Getting Started fi-60F Image Scanner P3PC-1102-01EN

Getting Started fi-60F Image Scanner P3PC-1102-01EN
P3PC-1102-01EN
fi-60F Image Scanner
Getting Started
CONTENTS
■ Regulatory Information ........................................................ ii
■ Note, Liability ....................................................................... iii
■ Safety Precautions ............................................................... iv
Chapter 1
PREPARING THE SCANNER.................................. 1
1.1 Checking the Contents of the Scanner Package............. 1
1.2 Names and Functions of Parts.......................................... 1
Chapter 2
INSTALLATION OF THE SCANNER...................... 2
2.1 Installing the Scanner Application ................................... 2
2.2 Installing the Scanner ........................................................ 5
2.3 Connecting the Scanner to Your PC................................. 6
2.4 Confirming the Installation ................................................ 7
2.5 Installing Adobe® Acrobat® Reader ................................ 8
Appendix 1 TROUBLESHOOTING........................................ AP-1
Appendix 2 DAILY CARE ...................................................... AP-2
fi-60F Image Scanner Getting Started
i
INTRODUCTION
Thank you for purchasing the fi-60F Scanner product.
This document describes how to handle fi-60F Scanner
and basic operation methods. Before you start using fi60F Scanner be sure to thoroughly read this manual to
ensure correct use.
The "Operator’s Guide" is stored on the Setup Disk.
The guide provides useful and detailed information on
operations when you would like to use advanced features, daily maintenance of the scanner, replacement of
consumables. Please also read the Operator’s Guide for
your reference.
■ Regulatory Information
FCC Declaration
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment
and receiver.
ATTENTION
The use of a shielded interface cable
is required to comply with the Class B
limits of Part 15 of FCC rules.
The length of the AC cable must be 2
meters (6.6 feet) or less.
Canadian DOC Regulations
This digital apparatus does not exceed the Class B
limit for radio noise emissions from digital
apparatus set out in the Radio interference
Regulations of the Canadian Department of
Communications.
This Class B digital apparatus complies with
Canadian ICES-003.
Le pésent appareil numérique n’ément pas de
bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la classe
B prescridtes dans le Réglesment sur le brouillage
radioélectrique dicté par le ministere des
Communications du Canada.
Cet appareil numérique de la classe B est
conformme à la norme NMB-003 du Canada.
Bescheimigung des Herstellers /
Importeurs
Hiermit wird bescheinigt, daß der/die/das
fi-60F
•In Übereinsstimmung mit den Bestimmungen
der EN45014(CE) funkentstört ist.
•Laut Maschinenlärminformationsverordnung 3.
•Connect the equipment into an outlet on a circuit
GS GV, 18.01.1991:Der höchste
Schalldruckpegel beträgt 70 dB (A) oder
weniger gemäß ISO/7779.
•Consult your dealer or an experienced radio/TV
International ENERGY STAR® Program
different from that to which the receiver is
located.
technician.
FCC warning: Changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
ii
As an ENERGY STAR®
Partner, PFU LIMITED has
determined that this product
meets the ENERGY STAR®
guidelines for energy efficiency.
The International ENERGY STAR® Office
Equipment Program is an international program
that promotes energy saving through the
penetration of energy efficient computers and
other office equipment. The program backs the
development and dissemination of products with
functions that effectively reduce energy
consumption. It is an open system in which
business proprietors can participate voluntarily.
The targeted products are office equipment such
as computers, monitors, printers, facsimiles,
copiers, scanners, and multifunction devices.
Their standards and logos (
among participating nations.
How Trademarks Are Indicated In
This Manual
References to operating systems (OS) are
indicated as follows:
Windows 98
Microsoft® Windows® 98
operating system.
Windows Me
Microsoft® Windows® Millennium Edition operating system.
Windows 2000
Microsoft® Windows® 2000 Professional operating system.
Windows XP
Microsoft® Windows® XP Professional operating system,
Microsoft® Windows® XP Home
Edition operating system.
) are uniform
Use in High-safety Applications
This product has been designed and manufactured
on the assumption that it will be used in office,
personal, domestic, regular industrial, and
general-purpose applications. It has not been
designed and manufactured for use in applications
(simply called "high-safety applications" from
here on) that directly involve danger to life and
health when a high degree of safety is required,
for example, in the control of nuclear reactions at
nuclear power facilities, automatic flight control
of aircraft, air traffic control, operation control in
mass-transport systems, medical equipment for
sustaining life, and missile firing control in
weapons systems, and when provisionally the
safety in question is not ensured. The user should
use this product with adopting measures for
ensuring safety in such high-safety applications.
PFU LIMITED assumes no liability whatsoever
for damages arising from use of this product by
the user in high-safety applications, and for any
claims or compensation for damages by the user
or a third party.
Trademarks
Where there is no distinction between the different
versions of the above operating system, the
general term "Windows " is used.
Manufacturer
PFU LIMITED
International Sales Dept., Imaging Business
Division, Products Group
Solid Square East Tower, 580 Horikawa-cho,
Saiwai-ku, Kawasaki-shi Kanagawa 212-8563,
Japan
Phone : (81-44) 540-4538
All Rights Reserved, Copyright© PFU LIMITED 2004.
■ Note, Liability
Microsoft and Windows are registered trademarks
of Microsoft Corporation in the United States and/
or other countries.
ISIS, QuickScan and their respective logos are
trademarks or registered trademarks of Pixel
Translations, a division of Captiva Software
Corporation in the United States.
Adobe, the Adobe logo, and Acrobat are either
registered trademarks of Adobe Systems
Incorporated in the United States and/or other
countries.
Other product names are the trademarks or
registered trademarks of the respective companies.
BEFORE USING THIS PRODUCT, PLEASE
READ THIS MANUAL CAREFULLY. IF THIS
PRODUCT IS NOT USED CORRECTLY,
UNEXPECTED INJURY CAN OCCUR TO
USERS OR BYSTANDERS.
Keep this manual in a safe place so that it can be
easily referred to during use of this product.
While all efforts have been made to ensure the
accuracy of all information in this manual, PFU
assumes no liability to any party for any damage
caused by errors or omissions or by statements of
any kind in this manual, its updates or
supplements, whether such errors are omissions or
statements resulting from negligence, accidents,
or any other cause. PFU further assumes no
liability arising from the application or use of any
fi-60F Image Scanner Getting Started
iii
product or system described herein; nor any
liability for incidental or consequential damages
arising from the use of this manual. PFU disclaims
all warranties regarding the information contained
herein, whether expressed, implied, or statutory.
Warning Indications Used In This
Manual
WARNING
This indication alerts operators
to an operation that, if not strictly
observed, may result in severe
injury or death.
CAUTION
This indication alerts operators
to an operation that, if not strictly
observed, may result in safety
hazards to personnel or damage
to equipment.
Screen Examples In This Manual
The screen examples in this manual are subject to
change without notice in the interest of product
improvement. If the actual displayed screen
differs from the screen examples in this manual,
operate by following the actual displayed screen
while referring to the User's Manual of the scanner
application you are using.
The screenshots in this manual were captured
from FUJITSU TWAIN32 scanner driver,
ScandAll 21 Image Capturing Utility Software,
FUJITSU ISIS scanner driver, QuickScan™
image capturing software and Adobe® Acrobat®.
About Maintenance
The user must not perform repairs on this scanner.
Contact the store where you purchased the scanner
or an authorized FUJITSU Image Scanner service
provider to have repairs done on this product.
Symbols Used In This Manual
ATTENTION
HINT
This symbol alerts operators to particularly important information. Be sure
to read this information.
This symbol alerts operators to helpful
advice regarding operation.
A TRIANGLE symbol indicates that special
care and attention is required.
The drawing inside the triangle shows the
specific caution.
A CIRCLE with a diagonal line inside
shows action which users may not perform.
The drawing inside or under the circle
shows the specific action that is not
allowed.
R
iv
Outline characters on a colored
background show instructions users should
follow.
It may also include the drawing that shows
the specific instruction.
■ Safety Precautions
WARNING
Do not damage the AC cable.
A damaged AC cable may cause fire or
electric shock. Do not place heavy objects
on AC cables, or pull, bend, twist, heat,
damage or modify AC cables.
Do not use damaged AC cables or power
plugs, or install any cables or power plugs
to loose wall sockets.
Use only specified AC cables and
connector cables.
Use only specified AC cables and
connector cables. Failure to use the
correct cables might cause electric shock
and/or equipment failure.
Please don't use the AC cable provided
with this scanner for other devices, since
this might cause equipment failure and
other troubles or an electric shock.
Use this scanner only at the
indicated power voltage. Do not
connect to multiple-power strips.
Do not touch the inside of the
scanner unless necessary.
Use this scanner only at the indicated
power voltage and current. Improper
power voltage and current might cause
fire or electric shock. Do not connect to
multiple-power strips.
Do not touch the AC cable with wet
hands.
Do not touch the power plug with wet
hands. Doing so might cause electric
shock.
Wipe any dust from the power plug.
Wipe off any dust from metal parts on the
power plug or metal fittings with a soft, dry
cloth. Accumulated dust might cause fire
or electric shock.
Do not install the device in locations
that has oil smoke, steam, humidity,
and dust.
Do not install the scanner in locations
subject to oil smoke, steam, humidity, and
dust. Doing so might cause a fire or
electric shock.
Turn the scanner OFF if it is
damaged.
If the scanner is damaged for any reason,
disconnect immediately the power plug in
order to turn out the scanner. Contact the
store where you purchased the scanner.
Do not put liquids inside the scanner.
Do not insert or drop metal objects in to the
scanner. Do not scan wet documents or
documents with paper clips or staples. Do
not splash or allow the scanner to get wet.
If foreign objects (water, small metal
objects, liquids, etc.) get inside the scanner,
disconnect immediately the power plug in
order to turn out the scanner. Then, contact
the store where you bought the scanner or
the Maintenance Service Center. Pay particular attention to this warning in households where there are small children.
Do not take apart or modify the scanner.
The inside of the scanner contains highvoltage components. Touching these
components might cause electric shock or
fire.
Do not use the scanner if there is a
strange odor.
If you detect excessive heat coming from
the device or detect other problems such as
smoke, strange smells or noises,
disconnect immediately the power plug in
order to turn out the scanner. Make sure
that any smoke coming from it has stopped,
before contacting the store where you
bought the scanner or an authorized
FUJITSU scanner service provider.
CAUTION
Do not install the scanner on
unstable surfaces.
Make sure that the scanner is installed on
a flat, level surface and that none of its
parts extend beyond the surface top, such
as a desk or table. Do not install the
scanner on unstable surfaces. Install the
scanner on a level surface that is free of
vibration to prevent it from falling.
Install the scanner on a strong surface that
will support the weight of the scanner and
other devices.
Do not place heavy objects or stand
on top of the scanner.
Do not place heavy objects on the scanner
or use the scanner's surface top to
perform other work. Improper installation
might cause injuries and equipment
failure.
Firmly insert the power plug.
Firmly insert the power plug as far it can
go into the power outlet.
fi-60F Image Scanner Getting Started
v
Do not use the scanner immediately
after moving it from a cold place into
a warm room.
Do not use the device immediately after
moving it from a cold place into a warm
room. Condensation may occur, which
might lead to scanning errors. Let the
device dry about one or two hours before
you use it.
Before moving the scanner,
disconnect the power plug from the
power outlet.
Do not move the scanner with the power
and interface cables connected as this can
damage the cables, which can later cause
fire, electric shock as well as injury.
Before moving the scanner, be sure to
disconnect the power plug from the power
outlet, and all other data cables.
Make sure that the floor is free of any
obstructions.
Protect the scanner from static
electricity.
Install the scanner away from strong
magnetic fields and other sources of
electronic noise. Also, protect the scanner
against any static electricity, which can
cause the scanner to malfunction.
Do not use aerosol sprays near the
scanner.
Do not use aerosol sprays to clean the
scanner. Aerosol sprays can blow dirt and
dust inside the scanner, resulting in scanner
failure or malfunction.
Disconnect the power plug from the
power outlet when the scanner is not
used for a long period of time
When the scanner is not going to be used
for a long period of time, be sure to
disconnect the power plug from the power
outlet for safety.
vi
Do not install the scanner in direct
sunlight.
Do not install the scanner under direct
sunlight or near heating apparatus. Doing so
might cause excessive heat to build up
inside the scanner, which can cause
scanner trouble or even fire. Install the
scanner in a well-ventilated location.
Before moving the scanner, make
sure the shipping lock is locked.
When moving the scanner, be sure to lock
the shipping lock in order to prevent
damages to the scanner.
Chapter 1
PREPARING THE SCANNER
■ Rear
1.1 Checking the Contents of
the Scanner Package
Shipping lock
When you open the scanner package, please handle the
main unit and its attachments carefully.
Make sure it contains all the parts listed in the package
contents list that is included in the package box.
If any parts are missing or defective, contact your sales
representative. Handle the scanner and accessories with
care.
DC inlet
Security slot
1.2 Names and Functions of Parts
USB interface connector
This section describes the scanner parts and their functions.
■ Front
■ Inside
Document cover
Document holding pad
Document bed
LED
fi-60F Image Scanner Getting Started
1
Chapter 2
INSTALLATION OF THE SCANNER
2.1 Installing the Scanner
Application
Both the scanner driver and image capturing application
software (called "application" hereafter) must be
installed on your PC.
Two types of drivers are available for this scanner, a
FUJITSU TWAIN 32 Scanner Driver and a FUJITSU
ISIS Scanner Driver, as well as two software applications, ScandAll 21 and QuickScan Pro™, are provided
with this product. The following sections describe how
to install each driver and application.
■ Installing the FUJITSU TWAIN32
Scanner Driver
Windows XP screenshots are used in
this section as examples. The windows
and operations may slightly vary
depending on your OS.
HINT
1. Turn on your PC and log on to Windows.
ATTENTION
ATTENTION
Please install the scanner driver
before connecting the scanner to your
PC.
If you connect the scanner before
installing the scanner driver, the scanner will not operate correctly.
If you have connected the scanner
beforehand, the "Found New Hardware Wizard" screen appears (this
screen might differ slightly according
to the used OS) . On this screen, click
the [Cancel] button to close the
Wizard screen and install the scanner
driver first.
When using Windows 2000 or Windows XP, log on as a user with
"Administrator" privileges (privileges
of the administrator of your PC).
2. Insert the Setup CD-ROM into the CD drive.
⇒ <SETUP DISK START UP SCREEN> appears.
ATTENTION
This screen may not appear when the
"Autoplay" setting of your PC is OFF.
In this case, run "Install.exe" in this
CD-ROM directly from the "Explorer"
or "My Computer".
3. Click [INSTALL PRODUCTS].
For FUJITSU TWAIN32 Scanner Driver
■ Preparation
Confirm the following items before installing the application.
• Remove the Setup CD-ROM from its package,
but do not insert the Setup CD-ROM into the
CD driver yet.
• Uninstall any older versions of FUJITSU
TWAIN 32 driver if already installed.
ATTENTION
2
Uninstall [Scanner Utility for Microsoft
Windows] from [Add/Remove Programs] of the control panel.
4. Click [TWAIN Driver] on the window below.
■ Installing ScandAll 21
"Scandall 21" is an image capturing software that complies with the TWAIN standard. The FUJITSU TWAIN
32 scanner driver enables you to capture images with a
FUJITSU image scanner fi-series product.
ATTENTION
When using Windows 2000 or Windows XP, log on as a user with
"Administrator" privileges (privileges
of the administrator of your PC).
1. Insert the Setup CD-ROM into the CD drive.
⇒ <SETUP DISK START UP SCREEN> appears.
5. Select a language used for installation on
[Choose Setup Language] window and click
[OK].
2. Click [INSTALL PRODUCTS].
6. Follow the instructions on the window to install
the application.
7. When the [InstallShield Wiizard Complete] window appears, click [Finish].
3. Click [ScandAll 21] on the window below.
Your computer will be restarted. Do not remove the
Setup CD-ROM from the CD drive until your PC has
completely restarted.
Installation of the scanner driver is completed.
ATTENTION
4. Select a language used for installation on
[Choose Setup Language] window and click
[OK].
To confirm whether the installation
was successful, perform a scanning
operation with an application that
complies with the TWAIN regulations
such as ScandAll 21.
fi-60F Image Scanner Getting Started
3
5. Install the application following the instructions
on the window.
2. Insert the "Setup CD-ROM" into the CD drive.
⇒ <SETUP DISK START UP SCREEN> appears.
6. When the [InstallShield Wizard Complete] window appears, click [Finish]
ATTENTION
This screen may not appear when the
"Autoplay" setting of your PC is OFF.
In this case, run "Install.exe" in this
CD-ROM directly from the "Explorer"
or "My Computer".
3. Click [INSTALL PRODUCTS].
ATTENTION
To finish the installation, it may be
necessary to restart your computer.
Follow the instructions on the window.
For FUJITSU ISIS Scanner Driver
4. Click [ISIS Driver] on the window below.
■ Preparation
Confirm the following items before installing the driver
application.
• Remove the Setup CD-ROM from its package,
but do not insert the Setup CD-ROM into the CD
driver yet.
■ Installing the FUJITSU ISIS Scanner
Driver
HINT
5. Select a language used for installation on
[Choose Setup Language] window and click
[OK].
Windows XP screenshots are used in
this section as examples. The windows
and operations may vary slightly
depending on your OS.
1. Turn your PC on and log on to Windows.
ATTENTION
4
When using Windows 2000 or Windows XP, log on as a user with
"Administrator" privileges (privileges of
the administrator of your PC).
6. Follow the instructions on the window to install
the application.
7. When the [InstallShield Wizard Complete] window appears, click [Finish].
Your computer will be restarted. Do not remove the
Setup CD-ROM from the CD drive until your PC has
completely restarted
Now the installation of the scanner driver is completed.
4. Continue to install the application following the
instructions on the window.
■ Installing QuickScan Pro™
"QuickScan Pro™" is an image capturing software that
complies with the ISIS standard. The FUJITSU ISIS
scanner driver enables you to capture images with a
FUJITSU image scanner fi-series product.
ATTENTION
When using Windows 2000 or Windows XP, log on as a user with
"Administrator" privileges (privileges of
the administrator of your PC).
5. Enter the required information, then click [Next
>] button.
1. Insert the Setup CD-ROM into a CD drive.
⇒ <SETUP DISK STARTUP SCREEN> appears.
2. Click [INSTALL PRODUCTS].
ATTENTION
3. Click [QuickScan PRO (Trial)] on the window
below.
"QuickScan Pro™" included in the
Setup CD-ROM is an evaluation version. For further use after the expiration of its evaluation period of up to 30
launches, it is necessary to purchase
a fully functional version of QuickScan
Pro™. (When you install the evaluation version, do not change the Serial
Number already displayed.)
6. Install the application following the instructions
on the window.
2.2 Installing the Scanner
1. Place the scanner at its installation site.
For details on the scanner's dimensions and
required installation space, refer to "fi60F Operator’s Guide" "4.2 Installation Specifications" in
the Setup CD-ROM.
fi-60F Image Scanner Getting Started
5
2. Unlock the Shipping lock.
The carrier unit inside the scanner is secured by
the shipping lock to prevent the scanner from
becoming damaged during transportation from the
factory.
To unlock the shipping lock and use the scanner,
slide the switch on the rear of the scanner to the
right.
(locked)
2.3 Connecting the Scanner to
Your PC
■ Connecting the USB Interface Cable
1. Connect the USB interface cable to the USB
interface connector.
(unlocked)
3. Connect the AC adapter.
ATTENTION
Use only the AC adapter and cable
provided by the manufacturer.
1) Connect the AC cable to the AC adapter.
2. Connect the other end of the USB interface
cable to the PC.
Your scanner will be automatically detected.
For Windows 98:
When a request for inserting the CD-ROM for
Windows 98 appears, insert it into the CD drive
and click the [OK] button.
For Windows 2000:
When [Digital Signature not Found] appears,
click [Yes].
ATTENTION
2) Connect the AC adapter connector to the scanner’s DC inlet.
• Be sure to use the USB cable which
comes as an accessory with this
scanner.
Correct operation with commercially
available cables is not guaranteed.
• When connecting to an USB hub,
use the first stage USB hub that is
closest to the computer. If you use
the second or later hub stages, the
scanner may not operate correctly.
The installation of the scanner is completed.
3) Plug the AC cable into the outlet.
6
2.4 Confirming the Installation
HINT
■ Confirming with ScandAll 21
For details on [TWAIN driver], refer to
the "FUJITSU TWAIN32 Scanner
Driver User’s Guide" provided on the
Setup CD-ROM.
1. Load a document on the Scanner.
For details on how to load documents, refer to the
"1.2 Loading Documents on Scanner for Scanning" in the fi-60F Operator’s Guide provided in
the CD-ROM.
7. Documents are scanned, and the scanned
images are displayed on the [ScandAll 21] window.
2. Start ScandAll 21
Select [Start] - [All Programs] - [Scanner Utility
for Microsoft Windows] - [ScandAll 21].
3. Specify the scanner (that you will use).
Select [Select Source...] from the [Scan] menu of
ScandAll 21.
If the scanning completes without any trouble, the
installation performed successfully.
For details on various types of scanning, refer to the "fi60F Operator’s Guide" on the Setup CD-ROM.
4. Select "FUJITSU fi-60" on the dialog box.
■ Confirming with QuickScan Pro™
1. Load a document on the Scanner.
5. Select [To View...] from the [Scan] menu.
6. Set scanning resolution, document size, etc. on
the [TWAIN driver] window (for setting details
of scanning) and click the [Scan] button.
For details on loading documents, refer to
"1.2 Loading Documents on the Scanner for
Scanning" in the fi-60F Operator's Guide on
the Setup CD-ROM.
2. Start QuickScan Pro™.
From the [Start] menu select [All Programs][QuickScan]-[QuickScan].
3. Select [Select Scanner...] from [Scan] menu in
QuickScan Pro™.
4. Select fi-60F from the list of [Scanner:], and
then click the [OK] button.
fi-60F Image Scanner Getting Started
7
5. Click [OK] button.
6. Select [Preview Settings...] from the [Scan]
menu. Set the scan resolution, paper size and
other scanning requirements, and then click
[OK].
7. Select [Preview Scan] from the [Scan] menu.
And then the document is scanned.
If the scanning completes without any trouble, the
installation performed successfully.
HINT
8
Refer to "QuickScan Overview" or
"QuickScan Help" for information about
QuickScan Pro™ functions and operations. On the [Start] menu, point to [All
Programs]-[QuickScan] and click the
file.
2.5 Installing Adobe® Acrobat®
Reader
To view Operator's Guide included in Setup CD-ROM,
you will need to install "Adobe® Acrobat® Reader" on
your PC. You can install this program from your
<SETUP DISK START UP SCREEN> by clicking the
"USER'S GUIDE" button and then clicking "Install
Adobe Acrobat Reader".
Adobe, the Acrobat logo and Acrobat are registered
trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
Appendix 1 TROUBLESHOOTING
■ Troubleshooting checklist
Symptom
Scanner does not turn
on.
Scanning does not start.
Images are distorted or
blurred.
There is a shadow on
the leading edge of the
scanned image.
Check this item
Remedy
Are the AC cable, AC adapter and
the USB cable properly connected
to the scanner?
Correctly connect the AC and USB cable
and the AC adapter.
Are you using the correct AC and
USB cable and AC adapter supplied with the scanner from the
manufacturer?
You must use the AC adapter and AC and
USB cable supplied with your scanner by
the manufacturer. Please get the correct
AC adapter and cable to connect to your
scanner.
Is the scanner driver installed correctly?
Install the Scanner driver correctly. Refer to
"2.1 Installing the Scanner Application".
Did you unlock the shipping lock?
Unlock the shipping lock.
Is the USB cable connected correctly?
Connect the USB cable correctly.
Is the connector of the USB cable
broken?
Use a new USB cable and connect it correctly.
Does the scanning start after turning on the PC again?
The scanner operation is normal.
Is the USB cable connected to a
USB hub?
Connect directly into PC USB Port
Are the document bed and the document holding pad clean?
Clean the dirty locations as instructed in the
Operator's Guide "2. Daily Care".
Is something causing the scanner
to vibrate during scanning?
Do not allow anything to cause the scanner
to vibrate during scanning.
Is the scanner installed on a flat,
level surface?
Install the scanner on flat, level surface.
Is the document curled or folded?
Place the document flat and hold it down
slightly with the document cover.
Have you adjusted the offset?
Adjust the [Sub-scan Setting] on [Scanners
and Cameras] in the control panel.
Disconnect the AC cable, the AC adapter
and the USB cable from the scanner, then
connect them again.
If this does not restore the power supply,
contact the store where you purchased the
scanner or an authorized FUJITSU scanner
service provider.
fi-60F Image Scanner Getting Started
AP-1
Symptom
When the document is
scanned in Black &
White mode, the image
generated becomes
black.
Automatic paper size
detection is failed.
AP-2
Check this item
Remedy
Are the Document holding pad and
the Document bed of the scanner
clean?
Clean the dirty locations as instructed in the
Operator's Guide "2. Daily Care".
Have you tried to adjust the settings of the scanner driver (Threshold or Brightness)?
Adjust the Threshold and/or Brightness.
Did you scan a document so thin
that the contents of the backside
can be seen through?
Place a piece of white paper behind the
document and scan again.
- When there are any contents such as
characters on the backside of the document, they may be seen through and
appear in the scanned.
- When using "Automatic Size and Skew
detection", place a piece of white paper
of the same size as the document
behind the document.
Are the Document holding pad and
the Document bed of the scanner
clean?
Clean the dirty locations as instructed in the
Operator's Guide "2. Daily Care".
Did you scan with the document
cover closed?
Close the document cover and scan it
again.
Is the document rectangular or
square in shape?
If the document is other than rectangular or
square, the scanner may fail to detect the
size correctly.
Specify the area to scan in the driver setting window manually and scan it again.
Did you scan a document with any
corner folded?
If the corner is folded, unfold it.
Did you scan a document with
dark-colored edge(s)?
If the document has dark-colored edge(s),
the scanner may fail to detect the size correctly.
Specify the area to scan in the driver setting window manually and scan it again.
Appendix 2 DAILY CARE
■ Cleaning Materials
Cleaning Materials
Parts Number
Remarks
Cleaner F1
(or isopropyl alcohol)
CA99501-0013
1 bottle
Moisten the cloth with this fluid and wipe
the scanner clean. (*)
Lint-free dry cloth
Any commercially available cloth
* For details about cleaning materials, contact the FUJITSU scanner dealer where you purchased the scanner.
■ Parts to Clean
Part to clean
Document holding pad
Document bed
Remarks
Clean the locations using a soft
cloth moistened with cleaner F1.
fi-60F Image Scanner Getting Started
AP-3
fi-60F Image Scanner Getting Started
P3PC-1102-01EN
Date of issuance: October, 2004
Issuance responsibility: PFU LIMITED
Copying of the contents of this manual in whole or in part and
copying of the scanner application is forbidden under the copyright
law.
z The contents of this manual are subject to change without notice.
z PFU LIMITED. is not liable whatsoever for any damages resulting
from use of this scanner and procedures described in this manual,
profit due to defects, and any claims by a third party.
z
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement