User manual | Carrier Access none Network Router User Manual

Adit 3000 Series and
Multi-Service Router (MSR) Card
CLI REFERENCE MANUAL
Part Number: 770-0165 BB
Product Release: Adit 3000 Series - 1.6
MSR Card - 2.0
April 2008
Copyright 2008 Turin Networks Inc. All rights reserved.
The information presented in this manual is subject to change without notice and does not represent a commitment on the
part of Turin Networks Inc. The hardware and software described herein are furnished under a license or non-disclosure
agreement. The hardware, software, and manual may be used or copied only in accordance with the terms of this agreement.
It is against the law to reproduce, transmit, transcribe, store in a retrieval system, or translate into any medium - electronic,
mechanical, magnetic, optical, chemical, manual, or otherwise - any part of this manual or software supplied with the Adit
3000 series or MSR products for any purpose other than the purchaser’s personal use without the express written
permission of Turin Networks Inc.
The Turin Networks logo and Adit are registered trademarks of Turin Networks Inc. All other brand or product names are
trademarks or registration trademarks of their respective companies or organizations.
Corporate Contact Information:
Turin Networks
1415 North McDowell Blvd.
Petaluma, CA 94954
Phone: +1-707-665-4400
Fax: +1-707-793-4935
www.TurinNetworks.com
Customer Support:
E-mail: tech-support@TurinNetworks.com
Phone: 800-786-9929 or 303-218-5655
Supporting Software Versions:
Adit 3104 - Release 1.6
Adit 3200 - Release 1.6
Adit 3500 - Release 1.6
Multi-Service Router (MSR) Card - Release 2.0
PREFACE
Preface
Safety Information
CAUTION! WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS,
INCLUDING THE FOLLOWING:
z
Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or
laundry tub, in a wet basement or near a swimming pool.
z
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be
a remote risk of electric shock from lightning.
z
Do not use the telephone to report a gas leak in the vicinity of the leak.
z
Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a
fire. They may explode. Check with local codes for possible special disposal instructions.
z
Refer to the installation section of this manual for a safe and proper installation procedure. All
wiring external to this equipment should follow the current provision of the National Electrical
Code
NOTE: For Safety and Compliance information for the Multi-Service Router (MSR) card and
Adit 600 platform, please refer to the Adit 600 User Manual.
Preface
Notices
This manual contains important information and warnings that must be followed to ensure safe
operation of the equipment.
DANGER! A DANGER NOTICE INDICATES THE PRESENCE OF A HAZARD THAT CAN OR WILL
CAUSE DEATH OR SEVERE PERSONAL INJURY IF THE HAZARD IS NOT AVOIDED.
CAUTION! A CAUTION NOTICE INDICATES THE POSSIBILITY OF INTERRUPTING NETWORK
SERVICE IF THE HAZARD IS NOT AVOIDED.
WARNING! A WARNING NOTICE INDICATES THE POSSIBILITY OF EQUIPMENT DAMAGE IF THE
HAZARD IS NOT AVOIDED.
NOTE: A Note indicates information to help you understand how to perform a procedure or how the
system works. Notes should be read before performing the required action.
iv
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
TABLE OF CONTENTS
Table of Contents
Preface
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
1
Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Prompt Identifier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
User Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Privileged Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Command Syntax Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Command Line Interface Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Shortcuts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
2
User Mode
date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33
3
Privileged Mode
clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
configure terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
debug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
log clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
no debug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
Table of Contents
reload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
3-18
3-19
3-67
3-67
Global Configuration Mode
Commands for Entering Configuration Submodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Global Configuration Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
access-control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
access-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
authentication login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
clock source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
controller lcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
controller t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
delete local-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
dial-peer voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
dmz-host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
dynamic-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
host-filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
interface ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
interface multilink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
interface serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
ip dhcp pool ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
ip domain-name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
ip host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
l2tpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
local-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27
log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
mail-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33
nat-bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35
network-object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36
port-trigger service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53
pptpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53
pptps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53
radius-client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-54
vi
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Table of Contents
remote-admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-54
router ospf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-56
security-default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-57
security-log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-58
service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-59
snmp-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60
static-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-62
time-range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-62
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-63
vlan (global) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-63
vlan (vlan-id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-64
voice-codec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-64
voice-port (global) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65
voice-port fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65
voice-port trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-66
voice-service sip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-66
5
Configuration - LCC Controller Mode
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
no command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
6
Configuration - T1 Controller Mode
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
ds0-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
fdl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
framing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
idle-pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
lbo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
linecode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
loopdetect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
pri-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
tdm-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
vii
Table of Contents
7
Configuration - DHCP Pool Ethernet Mode
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
end-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
start-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
static-lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
subnet-mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
wins server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
7-2
7-3
7-3
7-3
7-4
7-4
7-5
7-6
7-6
7-7
7-7
7-8
7-8
Configuration - Dial Peer FXS Mode
block-out-caller-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
call-wait-caller-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
call-waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
calling-party-disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
codec preference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
destination-pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
fax-protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
modem-protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
sip-authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
9
Configuration - Dial Peer Trunk Mode
codec preference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
destination-pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
fax-protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
modem-protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
sip-authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
strip-digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
viii
9-2
9-2
9-3
9-4
9-4
9-4
9-5
9-5
9-6
9-7
9-7
9-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Table of Contents
10
Configuration - Dial Peer VoIP Mode
destination-pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5
prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
session-target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
strip-digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
user-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
11
Configuration - Ethernet Interface Mode
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4
full-duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5
half-duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6
ip default-gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
ip dhcp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8
ip ospf authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-9
ip ospf authentication-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-10
ip ospf cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-10
ip ospf dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-10
ip ospf disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-11
ip ospf hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-11
ip ospf message-digest-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-11
ip ospf priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
ip ospf retransmit-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
ip ospf transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13
ip proxy-arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13
ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-15
ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-15
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-16
metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-16
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-17
release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-23
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
ix
Table of Contents
remote-admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
renew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
schedule-availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
tos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
11-23
11-23
11-24
11-24
11-24
11-25
11-25
Configuration - Multilink Interface Mode
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6
ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6
ip ospf authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7
ip ospf authentication-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-8
ip ospf cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-8
ip ospf dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-8
ip ospf disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-9
ip ospf hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-9
ip ospf message-digest-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-9
ip ospf priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-10
ip ospf retransmit-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-10
ip ospf transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-10
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-11
ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-11
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-12
ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13
metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-14
ppp authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-21
ppp encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-21
ppp exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-21
ppp link-fragmentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-22
ppp on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-22
ppp password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-22
ppp qos-interleaving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-23
ppp restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-23
ppp time-btwn-reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-23
x
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Table of Contents
ppp username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-24
schedule-availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-24
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-24
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-25
13
Configuration - Serial Interface Mode
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3
encapsulation ppp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6
ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6
ip ospf authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-7
ip ospf authentication-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-8
ip ospf cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-8
ip ospf dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-8
ip ospf disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-9
ip ospf hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-9
ip ospf message-digest-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-9
ip ospf priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-10
ip ospf retransmit-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-10
ip ospf transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-10
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-11
ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-11
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-12
ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-13
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-13
metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-13
multilink-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14
ppp authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-21
ppp encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-21
ppp exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-21
ppp link-fragmentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-22
ppp on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-22
ppp password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-22
ppp restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-23
ppp time-btwn-reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-23
ppp username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-23
schedule-availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-24
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
xi
Table of Contents
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-24
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-24
14
Configuration - IPSec Mode
aggressive-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2
authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-3
dpd-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4
dpd-enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4
dpd-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-5
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-5
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-5
group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-6
hash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-6
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-7
ip route metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-7
ipsec-conn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-8
ipsec-manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-8
key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-8
lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-9
local-subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-9
max-retries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-10
mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-10
net-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-11
netbios remote-brc-addr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-11
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-12
reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-17
rekey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-17
remote-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-17
remote-subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-18
schedule-availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-18
session-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-19
set-pfs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-19
transform-set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-20
Example of IPSec Connection Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-21
xii
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Table of Contents
15
Configuration - L2TPC Mode
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-2
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4
host-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5
ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5
ip ospf authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-6
ip ospf authentication-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7
ip ospf cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7
ip ospf dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7
ip ospf disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-8
ip ospf hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-8
ip ospf message-digest-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-8
ip ospf priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-9
ip ospf retransmit-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-9
ip ospf transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-9
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-10
ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-10
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-11
ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-12
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-12
local-secret . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-12
metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-13
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-13
ppp authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-21
ppp encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-21
ppp exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-21
ppp on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-22
ppp password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-22
ppp restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-22
ppp time-btwn-reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-23
ppp username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-23
schedule-availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-23
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-24
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-24
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
xiii
Table of Contents
16
Configuration - OSPF Mode
area commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-2
compatible rfc1583 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-3
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-4
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-5
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-5
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-5
network area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-6
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-7
router-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-9
Sample Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-10
17
Configuration - PPTPC Mode
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-2
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-3
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-3
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-3
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-4
host-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-4
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-5
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-5
ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-5
ip ospf authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-6
ip ospf authentication-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-7
ip ospf cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-7
ip ospf dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-7
ip ospf disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-8
ip ospf hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-8
ip ospf message-digest-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-8
ip ospf priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-9
ip ospf retransmit-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-9
ip ospf transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-9
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-10
ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-10
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-11
ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-12
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-12
metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-12
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-13
ppp authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-20
ppp encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-20
ppp exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-21
ppp on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-21
ppp password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-21
xiv
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Table of Contents
ppp restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-22
ppp time-btwn-reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-22
ppp username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-22
schedule-availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-23
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-23
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-23
18
Configuration - PPTPS Mode
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-2
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-3
end-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-3
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-3
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-4
idle-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-4
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-5
ppp authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-6
ppp encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-6
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-7
start-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-7
19
Configuration - RADIUS Mode
authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-2
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-3
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-4
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-4
host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-5
key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-5
20
Configuration - VLAN Mode
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-2
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-3
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-3
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-3
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-4
port-dot1q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-5
port-priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-5
port-protocol-filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-6
pvid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-6
tag-all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-7
vlan-feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-7
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
xv
Table of Contents
21
Configuration - VLAN Port Mode
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
voip-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
Configuration - Voice Port Mode
digit-map (global) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
no digit-map (global) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
tos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
23-2
23-2
23-3
23-4
23-4
23-4
23-5
23-5
23-6
23-7
23-7
23-7
23-8
Configuration - Voice Port Trunk Mode
comfort-noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
connection lcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
connection t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
digit-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
echo-cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xvi
22-2
22-3
22-4
22-4
22-4
22-5
22-5
Configuration - Voice Port FXS Mode
comfort-noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
echo-cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
input-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
output-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
per-line-logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
21-2
21-3
21-3
21-3
21-4
21-4
21-5
21-5
24-2
24-2
24-2
24-3
24-3
24-4
24-5
24-5
24-5
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Table of Contents
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-6
input-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-6
isdn switch-type (PRI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-7
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-8
output-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-11
registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-12
signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-14
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-15
25
Configuration - Voice Service SIP Mode
calling-party-disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-2
conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-2
do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-3
dtmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-4
early-media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-4
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-5
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-5
fax-protocol-t38 ecs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-6
fax-protocol-t38 redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-6
fax-protocol-t38 signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-7
feature-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-7
gateway-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-8
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-8
no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-9
outbound-proxy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-11
phone-number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-11
prack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-11
privacy-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-12
proxy-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-12
proxy-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-13
redundancy advance-retries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-13
redundancy advance-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-14
redundancy filter-incoming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-14
redundancy primary-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-14
redundancy rollback-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-15
redundancy secondary-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-15
redundancy ttl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-16
redundancy type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-16
registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-17
rtp-base-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-17
session-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-18
sip-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-19
transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-19
Index
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
xvii
Table of Contents
xviii
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
1
Introduction
This Reference Manual covers the Command Line Interface (CLI) for the following products:
z Adit 3000 series (Adit 3104, Adit 3200, and Adit 3500)
z Multi-Service Router (MSR) Card (a service card for the Adit 600 platform)
The chapters are broken down into Modes and Configuration Groups. All commands that are
listed in each group are described in the chapter.
NOTE: Throughout this manual, examples primarily reflect the Adit 3000 series. Where
differences exist for the MSR card, these differences are noted.
In this Chapter
„
Overview
„
Command Syntax Conventions
„
Command Line Interface Help
„
Shortcuts
Introduction
Overview
Overview
The Adit 3000/MSR CLI has three command modes, each with access to different command sets. The
following displays the basic flow of the CLI.
1-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Introduction
Overview
Prompt Identifier
When you initiate a CLI session it will open in User mode, which is indicated by the ">" prompt. At any
time you can quickly determine which mode you are in by the prompt.
Command
Mode
Access Method
Prompt Displayed
Exit Method
User
Login
adit 3104>
adit 3200>
adit 3500>
adit MSR>
Use the logout command
Privileged
From User mode, enter the
enable command
adit 3104#
adit 3200#
adit 3500#
adit MSR#
Use the exit or end command.
Global
Configuration
From Privileged mode, enter
the configure terminal
command.
adit 3104 (config)#
adit 3200 (config)#
adit 3500 (config)#
adit MSR (config)#
Use the exit or end command, or
press Ctrl-z.
User Mode
In User Mode, the operator is allowed to view only limited information (not able to modify
configurations). Editing the configuration requires you to be in Privileged mode.
Privileged Mode
Privileged mode requires a password, and allows the operator to enter the Configuration mode.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
1-3
Introduction
Overview
Configuration Mode
z Allows users to configure specific features/functions.
z Use the configure terminal command to enter from Privileged mode.
z Identified by the (config)# prompt.
Note: As the submodes change, the words inside the parentheses are modified.
z To exit Configuration mode, type exit or press Ctrl-Z.
z Configuration mode has various submodes:
1-4
Configuration Mode
Link to Command
Prompt Displayed
Controller LCC
controller lcc
(config-cont-lcc-{n})#
Controller T1
controller t1
(config-cont-t1-{n})#
DHCP server pool
ip dhcp pool ethernet
(config-dhcp-eth-{n})#
Dial Peer FXS
dial-peer voice pots fxs
(config-dpeer-fxs)#
Dial Peer Trunk
dial-peer voice pots trunk
(config-dpeer-trk)#
Dial Peer VoIP
dial-peer voice voip
(config-dpeer-voip)#
Ethernet Interface
interface ethernet
(config-int-eth-{n})#
MLPPP Interface
interface multilink
(config-int-mlink-{n})#
Serial Interface
interface serial
(config-int-ser-{n})#
VPN IPSEC
ipsec
(config-ipsec)#
VPN L2TP Client
l2tpc
(config-l2tpc)#
OSPF
router ospf
(config-ospf)#
VPN PPTP Client
pptpc
(config-pptpc-{n})#
VPN PPTP Server
pptps
(config-pptps)#
RADIUS
radius-client
(config-radius)#
VLAN (Global)
vlan (global)
(config-vlan)#
VLAN (Port)
vlan (vlan-id)
(config-vlan-{n})#
Voice Port (Global)
voice-port (global)
(config-vport)#
Voice Port (FXS)
voice-port fxs
(config-vport-fxs-{n})#
Voice Port (Trunk)
voice-port trunk
(config-vport-trunk-{n})#
Voice Service SIP
voice-service sip
(config-voice-serv-sip)#
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Introduction
Command Syntax Conventions
Command Syntax Conventions
The conventions used to present command syntax are as follows:
Convention
Description
|
Vertical bars separate alternative, mutually exclusive elements.
Example: (config)# clock source {1|2} {none|ds1 1|ds1 2|ds1 3|ds1 4}
[]
Square brackets indicate an optional element.
Example: (config)# event-history priority [error|fatal|info|notice|warning]
{}
Braces indicate a required choice.
Example: (config)# clock {1|2} source {none|t1 port}
Boldface
Boldface indicated commands and keywords that are entered literally as shown. In actual
configuration examples and output (not general command syntax), boldface indicates commands
that are manually input by the user (i.e. show command).
Italics
Italics indicates arguments for which you supply values.
Command Line Interface Help
During a CLI session, help is available.
Type a ? at a command line, to display help on the command:
Example:
#?
