button flashes:
- to conclude the cycle, press the START/RESET button or the
EASY IRON button;
- to run the draining cycle alone, set the knob to the relative
symbol
and press the START/RESET button.
This function is incompatible with the STAIN REMOVAL function.
3, 4, 5, 6, 7, 8,
9, Rinse
cycle.
Easy iron
This option
reduces the
amount of
creasing on
fabrics, making
them easier to
iron.
Service
Comments
Troubleshooting
Effect
Care
Function
Precautions
Functions
Detergents
If, when the appliance is switched on, the KNOB is positioned on a programme for which the temperature needs
to be regulated, a fixed
appears. Press button
and the maximum temperature allowed for the programme
set will be displayed and the
icon flashes. Press it again and the temperature lowers until it reaches OFF, which
indicates a cold wash cycle (press it again to go back to the maximum value); stop on the desired value, after
approximately 2 seconds the setting is accepted: the symbol
remains fixed.
The temperature adjustment is enabled with all wash programmes.
7
Detergents and laundry
GB
Detergent dispenser
Preparing your laundry
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up on the interior of your
appliance and even pollute the environment.
• Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites.
• Empty all pockets and check for loose buttons.
• Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 6 kg
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1,5 kg
4
1
2
3
Open up the detergent
dispenser and pour in
the detergent and fabric
softener, as follows.
How much does your laundry weigh?
compartment 1: Detergent for pre-wash
(powder)
Before pouring in the detergent, make sure that
extra compartment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in
immediately prior to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.
extra compartment 4: Bleach
Do not use hand wash detergent because it may
form too much foam.
Bleach cycle
Traditional bleach should be used on sturdy
white fabrics, and delicate bleach for coloured
fabrics, synthetics and for wool.
Place extra
compartment 4,
provided, into
compartment 1.
When pouring in the
bleach, be careful not to
exceed the "max" level
indicated on the central
pivot (see figure).
To run the bleach cycle alone, pour the bleach into extra
compartment 4, set the Rinse programme
and
enable the Stain removal function (see page 7).
To bleach during a wash cycle, pour in the detergent
and fabric softener, set the desired programme and
enable the Stain removal function (see page 7).
The use of extra compartment 4 excludes the
possibility of using the pre-wash cycle.
8
1
1
1
1
1
sheet 400-500 g
pillow case 150-200 g
tablecloth 400-500 g
bathrobe 900-1,200 g
towel 150-250 g
Special items
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme 6
which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out and
load a maximum of 2-3 kg, repeating the rinse cycle
once or twice and using the delicate spin cycle.
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1,5 kg.
Precautions and advice
• This appliance has been designed for nonprofessional, household use and its functions must
not be changed.
• Disposing of an old washing machine:
before scrapping your appliance, cut the power
supply cable and remove the appliance door.
• This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
Saving energy and respecting the
environment
• Never touch the washing machine when barefoot
or with wet or damp hands or feet.
• Do not open the detergent dispenser while the
appliance is in operation.
• Never force the washing machine door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
• Always keep children well away from the
appliance while in operation.
• The appliance door tends to get quite hot during
the wash cycle.
Disposal
• If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board's peak load.
The Delay Timer option (see page 7) helps to
organise your wash cycles accordingly.
• If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
Service
• Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on
human health and the environment.
• Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
Troubleshooting
• Before loading your laundry into the washing
machine, make sure the drum is empty.
• Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on
energy.
Care
• Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
• The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
Precautions
• In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
Saving on detergent, water,
energy and time
• To avoid wasting resources, the washing machine
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on
energy.
Detergents
• Do not touch the drain water as it could reach
very high temperatures.
Environmentally-friendly technology
If you only see a little water through your appliance
door, this is because thanks to the latest technology,
your washing machine only needs less than half the
amount of water to get the best results: an objective
reached to respect the environment.
Programmes
• Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
GB
Description
General safety
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Installation
The washing machine was designed and built in
compliance with the applicable international safety
regulations. The following information is provided for
your safety and should consequently be read
carefully.
