Canon LBP-2510 Printer User Manual

Laser Beam Printer
User's Guide
Table of Contents
Power ON / OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Turning the Power ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Turning the Power OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Online and Offline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Online . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Offline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Printable Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Printable Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Paper that Cannot Be Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Printing from the Paper Cassette. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Loading standard size paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Loading Paper in the Multi Purpose Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading Paper (other than envelopes). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading Postcards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading Envelopes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
26
30
33
When a Paper Jam Occurs (Clearing Paper Jams) . . . . . . . . . . . . . . . . . . . . . 38
Procedure for Clearing Paper Jammed in the Printer . . . . . . . . . . . . . . . . . . . 38
Replacing the Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
When <X トナー チェック / コウカン > is Displayed . . . . . . . . . . . . . . . . . . 52
Replacing the Cartridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Canceling Printing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Checking Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Status Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
When a Message Is Displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
When <nn-nn サービス コール > or <F9-nn チェック プリンタ >
Is Displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Table of Contents
1
Power ON / OFF
Turning the printer's power on and off is performed with the power switch on the
right side of the printer. Please learn the correct procedures to avoid any
unexpected trouble.
.
Turning the Power ON
To use the printer, turn it by pressing the power switch to the "I" position. The
machine will be capable of printing after the status of the machine and options are
checked.
IMPORTANT
• Do not turn the power ON right after turning it OFF. After turning it OFF, leave it OFF for 3
seconds or longer before turning it ON again.
• If the printer does not operate properly or an error message appears, see "When a
Message Is Displayed," on p. 69.
.
1
2
Press the "I" side of the power switch and turn the printer ON.
Power ON / OFF
The indicators and display on the control panel will illuminate, and the printer will
perform a self-diagnosis to check the status of the printer and options.
If the results of the self-diagnosis are normal, the オンライン indicator, 印刷可
indicator, and the paper source indicator will illuminate, and <00 LIPS> will
appear indicating that the printer is ready to print.
オンライン
ジョブ
ジョブキャンセル
給紙選択
00 LIPS
A4
ユーティリティ
セットアップ
実行
印刷可
メッセージ
ジョブ
リセット
The following information will appear on the display.
Paper size in the selected
paper source
Ready to print
but no print data
00 LIPS
A4
.
Turning the Power OFF
Turn off the machines in the following procedure.
IMPORTANT
• If the printer is connected to a network, make sure that a print job is not being performed
from a different computer before turning OFF the power.
• If the power is turned OFF with the ジョブ indicator ON, print data remaining in printer
memory will be erased. For necessary print data, wait until the current job is output, or
press [リセット ] and select <ハイシュツ > in offline then print the necessary data and turn
the power OFF.
• Do not turn OFF the power when the printer is in the following status.
- While printing.
- Performing a self-diagnosis right after the power is turned ON.
- When <NVRAM 初期化中 > or <NVRAM 書き込み中 > is indicated in the display.
- When <02 キドウ チュウ > or <02 キャリブレーションチュウ > is indicated in the
displayed.
.
1
Make sure that the ジョブ indicator is off.
オンライン
ジョブ
ジョブキャンセル
給紙選択
00 LIPS
A4
ユーティリティ
セットアップ
実行
印刷可
メッセージ
ジョブ
リセット
Power ON / OFF
3
2
4
Press the "O" side of the power switch and turn the printer
OFF.
Power ON / OFF
Online and Offline
" オンライン " is when the printer is capable of receiving data from a computer.
" オフライン " is when connection with a computer is shut down and data cannot be
received. Specify the printer to offline before operating a menu on the control panel.
.
Online
The printer must be online in order to print from computer operation. Confirm that
the printer is online before copying or printing. If not, bring the printer online in the
following procedure. The printer automatically comes online when it is turned ON.
.
1
Press [ オンライン ].
The オンライン indicator will illuminate and the printer will be ready to print.
IMPORTANT
• If an error is occurring in the printer (when the message indicator is on or message
numbers are blinking) the printer will not become online. The error must be release in
order to become online.
• Be sure not to open a cover or remove a paper cassette on the printer while printing. The
printer may stop and disable the print job.
NOTE
However, if the printer is in the power saver mode, the オンライン indicator will go off even
in online, and only the ready indicator will illuminate.
.
Offline
The printer must be offline in order to operate a menu from the control panel on the
printer, select paper feed methods, or specify a paper size. Bring the printer offline
in the following procedure in order to use the control panel key.
.
1
Press [ オンライン ].
The オンライン indicator will go off and items can be specified from the control
panel.
Online and Offline
5
IMPORTANT
• If printing is attempted from computer operation with the printer in offline, a message
such as < プリンタの準備ができていません > or < プリンタが接続されていません > will
appear.
• This printer will shift to online automatically if left at offline for 5 minutes. The printer
cannot become online automatically if an error is occurring in the printer (when the
message indicator is on or message numbers are blinking) or during operations such as
selecting a menu function/paper feed method or specifying a paper size.
6
Online and Offline
Paper
Use only paper that is appropriate for obtaining the best machine performance.
Using inappropriate paper can lead to deterioration in print quality or paper jams.
.
Printable Paper
The printer can use the following types of paper. indicates that one-sided and
two-sided print can be performed,
indicates that only one-sided print can be
performed, and
indicates that the paper cannot be used.
IMPORTANT
• Load all size paper in the portrait (vertically) orientation.
• If paper in width of 200 mm or less is printed continuously, the safety function to prevent
damages caused by heat, etc. will activate, and the print speed may decrease in few
stages. (It may decrease as low as to approx. 3 ppm.)
Paper
7
Paper source
Paper type
Multi purpose tray
Cassette 1
Plain paper (64~105 g/m2)
Letter
Executive
Legal
A5
B5
A4
Custom size *1
Heavy paper (106~135 g/m2)
Letter
Executive
Legal
A5
B5
A4
Custom size *2
Transparencies A4
Label paper A4
Postcard (100 mm × 148 mm)
Stamped, self-addressed
postcard (148 mm × 200 mm)
Envelop
Youkei No.4
(105 mm × 235 mm)
Youkei No.2
(114 mm × 162 mm)
1
* Plain paper in the following sizes can be loaded.
Multi purpose tray : 76.2 - 216.0 mm in width,
127.0 - 356.0mm in length
Cassette 1 : 148.5 mm or 182.0 - 216.0 mm in width,
210.0 - 356.0mm in length
* 2 Heavy paper in width of 148.5 mm or 182.0 - 216.0 mm in width,
and length of 210.0 - 356.0 mm can be loaded.
■ Abbreviation of Paper Size
The following abbreviations are used to indicate the paper size in paper cassettes.
