Specifications | Carrier 19XRV Air Conditioner User Manual

19XRV
with PIC III Controls
Rockwell PowerFlex 755 VFD Option
Start-Up and Service Instructions
SAFETY CONSIDERATIONS
Centrifugal liquid chillers are designed to provide safe and
reliable service when operated within design specifications. When operating this equipment, use good judgment
and safety precautions to avoid damage to equipment and
property or injury to personnel.
Be sure you understand and follow the procedures and
safety precautions contained in the chiller instructions as
well as those listed in this guide.
DANGER
ONLY QUALIFIED Electrical Personnel familiar with the construction
and operation of this equipment and the hazards involved should install,
adjust, operate, or service this equipment.
READ AND UNDERSTAND this manual and other applicable manuals in
their entirety before proceeding. Failure to observe this precaution could
result in severe bodily injury or loss of life.
DO NOT install modification kits with power applied to the drive. Disconnect and lock out incoming power before attempting such installation or
removal. Failure to observe this precaution could result in severe bodily
injury or loss of life
UNUSED WIRES in conduit must be grounded at both ends to avoid a
possible shock hazard caused by induced voltages. Also, if a drive sharing
a conduit is being serviced or installed; all drives using this conduit should
be disabled to eliminate the possible shock hazard from cross-coupled
motor leads. Failure to observe these precautions could result in bodily
injury.
DO NOT VENT refrigerant relief valves within a building. Outlet from
rupture disc or relief valve must be vented outdoors in accordance with the
latest edition of ANSI/ASHRAE 15 (American National Standards Institute/American Society of Heating, Refrigerating, and Air Conditioning
Engineers). The accumulation of refrigerant in an enclosed space can displace oxygen and cause asphyxiation.
PROVIDE adequate ventilation in accordance with ANSI/ASHRAE 15,
especially for enclosed and low overhead spaces. Inhalation of high concentrations of vapor is harmful and may cause heart irregularities, unconsciousness, or death. Misuse can be fatal. Vapor is heavier than air and
reduces the amount of oxygen available for breathing. Product causes eye
and skin irritation. Decomposition products are hazardous.
DO NOT USE OXYGEN to purge lines or to pressurize a chiller for any
purpose. Oxygen gas reacts violently with oil, grease, and other common
substances.
NEVER EXCEED specified test pressures, VERIFY the allowable test
pressure by checking the instruction literature and the design pressures on
the equipment nameplate.
DO NOT USE air for leak testing. Use only refrigerant or dry nitrogen.
DO NOT VALVE OFF any safety device.
BE SURE that all pressure relief devices are properly installed and functioning before operating any chiller.
THERE IS A RISK OF INJURY OR DEATH by electrocution. High voltage may be present on the motor leads even though the motor is not running. Open the power supply disconnect before touching motor leads or
terminals.
WARNING
DO NOT WELD OR FLAMECUT any refrigerant line or vessel until all
refrigerant (liquid and vapor) has been removed from chiller. Traces of
vapor should be displaced with dry air or nitrogen and the work area
should be well ventilated. Refrigerant in contact with an open flame produces toxic gases.
DO NOT work on high-voltage equipment unless you are a qualified electrician.
DO NOT WORK ON electrical components, including control panels,
switches, VFD, or oil heater until you are sure ALL POWER IS OFF and
no residual voltage can leak from capacitors or solid-state components.
LOCK OPEN AND TAG electrical circuits during servicing. IF WORK IS
INTERRUPTED, confirm that all circuits are deenergized before resuming
work.
AVOID SPILLING liquid refrigerant on skin or getting it into the eyes.
USE SAFETY GOGGLES. Wash any spills from the skin with soap and
water. If liquid refrigerant enters the eyes, IMMEDIATELY FLUSH EYES
with water and consult a physician.
DO NOT ATTEMPT TO REMOVE fittings, covers, etc., while chiller is
under pressure or while chiller is running. Be sure pressure is at 0 psig (0
kPa) before breaking any refrigerant connection.
CAUTION
TO AVOID an electric shock hazard, verify that the voltage on the bus
capacitors has discharged completely before servicing. Check the DC bus
voltage at the Power Terminal Block by measuring between the +DC and DC terminals, between the +DC terminal and the chassis, and between the
-DC terminal and the chassis. The voltage must be zero for all three measurements.
THE USER is responsible to conform with all applicable local, national,
and international codes. Failure to observe this precaution could result in
damage to, or destruction of, the equipment.
THIS DRIVE contains ESD (Electrostatic Discharge) sensitive parts and
assemblies. Static control precautions are required when installing, testing,
servicing or repairing this assembly. Component damage may result if
ESD control procedures are not followed. For static control procedures,
reference Rockwell publication Guarding Against Electrostatic Damage, or
any other applicable ESD protection handbook.
DO NOT alter the setting of any jumper. Failure to observe this precaution
could result in damage to, or destruction of, the equipment.
USE OF power correction capacitors on the output of the drive can result
in erratic operation of the motor, nuisance tripping, and/or permanent damage to the drive. Remove power correction capacitors before proceeding.
Failure to observe this precaution could result in damage to, or destruction
of, the equipment.
MOST CODES require that upstream branch circuit protection be provided to protect input power wiring. If fuses are chosen as the protection
method, refer to the PowerFlex 750 user manual. Failure to observe this
precaution could result in damage to, or destruction of, the equipment.
DO NOT route signal and control wiring with power wiring in the same
conduit. This can cause interference with drive operation. Failure to
observe this precaution could result in damage to, or destruction of, the
equipment.
DISTRIBUTION SYSTEM short circuit capacity shall not exceed the rating of the drive. Failure to observe this precaution could result in damage
to, or destruction of, the equipment.
DO NOT STEP on refrigerant lines. Broken lines can whip about and
release refrigerant, causing personal injury.
DO NOT climb over a chiller. Use platform, catwalk, or staging. Follow
safe practices when using ladders.
USE MECHANICAL EQUIPMENT (crane, hoist, etc.) to lift or move
inspection covers or other heavy components. Even if components are
light, use mechanical equipment when there is a risk of slipping or losing
your balance.
BE AWARE that certain automatic start arrangements CAN ENGAGE
THE VFD, TOWER FAN, OR PUMPS. Open the disconnect ahead of the
VFD, tower fans, or pumps.
USE only repair or replacement parts that meet the code requirements of
the original equipment.
PERIODICALLY INSPECT all valves, fittings, and piping for corrosion,
rust, leaks, or damage.
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53190012-01
Printed in U.S.A.
Form 19XRV-3SS
Pg 1
711 3-11
Replaces: New
Required Publications — The Carrier VFD option
Start-Up and Service Manual must be used with the following
manuals:
• The latest version of the PowerFlex 750-Series AC
Drives manuals
• The latest revision of the Start-Up, Operation, and Maintenance Instructions for the 19XRV with PIC III Controls
CONTENTS
Page
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . 1
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ABBREVIATIONS AND EXPLANATIONS . . . . . . . . . . 2
Required Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Getting Assistance from Rockwell Automation . . . 2
IDENTIFYING DRIVE COMPONENTS. . . . . . . . . . . . 2-5
Opening the VFD Access Door . . . . . . . . . . . . . . . . . . . 3
Drive Assembly Catalog Number . . . . . . . . . . . . . . . . . 3
Components and Physical Data . . . . . . . . . . . . . . . . . . 3
START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Alternate Wire Lugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Verify Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Configure the VFD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Commissioning the Unit. . . . . . . . . . . . . . . . . . . . . . . . . . 6
Check Internal Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-27
Troubleshooting the Drive . . . . . . . . . . . . . . . . . . . . . . . . 8
• ICVC ALERT CODES
• ICVC ALARM CODES
• TEST EQUIPMENT NEEDED TO TROUBLESHOOT
• VERIFYING THAT DC BUS CAPACITORS ARE
DISCHARGED
• HIGH TEMPERATURE ALARMS
• MAIN CONTROL BOARD (MCB) COMPONENTS
Checking Power Modules and Motor Input
with Input Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . 22
 Servicing the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
• REMOVING THE DRIVE
• RIGGING THE ENCLOSURE
• REPLACING THE GATEWAY (A-B20-750-20COMM
OPTION CARD)
• CHILL PLATE FAN AND INTERNAL FAN
REPLACEMENT
Parts Identification and Location . . . . . . . . . . . . . . . . 26
APPENDIX A — WIRING SCHEMATICS . . . . . . . 28-31
APPENDIX B — OPTIONAL BACNET
COMMUNICATIONS WIRING . . . . . . . . . . . . . . . 32-38
Getting Assistance from Rockwell Automation — Contact the local Rockwell Automation sales office
with any questions or problems relating to the products described in this manual. For technical support on drives between
the hours of 7:00 am and 6:00 pm CST, M-F, call 1-262-5128176. For information about after-hours phone support and onsite support call 1-800-800-0522.
Before calling, have the following information available
from the Allen-Bradley data nameplate located inside the enclosure on the right wall. See Fig. 1.
• Allen-Bradley ID or CAT. NO.
• Carrier VFD Code
• Allen-Bradley serial number
Fig. 1 — Allen Bradley Data Nameplate
A19-1830
INTRODUCTION
The Carrier VFD option Start-Up and Service Manual is intended for trained and qualified service personnel, and is to be
used during start up, operation, and maintenance of Rockwell/
Allen-Bradley PF755L drive.
IDENTIFYING DRIVE COMPONENTS
A chiller control schematic and a VFD schematic are included in Appendix A.
WARNING
ABBREVIATIONS AND EXPLANATIONS
Frequently used abbreviations in this manual include:
CCM
DC
DPI
ENET
ICVC
IGBT
I/O
IP
IPWM
MCB
MOV
PE
SIO
STS
711
—
—
—
—
—
—
—
—
—
—
—
—
—
—
DC bus capacitors retain hazardous voltages after input
power has been disconnected. After disconnecting input
power, wait five (5) minutes for the DC bus capacitors to
discharge and then check the voltage with a voltmeter rated
for the DC bus voltage to ensure the DC bus capacitors are
discharged before touching any internal components. Failure to observe this precaution could result in severe bodily
injury or loss of life.
An isolated multimeter will be needed to measure DC bus
voltage and to make resistance checks. The drive’s DC bus
capacitors retain hazardous voltages after input power has
been disconnected.
Chiller Control Module
Direct Current
Drive Peripheral Interface
Ethernet
International Chiller Visual Controller
Insulated Gate Bipolar Transistor
Inputs/Outputs
Internet Protocol
Inverter Pulse Width Modulation
Main Control Board
Metal Oxide Varistor
Protective Earthing Conductor
Sensor Input/Output
Status
2
Opening the VFD Access Door
WARNING
Before removing the drive enclosure, open access door and
verify that the DC bus voltage has dropped to zero by
checking the terminals behind the access door. Failure to
observe this precaution could result in severe bodily injury
or loss of life.
1. Using recommended screwdriver = 6.4 mm (0.25 in.) flat
or T20 star, open access door. See Fig. 2.
2. Check to be sure that the voltage between DC+ and DCand from each DC terminal to the chassis is zero before
proceeding. See Fig. 3.
Drive Assembly Catalog Number — See Fig. 4 for
an example Catalog Number.
Components and Physical Data — The AllenBradley PF755 Frame 6 drive is used for the 230-amp rated application (carrier Part No. 19XRV0230...). See Fig. 5.
The Allen-Bradley PF755 Frame 7 drive is used for the
335-amp and 445-amp rated application (Carrier Part No.
19XVR0335... and 19XVR0445... respectively). See Fig. 6.
See Fig. 7 for the dimensions of Frames 6 and 7.
Fig. 2 — Opening Access Door
A19-1831
1
L1
L2
L3
I
LOCKOUT/TAGOUT
O
2
DC BUS TEST
TERMINALS
LOCATED INSIDE
ACCESS DOOR
DC+ DC–
0V
0V
MULTIMETER
Fig. 3 — Check DC Bus Terminals
A19-1814
A19-1842
21P
21P 1
0248
3 - 3 - 0 - 0 -C
PF755 VFD
Customer
C – Carrier
Voltage Rating
1 – 460 to 480 v, 60 Hz
2 – 380 to 415 v, 50 Hz
3 – 380 to 400 v, 60 Hz
4 – 401 to 439 v, 60 Hz
Meter Package
0 – No Meter Package
1 – Analog Meter Package
Input Reactor
0 – No Input Reactor
1 – 3% Input Line Reactor
PF755 Full Load Amp Rating
(Maximum Continuous Amps)*
0248 – 248
0361 – 361
0477 – 477
Disconnect/Breaker Options
3 – 65 KAIC Capacity Breaker
4 – 100 KAIC Capacity Breaker
Drive Assembly
3 – Unit Mount NEMA 1 Liquid Cooled
* For Carrier applications, maximum continuous amp
ratings are 230, 335, and 445.
Fig. 4 — Drive Assembly Catalog Number Nomenclature
3
LEGEND
NO.
1
2
3
4
5
NAME
Power Terminals
PE Grounding Studs
DC Bus and Brake
Terminals
PE-A and PE-B
DC+ and DC-
A191832
DESCRIPTION
R/L1, S/L2, T/L3, U/T1, V/T2, W/T3
Terminating point to chassis ground
for incoming motor shield
+DC, -DC, BR1, BR2
MOV and CMC Jumper Wires
Bus Voltage Test Points
A19-1833
LEGEND
Fig. 5 — Frame 6 Drive Components
NO.
1
2
3
4
5
NAME
Power Terminals
PE Grounding Studs
DC Bus and Brake
Terminals
PE-A and PE-B
DC+ and DC-
DESCRIPTION
R/L1, S/L2, T/L3, U/T1, V/T2, W/T3
Terminating point to chassis ground
for incoming motor shield
+DC, -DC, BR1, BR2
MOV and CMC Jumper Wires
Bus Voltage Test Points
Fig. 6 — Frame 7 Drive Components
4
CAUTION
If other than refrigerant cooling is used, before connecting
the drive to the incoming power, make sure that the coolant
is circulating and has no leaks.
CAUTION
When working with the Drive Explorer, never use the
Rotate function as the motor will immediately start and
severe compressor damage could result.
Alternate Wire Lugs — In the case where the incoming
power wire size does not fit the standard lug, alternate lugs may
be used. See Table 1. Note that lugs rated for a higher current
than the circuit breaker may be used.