9
Care and maintenance
Cutting off the water or electricity
supply
GB
• Turn off the water tap after every wash. This will
limit the wear of your appliance's water system
and also prevent leaks.
• Unplug your appliance when cleaning it and
during all maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser
by pulling it out (see
figure).
Wash it under running
water; this operation
should be repeated
frequently.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump that does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber that protects the
pump, situated in the lower part of the same.
Make sure the wash cycle has ended and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front of the
washing machine (see
figure);
2. unscrew the lid
rotating it anticlockwise (see figure): a
little water may trickle
out. This is perfectly
normal;
Caring for your appliance door and
drum
• Always leave the appliance door ajar to prevent
unpleasant odours from forming.
3. clean the interior thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during
the wash cycles, water pressure is very strong and
a cracked hose could easily split open.
Never use hoses that have already been used.
10
Troubleshooting
Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem
can't easily be solved by consulting the following list.
Possible causes/Solution:
The washing machine won't
start.
• The appliance is not plugged into the socket, or not enough to
make contact.
• There has been a power failure.
The wash cycle won't start.
• The programme does not foresee the draining: some programmes
require enabling the draining manually (see page 6).
• The Easy iron option is enabled: to complete the programme, press
the START/RESET button (see page 7).
• The drain hose is bent (see page 3).
• The drain duct is clogged.
The machine is blocked and the
display shows an anomaly error
code (i.e. F-01).
• This means there is a problem with the machine. Before calling
Assistance, please follow the set of instructions below:
1. Switch off the machine.
2. Remove the plug connecting the appliance to the mains supply and
wait for at least 40 seconds.
3. Place the plug back into the socket.
4. Switch on the machine.
5. If the problem is still evident after this process has been carried out,
contact Assistance.all for Assistance because this means there is an
abnormality.
There is too much foam.
• The detergent is not suitable for machine washing (it should bear
the definition "for washing machines" or "hand and machine wash",
or the like).
• You used too much detergent.
Service
• The water inlet hose is not screwed on correctly (see page 2).
• The detergent dispenser is obstructed (to clean it, see page 10).
• The drain hose is not secured properly (see page 3).
Troubleshooting
The washing machine leaks.
Care
• When the machine is installed, the locking screws for the oscillating
assembly are still in place. Remove the screws (see page 2).
• The washing machine is not level (see page 2).
• The washing machine is closed in between furniture cabinets and
the wall (see page 2).
Precautions
The washing machine vibrates
too much during the spin cycle.
• The drain hose is not fitted between 65 and 100 cm from the floor
(see page 3).
• The free end of the hose is underwater (see page 3).
• The wall drainage system doesn't have a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and call for Assistance. If the dwelling is on one of
the upper floors of a building, there may be drain trap problems causing the
washing machine to load and unload water continuously. In order to avoid
such an inconvenience, special anti-drain trap valves are available in shops.
Detergents
The washing machine does not
drain or spin.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap is not turned on.
There is a water shortage.
The water pressure is insufficient.
The START/RESET button has not been pressed.
Programmes
The washing machine
continuously loads and unloads
water.
•
•
•
•
•
•
Description
The washing machine fails to
load water (The wording H2O is
displayed).
• The appliance door is not shut properly (the word DOOR is
displayed).
• The
button has not been pressed.
• The START/RESET button has not been pressed.
• The water tap is not turned on.
• A delayed start has been set (using the Delay Timer, see page 7).
Installation
Problem
GB
11
Service
195053270.00
07/2005 - Xerox Business Services
Before calling for Assistance:
• Check whether you can solve the problem on your own (see page 11);
• Restart the programme to check whether the problem has been solved;
• If this is not the case, contact an authorised Technical Service Centre on the telephone number
provided on the guarantee certificate.
GB
.
If the machine has been installed or used incorrectly, you may be charged for the maintenance callout
service
Always request the assistance of authorised servicemen.
Service
Notify the operator of:
• the type of problem;
• the appliance model (Mod.);
• the serial number (S/N).
This information can be found on the data plate situated on the rear of the washing machine.
12