PCI-6871
PCI Eden400 Half-sized SBC
with SODIMM/VGA
LCD/LVDS/LAN and CFC2
Users’ Manual
Copyright
This document is copyrighted, © 2002. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of
the original manufacturer. Information provided in this manual is
intended to be accurate and reliable. However, the original manufacturer
assumes no responsibility for its use, nor for any infringements upon the
rights of third parties that may result from such use.
Acknowledgements
Award is a trademark of Award Software International, Inc.
VIA is a trademark of VIA Technologies, Inc.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business
Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows® is a registered trademark of Microsoft Corp.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
ESS is a trademark of ESS Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
SMI is a trademark of Silicon Motion, Inc.
Creative is a trademark of Creative Technology LTD.
All other product names or trademarks are properties of their respective
owners.
For more information on this and other EMAC products, please visit
our website at:
http://www.emacinc.com
For technical support and service, please visit our support website at:
http://www.emacinc.com/support/
This manual is for the PCI-6871.
Part No. 2006687110
1st Edition, Dec, 2002
PCI-6871 User’s Manual
ii
Packing List
Before you begin installing your card, please make sure that the following
materials have been shipped:
• 1 ea. PCI-6871 all-in-one single board computer
• 1 ea. startup manual
• CD-ROM or disks for utility, drivers, and manual (in PDF format)
• 1 ea. power cable p/n: 1703080101
• 1 ea. PS/2 KB/M cable p/n: 1700060202
• 1 ea. Printer cable p/n:1700260250
• 1 ea. FDD cable p/n:1701340603
• 1 ea. EIDE cable p/n:1701400452
If any of these items are missing or damaged, contact your distributor or
sales representative immediately.
Model No. List
Description
PPCI-6871F-J0A1 PCI Eden400 Half-sized SBC with SODIMM/VGA
LCD/LVDS/LAN and CFC2
Additional Information and Assistance
1. Visit the manufacturer's web site at www.emacinc.com where you can
find the latest information about the product.
2. Contact your distributor, sales representative, or customer
service center for technical support if you need additional assistance.
Please have the following information ready before you call:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version, application
software, etc.)
• A complete description of the problem
• The exact wording of any error messages
iii
PCI-6871 User’s Manual
iv
Table of Contents
Contents
Chapter
1 General Information ........................................1
1.1
1.2
1.3
Introduction ....................................................................... 2
Features ............................................................................. 3
Specifications .................................................................... 3
1.3.1
1.3.2
1.3.3
1.3.4
1.3.5
1.4
Chapter
Standard SBC Functions................................................. 3
VGA/LCD/LVDS Interface............................................ 4
LVDS: Supports 2 Channel LVDS interface................4
PCI bus Ethernet interface .............................................. 4
Mechanical and Environmental ...................................... 4
Board layout: dimensions.................................................. 5
2 Installation ........................................................7
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Jumpers.............................................................................. 8
Connectors......................................................................... 8
Locating jumpers............................................................. 10
Locating Connectors ....................................................... 11
Setting Jumpers ............................................................... 12
Clear CMOS (JP1) .......................................................... 13
Installing system memory (SODIMMs).......................... 14
2.7.1
2.8
2.8.1
2.9
Connecting the hard drive............................................. 16
Solid State Disk............................................................... 16
2.9.1
2.10
Installing SODIMMs .................................................... 14
IDE, CDROM hard drive connector (CN1, CN7)........... 15
CompactFlash (CN28) .................................................. 16
Floppy drive connector (CN6) ........................................ 16
2.10.1 Connecting the floppy drive ......................................... 17
2.11
2.12
2.13
Parallel port connector (CN2) ......................................... 17
Keyboard and PS/2 mouse connector (CN25) ................ 17
Power & HDD LED, Reset (CN13, CN8) ...................... 18
2.13.1 Power & HDD LED (CN13) ........................................ 18
2.13.2 Reset switch (CN8)....................................................... 18
2.14
Power connectors (CN11, FAN1) ................................... 18
2.14.1 Main power connector, +5 V, +12 V (CN11).............. 18
2.14.2 CPU Fan power supply connector (FAN1)................... 18
2.15
ATX power control connector (CN3, CN5).................... 19
2.15.1 ATX feature (CN3) and soft power switch (CN5) ....... 19
2.16
2.17
2.18
IR connector (CN9)......................................................... 20
Audio interfaces (CN10) ................................................. 20
COM port connector (CN19, CN20)............................... 20
2.19
VGA/LCD/LVDS interface connections ........................ 20
2.18.1 COM2 RS-232/422/485 setting (JP3)........................... 20
2.19.1 CRT display connector (CN12) .................................... 21
v
2.19.2
2.19.3
2.19.4
2.19.5
2.20
Flat panel display connector (CN18) ............................ 21
Extension flat panel connector (CN17) ........................ 21
LVDS LCD panel connector (CN21) ........................... 21
Panel type selection (S1)............................................... 22
Ethernet configuration..................................................... 22
2.20.1 100Base-T connector (CN15)....................................... 23
2.20.2 Network boot ................................................................ 23
2.20.3 LAN controller power select (JP2) ............................... 23
2.21
Watchdog timer configuration ........................................ 23
2.21.1 Watchdog timer action (JP4) ........................................ 23
2.22
Chapter
USB connectors (CN4, CN23) ........................................ 24
3 Software Configuration .................................25
3.1
3.2
Introduction ..................................................................... 26
Connections to Three Standard LCDs............................. 27
3.2.1
3.2.2
3.2.3
3.3
Chapter
Ethernet software configuration ...................................... 30
4 Award BIOS Setup.........................................33
4.1
System test and initialization........................................... 34
4.1.1
4.2
System configuration verification................................. 34
Award BIOS setup .......................................................... 35
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
4.2.7
4.2.8
4.2.9
4.2.10
4.2.11
4.2.12
4.2.13
Chapter
Connections to (640 x 480 TFT color LCD) ............... 27
Connections to (1024 x 768 TFT color LCD) ............. 28
Connections to (800 x 600 TFT color LCD) ............... 29
Entering setup .............................................................. 35
Standard CMOS Features setup.................................... 36
Advanced BIOS Features setup .................................... 37
Advanced Chipset Features setup ................................. 38
Integrated Peripherals ................................................... 39
Power Management Setup ............................................ 39
PnP/PCI Configurations................................................ 40
PC Health Status ........................................................... 40
Frequency/Voltage Control........................................... 41
Load Optimized Defaults.............................................. 42
Set Password ................................................................. 42
Save & Exit Setup......................................................... 43
Exit Without Saving...................................................... 44
5 PCI SVGA Setup ............................................45
5.1
Introduction ..................................................................... 46
5.1.1
5.1.2
5.1.3
5.1.4
5.2
Chipset .......................................................................... 46
Display memory............................................................ 46
Display types................................................................. 46
Dual/Simultaneous Display .......................................... 47
Installation of the SVGA Driver ..................................... 48
vi
Table of Contents
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.3
Chapter
Further Information ......................................................... 73
6 Audio Setup.....................................................75
6.1
6.2
Introduction ..................................................................... 76
DOS utilities.................................................................... 76
6.2.1
6.2.2
6.3
VIA Sound Blaster Pro compatible set up program ..... 76
VIA Sound Blaster Installation..................................... 76
Driver installation............................................................ 77
6.3.1
6.3.2
6.3.3
6.3.4
Chapter
Installation for Windows 95 ......................................... 48
Installation for Windows 98/Me ................................... 52
Installation for Windows NT ........................................ 57
Installation for Windows 2000 ..................................... 62
Installation for Windows XP ........................................ 67
Before you begin........................................................... 77
Windows 95/98 drivers................................................. 77
Windows NT drivers..................................................... 85
Windows 2000 Drivers ................................................. 88
7 PCI Bus Ethernet Interface...........................93
7.1
7.2
Introduction ..................................................................... 94
Installation of Ethernet driver ......................................... 94
7.2.1
7.2.2
7.2.3
7.2.4
7.3
Installation for MS-DOS and Windows 3.1.................. 94
Installation for Windows 98 ......................................... 95
Installation for Windows 2000 ..................................... 98
Installation for Windows NT ...................................... 103
Further information ....................................................... 109
Appendix A Programming the Watchdog Timer ...........111
A.1
Supported Input Timing Modes .................................... 112
Appendix B Installing PC/104 Modules ..........................115
Appendix C Pin Assignments ...........................................121
C.1
C.2
C.3
C.4
C.5
C.6
C.7
C.8
C.9
C.10
C.11
C.12
C.13
CPU Fan Power Connector (FAN 1)............................. 122
Ethernet 10/100Base-T Connector (CN15)................... 122
Audio Connector (CN10) .............................................. 123
Main Power Connector (CN11) .................................... 124
Keyboard and PS/2 Mouse Connector (CN25) ............. 125
Floppy Disk Drive Connector (CN6) ............................ 126
IDE Hard Drive Connector (CN1, CN7) ...................... 127
Parallel Port Connector (CN2) ...................................... 128
HDD, PWR LED CON & WDT output (CN13)........... 129
Reset Button Connector (CN8) ..................................... 129
USB Connector (CN20, CN28)..................................... 130
LCD Inverter Backlight Connector (CN27).................. 130
IR Connector (CN9) ...................................................... 131
vii
C.14
C.15
C.16
C.17
C.18
C.19
C.20
C.21
C.22
C.23
CRT Display Connector (CN12)................................... 131
Flat Panel Connector (CN18)........................................ 132
Extended Flat Panel Display Connector (CN17) .......... 133
LCD Signal Mapping .................................................... 134
LVDS Connector (CN21).............................................. 135
COM Port Connector (CN19, CN20)............................ 136
CompactFlash Card Connector (CN28) ........................ 137
ATX Power Feature Connector (CN3).......................... 138
LCD Backlight Connector (CN24) ............................... 138
External Keyboard Connector (CN26).......................... 139
Appendix D System Assignments .....................................141
D.1
D.2
D.3
D.4
System I/O Ports............................................................ 142
1st MB memory map..................................................... 143
DMA channel assignments............................................ 143
Interrupt assignments .................................................... 144
Appendix E Optional Extras for the PCI-6871...............145
E.1
E.2
E.3
Optional USB cable (CN20) ......................................... 146
ATX Power Control Cable............................................ 146
Audio module................................................................ 146
viii
CHAPTER
1
General Information
This chapter gives background
information on the PCI-6871.
Sections include:
•
•
•
•
Introduction
Features
Specifications
Board layout and dimensions
1
Chapter 1 General Information
Chapter 1 Introduction
1.1 Introduction
The new PCI-6871 is a half-sized CPU card with onboard VIA
Eden400 C3 EBGA fanless CPU. The VIA Eden processor uses advanced
0.13µ CMOS technology with 128KB L1 cache memory and 64KB L2
cache memory on die. This board with Eden400 CPU can operate without
a fan at temperatures up to 60° C (140° F) and typically consumes under
14 Watts while supporting numerous peripherals. This SBC includes a 4X
AGP controller, a PCI Ethernet interface, and 36-bit TTL interface. Its
design is based on the half-sized CPU card and supports PCI bus expansion. Other on-board features include an FDD, LPT, 4 USBs, and 2 serial
ports. PCI-6871 supports AC97 audio with the addition of the optional
PCM-231A-00A1 audio module. This product uses a VIA VT8606
"TwisterT" chip with Integrated Savage4 2D/3D/Video Accelerator and
supports 4X AGP VGA/LCD interface and up to 32 MB frame buffer
using system memory. The PCI-6871 supports one 10/100Mbps Ethernet
connection with an onboard RJ-45 connector, and is effective for use as a
firewall, VPN, or other communication device.
PCI-6871 User’s Manual
2
1.2 Features
• Embedded low power VIA Eden C3 EGBA 400MHz processor
• Half-sized CPU card with PCI golden finger
• Fanless operation at 60° C.
• 1 onboard RJ-45 connector supports 10/100Base-T Ethernet
• 4X AGP graphics for high performance applications
• Supports PC/104
• Supports wake on LAN
• Supports wake on Modem
• Supports LCD backlight turn-off function
1.3 Specifications
1.3.1 Standard SBC Functions
• CPU: VIA C3 fanless EBGA 400MHz processor
• System chipset: VIA VT8606 "TwisterT" +VT82C686B
• BIOS: Award 256 KB Flash memory
• System memory: Two 144-pin SODIMM sockets (on the backside)
accept 32 MB up to 512MBx2 (total 1024MB) SDRAM
• 2nd cache memory: 64KB on the C3 fanless EBGA 400MHz processor
• FDD interface: Supports up to two FDDs
• Serial ports: Two serial ports:
COM1: RS-232
COM2: RS-232/422/485
• Parallel port: Parallel port supports SPP/EPP/ECP mode
3
Chapter 1 General Information
• Keyboard/mouse connector: Supports standard PC/AT keyboard
and a PS/2 mouse
• Power management: Supports power saving modes including Normal/Standby/Suspend modes. APM 1.2 compliant
• Watchdog timer: 62 level timer intervals
• USB: Four universal serial bus ports
• PC/104 expansion: PC/104 connector for ISA control board
• Solid State Disk: Supports one 50-pin socket for CFC type I/II
1.3.2 VGA/LCD/LVDS Interface
• Chipset: VIA TwisterT chip with integrated Savage4 2D/3D/Video Accelerator
• Frame buffer: Supports 8/16/32 MB frame buffer with system memory
• Interface: 4X AGP VGA/LCD interface, Support for 9, 12, 15, 18, 24,
36 bit TFT and optional 16- or 24-bit DSTN panel
• Display mode: CRT Modes: 1280 x 1024@32bpp (60Hz), 1024 x 768
@ 32bpp (85 Hz); LCD/Simultaneous Modes: 1280 x 1024 @16bpp
(60 Hz), 1024 x 768 @16bpp (60Hz)
1.3.3 LVDS: Supports 2 Channel (2 x 18 bit) LVDS interface
• Chipset: VIA VT8606T (TwisterT)
1.3.4 PCI bus Ethernet interface
• Chipset: REALTEK RTL8139 Ethernet controller
• Ethernet interface: IEEE 802.3U compatible 100/10Base-T interface.
Includes software drivers and boot ROM
• Wake-on-LAN: Supports wake-on-LAN function with ATX power control
1.3.5 Mechanical and Environmental
• Dimensions (L x W): 185 x 122 mm (7.28” x 4.80”)
• Power supply voltage: +5 V ±5%, +12V ±5%
• Power requirements:
Max:
10.33A @ +5V,205mA@+12V
(with 128 MB SDRAM,VIA C3-400MHz CPU)
Typical: 2.37A @ +5V,34.02mA@+12V
(with 256 MB SDRAM,VIA C3-400MHz CPU)
• Operating temperature: 0 ~ 60°C (32 ~ 140°F)
• Weight: 0.27 kg (weight of total package)
PCI-6871 User’s Manual
4
1.4 Board layout: dimensions
+
PCI-6871 REV.A1
I
Figure 1.1: Board layout: dimensions (component side)
5
Chapter 1 General Information
PCI-6871 REV.A1
+
Figure 1.2: Board layout: dimensions (solder side)
PCI-6871 User’s Manual
6
CHAPTER
2
Installation
This chapter explains the setup procedures
of PCI-6871 hardware, including instructions on setting jumpers and connecting
peripherals, switches and indicators. Be
sure to read all safety precautions before
you begin the installation procedure.
7
Chapter 2 Installation
Chapter 2 Installation
2.1 Jumpers
The PCI-6871 has a number of jumpers that allow you to configure your
system to suit your application. The table below lists the functions of the
various jumpers.
Table 2.1: Jumpers
Label
Function
JP1
CMOS clear
JP2
LAN power select
JP3
RS-232/422/485 select
JP4
Watch-Dog output selct
S1
Panel type select
2.2 Connectors
On-board connectors link the PCI-6871 to external devices such as hard
disk drives, a keyboard, or floppy drives. The table below lists the function of each of the board’s connectors.
Table 2.2: Connectors
Label
Function
CN1
Primary IDE
CN2
LPT
CN3
ATX Power feature connector
CN4
USB1,2
CN5
PWR_SW
CN6
Floppy
CN7
Secondary IDE
CN8
Reset
PCI-6871 User’s Manual
8
Table 2.2: Connectors
CN9
IR CON
CN10
Audio I/F
CN11
MAIN PWR CON
CN12
D-SUB VGA
CN13
HDD, PWR LED CON & WDT Output
CN14
DIO CON
CN15
LAN RJ45 CON
CN16
PC104
CN17
LCD CON2 (10*2)
CN18
LCD CON1 (20*2)
CN19
COM1
CN20
COM2
CN21
LVDS CON
CN23
USB3,4
CN24
LCD backlight
CN25
PS/2 KB/MS
CN26
EXT_KB
CN27
LCD INV PWR
CN28
CF CON
FAN1
CPU fan power
9
Chapter 2 Installation
2.3 Locating jumpers
+
PCI-6871 REV.A1
I
Figure 2.1: Jumper locations
PCI-6871 User’s Manual
10
2.4 Locating Connectors
+
PCI-6871 REV.A1
I
Figure 2.2: Connectors (component side)
11
Chapter 2 Installation
2.5 Setting Jumpers
You may configure your card to match the needs of your application by
setting jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two metal pins and a small metal clip (often protected
by a plastic cover) that slides over the pins to connect them. To “close” a
jumper, you connect the pins with the clip. To “open” a jumper, you
remove the clip. Sometimes a jumper will have three pins, labeled 1, 2
and 3. In this case you would connect either pins 1 and 2, or 2 and 3.
open
closed
closed 2-3
The jumper settings are schematically depicted in this manual as follows:.
open
closed
closed 2-3
A pair of needle-nose pliers may be helpful when working with jumpers.
If you have any doubts about the best hardware configuration for your
application, contact your local distributor or sales representative before
you make any changes.
Generally, you simply need a standard cable to make most connections.
PCI-6871 User’s Manual
12
2.6 Clear CMOS (JP1)
Warning!
To avoid damaging the computer, always turn
off the power supply before setting “Clear
CMOS.” Before turning on the power supply,
set the jumper back to “3.0 V Battery On.”
This jumper is used to erase CMOS data and reset system BIOS information.
The procedure for clearing CMOS is:
1.
Turn off the system.
2.
Short pin 2 and pin 3.
3.
Return jumper to pins 1 and 2.
4.
Turn on the system. The BIOS is now reset to its default setting
Table 2.3: CMOS clear (JP1)
*3.0 V Battery on
Clear CMOS
* default setting
13
Chapter 2 Installation
2.7 Installing system memory (SODIMMs)
You can install anywhere from 32 to 512 MB of SDRAM into your PCI-6871 Series card. The card provides two 144-pin SODIMM sockets. Each socket accepts 32/64/128/256/512 MB 3.3 V power level SODIMMs. If only one SODIMM
module is installed, it may be installed in either SODIMM socket on the solder
side of the PCI-6871 Series card.
Note:
PCI-6871 Series cards only support SDRAM SODIMM
modules. EDO SODIMM is not supported.
2.7.1 Installing SODIMMs
Note:
The modules can only fit into a socket one way. The gold
pins must point down into the SODIMM socket.
The procedure for installing SODIMMs appears below. Please follow these
steps carefully.
1.
Make sure that all power supplies to the system are switched off.
2.
Install the SODIMM card. Install the SODIMM so that its gold pins
point down into the SODIMM socket.
3.
Slip the SODIMM into the socket at a 45 degree angle and carefully fit the bottom of the card against the connectors.
4.
Gently push the SODIMM into a perpendicular position until the
clips on the ends of the SODIMM sockets snap into place.
5.
Check to ensure that the SODIMM is correctly seated and all connector contacts touch. The SODIMM should not move around in its
socket.
PCI-6871 User’s Manual
14
Important:
Only use standard form SODIMM memory modules (as
shown in the diagram below). Standardized dimensions
ensure a proper fit. Check with your memory supplier
about the SODIMM modules you will use.
Figure 2.3: SODIMM module
2.8 IDE, CDROM hard drive connector (CN1, CN7)
The PCI-6871 provides 2 IDE channels which you can attach up to four
Enhanced Integrated Device Electronics hard disk drives or CDROM to
the PCI-6871’s internal controller. The PCI-6871's IDE controller uses a
PCI interface. This advanced IDE controller supports faster data transfer,
PID mode 3, mode 4 and UDMA/100. The secondary channel supports
UDMA/33 only.
15
Chapter 2 Installation
2.8.1 Connecting the hard drive
Connecting drives is done in a daisy-chain fashion. It requires one of two
cables (not included in this package), depending on the drive size. 1.8"
and 2.5" drives need a 1 x 44-pin to 2 x 44-pin flat-cable connector. 3.5"
drives use a 1 x 44-pin to 2 x 40-pin connector.
Wire number 1 on the cable is red or blue, and the other wires are gray.
1.
Connect one end of the cable to CN1 or CN7. Make sure that the
red (or blue) wire corresponds to pin 1 on the connector, which is
labeled on the board (on the right side).
2.
Plug the other end of the cable into the Enhanced IDE hard drive,
with pin 1 on the cable corresponding to pin 1 on the hard drive.
(See your hard drive’s documentation for the location of the connector.)
If desired, connect a second drive as described above.
Unlike floppy drives, IDE hard drives can connect to either end of the
cable. If you install two drives, you will need to set one as the master and
one as the slave by using jumpers on the drives. If you install only one
drive, set it as the master.
2.9 Solid State Disk
The PCI-6871 provides a 50-pin socket for CompactFlash card type I/II.
2.9.1 CompactFlash (CN28)
The CompactFlash card shares a secondary IDE channel which can be
enabled/disabled via the BIOS settings.
2.10 Floppy drive connector (CN6)
You can attach up to two floppy drives to the PCI-6871’s on-board controller. You can use any combination of 5.25” (360 KB and 1.2 MB) and/
or 3.5” (720 KB, 1.44 MB, and 2.88 MB) drives.
A 34-pin daisy-chain drive connector cable is required for a dual-drive
system. On one end of the cable is a 34-pin flat-cable connector. On the
other end are two sets of floppy disk drive connectors. Each set consists
of a 34-pin flat-cable connector (usually used for 3.5” drives) and a
printed-circuit board connector (usually used for 5.25” drives).
PCI-6871 User’s Manual
16
2.10.1 Connecting the floppy drive
1.
Plug the 34-pin flat-cable connector into CN6. Make sure that the
red wire corresponds to pin one on the connector.
2.
Attach the appropriate connector on the other end of the cable to
the floppy drive(s). You can use only one connector in the set. The
set on the end (after the twist in the cable) connects to the A: drive.
The set in the middle connects to the B: drive.
3.
If you are connecting a 5.25” floppy drive, line up the slot in the
printed circuit board with the blocked-off part of the cable connector.
If you are connecting a 3.5” floppy drive, you may have trouble determining which pin is number one. Look for a number printed on the circuit
board indicating pin number one. In addition, the connector on the floppy
drive may have a slot. When the slot is up, pin number one should be on
the right. Check the documentation that came with the drive for more
information.
If you desire, connect the B: drive to the connectors in the middle of the
cable as described above.
In case you need to make your own cable, you can find the pin assignments for the board’s connector in Appendix C.
2.11 Parallel port connector (CN2)
Normally, the parallel port is used to connect the card to a printer. The
PCI-6871 includes a multi-mode (ECP/EPP/SPP) parallel port accessed
via CN2 and a 26-pin flat-cable connector. You will need an adapter cable
if you use a traditional DB-25 connector. The adapter cable has a 26-pin
connector on one end, and a DB-25 connector on the other.
The parallel port is designated as LPT1, and can be disabled or changed to
LPT2 or LPT3 in the system BIOS setup.
The parallel port interrupt channel is designated to be IRQ7.
You can select ECP/EPP DMA channel via BIOS setup.
2.12 Keyboard and PS/2 mouse connector (CN25)
The PCI-6871 board provides a keyboard connector that supports both a
keyboard and a PS/2 style mouse. In most cases, especially in embedded
applications, a keyboard is not used. If the keyboard is not present, the
17
Chapter 2 Installation
standard PC/AT BIOS will report an error or fail during power-on selftest (POST) after a reset. The PCI-6871’s BIOS standard setup menu
allows you to select “All, But Keyboard” under the “Halt On” selection.
This allows no-keyboard operation in embedded system applications,
without the system halting under POST.
2.13 Power & HDD LED, Reset Button Connector
(CN13, CN8)
Next, you may want to install external switches to monitor and control the
PCI-6871. These features are optional: install them only if you need
them. The front panel connector (CN13) is an 8-pin male, dual in-line
header. It provides connections for a speaker, hard disk access indicator,
watchdog output, and an input switch for resetting the card.
2.13.1 Power & HDD LED (CN13)
The HDD LED indicator for hard disk access is an active low signal (24
mA sink rate). Power supply activity LED indicator.
2.13.2 Reset switch (CN8)
If you install a reset switch, it should be an open single pole switch.
Momentarily pressing the switch will activate a reset. The switch should
be rated for 10 mA, 5 V.
2.14 Power connectors (CN11, FAN1)
2.14.1 Main power connector, +5 V, +12 V (CN11)
Supplies main power to the PCI-6871 (+5 V), and to devices that require
+12 V.
2.14.2 CPU Fan power supply connector (FAN1)
Provides power supply to CPU cooling fan. Only present when +5 V and
+12 V power is supplied to the board.
PCI-6871 User’s Manual
18
2.15 ATX power control connector (CN3, CN5)
2.15.1 ATX feature connector (CN3) and soft power
switch connector (CN5)
The PCI-6871 can support an advanced soft power switch function, if an
ATX power supply is used. To enable the soft power switch function:
1.
Get the specially designed ATX-to-EBX power cable
(PCI-6871 optional item, part no. 1703200100)
2.
Connect the 3-pin plug of the cable to CN3 (ATX feature connector).
3.
Connect the power on/off button to CN5. (A momentary type of
button should be used.)
Important
Make sure that the ATX power supply can take
at least a 10 mA load on the 5 V standby lead
(5VSB). If not, you may have difficulty powering on your system.
to CN3 ATX
features connector
ATX
power supply
to main power
connector CN11
20-pin
female connector
Figure 2.4: Wiring for ATX soft power switch function
19
Chapter 2 Installation
2.16 IR connector (CN9)
This connector supports the optional wireless infrared transmitting and
receiving module. This module mounts on the system case. You must
configure the setting through BIOS setup.
2.17 Audio interfaces (CN10)
The Audio link is a 10 pin connector; the PCI-6871 can support AC97
Audio with the addition of optional PCM-231A-00A1.
2.18 COM port connector (CN19, CN20)
The PCI-6871 provides two serial ports (COM1:RS-232; COM2: RS232/422/485) in one COM port connector. The COM port connector is a
40-pin, dual-inline, male header. It provides connections for serial
devices (a mouse, etc.) or a communication network. You can find the pin
assignments for the COM port connector in Appendix C.
2.18.1 COM2 RS-232/422/485 setting (JP3)
COM2 can be configured to operate in RS-232, RS-422, or RS-485 mode.
This is done via JP3
JP3: COM2 RS-232/422/485 select
PINS
RS-232*
RS-422
RS-485
1-2
Closed
Open
Open
3-4
Open
Closed
Open
5-6
Open
Open
Closed
2.19 VGA/LCD/LVDS interface connections
The PCI-6871’s PCI SVGA interface can drive conventional CRT displays and is capable of driving a wide range of flat panel displays, including passive LCD and active LCD displays. The board has three
connectors to support these displays: one for standard CRT VGA monitors, one for flat panel displays, and one for LVDS type LCD panels.
PCI-6871 User’s Manual
20
2.19.1 CRT display connector (CN12)
CN12 is a standard 15-pin D-SUB connector commonly used for VGA.
The pin assignments for CRT display connector CN12 are detailed in
Appendix C.
2.19.2 Flat panel display connector (CN18)
CN18 consists of a 40-pin connector which can support a 24-bit LCD
panel. It is Hirose’s product no. DF13A-40DP-1.25 V
The PCI-6871 provides a bias control signal on CN18 that can be used to
control the LCD bias voltage. It is recommended that the LCD bias voltage not be applied to the panel until the logic supply voltage (+5 V or
+3.3 V) and panel video signals are stable. Under normal operation, the
control signal (ENAVEE) is active high. When the PCI-6871’s power is
applied, the control signal is low until just after the relevant flat panel signals are present. CN18 can connect up to 24 bit TFT LCD.
2.19.3 Extension flat panel connector (CN17)
CN17 consists of a 20-pin connector which is Hirose’s product no.
DF13A-20DP-1.25V. The PCI-6871 supports a 36-bit LCD panel which
must be connected to both the CN18 (40-pin) and the CN17 (20-pin). The
pin assignments for both CN18and the CN17 can be found in Appendix C
2.19.4 LVDS LCD panel connector (CN21)
The PCI-6871 uses the VIA TwisterT chip that supports 2 channel (2 x
18 bit) LVDS LCD panel displays. Users can connect to either an 18-bit
or 36-bit LVDS LCD with CN21.
21
Chapter 2 Installation
2.19.5 Panel type selection (S1)
S1 is an 8 segment DIP switch for DSTN/TFT panel type and resolution
functions.
Table 2.4: S1 Panel Type select
SW
1-1
SW
1-2
SW
1-3
SW
1-4
Panel Type & Resolution
ON
ON
ON
ON
TFT
640x480**
18bit (H. V. Freq)
ON
ON
ON
OFF
TFT
648x480
18bit (Synthetic)
ON
ON
OFF ON
TFT
648x480**
N/A
ON
ON
OFF OFF
TFT
648x480**
LVDS
ON
OFF
ON
ON
DSTN
648x480**
18bit
ON
OFF
ON
OFF
TFT
800x600**
18bit (H. V. Freq)
ON
OFF
OFF ON
TFT
800x600*
18bit (Synthetic)
ON
OFF
OFF OFF
TFT
800x600
LVDS
OFF
ON
ON
ON
TFT
800x600**
N/A
OFF
ON
ON
OFF
DSTN
800x600**
18bit
OFF
ON
OFF ON
TFT
1024x768** 36bit (H. V. Freq)
OFF
ON
OFF OFF
TFT
1024x768
OFF
OFF
ON
ON
TFT
1024x768** LVDS
OFF
OFF
ON
OFF
TFT
1024x768** N/A
OFF
OFF
OFF ON
DSTN
1024x768** 18bit
OFF
OFF
OFF OFF
DSTN
1024x768** 24bit
36bit (Synthetic)
* Default setting
** will support in the future
2.20 Ethernet configuration
The PCI-6871 is equipped with a high performance 32-bit PCI-bus Ethernet interface which is fully compliant with IEEE 802.3U 10/100Mbps
CSMA/CD standards. It is supported by all major network operating systems.
The medium type can be configured via the RSET8139.EXE program
included on the utility disk. (See Chapter 3 for detailed information.)
PCI-6871 User’s Manual
22
2.20.1 100Base-T connector (CN15)
CN15 is an RJ-45 connector with LED..