Table 1 — Wire Lugs
CIRCUIT
BREAKER
STANDARD
ABB LUG
STANDARD
LUG CABLE
RANGE
ALTERNATE
ABB LUG
ALTERNATE
LUG CABLE
RANGE
65 KAIC
(Standard)
100 KAIC
(Optional)
K6TJ
(3) 2/0 - 400
MCM
K6TH
(2) 250 - 500
MCM
Verify Installation — Record
the following job
information:
1. Job Name
2. Job Number
3. City
4. State
5. Zip Code
Record the following nameplate information:
1. From the Allen-Bradley nameplate (Fig. 1) located inside
the VFD enclosure:
a. Allen-Bradley ID or CAT NO.
b. Allen-Bradley Serial Number
c. Carrier Part Number
2. From the machine nameplete (Fig. 8) located inside the
VFD enclosure:
a. Chiller Serial Number
b. Chiller Model
c. Motor rated load amps
d. Motor nameplate rpm
e. Motor nameplate kW
f. Motor nameplate voltage
g. IPWM (pulse width modulation) frequency
h. Voltage
3. From the drive module label (Fig. 9) located on the drive
module:
a. Model or Cat. Number
b. Serial Number
4. From the ICVC control panel screen:
a. Carrier Part Number and Revision
b. ICVC Software Number
Rockwell PowerFlex 750 drive start-up must be registered
on the Rockwell website. Rockwell Registration site URL:
http://www.automation.rockwell.com/warp/default.asp
A19-1834
Fig. 7 — Enclosure Dimensions - Frames 6 and 7
START-UP
DANGER
Internal components and circuit boards of the drive are live
when the drive is connected to incoming power. Coming
into contact with this voltage is extremely dangerous and
will result in severe personal injury or death.
The motor terminals U, V, W and the DC-link/brake resistor terminals B+/R+, R- are live when the drive is connected to incoming power, even if the motor is not running.
Do not make any connections when the drive is connected
to the incoming power.
After having disconnected the drive, wait until the indicators on the keypad go out (if no keypad is attached see the
indicator through the keypad base). Wait 5 more minutes
before doing any work on drive connections. Do not even
open the cover before this time has expired..
Before connecting the drive to the incoming power, make
sure that the switchgear enclosure door is closed.
WARNING
The control I/O-terminals are isolated from the mains
potential. However, the relay outputs and other I/O terminals may have a dangerous control voltage present even
when the drive is disconnected from incoming power.
Coming into contact with this voltage could result in severe
personal injury.
5
Configure the VFD — All configurations required by
the VFD are supplied by the ICVC through the VFD Gateway.
Any configuration changes necessary and possible are made on
the ICVC screens. A complete set of configurations is transmitted to the VFD each time the controls are powered up.
The following is from the 19XRV PIC III ICVC screen. Parameters in italics are to be entered or confirmed at start-up. Parameters in bold are to be changed only after consulting with
Carrier service engineering. See Table 2.
a191846
A United Technologies Company
Table 2 — VFD Configurations
MODEL NUMBER
SERIAL NUMBER
PARAMETER
Motor Nameplate Voltage
Compressor 100% Speed
Line Freq=60 Hz? (No=50)
Rated Line Voltage*
Rated Line Amps*
Rated Line Kilowatts *
Motor Rated Load kW*
Motor Rated Load Amps*
Motor Nameplate Amps
Motor Nameplate RPM
Motor Nameplate KW
Inverter PWM Frequency (0 = 4 kHz, 1 =
2 kHz)
Skip Frequency 1 (Hz)
Skip Frequency 2 (Hz)
Skip Frequency 3 (Hz)
Skip Frequency Band Line (Hz)
Voltage % Imbalance
Line Volt Imbalance Time (sec)
Line Current % Imbalance
Line Current Imbal Time (sec)
Motor Current % Imbalance
Motor Current Imbal Time
Increase Ramp Time (sec)
Decrease Ramp Time (sec)
Single Cycle Dropout (DSABLE/ENABLE)
MACHINE NAMEPLATE SUPPLY DATA
VOLTS/PHASE/HERTZ
LOCKED ROTOR AMPS
OVERLOAD TRIP AMPS
MAX FUSE/CIRCUIT BREAKER SIZE
MIN SUPPLY CIRCUIT AMPACITY
MACHINE ELECTRICAL DATA
MOTOR NAMEPLATE VOLTAGE
COMPRESSOR 100% SPEED
RATED LINE VOLTAGE
RATED LINE AMPS
RATED LINE KILOWATTS
MOTOR RATED LOAD KW
MOTOR RATED LOAD AMPS
MOTOR NAMEPLATE AMPS
MOTOR NAMEPLATE RPM
MOTOR NAMEPLATE KW
INTERTER PWM FREQUENCY
SAFETY CODE CERTIFICATION
THE COMPRESSOR MOTOR CONTROLLER AND OVERLOAD PROTECTION MUST BE
IN ACCORDANCE WITH CARRIER SPECIFICATION Z-420.
19XV05008701 REV. 3
Fig. 8 — Machine Nameplate
DEFAULT VALUE
460
Yes
460
200
100
100
200
100
3456
100
1
102.0
102.0
102.0
0.0
10
10
40
10
40
10
30
30
DSABLE
* Parameters marked with an * are not downloadable to the VFD but are used
in other calculations and algorithms in the ICVC.
NOTES:
1. Parameters in italics are to be entered or confirmed at start-up.
2. Parameters in bold are to be changed only after consultation with service engineering.
Commissioning the Unit — The commission procedure is as follows:
1. If the chiller has been stored outdoors, allow at least 24
hours room temperature stabilization prior to commissioning. Ensure any condensation that occurs as a result
of the ambient temperature is allowed to evaporate.
2. Enter parameters in the VFD_CONF screen.
3. Install surge suppression devices if required.
4. Review the power wiring and grounding to ensure that it
has been properly connected.
5. Visually examine the inside of the drive enclosure to:
a. Look for signs of corrosion or moisture residue.
b. Remove any dirt or debris.
c. Make sure all vents are clear.
6. Apply power to the drive and take thermal measurements
of the capacitor bank and power connections. Do this
again before start-up.
7. Measure and record the incoming line voltage. Line-toline voltages should be balanced within 3% as calculated
by Rockwell’s procedure below:
Measure voltages phase-to-phase and phase-to-ground.
a191924
Fig. 9 — Drive Module Label
6
b. Check motor and wiring insulation.
c. Check parameter settings on VFD_CONF screen
in the ICVC.
Vmax = Maximum measured phase-to-phase voltage
(A to B, B to C, C to A)
Vmin = Minimum measured phase-to-phase voltage
Imbalance Calculation Formula
Check Internal Jumpers — On the Main VFD Control board there are two jumpers labeled J1 HARDWARE ENABLE and J2 SAFETY ENABLE. J1 should be removed and
J2 should be in place. See Fig. 10.
There are two jumper wires that connect a particular terminal to chassis ground. The MOV and AC EMI jumper should
be connected to the PE-A terminal. The COMMON MODE
CAPACITORS to GROUND jumper should be connected to a
standoff rather than the PE-B terminal.
Use the recommended tools as follows when connecting
jumper wires in Frame 6 and in Frame 7:
• Recommended torque (screws and nuts) = 1.36 N·m
(120.0 lb·in)
• Recommended hex socket = 7 mm
• Recommended screwdriver = T20 star type
See Fig. 11A and Fig. 11B for the correct positions of the
jumpers.
(VAB + VBC + VCA)
3
(Vmax – Vmin) x 100
Imbalance % =
Vavg
8. Take a final thermal measurement of the capacitor bank
and power after finalizing the installation to ensure all
connections are good.
9. If a ground fault occurs, then do the following:
a. Check for a ground in the motor or motor wiring.
b. Check for damage to wiring insulation and that
wiring is dry.
c. Verify the motor wiring is separated from ground
and there is no connection between phases.
d. Check for failed IGBTs.
10. If an Overcurrent fault occurs, then do the following:
a. Check for excessive load and verify load limit settings on the ICVC.
Vavg
=
LEGEND
NO.
1
2
NAME
HIM Connector
Fan Connector
Battery
Receptacle
3
4
5
6
7
8
9
DESCRIPTION
DPI Port 1 (HIM Cradle) connection.
Power supply for internal cooling fan
(Frames 2 & 3).
User installed CR1220 lithium coin cell
battery provides power to the Real Time
Clock (Optional, not supplied).
DPI Port 2
Cable connection for handheld and
remote HIM options.
Embedded EtherNet/ Rotary switches for setting lowest octet
IP Address Selectors of EtherNet address (forces address to
192.168.1.xxx).
Embedded EtherNet/ Network cable connection.
IP Connector
Jumper J2 SAFETY Safety enable jumper. Removed when
safety option is installed.
Jumper J1 ENABLE Hardware enable jumper. Removed
when a hardware enable configuration is
utilized.
TB1
I/O terminal block.
a19-1921
TB1 I/O Terminal Designations
FIXED I/O
Di 0ac
Di C
Di 0dc
TERMINAL
Di 0ac
Di C
Di 0dc
+24V
+24V
24VC
NAME
Digital Input 120V AC
DESCRIPTION
Connections for AC power supply.
Digital Input Common
Digital input common
Digital Input 24V DC
Connections for DC power supply.
+24 Volt Power
Connections for drive supplied 24V power.
24 Volt Common
24VC
IMPORTANT: Wiring to pluggable terminal block connectors
should be supported by wire ties or other means to help prevent unintentional disconnection
Fig. 10 — PF755 Main Control Board
7
Troubleshooting the Drive — The drive can display
two kinds of error codes on the ICVC called the Alert and
Alarm codes. These codes signal a problem detected during
self tuning or drive operation. Alert and Alarm codes are located in the 19XRV Start-Up, Operation and Maintenance Instructions. Note the following differences between Carrier and
Allen-Bradley terminology:
• A warning message on the ICVC is an ALERT.
• The same warning viewed with Rockwell Drive Explorer
is a VFD ALARM.
• A failure resulting in a shutdown is seen as an ALARM
on the ICVC and as a VFD FAULT when viewed with
Drive Explorer.
CONDITION CODES
ICVC ALERT
=
VFD ALARM
ICVC ALARM
=
VFD FAULT
See Tables 3-6 and Fig. 12.
ICVC ALERT CODES — An alert condition is indicated by
a message at the top of the ICVC default screen. In addition, an
exclamation point (!) will appear next to any affected point on
an ICVC display screen. The drive will continue to operate
during the alert condition. Investigate the cause of the alert to
ensure it does not lead to a fault condition. The alert code will
automatically be cleared from the ICVC when the condition
causing the alert no longer exists. See Table 4.
ICVC ALARM CODES — An alarm condition is also indicated by a message at the top of the ICVC default screen. If an
alarm occurs, the drive coasts to stop. The STS (status) light on
the drive will turn from Green to Red or Yellow (see Table 3).
The detected fault message is maintained on the display until it
is cleared by pressing the RESET softkey. See Table 5.
TEST EQUIPMENT NEEDED TO TROUBLESHOOT —
An isolated multimeter adequately rated for the DC bus voltage will be needed to measure DC bus voltage and to make
resistance checks. Note that dedicated troubleshooting test
points are not provided.
A19-1835
Fig. 11A — Jumper Wire Locations — Frame 6
Allen-Bradley
A19-1836
7
Fig. 11B — Jumper Wire Locations — Frame 7
4
1
8
5
2
9
6
3
SERVICE
WARNING
DC bus capacitors retain hazardous voltages after input
power has been disconnected. After disconnecting input
power, wait five (5) minutes for the DC bus capacitors to
discharge and then check the voltage with a voltmeter to
ensure the DC bus capacitors are discharged before touching any internal components. Failure to observe this precaution could result in severe bodily injury or loss of life.
A1
91815
Fig. 12 — Drive Status Indicator
8
Table 3 — Drive Status Indicator Descriptions
NAME
STS (Status)
ENET
LINK
COLOR
Green
Yellow
STATE
Flashing
Steady
Flashing
Red
Steady
Flashing
Red/Yellow
Steady
Flashing Alternately
Green/Red
None (Unlit)
Flashing Alternately
Off
Red
Flashing
Steady
Flashing Alternately
Flashing
Red/Green
Green
None (Unlit)
Green
Steady
Off
Flashing
Steady
DESCRIPTION
Drive ready but not running, and no faults are present.
Drive running, no faults are present.
Drive is not running. A type 2 (non-configurable) alarm condition exists and the
drive cannot be started.
Drive is not running, a type 1 alarm condition exists. The drive can be started.
A major fault has occurred. Drive cannot be started until fault condition is
cleared.
A non-resettable fault has occurred.
A minor fault has occurred. When running, the drive continues to run. System is
brought to a stop under system control. Fault must be cleared to continue. Use
parameter 950 [Minor Flt Config] to enable. If not enabled, acts like a major
fault.
Drive is flash updating.
Adapter and/or network is not powered, adapter is not properly connected to
the network, or adapter needs an IP address.
An EtherNet/IP connection has timed out.
Adapter failed the duplicate IP address detection test.
Adapter is performing a self-test.
Adapter is properly connected but is not communicating with any devices on
the network.
Adapter is properly connected and communicating on the network.
Adapter is not powered or is not transmitting on the network.
Adapter is properly connected and transmitting data packets on the network.
Adapter is properly connected but is not transmitting on the network.
NOTES:
1. A Type 1 alarm indicates that a condition exists. Type 1 alarms
are user configurable.
2. A Type 2 alarm indicates that a configuration error exists and
the drive cannot be started. Type 2 alarms are not configurable.
VERIFYING THAT DC BUS CAPACITORS ARE DISCHARGED — The drive’s DC bus capacitors retain hazardous voltages after input power has been disconnected. Perform
the following steps before touching any internal components:
1. Turn off and lock out input power. Wait five minutes.
2. Verify that there is no voltage at the drive’s input power
terminals.
3. Measure the DC bus potential with a voltmeter while
standing on a non-conductive surface and wearing insulated gloves (1000 V). Measure the DC bus potential. See
Fig. 5 for the 248-amp drive and Fig. 6 for the 361 and
477-amp drives. The voltage between DC+ and DC-, and
from each DC terminal to the chassis must be zero before
proceeding.
4. Once the drive has been serviced, reapply input power.
HIGH TEMPERATURE ALARMS — Coolant flow
through the cold plate is controlled by an orifice in the refrigerant line leaving the cold plate. The orifice looks like one of the
O-ring face seal connectors and in fact is used as one of the
connections on the coolant tubing. The difference is that the
passage through the fitting is 0.375 in. (9.5 mm). If the orifice
is present and condenser liquid flow is present, the liquid will
flash to cooler temperature at the orifice. This temperature difference is great enough to be easily felt.
MAIN CONTROL BOARD (MCB) COMPONENTS —
Figure 13 shows the drive module with the cover removed. To
access the control boards, loosen the screw on the face of the
keypad mount and swing the keypad mount upward.
The components on the main control board (MCB) are
shown in Fig. 14. Note the location of the terminals labeled
MCB I/O. The high pressure switch is wired to these terminals
as shown in Fig. 15. In the event of a high condenser pressure
alarm, the connections at these terminals should be checked
and tightened if necessary.
A typical wiring schematic is shown in Appendix A.
SWING UP KEY PAD
MOUNT TO ACCESS
CONTROL BOARDS
a19-1843
Fig. 13 — Drive Module with Cover Removed
9
DPI PORT 02 (COMPUTER PORT)
DIGITAL INPUT TERMINAL BLOCKS
(SLOTS 04 & 05)
ETHERNET/IP ADDRESS SWITCHES
DIGITAL OUTPUT TERMINAL BLOCKS
(SLOTS 04 & 05)
EMBEDDED ETHERNET/IP PORT
MCB I/O TERMINALS
(AUX FAULT /
HIGH PRESSURE FAULT /
ENABLE INPUT)
Fig. 14 — MCB (Main Control Board) Components
a19-1844
*Located outside of starter; connected by field wiring.
Fig. 15 — High Pressure Switch Wiring
a19-1925
10
Table 4 — ICVC Alert Codes
PRE-START ALERTS: These alerts only delay start-up. When alert is corrected, the start-up will continue. No reset is
necessary.
ICVC FAULT
STATE
100
PRIMARY
MESSAGE
PRESTART
ALERT
PRESTART
ALERT
SECONDARY
MESSAGE
STARTS LIMIT
EXCEEDED
HIGH BEARING
TEMPERATURE
102
PRESTART
ALERT
HIGH MOTOR
TEMPERATURE
103
PRESTART
ALERT
HIGH
DISCHARGE
TEMP
104
PRESTART
ALERT
LOW
REFRIGERANT
TEMP
105
PRESTART
ALERT
PRESTART
ALERT
LOW OIL
TEMPERATURE
HIGH
CONDENSER
PRESSURE
107
PRESTART
ALERT
LOW LINE
VOLTAGE
108
PRESTART
ALERT
HIGH LINE
VOLTAGE
109
PRESTART
ALERT
GUIDE VANE
CALIBRATION
110
PRESTART
ALERT
HIGH
RECTIFIER
TEMP
111
PRESTART
ALERT
HIGH
INVERTER
TEMP
101
106
PRIMARY CAUSE
ADDITIONAL CAUSE/REMEDY
100Excessive compressor starts
(8 in 12 hours).
101Comp Thrust Brg Temp [VALUE]
exceeded limit of [LIMIT]*.
Depress the RESET softkey if additional start
is required. Reassess start-up requirements.
Check oil heater for proper operation.
Check for low oil level, partially closed oil supply valves, clogged oil filters.
Check the sensor wiring and accuracy.
Check Comp Thrust Brg Alert setting in
SETUP1 screen.
102Comp Motor Winding Temp
Check motor sensors for wiring and accuracy.
[VALUE] exceeded limit of [LIMIT]*.
Check motor cooling line for proper operation,
or restrictions.
Check for excessive starts within a short time
span.
Check Comp Motor Temperature Override
setting in SETUP1 screen.
103Comp Discharge Temp [VALUE] Allow discharge sensor to cool.
exceeded limit of [LIMIT]*.
Check sensor wiring and accuracy.
Check for excessive starts.
Check Comp Discharge Alert setting in
SETUP1 screen.
104Evaporator Refrig Temp [VALUE] Check transducer wiring and accuracy.
exceeded limit of [LIMIT]*.
Check for low chilled fluid supply
temperatures.
Check refrigerant charge.
Check Refrig Override Delta T in SETUP1
screen.
105Oil Sump Temp [VALUE]
Check oil heater contactor/relay and power.
exceeded limit of [LIMIT]*.
Check oil level and oil pump operation.
106Condenser Pressure [VALUE]
Check transducer wiring and accuracy.
exceeded limit of [LIMIT]*.
Check for high condenser water
temperatures.
Check high condenser pressure switch wiring.
107Percent Line Voltage [VALUE]
Check voltage supply.
exceeded limit of [LIMIT]*.
Check voltage transformers and switch gear.
Consult power utility if voltage is low.
108Percent Line Voltage [VALUE]
Check voltage supply.
exceeded limit of [LIMIT]*.
Check power transformers.
Consult power utility if voltage is high.
109Actual Guide Vane Pos
Press STOP button on ICVC and perform
Calibration Required Before Startup.
Guide Vane Calibration in Controls Test
screen.
Check guide vane actuator feedback
potentiometer.
110Rectifier Temperature [VALUE]
Check that VFD refrigerant isolation valves
exceeded limit of [LIMIT]*.
are open.
Check VFD refrigerant cooling solenoid and
refrigerant strainer.
Check for proper VFD cooling fan operation
and blockage.
111Inverter Temperature [VALUE]
Check that VFD refrigerant isolation valves
exceeded limit of [LIMIT]*.
are open.
Check VFD refrigerant cooling solenoid and
refrigerant strainer.
Check for proper VFD cooling fan operation
and blockage.
*[LIMIT] is shown on the ICVC as temperature, pressure, voltage, etc., predefined or selected by the operator as an override or an alert. [VALUE] is
the actual pressure, temperature, voltage, etc., at which the control tripped.
11
Table 4 — ICVC Alert Codes (cont)
NORMAL RUN WITH OVERRIDES
ICVC FAULT
PRIMARY
STATE
MESSAGE
120
RUN CAPACITY
LIMITED
SECONDARY
MESSAGE
HIGH CONDENSER
PRESSURE
PRIMARY CAUSE
120Condenser Pressure
[VALUE] exceeded limit of
[LIMIT]*.
121
RUN CAPACITY
LIMITED
HIGH MOTOR
TEMPERATURE
121Comp Motor Winding
Temp [VALUE] exceeded
limit of [LIMIT]*.
122
RUN CAPACITY
LIMITED
LOW EVAP REFRIG
TEMP
122Evaporator Refrig
Temp [VALUE] exceeded
limit of [LIMIT]*.
123
RUN CAPACITY
LIMITED
HIGH COMPRESSOR
LIFT
123Surge Prevention
Override: Lift Too High For
Compressor
124
RUN CAPACITY
LIMITED
MANUAL GUIDE VANE
TARGET
124Run Capacity Limited:
Manual Guide Vane Target.
125
RUN CAPACITY
LIMITED
LOW DISCHARGE
SUPERHEAT
No Alert message.
126
RUN CAPACITY
LIMITED
HIGH RECTIFIER TEMP 126Rectifier Temperature
[VALUE] exceeded limit of
[LIMIT]*.
127
RUN CAPACITY
LIMITED
RUN CAPACITY
LIMITED
MANUAL SPEED
CONTROL
HIGH INVERTER TEMP
128
No Alert message.
128Inverter Temperature
[VALUE] exceeded limit of
[LIMIT]*.
ADDITIONAL CAUSE/REMEDY
Check condenser water pump operation.
Check for high condenser water temperatures or
low flow rate. Verify that isolation valves are
open.
Check Cond Press Override setting in SETUP1.
Check for closed valves or restriction in motor
cooling lines.
Check for closed refrigerant isolation valves.
Check Comp Motor Temp Override setting in
SETUP1.
Check refrigerant charge.
Check that optional cooler liquid line isolation
valve is fully open.
Check for excessive condenser flow or low
chilled water flow.
Check for low entering cooler temperature.
Check that condenser inlet and outlet water
nozzles are piped correctly.
Check for waterbox division plate gasket bypass.
Check for high condenser water temperature or
low suction temperature.
Check for high Evaporator or Condenser
approaches.
Check surge prevention parameters in
OPTIONS screen.
Target Guide Vane Position has been forced in
the COMPRESS screen. Select and RELEASE
force to return to normal (automatic) operation.
Check for oil loss or excess refrigerant charge.
Verify that the valves in the oil reclaim lines are
open.
Check Rectifier Temp Override in SETUP1
screen.
Check that VFD refrigerant isolation valves are
open.
Check VFD refrigerant cooling solenoid.
Check for proper VFD cooling fan operation and
blockage.
Chiller is not in automatic temperature control.
Check Inverter Temp Override in SETUP1
screen.
Check that VFD refrigerant isolation valves are
open.
Check VFD refrigerant cooling solenoid.
Check for proper VFD cooling fan operation and
blockage.
*[LIMIT] is shown on the ICVC as the temperature, pressure, voltage, etc., set point predefined or selected by the operator as an override, alert, or
alarm condition. [VALUE] is the actual pressure, temperature, voltage, etc., at which the control tripped.
12
Table 4 — ICVC Alert Codes (cont)
CHILLER ALERTS
ICVC FAULT
PRIMARY
STATE
MESSAGE
140
SENSOR ALERT
SECONDARY
MESSAGE
LEAVING COND WATER
TEMP
ENTERING COND WATER
TEMP
CHECK OIL FILTER
141
SENSOR ALERT
142
LOW OIL
PRESSURE ALERT
143
AUTORESTART
PENDING
LINE CURRENT
IMBALANCE
144
AUTORESTART
PENDING
LINE VOLTAGE
DROP OUT
145
AUTORESTART
PENDING
AUTORESTART
PENDING
AUTORESTART
PENDING
HIGH LINE VOLTAGE
POWER LOSS
149
AUTORESTART
PENDING
SENSOR ALERT
150
SENSOR ALERT
HIGH BEARING
TEMPERATURE
151
CONDENSER
PUMP RELAY
PRESSURE ALERT ENERGIZED
152
RECYCLE ALERT
EXCESSIVE RECYCLE
STARTS
153
no message:
ALERT
only
POTENTIAL
FREEZE-UP
no message; ALERT only
155
OPTION SENSOR
FAULT
REMOTE RESET
SENSOR
156
OPTION SENSOR
FAULT
AUTO CHILLED WATER
RESET
157
OPTION SENSOR
FAULT
AUTO DEMAND LIMIT
INPUT
158
SENSOR ALERT
SPARE TEMPERATURE
#1
146
147
148
154
LOW LINE VOLTAGE
VFD MODULE RESET
PRIMARY CAUSE
140Sensor Fault: Check
Leaving Cond Water Sensor.
141Sensor Fault: Check
Entering Cond Water Sensor.
142Low Oil Pressure Alert.
Check Oil Filter.
143Line Current Imbalance: Check VFD Fault History for Values.
144Single Cycle Line
Voltage Dropout.
145High Percent Line
Voltage [VALUE].
146Low Percent Line
Voltage [VALUE].
147->VFD Module Power-On
Reset When Running.
148Control Power-Loss
When Running.
HIGH DISCHARGE TEMP 149Comp Discharge Temp
[VALUE] Exceeded Limit of
[LIMIT]*.
COND PRESS/TEMP
TOO LOW
ADDITIONAL CAUSE/REMEDY
Check sensor resistance or voltage drop.
Check for proper wiring.
Check sensor resistance or voltage drop.
Check for proper wiring.
Check for partially or closed shut-off valves.
Check oil filter.
Check oil pump and power supply.
Check oil level.
Check for foaming oil at start-up.
Check transducer wiring and accuracy.
Power loss has been detected in any phase.
Chiller automatically restarting.
A drop in line voltage has been detected within
2 voltage cycles.
Chiller automatically restarting if Auto Restart is
enabled in OPTIONS screen.
Check phase to phase and phase to ground line
power.
Check phase to phase and phase to ground line
power.
VFD Module has detected a hardware fault due
to electrical noise, power loss or software and
has reset. Chiller automatically restarting.
Check for power loss and sources of electromagnetic interference.
Check 24 vac control power supply to ICVC.
Check sensor resistance or voltage drop.
Check for proper wiring.
Check for proper inlet guide vane and optional
diffuser actuator operation.
Check for proper condenser flow and
temperature.
Check for high lift or low load.
Check for fouled tubes or noncondensables in
the chiller.
150Comp Thrust Brg Temp Check sensor resistance or voltage drop.
[VALUE] exceeded limit of
Check for proper wiring.
[LIMIT]*.
Check for partially closed service valves.
Check oil cooler TXV.
Check oil level and oil temperature.
151High Condenser Pres- Check sensor wiring and accuracy.
Check condenser flow and water temperature.
sure [VALUE]: Pump Energized to Reduce Pressure.
Check for fouled tubes.
This alarm is not caused by the High Pressure
Switch.
152Excessive recycle
Chiller load is too low to keep compressor on
starts.
line and there has been more than 5 starts in
4 hours.
Increase chiller load, adjust hot gas bypass,
increase RECYCLE RESTART DELTA T from
SETUP1 Screen.
153Lead/Lag DisabledIllegal chiller address configuration in Lead/Lag
Config: Duplicate Chiller
screen. Both chillers require a different address.
Address.
154Condenser freeze up
The condenser pressure transducer is reading a
prevention.
pressure that could freeze the condenser tubes.
Check for condenser refrigerant leaks.
Check fluid temperature.
Check sensor wiring and accuracy.
Place the chiller in PUMPDOWN mode if the
vessel is evacuated.
155Sensor Fault/Option
Check sensor resistance or voltage drop.
Disabled: Remote Reset
Check for proper wiring to CCM connector J4.
Sensor.
156Sensor Fault/Option
Check sensor resistance or voltage drop.
Disabled: Auto Chilled Water Check for proper wiring to CCM connector J5.
Reset.
157Sensor Fault/Option
Check sensor resistance or voltage drop.
Disabled: Auto Demand Limit Check for proper wiring to CCM connector J5.
Input.
158Spare Temperature 1
Check sensor resistance or voltage drop.
[VALUE] exceeded limit of
Check for proper wiring to CCM connector J4.
[LIMIT]*.
Check Spare Temp #1 Limit in SETUP1 screen.
*[LIMIT] is shown on the ICVC as the temperature, pressure, voltage, etc., set point predefined or selected by the operator as an override, alert, or
alarm condition. [VALUE] is the actual pressure, temperature, voltage, etc., at which the control tripped.
13
Table 4 — ICVC Alert Codes (cont)
CHILLER ALERTS (cont)
ICVC FAULT
PRIMARY
STATE
MESSAGE
159
SENSOR ALERT
SECONDARY
MESSAGE
SPARE TEMPERATURE
#2
PRIMARY CAUSE
159Spare Temperature 2
[VALUE] exceeded limit of
[LIMIT]*.
161WSM Cool Source —
Loss of Communication.
161
LOSS OF
COMMUNICATION
WITH WSM
162
SENSOR ALERT
EVAPORATOR
APPROACH
163
SENSOR ALERT
CONDENSER APPROACH 163Condenser Approach
[VALUE] Exceeded Limit of
[LIMIT]*.
164
VFD SPEED ALERT LOW VFD SPEED
165
AUTORESTART
PENDING
166
AUTORESTART
PENDING
167
SYSTEM ALERT
168
SENSOR ALERT
162Evaporator Approach
[VALUE] Exceeded Limit of
[LIMIT]*.
164Actual VFD Speed
exceeded limit of Target VFD
Speed –10%.
LOW DC BUS VOLTAGE
165Low DC Bus Voltage:
[VALUE] Exceeded Limit of
[LIMIT]*.
HIGH DC BUS VOLTAGE
166High DC Bus Voltage:
[VALUE] Exceeded Limit of
[LIMIT]*.
HIGH DISCHARGE TEMP 167Comp Discharge Temp
[VALUE] exceeded limit of
[LIMIT]*.
HUMIDITY SENSOR
INPUT
ADDITIONAL CAUSE/REMEDY
Check sensor resistance or voltage drop.
Check for proper wiring to CCM connector J4.
Check Spare Temp #2 Limit in SETUP1 screen.
Check settings in WSMDEFME screen.
Check CCN communications link with WSM
(Water System Manager) Module.
Check Supervisory Part of WSM.
Check that refrigerant charge level is adequate,
waterbox division plate gaskets are sealing,
evaporator tubes are not fouled and that oil
reclaim system is working.
Check sensor resistance or voltage drop.
