Sony | STR-DE497 | Operating instructions | Canon MX340 Printer User Manual

lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB01COV_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 1 Friday, July 16, 2004 2:34 PM
4-252-084-13(1)
FM Stereo
FM/AM Receiver
Operating Instructions
STR-DE497
©2004 Sony Corporation
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB02REG_STRDE497-CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 2 Friday, July 16, 2004 2:34 PM
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To prevent fire, do not cover the ventilation of the
apparatus with newspapers, table-cloths, curtains, etc.
And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
Don’t throw away batteries with
general house waste; dispose of
them correctly as chemical waste.
Except for customers in Europe
ENERGY STAR® is a U.S. registered
mark. As an ENERGY STAR® partner,
Sony Corporation has determined that
this product meets the ENERGY
STAR® guidelines for energy
efficiency.
2GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB02REG_STRDE497-CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 3 Friday, July 16, 2004 2:34 PM
About This Manual
• The instructions in this manual are for model
STR-DE497. Check your model number by looking
at the lower right corner of the front panel.
• The instructions in this manual describe the controls
on the receiver. You can also use the controls on the
supplied remote if they have the same or similar
names as those on the receiver. For details on the use
of your remote, see pages 38-41.
About area codes
The area code of the receiver you purchased is
shown on the lower portion of the rear panel (see
the illustration below).
+
R
CENTER
L
FRONT A
4-XXX-XXX-XX AA
Area code
Any differences in operation, according to the area
code, are clearly indicated in the text, for example,
“Models of area code AA only”.
This receiver incorporates Dolby* Digital and Pro
Logic Surround and the DTS** Digital Surround
System.
* Manufactured under license from Dolby
Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
**“DTS” and “DTS Digital Surround” are registered
trademarks of Digital Theater Systems, Inc.
3GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB01COV_STR-DE497CELTOC.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 4 Friday, July 16, 2004 2:34 PM
Table of Contents
Getting Started
1: Check how to hookup your
components....................................... 5
1a: Connecting components with
digital audio output jacks ........... 7
1b: Connecting components with
multi channel output jacks........ 10
1c: Connecting components with only
analog audio jacks .................... 12
2: Connecting the antennas ................... 14
3: Connecting speakers ......................... 15
4: Connecting the AC power cord ........ 17
5: Setting up the speakers ..................... 18
6: Adjusting the speaker levels and
balance ............................................ 20
— TEST TONE
Amplifier Operation
Selecting the component ....................... 21
Listening to multi channel sound.......... 21
— MULTI CH IN
Listening to FM/AM radio.................... 22
Storing FM stations automatically ........ 23
— AUTOBETICAL
(Models of area code CEL, CEK
only)
Presetting radio stations ........................ 23
Using the Radio Data System (RDS).... 24
(Models of area code CEL, CEK
only)
Changing the display............................. 26
About the indications in the display...... 27
Advanced Adjustments and
Settings
Switching the audio input mode for digital
components..................................... 31
— INPUT MODE
Customizing sound fields ..................... 31
Adjusting the tone................................. 33
Advanced settings................................. 33
Other Operations
Naming preset stations and inputs ........ 35
Using the Sleep Timer .......................... 36
Selecting the speaker system ................ 36
Recording ............................................. 37
Operations Using the Remote
RM-U306B
Before you use your remote.................. 38
Remote button description.................... 38
Changing the factory setting of an input
button.............................................. 41
Additional Information
Precautions ........................................... 42
Troubleshooting.................................... 43
Specifications ....................................... 45
List of button locations and reference
pages............................................... 48
Index ..................................................... 50
Enjoying Surround Sound
Using only the front speakers ............... 28
Enjoying higher fidelity sound.............. 28
— AUTO FORMAT DIRECT
Selecting a sound field .......................... 29
4GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 5 Friday, July 16, 2004 2:34 PM
Getting Started
Steps 1a through 1c beginning on page 7 describe how to hook up your components to this receiver.
Before you begin, refer to “Connectable components” below for the pages which describe how to
connect each component.
After hooking up all your components, proceed to “2: Connecting the antennas” (page 14).
Getting Started
1: Check how to hookup your components
Connectable components
Component to be connected
Page
DVD player
With digital audio outputa)
7–8
With multi channel audio outputb)
10–11
With analog audio output onlyc)
7–8
TV monitor
With composite video input only
8, 11 or 13
Satellite tuner
With digital audio outputa)
7–8
With analog audio output onlyc)
7–8
Super Audio CD/CD player
With digital audio outputa)
9
With multi channel audio outputb)
10
With analog audio output onlyc)
12
MD/Tape deck
With analog audio output onlyc)
12
Multi channel decoder
10
VCR
13
a)
b)
c)
Model with a DIGITAL OPTICAL OUTPUT or DIGITAL COAXIAL OUTPUT jack, etc.
Model with a MULTI CH OUTPUT jacks, etc. This connection is used to output the audio decoded by the
component’s internal multi channel decoder through this receiver.
Model equipped only with AUDIO OUT L/R jacks, etc.
continued
5GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 6 Friday, July 16, 2004 2:34 PM
Required cords
The hookup diagrams on the subsequent pages assume the use of the following optional connection
cords (A to F) (not supplied).
A Audio cord
White (L)
Red (R)
B Audio/video cord
D Optical digital cord
E Coaxial digital cord
Yellow (video)
White (L/audio)
Red (R/audio)
F Monaural audio cord
C Video cord
Tip
Yellow
Black
Audio cord A can be torn into two monaural audio
cords F.
Notes
• Turn off the power to all components before making any connections.
• Be sure to make connections firmly to avoid hum and noise.
• When connecting an audio/video cord, be sure to match the color-coded pins to the appropriate jacks on the
components: yellow (video) to yellow; white (left, audio) to white; and red (right, audio) to red.
• When connecting optical digital cords, insert the cord plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
6GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 7 Friday, July 16, 2004 2:34 PM
.
1a: Connecting components with digital audio output jacks
Getting Started
Hooking up a DVD player or satellite tuner
For details on the required cords (A–F), see page 6.
1 Connect the audio jacks.
DVD player
OUTPUT
AUDIO
OUT
OUTPUT
L
DIGITAL
COAXIAL
R
E
A
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
SA-CD/
CD
IN
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
SUB
FRONT SURROUND WOOFER
MULTI CH IN
IN
SA-CD/CD
R
OUT R IN
MD/TAPE
R AUDIO IN
DVD VIDEO 2
AUDIO IN
D
AUDIO OUT R AUDIO IN
VIDEO 1
SUB
WOOFER
A
OUTPUT
OUTPUT
DIGITAL
OPTICAL
AUDIO
OUT
L
R
Satellite tuner
Note
You can listen to the sound of your TV by connecting your TV’s audio output jacks to the VIDEO 2 AUDIO IN jacks
on the receiver. In this case, do not connect the TV’s video output jack to the VIDEO 2 VIDEO IN jack on the
receiver.
continued
7GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 8 Friday, July 16, 2004 2:34 PM
2 Connect the video jacks.
TV monitor
Satellite tuner
OUTPUT
INPUT
VIDEO
VIDEO
C
C
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
SA-CD/
CD
IN
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
SUB
FRONT SURROUND WOOFER
MULTI CH IN
R
IN
SA-CD/CD
OUT R IN
MD/TAPE
R AUDIO IN
DVD VIDEO 2
AUDIO IN
AUDIO OUT R AUDIO IN
VIDEO 1
SUB
WOOFER
C
OUTPUT OUTPUT
VIDEO
DVD player
8GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 9 Friday, July 16, 2004 2:34 PM
Hooking up a Super Audio CD/CD player
Getting Started
For details on the required cords (A–F), see page 6.
Super Audio CD/CD player
OUTPUT
LINE
DIGITAL
L
OPTICAL
OUT
R
D
A
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
SA-CD/
CD
IN
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
SUB
FRONT SURROUND WOOFER
MULTI CH IN
IN
SA-CD/CD
R
OUT R IN
MD/TAPE
R AUDIO IN
DVD VIDEO 2
AUDIO IN
AUDIO OUT R AUDIO IN
VIDEO 1
SUB
WOOFER
Tip
All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz and 96 kHz sampling frequencies.
Note
The sound is not output when you play a Super Audio CD on the Super Audio CD player connected to the SA-CD/
CD OPTICAL IN jack on this receiver. Connect to the analog input jacks (SA-CD/CD IN jacks). Refer to the
operating instructions supplied with the Super Audio CD player.
9GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 10 Friday, July 16, 2004 2:34 PM
1b: Connecting components with multi channel output
jacks
1 Connect the audio jacks.
If your DVD or Super Audio CD player is equipped with multi channel output jacks, you can connect
it to this receiver’s MULTI CH IN jacks to enjoy the multi channel sound. Alternatively, the multi
channel input jacks can be used to connect an external multi channel decoder.
For details on the required cords (A–F), see page 6.
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
SA-CD/
CD
IN
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
SUB
FRONT SURROUND WOOFER
MULTI CH IN
A A
FRONT
IN
SA-CD/CD
R
OUT R IN
MD/TAPE
R AUDIO IN
DVD VIDEO 2
AUDIO IN
AUDIO OUT R AUDIO IN
VIDEO 1
SUB
WOOFER
F F
SURROUND CENTER
L
R
MULTI CH OUT
SUB
WOOFER
DVD player,
Super Audio CD player,
Multi channel decoder, etc.
Tip
This connection also allows you to enjoy software with multi channel audio recorded in formats other than the Dolby
Digital and DTS.
Note
When you make connections to the MULTI CH IN jacks, you will need to adjust the level of the surround speakers
and sub woofer using the controls on the connected component.
10GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 11 Friday, July 16, 2004 2:34 PM
2 Connect the video jacks.
DVD player
OUTPUT
INPUT
VIDEO
VIDEO
C
Getting Started
TV monitor
C
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
SA-CD/
CD
IN
VIDEO IN
VIDEO IN VIDEO OUT VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
SUB
FRONT SURROUND WOOFER
MULTI CH IN
IN
SA-CD/CD
R
OUT R IN
MD/TAPE
R AUDIO IN
DVD VIDEO 2
AUDIO IN
AUDIO OUT R AUDIO IN
VIDEO 1
SUB
WOOFER
11GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 12 Friday, July 16, 2004 2:34 PM
1c: Connecting components with only analog audio jacks
Hooking up audio components
For details on the required cords (A–F), see page 6.
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
SA-CD/
CD
IN
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
MULTI CH IN
IN
OUT R IN
MD/TAPE
R
SA-CD/CD
l
A
A
OUT
A
AUDIO OUT R AUDIO IN
VIDEO 1
SUB
WOOFER
IN
INPUT OUTPUT
OUTPUT
LINE
LINE
Super Audio CD/CD
player
R AUDIO IN
DVD VIDEO 2
AUDIO IN
l
SUB
FRONT SURROUND WOOFER
LINE
L
L
R
R
MD/Tape deck
12GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 13 Friday, July 16, 2004 2:34 PM
Hooking up video components
VCR
INPUT OUTPUT
VIDEO
IN
VIDEO
OUT
AUDIO
IN
AUDIO
OUT
Getting Started
If you connect your TV to the MONITOR VIDEO OUT jack, you can watch the video from the selected
input (page 21). For details on the required cords (A–F), see page 6.
TV monitor
INPUT
L
VIDEO
B
B
L
R
L
OUT
C
IN
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
SA-CD/
CD
IN
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
SUB
FRONT SURROUND WOOFER
MULTI CH IN
IN
SA-CD/CD
R
OUT R IN
MD/TAPE
R AUDIO IN
DVD VIDEO 2
AUDIO IN
AUDIO OUT R AUDIO IN
VIDEO 1
SUB
WOOFER
B
OUTPUT
VIDEO
OUT
AUDIO
OUT
L
R
VCR
13GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 14 Friday, July 16, 2004 2:34 PM
2: Connecting the antennas
Connect the supplied AM loop antenna and FM wire antenna.
AM loop antenna
(supplied)
FM wire antenna
(supplied)
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
SA-CD/
CD
IN
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
SUB
FRONT SURROUND WOOFER
MULTI CH IN
IN
SA-CD/CD
R
OUT R IN
MD/TAPE
R AUDIO IN
DVD VIDEO 2
AUDIO IN
AUDIO OUT R AUDIO IN
VIDEO 1
SUB
WOOFER
*
*
The shape of the connector varies depending on the area code.
Notes
• To prevent noise pickup, keep the AM loop antenna away from the receiver and other components.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as horizontal as possible.
14GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 15 Friday, July 16, 2004 2:34 PM
3: Connecting speakers
Example of 5.1 channel speaker system configuration
Getting Started
Connect your speakers to the receiver. This receiver allows you to use a 5.1 channel speaker system.
To fully enjoy theater-like multi channel surround sound requires five speakers (two front speakers, a
center speaker, and two surround speakers) and a sub woofer (5.1 channel).
Center speaker
Front speaker (Right)
Surround speaker (Right)
Front speaker (Left)
Sub woofer
Surround speaker (Left)
Tip
Since the sub woofer does not emit highly directional signals, you can place it wherever you want.
continued
15GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 16 Friday, July 16, 2004 2:34 PM
Required cords
A Speaker cords (not supplied)
B Monaural audio cord (not supplied)
(+)
(–)
Black
Surround speaker
(Right)
E
Surround speaker
(Left)
e
E
Center speaker
e
A
E
e
A
A
MONITOR
VIDEO OUT
+
R
L
+
+
R
R
L
L
AUDIO
OUT
SUB
WOOFER
R
L
FRONT B
SURROUND
FRONT A
CENTER
SPEAKERS
SPEAKERS
FRONT B*
A
B
A
INPUT
E
AUDIO
IN
Sub woofer
e
Front speaker
(Right)
E
e
Front speaker
(Left)
* If you have an additional front speaker system, connect them to the SPEAKERS FRONT B terminals. You can
select the front speakers you want to use with the SPEAKERS (OFF/A/B/A+B) button. For details, see “Selecting
the speaker system” (page 36).
16GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 17 Friday, July 16, 2004 2:34 PM
Setting the voltage selector
If your receiver has a voltage selector on the rear
panel, check that the voltage selector is set to the
local power supply voltage. If not, use a
screwdriver to set the selector to the correct
position before connecting the AC power cord to
a wall outlet.
VOLTAGE SELECTOR
120V
220V
240V
Connecting the AC power
cord
Connect the AC power cord to a wall outlet.
AC power cord
Performing initial setup
operations
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure.
This procedure can also be used to return
settings you have made to their factory defaults.
Use the buttons on the receiver for the operation.
1
2
Getting Started
4: Connecting the AC
power cord
Press ?/1 to turn off the receiver.
Hold down ?/1 for 5 seconds.
“PUSH” and “ENTER” appears in the
display alternatingly.
3
Press ENTER.
“CLEARING” appears in the display for a
while, then “CLEARED” appears.
The following are reset to their factory
settings.
• All settings in the SET UP, LEVEL,
TONE and CUSTOMIZE menus.
• The sound field memorized for each
input and preset station.
• All sound field parameters.
• All preset stations.
• All index names for inputs and preset
stations.
• MASTER VOLUME –/+ is set to “VOL
MIN”.
To a wall outlet
17GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 18 Friday, July 16, 2004 2:34 PM
x
5: Setting up the speakers
You can use the SET UP menu to set the size,
distance and location of the speakers connected
to this receiver.
1
2
3
Press ?/1 to turn on the receiver.
Press MAIN MENU repeatedly to select
“ SET UP ”.
Press
or
repeatedly to select the
parameter you want to adjust.
For details, see “Speaker setup parameters”
below.
Note
Some speaker setup items may appear dimmed in
the display. This means that they have been
adjusted automatically due to other speaker
settings or may not be adjustable.
4
Press + or – repeatedly to select the
setting you want.
The setting is entered automatically.
Note
Press ENTER on the receiver if you select the
setting for “SP. PAT. X–X”.
5
Repeat steps 3 and 4 until you have set
all of the items that follow.
Speaker setup parameters
The initial settings are underlined.
• YES
If you connect a sub woofer, select “YES”.
• NO
If you did not connect a sub woofer, select
“NO”. The front speakers are automatically
set to “LARGE” and you cannot change this
setting. This activates the bass redirection
circuitry and outputs the LFE signals from
other speakers.
• In order to take full advantage of the Dolby
Digital bass redirection circuitry, we
recommend that you set the cut off frequency
on the sub woofer as high as possible.
x
• EASY
If you want to set up your speakers
automatically, select “EASY SET”. You can
select a pre-defined speaker pattern (see the
supplied “Easy Setup Guide”).
• NORM
If you want to adjust the settings of each
speaker manually, select “NORM SET”.
x SP. PAT. X–X (Speaker setup pattern)
When you select “EASY SET”, select the
speaker setup pattern. Press + or – repeatedly to
select the speaker setup pattern and press
ENTER to enter the selection. Check your
speaker pattern using the supplied “Easy Setup
Guide”.
L
R
XXXXX (FRONT)
(Front speaker size)
• LARGE
If you connect large speakers that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
• SMALL
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
front channel bass frequencies from the sub
woofer. When the front speakers are set to
“SMALL”, the center and surround speakers
are also automatically set to “SMALL”
(unless previously set to “NO”).
x
x XXXX SET (Speaker easy setup)
SW
S.W. XXX (SUB WOOFER)
(Sub woofer selection)
C
XXXXX (CENTER)
(Center speaker size)
• LARGE
If you connect a large speaker that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
However, if the front speakers are set to
“SMALL”, you cannot set the center speaker
to “LARGE”.
• SMALL
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
center channel bass frequencies from the front
speakers (if set to “LARGE”) or sub woofer.a)
18GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 19 Friday, July 16, 2004 2:34 PM
x
SR
SL
XXXXX (SURROUND)
(Surround speaker size)
• LARGE
If you connect large speakers that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
However, if the front speakers are set to
“SMALL”, you cannot set the surround
speakers to “LARGE”.
• SMALL
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
surround channel bass frequencies from the
sub woofer or other “LARGE” speakers.
• NO
If you did not connect surround speakers,
select “NO”.c)
Tips
• a) – c) correspond to the following Dolby Pro Logic
modes
a) NORMAL
b) PHANTOM
c) 3 STEREO
• The “LARGE” and “SMALL” settings for each
speaker determine whether the internal sound
processor will cut the bass signal from that channel.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the sub woofer or other “LARGE”
speakers.
However, since bass sounds have a certain amount of
directionality, it is best not to cut them, if possible.
Therefore, even when using small speakers, you can
set them to “LARGE” if you want to output the bass
frequencies from that speaker. On the other hand, if
you are using a large speaker, but prefer not to have
bass frequencies output from that speaker, set it to
“SMALL”.
If the overall sound level is lower than you prefer, set
all speakers to “LARGE”. If there is not enough bass,
you can use the BASS parameter in the TONE menu
to boost the bass levels. To adjust the bass, see
page 33.
x
L
R
DIST. X.X m
(Front speaker distance)
Initial setting: 3.0 m
Lets you set the distance from your listening position
to the front speakers (A). You can adjust from 1.0
meter to 7.0 meters in 0.1 meter steps.
If both front speakers are not placed an equal distance
from your listening position, set the distance to the
closest speaker.
Getting Started
• NO
If you did not connect a center speaker, select
“NO”. The sound of the center channel will be
output from the front speakers.b)
B
A
30˚
100˚-120˚
30˚
A
100˚-120˚
C
x
C
C
DIST. X.X m
(Center speaker distance)
Initial setting: 3.0 m
Lets you set the distance from your listening position
to the center speaker. Center speaker distance should
be set from a distance equal to the front speaker
distance (A) to a distance 1.5 meters closer to your
listening position (B).
x
SR
SL
DIST. X.X m
(Surround speaker distance)
Initial setting: 3.0 m
Lets you set the distance from your listening position
to the surround speakers. Surround speaker distance
should be set from a distance equal to the front speaker
distance (A) to a distance 4.5 meters closer to your
listening position (C).
If both surround speakers are not placed an equal
distance from your listening position, set the distance
to the closest speaker.
continued
19GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB03CON_STRDE497-CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 20 Friday, July 16, 2004 2:34 PM
Tip
The receiver lets you to input the speaker position in
terms of distance. However, it is not possible to set the
center speaker further than the front speakers. Also, the
center speaker cannot be set more that 1.5 meters
closer than the front speakers.
Likewise, the surround speakers cannot be set further
away from the listening position than the front
speakers. And they can be no more than 4.5 meters
closer.
This is because incorrect speaker placement is not
conducive to the enjoyment of surround sound.
Please note that, setting the speaker distance closer than
the actual location of the speakers will cause a delay in
the output of the sound from that speaker. In other
words, the speaker will sound like it is further away.
For example, setting the center speaker distance 1–2
meters closer than the actual speaker position will
create a fairly realistic sensation of being “inside” the
screen. If you cannot obtain a satisfactory surround
effect because the surround speakers are too close,
setting the surround speaker distance closer (shorter)
than the actual distance will create a larger sound stage.
Adjusting these parameter while listening to the sound
often results in much better surround sound. Give it a
try!
x
6: Adjusting the speaker
levels and balance
— TEST TONE
Adjust the speaker levels and balance while
listening to the test tone from your listening
position. Use the remote for the operation.
Tip
The receiver employs a test tone with a frequency
centered at 800 Hz.
1
2
3
Tips
• To adjust the level of all speakers at the same
time, press MASTER VOL +/– on the remote or
turn MASTER VOLUME –/+ on the receiver.
• The adjusted value are shown in the display
during adjustment.
B
A
A
30
Adjust the speaker levels and balance
using the LEVEL menu so that the level
of the test tone sounds the same from
each speaker.
For details on the LEVEL menu settings,
see page 31.
Lets you specify the height of your surround speakers
for proper implementation of the surround effects of
the Cinema Studio EX modes (page 29).
60
Press TEST TONE.
“T. TONE” appears in the display and the
test tone is output from each speaker in
sequence.
Front (left) t Center t Front (right) t
Surround (right) t Surround (left) t
Sub woofer
SR
SL
PL. XXXX
(Surround speaker placement)*
B
Press ?/1 to turn on the receiver.
4
Press TEST TONE again after
adjustment.
The test tone turns off.
• LOW
Select if the height of your surround speakers
corresponds to section A.
• HIGH
Select if the height of your surround speakers
corresponds to section B.
* This setup item is not available when the surround
speaker size parameter is set to “NO”.
Notes
• The test tone cannot be used when MULTI CH IN
function is used.
• Although these adjustments can also be made via the
front panel using the LEVEL menu (when the test
tone is output, the receiver switches to the LEVEL
menu automatically), we recommend you follow the
procedure described above and adjust the speaker
levels from your listening position using the remote.
20GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB04BSC_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 21 Friday, July 16, 2004 2:34 PM
Amplifier Operation
Selecting the component
Press input buttons to select the input.
DVD
You can select the audio directly from the
components connected to the MULTI CH IN
jacks. This enables you to enjoy high quality
analog inputs such as DVD or Super Audio CD.
When MULTI CH IN is selected, the tone and
sound field cannot be used.
MD or tape deck
MD/TAPE
Press MULTI CH IN.
Super Audio CD or
CD player
SA-CD/CD
Press again to cancel the MULTI CH IN
function.
Built-in tuner (FM/AM)
TUNER FM/AM
To select the
Press
VCR
VIDEO 1 or
VIDEO 2
Satellite tuner
VIDEO 2
DVD player
The selected input appears in the display.
2
Turn on the component and start
playback.
Note
If you select the VCR or DVD player, set the
TV’s video input to match the component you
selected.
3
— MULTI CH IN
Amplifier Operation
1
Listening to multi channel
sound
When MULTI CHANNEL
DECODING indicator lights up
The MULTI CHANNEL DECODING indicator
lights up when the receiver is decoding multi
channel sources.
However, this indicator does not light up if you
select 2CH STEREO mode.
Turn MASTER VOLUME –/+ to adjust
the volume.
Note
To avoid damaging your speakers, make sure that
you turn down the volume before you turn off the
receiver.
To mute the sound
Press MUTING on the remote.
The muting function will be canceled when you
do the following.
• Press MUTING on the remote again.
• Turn the power off.
• Increase the volume.
To use the headphones
Connect the headphones to the PHONES jack.
When the headphones are connected, speaker
output is automatically canceled and “SP A” and
“SP B” do not light up in the display.
21GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB04BSC_STR-DE497CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 22 Friday, July 16, 2004 2:34 PM
Listening to FM/AM radio
You can listen to FM and AM broadcasts
through the built-in tuner. Before operation,
make sure you have connected the FM and AM
antennas to the receiver (see page 14).
Direct tuning
You can enter the frequency of the station you
want directly. Use the remote for the operation.
1
The last received station is tuned in.
Tip
Tip
The tuning scale differs depending on the area code as
shown in the following table. For details on area codes,
see page 3.
Area code
FM
AM
CEL, CEK, SP, TW, KR, 50 kHz
AU
9 kHz
E2/E3
9 kHz*
50 kHz
* The AM tuning scale can be changed (see page 47).
Automatic tuning
If you do not know the frequency of the station
you want, you can let the receiver scan all
available stations in your area.
1
Press TUNER FM/AM repeatedly to
select the FM or AM band.
The last received station is tuned in.
2
Press TUNER repeatedly to select the
FM or AM band.
Press TUNING + or TUNING –.
Press TUNING + to scan from low to high;
press TUNING – to scan from high to low.
The receiver stops scanning whenever a
station is received.
You can also use TUNER FM/AM on the
receiver.
2
3
Press D.TUNING.
Press the numeric buttons to enter the
frequency.
Example 1: FM 102.50 MHz
Press 1 b 0 b 2 b 5 b 0
Example 2: AM 1,350 kHz
(You do not have to enter the last “0” when
the tuning scale is set to 10 kHz.)
Press 1 b 3 b 5 b 0
If you have tuned in an AM station, adjust
the direction of the AM loop antenna for
optimum reception.
If you cannot tune in a station
and the entered numbers flash
Make sure you have entered the right frequency.
If not, repeat steps 2 and 3. If the entered
numbers still flash, the frequency is not used in
your area.
Tip
If “STEREO” flashes in the display and the FM stereo
reception is poor, press FM MODE to change to
monaural (MONO). You will not be able to enjoy the
stereo effect, but the sound will be less distorted. To
return to stereo mode, press FM MODE again.
22GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB04BSC_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 23 Friday, July 16, 2004 2:34 PM
Storing FM stations
automatically
— AUTOBETICAL
Presetting radio stations
(Models of area code CEL, CEK only)
This function lets you store up to 30 FM and FM
RDS stations in alphabetical order without
redundancy. Additionally, it only stores the
stations with the clearest signals.
If you want to store FM or AM stations one by
one, see “Presetting radio stations”.
1
2
Presetting radio stations
1
The last received station is tuned in.
2
Press ?/1 to turn off the receiver.
Hold down MEMORY and press ?/1 to
turn the receiver back on.
“AUTO-BETICAL SELECT” appears in
the display and the receiver scans and stores
all the FM and FM RDS stations in the
broadcast area.
For RDS stations, the tuner first checks for
stations broadcasting the same program,
then stores only the one with the clearest
signal. The selected RDS stations are sorted
alphabetically by their Program Service
name, then assigned a 2-character preset
code. For more details on RDS, see
page 24.
Regular FM stations are assigned 2character preset codes and stored after the
RDS station.
When done, “FINISH” appears in the
display momentarily and the receiver
returns to the normal operation.
3
Tune in the station that you want to
preset using Automatic Tuning
(page 22) or Direct Tuning (page 22).
Press MEMORY.
“MEMORY” appears in the display for a
few seconds. Do steps 4 to 5 before the
display goes out.
4
Press PRESET TUNING + or PRESET
TUNING – repeatedly to select a preset
station number.
Each time you press the button, you can
select the preset station number as follows:
tA1yA2y...yA0yB1yB2y...yB0T
tC0y...yC2yC1T
If “MEMORY” goes out before you select
the preset station number, start again from
step 3.
Tip
You can also use the remote to select a preset
station number. Press SHIFT repeatedly to select
a memory page (A, B or C) and then press the
numeric buttons to select a preset number.
Notes
• Do not press any button on the receiver or supplied
remote during autobetical operation, except ?/1.
• If you move to another area, repeat this procedure to
store stations in your new area.
• For details on tuning the stored stations, see “Tuning
to preset stations”.
• If you move the antenna after storing stations with
this procedure, the stored settings may no longer be
valid. If this happens, repeat this procedure to store
the stations again.
Press TUNER FM/AM repeatedly to
select the FM or AM band.
Amplifier Operation
You can preset up to 30 FM or AM stations.
Then you can easily tune in the stations you
often listen to.
5
Press MEMORY again.
The station is stored to the selected preset
number.
If “MEMORY” goes out before you press
MEMORY, start again from step 3.
6
Repeat steps 2 to 5 to preset another
station.
continued
23GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB04BSC_STR-DE497CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 24 Friday, July 16, 2004 2:34 PM
Tuning to preset stations
1
Press TUNER FM/AM repeatedly to
select the FM or AM band.
The last received station is tuned in.
2
Press PRESET TUNING + or PRESET
TUNING – repeatedly to select the
preset station you want.
Each time you press the button, you can
select the preset station as follows:
tA1yA2y...yA0yB1yB2y...yB0T
tC0y...yC2yC1T
Using the remote
1 Press TUNER repeatedly to select the FM or
AM band.
2 Press CH/PRESET –/+ repeatedly to select
the preset station you want.
To select the preset station
directly
Press the numeric buttons on the remote.
The preset station of the selected number in the
current memory page is tuned in. Press SHIFT
repeatedly on the remote to change the memory
page.
Using the Radio Data
System (RDS)
(Models of area code CEL, CEK only)
This receiver also allows you to use RDS (Radio
Data System), which enables radio stations to
send additional information along with the
regular program signal. You can also display
RDS information.
Notes
• RDS is operable only for FM stations.
• Not all FM stations provide RDS service, nor do they
provide the same types of services. If you are not
familiar with the RDS services in your area, check
with your local radio stations for details.
Receiving RDS broadcasts
Simply select a station on the FM band
using automatic tuning (page 22), direct
tuning (page 22), or preset tuning
(page 24).
When you tune in a station that provides RDS
services, the RDS indicator lights up and the
program service name appears in the display.
Note
RDS may not work properly if the station you tuned to
is not transmitting the RDS signal properly or if the
signal strength is weak.
24GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB04BSC_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 25 Friday, July 16, 2004 2:34 PM
Program type
indication
Description
While receiving an RDS station, press
DISPLAY repeatedly.
LIGHT M
Instrumental, vocal, and choral
music
Each time you press the button, RDS
information on the display changes cyclically as
follows:
Program Service name t Frequency t
Program Type indicationa) t Radio Text
indicationb) t Current Time indication (in 24hour system) t Sound field currently applied
CLASSICS
Performances of major orchestras,
chamber music, opera, etc.
OTHER M
Music that does not fit into any
categories above, such as Rhythm
& Blues and Reggae
WEATHER
Weather information
FINANCE
Stock market reports and trading,
etc.
CHILDREN
Programs for children
SOCIAL
Programs about people and the
things that affect them
RELIGION
Programs of religious content
PHONE IN
Programs where members of the
public express their views by
phone or in a public forum
TRAVEL
Programs about travel. Not for
announcements that are located by
TP/TA
LEISURE
Programs on recreational
activities such as gardening,
fishing, cooking, etc.
JAZZ
Jazz programs
COUNTRY
Country music programs
NATION M
Programs featuring the popular
music of the country or region
OLDIES
Programs featuring oldies music
FOLK M
Folk music programs
DOCUMENT
Investigative features
NONE
Any programs not defined above
a)
b)
Type of program being broadcast (see page 25).
Text messages sent by the RDS station.
Notes
• If there is an emergency announcement by
government authorities, “ALARM” flashes in the
display.
• When the message consists of 9 characters or more,
the message scrolls across the display.
• If a station does not provide a particular RDS service,
“NO XXXX” (such as “NO TEXT”) appears in the
display.
Description of program types
Program type
indication
Description
NEWS
News programs
AFFAIRS
Topical programs that expand on
current news
INFO
Programs offering information on
a wide spectrum of subjects,
including consumer affairs and
medical advice
SPORT
Sports programs
EDUCATE
Educational programs, such as
“how-to” and advice programs
DRAMA
Radio plays and serials
CULTURE
Programs about national or
regional culture, such as language
and social concerns
SCIENCE
Programs about the natural
sciences and technology
VARIED
Other types of programs such as
celebrity interviews, panel games,
and comedy
POP M
Popular music programs
ROCK M
Rock music programs
EASY M
Easy Listening
Amplifier Operation
Displaying RDS information
25GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB04BSC_STR-DE497CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 26 Friday, July 16, 2004 2:34 PM
Changing the display
Changing the information in
the display
You can check the sound field etc. by changing
the information in the display.
Press DISPLAY repeatedly.
Each time you press DISPLAY, the display will
change cyclically as follows.
Index name of the input* t Selected input t
Sound field currently applied
When the tuner is selected
Program Service name** or preset station name*
t Frequency t Program Type indication**
t Radio Text indication** t Current Time
indication (in 24-hour system)** t Sound field
currently applied.
* Index name appears only when you have assigned
one to the input or preset station (page 35). Index
name does not appear when only blank spaces have
been entered, or it is the same as the input name.
** During RDS reception only. (Models of area code
CEL, CEK only. See page 25).
Adjusting the brightness of
the display
Press DIMMER repeatedly.
The brightness of the display will change in 3
steps.
26GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB04BSC_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 27 Friday, July 16, 2004 2:34 PM
About the indications in the display
1
2
3
4
5
6
RDS MEMORY
STEREO MONO
SW
qs
qa
D.RANGE
0 9
A SW: Lights up when sub woofer selection is
set to “YES” (page 18) and audio signal is
output from the SUB WOOFER jack.
B LFE: Lights up when the disc being played
back contains the LFE (Low Frequency
Effect) channel and the LFE channel signal is
actually being reproduced.
C SP A/SP B: Lights up in accordance with the
speaker system being used (A or B). Turns off
when speaker output is turned off or when
headphones are connected.
D ; DIGITAL: Lights up when the receiver is
decoding signals recorded in the Dolby Digital
format.
E ; PRO LOGIC II: “; PRO LOGIC” lights
up when the receiver applies Pro Logic
processing to 2 channel signals in order to
output the center and surround channel
signals. “; PRO LOGIC II” lights up when
the Pro Logic II Movie/Music decoder is
activated. However, both indicators do not
light up if both the center and surround
speakers are set to “NO” and “A.F.D. AUTO”,
“DOLBY PL”, “PLII MOV” or “PLII MUS”
is selected.
Note
Dolby Pro Logic and Dolby Pro Logic II
decoding do not function for DTS format signals.
F DTS: Lights up when DTS signals are input.
Note
When playing a DTS format disc, be sure that you
have made digital connections and that INPUT
MODE is not set to “ANALOG” (page 31).
8
G Tuner indicators: Lights up when using the
receiver to tune in radio stations, etc. See
pages 22–25 for tuner operations.
Amplifier Operation
L F E SP A ; DIGITAL ;PRO LOGIC II DTS
SP B SLEEP OPT COAX
L C R
SL S SR
7
Note
“RDS” appears for models of area code CEL,
CEK only.
H D.RANGE: Lights up when dynamic range
compression is activated (page 32).
I COAX: Lights up when the source signal is a
digital signal being input through the
COAXIAL terminal.
J OPT: Lights up when the source signal is a
digital signal being input through the
OPTICAL terminal.
K SLEEP: Lights up when sleep timer is
activated.
L Playback channel indicators: The letters
(L, C, R, etc.) indicate the channels being
played back. The boxes around the letters vary
to show how the receiver downmixes the
source sound (based on the speakers settings).
L (Front Left), R (Front Right), C (Center
(monaural)), SL (Surround Left), SR
(Surround Right), S (Surround (monaural or
the surround components obtained by Pro
Logic processing))
Example:
Recording format (Front /Surround): 3/2
Output channel: Surround speakers absent
Sound Field: A.F.D. AUTO
L
SL
C
R
SR
27GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB05SND_STR-DE497CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 28 Friday, July 16, 2004 2:34 PM
Enjoying Surround Sound
Using only the front
speakers
In this mode, the receiver outputs the sound
from the front left/right speakers only. There is
no sound from the sub woofer.
Listening to 2 channel stereo
sources (2CH STEREO)
Standard 2 channel stereo sources completely
bypass the sound field processing and multi
channel surround formats are downmixed to 2
channel.
Press 2CH.
“2CH ST.” appears in the display and the
receiver switches to the 2CH STEREO mode.
Note
No sound is output from the sub woofer in the 2CH
STEREO mode. To listen to the 2 channel stereo
sources using the front left/right speakers and a sub
woofer, set to the A.F.D. mode.
Enjoying higher fidelity
sound
— AUTO FORMAT DIRECT
The Auto Format Direct (A.F.D.) mode allows
you to select the decoding mode you want for
your audio sound.
A.F.D. mode
(Display)
Decoding mode
A.F.D. AUTO
(A.F.D. AUTO)
As encoded
PRO LOGIC
(DOLBY PL)
Dolby Pro Logic
PRO LOGIC II MOVIE
(PLII MOV)
Dolby Pro Logic II
PRO LOGIC II MUSIC
(PLII MUS)
Decoding the input audio
signal automatically
In this mode, the receiver automatically detects
the type of audio signal being input (Dolby
Digital, DTS, standard 2 channel stereo, etc.)
and performs the proper decoding if necessary.
This mode presents the sound as it was recorded/
encoded, without adding any surround effects.
However, if there are no low frequency signals
(Dolby Digital LFE, etc.) it will generate a low
frequency signal for output to the sub woofer.
Press A.F.D. repeatedly to select “A.F.D.
AUTO”.
The receiver automatically detects the type of
audio signal being input and performs the proper
decoding if necessary.
28GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB05SND_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 29 Friday, July 16, 2004 2:34 PM
Enjoying stereo sound in multi
channel (2 channel decoding
mode)
You can take advantage of surround sound
simply by selecting one of the receiver’s preprogrammed sound fields. They bring the
exciting and powerful sound of movie theaters
and concert halls into your home.
Press A.F.D. repeatedly to select the 2
channel decoding mode.
Selecting a sound field for
movies
The selected type of decoding appears in the
display.
Press MOVIE repeatedly to select the
sound field you want.
x DOLBY PL (PRO LOGIC)
The selected sound field appears in the display.
Performs Dolby Pro Logic decoding. The source
recorded in 2 channel is decoded into 4.1 channels.
Sound field
Display
CINEMA STUDIO EX A DCS
C.ST.EX A
CINEMA STUDIO EX B DCS
C.ST.EX B
CINEMA STUDIO EX C DCS
C.ST.EX C
x PLII MOV (PRO LOGIC II MOVIE)
Performs Dolby Pro Logic II Movie mode decoding.
This setting is ideal for movies encoded in Dolby
Surround. In addition, this mode can reproduce sound
in 5.1 channel when watching videos of overdubbed or
old movies.
x PLII MUS (PRO LOGIC II MUSIC)
Performs Dolby Pro Logic II Music mode decoding.
This setting is ideal for normal stereo sources such as
CDs.
Note
Dolby Pro Logic and Dolby Pro Logic II decoding does
not function for DTS format signals.
If you connect a sub woofer
When the audio signal is 2 channel stereo or if
the source signal does not include a LFE signal,
the receiver generates a low frequency signal for
output to the sub woofer.
Enjoying Surround Sound
This mode lets you specify the type of decoding
for 2 channel audio sources. This receiver can
reproduce 2 channel sound in 5 channels
through Dolby Pro Logic II or 4 channels
through Dolby Pro Logic.
Selecting a sound field
About DCS (Digital Cinema
Sound)
Sound fields with DCS marks use DCS
technology.
DCS is the concept name of the surround
technology for home theater developed by Sony.
DCS uses the DSP (Digital Signal Processor)
technology to reproduce the sound
characteristics of an actual cinema cutting studio
in Hollywood.
When played at home, DCS will create a
powerful theater effect that mimics the artistic
combination of sound and action as envisioned
by the movie director.
x C.ST.EX A (CINEMA STUDIO EX A) DCS
Reproduces the sound characteristics of the Sony
Pictures Entertainment “Cary Grant Theater” cinema
production studio. This is a standard mode, great for
watching most any type of movies.
x C.ST.EX B (CINEMA STUDIO EX B) DCS
Reproduces the sound characteristics of the Sony
Pictures Entertainment “Kim Novak Theater” cinema
production studio. This mode is ideal for watching
science-fiction or action movies with lots of sound
effects.
continued
29GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB05SND_STR-DE497CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 30 Friday, July 16, 2004 2:34 PM
x C.ST.EX C (CINEMA STUDIO EX C) DCS
Reproduces the sound characteristics of the Sony
Pictures Entertainment scoring stage. This mode is
ideal for watching musicals or films where orchestra
music is featured in the soundtrack.
About CINEMA STUDIO EX modes
CINEMA STUDIO EX modes are suitable for
watching motion picture DVDs (etc.), with
multi channel surround effects. You can
reproduce the sound characteristics of Sony
Pictures Entertainment’s dubbing studio in your
home.
The CINEMA STUDIO EX modes consist of
the following three elements.
• Virtual Multi Dimension
Creates 5 sets of virtual speakers from a single
pair of actual surround speakers.
• Screen Depth Matching
Creates the sensation that the sound is coming
from inside the screen like in theaters.
• Cinema Studio Reverberation
Reproduces the type of reverberation found in
theaters.
The CINEMA STUDIO EX modes integrate
these three elements simultaneously.
Notes
• The effects provided by the virtual speakers may
cause increased noise in the playback signal.
• When listening with sound fields that employ the
virtual speakers, you will not be able to hear any
sound coming directly from the surround speakers.
Selecting a sound field for
music
Press MUSIC repeatedly to select the
sound field you want.
The selected sound field appears in the display.
Sound field
Display
HALL
HALL
JAZZ CLUB
JAZZ
LIVE CONCERT
CONCERT
x HALL
Reproduces the acoustics of a classical concert hall.
x JAZZ (JAZZ CLUB)
Reproduces the acoustics of a jazz club.
x CONCERT (LIVE CONCERT)
Reproduces the acoustics of a 300-seat live house.
To turn off the surround effect
Press 2CH to select “2CH ST.” or press A.F.D.
repeatedly to select “A.F.D. AUTO”.
Tips
• The receiver lets you apply the last selected sound
field to an input whenever it is selected (Sound Field
Link). For example, if you select HALL for the
SA-CD/CD input, then change to a different input
and then return to SA-CD/CD, HALL will
automatically be applied again.
• You can identify the encoding format of DVD
software, etc. by looking at the logo on the package.
–
: Dolby Digital discs
–
: Dolby Surround encoded
programs
–
: DTS Digital Surround encoded programs
Notes
• Sound fields do not function for the signals with a
sampling frequency of more than 48 kHz.
• When one of the following sound fields are selected,
no sound is output from the sub woofer if all the
speakers are set to “LARGE” in the SET UP menu.
However, the sound will be output from the sub
woofer if the digital input signal contains LFE (Low
Frequency Effect) signals, or if the front, center, or
surround speakers are set to “SMALL”.
– HALL
– JAZZ CLUB
– LIVE CONCERT
30GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB06ADV_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 31 Friday, July 16, 2004 2:34 PM
Advanced Adjustments and Settings
Switching the audio input
mode for digital
components
— INPUT MODE
1
2
Press input buttons to select the input.
Press INPUT MODE repeatedly to
select the audio input mode.
The selected audio input mode appears in
the display.
Audio input modes
• AUTO IN
Gives priority to digital signals when there are
both digital and analog connections. If there
are no digital signals, analog is selected.
• COAX IN
Specifies the digital audio signals input to the
DIGITAL COAXIAL input jack.
• OPT IN
Specifies the digital audio signals input to the
DIGITAL OPTICAL input jacks.
• ANALOG
Specifies the analog audio signals input to the
AUDIO IN (L/R) jacks.
Note
When signals with a sampling frequency of more than
48 kHz is input, the tone and sound field cannot be
used.
By adjusting the LEVEL menu, you can
customize the sound fields to suit your particular
listening situation.
Note on the displayed items
The setup items you can adjust in each menu vary
depending on the sound field. Certain setup parameters
may be dimmed in the display. This means that the
selected parameter is either unavailable or fixed and
unchangeable.
Adjusting the LEVEL menu
You can adjust the balance and level of each
speaker. These settings are applied to all sound
fields except for the effect level parameter. The
effect level parameter settings are stored
individually for each sound field.
1
2
3
Start playing a source encoded with
multi channel surround effects (DVD,
etc.).
Press MAIN MENU repeatedly to select
“ LEVEL ”.
Advanced Adjustments and Settings
You can switch the audio input mode for
components which have digital audio input
jacks.
Customizing sound fields
Press
or
repeatedly to select the
parameter you want to adjust.
For details, see “LEVEL menu parameters”
below.
4
While monitoring the sound, press + or
– repeatedly to select the setting you
want.
The setting is entered automatically.
5
Repeat steps 3 and 4 to adjust the other
parameters.
LEVEL menu parameters
The initial setting is underlined.
x
L
R
BAL. L/R XX
(Front speaker balance)
Initial setting: BALANCE (0)
Lets you adjust the balance between front left and right
speakers. You can adjust in the range of BAL. L (+1 to
+8), BALANCE (0), BAL. R (+1 to +8) in 17 steps.
continued
31GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB06ADV_STR-DE497CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 32 Friday, July 16, 2004 2:34 PM
x CTR XXX dB
(Center speaker level)
x SUR.L. XXX dB
(Surround speaker (left) level)
x SUR.R. XXX dB
(Surround speaker (right) level)
x S.W. XXX dB
(Sub woofer level)
Initial setting: 0 dB
You can adjust from –10 dB to +10 dB in 1 dB steps.
x
Resetting sound fields to the
initial settings
Use the buttons on the receiver for the operation.
1
2
Press ?/1 to turn off the power.
While holding down 2CH, press
?/1.
“SF. CLR.” appears in the display and all
sound fields are reset to the initial setting.
D.RANGE
COMP. XXX
(Dynamic range compressor)
Lets you compress the dynamic range of the sound
track. This may be useful when you want to watch
movies at low volumes late at night.
• OFF
The dynamic range is not compressed.
• STD
The dynamic range is compressed as intended by the
recording engineer.
• MAX
The dynamic range is compressed dramatically.
Tip
Dynamic range compressor lets you compress the
dynamic range of the soundtrack based on the dynamic
range information included in the Dolby Digital signal.
We recommend using the “MAX” setting. This greatly
compresses the dynamic range and lets you view
movies late at night at low volumes. Unlike analog
limiters, the levels are predetermined and provide a
very natural compression.
Note
Dynamic range compression is possible with Dolby
Digital sources only.
x EFCT. XXX (Effect level)
Initial setting: STD
Lets you adjust the “presence” of the surround effect.
32GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB06ADV_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 33 Friday, July 16, 2004 2:34 PM
Adjusting the tone
You can adjust the tonal quality (bass, treble
level) of the front speakers using the TONE
menu.
1
3
Press MAIN MENU repeatedly to select
“ TONE ”.
5
You can adjust various receiver settings using
the CUSTOMIZE menu.
1
2
Press
or
repeatedly to select the
parameter you want to adjust.
For details, see “TONE menu parameters”
below.
4
Using the CUSTOMIZE menu
to adjust the receiver
While monitoring the sound, press + or
– repeatedly to select the setting you
want.
Press MAIN MENU repeatedly to select
“ CUSTOM ”.
Press
or
repeatedly to select the
parameter you want to adjust.
For details, see “CUSTOMIZE menu
parameters” below.
3
Press + or – repeatedly to select the
setting you want.
The setting is entered automatically.
The setting is entered automatically.
4
Repeat steps 3 and 4 to adjust the other
items.
CUSTOMIZE menu parameters
Repeat steps 2 and 3 to adjust the other
items.
Note
The initial setting is underlined.
You cannot adjust the tone when the receiver is
decoding signals with a sampling frequency of more
than 48 kHz.
x DEC. XXXX
(Digital audio input decoding priority)
TONE menu parameters
x BASS XX dB
(Front speaker bass level)
x TREB. XX dB
(Front speaker treble level)
Initial setting: 0 dB
You can adjust from –6 dB to +6 dB in 1 dB steps.
Advanced Adjustments and Settings
2
Start playing a source encoded with
multi channel surround effects (DVD,
etc.).
Advanced settings
Lets you specify the input mode for the digital signal
input to the DIGITAL IN jacks.
The initial setting is “DEC. AUTO” for VIDEO 2 and
“DEC. PCM” for DVD and SA-CD/CD.
• AUTO
Automatically switches the input mode between
DTS, Dolby Digital, or PCM.
• PCM
PCM signals are given priority (to prevent the
interruption when playback starts). Even when other
signals are input, the sound is output. However, this
receiver cannot decode DTS-CD when set to “DEC.
PCM”.
Note
When set to “DEC. AUTO” and the sound from the
digital audio jacks (for CD, etc.) is interrupted when
playback starts, set to “DEC. PCM”.
continued
33GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB06ADV_STR-DE497CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 34 Friday, July 16, 2004 2:34 PM
x DUAL XXX
(Digital broadcast language selection)
Lets you select the language you want to listen to
during digital broadcast. This feature only functions
for Dolby Digital sources.
• M/S (Main/Sub)
Sound of the main language will be output through
the front left speaker and sound of the sub language
will be output through the front right speaker
simultaneously.
• M (Main)
Sound of the main language will be output.
• S (Sub)
Sound of the sub language will be output.
• M+S (Main + Sub)
Mixed sound of both the main and sub languages will
be output.
x NAME IN
(Naming preset stations and inputs)
Lets you set the name of preset stations and inputs
selected with input buttons. For details, see “Naming
preset stations and inputs” on page 35.
34GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB070TH_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 35 Friday, July 16, 2004 2:34 PM
Tips
• You can select the character type as follows by
pressing + or – repeatedly.
Alphabet (upper case) t Numbers t Symbols
• To enter a blank space, press + or – repeatedly
until a blank space appears in the display.
• If you made a mistake, press or repeatedly
until the character you want to change flashes,
then press + or – repeatedly to select the correct
character.
Other Operations
Naming preset stations
and inputs
You can enter a name of up to 8 characters for
preset stations and inputs selected with input
buttons, and display it in the receiver’s display.
Use the buttons on the receiver for the operation.
1
To index a preset station
Press ENTER to store the index name.
Note (Models of area code CEL, CEK only)
When you name an RDS station and tune in the station,
the Program Service name appears instead of the name
you entered. (You cannot change the name of a
Program Service name. The name you entered will be
overwritten by the Program Service name.)
To index an input
Press the input button to select the
input you want to create an index name
for.
2
3
4
Other Operations
Press TUNER FM/AM repeatedly to
select the FM or AM band, then tune in
the preset station you want to create an
index name for (page 24).
6
Press MAIN MENU repeatedly to select
“ CUSTOM ”.
Press
or
“NAME IN”.
repeatedly to select
Press ENTER.
The cursor flashes and you can select a
character.
5
Use
or
and + or – to create an
index name.
Press + or – repeatedly to select a character,
then press to move the cursor to the next
position.
35GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB070TH_STR-DE497CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 36 Friday, July 16, 2004 2:34 PM
Using the Sleep Timer
You can set the receiver to turn off automatically
at a specified time. Use the remote for the
operation.
Press SLEEP repeatedly while the power is
on.
Each time you press SLEEP, the display changes
cyclically as follows:
2-00-00 t 1-30-00 t 1-00-00 t 0-30-00 t
OFF
While using Sleep Timer, “SLEEP” lights up in
the display.
Selecting the speaker
system
You can select the front speaker system you
want to use.
Press SPEAKERS (OFF/A/B/A+B)
repeatedly to select the front speaker
system you want to use.
The selected speaker system appears in the
display. To turn off the speaker output, press
SPEAKERS (OFF/A/B/A+B) repeatedly until
“SP A” and “SP B” indication turn off.
Tip
The speaker system
To check the remaining time before the receiver turns
off, press SLEEP. The remaining time appears in the
display. If you press SLEEP again, the sleep timer will
be canceled.
• SP A
The speakers connected to the SPEAKERS
FRONT A terminals.
• SP B
The speakers connected to the SPEAKERS
FRONT B terminals.
• SP A and SP B
The speakers connected to both the
SPEAKERS FRONT A and B terminals
(parallel connection).
36GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB070TH_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 37 Friday, July 16, 2004 2:34 PM
Recording
Before you begin, make sure you have
connected all components properly.
Recording on an audio tape or
MiniDisc
Recording on a video tape
You can record from a VCR, a TV or a DVD
using the receiver. You can also add audio from
a variety of audio sources when editing a video
tape. See the operating instructions of your VCR
or DVD player if you need help.
1
You can record on a cassette tape or MiniDisc
using the receiver. See the operating instructions
of your cassette deck or MD deck if you need
help.
2
1
2
3
Prepare the component for playing.
For example, insert a CD into the CD
player.
3
4
Insert a blank tape or MD into the
recording deck and adjust the
recording level, if necessary.
Start recording on the recording deck,
then start playback on the playback
component.
Notes
• Sound adjustments do not affect the signal output
from the MD/TAPE OUT jacks.
• The analog audio signals of the current input is
output from the MD/TAPE OUT jacks.
• The signals input to the MULTI CH IN jacks are not
output from the MD/TAPE OUT jacks even when
MULTI CH IN is being used. The analog audio
signals of the current or previously used input are
output.
• Some sources contain copy guards to prevent
recording. In this case, you may not be able to record
from the sources.
Prepare the component for playing.
For example, insert a video tape you want to
record into VCR.
4
Insert a blank video tape into the VCR
(VIDEO 1) for recording.
Start recording on the recording VCR,
then start playing the video tape or
DVD you want to record.
Tip
Other Operations
Select the component to be recorded.
Select the program source to be
recorded.
You can record the sound from any audio source onto
a video tape while copying from a video tape or DVD.
Locate the point where you want to start recording
from another audio source, select the program source,
then start playback. The audio from that source will be
recorded onto the audio track of the video tape instead
of the audio from the original medium. To resume
audio recording from the original medium, select the
video source again.
Notes
• You cannot record a digital audio signal using a
component connected to the analog VIDEO 1 OUT
jacks.
• Make sure to make both digital and analog
connections to the VIDEO 2 and DVD inputs.
Analog recording is not possible if you make only
digital connections.
• The analog audio signals of the current input are
output from the VIDEO 1 OUT jacks.
• The signals input to the MULTI CH IN jacks are not
output from VIDEO 1 OUT jacks even when MULTI
CH IN is being used. The analog audio signals of the
current or previously used input are output.
37GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB08REM_STRDE497-CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 38 Friday, July 16, 2004 2:34 PM
Operations Using the Remote RM-U306B
You can use the remote RM-U306B to operate
the components in your system.
Remote button
description
Before you use your
remote
AV
?/1
SLEEP
?/1
ea
e;
1
Inserting batteries into the
remote
Insert R6 (size-AA) batteries with the + and –
properly oriented in the battery compartment.
When using the remote, point it at the remote
sensor
on the receiver.
SYSTEM
STANDBY
2
VIDEO 1
VIDEO 2
DVD
MD/TAPE
SA-CD
TUNER
3
4
TOP MENU
V
1
DVD MENU
2
B
3
b
ENTER
4
5
6
8
SHIFT
wh
O
v
7
wl
wk
wj
9
D.TUNING
0
5
>10
6
– CH/PRESET +
.
>
-
ENTER
wg
RETURN
TV/VIDEO
wf
ANT
TV/VTR
Tip
Under normal conditions, the batteries should last for
about 6 months. When the remote no longer operates
the receiver, replace all batteries with new ones.
7
m
8
9
q;
N
X
x
2CH
A.F.D.
MOVIE/
MUSIC
Notes
• Do not leave the remote in an extremely hot or humid
place.
• Do not use a new battery with an old one.
• Do not expose the remote sensor to direct sunlight or
lighting apparatuses. Doing so may cause a
malfunction.
• If you don’t use the remote for an extended period of
time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
M
TEST TONE
MAIN MENU
D.SKIP
MULTI CH
qa
MENU
wd
ws
wa
w;
ql
qk
MUTING
qs
qj
MASTER
VOL
qd
qh
qf
TV VOL
TV CH
qg
The tables below show the settings of each
button.
Remote
Button
Operations
A.F.D. 9 Receiver
Function
Selects the decoding
mode for audio sound.
38GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB08REM_STRDE497-CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 39 Friday, July 16, 2004 2:34 PM
Remote
Button
Operations
Function
Remote
Button
Operations
Function
ANT
TV/VTR
wd
VCR
Selects output signal
from the antenna
terminal: TV signal or
VCR program.
MENU </> Receiver
qs
Selects a menu item.
MENU –/+ Receiver
qd
Adjusts or changes the
setting.
AV ?/1
ea
TV/VCR/
Turns the audio and
CD player/
video components on or
VCD player/ off.
LD player/
DVD player/
MD deck/
DAT deck
MOVIE/
Receiver
MUSIC w;
Selects the preprogrammed sound
fields for movie and
music.
MULTI CH Receiver
qk
Selects MULTI CH IN
source.
Receiver
Selects preset stations.
MUTING
qj
Receiver
Mutes the sound from
the receiver.
–/+ 6
TV/VCR/
Selects preset channel.
Satellite tuner
RETURN
wg
VCD player
Returns to the previous
menu.
D.SKIP wd CD player/
Skips discs (multi-disc
VCD player/ changer only).
DVD player/
MD deck
D.TUNING Receiver
wg
Enters direct tuning
mode.
DVD wl
Receiver
To watch DVD.
DVD
MENU wh
DVD player
Displays DVD menu.
ENTER wg TV/VCR/
Satellite tuner/
LD player/
MD deck/
DAT deck/
Tape deck
After selecting a
channel, disc or track
using the numeric
buttons, press to enter
the value.
ENTER wh DVD player
Enters the selection.
MAIN
MENU ql
Receiver
Selects the menu of the
receiver.
MASTER
VOL +/–
qh
Receiver
Adjusts the master
volume of the receiver.
MD/TAPE
4
Receiver
To listen to Minidisc or
audio tape.
SA-CD wk Receiver
To listen to Super Audio
CD or compact disc.
SHIFT 5
Selects a memory page
for presetting radio
stations or tuning to
preset stations.
Receiver
SLEEP 1 Receiver
Activates the sleep
function and the
duration which the
receiver turns off
automatically.
SYSTEM
STANDBY
(Press AV
?/1 ea and
?/1 e; at
the same
time)
Receiver/TV/ Turns off the receiver
VCR/Satellite and other Sony audio/
tuner/
video components.
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck
TEST
TONE qa
Receiver
TOP
DVD player
MENU wh
Operations Using the Remote RM-U306B
CH/
PRESET
Outputs test tone.
Displays DVD title.
continued
39GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB08REM_STRDE497-CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 40 Friday, July 16, 2004 2:34 PM
Remote
Button
Operations
Function
Remote
Button
TUNER wj Receiver
To listen to radio
programs.
TV CH
+/– qg
TV
Selects preset TV
channels.
TV/VIDEO
wf
TV
Selects input signal:
TV input or video
input.
./> VCR/
Skips tracks.
6
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck/
Tape deck
TV VOL
+/– qf
TV
Adjusts the volume of
the TV.
m/M
7
VIDEO 1 3 Receiver
To watch VCR.
(VTR mode 3)
VIDEO 2 2 Receiver
To watch VCR.
(VTR mode 1)
0-9 wh
Use with SHIFT to
preset radio station or
tuning to preset stations
and with D.TUNING
for direct tuning.
Receiver
CD player/
Selects track numbers.
VCD player/ 0 selects track 10.
LD player/
MD deck/
DAT deck
Receiver
>10 5
CD player/
Selects track numbers
VCD player/ over 10.
LD player/
MD deck
TV
Selects the channel
entry mode, either one
or two digit.
?/1 e;
Receiver
Turns the receiver on or
off.
CD player/
VCD player/
DVD player
Searches tracks in the
forward or backward
direction.
VCR/
LD player/
MD deck/
DAT deck/
Tape deck
Fastforwards or
rewinds.
Starts playback.
VCR/
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck/
Tape deck
X ws
VCR/
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck/
Tape deck
x wa
VCR/
Stops playback.
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck/
Tape deck
Selects 2CH STEREO
mode.
-/-- 5
Function
N8
TV/VCR/
Selects channel
Satellite tuner numbers.
2CH q;
Operations
Pauses playback or
recording. (Also starts
recording with
components in
recording standby.)
40GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB08REM_STRDE497-CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 41 Friday, July 16, 2004 2:34 PM
Remote
Button
Operations
Function
O wh
DVD player
Returns to the previous
menu or exits the menu.
V/v/B/b
wh
DVD player
Selects a menu item.
Notes
If the factory settings of the input buttons do not
match your system components, you can change
them. For example, if you have a tape deck and
you do not have an MD deck, you can assign the
MD/TAPE button to your tape deck.
Note that the settings of the TUNER button
cannot be changed.
1
2
Hold down the input button whose input
you want to change (for example, MD/
TAPE).
Press the corresponding button of the
component you want to assign to the
input button (for example, 4 – Tape deck).
The following buttons are assigned to select
the input:
To operate
Press
CD player
1
DAT deck
2
MD deck
3
Tape deck A
4
Tape deck B
5
LD player
6
VCR (command mode VTR 1*)
7
VCR (command mode VTR 2*)
8
VCR (command mode VTR 3*)
9
TV
0
DSS (Digital Satellite Receiver)
Operations Using the Remote RM-U306B
• When you press the input buttons (VIDEO 1, VIDEO
2, DVD), the input mode of the TV might not switch
to the corresponding input mode that you want. In
this case, press the TV/VIDEO button to switch the
input mode of the TV.
• Some functions explained in this section may not
work depending on the model of the receiver.
• The above explanation is intended to serve as an
example only. Therefore, depending on the
component the above operation may not be possible
or may operate differently than described.
Changing the factory
setting of an input button
>10
DVD player
ENTER
VCD player
.
*Sony VCRs are operated with a VTR 1, 2 or 3
setting. These correspond to Beta, 8mm and
VHS respectively.
Now you can use the MD/TAPE button to
control the tape deck.
To reset a button to its factory
setting
Repeat the above procedure.
To reset all the input buttons to
their factory setting
Press ?/1, AV ?/1 and MASTER VOL – at the
same time.
41GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB09ADD_STR-DE497CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 42 Friday, July 16, 2004 2:34 PM
On cleaning
Additional Information
Precautions
On safety
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
If you have any question or problem concerning your
receiver, please consult your nearest Sony dealer.
Should any solid object or liquid fall into the cabinet,
unplug the receiver and have it checked by qualified
personnel before operating it any further.
On power sources
• Before operating the receiver, check that the
operating voltage is identical with your local power
supply. The operating voltage is indicated on the
nameplate at the rear of the receiver.
• The receiver is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the receiver itself has been turned off.
• If you are not going to use the receiver for a long
time, be sure to disconnect the receiver from the wall
outlet. To disconnect the AC power cord, grasp the
plug itself; never pull the cord.
• AC power cord must be changed only at the qualified
service shop.
On heat buildup
Although the receiver heats up during operation, this is
not a malfunction. If you continuously use this receiver
at a large volume, the cabinet temperature of the top,
side and bottom rises considerably. To avoid burning
yourself, do not touch the cabinet.
On placement
• Place the receiver in a location with adequate
ventilation to prevent heat buildup and prolong the
life of the receiver.
• Do not place the receiver near heat sources, or in a
place subject to direct sunlight, excessive dust or
mechanical shock.
• Do not place anything on top of the cabinet that
might block the ventilation holes and cause
malfunctions.
• Use caution when placing the receiver on surfaces
that have been specially treated (with wax, oil,
polish, etc.) as staining or discoloration of the surface
may result.
On operation
Before connecting other components, be sure to turn
off and unplug the receiver.
42GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB09ADD_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 43 Friday, July 16, 2004 2:34 PM
Troubleshooting
If you experience any of the following
difficulties while using the receiver, use this
troubleshooting guide to help you remedy the
problem.
There is no sound from a specific component.
• Check that the component is connected correctly
to the audio input jacks for that component.
• Check that the cord(s) used for the connection is
(are) fully inserted into the jacks on both the
receiver and the component.
• Check that you have selected the correct
component on the receiver.
There is no sound from one of the front
speakers.
• Connect a pair of headphones to the PHONES
jack to verify that sound is output from the
headphones. If only one channel is output from the
headphones, the component may not be connected
to the receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
receiver and the component. If both channels are
output from the headphones, the front speaker
may not be connected to the receiver correctly.
Check the connection of the front speaker which is
not outputting any sound.
There is no sound from digital sources (from
COAXIAL or OPTICAL input jack).
• Check that the INPUT MODE is not set to
“ANALOG” (page 31). Check that the INPUT
MODE is not set to “COAX IN” for the sources
from OPTICAL input jack, or set to “OPT IN” for
the sources from COAXIAL input jack.
• Check that you have not selected “MULTI CH IN”.
The left and right sounds are unbalanced or
reversed.
• Check that the speakers and components are
connected correctly and securely.
• Adjust balance parameters in the LEVEL menu.
There is severe hum or noise.
• Check that the speakers and components are
connected securely.
• Check that the connecting cords are away from a
transformer or motor, and at least 3 meters away
from a TV set or fluorescent light.
• Move your TV away from the audio components.
• The plugs and jacks are dirty. Wipe them with a
cloth slightly moistened with alcohol.
There is no sound or only a very low-level
sound is heard from the center or/and
surround speaker.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
• Select the CINEMA STUDIO EX mode
(page 29).
• Adjust the speaker level (page 20).
• Make sure the center or/and surround speaker size
parameter is set to either “SMALL” or “LARGE”
(page 18).
Additional Information
There is no sound or only a very low-level
sound no matter which component is
selected.
• Check that the speakers and components are
connected securely and correctly.
• Check that both the receiver and all components
are turned on.
• Check that you have selected the correct
component on the receiver.
• Check that MASTER VOLUME –/+ is not set at
“VOL MIN”.
• Check that the SPEAKERS (OFF/A/B/A+B) is
not set to off (page 36).
• Check that the headphones are not connected.
• Press MUTING on the remote to cancel the
muting function.
There is no sound from analog 2 channel
sources.
• Check that the INPUT MODE is not set to “COAX
IN” or “OPT IN” (page 31).
• Check that you have not selected “MULTI CH IN”.
There is no sound from the sub woofer.
• Check that the sub woofer is connected correctly
and securely.
• Make sure the sub woofer selection parameter is
set to “YES” (page 18).
• There is no sound output from the sub woofer
depending on the sound field.
The surround effect cannot be obtained.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
• Sound fields do not function for the signals with a
sampling frequency of more than 48 kHz.
continued
43GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB09ADD_STR-DE497CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 44 Friday, July 16, 2004 2:34 PM
Dolby Digital or DTS multi channel sound is
not reproduced.
• Check that the playing DVD, etc. is recorded in
Dolby Digital or DTS format.
• When connecting the DVD player, etc. to the
digital input jacks of this receiver, check the audio
setting (settings for the audio output) of the
connected component.
Recording cannot be done.
• Check that the components are connected
correctly.
• Select the source component with input buttons.
• Make sure that INPUT MODE is set to
“ANALOG” (page 31) before recording from a
digital component connected to the analog MD/
TAPE terminals.
The FM reception is poor.
• Use a 75-ohm coaxial cable (not supplied) to
connect the receiver to an outdoor FM antenna as
shown below. If you connect the receiver to an
outdoor antenna, ground it against lightning. To
prevent a gas explosion, do not connect the ground
wire to a gas pipe.
Outdoor FM antenna
Receiver
ANTENNA
RDS does not work.*
• Make sure that you are tuned to an FM RDS
station.
• Select a stronger FM station.
The RDS information that you want does not
appear.*
• Contact the radio station and find out whether they
actually provide the service in question. If so, the
service may be temporarily out of order.
There is no picture or an unclear picture
appears on the TV screen or monitor.
• Select the appropriate input on the receiver.
• Set your TV to the appropriate input mode.
• Move your TV away from the audio components.
* Models of area code CEL, CEK only.
Remote control
The remote does not function.
• Point the remote at the remote sensor
on the
receiver.
• Remove any obstacles in the path between the
remote and the receiver.
• Replace all the batteries in the remote with new
ones, if they are weak.
• Make sure you select the correct input on the
remote.
AM
Ground wire
(not supplied)
Error message
If there is a malfunction, the display shows a
message.
To ground
Radio stations cannot be tuned in.
• Check that the antennas are connected securely.
Adjust the antennas and connect an external
antenna if necessary.
• The signal strength of the stations is too weak
(when tuning in with automatic tuning). Use direct
tuning.
• Make sure you set the tuning interval correctly
(when tuning in AM stations with direct tuning).
• No stations have been preset or the preset stations
have been cleared (when tuning by scanning
preset stations). Preset the stations (page 23).
• Press DISPLAY repeatedly so that the frequency
appears in the display.
PROTECT
Irregular current is output from the speakers. The
receiver will automatically turn off after a few
seconds. Check the speaker connection and turn on
the power again. If this problem persists, consult
your nearest Sony dealer.
44GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB09ADD_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 45 Friday, July 16, 2004 2:34 PM
If you are unable to remedy the
problem using the
troubleshooting guide
Clearing the receiver’s memory may remedy the
problem (page 17). However, note that all
memorized settings will be reset to their factory
settings and you will have to readjust all settings
on the receiver.
If the problem persist
Consult your nearest Sony dealer.
Reference sections for clearing
the receiver’s memory
To clear
See
All memorized settings
page 17
Customized sound fields
page 32
Specifications
Amplifier section
POWER OUTPUT
Models of area code CEL, CEK
Rated Power Output at Stereo Mode
(8 ohms 1 kHz, THD 0.7%)
80 W + 80 W1)
Reference Power Output1)
(8 ohms 1 kHz, THD 0.7%)
FRONT2): 80 W/ch
CENTER2): 80 W
SURR2): 80 W/ch
Additional Information
Models of area code AU
Rated Power Output at Stereo Mode
(8 ohms 20 Hz – 20 kHz, THD 0.09%)
50 W + 50 W1)
(8 ohms 1 kHz, THD 0.7%)
80 W + 80 W1)
Reference Power Output1)
(8 ohms 20 Hz – 20 kHz, THD 0.09%)
FRONT2): 50 W/ch
CENTER2): 50 W
SURR2): 50 W/ch
(8 ohms 1 kHz, THD 0.7%)
FRONT2): 80 W/ch
CENTER2): 80 W
SURR2): 80 W/ch
(8 ohms 1 kHz, THD 10%)
FRONT2): 100 W/ch
CENTER2): 100 W
SURR2): 100 W/ch
Models of area code KR
Rated Power Output at Stereo Mode
(8 ohms 1 kHz, THD 0.7%)
80 W + 80 W1)
70 W + 70 W3)
(8 ohms 1 kHz, THD 10%)
FRONT2): 100 W/ch
CENTER2): 100 W
SURR2): 100 W/ch
continued
45GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB09ADD_STR-DE497CEL.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 46 Friday, July 16, 2004 2:34 PM
Models of other area code
Rated Power Output at Stereo Mode
(8 ohms 1 kHz, THD 0.7%)
80 W + 80 W1)
1)
Reference Power Output
(8 ohms 1 kHz, THD 10%)
FRONT2): 100 W/ch
CENTER2): 100 W
SURR2): 100 W/ch
Inputs (Digital)
DVD (Coaxial)
Sensitivity: –
Impedance: 75 ohms
S/N: 100 dB
(A, 20 kHz LPF)
VIDEO 2, SA-CD/CD
(Optical)
Sensitivity: –
Impedance: –
S/N: 100 dB
(A, 20 kHz LPF)
1) Measured under the following conditions:
Area code
Power requirements
SP, CEL, CEK, KR
230 V AC, 50 Hz
E2/E3, AU
240 V AC, 50 Hz
TW
110 V AC, 60 Hz
Outputs (Analog)
MD/TAPE (OUT),
VIDEO 1 (AUDIO OUT)
Voltage: 500 mV
Impedance: 10 kiloohms
SUB WOOFER
Voltage: 2 V
Impedance: 1 kiloohms
2) Depending on the sound field settings and the
source, there may be no sound output.
3) Measured under the following conditions:
TONE
Area code
Power requirements
FM tuner section
KR
220 V AC, 50 Hz
Frequency response
MULTI CH IN,
SA-CD/CD, MD/TAPE,
DVD, VIDEO 1, 2
10 Hz – 70 kHz
+0.5/–2 dB (with sound
field and tone bypassed)
Inputs (Analog)
MULTI CH IN,
SA-CD/CD, MD/TAPE,
DVD, VIDEO 1, 2
Sensitivity: 500 mV
Impedance: 50 kiloohms
S/N4): 96 dB
(A, 500 mV5))
4) INPUT SHORT (with sound field and tone
bypassed).
5) Weighted network, input level.
Gain levels
±6 dB, 1 dB step
Tuning range
87.5 - 108.0 MHz
Antenna
FM wire antenna
Antenna terminals
75 ohms, unbalanced
Intermediate frequency
10.7 MHz
Sensitivity
Mono:
18.3 dBf, 2.2 µV/75 ohms
Stereo:
38.3 dBf, 22.5 µV/75 ohms
Useable sensitivity
11.2 dBf, 1 µV/75 ohms
S/N
Mono:
76 dB
Stereo:
70 dB
Harmonic distortion at 1 kHz
Mono:
0.3%
Stereo:
0.5%
Separation
45 dB at 1 kHz
Frequency response
30 Hz – 15 kHz,
+0.5/–2 dB
Selectivity
60 dB at 400 kHz
46GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB09ADD_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 47 Friday, July 16, 2004 2:34 PM
AM tuner section
Supplied accessories
Tuning range
Models of area code E2/E3
With 10-kHz tuning scale: 530 – 1,610 kHz6)
With 9-kHz tuning scale: 531 – 1,602 kHz6)
Models of area code CEL, CEK, SP, AU, TW, KR
With 9-kHz tuning scale: 531 – 1,602 kHz
Antenna
Loop antenna
Intermediate frequency
450 kHz
Usable sensitivity
50 dB/m (at 1,000 kHz or
999 kHz)
S/N
54 dB (at 50 mV/m)
Harmonic distortion
0.5% (50 mV/m, 400 Hz)
Selectivity
At 9 kHz:
35 dB
At 10 kHz:
40 dB
FM wire antenna (1)
AM loop antenna (1)
Remote commander RM-U306B (1)
R6 (size-AA) batteries (2)
For details on the area code of the component you
are using, see page 3.
Design and specifications are subject to change
without notice.
Additional Information
6) You can change the AM tuning scale to 9 kHz or 10
kHz. After tuning in any AM station, turn off the
receiver. While holding down PRESET TUNING +
or TUNING +, press ?/1. All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the procedure.
Video section
Inputs/Outputs
Video:
1 Vp-p, 75 ohms
General
Power requirements
Area code
Power requirements
CEL, CEK
230 V AC, 50/60 Hz
SP, KR
220 – 230 V AC,
50/60 Hz
E2/E3
120/220/240 V AC,
50/60 Hz
AU
240 V AC, 50 Hz
TW
110 V AC, 50/60 Hz
Power consumption
Area code
Power consumption
CEL, CEK, SP, AU,
E2/E3, KR
180 W
TW
440 W
Power consumption (during standby mode)
0.3 W
Dimensions (w/h/d) (Approx.)
430 × 145 × 310.5 mm
including projecting parts
and controls
Mass (Approx.)
7.5 kg
47GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB09ADD_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 48 Friday, July 16, 2004 2:34 PM
List of button locations and reference pages
How to use page 48 and 49
Use this page to find the location of buttons that are
mentioned in the text.
Illustration number
r
DISPLAY 3 (25, 26, 44)
R
Name of button/part
R
Reference page
Main unit
ALPHABETICAL ORDER
A-L
A.F.D. (button/indicator) qs (28,
29, 30, 43)
DIMMER 4 (26)
DISPLAY 3 (25, 26, 44)
Display 7 (25, 26)
DVD wk (21)
ENTER 9 (17, 18, 35)
FM MODE wd (22)
Input buttons ql (21, 31, 34, 35)
INPUT MODE qh (31)
IR (receptor) 5 (38, 44)
M-Z
MAIN MENU 8 (18, 31, 33, 35)
MASTER VOLUME –/+ qg (17,
20, 21, 43)
MD/TAPE wj (21)
MEMORY ws (23)
MOVIE (button/indicator) qd
(29, 43)
MULTI CH IN q; (21)
MULTI CHANNEL DECODING
(indicator) 6 (21)
MUSIC (button/indicator) qf (30,
43)
PHONES (jack) wf (21, 43)
PRESET TUNING –/+ w; (23,
47)
SA-CD/CD wh (21)
SPEAKERS (OFF/A/B/A+B) 2
(16, 36, 43)
TUNER FM/AM wg (21, 22, 23,
24, 35)
TUNING –/+ wa (22, 47)
VIDEO 1 e; (21)
VIDEO 2 wl (21)
NUMBERS AND SYMBOLS
2CH (button/indicator) qa (28,
30, 32)
+/– qj (18, 31, 33, 35)
</> qk (18, 31, 33, 35)
?/1 (power) 1 (17, 18, 23, 32,
47)
48GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB09ADD_STR-DE497CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 49 Friday, July 16, 2004 2:34 PM
2 3 4
1
wf
wd ws
wa
5
6
w;
8 9 q; qa qs qd qf
ql
wl
wk
qk qj qh
wj
wh
qg
Additional Information
e;
7
wg
49GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB01COV_STR-DE497CELIX.fm]
masterpage:Left
GB01COV_STR-DE497-CEL.book Page 50 Friday, July 16, 2004 2:34 PM
Index
A
R
Adjusting
CUSTOMIZE parameters 33
LEVEL parameters 31
SET UP parameters 18
speaker levels and balance 20
TONE parameters 33
Automatic tuning 22
RDS 24
Recording
on a video tape 37
on an audio tape or MD 37
C
Changing
display 26
Clearing receiver’s memory 17
CUSTOMIZE menu 33
D
Digital Cinema Sound 29
Direct tuning 22
Dual Mono 34
Dubbing. See Recording
E
S
Selecting
component 21
front speaker system 36
sound field 29–30
SET UP menu 18
Sleep Timer 36
Sound field
customizing 31
pre-programmed 29–30
resetting 32
selecting 29–30
Speakers
adjusting speaker levels and balance 20
connection 15
placement 15
Supplied accessories 46
Editing. See Recording
T
I
Indexing. See Naming
L
Labeling. See Naming
LEVEL menu 31
Test tone 20
TONE menu 33
Tuning
automatically 22
directly 22
to preset stations 24
N
Naming 35
P
Preset stations
how to 23
how to tune 24
50GB
model name1[STR-DE497]
[4-252-084-13(1)]
lename[D:\DataSEM_Llily\Revision_DE497\4252084131\4252084131\GB010BKC_STRDE497-CEL.fm]
masterpage:Right
GB01COV_STR-DE497-CEL.book Page 51 Friday, July 16, 2004 2:34 PM
Sony Corporation Printed in Malaysia
model name1[STR-DE497]
model name2[HT-4800]
[4-252-084-13(1)]
Download PDF

advertising