Setup guide | Canon MP970 All in One Printer User Manual

Start Here
Easy Setup Instructions
Unpack the Machine
Photo All-In-One
• Please confirm the included items against the illustration printed on the lid of the packing box.
• A USB cable is necessary to connect the machine with your computer.
1 Prepare the Machine
Important
When cleaning the exterior of the machine, use a soft cloth to wipe it gently. For details, refer to “Cleaning Your Machine” in the Quick Start Guide.
2 Install the Print Head
Important
Before turning on the machine, remove all the orange shipping
tapes.
aUnlock the Scanning Unit (Printer Cover).
dUse the { or } button on the Operation Panel to
select the language for the LCD, then press the
OK button.
aRemove the Print Head from its package.
Caution
There may be some transparent or light blue ink on the inside
of the bag the print head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to
get ink on yourself when handling these items.
(1) Press the { or }
button to select the
language.
(1)
bRemove the orange protective cap from the Print
(2) Press the OK
button.
Head and discard it.
Electrical Contacts
Important
If an unintended language is displayed on the LCD, press the
Back button on the Operation Panel to return to the Language
selection screen.
Caution
• Make sure to unlock the Scanning Unit (Printer Cover) before
turning on the machine.
• Before transporting the machine, always lock the Scanning
Unit (Printer Cover) by moving the Scanner Lock Switch
towards the lock mark.
Note
For the ink tanks compatible with this machine, refer to the back
cover of the Quick Start Guide.
aPinch the Paper Guide and slide it to the left end.
Paper Support
to peel off the protective film and remove the film
completely.
(2) Move the Scanner Lock Switch towards the release mark to
unlock the Scanning Unit (Printer Cover).
Scanning Unit
(Printer Cover)
4 Align the Print Head
aPull the orange tape in the direction of the arrow
(1) Open the Document Cover.
(2)
3 Install the Ink Tanks
bTwist off and discard the orange protective cap
located on the bottom of the ink tank.
Ink Port
Print Head Nozzles
Protective Cap
Important
Do not touch the print head nozzles or the electrical contacts.
cFirmly raise the Print Head Lock Lever until
it stops. The Print Head Lock Lever may feel
heavy.
and connect the other end to the wall outlet.
Next, open the Sheet Feeder Cover, pull out the
Paper Support and the Extension, then open the
Paper Output Tray and the Extension.
If the air hole is blocked with the remaining film, ink
may leak out or may not eject properly.
bLoad a sheet of A4 or Letter-sized plain paper
into the Rear Tray, align the paper with the Cover
Guide on the right side, then slide the Paper
Guide against the paper.
Do not press!
eLift the Scanning Unit (Printer Cover) until it locks
bPlug the power cord in the back of the machine
Paper Guide
Protective Cap
Once the message “Install the print head and set the ink
tank.” appears, go to e.
into place. The Print Head Holder moves to the
center.
Extension
Electrical Contacts
Paper Guide
Important
• Do not touch the electrical contacts.
• Do not touch the ink port.
Print Side
cInsert the ink tank into the right-hand slot and
press the
into place.
mark on the ink tank until it clicks
Extension
Document Cover
Cover Guide
cMake sure that Yes is selected in the message
requesting head alignment, then press the OK
button.
Paper Support
dInsert the Print Head.
Paper Output Tray
Extension
dMake sure the ink lamp lights red.
Sheet Feeder
Cover
Do not touch!
Important
• Make sure that the Document Cover is closed.
• Do NOT connect the USB cable at this stage.
cOpen the Operation Panel, then press the ON/
OFF button to turn on the machine.
The machine will initialize. Wait until the Power lamp stops
flashing and remains lit blue.
Caution
For your safety, always firmly grip the areas illustrated when
lifting the Scanning Unit (Printer Cover).
Important
If the Document Cover is opened, you cannot open the Scanning Unit (Printer Cover). Be sure to open the Scanning Unit
(Printer Cover) with the Document Cover closed.
ePush the Print Head to hold it in place, and lower
the Print Head Lock Lever.
Refer to the color
guide on the Print
Head Lock Lever.
eClose the Scanning Unit (Printer Cover).
The pattern is printed. And Print Head is aligned
automatically.
fWrite down the serial number located inside
the machine. You will need this to register your
product.
OK
Important
If the Scanning Unit (Printer Cover) is left open for more than
10 minutes, the Print Head Holder moves to the right. Close
and reopen the Scanning Unit (Printer Cover) to return the
Holder to the center.
Serial Number Location
Note
Print Head alignment takes about 6 minutes to complete. Do not
start another operation until the machine has stopped making
operating noises.
Caution
For your safety, always firmly grip the areas illustrated when
closing the Scanning Unit (Printer Cover).
Important
The machine starts the preparatory operation. It takes about 2
minutes. Do not start another operation until the machine has
stopped making operating noises.
Note
• The pattern is printed in black and blue.
• When Automatic Print Head Alignment cannot be executed
correctly, the message “Auto head align has failed.” is displayed
on the LCD. Refer to “An Error Message is Displayed on the LCD”
in the Quick Start Guide.
Hardware setup and Print Head alignment are
complete.
USB connection is explained here. For wired LAN connection, refer to the Network Setup Guide.
Macintosh® Software Installation
hWhen the Setup Complete screen appears, click Next.
sh
gWhen the list of applications to install appears, confirm the
in
to
contents and click Install.
ac
Note
Move the cursor over items to display explanations of each application.
M
W
in
do
w
s
Windows® Software Installation
hRead the License Agreement carefully and click Yes. The
Note
• The screens below refer to Windows Vista™ operating system Ultimate Edition
(hereafter referred to as “Windows Vista”) installation.
Screens may vary depending on the operating system you are using.
• Log into a user account with the administrator privilege.
• Before installing the software, disable all anti-virus programs and automatically
loading programs.
• A message asking for your confirmation to restart your computer may appear
during the installation process. If this message is displayed, follow the on-screen
instructions and click OK.
The installation resumes from where it left off when your computer has been
restarted.
• If the computer is restarted during installation, do not remove the Setup CD-ROM
during restarting.
software installation screen may appear during the installation
process. Follow the on-screen instructions to install the
software.
iWhen the Setup Method screen appears, select Use the
printer via USB, then click Next.
aConnect one end of the USB cable to the computer and the
other to the machine.
Note
Make sure the machine is turned on.
aBe sure to TURN THE MACHINE OFF before continuing.
(1) Press the ON/OFF button.
(2) Make sure that the Power lamp stops flashing.
bTurn the computer on and start Windows.
Important
If the Found New Hardware or Found New Hardware Wizard screen appears
automatically, remove the USB cable connected to your computer. Click Cancel
to quit the screen. In Windows Vista, the screen may close automatically when
the USB cable is unplugged. Then turn off the machine and proceed from step
c to install the software.
Note
• Since Mac® OS 9, Mac OS X Classic environments, or Mac OS X v.10.2.7 or earlier
are not supported, do not connect the machine to these.
• The screens below refer to Mac OS X v.10.4.x installation. Screens may vary
depending on the operating system you are using.
• Log on as an Administrator.
• Before installing the software, disable all anti-virus programs and automatically
loading programs.
iWhen the User Registration screen appears, click Next.
Note
To register later, click Cancel and go to Step j. After software installation is complete,
double-click
on the desktop.
Follow the on-screen instructions to register your product. You will need your
product serial number, which is located on the inside of the machine. See
Step 1- f on the front page.
jWhen the Installation completed successfully screen
jWhen the Printer Connection screen appears, connect
one end of the USB cable to the computer, the other to the
machine, then TURN THE MACHINE ON. The software will
begin identifying the printer port being used.
appears, click Restart.
Remove the CD-ROM after clicking Restart and restarting the computer.
Important
If you cannot go to the next procedure after three minutes, refer to “Cannot
Install the MP Drivers” in the Quick Start Guide.
USB
bTurn on your Mac and insert the Setup CD-ROM.
→
USB
cInsert the Setup CD-ROM. The setup program should run
automatically.
In Windows Vista, go to Step d. In Windows XP and Windows 2000, go to
Step f.
dIf the AutoPlay screen appears, click Run Msetup4.exe.
To Computer
When using Windows 2000:
When you connect the machine to the computer with a USB cable, a
message asking for your confirmation to restart your computer is displayed.
Click Yes. Then when an error message is displayed, click OK to proceed
with the installation.
kWhen the Setup Complete screen appears, click Next.
Note
If the CD-ROM folder does not open automatically, double-click the CD-ROM icon
on the desktop.
cDouble-click the Setup icon.
dWhen the Authenticate screen appears, enter your
administrator name and password. Click OK.
If you do not know your administrator name or password, click
, then follow the on-screen instructions.
eWhen the main menu appears, click Easy Install.
The MP Drivers, On-screen Manuals, and application software are installed
automatically.
Note
Keep the CD-ROM in a safe place in case you need to reinstall the software.
When the computer restarts, the Canon IJ Network Tool will start up
automatically.
When using Mac OS X v.10.2.8 to v.10.3.3:
Restarting the computer while connected to the machine may cause the
machine not to be detected. To resolve this, either unplug the USB cable
then plug it back in again, or turn the machine off then back on again.
Note
When using Mac OS X v.10.2.8 to v.10.3.x, before using the Operation Panel on
the machine to save scanned originals to the computer, it is necessary to select MP
Navigator EX as the launch application on Image Capture under Applications. For
details, refer to “Scanning Images” in the User’s Guide on-screen manual.
kWhen the Canon IJ Network Tool screen appears, select
USB connection, then click OK.
lWhen the User Registration screen appears, click Next.
eIf the User Account Control screen appears, click Continue.
If the same screen reappears in subsequent steps, click
Continue.
Note
To register later, click Cancel and go to Step m. After software installation is complete,
double-click
on the desktop.
Follow the on-screen instructions to register your product. You will need your
product serial number, which is located on the inside of the machine. See
Step 1- f on the front page.
mWhen the PIXMA Extended Survey Program screen
fWhen the main menu appears, click Easy Install.
The MP Drivers, On-screen Manuals, and application software are installed
automatically.
appears, confirm the message. We would appreciate it if you
would take part in this program regarding the use of Canon
printers. If you can agree, click Agree.
nWhen the Installation completed successfully screen
appears, click Exit.
After clicking Exit, remove the CD-ROM.
Note
If you want to select particular items to install, click Custom Install and follow the onscreen instructions to proceed with the installation.
fWhen the list of applications to install appears, confirm the
contents, then click Install.
Software installation is now complete.
Note
Move the cursor over items to display explanations of each application.
gRead the License Agreement carefully and click Yes. The
software installation screen may appear during the installation
process. Follow the on-screen instructions to install the
software.
If Restart is displayed, make sure that the Restart the system now
(recommended) check box is selected, then click Restart.
Remove the CD-ROM after clicking Restart and restarting the computer.
Note
If you want to select particular items to install, click Custom Install and follow the onscreen instructions to proceed with the installation.
Note
Keep the CD-ROM in a safe place in case you need to reinstall the software.
Software installation is now complete.
Part no. QT5-1178-V01 © 2007 Canon Inc. “Microsoft” is a registered trademark of Microsoft Corporation. “Windows” is a trademark of Microsoft Corporation, registered in the U.S. and other countries. “Windows Vista” is a trademark of Microsoft Corporation. “Macintosh” and “Mac” are trademarks of Apple Inc., registered in the U.S. and other countries.
XXXXXXXX
PRINTED IN THAILAND
Download PDF

advertising