Check for proper wiring.
Check Evap Approach Alert setting in SETUP1
screen.
Check sensors resistance or voltage drop.
Check for proper wiring.
Check Cond Approach Alert setting in SETUP1
screen.
Check for noncondensable gas in the
condenser.
Check that the condenser tubes are not fouled.
Actual VFD Speed on COMPRESS screen must
be at least 90% of Target VFD Speed.
Verify phase to phase and phase to ground line
voltage.
Verify phase to phase and phase to ground line
voltage. Monitor AC line for high transient voltage conditions.
Check sensor resistance or voltage drop.
Check for proper wiring.
Check for excessive starts.
Check Comp Discharge Alert setting in SETUP1
screen.
168Sensor Fault: Check
Check humidity sensor wiring on CCM connecHumidity Sensor Input Sensor. tors J3 and J5. CCM switch SW2-1 must be in
“OFF” position.
Check Humidity Sensor Input in Controls Test.
*[LIMIT] is shown on the ICVC as the temperature, pressure, voltage, etc., set point predefined or selected by the operator as an override, alert, or
alarm condition. [VALUE] is the actual pressure, temperature, voltage, etc., at which the control tripped.
14
Table 5 — ICVC Alarm Codes
CHILLER PROTECTIVE LIMIT FAULTS
ICVC FAULT
PRIMARY
SECONDARY
PRIMARY CAUSE
STATE
MESSAGE
MESSAGE
200
PROTECTIVE LIMIT RECTIFIER POWER
200Rectifier Power Fault:
FAULT
Check VFD Status.
201
PROTECTIVE LIMIT INVERTER POWER FAULT 201Inverter Power Fault:
Check VFD Status.
202
PROTECTIVE LIMIT MOTOR AMPS NOT
202Motor Amps Not
SENSED
Sensed — Average Load
Current [VALUE].
203
FAILURE TO START MOTOR ACCELERATION 203Motor Acceleration Fault
FAULT
— Average Load Current
[VALUE].
204
FAILURE TO STOP
205
PROTECTIVE LIMIT HIGH DC BUS VOLTAGE
206
PROTECTIVE LIMIT VFD FAULT
207
208
209
210
211
212
213
214
215
216
217
218
219
VFD SHUTDOWN FAULT
204VFD Shutdown Fault:
Check Inverter Power Unit.
205High DC Bus Voltage:
[VALUE] exceeded limit of
[LIMIT]*.
ADDITIONAL CAUSE/REMEDY
Malfunction within VFD Power Module.
Call Carrier Service.
Malfunction within VFD Power Module.
Call Carrier Service.
Check main circuit breaker for trip. Increase
Current % Imbalance in VFD_CONF screen.
Check that inlet guide vanes are fully closed at
start-up.
Check Motor Rated Load Amps in VFD_CONF
screen. Reduce unit pressure if possible.
VFD Circuit Board malfunction.
Call Carrier Service.
Verify phase to phase and phase to ground line
voltage. Monitor AC line for high transient voltage conditions. VFD Circuit Board malfunction.
Call Carrier Service.
See VFD Fault Code description and corrective
action.
206VFD Fault Code:
[VALUE]; Check VFD Fault
Code List.
PROTECTIVE LIMIT HIGH CONDENSER
207High Cond Pressure
Check Compressor Discharge High Pressure
PRESSURE
trip. [VALUE] exceeded Switch switch wiring and accuracy.
Trippoint.
Check for high condenser water temperatures,
low water flow, fouled tubes.
Check for division plate/gasket bypass.
Check for noncondensables in refrigerant.
PROTECTIVE LIMIT EXCESSIVE MOTOR
208Percent Load Current
Check Motor Rated Load Amps in VFD_CONF
AMPS
[VALUE] exceeded limit of
screen. Percent Load Current > 110%.
[LIMIT]*.
Check Motor Rated Load Amps setting.
PROTECTIVE LIMIT LINE CURRENT
209Line Current ImbalCheck phase to phase and phase to ground
IMBALANCE
ance: Check VFD Fault Hispower distribution bus voltage.
tory for Values.
Check Line Current % Imbalance in VFD_CONF
screen. Consult power company.
PROTECTIVE LIMIT LINE VOLTAGE DROPOUT 210Single Cycle Line Volt- Temporary loss of voltage. Disable Single Cycle
age Dropout.
Dropout in VFD_CONF screen.
PROTECTIVE LIMIT HIGH LINE VOLTAGE
211High Percent Line Volt- Check phase to phase and phase to ground disage [VALUE].
tribution bus voltage. Consult power company.
PROTECTIVE LIMIT LOW LINE VOLTAGE
212Low Percent Line Volt- Check phase to phase and phase to ground disage [VALUE].
tribution bus voltage. Consult power company.
PROTECTIVE LIMIT VFD MODULE RESET
213VFD Module Power-On Temporary loss of VFD control voltage. Check
Reset When Running.
VFD control power breaker, transformer and
fuses.
PROTECTIVE LIMIT POWER LOSS
214Control Power Loss
Check phase to phase and phase to ground disWhen Running.
tribution bus voltage.
Check VFD fuses.
Check 24 vac power supply to ICVC.
Consult power company.
PROTECTIVE LIMIT LOW DC BUS VOLTAGE
215Low DC Bus Voltage:
Verify phase-to-phase and phase-to-ground line
[VALUE] exceeded limit of
voltage. VFD Circuit Board malfunction.
[LIMIT]*.
Call Carrier Service.
PROTECTIVE LIMIT LINE VOLTAGE
216Line Voltage ImbalCheck phase-to-phase and phase-to-ground
IMBALANCE
ance. Check VFD Fault Hisdistribution bus voltage. Increase Line Voltage
tory for Values.
% Imbalance in VFD_CONF screen.
PROTECTIVE LIMIT MOTOR OVERLOAD TRIP 217Motor Overload Trip;
Any phase current > 106% Rated Load Amps.
Check VFD configurations.
Can result from significant load side current
imbalance when running at full load.
Check entering condenser water temperature
and water flow rate.
Check Motor Rated Load Amps in VFD_CONF
screen.
PROTECTIVE LIMIT VFD RECTIFIER
218VFD Rectifier Temp
Check that VFD refrigerant isolation valves are
OVERTEMP
Exceeded: Check Cooling and open.
VFD Config.
Check VFD refrigerant cooling solenoid and
refrigerant strainer.
Check for proper VFD cooling fan operation and
blockage.
PROTECTIVE LIMIT VFD INVERTER
219VFD Inverter Temp
Check that VFD refrigerant isolation valves are
OVERTEMP
Exceeded: Check Cooling and open.
VFD Config.
Check VFD refrigerant cooling solenoid and
refrigerant strainer.
Check for proper VFD cooling fan operation and
blockage.
*[LIMIT] is shown on the ICVC as the temperature, pressure, voltage, etc., set point predefined or selected by the operator as an override, alert, or
alarm condition. [VALUE] is the actual pressure, temperature, voltage, etc., at which the control tripped.
NOTE: ICVC Alarms 212-226 are declared as a result of VFD Faults.
15
Table 5 — ICVC Alarm Codes (cont)
CHILLER PROTECTIVE LIMIT FAULTS (cont)
ICVC FAULT
PRIMARY
SECONDARY
STATE
MESSAGE
MESSAGE
220
PROTECTIVE LIMIT GROUND FAULT
221
222
PROTECTIVE LIMIT UNUSED
PROTECTIVE LIMIT LINE FREQUENCY TRIP
223
LOSS OF
COMMUNICATION
224
PROTECTIVE LIMIT
225
PROTECTIVE LIMIT
226
PROTECTIVE LIMIT
227
PROTECTIVE LIMIT
228
PROTECTIVE LIMIT
229
PROTECTIVE LIMIT
230
PROTECTIVE LIMIT
231
PROTECTIVE LIMIT
232
PROTECTIVE LIMIT
PRIMARY CAUSE
220Ground Fault Trip;
Check Motor and Current
Sensors.
ADDITIONAL CAUSE/REMEDY
Check for condensation on motor terminals.
Check motor power leads for phase to phase or
phase to ground shorts. Disconnect motor from
VFD and megger motor.
Call Carrier Service.
221UNUSED
222Line Frequency —
[VALUE] exceeded limit of
[LIMIT]; Check Power Supply.
223Loss of SIO Comm with
VFD Gateway: Check VFG
Module and Power.
If operating from a generator, check generator
size and speed.
Check utility power supply.
WITH VFD GATEWAY
Check VFD communication wiring and
MODULE
connectors on VFD Gateway and DPI board.
Check for compatibility between ICVC and
Gateway software.
VFD COMMUNICATIONS 224Loss of DPI Comm with Check VFD communication wiring and
FAULT
VFD Gateway: Check VFG to connectors.
VFD Comm.
Check status lights on DPI Communications
Interface Board.
Call Carrier Service.
MOTOR CURRENT
225Motor Current ImbalCheck Motor Current % Imbalance in
IMBALANCE
ance: Check VFD Fault
VFD_CONF screen.
History for Values.
LINE PHASE REVERSAL 226Line Phase Reversal:
Reverse connections of any two line conductors
Check Line Phases.
to circuit breaker.
OIL PRESS SENSOR
227Oil Pressure Delta P
Check transducer wiring and accuracy.
FAULT
[VALUE] (Pump Off): Check
Check power supply to pump.
Pump/Transducers.
Check pump operation.
Check transducer calibration.
LOW OIL PRESSURE
228Low Operating Oil
Check transducer wiring and accuracy.
Pressure [VALUE]: Check Oil Check power supply to pump.
Pump and Filter.
Check pump operation.
Check oil level.
Check for partially closed service valves.
Check oil filters.
Check for foaming oil at start-up.
Check transducer calibration.
LOW CHILLED WATER
229Low Chilled Water Flow; Perform pump control test.
FLOW
Check Switch/Delta P Config Check optional transducer calibration and
& Calibration.
wiring.
Check Evaporator Refrigerant Temperature
sensor.
Check chilled water valves.
Check for evaporator saturation temperature
< 34 F if not in Pumpdown Lockout mode. Place
unit in Pumpdown mode before removing
charge.
230Low Condenser Water Perform pump control test.
LOW CONDENSER
WATER FLOW
Flow; Check Switch/Delta P
Check optional transducer calibration and
Config & Calibration.
wiring.
Check condenser water valves.
Check for COND PRESS OVERRIDE + 5 psig.
HIGH DISCHARGE TEMP 231Comp Discharge Temp Check for closed compressor discharge isola[VALUE] Exceeded Limit of
tion valve.
[LIMIT]*.
Check if chiller was operating in surge.
Check sensor resistance or voltage drop.
Check for proper wiring.
Check for proper condenser flow and
temperature.
Check compressor discharge isolation valve.
Check for proper inlet guide vane and optional
diffuser actuator operation.
LOW REFRIGERANT
232Evaporator Refrig Temp Check for proper refrigerant charge.
TEMP
[VALUE] exceeded limit of
Check float valve operation.
[LIMIT]*.
Check for closed condenser liquid line isolation
valve. If problem occurs at high load, check for
low condenser pressure which causes inadequate flasc orifice differential pressure.
Check for proper water flow and temperature.
Confirm that condenser water enters bottom row
of condenser tubes first.
Check Evaporator Refrigerant Temperature
sensor.
Check for division plate gasket bypass.
Check for fouled tubes.
*[LIMIT] is shown on the ICVC as the temperature, pressure, voltage, etc., set point predefined or selected by the operator as an override, alert, or
alarm condition. [VALUE] is the actual pressure, temperature, voltage, etc., at which the control tripped.
16
Table 5 — ICVC Alarm Codes (cont)
CHILLER PROTECTIVE LIMIT FAULTS (cont)
ICVC FAULT
PRIMARY
SECONDARY
STATE
MESSAGE
MESSAGE
233
PROTECTIVE LIMIT HIGH MOTOR
TEMPERATURE
PRIMARY CAUSE
233Comp Motor Winding
Temp [VALUE] exceeded
limit of [LIMIT]*.
234
PROTECTIVE LIMIT HIGH BEARING
TEMPERATURE
234Comp Thrust Brg Temp
[VALUE] exceeded limit of
[LIMIT]*.
235
PROTECTIVE LIMIT HIGH CONDENSER
PRESSURE
235Condenser Pressure
[VALUE] exceeded limit of
[LIMIT]*.
236
PROTECTIVE LIMIT COMPRESS SURGE/
LOW SPEED
236Compressor Surge:
Check condenser water temp
and flow.
237
PROTECTIVE LIMIT SPARE SAFETY
DEVICE
237Spare Safety Device.
238
PROTECTIVE LIMIT EXCESSIVE COMPR
SURGE
238Compressor Surge:
Check condenser water temp
and flow.
239
PROTECTIVE LIMIT TRANSDUCER
VOLTAGE FAULT
239Transducer Voltage Ref
[VALUE] exceeded limit of
[LIMIT]*.
240
PROTECTIVE LIMIT LOW DISCHARGE
SUPERHEAT
240Check for Oil in Or
Overcharge of Refrigerant.
241
PROTECTIVE LIMIT RECTIFIER
OVERCURRENT
LOSS OF
WITH CCM MODULE
COMMUNICATION
241Rectifier Overcurrent
Fault: Check VFD Status.
242Loss of Communication With CCM, Check
Comm. Connectors.
243Evaporator Refrig
Temp [VALUE] exceeded
limit of [LIMIT]*.
242
243
POTENTIAL
FREEZE-UP
EVAP PRESS/TEMP
TOO LOW
244
POTENTIAL
FREEZE-UP
COND PRESS/TEMP
TOO LOW
244Condenser Refrig
Temp [VALUE] exceeded
limit of [LIMIT]*.
ADDITIONAL CAUSE/REMEDY
Check motor sensors wiring and accuracy.
Check motor cooling line and spray nozzle for
proper operation, or restrictions.
Check for excessive starts within a short time
span.
Check oil heater for proper operation.
Check for low oil level, partially closed oil supply
valves, or clogged oil filter.
Check oil cooler refrigerant thermal expansion
valves.
Confirm that TXV (thermostatic expansion valve)
bulb is secured in place and insulated.
Check for sensor wiring and accuracy.
This fault can result from extended operation at low
load with low water flow to the evaporator or
condenser.
Check for high condenser water temperatures, low
water flow, fouled tubes.
Check for division plate/gasket bypass.
Check for noncondensables.
Check transducer wiring and accuracy.
Check for high condenser water temperatures, low
water flow, fouled tubes.
Check for division plate/gasket bypass.
Check for noncondensables.
Check surge prevention parameters in OPTIONS
screen. Increase VFD Increase Step in SETUP2.
Check VFD Minimum Speed in SETUP2 screen.
Spare safety input has tripped or factory installed
jumper is not present on Terminal Block 4 terminals
17 and 20 in the VFD enclosure.
Check for high condenser water temperatures, low
water flow, fouled tubes.
Check for division plate/gasket bypass.
Check for noncondensables.
Check surge prevention parameters in OPTIONS
screen.
Check cooling tower control settings and performance to design/selection temperatures across the
entire operating range of the chiller.
Check cooler approach and water flow.
Check that CCM transducer voltage reference is
between 4.5 v and 5.5 v.
Check that pressure transducers are not shorted to
ground. This fault is normally declared the first time
an ICVC is powered up if it was downloaded with
software when it was not connected to a CCM.
Call Carrier Service.
Check for oil loss or excessive refrigerant. If oil level
is low, refrigerant charge may be too low resulting in
ineffective oil reclaim. Excessive refrigerant charge
may cause liquid carryover into compressor.
Check calibration of evaporator pressure and condenser pressure sensors.
Check calibration of compressor discharge temperature sensor.
Check for high water temperatures or changes in
water flow rates.
Check wiring and control power to CCM.
Confirm that all CCM SW1 switches are in the
“OFF” position.
Check for proper refrigerant charge.
Check float valve operation.
Check for proper fluid flow and temperature.
Confirm that condenser water enters bottom row
of condenser tubes first.
Check Evaporator Refrigerant Temperature
sensor.
Check for division plate gasket bypass.
Check for fouled tubes.
Condenser water too cold or chiller shut down with
brine below 32 F in cooler so equalization temperature in chiller approached 32 F.
Check condenser pressure transducer.
Check refrigerant charge.
*[LIMIT] is shown on the ICVC as the temperature, pressure, voltage, etc., set point predefined or selected by the operator as an override, alert, or
alarm condition. [VALUE] is the actual pressure, temperature, voltage, etc., at which the control tripped.
17
Table 5 — ICVC Alarm Codes (cont)
CHILLER PROTECTIVE LIMIT FAULTS (cont)
ICVC FAULT
PRIMARY
SECONDARY
STATE
MESSAGE
MESSAGE
245
PROTECTIVE LIMIT HIGH VFD SPEED
PRIMARY CAUSE
ADDITIONAL CAUSE/REMEDY
245Actual VFD Speed
exceeded limit of Target VFD
Speed + 10%.
246Diffuser Control Invalid
Configuration: Check SETUP2
Entries.
247Diffuser Position Fault:
Check Guide Vane/Diffuser
Actuator.
Actual VFD Speed on COMPRESS screen must
not exceed Target VFD Speed by more than
10%.
Check 25%, 50%, and 75% Guide Vane and Diffuser Load Point entries in SETUP2 screen.
246
PROTECTIVE LIMIT INVALID DIFFUSER
CONFIG.
247
PROTECTIVE LIMIT DIFFUSER POSITION
FAULT
248
PROTECTIVE LIMIT SPARE TEMPERATURE
#1
249
PROTECTIVE LIMIT SPARE TEMPERATURE
#2
250
251
UNUSED
UNUSED
PROTECTIVE LIMIT VFD CONFIG CONFLICT
252
PROTECTIVE LIMIT VFD CONFIG CONFLICT
253
PROTECTIVE LIMIT GUIDE VANE
CALIBRATION
254
PROTECTIVE LIMIT VFD CHECKSUM ERROR 254Checksum Error:
Press Reset to Restore
Configuration
PROTECTIVE LIMIT VFD DEW PREVENTION 255Dew Prevention - Cool- VFD COLDPLATE TEMP is too close to dew
ant Too Cold. Check Solenoid point based on VFD ENCLOSURE TEMP and
& Cond T.
RELATIVE HUMIDITY in POWER screen.
Check for moisture in VFD enclosure.
Check Humidity Sensor in CONTROLS TEST.
Check for contamination on CCM J3-7 and J3-9
Humidity Sensor.
Check that VFD refrigerant cooling modulating
valve is closing.
PROTECTIVE LIMIT INDUCTOR OVERTEMP
256Inductor Overtemp Trip - Check for cooling fan air flow obstructions.
Check Temp Switch and Cooling Fans.
PROTECTIVE LIMIT VFD START INHIBIT
257VFD Start Inhibit: Check The VFD Start Inhibit is derived from the Alarm
VFD Diagnostic Parameters
bit being set in the VFD. The conditions causing
212/214.
the alarm must be corrected in the VFD to
enable subsequent starts and operation. See
VFD parameters 212/214.
UNUSED STATE
UNUSED
258Unused.
255
256
257
258
248Spare Temperature #1
[VALUE] exceeded limit of
[LIMIT]*.
249Spare Temperature #2
[VALUE] exceeded limit of
[LIMIT]*.
250Unused State.
251VFD Config Conflict
(VFD Uploaded): Verify to
Reset Alarm.
252VFD Config Conflict
(VFD Downloaded): Verify to
Reset Alarm.
253Guide Vane Fault
[VALUE]. Check Calibration.
Confirm that Diffuser Option in SETUP 2 screen
has not been Enabled if compressor does not
have a split ring diffuser. May indicate rotating
stall condition.
Check rotating stall transducer wiring accuracy
and sealing.
Check diffuser schedule and guide vane schedule in SETUP2 screen.
Check for proper operation of diffuser and inlet
guide vane actuators including inlet guide vane
calibration.
Check diffuser actuator coupling for rotational
slip.
Check RC snubber on CCM J4-23 and J4-24.
Check 4.3k ohm resistor between CCM terminals J3-7 and J3-8.
Check for electrical noise in CCM Diffuser Pressure wiring. Do not continue to operate compressor except for diagnostic purposes.
Check Spare Temperature Enable and Spare
Temperature Limit in SETUP1 Screen.
Check Spare Temperature Enable and Spare
Temperature Limit in SETUP1 Screen.
The VFD_CONF table in the Gateway does not
match that which is in the ICVC. This is a normal
fault if an ICVC has been uploaded with software when it was not attached to the CCM.
Enter VFD_CONF screen and then exit
VFD_CONF screen by pressing EXIT then
CANCEL. Re-enter the VFD_CONF screen,
press EXIT then SAVE. Parameters stored in
the Gateway will be uploaded into the ICVC.
Confirm valid settings in VFD_CONF screen.
The VFD_CONF table in the Gateway does not
match that which is in the ICVC.
Enter CONTROL TEST and execute Guide
Vane Calibration.
Check CCM guide vane feedback terminals J4-9
and J4-10.
Check guide vane feedback potentiometer.
Alarm before start indicates guide vane opening
is not less than 4%. Alarm running indicates
guide vane position is < -1% or > 103%, or feedback voltage is < .045 or > 3.15 VDC.
Actual VFD checksum does not match calculated value.
*[LIMIT] is shown on the ICVC as the temperature, pressure, voltage, etc., set point predefined or selected by the operator as an override, alert, or
alarm condition. [VALUE] is the actual pressure, temperature, voltage, etc., at which the control tripped.
18
Table 5 — ICVC Alarm Codes (cont)
CHILLER PROTECTIVE LIMIT FAULTS (cont)
ICVC FAULT
PRIMARY
SECONDARY
STATE
MESSAGE
MESSAGE
259
PROTECTIVE LIMIT CCN OVERRIDE STOP
PRIMARY CAUSE
259CCN Emergency/
Override Stop.
282
PROTECTIVE LIMIT INVALID VFD CONFIG
282Line Frequency
[VALUE] Exceeded Configuration Range.
283
PROTECTIVE LIMIT INVALID VFD CONFIG
283Compressor 100%
Speed Config Ranges: 50=Hz
45-52; 60 Hz=55-62.
284
VFD GATEWAY
COMPATIBILITY
CONFLICT
285
VFD GATEWAY
COMPATIBILITY
CONFLICT
286
PROTECTIVE LIMIT INVERTER
OVERCURRENT
284VFD Gateway Compatibility Conflict: Check VFG/
VFD Versions.
285VFD Gateway Compatibility Conflict: Check VFG/
ICVC Versions.
286Inverter Overcurrent
Fault: Check VFD Status.
ADDITIONAL CAUSE/REMEDY
CCN has signaled the chiller to stop.This fault
must be manually reset from the default screen
of the ICVC.
LINE FREQUENCY in POWER screen must be
maintained between 45-52 Hz if LINE
FREQ=60Hz? is set to NO(50 Hz). LINE FREQUENCY must be maintained between
55-62 Hz if LINE FREQ=60Hz? is set to YES
(60 Hz).
Check high pressure switch and connections to
TB4-24 and TB4-25.
COMPRESSOR 100% SPEED in VFD_CONF
screen must be set between 45-52 Hz if LINE
FREQ=60Hz? is set to NO(50 Hz). COMPRESSOR 100% SPEED must be set between
55-62 Hz if LINE FREQ=60Hz? is set to YES
(60 Hz).
VFD Gateway and VFD software versions are
not compatible.
Call Carrier Service.
VFD Gateway and ICVC software versions are
not compatible.
Call Carrier Service.
Check for high entering water temperature or
low condenser water flow.
Check current settings in VFD_CONF screen.
*[LIMIT] is shown on the ICVC as the temperature, pressure, voltage, etc., set point predefined or selected by the operator as an override, alert, or
alarm condition. [VALUE] is the actual pressure, temperature, voltage, etc., at which the control tripped.
OUT-OF-RANGE SENSOR
ICVC FAULT
STATE
260
PRIMARY
MESSAGE
SENSOR FAULT
261
SENSOR FAULT
262
SENSOR FAULT
263
SENSOR FAULT
264
SENSOR FAULT
265
SENSOR FAULT
266
SENSOR FAULT
267
SENSOR FAULT
268
SENSOR FAULT
269
SENSOR FAULT
270
SENSOR FAULT
271
SENSOR FAULT
SECONDARY
PRIMARY CAUSE
MESSAGE
LEAVING CHILLED WATER 260Sensor Fault: Check
Leaving Chilled Water Sensor.
ADDITIONAL CAUSE/REMEDY
Check sensor resistance or voltage drop.
Check for proper wiring.
Check for disconnected or shorted wiring.
ENTERING CHILLED
261Sensor Fault: Check
Check sensor resistance or voltage drop.
WATER
Entering Chilled Water
Check for proper wiring.
Sensor.
Check for disconnected or shorted wiring.
CONDENSER PRESSURE 262Sensor Fault: Check
Check sensor wiring.
Condenser Pressure Sensor.
Check for disconnected or shorted wiring.
Check for condensation in transducer
connector.
EVAPORATOR
263Sensor Fault: Check
Check sensor wiring.
PRESSURE
Evaporator Pressure Sensor.
Check for disconnected or shorted wiring.
Check for condensation in transducer
connector.
COMPRESSOR BEARING 264Sensor Fault: Check
Check sensor resistance or voltage drop.
TEMP
Comp Thrust Brg Temp Sensor. Check for proper wiring.
Check for disconnected or shorted wiring.
COMPRESSOR MOTOR
265Sensor Fault: Check
Check sensor resistance or voltage drop.
TEMP
Comp Motor Winding Temp
Check for proper wiring.
Sensor.
Check for disconnected or shorted wiring.
COMP DISCHARGE TEMP 266Sensor Fault: Check
Check sensor resistance or voltage drop.
Comp Discharge Temp Sensor. Check for proper wiring.
Check for disconnected or shorted wiring.
OIL SUMP TEMP
267Sensor Fault: Check Oil
Check sensor resistance or voltage drop.
Sump Temp Sensor.
Check for proper wiring.
Check for disconnected or shorted wiring.
COMP OIL PRESS DIFF
268Sensor Fault: Check Oil
Check sensor resistance or voltage drop.
Pump Delta P Sensor.
Check for proper wiring.
Check for disconnected or shorted wiring.
CHILLED WATER FLOW
269Sensor Fault: Check
Check sensor wiring and accuracy.
Chilled Water Delta P Sensor.
Check for disconnected or shorted wiring.
If pressure transducers are not installed,
check for presence of resistors and jumpers
on lower CCM terminal block J3.
COND WATER FLOW
270Sensor Fault: Check
Check sensor wiring and accuracy.
Cond Water Delta P Sensor.
Check for disconnected or shorted wiring.
If pressure transducers are not installed,
check for presence of resistors and jumpers
on lower CCM terminal block J3.
EVAP SATURATION TEMP 271Sensor Fault: Check
Check sensor resistance or voltage drop.
Evap Saturation Temp Sensor. Check for proper wiring.
Check for disconnected or shorted wiring.
19
Table 6 — Powerflex 755 Fault Code Descriptions and Corrective Actions
VFD
FAULT
CODE
ON VFD
HIST
SCREEN
NONE
0
ICVC
FAULT
STATE
FAULT TYPE
206
DESCRIPTION
Processor memory fault
CORRECTIVE ACTION
Consult VFD manual to resolve generic fault.
No Entry
2
207
Auxiliary Input
Input is open.
3
210
Power Loss
Line voltage dropout
4
215
Undervoltage
Low DC bus voltage
5
166
Overvoltage
High DC bus voltage
7
217
Motor Overload
An internal electronic overload trip has occurred.
8
219
Heat Sink Overtemp
Heat sink temperature has exceeded the maximum operating temperature
9
219
Transistor Overtemp
The output transistors have exceeded the maximum operating temperature
12
286
HW Overcurrent
The drive output current has exceeded the hardware current limit.
13
220
Ground Fault
A current path to earth ground greater than 25%
of drive rating has occurred.
14
206
Ground Warning
The ground current has exceeded the level set in
P467
15
206
Load Loss
17
216
20
206
The DC bus ripple
has exceeded a
preset level.
TorqPrv Spd Band
21
225
Output PhaseLoss
24
204
Decel Inhibit
33
206
AuRsts Exhausted
36
286
SW Overcurrent
Check Compressor Discharge High Pressure
switch wiring and accuracy.
Check for high condenser water temperatures,
low water flow, fouled tubes.
Check for division plate/gasket bypass. Check for
noncondensables in refrigerant.
Temporary loss of voltage. Disable Single Cycle
Dropout in VFD_CONF sceen.
Verify phase-to-phase and phase-to-ground line
voltage. VFD Circuit Board malfunction.
Call Carrier Service.
Verify phase to phase and phase to ground line
voltage. Monitor AC line for high transient voltage
conditions.
Any phase current > 106% RLA. Can result from
significant load side current imbalance when
running at full load.
Check entering condenser water temperature
and water flow rate.
Check Motor Rated Load Amps in VFD_CONF
screen.
Check that VFD refrigerant isolation valves are
open.
Check VFD refrigerant cooling orifice and refrigerant strainer.
Check for proper VFD cooling fan operation and
air flow blockage.
Check that VFD refrigerant isolation valves are
open.
Check VFD refrigerant cooling orifice and refrigerant strainer.
Check for proper VFD cooling fan operation and
air flow blockage.
Check for high entering water temperature or low
condenser water flow. Check current settings in
VFD_CONF screen.
Check the motor, motor terminals, and external
wiring to the drive output terminals for a
grounded condition.
—
To reset the processor, cycle power to chiller,
check ICVC VFD_CONF settings and save settings when exiting VFD_CONF screen.
Check VFD parameters with Drive Explorer.
Check phase-to-phase and phase-to-ground disLine Voltage imbalance
tribution bus voltage. Increase Line Voltage %
Imbalance in VFD_CONF screen.
See VFD Fault Code 15
See VFD Fault Code 15
The current in one or more phases has been lost Check Motor Current % Imbalance in
or remains below a preset level.
VFD_CONF screen.
Verify input voltage is within drive specified limits.
Verify system ground impedance follows proper
The drive is not following a commanded deceleration because it is attempting to limit the bus volt- grounding techniques.
Disable bus regulation P186 and/or add dynamic
age.
brake resistor and/or extend deceleration time
P537 and P538.
See VFD Fault Code 15
See VFD Fault Code 15
The drive output current has exceeded the 1 ms Check for excess load, improper DC boost setcurrent rating.
ting, DC brake volts set too high.
If this fault appears, there may be a problem with
software configuration.
20
Table 6 — Powerflex 755 Fault Code Descriptions and Corrective Actions (cont)
VFD
FAULT
CODE
ON VFD
HIST
SCREEN
38
39
ICVC
FAULT
STATE
220
40
41
42
FAULT TYPE
Phase U to Gnd
Phase V to Gnd
DESCRIPTION
Check the wiring between the drive and the
motor.
Check motor for grounded phase.
Check Motor terminals. d. Replace drive.
Check the wiring between the drive and the
motor.
Check Motor terminals.
Replace drive.
GROUND FAULT
Phase W to Gnd
246
43
Phase UV Short
Phase VW Short
CORRECTIVE ACTION
GROUND FAULT
Phase WU Short
44
206
Phase UNot
45
206
46
206
Phase VNot ToGnd GROUND FAULT (no LF2 equivalent)
Phase WNot
55
NONE
61
62
206
206
Shear Pin 1
Shear Pin 2
The temperature sensor on the main control
board detected excessive heat.
See VFD Fault Code 15
See VFD Fault Code 15
64
206
Drive Overload
Drive is overloaded
65
77
206
206
See VFD Fault Code 15
See VFD Fault Code 15
78
206
OW TrqLvlTimeout
IR Volts Range
FluxAmpsRef
Rang
Check that VFD refrigerant isolation valves are
open.Check VFD refrigerant strainer
See VFD Fault Code 15
See VFD Fault Code 15
Check for high entering water temperature or low
condenser water flow. Check current settings in
VFD_CONF screen.
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
79
206
Excessive Load
80
206
AutoTune Aborted
Inverter Overtemp
Motor did not come up to speed in the allotted
time
See VFD Fault Code 15
Ixo voltae calculated from motor nameplate data
is too high.
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
87
206
IXo VoltageRange
91
93
94
95
96
97
206
206
206
206
206
206
Pri VelFdbk Loss
HW Enable Check
Alt VelFdbk Loss
Aux VelFdbk Loss
PositionFdbkLoss
Auto Tach Switch
100
206
The checksum read from the board does not
Parameter Chksum match the checksum calculated.
107
NONE
113
206
Tracking DataErr
Internal data error.
124
141
142
143
144
145
206
206
206
206
206
206
App ID Changed
Autn Enc Angle
Autn Spd Rstrct
Autotune CurReg
Autotune Inertia
Autotune Travel
Application firmware changed.
P78 [Encdrlss AngComp] is out of range
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
The main control board was moved to a different
Replaced MCB-PB power structure. Data set to default values.
21
Check the wiring between the drive and the
motor.
Check Motor terminals.
Replace drive.
Check that guide vanes are closed completely.
Check for high entering water temperature or low
condenser flow.
Repeat Autotune
See VFD Fault Code 15
Re-enter motor nameplate data in VFD_CONF
screen.
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
Press ICVC reset.
Check VFD_CONF parameters.
Cycle power to the drive.
Press ICVC reset.
Check VFD_CONF parameters.
Cycle power to the drive.
Press ICVC reset.
Cycle power to the drive
Verify application version.
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
Table 6 — Powerflex 755 Fault Code Descriptions and Corrective Actions (cont)
VFD
FAULT
CODE
ON VFD
HIST
SCREEN
ICVC
FAULT
STATE
168
206
210
206
211
213
291
292
293
294
295
296
315
316
206
206
206
206
206
206
206
206
206
206
FAULT TYPE
HeatSinkUnderTmp
HW En Jumper
Out
Safety Brd Fault
Safety Jumper In
HSFan Lifwe
InFan Life
MtrBrg Life
MtrBrg Lube
MachBrg life
MachBrg Lube
Excess Psn Error
Node Fault Error
DESCRIPTION
CORRECTIVE ACTION
Heatsink temperature sensor is reporting a value
below -18.7 C (-1.66 F) or the sensor feedback
circuit is open.
Check heat sink temperature sensor. Check heat
sink temperature.
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
See VFD Fault Code 15
Checking Power Modules and Motor Input
with Input Power Off — Use the following procedure
Table 7 — Diode Checks
METER LEAD
METER READING
(+)
(-)
R
DC+
0.5 V
S
DC+
0.5 V
T
DC+
0.5 V
R
DCinfinite (OL)
S
DCInfinite (OL)
T
DCInfinite (OL)
U
DC+
0.5 V
V
DC+
0.5 V
W
DC+
0.5 V
U
DCinfinite (OL)
V
DCInfinite (OL)
W
DCInfinite (OL)
DC+
R
Infinite (OL)
DC+
S
Infinite (OL)
DC+
T
Infinite (OL)
DCR
0.5 V
DCS
0.5 V
DCT
0.5 V
DC+
U
Infinite (OL)
DC+
V
Infinite (OL)
DC+
W
Infinite (OL)
DCU
0.5 V
DCV
0.5 V
DCW
0.5 V
NOTE: Digital meters require a special diode check function
because the current sourced by the meter during a normal resistance (Ohms) test is too low to accurately test a diode. Make sure
the meter is set to the diode test function. Voltage readings may not
be exact as shown in above tables, but look for consistency during
each of the 4 tests. When performing a test that should return infinity
(OL) as shown in above tables, you may see a value slowly climbing
toward infinity. This is a result of the meter charging a capacitor and
is normal.
to check the drive’s power module circuitry with power off:
1. Turn off and lock out input power. Wait five minutes.
2. Verify there is no voltage at the drive’s input power terminals.
3. Using a voltmeter, check the DC bus potential as described above to ensure the DC bus capacitors are discharged.
4. Disconnect the motor from the drive.
5. Check all AC line and DC bus fuses.
6. Use a multimeter to check the input diodes and output
IGBTs if a fuse is open.
7. Check motor impedance.
8. Reconnect the motor to the drive.
9. Reapply input power. See Tables 7 and 8.
WARNING
Confirm that the DC bus has discharged before performing
diode checks.
22
Servicing the Drive
1
WARNING
L1
L2
L3
I
LOCKOUT/TAGOUT
To guard against possible personal injury and/or equipment
damage:
1. Inspect all lifting hardware for proper attachment before lifting drive.
2. Do not allow any part of the drive or lifting mechanism to make contact with electrically charged conductors or components.
3. Do not subject the drive to high rates of acceleration
or deceleration while transporting to the mounting location or when lifting.
Do not allow personnel or their limbs directly underneath
the drive when it is being lifted and mounted.
O
2
DC BUS TEST
TERMINALS
LOCATED INSIDE
ACCESS DOOR
A19-1814 Fig.
DC+ DC–
0V
0V
MULTIMETER
17 — Check DC Bus Terminals
WARNING
DC bus capacitors retain hazardous voltages after input
power has been disconnected. After disconnecting input
power, wait five (5) minutes for the DC bus capacitors to
discharge and then check the voltage with a voltmeter to
ensure the DC bus capacitors are discharged before touching any internal components. Failure to observe this precaution could result in severe bodily injury or loss of life.
SLIDE
ENCLOSURE
FORWARD
LOOSEN
ENCLOSURE
FASTENERS
1. Using recommended screwdriver = 6.4 mm (0.25 in.) flat
or T20 star, open access door. See Fig. 16.
2. Check to be sure that the voltage between DC+ and DCand from each DC terminal to the chassis is zero before
proceeding. See Fig. 17.
3. Remove the enclosure. See Fig. 18.
REMOVING THE DRIVE — The dimensions and weights
specified must be taken into consideration when removing the
drive. All lifting equipment and lifting components (hooks,
bolts, lifts, slings, chains, etc.) must be properly sized and rated
to safely lift and hold the weight of the drive while removing it.
See Fig. 19. The drive weights are as follows:
• Drive weight for Frame 6: 85 lb.
• Drive weight for Frame 7: 160 - 249 lb.
90°
A19-1816
Fig. 18 — Removing Enclosure
When replacing the drive, reverse the procedures and tighten to the torques for the Frames 6 and 7 Power Terminal Block
referred to in Table 8.
Table 8 — Frames 6 and 7 Power Terminal Block
FRAME
6
7
MAXIMUM LUG
RECOMMENDED
WIDTH
TORQUE
34.6 mm (1.36 in.) 11.3 N·m (100 in.-lb)
43.5 mm (1.71 in.) 11.3 N·m (100 in.-lb)
TERMINAL
BOLT SIZE
M8 x 1.25
M8 x 1.25
RIGGING THE ENCLOSURE — Where overhead room
and/or clearance in front of the drive enclosure is insufficient to
allow the drive to be safely removed from the enclosure, the
entire enclosure may have to be removed from the chiller.
The dimensions and weights specified must be taken into
consideration when removing the enclosure. The total weight
for Frames 6 and 7, including drive weight and enclosure, is
720 lb. All lifting equipment and lifting components (hooks,
bolts, lifts, slings, chains, etc.) must be properly sized and rated
to safely lift and hold the weight of the enclosure and drive
while removing. See Fig. 20A and Fig. 20B.
A19-1831 Fig. 16 — Open Access Door
23
DRIVE RIGGING ACCESS
DRIVE WIDTH + 4 IN.
<45°
>1/2 A
A
Fig. 20A — Rigging the Enclosure, Frame 6
A19-1837
<45°
>1/2 A
A
FRONT VIEW
2 IN.
Fig. 20B — Rigging the Enclosure, Frame 7
A19-1838
2 IN.
DRIVE RIGGING
ACCESS
REPLACING THE GATEWAY (A-B20-750-20COMM
OPTION CARD) — The following are the steps for removing and replacing the existing gateway.
1. Disconnect power to the drive. Before removing the enclosure, open the access door on the front of the drive.
See Fig. 16.
2. Check to be sure that the voltage between DC+ and DCand from each DC terminal to the chassis is zero before
proceeding. See Fig. 17.
3. Remove the enclosure. See Fig. 18.
4. Remove the 2 screws securing the mounting plate and remove the mounting plate and COMM card. See Fig. 21.
5. Mount the new COMM card and mounting plate and attach with the 2 screws removed in Step 4. See Fig. 22.
6. Use the shorter ribbon cable to connect the plug on the
COMM card to the connector on the mounting plate. See
Fig. 21.
7. Install the enclosure. See Fig. 18.
DRIVE POSITIONED FOR
VERTICAL LIFT
DRIVE EXTENDS
BEHIND MAIN
ENCLOSURE
SUPPORT FROM
BELOW
SIDE VIEW
Fig. 19 — Enclosure Access for Removing Drive
a19-1817
A19-1818
24
GATEWAY
MOUNTING PLATE
0.45-0.67 N-m
(4.0-6.0 lb.-in.)
3 PLACES
RIBBON CABLE
 CHILL PLATE FAN AND INTERNAL FAN REPLACEMENT — The following are the steps to replace the chill plate
fan and internal fan in Frames 6 and 7.
Frame 6:
1. Disconnect power to the drive. Before removing the enclosure, open the access door on the front of the drive.
See Fig. 16.
2. Check to be sure that the voltage between DC+ and DCand from each DC terminal to the chassis is zero before
proceeding. See Fig. 17.
3. Remove the enclosure. See Fig. 18.
4. Remove and replace the chill plate fan. See Fig. 23.
5. Remove and replace the internal fan. See Fig. 24.
6. Install the enclosure. See Fig. 18.
CHILL PLATE
FAN POWER
CONNECTION
Fig. 21 — COMM Card
A19-1819
CHILL PLATE FAN
MOUNTING PLATE
GATEWAY
T20
2.6 N•m (23 lb•in.)
Fig. 23 — Chill Plate Fan, Frame 6
A19-1839
2.6 N•m
(23 lb•in.)
T20
INTERNAL FAN
Fig. 22 — Mount COMM Card Plate to Drive
A19-1820
T20
2.6 N•m
(23 lb•in.)
A19-1840
Fig. 24 — Internal Fan, Frame 6
25
711
Frame 7:
1. Disconnect power to the drive. Before removing the enclosure, open the access door on the front of the drive.
See Fig. 16.
2. Check to be sure that the voltage between DC+ and DCand from each DC terminal to the chassis is zero before
proceeding. See Fig. 17.
3. Remove the enclosure. See Fig. 18.
4. Remove and replace the Heat Sink and Internal and fans.
See Fig. 25.
Install the enclosure. See Fig. 18.
5.20 N•m
(46 lb•in.)
T15
INTERNAL FANS
T15
2.6 N•m (23 lb•in.)
Part Identification and Location — See Fig. 26-28
X2
for parts descriptions and locations.
T20
CHILL PLATE FANS
2.6 N•m (23 lb•in.)
Fig. 25 — Chill Plate and Internal Fans, Removal
and Replacement, Frame 7 A19-1841
CR6
1
2
CABLE
ACCESS
CUTOUT
TB1,TB2,
FU1-FU3
1
TB4
DIST.
SIDE FU2
TB1 TB2 FU1 FU3
CB2
1
1
CB
TB4
CR1
CR2
CR3
CR4
CR5
CR6
1
3P
KTK/FNQ-R
30A
PT1
4
3
2
SECONDARY
SIDE
TOWARD
DOOR
2
2
PT1
5
SECONDARY SIDE
LEFT SIDEWALL
VIEW FROM INSIDE
FRONT VIEW
DOOR REMOVED
80
1
2
3
4
5
6
—
—
—
—
—
—
LEGEND
Power Module
Input Circuit Breaker
15 Amp Control Circuit Breaker
Control Transformer
Control Fuses
Control Relays (CR1 - CR5)
Fig. 26 — Assembly Parts
26
a19-1847
876 5 876 5 876 5 876 5 876 5 876 5
4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
LINECB1 PE
876 5 876 5 876 5 876 5 876 5 876 5
4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
14
13 14
13 14
13 14
13 14
13 14
13
12 1110 9 12 1110 9 12 1110 9 12 1110 9 12 1110 9 12 1110 9
CR 1
14
13 14
13 14
13 14
13 14
13 14
13
12 1110 9 12 1110 9 12 1110 9 12 1110 9 12 1110 9 12 1110 9
6
EA1
CR1
CR2
CR3
CR4
CR5
CR6
TB4
a19-1848
NOTE: When replacing the Main Control Board (Item No. 1) the jumper marked
“J1 ENABLE” must be removed and the jumper marked “J1 SAFETY” must be
left in place.
1
2
3
4
5
6
7
8
LEGEND
PF750 Series, Precharge Kit
PF750 Series, Gate Interface
PF750 Series, Power Interface
PowerFlex 750 Series, Flange Gasket
PF755 Main Control Board
PF750 Series, Backplane Interface
PF750 Series, Type 4X/12 Chill Plate
(Heatsink) Fan Kit
— Chill Plate Fan
—
—
—
—
—
—
—
Fig. 27 — Frame 6 Parts
1
2
3
4
5
6
7
8
9
10
—
—
—
—
—
—
—
—
—
—
LEGEND
Slot for Gateway (Gateway Not Shown)
PF750 Series, Backplane Interface
PF750 Series, Type 4X/12 Heatsink Fan Kit
PF750 Series, Power Interface
PF750 Series, Bus Cap Assembly
PF750 Series, Power Interface Cable
PF750 Series, Current Transducer Kit
PF750 Series, Precharge Kit
Slot for 24V I/O Module (24V I/O Module Not Shown)
PF755 Main Control Board
NOTE: When replacing the Main Control Board (Item No. 1) the jumper marked “J1 ENABLE” must be
removed and the jumper marked “J1 SAFETY” must be left in place.
Fig. 28 — Frame 7 Parts
27
a19-1849
APPENDIX A — WIRING SCHEMATICS
CHILLER CONTROL SCHEMATIC
(SHIELD)
AUTO DEMAND LIMIT
(OPTIONAL)
EXT
4-20mA
(1-5vdc)
AUTO CHILLED WATER
RESET (OPTIONAL)
EXT
4-20mA
(1-5vdc)
(RED)
(BLK)
(CLR)
(CLR)
(BLK)
(SHIELD)
4-20mAkw
OUTPUT
6
+
-
+
-
+
+
-
2
3
5
4
3
2
J5
2
(RED)
3
(BLK)
4
COND ENT
WATER TEMP
(RED)
5
(BLK)
6
COND LVG
WATER TEMP
(RED)
7
(BLK)
8
4
8
7
10K
(CLR)
9
(BLK)
10
4
3
+
2
1
1
J6
J7
J8
SWITCH POSITION
O
N
1 2 3
SW "ON" = EXT 4-20mA
SW "OFF" = EXT 1-5Vdc
SW2
(WHT)
1 "OFF"
2 "ON"
(BLU)
REMOTE TEMP
RESET
(OPTIONAL)
L2
DIFFUSER ACTUATOR
(RED)
11
(BLK)
12
(WHT)
13
(BLK)
14
(BLK)
(SHIELD)
3
(CLR)
2
(RED)
1
(BLK)
(WHT)
COMMON
X
G.V. INCREASE
3
G.V. DECREASE
2
L1
15
L2
16
2
3
COMP'R OIL
SUMP TEMP
1
2
3
NOISE
SUPPRESSOR
17
(BLK)
18
(CLR)
19
(BLK)
20
(RED)
(BLK)
(YEL)
(CLR)
CB2
(SPARE)
(RED)
21
(BLK)
22
(CLR)
23
(BLK)
24
6
(BLK)
5
(BRN)
4
(BLU)
3
(BLK)
2
(WHT)
26
(WHT)
27
(BLK)
28
(BLK)
1
(CLR)
2
(RED)
3
(BLK)
4
(CLR)
5
(RED)
(BLK)
6
+
+
7
LOAD RESISTOR
8
4.3K
S
+
1C
(ORN)
9
(RED)
(WHT)
COMP'R OIL PUMP
(RED)
(BRN)
COMP'R OIL HEATER
(GRY)
(BRN)
(WHT)
CCM
+
100»f
+
NOTE: GND SHIELDS AT THIS END ONLY
100»f
(SHIELD)
J3 (UPPER)
(BLK)
C1
2C
C1
25
SPARE TEMP #2
(OPTIONAL)
-
(WHT)
(BRN)
(WHT)
RMS
(BRN)
HGBP (OPTIONAL)
(BRN)
C2
SPARE TEMP #1
(OPTIONAL)
RELATIVE
HUMIDITY
*
1
3C
(SPARE)
1
OIL PUMP
DISCH PRESS
VFD COOLANT
SOLENOID
(CLR)
(BLK)
C2
OIL SUMP
PRESS
(BLK)
(BLK)
3
J12
1
GUIDE VANE ACTUATOR
J4 (LOWER)
(RED)
COMP'R
DISCH TEMP
COMP'R
MOTOR TEMP
(YEL)
L1
(SHIELD)
EVAP REFRIG
LIQUID TEMP
COMP'R THRUST
BRG TEMP
(BLK)
(ORN)
3 "ON"
J11
G.V. POSITION
FEEDBACK
1
-
J10
(BLK)
EVAP LVG
WATER TEMP
J4 (UPPER)
EVAP ENT
WATER TEMP
1
+
J9
6
(RED)
-
(SHIELD)
(RED)
+
(RED)
(CLR)
G
(WHT)
(BLK)
-
(BLK)
(WHT)
10
SP
11
LOAD RESISTOR
ALL SWITCHES SET
TO "OFF" POSITION
12
(RED)
1
(GRY)
2
10K
14
LOAD RESISTOR
17
18
19
20
J3 (LOWER)
16
JUMPER
0
N
SW1
15
4.3K
1 2 3 4 5 6 7 8
13
R
2
(RED)
J1
21
22
CB1
1
(GRY)
(GRY)
23
JUMPER
(RED)
5
ICVC
24VAC
(GRY)
4
(BLK)
3
-
(CLR)
2
G
1
+
(RED)
(GRY)
24
ALARM
J1
LOAD RESISTOR
4.3K
J7
6
STOP
J8
1
(CLR)
2
(RED)
3
(BLK)
4
+
-
COND PRESS
(CLR)
5
(RED)
6
+
SERVICE
J2
(BLK)
-
EVAP PRESS
a19-1946
28
CCN
APPENDIX A — WIRING SCHEMATICS (cont)
CHILLER CONTROL SCHEMATIC (cont)
(GRN)
1
TO TB-G **
21
COMP'R OIL HEATER
11
11
230V
1C
22
(BLK)
(WHT)
6
(WHT)
13
(WHT)
(RED)
(WHT)
(WHT)
1C
OPEN
HGBP
ACTUATOR
1C
13
COM
(WHT)
12
(BLK)
1C
23
COM
3
5
1C
(BLK)
12
115V
2
4 CLOSE
(BLK)
(BLK)
(BLK)
3C
6
(WHT)
1C
5
230V WIRING MODIFICATION
COMP'R OIL HEATER
(BLU)
(BLK)
3C
(BLK)
(BLU)
4
2
(WHT)
(WHT)
HOT GAS BYPASS
(BLK)
(BLK)
(FR #7 & 8 HT EXCH)
115V CONTROL ONLY
(BLK)
(RED)
(YEL)
(RED)
51
(ORN)
50
(BRN)
43
(BLK)
(BLK)
17
(BLK)
(CLR)
C
(BLK)
B
(RED)
A
(RED)
(WHT)
(BLK)
(BLK)
(BLK)
(WHT)
(WHT)
T1
24VAC
(RED)
(WHT)
(RED)
(WHT)
T3
24VAC
T2
24VAC
(GRN)
TO VFD
(BRN)
(BRN)
(BRN)
(BRN)
(BRN)
(BRN)
(BLU)
COMP'R DISCH
HIGH PRESS
(RED)
(BLU)
(RED)
HGBP
SOLENOID
(YEL)
(BLK)
(SHIELD)
(BLK)
(RED)
(GRY)
(RED)
(BLK)
(GRY)
(BLK)
(YEL)
4
2
(RED)
3C
(BLK)
SHOWN WIRED FOR 115V
(CLR)
(BLK)
(BRN)
23
2
1
21
(GRN)
WHT
WHT
(WHT)
UPC
(WHT)
(BLU)
(RED)
COMP'R OIL PUMP MOTOR
WINDING HIGH TEMPERATURE
(BLU)
(RED)
(WHT)
(YEL)
(RED)
(BLK)
HGBP
SOLENOID
(BLK)
(GRY)
(BLK)
(YEL)
4
2
3C
230V WIRING MODIFICATION
HOT GAS BYPASS
(FR #1 - 6 HT EXCH)
a19-1947
YEL
11
21
(YEL)
VOLTAGE
2C
22
PER JOB
REQM'T
BLK
12
(RED)
2C
CB
CCM
HGBP
ICVC
RHS
UPC
VFD
LEGEND
Circuit Breater
Chiller Control Module
Hot Gas Bypass
International Chiller Visual Controller
Relative Humidity Sensor
Universal Protocol Controller
Variable Frequency Drive
Denotes Control Panel Terminal
Denotes Oil Pump Terminal
Denotes Power Panel Terminal
Denotes Motor Starter Panel Conn
Denotes Component Terminal
Wire Splice
Denotes Conductor male/Female Connector
Option Wiring
**
* Standard on LF2 drive; optional on machines equipped with
other VFDs.
29
COMP'R OIL
PUMP MOTOR
RED
13
23
(1-1/2 HP)
M
(BLK)
2C
APPENDIX A — WIRING SCHEMATICS (cont)
 ROCKWELL POWERFLEX 755 WIRING SCHEMATIC (Typical)
a19-1966
CONTINUED ON
FACING PAGE
NOT
USED
611
30
APPENDIX A — WIRING SCHEMATICS (cont)
 ROCKWELL POWERFLEX 755 WIRING SCHEMATIC (Typical) (cont)
DETAIL A
TB4 34
TB4 33
CARRIER
FACTORY
WIRING
SEE
DETAIL
A
a19-1967
SEE
DETAIL
B
DETAIL B
TB4
35
POWER
PANEL
43
TB4
36
19
CARRIER
FACTORY
WIRING
CAP
CB
COM
COMM
COND
CR
DPI/SI
EA
EMI
EVAP
FU
GND
JMPR
M
NC
NO
PE
POD
REM
ROC
SHLD
TB
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
POWER
PANEL
LEGEND
Capacitor
Circuit Breaker
Common
Communication
Condenser
Control Relay
Internal Communication Protocols Connections
Electrical Assembly
Electro-Magnetic Interference
Evaporator
Fuse
Ground
Jumper
Motor
Normally Closed
Normally Open
Potential Earth (Ground)
I/O Card Mounting Slot Board
Remote
Relay Output Common
Shield
Terminal Block
* Located outside of starter; connected by field wiring.
31
611
APPENDIX B — OPTIONAL BACNET COMMUNICATIONS WIRING
Optional BACnet* Communications Wiring —
6
5
7 8
2 34
5
6
10's
a48-8578
1
9 0
2 34
7 8
9 0
1
The following section is used to configure the UPC Open controller which is used when the BACnet communications option
is selected. The UPC Open controller is mounted in a separate
enclosure below the main control box.
TO ADDRESS THE UPC OPEN CONTROLLER — The
user must give the UPC Open controller an address that is
unique on the BACnet network. Perform the following procedure to assign an address:
1. If the UPC Open controller is powered, pull the screw terminal connector from the controller's power terminals labeled Gnd and HOT. The controller reads the address
each time power is applied to it.
2. Using the rotary switches (see Fig. A and B), set the controller's address. Set the Tens (10's) switch to the tens digit of the address, and set the Ones (1's) switch to the ones
digit.
As an example in Fig. B, if the controller’s address is 25,
point the arrow on the Tens (10's) switch to 2 and the arrow on
the Ones (1's) switch to 5.
1's
Fig. B — Address Rotary Switches
BACNET DEVICE INSTANCE ADDRESS — The UPC
Open controller also has a BACnet Device Instance address.
This Device Instance MUST be unique for the complete BACnet system in which the UPC Open controller is installed. The
Device Instance is auto generated by default and is derived by
adding the MAC address to the end of the Network Number.
The Network Number of a new UPC Open controller is 16101,
but it can be changed using i-Vu® Tools or BACView device.
By default, a MAC address of 20 will result in a Device Instance of 16101 + 20 which would be a Device Instance of
1610120.
BT485
TERMINATOR
BACNET
CONNECTION
(BAS PORT)
POWER LED
Tx1 LED
Rx1 LED
Tx2 LED
Rx2 LED
23
45
01
8
67 9
EIA-485
JUMPERS
01
8
67 9
23
45
BACNET
BAUD RATE
DIP SWITCHES
ADDRESS
ROTARY
SWITCHES
RUN LED
ERROR LED
Fig. A — UPC Open Controller
a48-8579
* Sponsored by ASHRAE (American Society of Heating, Refrigerating and Air Conditioning Engineers).
32
APPENDIX B — OPTIONAL BACNET COMMUNICATIONS WIRING (cont)
CONFIGURING THE BAS PORT FOR BACNET MS/
TP — Use the same baud rate and communication settings for
all controllers on the network segment. The UPC Open controller is fixed at 8 data bits, No Parity, and 1 Stop bit for this
protocol's communications.
If the UPC Open controller has been wired for power, pull
the screw terminal connector from the controller's power terminals labeled Gnd and HOT. The controller reads the DIP
Switches and jumpers each time power is applied to it.
Set the BAS Port DIP switch DS3 to “enable.” Set the BAS
Port DIP switch DS4 to “EIA-485.” Set the BMS Protocol DIP
switches DS8 through DS5 to “MSTP.” See Table A.
8580
Fig. C — DIP Switches
Table A — SW3 Protocol Switch Settings
for MS/TP
DS8
Off
DS7
Off
DS6
Off
DS5
Off
DS4
On
Wire the controllers on an MS/TP network segment in a daisy-chain configuration. Wire specifications for the cable are
22 AWG (American Wire Gage) or 24 AWG, low-capacitance,
twisted, stranded, shielded copper wire. The maximum length
is 2000 ft.
Install a BT485 terminator on the first and last controller on
a network segment to add bias and prevent signal distortions
due to echoing. See Fig. B, D, and E.
To wire the UPC Open controller to the BAS network:
1. Pull the screw terminal connector from the controller's
BAS Port.
2. Check the communications wiring for shorts and
grounds.
3. Connect the communications wiring to the BAS port’s
screw terminals labeled Net +, Net -, and Shield.
NOTE: Use the same polarity throughout the network
segment.
4. Insert the power screw terminal connector into the UPC
Open controller's power terminals if they are not currently connected.
5. Verify communication with the network by viewing a
module status report. To perform a module status report
using the BACview keypad/display unit, press and hold
the “FN” key then press the “.” Key.
DS3
Off
Verify that the EIA-485 jumpers below the CCN Port are set
to EIA-485 and 2W.
The example in Fig. C shows the BAS Port DIP Switches
set for 76.8k (Carrier default) and MS/TP.
Set the BAS Port DIP Switches DS2 and DS1 for the appropriate communications speed of the MS/TP network (9600,
19.2k, 38.4k, or 76.8k bps). See Fig. C and Table B.
Table B — Baud Selection Table
BAUD RATE
9,600
19,200
38,400
76,800
DS2
Off
On
Off
On
a48-
DS1
Off
Off
On
On
WIRING THE UPC OPEN CONTROLLER TO THE MS/
TP NETWORK — The UPC Open controller communicates
using BACnet on an MS/TP network segment communications
at 9600 bps, 19.2 kbps, 38.4 kbps, or 76.8 kbps.
a48-8581
Fig. D — Network Wiring
33
APPENDIX B — OPTIONAL BACNET COMMUNICATIONS WIRING (cont)
a48-8582
Fig. E — BT485 Terminator Installation
temperature rating specifications list two acceptable alternatives. The Halar specification has a higher temperature rating
and a tougher outer jacket than the SmokeGard specification,
and it is appropriate for use in applications where the user is
concerned about abrasion. The Halar jacket is also less likely to
crack in extremely low temperatures.
