Specifications | Carrier 40RU Air Conditioner User Manual

40RU
Packaged Air---Handling Units
60 Hz
With PuronR (R---410A) Refrigerant
Sizes 25, 28, 30
Installation, Start---Up and
Service Instructions
TABLE OF CONTENTS
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . 1
PRE-- INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 2
Moving and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Rigging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 2–22
Chilled Water Coil Freeze Protection . . . . . . . . . . . 26
Coil Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cleaning Cooling Coil . . . . . . . . . . . . . . . . . . . . . . . 26
Cleaning Insulation . . . . . . . . . . . . . . . . . . . . . . . . . 26
Replacing Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
START-- UP CHECKLIST . . . . . . . . . . . . . . . . . . 39-- 40
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SAFETY CONSIDERATIONS
Uncrating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Improper installation, adjustment, alteration, service,
maintenance, or use can cause explosion, fire, electrical
shock or other conditions which may cause personal
injury or property damage. Consult a qualified installer,
service agency, or your distributor or branch for
information or assistance. The qualified installer or
agency must use factory-- authorized kits or accessories
when modifying this product. Refer to the individual
instructions package
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Unit Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Unit Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Refrigerant and Chilled Water Piping Access . . . . . 13
Refrigerant Piping . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Chilled Water Piping . . . . . . . . . . . . . . . . . . . . . . . . 17
Condensate Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Fan Motors and Drives . . . . . . . . . . . . . . . . . . . . . . . 18
Power Supply and Wiring . . . . . . . . . . . . . . . . . . . . 19
Connecting Ductwork . . . . . . . . . . . . . . . . . . . . . . . 21
Return-- Air Filters . . . . . . . . . . . . . . . . . . . . . . . . . . 21
START-- UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23–36
Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Fan Motor Lubrication . . . . . . . . . . . . . . . . . . . . . . . 24
Fan Shaft Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Centering Fan Wheel . . . . . . . . . . . . . . . . . . . . . . . . 24
Fan Shaft Position Adjustment . . . . . . . . . . . . . . . . 24
Individual Fan Wheel Adjustment . . . . . . . . . . . . . . 25
Fan Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Fan Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Fan Pulley Alignment . . . . . . . . . . . . . . . . . . . . . . . 25
Pulley and Drive Adjustment . . . . . . . . . . . . . . . . . . 25
Condensate Drains . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Return-- Air Filters . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Follow all safety codes. Wear safety glasses and work
gloves. Use quenching cloths for brazing operations and
have a fire extinguisher available. Read these instructions
thoroughly and follow all warnings or cautions attached to
the unit. Consult local building codes and appropriate
national electrical codes (in USA, ANSI/NFPA70,
National Electrical Code (NEC); in Canada, CSA C22.1)
for special requirements.
It is important to recognize safety information. This is the
. When you see this symbol on the
safety-- alert symbol
unit and in instructions or manuals, be alert to the
potential for personal injury.
Understand the signal words DANGER, WARNING,
CAUTION, and NOTE. These words are used with the
safety-- alert symbol. DANGER identifies the most serious
hazards which will result in severe personal injury or
death. WARNING signifies hazards which could result in
personal injury or death. CAUTION is used to identify
unsafe practices, which may result in minor personal
injury or product and property damage. NOTE is used to
highlight suggestions which will result in enhanced
installation, reliability, or operation.
!
PRE--INSTALLATION
WARNING
1. The power supply (v, ph, and Hz) must correspond to
that specified on unit rating plate.
2. The electrical supply provided by the utility must be
sufficient to handle load imposed by this unit.
3. Refer to Installation, General section (page 2) and
Fig. 1 and Fig. 2 for locations of electrical inlets, condensate drain, duct connections, and required clearances before setting unit in place.
4. This installation must conform with local building
codes and with the NEC (National Electrical Code) or
ANSI (American National Standards Institute)/NFPA
(National Fire Protection Association) latest revision.
Refer to provincial and local plumbing or wastewater
codes and other applicable local codes.
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could cause in personal
injury or death.
Before performing service or maintenance operations
on unit, always turn off main power switch to unit and
install lockout tag. Unit may have more than one
power switch.
40RU
!
WARNING
UNIT OPERATION AND SAFETY HAZARD
Failure to follow this warning could cause in personal
injury,death and/or equipment damage.
PuronR (R-- 410A) refrigerant systems operate at
higher pressures than standard R-- 22 systems. Do not
use R-- 22 service equipment or components on Puron
refrigerant equipment.
!
WARNING
PERSONAL INJURY AND ENVIRONMENTAL
HAZARD
Failure to follow this warning could cause in personal
injury or death.
Relieve pressure and recover all refrigerant before
system repair or final unit disposal.
Wear safety glasses and gloves when handling
refrigerants. Keep torches and other ignition sources
away from refrigerants and oils.
Moving and Storage - To transfer unit from truck to
storage site, use a fork truck. Do not stack units more than
2 high during storage. If unit is to be stored for more than
2 weeks before installation, choose a level, dry storage
site free from vibration. Do not remove plastic wrap or
skid from unit until final installation.
Rigging - All 40RU Series units can be rigged by using
the shipping skid. Units are shipped fully assembled. Do
not remove shipping skids or protective covering until
unit is ready for final placement; damage to bottom panels
can result. Use slings and spreader bars as applicable to
lift unit.
INSTALLATION
General - Allow the following clearances for service
access and airflow:
S Rear: 3 ft (914 mm) [21/2 ft (762 mm) with electric heat
accessory]
S Front: 21/2 ft (762 mm)
!
CAUTION
CUT HAZARD
Failure to follow this caution may result in personal
injury.
Sheet metal parts may have sharp edges or burrs. Use
care and wear appropriate protective clothing, safety
glasses and gloves when handling parts and servicing
40RU units.
!
CAUTION
UNIT OPERATION HAZARD
Failure to follow this caution could cause equipment
damage.
Ensure voltage listed on unit data plate agrees with
electrical supply provided for the unit.
S Right Side: 31/2 ft (1067 mm)
S Left Side: 21/2 ft (762 mm)
For units equipped with an economizer, refer to the
accessory installation instructions for additional clearance
requirements. Be sure floor, wall, or ceiling can support
unit weight (Tables 1A – 1F). See Fig. 1 and Fig. 2 for
dimensions.
Uncrating - Move unit as near as possible to final
location before removing shipping skid.
Remove metal banding, top skid, and plastic wrap.
Examine unit for shipping damage. If shipping damage is
evident, file claim with transportation agency. Remove
base skid just prior to actual installation.
Check nameplate information against available power
supply and model number description in Fig. 3.
NOTE: Be sure to remove the styrofoam shipping pad
from the thermostatic expansion valve (TXV). Verify that
it has been removed. See Fig. 5.
Accessories - Refer to instructions shipped with each
accessory for specific information.
2
Table 1A — 40RUA Physical Data, English — Cooling Units
UNIT 40RUA*
25
28
30
NOMINAL CAPACITY (Tons)
20
25
30
Base Unit with TXV
730
1050
1062
Plenum
225
325
325
OPERATING WEIGHT (lb)
FANS
Qty...Diam. (in.)
2...15
2...18
2...18
Nominal Airflow (cfm)
8000
10000
12000
6000 – 10000
7500 – 12500
9000 – 15000
208/230---3---60 and 460---3---60
5.0
7.5
10.0
575---3---60
5.0
7.5
10.0
208/230---3---60 and 460---3---60
1745
1745
1745
575---3---60
1745
1755
1755
Airflow Range (cfm)
Nominal Motor Hp (Standard Motor)
REFRIGERANT
Operating charge (lb)
(approx per circuit){
DIRECT ---EXPANSION COIL
R--- 410A
3.5
4.5
Enhanced Copper Tubes, Aluminum Sine--- Wave Fins
Max Working Pressure (psig)
Face Area (sq ft)
5.0
650
19.88
24.86
No. of Splits
2
2
2
No. of Circuits per Split
18
20
24
Split Type...Percentage
Rows...Fins/in.
29.83
Face...50/50
4...15
4...15
4...15
2...11/8
2...13/8
2...13/8
PIPING CONNECTIONS,
Quantity...Size (in.)
DX Coil — Suction (ODF)
2...5/8
DX Coil — Liquid Refrigerant (ODF)
1...21/2
Steam Coil, In (MPT)
1...1/2
Steam Coil, Out (MPT)
Hot Water Coil, In (MPT)
1...2
Hot Water Coil, Out (MPT)
1...2
1...11/4 ODM/1 IDF
Condensate (PVC)
FILTERS
Quantity...Size (in.)
Throwaway — Factory Supplied
4...16 x 20 x 2
4...16 x 24 x 2
Access Location
4...20 x 24 x 2
4...20 x 25 x 2
Either Side
STEAM COIL}
Max Working Pressure (psig at 260° F)
20
Total Face Area (sq ft)
13.33
15.0
15.0
Rows...Fins/in.
1...10
1...10
1...10
Total Face Area (sq ft)
13.33
15.0
15.0
Rows...Fins/in.
2...8.5
2...12.5
2...12.5
HOT WATER COIL}
Max Working Pressure (psig)
150
Water Volume
(gal)
13.9
(ft3)
14.3
1.90
LEGEND
DX — Direct Expansion
TXV — Thermostatic Expansion Valve
{
Units are shipped without refrigerant charge.
}
Field installed accessory only.
3
40RU
Motor Speed (rpm)
Table 1B — 40RUA Physical Data, SI — Cooling Units
UNIT 40RUA*
25
28
30
NOMINAL CAPACITY (kW)
70
87
105
Base Unit with TXV
331
477
482
Plenum
102
148
148
2...381
2...457
2...457
3775
4119
5663
2831 – 4719
3539 – 5899
4247 – 7079
208/230---3---60 and 460---3---60
3.73
5.60
7.46
575---3---60
3.73
5.60
7.46
208/230---3---60 and 460---3---60
29.1
29.1
29.1
575---3---60
29.1
29.3
29.3
OPERATING WEIGHT (kg)
FANS
Qty...Diam. (mm)
Nominal Airflow (L/s)
Airflow Range (L/s)
Nominal Motor kW (Standard Motor)
40RU
Motor Speed (r/s)
REFRIGERANT
R--- 410A
Operating charge (kg)
(approx per circuit){
DIRECT ---EXPANSION COIL
1.59
2.04
2.27
Enhanced Copper Tubes, Aluminum Sine--- Wave Fins
Max Working Pressure (kPag)
4481
Face Area (sq m)
1.85
2.30
No. of Splits
2
2
2
No. of Circuits per Split
18
20
24
Split Type...Percentage
2.77
Face...50/50
Rows...Fins/m
4...591
4...591
4...591
2...11/8
2...13/8
2...13/8
PIPING CONNECTIONS,
Quantity...Size (in.)
DX Coil — Suction (ODF)
2...5/8
DX Coil — Liquid Refrigerant (ODF)
1...21/2
Steam Coil, In (MPT)
1...1/2
Steam Coil, Out (MPT)
Hot Water Coil, In (MPT)
1...2
Hot Water Coil, Out (MPT)
1...2
1...11/4 ODM/1 IDF
Condensate (PVC)
FILTERS
Quantity...Size (mm.)
Throwaway — Factory Supplied
4...406 x 508 x 51
4...406 x 610 x 51
Access Location
4...508 x 610 x 51
4...508 x 635 x 51
Either Side
STEAM COIL}
Max Working Pressure (kPag at 126° C)
Total Face Area (sq m)
Rows...Fins/m
138
1.24
1.39
1.39
1...394
1...394
1...394
HOT WATER COIL}
Max Working Pressure (kPag)
Total Face Area (sq m)
Rows...Fins/m
1034
1.24
1.39
1.39
2...335
2...335
2...335
Water Volume
(L)
52.6
54.1
(m3)
0.052
0.054
LEGEND
DX — Direct Expansion
TXV — Thermostatic Expansion Valve
{
Units are shipped without refrigerant charge.
}
Field installed accessory only.
4
Table 1C — 40RUQ Physical Data, English — Heat Pump Units
UNIT 40RUQ*
25
NOMINAL CAPACITY (Tons)
20
OPERATING WEIGHT (lb)
Base Unit with TXV
720
Plenum
140
FANS
Qty...Diam. (in.)
2...15
Nominal Airflow (cfm)
8000
Airflow Range (cfm)
6000--- 10000
Nominal Motor Hp (Standard Motor)
208/230---3---60 and 460---3---60
5.0
575---3---60
5.0
208/230---3---60 and 460---3---60
1745
575---3---60
1745
REFRIGERANT
R--- 410A
Operating charge (lb)
(approx per circuit){
DIRECT ---EXPANSION COIL
3.5/3.5
Enhanced Copper Tubes, Aluminum Sine--- Wave Fins
Max Working Pressure (psig)
650
Face Area (sq ft)
19.9
No. of Splits
2
No. of Circuits per Split
2
Split Type...Percentage
Face....50/50
Rows...Fins/in.
4...15
PIPING CONNECTIONS,
Quantity...Size (in.)
2...11/8
DX Coil — Suction (ODF)
2...5/8
DX Coil — Liquid Refrigerant (ODF)
1...21/2
Steam Coil, In (MPT)
1...11/2
Steam Coil, Out (MPT)
Hot Water Coil, In (MPT)
1...2
Hot Water Coil, Out (MPT)
1...2
1...11/4 ODM/1 IDF
Condensate (PVC)
FILTERS
Throwaway — Factory Supplied
Quantity...Size (in.)
4...16 x 20 x 2
4...16 x 24 x 2
Right or Left Side
Access Location
STEAM COIL}
Max Working Pressure (psig at 260° F)
20
Total Face Area (sq ft)
13.33
Rows...Fins/in.
1...10
HOT WATER
COIL}
Max Working Pressure (psig)
150
Total Face Area (sq ft)
13.33
Rows...Fins/in.
2...8.5
Water Volume
(gal)
13.9
(ft3)
1.85
LEGEND
DX — Direct Expansion
TXV — Thermostatic Expansion Valve
{
Units are shipped without refrigerant charge.
}
Field installed accessory only.
5
40RU
Motor Speed (rpm)
Table 1D — 40RUA Physical Data, SI — Heat Pump Units
UNIT 40RUQ*
25
NOMINAL CAPACITY (kW)
70
OPERATING WEIGHT (kg)
Base Unit with TXV
326
Plenum
44
FANS
Qty...Diam. (mm)
2...381
Nominal Airflow (L/s)
3775
Airflow Range (L/s)
2831--- 4719
Nominal Motor kW (Standard Motor)
208/230---3---60 and 460---3---60
3.73
575---3---60
3.73
40RU
Motor Speed (r/s)
208/230---3---60 and 460---3---60
29.1
575---3---60
29.1
REFRIGERANT
R--- 410A
Operating charge (kg)
(approx per circuit){
DIRECT ---EXPANSION COIL
1.59/1.59
Enhanced Copper Tubes, Aluminum Sine--- Wave Fins
Max Working Pressure (kPag)
4482
Face Area (sq m)
1.85
No. of Splits
2
No. of Circuits per Split
2
Split Type...Percentage
Face...50/50
Fins/m
591
PIPING CONNECTIONS,
Quantity...Size (in.)
2...11/8
DX Coil — Suction (ODF)
2...5/8
DX Coil — Liquid Refrigerant (ODF)
1...21/2
Steam Coil, In (MPT)
1...11/2
Steam Coil, Out (MPT)
Hot Water Coil, In (MPT)
1...2
Hot Water Coil, Out (MPT)
1...2
1...11/4 ODM/1 IDF
Condensate (PVC)
FILTERS
Throwaway — Factory Supplied
Quantity...Size (mm)
4...406 x 610 x 51
4...406 x 508 x 51
Access Location
Right or Left Side
STEAM COIL}
Max Working Pressure (kPag at 126° C)
138
Total Face Area (sq m)
1.24
Rows...Fins/m
HOT WATER
1...394
COIL}
Max Working Pressure (kPag)
1034
Total Face Area (sq m)
1.24
Rows...Fins/m
2...335
Water Volume
(L)
52.6
(m3)
0.052
LEGEND
DX — Direct Expansion
TXV — Thermostatic Expansion Valve
{
Units are shipped without refrigerant charge.
}
Field installed accessory only.
6
Table 1E — 40RUS Physical Data, English — Chilled Water Units
UNIT 40RUS*
25
28
30
NOMINAL CAPACITY (Tons)
20
25
30
Base Unit
683
1035
1042
Plenum
225
325
325
OPERATING WEIGHT (lb)
FANS
Qty...Diam. (in.)
2...15
2...18
2...18
Nominal Airflow (cfm)
8000
10000
12000
6000 – 10000
7500 – 12500
9000 – 15000
208/230---3---60 and 460---3---60
5.0
7.5
10.0
575---3---60
5.0
7.5
10.0
208/230---3---60 and 460---3---60
1745
1745
1745
575---3---60
1745
1755
1755
Airflow Range (cfm)
Nominal Motor Hp (Standard Motor)
CHILLED WATER COIL
Enhanced Copper Tubes, Aluminum Sine--- Wave Fins
Max Working Pressure (psig)
435
Face Area (sq ft) – Upper
11.0
12.4
15.5
Face Area (sq ft) – Lower
8.3
12.4
12.4
Rows...Fins/in.
3...15
PIPING CONNECTIONS,
Quantity...Size (in.)
Chilled Water — In.
Chilled Water — Out
2...13/8 ODM
2...21/ ODM
8
Steam Coil, In (MPT)
Steam Coil, Out (MPT)
Hot Water Coil, In (MPT)
2...21/ ODM
8
2...21/ ODM
8
2...21/ ODM
8
1...21/2
1...11/2
1...2
Hot Water Coil, Out (MPT)
1...2
1...11/4 ODM/1 IDF
Condensate (PVC)
FILTERS
Throwaway — Factory Supplied
Quantity...Size (in.)
4...16 x 20 x 2
4...16 x 24 x 2
Access Location
STEAM
2...21/8 ODM
4...20 x 24 x 2
4...20 x 25 x 2
Either Side
COIL}
Max Working Pressure (psig at 260° F)
20
Total Face Area (sq ft)
13.33
15.0
15.0
Rows...Fins/in.
1...10
1...10
1...10
Total Face Area (sq ft)
13.33
15.0
15.0
Rows...Fins/in.
2...8.5
2...12.5
2...12.5
HOT WATER COIL}
Max Working Pressure (psig)
150
Water Volume
(gal)
13.9
14.3
(ft3)
1.1
1.90
LEGEND
}
Field installed accessory only.
7
40RU
Motor Speed (rpm)
Table 1F — 40RUS Physical Data, SI — Chilled Water Units
UNIT 40RUS*
25
28
30
NOMINAL CAPACITY (kW)
70
87
105
OPERATING WEIGHT (kg)
Base Unit
Plenum
310
102
469
148
473
148
2...381
3775
2831 – 4719
2...457
4719
3539 – 5899
2...457
5663
4247 – 7079
3.73
3.73
5.60
5.60
7.46
7.46
29.1
29.1
29.1
29.3
29.1
29.3
40RU
FANS
Qty...Diam. (mm)
Nominal Airflow (L/s)
Airflow Range (L/s)
Nominal Motor kW (Standard Motor)
208/230---3---60 and 460---3---60
575---3---60
Motor Speed (r/s)
208/230---3---60 and 460---3---60
575---3---60
CHILLED WATER COIL
Max Working Pressure (kPag)
Face Area (sq m) – Upper
Face Area (sq m) – Lower
Rows...Fins/m
PIPING CONNECTIONS,
Quantity...Size (in.)
Chilled Water — In
Chilled Water — Out
Steam Coil, In (MPT)
Steam Coil, Out (MPT)
Hot Water Coil, In (MPT)
Hot Water Coil, Out (MPT)
Condensate (PVC)
FILTERS
Quantity...Size (mm.)
Access Location
STEAM COIL}
Max Working Pressure (kPag at 125° C)
Total Face Area (sq m)
Rows...Fins/m
HOT WATER COIL}
Max Working Pressure (kPag)
Total Face Area (sq m)
Rows...Fins/m
Water Volume
(L)
(m3)
Enhanced Copper Tubes, Aluminum Sine--- Wave Fins
2999
1.02
1.15
1.44
0.77
1.15
1.15
3...591
3...591
3...591
2...13/8 ODM
2...13/8 ODM
2...21/8 ODM
2...21/8 ODM
Throwaway — Factory Supplied
4...406 x 508 x 51
4...508 x 610 x 51
4...406 x 610 x 51
4...508 x 635 x 51
Either Side
1.24
1...394
138
1.39
1...394
1.39
1...394
1.24
2...335
1034
1.39
2..493
1.39
2...493
52.6
0.052
LEGEND
}
2...21/8 ODM
2...21/8 ODM
1...21/2
1...11/2
1...2
1...2
1...11/4 ODM/1 IDF
Field installed accessory only.
8
54.1
0.054
40RU
LEGEND
TXV — Thermostatic Expansion Valve
NOTES:
1. Dimensions in [ ] are in millimeters.
2.
Direction of airflow.
3. Recommended clearance:
• Rear: 3 in. [914 mm] (2 ft, 6 in. [762 mm]
with electric heat accessory)
• Front: 2 ft, 6 in. [762 mm]
• Right Side: 2 ft, 6 in. [762 mm]
• Left Side: 2 ft, 6 in. [762 mm]
• Local codes or jurisdiction may prevail.
4. Liquid piping not supplied by Carrier.
5. Duct flange is factory supplied and field
installed.
UNIT WEIGHT
lb (kg)
40RUA*25
730 (331)
40RUQ*25
720 (326)
40RUS*25
683 (310)
UNIT
Fig. 1 - Dimensions – Size 25
9
C10722
40RU
LEGEND
TXV — Thermostatic Expansion Valve
NOTES:
1. Dimensions in [ ] are in millimeters.
2.
Direction of airflow.
3. Recommended clearance:
• Rear: 3 in. [914 mm] (2 ft, 6 in. [762 mm]
with electric heat accessory)
• Front: 2 ft, 6 in. [762 mm]
• Right Side: 2 ft, 6 in. [762 mm]
• Left Side: 2 ft, 6 in. [762 mm]
• Local codes or jurisdiction may prevail.
4. Liquid piping not supplied by Carrier.
5. Duct flange is factory supplied and field
installed.
6. 40RUS may require alternate or additional
field favricated poping access holes
UNIT
40RUA*28
40RUA*30
40RUS*28
40RUS*30
Fig. 2 - Dimensions – Sizes 28 and 30
10
UNIT WEIGHT
lb (kg)
1050 (477)
1062 (482)
1035 (469)
1042 (473)
C10723
1
2
4
0 R U A A 2
3
4
5
6
7
_____________
8
9
10 11 12 13 14 15 16 17 18
5 A 1 A 6
– 0 A 0 A 0
____
Model Type
Brand / Packaging
40RU = Carrier Fan Coil
Puronr R–410ARefrigerant
0 = Standard
Not Used
A = Place Holder
Type of Coil
A = StandardDXCoil
Q = Heat Pump
S = Chilled Water Coil
Service Options
0 = Non-Painted Cabinet
1 = Painted Cabinet
Refrigerant Options
A = None
Not Used
A = Place Holder
Nominal Tonnage
25 = 20 Tons
28 = 25 Tons
30 = 30 Tons
40RU
Not Used
0 = Place Holder
Design Rev
– = Catalog Model Number
1 = Design Revision (original)
Not Used
A = Place Holder
Indoor Fan Options
1 = Fan Drive and Motor - Low / Motor Efficiency - Standard
Voltage
1 = 575/3/60
5 = 208/ 230/3/60
6 = 460/3/60
2 = Fan Drive and Motor - Med / Motor Efficiency - Standard
3 = Fan Drive and Motor - High / Motor Efficiency - Standard
Coil Options
A = Al/Cu
C!0724
Fig. 3 - Model Number Nomenclature
POSITION NUMBER
TYPICAL
1
2
2
6
3
1
POSITION
1−2
3−4
5
6−10
4
0
5
G
6
1
7
2
8
3
9
4
10
5
DESIGNATES
Week of manufacture (fiscal calend ar)
Year of manufacture (“10” = 2010)
Manufacturing location (G = ETP, Texas, USA)
Seq uential numb er
C!0725
Fig. 4 - Serial Number Nomenclature
TXV
horizontal arrangement with return air entering
horizontally and the supply air discharging horizontally.
When applying the unit in a horizontal arrangement,
ensure the condensate drain pan is located at the bottom
center of the unit for adequate condensate disposal. See
Fig. 6 for condensate connections for each unit position.
COIL
PLUG
PLUG
CONDENSATE
DRAIN
REMOVE FOAM BLOCK
LEGEND
TXV — Thermostatic Expansion Valve
Fig. 5 - Foam Block Location
LEGEND
Accessory Line
Alternate Air Intake and Discharge
C10683
Air Intake and Discharge
Unit Positioning - The unit can be mounted on the floor
for vertical application with return air entering the face of
the unit and supply air discharging vertically through the
top of the unit. The unit can also be applied in a
Note: Maintain recommended clearances
per Fig. 1 and Fig. 2
Fig. 6 - Typical Unit Positioning
11
C10684
Typical positioning and alternate return air locations are
shown in Fig. 6. Alternate return air locations can be used
by moving the unit panel from the alternate return air
location to the standard return air location. Refer to
overhead suspension accessory drawing (Fig. 7) for
preferred suspension technique. The unit needs support
underneath to prevent sagging.
IMPORTANT: Do NOT attempt to install unit with return
air entering top panel of unit. Condensate will not drain from
unit.
40RU
OVERHEAD SUSPENSION ACCESSORY — UNIT SIZE 25
OVERHEAD SUSPENSION ACCESSORY — UNIT SIZES 28, 30
NOTE: Dimensions in [ ] are millimeters
Fig. 7 - Preferred Suspension Technique
12
C10728
Be sure that unit is level and adequately supported. Use
channels at front and sides of unit for reference points
when leveling.
Refrigerant and Chilled Water Piping Access - The
40RU Series units come with standard knockouts for
refrigerant and chilled water piping. These knockouts are
located on both sides of the unit for installation flexibility.
The standard knockouts provide sufficient access to the
unit’s coils for all 40RUA*25, 28, and 30 units.
40RUQ*25 units, as well as 40RUS*25, 28, and 30 units
require additional holes which must be field-- fabricated to
accommodate the piping. See Fig. 8 for the positions and
dimensions of the additional access holes required for
40RUQ and 40RUS units. Recommended access hole use
is also listed for all units. Note that Fig. 8 shows the
access holes on the control-- box side of the unit; this is the
side of the unit with the coil headers, so it is used most
often for piping access.
IMPORTANT:
underground.
Do
not
bury
refrigerant
piping
Refrigerant Piping - See Tables 1A–1F for refrigerant
pipe connection sizes. For ease in brazing, it is
recommended that all internal solder joints be made
before unit is placed in final position.
The 40RU direct-- expansion units have internal
factory-- installed thermostatic expansion valves (TXVs),
distributors, and nozzles for use with R-- 410A. See Table
2 for part numbers. Knockouts are provided in the unit
corner posts for 40RU refrigerant piping. See Fig. 8,
which also lists recommended knockouts and access holes
to use for each 40RU unit size. Recommended fittings are
listed in Table 3.
The sensor bulb capillary tubes must be routed from the
TXVs inside the unit through one of the piping access
holes. Clamp the TXV sensor bulb on a vertical portion of
the suction line, outside the unit. See Fig. 9.
NOTE: Be sure to remove the styrofoam shipping pad
from the TXV. Verify that it has been removed. See Fig. 5.
IMPORTANT: Never attach the sensor to the suction
manifold. Do NOT mount the sensor on a trapped portion
of the suction line.
The 40RU Series evaporator coils have a face-- split
design. Ensure that lower circuit of coil is first on/last off
when connected to the condensing unit and/or system
controls. See Fig. 10.
External TXV equalizer connections are provided and
factory-- brazed into the coil suction manifolds.
If suction line must be horizontal, clamp bulb to suction
line at least 45 degrees above bottom, at approximately
the 4 o’clock or 8 o’clock position. See Fig.11.
8
7
6
5
A
4
B
C
D
3
2
1
C10727
FIELD--FABRICATED HOLE DIAMATERS
in. (mm)
FIELD--FABRICATED HOLE POSITION DIMENSIONS
in. (mm)
UNIT
USE HOLE
NUMBERS
No. 5
No. 6
No. 7
No. 8
A
B
C
D
40RUA*25, 28, 30
1,2, 3, 4
—
—
—
—
—
—
—
—
40RUS*25
4, 5, 6, 7
13/4 (44.5)
13/4 (44.5)
13/4 (44.5)
—
3.0 (76.2)
6.0 (152.5)
10.5 (266.7)
—
40RUQ*25
3{,
11/8
11/8
(28.6)
13/4 (44.5)
—
3.25 (82.6)
6.125 (155.6)
10.38 (263.7)
21/2 (63.5)
21/2 (63.5)
21/2 (63.5)
6.0 (152.5)
9.625 (244.5)
13.38 (339.9)
40RUS*28, 30
5, 6, 7
5, 6, 7, 8
(28.6)
21/2 (63.5)
{ Must be enlarged from 11/ in. (28.6mm) to 13/ in. (44.5mm)
8
4
NOTE: Access hole knockouts 1--- 4 are factory--- supplied.
Fig. 8 - Refrigerant and Chilled Water Piping Access Holes
13
17.0 (431.8)
40RU
Unit Isolation - Where extremely quiet operation is
essential, install isolators between floor and base of unit,
or between ceiling and top section of unit.
EQUALIZER LINE
TXV
SENSING
BULB
UPPER
SPLIT
SOLENOID
VALVE
AIRFLOW
15 DIAMS
MIN
15 DIAMS
MIN
TXV
10
DIAMS
8 DIAMS
MIN
40RU
SIGHT
GLASS
8 DIAMS
MIN
EQUALIZER
FILTER
LINE
DRIER
TXV
SENSING
BULB
LOWER
SPLIT
AIRFLOW
TXV
10
DIAMS
INDOOR
COIL
LEGEND:
TXV – Thermostatic Expansion Valve
NOTE: Component location arrangemetshown for field installation of
sight glasses, solenoid valves, filter driers, and TXV sensing bulbs.
The TXVs and equilizer lines are factory installed.
Fig. 9 - Face-- Split Coil Suction and Liquid Line Piping (Typical)
C10726
LEGEND
TXV — Thermostatic Expansion Valve
NOTE: The 8 o’clock position is shown above.
FIRST ON/LAST OFF = B
VERTICAL INSTALLATION
Fig. 11 - TXV Sensing Bulb Location
FIRST ON/LAST OF F = A
HORIZONTAL INSTALLATIO N
C10688
Fig. 10 - Typical Evaporator Coil Connections (40RU)
14
C10689
Table 2 – Factory-- Installed Nozzle and Distributor Data
TXV
Qty...Part No.
DISTRIBUTOR
Qty...Part No.
FEEDER TUBES
PER DISTRIBUTOR{
Qty...Size (in.)
4 Row
2...BBIZE--- 8--- GA
2...D196--- 18--- 3/16
18...3/16
2...G6
4 Row
2...BBIZE--- 15--- GA
2...1126
20...3/16
2...C15
4 Row
2...BBIZE--- 15--- GA
2...1126
24...3/16
2...C17
2--- 12...3/16
2...G8
UNIT
COIL TYPE
STD
40RUA*25
40RUA*28
40RUA*30
40RUQ*25
4 Row
2...BBIZE--- 12.5--- GA
2...113--- 12--- 3/
16
NOZZLE
Qty...Part No.
{ Feeder tube size is 1/ in. (6.35 mm).
4
NOTE: Hot gas bypass applications require field---supplied auxiliary side connector.
Table 3 – Fitting Requirements
UNIT
ACCESS
HOLE NO.}
CONNECTION
TYPE
FITTINGS REQUIRED†
(in.)
CIRCUIT
1
Suction
Lower
11/8 Nipple, 75/8 L
11/8 Long Radius Elbow
2
Liquid
Lower
40RUA*25
3
Liquid
Upper
5/
8
Street Elbow
5/
8
Nipple, 61/2 L
5/
8
Long Radius Elbow
5/
8
Street Elbow
5/
8
Nipple, 91/2 L
5/
8
Long Radius Elbow
11/8 Nipple, 55/8 L
4
Suction
Upper
11/8 Long Radius Elbow
11/8 Nipple, 11 L
11/8 Long Radius Elbow
3
5
Suction
Lower
Suction
Lower
40RUQ*25
6
Liquid
Upper
11/8 Nipple, 3 L
11/8 Long Radius Elbow
5/
8
Nipple, 27/8 L
5/
8
45_ Elbow
5/
8
Nipple, 15/8 L
5/
8
Long Radius Elbow
5/
8
Nipple, 27/8 L
5/
8
45_ Elbow
5/
8
Nipple, 41/4 L
5/
8
Long Radius Elbow
11/8 Nipple, 5 L
7
Suction
Upper
11/8 45_ Elbow
11/8 Nipple, 83/4 L
11/8 Long Radius Elbow
13/8 Long Radius Elbow
4
Supply
Lower
13/8 Nipple, 33/4 L
13/8 Long Radius Elbow
13/8 Long Radius Elbow
5
Return
Lower
40RUS*25
13/8 Nipple, 33/8 L
13/8 Long Radius Elbow
13/8 Long Radius Elbow
6
Return
Upper
13/8 Nipple, 7 L
13/8 Long Radius Elbow
13/8 Long Radius Elbow
7
Supply
Upper
13/8 Nipple, 113/4 L
11/8 Long Radius Elbow
}
†
See Fig. 8 for access hole location by number.
Fittings are listed in order from header or tee stub connection out to access hole in corner support post.
15
40RU
11/8 Street Elbow
Table 3 — Fitting Requirement (cont)
UNIT
ACCESS
HOLE NO.}
CONNECTION
TYPE
FITTINGS REQUIRED†
(in.)
CIRCUIT
13/8 Street Elbow
1
Suction
Lower
13/8 Nipple, 11 L
13/8 Long Radius Elbow
2
Liquid
Lower
40RUA*28
3
Liquid
Upper
5/
8
Street Elbow
5/
8
Nipple, 11/2 L
5/
8
Long Radius Elbow
5/
8
Street Elbow
5/
8
Nipple, 191/2 L
5/
8
Long Radius Elbow
13/8 Nipple, 43/16 L
4
Suction
Upper
13/8 Long Radius Elbow
13/8 Nipple, 231/4 L
13/8 Long Radius Elbow
40RU
21/8 Long Radius Elbow
5
Supply
Lower
21/8 Nipple, 31/2 L
21/8 Long Radius Elbow
21/8 Long Radius Elbow
6
Return
Lower
21/8 Nipple, 3 L
21/8 Long Radius Elbow
40RUS*28, 30
21/8 Long Radius Elbow
7
Return
Upper
21/8 Nipple, 67/8 L
21/8 Long Radius Elbow
21/8 Long Radius Elbow
8
Supply
Upper
21/8 Nipple, 117/8 L
21/8 Long Radius Elbow
13/8 Street Elbow
1
Suction
Lower
13/8 Nipple, 3 L
13/8 Long Radius Elbow
2
Liquid
Lower
40RUA*30
3
Liquid
Upper
5/
8
Street Elbow
5/
8
Nipple, 73/4 L
5/
8
Long Radius Elbow
5/
8
Street Elbow
5/
8
Nipple, 181/2 L
5/
8
Long Radius Elbow
13/8 Nipple, 43/16 L
4
Suction
Upper
13/8 Long Radius Elbow
13/8 Nipple, 191/4 L
13/8 Long Radius Elbow
}
†
See Fig. 8 for access hole location by number.
Fittings are listed in order from header or tee stub connection out to access hole in corner support post.
16
To size, design, and install chilled water piping, consult
the Carrier System Design manual. See Fig. 12 for an
example of a typical installation. Recommended fittings
are listed in Table 3.
Knockouts are provided in the unit corner posts for
40RUS refrigerant piping. Additional field-- fabricated
access holes are required for 40RUS chilled water piping.
See Fig. 8, which lists recommended knockouts and
access holes to use for each 40RUS unit size.
To access 40RUS coil vents and drains, remove the unit
side panel over the coil header. Vent and drain plugs are
on the top and bottom of header, respectively. See the
Service section for information on preventing coil
freeze-- up during winter.
40RU
Chilled Water Piping - See Tables 1E and 1F for chilled
water connection sizes. For ease in brazing, it it
recommended that all internal solder joints be made
before unit is placed in final position.
Fig. 12 - Typical 40RUS Chilled Water Piping
17
C10690
Condensate Drain - Install a trapped condensate drain
line to unit connection as shown in Fig. 13. The unit drain
connection is a PVC stub. See Fig. 14. Some areas may
require an adapter to connect to either galvanized steel or
copper pipe. For these applications, install a
field-- supplied threaded PVC adapter.
40RU
3” MIN.
[76]
Fig. 14 - Drain Pan Slope Adjustment
C10692
As shipped, the unit’s condensate drain pan is NOT sloped
towards the drain connection. The pan slope must be
changed to pitch towards the side of the unit with the
drain connection. See Fig. 14. Loosen the 2 screws next to
the drain outlet at both ends of the unit, push drain pan
down in the slots near the drain connection, and up in the
slots on the opposite end. Re-- tighten screws. The pan
should have a pitch of at least 1/4 - in. over its length
toward the drain connection.
NOTE: Dimensions in [ ] are in millimeters
Fig. 13 - Condensate Drains
C10691
Fan Motors and Drives - Motor and drive packages are
factory installed in all units. The motor and drive
packages consist of the following items:
NOTE: A trap must be installed in the condensate drain
line to ensure that the static pressure of fans is balanced with
the water column in the drain line and that condensate can
drain completely from pan. Without a trap, air can be drawn
up drain line until water level in condensate pan becomes
equal to static pressure created by fans, preventing complete
drainage. Conditions will worsen as filters become dirty.
1 — fan motor
Install clean-- out plugs in trap. Pitch drain line downward
to an open floor drain or sump. Provide service clearance
around drain line to permit removal of unit panels.
Observe all local sanitary codes.
For instructions on changing fan rotation, changing drive
speeds and adjusting drives, see Pulley and Drive
Adjustment in the Service section.
1 — adjustable motor pulley
1 — fan pulley
2 — matched fan belts
(40RUA*25-- 30, 40RUQ*25, 40RUS*25-- 30 units)
18
!
FAN
CONTACTOR
BOX
MOTOR
AND DRIVE
WIRE
ACCESS
FAN DRIVE
PULLEY
CONDENSATE
DRAIN
CONNECTION
(HORIZONTAL)
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal
injury or death.
Do not use gas piping as an electrical ground. Unit
cabinet must have an uninterrupted, unbroken electrical
ground to minimize the possibility of personal injury if
an electrical fault should occur. This ground may consist
of electrical wire connected to unit ground lug in control
compartment, or conduit approved for electrical ground
when installed in accordance with NEC (National
Electrical Code); ANSI/NFPA 70, latest edition (in
Canada, Canadian Electrical Code CSA [Canadian
Standards Association] C22.1), and local electrical
codes.
!
FAN SCROLL
WARNING
FIRE HAZARD
Failure to follow this warning could result in intermittent
operation or performance satisfaction.
Do not connect aluminum wire between disconnect
switch and fan coil unit. Use only copper wire.
(See Fig. 15)
COIL
FILTER
ELEMENTS
TXV BULB
ACCESS
REFRIGERANT
PIPING ACCESS
FILTER
RETAINER
CLIP
CONDENSATE
DRAIN
CONNNECTION
(VERTICAL)
LEGEND
TXV — Thermostatic Expansion Valve
Fig. 16 - Wiring and Service Access
(Side Panel Removed)
C10693
Fan motors are factory-- installed on all units. Indoor-- fan
contactors are located in the fan contactor box behind the
side access panel (see Fig. 16 and 17). Wire the thermostat
to the 24-- v control circuit terminal block located in the
side of the fan contactor control box, according to Fig. 18
or the unit label diagram. If the air handler is part of a
split system, complete the wiring from the condensing
unit to the thermostat shown in Fig. 18.
105° C 600V
RJ A
ELECTRIC
DISCONNECT
SWITCH
COPPER
13
12
11
W
23
22
21
WIRE ONLY
ALUMINUM
WIRE
Fig. 15 - Disconnect Switch and Unit
FAN
CONTACTOR
A93033
Install disconnect switch and power wiring in accordance
with all applicable local codes. See Fig. 15-- 17 and the
unit label diagram. Connect power wiring with 1/4 - in.
ring terminal.
24V
TERMINAL
BLOCK
POWER
WIRING
KNOCKOUT
C10694
Fig. 17 - Fan Contactor Box and Terminal Block
(Cover Removed) (Typical)
19
40RU
Power Supply and Wiring - Check the unit data plate to
ensure that available power supply matches electrical
characteristics of the unit. Provide a disconnect switch
with an integrated lock-- out feature of size required to
provide adequate fan motor starting current. See Tables
4-- 6 for unit electrical data.
Table 4 – Electrical Data, Standard Motors
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA30
40RUS30
FAN MOTOR
POWER SUPPLY
V ---PH ---Hz{
VOLTAGE
LIMITS
Hp (kW)
FLA
Minimum
Circuit Amps
MOCP
208/230--- 3--- 60
187--- 253
5.0 (3.73)
14.7/13.6
18.4/17.0
30/25
460--- 3--- 60
414--- 506
5.0 (3.73)
6.8
8.5
15
575--- 3--- 60
518--- 632
5.0 (3.73)
5.1
6.4
15
208/230--- 3--- 60
187--- 253
7.5 (5.59)
21.4/19.4
26.9/24.3
45/40
460--- 3--- 60
414--- 506
7.5 (5.59)
9.7
12.1
20
575--- 3--- 60
518--- 632
7.5 (5.59)
7.8
9.8
15
208/230--- 3--- 60
187--- 253
10.0 (7.46)
28.0/25.2
35.0/31.5
60/50
460--- 3--- 60
414--- 506
10.0 (7.46)
12.6
15.8
25
575--- 3--- 60
518--- 632
10.0 (7.46)
10.3
12.9
20
40RU
See Legend and Notes below.
Table 5 – Electrical Data, Alternate Motors
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUA*30
40RUS*28
40RUS*30
FAN MOTOR
V ---PH ---Hz{
VOLTAGE
LIMITS
Hp (kW)
208/230--- 3--- 60
187--- 253
460--- 3--- 60
414--- 506
575--- 3--- 60
POWER SUPPLY
FLA
Minimum
Circuit Amps
MOCP
7.5 (5.59)
21.4/19.4
26.9/24.3
45/40
7.5 (5.59)
9.7
12.1
20
518--- 632
7.5 (5.59)
7.8
9.8
15
208/230--- 3--- 60
187--- 253
10.0 (7.46)
28.0/25.2
35.0/31.5
60/50
460--- 3--- 60
414--- 506
10.0 (7.46)
12.6
15.8
25
575--- 3--- 60
518--- 632
10.0 (7.46)
10.3
12.9
20
See Legend and Notes below.
Legend and Notes for Tables 4 and 5
LEGEND:
FLA
--- Full Load Amps
MOCP --- Maximum Overcurrent Protection
{ Motors are designed for satisfactory operation within 10% of
normal voltage shown. Voltages should not exceed the limits
shown in the Voltage Limits column.
Example: Supply voltage is 230-3-60
% Voltage Imbalance
1. Minimum circuit amps (MCA) and MOCP values are calculated in accordance with The NEC. Article 440.
Average Voltage =
2. Motor FLA values are established in accordance with Underwriters’ Laboratories (UL). Standard 1995.
4. Installation with Accessory Electric Heaters
Size the Field Power Wiring between the heater TB1 and the
40RU indoor fan motor per NEC Article 430--- 28 (1) or (2)
(depends on length of conduit between heater enclosure and
40RU power entry location). Install wires in field --- installed
conduit.
max voltage deviation from average voltage
average voltage
AB = 393 v
BC = 403 v
AC = 396 v
NOTES:
3. Unbalanced 3-Phase Supply Voltage
Never operate a motor where a phase imbalance in supply
voltage is greater than 2%. Use the formula in the example
(see column to the right) to determine the percentage of voltage imbalance.
= 100 x
=
(393 + 403 + 396)
=
3
1192
3
397
Determine maximum deviation from average voltage.
(AB) 397 – 393 = 4 v
(BC) 403 – 397 = 6 v
(AC) 397 – 396 = 1 v
Maximum deviation is 4 v.
Determine percent of voltage imbalance.
% Voltage Imbalance
= 100 x
6
397
= 1.5%
This amount of phase imbalance is satisfactory as it is below the
maximum allowable 2%.
IMPORTANT: If the supply voltage phase imbalance is more than
2%, contact your local electric utility company immediately.
20
40RU
Fig. 18 - Unit Wiring
Table 6 – Fan Contactor Coil Data
UNIT
40RU*
VOLTAGE
(vac)
MAXIMUM
HOLDING VA
25, 28, 30
24
10
Connecting Ductwork - Refer to the Carrier System
Design Manual for the recommended design and layout of
ductwork. Fig. 19 shows recommended duct connection to
units with 2 fans.
!
CAUTION
UNIT OPERATION HAZARD
Failure to follow this caution could cause equipment
damage.
Do not operate unit without ductwork or discharge
plenum unless fan speed has been adjusted for
external static pressure of zero in. wg. Failure to do so
may result in motor overload.
DISCHARGE CONNECTIONS — Duct flanges are
factory-- supplied; they are shipped inside the unit attached
to the hairpin end of the coil tube sheet for field
C10695
installation. Using the existing screws, install the duct
flanges on the unit’s fan deck. Each fan discharge requires
2 flanges; each flange must be bent in the middle to
conform to the discharge opening. See Fig. 20. After
flanges are installed, connect them to the supply duct
using a canvas connection to prevent vibration. It is
important that this connection be properly fabricated to
prevent high air friction losses and air noise.
RETURN CONNECTIONS — When using return-- air
ductwork, route return-- air duct to the unit’s return air inlet
near the filter rack, using a canvas connection to prevent
transmission of unit vibration. If the duct blocks off the
unit’s access panel, provide a slip joint in the ductwork to
permit removal for servicing.
OUTDOOR-- AIR INLET CONNECTIONS — Connect
outdoor-- air inlet to field-- installed accessory economizer.
Refer to Economizer Installation Instructions.
Return-- Air Filters - Type and size of filters are shown
in Tables 1A – 1F and are factory-- supplied and
factory-- installed. In all units with 2 fans, a filter
replacement tool (hook) is shipped inside the unit for field
use when replacing filters. See the Service section for
instructions on filter element replacement.
21
40RU
Fig. 19 - Typical Fan Discharge Connections for Multiple Fan Units
Fig. 20 - Duct Flange Installation
22
C10696
C10697
START--UP
2. To increase superheat, turn the stem clockwise. To decrease the superheat, turn the stem counterclockwise.
Do not turn the stem more than one full turn.
3. Wait until suction pressure and superheat stabilize.
This may take more than 30 minutes.
4. Continue adjustment until superheat reaches 10_F to
15_F (5.5_C to 8.3_C).
5. Replace the seal cap; tighten.
Before starting unit, check the following and correct as
necessary:
S Is unit solidly supported?
S Is fan adjusted for speed and pulley alignment?
S Are pulleys, motor, and bearings securely mounted?
S Are there any loose parts that will rattle or vibrate?
INSTALLER / INSTALLATEUR
S Is condensate drain pan pitched for correct drainage?
S Are all panels securely fastened?
La surchauffe TXV doit être vérifiée au
moment de la mise en route initiale et
ajustée si nécessaire. La surchauffe doit
être comprise entre 10 et 15 degrés F.
S Are all electrical connections correct and tight?
40RUA and 40RUQ ONLY —
40RU500073 2.0
S Is TXV bulb located on suction tube per Fig. 21?
Fig. 22 - Label, TXV Adjustment
S Is the capillary tube to the bulb free of kinks and not
subject to pinching?
SERVICE
S Is the bulb well secured to the suction tube with strap?
Also refer to condensing unit or outdoor heat pump section
instructions before starting a split system. A split system
start--up checklist is provided at the end of these instructions.
40RU500072 2.0
IMPORTANT! / IMPORTANT
UPPER SPLIT
BLOC SUPÉRIEUR
AIR FLOW
CIRCULATION
D'AIR
SIGHT GLASS
HUBLOT
LOWER
SPLIT
BLOC
INFÉRIEUR
AIR FLOW
CIRCULATION
D'AIR
S Cleaning or replacement of filters.
SOLENOID
VALVE
VANNE
SOLÉNOÏDE
8 DIAMS MIN
8 x DIA. MIN
S Testing for cooling/heating system leaks.
FILTER
DRIER
FILTRE
DESSICCATEUR
TXV SENSING
BULB
CAPTEUR TXV
S Complete cleaning of cabinet, fan wheel, cooling coil,
condensate pan and drain, heating coils, and return-- air
grille (if present).
S Adjustment of fan motor, belt, bearings, and wheels.
TXV
15 DIAMS MIN 10 DIAMS
15 x DIA. MIN 10 x DIA. MIN
Inspection and maintenance should be performed at
regular intervals and should include the following:
S Inspection of panels and sealing of unit against air
leakage.
EQUALIZER LINE
CONDUITE D'ÉQUILIBRAGE
TXV
SENSING
BULB
CAPTEUR TXV
S Checking of all electrical connections.
!
TXV
EQUALIZER LINE
15 DIAMS MIN 10 DIAMS
15 x DIA. MIN 10 x DIA. MIN
CONDUITE D'ÉQUILIBRAGE
8 DIAMS MIN
8 x DIA. MIN
C10828
INDOOR COIL
ÉCHANGEUR INTÉRIEUR
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal
injury or death.
Before performing service or maintenance operations
on unit, always turn off main power switch to unit and
install lockout tag. Unit may have more than one
power switch.
The sensor bulb capillary tubes must be routed from the TXVs inside the unit through one of the piping
access holes. Clamp the TXV sensor bulb on a vertical portion of the suction line, outside the unit.
See Fig. 7 in the installation, start-up and service instruction. Super heat must be adjusted in field.
Les tubes capillaires du capteur doivent être acheminé à partir du détendeur thermostatique situé à l'intérieur
de l'appareil au travers de l'un des trous d'accès de conduites. Attacher le capteur sur une portion verticale
de la conduite de succion, à l'extérieur de l'appareil. Voir la Figure 7 dans le manuel d'installation, de mise
en marche, et d'entretien. La surchauffe doit être ajustée sur place.
Fig. 21 - Label, TXV Bulb Location
C10827
Adjusting TXV for Superheat
(40RUA and 40 RUQ only) —
The unit-- mounted thermostatic expansion valve(s) is/are
factory set to provided superheat at the bulb location in
10_F to 15_F (5.5_C to 8.3_C) range. Actual system load
conditions may require adjustment of the factory setting.
To adjust the TXV superheat setting:
1. Remove the seal cap from the bottom of the TXV
body.
WARNING
Most unit service can be performed by removing one or
both of the unit’s side panels. Coil cleaning or removal or
insulation cleaning may require removal of a rear, top, or
bottom panel, depending on the unit’s orientation. When
service is completed, replace unit panels.
Panels - Panels are fastened to unit frame with sheet
metal screws. Fan and coil compartment must be sealed
tightly after service to prevent air from bypassing the
cooling coil.
23
40RU
TXV superheat must be checked at initial
unit start-up and adjusted if necessary.
Superheat must be 10 - 15 deg F.
S Are coil baffle plates tight against coil to prevent air
bypass?
Fan Motor Lubrication - Fan motor supplied with unit is
permanently lubricated and requires no further
lubrication.
Fan Shaft Bearings - Size 25-- 30 units have pillow-- block
bearings (Fig. 23) that must be lubricated with suitable
bearing grease approximately every 3 months. See Table 7
for suitable lubricants.
Table 7 – Lubricant Data
MANUFACTURER
LUBRICANT
Mobil
Mobilplex EP No. 2
Sunoco
Prestige 42
Texaco
Multifak 2
Texaco
Regal AFB--- 2*
Centering Fan Wheel - If fan and fan shaft assembly are
not properly centered, blades may scrape against the
blower side scroll plate or may create an objectionable
whistling noise. It may be necessary to adjust individual
fan wheels or move entire fan shaft. See the following two
sections.
Fan Shaft Position Adjustment - Loosen setscrew or
locking collar of each fan shaft bearing. Slide shaft into
correct position and replace locking collar (Fig. 24). To
replace locking collar, push collar up against inner face of
bearing. Turn collar in direction of fan rotation until tight,
and tighten setscrew. Tightening locking collar in
direction of fan rotation results in further tightening of
collar should setscrew work itself loose.
40RU
*Preferred lubricant, contains rust and oxidation inhibitors.
Fig. 24 - Fan Shaft Bearing
C10699
C10698
Fig. 23 - Fan Shaft, Bearings, and Fan Wheel (Typical)
Fig. 25 - Fan Motor Mounting
24
C10700
Individual Fan Wheel Adjustment - Loosen the 2
locking bolts holding fan wheel hub to shaft. See Fig. 23.
Position fan wheel in center of the fan housing and tighten
locking bolts. Clearance between wheel and housing
should be the same on both sides.
If complete belt replacement is required during servicing,
loosen the motor plate mounting bolts (Fig. 25), move
motor/plate assembly towards fan pulley, and pull belt(s)
off pulleys. Reverse the procedure with new bolts and
readjust deflection.
Fig. 27 - Fan Pulley Adjustments
Fan Rotation - Correct fan rotation with respect to fan
outlet is shown in Fig. 26.
C10702
4. If pulleys are not in correct alignment, loosen the motor holddown bolts and slide the motor axially until
the pulleys are aligned.
5. Tighten motor holddown bolts.
Pulley and Drive Adjustment - To obtain desired fan
speed, refer to the fan motor and drive data in Tables
8A-- 11D and adjust fan motor pulley as follows:
Fig. 26 - Fan Rotation
To reverse the direction of rotation of a
motor, reverse any 2 of the power leads.
connection diagram on the inside of motor
cover for proper reversing procedure of
motor.
1. Remove belt from fan motor pulley after loosening
motor from motor base.
2. Loosen setscrew in moveable flange of pulley. Screw
moveable flange toward fixed flange to increase the
fan speed and away from fixed flange to reduce
speed. Before tightening setscrew, make certain that
setscrew is over nearest flat surface of pulley hub
(Fig. 27).
C10701
3-- phase fan
Refer to the
terminal box
single-- phase
!
CAUTION
UNIT OPERATION HAZARD
Failure to follow this caution could cause equipment
damage.
Increasing fan speed produces a greater load on motor.
Do not exceed rated capacity of motor.
Fan Pulley Alignment - Align as follows:
1. Loosen setscrews on pulleys.
2. Align pulleys visually and tighten setscrews on fan
pulley to lock it in place.
3. Use the methods shown in Fig. 27 to check proper
pulley alignment.
Condensate Drains - Keep condensate drains free of dirt
and foreign matter.
Return-- Air Filters - Refer to Replacing Filters section
for filter accessibility and removal. Replace with clean
filters of the sizes listed in Tables 1A-- 1F.
25
40RU
Fan Belts - Motor mounting plate and motor support
angles are slotted to permit both vertical and horizontal
adjustment. Adjust belt(s) for correct deflection by
loosening motor plate mounting bolts, moving motor/plate
assembly forward or back, and re-- tightening bolts. Press
down on belt with one finger midway between fan and
motor pulleys to check deflection. The correct deflection
is 1/8 - in. (3.2 mm). See Fig. 25.
Chilled Water Coil Freeze Protection - Shut off water
supply to unit. Remove side panel of unit and remove vent
and drain plugs in top and bottom of coil header. Drain
coil and blow out remaining water. Reinstall plugs and
side panel.
!
CAUTION
UNIT OPERATION HAZARD
Failure to follow this caution could cause equipment
damage.
Do not operate unit without air filters.
Alternative freeze protection methods follow:
S Circulate hot water within the water coil’s supply main
or supplementary space heating.
S Close off supply lines to unit and open a union or
field-- supplied drain valve in the return line.
40RU
IMPORTANT: Draining from return line will not
completely drain water from coils.
S After draining as much water as possible from coils, add
sufficient antifreeze to prevent residual water in the coil
from freezing.
SLID
E
FILTER
RETAINER
CLIP
S Add a sufficient quantity of non-- corrosive antifreeze to
the entire system to prevent all water within the system
from freezing.
Coil Removal - Remove unit panels and corner posts as
required. Disconnect coil connections and remove fastening
screws. Remove coil through end or side sections of unit.
Cleaning Cooling Coil - Remove return-- air filters.
Remove any heavy dirt that may have accumulated on
underside of coil. Coil can be cleaned more easily with a
stiff brush, vacuum cleaner, or compressed air when coil
is dry. If coil is wet or if water is to be used for cleaning,
guard against splashing water on electrical components or
damaging surrounding area. Clean coil baffles as
applicable and check for tight fit to be sure air does not
bypass coil.
Fig. 28 - Remove Filter Retainer Clip
C10703
Cleaning Insulation - The insulation contains an
immobilized antimicrobial agent that helps prevent the
growth of bacteria and fungi. Clean the inner surface of
the insulation according to the separate maintenance
instructions shipped with the unit.
Replacing Filters - Filters can be removed and installed
from either side of the unit. Install new filters in units that
have one fan as follows:
1. Remove the side access panel (retain screws).
2. Remove the filter retainer clip (see Fig. 28).
3. Remove old filters by lifting and tilting them out of
the filter track. See Fig. 16 and 29. Use the factory-supplied filter hook to slide filters within reach for removal. The filter hook is shipped inside the unit in
the filter track
4. Reverse the procedure to install new filters.
Fig. 29 - Filter Removal/Replacement
26
C10704
Table 8A -- Fan Motor Data, Standard Motor — English
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
1745
1745
1745
5.0
7.5
10.0
Frame (NEMA)
S184T
S213T
S215T
Shaft Dia (in.)
11/8
13/8
13/8
1745
1755
1755
5.0
7.5
10.0
Frame (NEMA)
184T
S213T
D215T
Shaft Dia (in.)
11/8
13/8
13/8
UNIT
208/230---3---60 and 460---3---60
Speed (rpm)
Hp
575---3---60
Speed (rpm)
Hp
40RU
LEGEND
NEMA — National Electrical Manufacturers Association
Table 8B -- Fan Motor Data, Alternate Motor — English
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
1745
1745
1745
208/230---3---60 and 460---3---60
Speed (rpm)
Hp
7.5
10.0
10.0
Frame (NEMA)
S213T
S215T
S215T
Shaft Dia (in.)
13/8
13/8
13/8
1755
1750
1750
575---3---60
Speed (rpm)
Hp
7.5
10.0
10.0
Frame (NEMA)
S213T
D215T
D215T
Shaft Dia (in.)
13/8
13/8
13/8
LEGEND
NEMA — National Electrical Manufacturers Association
27
Table 8C -- Fan Motor Data, Standard Motor — SI
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
Speed (r/s)
29.08
29.08
29.08
Shaft kW
3.73
5.60
7.46
Frame (NEMA)
S184T
S213T
S215T
Shaft Dia (mm)
28.6
34.9
34.9
Speed (r/s)
29.08
29.25
29.25
Shaft kW
3.73
5.60
7.46
Frame (NEMA)
184T
S213T
S215T
Shaft Dia (mm)
28.6
34.9
34.9
UNIT
208/230---3---60 and 460---3---60
40RU
575---3---60
LEGEND
NEMA — National Electrical Manufacturers Association
Table 8D -- Fan Motor Data, Alternate Motor — SI
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
29.08
29.17
29.17
208/230---3---60 and 460---3---60
Speed (r/s)
Shaft kW
5.60
7.46
7.46
Frame (NEMA)
S213T
S215T
S215T
Shaft Dia (mm)
34.9
34.9
34.9
29.25
29.17
29.17
575---3---60
Speed (r/s)
Shaft kW
5.60
7.46
7.46
Frame (NEMA)
S213T
D215T
D215T
Shaft Dia (mm)
34.9
34.9
34.9
LEGEND
NEMA — National Electrical Manufacturers Association
28
Table 9A -- Standard Drive Data, 60 Hz — English
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
Motor Pulley Pitch Diameter (in.)
3.7--- 4.7
4.3--- 5.3
4.3--- 5.3
3.0
3.0
3.0
MOTOR DRIVE
Pulley Factory Setting
Full Turns Open
FAN DRIVE
Pulley Pitch Dia (in.)
9.4
11.0
11.0
Pulley Bore (in.)
17/16
115/16
115/16
Belt No. — Section
2—B
2—B†
2—B†
Belt Pitch (in.)
41.8
(2) 42.8
(2) 43.8
(2) 42.8
(2) 43.8
771
752
752
679--- 863
682--- 841
674--- 831
1200
1100
1100
15.3
13.1
13.1
6
6
6
9.12--- 10.99
6.67--- 9.43
6.67--- 9.43
Factory Setting
Range
Max Allowable Speed (rpm)
1/
2
Change per
Turn of
Moveable Motor Pulley
Flange
MAX FULL TURNS FROM
CLOSED POSITION
SHAFTS CENTER DISTANCE (in.)
†
Four belts shipped with unit. Use correct set of 2 belts sized according to the pulley setting.
Table 9B -- Medium--Static Drive Data, 60 Hz — English
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
Motor Pulley Pitch Diameter (in.)
4.3--- 5.3
4.3--- 5.3
4.3--- 5.3
3.0
3.0
3.0
MOTOR DRIVE
Pulley Factory Setting
Full Turns Open
FAN DRIVE
Pulley Pitch Dia (in.)
9.4
9.4
9.4
Pulley Bore (in.)
17/16
115/16
115/16
Belt No. — Section
1—B
2—B†
2—B†
Belt Pitch (in.)
41.8
(2) 38.8
(2) 39.8
(2) 38.8
(2) 39.8
881
881
881
798--- 984
798--- 984
798--- 984
Max Allowable Speed (rpm)
1200
1100
1100
Change per 1/2 Turn of
Moveable Motor Pulley
Flange
15.3
15.3
15.3
6
6
6
9.16--- 10.99
6.67--- 9.43
6.67--- 9.43
FAN SPEEDS (rpm)
Factory Setting
Range
MAX FULL TURNS FROM
CLOSED POSITION
SHAFTS CENTER DISTANCE (in.)
†
Four belts shipped with unit. Use correct set of 2 belts sized according to the pulley setting.
29
40RU
FAN SPEEDS (rpm)
Table 9C -- High--Static Drive Data, 60 Hz — English
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
4.3--- 5.3
4.3--- 5.3
4.3--- 5.3
3.0
3.0
3.0
MOTOR DRIVE
Motor Pulley Pitch Diameter (in.)
Pulley Factory Setting
Full Turns Open
FAN DRIVE
Pulley Pitch Dia (in.)
7.4
8.6
8.6
Pulley Bore (in.)
17/16
115/16
115/16
Belt No. — Section
2—B
2—B
2—B
Belt Pitch (in.)
36.8
378
37.8
FAN SPEEDS (rpm)
40RU
Factory Setting
Range
Max Allowable Speed (rpm)
1/
2
Change per
Turn of
Moveable Motor Pulley
Flange
1118
1024
1024
1014--- 1200†
873--- 1075
873--- 1075
1200
1100
1100
19.4
16.7
16.7
6
6
6
8.16--- 10.02
6.67--- 9.43
6.67--- 9.43
MAX FULL TURNS FROM
CLOSED POSITION
SHAFTS CENTER DISTANCE (in.)
† It
is possible to adjust drive so that fan speed exceeds maximum allowable. DO NOT exceed 1200 rpm.
Table 9D-- Standard Drive Data, 60 Hz — SI
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
Motor Pulley Pitch Diameter (mm)
94.0--- 119.4
109.2--- 134.6
109.2--- 134.6
3.0
3.0
3.0
Pulley Pitch Dia (mm)
239
279
279
Pulley Bore (mm)
36.5
49.2
49.2
Belt No. — Section
2—B
2—B†
2—B†
Belt Pitch (mm)
1062
(2) 1987
(2) 1113
(2) 1987
(2) 1113
12.9
12.5
12.5
11.3--- 14.4
11.4--- 14.0
11.2--- 13.9
20.0
18.3
18.3
0.255
0.218
0.218
6
6
6
232--- 279
169--- 240
169--- 240
MOTOR DRIVE
Pulley Factory Setting
Full Turns Open
FAN DRIVE
FAN SPEEDS (r/s)
Factory Setting
Range
Max Allowable Speed (r/s)
1/ Turn
2
Change per
of
Moveable Motor Pulley
Flange
MAX FULL TURNS FROM
CLOSED POSITION
SHAFTS CENTER DISTANCE (mm)
†
Four belts shipped with unit. Use correct set of 2 belts sized according to the pulley setting.
30
Table 9E -- Medium--Static Drive Data, 60 Hz — SI
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
109.2--- 134.6
109.2--- 134.6
109.2--- 134.6
3.0
3.0
3.0
MOTOR DRIVE
Motor Pulley Pitch Diameter (mm)
Pulley Factory Setting
Full Turns Open
FAN DRIVE
Pulley Pitch Dia (mm)
239
239
239
Pulley Bore (mm)
36.5
49.2
49.2
Belt No. — Section
1—B
2—B†
2—B†
Belt Pitch (mm)
1062
(2) 986
(2) 1011
(2) 986
(2) 1011
14.7
14.7
14.7
13.3--- 16.4
13.3--- 16.4
13.3--- 16.4
20.0
18.3
18.3
0.255
0.255
0.255
6
6
6
232--- 279
169--- 240
169--- 240
Factory Setting
Range
Max Allowable Speed (r/s)
1/ Turn
2
Change per
of
Moveable Motor Pulley
Flange
MAX FULL TURNS FROM
CLOSED POSITION
SHAFTS CENTER DISTANCE (mm)
†
Four belts shipped with unit. Use correct set of 2 belts sized according to the pulley setting.
Table 9F -- High--Static Drive Data, 60 Hz — SI
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
Motor Pulley Pitch Diameter (mm)
109.2--- 134.6
109.2--- 134.6
109.2--- 134.6
3.0
3.0
3.0
Pulley Pitch Dia (mm)
188
203†
203
Pulley Bore (mm)
36.5
49.2
49.2
Belt No. — Section
2—B
2—B
2—B
Belt Pitch (mm)
935
935
960
18.6
17.1
17.1
16.9--- 20.0†
14.6--- 17.9
14.6--- 7.9
20.0
18.3
18.3
0.323
0.278
0.278
6
6
6
207--- 255
169--- 240
169--- 240
MOTOR DRIVE
Pulley Factory Setting
Full Turns Open
FAN DRIVE
FAN SPEEDS (r/s)
Factory Setting
Range
Max Allowable Speed (r/s)
1/
2
Change per
Turn of
Moveable Motor Pulley
Flange
MAX FULL TURNS FROM
CLOSED POSITION
SHAFTS CENTER DISTANCE (mm)
† It
is possible to adjust drive so that fan speed exceeds maximum allowable. DO NOT exceed 20 r/s
31
40RU
FAN SPEEDS (r/s)
Table 10A -- 40RU Standard Fan Performance Data —
0.0--2.4 in. wg External Static Pressure — English
EXTERNAL STATIC PRESSURE (in. wg)
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RU
40RUA*28
40RUS*28
40RUA*30
40RUS*30
AIRFLOW
(Cfm)
0.0
0.2
0.4
0.6
0.8
1.0
1.2
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
6,000
532
1.25
569
1.39
639
1.69
711
2.06
781
2.48
846
2.93
905
3.60
7,000
608
1.93
641
2.09
702
2.42
763
2.08
824
3.23
885
3.71
943
4.23
8,000
686
2.83
716
3.01
770
3.38
823
3.77
876
4.21
930
4.70
983
5.24
9,000
764
3.97
791
4.18
841
4.59
888
5.02
935
5.47
982
5.96
1030
6.51
10,000
843
5.38
868
5.62
914
6.09
957
6.55
1000
7.02
1042
7.53
1084
8.08
7,500
456
1.29
490
1.47
556
1.85
621
2.25
678
2.64
729
3.06
778
3.60
8,750
521
1.98
551
2.18
608
2.61
664
3.07
720
3.53
770
3.99
816
4.45
10,000
587
2.88
614
3.11
664
3.59
714
4.09
763
4.62
812
5.15
857
5.68
11,250
653
4.03
678
4.29
724
4.82
768
5.37
812
5.95
856
6.54
899
7.14
12,500
720
5.46
743
5.75
785
6.33
825
6.93
865
7.55
904
8.20
944
8.86
15,000
829
8.84
850
9.19
888
9.88
924
10.57
958
11.27
991
11.99
1024
12.73
9,000
521
1.99
550
2.25
616
2.77
676
3.23
731
3.72
782
4.20
829
4.70
10,500
596
3.16
623
3.40
672
3.89
720
4.40
767
4.94
814
5.50
859
6.05
12,000
673
4.63
698
4.90
743
5.45
785
6.02
826
6.62
867
7.23
908
7.87
13,500
751
6.51
773
6.82
815
7.44
853
8.06
890
8.71
927
9.38
963
10.07
15,000
829
8.84
850
9.19
888
9.88
924
10.57
958
11.27
991
11.99
1024
12.73
See Legend and Notes on page 36.
Table 10A -- 40RU Standard Fan Performance Data —
0.0--2.4 in. wg External Static Pressure — English (cont)
EXTERNAL STATIC PRESSURE (in. wg)
UNIT
AIRFLOW
(Cfm)
40RUA*28
40RUS*28
40RUA*30
40RUS*30
1.6
1.8
2.0
2.2
2.4
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
954
3.83
1005
4.27
1052
4.72
1098
5.22
1142
5.67
—
—
7,000
990
4.74
1040
5.24
1090
5.80
1135
6.30
1176
6.84
—
—
8,000
1028
5.79
1078
6.38
1130
7.00
1173
7.60
—
—
—
—
6,000
40RUA*25
40RUQ*25
40RUS*25
1.4
Rpm
9,000
1073
7.11
1120
7.72
1169
8.37
—
—
—
—
—
—
10,000
1126
8.75
1166
9.37
—
—
—
—
—
—
—
—
7,500
831
4.41
870
5.10
913
5.90
950
6.88
985
7.70
—
—
8,750
859
4.97
901
5.59
944
6.42
980
7.20
1020
8.10
—
—
10,000
900
6.20
939
6.74
976
7.33
1013
8.00
1050
8.82
—
—
11,250
941
7.73
980
8.32
1017
8.90
1052
9.51
1088
10.16
—
—
—
12,500
984
9.53
1022
10.19
1058
10.84
1093
11.49
—
—
—
15,000
1057
13.49
1090
14.28
—
—
—
—
—
—
—
—
9,000
866
5.20
899
5.85
950
6.65
989
7.38
1029
8.32
1077
9.74
10,500
902
6.60
942
7.14
980
7.70
1016
8.31
1051
8.99
1085
9.77
12,000
949
8.50
988
9.14
1026
9.76
1062
10.38
1095
11.01
—
—
13,500
1000
10.78
1036
11.49
1073
12.21
—
—
—
—
—
—
15,000
1057
13.49
1090
14.28
—
—
—
—
—
—
—
—
See Legend and Notes on page 36.
32
Table 10B -- 40RU Standard Fan Performance Data —
0--600 kPa External Static Pressure — SI
EXTERNAL STATIC PRESSURE (kPa)
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
0
50
100
150
200
250
300
r/s
kW
r/s
kW
r/s
kW
r/s
kW
r/s
kW
r/s
kW
r/s
kW
2830
8.86
0.94
9.48
1.04
10.65
1.26
11.84
1.53
13.01
1.85
14.10
2.19
15.08
2.53
3300
10.14
1.44
10.69
1.56
11.70
1.81
12.71
2.08
13.73
2.41
14.74
2.77
15.71
3.15
3780
11.43
2.11
11.93
2.25
12.84
2.52
13.71
2.81
14.60
3.14
15.49
3.51
16.39
3.91
4250
12.74
2.96
13.19
3.12
14.02
3.43
14.81
3.74
15.59
4.08
16.37
4.45
17.17
4.85
4720
14.05
4.01
14.47
4.19
15.23
4.54
15.96
4.88
16.66
5.24
17.36
5.62
18.07
6.03
3540
7.60
0.96
8.16
1.09
9.27
1.38
10.34
1.68
11.30
1.97
12.15
2.28
12.97
2.68
4130
8.68
1.47
9.18
1.62
10.13
1.94
11.07
2.29
11.99
2.63
12.84
2.97
13.60
3.32
4720
9.78
2.15
10.23
2.32
11.07
2.67
11.89
3.05
12.72
3.45
13.53
3.84
14.29
4.23
5310
10.89
3.01
11.30
3.20
12.06
3.59
12.80
4.00
13.53
4.43
14.27
4.88
14.99
5.33
5900
12.00
4.07
12.38
4.29
13.09
4.72
13.75
5.17
14.41
5.63
15.07
6.11
15.74
6.61
4250
8.68
1.48
9.17
1.68
10.27
2.07
11.27
2.41
12.19
2.77
13.03
3.13
13.81
3.50
4960
9.93
2.35
10.38
2.53
11.21
2.90
11.99
3.28
12.78
3.68
13.56
4.10
14.32
4.51
5660
11.21
3.45
11.63
3.66
12.38
4.07
13.08
4.49
13.76
4.93
14.45
5.39
15.14
5.87
6370
12.51
4.85
12.89
5.08
13.58
5.54
14.22
6.01
14.83
6.49
15.44
6.99
16.05
7.51
7080
13.82
6.59
14.17
6.85
14.81
7.36
15.40
7.88
15.97
8.40
16.52
8.94
17.06
9.49
See Legend and Notes on page 36.
Table 10B -- 40RU Standard Fan Performance Data —
0--600 kPa External Static Pressure — SI (cont)
EXTERNAL STATIC PRESSURE (kPa)
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
AIRFLOW
(L/s)
350
400
450
500
550
600
r/s
kW
r/s
kW
r/s
kW
r/s
kW
r/s
kW
r/s
kW
2830
15.90
2.86
16.75
3.18
17.53
3.52
18.30
3.89
19.03
4.23
—
—
3300
16.50
3.53
17.33
3.91
18.17
4.32
18.92
4.70
19.60
5.10
—
—
3780
17.13
4.32
17.97
4.76
18.83
5.22
19.55
5.67
—
—
—
—
4250
17.88
5.30
18.67
5.76
19.48
6.24
—
—
—
—
—
—
4720
18.77
6.52
19.43
6.99
—
—
—
—
—
—
—
—
3540
13.85
3.29
14.50
3.80
15.22
4.40
15.83
5.13
16.42
5.74
—
—
4130
14.31
3.71
15.01
4.17
15.74
4.79
16.33
5.37
17.00
6.04
—
—
4720
14.99
4.62
15.65
5.02
16.27
5.46
16.88
5.97
17.50
6.57
—
—
5310
15.68
5.77
16.34
6.20
16.95
6.64
17.53
7.09
18.09
7.58
—
—
5900
16.39
7.10
17.03
7.60
17.64
8.08
18.22
8.57
—
—
—
—
4250
14.43
3.88
14.98
4.36
15.84
4.96
16.48
5.50
17.16
6.21
17.96
7.26
4960
15.04
4.92
15.71
5.32
16.33
5.74
16.93
6.20
17.51
6.70
18.09
7.29
5660
15.81
6.34
16.47
6.81
17.10
7.28
17.69
7.74
18.26
8.21
—
—
6370
16.66
8.04
17.27
8.57
17.88
9.10
—
—
—
—
—
—
7080
17.61
10.06
18.16
10.64
—
—
—
—
—
—
—
—
See Legend and Notes on page 36.
33
40RU
UNIT
AIRFLOW
(L/s)
Table 10C -- 40RU High--Capacity Fan Performance Data —
0.0--2.4 in. wg External Static Pressure — English
EXTERNAL STATIC PRESSURE (in. wg)
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RU
40RUA*28
40RUS*28
40RUA*30
40RUS*30
AIRFLOW
(Cfm)
0.0
0.2
0.4
0.6
0.8
1.0
1.2
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
6,000
542
1.29
577
1042
646
1.72
716
2.09
785
2.51
849
2.95
907
3.40
7,000
620
1.99
652
2.15
711
2.48
771
2.85
831
3.28
890
3.76
947
4.27
8,000
700
2.92
728
3.10
781
3.46
833
3.85
885
4.29
938
4.78
990
5.32
9,000
781
4.10
806
4.30
854
4.71
900
5.13
946
5.58
993
6.08
1039
6.62
10,000
862
5.56
885
5.79
929
6.24
971
6.70
1012
7.18
1054
7.69
1096
8.24
7,500
476
1.39
510
1.58
579
1.99
644
2.40
701
2.81
752
3.29
804
3.96
8,750
545
2.14
574
2.35
633
2.81
691
3.29
747
3.77
797
4.25
842
4.76
10,000
615
3.12
641
3.36
692
3.87
743
4.41
794
4.96
843
5.51
888
6.05
11,250
685
4.37
709
4.64
754
5.20
800
5.79
845
6.40
891
7.02
935
7.64
12,500
756
5.92
778
6.22
819
6.83
860
7.47
901
8.14
942
8.83
983
9.52
9,000
539
2.18
569
2.39
626
2.85
683
3.34
739
3.83
791
4.32
837
4.82
10,500
620
3.37
646
3.62
695
4.13
744
4.68
793
5.25
842
5.83
888
6.41
12,000
701
4.94
724
5.22
769
5.80
811
6.40
854
7.04
897
7.69
940
8.36
13,500
783
6.95
804
7.27
844
7.91
883
8.57
920
9.26
958
9.97
996
10.71
15,000
865
9.45
884
9.81
921
10.52
956
11.24
991
11.98
1025
12.75
1059
13.54
See Legend and Notes on page 36.
Table 10C -- 40RU High--Capacity Fan Performance Data —
0.0--2.4 in. wg External Static Pressure — English (cont)
EXTERNAL STATIC PRESSURE (in. wg)
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
AIRFLOW
(Cfm)
1.4
1.6
1.8
2.0
2.2
2.4
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
Rpm
Bhp
6,000
961
3.86
1011
4.31
1058
4.77
1104
5.24
1147
5.71
—
—
7,000
1000
4.79
1050
5.32
1097
5.85
1142
6.38
1184
6.91
—
—
8,000
1041
5.88
1090
6.47
1137
7.07
1181
7.67
—
—
—
—
9,000
1086
7.21
1133
7.82
1178
8.47
—
—
—
—
—
—
10,000
1138
8.83
1180
9.46
—
—
—
—
—
—
—
—
7,500
874
5.33
897
5.91
940
6.80
990
7.50
—
—
—
—
8,750
886
5.36
930
6.13
982
7.32
1020
8.10
—
—
—
—
10,000
930
6.60
969
7.20
1007
7.89
1045
8.71
—
—
—
—
11,250
976
8.25
1014
8.86
1051
9.49
1086
10.17
—
—
—
—
12,500
1023
10.20
1061
10.88
1097
11.56
—
—
—
—
—
—
9,000
881
5.37
923
6.03
967
6.89
1020
8.25
—
—
—
—
10,500
930
6.97
970
7.55
1008
8.17
1045
8.86
—
—
—
—
12,000
981
9.02
1021
9.67
1058
10.32
1094
10.97
—
—
—
—
13,500
1035
11.45
1072
12.20
—
—
—
—
—
—
—
—
15,000
1093
14.35
—
—
—
—
—
—
—
—
—
—
See Legend and Notes on page 36.
34
Table 10D -- 40RU High--Capacity Fan Performance Data —
0--600 kPa External Static Pressure — SI
EXTERNAL STATIC PRESSURE (kPa)
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
0
50
100
150
200
250
300
r/s
kW
r/s
kW
r/s
kW
r/s
kW
r/s
kW
r/s
kW
r/s
kW
2830
9.03
0.96
9.62
1.06
10.77
1.29
11.94
1.56
13.08
1087
14.15
2.20
15.12
2.54
3330
10.34
1.48
10.86
1.60
11.85
1.85
12.84
2.12
13.85
2.45
14.84
2.80
15.78
3.18
3780
11.67
2.17
12.14
2.31
13.02
2.58
13.88
2.87
14.75
3.20
15.63
3.56
16.50
3.96
4250
13.01
3.05
13.44
3.21
14.23
3.51
15.00
3.82
15.77
4.16
16.54
4.53
17.32
4.94
4720
14.36
4.15
14.75
4.32
15.48
4.66
16.18
4.99
16.87
5.35
17.56
5.73
18.26
6.14
3540
7.94
1.04
8.51
1.18
9.65
1.48
10.73
1.79
11.68
2.10
12.53
2.46
13.40
2.95
4130
9.08
1.59
9.57
1.75
10.55
2.10
11.52
2.46
12.45
2.81
13.28
3.17
14.04
3.55
4720
10.24
2.33
10.68
2.51
11.53
2.88
12.39
3.29
13.24
3.70
14.05
4.11
14.80
4.51
5310
11.42
3.26
11.81
3.46
12.57
3.88
13.33
4.32
14.09
4.77
14.85
5.24
15.58
570
5900
12.60
4.42
12.96
4.64
13.65
5.09
14.33
5.57
15.01
6.07
15.40
6.58
16.38
7.10
4250
8.99
1.62
9.49
1.78
10.44
2.12
11.39
2.49
12.32
2.86
13.18
3.22
13.95
3.59
4960
10.33
2.51
10.77
2.70
11.59
3.08
12.40
3.49
13.22
3.92
14.03
4.35
14.79
4.78
5660
11.68
3.68
12.07
3.90
12.81
4.33
13.52
4.77
14.23
5.25
14.95
5.74
15.66
6.23
6370
13.04
5.18
13.40
5.42
14.07
5.90
14.71
6.39
15.34
6.90
15.97
7.44
16.61
7.98
7080
14.42
7.05
14.74
7.31
15.36
7.84
15.94
8.38
16.51
8.93
17.08
9.51
17.65
10.10
See Legend and Notes on page 36.
Table 10D -- 40RU High--Capacity Fan Performance Data —
0--600 kPa External Static Pressure — SI (cont)
EXTERNAL STATIC PRESSURE (kPa)
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
AIRFLOW
(L/s)
350
400
450
500
550
600
r/s
kW
r/s
kW
r/s
kW
r/s
kW
r/s
kW
r/s
kW
2830
16.01
2.88
16.85
3.22
17.64
3.56
18.39
3.91
19.12
4.26
—
—
3300
16.67
3.57
17.50
3.96
18.28
4.36
19.03
4.75
19.73
5.15
—
—
3780
17.35
4.39
18.17
4.82
18.95
5.27
19.68
5.72
—
—
—
—
4250
18.11
5.37
18.88
5.83
19.63
6.31
—
—
—
—
—
—
4720
18.96
6.58
19.67
7.05
—
—
—
—
—
—
—
—
3540
14.57
3.97
14.95
4.41
15.67
5.07
16.50
5.59
—
—
—
—
4130
14.76
3.99
15.51
4.57
16.36
5.46
17.00
6.04
—
—
—
—
4720
15.49
4.92
16.15
5.37
16.78
5.88
17.42
6.50
—
—
—
—
5310
16.26
6.15
16.91
6.61
17.51
7.08
18.10
7.58
—
—
—
—
5900
17.04
7.61
17.68
8.11
18.28
8.62
—
—
—
—
—
—
4250
14.68
4.00
15.38
4.49
16.12
5.14
17.00
6.15
—
—
—
—
4960
15.51
5.20
16.17
5.63
16.80
6.09
17.41
6.61
—
—
—
—
5660
16.35
6.72
17.01
7.21
17.64
7.69
18.23
8.18
—
—
—
—
6370
17.24
8.54
17.87
9.10
—
—
—
—
—
—
—
—
7080
18.22
10.70
—
—
—
—
—
—
—
—
—
—
See Legend and Notes on page 36.
35
40RU
UNIT
AIRFLOW
(L/s)
Legend and Notes for Tables 10A and 10C
40RU
LEGEND
Bhp --- Brake Horsepower Input to Fan
ESP --- External Static Pressure
NOTES:
1. Maximum allowable fan speed for size 25 units is 1200 rpm . Maximum
allowable fan speed for size 28 and 30 units is 1100 rpm.
2. Fan performance is based on deductions for wet coil, clean 2-in. filters,
and unit casing. See table at right for factory-supplied filter pressure drop.
3. Refer to fan motor and drive tables for additional data.
FACTORY-SUPPLIED PRESSURE DROP — ENGLISH
UNIT
40RUA*25
40RUQ*25
40RUS*25
AIRFLOW
(Cfm)
PRESSURE DROP
(in. wg)
6,000
0.12
8,000
0.19
10,000
0.26
7,500
0.15
40RUA*28
40RUS*28
10,000
0.22
12,500
0.30
9,000
0.19
40RUA*30
40RUS*30
12,000
0.29
15,000
0.40
Legend and Notes for Tables 10B and 10D
LEGEND
ESP --- External Static Pressure
NOTES:
1. Maximum allowable fan speed for size 25 units is 20 r/s. Maximum
allowable fan speed for size 28 and 30 units is 18.3 r/s.
2. Fan performance is based on deductions for wet coil, clean 51 ---mm
filters, and unit casing. See table at right for factory-supplied filter
pressure drop.
3. Refer to fan motor and drive tables for additional data.
FACTORY-SUPPLIED PRESSURE DROP — SI
UNIT
40RUA*25
40RUQ*25
40RUS*25
40RUA*28
40RUS*28
40RUA*30
40RUS*30
36
AIRFLOW
(L/s)
PRESSURE DROP
(Pa)
2900
32
3800
47
4700
64
3500
36
4700
55
5900
76
4250
47
5650
71
7050
98
37
40RU
40RU
Copyright 2011 Carrier Corp. D 7310 W. Morris St. D Indianapolis, IN 46231
Printed in U.S.A.
Edition Date: 01/11
Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.
38
Catalog No: 40RU ---07SI
Replaces: 40RU--- 05SI
START--UP CHECKLIST
(SPLIT SYSTEMS WITH 40RU UNITS)
I. PRELIMINARY INFORMATION
OUTDOOR: MODEL NO.
INDOOR: MODEL NO.
SERIAL NO.
SERIAL NO.
ADDITIONAL ACCESSORIES
II. PRE--START--UP
OUTDOOR UNIT
IS THERE ANY SHIPPING DAMAGE? (Y/N)
WILL THIS DAMAGE PREVENT UNIT START-- UP? (Y/N)
CHECK POWER SUPPLY. DOES IT AGREE WITH UNIT? (Y/N)
HAS THE GROUND WIRE BEEN CONNECTED? (Y/N)
HAS THE CIRCUIT PROTECTION BEEN SIZED AND INSTALLED PROPERLY? (Y/N)
ARE THE POWER WIRES TO THE UNIT SIZED AND INSTALLED PROPERLY? (Y/N)
HAVE COMPRESSOR HOLDDOWN BOLTS BEEN LOOSENED? (Y/N)
CONTROLS
ARE THERMOSTAT(S) & INDOOR FAN CONTROL WIRING CONNECTIONS MADE & CHECKED? (Y/N)
ARE ALL WIRING TERMINALS (including main power supply) TIGHT? (Y/N)
HAVE OUTDOOR UNIT CRANKCASE HEATERS BEEN ENERGIZED FOR 24 HOURS? (Y/N)
INDOOR UNIT
HAS WATER BEEN PLACED IN DRAIN PAN TO CONFIRM PROPER DRAINAGE? (Y/N)
ARE PROPER AIR FILTERS IN PLACE? (Y/N)
HAVE FAN AND MOTOR PULLEYS BEEN CHECKED FOR PROPER ALIGNMENT? (Y/N)
DO THE FAN BELTS HAVE PROPER TENSION? (Y/N)
PIPING
40RUA, 40RUQ
HAS FOAM SHIPPING BLOCK BEEN REMOVED FROM THE TXV (Thermostatic Expansion Valve)? (Y/N)
ARE LIQUID LINE SOLENOID VALVES LOCATED AT THE INDOOR UNIT (40RUA) OR OUTDOOR UINT
(40RUQ) COILS AS REQUIRED? (Y/N)
HAVE LEAK CHECKS BEEN MADE AT COMPRESSORS, CONDENSERS, INDOOR COILS,
TXVs (Thermostatic Expansion Valves) SOLENOID VALVES, FILTER DRIERS, AND FUSIBLE PLUGS
WITH A LEAK DETECTOR? (Y/N)
LOCATE, REPAIR, AND REPORT ANY LEAKS
HAVE ALL COMPRESSOR SERVICE VALVES BEEN FULLY OPENED (BACKSEATED) (Y/N)
ARE THE COMPRESSOR OIL SIGHT GLASSES SHOWING CORRECT LEVELS? (Y/N)
40RUS
HAS AIR BEEN BLED FROM SYSTEM? (Y/N)
HAVE LEAK CHECKS BEEN MADE AT COMPRESSORS, CHILLERS, VALVES, & INDOOR COILS? (Y/N)
LOCATE, REPAIR, AND REPORT ANY LEAKS.
39
40RU
IF SO, WHERE:
CHECK VOLTAGE IMBALANCE
LINE-TO-LINE VOLTS:
AB
V
AC
V
(AB + AC + BC)/3 = AVERAGE VOLTAGE =
BC
V
V
MAXIMUM DEVIATION FROM AVERAGE VOLTAGE =
V
VOLTAGE IMBALANCE = 100 X (MAX DEVIATION)/(AVERAGE VOLTAGE) =
IF OVER 2% VOLTAGE IMBALANCE, DO NOT ATTEMPT TO START SYSTEM!
CALL LOCAL POWER COMPANY FOR ASSISTANCE.
III. START--UP
CHECK INDOOR FAN MOTOR SPEED AND RECORD.
AFTER AT LEAST 10 MINUTES RUNNING TIME, RECORD THE FOLLOWING MEASUREMENTS:
40RU
COMP A1
COMP B1
OIL PRESSURE
SUCTION PRESSURE
SUCTION LINE TEMP
DISCHARGE PRESSURE
DISCHARGE LINE TEMP
ENTERING OUTDOOR UNIT AIR TEMP
LEAVING OUTDOOR UNIT AIR TEMP
INDOOR UNIT ENTERING AIR DB TEMP
INDOOR UNIT ENTERING AIR WB TEMP
INDOOR UNIT LEAVING AIR DB TEMP
INDOOR UNIT LEAVING AIR WB TEMP
OUTDOOR UNIT ENTERING WATER TEMP
(40RUS ONLY)
OUTDOOR UNIT LEAVING WATER TEMP
(40RUS ONLY)
INDOOR UNIT ENTERING WATER TEMP
(40RUS ONLY)
INTDOOR UNIT LEAVING WATER TEMP
(40RUS ONLY)
COMPRESSOR AMPS (L1/L2/L3)
____/____/____
____/____/____
CHECK THE COMPRESSOR OIL LEVEL SIGHT GLASSES, ARE THE SIGHT GLASSES SHOWING
OIL LEVEL AT 1/8 to 1/3 FULL? (Y/N)
NOTES:
Copyright 2011 Carrier Corp. D 7310 W. Morris St. D Indianapolis, IN 46231
Printed in U.S.A.
Edition Date:01/11
Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.
40
Catalog No: 40RU ---07SI
Replaces: 40RU--- 05SI
Download PDF

advertising