Canon MX410 All in One Printer User Manual

Using Your Multifunction with
Additional computers on Your Network
PIXMA MX410
Mac OS
1
Navigation Tips for Macintosh Users
To navigate this guide, please use the arrows on the MAC
keyboard or use the PAGE UP and Page DOWN keys.
DOWN
LEFT
RIGHT
Page UP
UP
Page DOWN
2
Using Your Multifunction with
Additional computers on Your Network
PIXMA MX410
Mac OS
Preparing to Connect My Multifunction to My Network
Network Requirements
Important Information You Need Before Adding Your Multifunction
Installing the Drivers & Software
Registering the Printer & Scanner
4
4
5
6
13
3
Preparing to Connect My Multifunction
To My Network
Network Requirements
Before connecting the machine to the network, make sure that configuration of the computer and access point or router is
complete, and that the computer is connected to the network.
Notes on Network Connection
•
The configuration, router functions, setup procedures and security settings of the network device vary depending on your
system environment. For details, refer to your device's instruction manual or contact its manufacturer.
•
The machine cannot be used over a wireless and wired connection at the same time.
Wireless Connection
Connect to your network environment over a wireless connection.
4
Preparing to Connect My Multifunction
To My Network
An "Ad-hoc connection," which establishes a direct
connection to the computer over a wireless connection
without using an access point, is not supported.
Be sure to prepare an access point.
Important Information You Need Before Adding Your Multifunction
The following information is required to connect to your access point or router.
• Access Point Name/Network Name:
Also referred to as SSID. A name to identify the specific access point.
• Network Key:
Also referred to as encryption key, WEP key or WPA/WPA2 passphrase, Pre-Shared key.
A password required to set to prevent unauthorized access to communication.
Check your access point or router for the following information, and then write it down.
NOTE: For details on how to check the following information, refer to the manual of your access point or router, or contact its manufacturer.
5
Installing the Drivers & Software
Installing the Drivers & Software
To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The
installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of applications
to be installed.)
Step One
Step Two
Turn on the computer, then insert the Setup
CDROM into the CD-ROM drive
Double-click the Setup icon of the CD-ROM folder to proceed to the
following screen.
If the CD-ROM folder does not open automatically, double-click the
CD-ROM icon on the desktop.
6
Installing the Drivers & Software
Step Three
Step Four
Enter your administrator name and password. Click OK.
Click Easy Install. Click Install.
The drivers, application software, and on-screen manuals are installed all together.
If you do not know your administrator name or password, click
Help
, then follow the on-screen instructions.
7
Installing the Drivers & Software
Step Five
Step Six
Click Install
Select Use the printer with wireless LAN connection, then click
Next.
*Applications may vary by model
Follow any on-screen instructions to proceed with the software
installation.
8
Installing the Drivers & Software
Step Seven
Step Eight
Read the License Agreement screen carefully and click Yes.
When the Create an Alias on Desktop screen appears, select
Agree if you want an alias of the On-Screen manual to be placed on
the desktop , otherwise select Do not Agree, then click Next
9
Step Nine
Step Ten
Select Agree or Do not Agree on the Add Easy-WebPrint EX to
the Dock screen, then click Next
Click Skip or Next on the Download Easy-webPrint screen
10
Step Eleven
Step Twelve
When the Printer Detection screen appears, click Next
Make sure the machine is turned on, then click OK.
11
Installing the Drivers & Software
Step Thirteen
When the Detected Printers List screen appears, select
your printer and click Next.
Step Fourteen
When the Setup Completion screen appears, click
.
Complete or OK
12
Registering the Printer & Scanner
Registering the Printer & Scanner
This section describes how to register the machine on a Macintosh computer.
Step One
When the Register Printer and Scanner screen appears,
click Register Printer.
Proceed to the section that relates to your operating
system for further installation instructions
Mac OS X v. 10.5.x / 10.6.x: Go to Step 2-A
Mac OS X v. 10.4.11: Go to Step 2-B
13
Registering the Printer & Scanner
Step Two
Step Two
2-A
1. Select Canon MXxxx series in the list of printers, then
click Add . *xxx refers to the model number. MX410 series
shown in example, below
2-B (OS X v. 10.4.11)
1. When the Printer List window appears, click Add.
2. Go to Step Three, page 19.
*The alphanumeric characters after Canon xxxx series is the machine's Bonjour
service name or MAC address
14
Registering the Printer & Scanner
Step Two
Step Two
2-B
2. Click More Printers in the Printer Browser window.
2-B
3. Select Canon IJ Network in the pop-up menu, select Canon
MXxxx series in the list of printers, then click Add . *xxx refers
to the model number. MX410 series shown in example, below
15
Registering the Printer & Scanner
Step Two
Step Three
2-B
4. Make sure that the Canon MXxxx series is added to the
list of printers.
When the Register Printer and Scanner screen appears, click
Register Scanner.
*xxx refers to the model number. MX410 series shown in
above example.
16
Registering the Printer & Scanner
Step Four
Step Five
Select Canon MX410 series on the Canon IJ Network Scanner
Selector EX screen, then click OK
Click Next on the Register Printer and Scanner screen.
17
Registering the Printer & Scanner
Step Six
Step Seven
Click Next on the Print Head Alignment Recommended
screen.
Click Next on the Register Printer and Scanner screen.
18
Registering the Printer & Scanner
Step Eight
If the User Registration screen appears, read the information
and click Next or Cancel.
If the Extended Survey Program screen appears: If you can
agree to Extended Survey Program, click Agree. If you click Do
not agree, the Extended Survey Program will not be installed.
(This has no effect on the machine's functionality.).
19
Registering the Printer & Scanner
Step Nine
Click Exit. Setup is complete
*It is necessary to restart the computer before scanning using the
Operation Panel on the machine for the first time.
20