Paper size
Legal
LGL
Letter
LTR
Executive
8
Paper guide of the paper cassette
Paper
EXEC
Paper Capacity in Paper Sources
Paper source
Paper type
Multi purpose tray
Cassette 1
Approx.500 sheet*
Plain paper (64 g/m2)
Approx.100 sheet
Heavy paper (135 g/m2)
Approx.50 sheet
Transparencies
Approx.50 sheet
Label paper
Approx.40 sheet
Postcard
Approx.50 sheet
Stamped, self-addressed postcard
Approx.50 sheet
Envelope
Approx.10 sheet
* Plain paper (64 g/m2) in the following sizes can be loaded up to half the amount of the maximum capacity 16 mm
below the loading limit mark).
- A5
- Custom size paper in width of 148.5 mm
Paper Capacity of the Output Tray
Paper type
Capacity
g/m2)
Approx.250 sheet
Plain paper (64
Heavy paper (135 g/m2)
Approx.100 sheet
Transparencies
Approx.50 sheet
Label paper
Approx.50 sheet
Postcard
Approx.50 sheet
Stamped, self-addressed postcard
Approx.50 sheet
Envelope
Approx.10 sheet
■ Plain Paper
• Plain paper in width of 76.2 - 216.0 mm, length of 127.0 - 356.0 mm, and weight of
64 - 105 g/m2 including standard paper sizes such as Legal, Letter, Executive, A4, B5,
and A5 can be used.
Plain paper can be fed from both the paper cassette and multi purpose tray. Automatic
2-sided print can be performed only with standard paper sizes other than A5.
■ Heavy Paper
• Heavy paper in width of 76.2 - 216.0 mm, length of 127.0 - 356.0 mm, and weight of 106
- 135 g/m2 including standard paper sizes such as Legal, Letter, Executive, A4, B5, and
A5 can be used. Heavy paper is fed from the multi purpose tray and only one-sided print
can be performed.
Paper
9
■ Transparencies
Use Canon Color Laser OHP film, TR-3 A4 (A4-size) with this printer.
IMPORTANT
• OHP film TR-3 A4 is designed for use with LBP-2160 / 2040 / 2050 / 2200 / 2260 /
2260PS / 2260PSII / 2300 / 2510 / 2360 / 2710 / 2810. Never use it for other color laser
printers or monochrome printers as this may cause a malfunction or a deterioration in
print quality.
• Do not use transparencies not designed for this printer, such as transparencies for
LBP-2030 (Canon Color Laser OHP film T-H1 A4, T-H1 LTR), transparencies for CLC, or
transparencies for monochrome printers (Transparency for Canon domestic LBP). This
may cause a malfunction in the fixing unit inside the printer or a deterioration in print
quality.
■ Label Sheets
Label sheets in size of A4 can be used with this printer. Check the front and back sides of
the label sheets and load the sheets so that the front side is facing down in the multi
purpose tray.
IMPORTANT
Do not use the following label sheets. If label sheets that do not conform to the printer
specifications are used, it may result in hard-to-clear paper jams or printer malfunctions.
- Sheets with labels likely to peel off, or sheets with some labels already used.
- Coated sheets that can easily peel off from the backing sheet.
- Label sheets with exposed adhesive.
■ Postcard/Stamped, self-addressed postcard
Official postcards and official stamped, self-addressed postcards can be only used. Load
postcards and self-addressed postcards with the print side face down.
IMPORTANT
• Do not use postcards and stamped, self-addressed postcards other than official
postcards and official stamped, self-addressed postcards. This may caused a
deterioration in print quality as well as paper jams.
• You can use only stamped self-addressed postcards without creases.
• If the edges of postcards are curled, bend them back in the opposite direction to
straighten them before loading them in the multi purpose tray.
• Do not use postcards or stamped self-addressed postcards for inkjet printer.
10
Paper
■ Envelopes
Envelopes that can be used with this printer are Youkei No.4 and Youkei No.2 with the
following structure. Place the envelopes with the side subject to printing the name and
address facing down in the multi purpose tray.
Youkei No.4(105mm×235mm )
Youkei No.2(114mm×162mm)
Envelope Y401 Canon
for LBP/recommended
Envelope Y201 Canon
for LBP/recommended
* Envelopes with a flap on the short edge cannot be used.
IMPORTANT
• Do not use the following envelopes. If envelopes that do not conform to the printer
specifications are used, it may result in hard-to-clear paper jams or printer malfunctions.
- Envelopes with fasteners or snaps.
- Envelopes with windows.
- Self-adhesive envelopes.
- Envelopes with wrinkles or creases.
- Envelopes with very irregular thickness at the folds or overlaps.
- Envelopes in irregular shapes (Non-rectangular).
• Press the envelopes with your hands to eliminate air, then press down on the edges
before loading them in the multi purpose tray.
• Do not print on the back (with adhesive surface) of envelopes.
NOTE
When printing on envelopes, images printed on the flap or adhesive surface on the back
of the envelope may blur or the trailing edge may come out dirty.
Paper
11
.
Printable Area
The areas of paper shown below can be printed with this printer.
■ Plain paper / heavy paper / transparencies / label sheets
Data cannot be printed inside the 5mm-border around the paper.
5 mm
5 mm
5 mm
5 mm
■ Postcard/Stamped, self-addressed postcard
Data cannot be printed inside the 5 mm-border around the postcard or stamped,
self-addressed postcard.
100 mm
200 mm
5 mm
123-4567
東京都千代田区
○○○
5 mm
12
Paper
5 mm
123-4567
148 mm
5 mm
5 mm
東京都千代田区
○○○
5 mm
148 mm
5 mm
5 mm
■ Envelopes
Data cannot be printed inside the 10 mm-border around the envelope.
Adjust the location for printing according to your needs.
(Sample: Youkei No.4 envelope)
10 mm
235 mm
123-4567
105 mm
10 mm
10 mm
東京都千代田区
○○○
10 mm
.
Paper that Cannot Be Used
To prevent malfunctions such as paper jams or printer malfunctions, do not use
paper indicated below.
IMPORTANT
• Paper that tends to cause paper jams.
- Paper that is too thick or thin.
- Paper that is shaped irregularly.
- Paper that is damp or wet.
- Paper that is torn.
- Paper that is rough or extremely smooth.
- Paper with perforations.
- Paper that is curled or paper with creases.
- Paper with special coating on its surface (coated paper for ink jet printers, etc.).
- Labels sheets in which the base peels easily.
- Paper that has been printed or copied on one side by a copier or a different laser printer
(the non-printed side is also disabled).
- Paper that has fins.
- Paper that is wrinkled.
- Paper that is folded at corners.
• Paper in which the quality changes at high temperature.
- Paper printed with ink that is capable of melting, burning, dissolving, or generating
poisonous gas from the heat of the fixing unit (approx. 320 °F(160 °C)).
- Heat-sensitive paper.
- Paper with a processed surface that is used for color printing.
- Paper with special coating on its surface (coated paper for ink jet printers, etc.).
- Paper with adhesive on its surface.
Paper
13
• Paper that may damage the printer.
- Carbon paper.
- Paper with staples, clips, ribbons, or tapes.
- Paper that has been printed or copied on one side by a copier or a different laser printer
(the non-printed side is also disabled).
• Paper that is difficult for toner to adhere to.
- Paper with rough surfaces such as rough paper or Japanese paper.
- Paper with special coating on its surface (coated paper for ink jet printers, etc.).
- Paper containing thick fibers.
14
Paper
Printing from the Paper Cassette
Follow the procedure described below to load paper into the paper cassette.
IMPORTANT
• Be sure to follow the instructions below to prevent paper jams.
- Do not load paper other than plain paper (64-105 g/m2) such as transparencies, label
sheets, or envelopes. For details on paper that can be loaded, see "Paper," on p. 7.
- Do not use paper that has fins, or paper that is wrinkled or extremely curled.
- Load paper in the cassette when paper runs out. If the paper is loaded with paper still
remaining in the cassette, it may result in misfeeds.
- Approximately 500 sheets of plain paper (64 g/m2) can be loaded in the paper cassette
(excluding A5 or custom size paper in width of 148.5 mm. Be sure not to exceed the
loading limit mark. If the loading limit mark is exceeded, it may result in misfeeds.
- Paper in size of A5 or custom size paper in width of 148.5 mm can be loaded up to half
the amount 16 mm of the maximum capacity (500 sheets) below the loading limit mark)
as shown in the figure. Exceeding this limit may result in misfeeds.
Loading
limit mark
More than
16 mm
Printing from the Paper Cassette
15
- Do not touch the paper feed roller or black rubber part of the paper cassette. This
caused a paper feed failure.
Loading standard size paper
When loading paper in size of Legal, Letter, Executive, A4, B5, or A5 in the paper
cassette, follow the procedure described below.
1
16
If the multi purpose tray was being used, remove any paper
remaining in the tray and close the tray.
Printing from the Paper Cassette
2
Pull out the paper cassette.
Hold the handle on the front of the cassette to pull it out half way, then support it
with both hands as shown in the figure below to pull it all the way out.
CAUTION
When loading paper in the cassette, be sure that the cassette is removed
from the printer. If paper is loaded when the cassette is pulled just partially
out of the printer, the cassette may drop or the printer may overbalance
and result in personal injuries.
IMPORTANT
• The paper cassette is heavy, so hold it securely with both hands.
• Place the paper cassette on a sturdy, flat surface.
Printing from the Paper Cassette
17
3
Push the plate to lock it.
CAUTION
If the plate is locked, do not touch the white lock release lever located on
the right side of the paper cassette. The plate may snap by force if the lock
is release and result in personal injuries.
Lock release lever
18
Printing from the Paper Cassette
4
Set the Standard / Custom selection switch to "STANDARD."
M
STO
CU
ND
STA
D
AR
IMPORTANT
Be sure to set the Standard / Custom selection switch to "STANDARD" in order to
use standard size paper.
5
Grasp the lock release lever of the rear paper guide and slide
it to the mark indicating the subject paper size.
When loading Legal size paper, slide the rear paper guide to the rear until it
stops.
L
LG
4
A
R
LT
IS
J
5
B
C
E
X
E
5
A
IMPORTANT
Be sure to check that the paper guide is adjusted to the position of the paper you
want to load. If the paper guide is not adjusted to the proper paper size position, it
may result in misfeeds.
Printing from the Paper Cassette
19
6
Grasp the lock release lever on the right side of the paper
guide and slide it to the mark indicating the subject paper
size.
The left paper guide operates simultaneously with the right paper guide.
A5
B5
JIS
EX
EC
A4
LGLTR
L
IMPORTANT
Be sure to check that the paper guide is adjusted to the position of the paper you
want to load. If the paper guide is not adjusted to the proper paper size position, it
may result in misfeeds.
7
Adjust the trailing edge of the paper stack against the rear
paper guide and load the paper stack into the cassette.
CAUTION
Handle paper with caution and take care not to cut your hand on the edges
of the paper.
20
Printing from the Paper Cassette
IMPORTANT
Double-feeding may occur frequently if the edges of the stacked paper are not
aligned properly. In such a case, align the paper stack on the flat surface before
loading it.
NOTE
To print on letterhead paper or paper printed with a logo, load the paper so that the
front side of the paper (print side) is facing up and the upper edge comes toward
you.
:Paper feed
direction
Printing from the Paper Cassette
21
8
Press down on the stack of paper as shown in the figure,
confirm that the loading limit mark is not exceeded, then load
the stack of paper under the paper holders and hooks of the
paper guide.
Paper holder
Loading
limit mark
Hooks
Loading
limit mark
Paper holder
IMPORTANT
• Approximately 500 sheets of plain paper (64 g/m2) can be loaded in the paper
cassette (excluding A5 paper). Be sure not to exceed the loading limit mark. If the
loading limit mark is exceeded, it may result in misfeeds.
22
Printing from the Paper Cassette
• Paper in size of A5 can be loaded up to half the amount (16 mm of the maximum
capacity (500 sheets) below the loading limit mark) as shown in the figure.
Exceeding this limit may result in misfeeds.
Loading
limit mark
More than
16 mm
9
Insert the paper size indication plate into the plate slot located
in the left front side of the paper cassette.
Indicate the paper size loaded in the cassette on the bottom.
Printing from the Paper Cassette
23
10 Attach the paper cassette to the printer.
Hold the cassette securely with both hands and push it into the printer firmly until
the front side of the cassette is flush with front surface of the printer.
If the printer is ON when the cassette is attached, you will hear the sound of
printer operation. If a message indicating that paper runs out, the print job will
resume automatically.
CAUTION
Be careful to avoid catching your fingers when inserting the paper
cassette into the printer.
IMPORTANT
If you have trouble attaching the paper cassette to the printer, do not try to push it
in forcefully. Remove the cassette once, adjust it straight and re-insert it into the
printer.
24
Printing from the Paper Cassette
● Indication of the amount of paper remaining in the cassette
The paper cassette is supported with an indicator that shows the amount of
paper remaining in the cassette. If the cassette is full, the indicator will be at
the top. The indicator will go down as the amount of paper decreases,
therefore, you can acknowledge the amount of paper remaining in the cassette.
Remaining paper
indicator
When a large amount
is remaining
When a small amount
is remaining
Printing from the Paper Cassette
25
Loading Paper in the Multi Purpose Tray
Loading Paper (other than envelopes)
Load plain paper, heavy paper, or label sheets into the multi purpose tray in the
following procedure.
IMPORTANT
Data cannot be printed in the 5 mm border around the paper.
.
1
Open the multi purpose tray.
Grasp the handle in the mid-section of the printer to open the multi purpose tray.
IMPORTANT
• Make sure that there are no obstacles in front of the printer before opening the
multi purpose tray.
• Do not place anything other than the print media in the multi purpose tray.
Furthermore, avoid pressing or applying excessive force. It may result in damaging
the tray.
26
Loading Paper in the Multi Purpose Tray
● Closing the multi purpose tray
❑ Remove any paper left in the multi purpose tray before closing the tray.
Keep the multi purpose tray closed when it is not being used.
2
3
Specify the width of the slide guides slightly wider than the
paper width.
When loading transparencies or label sheets, fan a small
amount of the media at a time and align the edges.
Fan a few amount at a time.
Align the edge by tapping the
stack on a flat surface.
Loading Paper in the Multi Purpose Tray
27
CAUTION
Handle paper with caution and take care not to cut your hand on the edges
of the paper.
IMPORTANT
• Be sure that transparencies and label sheets are fanned thoroughly. If they are not
fanned thoroughly, they may overlap when fed into the printer and result in paper
jams.
• When fanning or aligning transparencies, try to hold the edges and avoid touching
the print surface.
• Be careful not to mark/stain the print surface of transparencies with fingerprints,
dust, or oil. It may deteriorate the print quality.
4
Load paper gently as far as it will go into the printer with the
print side facing down.
Loading
limit mark
CAUTION
Handle paper with caution and take care not to cut your hand on the edges
of the paper.
IMPORTANT
• Up to 100 sheets of plain paper (64 g/m2) can be loaded in the multi purpose tray.
Be sure that the height of the paper stack does not exceed the loading limit mark.
• Do not load paper at an angle.
• If the trailing edge of the paper stack is not properly aligned, it may result in
misfeeds or paper jams.
• If the leading edge of the paper stack is folded or curled, straighten the paper
before loading the stack.
28
Loading Paper in the Multi Purpose Tray
• Double-feeding may occur frequently if the edges of the stacked paper are not
aligned properly. In such a case, align the edges of the stack on a hard, flat surface.
NOTE
• To print on letterhead paper or paper printed with a logo, load paper so that the
front side of the paper (print side) is facing down and the top of the paper goes into
the far end of the tray.
:Paper feed
direction
5
Move the slide guides so that they closely fit against both
edges of the paper.
Loading Paper in the Multi Purpose Tray
29
IMPORTANT
• Be sure to adjust the slide guides to the width of the paper. If there is too much
space between the paper stack and slide guides, or if the slide guides are set too
tightly against the paper stack, it may result in misfeeds or paper jams.
• Do not touch or remove paper from the tray while printing. It may result in a printer
malfunction.
Loading Postcards
Official postcards and official stamped, self-addressed postcards can be loaded
into the multi purpose tray. To load postcards into the multi purpous tray, follow the
procedure discribed below.
IMPORTANT
• Data cannot be printed in a 5 mm wide border around the postcard.
• You can use only stamped self-addressed postcard without creases.
1
Open the multi purpose tray.
Grasp the handle in the mid-section of the printer to open the multi purpose tray.
30
Loading Paper in the Multi Purpose Tray
IMPORTANT
• Make sure that there are no obstacles in front of the printer before opening the
multi purpose tray.
• Do not place anything other than the print media in the multi purpose tray.
Furthermore, avoid pressing or applying excessive force. It may result in damaging
the tray.
2
3
Specify the width of the slide guides slightly wider than the
paper width.
Load the stack of postcards into the multi purpose tray.
Load postcards with the print side face down and the top edge of the postcards
going into the printer first.
Loading
limit mark
CAUTION
• Handle paper with caution and be careful not to cut your hand with the
edge of the paper.
IMPORTANT
• Approximately 50 Sheets of postcard can be loaded in the multi purpose tray. Be
sure that the height of the postcard stack does not exceed the loading limit mark.
Loading Paper in the Multi Purpose Tray
31
• If the postcards are warped, corret warp so that it does not exceed 2 mm in an
upward direction before loading them into the tray.
No more than 2 mm
• When you print on a stamped self-addressed postcard, make sure that the
application page setup and orientation settings mutch the way the postcard is
loaded in the multi purpose tray. (Example: For Windows NT 4.0/2000/XP, select
[ 往復はがき横 ])
• Double-feeding may occur frequently if the edges of the stacked postcard are not
aligned properly. In such case, align the edges of the stack on a hand, flat surface.
32
Loading Paper in the Multi Purpose Tray
4
Move the slide guide so that they closely fit against both
edges of the postcard.
IMPORTANT
• Be sure to adjust the slide guide to the width of the postcard.
If there is too much space between the postcard stack and slide guide, or if the
slide guide is set too tightly against the postcard stack, it may result in misfeeds or
paper jam.
• Do not touch or remove the postcards from the tray while printing. It may result in a
printer malfanction.
Loading Envelopes
Envelopes can be printed from the multi purpose tray. Load envelopes in the
following procedure.
Youkei No.4(105mm×235mm )
Youkei No.2(114mm×162mm)
Envelope Y401 Canon
for LBP/recommended
Envelope Y201 Canon
for LBP/recommended
* Envelopes with a flap on the short edge cannot be used.
IMPORTANT
• Do not use self-adhesive envelopes. It may result in deterioration in print quality or printer
malfunction.
• When printing on envelopes, data cannot be printed in the 10mm border around the
envelopes.
NOTE
When printing on envelopes, images printed on the flap or adhesive surface on the back
of the envelope may blur or the trailing edge may come out dirty.
Loading Paper in the Multi Purpose Tray
33
.
1
Open the multi purpose tray.
Grasp the handle in the mid-section of the printer to open the multi purpose tray.
IMPORTANT
• Make sure that there are no obstacles in front of the printer before opening the
multi purpose tray.
• Do not place anything other than the print media on the multi purpose tray.
Furthermore, avoid pressing or applying excessive force. It may result in damaging
the tray.
2
34
Specify the width of the slide guides slightly wider than the
paper width.
Loading Paper in the Multi Purpose Tray
3
Place the stack of envelopes on a flat surface, press them with
your hands to eliminate any air pockets, and press down the
corners to crease and flatten the envelopes.
CAUTION
Handle envelopes with caution and take care not to cut your hand on the
edges of the envelopes.
4
Flex the corners of the envelope to remove stiffness and
correct any curled portions.
Loading Paper in the Multi Purpose Tray
35
5
6
Align the edges of the envelopes on a flat surface.
Load the stack of envelopes gently as far as it will go into the
printer, with the side to print the address facing down.
Loading
limit mark
IMPORTANT
• Approximately 10 envelopes can be loaded in the multi purpose tray. Be sure that
the height of the envelope stack does not exceed the loading limit mark.
• The back side (with adhesive surface) of an envelope cannot be printed.
• Load the envelopes so that the flap comes to the right.
36
Loading Paper in the Multi Purpose Tray
7
Move the slide guides so that they closely fit against both
edges of the envelopes.
IMPORTANT
• Be sure to adjust the slide guides to the width of the envelope. If there is too much
space between the paper stack and slide guides, or if the slide guides are set too
tightly against the paper stack, it may result in misfeeds or paper jams.
• Do not touch or remove the envelopes from the tray while printing. It may cause a
printer malfunction.
Loading Paper in the Multi Purpose Tray
37
When a Paper Jam Occurs (Clearing Paper Jams)
When a paper jam occurs in the printer, an alarm will sound. Then the error
message <13 ヨウシガツマリマシタ > will appear on the upper part of the display,
and a message indicating the location of the paper jam, such as <キュウシ エリア>
or < ハイシ エリア >, will appear on the bottom of the display.
When a paper jam occurs, confirm the messages and remove the jammed paper in
the following procedure. If the message still remains after removing the jammed
paper according to the prescribed procedure, torn pieces of the jammed paper may
still be remaining in the machine. In such a case, remove any jammed paper
completely.
.
Procedure for Clearing Paper Jammed in the Printer
When a paper jam occurs in the printer, confirm the displayed message first, then
remove the jammed paper in the following procedure.
WARNING
There are some areas inside the machine which are subject to high-voltages.
When removing jammed paper or when inspecting the inside of the machine, do
not allow necklaces, bracelets, or other metal objects to touch the inside of the
machine, as this may result in burns or electrical shock.
CAUTION
• The fixing unit and its surroundings inside the machine may become hot during
use. When removing jammed paper or when inspecting the inside of the
machine, do not touch the fixing unit and its surroundings, as doing so may
result in burns or electrical shock.
38
When a Paper Jam Occurs (Clearing Paper Jams)
• When removing jammed paper, take care not to allow the toner to come into
contact with your hands or clothing, as this will dirty your hands or clothing. If
they become dirty, wash them immediately with cold water. Washing with warm
water will set the toner and make it impossible to remove the toner stains.
• When removing paper which has become jammed inside the machine, remove
the jammed paper gently to prevent the toner on the paper from scattering and
getting into your eyes or mouth. If the toner gets into your eyes or mouth, wash
them immediately with cold water and immediately consult a physician.
• When removing a jammed paper, take care not to cut your hand on the edges of
the paper.
IMPORTANT
• Be sure not to touch the prohibited portions such as the high-voltage contacts or gears
on the ETB unit. It may result in damaging the printer.
When a Paper Jam Occurs (Clearing Paper Jams)
39
• Do not place any objects on the ETB unit or touch the transfer belt on the ETB unit.
Furthermore, do not clean any loose toner from the transfer belt, as the ETB unit has a
self-cleaning function. If the ETB unit is damaged or the transfer belt is scratched, it may
result in misfeeds or deterioration in print quality.
Transfer belt
Transfer belt
• Remove jammed paper with the printer turned ON. The print data will be erased if the
printer is turned OFF.
• Applying excess force may result in tearing the paper or damaging the printer. When
removing the paper, pull the paper in the proper direction judging from the position of the
paper.
• If paper is torn, be sure to find and remove the remaining portion.
.
1
Confirm all the messages that appear on the display.
An error message is displayed one at a time in order. Confirm all of them.
The messages will disappear when the cover is opened, so write down the
message if necessary.
13 ヨウシガ ツマリマシタ
キュウシ エリア
40
When a Paper Jam Occurs (Clearing Paper Jams)
The following are the messages that indicate the location of the jammed paper.
Displayed message
「キュウシ エリア」
「ハイシ エリア」
「マエカバー エリア」
「ETBユニット エリア」
2
Paper jammed location
Multi purpose tray / Paper cassette
Output tray / Fixing unit
Inside of the front cover
ETB unit (2-sided section)
Check the output tray and if paper is jammed, remove the
paper.
IMPORTANT
If the jammed paper cannot be removed easily, proceed to the next step. Do not try
to remove it forcefully.
NOTE
If there is any unfixed toner on the removed paper, toner stains may be attached on
the following printed page.
3
If paper is being fed from the multi purpose tray, remove paper
that is jammed in the multi purpose tray.
When a Paper Jam Occurs (Clearing Paper Jams)
41
IMPORTANT
If the jammed paper cannot be removed easily, proceed to the next step. Do not try
to remove it forcefully.
4
Close the multi purpose tray.
5
Open the upper front cover.
Open the upper front cover by holding the handles on both sides with both hands
until it stops
IMPORTANT
Perform the following procedure with the upper front cover open. Be careful not to
close the upper front cover accidentally.
42
When a Paper Jam Occurs (Clearing Paper Jams)
6
7
Press down the green pressure release levers on the right and
left sides to the rear and release the pressure that is applied
to the fixing unit.
Raise the lever attached with a green label and open the cover
of the fixing unit.
When a Paper Jam Occurs (Clearing Paper Jams)
43
8
Remove the jammed paper by pulling it in the direction of the
arrow as shown in the figure.
NOTE
If there is any unfixed toner on the removed paper, toner stains may be attached on
the following printed page.
9
Open the lower front cover.
Open the lower front cover with both hands until it stops.
44
When a Paper Jam Occurs (Clearing Paper Jams)
IMPORTANT
Be sure that there are no obstacles in front of the printer before opening the lower
front cover.
10 Remove the jammed paper by pulling it in the direction of the
arrow as shown in the figure below.
When a Paper Jam Occurs (Clearing Paper Jams)
45
11 Hold the handle and open the ETB unit.
Open the ETB unit by pulling it slowly and firmly until it stops.
IMPORTANT
Lower the ETB unit completely until it stops.
12 Remove the jammed paper by pulling it in the direction of the
arrow as shown in the figure below.
Remove the paper carefully, as unfixed toner may be adhered to the paper on the
ETB unit.
46
When a Paper Jam Occurs (Clearing Paper Jams)
13 Close the ETB unit.
Close the ETB unit securely until it clicks.
IMPORTANT
Be sure to close the ETB unit by holding the handles.
14 Return the green pressure release levers on the fixing unit to
their original positions.
When a Paper Jam Occurs (Clearing Paper Jams)
47
15 Close the lower front cover a, then close the upper front
cover b.
Close the upper front cover slowly by holding the handles on both sides with both
hands.
b
a
48
When a Paper Jam Occurs (Clearing Paper Jams)
16 Pull out the paper cassette.
Hold the handle on the front of the cassette to pull it out half way, then support it
with both hands as shown in the figure below to pull it all the way out.
IMPORTANT
• The paper cassette is heavy, so hold it securely with both hands.
• Place the paper cassette on a sturdy, flat surface.
When a Paper Jam Occurs (Clearing Paper Jams)
49
17 Remove the jammed paper by pulling the paper down and
toward you.
18 Attach the paper cassette to the printer.
Hold the cassette securely with both hands and push it into the printer slowly until
the front side of the cassette is flush with front surface of the printer.
CAUTION
Be careful to avoid catching your fingers when inserting the paper
cassette into the printer.
50
When a Paper Jam Occurs (Clearing Paper Jams)
IMPORTANT
If you have trouble attaching the paper cassette to the printer, do not try to push it
in forcefully. Remove the cassette once, adjust it straight and re-insert it into the
printer.
When a Paper Jam Occurs (Clearing Paper Jams)
51
Replacing the Cartridge
This section describes the precautions for replacing, handling, and storing
cartridges.
.
When <X トナー チェック / コウカン > is Displayed
Cartridges are consumables. When the replacement time of the cartridge is
approaching, one of the following messages will appear, therefore, take measures
according to the message.
Message
00
LT A4
00 CAPT2
LIPS
16
ト ナ ー チ ェ ッLOW
ク
16 XX TONER
(X stands for K, M, Y, or C)
16
16 CHANGE
X ト ナ ー コX
ウ カTNR
ン
(X stands for K, M, Y, or C)
1G
1G CHANGE
X ト ナ ー コXウ カTNR
ン
(X stands for K, M, Y, or C)
Displayed Timing
Contents and Remedies
When the replacement
time of the cartridge is
approaching.
- Printing can be continued.
- Have a new cartridge in the indicated
color available.
- Replace the cartridge when printing a
large amount of pages.
When the replacement
time of the cartridge is
approaching.
- The printer will stop.
- Printing can be resumed by pressing [On
Line].
- Have a new cartridge in the indicated
color available.
- Replace the cartridge when printing a
large amount of pages.
When the lifespan of the
cartridge is over.
- The printer will stop and printing cannot
be continued.
- Replace the cartridge of the indicated
color to a new cartridge.
* Whether to display <16 X トナー チェック> or <16 トナー コウカン> when the amount of remaining
toner becomes low depends on how <警告処理> in the settings menu is specified. This machine is
specified so that <16 X トナー チェック> is displayed by factory setting.
* The "K" in the message stands for the black cartridge, "M" for the magenta cartridge, "Y" for the
yellow cartridge, and "C" for the cyan cartridge.
IMPORTANT
When the print is faint or inconsistent, the life span of the cartridge may be over even if
the message <16 X トナー チェック > or <16 トナー コウカン > is not displayed. Do not
continue to use the cartridge when the print quality deteriorates.
52
Replacing the Cartridge
NOTE
The life span of the EP-85 cartridge is indicated below. The number of pages is based on
printing a standard document (with a printing ratio of approximately 5% and print density
adjusted to factory default). Toner consumption of color toners varies depending on the
printed images, therefore, the life span of color toners will vary. Furthermore, printing
black-and-white images can also affect the life span of magenta, yellow, and cyan cartridges.
- EP-85 cartridge (Black): Approx. 9,000 pages of A4
- EP-85 cartridge (Magenta, Yellow, and Cyan): Approx. 8,000 pages of A4
.
Replacing the Cartridge
If the following messages appear on the display, replace the cartridge of the
indicated color to a new cartridge.
• <1G
K トナー コウカン > ... Replace the Black cartridge.
• <1G M トナー コウカン > ... Replace the Magenta cartridge.
• <1G Y トナー コウカン
> ... Replace the Yellow cartridge.
• <1G C トナー コウカン > ... Replace the Cyan cartridge.
WARNING
Do not throw used cartridges into open flames, as this may cause toner
remaining inside the cartridges to ignite and result in burns or a fire.
CAUTION
• Take care not to allow the toner to come into contact with your hands or
clothing, as this will dirty your hands or clothing. If they become dirty, wash
them immediately with cold water. Washing with warm water will set the toner
and make it impossible to remove the toner stains.
• The fixing unit and its surroundings inside the machine may become hot during
use. When removing jammed paper or when inspecting the inside of the
machine, do not touch the fixing unit and its surroundings, as doing so may
result in burns or electrical shock.
IMPORTANT
Be sure to use cartridges that are designed exclusively for this machine.
Replacing the Cartridge
53
.
1
Open the upper front cover.
Open the upper front cover by holding the handles on both sides with both hands
until it stops.
IMPORTANT
Perform the following procedure with the upper front cover open. Be careful not to
close the upper front cover accidentally.
2
Open the lower front cover.
Open the lower front cover with both hands until it stops.
IMPORTANT
Be sure that there are no obstacles in front of the printer before opening the lower
front cover.
54
Replacing the Cartridge
3
Hold the handle and open the ETB unit.
Open the ETB unit by pulling it slowly and firmly until it stops.
IMPORTANT
• Lower the ETB unit completely until it stops.
• Do not place any objects on the ETB unit or touch the transfer belt on the ETB unit.
Furthermore, do not clean any loose toner from the transfer belt, as the ETB unit
has a self-cleaning function. If the ETB unit is damaged or the transfer belt is
scratched, it may result in misfeeds or deterioration in print quality.
Transfer belt
Transfer belt
Replacing the Cartridge
55
4
Place the sheets of paper (A4 size paper is recommended) on
the transfer belt as shown in the figure.
IMPORTANT
Be sure to cover the transfer belt with paper to protect the transfer belt when
installing or removing a cartridge.
5
Grasp the right and left handles on the cartridge of the color
to be replaced and pull it straight out.
A cartridge weighs approximately 3.1 lb (1.4 kg), therefore, hold it securely with
both hands and pull it out without touching the transfer belt in the ETB unit.
56
Replacing the Cartridge
IMPORTANT
The cartridges should be installed in the order of Black, Magenta, Yellow, and Cyan
from the top.
Black
Magenta
Yellow
Cyan
Replacing the Cartridge
57
6
Remove a new cartridge from the box, then remove it from the
protective bag.
Cut the protective bag open with scissors, so as not to damage the cartridge.
IMPORTANT
• Keep the cartridge in the box until it is ready to be installed.
• Do not throw away the protective bag and box in which the cartridge came in. It
may be required for storing the cartridge during printer maintenance.
58
Replacing the Cartridge
7
Remove the tape and protective cover.
Remove the protective cover along with the tape.
IMPORTANT
Do not throw away the protective cover. It may be required for storing the cartridge
during printer maintenance.
8
Hold the cartridge as shown in the figure and shake it gently 5
to 6 times so that toner is distributed in the cartridge evenly.
IMPORTANT
• If the toner is not evenly distributed, it may result in deterioration in print quality. Be
sure that this procedure is executed properly.
• Be sure to shake the cartridge gently. Toner may spill if the cartridge is handled
without caution.
Replacing the Cartridge
59
9
Place the cartridge on a flat surface and pull out the sealing
tape (approx. 19 3/4" (50 cm) in length) slowly while holding
the cartridge.
Hook your finger on the tab of the sealing tape and pull it straight out.
Drum protective
shutter
CAUTION
If the sealing tape is pulled out forcefully or stopped at midpoint, toner
may spill. If toner gets into your eyes or mouth, wash it away immediately
with cold water and consult a physician.
IMPORTANT
• Do not pull the sealing tape diagonally, upwards, or downwards. If the tape is
severed, it may become difficult to remove it completely.
• Remove the sealing tape completely from the cartridge. If the tape remains on the
cartridge, it may result in deterioration in print quality.
• When removing the sealing tape, be careful not to touch the drum protective
shutter.
• Dispose the sealing tape according to the local regulations.
60
Replacing the Cartridge
10 Lift the cartridge with both hands and install it in the printer.
Insert the cartridge into the slot attached with a label in an applicable color, then
push it in until it stops a. Push it into the printer securely as shown in the figure
b.
a
b
IMPORTANT
Install the cartridge by pushing it into the printer securely. If the cartridge is not
installed securely, it may result in deterioration in print quality.
Replacing the Cartridge
61
11 Remove the paper.
IMPORTANT
When removing the paper, be careful not to touch or scratch the transfer belt on the
ETB unit.
12 Close the ETB unit.
Close the ETB unit securely until it clicks.
IMPORTANT
• Be sure to close the ETB unit by holding the handle.
• Do not leave the ETB unit open for a long time after installing a cartridge.
62
Replacing the Cartridge
13 Close the lower front cover a, then close the upper front
cover b.
Close the upper front cover slowly by holding the handles on both sides with both
hands.
b
a
Replacing the Cartridge
63
Canceling Printing
To cancel printing currently being processed, follow the procedure described below
to perform job cancel. Job cancel lets you cancel a job while data is being received
or processed. It does not affect the print data for the next job or any other interface
jobs for which data processing has not begun.
IMPORTANT
• Perform job cancel offline when data is being processed (when the ジョブ indicator
is on or flashing). If you press [ジョブキャンセル ] when the ジョブ indicator is off, job
cancel cannot be performed.
• Data that has already been processed and is currently being printed (when paper
feeding has begun) cannot be canceled. In this case, be careful because
performing job cancel may cancel the print data for the next job.
• If print data sent from a printer driver not compatible with this printer is mixed with
other data, multiple print jobs may be canceled.
NOTE
When job cancel is performed, the message <03 ジョブ キャンセル> is displayed.
However, the print job data may not be canceled.
Follow the procedure described below to perform job cancel. Only perform job
cancel when the ジョブ indicator is on or flashing (when the print data for the job you
want to cancel is being received or processed).
1
Press [ オンライン ].
The オンライン indicator is turned off and the printer gets ready for operation
using the control panel.
NOTE
The display changes depending on the printer status. During job processing, the
operation mode is shown on the upper part of display, a user name and print status
are shown on the lower part of the display.
64
Canceling Printing
2
Press [ ジョブ キャンセル ].
The message <03 ジョブ キャンセル> appears on the display and the print data
being processed is canceled. When processing takes time, such as when
receiving data, the message on the display changes to <00 ジョブ スキップ >.
When the message <00 LIPS > appears on the display, job cancel is complete.
IMPORTANT
• When the message <00 ジョブ スキップ > appears on the display, you can press
[リセット] to perform a soft reset or hard reset. If you perform a reset, any print data
being received or any other interface print data will be lost. In this case, perform
printing again.
• When the message <03 ジョブ キャンセル > appears on the display, you cannot
perform a soft reset or hard reset. Wait until job cancel is complete or the message
<00 ジョブ スキップ > appears on the display.
Canceling Printing
65
Checking Operations
This machine is equipped with a status print function that enables you to confirm
the values specified in the printer menu.
This function can be used when you want to check the operating status, etc. of the
machine, whenever the printer is connected and ready to operate.
.
Status Print
Status print is for printing a list of functions that can be currently used by the printer,
or a list of values specified in the menus. Status print is performed in the following
procedure.
NOTE
• A4 paper is specified for status print. The lists can be printed on paper in other sizes,
however, data may be enlarged / reduced, cut off, or misaligned on paper other than A4
size.
• The values specified in the menus from the control panel on the printer will also be
reflected in status print. For example, if two-sided print is specified, two pages worth of
data will also be printed on both sides of paper for status print. However, copy quantity is
neglected, therefore, it will constantly print one page at a time.
.
1
Press [ オンライン ].
The オンライン indicator will go off and items can be specified from the control
panel.
ユーティリティ
2
Press [ ユーティリティ ].
ユーティリティ
ステータス プリント
→
< ステータス プリント > will appear in the display.
66
Checking Operations
実行
3
Press [ 実行 ].
ユーティリティ
ステータス プリント
→
01 ステータス プリント
<01 ステータス プリント > will appear in the display and status print will be
printed.
Checking Operations
67
4
Check the contents printed in status print.
Status print is printed as shown below. In status print, you can confirm the
functions that can be currently used, items specified in the printer function menu
and their values, versions of the software and hardware installed in the printer,
and print quantity.
IMPORTANT
The status print shown below is a sample. It may differ from the status print that is
printed from your printer.
68
Checking Operations
When a Message Is Displayed
When <nn-nn サービス コール > or <F9-nn チェック
プリンタ > Is Displayed
If a problem has occurred in internal devices of the printer or if a problem has
occurred while print data was being processed, an error message (error code and
message) is displayed. An error code is the four-digit number as shown in the
illustration below.
Error code
Message
5F-50 サービス コール
Error code
Message
F9-nn チェックプリンタ
1
When these types of messages are
displayed, make a note of the four-digit
number on the display, and then take the
following actions.
Turn OFF the printer and turn it ON after 3 seconds or longer.
OFF
ON
If the message does not appear, the printer can be used in its current status.
However, if the message still appears, proceed to the next step.
When a Message Is Displayed
69
2
3
Write down the four-digit alphanumeral along the message
that are indicated on the display.
Turn OFF the printer a, and unplug the power cord from the
outlet b.
b
a
4
Contact the store where the printer was purchased.
Please notify the symptoms and the four-digit alphanumeral.
Error Messages
If printer operation is disabled for some reason (error status), an alarm will sound,
the メッセージ indicator will illuminate, and an error message indicating the problem
will appear on the display. Furthermore, a warning message will appear on the
bottom line on the display when some kind of measure must be applied, even
though there is no problem with the print job (warning status).
When such messages are displayed, apply measures according to the message.
NOTE
• When more than one warning status occurs at the same time, the messages are
displayed alternately.
• When an error status and warning status occurs at the same time, the warning message
is not displayed.
• When <警告表示 > in the settings menu is specified to < シナイ>, a message attached with
a (Warning Message) symbol will not be displayed even when a warning status occurs.
70
When a Message Is Displayed
• When an error in which the message is attached with an (Error Skip) symbol occurs, the
error can be bypassed (error skip) by pressing [ オンライン ] to continue the print job,
however, print data may be lost or the data may not be printed accurately in such a case.
If you want to cancel the process, perform a soft reset to release the problem, then press
[オンライン ] to print the data again. Furthermore, messages marked with this symbol can
be skipped automatically by specifying < 自動エラースキップ > in the settings menu to
< ツカウ >.
Cause and Remedy
Message
Cause:
11 XXX ヨウシガ アリマセン
(where XXX is the paper size
abbreviation)
The paper size specified in an
application software has not been
loaded in the paper cassette or
paper tray. (When the paper feed
mode is set to [ 自動 ], this applies to
paper cassette and the paper tray.
When the paper feed mode is fixed,
this applies to a paper cassette or
paper tray.)
Remedy: Add paper to the paper source or, if
there is no paper in the paper
source, load paper into it.
12 カバーガ アイテイマス
Cause: The upper/lower cover is open.
Remedy: Close the upper/lower cover firmly.
13 ヨウシガ ツマリマシタ
Cause: Paper has jammed inside the printer.
Remedy: Clear the paper jam.
Cause:
14 X カートリッジ ナシ
(X is Y , M, C, or K.)
The toner cartridge for the color
indicated on the display has not been
installed or it has not been installed
correctly.
Remedy: Install the toner cartridge or re-install
the toner cartridge correctly.
Cause:
16 X トナー チェック
(X is Y , M, C, or K.)
<Warning message>
The amount of remaining toner for
the color indicated on the display is
low.
Remedy: Printing can be continued, however
you should prepare the new
cartridge. If you are printing a large
volume, we recommend that you
replace the cartridge.
When a Message Is Displayed
71
Cause:
16 X トナー コウカン
(X is Y , M, C, or K.)
<Error skip>
17 カセット 1 ヨウシ ナシ <Warning message>
The cartridge for the color indicated
on the display is almost out of toner.
Remedy: Press [ オンライン ] to continue
printing. Printing can be continued
for a while however you should
prepare the new cartridge. If you are
printing a large volume, we
recommend that you replace the
cartridge.
Cause: Paper in the cassette 1 has run out.
Remedy: Load paper into the cassette 1.
Cause:
18 カセット キュウシ フカ
The paper type specified cannot be
fed from the paper cassette.
Remedy: Only plain paper can be fed from the
paper cassette. Set [ デフォルト用紙タ
イプ ] to [ フツウシ ] or switch the
paper source to the paper tray before
you print.
1F ハイシトレイ チェック
<Warning message>
Cause: Output tray is almost full.
Remedy: Remove the paper from the output
tray.
1F ハイシトレイ フル
<Error skip>
Cause: Output tray is full.
Remedy: Remove the paper from the output
tray.
Cause:
1G X トナー コウカン
(X is Y , M, C, or K.)
The cartridge for the color indicated
on the display is out of toner.
Remedy: Replace the toner cartridge with a
new one.
Cause:
1H X カートリッジ コショウ
(X is Y , M, C, or K.)
There is a problem with the cartridge
of the color displayed.
Remedy: Replace the toner cartridge with a
new one.
Cause:
32 リョウメン フカノウ
<Error skip>
72
When a Message Is Displayed
The paper specified cannot be
duplex printed.
Remedy: Select the paper source on the
printer with standard-size paper
loaded, and set the paper size
setting on the PC to standard-size.
Then start printing again.
Cause:
37 ヨウシタイプ フカノウ
The paper type specified cannot be
printed.
Remedy: Press [ オンライン ] and the paper will
be printed as plain paper. If the
paper is not plain paper, the data
may not be printed properly.
Cause:
40 ツウシン エラー
<Error skip>
An error occurred when data was
being transferred between a PC and
the printer.
Remedy: Check the interface cable connection
and print the data again.
Cause:
41 プリント チェック
<Error skip>
The sizes of the paper loaded in the
paper cassette and paper tray are
different to the paper size settings
specified on the PC or the control
panel.
Remedy: When paper is being fed from the
paper cassette, make sure that the
size of the paper loaded in the paper
cassette is the same as the paper
size settings for the paper cassette.
Also when paper is being fed from
the paper tray, make sure that the
size of the paper loaded in the paper
tray is the same as the paper size
settings for the paper tray before you
press [ オンライン ].
Cause:
9A カセット 1 ガイドフセイ
The paper guides of the cassette 1 is
out of position.
Remedy: Set the paper guides to the size of
the paper loaded in the cassette 1.
Cause:
9B ヨウシ フセイ
<Error skip>
The type of the paper fed from the
paper cassette or paper tray is
different to the paper type setting.
Remedy: Press[オンライン ] to cancel the print
job. Correct the paper type setting or
load the paper of the type specified
in the paper type setting into the
paper cassette or paper tray.
Cause:
9E カートリッジ ミスマッチ
The cartridge has been installed in
the wrong position.
Remedy: Remove the cartridge indicated on
the display from the printer, and then
re-install it in the correct position.
When a Message Is Displayed
73
Cause:
9F X カートリッジ ケイコク
(X is Y , M, C, or K.)
It is possible that there is a problem
with the installed cartridge.
Therefore, the print quality cannot be
guaranteed.
Remedy: Replacing the toner cartridge with a
new one is recommended.
Cause:
9G X カートリッジ フセイ
(X is Y , M, C, or K.)
The print quality of the installed
cartridge cannot be guaranteed, or a
cartridge that has been completely
used previously is installed.
Remedy: If you press [ オンライン ] , you will be
able to print. If you continue to use
the cartridge, a printer malfunction
may occur. Replace the toner
cartridge with a new one.
Cause:
9H X カートリッジ チェック
(X is Y , M, C, or K.)
It is possible that there is a problem
with the installed cartridge.
Therefore, the print quality cannot be
guaranteed.
Remedy: Replace the toner cartridge with a
new one.
Cause:
PC XXX ヨウシ ニ コウカン (where XXX is the paper size
abbreviation)
<Error skip>
74
When a Message Is Displayed
Either the size of the paper loaded in
the paper source is different to the
paper size setting in the application
software, or the paper source in
which a different size of paper is
loaded has been selected.
Remedy: Replace the paper in the selected
paper source with paper of the size
specified by the application software
(or scaling setting).