SMLP4-4 Single-mode/Multimode Test Kit with Wave ID and Set Reference

SMLP4-4 Single-mode/Multimode Test Kit with Wave ID and Set Reference
SMLP4-4 Single-mode/Multimode Test
Kit with Wave ID and Set Reference
The SMLP4-4 test kit combines the OPM4-2D optical power meter and OLS4 integrated
LED and LASER light source and is ideally suited for testing fiber optic networks with
hybrid (single-mode and multimode) cables.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Dual or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Large LCD with backlight (OPM4-2D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Low battery indicator
•• Long battery life with 2 x AA alkaline
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T traceable
The OLS4 features 850/1300 nm LED output from a multimode output port and
1310/1550 nm LASER output from a single-mode output port. Each wavelength may be
transmitted individually at CW or with user selectable modulated Tone (SM output). Also,
each wavelength may be transmitted with Wave ID. When transmitting with Wave ID, the
OLS4 supports transmitting pairs of wavelengths in an alternating pattern. Associated with
each operating condition, the designated LED indicator will illuminate to identify the currently enabled operating mode and emitted wavelength(s) along with battery charge status
and external power presence. Both output ports are equipped with UCI based removable
adapters to allow the output connectors to be inspected and cleaned.
The OPM4-2D features automatic wavelength identification and switching (Wave ID)
when used with the OLS4, multiple test Tone detection for fiber identification, and stores
optical references for each calibrated wavelength. A large dual-wavelength LCD display
with backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated
wavelengths [nm], tone signal [Hz], wavelength ID, and estimated remaining battery life.
The OPM4-2D optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements.
The OPM4-2D and OLS4 offer long battery life from common AA alkaline batteries.
The SMLP4-4 test kit is fully N.I.S.T. traceable.
Applications
•• Certify multimode and single-mode links per TIA/EIA standards
•• Fiber identification prior to splicing
Ordering Information
Model
Includes
SMLP4-4
OLS4 optical light source, OPM4-2D optical power meter, AA batteries, protective rubber boots,
adapter cap, 50 and 62.5 µm mandrels, SMLP4-4 test kit user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications.
continued on the next page
Test & Inspection
© 2002-2007, AFL Telecommunications, all rights reserved. SMLP-44-2000 Revision C, 12.20.07
Specifications are subject to change without notice.
1
SMLP4-4 Single-mode/Multimode Test Kit with Wave ID and
Set Reference
OLS4 Light Source specifications
Optical
Wavelength
Emitter type
MM Optical Port
850 ± 30 nm 1300 -10/+50 nm
LED, Class I (IEC 60825 - 1)
Spectral width
Output power
Output Stability
40 nm (typ)
120 nm (typ)
> - 20 dBm, 62.5 µm multimode*
± 0.1 dB over 8 hours
(after 5 min. warm-up)
General
Power
SM Optical Port
1310 ± 20 nm
1550 ± 20 nm
Laser, Class I (FDA 21 CFR 1040.10 and
1040.11, and IEC 60825-1)
5 nm (max)
5 nm (max)
0 dBm, 9 µm single-mode
± 0.05 dB over 1 hour (after 15 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
2 x AA batteries, optional AC adapter
Battery life
Typical 30 hours, minimum 20 hours
Typical 72 hours, minimum 40 hours
Available adapters
SC FC, ST, LC
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Output power will be approximately 3 dB less if a 50 µm mandrel-wrapped jumper is used
instead of a 62.5 µm mandrel-wrapped jumper.
All specifications at 25°C.
OPM4-2D specifications
Optical
OPM4-2D
Calibrated wavelengths
850, 1300,1310, 1550 nm
Detector type
Germanium (Ge)
Measurement range
+6 to -60 dBm
Tone detect range
Wavelength ID range
Accuracy*
+6 to -50 dBm
+6 to -45 for 850 nm
+6 to -50 dBm
+6 to -45 dBm for 850 nm
± 0.25 dB
Resolution
0.01 dB
Measurement units
General
Power
dB, dBm, μW
2 x AA batteries
Battery life
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
Test & Inspection
© 2002-2007, AFL Telecommunications, all rights reserved. SMLP-44-2000 Revision C, 12.20.07
Specifications are subject to change without notice.
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement