C O M B I T H E R M

C O M B I T H E R M
C O M B I T H E R M
E L E C T R I C
®
TECHNICAL SERVICE MANUAL
20•20ES MARINE
W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA
PHONE:
PRINTED IN U . S . A .
262.251.3800 • 800.558.8744
USA / CANADA
FAX:
WWW. ALTO - SHAAM . COM
262.251.1907
20.20ESM
TECH
• 04/09
How to Use this Technical Service Manual
This manual has been compiled as a complete resource for a technician working on Combitherm Electric models. It includes
necessary product information and drawings, along with helpful troubleshooting procedures.
Introduction gives a quick overview of the Combitherm Electric line.
Sections 1 through 5:
– CONTROL PANEL IDENTIFICATION includes information on using the controllers and operating instructions. It is
the same material supplied to the customer.
– PREVENTIVE MAINTENANCE includes procedures for cleaning, performing a generator flush and decalcifying. This
information is also supplied to the customer.
– SERVICE MODE AND ERROR CODES explains the special programming available to you as a technician to view
status, make adjustments and test functions. Information is also included on the use of displayed error codes to resolve
problems and on the functions that can be operated under fault conditions.
– TROUBLESHOOTING TREES are provided for the most common conditions you will be required to address.
– COMBITHERM PARTS has drawings and lists of available parts.
Section 6 contains information that is specific to that model:
– The model’s Technical Data Sheet
– Parts Information that is unique to the model, including its door, condensation tank, directional panel and steam
generator or pressure box
– Wiring Diagrams
– Ladder Diagrams
20.20ES
MARINE
COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL
TA B L E O F C O N T E N T S
How to Use this Technical Service Manual......................................
2
Introduction ..................................................................................
4
1 — Control Panel Identification..................................................
5
2 — Preventive Maintenance.......................................................
42
3 — Service Mode and Error Codes.............................................
52
4 — Troubleshooting Trees .........................................................
60
5 — Combitherm Parts...............................................................
71
6 — 20.20 ES ...........................................................................
77
20.20ES
MARINE
COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 3
INTRODUCTION
MODEL NUMBERS
This manual covers the following model:
Steam Generator Models
20.20 ES
MARINE
CONTROLLER
• Deluxe is a touch key controller with programmable Rapid-Touch™ keys.
FEATURES AND OPTIONS
• Recessed Door is available on all models.
• Core Temp Probe (single point) is standard on deluxe controllers.
MODES
The Combitherm combination oven/steamer is a multipurpose oven used for:
STEAM MODE
COMBINATION MODE
CONVECTION MODE
RETHERM MODE
CORE TEMPERATURE MODE
20.20ES
MARINE
COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 4
1
C O N T R O L PA N E L I D E N T I F I C AT I O N
Deluxe Control .............................................................................
6
Return to Main Table of Contents ..................................................
3
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 5
C O N T R O L PA N E L I D E N T I F I C AT I O N
PROGRAMMABLE DELUXE MODELS
POWER ON/OFF KEY
STEAM MODE KEY
RETHERM MODE KEY
CONVECTION MODE KEY
PROGRAM INSTALL/EDIT KEY
START / STOP KEY
COMBINATION MODE KEY
PROGRAMMED MENU KEY
DELUXE MODELS ONLY
CHEF FUNCTION KEY
DELUXE MODELS ONLY
FUNCTION & OPERATING
INDICATORS
COOKING TEMPERATURE KEY
TIME KEY
DOWN ARROW KEY
CONTROL PANEL DISPLAY
CORE TEMPERATURE KEY
UP ARROW KEY
RAPID-TOUCH KEYS
ADJUSTMENT KNOB
DELUXE MODELS ONLY
MOISTURE VENT KEY
ELECTRIC MODELS ONLY
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 6
D E L U X E C O N T R O L PA N E L B A S I C F U N C T I O N
POWER ON/OFF KEY
DOWN ARROW KEY
Activates power to the oven and automatically fills
the steam generator equipped models with water
that will heat to a stand-by mode temperature of
150°F (65°C). The steam generator flush is also
activated by pressing this key.
ADJUSTMENT KNOB
The oven will operate in the steam mode at a
temperature range of 86°F to 248°F
(30°C to 120°C).
• Automatic steaming at 212°F (100°C)
FACTORY - SET DEFAULT .
function as the up and down arrow keys to
increase or decrease the displayed cook
temperature , time , or core temperature .
MOISTURE VENT KEY
ELECTRIC MODELS ONLY
Immediately vents steam and condensate from the
oven compartment while cooking in the Convection
mode or in the Combination mode .
RETHERM MODE KEY
START/STOP KEY
Food rethermalization or reheating mode will
Initiates all cooking mode functions and
programmed procedures stored in memory.
Stops an activated cooking mode or
programmed procedure currently in progress,
operate with automatic steam injection at a
temperature range of 248°F and 320°F
(120°C and 160°C).
CONVECTION MODE KEY
Selection key for convection cooking without
COMBINATION MODE KEY
Selection key for cooking with a combination
of steam and convection heat that can be set
within a temperature range of 212°F to 482°F
(100°C and 250°C).
scrolling key for programming functions.
Displays oven functions. Serves the same
and exits the Chef function key .
, time , or core temperature and as a
STEAM MODE KEY
• Quick steaming between 213°F and 248°F
(101°C and 120°C).
• Low Temperature Steaming between
86°F and 211°F (30°C and 99°C).
Used to decrease displayed cook temperature
steam at a temperature range of 86°F to 482°F
(30°C and 250°C).
PROGRAM INSTALL AND EDIT KEY
Used to create, change, duplicate, and delete
programmed menus.
PROGRAMMED MENU KEY
Used to access and exit a menu list of all
stored cooking programs that can be reviewed
•••••••CONTROL
in display .
DELUXE MODELS ONLY
DELUXE MODELS ONLY .
PANEL DISPLAY
CORE TEMPERATURE KEY
Used to set the required internal product
CHEF FUNCTION KEY
temperature, to recall the internal product
Used to select programmed menu functions,
various auxiliary functions, and several chef
help instructions.
temperature set by the operator, or to display
the current internal temperature of the product
in conjunction with the down arrow key , the
Used to set the required cooking temperature,
to recall the set cooking temperature, or to
check the actual oven temperature in
conjunction with the down arrow key , the
up arrow key or the adjustment knob .
up arrow key , or the adjustment knob .
COOKING TEMPERATURE KEY
TIME KEY
UP ARROW KEY
Used to increase displayed cook temperature
, time , or core temperature and as a
scrolling key for programming functions.
•••••••RAPID-TOUCH
KEYS
DELUXE MODELS ONLY.
Used to set the required cooking time or recall
the set cooking time in conjunction with the
One-touch cooking for immediate access to
down arrow key , the up arrow key , or
the adjustment knob .
cooking modes, cleaning, and other oven functions.
frequently used operator set programs including
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 7
CONTINUED
D E L U X E C O N T R O L PA N E L B A S I C F U N C T I O N S
FUNCTION & OPERATING INDICATORS
A.
Gold-n-Brown™ FEATURE
This indicator will illuminate when the browning function is set by the operator in a
timed or programmed cooking cycle in either convection mode or combination mode.
B.
COMBI SMOKER (ON
EQUIPPED MODELS)
This indicator will illuminate when the smoking function is set by the operator in a
timer, probe or programmed cooking cycle in either convection mode or combination
mode.
C.
REDUCED FAN SPEED
This indicator will illuminate whenever the operator sets a reduced fan speed to
protect products affected by high-velocity air movement.
D.
CONFIRMATION OF OVEN OPERATION
This indicator illuminates whenever the oven is operating in any mode.
E.
KEY LOCK
This indicator will illuminate when operator has locked any mode key or function to
prevent unauthorized or accidental changes.
F.
MOISTURE VENT
This indicator will illuminate whenever the Moisture Vent Key is pressed by the operator to eliminate excessive moisture.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 8
SET-UP PROCEDURES
SET UP MENU
Following installation, the control should be set with the date and time. In addition to the date and time,
the set-up function provides the operator with the ability to adjust a number of other Combither m
operating conditions to confor m with the needs of the individual installation.
PRESS THE ON/OFF POWER KEY
TO THE ON POSITION.
SET UP ADJUSTMENT CHOICES
PRESS THE CHEF FUNCTION KEY.
SIGNAL TONE
Rotate the adjustment knob
until the set up symbol is
VOLUME
highlighted within the display.
TIME
PRESS THE CHEF FUNCTION KEY.
Press the up and down arrow keys
or rotate the adjustment knob to select
DATE
“ YES ” for the set up function.
PROGRAM INDEX
Set up
DEFAULT/MEMO SETTINGS
TEMPERATURE DISPLAY
PRESS THE CHEF FUNCTION KEY TO
CONFIRM THE SET UP FUNCTION.
Press the up and down arrow keys
NETWORK ADDRESS
or rotate the adjustment knob to
highlight one of the following
LANGUAGE
adjustment functions:
SIGNAL TONE
Rotate the adjustment knob until the signal tone symbol
is highlighted within the display.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SIGNAL TONE SELECTION.
Press the up and down arrow keys or rotate the adjustment knob to select each tone offered.
Stop rotation at each individual setting to hear an audio playback. Select the tone desired.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SELECTED SIGNAL TONE SETTING.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 9
SET-UP PROCEDURES
A L W AY S B E G I N S E T U P A D J U S T M E N T S F R O M T H E S E T U P M E N U
.
VOLUME
Rotate the adjustment knob until the volume symbol
is highlighted within the display.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE VOLUME SELECTION.
Press the up and down arrow keys or rotate the adjustment knob to select each volume level
offered. Stop rotation at each individual setting to hear an audio playback. Select the volume
desired with consideration of the noise level within the kitchen during peak production periods.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE VOLUME SETTING.
TIME
Rotate the adjustment knob until the time symbol
is highlighted within the display.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE TIME SELECTION.
Press the up and down arrow keys to alternate between hours and minutes and rotate the
adjustment knob in each to adjust the numbers to the correct time.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SET TIME.
D AT E
Rotate the adjustment knob until the date symbol
is highlighted within the display.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE DATE SELECTION.
Rotate the adjustment knob to select the preferred date format.
Press the up and down arrow keys to alternate between day, month and year, and rotate the
adjustment knob in each to adjust the numbers to the correct settings.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SET DATE.
PROGRAM INDEX
Rotate the adjustment knob until the program index symbol
is highlighted within the display.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE PROGRAM INDEX SELECTION.
Press the up and down arrow keys or rotate the adjustment knob to select the preferred index format:
“YES” for a listing of programs entered alphabetically with the program install/edit key.
“NO” for a listing of programs entered numerically with the program install/edit key.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE PROGRAM INDEX SETTING.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 10
SET-UP PROCEDURES
A L W AY S B E G I N S E T U P A D J U S T M E N T S F R O M T H E S E T U P M E N U
.
D E FA U LT / M E M O S E T T I N G
The default/memo setting allows the operator to choose
between a display showing the factory set defaults for
time and temperature or the last operator set values for
time and temperature in each cooking mode. This
adjustment function also allows the operator to change
the defaults from those set at the factory to settings that
better meet the needs of the individual operation.
Cooking product with operator set defaults for time and
temperature can help reduce operator error. Cooking
with the oven in the memo setting is particularly useful
when several batches are cooked in succession. The
memo setting eliminates the necessity to set time and
temperature for each batch.
Rotate the adjustment knob until the default/memo symbol
is highlighted within the display.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE DEFAULT/MEMO SELECTION.
Rotate the adjustment knob to “NO” for memo. This setting will display the last operator set values for
time and temperature in each cooking mode.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE MEMO SETTING.
TO CHANGE THE DEFAULT SETTINGS
Rotate the adjustment knob to select “YES”.
A numbered list of default descriptions will appear in the display. Rotate the adjustment knob
until the setting to be changed is highlighted. Press the up arrow key to highlight the time or
temperature to be changed. Rotate the adjustment knob to change the default to the setting
desired. Press the down arrow key to save the new default setting.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE NEW DEFAULT SETTINGS.
COMBITHERM FACTORY SET DEFAULT SETTINGS
COOKING
MODE
OVEN
TEMPERATURE
CORE
TEMPERATURE
STEAM
212°F
158°F
MODE
(100°C)
(70°C)
COMBINATION
302°F
158°F
STEAM MODE
(150°C)
(70°C)
CONVECTION
MODE
RETHERM
MODE
338°F
158°F
(170°C)
(70°C)
275°F
158°F
(135°C)
(70°C)
DELTA-T
122°F
172°F
MODE
(50°C)
(77°C)
374°F
FREE
PREHEAT
MODE
COOKING
TIME
25 MINUTES
70 MINUTES
30 MINUTES
5 MINUTES
FREE
—
(140°C)
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 11
SET-UP PROCEDURES
A L W AY S B E G I N S E T U P A D J U S T M E N T S F R O M T H E S E T U P M E N U
.
T E M P E R AT U R E D I S P L AY
Rotate the adjustment knob until the temperature display symbol
is highlighted within the display.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE TEMPERATURE DISPLAY SELECTION.
Press the up and down arrow keys or rotate the
adjustment knob to select either Fahrenheit or Celsius.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE TEMPERATURE DISPLAY SETTING.
NETWORK ADDRESS
Press the up and down arrow keys or rotate the adjustment knob until the network address
symbol
is highlighted within the display.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE NETWORK ADDRESS SELECTION.
The current network address will appear in the display.
Rotate the adjustment knob to select 1 through 99 and assign
a different network number for each PC to be connected.
PRESS THE CHEF FUNCTION KEY TO CONFIRM EACH NETWORK ADDRESS.
LANGUAGE
Press the up and down arrow keys or rotate the adjustment knob
until the language symbol
is highlighted within the display.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE LANGUAGE PROGRAM SELECTION.
Rotate the adjustment knob to select the required language.
CHINESE
DUTCH
ENGLISH*
FRENCH
GERMAN
*U.S.
ITALIAN
JAPANESE
KOREAN
POLISH
PORTUGUESE
RUSSIAN
SPANISH
SWEDISH
FACTORY SETTING
NOTE : SOME OF THE LANGUAGE SELECTIONS SHOWN ABOVE MAY NOT BE AVAILABLE ON ALL MODELS .
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE LANGUAGE SETTING.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 12
I M P O R TA N T S A F E T Y P R E C A U T I O N S
NOTE: Automatic steam venting is a standard
safety feature built into all Combitherm
oven models. This feature vents all
steam from the oven compartment
IMMEDIATELY BEFORE COOKING
TIME EXPIRES.
This function is provided in all
programmed and timed production
when operating in any Steam,
Combination, Convection, and Retherm
cooking mode. Automatic steam
venting does not function if the oven
door is opened before time expires or
when the oven has been set to
continuous operation.
AT NO TIME SHOULD THE INTERIOR OR
EXTERIOR BE STEAM CLEANED, HOSED
DOWN, OR FLOODED WITH WATER OR
LIQUID SOLUTION OF ANY KIND. DO NOT
USE WATER JET TO CLEAN.
SEVERE DAMAGE OR
ELECTRICAL HAZARD COULD RESU LT.
WARRANTY BECOMES VOID IF APPLIANCE IS FLOODED.
DO NOT HANDLE PANS CONTAINING LIQUID
OR SEMILIQUID PRODUCTS POSITIONED
ABOVE THE EYE LEVEL OF THE OPERATOR.
SUCH PRODUCTS CAN SCALD AND CAUSE
SERIOUS INJURY.
HOT STEAM CAUSES BURNS
ROTATE THE DOOR HANDLE TO THE
FIRST OPEN ROTATION POSITION ONLY..
W AIT UN TIL TH E STE AM IS V EN TED
B E F O R E F U L LY O P E N IN G T HE D O O R.
DO
N O T USE THE ATTACHED HANDHELD HOSE TO SPRAY ANYTHING OTHER
THAN THE INTERIOR OF THE COMBITHERM
OVEN COMPARTMENT.
DO
N O T U S E T H E S P R AY H O S E
ON THE SURFACE OF A HOT COOKING
COMPARTMENT. ALLOW THE OVEN TO
COOL TO A MINIMUM OF 150°F (66°C).
METAL PARTS OF THIS EQUIPMENT
BECOME EXTREMELY HOT WHEN IN
OPERATION.
TO AVOID BURNS,
ALWAYS USE HAND PROTECTION
WHEN OPERATING THIS APPLIANCE.
N O T E: U S E A U T H O R I Z E D C O M B I T H E R M O V E N C L E A N E R O N L Y .
UNAUT HO RIZED CLEA NING AG E NT S MA Y D ISCOLO R OR HARM INT ERIO R S URF ACE S O F
THE O VEN. READ AND UNDER STA ND LA BEL AND M A T ER IA L S A F E T Y DA T A S H EE T
BEFOR E USING THE OVEN CLEANER .
FOR OPERATOR SAFETY
NOTE AND OBSERVE ALL SAFETY PRECAUTIONS LOCATED THROUGHOUT THIS GUIDE.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 13
STEAM MODE
STEAM ● LOW TEMPERATURE STEAM ● QUICK STEAM
The Steam mode provides the operator with the ability to steam, poach, or blanch.
This mode will automatically steam at the boiling point of water; quick-steam above the
boiling point for faster cooking results; or low temperature steam, below the boiling point,
for more delicate products such as pâté, mousse, seafood, or custard.
PRESS THE ON/OFF POWER KEY TO THE ON POSITION.
PRESS THE STEAM MODE KEY.
Automatic Steam temperature of 212°F (100°C) will appear in the display.
The last set time or oven control default setting for time will appear in the display.
PRESS THE START KEY TO STEAM AT THE SETTINGS SHOWN.
TO CHANGE THE SETTINGS SHOWN:
PRESS THE TEMPERATURE KEY.
The cooking temperature will appear highlighted within the oven display.
Press the up and down arrow keys or rotate the adjustment knob to select
the desired cooking temperature.
• Automatic Steaming 212°F (100°C)
• Quick-steaming 213°F to 248°F (101°C to 120°C)
• Low Temperature Steaming 86°F to 211°F (30°C to 99°C)
TO COOK BY TIME:
PRESS THE TIME KEY.
The cooking time will appear highlighted within the oven display.
Press the up and down arrow keys or rotate the adjustment knob to
select the time desired…
or
Set control for continuous operation by rotating the adjustment knob to the right until
appears in the display.
TO COOK BY INTERNAL PRODUCT TEMPERATURE:
PRESS THE CORE TEMP KEY.
The previously set core temperature or oven control default setting will appear
highlighted within the oven display.
Press the up and down arrow keys or rotate the adjustment knob to
select the inter nal temperature desired and insert the product probe.
PRESS THE START KEY TO BEGIN COOKING IN THE STEAM MODE.
• The set cooking temperature will appear in the display. To adjust the set temperature, press the
key
once and make corrections as required. To display the actual oven temperature, press the
key twice.
• The remaining cooking time will appear in the display. To display the set time or to change the set
values for time during operation, press the time key
once and make corrections as required.
• The actual internal product temperature will appear in the display. To display the set internal product
temperature or to change the set values for core temperature during operation, press the
key once
and make corrections as required.
When the cooking time has expired or the operator set internal temperature has been reached, a buzzer
will sound indicating the end of the operating mode.
• To stop the buzzer, press the start/stop key
or open the oven door.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 14
STEAM MODE
C H E F O P E R AT I N G T I P S
This mode will steam a full or partial load of a single product, or multiple products
without transfer of flavors. When steaming multiple products, however, individual
product cooking times must be taken into consideration. The non-pressurized
atmosphere of the Combitherm also provides the ability to open the door during the
steam mode in order to monitor products more closely throughout the steaming process.
STEAM
QUICK STEAMING
LOW TEMP STEAM
Perforated, 2-1/2" deep pans
Quick steaming is suitable
The low temperature steam mode
(65mm) are particularly suitable
for hearty, root-type vegetables
will function whenever the oven
for use in this program mode.
such as potatoes, legumes,
compartment temperature is
These pans will provide a shorter
and cabbage.
below 212°F (100°C).
product over-cooking at the
Quick steaming provides a
Proof yeast dough at a
bottom of the pan.
cooking time which is
temperature setting of 90°F to
approximately 10-percent shorter
110°F (32°C to 43°C).
cooking time and will prevent
Separate ice-encased vegetables
than the regular steam mode
before steaming to assure more
temperature of 212°F (100°C).
It will take longer to steam
products using the low
even cooking.
Set the steam cooking
temperature steam mode.
A variety of products can be
temperature between 221°F
steamed at the same time but
(105°C) and 230°F (110°C) for
Steaming sausages in low
attention must be paid to the
small loads and between 230°F
temperature steam prevents
different cooking times required
(110°C) and 248°F (120°C) for
cracked or peeling skins.
for each food product.
full loads.
Use low temperature steam for
Butter and season vegetables
delicate foods such as shrimp,
after steaming.
fish, seafood, and crème caramel.
Steam long-grain rice using
For best results, low temperature
approximately 1-part rice to
steam all delicate food items at a
approximately 1-1/2-parts water
temperature of 210°F (99°C)
or seasoned liquid.
or below.
Steam durum wheat noodles in
unperforated pans using 1-part
noodles to 5-parts cold water.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 15
C O M B I N AT I O N M O D E
The Combination mode will prove to be the most versatile and widely used mode
the Combitherm oven has to offer. It will produce the best possible results on the
widest variety of products — all within the shortest period of time. The unique control
function of this mode enables the operator to roast or bake with a combination of
steam and convection heat. In addition to shorter cooking times, this combination of
steam and heat offers less product shrinkage and more moisture retention than obtained
in a standard convection oven.
PRESS THE ON/OFF POWER KEY TO THE ON POSITION.
PRESS THE COMBINATION MODE KEY.
The last set values or oven control default setting for temperature will appear in the display.
The last set time or oven control default setting for time will appear in the display.
PRESS THE START KEY TO COOK AT THE SETTINGS SHOWN.
TO CHANGE THE SETTINGS SHOWN:
PRESS THE TEMPERATURE KEY.
The cooking temperature will appear highlighted within the oven display.
Press the up and down arrow keys or rotate the adjustment knob to
select the desired cooking temperature.
• 212°F to 482°F (100°C to 250°C)
TO COOK BY TIME:
PRESS THE TIME KEY.
The cooking time will appear highlighted within the oven display.
P ress the up and down arrow keys or rotate the adjustment knob to select
the time desired…
or
Set control for continuous operation by rotating the adjustment knob to the right until
appears in the display.
TO COOK BY INTERNAL PRODUCT TEMPERATURE:
PRESS THE CORE TEMP KEY.
The core temperature will appear highlighted within the oven display.
Press the up and down arrow keys or rotate the adjustment knob to
select the inter nal temperature desired and insert the product probe.
PRESS THE START KEY TO BEGIN COOKING IN THE COMBINATION MODE.
• The set cooking temperature will appear in the display. To adjust the set temperature, press the
once and make corrections as required. To display the actual oven temperature, press the
key
key twice.
• The remaining cooking time will appear in the display. To display the set time or to change the set
values for time during operation, press the time key
once and make corrections as required.
• The actual internal product temperature will appear in the display. To display the set internal
product temperature or to change the set values for core temperature during operation, press the
key once and make corrections as required.
When the cooking time has expired or the operator set internal temperature has been reached, a
buzzer will sound indicating the end of the operating mode.
• To stop the buzzer, press the start/stop key
or open the oven door.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 16
COMBINATION MODE
CHEF OPERATING TIPS
Th e C o m b i n a t i o n m o d e i n j e c t s t h e o p t i m u m a m o u n t o f s t e a m
automatically. There is no need to select moisture levels. Foods do not
dry out. Flavors are retained with no transfer of flavors when mixing
product loads.
Due to the automatic steam adjustment, the
door can be opened at any time during a
cooking operation. Be certain to observe the
safety war ning when opening the oven door.
The Combination mode is particularly efficient
when used for baking, broiling, grilling, stewing,
braising, and roasting.
When using the Combination mode, cooking
temperatures can be reduced 10- to 20-percent
below the temperatures used for conventional
cooking methods.
Cooking time will be reduced approximately
40-percent when cooking at the same temperature
used for convection oven cooking and up to 50- to
60-percent less time when cooking at the same
temperature used for a conventional oven.
Food browning in the Combither m begins
at a cooking temperature of approximately
248°F (120°C).
A higher cooking temperature results in heavier
browning but also results in greater product
weight loss. To achieve additional browning use
the Moisture Vent Key or set Gold-n-Brown into
the product procedure. Gold-n-Brown is
particularly useful for adding color to high moisture
products such as chicken and other poultry items
or for additional browning of full loads and other
moist products.
The Combination mode provides even browning
without the necessity to tur n the pans.
For more even cooking, do not cook in pans
deeper than 4-inches (100mm).
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 17
CONVECTION MODE
The Convection mode operates with hot circulated air within a temperature range
of 86° to 482°F (30° to 250°C). For many applications, better results may be
achieved with the Combination mode; therefore, the operator may want to consider
using the Convection mode on a more limited basis.
PRESS THE ON/OFF POWER KEY TO THE ON POSITION.
PRESS THE CONVECTION MODE KEY.
The last set values or oven control default setting for temperature will appear in the display.
The last set time or oven control default setting for time will appear in the display.
PRESS THE START KEY TO COOK AT THE SETTINGS SHOWN.
TO CHANGE THE SETTINGS SHOWN:
PRESS THE TEMPERATURE KEY.
The cooking temperature will appear highlighted within the oven display.
Press the up and down arrow keys or rotate the adjustment knob
to select the desired cooking temperature.
• 86° to 482°F (30° to 250°C)
TO COOK BY TIME:
PRESS THE TIME KEY.
The cooking time will appear highlighted within the oven display.
Press the up and down arrow keys or rotate the adjustment knob to select the
time desired…
or
Set control for continuous operation by rotating the adjustment knob to the right until
appears in the display.
TO COOK BY INTERNAL PRODUCT TEMPERATURE:
PRESS THE CORE TEMP KEY.
The core temperature will appear highlighted within the oven display.
Press the up and down arrow keys or rotate the adjustment knob to
select the inter nal temperature desired and insert the product probe.
PRESS THE START KEY TO BEGIN THE COOKING MODE.
• The set cooking temperature will appear in the display. To adjust the set temperature, press the
once and make corrections as required. To display the actual oven temperature, press the
key
key twice.
• The remaining cooking time will appear in the display. To display the set time or to change the set
values for time during operation, press the time key
once and make corrections as required.
• The actual internal product temperature will appear in the display. To display the set internal product
temperature or to change the set values for core temperature during operation, press the
key once
and make corrections as required.
When the cooking time has expired or the operator set internal temperature has been reached, a buzzer
will sound indicating the end of the operating mode.
• To stop the buzzer, press the start/stop key
or open the oven door.
To check the length of time the product has been operating in the core temperature mode, press and hold the
time key
along with the core temperature key
. The time period will appear at the top of the display.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 18
CONVECTION MODE
CHEF OPERATING TIPS
T h e C o n v e c t i o n M o d e c a n b e u s e d t o ro a s t o r b ak e p ro d u c t s n ee d i n g v e r y
s h o r t c o o k i n g t i m e s o r f o r h i g h m o i s t u re p ro d u c t s s u c h a s mu f f i n s , c a k e s ,
a n d c o o k i e s , o r f o r b ro w n i n g t h e s u r f a ce o f t h e p ro d u c t .
The Convection mode works best with foods
containing little moisture or for very moist food
which require a dryer finished product.
For baking, preheat the Combither m at a
temperature of 36°F to 54°F (20°C to 30°C) above
the baking temperature required. Once preheated,
reset the temperature as required.
A higher cooking temperature results in heavier
browning but also results in greater product weight
loss. To achieve additional browning use the
Moisture Vent Key or set the Browning Feature
into the product procedure.
To prevent the sur face of food from excessive
drying, the fan will not engage if the inter nal
oven temperature is above 212°F (100°C)
and the set oven temperature is below
212°F (100°C).
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 19
RETHERM MODE
The Retherm mode can be used to rethermalize (regenerate) portioned food on
plates, trays, or platters within a short period of time. Steam is automatically injected
into the oven compartment as required. Items are brought up to proper serving
temperatures without dry edges or condensate forming on the plates.
PRESS THE ON/OFF POWER KEY TO THE ON POSITION.
PRESS THE RETHERM MODE KEY.
The last set values or the default settings will appear in the display.
PRESS THE START KEY TO COOK AT THE SETTINGS SHOWN.
TO CHANGE THE SETTINGS SHOWN:
PRESS THE TEMPERATURE KEY.
The cooking temperature will appear highlighted within the oven display.
Press the up and down arrow keys or rotate the adjustment knob
to select the desired cooking temperature.
• 248° to 320°F (120° to 180°C)
TO COOK BY TIME:
PRESS THE TIME KEY.
The cooking time will appear highlighted within the oven display.
P ress the up and down arrow keys or rotate the adjustment knob to select the
time desired…
or
Set control for continuous operation by rotating the adjustment knob to the
right until
appears in the display.
TO COOK BY INTERNAL PRODUCT TEMPERATURE:
PRESS THE CORE TEMP KEY.
The core temperature will appear highlighted within the oven display.
Press the up and down arrow keys or rotate the adjustment knob to
select the inter nal temperature desired and insert the product probe.
PRESS THE START KEY TO BEGIN THE RETHERM MODE.
• The set cooking temperature will appear in the display. To adjust the set temperature, press the
key
once and make corrections as required. To display the actual oven temperature, press the
key twice.
• The remaining cooking time will appear in the display. To display the set time or to change the set
values for time during operation, press the time key
once and make corrections as required.
• The actual internal product temperature will appear in the display. To display the set internal product
temperature or to change the set values for core temperature during operation, press the
key once
and make corrections as required.
When the cooking time has expired or the operator set internal temperature has been reached, a buzzer
will sound indicating the end of the operating mode.
• To stop the buzzer, press the start/stop key
or open the oven door.
To check the length of time the product has been operating in the core temperature mode, press and hold the
time key
along with the core temperature key
. The time period will appear at the top of the display.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 20
RETHERM MODE CHEF OPERATING TIPS
Since plated meals consist of dissimilar products, there are several important factors
to consider in order to produce the finest results. Product density (compactness),
thickness, quantity of product on each plate, and quantity of plates all relate to the
length of time necessary to reheat. Again, experience is the best method to
determine reheating time. Once the time has been determined and recorded for a
specific meal, the results will be consistent for future reheating times.
HELPFUL HINTS FOR REHEATING ON THE PLATE
• ALL FOOD COMPONENTS ON THE PLATE SHOULD BE OF SIMILAR DENSITIES.
• ALL FOOD COMPONENTS ON THE PLATE SHOULD BE SIMILAR IN THICKNESS.
• ARRANGE ALL FOOD COMPONENTS EVENLY ON THE PLATE.
• AVOID EXCESSIVE OVERLAPPING OF PRODUCT.
• SAUCES MUST BE HEATED AND ADDED TO PRODUCT AFTER REHEATING.
• A MIXED VARIETY OF MEALS CAN BE REHEATED AT THE SAME TIME.
• À LA CARTE RETHERMALIZATION
required. Follow internal temperature requirements
À la carte rethermalization is designed to take
a single plate from a refrigerated temperature to
serving temperature for immediate service. Plates
are prepared in advance, covered, and refrigerated.
Preheat the Combitherm oven. Remove plate from
refrigeration and place in the oven at 275°F (135°C)
for an uncovered plate or 300°F (150°C) for a
covered plate. Plates with meat components will
take more time than plates containing all vegetable
components. Follow internal temperature
requirements for reheating and allow for override
time. After reheating, remove the plate from the
oven, add any sauces, garnish, and serve. This
process can be repeated as required.
for reheating and allow for override time. Remove
For the most efficient continuous service, it is
suggested that the Combitherm oven be dedicated to
the rethermalization process during serving hours.
• BANQUET RETHERMALIZATION
Banquet rethermalization is designed for high
volume, full or partial load (multiple plate) reheating.
For maximum efficiency, it is essential that volume
rethermalization be used in conjunction with the
utilization of holding cabinets to keep rethermalized
food at proper temperatures.
Plates are assembled in advance, covered, and
refrigerated or loaded on the roll-in cart and
refrigerated. Preheat the Combitherm oven at
275°F (135°C) for uncovered plates or 300°F (150°C)
for covered plates. Remove plates or the roll-in cart
from refrigeration, load in the oven and set timer as
the plates or roll-in cart from the Combitherm and
roll into the companion holding cabinet. Relocate
the holding cabinet to the banquet service area.
• RETHERMALIZING PREFABRICATED AND
VACUUM-PACKED FROZEN FOODS
For bulk product rethermalization, completely
defrost product bags in walk-in cooler. DO NOT
REMOVE PRODUCT FROM THE BAG. Load
thawed bags in preheated oven and rethermalize in
the Low Temperature Steam mode until the required
internal temperature is reached. Place rethermalized
bags in a preheated holding cabinet set at
140° to 165°F (60° to 74°C) until ready for service.
For large volume on-the-plate regeneration,
defrost bags in walk-in cooler. Open bags and plate
per menu requirements in a ( MAXIMUM ) 55°F (13°C)
refrigerated room. Cover plates, place on Alto-Shaam
roll-in cart (trolley), and roll into Combitherm oven
preheated at 275°F (135°C).
Regenerate in the Convection mode for 3 to 5
minutes. Switch to the Retherm mode for an
additional 3 minutes or more if required. Transfer
full trolley to a preheated holding cabinet set at
160°F (71°C) until ready for service. In the case of
meat cooked to rare, set the cabinet at 140°F (60°C).
PLATE COVERS MUST BE USED FOR ON-THE-PLATE REGENERATION.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 21
C O R E T E M P E R AT U R E P R O B E M O D E
A s a n a l t e r n a t i v e t o t i m e r o p e r a t i o n , t h e C o r e Te m p e r a t u r e P r o b e m o d e c a n
be used in conjunction with any program mode to cook by sensing internal
product temperature. For a more accurate inter nal temperature, a
specialized Combither m product probe senses temperature from four strategic
points and displays a temperature average.
PRESS THE ON/OFF POWER KEY TO THE ON POSITION.
INSERT THE PRODUCT PROBE.
The probe must be inserted so that the tip is positioned in the center of the food mass.
For liquid or semiliquid foods, suspend the probe in the center of the product and
secure the probe wire to the container edge.
SELECT AND PRESS THE REQUIRED COOKING PROGRAM.
PRESS THE TEMPERATURE KEY.
The cooking temperature will appear highlighted within the oven display.