NOTE: Use the specified type of wire and cable for maximum
signal integrity.
To install a BT485 terminator, push the BT485 terminator
on to the BT485 connector located near the BACnet connector.
NOTE: The BT485 terminator has no polarity associated with
it.
To order a BT485 terminator, consult Commercial Products
i-Vu Open Control System Master Prices.
MS/TP WIRING RECOMMENDATIONS — Recommendations are shown in Tables C and D. The wire jacket and UL
Table C — MS/TP Wiring Recommendations
SPECIFICATION
Cable
Conductor
Insulation
Color Code
Twist Lay
Shielding
Jacket
DC Resistance
Capacitance
Characteristic Impedance
Weight
UL Temperature Rating
Voltage
Listing
AWG
CL2P
DC
FEP
NEC
O.D.
TC
UL
—
—
—
—
—
—
—
—
RECOMMMENDATION
Single twisted pair, low capacitance, CL2P, 22 AWG (7x30), TC foam FEP, plenum rated cable
22 or 24 AWG stranded copper (tin plated)
Foamed FEP 0.015 in. (0.381 mm) wall 0.060 in. (1.524 mm) O.D.
Black/White
2 in. (50.8 mm) lay on pair 6 twists/foot (20 twists/meter) nominal
Aluminum/Mylar shield with 24 AWG TC drain wire
SmokeGard Jacket (SmokeGard PVC) 0.021 in. (0.5334 mm) wall 0.175 in. (4.445 mm) O.D.
Halar Jacket (E-CTFE) 0.010 in. (0.254 mm) wall 0.144 in. (3.6576 mm) O.D.
15.2 Ohms/1000 feet (50 Ohms/km) nominal
12.5 pF/ft (41 pF/meter) nominal conductor to conductor
100 Ohms nominal
12 lb/1000 feet (17.9 kg/km)
SmokeGard 167°F (75°C)
Halar -40 to 302°F (-40 to 150°C)
300 Vac, power limited
UL: NEC CL2P, or better
LEGEND
American Wire Gage
Class 2 Plenum Cable
Direct Current
Fluorinated Ethylene Polymer
National Electrical Code
Outside Diameter
Tinned Copper
Underwriters Laboratories
34
APPENDIX B — OPTIONAL BACNET COMMUNICATIONS WIRING (cont)
Table D — Open System Wiring Specifications and Recommended Vendors
WIRING SPECIFICATIONS
Wire Type
RECOMMENDED VENDORS AND PART NUMBERS
Connect Air
Contractors
Belden RMCORP Wire and Cable
International
Description
22 AWG, single twisted shielded pair, low capacitance, CL2P,
TC foam FEP, plenum rated. See MS/TP Installation Guide for
specifications.
MS/TP
Network (RS-485) 24 AWG, single twisted shielded pair, low capacitance, CL2P,
TC foam FEP, plenum rated. See MS/TP Installation Guide
for specifications.
Rnet
4 conductor, unshielded, CMP, 18 AWG, plenum rated.
AWG
CL2P
CMP
FEP
TC
—
—
—
—
—
W221P-22227
—
25160PV
CLP0520LC
W241P-2000F
82841
25120-OR
—
W184C-2099BLB
6302UE
21450
CLP0442
LEGEND
American Wire Gage
Class 2 Plenum Cable
Communications Plenum Rated
Fluorinated Ethylene Polymer
Tinned Copper
If modifications to the default Element and Bus number are
required, both the ComfortLink and UPC Open configurations
must be changed.
The following configurations are used to set the CCN Address and Bus number in the ComfortLink control. These configurations can be changed using the scrolling marquee display
or accessory Navigator handheld device.
Configuration→CCN→CCN.A (CCN Address)
Configuration→CCN→CCN.B (CCN Bus Number)
The following configurations are used to set the CCN Address and Bus Number in the UPC Open controller. These configurations can be changed using the accessory BACview6 display.
Navigation: BACview→CCN
Home: Element Comm Stat
Element: 1
Bus: 0
TROUBLESHOOTING — If there are problems wiring or
addressing the UPC Open controller, contact Carrier Technical
Support.
LOCAL ACCESS TO THE UPC OPEN CONTROLLER — The user can use a BACview6 handheld keypad display unit or the Virtual BACview software as a local user interface to an Open controller. These items let the user access the
controller network information. These are accessory items and
do not come with the UPC Open controller.
The BACview6 unit connects to the local access port on the
UPC Open controller. See Fig. F. The BACview software must
be running on a laptop computer that is connected to the local
access port on the UPC Open controller. The laptop will require an additional USB link cable for connection.
See the BACview Installation and User Guide for instructions on connecting and using the BACview6 device.
To order a BACview6 Handheld (BV6H), consult Commercial Products i-Vu® Open Control System Master Prices.
CONFIGURING THE UPC OPEN CONTROLLER'S
PROPERTIES — The UPC Open device and ComfortLink™
controls must be set to the same CCN Address (Element) number and CCN Bus number. The factory default settings for
CCN Element and CCN Bus number are 1 and 0 respectively.
Fig. F — BACview6 Device Connection
35
APPENDIX B — OPTIONAL BACNET COMMUNICATIONS WIRING (cont)
COMMUNICATION LEDS — The LEDs indicate if the
controller is communicating with the devices on the network.
See Tables E and F. The LEDs should reflect communication
traffic based on the baud rate set. The higher the baud rate the
more solid the LEDs become. See Fig. B for location of LEDs
on UPC Open module.
REPLACING THE UPC OPEN BATTERY — The UPC
Open controller's 10-year lithium CR2032 battery provides a
minimum of 10,000 hours of data retention during power
outages.
IMPORTANT: Power must be ON to the UPC Open when
replacing the battery, or the date, time, and trend data will
be lost.
Remove the battery from the controller, making note of the
battery's polarity. Insert the new battery, matching the battery's
polarity with the polarity indicated on the UPC Open
controller.
NETWORK POINTS LIST — The points list for the controller is shown in Table G.
Table E — LED Status Indicators
LED
Power
Rx
Tx
Run
Error
STATUS
Lights when power is being supplied to the controller. The UPC Open controller is protected by internal solid-state polyswitches on
the incoming power and network connections. These polyswitches are not replaceable and will reset themselves if the condition
that caused the fault returns to normal.
Lights when the controller receives data from the network segment; there is an Rx LED for Ports 1 and 2.
Lights when the controller transmits data to the network segment; there is a Tx LED for Ports 1 and 2.
Lights based on controller status. See Table F.
Lights based on controller status. See Table F.
Table F — Run and Error LEDs Controller and Network Status Indication
RUN LED
2 flashes per second
2 flashes per second
2 flashes per second
2 flashes per second
2 flashes per second
5 flashes per second
5 flashes per second
7 flashes per second
14 flashes per second
ERROR LED
Off
2 flashes, alternating with Run LED
3 flashes, then off
1 flash per second
On
On
Off
7 flashes per second, alternating with Run LED
14 flashes per second, alternating with Run LED
36
STATUS
Normal
Five minute auto-restart delay after system error
Controller has just been formatted
Controller is alone on the network
Exec halted after frequent system errors or control programs halted
Exec start-up aborted, Boot is running
Firmware transfer in progress, Boot is running
Ten second recovery period after brownout
Brownout
APPENDIX B — OPTIONAL BACNET COMMUNICATIONS WIRING (cont)

Table G — Network Points List
%
%
%
°F
^F
^F
^F
N/A
°F
N/A
°F
°F
°F
N/A
N/A
PSI
°F
PSI
°F
°F
%
%
%
N/A
DEFAULT
VALUE
N/A
N/A
N/A
N/A
N/A
1.0
N/A
N/A
OFF
N/A
STOP
N/A
N/A
N/A
NO
OFF
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
R
N/A
EMSTOP
R
ECW
ECDW
Equipment Alarm
Evaporator Pressure
Evaporator Refrigerant Temp
Leaving Chilled Water Prime Variable
Leaving Condenser Water
Line Active Current
Line Active Voltage
Line Frequency
Line Power Factor
Local Schedule
Occupied?
Oil Sump Temperature
Remote Start Contact
POINT DESCRIPTION
1st Current Alarm State
Active Demand Limit
Actual Guide Vane Position
Actual VFD Speed
Calc Evap Sat Temp
Chilled Water Deadband
Chilled Water Delta P
Chilled Water Delta T
Chilled Water Pump
Chilled Water Temp
Chiller Start/Stop
Comp Discharge Temp
Comp Motor Winding Temp
Comp Thrust Brg Temp
Cond Water Flow
Cond Water Pump
Condenser Pressure
Condenser Refrig Temp
Condenser Water Delta P
Control Point
Current CHW Setpoint
Demand Level 1
Demand Level 2
Demand Level 3
Element Comm Status
Element Communications
Alarm
Emergency Stop
Entering Chilled Water
Entering Condenser Water
CCN
POINT NAME
ALARM_01
DEM_LIM
GV_POS
VFD_ACT
EAT
CWDB
CHWPD
CHW_DT
CHLP
CHW_TMP
CHIL_S_S
CMPD
MTRW
MTRB
CDW_FLOW
CDP
CRP
CRT
CDWPD
LCW_STPT
CHWSTPT
N/A
N/A
N/A
N/A
READ/
WRITE
R
R/W
R
R
R
R
R
R
R
R
R/W
R
R
R
R
R
R
R
R
R/W
R
R
R
R
R
UNITS
0-270
40 to 100
0 to 100
0 to 110
-40 to 245
0.5 to 2.0
-6.7 to 420
-40 to 245
OFF/ON
-40 to 245
STOP/START
-40 to 245
-40 to 245
-40 to 245
NO/YES
OFF/ON
-6.7 to 420
-40 to 245
-6.7 to 420
10 to 120
0.00 to 99.9
0 to 100
0 to 100
0 to 100
No Comm/Normal
BACNET
OBJECT ID
AV:4
AV:6
AV:7
AV:11
AV:13
AV:14
AV:15
AV:16
BV:4
AV:17
BV:5
AV:18
AV:19
AV:20
BV:6
BV:7
AV:21
AV:22
AV:23
AV:24
AV:25
AV:1
AV:2
AV:3
BV:2999
BACNET
OBJECT NAME
alarm_01_1
dem_lim_1
gv_pos_1
vfd_act_1
ert_1
cwdb_1
chwpd_1
chw_dt_1
chlp_1
chw_tmp_1
chil_s_s_1
cmpd_1
mtrw_1
mtrb_1
cdw_flow_1
cdp_1
crp_1
crt_1
cdwpd_1
lcw_stpt_1
chwstpt_1
dmv_lvl_1_perct_1
dmv_lvl_2_perct_1
dmv_lvl_3_perct_1
element_stat_1
N/A
N/A
Inactive/Active
BV:20
comm_lost_alm_1
N/A
ENABLE
BV:8
emstop_1
R
R
°F
°F
N/A
N/A
AV:26
AV:27
ecw_1
ecdw_1
N/A
R
N/A
N/A
BV:1
element_alarm_1
ERP
ERT
R
R
PSI
°F
N/A
N/A
ENABLE/
EMSTOP
-40 to 245
-40 to 245
Comm Normal
Comm Lost
-6.7 to 420
-40 to 245
AV:28
AV:13
erp_1
ert_1
RANGE
LCW
R
°F
N/A
-40 to 245
AV:31
lcw_1
LCDW
AMPS_ACT
VOLT_ACT
LINEFREQ
LINE_PF
N/A
OCC
OILT
REM_CON
R
R
R
R
R
R
R
R
R/W
°F
A
V
Hz
N/A
N/A
°F
N/A
N/A
N/A
N/A
N/A
N/A
N/A
NO
N/A
OPEN
AV:32
AV:8
AV:9
AV:30
AV:34
BV:2
BV:10
AV:33
BV:11
lcdw_1
amps_act_1
volt_act_1
linefreq_1
line_pf_1
schedule_1
occ_1
oilt_1
rem_con_1
STATUS
R
N/A
N/A
AV:35
status_1
Service Ontime
Surge Line Delta T
S_HRS
DELTA_TX
R/W
R
hr
°F
N/A
N/A
AV:36
AV:38
s_hrs_1
delta_tx_1
System Alert/Alarm
SYS_ALM
R
N/A
N/A
-40 to 245
0.0 to 99999.0
0.0 to 99999.0
0 to 99
0.00 to 2.00
No Comm/Normal
NO/YES
-40 to 245
OPEN/CLOSE
0=Timeout,
1=Ready,
2=Recyle,
3=Startup,
4=Running,
5=Demand,
6=Ramping,
7=Autorest,
8=Override,
9=Tripout,
10=Control Test,
11=Lockout,
12=Pumpdown,
13=Prestart
0 to 32767
0 to 200
1=Normal,
2=Alert, 3=Alarm
AV:40
sys_alm_1
Run Status
37
611
APPENDIX B — OPTIONAL BACNET COMMUNICATIONS WIRING (cont)
Table G — Network Points List (cont)
POINT DESCRIPTION
System Cooling Demand
Level
System Demand Limiting
Target Guide Vane Position
Target VFD Speed
Tower Fan Relay High
Tower Fan Relay Low
User Defined Analog 1
User Defined Analog 2
User Defined Analog 3
User Defined Analog 4
User Defined Analog 5
User Defined Binary 1
User Defined Binary 2
User Defined Binary 3
User Defined Binary 4
User Defined Binary 5
CHW
R
VFD
W
—
—
—
—
CCN
POINT NAME
READ/
WRITE
UNITS
DEFAULT
VALUE
RANGE
BACNET
OBJECT ID
BACNET
OBJECT NAME
N/A
R
N/A
N/A
N/A
AV:9006
cool_demand_level_1
N/A
GV_TRG
VFD_OUT
TFR_HIGH
TFR_LOW
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
N/A
%
%
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
OFF
OFF
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
OFF/ON
0 to 100
0 to 100
OFF/ON
OFF/ON
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
BV:3
AV:41
AV:42
BV:13
BV:14
AV:2901
AV:2902
AV:2903
AV:2904
AV:2905
BV:2911
BV:2912
BV:2913
BV:2914
BV:2915
dem_lmt_act_1
gv_trg_1
vfd_out_1
tfr_high_1
tfr_low_1
user_analog_1_1
user_analog_2_1
user_analog_3_1
user_analog_4_1
user_analog_5_1
user_binary_1_1
user_binary_2_1
user_binary_3_1
user_binary_4_1
user_binary_5_1
LEGEND
Chilled Water
Read
Variable Frequency Drive
Write
38
Copyright 2011 Carrier Corporation
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53190012-01
Printed in U.S.A.
Form 19XRV-3SS
Pg 40
711
3-11
Replaces: New
Download PDF

advertising