2.20.2 Network boot
The Network Boot feature can be utilized by incorporating the Boot
ROM image files for the appropriate network operating system. The Boot
ROM BIOS files are included in the system BIOS, which is on the utility
CD disc.
2.20.3 LAN controller power select (JP2)
Table 2.5: LAN controller power select (JP2)
3.3 V*
Standby 3.3V
* default setting
Note: PCI-6871 supports Wake-on-LAN. For Wake-on LAN, J6 has to be
set to the Standby 3.3 V position
2.21 Watchdog timer configuration
An on-board watchdog timer reduces the chance of disruptions which
EMP (electro-magnetic pulse) interference can cause. This is an invaluable protective device for standalone or unmanned applications. Setup
involves one jumper and running the control software (refer to Appendix
A).
2.21.1 Watchdog timer action (JP4)
When the watchdog timer activates (CPU processing has come to a halt),
it can reset the system or generate an interrupt on IRQ11. This can be set
via setting JP4 as shown below:
23
Chapter 2 Installation
Table 2.6: Watchdog timer action (JP4)
*System reset
IRQ 11
* default setting
2.22 USB connectors (CN4, CN23)
The PCI-6871 board provides up to four USB (Universal Serial Bus)
ports, with USB3 and USB4 optional. This gives complete Plug and Play,
and hot attach/detach for up to 127 external devices. The USB interfaces
comply with USB specification Rev. 1.1, and are fuse protected.
The USB interface is accessed through two 5 x 2-pin flat-cable connectors, CN4 (USB1, 2); and CN23 (USB3, 4). You will need an adapter
cable if you use a standard USB connector. The adapter cable has a 5 x 2pin connector on one end and a USB connector on the other.
The USB interfaces can be disabled in the system BIOS setup.
PCI-6871 User’s Manual
24
CHAPTER
3
Software Configuration
This chapter details the software configuration information. It shows you how to configure the card to match your application
requirements. The AWARD System BIOS is
covered in Chapter 4.
Sections include:
•
•
•
Introduction
Connections for standard LCDs
Ethernet interface configuration.
25
Chapter 3 Software Configuration
Chapter 3 Software Configuration
3.1 Introduction
The PCI-6871 system BIOS and custom drivers are located
in a 256 Kbyte, Flash ROM device, designated U18. A single
Flash chip holds the system BIOS, VGA BIOS and network
Boot ROM image. The display can be configured via CMOS
settings. This method minimizes the number of chips and difficulty of configuration. To set different types of LCD panels, please choose “panel type” from the “integrated
peripherals” menu in CMOS setup.
PCI-6871 User’s Manual
26
3.2 Connections to Three Standard LCDs
The following tables illustrate typical LCD connection pinouts for the
PCI-6871.
3.2.1 Connections to Toshiba LTM10C209A (640 x 480 TFT color LCD)
Table 3.1: Connections to Toshiba LTM10C209A
LTM10C209A
PCI-6871 CN18
Pin
Name
Pin
Name
1
GND
3
GND
2
CLK
35
SHFCLK
3
GND
34
GND
4
R0
27
P18
5
R1
28
P19
6
R2
29
P20
7
GND
33
GND
8
R3
30
P21
9
R4
31
P22
10
R5
32
P23
11
GND
34
GND
12
G0
19
P10
13
G1
20
P11
14
G2
21
P12
15
GND
8
GND
16
G3
22
P13
17
G4
23
P14
18
G5
24
P15
19
GND
8
GND
20
ENAB
37
M/DE
21
GND
4
GND
22
B0
11
P2
23
B1
12
P3
24
B2
13
P4
25
GND
4
GND
26
B3
14
P5
27
B4
15
P6
27
Chapter 3 Software Configuration
Table 3.1: Connections to Toshiba LTM10C209A
28
B5
16
P7
29
GND
3
GND
30
VDD
1
+5 V
31
VDD
2
+5 V
3.2.2 Connections to Toshiba LTM15C151A (1024 x 768 TFT color LCD)
Table 3.2: Connections to Toshiba LTM15C151A
LTM15C151A
PCI-6871 CN18
Pin
Name
Pin
Name
CN1-1
GND
CN 11-33
GND
CN1-2
NCLK
CN 11-35
LDSCLK1
CN1-3
NC
CN1-4
NC
CN1-5
GND
CN 11-3
GND
CN1-6
OR0
CN 11-9
PD0
CN1-7
OR1
CN 11-11
PD2
CN1-8
OR2
CN 11-13
PD4
CN1-9
OR3
CN 11-15
PD6
CN1-10
OR4
CN 11-17
PD8
CN1-11
OR5
CN 11-19
PD10
CN1-12
GND
CN 11-3
GND
CN1-13
OG0
CN 11-21
PD12
CN1-14
OG1
CN 11-23
PD14
CN1-15
OG2
CN 11-25
PD16
CN1-16
OG3
CN 11-27
PD18
CN1-17
OG4
CN 11-29
PD20
CN1-18
OG5
CN 11-31
PD22
CN1-19
GND
CN 10-1
GND
CN1-20
OB0
CN 10-3
PD24
CN1-21
OB1
CN 10-5
PD26
CN1-22
OB2
CN 10-7
PD28
CN1-23
OB3
CN 10-9
PD30
CN1-24
OB4
CN 10-11
PD32
PCI-6871 User’s Manual
28
Table 3.2: Connections to Toshiba LTM15C151A
CN1-25
OB5
CN 10-13
PD34
CN1-26
ENAB
CN 11-37
M/DE
CN1-27
GND
CN 11-34
GND
CN1-28
VDD
CN 11-1
+5V
CN1-29
VDD
CN 11-2
+5V
CN1-30
GND
CN 11-8
GND
3.2.3 Connections to Toshiba LTM12C275A (800 x 600 TFT color LCD)
Table 3.3: Connections to Toshiba LTM12C275A
LTM12C275A
PCI-6871 CN18
Pin
Name
Pin
Name
1
GND
3
GND
2
NCLK
35
SHFCLK
3
NC
-
NC
4
NC
-
NC
5
GND
4
GND
6
R0
27
P18
7
R1
28
P19
8
R2
29
P20
9
R3
30
P21
10
R4
31
P22
11
R5
32
P23
12
GND
8
GND
13
G0
19
P10
14
G1
20
P11
15
G2
21
P12
16
G3
22
P13
17
G4
23
P14
18
G5
24
P15
19
GND
33
GND
20
B0
11
P2
21
B1
12
P3
22
B2
13
P4
29
Chapter 3 Software Configuration
Table 3.3: Connections to Toshiba LTM12C275A
23
B3
14
P5
24
B4
15
P6
25
B5
16
P7
26
ENAB
37
M/DE
27
GND
34
GND
28
VCC
5
+5 V
29
VCC
6
+5 V
30
GND
39
GND
3.3 Ethernet software configuration
The PCI-6871’s on-board Ethernet interface supports all major network
operating systems. To configure the medium type, to view the current
configuration, or to run diagnostics, do the following:
1.
Power the PCI-6871 on. Make sure that the RSET8139.EXE file is
located in the working drive.
2.
At the prompt, type RSET8139.EXE and press <Enter>. The Ethernet configuration program will then be displayed.
3.
This simple screen shows all the available options for the Ethernet
interface. Just highlight the option you wish to change by using the
Up and Down keys. To change a selected item, press <Enter>, and
a screen will appear with the available options. Highlight your
option and press <Enter>. Each highlighted option has a helpful
message guide displayed at the bottom of the screen for additional
information.
4.
After you have made your selections and are sure this is the configuration you want, press ESC. A prompt will appear asking if you
want to save the configuration. Press Y if you want to save.
The Ethernet Setup Menu also offers three very useful diagnostic functions. These are:
1.
Run EEPROM Test.
2.
Run Diagnostics on Board.
3.
Run Diagnostics on Network.
Each option has its own display screen that shows the format and result of
any diagnostic tests undertaken.
PCI-6871 User’s Manual
30
Note
For Ethernet installation, please see Chapter 7
31
Chapter 3 Software Configuration
PCI-6871 User’s Manual
32
CHAPTER
4
Chapter 4 Ducks that Need Love!
Award BIOS Setup
This chapter describes how to set BIOS
configuration data.
33
Chapter 4 Award BIOS Setup
Chapter 4 Award BIOS Setup
4.1 System test and initialization
These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see
an error message on the screen. There are two kinds of errors: fatal and
non-fatal. The system can usually continue the boot up sequence with
non-fatal errors. Non-fatal error messages usually appear on the screen
along with the following instructions:
press <F1> to RESUME
Write down the message and press the F1 key to continue the bootup
sequence.
4.1.1 System configuration verification
These routines check the current system configuration against the values
stored in the board’s CMOS memory. If they do not match, the program
outputs an error message. You will then need to run the BIOS setup program to set the configuration information in memory.
There are three situations in which you will need to change the CMOS
settings:
1.
You are starting your system for the first time
2.
You have changed the hardware attached to your system
3.
The CMOS memory has lost power and the configuration information has been erased.
The PCI-6871 Series' CMOS memory has an integral lithium battery
backup. The battery backup should last ten years in normal service, but
when it finally runs down, you will need to replace the complete unit.
PCI-6871 User’s Manual
34
4.2 Award BIOS setup
Award’s BIOS ROM has a built-in Setup program that allows users to
modify the basic system configuration. This type of information is stored
in battery-backed CMOS RAM so that it retains the Setup information
when the power is turned off.
4.2.1 Entering setup
Power on the computer and press <Del> immediately. This will allow you
to enter Setup.
Figure 4.1: BIOS setup program initial screen
35
Chapter 4 Award BIOS Setup
4.2.2 Standard CMOS Features setup
When you choose the Standard CMOS Features option from the Initial
Setup Screen menu, the screen shown below is displayed. This standard
Setup Menu allows users to configure system components such as date,
time, hard disk drive, floppy drive and display. Once a field is highlighted, on-line help information is displayed in the left bottom of the
Menu screen.
Figure 4.2: CMOS Features setup
PCI-6871 User’s Manual
36
4.2.3 Advanced BIOS Features setup
By choosing the Advanced BIOS Features Setup option from the Initial
Setup Screen menu, the screen below is displayed. This sample screen
contains the manufacturer’s default values for the PCI-6871 Series.
Figure 4.3: Advanced BIOS Features setup
37
Chapter 4 Award BIOS Setup
4.2.4 Advanced Chipset Features setup
By choosing the Advanced Chipset Features option from the Initial Setup
Screen menu, the screen below is displayed. This sample screen contains
the manufacturer’s default values for the PCI-6871 Series.
Figure 4.4: Advanced Chipset Features setup
PCI-6871 User’s Manual
38
4.2.5 Integrated Peripherals
Choosing the Integrated Peripherals option from the Initial Setup Screen
menu should produce the screen below. Here we see the manufacturer’s
default values for the PCI-6871 Series.
Figure 4.5: Integrated Peripherals
4.2.6 Power Management Setup
By choosing the Power Management Setup option from the Initial Setup
Screen menu, the screen below is displayed. This sample screen contains
the manufacturer’s default values for the PCI-6871 Series.
Figure 4.6: Power Management Setup
39
Chapter 4 Award BIOS Setup
4.2.7 PnP/PCI Configurations
By choosing the PnP/PCI Configurations option from the Initial Setup
Screen menu, the screen below is displayed. This sample screen contains
the manufacturer’s default values for the PCI-6871 Series.
Figure 4.7: PnP/PCI Configurations
4.2.8 PC Health Status
The PC Health Status option displays information such as CPU and motherboard temperatures, fan speeds, and core voltage.
Figure 4.8: PC Health Status
PCI-6871 User’s Manual
40
4.2.9 Frequency/Voltage Control
By choosing the Frequency/Voltage Control option from the Initial Setup
Screen menu, the screen below is displayed. This sample screen contains
the manufacturer’s default values for the PCI-6871
Figure 4.9: Frequency/Voltage Control
Caution
Incorrect settings in Frequency/Voltage Control
may damage the system CPU, video adapter,
or other hardware.
41
Chapter 4 Award BIOS Setup
4.2.10 Load Optimized Defaults
Load Optimized Defaults loads the default system values directly from
ROM. If the stored record created by the Setup program should ever
become corrupted (and therefore unusable), these defaults will load automatically when you turn the PCI-6871 Series system on.
Figure 4.10: Load BIOS defaults screen
4.2.11 Set Password
Note
To enable this feature, you should first go to the
Advanced BIOS Features menu, choose the
Security Option, and select either Setup or
System, depending on which aspect you want
password protected. Setup requires a password only to enter Setup. System requires the
password either to enter Setup or to boot the
system.
A password may be at most 8 characters long.
To Establish Password
1.
Choose the Set Password option from the CMOS Setup Utility
main menu and press <Enter>.
2.
When you see “Enter Password,” enter the desired password and
press <Enter>.
PCI-6871 User’s Manual
42
3.
At the “Confirm Password” prompt, retype the desired password,
then press <Enter>.
4.
Select Save to CMOS and EXIT, type <Y>, then <Enter>.
To Change Password
1.
Choose the Set Password option from the CMOS Setup Utility
main menu and press <Enter>.
2.
When you see “Enter Password,” enter the existing password and
press <Enter>.
3.
You will see “Confirm Password.” Type it again, and press
<Enter>.
4.
Select Set Password again, and at the “Enter Password” prompt,
enter the new password and press <Enter>.
5.
At the “Confirm Password” prompt, retype the new password, and
press <Enter>.
6.
Select Save to CMOS and EXIT, type <Y>, then <Enter>.
To Disable Password
1.
Choose the Set Password option from the CMOS Setup Utility
main menu and press <Enter>.
2.
When you see “Enter Password,” enter the existing password and
press <Enter>.
3.
You will see “Confirm Password.” Type it again, and press
<Enter>.
4.
Select Set Password again, and at the “Enter Password” prompt,
don’t enter anything; just press <Enter>.
5.
At the “Confirm Password” prompt, again don’t type in anything;
just press <Enter>.
6.
Select Save to CMOS and EXIT, type <Y>, then <Enter>.
4.2.12 Save & Exit Setup
If you select this option and press <Y> then <Enter>, the values entered
in the setup utilities will be recorded in the chipset’s CMOS memory. The
microprocessor will check this every time you turn your system on and
use the settings to configure the system. This record is required for the
system to operate.
43
Chapter 4 Award BIOS Setup
4.2.13 Exit Without Saving
Selecting this option and pressing <Enter> lets you exit the Setup program without recording any new values or changing old ones.
PCI-6871 User’s Manual
44
CHAPTER
5
PCI SVGA Setup
•
•
•
Introduction
Installation of SVGA drivers
-for Windows 95/98/Me
-for Windows NT/2000/XP
Further information
45
Chapter 5 PCI SVGA Setup
Chapter 5 PCI SVGA Setup
5.1 Introduction
The PCI-6871 has an onboard AGP flat panel/VGA interface. The specifications and features are described as follows:
5.1.1 Chipset
The PCI-6871 uses a VIA TwisterT chipset from VIA Technology Inc.
for its AGP/SVGA controller. It supports many popular LCD, and LVDS
LCD displays and conventional analog CRT monitors. The VIA8606T
VGA BIOS supports color TFT and DSTN LCD flat panel displays. In
addition, it also supports interlaced and non-interlaced analog monitors
(color and monochrome VGA) in high-resolution modes while
maintaining complete IBM VGA compatibility. Digital monitors
(i.e. MDA, CGA, and EGA) are NOT supported. Multiple frequency
(multisync) monitors are handled as if they were analog monitors.
5.1.2 Display memory
The TwisterT chip can support 8/16/32MB frame buffer shared with system memory; the VGA controller can drive CRT displays or color panel
displays with resolutions up to 1280 x 1024 at 16 M colors.
5.1.3 Display types
CRT and panel displays can be used simultaneously. The PCI-6871 can
be set in one of three configurations: on a CRT, on a flat panel display, or
on both simultaneously. The system is initially set to simultaneous display mode. If you want to enable the CRT display only or the flat panel
display only, please contact VIA Technology Inc., or our sales representative for detailed information.
PCI-6871 User’s Manual
46
5.1.4 Dual/Simultaneous Display
The PCI-6871 uses a VIA Twister VT8606T LCD controller that is capable of providing simultaneous dual view display of the same content on a
flat panel and CRT.
To set up dual view (simultaneus mode) under Windows 9x, Windows
ME, Windows NT/2000/XP, follow these steps:
Step 1. Open the Control panel, and select “Display”, “Settings”.
Step 2. Select " CRT+LCD " or " CRT+TV " for dual view
Step 3. Click “OK”.
Figure 5.1: Selecting Display Settings
47
Chapter 5 PCI SVGA Setup
5.2 Installation of the SVGA Driver
Complete the following steps to install the SVGA driver. Follow the procedures in the flow chart that apply to the operating system that you are
using within your PCI-6871.
Notes:
1. The windows illustrations in this chapter are
intended as examples only. Please follow the
listed steps, and pay attention to the instructions which appear on your screen.
2. For convenience, the CD-ROM drive is designated as "D" throughout this chapter.
5.2.1 Installation for Windows 95
Step 1. Select "Start", "Settings", "Control Panel", "Display", "Settings”,
and "Advanced Properties".
PCI-6871 User’s Manual
48
Step 2. Choose the "Adapter" tab, then press the "Change..." button.
Step 3. Press the "Have Disk" button.
49
Chapter 5 PCI SVGA Setup
Step 4. Type in the path:
D:\slotPC\6871\VGA\Win9x_Me
D:\slotPC\6871\VGA\Win9x_Me
Step 5. Select the highlighted item, and click the "OK" button.
PCI-6871 User’s Manual
50
Step 6. "S3 GraphicsTwister" appears under the adapter tab. Click the
"Apply" button, then the "OK" button.
Step 7. Press “Yes” to reboot.
51
Chapter 5 PCI SVGA Setup
5.2.2 Installation for Windows 98/Me
Step 1. Select "Start", "Settings", "Control Panel", "Display", and "Settings," then press the "Advanced..." button.
PCI-6871 User’s Manual
52
Step 2. Select “Adapter,” then “Change.”
53
Chapter 5 PCI SVGA Setup
Step 3. Press “Next,” then “Display a list....”
Step 4. Press the “Have disk...” button.
PCI-6871 User’s Manual
54
Step 5. Insert the CD into the CD-ROM drive. Type in the path
D:\slotPC\6871\VGA\Win9x_Me
Then press “OK”
D:\slotPC\6871\VGA\Win9x_Me
Step 6. Select the highlighted item, then click “OK.”
55
Chapter 5 PCI SVGA Setup
Step 7. "S3 Graphics Twister"appears under the adapter tab. Click the
"Apply" button.
Step 8. Press “Yes” to reboot.
PCI-6871 User’s Manual
56
5.2.3 Installation for Windows NT
Note:
Service Pack X (X = 3, 4, 5, 6,...) must be
installed first, before you install the Windows
NT VGA driver.
Step 1. Select "Start", "Settings", "Control Panel" and double click the
"Display" icon.
57
Chapter 5 PCI SVGA Setup
Step 2. Choose the "Settings" tab, and press the "Display Type" button.
PCI-6871 User’s Manual
58
Step 3. Press the "Change..." button.
59
Chapter 5 PCI SVGA Setup
Step 4. Click the "Have Disk..." button.
Step 5. Type the path:
D:\slotPC\VGA\WinNT
Press the "OK" button.
D:\slotPC\VGA\WinNT
PCI-6871 User’s Manual
60
Step 6. Select the highlighted item, and click the "OK" button.
Step 7. Press "Yes" to proceed.
Step 8. Press "OK" to reboot.
61
Chapter 5 PCI SVGA Setup
5.2.4 Installation for Windows 2000
Step 1. Select "System", "Settings", "Control Panel" and double click the
"system" icon.
PCI-6871 User’s Manual
62
Step 2. Choose the "Video Controller (VGA Compatible)” button.
63
Chapter 5 PCI SVGA Setup
Step 3. Choose the "Drive" button, press “Update Driver...” button.
PCI-6871 User’s Manual
64
Step 4. Choose "Display a list of..." , then press “Next” button.
Step 5. Choose “Display adapters”, press “Next” button.
65
Chapter 5 PCI SVGA Setup
Step 6. Click the “Have Disk” button.
Step 7. Type the path D:\slotPC\6871\VGA\Win2000 press the “OK”
button.
D:\slotPC\VGA\Win2000
PCI-6871 User’s Manual
66
Step 8. Press “Finish" to reboot.
5.2.5 Installation for Windows XP
Step 1. Select "System", "Settings", "Control Panel" and double click the
"system" icon.
67
Chapter 5 PCI SVGA Setup
Step 2. Choose “Hardware” and “Device Manager”, press “OK” button.
PCI-6871 User’s Manual
68
Step 3. Choose “Video Controller (VGA Compatible), press “OK” button.
69
Chapter 5 PCI SVGA Setup
Step 4. Choose "Driver”, “Update Driver”, press “OK” button.
Step 5. Choose “Install from a list.....” , press “Next”.
PCI-6871 User’s Manual
70
Step 6. Choose “Don’t search. I will....”, press “Next” button.
Step 7. Choose “Display adapters”, press “Next” button.
71
Chapter 5 PCI SVGA Setup
Step 8. Type the path D:\slotPC\6871\VGA\WinXP then press “OK”
button.
D:\slotPC\6871\VGA\Win2000
Step 9. Choose “S3 Graphics Twister + S3 Hotkey” then press “Next”
button.
PCI-6871 User’s Manual
72
Step 10. Press “Finish" to reboot.
5.3 Further Information
For further information about the AGP/VGA installation in your PCI6871, including driver updates, troubleshooting guides and FAQ lists,
visit the following web resources:
VIA website:
www.via.com.tw
manufacturers website: www.emacinc.com
73
Chapter 5 PCI SVGA Setup
PCI-6871 User’s Manual
74
CHAPTER
6
Audio Setup
The PCI-6871 is equipped with an audio
interface that records and plays back
CD-quality audio. This chapter provides
instructions for installing the software drivers
included on the audio driver diskettes.
75
Chapter 6 Audio Setup
Chapter 6 Audio Setup
6.1 Introduction
The PCI-6871 supports AC97 audio through the optional audio module
PCM-231A-00A1.
6.2 DOS utilities
6.2.1 VIA Sound Blaster Pro compatible set up program
Please "Enable" the Sound Blaster setting in the BIOS before playing
Sound Blaster compatible DOS games. To enable the settings in the
BIOS:
INTEGRATED PERIPHERALS -> Onboard Legacy Audio
-> Sound Blaster (Disable -> Enable)
Chipset Feature Setup
->On Chip Sound (Disable-> Enable)
The Sound Blaster Pro compatible sound chip is integrated into the VIA
PCI audio device in order to have Sound Blaster compatible DOS games
running on the system.
If you want to play Sound Blaster compatible DOS games under the real
mode MS-DOS or the "Restart in MS-DOS" from Win9x, then you
should run this setup program to enable OPL3 MIDI music. Otherwise,
the sound effects will be heard, but not the music. If you want to play legacy games in a Windows DOS Box, then you don't need to install this
program.
6.2.2 VIA Sound Blaster Installation
Follow these steps to enable the Sound Blaster Pro compatible functions.
Step 1. Enable the Sound Blaster first on the BIOS setting of the
"Onboard Legacy Audio" and "On-Chip Sound".
Step 2. Run the "Install.exe".
A:> INSTALL
PCI-6871 User’s Manual
76
Step 3. The program will copy the relative files into the directory which
you assign. Next, the program will insert the following new line
into the AUTOEXEC.BAT and copy the original
AUTOEXEC.BAT to AUTOEXEC.VIA.
C: \VIAUDIO\VIAUDIO.COM
Step 4. Reboot the system when the installation is complete.
Step 5. Uninstall by deleting the new line from the AUTOEXEC.BAT.
6.3 Driver installation
6.3.1 Before you begin
Please read the instructions in this chapter carefully before you attempt
installation. The audio drivers for the PCI-6871 board are located on the
audio driver CD. Run the supplied SETUP program to install the drivers;
don’t copy the files manually.
Note:
The files on the software installation diskette
are compressed. Do not attempt to install the
drivers by copying the files manually. You must
use the supplied SETUP program to install the
drivers.
6.3.2 Windows 95/98 drivers
77
Chapter 6 Audio Setup
Step 1. Click "Start" and select "Settings". Click "Control Panel" and
double-click "Add New Hardware".
Step 2. In the Add New Hardware Wizard window, click "Next".
PCI-6871 User’s Manual
78
Step 3. In the following Add New Hardware Wizard window, click
"Next" for Windows to search for Plug and Play devices.
Step 4. In the following Add New Hardware Wizard window, select "No,
the device isn't in the list."and click "Next".
79
Chapter 6 Audio Setup
Step 5. In the following Add New Hardware Wizard window, select "No,
I want to select..." and click "Next".
Step 6. In the following Add New Hardware Wizard window, select
"Sound, video and game controllers" and click "Next".
PCI-6871 User’s Manual
80
Step 7. In the following Add New Hardware Wizard window, click
"Have Disk...".
Step 8. In the Install From Disk window, click "Browse".
81
Chapter 6 Audio Setup
Step 9. In the Open window, select
"D:\slotPC\6871\Audio\98se_Me_2k_xp\WIN95_98.
Step 10. In the Install From Disk window, click" OK".
\6871\Audio\98se_Me_2K_XP\WIN95_98
PCI-6871 User’s Manual
82
Step 11. In the Select Device window, select "VIA PCI Audio Controller
(WDM)" and click "OK".
Step 12. In the Add New Hardware Wizard window, click "Next".
83
Chapter 6 Audio Setup
Step 13. The Copying Files... window will appear.
Step 14. In the Add New Hardware Wizard window, click "Finish". Then
reboot the system.
PCI-6871 User’s Manual
84
6.3.3 Windows NT drivers
Step 1. Click "Start" and select "Settings". Click "Control Panel" and
double-click "Multimedia".
Step 2. In the Multimedia Properties window, select the "Devices" tab.
Then select the "Audio Devices" item, and click "Add...".
85
Chapter 6 Audio Setup
Step 3. In the Add window, select the "Unlisted..." item and click "OK".
Step 4. When the Install Driver window appears, insert the utility disc
into the CD-ROM drive. Type: D:\slotPC\6871\Audio\WinNT\
Then click "OK".
D:\slotPC\6871\Audio\WinNT
PCI-6871 User’s Manual
86
Step 5. In the Add Unlisted or Updated Driver window, select the "VIA
PCI Audio controller" item. Then click "OK".
Step 6. In the System Setting Change window, click "Restart Now".
87
Chapter 6 Audio Setup
6.3.4 Windows 2000 Drivers
Step 1. Select “System”, “Setting”, “Control Panel” and double click
“system” icon.
Step 2. Choose “Multimedia Audio Controller” button.
PCI-6871 User’s Manual
88
Step 3. Choose “Driver button, press “Update Driver” button.
Step 4. Choose “Sound, video and game controllers”, press “Next”
89
Chapter 6 Audio Setup
Step 5. Click the “Have Disk...” button
Step 6. Type the path D:\slotPC\6871\Audio\98se_Me_2k_xp\Win2000
press the “ok” button.
Step 7. Click “Have Disk” button
PCI-6871 User’s Manual
90
Step 8. Press “Next” button
Step 9. Press “Finish” to reboot
91
Chapter 6 Audio Setup
PCI-6871 User’s Manual
92
CHAPTER
7
PCI Bus Ethernet Interface
This chapter provides information on
Ethernet configuration.
• Introduction
• Installation of Ethernet drivers for
Windows 98/2000/NT
• Further information
93
Chapter 7 PCI Bus Ethernet Interface
Chapter 7 PCI Bus Ethernet Interface
7.1 Introduction
The PCI-6871 is equipped with a high performance 32-bit Ethernet
chipset which is fully compliant with IEEE 802.3 100 Mbps CSMA/CD
standards. It is supported by major network operating systems. It is also
both 100Base-T and 10Base-T compatible. The medium type can be configured via the RSET8139.exe program included on the utility disk.
7.2 Installation of Ethernet driver
Before installing the Ethernet driver, note the procedures below. You
must know which operating system you are using in your PCI-6871
Series, and then refer to the corresponding installation flow chart. Then
just follow the steps described in the flow chart. You will quickly and
successfully complete the installation, even if you are not familiar with
instructions for MS-DOS or Windows.
Note:
The windows illustrations in this chapter are
examples only. Follow the steps and pay attention to the instructions which appear on your
screen.
7.2.1 Installation for MS-DOS and Windows 3.1
If you want to set up your Ethernet connection under the MS-DOS or
Windows 3.1 environment, you should first check your server system
model. For example, MS-NT, IBM-LAN server, and so on.
Then choose the correct driver to install in your biscuit PC.
The installation procedures for various servers can be found on the supplied CD-ROM, the correct path being:
D:\slotPC\6871\LAN\8139C\wfw311
PCI-6871 User’s Manual
94
7.2.2 Installation for Windows 98
Step 1.
a. Select "Start", "Settings". "Control Panel".
b. Double click "Network".
Step 2. a. Click "Add" and prepare to install network functions.
95
Chapter 7 PCI Bus Ethernet Interface
Step 3. a. Select the "Adapter" item to add the Ethernet card.
Step 4. a. Click "Have Disk" to install the driver.
Step 5. a. Insert the CD into the D: drive
b. Fill in "D:\slotPC\6871\LAN\”
c. Click "OK"
D:\slotPC\6871\LAN\
PCI-6871 User’s Manual
96
Step 6. a. Choose the "Realtek RTL8139(A/B/C/8130) PCI Fast
Ethernet" item.
b. Click "OK".
Step 7. a. Make sure the configurations of relative items are set correctly.
b. Click "OK" to reboot.
97
Chapter 7 PCI Bus Ethernet Interface
7.2.3 Installation for Windows 2000
Step 1. Open Device Manager,
PCI-6871 User’s Manual
98
Step 2.
99
Chapter 7 PCI Bus Ethernet Interface
Step 3.
Step 4.
PCI-6871 User’s Manual
100
Step 5.
Step 6.
101
Chapter 7 PCI Bus Ethernet Interface
Step 7.
Step 8.
PCI-6871 User’s Manual
102
Step 9.
7.2.4 Installation for Windows NT
Step 1. a. Select "Start", "Settings", "Control Panel"
b. Double click "Network"
Step 2. a. Choose type of network.
103
Chapter 7 PCI Bus Ethernet Interface
b. Click "Next"
Step 3. a. Click "Select from list..."
PCI-6871 User’s Manual
104
Step 4. Click “Have Disk.”
Step 5. a. Insert the Utility CD ROM
b. Fill in the correct path:
D:\slotPC\6871\LAN\8139C\winnt4
c. Click "OK".
D:\slotPC\6871\LAN\8139C\WinNT4
105
Chapter 7 PCI Bus Ethernet Interface
Step 6. Check the highlighted item, and click “OK.”
PCI-6871 User’s Manual
106
7.
Click “Next” to continue setup.
Step 8. Choose the networking protocols, then click "Next"
107
Chapter 7 PCI Bus Ethernet Interface
Step 9. Select the correct Network Services then click "Next"
Step 10. Click “Next” to continue setup.
PCI-6871 User’s Manual
108
11.
Click “Next” to start the network.
7.3 Further information
Realtek website:
www.realtek.com.tw
Intel website:
www.intel.com
Manufacturer's website:
www.emacinc.com
109
Chapter 7 PCI Bus Ethernet Interface
PCI-6871 User’s Manual
110
Appendix
A
Programming the
Watchdog Timer
The PCI-6871 is equipped with
a watchdog timer that resets the CPU or
generates an interrupt if processing comes
to a standstill for any reason. This
feature ensures system reliability in
industrial standalone or unmanned environments.
111
Appx. A
Appendix A Programming the Watchdog
Timer
A.1 Supported Input Timing Modes
In order to program the watchdog timer, you must write a program which
writes I/O port address 443 (hex). The output data is a value of time interval. The value range is from 01 (hex) to 3E (hex), and the related time
interval is 1 sec. to 62 sec.
Data
01
02
03
04
3E
Time Interval
1 sec.
2 sec.
3 sec.
4 sec.
.
.
.
62 sec.
After data entry, your program must refresh the watchdog timer by
rewriting the I/O port 443 (hex) while simultaneously setting it.
When you want to disable the watchdog timer, your program
should read I/O port 443 (hex).
PCI-6871 Users’ Manual
112
The following example shows how you might program the watchdog
timer in BASIC:
10
20
30
40
50
60
70
80
1000
1070
2000
2090
REM Watchdog timer example program
OUT &H443, data REM Start and restart the
watchdog
GOSUB 1000 REM Your application task #1
OUT &H443, data REM Reset the timer
GOSUB 2000 REM Your application task #2
OUT &H443, data REM Reset the timer
X=INP (&H443) REM Disable the watchdog timer
END
REM Subroutine #1, your application task
.
.
.
RETURN
REM Subroutine #2, your application task
.
.
.
RETURN
113
Appx. A
PCI-6871 Users’ Manual
114
Appendix
B
Installing PC/104
Modules
This appendix gives instructions for
installing PC/104 modules.
115
Appx. B
Appendix B Installing PC/104 Modules
B.1 Installing PC/104 Modules
The PCI-6871's PC/104 connectors give you the flexibility to attach PC/
104 modules.
Installing these modules on the PCI-6871 is quick and simple. The following steps show how to mount the PC/104 modules:
1.
Remove the PCI-6871 from your system, paying particular attention to the safety instructions already mentioned above.
2.
Make any jumper or link changes required to the CPU card now.
Once the PC/104 module is mounted, you may have difficulty in
accessing these.
3.
Normal PC/104 modules have male connectors and mount directly
onto the main card. (Refer to the diagram on the following page.)
4.
Mount the PC/104 module onto the CPU card by pressing the module firmly but carefully onto the mounting connectors.
5.
Secure the PC/104 module onto the CPU card using the four
mounting spacers and screws.
PCI-6871 Users’ Manual
116
PC/104
Mounting Support
Male
Female
PCI-6871
Series
PCA-6751
Series
PC/104 module
PC/104
module
Figure B.1: PC/104 module mounting diagram
117
Appx. B
Figure B.2: PC/104 module dimensions (mm) (±0.1)
PCI-6871 Users’ Manual
118
Table B.1: PCI-6871 Series PC/104 connectors (CN16)
Pin
Signal (CN16)
Number
Row A
Row B
Row C
Row D
0
—
—
0V
0V
1
IOCHCHK*
0V
SBHE*
MEMCS16*
2
SD7
RESETDRV
LA23
IOCS16*
3
SD6
+5 V
LA22
IRQ10
4
SD5
IRQ9
LA21
IRQ11
5
SD4
-5 V
LA20
IRQ12
6
SD3
DRQ2
LA19
IRQ15
7
SD2
-12 V
LA18
IRQ14
8
SD1
ENDXFR*
LA17
DACK0*
9
SD0
+12 V
MEMR*
DRQ0
10
IOCHRDY
N/C
MEMW*
DACK5*
11
AEN
SMEMW*
SD8
DRQ5
12
SA19
SMEMR*
SD9
DACK6*
13
SA18
IOW*
SD10
DRQ6
14
SA17
IOR*
SD11
DACK7*
15
SA16
DACK3*
SD12
DRQ7
16
SA15
DRQ3
SD13
+5 V
17
SA14
DACK1*
SD14
MASTER*
18
SA13
DRQ1
SD15
0V
19
SA12
REFRESH*
KEY
0V
20
SA11
SYSCLK
—
—
21
SA10
IRQ7
—
—
119
Appx. B
Table B.1: PCI-6871 Series PC/104 connectors (CN16)
Pin
Signal (CN16)
Number
Row A
Row B
Row C
Row D
22
SA9
IRQ6
—
—
23
SA8
IRQ5
—
—
24
SA7
IRQ4
—
—
25
SA6
IRQ3
—
—
26
SA5
DACK2*
—
—
27
SA4
TC
—
—
28
SA3
BALE
—
—
29
SA2
+5 V
—
—
30
SA1
OSC
—
—
31
SA0
0V
—
—
32
0V
0V
—
—
*active low
PCI-6871 Users’ Manual
120
Appendix
C
Pin Assignments
This appendix contains information of a
detailed or specialized nature. It includes:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
CPU Fan Power Connector
Ethernet 10/100Base-T Connector
Audio Connector
Main Power Connector
Keyboard and PS/2 Mouse Connector
Floppy Drive Connector
IDE (1st and 2nd) HDD Connector
Parallel Port Connector
Power & HDD LED,
Reset Button Connector
USB Connector
Backlight Connector
IR Connector
CRT Display Connector
Flat Panel Connector
Ext. Flat Panel Connector
LCD Signal Mapping
LVDS Interface Connector
COM Port Connector
CompactFlash Card Connector
ATX Power Feature Connector
DIO Connector
LCD back light Connector
EXT_KB Connector
121
Appx. C
Appendix C Pin Assignments
C.1 CPU Fan Power Connector (FAN 1)
Table C.1: CPU Fan Power Connector (FAN 1)
Pin
Signal
1
2
3
Fan speed signal input
Vcc
GND
C.2 Ethernet 10/100Base-T Connector (CN15)
Table C.2: Ethernet 10/100Base-T connector (CN15)
Pin
Signal
1
2
3
4
5
6
7
8
TX+
TXRX+
N/C
N/C
RXN/C
N/C
PCI-6871 User’s Manual
122
C.3 Audio Connector (CN10)
15
13
3
1
16
14
4
2
Table C.3: Audio connector (CN10)
Pin
Signal
Pin
Signal
1
3
5
7
9
+5V
DATA in
GND
DATA out
+5V
2
4
6
8
10
BitCLK
GND
SYNC
ACRST
reserved
123
Appx. C
C.4 Main Power Connector (CN11)
Table C.4: Main Power Connector (CN11)
Pin
Signal
1
2
3
4
5
6
7
+5 V
GND
GND
N/C
N/C
GND
+5 V
PCI-6871 User’s Manual
124
C.5 Keyboard and PS/2 Mouse Connector (CN25)
Table C.5: Keyboard and mouse connector (CN25)
Pin
Signal
1
2
3
4
5
6
KB CLOCK
KB DATA
MS CLOCK
GND
+5V (KB VCC)
MS DATA
125
Appx. C
C.6 Floppy Disk Drive Connector (CN6)
Table C.6: Floppy Disk Drive Connector (CN6)
Pin
Signal
1
GND
3
GND
5
GND
7
GND
9
GND
11
GND
13
GND
14
GND
17
GND
19
GND
21
GND
23
GND
25
GND
27
GND
29
GND
31
GND
33
GND
*low active
PCI-6871 User’s Manual
Pin
Signal
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
DENSITY SELECT*
N/C
DRIVE TYPE
INDEX*
MOTOR O*
DRIVE SELECT 1*
DRIVE SELECT 0*
MOTOR 1*
DIRECTION*
STEP*
WRITE DATA*
WRITE GATE*
TRACK 0*
WRITE PROTECT*
READ DATA*
HEAD SELECT*
DISK CHANGE*
126
C.7 IDE Hard Drive Connector (CN1, CN7)
Table C.7: IDE HDD connector (CN1, CN7)
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
Signal
IDE RESET*
DATA 7
DATA 6
DATA 5
DATA 4
DATA 3
DATA 2
DATA 1
DATA 0
SIGNAL GND
HDD 0
IO WRITE
IO READ
HD READY
HDACK 0*
IRQ14
ADDR 1
ADDR 0
HARD DISK
SELECT 0*
39
IDE ACTIVE*
41
VCC
43
GND
* low active
Pin
Signal
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
GND
DATA 8
DATA 9
DATA 10
DATA 11
DATA 12
DATA 13
DATA 14
DATA 15
N/C
GND
GND
GND
N/C
GND
N/C
N/C
ADDR 2
HARD DISK
SELECT 1*
GND
VCC
N/C
40
42
44
127
Appx. C
C.8 Parallel Port Connector (CN2)
Table C.8: Parallel Port Connector (CN2)
Pin
Signal
1
STROBE*
3
D0
5
D1
7
D2
9
D3
11
D4
13
D5
15
D6
17
D7
19
ACK*
21
BUSY
23
PE
25
SLCT
* low active
PCI-6871 User’s Manual
Pin
Signal
2
4
6
8
10
12
14
16
18
20
22
24
26
AUTOFD*
ERR
INIT*
SLCTINI*
GND
GND
GND
GND
GND
GND
GND
GND
N/C
128
C.9 HDD, PWR LED CON & WDT output (CN13)
Table C.9: HDD, PWR LED CON & WDT output (CN13)
Pin
Signal
1
2
3
4
5
6
WDT output
GND
power LED+ (+5V)
HDD LED +
power LED - (GND)
HDD LED -
C.10 Reset Button Connector (CN8)
Table C.10: Reset Button Connector (CN8)
Pin
Signal
1
2
Reset signal input
GND
129
Appx. C
C.11 USB Connector (CN20, CN28)
Table C.11: USB Connector (CN20, CN28)
Pin
Signal
Pin
Signal
1
3
5
7
9
+5 V
UVUV+
GND
Chassis GND
2
4
6
8
10
+5 V
UVUV+
GND
N/C
C.12 LCD Inverter Backlight Connector (CN27)
Table C.12: LCD Inverter Backlight Connector (CN27)
Pin
Signal
1
2
3
4
5
+12 V
GND
ENABKL
VBR
+5 V
PCI-6871 User’s Manual
130
C.13 IR Connector (CN9)
Table C.13: IR Connector (CN9)
Pin
Signal
1
2
3
4
5
VCC (5 V)
N.C.
RX
GND
TX
C.14 CRT Display Connector (CN12)
5
1
10
6
15
11
Table C.14: CRT Display Connector (CN12)
Pin
Signal
Pin
Signal
1
2
3
4
5
6
7
8
RED
GREEN
BLUE
N/C
GND
GND
GND
GND
9
10
11
12
13
14
15
N/C
GND
N/C
S-DATA
H-SYNC
V-SYNC
S-CLK
131
Appx. C
C.15 Flat Panel Connector (CN18)
Table C.15: Flat Panel Connector (CN18)
Pin
Signal
Pin
Signal
1
3
5
VDDSAFE5 (+5v output)
GND
VDDSAFE3 (+3.3 v
output)
N/C
P0
P2
P4
P6
P8
P10
P12
P14
P16
P18
P20
P22
GND
SHFCLK
M/DE
N/C
2
4
6
VDDSAFE5 (+5v output)
GND
VDDSAFE3 (+3.3 v
output)
GND
P1
P3
P5
P7
P9
P11
P13
P15
P17
P19
P21
P23
GND
FLM
LP
ENAVEE
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Note:
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
The model number of the CN18 socket is
DF13A-40DP-1.25V (Hirose Electric Co., Ltd.)
PCI-6871 User’s Manual
132
C.16 Extended Flat Panel Display Connector (CN17)
Table C.16: Extended Flat Panel Display Connector (CN17)
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
15
17
19
GND
P24
P26
P28
P30
P32
P34
GND
N/C
N/C
2
4
6
8
10
12
14
16
18
20
GND
P25
P27
P29
P31
P33
P35
GND
N/C
N/C
Note:
The model number of the CN17 socket is
DF13A-20DP-1.25V (Hirose Electric Co., Ltd.)
133
Appx. C
C.17 LCD Signal Mapping
Table C.17: LCD Signal Mapping
Pin
Name
16-bit
DSTN
24-bit
DSTN
18-bit
TFT
24-bit
TFT
36-bit
TFT
R00
PD0
LB3
B0
PD1
LB2
B1
R10
B2
R01
PD2
LB1
LB1
PD3
LB0
LB0
B1
B3
R11
UB3
B2
B4
R02
PD4
PD5
B0
UB2
B3
B5
R12
PD6
UB1
UB1
B4
B6
R03
PD7
UB0
UB0
B5
B7
R13
PD8
LG3
G0
R04
G1
R14
PD9
LG2
LG2
PD10
LG1
LG1
G0
G2
R05
PD11
LG0
LG0
G1
G3
R15
UG3
G2
G4
G00
PD12
PD13
UG2
UG2
G3
G5
G10
PD14
UG1
UG1
G4
G6
G01
PD15
UG0
UG0
G5
G7
G11
R0
G02
PD16
LR3
PD17
LR2
LR2
R1
G12
PD18
LR1
LR1
R0
R2
G03
PD19
LR0
LR0
R1
R3
G13
UR3
R2
R4
G04
PD20
PD21
UR2
UR2
R3
R5
G14
PD22
UR1
UR1
R4
R6
G05
PD23
UR0
UR0
R5
R7
G15
PD24
B00
PD25
B10
PD26
B01
PD27
B11
PD28
B02
PD29
B12
PD30
B03
PD31
B13
PD32
B04
PD33
B14
PD34
B05
PD35
B15
PCI-6871 User’s Manual
134
C.18 LVDS Connector (CN21)
Table C.18: LVDS Connector (CN21)
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
15
17
19
GND
TX0+(Channel 1)
TX0-(Channel 1)
TX1+(Channel 1)
TX1-(Channel 1)
TX2+(Channel 1)
TX2-(Channel 1)
TX3+(Channel 1)
TX3-(Channel 1)
VDD (+3.3V)
2
4
6
8
10
12
14
16
18
20
GND
TX0+(Channel 2)
TX0-(Channel 2)
TX1+(Channel 2)
TX1-(Channel 2)
TX2+(Channel 2)
TX2-(Channel 2)
TX3+(Channel 2)
TX3-(Channel 2)
VDD (+3.3V)
135
Appx. C
C.19 COM Port Connector (CN19, CN20)
Table C.19: COM Port Connector (CN19, CN20)
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
RLSD1 (DCD1)
RX1
TX1
DTR1
GND
RLSD2 (DCD2)
RX2
TX2
DTR2
GND
RLSD3 (DCD3)
RX3
TX3
DTR3
GND
RLSD4 (DCD4)
RX4
TX4
DTR4
GND
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
DSR1
RTS1
CTS1
RI1
GND
DSR2
RTS2
CTS2
RI2
NC
DSR3
RTS3
CTS3
RI3
NC
DSR4
RTS4
CTS4
RI4
NC
PCI-6871 User’s Manual
136
C.20 CompactFlash Card Connector (CN28)
Table C.20: CompactFlash Card Connector (CN28)
Pin
Signal
1
GND
3
D04
5
D06
7
*CS0
9
*ATA SEL
11
A08
13
+5 V
15
A05
17
A03
19
A01
21
D00
23
D02
25
*CD2
27
D11
29
D13
31
D15
33
*VS1
35
*IOWR
37
INTRQ
39
*CSEL
41
*RESER
43
*INPACK
45
*DASP
47
D08
49
D10
* low active
137
Pin
Signal
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
D03
D05
D07
A10
A09
A07
A06
A04
A02
A00
D01
-IOCS16
-CD1
D12
D14
-CS1
-IORD
-WE
+5 V
-VS2
IORDY
-REG
-PDIAG
D09
GND
Appx. C
C.21 ATX Power Feature Connector (CN3)
Table C.21: ATX Power Feature Connector (CN3)
Pin
Signal
1
2
3
5VSB (Stand by voltage)
GND
PS. ON#
C.22 LCD Backlight Connector (CN24)
Table C.22: ATX Power Feature Connector (CN24)
Pin
Signal
1
2
3
to VR pin 1
to VR pin 2
to VR pin 3
PCI-6871 User’s Manual
138
C.23 External Keyboard Connector (CN26)
Table C.23: External Keyboard Connector (CN26)
Pin
Signal
1
2
3
4
5
CLK
DATA
NC
GND
+5V
139
Appx. C
PCI-6871 User’s Manual
140
Appendix
D
System Assignments
This appendix contains information of a
detailed nature. It includes:
•
•
•
•
System I/O ports
1st MB memory map
DMA channel assignments
Interrupt assignments
141
Appx. D
Appendix D System Assignments
D.1 System I/O Ports
Table D.1: System I/O ports
Addr. range (Hex)
Device
000-01F
020-021
040-05F
060-06F
070-07F
DMA controller
Interrupt controller 1, master
8254 timer
8042 (keyboard controller)
Real-time clock, non-maskable interrupt (NMI)
mask
DMA page register
Interrupt controller 2
DMA controller
Clear math co-processor
Reset math co-processor
Math co-processor
Fixed disk
Reserved (Game I/O)
Parallel printer port 2 (LPT 3)
Series port 4
Serial port 2
Prototype card
Reserved
Parallel printer port 1 (LPT 2)
SDLC, bisynchronous 2
Bisynchronous 1
Monochrome display and printer adapter (LPT1)
Reserved
Color/graphics monitor adapter
Series port 3
Diskette controller
Serial port 1
080-09F
0A0-0BF
0C0-0DF
0F0
0F1
0F8-0FF
1F0-1F8
200-207
278-27F
2E8-2EF
2F8-2FF
300-31F
360-36F
378-37F
380-38F
3A0-3AF
3B0-3BF
3C0-3CF
3D0-3DF
3E8-3EF
3F0-3F7
3F8-3FF
* PNP audio I/O map range from 220 ~ 250H (16 bytes)
MPU-401 select from 300 ~ 330H (2 bytes)
PCI-6871 User’s Manual
142
D.2 1st MB memory map
Table D.2: 1st MB memory map
Addr. range (Hex)
Device
F0000h - FFFFFh
*CC000h - EFFFFh
C0000h - CBFFFh
B8000h - BFFFFh
B0000h - B7FFFh
A0000h - AFFFFh
00000h - 9FFFFh
System ROM
Unused (reserved for Ethernet ROM)
Expansion ROM (for VGA BIOS)
CGA/EGA/VGA text
Unused
EGA/VGA graphics
Base memory
* If Ethernet boot ROM is disabled (Ethernet ROM occupies about 16 KB)
* E0000 - EFFFF is reserved for BIOS POST
D.3 DMA channel assignments
Table D.3: DMA channel assignments
Channel
Function
0
1
2
3
4
5
6
7
Available
Available (audio)
Floppy disk (8-bit transfer)
Available (parallel port)
Cascade for DMA controller 1
Available
Available
Available
* Audio DMA select 1, 3, or 5
** Parallel port DMA select 1 (LPT2) or 3 (LPT1)
143
Appx. D
D.4 Interrupt assignments
Table D.4: Interrupt assignments
Interrupt#
Interrupt source
IRQ 0
IRQ 1
IRQ 2
IRQ 3
IRQ 4
IRQ 5
IRQ 6
IRQ 7
IRQ 8
IRQ 9
IRQ 10
IRQ 11
IRQ 12
IRQ 13
IRQ 14
IRQ 15
Interval timer
Keyboard
Interrupt from controller 2 (cascade)
COM2
COM1
COM4
FDD
LPT1
RTC
Reserved (audio)
COM3
Reserved for watchdog timer
PS/2 mouse
INT from co-processor
Primary IDE
Secondary IDE for CFC
* Ethernet interface IRQ select: 9, 11, 15
* PNP audio IRQ select: 9, 11, 15
* PNP USB IRQ select: 9, 11, 15
* PNP ACPI IRQ select: 9, 11, 15
PCI-6871 User’s Manual
144
Appendix
E
Optional Extras for the
PCI-6871
145
Appx. E
E.1 Optional USB cable (CN20)
Optional USB cable (2.0mm)
part no.: 1703100260
E.2 ATX Power Control Cable
part no.: 1703200100
E.3 Audio module
Audio module with
Line-in, Line out, mic
PCI-6871 User’s Manual
part no.: PCM-231A-00A1
146
Download PDF

advertising