Press the up and down arrow keys or rotate the adjustment knob to
select the desired cooking temperature within the temperature range of
the cooking mode selected.
PRESS THE CORE TEMP KEY.
The core temperature will appear highlighted within the oven display.
Press the up and down arrow keys or rotate the adjustment knob to
select the internal product cutoff temperature.
PRESS THE START KEY TO BEGIN THE COOKING MODE.
• The actual internal product temperature will appear in the display. To display the set internal product
temperature or to change the set values for core temperature during operation, press the
key once
and make corrections as required.
When the operator set internal temperature has been reached, a buzzer will sound indicating the end of
the operating mode.
• To stop the buzzer, press the start/stop key
or open the oven door.
To check the length of time the product has been operating in the core temperature mode, press and hold the
time key
along with the core temperature key
. The time period will appear at the top of the display.
CHEF OPERATING TIPS
To pr event over-cooking, r emove pr oduct fr om the oven as soon as the r equir ed inter nal
temperatur e is r eached in either the Cor e Temperatur e mode or the Cor e Temperatur e Delta-T
mode. The Cor e Temperatur e mode should not be used for cooking thin pr oduct items.
DO NOT USE THE PROBE WHEN COOKING THIN PRODUCTS.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 22
DELTA-T CORE TEMPERATURE COOKING
This special program function cooks by internal product temperature with the use of
the probe. Unlike the standard core temperature mode, however, the Delta-T oven
temperature automatically increases in direct proportion to the internal temperature
of the product. The Delta-T mode cooks with convection heat but provides a more
gentle method of cooking. Browning occurs toward the end of the cooking cycle.
PRESS THE ON/OFF POWER KEY TO THE ON POSITION.
PRESS THE CHEF FUNCTION KEY.
Press the up and down arrow keys or rotate the adjustment knob until the
Delta-T
symbol is highlighted in the display.
PRESS THE CHEF FUNCTION KEY.
Press the up and down arrow keys or rotate the
Delta-T
adjustment knob to select “ YES ” for the Delta-T function.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SETTING.
PRESS THE TEMPERATURE KEY.
Press the up and down arrow keys or rotate the adjustment knob to select the desired
Delta-T cooking temperature within the cooking temperature ranges shown below.
PRESS THE CORE TEMP KEY.
Press the up and down arrow keys or rotate the adjustment knob to select the
inter nal product cutoff temperature within the temperature ranges shown below.
PRODUCT
DELTA-T TEMPERATURE
CORE TEMPERATURE SETTING
BEEF ROAST
122°F to 131°F (50°C to 55°C)
118°F to 136°F (48°C to 58°C)
TENDERLOIN
122°F to 140°F (50°C to 60°C)
122°F to 140°F (50°C to 60°C)
VEAL & LAMB
122°F to 158°F (50°C to 70°C)
172°F (78°C)
PORK ROAST
122°F to 158°F (50°C to 70°C)
172°F (78°C)
HAM
122°F to 140°F (50°C to 60°C)
172°F (78°C)
THE OVEN WILL BEGIN THE DELTA-T CONVECTION
COOKING MODE.
The set Delta-T temperature will appear in the display.
The actual internal product temperature will appear in the display.
When the operator set inter nal temperature has been reached, a buzzer will sound indicating
the end of the operating mode.
• To stop the buzzer, press the start/stop key
or open the oven door.
DIFFERENCE BETWEEN COOKING COMPARTMENT TEMPERATURE
AND INTERNAL PRODUCT TEMPERATURE.
COOLING
COMPARTMENT
TEMPERATURE
INTERNAL
PRODUCT
TEMPERATURE
PRODUCT AND OVEN
TEMPERATURE START
INTERNAL PRDUCT
TEMPERATURE REACHED
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 23
AUXILIARY FUNCTIONS
CHEF FUNCTION KEY
There are several auxiliary functions available through the use of the Chef Function Key.
With the exception of the ability to add additional moisture to the oven compartment, that
can only be used during the convection mode, all additional functions can be engaged at any time during any
cooking mode. Chef Functions can also be programmed into a cooking procedure in oven models that
include the deluxe programmable feature. At the end of a cooking mode or program, the oven automatically
disengages all operator-set chef functions. These functions, however, do remain programmed and will
reengage the next time the programmed procedure is used.
P R E H E AT I N G
THE PREHEATING FUNCTION IS ENGAGED IN THE CONVECTION
MODE AT A FIXED
TEMPERATURE AND TIME. BOTH THE TEMPERATURE AND TIME CAN BE ADJUSTED BY THE
OPERATOR TO COMPLY WITH THE REQUIREMENTS OF THE INDIVIDUAL OPERATION.
.
SEE START UP PROCEDURES UNDER DEFAULT/MEMO SETTING
PRESS THE CHEF FUNCTION KEY.
Rotate the adjustment knob until the preheat symbol
is highlighted in the display.
PRESS THE CHEF FUNCTION KEY.
Press the up and down arrow keys
Preheating
or rotate the adjustment knob to select
“ YES ” for the Preheat function.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SETTING.
THE OVEN WILL BEGIN THE PREHEAT FUNCTION.
• The set preheat temperature will appear in the display.
• The set preheat time will appear in the display.
• The preheat symbol
will appear in the display.
When the set time and temperature has been reached, a buzzer will sound indicating
the end of the preheat function.
• To stop the buzzer, press the start/stop key
or open the oven door.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 24
AUXILIARY FUNCTIONS
CHEF FUNCTION KEY
GOLD-n-BROWN
The browning feature is an automatic function designed to regulate humidity for additional
color to products as needed. This feature is particularly useful for adding color to high moisture
products such as chicken and other poultry items or for additional browning of full loads and
other moist products. In addition, this feature may be used to add texture to fried items such as
French fries or breaded chicken. The browning feature can be used as required in both the
Combination mode and Convection mode and can be programmed into a cooking procedure.
Browning can be used for any product with a set cooking time more than 5-minutes.
Depending on the type of product and product load, the browning feature may also slightly
increase the set cooking time in order to fully complete the browning function. This is a
standard operating condition of this feature.
SELECT AND PRESS THE REQUIRED COOKING MODE AND SET MODE FUNCTIONS.
PRESS THE CHEF FUNCTION KEY.
R o t a t e t h e a d j u s t m e n t k n o b u n t i l t h e b ro w n i n g s y m b o l
is highlighted within
the display.
PRESS THE CHEF FUNCTION KEY.
Press the up and down arrow keys or rotate the
Brown
adjustment knob to select “ YES ” for the browning function.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SETTING.
The browning indicator light
will illuminate directly above the display.
PRESS THE START KEY.
The oven will engage the browning feature in the Combination or Convection mode set
by the operator.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 25
AUXILIARY FUNCTIONS
CHEF FUNCTION KEY
C O O L - D O W N F E AT U R E
The cool-down feature provides the operator with the ability to lower the temperature of the
oven compartment at an accelerated pace. This function is useful when it is necessary to immediately
change from a high temperature cooking function to a lower temperature function or to the steam program.
This function is also useful to help cool the oven compartment in preparation for cleaning.
CHEF OPERATING TIP
When using the cool-down feature in preparation for cleaning, it is important to remember
the temperature in the display indicates the air temperature inside the oven compartment
and not the interior walls of the oven. Always make certain to allow the oven walls to cool
to a minimum of 140°F (60°C) before spraying the compartment with oven cleaner.
PRESS THE CHEF FUNCTION KEY.
Rotate the adjustment knob until the cool-down symbol
is highlighted in the display.
PRESS THE CHEF FUNCTION KEY.
Press the up and down arrow keys
Cool Down
or rotate the adjustment knob to select
“ YES ” for the cool-down function.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SETTING.
OPEN THE OVEN DOOR.
The display will indicate the current temperature of the oven.
ROTATE THE ADJUSTMENT KNOB TO SELECT A COOL-DOWN TEMPERATURE WITHIN A
RANGE OF 212°F TO 68°F (100°C TO 20°C).
THE FACTORY SET DEFAULT IS
122°F (50°C).
The displayed temperature will continue to decline until it reaches the operator set
temperature or factory default temperature if not selected by the operator.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 26
AUXILIARY FUNCTIONS
CHEF FUNCTION KEY
R E D U C E D FA N S P E E D
The reduced fan speed function is useful for flow-sensitive products such as soufflês and
meringues, or any products affected by a high velocity of air movement.
SELECT AND PRESS THE REQUIRED COOKING MODE AND SET MODE FUNCTIONS.
PRESS THE CHEF FUNCTION KEY.
Rotate the adjustment knob until the fan symbol
is highlighted in the display.
PRESS THE CHEF FUNCTION KEY.
Press the up and down arrow keys or rotate
Redc’d fan speed
t h e a d j u s t m e n t k n o b t o s e l e c t “ YES ” f o r t h e r e d u c e d
fan speed function.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SETTING.
The reduced fan speed indicator light
will illuminate directly above the display.
PRESS THE START KEY.
The oven will start at a reduced fan speed in whatever cooking mode set by the operator.
REDUCED POWER
ELECTRIC MODELS ONLY
The reduced power function can be used to reduce kitchen power peaks and energy consumption.
SELECT AND PRESS THE REQUIRED COOKING MODE AND SET MODE FUNCTIONS.
PRESS THE CHEF FUNCTION KEY.
Rotate the adjustment knob until the reduced power symbol
is highlighted
in the display.
PRESS THE CHEF FUNCTION KEY.
Press the up and down arrow keys or rotate
Redc’d power
t h e a d j u s t m e n t k n o b t o s e l e c t “ YES ” f o r t h e r e d u c e d
power function.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SETTING.
PRESS THE START KEY.
The oven will operate with reduced power in whatever cooking mode set by the operator.
REDUCED POWER WILL RESULT IN LONGER COOKING TIMES.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 27
AUXILIARY FUNCTIONS
CHEF FUNCTION KEY
OPERATING ELEMENTS THAT
CANNOT BE LOCKED
KEY LOCK
Except as noted, all of the mode keys and
functions available on the Combitherm can be
locked to prevent unauthorized or accidental
changes to the settings.
PRESS THE CHEF FUNCTION KEY.
R o t a t e t h e a d j u s t m e n t k n o b u n t i l t h e k e y s y mb o l
is highlighted within the display.
PRESS THE CHEF FUNCTION KEY.
Press the up and down arrow keys or rotate the
Key lock
adjustment knob to select “ YES ” for the key lock function.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SETTING.
The display will indicate PIN 000.
ROTATE THE ADJUSTMENT KNOB TO PIN 000.
➯ PIN 000 is the factory set default to prevent an accidental lock or unlock of the control functions.
PRESS THE CHEF FUNCTION KEY.
THE DISPLAY WILL INDICATE “ALL KEYS UNLOCKED.”
SELECT AND PRESS THE FIRST
CONTROL FUNCTION TO BE LOCKED.
The display will indicate “LOCK.”
If the wrong key has been selected and locked in error, press the same control key again and
“UNLOCK” will appear in the display.
Continue in this manner until all desired control functions are locked.
PRESS THE START KEY TO CONFIRM THE LOCKING FUNCTION.
Whenever any control function has been locked, the key lock symbol will be illuminated within the display.
Whenever any locked control function is pressed, the key lock symbol will flash and an
audible signal will sound.
KEY UNLOCK
FOLLOW THE SAME PROCEDURE AS ABOVE UNTIL THE DISPLAY INDICATES “ALL KEYS UNLOCKED.”
To u n l o c k t h e C h e f F u n c t i o n
key.
PRESS THE POWER KEY TO TURN THE OVEN OFF.
PRESS THE CHEF FUNCTION KEY
ROTATE THE ADJUSTMENT KNOB TO PIN 000 TO DISENGAGE ALL LOCK FUNCTIONS.
PRESS THE CHEF FUNCTION KEY. THE DISPLAY WILL INDICATE “ALL KEYS UNLOCKED.”
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 28
AUXILIARY FUNCTIONS
CHEF FUNCTION KEY
STEAM INJECTION
Additional steam can be added to the cooking compartment at any time when cooking in the
convection mode.
STEAM INJECTION CANNOT BE PROGRAMMED
T H R O U G H T H E U S E O F T H E C O N T R O L K E Y PA D B U T
CAN BE PROGRAMMED THROUGH OPTIONAL
K I T C H E N M A N A G E M E N T S O F T WA R E .
PRESS THE CHEF FUNCTION KEY.
Rotate the adjustment knob until the steam injection symbol
i s h i g h l i g h te d w i t h i n
the display.
PRESS THE CHEF FUNCTION KEY.
Press the up and down arrow keys or rotate
Add moisture
the adjustment knob to select “ YES ” for the steam
injection function.
PRESS THE CHEF FUNCTION KEY TO ACTIVATE THE STEAM INJECTION FUNCTION.
Additional steam is injected into the oven compartment for a time period of
approximately 15 seconds.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 29
A D VA N C E F E AT U R E S
MOISTURE VENT KEY
This function provides the operator with the ability to eliminate excessive moisture from
the oven compartment and the exterior surface of the foods being cooked. The moisture
vent key is designed to operate in both the Combination mode and in the Convection
cooking mode. On deluxe models, this function can also be made part of a cooking program.
PRESS THE MOISTURE VENT KEY TO REDUCE STEAM AND MOISTURE LEVELS IN THE OVEN.
The illuminated, blue portion of the Moisture Vent Key will go out. Open vent
within the display.
symbol will illuminate
PRESS THE MOISTURE VENT KEY TO DISENGAGE THE MOISTURE VENT KEY FUNCTION.
The blue portion of the Moisture Vent Key will illuminate. Open vent
will extinguish.
symbol within the display
AT THE END OF A COOKING MODE, THE MOISTURE VENT KEY WILL AUTOMATICALLY DISENGAGE.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 30
A D VA N C E F E AT U R E S
QUICK PROGRAMMING
This quick programming function provides the operator with the ability to temporarily program a cooking
procedure using multiple cooking modes, along with any auxiliary functions desired. Quick programming is
particularly useful when cooking several batches of the same product back-to-back and will remain
programmed until any new cooking mode key is pressed.
PRESS AND HOLD THE FIRST REQUIRED COOKING MODE FOR A PERIOD OF 3-SECONDS.
01/01 will appear at the top of the display indicating STEP ONE.
The temperature and time will appear directly below 01/01.
PRESS THE TEMPERATURE KEY.
The temperature will become highlighted within the display.
ROTATE THE ADJUSTMENT KNOB TO SELECT THE REQUIRED TEMPERATURE.
PRESS THE TIME KEY OR THE CORE TEMP KEY
.
The time or core temperature will become highlighted within the display.
ROTATE THE ADJUSTMENT KNOB TO SELECT THE REQUIRED SETTING.
PRESS AND HOLD THE SECOND REQUIRED COOKING MODE FOR A PERIOD OF 3-SECONDS.
Follow the above directions until all steps have been entered.
PRESS THE START KEY.
The oven will begin cooking as programmed, automatically switching to each cooking
mode entered. Each step entered will be indicated in the display as the oven cycles from
mode to mode. E X A M P L E : 0 1 / 0 5 = S T E P O N E O F F I V E
02/05 = STEP TWO OF FIVE
PRESS THE STOP KEY OR OPEN THE OVEN DOOR WHEN THE BUZZER SOUNDS AT THE END
OF THE PROGRAM.
THIS PROGRAM WILL REMAIN IN TEMPORARY MEMORY UNTIL ANY NEW
COOKING MODE KEY IS PRESSED. QUICK PROGRAMMING CAN BE SAVED AND
STORED IN MEMORY ON DELUXE MODELS ONLY.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 31
A D VA N C E F E AT U R E S
Auxiliary Functions are made part of the control as an additional convenience to the operator, however,
these functions are not necessary for the general operation of the Combitherm oven.
START TIME PRESELECT
Start time preselect provides the operator with the ability
to program a fixed start time for oven operation. This
function can be operated when cooking in any mode and
is offered as a convenience to set an advanced start-up of
the preheating function prior to the beginning of the
production day. It can also be used for advance start-up
for non-refrigerated items such as baked potatoes.
To prevent food spoilage, this feature
is not recommended for use with any
raw product that requires temperature
maintenance at or under 40°F (4°C).
SELECT AND PRESS THE REQUIRED COOKING MODE.
Set all mode functions such as temperature, time, core temperature, etc.
The time entered in the initial operational mode setup will automatically be
reflected on the start time preselect display.
PRESS AND HOLD THE TIME KEY WHILE TURNING THE ADJUSTMENT KNOB.
The display will indicate the current programmed settings in 24-hour (military) time.
A.M.
01:00
00:48
OVEN START
IN 48 MINUTES
10:23 11:23
STARTING TIME
10:23 A.M.
ENDING TIME
11:23 A.M.
1-HOUR TOTAL
COOKING TIME
P.M.
1:00
1:00
1:00 13:00
2:00
2:00
2:00 14:00
3:00
3:00
3:00 15:00
4:00
4:00
4:00 16:00
5:00
5:00
5:00 17:00
6:00
6:00
6:00 18:00
7:00
7:00
7:00 19:00
8:00
8:00
8:00 20:00
9:00
9:00
9:00 21:00
10:00 10:00 10:00 22:00
11:00 11:00 11:00 23:00
12:00 12:00 12:00 24:00
The cooking time shown ( UPPER RIGHT ) indicates automatic oven operation for a period of one hour and
appears only when cooking by time as entered in the initial operational mode setup.
TO CHANGE THE STARTING TIME, PRESS AND HOLD THE TIME KEY AND TURN THE
ADJUSTMENT KNOB.
Rotate the adjustment knob to select the starting time desired. As the starting time is
changed, the countdown for oven start ( LEFT ) and the ending time will automatically
adjust accordingly.
RELEASE THE TIME KEY AFTER THE REQUIRED STARTING TIME HAS BEEN SELECTED.
The oven preselect start time display will immediately begin a countdown and will
automatically start the oven when zero is reached.
THIS FUNCTION CAN BE CANCELLED AT ANY TIME BY PRESSING THE START/STOP KEY
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 32
.
PROGRAM FUNCTION
COMBITHERM PROGRAMMING SYMBOLS
RECORD
COPY PROCEDURE
INSERT STEP
SAVE
DELETE PROCEDURE
APPEND STEP
NEW PROCEDURE
EDIT PROCEDURE
DELETE STEP
RECORDING A COOKING PROCEDURE
Recording a cooking procedure provides the operator with the ability to test and
verify all set operating parameters for the selected cooking modes and to make any
necessary adjustments before saving and storing the procedure into memory.
PRESS THE PROGRAM INSTALL AND EDIT KEY.
Press the up and down arrow keys or ro t a t e t h e a d j u s t m e n t
knob until the record symbol
is highlighted in the display.
PRESS THE PROGRAM INSTALL KEY TO CONFIRM THE SELECTION.
The display will indicate “Recorder ON” and the record symbol
will appear in the display.
SELECT AND PRESS THE FIRST REQUIRED COOKING MODE.
Set all cooking mode parameters for temperature, time, or internal product temperature
plus auxiliary functions, and advanced features for the first step to be recorded.
PRESS THE START KEY TO BEGIN THE FIRST RECORDED STEP.
When the cooking time has expired or the operator set internal temperature has been reached, a buzzer will
sound indicating the end of the operating mode.
• To stop the buzzer, press the start/stop key
or open the oven door.
SELECT AND PRESS THE SECOND REQUIRED COOKING MODE.
Set all cooking mode parameters for temperature, time, or internal product temperature
plus auxiliary functions, and advanced features for the second step to be recorded.
PRESS THE START KEY TO BEGIN THE SECOND RECORDED STEP.
Continue to record cooking modes as indicated for up to 20 steps.
All cooking mode steps entered with “Recorder ON” will remain in memory, in the order entered, until the recorder is
turned off. Recorded procedures will not be lost or affected by pressing the stop/start key
.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 33
PROGRAM FUNCTION
TO CANCEL THE RECORDING FUNCTION
WITH THE “Recorder ON” FUNCTION ACTIVATED, PRESS THE PROGRAM INSTALL AND EDIT KEY.
Press the up and down arrow keys or r o t a t e t h e a d j u s t m e n t k n o b u n t i l t h e r e c o r d
symbol
is highlighted in the display.
PRESS THE PROGRAM INSTALL KEY TO CONFIRM THE SELECTION.
“Recorder OFF” will appear in the display and the oven can be operated normally.
S AV I N G A R E C O R D E D C O O K I N G P R O C E D U R E
When the previous cooking mode steps recorded produce satisfactory results, the recorded
cooking procedure can be saved in memory for future use.
PRESS THE PROGRAM INSTALL/EDIT KEY.
Press the up and down arrow keys or rotate the
adjustment knob until the save symbol
is highlighted in the display.
PRESS THE PROGRAM INSTALL/EDIT KEY TO CONFIRM THE SELECTION.
Name the procedure. Rotate the adjustment knob to select the first letter
of the procedure name. Press the up and down arrow key to select
second letter position and rotate the adjustment knob to select the second
A
—
—
—————
letter. Continue this procedure for each subsequent alpha character,
number, or symbol required.
PRESS THE PROGRAM INSTALL AND EDIT KEY TO CONFIRM THE PROCEDURE NAME.
The display will indicate the first unoccupied memory location within the programmed menu.
If an alternate location is desired, rotate the adjustment knob to highlight another unoccupied,
numbered memory location within the programmed menu. If an occupied location is selected,
the existing procedure will be replaced by the new procedure.
PRESS THE PROGRAM INSTALL/EDIT KEY TO CONFIRM THE PROCEDURE LOCATION.
The display will indicate “please wait” and will return to the main menu display.
The procedure has now been saved in the selected location and can be verified by rotating the
adjustment knob to the saved procedure.
To review the set operating parameters of any programmed procedure, press the programmed menu
key
and rotate the adjustment knob until the procedure to be reviewed is highlighted in the display. Press the chef
function
key. The cooking mode key for the first step will illuminate and the program mode, temperature,
time, or core temperature will appear in the display. Rotate the adjustment knob to review each step.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 34
PROGRAM FUNCTION
C R E AT I N G A N E W C O O K I N G P R O C E D U R E
Cooking procedures for items prepared on a regular basis can be stored in memory.
PRESS THE PROGRAM INSTALL/EDIT KEY.
Press the up and down arrow keys or rotate the adjustment knob until the new procedure
symbol
is highlighted in the display.
PRESS THE PROGRAM INSTALL/EDIT KEY TO CONFIRM THE SELECTION.
All cooking mode keys will begin to flash and 01/01 will appear at the top of the
display indicating the first cooking step.
SELECT AND PRESS THE FIRST REQUIRED COOKING MODE.
Set cooking mode functions for temperature and time, or internal core temperature. Add any auxiliary functions
along with the moisture venting feature. Follow the basic operating instructions located in this booklet. Auxiliary
functions can be added by pressing the chef function
key after entering the operating mode parameters for
each individual step and pressing the up and down arrow keys or rotating the adjustment knob to select the
auxiliary function required. Press the chef function key to confirm the auxiliary function setting(s) for each step.
PRESS THE PROGRAM INSTALL/EDIT KEY TO CONFIRM THE FIRST STEP.
SELECT AND PRESS THE SECOND REQUIRED COOKING MODE.
The display will indicate 02/02 indicating the second cooking mode step.
Set all cooking mode functions as indicated above.
PRESS THE PROGRAM INSTALL/EDIT KEY TO CONFIRM THE SECOND STEP.
CONTINUE WITH THE ABOVE INSTRUCTIONS UNTIL ALL MODE STEPS AND FUNCTIONS ARE ENTERED.
UP TO 20 COOKING MODE STEPS CAN BE SAVED IN A SINGLE PROCEDURE.
AFTER ALL FUNCTIONS ARE ENTERED,
PRESS THE PROGRAM INSTALL/EDIT KEY TO CONFIRM THE NEW PROCEDURE.
Name the procedure. Rotate the adjustment knob to select
the first letter of the procedure name. Press the up and
down arrow key to select second letter position and rotate
t h e a d j u s t m e n t k n o b t o s e l e c t t h e s e c o n d l e t t e r. C o n t i n u e f o r
e a c h s u b s e q u e n t a l p h a c h a r a c t e r, n u m b e r, o r s y m b o l r e q u i r e d .
A
—
—
—————
PRESS THE PROGRAM INSTALL AND EDIT KEY TO CONFIRM THE PROCEDURE NAME.
Rotate the adjustment knob to highlight an unoccupied, numbered memory location within the
programmed menu. If an occupied location is selected, the existing procedure will be
replaced by the new procedure.
PRESS THE PROGRAM INSTALL AND EDIT KEY TO CONFIRM THE PROGRAM INSTALLATION.
The display will indicate “please wait” and will return to the main menu display.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 35
PROGRAM FUNCTION
S TA R T A P R O G R A M M E D P R O C E D U R E
PRESS THE PROGRAMMED MENU KEY.
All stored procedures are listed alphabetically or numerically as selected by the
operator in the initial oven start up procedures under the program index category.
Rotate the adjustment knob until the required procedure is highlighted in the display.
PRESS THE START KEY.
To
review
the
set
pr ogrammed menu
parameters
of
any
programmed
procedure,
press
the
key and r otate the adjustment knob until the pr ocedur e to
be r eviewed is highlighted in the display. Pr ess the chef function
key. The
cooking mode, temperatur e, time, or cor e temperatur e will appear in the display.
COPY A PROGRAMMED PROCEDURE
PRESS THE PROGRAMMED MENU KEY.
Rotate the adjustment knob until the procedure to be copied is highlighted in the display.
PRESS THE PROGRAM INSTALL AND EDIT KEY.
Press the up and down arrow keys or ro t a t e t h e a d j u s t m e n t k n o b u n t i l t h e
procedure symbol is highlighted in the display.
copy»
PRESS THE PROGRAM INSTALL AND EDIT KEY.
The display will select an empty, numbered location to insert the duplicate copy.
PRESS THE PROGRAM INSTALL AND EDIT KEY TO CONFIRM THE DUPLICATION.
The display will indicate “please wait” and will return to the main menu display.
An exact duplicate of the selected procedure has been inserted in the new location under the same name as the
original procedure. The duplicate can be renamed and edited as required. See additional editing instructions.
DELETE A PROGRAMMED PROCEDURE
PRESS THE PROGRAMMED MENU KEY.
Rotate the adjustment knob to highlight the procedure to be deleted.
PRESS THE PROGRAM INSTALL/EDIT KEY.
Press the up and down arrow keys or rotate the adjustment
knob until the delete
symbol is highlighted in the display.
PRESS THE PROGRAM INSTALL AND EDIT KEY TO CONFIRM THE SELECTION.
The programmed procedure has been deleted from the menu.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 36
PROGRAM FUNCTION
PROGRAM EDITING
EDIT A PROGRAMMED PROCEDURE
PRESS THE PROGRAMMED MENU KEY.
Rotate the adjustment knob until the procedure to be edited is highlighted in the display.
PRESS THE PROGRAM INSTALL AND EDIT KEY.
Press the up and down arrow keys or rotate the adjustment knob until
the edit symbol is highlighted in the display.
PRESS THE PROGRAM INSTALL AND EDIT KEY TO CONFIRM THE SELECTION.
The display will indicate the procedure name, cooking step number
(EXAMPLE: “01/05” = STEP ONE OF FIVE), and operating parameters
for temperature, time, or internal product temperature.
To change the operating parameters for the first step:
Press the cooking temperature
key and rotate the adjustment knob.
Press the time
key and rotate the adjustment knob to change the cooking time.
Press the core temperature
key and rotate the adjustment knob to change the core temp.
Auxiliary functions can be added by pressing the chef function
key after entering the
operating mode parameters for each individual step and pressing the up and down arrow
keys or rotate the adjustment knob to select the auxiliary function required. Press the chef
function key to confirm the auxiliary function setting.
Press the down arrow key for each subsequent step of the procedure and make changes to
each step as required.
PRESS THE PROGRAM INSTALL AND EDIT KEY TO CONFIRM THE SETTING.
The display will indicate the same name as the original procedure, minus the last letter. Install
the last letter by rotating the adjustment knob to the correct letter.
Rename the procedure by pressing the down arrow key to clear the display.
Press the up and down arrow key to select each individual alpha character, number,
or symbol. Rotate the adjustment knob to select each subsequent letter.
PRESS THE PROGRAM INSTALL AND EDIT KEY TO CONFIRM THE NAME.
PRESS THE PROGRAM INSTALL AND EDIT KEY TO INSTALL THE PROGRAM.
To review the set operating parameters of any programmed procedure, press the programmed menu
key
and rotate the adjustment knob until the procedure to be reviewed is highlighted in the display. Press the chef
function
key. The cooking mode key for the first step will illuminate and the program mode, temperature,
time, or core temperature will appear in the display. Rotate the adjustment knob to review each step.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 37
PROGRAM FUNCTION
PROGRAM EDITING
INSERT A PROGRAMMED PROCEDURE STEP
PRESS THE PROGRAMMED MENU KEY.
Rotate the adjustment knob until the procedure to add a new step is highlighted in the display.
PRESS THE PROGRAM INSTALL KEY.
Press the up and down arrow keys or rotate the adjustment knob until
the edit procedure
symbol is highlighted in the display.
PRESS THE PROGRAM INSTALL AND EDIT KEY TO CONFIRM THE SELECTION.
The display will indicate the procedure name, cooking step number and
operating parameters for temperature, time, or internal product temperature.
Press the up or down arrow keys to select the step
immediately following the position wanted for the new step.
P R E S S T H E C H E F F U N C T I O N K E Y.
A choice of editing symbols and auxiliary functions will appear in the
display. Press the up and down arrow keys or rotate the adjustment
knob to select the insert step
symbol.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SELECTION.
Press the up and down arrow keys or rotate the
Insert step ?
adjustment knob to select “YES” for step insertion.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SELECTION.
All cooking modes will begin to flash. Select and press the cooking mode to be inserted. Press and set
cooking temperature, time, or internal core temperature. Auxiliary functions can be added by pressing the
chef function
key after entering the operating mode parameters for each individual step and pressing the
up and down arrow keys or rotating the adjustment knob to select the auxiliary function required. Press
the chef function key to confirm the auxiliary function setting. Add the moisture vent key function if required.
P R E S S T H E I N S TA L L / E D I T K E Y T O C O N F I R M T H E S E L E C T E D M O D E A N D F U N C T I O N S .
T h e d i s p l a y w i l l i n d i c a t e t h e p r o c e d u r e n a m e m i n u s t h e l a s t l e t t e r. R e i n s e r t t h e l a s t
letter with the adjustment knob or use t h e u p a n d d o w n a r r o w k e y s i n
conjunction with the adjustment knob to rename the procedure.
P R E S S T H E I N S TA L L / E D I T K E Y T O C O N F I R M T H E N A M E .
P R E S S T H E I N S TA L L / E D I T K E Y T O I N S E R T T H E N E W S T E P I N T O T H E P R O C E D U R E .
The display will indicate “please wait” and will return to the main menu display.
T O V E R I F Y T H E I N S E R T E D S T E P, P R E S S T H E C H E F F U N C T I O N K E Y
W H I L E T H E A LT E R E D P R O C E D U R E I S H I G H L I G H T E D . R O TAT E T H E
A D J U S T M E N T K N O B T O R E V I E W A L L S E T PA R A M E T E R S .
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 38
PROGRAM FUNCTION
PROGRAM EDITING
APPEND A PROGRAMMED PROCEDURE STEP
PRESS THE PROGRAMMED MENU KEY.
Rotate the adjustment knob until the procedure to include a final step is highlighted in the display.
PRESS THE PROGRAM INSTALL KEY.
Press the up and down arrow keys or rotate the adjustment knob until
the edit procedure
symbol is highlighted in the display.
PRESS THE PROGRAM INSTALL AND EDIT KEY TO CONFIRM THE SELECTION.
The display will indicate the procedure name, cooking step number and
operating parameters for temperature, time, or inter nal product temperature.
Press the up or down arrow keys to select the last step
of the procedure.
P R E S S T H E C H E F F U N C T I O N K E Y.
A choice of editing symbols and auxiliary functions will appear in the
display. Press the up and down arrow keys or rotate the adjustment
knob to select the append step
symbol.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SELECTION.
Press the up and down arrow keys or rotate
Append step ?
the adjustment knob to select “YES” for append step.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SELECTION.
All cooking modes will begin to flash. Select and press the cooking mode to be appended. Press and set
cooking temperature, time, or internal core temperature. Auxiliary functions can be added by pressing the
chef function
key after entering the operating mode parameters for each individual step and pressing the
up and down arrow keys or rotating the adjustment knob to select the auxiliary function required. Press
the chef function key to confirm the auxiliary function setting. Add the moisture vent key function if required.
P R E S S T H E I N S TA L L / E D I T K E Y T O C O N F I R M T H E S E L E C T E D M O D E A N D F U N C T I O N S .
T h e d i s p l a y w i l l i n d i c a t e t h e p r o c e d u r e n a m e m i n u s t h e l a s t l e t t e r. R e i n s e r t t h e l a s t
letter with the adjustment knob or use t h e u p a n d d o w n a r r o w k e y s i n
conjunction with the adjustment knob to rename the procedure.
P R E S S T H E I N S TA L L / E D I T K E Y T O C O N F I R M T H E N A M E .
P R E S S T H E I N S TA L L / E D I T K E Y T O I N S E R T T H E N E W S T E P I N T O T H E P R O C E D U R E .
The display will indicate “please wait” and will return to the main menu display.
TO VERIFY THE INSERTED STEP, PRESS THE CHEF FUNCTION KEY WHILE THE ALTERED PROCEDURE
IS HIGHLIGHTED. ROTATE THE ADJUSTMENT KNOB TO REVIEW ALL SET PARAMETERS.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 39
PROGRAM FUNCTION
PROGRAM EDITING
DELETE A PROGRAMMED STEP
PRESS THE PROGRAMMED MENU KEY.
Rotate the adjustment knob to highlight the procedure in which a step is to be deleted.
PRESS THE PROGRAM INSTALL KEY.
Press the up and down arrow keys or rotate the adjustment knob until
the edit procedure
symbol is highlighted in the display.
PRESS THE PROGRAM INSTALL AND EDIT KEY TO CONFIRM THE SELECTION.
The display will indicate the procedure name, cooking step number and
operating parameters for temperature, time, or inter nal product temperature.
Press the up or down arrow keys to select the step to be deleted.
P R E S S T H E C H E F F U N C T I O N K E Y.
A choice of editing symbols and auxiliary functions will appear in the
display. Press the up and down arrow keys or rotate the adjustment
knob to select the delete step
symbol.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SELECTION.
Press the up and down arrow keys or rotate
Delete step ?
the adjustment knob to select “YES” for step deletion.
PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SELECTION.
P R E S S T H E I N S TA L L / E D I T K E Y T O C O N F I R M T H E D E L E T I O N .
The display will indicate the name of the procedure as originally programmed.
P R E S S T H E I N S TA L L / E D I T K E Y T O C O N F I R M T H E N A M E .
P R E S S T H E I N S TA L L / E D I T K E Y T O R E M O V E T H E D E L E T E D S T E P F R O M T H E P R O G R A M .
The display will indicate “please wait” and will retur n to the main menu display.
TO VERIFY THE STEP HAS BEEN DELETED, PRESS THE CHEF FUNCTION
KEY WHILE THE DELETE STEP PROCEDURE IS HIGHLIGHTED. ROTATE
THE ADJUSTMENT KNOB TO REVIEW ALL SET PARAMETERS.
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 40
PROGRAM FUNCTION
RAPID-TOUCH™ KEYS
Rapid-Touch programmed quick-keys provide the operator with the
ability to assign procedures used on a regular basis to individual keys
that can be identified with a picture graphic resembling the product.
Various picture graphics are included with the Combitherm oven.
TO ASSIGN A PROCEDURE TO A PROGRAM RAPID-TOUCH KEY
PRESS THE PROGRAMMED MENU KEY.
Rotate the adjustment knob to highlight the procedure to be assigned to Rapid-Touch operation.
PRESS AND HOLD THE SELECTED RAPID TOUCH KEY FOR A PERIOD OF THREE SECONDS.
When the buzzer sounds, the programmed procedure
h a s b e e n a s s i g n e d t o t h e R a p i d - To u c h k e y s e l e c t e d .
I d e n t i f y t h e R a p i d - To u c h k e y w i t h a c o r r e s p o n d i n g p i c t u r e g r a p h i c .
T O O P E R AT E A P R O C E D U R E O N R A P I D - T O U C H K E Y
PRESS AN ASSIGNED RAPID TOUCH KEY.
The indicator light to the upper right of the selected Rapid-Touch key will
illuminate. The oven will begin operating as programmed with the display
indicating the name of the procedure, the step number, the total number
of steps, and the temperature, time, or internal product temperature.
01/02 ROAST CHICKEN
When the cooking time for all programmed modes has expired or the operator set internal temperature has
been reached, a buzzer will sound indicating the completion of the program.
• To stop the buzzer, press the start/stop key
or open the oven door.
O n c e a R a p i d - To u c h k e y i s p r o g r a m m e d w i t h a p r o c e d u r e , c a r e s h o u l d b e t a k e n n o t t o
press and hold the programmed key with another procedure highlighted in the display
by means of the programmed menu key. The highlighted procedure will override the
R a p i d - To u c h k e y p r o g r a m a n d t h e p i c t u r e g r a p h i c w i l l n o l o n g e r m a t c h t h e p r o c e d u r e .
S E C T I O N 1 – C O N T R O L PA N E L I D E N T I F I C AT I O N • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 41
2
PREVENTIVE MAINTENANCE
Routine Cleaning ..........................................................................
43
Steam Generator Flush..................................................................
49
Decalcification ..............................................................................
50
Return to Main Table of Contents ..................................................
3
S E C T I O N 2 – P R E V E N T I V E M A I N T E N A N C E • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 42
PREVENTIVE MAINTENANCE
Preventive Maintenance
In addition to the routine cleaning and maintenance procedures, there are several additional steps to be
taken for both sanitation purposes and to keep the oven running at top operating efficiency. These
additional safeguards will help prevent inconvenient down time and costly repairs.
● D O N O T D I S P O S E O F G R E A S E , FAT, O R S O L I D WA S T E D O W N T H E O V E N D R A I N .
Fats and solids will eventually coagulate in the drain system, causing blockage. Consequently, water
will back-up into the condenser and interior oven compartment, resulting in an oven that is inoperable.
● MAKE CERTAIN THE DRAIN SCREEN IS ALWAYS IN PLACE. REMOVE ANY SOLID
WASTE MATERIAL FROM THE DRAIN SCREEN BEFORE IT ENTERS THE DRAIN SYSTEM.
The routine removal of solids from the drain screen will help prevent blockage.
● U S E T H E A U T H O R I Z E D C O M B I T H E R M O V E N C L E A N E R O N LY . T h e u s e o f u n a u t h o r i z e d
cleaning agents may discolor or har m the interior sur faces of the oven.
● TO PROLONG THE LIFE OF THE DOOR GASKET, REMOVE AND CLEAN THIS ITEM DAILY.
The acids and related compounds found in fat, particularly chicken fat, will weaken the
composition of the gasket unless cleaned on a daily basis.
● T O A D D I T I O N A L LY P R O T E C T G A S K E T L I F E , A L L O W O V E N D O O R T O R E M A I N
S L I G H T LY O P E N AT T H E E N D O F T H E P R O D U C T I O N D AY. A n o p e n d o o r w i l l r e l i e v e
the pressure on the door gasket.
● ROUTINELY CLEAN DOOR HINGES. Open oven door to relieve tension. Clean all parts of the hinge.
R O L L - I N C A R T / F O O D T R O L L E Y C L E A N I N G (ON
EQUIPPED MODELS
)
1.
Remove food trolley to a cart wash area. Trolleys may be cleaned using any mild
cleaning detergent and warm water.
2.
Hand wipe all framing, slides, drip pan, and base. Thoroughly clean debris from
the casters. A spray hose can be used for easier cart cleaning.
3.
Remove detergent solution with warm water.
4.
Wipe or spray with a sanitizing solution designed for use on metal and vinyl food
contact surfaces.
5.
Allow trolley to air dry.
As an alternative, trolleys can be sprayed with Combitherm liquid oven
cleaner while inside the oven. Allow the trolley to remain in the oven
through the normal cleaning cycle, followed by steps 2 through 5 above.
S E C T I O N 2 – P R E V E N T I V E M A I N T E N A N C E • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 43
PREVENTIVE MAINTENANCE
P R O T E C T I N G S TA I N L E S S
S T E E L S U R FA C E S
CLEANING AGENTS
It is important to guard
against corrosion in the care
of stainless steel surfaces.
Harsh, corrosive, or
inappropriate chemicals can
completely destroy the
protective surface layer of
stainless steel. Abrasive pads, steel wool, or metal
implements will abrade surfaces causing damage to
this protective coating and will eventually result in
areas of corrosion. Even water, particularly hard
water that contains high to moderate concentrations
of chloride, will cause oxidation and pitting that
result in rust and corrosion. In addition, many acidic
foods spilled and left to remain on metal surfaces are
contributing factors that will corrode surfaces.
Proper cleaning agents, materials, and methods are
vital to maintaining the appearance and life of this
appliance. Spilled foods should be removed and the
area wiped as soon as possible but at the very least,
a minimum of once a day. Always thoroughly rinse
surfaces after using a cleaning agent and wipe
standing water as quickly as possible after rinsing.
USE AUTHORIZED COMBITHERM
LIQUID OVEN CLEANER ONLY
Cleaning agents must be chloride-free compounds
and must not contain quaternary salts. Never use
hydrochloric acid (muriatic acid) on stainless steel
surfaces. Unauthorized cleaning agents may discolor
or harm interior surfaces of the oven. Read and
understand label and material safety data sheet
before using the oven cleaner.
C L E A N I N G M AT E R I A L S
The cleaning function can
usually be accomplished with
the proper cleaning agent
and a soft, clean cloth. When
more aggressive methods
must be employed, use a
non-abrasive scouring pad on
difficult areas and make
certain to scrub with the
visible grain of surface metal to avoid surface
scratches. Never use wire brushes, metal scouring
pads, or scrapers to remove food residue.
TO PROTECT STAINLESS STEEL
SURFACES, COMPLETELY AVOID
THE USE OF ABRASIVE
CLEANING COMPOUNDS,
CHLORIDE BASED CLEANERS, OR
CLEANERS CONTAINING
QUATERNARY SALTS. NEVER USE
HYDROCHLORIC ACID (MURIATIC
ACID) ON STAINLESS STEEL.
NEVER USE WIRE BRUSHES,
METAL SCOURING PADS OR
SCRAPERS.
S E C T I O N 2 – P R E V E N T I V E M A I N T E N A N C E • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 44
PREVENTIVE MAINTENANCE
Establishing a routine cleaning and maintenance schedule will help keep the Combitherm oven running at top
operating efficiency and is an absolutely essential part of a comprehensive sanitation program. Good
equipment maintained and kept clean works better and lasts longer. PROTECT YOUR INVESTMENT.
D A I LY G A S K E T C L E A N I N G
D A I LY O V E N C L E A N I N G
It is important to prolong
To be performed at the end of the production day or
the life of the oven gasket
between production shifts.
by cleaning this item on a
daily basis. Routine
cleaning will help protect
D A I LY S T E A M G E N E R AT O R F L U S H
(E L E C T R I C B O I L E R E Q U I P P E D M O D E L S O N L Y )
the composition of the
When operating the oven on a regular basis, the steam
gasket from deterioration
generator must be flushed once a day. This procedure will
caused by acidic foods.
prevent lime deposits and scale build-up from forming in the
After allowing the oven to
steam generator. A steam generator flush is automatically
cool, remove pull-out gasket and wash in hot, soapy water.
initiated during the cleaning function on S-Control models.
DO NOT place gasket in the dishwasher.
R E G U L A R D E C A L C I F I C AT I O N
(E L E C T R I C
Always replace the gasket
before cleaning the oven
interior or operating the oven.
B O I L E R E Q U I P P E D M O D E L S O N LY
)
It is VERY important to decalcify the steam generator,
particularly in areas with extremely hard water. In addition
to the daily steam generator flush, this procedure should be
PROBE USAGE AND CLEANING
performed once a month or more frequently depending on
After each use of the CORE TEMP mode, wipe the
probe tip with a clean paper towel to remove food
debris. Follow by wiping the probe with a disposable
alcohol pad. Return the probe to the proper door
bracket position.
usage and water conditions.
PROBE CLEANING PROCEDURES
• Drain Pipe
1.
Remove all food soil from probe between loads
and at the end of each production shift. Wipe
the entire probe, probe cable assembly, and
probe holding bracket with warm detergent
solution and a clean cloth.
• Spray Head
2.
Remove detergent by wiping the probe, cable,
and bracket with clean rinse water and a cloth.
3.
Wipe probe and probe bracket with disposable
alcohol pad or sanitizing solution recommended
for food contact surfaces.
4.
Allow probe and cable to air dry in the probe
holding bracket.
5.
Wipe the probe with a disposable alcohol pad
prior to inserting in a new food product.
M O N T H LY C L E A N I N G
• Water Intake Filter
ALLOW THE OVEN TO COOL BELOW 280°F (140°C)
BEFORE STARTING THE AUTO-CLEAN FUNCTION.
NOTE: The temperature in the display indicates the
air temperature inside the oven compartment and
not the interior walls of the oven. Always make
certain to allow the oven walls to cool to a minimum
of 280°F (140°C) before cleaning.
S E C T I O N 2 – P R E V E N T I V E M A I N T E N A N C E • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 45
PREVENTIVE MAINTENANCE
USE AUTHORIZED COMBITHERM
LIQUID OVEN CLEANER ONLY.
RUBBER GLOVES AND PROTECTIVE
EYE WEAR MUST BE WORN WHEN
USING THE OVEN CLEANER.
Unauthorized cleaning agents may
discolor or harm interior surfaces of the
oven. Read and understand label and material
safety data sheet before using the oven cleaner.
Causes severe burns. Do not get in eyes, on
skin, or on clothing. Do not wear contacts.
Harmful or fatal if swallowed. Do not breathe
mist. Use in well ventilated area. Keep out of reach of children.
Do not use on aluminum. Do not mix with anything but water.
THOROUGHLY RINSE EMPTY CONTAINER WITH WATER AND SAFELY DISCARD .
STEAM RELIEF VALVE
(ON BOILER MODELS)
WATER SUPPLY MUST BE OPEN WHEN
CLEANING PROGRAM IS ACTIVATED.
VERIFY WATER SUPPLY BEFORE STARTING
CLEANING PROGRAM.
STEAM
BYPASS PORT
OVEN LIGHT
FAN
FAN GUARD
COVER PLATE
OVEN DRAIN
S E C T I O N 2 – P R E V E N T I V E M A I N T E N A N C E • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 46
PREVENTIVE MAINTENANCE
A U T O C L E A N ™ A U T O M AT I C C L E A N I N G P R O G R A M
Remove all food scraps and residue from the
o v e n d r a i n . Remove shelves, side racks and pans
and wash separately.
Wi t h t h e o v e n p o w e r
Cleaning in Process
on
PRESS THE CHEF FUNCTION KEY.
Rotate the adjustment knob
until the AutoClean symbol is
highlighted in the display.
After 10 minutes, a buzzer will sound and Display will
show “Open Door/Spray Cleaner”.
Open Door / Spray Cleaner
PRESS THE CHEF FUNCTION KEY.
THE CONTROL WILL ASK FOR
VERIFICATION OF THE FOLLOWING ITEMS
BEFORE THE FUNCTION CAN BE STARTED :
Water turned on?
Wearing safety glasses and rubber gloves, open door,
remove the drain screen and spray Combitherm
liquid oven cleaner diretly into the drain pipe.
Generously spray the interior oven surfaces with an
even coat of Combitherm Liquid Oven Cleaner.
Spray all built-in components.
Verify water is supplied to the oven and
press the up L and down M arrow keys or
rotate the adjustment knob to select “ YES ”.
PRESS THE CHEF FUNCTION KEY.
Start AutoClean?
Insert the Combitherm liquid oven cleaner spray
nozzle directly into the Steam Bypass Port and spray
several times.
ON A WEEKLY BASIS - Loosen the thumb screw(s)
and swing Fan Guard Cover Plate toward the back of
the oven. Spray the back of the Fan Guard Cover
Plate, the oven fan, and the left-hand side of the oven.
When oven door is closed again cleaning cycle
will resume for the remaining 40 minutes.
Cleaning Finished
Press the up L and down M arrow keys or
rotate the adjustment knob to select “ YES ”
for the automatic cleaning function.
PRESS THE CHEF FUNCTION KEY TO
CONFIRM THE SETTING AND START THE
CLEANING PROGRAM.
THE OVEN WILL BEGIN A 50 MINUTE
CLEANING AND RINSE CYCLE.
At the end of the cleaning cycle, the oven will beep
and the display will indicate the end of the cycle.
Press the start / stop key to stop the buzzer and
return the oven to normal operation.
DISPLAY WILL COUNT DOWN INDICATING
TIME REMAINING IN THE CLEANING CYCLE.
L E AV E D O O R S L I G H T LY O P E N A F T E R C L E A N I N G
S E C T I O N 2 – P R E V E N T I V E M A I N T E N A N C E • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 47
PREVENTIVE MAINTENANCE
A U T O C L E A N ™ A U T O M AT I C C L E A N I N G P R O G R A M
(CONTINUED)
FORCED RINSING MODE:
If the cleaning cycle is stopped during cleaning, the
unit will immediately go into a Forced Rinsing mode
for 5 minutes.
If power is lost or the unit is turned off during
cleaning, the unit will go into a Forced Rinsing mode
when power is restored, or unit is turned back on.
Forced Rinsing
Once the Forced Rinsing is complete “Cleaning
Interrupted” will appear on the display.
Cleaning Interrupted
Press the start/stop key to return the oven to normal
operation.
NOTE:
IF THE DOOR IS OPENED
DURING THE CLEANING
PROCESS,
“CLOSE
THE DOOR!”
W I L L A P P E A R I N T H E D I S P L AY.
L E AV E D O O R S L I G H T LY O P E N A F T E R C L E A N I N G
S E C T I O N 2 – P R E V E N T I V E M A I N T E N A N C E • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 48
PREVENTIVE MAINTENANCE
STANDARD CONTROL
DELUXE CONTROL
A U T O M AT I C S T E A M G E N E R AT O R F L U S H
AT T H E S TA R T O F T H E W O R K D AY
Flushing the electric Combitherm steam generator on a daily basis helps to prolong the life of the steam
generator heating elements and helps prevent the necessity of service requirements. The control provides
this feature as an automatic function when the oven ON/OFF power key is pressed to the ON position at the
start of each working day.
PRESS THE ON/OFF POWER KEY TO THE ON POSITION.
DISPLAY MESSAGE INDICATES:
Flush steam generator?
YES
PRESS THE START KEY OR
CHEF FUNCTION KEY to begin the steam generator flush.
The steam generator is automatically drained, flushed, and refilled with water within 5 minutes or less.
Following this time period, the Combitherm is ready for operation.
NO
TO CANCEL THE STEAM GENERATOR FLUSH, ROTATE THE ADJUSTMENT KNOB ONE TURN TO
THE RIGHT UNTIL THE DISPLAY INDICATES “NO”.
PRESS THE START/STOP KEY OR
CHEF FUNCTION KEY to confirm cancellation.
If steam generator flush cancellation is not initiated within 10 seconds of the appearance of the
display message, the flushing function will automatically start. Following cancellation, the
Combitherm is ready for operation. The flushing process must be initiated manually at a later
time during the working day if not conducted at startup.
MANUAL STEAM GENERATOR FLUSH
PERFORM DAILY WHEN THE STEAM GENERATOR FLUSH IS NOT PERFORMED AT THE START OF THE WORKING DAY.
W I T H T H E O V E N AT R O O M T E M P E R AT U R E
1. Press the Power Switch to the OFF position. Rotate the Steam Generator Drain Cap located at the back
of the oven until water begins to flow from the four holes in the cap. In approximately 20 to 60
seconds, a sufficient quantity of water will have drained from the steam generator so that the drain cap
can be completely removed.
2. As the water continues to flow from the generator, it will have a milky or cloudy appearance, which
indicates deposits in the generator are beginning to flush through the system. Let the water continue to
drain until the flow begins to subside.
3. When the flow begins to subside, remove the hand-held hose from the side of the oven and direct a
stream of fresh water directly into the steam generator drain opening located directly behind the Steam
Generator Drain Cap. Repeat this procedure several times until the water begins to run clear.
4. Press the oven Power Switch to the ON position. When the audible signal is heard, press the Steam
Mode Key. A new supply of fresh, cold water will begin to flow through the steam generator. Repeat
this procedure several times until the water runs completely clear.
5. Once the water is completely clear, replace the Steam Generator Drain Cap over the steam generator
drain by turning it clockwise, by hand, until there is a slight resistance.
D O N O T O V E R - T I G H T E N S T E A M G E N E R A T O R D R A I N C A P.
S E C T I O N 2 – P R E V E N T I V E M A I N T E N A N C E • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 49
STANDARD CONTROL
DELUXE CONTROL
PREVENTIVE MAINTENANCE
D E C A L C I F I C AT I O N
ON BOILER EQUIPPED MODELS
using ScaleFree™ or Distilled White Vinegar
STANDARD CONTROL
DELUXE CONTROL
ScaleFree™ Descaling Compound is an acid-based descaler
combined with a proprietary chelating agent that is effective in
dissolving and removing carbonate, lime-scale and iron scale build-up caused by hard water.
ScaleFree efficiently and effectively removes lime-scale build-up from combi ovens.
ScaleFree™ is a non-hazardous, Biodegradable Citrus Based Powder that when mixed with
water becomes a powerful lime-scale remover.
It is VERY important to decalcify the oven, particularly in areas with extremely hard water.
PERFORM ONCE A MONTH in addition to the daily steam generator flush.
WITH THE OVEN AT ROOM TEMPERATURE
1. Begin
decalcification with the power
key in the OFF position.
2.
Open oven door. Wearing hand
protection, rotate the Steam Generator
Drain Cap 햸 until water begins to flow
from the four holes in the cap. In
approximately 20 to 60 seconds, a
sufficient quantity of water will have
drained from the steam generator so that
the drain cap can be completely removed.
STEAM RELIEF VALVE
STEAM EXIT
PORT
STEAM
BYPASS
PORT
OVEN LIGHT
3. Let
the water continue to drain until the
flow completely subsides. Replace the
Steam Generator Drain Cap 햸 by
turning it clockwise until there is a
slight resistance. Close oven door.
4.
5.
FAN
FAN GUARD
COVER PLATE
STEAM
GENERATOR
DRAIN CAP
Using the batch mix instructions on the
label, mix up 1 gallon of ScaleFree™
solution at a time or one gallon of
distilled white vinegar for counter top
models and 3 gallons of distilled white
vinegar for floor standing models. Using
a funnel inserted
into the Steam Relief Valve 햲, slowly pour
solution in to the Steam Generator until full.
OVEN DRAIN
Remove funnel from Steam Relief Valve 햲.
PRESS THE ON/OFF POWER KEY
TO THE ON POSITION.
The unit will add water if needed.
PRESS THE STEAM PROGRAM KEY
The unit will begin to pre-heat.
DO NOT PRESS START.
DURING DECALCIFICATION THE WATER FLOWING
FROM THE DRAIN CAP IS EXTREMELY HOT! USE
HAND PROTECTION WHEN TOUCHING THE STEAM
G E N E R AT O R D R A I N C A P. D O N O T T O U C H T H E
WATER FLOWING OUT OF THE STEAM GENERATOR
DRAIN CAP OR STEAM GENERATOR DRAIN.
(Continued on next page)
S E C T I O N 2 – P R E V E N T I V E M A I N T E N A N C E • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 50
PREVENTIVE MAINTENANCE
ALLOW THE UNIT TO PREHEAT FOR 30 MINUTES.
After a period of 30 minutes —
PRESS THE ON/OFF POWER KEY TO THE OFF POSITION.
STANDARD CONTROL
DELUXE CONTROL
6. Open
the oven door. USING HAND PROTECTION, rotate the Steam Generator Drain Cap 햸 until
water begins to flow from the four holes in the cap. In approximately 20 to 60 seconds, a sufficient
quantity of water will have drained from the steam generator so that the drain cap can be completely
removed. Let the water continue to drain until the flow completely subsides.
7.
Loosen the thumb screw(s) and swing Fan Guard Cover Plate 햷 toward the back of the oven. Using
the hand-held hose, direct a stream of water directly into the Steam Generator Drain 햸 and Steam
Exit Port 햳 several times. Close the swing-out Cover Plate 햷. Lock the cover into place and tighten
thumb screw(s). Close the oven door.
PRESS THE ON/OFF POWER KEY TO THE ON POSITION.
A new supply of fresh water will begin to flush the steam generator.
ALLOW THE WATER TO RUN FOR 2 MINUTES
to continue to flush out all remaining solution.
PRESS THE ON/OFF POWER KEY TO THE OFF POSITION.
8.
Open oven door. USING HAND PROTECTION, replace the Steam Generator Drain Cap 햸 by
turning it clockwise until there is a slight resistance. Close oven door.
PRESS THE ON/OFF POWER KEY TO THE ON POSITION.
The unit will start to fill.
PRESS THE STEAM MODE KEY AND THEN PRESS THE START KEY.
ALLOW UNIT TO RUN FOR 20 MINUTES IN THE STEAM MODE.
PRESS THE ON/OFF POWER KEY TO THE OFF POSITION.
9.
Open the oven door. USING HAND PROTECTION, rotate the Steam Generator Drain Cap 햸 until
water begins to flow from the four holes in the cap. In approximately 20 to 60 seconds, a sufficient
quantity of water will have drained from the steam generator so that the drain cap can be completely
removed. Let the water continue to drain until the flow completely subsides. Replace the Steam
Generator Drain Cap 햸 by turning it clockwise until there is a slight resistance.
At the end of the production day, leave the door slightly ajar.
THE UNIT IS NOW READY TO BE USED.
DO NOT COOK IN ANY PROGRAM MODE WITH
ScaleFree ™ OR VINEGAR IN THE STEAM GENERATOR SYSTEM.
S E C T I O N 2 – P R E V E N T I V E M A I N T E N A N C E • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 51
SERVICE MODE AND ERROR CODES
Service Mode Instructions ..............................................................
53
Error Codes..................................................................................
54
Emergency Operation ...................................................................
58
Return to Main Table of Contents ..................................................
3
SECTION 3 – SERVICE MODE
AND
ERROR CODES • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 52
SERVICE MODE AND ERROR CODES
SERVICE MODE INSTRUCTIONS
The service mode is accessible on units with Standard or Deluxe controls only.
TO ACCESS THE SERVICE MODE
PRESS THE ON/OFF POWER KEY TO THE ON POSITION.
PRESS THE COOK TEMP, TIME AND CORE TEMP KEYS SIMULTANEOUSLY.
The service mode will appear in the display.
or
If the unit does not have a core temperature key, an additional black button is located on the back
of the display board. Remove the left-hand side of the unit or the front control panel to access it.
TO NAVIGATE IN THE SERVICE MODE
R-Number Menu
The service mode has three menus and will open in the R-Number Menu. This menu is read-only
and displays the current temperature (in Celsius), the status of all other sensors and switches, and
the most recent errors and their time of occurrence. Rotate the adjustment knob to view the
status values.
To view the last 10 errors that have occurred:
• Rotate the adjustment knob until the parameter R38 shows in the display.
• Press the up L arrow to display the last 10 errors.
• Press the Chef Function
it occurred.
key to toggle between the error description and the date and time
• Press the down M arrow to return to the parameter R38.
• Rotate the adjustment knob to scroll to another parameter.
C-Number Menu
The second menu, the C-Number Menu, is where all sensor values are set. These values are
changeable, but should only be changed under the direction of an Alto-Shaam factory representative.
Unauthorized changes can cause damage. Rotate the adjustment knob to view these values.
D-Number Menu
The third menu, the D-Number Menu, is the diagnostic menu. Here all components can be
activated for 10 seconds at a time to aid in troubleshooting the oven. To test a component:
• Rotate the adjustment knob until the desired parameter (D07 Fan [0], D12 Oven Lamp [0], etc.)
shows in the display.
• Press the up L arrow to highlight the value [0].
• Rotate the adjustment knob to change [0] to [1]. The component will activate for 10 seconds
and then the display will return to [0].
• Press the down M arrow to return to the parameter without the value highlighted.
• Rotate the adjustment knob to scroll to another parameter.
SECTION 3 – SERVICE MODE
AND
ERROR CODES • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 53
SERVICE MODE AND ERROR CODES
TO EXIT THE SERVICE MODE
PRESS THE START KEY TO EXIT FROM THE SERVICE MODE TO THE NORMAL TIME DISPLAY.
MOST COMMONLY USED PARAMETERS
R-Numbers
C-Numbers
D-Numbers
R01 CTC-1 Multi-Point Product Probe
C01 Nom Standby Temp
D01 Delete Errors
R02 CTC-2 Multi-Point Product Probe
C02 Nom Cond Temp
D02 Key Lock
R03 CTC-3 Multi-Point Product Probe
C03 Fan on Cycle
D03 Delete All Programs
R04 CTC-4 Multi-Point Product Probe
C04 Fan off Cycle
D04 Self Test BM (Display Board)
R05 Oven Temp Sensor (N-6)
C05 Cont Steam
D06 Red Fan Speed
R06 Bypass Probe (B-5)
C06 Init
D07 Fan
R07 Condensate Probe (B-3)
C07 Humidity S
D08 Steam Gen 1
R08 Steam Generator (B-4)
C08 Humidity SS
D09 Convection 1
R09 STB Probe (N-8 Immersion Safety Probe)
C09 Humidity Quick
D10 Steam Gen 2
R10 PT-100 Single-Point Product Probe
C10 Humidity Reg
D11 Convection 2
R13 Electronic Temp (Control Temperature)
C11 Humidity Reg g
D12 Oven Lamp
R20 Lower Level-Water Level Probe *
C12 Bitfield 1
D13 Cond Cooling
R21 Upper Level-Water Level Probe *
C13 Bitfield 2
D14 Steam Gen Fill
R23 Door Switch *
C19 PIN
D28 Venting Motor
R29 Software BM (Display Board)
C23 Time Browning
D30 Smoking Element
R30 Software SM (Relay Board)
C24 Door Venting
D31 Solenoid Valve
R31 Software KM (HACCP Board)
R38 Errors (see R-Number instructions)
* For these parameters, [0] = Not Satisfied, [1] = Satisfied.
TO REBOOT THE CONTROL
Rebooting the control can sometimes fix an error code or a control that is frozen or confused:
PRESS AND HOLD THE ON/OFF POWER KEY FOR FIVE SECONDS.
The display will flash and show ST5000 for 20 seconds, followed by “Please Wait”, and then will
return to the time and date.
PRESS THE ON/OFF POWER KEY MOMENTARILY.
The unit will turn on and can be operated normally.
SECTION 3 – SERVICE MODE
AND
ERROR CODES • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 54
SERVICE MODE AND ERROR CODES
ERROR CODES
When the oven malfunctions, an error code will appear in the display.
PRESS THE START KEY TO ACKNOWLEDGE THE ERROR.
The keys that begin to flash represent operational modes that are still usable. Refer to Emergency
Operation.
When the oven fault is corrected, the Combitherm will return to normal Operation.
ERROR CODES AND REASONS
Error
Code
E01
Display Shows
Low Water
When does the error occur?
Possible reason
ES units only:
• Activated if running in any mode and the
water level drops below the low level
sensor.
• Water supply is shut off.
• Activated if in Standby mode and the water
level drops below the low level sensor for
3 minutes.
• Drain pump is not sealing.
• Low water pressure.
• Steam generator drain cap is off or loose.
• Faulty or scaled water level probe.
• Faulty or plugged solenoid valve assembly.
• Wiring or connection issue.
E02
Control Temp High
Activated if the temperature of the electrical
control is higher than 176°F (80°C) for 20
seconds.
• Cooling fan not operating.
• Unit is next to a heat producing source
(there is less than 20" clearance for the
control side).
• Exhaust hood is not operating (if applicable).
E03
Fan Malfunction
Activated if the motor protection switch is
tripped.
• Motor rotation is backwards.
• Incorrect power to the unit.
• Connection problem at X-7 plug on the relay
board pins 3-4.
E04
Aux Fan Fault
Auxiliary fan malfunction.
E11
Excess Oven Temp
Activated if the oven cavity temperature is
higher than 572°F (300°C) for 25 seconds.
• Control setup programming error.
• Contact factory.
• Connection issue with oven temperature
sensor.
• Convection element contactor is stuck.
• Faulty oven temperature sensor.
E13
Excess Steam Gen Temp
ES units only:
Activated if the temperature of the steam
generator probe (B-4) is higher than 248°F
(120°C) for 26 seconds.
• Problem with water level probe.
• Scale build-up inside steam generator.
• Steam element contactor is stuck.
• Connection issue with B-4 probe.
• Faulty B-4 probe.
SECTION 3 – SERVICE MODE
AND
ERROR CODES • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 55
SERVICE MODE AND ERROR CODES
ERROR CODES AND REASONS (continued)
Error
Code
E15
Display Shows
Excess Condensate Temp
When does the error occur?
Activated if the temperature of the
condensate probe (B-3) is higher than 212°F
(100°C) for 26 seconds.
Possible reason
• Water supply is shut off.
• Faulty or plugged solenoid valve (Y-2).
• Connection issue at B-3 probe.
• Faulty B-3 probe.
E21
E22
Oven Probe Fault
Core Temp Probe Fault
Activated if oven temperature probe (N-6) is
interrupted.
• Connection issue at N-6 probe.
Activated if cooking in Core Temp mode and
the CTC sensor measures an excessive
temperature.
• CTC sensor is damaged.
• Faulty N-6 probe.
• 4-point CTC sensor is activated, but 1-point
CTC sensor is installed.
• Cable connection of CTC sensor is damaged.
• Hardware problem on control unit (SM).
E23
E24
E25
E26
E27
Steam Gen Probe Fault
ES units only:
Activated if the steam generator probe (B-4)
is interrupted.
• Connection issue at B-4 probe.
Activated if the bypass probe (B-5) is
interrupted.
• Connection issue at B-5 probe.
Activated if the condensate probe (B-3) is
interrupted.
• Connection issue at B-3 probe.
Steam Gen Safety Probe
Fault
Activated if the steam generator safety probe
(N-8) is interrupted.
• Connection issue at N-8 probe.
Excess Steam Gen Safety
Temp
ES units only:
Activated if the steam generator safety probe
(N-8) measures a temperature in excess of
266°F (130°C).
• Problem with water level probe.
Bypass Probe Fault
Condensate Probe Fault
• Faulty B-4 probe.
• Faulty B-5 probe.
• Faulty B-3 probe.
• Faulty N-8 probe.
• Scale build-up inside steam generator.
• Steam element contactor is stuck.
• Connection issue with N-8 probe.
• Faulty N-8 probe.
E29
Probe Short to Frame
SECTION 3 – SERVICE MODE
Activated if one or more of the temperature
sensors were connected to GND for 5
seconds.
AND
• Connection issue at any of the temperature
sensors.
• Temperature sensor shorted to
ground/faulty.
ERROR CODES • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 56
SERVICE MODE AND ERROR CODES
ERROR CODES AND REASONS (continued)
Error
Code
E34
Display Shows
DE (Drain) Pump Failure
When does the error occur?
Possible reason
Activated if water level did not drop below
• Problem with water level probe.
the low level sensor in the generator during a
• Scale build-up inside steam generator.
steam generator flush.
• Scale plugging drain pump.
• Faulty drain pump.
E35
Venting Error
Activated when vent switch reads open (vent
closed) when it should be closed (vent open),
or when it reads closed (vent open) when it
should be open (vent closed).
• Alignment issue between motor cam and
micro switch.
• Connection issue at micro switch.
• Connection issue at control.
• Faulty vent switch.
• Faulty vent motor.
E36
Steam Temp High
Activated when oven temperature probe (N-6) • Water supply is shut off while unit is running
measures a temperature in excess of 395°F
in Steam or Combi mode.
(202°C) when running in Steam or Combi
• Plugged or faulty Y-1 solenoid.
mode.
• Obstruction between Y-01 solenoid and
water inlet.
E80
ID Error
Control is unable to detect whether unit is
gas or electric.
E81
Program Memory Error
• Connection issue at X-3 personality jumper.
• Faulty control.
Temperature value or time value of a program • Program was generated in °C and control
step is not allowed.
has been switched to °F.
• Program was generated in °F and control
has been switched to °C.
E82
WP Error
Temperature value or time value of current
cooking algorithm is out of allowed array.
• Delete program and reinstall.
E83
Algo Error
Cooking algorithm sent by operating module
(BM) is unknown to control unit (SM).
• Software versions of control unit and
operating module are incompatible.
• Software error in operating module.
E96
Connection Error
No or bad communication between control
unit (SM) and operating module (BM).
• Connection issue at ribbon cable on display
or relay board.
• Faulty ribbon cable.
• Software versions of control unit and
operating module are incompatible.
SECTION 3 – SERVICE MODE
AND
ERROR CODES • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 57
SERVICE MODE AND ERROR CODES
E M E R G E N C Y O P E R AT I O N
In the event of an error code, the Combitherm may be operated on a limited basis. Error conditions under
which continued operation can be conducted are indicated by “Yes” in the chart shown below.
When the oven malfunctions, an error code will appear in the display.
PRESS THE START KEY TO ACKNOWLEDGE THE ERROR.
The keys that begin to flash represent operational modes that are still usable.
SELECT AND PRESS ONE OF THE COOKING MODES INDICATED.
The oven control will only respond to the mode keys that are flashing.
SET THE OVEN CONTROLS AS IF OPERATING UNDER NORMAL CIRCUMSTANCES.
Depending on the error code involved, oven function, such as temperature range, may be limited.
PRESS THE START KEY TO BEGIN THE COOKING PROCESS.
PRESS THE START KEY WHEN THE TIMER EXPIRES.
When the oven fault is corrected, the Combitherm will return to normal Operation.
CONTINUED OPERATION UNDER ERROR CONDITIONS
Error
Code
Display Shows
ES
ESi
Steam
Mode
Combination
Mode
Convection
Mode
Retherm
Mode
E01
Low Water
Yes
N/A
No
No
To 365°F
No
E02
Control Temp High
Yes
Yes
Yes
To 284°F
To 284°F
To 284°F
E03
Fan Malfunction
N/A
N/A
—
—
—
—
E04
Aux Fan Fault
Yes
Yes
Yes
To 284°F
To 284°F
To 284°F
E11
Excess Oven Temp
Yes
Yes
No
No
No
No
E13
Excess Steam Gen Temp
Yes
N/A
No
No
No
No
E15
Excess Condensate Temp
Yes
Yes
No
No
To 356°F
No
E21
Oven Probe Fault
Yes
Yes
212°F only
No
No
No
E22
Core Temp Probe Fault
Yes
Yes
Yes
Yes
Yes
Yes
E23
Steam Gen Probe Fault
Yes
N/A
Yes
Yes
Yes
Yes
E24
Bypass Probe Fault
Yes
Yes
To 210°F
No
Yes
No
E25
Condensate Probe Fault
Yes
Yes
Yes
To 356°F
To 356°F
To 320°F
E26
Steam Gen Safety Probe Fault
Yes
N/A
Yes
Yes
Yes
Yes
E27
Excess Steam Gen Safety Temp
Yes
N/A
No
No
No
No
E29
Probe Short to Frame
Yes
Yes
No
No
No
No
E34
DE (Drain) Pump Failure
Yes
N/A
Yes
Yes
Yes
Yes
E35
Venting Error
Yes
Yes
Yes
Yes
Yes
Yes
E36
Steam Temp High
N/A
Yes
No
No
Yes
No
E80
ID Error
Yes
Yes
Yes
Yes
Yes
Yes
E81
Program Memory Error
Yes
Yes
Yes
Yes
Yes
Yes
E82
WP Error
Yes
Yes
Yes
Yes
Yes
Yes
E83
Algo Error
Yes
Yes
Yes
Yes
Yes
Yes
E96
Connection Error
Yes
Yes
No
No
No
No
SECTION 3 – SERVICE MODE
AND
ERROR CODES • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 58
SERVICE MODE AND ERROR CODES
NOTES
SECTION 3 – SERVICE MODE
AND
ERROR CODES • COMBITHERM ELECTRIC TECHNICAL SERVICE MANUAL • 59
4
TROUBLESHOOTING TREES
ES Units.......................................................................................
K-77 Safety Contactor Does Not Pull-In at Power-Up
(380-415V Units Only) .............................................................
Unit Dead — No Display and No Operation ...............................
Unit Does Not Run When Start Is Pressed ..................................
No Generator Fill .....................................................................
No Steam Pre-Heat ..................................................................
No Steam Production in Steam Mode ........................................
No Heat in Convection Mode ....................................................
No Steam Production in Combination Mode ...............................
No Convection Heat in Combination Mode ................................
Motor Does Not Run When K-51 Motor Contactor Is Energized ...
61
61
62
63
64
65
66
67
68
69
70
Return to Main Table of Contents ..................................................
3
NOTE: Troubleshooting Guides reflect all counter top models. When working on a
20.20 there are additional elements, motors, and contactors. The following
components are wired to operate together on a 20.20:
• K-41 and K-43 Convection Element Contactors
• K-42 and K-44 Convection Element Contactors
• K-51 and K-71 High Speed Motor Contactors
• K-52 and K-72 Low Speed Motor Contactors
S E C T I O N 4 – T R O U B L E S H O O T I N G T R E E S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 60
TROUBLESHOOTING TREES
ES — K-77 Safety Contactor Does Not Pull-In at Power-Up
(380-415V Units Only)
NOTE: 380-145V units will not heat
if K-77 is not pulled in.
Is there coil voltage
across A-1 and A-2 on
K-77?
No
1. Determine which leg is missing and
correct.
Yes
Replace faulty contactor and test.
-A-1 is L-1 supplied from the 131-2
terminal block. The 131-2 terminal
block is fed from X-1 pin 3 on the
relay board.
-A-2 is L-2 supplied from the
K-41-A-2 contact. Power is jumped
from K-42-A-2 which is supplied from
the N-7 high limit.
2. Reset if tripped and test.
S E C T I O N 4 – T R O U B L E S H O O T I N G T R E E S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 61
TROUBLESHOOTING TREES
ES — Unit Dead — No Display and No Operation
Is power connected to the
unit?
Yes
No
Is there correct voltage at
the power source (outlet)?
Install power to unit/plug
in.
Yes
No
Check breaker, reset if
necessary.
Is there correct voltage at
the main terminal block
(L-1/2/3)?
Replace/Repair faulty
cord/plug/wiring.
Repair wiring issue between block
and fuses.
No
Yes
Is there voltage at
terminals 62/64/66 at the
F-10 fuses?
No
Yes
Is there voltage across
terminals 34-36 at the
F-1 and F-2 fuse block?
No
Repair wiring issue
between fuses and block.
Yes
Is there voltage across
terminals 33-35 at the
F-1 and F-2 fuse block?
Test F-1/2 for blown
fuse(s). Replace if
necessary.
No
Yes
Repair wiring issue between
fuses and terminal blocks.
Is there voltage across
terminals 310-311 at the
power supply?
No
Yes
Is there 12 VDC across
terminals 312-313 at the
power supply?
No
Yes
Replace faulty power
supply.
Is there 12 VDC across pins
1-3 at the X-3 plug on the
relay board?
Correct wiring issue.
Correct/Replace
as needed.
No
Replace faulty board package.
No
Yes
Is the ribbon cable secured
at both the relay and display
board?
Yes
S E C T I O N 4 – T R O U B L E S H O O T I N G T R E E S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 62
TROUBLESHOOTING TREES
ES — Unit Does Not Run When Start Is Pressed
Does the cycle light
appear in the display?
Yes
No
Check start button for free
movement, ensure no other
control buttons are stuck.
Is the door switch
satisfied?
Close door. If closed
check for faulty switch,
magnet, or wiring.
No
Yes
Is the motor protection
switch in the start
position?
No
Reset and test operation.
Yes
Correct/replace ribbon cable.
No
Reboot control by pressing/holding the power
button. If unsuccessful call Alto-Shaam Technical
Service.
Is the ribbon cable
secured between both
boards?
Yes
S E C T I O N 4 – T R O U B L E S H O O T I N G T R E E S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 63
TROUBLESHOOTING TREES
ES — No Generator Fill
Is the cold water supply
properly installed to the
oven?
Yes
No
Correct water supply
installation to oven.
Is the generator empty?
Empty generator by
means of drain cap in
the oven cavity.
Yes
No
Are the B-1/B-2 water
level probes reading
empty?
No
Check tank for scale,
clean out and test.
Yes
Determine which leg of power is missing at the coil.
Y-1-A-1 is L-1 switched from the relay board.
Y-1-A-2 is L-2 constantly fed from the 130-2
terminal.
Is the Y-1 solenoid being
energized?
No
Yes
Is the Y-1 solenoid
opening?
Replace faulty solenoid
assembly.
No
Yes
Is the generator filling
with water?
Remove solenoid assembly and
clean out filter screen.
No
Yes
Do the B-1/B-2 water
level probes satisfy?
Check for a leak between the
solenoid and the generator or at the
generator drain cap.
The generator should have filled in approximately 1 minute. If it took
considerably less or more time check the tank for scale. If correct, the K-1/2/3
contactors should now be energized to preheat the steam generator water.
No
Yes
S E C T I O N 4 – T R O U B L E S H O O T I N G T R E E S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 64
TROUBLESHOOTING TREES
ES — No Steam Pre-Heat
Is the generator full and
the B-1/B-2 satisfied?
Yes
No
Is the B-4 probe below set
point (88°C/190°F)?
See “No Generator Fill”.
Test for a faulty probe. If
not faulty, pre-heat it.
Yes
No
Are the K-1/2/3 contactors
being energized?
Test for coil voltage at contactors.
No
If K-1/K-2
Yes
K-1-A-1 is L-1 switched from X-1 pin 2 on the relay board.
K-1-A-2 is L-2 constantly supplied from the 130 terminal.
K-2-A-1 is L-1 switched from X-1 pin 6 on the relay board.
K-2-A-2 is L-2 constantly supplied from K-1-A-2.
Are the K-1/2/3 contactors
pulling in?
If K-1/2/3
K-1-A-1 is L-1 switched from X-1 pin 2 on the relay board.
K-1-A-2 is L-2 constantly supplied from the 130 terminal.
K-2-A-1 is L-1 fed from K-1-A-1.
K-2-A-2 is L-2 from K-41-A-2.
K-3-A-1 is L-1 switched from X-1 pin 6 on the relay board.
K-3-A-2 is L-2 constantly supplied from K-1-A-2.
No
Replace faulty contactor(s).
Yes
Is there voltage across the
L-1/2/3 side of K-1/2/3?
Check for wiring issue
between K-1/2/3, L-1/2/3
and main terminal block.
No
Yes
Is there voltage across
T-1/2/3 on K-1/2/3?
Replace faulty contactor(s).
No
Yes
Repair wiring issue.
Is there voltage at the
element loop connections?
No
Yes
Are all element loops
drawing power?
Replace faulty element(s).
No
Yes
After 3-4 minutes of
heating is B-4 satisfied?
Test for faulty probe or scaled tank.
No
Preheat is complete.
Yes
S E C T I O N 4 – T R O U B L E S H O O T I N G T R E E S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 65
TROUBLESHOOTING TREES
ES — No Steam Production in Steam Mode
Does the cycle light come
on when pressed?
See “Unit Does Not Run
When Start Is Pressed”.
Yes
No
Is the door switch reading
closed?
No
1. Close door.
Yes
2. Test for faulty door
switch, magnet, or wiring
issue.
Is the vent closed?
Close vent. Unit will not
produce steam when
vent switch is open.
No
Yes
Test for coil voltage at the contactor.
Does the K-51 fan
contactor energize?
No
K-51-A-1 is L-1 switched from the relay board X-1 pin 4.
K-51-A-2 is L-2 jumped from A-2-K-52 fed from 130 terminal.
Yes
Check for faulty B-5 probe. If unit was in
a steam function it may be satisfied.
Run unit in cool down and test again.
Is the B-5 probe below set
point?
No
Yes
See “No Generator Fill.”
Is the generator full and
the B-1/B-2 satisfied?
No
Yes
Test for coil voltage at contactors.
If K-1/K-2
Are the K-1/2/3
contactor(s) being
energized?
No
K-1-A-1 is L-1 switched from X-1 pin 2 on the relay board.
K-1-A-2 is L-2 constantly supplied from the 130 terminal.
K-2-A-1 is L-1 switched from X-1 pin 6 on the relay board.
K-2-A-2 is L-2 constantly supplied from K-1-A-2.
Yes
Are the K-1/2/3 contactors
pulling in?
If K-1/2/3
K-1-A-1 is L-1 switched from X-1 pin 2 on the relay board.
K-1-A-2 is L-2 constantly supplied from the 130 terminal.
K-2-A-1 is L-1 fed from K-1-A-1.
K-2-A-2 is L-2 from K-41-A-2.
K-3-A-1 is L-1 switched from X-1 pin 6 on the relay board.
K-3-A-2 is L-2 constantly supplied from K-1-A-2.
Replace faulty
contactor(s).
No
Yes
Is there voltage across the
L-1/2/3 side of K-1/2/3?
No
Check for wiring issue between K-1/2/3,
L-1/2/3, and main terminal block.
Yes
Is there voltage across
T-1/2/3 on K-1/2/3?
Replace faulty
contactor(s).
Yes
No
Repair wiring issues.
Is there voltage at all
element loop connections?
No
Yes
Replace faulty element(s).
No
Steam production should begin within 3-5 minutes in the oven at which point K-1/2/3
should begin cycling often off of the B-5 set point.
Are all element loops
drawing power?
Yes
S E C T I O N 4 – T R O U B L E S H O O T I N G T R E E S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 66
TROUBLESHOOTING TREES
ES — No Heat in Convection Mode
Does the cycle light come
on when pressed?
Yes
No
See “Unit Does Not Run
When Start Is Pressed”.
Is the door switch reading
closed?
1. Close door.
Yes
No
2. Test for faulty door
switch, magnet, or
wiring issue.
Is the N-6 Oven Probe
below set point?
Check for a faulty N-6
probe. Replace if
necessary.
Replace faulty
contactor.
Yes
Does the K-51 fan
contactor pull in?
Voltage is
present
No
Check for coil voltage
across K-51.
Determine which leg is missing
and correct.
No
Yes
Voltage is not
present
Does the motor run?
-A-1 is L-1 supplied from X-1
pin 4 on the relay board.
-A-2 is L-2 supplied from A-2
on K-52, which is being fed
from the 130-1 terminal block.
See “Motor Does Not
Run When K-51 Motor
Contactor is Energized”.
No
Yes
Are the K-41/42 contactors
pulling in?
Replace faulty
contactor(s).
Determine which leg is missing and
correct.
-A-1 is L-1 supplied to K-41 from
X-1 pin 1 on the relay board.
-A-1 is L-1 and is supplied to K-42
from X-1 pin 7 on the relay board.
-A-2 is L-2 and is supplied to K-42
from the N-7 High Limit from the
auxiliary contacts on the F-52 MP
switch and then jumped to K-41.
Check for coil voltage
across A-1 and A-2 on
K-41/42.
Voltage is
present
Voltage is not
present
Check for loss of power from
K-1/2/3 to K-41/42 which is
being fed from main terminal
block.
No
Yes
Is there voltage at T-1/2/3
side of the K-41/42
contactors?
No
Yes
Is there voltage at L-1/2/3
of the K-41/42 contactors?
2. Reset high limit if tripped and test.
No
3. Replace MP switch if faulty.
Yes
Replace faulty
contactor(s).
Is there voltage at the
convection elements?
Repair wiring
issue.
Ohm out and replace
faulty elements.
No
No
The oven should begin producing heat in the cavity and cycle K-41/42 off of the
N-6 probe.
Yes
Are the convection
elements drawing power
on all legs?
Yes
S E C T I O N 4 – T R O U B L E S H O O T I N G T R E E S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 67
TROUBLESHOOTING TREES
ES — No Steam Production in Combination Mode
Does the cycle light come
on when pressed?
See “Unit Does Not Run
When Start Is Pressed”.
No
Yes
Is the door switch reading
closed?
1. Close door.
2. Test for faulty door
switch, magnet, or wiring
issue.
Yes
No
1. Check for a faulty B-5 probe.
2. If unit was in a steam function it
may be satisfied. Run unit in cool down
and test.
Is the B-5 probe below set
point?
Yes
See “No Generator Fill”.
Is the generator full and
the B-1/B-2 satisfied?
No
Yes
Test for coil voltage at contactors.
Are the K-1/2/3
contactor(s) being
energized?
If K-1/K-2
No
K-1-A-1 is L-1 switched from X-1 pin 2 on the
relay board.
K-1-A-2 is L-2 constantly supplied from the
130 terminal.
K-2-A-1 is L-1 switched from X-1 pin 6 on the
relay board.
K-2-A-2 is L-2 constantly supplied from K-1-A-2.
Yes
Replace faulty
contactor(s).
Are the K-1/2/3 contactors
pulling in?
No
If K-1/2/3
Yes
K-1-A-1 is L-1 switched from X-1 pin 2 on the
relay board.
K-1-A-2 is L-2 constantly supplied from the
130 terminal.
K-2-A-1 is L-1 fed from K-1-A-1.
K-2-A-2 is L-2 from K-41-A-2.
K-3-A-1 is L-1 switched from X-1 pin 6 on the
relay board.
K-3-A-2 is L-2 constantly supplied from K-1-A-2.
Check for wiring issue between K-1/2/3,
L-1/2/3, and main terminal block.
Is there voltage across the
L-1/2/3 side of K-1/2/3?
No
Yes
Replace faulty
contactor(s).
Is there voltage across
T-1/2/3 on K-1/2/3?
No
Yes
Repair wiring issue.
No
Is there voltage at all
element loop connections?
Yes
Replace faulty elements.
No
Steam production begins and within 3-5 minutes when the B-5 probe hits set point (95°C) the K-1/2/3 will
drop out and K-41/42 convection heat should come on. The control will cycle K-41/42 off and K-1/2/3 back
on if the B-5 drops below set point.
Are all element loops
drawing power?
Yes
S E C T I O N 4 – T R O U B L E S H O O T I N G T R E E S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 68
TROUBLESHOOTING TREES
ES — No Convection Heat in Combination Mode
Does the cycle light come
on when pressed?
See “Unit Does Not Run
When Start Is Pressed”.
Yes
No
Is the door switch reading
closed?
1. Close door.
Yes
No
2. Test for faulty door switch,
magnet, or wiring issue.
Is the B-5 probe above set
point?
No
B-5 steam probe must be satisfied first before
bringing on convection heat. If no steam production
see “No Steam Production in Combination Mode.”
Yes
Check for a faulty N-6 probe.
Replace if neccessary.
Replace faulty
contactor.
Determine which leg is missing
and correct.
-A-1 is L-1 supplied from X-1 pin 4
on the relay board.
-A-2 is L-2 supplied from A-2 on
K-52, which is being fed from the
130-1 terminal block.
Replace faulty
contactor.
1. Determine which leg is missing and
correct.
-A-1 is L-1 is supplied to K-41 from X-1
pin 1 on the relay board.
-A-1 is L-1 and is supplied to K-42 from
S-1 pin 7 on the relay board.
-A-2 is L-2 and is supplied to K-42 from
the N-7 high limit and then jumped to
K-41.
Is the N-6 Oven Probe
below set point?
No
Yes
Voltage is present
Check for coil voltage
across K-51.
Does the K-51 fan
contactor pull in?
No
Voltage is not
present
Yes
See “Motor Does Not Run
When K-51 Motor Contactor Is
Energized”.
Does the motor run?
No
Yes
Voltage is present
Check for coil voltage
across A-1 and A-2 on
K-41/42.
Are the K-41/42 contactors
pulling in?
No
Yes
Voltage is not
present
Is there voltage at T-1/2/3
side of the K-41/42
contactors?
Yes
No
Check for loss of power from
K-1/2/3 which is being fed
from main power terminal
block.
Is there voltage at L-1/2/3
of the K-41/42 contactors?
No
Replace faulty
contactor(s).
2. Reset high limit if tripped and test.
Repair wiring issue.
Yes
Is there voltage at the
convection elements?
No
Yes
NOTE: If at any time the
B-5 bypass probe falls
below set point, the unit
will drop out of the
convection mode and begin
steam production regardless
of the N-6 temperature.
Steam always takes priority
over convection.
Ohm and replace faulty
elements.
No
The oven should begin producing heat in the cavity and cycle
K-41/42 off of the N-6 probe.
Are the convection
elements drawing power
on all legs?
Yes
S E C T I O N 4 – T R O U B L E S H O O T I N G T R E E S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 69
TROUBLESHOOTING TREES
ES — Motor Does Not Run When K-51 Motor Contactor Is
Energized
Is there voltage across
terminals 62/64/66 on the
bottom side of F-10
L-1/2/3 fuses?
Check for wiring issue between main
power terminal block and fuses.
Yes
No
Is there voltage across
terminals 63/65/67 on top
side of F-10 L-1/2/3 fuses?
No
Replace blown fuse(s) and test.
Yes
Repair wiring issue between fuses and motor
protection switch.
No
Is there voltage across
terminals 2/4/6 at F-52 MP
switch?
Yes
1. Reset tripped switch (start button in).
2. Test again. If still no voltage replace faulty
MP switch.
No
Is there voltage at terminals
1/3/5 out of MP switch?
Yes
Repair wiring issue between F-51 and K-52.
No
Is there voltage across
L-1/2/3 on K-52 contactor?
Yes
Repair wiring issue between K-51 and K-52.
No
Is there voltage across
L-1/2/3 on K-51 contactor?
Yes
Replace faulty K-51 contactor and test.
No
Ensure wiring into and out of motor harness plug is correct and tight. If still no motor operation, replace
faulty motor and test.
Is there voltage out of K-51
at T-1/2/3?
Yes
S E C T I O N 4 – T R O U B L E S H O O T I N G T R E E S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 70
5
C O M B I T H E R M PA R T S
ES Rear Service Parts ...................................................................
72
Outer Panel Assembly ...................................................................
73
Plumbing Assembly .......................................................................
74
Condensation Tank .......................................................................
76
Sprayer Holder Assembly ..............................................................
77
Oven Light Assembly ....................................................................
77
Deluxe Control .............................................................................
78
Combitherm Motor .......................................................................
79
Directional Panel...........................................................................
80
Steam Generator ..........................................................................
81
Recessed Door..............................................................................
82
Return to Main Table of Contents ..................................................
3
S E C T I O N 5 – C O M B I T H E R M PA R T S • 20•20ES
MARINE
C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 71
PA R T S I N F O R M AT I O N
E S R E A R S E R V I C E PA R T S
4
1
2
3
5
6
7
8
10
9
11
Item
Part
Description
1
CM-22794
Clamp
2
HO-27891
Hose, 1-7/8" Dia.
3
HO-2957
Hose
4
1000719
Pump Bracket
5
PB-26512
Plumbing Probe
6
HO-27892
Hose, 7/8" Dia.
7
CM-27190
Tube Clamp
8
DA-24973
Drain Pump
9
EB-25106
Elbow Drain
10
EB-22221
Elbow
11
HO-2957
Hose
S E C T I O N 5 – C O M B I T H E R M P A R T S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 72
PA R T S I N F O R M AT I O N
O U T E R PA N E L A S S E M B LY
4
A
3
2
DETAIL A
1
5
6
7
8
Item
MARINE
Description
Qty.
1006601
Directional Panel Space
2
2
BU-28391
Bushing, Socket, Membrane
1
3
1007000
Outer Cover
1
4
BU-22204
Bushing, Socket, Membrane
1
5
5005769
Motor Cover Assembly
1
6
5005590
Plumbing Assembly
1
7
GS-26641
Gasket, Door, 20.20es
1
Door Assembly, 20.20es
1
8
S E C T I O N 5 – C O M B I T H E R M PA R T S • 20•20ES
Part
1
C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 73
PA R T S I N F O R M AT I O N
P L U M B I N G A S S E M B LY
43
44
35
5
3
45
57
52
60
3
25
10
14
47
50
23
26
33
32
35
DETAIL E
THREE DIRECTIONAL PANEL
SPACERS ARE PLACED
UNDER BT-27946, MANIFOLD
MOUNT.
E
17
53
6
28
7
28
23
32
30
23
ATTACHES TO
STEAM
GENERATOR
20
38
ATTACHES TO
SPRAYER HOLDER
12
ATTACHES TO
CONDENSOR
F
S E C T I O N 5 – C O M B I T H E R M PA R T S • 20•20ES
7
MARINE
C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 74
PA R T S I N F O R M AT I O N
Item
Qty.
Item
1
1000719
Part
Pump Bracket
Description
1
29
FT-28125
Pipe Plug
1
2
1005540
Condensor Tank Spacer
8
30
FT-28660
Return Bend
1
3
1006601
Directional Panel Spacer
4
31
HO-22116
90 Degree, Fitting Elbow
1
4
5004946
Steam Generator Assembly
1
32
HO-27301
Hose, Hand Shower Connection
1
5
5006237
Double Vent Holder Assembly
1
33
NP-27538
Valve Holder Assembly
2
6
5008586
Outer Casing Assembly
1
34
NU-22291
Nut, Hex
4
7
5008659
Condensor Tank Assembly
1
35
NU-22759
Nut, Hex
2
8
BT-27946
Manifold Mount
1
36
PB-26960
Sprayer Holder
1
9
HO-27892
Bulk Hose, 7/8" Hi Temp
1
37
PB-27945
Plumbing, Manifold w/Tubing
4
10
HO-22255
Bulk Hose, 1/2" Water
1
38
PB-27951
Manifold
1
11
HO-2957
Bulk Hose, Silicon
1
39
SA-26890
Seal, Pressure Valve
1
12
HO-27891
Bulk Hose, Hi Temp
1
40
SA-28149
O-Ring
2
13
HO-27891
Bulk Hose, Hi Temp
1
41
SC-22284
Screw, Hex Head
2
14
HO-27892
Bulk Hose, 7/8" Hi Temp
1
42
SC-22766
Screw, Pan Head Phillips
2
15
HO-27893
Bulk Hose, 1/2" Hi Temp
1
43
SC-22779
Screw, Pan Head
8
16
HO-2957
Bulk Hose, Silicon
1
44
SC-26060
Screw, Hex Head
3
17
HO-27891
Bulk Hose, Hi Temp
1
45
SC-28142
Screw
4
18
HO-22255
Bulk Hose, 1/2" Water
1
46
TE-27204
Connector
1
19
CL-22234
Clamp, Worm Gear
10
47
VA-26838
Pressure Valve
1
20
CM-22794
Clamp, Gear
4
48
VA-34045
Valve, Double Port
1
21
CM-28145
Clamp, Hose
8
49
VA-34300
Valve, Single Port
1
22
CP-22758
Steam Generator Outlet
1
50
WS-22294
Washer, Flat
4
23
DA-24973
Steam Generator Pump
1
51
WS-22295
Washer, Flat
13
24
EB-22221
Nickel Plated Elbow
1
52
WS-22297
Washer, Flat
6
25
EB-25106
Steam Generator Drain Elbow
1
53
WS-22300
Washer, Split Lock
4
26
EB-27207
Washer, Drain Support
2
54
WS-22301
Washer, Split Lock
13
27
FT-27406
Brass Reducer Fitting
4
55
WS-22302
Washer, Split Lock
6
28
FT-28124
Clamp, Hose
2
56
WS-22751
Silicone Seal
1
S E C T I O N 5 – C O M B I T H E R M PA R T S • 20•20ES
MARINE
Part
Description
C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 75
Qty.
PA R T S I N F O R M AT I O N
E S C O N D E N S AT I O N TA N K
5
4
6
3
1
4
2
3
9
7
10
8
Item
Part
Description
Qty.
1
CP-22758
Outlet, Steam Generator, 303-304 S/S
1
2
WS-22752
Silicone, Seal, 32 mm FDA, 500F Temp.
1
3
SA-25061
CT, T-Couple Probe, ML Combi
2
4
PR-33751
CT, ML Combi, Thermocouple, 3050 mm Wire Length, ML Combi
2
5
5000284
Inject, Nozzle Condensor Weld
1
6
SA-22209
O-Ring, 8 x 3 mm V75 Vitan 75 Durometer
1
7
PB-26512
Measure Probe
1
8
WS-22207
CT, Seal, 3/4 x 2, Flat Vulcan Fiber
1
9
5004529
Condensor Tank Welding
1
10
SA-22212
CT, O-Ring, Red, Silicone 70 Dur, 225C, 59.6 x 5.33 mm
1
S E C T I O N 5 – C O M B I T H E R M P A R T S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 74
PA R T S I N F O R M AT I O N
S P R AY E R H O L D E R A S S E M B LY
Item
1
2
Part
Description
Qty.
1
PB-26960
Hand Shower Holder
1
2
WS-22295
Flat Washer
4
3
WS-22301
Locking Washer
4
4
SC-22766
Philips Screw
4
4
3
OVEN LIGHT
Item
1
2
3
4
Part
Description
Qty.
1
CV-26607
Oven Light Cover
1
2
GL-26608
Oven Light Glass
1
3
GS-26609
Oven Light Gasket
1
4
LP-34206
Light, 15W Bulb
1
5
LP-34161
Light, Snap-In
1
5
S E C T I O N 5 – C O M B I T H E R M P A R T S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 75
PA R T S I N F O R M AT I O N
DELUXE CONTROL
1
2
3
4
5
6
7
11
8
7
9
10
Item
Part
Description
Qty.
1
PE-27215
Panel, Overlay, Deluxe
2
5006868
Control Panel Spot
1
3
BU-25094
Bushing, CT, ML, Brass, Distance
12
4
BA-33991
Board, CT Alto-Shaam Name, MLG's
1
5
NU-25095
Knurled M3 High A2 S/S
12
6
BA-34313
Board, Operation
1
7
5007610
Control Knob Assembly
1
8
CR-33743
Connector
2
9
BA-33742
Board, Program
1
10
BA-33733
Board, LED, Closed System
1
11
CB-34033
Cable, Communication
1
S E C T I O N 5 – C O M B I T H E R M P A R T S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 76
1
PA R T S I N F O R M AT I O N
COMBITHERM MOTOR
Please Verify Correct Voltage Motor
6
Apply anti-seize on the motor
shaft (fully) before and after
installing part #5 (SL-22214).
4
3
1
5
2
7
Electric Motor Assembly
ES/ML Combi's
Item
Part
Description
Qty.
1
WS-22217
1.25 OD Washer
1
2
BU-22213
Bushing, CT, 30D, Motor Shaft
1
3
SD-23939
Spring
1
4
1000716
Motor Baffle
1
5
SL-22214
Motor Sleeve
1
6
5000602
Motor, 440/480V, 380/415 3PH
1
7
MO-22191
Keyway, Motor
1
S E C T I O N 5 – C O M B I T H E R M P A R T S • C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 77
PA R T S I N F O R M AT I O N
D I R E C T I O N A L PA N E L A S S E M B LY
2
3
1
Item
S E C T I O N 5 – C O M B I T H E R M PA R T S • 20•20ES
MARINE
Part
Description
Qty.
1
1007008
Directional Panel, 20.20es
1
2
CL-24089
Holding (Lock Clip)
2
3
WS-24090
Clip, Lock, W/3 Washers
2
C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 80
PA R T S I N F O R M AT I O N
S T E A M G E N E R AT O R A S S E M B LY
12
1
3
4
5
6
12
7
2
11
8
10
9
Item
S E C T I O N 5 – C O M B I T H E R M PA R T S • 20•20ES
MARINE
Part
Description
Qty.
1
PR-3706
CT, Water Lev. Lg 3/4" NPT Fitting, 316 S/S Electr.
1
2
SA-25061
CT, T-Couple Probe
2
3
PR-33724
CT, Thermocouple, 1650 mm Wire Length
1
4
EL-33411
CT, Heater, Immersion, 9 kw, Flanged
2
5
WS-22302
Washer, Lock, M6, DIN 127B
9
6
WS-22297
Washer, Flat, M6 DIN 125
9
7
NU-22291
M6-1.0 x Hex S/S Nut 18-8
9
8
PR-33759
CT, Temperature Sensor
1
9
ST-22258
Insulation Spike
12
10
SA-23932
O-Ring, 14 mm x 2.5 mm Viton
3
11
EL-33412
CT, Heater, ML, Combi Immersion, 6 kw, Flanged
1
12
IN-22265
Insulation, Steam Gen
1
C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 81
PA R T S I N F O R M AT I O N
R E C E S S E D D O O R A S S E M B LY
1
19
27
25
25
24
26
21
19
21
1
5
14
29
11
10
2
.140 3.55
GLASS TO
INNER FLANGE
2
17
12
6
SECTION D-D
SECTION A-A
17
3
12
3
3
16
4
4
4
22
10
27
9
24
6
9
26
11
7
20
28
14
28
18
E
DETAIL E
1
15
30
13
1
3
10
27
15
5
1
23
14
2
18
SECTION B-B
GASKET HIDDEN
20
Item
Qty.
Item
1
5009101
Part
Outer Door Spot Assembly
Description
1
16
SP-27212
Spacer, Window Latch
3
2
5009319
Inner Door Spot Assembly
1
17
SP-27682
Spacer, Inner Glass Latch
3
3
5005799
Inner Door Glass Assembly
1
18
HG-25079
Hinge, Upper Ratchet
1
4
HD-26966
Handle, Door
1
19
HG-25077
Hinge, Top Stop
1
5
SC-22284
Screw, Hex Head
6
20
SC-22282
Screw, Oval Head
1
6
SC-28253
Screw, Pan Head
4
21
SC-25085
Screw, Oval Head
1
7
WS-22295 Washer, Flat
4
22
SC-28430
Screwm Pan Head
2
8
WS-22301 Washer, Split Lock
4
23
BM-27116
Bumper Stop
2
9
SC-22779
Screw, Pan Head
4
24
SP-27657
Spacer, Glass, 20 mm
3
10
PI-26974
Pin, Lower
2
25
SC-25091
Screw, Sloted Set Screw
6
11
RI-27108
Rivet, Sealed
91
26
BM-27146
Bumper Stop/Inner Door
3
12
CL-27854
Inner, Door Latch
2
27
1009295
Hinge Lower Glass Holder
1
13
GS-25619
Gasket, Door
1
28
1008902
Door Seal Support Bracket
1
14
HG-25078
Hinge, Anchor
2
29
1009850
Hinge Upper Glass Holder
1
15
GL-27230
Glass, Outer Door, 20.20es
1
30
TA-25125
Tape, Double Sided
2
S E C T I O N 5 – C O M B I T H E R M PA R T S • 20•20ES
MARINE
Part
Description
C O M B I T H E R M E L E C T R I C T E C H N I C A L S E R V I C E M A N U A L • 82
Qty.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement