Canon IP6310D Printer User Manual

Start Here
Series
Photo Printer
Easy Setup Instructions
1
Unpack the Printer
Carefully remove all items from the box.
2
3
Prepare the Printer
1 Remove the shipping tape from the front and back of the
printer.
4
Install the FINE Cartridges
1 Take out the Color FINE Cartridge (CL-41) from its box and remove the protective
Align the Print Head (FINE Cartridge)
1 Open the paper support and pull out the paper output tray.
tape gently.
2 Open (a) the card slot cover first and (b) the front cover next,
Paper support
Pull down and remove the protective material on the right
side.
Electrical contacts
To the FINE Cartridge holder
(a) Card slot cover
Print head nozzles
PIXMA iP6310D Photo Printer
Protective tape
NOTE:
•Do not touch the electrical contacts or print head nozzles on a FINE Cartridge. The
printer may not print out properly if you touch it.
•Do not reattach the protective tape once you have removed it.
•Handle the removed protective tape carefully to avoid getting your hands dirty or
staining surrounding work area.
(b) Front cover
Paper output tray
2 Pinch the paper guide and slide it to the left. Load a few
sheets of blank paper into the auto sheet feeder, then slide
the paper guide toward the left edge of the paper.
Auto sheet feeder
Power Cord
Protective material
2 Insert the Color FINE Cartridge slightly slanted into the left slot (C).
Print side
3 Close the front cover first and the card slot cover next.
4 Plug the power cord into the back of the printer and connect
the other end to a power outlet.
Press the POWER button. The printer will initialize. Wait until
the POWER lamp remains fully lit.
Paper guide
Color FINE Cartridge
(CL-41)
Paper thickness lever
Power cord
3 Push up the Color FINE Cartridge until it clicks into place.
Photo FINE Cartridge
(CL-52)
IMPORTANT: For correct printer operation, make sure the FINE Cartridge is secure in
slots.
NOTE: Ensure that the paper thickness lever is set to the left
position.
3 Ensure that the message requesting head alignment is
displayed on the LCD, select YES using the
press the OK button.
buttons and
NOTE: Do not connect the USB cable at this stage.
5 When the screen appears on the LCD, confirm a language
and then press the OK button.
NOTE:
If the language you want to be displayed is not selected, refer to
"An Unintended Language is Displayed on the LCD" in the Direct
Printing Guide.
•If you leave the printer more than five minutes without using any
button on the operation panel, the LCD goes into sleep mode
automatically. Press the OK button to turn on the LCD again.
•
Documentation and
Software Kit
6
4 Repeat the procedure for the Photo FINE Cartridge (CL-52), inserting it into the
right slot (P).
Open the card slot cover first and the front cover next.
The FINE Cartridge holder automatically moves to the left.
Write down the serial number. You will need this to register
the product.
The pattern is printed. And the print head is aligned
automatically.
IMPORTANT: It takes about four minutes to finish printing.
When automatic print head alignment can not be
executed correctly, the message "HEAD ALIGNMENT
ERROR" is displayed on the LCD. refer to "An Error
Message is Displayed in the LCD" in the Direct Printing
Guide.
FINE Cartridge
holder
5 Close the front cover first and the card slot cover next.
IMPORTANT: Wait until the preparatory operation is complete; this takes about one
to two minutes.
Serial number
iP6310D_ESI_US_V1.indd 1
The message requesting head alignment is displayed on the LCD.
Go to the next step.
Continue with Step 5
on side two.
2006/05/09 9:54:03
5
5
Windows® Printer Driver Installation
Macintosh® Printer Driver Installation
h
tos
n
i
c
Ma
s
ow
d
n
Wi
The screens below refer to Windows XP Service Pack 2
installation. Screens may differ depending on the operating
system you are using.
7 When the Printer Connection screen appears, connect the USB
cable to the computer and the other end to the printer.
1 TURN THE PRINTER OFF.
You hear the operation sound until the printer is turned off.
It may take about 20 seconds.
2 Turn the computer on and start Windows.
7 When the Easy Install screen appears, click Install.
1 Connect the end of the USB cable to the computer, the other to
NOTE:
•Before installing the driver, disable all anti-virus programs
and automatically loading programs.
•For Windows XP or Windows 2000, log on to Windows as a
member of Administrators group before continuing.
IMPORTANT: If you see the Found New Hardware Wizard,
click Cancel. Next, remove the USB cable connected to your
computer. Then proceed from step 3 to install the printer
driver.
NOTE:
•Before installing the driver, disable all anti-virus programs and
automatically loading programs.
•Use Mac®OS X v.10.2.8 to 10.4.x.
•The screens below refer to Mac OS X v.10.4.x installation.
Screens may differ depending on the operating system you are
using.
•Do not remove or insert the USB cable during installation, as this
may result in the computer or printer not operating normally.
the printer.
NOTE: Move the cursor over items to display explanations of
each application bellow.
8 Read the License Agreement, then click Yes. Follow the
on-screen instructions to install the software.
9 Follow the on-screen instructions to register your product.
8 TURN THE PRINTER ON.
10 When the Installation completed successfully screen
appears, click Restart.
IMPORTANT: If you cannot proceed to the next procedure after
two minutes, refer to "Troubleshooting" instructions
in the Quick Start Guide.
If the message asking for your confirmation to restart your
computer appears, click OK.
The system is restarted automatically.
2 Turn on the computer and start Mac OS X.
3 Insert the Setup CD-ROM.
3 Insert the Setup CD-ROM.
The setup program should run automatically.
9 Follow the on-screen instructions to install the remaining
4 When the main menu screen appears, click Easy Install and
software. When the Installation Results screen appears, click
Next.
follow the on-screen instructions.
NOTE:
•If the CD-ROM folder does not open automatically,
double-click the CD-ROM icon on the desktop.
•Log on as an Administrator before continuing.
4 Double-click the Setup icon.
NOTE:
•Select Easy Install in order to install application software,
on-screen manual, utility and printer drivers. Select Custom
Install in order to choose the options you would like to
install.
•To install PhotoRecord or Adobe® RGB (1998), click Custom
Install and follow the instruction on the screen.
•Adobe RGB (1998) cannot be installed in Windows Me and
Windows 98.
5 When the Easy Install screen appears, click Install.
11 After restarting the computer, select Applications from the
Go menu.
Double-click the Utilities folder, and then double-click the
Printer Setup Utility (Print Center when you use Mac OS X
v.10.2.8) icon. Check that your printer name is displayed on
the Printer List. If your printer name is not displayed on the
Printer List, click Add to add the printer.
For details, refer to the Printer Setup Utility Help or Mac
Help.
5 When the Authenticate screen appears, enter your
10 Follow the on-screen instructions to register your product.
If the message asking for your confirmation to restart your
computer appears, click OK.
The system is restarted automatically.
administrator name and password. Click OK.
If you do not know your administrator name or password, click
on the lower-left corner of the screen, then follow the on-screen
instructions.
11 When the Installation completed successfully screen appears,
click Exit.
If Restart is displayed, ensure the Restart the system now
(recommended) check box is selected, then click Restart.
6 When the main menu screen appears, click Easy Install and
follow on-screen instructions.
NOTE: Move the cursor over items to display explanations of
each application below.
6 Read the License Agreement, then click Yes.
Follow the on-screen instructions to install the software.
If the message asking for your confirmation to restart your
computer appears, click OK. The system is restarted automatically.
NOTE: Select Easy Install in order to install application software,
on-screen manual, utility and printer drivers. Select
Custom Install in order to choose the options you would
like to install.
Part no. QT5-0324-V02 ©2006 CANON INC. "Windows" is a trademark of Microsoft Corporation, registered in the United States and other countries. "Macintosh" and "Mac" are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.
"Adobe" and "Adobe RGB(1998)"are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. Specifications subject to change without notice. Printed in Thailand.
iP6310D_ESI_US_V1.indd 2
2006/05/09 9:54:08