?
clear
configure
copy
debug
end
exit
help
history
log
no
reload
show
upgrade
Display all commands
Clear command
Switch to Configure mode
Configures device database
Debug the system
Exit to User mode
Exit to User mode
Display all commands
Display past entered commands
Configure logging settings
Disable a feature
Reboot the system
Show various system information
Upgrade firmware from a local computer
#copy ?
defaults
path
running-config
Restores default configuration
Enter path to load configuration from
Export current configuration
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
1-5
Introduction
Shortcuts
Shortcuts
Keystroke
Up Arrow

Description
Use the up arrow key to re-display a previously entered command. Select the
up arrow repeatedly, to scroll through all the commands entered starting with
the most recent.
Will move curser one character to the left or right.
Left and Right Arrow
1-6
?
The question mark will display help for the current command.
[Tab]
Select the Tab key after entering a partial (but unique) portion of the CLI
command. This will result in the completion of a portion of the command
and will wait for further input.
Example:
(config)#sn [Tab]
(config)#snmp-server
auto complete
You need only enter enough letters to identify a command as unique. For
example, entering cont t1 1 at the Global configuration prompt provides you
access to the configuration parameters for the specified T1 interface.
Entering controller t1 1 would work as well, but is not necessary.
Backspace
Erases the character to the left.
History
The history shows up to a total of 100 commands. The history command will
show only the executed commands for the current mode/context.
[Ctrl+A]
Moves the curser to the beginning of the command line.
[Ctrl+E]
Moves the curser to the end of the command line.
[Ctrl+U]
Clears the current displayed command line.
[Ctrl+Z]
Exits from the current mode.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
2
User Mode
User mode is the first level of commands after logging in. User mode is represented by the >
prompt.
User Mode Commands
•
•
•
•
•
•
•
•
•
date
enable
end
exit
help
history
ping
show
traceroute
User Mode
date
Use the date command to display the current date.
Syntax:
> date
Example: adit 3500> date
Wed Jan 12 10:37:51 2007
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
enable
Use the enable command (at the User mode prompt) to enter the Privileged mode. Note: Once a correct
password has been entered, the prompt changes from ">" to "#".
Syntax:
> enable
Example: adit 3500> enable
password: ********
adit 3500#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
end
Use the end command to exit the current Configuration mode. Must be used to mark the end of any
configuration file. Note: This command can be entered in any Configuration mode with the same result.
Syntax:
> end
Example: Adit 3500> end
Adit 3500 Username:admin
Adit 3500 Password:********
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
2-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
exit
Use the exit command to close your current connection if you are in User mode or Privileged mode. If
the command is entered in a subconfiguration mode (Interface or Routing), this command takes you to
the previous level (example: back to Privileged mode from Interface configuration mode).
Syntax:
> exit
Example: Adit 3500> exit
Adit 3500 Username:admin
Adit 3500 Password:********
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
help
Use the help command to display help information. This can also be accomplished with a ?. This
command can be entered in any Configuration mode.
Syntax:
> help
or
> ?
Example: Adit 3500> help
?
Display all commands
date
Display time/date
enable
Enter Privileged mode
end
Logout from the device
exit
Exit from the current level
help
Display all commands
history
Display past entered commands
ping
Ping a remote host
show
Show various system information
traceroute
Traceroute to a remote host
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-3
User Mode
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any Configuration mode.
Syntax:
> history
Example: Adit 3500> history
date
ping 192.168.1.1 -n 4
show version
show users
show voice-port fxs
ping 192.168.1.1
show version
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
2-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
ping
Use the ping command to send a sequence of ICMP echo request packets to the specified host. If the
host variable is omitted, and you are in User mode, the router prompts you for additional information.
Note: The ping command verifies a connection, and is a very important troubleshooting tool.
Syntax:
> ping {address [-i time] [-l size] [-n count]
[-w timeout]|stop}
Field
Definition
address
IP address of the host to ping.
-i time
Specifies the intervals between pings.
Range is 0 - 600000 milliseconds.
-l size
Specifies the size of the ping requests packets to be sent. Range 64 1518.
-n count
Specifies the number of ping requests to be sent.
Range 1-1000. Default is 4.
-w timeout
Specifies the time to wait for a response before sending the next ping
request packet. Timeout is given in seconds. Range 1-600000. Default
is 2 seconds.
stop
Stop the ping process.
Example: Adit 3500> ping 192.168.1.1
packet #1 has arrived
packet #2 has arrived
packet #3 has arrived
packet #4 has arrived
4 packets transmitted, 4 packets received
round-trip min/avg/max = 1/3/9 ms
Example: Adit 3500> ping 192.168.1.1 -n 2 -l 500
packet #1 has arrived
packet #2 has arrived
2 packets transmitted, 2 packets received
round-trip min/avg/max = 2/2/2 ms
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-5
User Mode
show
2-6
show alarms
show ip ospf database
show arp
show ip ospf interface
show caclkcd
show ip ospf neighbor
show config dynamic-dns
show licenses
show controller lcc
show log
show controller t1
show mac-address-table
show dhcp-leases
show nat-fw
show digit-map
show port-trigger
show interface description
show route
show interface ethernet
show service
show interface multilink
show users
show interface serial
show version
show interface stats
show voice-port fxs
show ip ospf
show voice-port trunk
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
show alarms
Use the show alarms command to display the active alarms.
Syntax:
> show alarms [t1 port|lcc number]
{alert|all|critical|info|major|minor}
Field
Definition
t1 port
Display alarms for a specific port.
Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
lcc number
Display alarms for a specific Link Cross-Connect (LCC).
MSR: Range = 1-8.
alert
Filter alert alarms (threshold crossing).
all
Display all alarms.
critical
Filter critical alarms.
info
Filter information alarms.
major
Filter major alarms.
minor
Filter minor alarms.
Example: Adit 3500> show alarms all
Alarm
Severity
Time
Alarm LOS T1 4
Major
Jan
1 00:00:08 2007
Alarm LOS T1 3
Major
Jan
1 00:00:08 2007
Alarm PRI T1 2 - Line NOT Ready Major
Jan 1 00:00:08 2007
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-7
User Mode
show arp
Use the show arp command to display the ARP (Address Resolution Protocol) table.
Syntax:
> show arp {all|address|ethernet port}
Field
Definition
all
Display entire ARP table.
address
Display ARP items of the entered IP address.
ethernet port
Display Ethernet ARP items only.
port - Define an Ethernet port number. Range 1 - 2.
Example: adit 3500> show arp ethernet 1
1
192.168.1.1
ether
Dynam
00:50:da:59:f0:25
eth_lan
Example: adit 3500> show arp 192.168.1.1
ip=192.168.1.1
flags=Dynam mac=00:50:da:59:f0:25 iface=eth_lan
Example: adit 3500> show arp all
#
IP-address
HW-type
Flags
HW-address
Iface
1
192.168.1.1
ether
Dynam
00:50:da:59:f0:25
eth-1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
2-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
show caclkcd
Use the show caclkcd command to display the linux kernel crash dump
Syntax:
> show caclkcd
Example: Adit 3500> show caclkcd
---------------- Begin cacLKCD ----------Jan 1 2003 00:00:44 <3> openrg: unhandled page fault at pc=0x400528c0, lr=0x400
digit-map
Show digit-map settings
52890 (bad address=0x30303038, code 245)Show various interfaces
pc : [<400528c0>]
lr : [<40052890>]
No
Show l
r7 : 4006bb9c r6 : 30303038 r5 : 4006bb9c r4 : 4006bc1c
port-trigger
r3 : 30303030 r2 : 4006bc1c r1 : 4006bba5 r0 : 00000000
route
Show routing table
Flags: nzCv IRQs on FIQs on Mode USER_32 Segment user
Map the configurations to
CLI commands
User-mode stack:(0xbffffbac to 0xc0000000)
service
Display services
fba0:
00000001 0036d238 003704d0 0036d238 003704d0their privilages
versio
fbc0: 003704d4 0002e1e0 00000001 003704d0 0002e1a8 00000004 00000005 000281d4
voice-port
Show voice-port
fbe0: 4006d24d 4006d24c 4006d24c ffffffff 00000000 00rt
Show
fce0: 00024324 00469c08 00000001 00025144 00469c08 00469c08 0009575c 40050458ip address
Alarm LOS T1#2
fd00: 002c85a0 000001e3 40e88bc0 00000000 00000000 00000000 0009574c 0036c448
exit
fd60: 0036e270 00000000 00000000 00000004 00000094 bffffdbc 00000004 40033490
fd80: 00000000 00000000 00000000 00000094 0011121c 0000008c bffffdbc 00263674
fda0: 00000bfd 0000008c 0011138c ffffffff ffffffff 00000007 00111c44 feedbabe
fdc0: 00001063 00033bb6 0000004e 00000000 00000023 002c81e8 4006b010 400335dc
fde0: 00000000 00000000 00000000 002c8188 401a430c 002c8188 00000023 002c81e8
fe00: 001df753 00000000 401a4494 4003f960 001df753 001df730 002c8188 001df753
fe20: 001df730 4006b010 401a5ae4 00000023 001df730 00000000 00000000 00000000
fe40: 00000000 00000000 0000009c 00000000 065ca5ac 00000002 0000009c 00000000
fe60: 057aacc3 00000000 00000000 40047924 00000020 401bb254 40032cf0 4002ead4
fe80: 00000020 400054d0 0000009c 00000000 05a4faa0 00000002 400051a8 0000c222
fea0: 00000000 40000ca4 00000000 00000000 00000000 400051a8 0000938c 00000000
fec0: 00000039 00282fac 0000bc4c 4000c848 00000000 40000ca4 bfffff34 bfffff3c
fee0: 00000001 00000704 bfffff3c 00000001 bfffff30 00000000 00000000 4006b010
ff00: 00000000 40051048 bfffff34 401bb458 0001f828 401967e4 00000000 00000000
ff20: 0001145c 00000000 40196814 00000000 00011474 bfffffd2 00000000 bfffffde
ff40: bfffffe5 00000000 00000010 00000097 00000006 00001000 00000011 00000064
ff60: 00000003 00008034 00000004 00000020 00000005 00000006 00000007 40000000
ff80: 00000008 00000000 00000009 0001145c 0000000b 00000000 0000000c 00000000
ffa0: 0000000d 00000000 0000000e 00000000 0000000f bfffffce 00000000 00000000
ffc0: 00000000 00000000 00000000 00007635 62002f62 696e2f6f 70656e72 6700484f
ffe0: 4d453d2f 00544552 4d3d6c69 6e757800 2f62696e 2f6f7065 6e726700 00000000
---------------- End cacLKCD
-----------
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-9
User Mode
show config dynamic-dns
Use the show config dynamic-dns command to display the dynamic DNS configuration.
Syntax:
> show config dynamic-dns
Example: Adit 3500> show config dynamic-dns
dynamic-dns username admin hostname Host1
dynamic-dns interface eth-2
no dynamic-dns offline enable
no dynamic-dns wildcard enable
no dynamic-dns backup-mx enable
no dynamic-dns mail-exchanger
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show controller lcc
Use the show controller lcc command to display the settings for a Link Cross Connect on the MSR
card.
Syntax:
> show controller lcc number
Field
Definition
number
Link Cross Connect number, 1-8.
Example: Adit MSR> show controller lcc 1
Settings for interface LCC 1
--------------------------Name
: LinkCC 1
Device Name
: LinkCC 1
Status
: Operational
Network
: WAN
Connection Type : Link Cross Connect
Connection
: Data
Alarm Reporting : Enabled
Supported Platforms: MSR
2-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
show controller t1
Use the show controller t1 command to display the performance statistics of the DS1.
Syntax:
> show controller t1 port
Field
Definition
port
DS1 (T1) interface.
Adit 3104 range = 1
Adit 3500 range 1-4
Example: Adit 3500> show controller t1 1
Settings for interface T1 1
--------------------------Interface name
: T1 1
Transmit status : Up
Receive status
: Up
Framing
: ESF
Clock source
: Clock Reference 1
Line Code
: B8ZS
Loop Detection
: OFF
FDL Type
: NONE
Line Length
: DSX-1 equalization for 0-133ft
Status
: Connected
Performance Threshold Settings
unavailable seconds (uas):
severely errored seconds (ses):
errored seconds (es):
severely errored frame seconds (sefs):
line errored seconds (les):
controlled slip seconds (css):
bursty errored seconds (bes):
degraded minutes (dm):
line code violations (lcv):
path code violations (pcv):
15 min
-----0
0
0
0
0
0
0
0
0
0
1 day
----0
0
0
0
0
0
0
0
0
0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
Not supported on the MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-11
User Mode
show dhcp-leases
Use the show dhcp-leases command to display the DHCP lease table.
Syntax:
> show dhcp-leases
Example: Adit 3500> show dhcp-leases
Ethernet 1
Hostname : new-host IP:192.168.1.10 MAC:00:00:ff:ff:00:00
Type:static Expires-In:0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show digit-map
Use the show digit-map command to display the Digit Map settings.
Syntax:
> show digit-map
Example: Adit 3500> show digit-map
Index
Pattern
--------------------------------------------------------------1
[2-9]11
2
[0-1][2-9]11
3
0[#T]
4
00
5
*xx
6
011x.[#T]
7
[0-1]xxxxxxx[#T]
8
[0-1][2-9]xxxxxxxxx
9
[2-9]xxxxxxxxx
10
[2-9]xxxxxx[#T]
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
2-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
show interface description
Use the show interface description command to display interface information.
Syntax:
> show interface description
Example: Adit 3500> show interface description
Device
State
IP/Mask
Dependencies
T1 1
running
None
T1 2
running
None
T1 3
up
None
T1 4
up
None
Serial 1
up
0.0.0.0/255.255.255.255
T1 1
Ethernet 2
disabled
0.0.0.0/0.0.0.0
None
Ethernet 1
running
192.168.1.1/255.255.255.0
None
IPsec 0
disabled
0.0.0.0/0.0.0.0
Serial 1
IPsec 1
running
192.168.1.1/255.255.255.0
Ethernet 1
Example: Adit MSR> show interface description
Device
State
IP/Mask
Dependencies
LinkCC 1
running
None
LinkCC 2
running
None
LinkCC 3
down
None
LinkCC 4
down
None
LinkCC 5
down
None
LinkCC 6
down
None
LinkCC 7
down
None
LinkCC 8
down
None
Ethernet 2
up
DHCP Unassigned
None
Ethernet 1
running
192.168.1.1/255.255.255.0
None
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-13
User Mode
show interface ethernet
Use the show interface ethernet command to display the Ethernet interface information.
Syntax:
> show interface ethernet port
Field
Definition
port
Ethernet port number. Range = 1-2.
Example: Adit 3500> show interface ethernet 1
Device=Ethernet 1
State=running
IP/Mask=192.168.1.1/255.255.255.0
Dependency=None
Status: Connected; Link: 10T-HD
Tx (Packets/Bytes/Dropped/Errors)=(1620/1643674/0/0)
Rx (Packets/Bytes/Dropped/Errors)=(1636/143050/0/0)
Broadcasts (Tx/Rx)=(0/0) Multicasts=0 Collisions=0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show interface multilink
Use the show interface multilink command to display the multilink configuration information.
Syntax:
> show interface multilink port
Field
Definition
port
Multilink port number.
Adit 3104, Adit 3200, Adit 3500: Value must be 1.
MSR: Range is 1-8
Example: Adit 3500> show interface multilink 1
Device=mlink-1
State=down
Dependency=t1-1,t1-3
Status: Disconnected
IP/Mask=Unnumbered
Example: Adit MSR> show interface multilink 1
Device=mlink-1
State=down
Dependency=LCC1,LCC2
Status: Disconnected
IP/Mask=Unnumbered
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
2-14
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
show interface serial
Use the show interface serial command to display the configuration of the serial interface.
Syntax:
> show interface serial port
Field
Definition
port
Serial interface.
Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
MSR: Range = 1-8.
Example: Adit 3500> show interface serial 3
Device=Serial 1
State=up
IP/Mask=0.0.0.0/255.255.255.255
Dependency=T1 1
Status: Reconnecting...
Tx (Packets/Bytes/Dropped/Errors)=(3332/39984/0/0)
Rx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)
Example: Adit MSR> show interface serial 3
Device=Serial 1
State=up
IP/Mask=0.0.0.0/255.255.255.255
Dependency=LCC1
Status: Reconnecting...
Tx (Packets/Bytes/Dropped/Errors)=(3332/39984/0/0)
Rx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-15
User Mode
show interface stats
Use the show interface stats command to display the interface statistics.
Syntax:
> show interface stats
Example: Adit 3500> show interface stats
Device=T1 1
State=up
Dependency=None
Status: Connecting (Alarm Condition)
Device=T1 2
State=up
Dependency=None
Status: Connecting (Alarm Condition)
Device=T1 3
State=running
Dependency=None
Status: Connected
Device=T1 4
State=running
Dependency=None
Status: Connected
Device=Serial 1
State=down
Dependency=T1 1
Status: Disconnected
Device=Ethernet 2
State=disabled
IP/Mask=192.168.2.10/255.255.255.0
Dependency=None
Device=Ethernet 1
State=running
IP/Mask=192.168.1.35/255.255.255.0
Dependency=None
IP/Mask=0.0.0.0/255.255.255.255
Status: Connected; Link: 10T-HD
Tx (Packets/Bytes/Dropped/Errors)=(2362/2498024/0/0)
Rx (Packets/Bytes/Dropped/Errors)=(2211/210493/0/0)
Broadcasts (Tx/Rx)=(0/0) Multicasts=0 Collisions=0
Device=IPsec 0
State=disabled
IP/Mask=0.0.0.0/0.0.0.0
Dependency=Serial 1
Device=IPsec 1
State=running
IP/Mask=192.168.1.35/255.255.255.0
Dependency=Ethernet 1Status: Connected
Tx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)
Rx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)
Example: Adit MSR> show interface stats
Device=LinkCC 1
State=running
Dependency=None
Status: Operational
Device=LinkCC 2
State=running
Dependency=None
Status: Operational
Device=LinkCC 3
State=down
Dependency=None
Status: Unassigned
Device=LinkCC 4
State=down
Dependency=None
Status: Unassigned
Device=LinkCC 5
State=down
Dependency=None
Status: Unassigned
Device=LinkCC 6
State=down
Dependency=None
Status: Unassigned
Device=LinkCC 7
State=down
Dependency=None
2-16
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
Status: Unassigned
Device=LinkCC 8
State=down
Dependency=None
Status: Unassigned
Device=Ethernet 2
State=up
Dependency=None
IP/Mask=DHCP Unassigned
Status: DHCP IP Address Released; Link: Down
Tx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)
Rx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)
Broadcasts (Tx/Rx)=(0/0) Multicasts=0 Collisions=0
Device=Ethernet 1
State=running
IP/Mask=10.0.0.3/255.255.255.0
Dependency=None
Status: Connected; Link: 10T-HD
Tx (Packets/Bytes/Dropped/Errors)=(1509/1577037/0/0)
Rx (Packets/Bytes/Dropped/Errors)=(1540/119409/0/0)
Broadcasts (Tx/Rx)=(0/0) Multicasts=0 Collisions=0
Supported Platforms:Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-17
User Mode
show ip ospf
Use the show ip ospf command to display the general OSPF routing process information.
Syntax:
> show ip ospf
Example: adit 3500> show ip ospf
Routing Process "ospf 0" with ID 192.168.1.1
Process uptime is 28 minutes
Process bound to VRF default
Conforms to RFC2328, and RFC1583Compatibility flag is disabled
Supports only single TOS(TOS0) routes
Supports opaque LSA
Supports Graceful Restart
SPF schedule delay 5 secs, Hold time between two SPFs 10 secs
Refreshtimer 10 secs
Number of incoming current DD exchange neighbors 0/5
Number of outgoing current DD exchange neighbors 0/5
Number of external LSA 0. Checksum 0x000000
Number of opaque AS LSA 0. Checksum 0x000000
Number of router LSA 0
Router LSA database is unlimited.
Number of network LSA 0
Network LSA database is unlimited.
Number of non-default summary LSA 0
Summary LSA database is unlimited.
Number of asbr summary LSA 0
ASBR Summary LSA database is unlimited.
Number of non-default external LSA 0
External LSA database is unlimited.
Number of LSA originated 0
Number of LSA received 0
Number of areas attached to this router: 0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
2-18
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
show ip ospf database
Use the show ip ospf database command to display information related to the OSPF database for
a specific router. The various forms of this command deliver information on defined OSPF link
state advertisements.
Syntax:
> show ip ospf database {setting}
Syntax:
> show ip ospf database {adv-router address|self-originate}
Syntax:
> show ip ospf database network link-state-id
Syntax:
> show ip ospf database router {link-state-id|adv-router
address|self-originate}
Syntax:
> show ip ospf database summary [link-state-id] [adv-router
address|self-originate]
Field
Definition
adv-router address
Displays all the LSAs of the specified router. If no IP address is
entered, the local router information will be displayed (same as selforiginate).
link-state-id
Portion of the Internet environment that is being described by the
advertisement. The value entered depends on the advertisement's LS
type. It must be entered in the form of an IP address. When the link
state advertisement is describing a network, the link-state-id can take
one of two forms:
1. The network's IP address (as in type 3 summary link advertisements
and in autonomous system external link advertisements).
2. A derived address obtained from the link state ID. (Note that
masking a network links advertisement's link state ID with the
network's subnet mask yields the network's IP address.)
When the link state advertisement is describing a router, the link state
ID is always the described router's OSPF router ID.
When an autonomous system external advertisement (LS Type = 5) is
describing a default route, its link state ID is set to Default Destination
(0.0.0.0).
network
Displays information only about the network LSAs.
router
Displays information only about the Router LSAs.
self-originate
Displays only self-originated LSAs (from the local router).
summary
Displays information on.ly about the summary LSAs.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-19
User Mode
Example: adit 3500> show ip ospf database
Router Link States (Area 0.0.0.1)
Link ID
192.168.3.1
192.168.3.255
ADV Router
192.168.3.1
192.168.3.255
Age Seq#
CkSum Link count
313 0x800000c1 0x4978 1
568 0x8000003a 0xa6c0 1
Net Link States (Area 0.0.0.1)
Link ID
192.168.3.251
ADV Router
192.168.3.255
Age Seq#
CkSum
388 0x80000003 0xbcec
Example: adit 3500> show ip ospf database self-originate
Router Link States (Area 0.0.0.1)
Link ID ADV Router Age Seq# CkSum Link count
192.168.3.255 192.168.3.255 420 0x8000003a 0xa6c0 1
Net Link States (Area 0.0.0.1)
Link ID ADV Router Age Seq# CkSum
192.168.3.251 192.168.3.255 240 0x80000003 0xbcec
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
2-20
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
show ip ospf interface
Use the show ip ospf interface command to display OSPF related interface information.
Syntax:
> show ip ospf interface {ethernet port|serial port|multilink
port}
Field
Definition
ethernet port
Display information on the Ethernet interface.
port = 1 or 2
serial port
Display information on the serial interface.
Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
MSR: Range = 1-8.
multilink port
Display information on the Multilink interface.
Adit 3104, Adit 3500, MSR: Value must be 1
Example: adit 3500> show ip ospf interface ethernet 1
Ethernet 1 is up, line protocol is up
Internet Address 192.168.254.202, Mask 255.255.255.0, Area 0.0.0.0
AS 201, Router ID 192.168.99.1, Network Type BROADCAST, Cost: 10
Transmit Delay is 1 sec, State OTHER, Priority 1
Designated Router id 192.168.254.10, Interface address 192.168.254.10
Backup Designated router id 192.168.254.28, Interface addr 192.168.254.28
Timer intervals configured, Hello 10, Dead 60, Wait 40, Retransmit 5
Hello due in 0:00:05
Neighbor Count is 8, Adjacent neighbor count is 2
Adjacent with neighbor 192.168.254.28 (Backup Designated Router)
Adjacent with neighbor 192.168.254.10 (Designated Router)
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-21
User Mode
show ip ospf neighbor
Use the show ip ospf neighbor command to display OSPF neighbor information.
Syntax:
> show ip ospf neighbor [interface address|neighbor-id|detail]
Field
Definition
interface address
Optional parameter. Enter interface IP address to define display.
neighbor-id
Optional parameter. Enter neighbor IP address to define display.
detail
Optional parameter. Enable display of detailed information.
Example: adit 3500> show ip ospf neighbor
ID
Pri
10.199.199.137 1
172.16.48.1
1
172.16.48.200
1
10.199.199.137 5
State
Dead Time
FULL/DR
0:00:31
FULL/DROTHER 0:00:33
FULL/DROTHER 0:00:33
FULL/DR
0:00:33
Address
192.168.80.37
172.16.48.1
172.16.48.200
172.16.48.189
Interface
Ethernet1
Fddi0
Fddi0
Fddi0
Example: adit 3500> show ip ospf neighbor 10.199.199.137
Neighbor 10.199.199.137, interface address 192.168.80.37
In the area 0.0.0.0 via interface Ethernet0
Neighbor priority is 1, State is FULL
Options 2
Dead timer due in 0:00:32
Link State retransmission due in 0:00:04
Neighbor 10.199.199.137, interface address 172.16.48.189
In the area 0.0.0.0 via interface Fddi0
Neighbor priority is 5, State is FULL
Options 2
Dead timer due in 0:00:32
Link State retransmission due in 0:00:03
Example: adit 3500> show ip ospf neighbor detail
Neighbor 192.168.5.2, interface address 10.225.200.28
In the area 0 via interface GigabitEthernet1/0/0
Neighbor priority is 1, State is FULL, 6 state changes
DR is 10.225.200.28 BDR is 10.225.200.30
Options is 0x42
LLS Options is 0x1 (LR), last OOB-Resync 00:03:08 ago
Dead timer due in 00:00:36
Neighbor is up for 00:09:46
Index 1/1, retransmission queue length 0, number of retransmission 1
First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)
Last retransmission scan length is 1, maximum is 1
Last retransmission scan time is 0 msec, maximum is 0 msec
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
2-22
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
show licenses
Use the show licenses command to display all enabled feature keys.
Syntax:
> show licenses
Example: Adit 3500> show licenses
VPN
SIP
MGCP
G729A
license
license
license
license
=
=
=
=
No
Yes
No
Yes
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show log
Use the show log command to display the current events on the system.
Syntax:
> show log {firewall|pri|sip|system|t1 port|lcc number}
{severity}
Field
Definition
firewall
Filter firewall alarms
pri
Display PRI logs. Note: This is not supported on the Adit 3104.
sip
Display SIP logs.
system
Filter general system alarms
t1 port
Display event log for a specific T1 port.
Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
lcc number
Display event log for a specific Link Cross-Connect (LCC).
MSR: Range = 1-8.
severity
alert - Filter alert alarms (threshold crossing)
all - Display all alarms
critical - Filter critical alarms (service affecting)
info - Filter informational alarms
major - Filter major alarms (service affecting)
minor - Filter minor alarms (non-service affecting)
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-23
User Mode
Example: Adit 3500> show log t1 1 minor
System
System
System
System
System
System
System
System
Log
Log
Log
Log
Log
Log
Log
Log
Message
Message
Message
Message
Message
Message
Message
Message
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
1
1
1
1
1
1
1
1
00:00:08
00:00:04
01:19:13
00:57:12
00:56:52
00:56:34
00:56:09
00:00:04
2003
2003
2003
2003
2003
2003
2003
2003
kern.err
kern.err
kern.err
kern.err
kern.err
kern.err
kern.err
kern.err
T1
T1
T1
T1
T1
T1
T1
T1
ALARM:
ALARM:
ALARM:
ALARM:
ALARM:
ALARM:
ALARM:
ALARM:
Alarm
Alarm
Alarm
Alarm
Alarm
Alarm
Alarm
Alarm
LOS
LOS
LOS
LOS
LOS
LOS
LOS
LOS
T1#1
T1#1
T1#1
T1#1
T1#1
T1#1
T1#1
T1#1
Major
Major
Major
Major
Major
Major
Major
Major
received
received
received
received
received
received
received
received
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show mac-address-table
Use the show mac-address-table command to display the current MAC addresses (LAN\WAN).
Syntax:
> show mac-address-table
Example: Adit 3500> show mac-address-table
Ethernet 1 mac= 00:00:00:ff:ff:ff
Ethernet 2 mac= 00:00:00:ff:ff:fd
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
2-24
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
show nat-fw
Use the show nat-fw command to display the current NAT and firewall connection table.
Syntax:
> show nat-fw
Example: Adit 3500> show nat-fw
Number Content
1
TCP 11.0.0.4
36104<--> 172.15.16.1
36104[31.0.0.6 5516 ]
TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1320 pkts 7 ppp100 Outgoing BY FTP
2
TCP 11.0.0.4
36103<--> 172.15.16.1
36103[31.0.0.6 21
]
TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1182 pkts 20 FTP child: Yes ppp100 Outgoing
3
TCP 11.0.0.4
36102<--> 172.15.16.1
36102[31.0.0.6 5515 ]
TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1320 pkts 7 ppp100 Outgoing BY FTP
4
TCP 11.0.0.4
36101<--> 172.15.16.1
36101[31.0.0.6 21
]
TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1182 pkts 20 FTP child: Yes ppp100 Outgoing
5
UDP 172.15.16.2
28015<--> 172.15.16.2
28015[*.*.*.*
ttl 79 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP
*]
6
UDP 172.15.16.2
28014<--> 172.15.16.2
28014[*.*.*.*
ttl 79 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP
*]
7
UDP 172.15.16.2
28013<--> 172.15.16.2
28013[*.*.*.*
ttl 77 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP
*]
8
UDP 172.15.16.2
28012<--> 172.15.16.2
28012[*.*.*.*
ttl 77 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP
*]
9
UDP 172.15.16.2
28011<--> 172.15.16.2
28011[*.*.*.*
ttl 75 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP
*]
10
UDP 172.15.16.2
28010<--> 172.15.16.2
28010[*.*.*.*
ttl 75 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP
*]
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-25
User Mode
show port-trigger
Use the show port-trigger command to display all port triggering information.
Syntax:
> show port-trigger
Example: Adit 3500> show port-trigger
Service ID:134217730 Enable Service Name:L2TP
Trigger protocol: UDP port: src_start=0
src_end=0
dst_start=1701
Service ID:16777223 Enable Service Name:TFTP
Trigger protocol: UDP port: src_start=1024 src_end=65535
dst_end=1701
dst_start=69 dst_end=69
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show route
Use the show route command to display the routing table.
Syntax:
> show route
Example: Adit 3500> show route
Destination
192.168.1.0/24
192.168.1.0/24
Gateway
*
*
Flags
U
U
Metric
50
51
Interface
Ethernet 1
IPsec 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
2-26
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
show service
Use the show service command to displays all services.
Syntax:
> show service
Example: Adit 3500> show service
Group: Basic Web Utilities
Service ID:16777216 Service Name:All Traffic
Trigger protocol: NO PROTOCOL port: src_start=0
src_end=0
Service ID:16777217 Service Name:DNS
Trigger protocol: TCP port: src_start=53
src_end=53
Service ID:16777217 Service Name:DNS
Trigger protocol: TCP port: src_start=1024
Service ID:16777217 Service Name:DNS
Trigger protocol: UDP port: src_start=1024
dst_start=53
dst_end=53
dst_end=53
dst_start=53
dst_start=21
dst_end=0
dst_end=53
dst_start=53
src_end=65535
Service ID:16777218 Service Name:FTP
Trigger protocol: TCP port: src_start=0
src_end=0
Service ID:16777219
dst_start=53
src_end=65535
Service ID:16777217 Service Name:DNS
Trigger protocol: UDP port: src_start=53
src_end=53
dst_start=0
dst_end=53
dst_end=21
Service Name:HTTP
.
.
.
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-27
User Mode
show users
Use the show users command to displays all users on this system.
Syntax:
> show users
Example: Adit 3500> show users
Provisioned User List
User-1 : admin
Access: ADMIN <User-2 : pauljones Access: ADMIN
Active CLI Users
User-1 : admin
Access:ADMIN
Authen:Config
User-2 : admin
Access:ADMIN
Authen:Config
from IP:192.168.1.1
from Console
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show version
Use the show version command to displays the version for the hardware, software and firmware.
The Admin level user will be provided with more information than Manager and Monitor levels.
Software features are listed along with enabled status.
Syntax:
> show version
Example: Adit 3500> show version
Application Version: 1.4.0
Compilation Time: Thu Jul 20 2006 13:48:42
FPGA Version: 1.0.0
Board Version: 1 003-1215-0100
IXP400 Software Release: 1_4 SQA4_1
MSP:
82530 - 60 channels
Image File Name: TGW_v5_03_cdma.axf
API Version
: 2.1.0
Source IP Addr : 192.168.1.1
Voice Slot 1 : FXS Card Present: Rev 5.00 VIP
Vendor: Turin Networks
CLEI Code: IPMHX00LRA
Product Features:
SIP enabled.
G729A enabled.
2-28
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
Example: Adit MSR> show version
Application Version: 2.0.0.5
Compilation Time: Thu Jan 31 2008 13:48:42
FPGA Version: 0.04
Boot Version: 1.14
Board Version: 0 003-1756-0001
Flash Size: 32M bytes
Memory Size: 64M bytes
IXP400 Software Release: 1_4 SQA4_1
MSP:
82610 - 100 channels
Image File Name: TGW_v5_05.axf
API Version
: 2.1.0
Source IP Addr : 10.10.4.202
MSR Card Slot: 5
CLEI Code: SITRAANBAA
Product Features:
VPN enabled.
SIP enabled.
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-29
User Mode
show voice-port fxs
Use the show voice-port fxs command to display the FXS interface information.
Syntax:
> show voice-port fxs
Example: Adit 3500> show voice-port fxs
Registration Address: 172.32.1.15
SIP Proxy: Yes
Proxy Address: 172.32.1.18
* Line UID
PhoneStatus RegisStatus RX/TX/Lost(Pkts) Jitter Overflow
---------------------------------------------------------------------------Y 1
3035550001
Idle
Registered
Y 2
3035550002
Idle
Registered
Y 3
3035550003
Idle
Registered
Y 4
3035550004
Idle
Registered
Example: Adit MSR> show voice-port fxs
Registration Address: 172.32.1.15
SIP Proxy: Yes
Proxy Address: 172.32.1.18
* Line UID
PhoneStatus RegisStatus RX/TX/Lost(Pkts) Jitter Overflow CrossConnect
-----------------------------------------------------------------------------------------Y 1
3035550001
Idle
Registered
Connected
Y 2
3035550002
Idle
Registered
Connected
Y 3
3035550003
Idle
Registered
Connected
Y 4
3035550004
Idle
Registered
Connected
Y 5
3035550005
Idle
Registered
Connected
Y 6
3035550006
Idle
Registered
Connected
Y 7
3035550007
Idle
Registered
Connected
Y 8
3035550008
Idle
Registered
Connected
.
.
.
Supported Platforms: Adit 3104, Adit 3500, MSR
2-30
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
show voice-port trunk
Use the show voice-port trunk command to display the voice trunk statistics.
Syntax:
> show voice-port trunk port
Field
Definition
port
Adit 3500: DS1 (T1) interface. Value must be 1.
MSR: Link Cross Connect (LCC). Range = 1-8.
Example: Adit 3500> show voice-port trunk 1
trunk-1 t1-1 does not exist
******************************* CAS 2 *************************************
Channel no
Internal Call Id
Q931 Connection Id
Tdm TimeSlot
Call State
------------------------------------------------------------------------------1
-1
-1
-1
INACTIVE
2
-1
-1
-1
INACTIVE
3
-1
-1
-1
INACTIVE
4
-1
-1
-1
INACTIVE
5
-1
-1
-1
INACTIVE
6
-1
-1
-1
INACTIVE
7
-1
-1
-1
INACTIVE
8
-1
-1
-1
INACTIVE
9
-1
-1
-1
INACTIVE
10
-1
-1
-1
INACTIVE
11
-1
-1
-1
INACTIVE
12
-1
-1
-1
INACTIVE
13
-1
-1
-1
INACTIVE
14
-1
-1
-1
INACTIVE
15
-1
-1
-1
INACTIVE
16
-1
-1
-1
INACTIVE
17
-1
-1
-1
INACTIVE
18
-1
-1
-1
INACTIVE
19
-1
-1
-1
INACTIVE
20
-1
-1
-1
INACTIVE
21
-1
-1
-1
INACTIVE
22
-1
-1
-1
INACTIVE
23
-1
-1
-1
INACTIVE
24
-1
-1
-1
INACTIVE
trunk-1 t1-3 does not exist
trunk-1 t1-4 does not exist
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-31
User Mode
Example: Adit MSR> show voice-port trunk 1
******************************* PRI 1 ***************************************
Channel no
Internal Call Id
Q931 Connection Id
Tdm TimeSlot
Call State
------------------------------------------------------------------------------1
-1
-1
-1
INACTIVE
2
-1
-1
-1
INACTIVE
3
-1
-1
-1
INACTIVE
4
-1
-1
-1
INACTIVE
5
-1
-1
-1
INACTIVE
6
-1
-1
-1
INACTIVE
7
-1
-1
-1
INACTIVE
8
-1
-1
-1
INACTIVE
9
-1
-1
-1
INACTIVE
10
-1
-1
-1
INACTIVE
11
-1
-1
-1
INACTIVE
12
-1
-1
-1
INACTIVE
13
-1
-1
-1
INACTIVE
14
-1
-1
-1
INACTIVE
15
-1
-1
-1
INACTIVE
16
-1
-1
-1
INACTIVE
17
-1
-1
-1
INACTIVE
18
-1
-1
-1
INACTIVE
19
-1
-1
-1
INACTIVE
20
-1
-1
-1
INACTIVE
21
-1
-1
-1
INACTIVE
22
-1
-1
-1
INACTIVE
23
-1
-1
-1
INACTIVE
trunk 1 LCC#2 does not exist
trunk 1 LCC#3 does not exist
trunk 1 LCC#4 does not exist
trunk 1 LCC#5 does not exist
trunk 1 LCC#6 does not exist
trunk 1 LCC#7 does not exist
trunk 1 LCC#8 does not exist
Supported Platforms: Adit 3500, MSR
2-32
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
User Mode
traceroute
Use the traceroute command to trace a route to a remote host.
Syntax:
> traceroute
Syntax:
> traceroute {address|hostname|stop}
Field
Definition
address
IP address of the remote host.
hostname
Host name of the remote host.
stop
Stop the traceroute process.
Example: Adit 3500> traceroute to 192.168.1.200
(192.168.1.200), 10 hops max
1 192.168.1.200 (192.168.1.200) 10.500 ms 1.013 ms 0.926 ms
Traceroute: Destination Reached
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
2-33
User Mode
2-34
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
3
Privileged Mode
The Privileged Mode allows the operator access to the configuration modes.
This Mode is entered with the > enable command from the Basic mode.
The Privileged Mode is represented by the # prompt.
Privileged Mode Commands
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
clear
configure terminal
copy
date
debug
end
exit
help
history
log clear
no debug
ping
reload
show
traceroute
upgrade
Privileged Mode
clear
clear arp
Use the clear arp command to clear the ARP (Address Resolution Protocol) table.
Syntax:
# clear arp {all|ethernet port|address}
Field
Definition
all
Display entire ARP table.
ethernet port
Display Ethernet ARP items only.
port - Define an Ethernet port number. Range 1 - 2.
address
Enter IP address for specific ARP information on this address.
Example: adit 3500# clear arp ethernet 1
arp entries removed on eth-1 interface
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
clear caclkcd
Use the clear arp command to clear the linux kernel crash dump.
Syntax:
# clear caclkcd
Example: adit 3500# clear caclkcd
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
clear ip ospf process
Use the clear ip ospf process command to restart the OSPF process with the LSA databases and
counters reinitialized.
Syntax:
# clear ip ospf process
Example: adit 3500# clear ip ospf process
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
configure terminal
Use the configure terminal command to enter the configuration mode.
Syntax:
# configure terminal
Example: adit 3500# configure terminal
adit 3500 (config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
copy
copy defaults
Use the copy defaults command to restore default setting.
Syntax:
# copy defaults running-config
Example: adit 3500# copy defaults running-config
Going to reboot!
Restarting system.
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
copy path
Use the copy path command to load a configuration saved on your computer to the Adit system.
Note: A TFTP server must be running on your computer.
Syntax:
# copy path {source-path} running-config
Field
Definition
source-path
Enter the source path, in the form tftp://address/filename
address - Enter IP address of the TFTP server.
filename - Enter the name of the configuration file to load onto the
system.
Example: adit 3500# copy path tftp://192.168.1.100/a3500_config runningconfig
adit 3500#Configuration restore: Success
WARNING: A reload is needed for changes to take effect.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-3
Privileged Mode
Example: Adit MSR#copy path tftp://192.168.1.100/MSR_config runningconfig
Adit MSR#Configuration restore: Success.
WARNING: A reload is needed for changes to take effect.
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
copy running-config
Use the copy running-config command to save the current configuration on the Adit.
Note: The TFTP server must be running on the destination device.
Syntax:
# copy running-config path {destination-path}
Field
Definition
destination-path
Enter the destination path, in the form tftp://address/filename to the
location where the configuration file is to be saved.
address - Enter IP address of the TFTP server.
filename - Enter a name for this new configuration file.
Example: adit 3500# copy running-config path tftp://192.168.1.100/
a3500_config
adit 3500# Configuration save: Success
Example: Adit MSR#copy running-config path tftp://192.168.1.100/
testconfig
Adit MSR#Configuration save: Success
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
date
Use the date command to display the current date.
Syntax:
# date
Example: Adit 3500# date
Wed Jan 12 10:37:51 2007
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
debug
debug portmon all
Use the debug portmon all command allows the user to monitor all traffic of a specific type. All
traffic can be displayed, or a specific traffic type can be defined. Note: Immediately after this
command is issued, any traffic that falls into the filter parameter will be displayed. To turn the
monitoring off, you must issue a no debug portmon command. See no debug portmon command
on page 3-16.
Syntax:
# debug portmon all [all|arp address|bootp address|control
|data|dns address|icmp address|ip address|link|mgcp address|
rip address|sip address|stp|tcp {address|address:port|port}|
udp {address|address:port|port}]
Field
Definition
Filters all traffic of the following type.
all
Allows all traffic.
arp
Displays all Address Resolution Protocol traffic.
address = IP address of the interface.
bootp
Displays BootP related traffic.
address = IP address of the interface.
control
Displays control related traffic.
data
Displays data related traffic.
dns
Displays Domain Naming Service related traffic.
address = IP address of the interface.
icmp
Displays Internet Control Message Protocol related traffic.
address = IP address of the interface.
ip
Displays Internet Protocol related traffic Note: Requires an IP address.
address = IP address of the interface.
link
Displays link related traffic.
mgcp
Displays Media Gateway Control Protocol related traffic.
address = IP address of the interface.
rip
Displays Routing Information Protocol related traffic.
address = IP address of the interface.
sip
Displays Session Initiation Protocol related traffic.
address = IP address of the interface.
stp
Displays Spanning Tree Protocol related traffic.
tcp
Displays Transmission Control Protocol related traffic.
address = IP address of the interface.
address:port = IP address
port = Port of the interface
udp
Displays User Datagram Protocol related traffic.
address = IP address of the interface.
address:port = IP address:port of the interface.
port = Port of the interface
Example: adit 3500# debug portmon all rip 192.168.1.20
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-5
Privileged Mode
debug portmon {rx|tx|both}
Use the debug portmon {rx|tx|both} command allows the user to monitor specific direction of
traffic.
Note: Immediately after this command is issued, any traffic that falls into the filter parameter will
be displayed. To turn the monitoring off, you must issue a no debug portmon command. See no
debug portmon command on page 3-16.
Syntax:
# debug portmon {rx|tx|both}
Field
Definition
both
Display both receive and transmit information.
rx
Display the receive direction.
tx
Display the transmit direction.
Example: adit 3500# debug portmon both
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
debug portmon detail
Use the debug portmon detail command allows the user to configure the portmon to display brief
information or detailed. See no debug portmon command on page 3-16.
Syntax:
# debug portmon detail {off|on}
Field
Definition
off
Disables detail packet display
on
Enable detailed packet display
Example: adit 3500# debug portmon detail on
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
debug portmon ethernet
Use the debug portmon ethernet command allows the user to monitor specific Ethernet traffic.
Note: Immediately after this command is issued, any traffic that falls into the filter parameter will
be displayed. To turn the monitoring off, you must issue a no debug portmon command. See no
debug portmon command on page 3-16.
Syntax:
# debug portmon ethernet {1|2|both} [all|arp address|bootp
address|control|data|dns address|icmp address|ip address|link|
mgcp address|rip address|sip address|stp|tcp {address|
address:port|port}|udp {address|address:port|port}]
Field
Definition
ethernet
Display Ethernet traffic.
1 or 2 - Define Ethernet port
both - Both Ethernet ports
Filters all traffic of the following type.
all
Allows all traffic.
arp
Displays all Address Resolution Protocol traffic.
address = IP address of the interface.
bootp
Displays BootP related traffic.
address = IP address of the interface.
control
Displays control related traffic.
data
Displays data related traffic.
dns
Displays Domain Naming Service related traffic.
address = IP address of the interface.
icmp
Displays Internet Control Message Protocol related traffic.
address = IP address of the interface.
ip
Displays Internet Protocol related traffic Note: Requires an IP address.
address = IP address of the interface.
link
Displays link related traffic.
mgcp
Displays Media Gateway Control Protocol related traffic.
address = IP address of the interface.
rip
Displays Routing Information Protocol related traffic.
address = IP address of the interface.
sip
Displays Session Initiation Protocol related traffic.
address = IP address of the interface.
stp
Displays Spanning Tree Protocol related traffic.
tcp
Displays Transmission Control Protocol related traffic.
address = IP address of the interface.
address:port = IP address
port = Port of the interface
udp
Displays User Datagram Protocol related traffic.
address = IP address of the interface.
address:port = IP address:port of the interface.
port = Port of the interface
Example: adit 3500# debug portmon ethernet 1 all
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-7
Privileged Mode
debug portmon management
Use the debug portmon management command allows the user to configure management trace
suppression. See no debug portmon command on page 3-16.
Syntax:
# debug portmon management {hush|off}
Field
Definition
hush
hush - Enable suppression of management traffic trace
off
off - Disable suppression of management traffic trace
Example: adit 3500# debug portmon management hush
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
debug portmon multilink
Use the debug portmon multilink command allows the user to monitor the multilink traffic. All
traffic can be displayed, or a specific traffic type can be defined.
Note: Immediately after this command is issued, any traffic that falls into the filter parameter will
be displayed. To turn the monitoring off, you must issue a no debug portmon command. See no
debug portmon command on page 3-16
Syntax:
# debug portmon multilink port {all|arp address|bootp
address|control|data|dns address|icmp address|ip address
|link|mgcp address|rip address|sip address|stp|tcp {address|
address:port|port}|udp {address|address:port|port}}
Field
Definition
port
Enter multilink port. Range 1.
all
Allows all traffic.
arp
Displays all Address Resolution Protocol traffic.
address = IP address of the interface.
bootp
Displays BootP related traffic.
address = IP address of the interface.
control
Displays control related traffic.
data
Displays data related traffic.
dns
Displays Domain Naming Service related traffic.
address = IP address of the interface.
icmp
Displays Internet Control Message Protocol related traffic.
address = IP address of the interface.
ip
Displays Internet Protocol related traffic Note: Requires an IP address.
address = IP address of the interface.
link
Displays link related traffic.
mgcp
Displays Media Gateway Control Protocol related traffic.
address = IP address of the interface.
rip
Displays Routing Information Protocol related traffic.
address = IP address of the interface.
sip
Displays Session Initiation Protocol related traffic.
address = IP address of the interface.
stp
Displays Spanning Tree Protocol related traffic.
tcp
Displays Transmission Control Protocol related traffic.
address = IP address of the interface.
address:port = IP address
port = Port of the interface
udp
Displays User Datagram Protocol related traffic.
address = IP address of the interface.
address:port = IP address:port of the interface.
port = Port of the interface
Example: adit 3500# debug portmon multilink 1 mgcp 192.168.1.140
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-9
Privileged Mode
debug portmon raw
Use the debug portmon raw command allows the user to display raw data related traffic. See no
debug portmon command on page 3-16.
Syntax:
# debug portmon raw {off|on}
Field
Definition
off
Disable display of packet hex data
on
Enables display of packet hex data
Example: adit 3500# debug portmon raw off
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
debug portmon serial
Use the debug portmon serial command allows the user to monitor traffic on a serial interface.
Note: Immediately after this command is issued, any traffic that falls into the filter parameter will
be displayed. To turn the monitoring off, you must issue a no debug portmon command. See no
debug portmon command on page 3-16.
Syntax:
# debug portmon serial port {all|arp address|bootp
address|control|data|dns address|icmp address|ip address
|link|mgcp address|rip address|sip address|stp|tcp {address|
address:port|port}|udp {address|address:port|port}}
Field
Definition
port
Displays specific port traffic.
Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
MSR: Range = 1-8.
all
Allows all traffic.
arp
Displays all Address Resolution Protocol traffic.
address = IP address of the interface.
bootp
Displays BootP related traffic.
address = IP address of the interface.
control
Displays control related traffic.
data
Displays data related traffic.
dns
Displays Domain Naming Service related traffic.
address = IP address of the interface.
icmp
Displays Internet Control Message Protocol related traffic.
address = IP address of the interface.
ip
Displays Internet Protocol related traffic Note: Requires an IP address.
address = IP address of the interface.
link
Displays link related traffic.
mgcp
Displays Media Gateway Control Protocol related traffic.
address = IP address of the interface.
rip
Displays Routing Information Protocol related traffic.
address = IP address of the interface.
sip
Displays Session Initiation Protocol related traffic.
address = IP address of the interface.
stp
Displays Spanning Tree Protocol related traffic.
tcp
Displays Transmission Control Protocol related traffic.
address = IP address of the interface.
address:port = IP address
port = Port of the interface
Example: adit 3500# debug portmon 1 rip
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-11
Privileged Mode
debug trace
Use the debug trace command allows the user to configure trace settings.
Note: Immediately after this command is issued, any trace that falls into the filter parameter will be
displayed. To turn the monitoring off, you must issue a no debug trace command. See no debug
trace command on page 3-16.
Syntax:
# debug trace {cas|pri|sip} {enable|tx|rx}
Field
Definition
cas
Enable Channel Associated Signaling (CAS) tracing.
Note: Not supported on the Adit 3104.
pri
Enable Primary Rate Interface (PRI) tracing.
Note: Not supported on the Adit 3104.
sip
Enable Session Initiation Protocol (SIP) tracing.
enable
Enable the trace.
tx
Enable trace in the transmit direction.
rx
Enable trace in the receive direction.
Example: adit 3500# debug trace cas enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. Note: This command can be entered in any Configuration mode with the same result.
Syntax:
# end
Example: adit 3500# end
Username:
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing ), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
# exit
Example: adit 3500# exit
adit 3500>
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
help
Use the help command to display the help information for this command. Note: This can also be
accomplished with a ?. This command can be entered in any configuration mode.
Syntax:
# help
or
Syntax:
# ?
Example: adit 3500# help
?
Display all commands
clear
Clear command
configure
Switch to Configure mode
copy
Configures device database
date
Display time/date
debug
Debug the system
end
Exit to User mode
exit
Exit to User mode
help
Display all commands
history
Display past entered commands
log
Configure logging settings
no
Disable a feature
ping
Ping a remote host
reload
Reboot the system
show
Show various system information
traceroute
Traceroute to a remote host
upgrade
Upgrade firmware from a local computer
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-13
Privileged Mode
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
# history
Example: adit 3500# history
debug trace sip rx
no debug trace
no debug trace rx
no debug trace sip
no debug trace
no debug trace sip
debug trace
date
end
enable
configure terminal
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-14
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
log clear
Use the log clear command to clear the history of the log.
Syntax:
# log clear {all|firewall|pri|sip|system|t1|lcc}
Field
Definition
all
Clear the entire event log.
firewall
Clear firewall event log.
pri
Clear PRI event log.
Note: Not supported on the Adit 3104.
sip
Clear SIP event log.
system
Clear system event log.
t1
Clear T1 event log.
(Adit 3104, Adit 3200, Adit 3500 only.)
lcc
Clear Link Cross-Connect (LCC) event log.
(MSR only.)
Example: adit 3500# log clear firewall
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-15
Privileged Mode
no debug
no debug portmon
Use the no debug portmon command to stop the Packet Monitor (portmon) process. To configure
a debug command, see the debug command on page 3-5.
Syntax:
# no debug portmon
Example: adit 3500# no debug portmon
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no debug trace
Use the no debug trace command to stop the trace process. To configure a debug trace, see the
debug trace command on page 3-12.
Syntax:
# no debug trace {cas|pri|sip}
Field
Definition
cas
Remove trace CAS functions.
Note: Not supported on the Adit 3104.
pri
Remove trace PRI functions.
Note: Not supported on the Adit 3104.
sip
Remove trace SIP functions.
Example: adit 3500# no debug trace sip
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-16
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
ping
Use the ping command to send a sequence of ICMP echo request packets to the specified host. If the
host variable is omitted, and you are in Privileged mode, the router prompts you for additional
information. Note: The ping command verifies a connection and is a very important troubleshooting
tool.
Syntax:
# ping {address [-i time] [-l size] [-n count]
[-w timeout]|stop}
Field
Definition
address
IP address of the host to ping.
-i time
Specifies the intervals between pings.
Range is 0 - 600000 milliseconds.
-l size
Specifies the size of the ping requests packets to be sent.
Range 64 - 1518.
-n count
Specifies the number of ping requests to be sent.
Range 1-1000. Default is 4.
-w timeout
Specifies the time to wait for a response before sending the next ping
request packet. Timeout is given in seconds. Range 1-600000. Default
is 2 seconds.
stop
Stop the ping process.
Example: Adit 3500# ping 192.168.1.1
packet #1 has arrived
packet #2 has arrived
packet #3 has arrived
packet #4 has arrived
4 packets transmitted, 4 packets received
round-trip min/avg/max = 1/3/9 ms
Example: Adit 3500# ping 192.168.1.1 -n 2 -l 500
packet #1 has arrived
packet #2 has arrived
2 packets transmitted, 2 packets received
round-trip min/avg/max = 2/2/2 ms
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-17
Privileged Mode
reload
Use the reload command to reset the system.
CAUTION! THIS IS A SERVICE AFFECTING COMMAND.
Syntax:
# reload
Example: adit 3500# reload
Going to reboot!
Restarting system.
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-18
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show
For maneuverability through these commands, all command names in blue or italics are hyperlinked.
show alarms
show dhcp-leases
show arp
show digit-map
show caclkcd
show interface description
show config access-control
show interface ethernet
show config access-list
show interface multilink
show config controller t1
show interface serial
show config dmz-host
show ip ospf
show config host-filter
show ip ospf database
show config interface ethernet
show ip ospf interface
show config interface multilink
show ip ospf neighbor
show config interface serial
show ipsec
show config ip dhcp ethernet
show l2tpc
show config local-server
show licenses
show config nat-bypass
show log
show config network-object
show mac-address-table
show config port-trigger
show nat-fw
show config remote-admin
show port-trigger
show config security-default
show pptpc
show config security-log
show pptps
show config service
show route
show config static-dns
show running-config
show config time-range
show service
show config voice-port fxs
show users
show config voice-port trunk
show version
show controller lcc
show voice-port fxs
show controller t1
show voice-port trunk
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-19
Privileged Mode
show alarms
Use the show alarms command to display the active alarms.
Syntax:
# show alarms [t1 port|lcc number]
{alert|all|critical|info|major|minor}
Field
Definition
t1 port
Display alarms for a specific port.
Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
lcc number
Display alarms for a specific Link Cross-Connect (LCC).
MSR: Range = 1-8.
alert
Filter alert alarms (threshold crossing).
all
Display all alarms.
critical
Filter critical alarms.
info
Filter information alarms.
major
Filter major alarms.
minor
Filter minor alarms.
Example: adit 3500# show alarms major
Alarm
Alarm LOS T1 4
Alarm LOS T1 3
Alarm PRI T1 2 - Line NOT Ready
Severity
Major
Major
Major
Time
Jan 1 00:00:08 2006
Jan 1 00:00:08 2006
Jan 1 00:00:07 2006
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-20
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show arp
Use the show arp command to display the ARP (Address Resolution Protocol) table.
Syntax:
# show arp {all|address|ethernet port}
Field
Definition
all
Display entire ARP table.
address
Display ARP items of the entered IP address.
ethernet port
Display Ethernet ARP items only.
port - Define an Ethernet port number. Range 1 - 2.
Example: adit 3500# show arp ethernet 1
1
192.168.1.1
ether
Dynam
00:50:da:59:f0:25
eth_lan
Example: adit 3500# show arp 192.168.1.1
ip=192.168.1.1
flags=Dynam mac=00:50:da:59:f0:25 iface=eth_lan
Example: adit 3500# show arp all
#
IP-address
HW-type
Flags
HW-address
Iface
1
192.168.1.1
ether
Dynam
00:50:da:59:f0:25
eth-1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-21
Privileged Mode
show caclkcd
Use the show caclkcd command to display the linux kernel crash dump
Syntax:
# show caclkcd
Example: adit 3500# show caclkcd
---------------- Begin cacLKCD ----------Jan 1 2003 00:00:44 <3> openrg: unhandled page fault at pc=0x400528c0, lr=0x400
digit-map
Show digit-map settings
52890 (bad address=0x30303038, code 245)Show various interfaces
pc : [<400528c0>]
lr : [<40052890>]
No
Show l
r7 : 4006bb9c r6 : 30303038 r5 : 4006bb9c r4 : 4006bc1c
port-trigger
r3 : 30303030 r2 : 4006bc1c r1 : 4006bba5 r0 : 00000000
route
Show routing table
Flags: nzCv IRQs on FIQs on Mode USER_32 Segment user
Map the configurations to
CLI commands
User-mode stack:(0xbffffbac to 0xc0000000)
service
Display services
fba0:
00000001 0036d238 003704d0 0036d238 003704d0their privilages
versio
fbc0: 003704d4 0002e1e0 00000001 003704d0 0002e1a8 00000004 00000005 000281d4
voice-port
Show voice-port
fbe0: 4006d24d 4006d24c 4006d24c ffffffff 00000000 00rt
Show
fce0: 00024324 00469c08 00000001 00025144 00469c08 00469c08 0009575c 40050458ip address
Alarm LOS T1#2
fd00: 002c85a0 000001e3 40e88bc0 00000000 00000000 00000000 0009574c 0036c448
exit
fd60: 0036e270 00000000 00000000 00000004 00000094 bffffdbc 00000004 40033490
fd80: 00000000 00000000 00000000 00000094 0011121c 0000008c bffffdbc 00263674
fda0: 00000bfd 0000008c 0011138c ffffffff ffffffff 00000007 00111c44 feedbabe
fdc0: 00001063 00033bb6 0000004e 00000000 00000023 002c81e8 4006b010 400335dc
fde0: 00000000 00000000 00000000 002c8188 401a430c 002c8188 00000023 002c81e8
fe00: 001df753 00000000 401a4494 4003f960 001df753 001df730 002c8188 001df753
fe20: 001df730 4006b010 401a5ae4 00000023 001df730 00000000 00000000 00000000
fe40: 00000000 00000000 0000009c 00000000 065ca5ac 00000002 0000009c 00000000
fe60: 057aacc3 00000000 00000000 40047924 00000020 401bb254 40032cf0 4002ead4
fe80: 00000020 400054d0 0000009c 00000000 05a4faa0 00000002 400051a8 0000c222
fea0: 00000000 40000ca4 00000000 00000000 00000000 400051a8 0000938c 00000000
fec0: 00000039 00282fac 0000bc4c 4000c848 00000000 40000ca4 bfffff34 bfffff3c
fee0: 00000001 00000704 bfffff3c 00000001 bfffff30 00000000 00000000 4006b010
ff00: 00000000 40051048 bfffff34 401bb458 0001f828 401967e4 00000000 00000000
ff20: 0001145c 00000000 40196814 00000000 00011474 bfffffd2 00000000 bfffffde
ff40: bfffffe5 00000000 00000010 00000097 00000006 00001000 00000011 00000064
ff60: 00000003 00008034 00000004 00000020 00000005 00000006 00000007 40000000
ff80: 00000008 00000000 00000009 0001145c 0000000b 00000000 0000000c 00000000
ffa0: 0000000d 00000000 0000000e 00000000 0000000f bfffffce 00000000 00000000
ffc0: 00000000 00000000 00000000 00007635 62002f62 696e2f6f 70656e72 6700484f
ffe0: 4d453d2f 00544552 4d3d6c69 6e757800 2f62696e 2f6f7065 6e726700 00000000
---------------- End cacLKCD
-----------
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-22
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show config access-control
Use the show config access-control command to display all access control filters.
Syntax:
# show config access-control
Example: adit 3500# show config access-control
access-control id 1 apply-to lan time-range always service 1 enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show config access-list
Use the show config access-list command to display all access lists.
Syntax:
# show config access-list
Example: adit 3500# show config access-list
access-list rule 0 apply eth-lan direction in operation accept time-range 0
src-host 0.0.0.0-255.255.255.255 dst-host 0.0.0.0-255.255.255.255 service
50331673 frag none log none (enable)
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-23
Privileged Mode
show config controller t1
Use the show config controller t1 command to display the T1 information.
Syntax:
# show config controller t1 port
Field
Definition
port
T1 port to display.
Adit 3104: Value must be 1.
Adit 3500: Range 1 - 4.
Example: adit 3500# show config controller t1 1
controller t1 1
description T1 1
lbo short 133
fdl none
framing esf
linecode b8zs
loopdetect none
loopback none
idle-pattern 0x7f
no pri-group
no tdm-group
ds0-group timeslots 1-24
threshold daily ses 0
threshold daily sefs 0
threshold daily uas 0
threshold daily css 0
threshold daily les 0
threshold daily bes 0
threshold daily dm 0
threshold daily lcv 0
threshold daily pcv 0
threshold daily es 0
threshold min15 ses 0
threshold min15 sefs 0
threshold min15 uas 0
threshold min15 css 0
threshold min15 les 0
threshold min15 bes 0
threshold min15 dm 0
threshold min15 lcv 0
threshold min15 pcv 0
threshold min15 es 0
no shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
3-24
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show config dmz-host
Use the show config dmz-host command to display the DMZ information.
Syntax:
# show config dmz-host
Example: adit 3500# show config dmz-host
dmz-host 192.168.1.200 enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show config host-filter
Use the show config host-filter command to display the IP and host name filters.
Syntax:
# show config host-filter
Example: adit 3500# show config host-filter
host-filter id test ip-address 192.168.1.110 apply-to lan
time-range always
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-25
Privileged Mode
show config interface ethernet
Use the show config interface ethernet command to display the Ethernet port information.
Syntax:
# show config interface ethernet port
Field
Definition
port
Ethernet port to display. Range 1 - 2
Example: adit 3500# show config interface ethernet 1
Interface Ethernet 1
ip address 192.168.1.1 mask 255.255.255.0
description Ethernet 1
no tos ip
tos ip value 0x0
no ip dhcp auto-provision
no ip primary-dns
no ip secondary-dns
ip route-mode route
no ip default-route
no ip proxy-arp
no ip rip
ip rip receive-version 1or2
ip rip send-version 2-bcast
no firewall
metric 50
no shutdown
speed auto
full-duplex
remote-admin enable
no schedule-availability
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-26
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show config interface multilink
Use the show config interface multilink command to display the Multilink port information.
Syntax:
# show config interface multilink port
Field
Definition
port
Multilink port to display.
Adit 3104, Adit 3200, Adit 3500: Value must be 1.
MSR: Range = 1-8.
Example: adit 3500# show config interface multilink 1
Interface Multilink 1
ip address unnumbered
description Multilink 1
ip mtu auto
no ip primary-dns
no ip secondary-dns
ip route-mode napt
ip default-route enable
no ip rip
ip rip receive-version none
ip rip send-version none
no sip-alg
firewall enable
metric 0
no shutdown
no ppp authentication
no ppp encryption
no ppp username
ppp restart-timer 3
ppp time-btwn-reconnect
30
no ppp on-demand
ppp link-fragmentation 1600
no ppp qos-interleaving
no schedule-availability
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-27
Privileged Mode
show config interface serial
Use the show config interface serial command to display serial interface information.
Syntax:
# show config interface serial port
Field
Definition
port
Serial interface to display.
Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
MSR: Range = 1-8.
Example: adit 3500# show config interface serial 1
interface serial 1
encapsulation ppp
no ppp authentication
no ppp encryption
no ppp username
ppp restart-timer 3
ppp time-btwn-reconnect
30
no ppp on-demand
ip address unnumbered
description Serial 1
ip mtu auto
no ip primary-dns
no ip secondary-dns
ip route-mode napt
ip default-route enable
no ip rip
ip rip receive-version none
ip rip send-version none
no sip-alg
firewall enable
metric 0
no shutdown
no schedule-availability
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-28
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show config ip dhcp ethernet
Use the show config ip dhcp ethernet command to display the DHCP Pool.
Syntax:
# show config ip dhcp ethernet port
Field
Definition
port
Ethernet port to display. Range 1 - 2
Example: adit 3500# show config ip dhcp ethernet 1
ip dhcp pool ethernet 1
no relay
start-address 192.168.1.1
end-address 192.168.1.244
subnet-mask 255.255.255.0
lease 60
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show config local-server
Use the show config local-server command to display the local server configuration.
Syntax:
# show config local-server
Example: adit 3500# show config local-server
local-server id 0 hostname LocalHost1 time-range 0 fwd-port 160
service 16777216 enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-29
Privileged Mode
show config nat-bypass
Use the show config nat-bypass command to display the NAT Bypass entries.
Syntax:
# show config nat-bypass
Example: adit 3500# show config nat-bypass
nat-bypass ip-address 192.168.1.120 mask 255.255.255.0
nat-bypass ip-address 192.168.1.120 mask 255.255.255.0 enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show config network-object
Use the show config network-object command to display the network object configuration.
Syntax:
# show config network-object
Example: adit 3500# show config network-object
network-object id 0 description NetworkObject1 ip-address
192.168.1.200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show config port-trigger
Use the show config port-trigger command to display the port trigger information.
Syntax:
# show config port-trigger
Example: adit 3500# show config port-trigger
port-trigger service 134217730 enable
port-trigger service 16777223 enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-30
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show config remote-admin
Use the show config remote-admin command to display the remote admin configuration.
Syntax:
# show config remote-admin
Example: adit 3500# show config remote-admin
remote-admin telnet primary-port port 23
remote-admin telnet secondary-port port 8023
remote-admin telnet primary-secure-port port 992
remote-admin web primary-port port 80
remote-admin web secondary-port port 8080
remote-admin web primary-secure-port port 443
remote-admin web secondary-secure-port port 8443
no remote-admin snmp
no remote-admin icmp
no remote-admin udp
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show config security-default
Use the show config security-default command to display the security settings.
Syntax:
# show config security-default
Example: adit 3500# show config security-default
security-default typical
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show config security-log
Use the show config security-log command to display the security log.
Syntax:
# show config security-log
Example: adit 3500# show config security-log
security-log accept-in-connects enable
security-log rem-admin-attempts enable
security-log prevent-log-overrun enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-31
Privileged Mode
show config service
Use the show config service command display the current defined services.
Syntax:
# show config service
Example: adit 3500# show config service
service id 4 name service1 description test
protocol tcp server-src-port 1-1 server-dst-port 4-4
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show config static-dns
Use the show config static-dns command to display the static DNS entries.
Syntax:
# show config static-dns
Example: adit 3500# show config static-dns
static-dns hostname test1 ip-address 10.10.2.2
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show config time-range
Use the show config time-range command to display the time range configuration.
Syntax:
# show config time-range
Example: adit 3500# show config time-range
time-range id 0 name Schedule1 inactive time-segment 0 sun time-range
00:00-00:30
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-32
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show config voice-port fxs
Use the show config voice-port fxs command to display the FXS port information.
Syntax:
# show config voice-port fxs [port]
Field
Definition
port
FXS port to display.
Adit 3104: Range = 1 - 24.
Adit 3500: Range = 1 - 4.
MSR: Range = 1 - 48.
Example: adit 3500# show config voice-port fxs 1
voice-port fxs
no digit-map
dial-timeout 5
voice-port fxs 1
description Line 1
no comfort-noise
echo-cancel enable
input-gain 0
output-gain 0
signal loop-start
no per-line-logging
no shutdown
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-33
Privileged Mode
show config voice-port trunk
Use the show config voice-port trunk command display the Trunk port information.
Syntax:
# show config voice-port trunk port
Field
Definition
port
Trunk port to display. Value must be 1.
Example: adit 3500# show config voice-port trunk 1
Voice-port Trunk 1
description Trunk 1
trunk 000000005
no comfort-noise
connection t1 2
no echo-cancel
input-gain 0
output-gain 0
isdn switch-type pri-ni2
no digit-map
no registration enable
Example: adit MSR# show config voice-port trunk 1
Voice-port Trunk 1
description Trunk 1
trunk 000000005
no comfort-noise
echo-cancel enable
input-gain 0
output-gain 0
isdn switch-type pri-ni2
no digit-map
no registration enable
Supported Platforms: Adit 3500, MSR
3-34
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show controller lcc
Use the show controller lcc command to display the settings for a Link Cross Connect on the MSR
card.
Syntax:
# show controller lcc number
Field
Definition
number
Link Cross Connect number, 1-8.
Example: Adit MSR> show controller lcc 1
Settings for interface LCC 1
--------------------------Name
: LinkCC 1
Device Name
: LinkCC 1
Status
: Operational
Network
: WAN
Connection Type : Link Cross Connect
Connection
: Data
Alarm Reporting : Enabled
Supported Platforms: MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-35
Privileged Mode
show controller t1
Use the show controller t1 command displays the T1 configuration and performance information.
Syntax:
# show controller t1 port
Field
Definition
port
DS1 (T1) interface.
Adit 3104 Range = 1
Adit 3500 Range 1 - 4
Example: adit 3500# show controller t1 1
Settings for interface T1 1
--------------------------Interface name
: T1 1
Transmit status : Up
Receive status
: Up
Framing
: ESF
Clock source
: Clock Reference 1
Line Code
: B8ZS
Loop Detection
: OFF
FDL Type
: NONE
Line Length
: DSX-1 equalization for 0-133ft
Status
: Connected
Performance Threshold Settings
unavailable seconds (uas):
severely errored seconds (ses):
errored seconds (es):
severely errored frame seconds (sefs):
line errored seconds (les):
controlled slip seconds (css):
bursty errored seconds (bes):
degraded minutes (dm):
line code violations (lcv):
path code violations (pcv):
15 min
-----0
0
0
0
0
0
0
0
0
0
1 day
----0
0
0
0
0
0
0
0
0
0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
3-36
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show dhcp-leases
Use the show dhcp-leases command to display the DHCP lease table.
Syntax:
# show dhcp-leases
Example: Adit 3500# show dhcp-leases
Ethernet 1
Hostname : new-host IP:192.168.1.10 MAC:00:00:ff:ff:00:00
Type:static Expires-In:0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show digit-map
Use the show digit-map command to display the Digit Map patterns.
Syntax:
# show digit-map
Example: adit 3500# show digit-map
Index
Pattern
--------------------------------------------------------------1
[2-9]11
2
[0-1][2-9]11
3
0[#T]
4
00
5
*xx
6
011x.[#T]
7
[0-1]xxxxxxx[#T]
8
[0-1][2-9]xxxxxxxxx
9
[2-9]xxxxxxxxx
10
[2-9]xxxxxx[#T]
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-37
Privileged Mode
show interface description
Use the show interface description command to display the interface information.
Syntax:
# show interface description
Example: adit 3500# show interface description
Device
T1 1
T1 2
T1 3
T1 4
Serial 1
Ethernet 2
Ethernet 1
IPsec 0
IPsec 1
State
IP/Mask
running
running
up
up
up
0.0.0.0/255.255.255.255
disabled 0.0.0.0/0.0.0.0
running
192.168.1.1/255.255.255.0
disabled 0.0.0.0/0.0.0.0
running
192.168.1.1/255.255.255.0
Dependencies
None
None
None
None
T1 1
None
None
Serial 1
Ethernet 1
Example: Adit MSR# show interface description
Device
LinkCC 1
LinkCC 2
LinkCC 3
LinkCC 4
LinkCC 5
LinkCC 6
LinkCC 7
LinkCC 8
Serial 1
Ethernet 2
Ethernet 1
IPsec 0
IPsec 1
State
running
down
down
down
down
down
down
down
up
up
running
disabled
running
IP/Mask
0.0.0.0/255.255.255.255
194.168.1.1/255.255.0.0
192.168.1.1/255.255.255.0
0.0.0.0/0.0.0.0
192.168.1.1/255.255.255.0
Dependencies
None
None
None
None
None
None
None
None
LinkCC 1
None
None
Serial 1
Ethernet 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-38
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show interface ethernet
Use the show interface ethernet command to display the Ethernet interface information.
Syntax:
# show interface ethernet port
Field
Definition
port
Port number range 1-2.
Example: adit 3500# show interface ethernet 1
Device=Ethernet 1
State=running
IP/Mask=192.168.1.1/255.255.255.0
Dependency=None
Status: Connected; Link: 10T-HD
Tx (Packets/Bytes/Dropped/Errors)=(1910/1451643/0/0)
Rx (Packets/Bytes/Dropped/Errors)=(2239/136636/0/0)
Broadcasts (Tx/Rx)=(0/0) Multicasts=0 Collisions=0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show interface multilink
Use the show interface multilink command to display the configuration of the Multilink.
Syntax:
# show interface multilink port
Field
Definition
port
Multilink port number.
Adit 3104, Adit 3200, Adit 3500: Value must be 1.
MSR: Range is 1-8.
Example: adit 3500# show interface multilink 1
Device=mlink-1
State=down
Dependency=t1-1,t1-4
Status: Disconnected
IP/Mask=Unnumbered
Example: adit MSR# show interface multilink 1
Device=mlink-1
State=down
Dependency=LCC1,LCC3
Status: Disconnected
IP/Mask=Unnumbered
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-39
Privileged Mode
show interface serial
Use the show interface serial command to display the configuration of the serial interface.
Syntax:
# show interface serial port
Field
Definition
port
Serial interface.
Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
MSR: Range = 1-8.
Example: adit 3500# show interface serial 1
Device=Serial 1
State=up
IP/Mask=0.0.0.0/255.255.255.255
Dependency=T1 1
Status: Reconnecting...
Tx (Packets/Bytes/Dropped/Errors)=(556/6672/0/0)
Rx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)
Example: adit MSR# show interface serial 3
Device=Serial 1
State=up
IP/Mask=0.0.0.0/255.255.255.255
Dependency=LCC1
Status: Reconnecting...
Tx (Packets/Bytes/Dropped/Errors)=(3332/39984/0/0)
Rx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)
Supported Platforms: Adit 3104, Adit 3500, MSR
3-40
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show ip ospf
Use the show ip ospf command to display the general OSPF routing process information.
Syntax:
# show ip ospf
Example: adit 3500# show ip ospf
Routing Process "ospf 0" with ID 192.168.1.1
Process uptime is 28 minutes
Process bound to VRF default
Conforms to RFC2328, and RFC1583Compatibility flag is disabled
Supports only single TOS(TOS0) routes
Supports opaque LSA
Supports Graceful Restart
SPF schedule delay 5 secs, Hold time between two SPFs 10 secs
Refreshtimer 10 secs
Number of incomming current DD exchange neighbors 0/5
Number of outgoing current DD exchange neighbors 0/5
Number of external LSA 0. Checksum 0x000000
Number of opaque AS LSA 0. Checksum 0x000000
Number of router LSA 0
Router LSA database is unlimited.
Number of network LSA 0
Network LSA database is unlimited.
Number of non-default summary LSA 0
Summary LSA database is unlimited.
Number of asbr summary LSA 0
ASBR Summary LSA database is unlimited.
Number of non-default external LSA 0
External LSA database is unlimited.
Number of LSA originated 0
Number of LSA received 0
Number of areas attached to this router: 0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-41
Privileged Mode
show ip ospf database
Use the show ip ospf database command to display information related to the OSPF database for
a specific router. The various forms of this command deliver information on defined OSPF link
state advertisements.
3-42
Syntax:
# show ip ospf database {setting}
Syntax:
# show ip ospf database {adv-router address|self-originate}
Syntax:
# show ip ospf database network link-state-id
Syntax:
# show ip ospf database router {link-state-id|adv-router
address|self-originate}
Syntax:
# show ip ospf database summary [link-state-id] [adv-router
address|self-originate]
Field
Definition
adv-router address
Displays all the LSAs of the specified router. If no IP address is
entered, the local router information will be displayed (same as selforiginate).
link-state-id
Portion of the Internet environment that is being described by the
advertisement. The value entered depends on the advertisement's LS
type. It must be entered in the form of an IP address. When the link
state advertisement is describing a network, the link-state-id can take
one of two forms:
1. The network's IP address (as in type 3 summary link advertisements
and in autonomous system external link advertisements).
2. A derived address obtained from the link state ID. (Note that
masking a network links advertisement's link state ID with the
network's subnet mask yields the network's IP address.)
When the link state advertisement is describing a router, the link state
ID is always the described router's OSPF router ID.
When an autonomous system external advertisement (LS Type = 5) is
describing a default route, its link state ID is set to Default Destination
(0.0.0.0).
network
Displays information only about the network LSAs.
router
Displays information only about the Router LSAs.
self-originate
Displays only self-originated LSAs (from the local router).
summary
Displays information on.ly about the summary LSAs.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
Example: adit 3500# show ip ospf database
Router Link States (Area 0.0.0.1)
Link ID
192.168.3.1
192.168.3.255
ADV Router
192.168.3.1
192.168.3.255
Age Seq#
CkSum Link count
313 0x800000c1 0x4978 1
568 0x8000003a 0xa6c0 1
Net Link States (Area 0.0.0.1)
Link ID
192.168.3.251
ADV Router
192.168.3.255
Age Seq#
CkSum
388 0x80000003 0xbcec
Example: adit 3500# show ip ospf database self-originate
Router Link States (Area 0.0.0.1)
Link ID ADV Router Age Seq# CkSum Link count
192.168.3.255 192.168.3.255 420 0x8000003a 0xa6c0 1
Net Link States (Area 0.0.0.1)
Link ID ADV Router Age Seq# CkSum
192.168.3.251 192.168.3.255 240 0x80000003 0xbcec
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-43
Privileged Mode
show ip ospf interface
Use the show ip ospf interface command to display OSPF related interface information.
Syntax:
# show ip ospf interface {ethernet port|serial port|multilink
port}
Field
Definition
ethernet port
Display information on the Ethernet interface.
port = 1 or 2
serial port
Display information on the serial interface.
Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
MSR: Range = 1-8.
multilink port
Display information on the Multilink interface.
Adit 3104, Adit 3500, MSR: Value must be 1
Example: adit 3500# show ip ospf interface ethernet 1
Ethernet 1 is up, line protocol is up
Internet Address 192.168.254.202, Mask 255.255.255.0, Area 0.0.0.0
AS 201, Router ID 192.168.99.1, Network Type BROADCAST, Cost: 10
Transmit Delay is 1 sec, State OTHER, Priority 1
Designated Router id 192.168.254.10, Interface address 192.168.254.10
Backup Designated router id 192.168.254.28, Interface addr 192.168.254.28
Timer intervals configured, Hello 10, Dead 60, Wait 40, Retransmit 5
Hello due in 0:00:05
Neighbor Count is 8, Adjacent neighbor count is 2
Adjacent with neighbor 192.168.254.28 (Backup Designated Router)
Adjacent with neighbor 192.168.254.10 (Designated Router)
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-44
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show ip ospf neighbor
Use the show ip ospf neighbor command to display OSPF neighbor information.
Syntax:
# show ip ospf neighbor [interface address|neighbor-id|detail]
Field
Definition
interface address
Optional parameter. Enter interface IP address to define display.
neighbor-id
Optional parameter. Enter neighbor IP address to define display.
detail
Optional parameter. Enable display of detailed information.
Example: adit 3500# show ip ospf neighbor
ID
Pri
10.199.199.137 1
172.16.48.1
1
172.16.48.200
1
10.199.199.137 5
State
Dead Time
FULL/DR
0:00:31
FULL/DROTHER 0:00:33
FULL/DROTHER 0:00:33
FULL/DR
0:00:33
Address
192.168.80.37
172.16.48.1
172.16.48.200
172.16.48.189
Interface
Ethernet1
Fddi0
Fddi0
Fddi0
Example: adit 3500# show ip ospf neighbor 10.199.199.137
Neighbor 10.199.199.137, interface address 192.168.80.37
In the area 0.0.0.0 via interface Ethernet0
Neighbor priority is 1, State is FULL
Options 2
Dead timer due in 0:00:32
Link State retransmission due in 0:00:04
Neighbor 10.199.199.137, interface address 172.16.48.189
In the area 0.0.0.0 via interface Fddi0
Neighbor priority is 5, State is FULL
Options 2
Dead timer due in 0:00:32
Link State retransmission due in 0:00:03
Example: adit 3500# show ip ospf neighbor detail
Neighbor 192.168.5.2, interface address 10.225.200.28
In the area 0 via interface GigabitEthernet1/0/0
Neighbor priority is 1, State is FULL, 6 state changes
DR is 10.225.200.28 BDR is 10.225.200.30
Options is 0x42
LLS Options is 0x1 (LR), last OOB-Resync 00:03:08 ago
Dead timer due in 00:00:36
Neighbor is up for 00:09:46
Index 1/1, retransmission queue length 0, number of retransmission 1
First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)
Last retransmission scan length is 1, maximum is 1
Last retransmission scan time is 0 msec, maximum is 0 msec
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-45
Privileged Mode
show ipsec
Use the show ipsec command to display the IPSec Connections or the connection configuration
information.
Syntax:
# show ipsec [vpn_ipsecconnection-id]
Field
Definition
connection-id
Enter the name of a connection.
Example: adit 3500#
vpn_ipsec
vpn_ipsec
vpn_ipsec
vpn_ipsec
show ipsec
0
1
2
3
Example: adit 3500# show ipsec vpn_ipsec2
Device = test State = Enabled tatus = No VPN software license
Schedule Availability = Always
Remote Tunnel Endpoint Address = 192.168.1.200
Security Association Mode = Tunnel
Remote Subnet = None
Route NetBOIS Broadcasts = Enabled
Dead Period Detection = Disable
Remote Broadcast Address = 192.168.1.200
Key Exchange Method = Automatic
Auto_Reconnect = Enabled
Mode = Main Mode
Negotiation Attempts = 3
Rekey Life Time = 3600 sec
Rekey Margin = 540
Rekey Fuzz Percent = 100
Peer Authentication = Shared Secret
Shared Secret = mysecret
Encryption = 3des,
Hash = md5,sha1,
Group = grp2,grp5,
Lifetime = 28000 sec
Use PFS = Enabled
Group = Same group as phase 1
AH Transform = md5,sha1,
ESP Encryption Transform = esp-3des,
ESP Authentication Transform = esp-md5,esp-sha1,
IP Compression = Disabled
Default Route = Disabled
RIP = Enabled
RIP Listen Msg. = RIPv1/2
RIP Send Msg. = None
OSPF = Disabled
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-46
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show l2tpc
Use the show l2tpc command to display the Layer 2 Tunneling Protocol Connections or the
connection configuration information.
Syntax:
# show l2tpc [l2tpc connection-id]
Field
Definition
connection-id
Enter the name of a connection.
Example: adit 3500# show l2tpc
l2tp#0
l2tp#1
l2tp#2
Example: adit 3500# show l2tpc l2tpc 1
Device = L2TPC#1
State = Disable
Status = Disabled
Schedule Availability = Always
MTU = 1456
Time Between Reconnect Attempts = 0
Restart Timer = 0
PPP
On Demand = Disable
User Name =
Authentication =
Encryption = MPPE-40
MPPE-128
(Stateless)
IP Address =
Mask = 0.0.0.0
DNS Primary = 192.168.2.10
Secondary =
Routing Mode = NAPT
SIP Alg = Enabled
Default Route = Enabled
Rip = Enabled
RIP Listen Msg = none
RIP Send Msg = none
Firewall = Enabled
Additional IP Address
IP Address
Mask
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-47
Privileged Mode
show licenses
Use the show licenses command to display all enabled feature keys.
Syntax:
# show licenses
Example: adit 3500# show licenses
VPN
SIP
MGCP
G729A
license
license
license
license
=
=
=
=
No
Yes
No
Yes
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-48
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show log
Use the show log command to display the current events on the system.
Syntax:
# show log {firewall|pri|sip|system|t1 port|lcc number}
[severity]
Field
Definition
firewall
Filter firewall alarms
pri
Display PRI logs. Note: This is not supported on the Adit 3104.
sip
Display SIP logs.
system
Filter general system alarms
t1 port
Display event log for a specific T1 port.
Adit 3104: Value must be 1.
Adit 3500: Range = 1-4.
lcc number
Display event log for a specific Link Cross-Connect (LCC).
MSR: Range = 1-8.
severity
alert - Filter alert alarms (threshold crossing)
all - Display all alarms.
critical - Filter critical alarms (service affecting)
info - Filter informational alarms
major - Filter major alarms (service affecting)
minor - Filter minor alarms (non-service affecting)
Example: adit 3500# show log t1 1 minor
System
System
System
System
System
System
System
System
Log
Log
Log
Log
Log
Log
Log
Log
Message
Message
Message
Message
Message
Message
Message
Message
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
1
1
1
1
1
1
1
1
00:00:08
00:00:04
01:19:13
00:57:12
00:56:52
00:56:34
00:56:09
00:00:04
2003
2003
2003
2003
2003
2003
2003
2003
kern.err
kern.err
kern.err
kern.err
kern.err
kern.err
kern.err
kern.err
T1
T1
T1
T1
T1
T1
T1
T1
ALARM:
ALARM:
ALARM:
ALARM:
ALARM:
ALARM:
ALARM:
ALARM:
Alarm
Alarm
Alarm
Alarm
Alarm
Alarm
Alarm
Alarm
LOS
LOS
LOS
LOS
LOS
LOS
LOS
LOS
T1#1
T1#1
T1#1
T1#1
T1#1
T1#1
T1#1
T1#1
Major
Major
Major
Major
Major
Major
Major
Major
received
received
received
received
received
received
received
received
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-49
Privileged Mode
show mac-address-table
Use the show mac-address-table command to display the current MAC addresses (LAN\WAN).
Syntax:
# show mac-address-table
Example: adit 3500# show mac-address-table
Ethernet 1 mac= 00:00:00:ff:ff:ff
Ethernet 2 mac= 00:00:00:ff:ff:fd
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show nat-fw
Use the show nat-fw command to display the current NAT and firewall connection table.
Syntax:
# show nat-fw
Example: adit 3500# show nat-fw
Number Content
1
TCP 11.0.0.4
36104<--> 172.15.16.1
36104[31.0.0.6 5516 ]
TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1320 pkts 7 ppp100 Outgoing BY FTP
2
TCP 11.0.0.4
36103<--> 172.15.16.1
36103[31.0.0.6 21
]
TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1182 pkts 20 FTP child: Yes ppp100 Outgoing
3
TCP 11.0.0.4
36102<--> 172.15.16.1
36102[31.0.0.6 5515 ]
TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1320 pkts 7 ppp100 Outgoing BY FTP
4
TCP 11.0.0.4
36101<--> 172.15.16.1
36101[31.0.0.6 21
]
TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1182 pkts 20 FTP child: Yes ppp100 Outgoing
5
UDP 172.15.16.2
28015<--> 172.15.16.2
28015[*.*.*.*
*] ttl
79 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP
6
UDP 172.15.16.2
28014<--> 172.15.16.2
28014[*.*.*.*
*] ttl
79 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP
7
UDP 172.15.16.2
28013<--> 172.15.16.2
28013[*.*.*.*
*] ttl
77 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP
8
UDP 172.15.16.2
28012<--> 172.15.16.2
28012[*.*.*.*
*] ttl
77 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP
9
UDP 172.15.16.2
28011<--> 172.15.16.2
28011[*.*.*.*
*] ttl
75 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP
10
UDP 172.15.16.2
28010<--> 172.15.16.2
28010[*.*.*.*
*] ttl
75 sec bytes 0 pkts 0 ppp100 Outgoing CLONABLE UNINIT BY SIP
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-50
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show port-trigger
Use the show port-trigger command to display the port trigger information.
Syntax:
# show port-trigger
Example: adit 3500# show port-trigger
Service ID:134217730
Trigger protocol: UDP
dst_end=1701
Enable
Service Name:L2TP
port: src_start=0
src_end=0
Service ID:16777223
Trigger protocol: UDP
dst_end=69
Enable
Service Name:TFTP
port: src_start=1024
src_end=65535
dst_start=1701
dst_start=69
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-51
Privileged Mode
show pptpc
Use the show pptps command to display the PPTP connections or the PPTP connection details.
Syntax:
# show pptpc [pptpc connection-id]
Field
Definition
connection-id
Enter the name of a connection.
Example: adit 3500# show pptpc
PPTP#0
PPTP#1
Example: adit 3500# show pptpc pptpc 1
Device = PPTPC-1
State = Disable
Status = Disabled
Schedule Availability = Always
MTU = 1460
Time Between Reconnect Attempts = 0
Restart Timer = 600
PPP
On Demand = Disable
User Name =
Authentication = CHAP
Encryption = MPPE-40
MPPE-128
(Stateless)
IP Address =
Mask = 0.0.0.0
DNS Primary =
Secondary =
Routing Mode = Route
SIP Alg = Enabled
Default Route = Disabled
Firewall = Disabled
Additional IP Address
IP Address
Mask
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-52
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show pptps
Use the show pptps command to display the PPTP Server settings.
Syntax:
# show pptps
Example: adit 3500# show pptps
state = Enable
status = Invalid vpn license
Idle_Time = 1200
Authentication =
MS-CHAP MS-CHAPv2
PAP
Encryption = MPPE-40
MPPE-128
(Stateless)
Remote IP Address Range = 192.168.1.245 - 192.168.1.254
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show route
Use the show route command to display the routing table.
Syntax:
# show route
Example: adit 3500# show route
Destination
192.168.1.0/24
192.168.1.0/24
Gateway
*
*
Flags Metric Interface
U
50
Ethernet 1
U
51
IPsec 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-53
Privileged Mode
show running-config
Use the show running-config command to display the current configuration of the system.
Syntax:
# show running-config
Example: adit 3500# show running-config
ip host adit3500
log system notify none
log security notify none
log t1 notify none
clock source 1 t1 1
clock source 2 none
controller t1 1
description T1 #1
lbo short 133
fdl none
framing esf
linecode b8zs
loopdetect none
loopback none
idle-pattern 0x7f
no pri-group
no tdm-group
no ds0-group
.
.
.
interface ethernet 1
ip address 192.168.1.150 mask 255.255.255.0
description LAN Hardware Ethernet Switch
ip mtu auto
no tos ip
tos ip 0x0
no ip primary-dns
no ip secondary-dns
no ip default-route
no ip proxy-arp
no ip rip
ip rip receive-version 1or2
ip rip send-version 2-bcast
no sip-alg
no firewall
metric 50
no shutdown
speed auto
full-duplex
remote-admin enable
no schedule-availability
.
.
.
ip dhcp pool ethernet 1
start 192.168.1.1
end 192.168.1.244
subnet-mask 255.255.255.0
lease 60
ip dhcp pool ethernet 2
no dhcp pool
3-54
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
no radius-server
voice-port trunk 1
description Trunk 1
no comfort-noise
connection t1 2
no echo-cancel
input-gain 0
output-gain 0
isdn switch-type primary-ni2
voice-port fxs 1
description Line 1
no comfort-noise
echo-cancel enable
input-gain 0
output-gain 0
dial-timeout 5
signal loop-start
.
.
.
voice-codec g711ulaw ptime 20
voice-codec g711alaw ptime 20
voice-codec g729 ptime 20
dial-peer voice pots trunk 1
fax protocol none
modem protocol none
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729
no sip-authentication
dial-peer voice pots fxs 1
fax protocol none
modem protocol none
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729
no calling-party-disconnect
call-waiting enable
no caller-id
no sip-authentication
.
.
.
voice-service sip
transport udp
sip-port 5060
rtp-base-port 28000
dtmf rfc2833
no proxy-server
no outbound-proxy
privacy-mode none
no prack
early-media auto
proxy-type generic
calling-party-disconnect 900
feature-mode local
no conference
no call-fwd-indication
phone-number 10
session-timer 1800
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-55
Privileged Mode
session-timer refresher uac
no session-timer mode
redundancy type none
redundancy ttl 3600
redundancy rollback-timer 300
redundancy advanced-timeout 2
redundancy advanced-retries 3
no filter-incoming
Example: adit MSR# show running-config
! Start of commands to eliminate default configuration
no voice-port trunk 1
interface serial 1
shutdown
exit
no interface serial 1
! End of commands to eliminate default configuration
ip host adit_MSR
ip domain-name home
log system notify none
log security notify none
log t1 notify none
no log pri
log pri buffer-size 50
log pri buffer-fill 0
log pri display 1
no log sip
log sip buffer-size 250
log sip buffer-fill 0
log sip level detailed
log sip display 1
clock source 1 none
clock source 2 none
interface ethernet 1
ip address 10.0.0.3 mask 255.255.255.0
description Ethernet 1
no tos ip
tos ip value 0x0
no ip dhcp auto-provision
no ip primary-dns
no ip secondary-dns
ip route-mode route
no ip default-route
no ip proxy-arp
no ip rip
ip rip receive-version 1or2
ip rip send-version 2-bcast
no firewall
metric 50
no shutdown
speed auto
full-duplex
remote-admin enable
3-56
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
no schedule-availability
ip ospf authentication null
exit
interface ethernet 2
ip address auto
description Ethernet 2
ip mtu auto
ip dhcp auto-provision
no ip primary-dns
no ip secondary-dns
ip route-mode napt
ip default-route enable
no ip proxy-arp
no ip rip
ip rip receive-version 1or2
ip rip send-version 2-bcast
sip-alg enable
firewall enable
metric 40
no shutdown
speed auto
full-duplex
no schedule-availability
ip ospf authentication null
exit
no ip dhcp pool ethernet 1
no ip dhcp pool ethernet 2
no radius-client
voice-port
tos sip value 0xdc
tos rtp value 0xb8
digit-map short-timeout 4
digit-map long-timeout 16
digit-map pattern 1 [2-9]11
digit-map pattern 2 [0-1][2-9]11
digit-map pattern 3 0[#T]
digit-map pattern 4 00
digit-map pattern 5 *xx
digit-map pattern 6 011x.[#T]
digit-map pattern 7 [0-1]xxxxxxx[#T]
digit-map pattern 8 [0-1][2-9]xxxxxxxxx
digit-map pattern 9 [2-9]xxxxxxxxx
digit-map pattern 10 [2-9]xxxxxx[#T]
digit-map pattern 11 101xxxx.[#T]
exit
voice-port trunk 1
description Trunk 1
trunk 000000005
no comfort-noise
echo-cancel enable
input-gain 0
output-gain 0
isdn switch-type pri-ni2
no digit-map
no registration enable
exit
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-57
Privileged Mode
voice-port fxs
no digit-map
dial-timeout 5
exit
voice-port fxs 1
description Line 1
no comfort-noise
echo-cancel enable
input-gain 0
output-gain 0
signal loop-start
no per-line-logging
no shutdown
exit
.
.
.
voice-port fxs 48
description Line 48
no comfort-noise
echo-cancel enable
input-gain 0
output-gain 0
signal loop-start
no per-line-logging
no shutdown
exit
voice-codec g711ulaw ptime 20
voice-codec g711alaw ptime 20
dial-peer voice pots trunk 1 1
fax-protocol none
modem-protocol none
codec preference 1 g711ulaw
codec preference 2 g711alaw
no block-out-caller-id
no sip-authentication
exit
voice-service sip
gateway-ip 0.0.0.0
transport udp
sip-port 5060
rtp-base-port 28000
dtmf rfc2833
no proxy-server
no outbound-proxy
privacy-mode none
no prack
early-media auto
proxy-type generic
calling-party-disc 900
feature-mode local
no conference
phone-number max-size 10
session-timer timeout 1800
session-timer refresher uac
no session-timer mode
registration rate 60
registration expire 3600
3-58
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
registration retry-timeout 500
registration tries 2
registration failed-time 60
registration window-size 10
no registration ignore-negotiated enable
redundancy type none
fax-protocol-t38 signaling sdp-preferred
fax-protocol-t38 ecs redundant
fax-protocol-t38 ls-redundancy 3
fax-protocol-t38 hs-redundancy 0
exit
port-trigger service 134217730 enable
port-trigger service 16777223 enable
remote-admin telnet primary-port port 23
remote-admin telnet secondary-port port 8023
remote-admin telnet primary-secure-port port 992
remote-admin web primary-port port 80
remote-admin web secondary-port port 8080
remote-admin web primary-secure-port port 443
remote-admin web secondary-secure-port port 8443
no remote-admin snmp
no remote-admin icmp
no remote-admin udp
security-default typical
no date summer-time
snmp-server community public ro
snmp-server community private rw
snmp-server enable
no dynamic-dns interface
no dynamic-dns mail-exchanger
no mail-server authentication
mail-server port 25
no vlan
vlan
tag-all disable
port-priority Ethernet 1.1 0
pvid Ethernet 1.1 1
no port-dot1q Ethernet 1.1
port-protocol-filter disable Ethernet 1.1
port-priority Ethernet 2.1 0
pvid Ethernet 2.1 1
no port-dot1q Ethernet 2.1
port-protocol-filter disable Ethernet 2.1
exit
! IPSec General Config
ipsec replay
ipsec authentication-retries 5 delay 60
no ipsec log ike auto-key
no ipsec log ike ike-int
no ipsec log ike ike-msg
no ipsec log ike msg-byte
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-59
Privileged Mode
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
ipsec
log
log
log
log
log
log
log
log
log
log
log
log
log
log
log
log
log
log
log
ike msg-enc-dec
ike msg-inp
ike msg-outp
ike pri-key
ike rej-packet
ipsec atc
ipsec emvc
ipsec etc
ipsec ip-ctc
ipsec irtmc
ipsec mirl
ipsec rc
ipsec rtmc
ipsec satmc
ipsec tc
ipsec tsmc
ipsec ttc
ipsec usc
ipsec vrp
pptps
ppp authentication
ppp encryption
start-address 250.250.5.245
end-address 250.250.5.254
exit
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
3-60
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show service
Use the show service command to display all service information. Note: The following example,
is only a portion of the list.
Syntax:
# show service
Example: adit 3500# show service
Group:
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
Service
Trigger
.
.
.
Basic Web Utilities
ID:16777216
Service Name:All Traffic
protocol: NO PROTOCOL port: src_start=0
src_end=0
dst_start=0
dst_end=0
ID:16777217
Service Name:DNS
protocol: TCP
port: src_start=53
src_end=53
dst_start=53
dst_end=53
ID:16777217
Service Name:DNS
protocol: TCP
port: src_start=1024
src_end=65535
dst_start=53
dst_end=53
ID:16777217
Service Name:DNS
protocol: UDP
port: src_start=53
src_end=53
dst_start=53
dst_end=53
ID:16777217
Service Name:DNS
protocol: UDP
port: src_start=1024
src_end=65535
dst_start=53
dst_end=53
ID:16777218
Service Name:FTP
protocol: TCP
port: src_start=0
src_end=0
dst_start=21
dst_end=21
ID:16777219
Service Name:HTTP
protocol: TCP
port: src_start=0
src_end=0
dst_start=80
dst_end=80
ID:16777220
Service Name:HTTP Secondary
protocol: TCP
port: src_start=0
src_end=0
dst_start=8080
dst_end=8080
ID:16777221
Service Name:HTTPS
protocol: TCP
port: src_start=0
src_end=0
dst_start=443
dst_end=443
ID:16777222
Service Name:HTTPS Secondary
protocol: TCP
port: src_start=0
src_end=0
dst_start=8443
dst_end=8443
ID:16777223
Service Name:TFTP
protocol: UDP
port: src_start=1024
src_end=65535
dst_start=69
dst_end=69
ID:16777224
Service Name:IMAP
protocol: TCP
port: src_start=0
src_end=0
dst_start=143
dst_end=143
ID:16777225
Service Name:NNTP
protocol: TCP
port: src_start=0
src_end=0
dst_start=119
dst_end=119
ID:16777226
Service Name:Ping
protocol: ICMP port: src_start=0
src_end=0
dst_start=0
dst_end=0
ID:16777227
Service Name:POP3
protocol: TCP
port: src_start=0
src_end=0
dst_start=110
dst_end=110
ID:16777228
Service Name:SNMP
protocol: UDP
port: src_start=0
src_end=0
dst_start=161
dst_end=161
ID:16777229
Service Name:SMTP
protocol: TCP
port: src_start=0
src_end=0
dst_start=25
dst_end=25
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-61
Privileged Mode
show users
Use the show users command to display all users on this system.
Syntax:
# show users
Example: adit 3500# show users
Provisioned User List
User-1 : admin
Access: ADMIN <User-2 : pauljones Access: ADMIN
Active CLI Users
User-1 : admin
Access:ADMIN
Authen:Config
User-2 : admin
Access:ADMIN
Authen:Config
from IP:192.168.1.1
from Console
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
show version
Use the show version command to display the version for the hardware, software and firmware.
The Admin level user will be provided with more information than Manager and Monitor levels.
Software features are listed along with enabled status.
Syntax:
# show version
Example: adit 3500# show version
Application Version: 1.4.0
Compilation Time: Mon Jan 5 2007 16:12:48
FPGA Version: 1.00
Board Version: 1 003-1215-0100
IXP400 Software Release: 1_4 SQA4_1
MSP:
82530 - 60 channels
Image File Name: TGW_v5_03_cdma.axf
API Version
: 2.1.0
Source IP Addr : 192.168.1.150
Voice Slot 1 : FXS Card Present: Rev 5.00 VIP
Vendor: Turin Networks
Product Features:
SIP enabled.
G729A enabled.
3-62
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
Example: Adit MSR# show version
Application Version: 2.0.0.5
Compilation Time: Thu Jan 31 2008 13:48:42
FPGA Version: 0.04
Boot Version: 1.14
Board Version: 0 003-1756-0001
Flash Size: 32M bytes
Memory Size: 64M bytes
IXP400 Software Release: 1_4 SQA4_1
MSP:
82610 - 100 channels
Image File Name: TGW_v5_05.axf
API Version
: 2.1.0
Source IP Addr : 10.10.4.202
MSR Card Slot: 5
CLEI Code: SITRAANBAA
Product Features:
VPN enabled.
SIP enabled.
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-63
Privileged Mode
show voice-port fxs
Use the show voice-port fxs command to display the FXS voice port information.
Syntax:
# show voice-port fxs
Example: adit 3500# show voice-port fxs
Registration Address: 172.32.1.15
SIP Proxy: Yes
Proxy Address: 172.32.1.18
* Line UID
PhoneStatus RegisStatus RX/TX/Lost(Pkts) Jitter Overflow
---------------------------------------------------------------------------Y 1
3035550001
Idle
Registered
Y 2
3035550002
Idle
Registered
Y 3
3035550003
Idle
Registered
Y 4
3035550004
Idle
Registered
Example: adit MSR# show voice-port fxs
Registration Address: 172.32.1.15
SIP Proxy: Yes
Proxy Address: 172.32.1.18
* Line UID
PhoneStatus RegisStatus RX/TX/Lost(Pkts) Jitter Overflow CrossConnect
-----------------------------------------------------------------------------------------Y 1
3035550001
Idle
Registered
Connected
Y 2
3035550002
Idle
Registered
Connected
Y 3
3035550003
Idle
Registered
Connected
Y 4
3035550004
Idle
Registered
Connected
Y 5
3035550005
Idle
Registered
Connected
Y 6
3035550006
Idle
Registered
Connected
Y 7
3035550007
Idle
Registered
Connected
Y 8
3035550008
Idle
Registered
Connected
.
.
.
Supported Platforms: Adit 3104, Adit 3500, MSR
3-64
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
show voice-port trunk
Use the show voice-port trunk command to display the trunk voice port information.
Syntax:
# show voice-port trunk port
Field
Definition
port
Adit 3500: DS1 (T1) interface. Value must be 1.
MSR: Link Cross Connect (LCC). Range = 1-8.
Example: adit 3500# show voice-port trunk 1
trunk-1 t1-1 does not exist
******************************* PRI 2 *************************************
Channel no
Internal Call Id
Q931 Connection Id
Tdm TimeSlot
Call State
---------------------------------------------------------------------------1
-1
-1
-1
INACTIVE
2
-1
-1
-1
INACTIVE
3
-1
-1
-1
INACTIVE
4
-1
-1
-1
INACTIVE
5
-1
-1
-1
INACTIVE
6
-1
-1
-1
INACTIVE
7
-1
-1
-1
INACTIVE
8
-1
-1
-1
INACTIVE
9
-1
-1
-1
INACTIVE
10
-1
-1
-1
INACTIVE
11
-1
-1
-1
INACTIVE
12
-1
-1
-1
INACTIVE
13
-1
-1
-1
INACTIVE
14
-1
-1
-1
INACTIVE
15
-1
-1
-1
INACTIVE
16
-1
-1
-1
INACTIVE
17
-1
-1
-1
INACTIVE
18
-1
-1
-1
INACTIVE
19
-1
-1
-1
INACTIVE
20
-1
-1
-1
INACTIVE
21
-1
-1
-1
INACTIVE
22
-1
-1
-1
INACTIVE
23
-1
-1
-1
INACTIVE
trunk-1 t1-3 does not exist
trunk-1 t1-4 does not exist
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-65
Privileged Mode
Example: adit MSR# show voice-port trunk 1
******************************* PRI 1 ***************************************
Channel no
Internal Call Id
Q931 Connection Id
Tdm TimeSlot
Call State
------------------------------------------------------------------------------1
-1
-1
-1
INACTIVE
2
-1
-1
-1
INACTIVE
3
-1
-1
-1
INACTIVE
4
-1
-1
-1
INACTIVE
5
-1
-1
-1
INACTIVE
6
-1
-1
-1
INACTIVE
7
-1
-1
-1
INACTIVE
8
-1
-1
-1
INACTIVE
9
-1
-1
-1
INACTIVE
10
-1
-1
-1
INACTIVE
11
-1
-1
-1
INACTIVE
12
-1
-1
-1
INACTIVE
13
-1
-1
-1
INACTIVE
14
-1
-1
-1
INACTIVE
15
-1
-1
-1
INACTIVE
16
-1
-1
-1
INACTIVE
17
-1
-1
-1
INACTIVE
18
-1
-1
-1
INACTIVE
19
-1
-1
-1
INACTIVE
20
-1
-1
-1
INACTIVE
21
-1
-1
-1
INACTIVE
22
-1
-1
-1
INACTIVE
23
-1
-1
-1
INACTIVE
trunk 1 LCC#2 does not exist
trunk 1 LCC#3 does not exist
trunk 1 LCC#4 does not exist
trunk 1 LCC#5 does not exist
trunk 1 LCC#6 does not exist
trunk 1 LCC#7 does not exist
trunk 1 LCC#8 does not exist
Supported Platforms: Adit 3500, MSR
3-66
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Privileged Mode
traceroute
Use the traceroute command to trace a route to a remote host.
Syntax:
# traceroute
Syntax:
# traceroute {address|hostname|stop}
Field
Definition
address
IP address of the remote host.
hostname
Host name of the remote host.
stop
Stop the traceroute process.
Example: Adit 3500# traceroute to 192.168.1.200
(192.168.1.200), 10 hops max
1 192.168.1.200 (192.168.1.200) 10.500 ms 1.013 ms 0.926 ms
Traceroute: Destination Reached
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
upgrade
Use the upgrade command to upgrade the system software. Note: This requires the TFTP software to
be running in the background.
Syntax:
# upgrade ip-address address file filename [check]
Field
Definition
address
IP address of the TFTP server with the software upgrade file.
filename
Name of the software file to load on the system, this is a .rmt file.
check
Check only. Verify that the file is a software image file. Do not store
the file as the software image
Example: adit 3500# upgrade ip-address 192.168.1.1 file adit3500_1_0.rmt
WARNING: Upgrade starting. Do NOT issue new commands until done
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
3-67
Privileged Mode
3-68
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
4
Global Configuration Mode
The Global Configuration Mode allows commands to be entered directly to the router configuration.
From this level, additional configuration modes can be entered. Once configuration is complete, use the
exit/end command to return to the Privileged Mode prompt.
This Mode is entered with the # configure terminal command from the Privileged mode.
The Global Configuration Mode is represented by the (config)# prompt.
Note: The Trunk option is not available on the Adit 3104.
In This Chapter
„
Commands for Entering Configuration Submodes
„
Global Configuration Commands
Global Configuration Mode
Commands for Entering Configuration Submodes
4-2
Configuration Mode
Link to Command
Prompt Displayed
Controller LCC
controller lcc
(config-cont-lcc-{n})#
Controller T1
controller t1
(config-cont-t1-{n})#
DHCP server pool
ip dhcp pool ethernet
(config-dhcp-eth-{n})#
Dial Peer FXS
dial-peer voice pots fxs
(config-dpeer-fxs)#
Dial Peer Trunk
dial-peer voice pots trunk
(config-dpeer-trk)#
Dial Peer VoIP
dial-peer voice voip
(config-dpeer-voip)#
Ethernet Interface
interface ethernet
(config-int-eth-{n})#
MLPPP Interface
interface multilink
(config-int-mlink-{n})#
Serial Interface
interface serial
(config-int-ser-{n})#
VPN IPSEC
ipsec
(config-ipsec-{n})#
VPN L2TP Client
l2tpc
(config-l2tpc-{n})#
OSPF
router ospf
(config-ospf)#
VPN PPTP Client
pptpc
(config-pptpc-{n})#
VPN PPTP Server
pptps
(config-pptps)#
RADIUS
radius-client
(config-radius)#
VLAN (Global)
vlan (global)
(config-vlan)#
VLAN (Port)
vlan (vlan-id)
(config-vlan-{n})#
Voice Port (Global)
voice-port (global)
(config-vport)#
Voice Port (FXS)
voice-port fxs
(config-vport-fxs-{n})#
Voice Port (Trunk)
voice-port trunk
(config-vport-trunk-{n})#
Voice Service SIP
voice-service sip
(config-voice-serv-sip)#
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
Global Configuration Commands
• access
• l2tpc
• access-control
• local-server
• access-list
• log
• authentication login
• mail-server
• clock source
• nat-bypass
• controller lcc
• network-object
• controller t1
• no commands
• date
• port-trigger service
• delete local-server
• pptpc
• dial-peer voice
• pptps
• dmz-host
• radius-client
• do
• remote-admin
• dynamic-dns
• router ospf
• end
• security-default
• exit
• security-log
• help
• service
• history
• snmp-server
• host-filter
• static-dns
• interface ethernet
• time-range
• interface multilink
• username
• interface serial
• vlan (global)
• ipsec
• vlan (vlan-id)
• ip dhcp pool ethernet
• voice-codec
• ip domain-name
• voice-port (global)
• ip host
• voice-port trunk
• key
• voice-service sip
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-3
Global Configuration Mode
Global Configuration Commands
access
Use the access command to enable remote access via LAN or WAN. To disable remote access, see no
access command on page 4-36.
Syntax:
(config)# access {lan|wan} enable
Field
Definition
lan
Enable remote access via the LAN.
wan
Enable remote access via the WAN.
Example: (config)# access lan enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
access-control
Use the access-control command to configure an access (scheduler) rule for the system. To remove a
rule, see no access-control command on page 4-36.
Syntax:
(config)# access-control name apply-to {lan|object-name}
time-range {always|schedule-id} service service-id
Field
Definition
name
Enter a name for the Access Control (Scheduler Rule), with a
maximum of 64 characters.
lan
Apply this scheduler rule to the LAN interface.
object-name
Enter the Network Object name to apply the rule to.
always
Apply this rule always. Default.
schedule-id
A configured schedule to apply this rule.
service-id
Enter the service number to apply the rule to.
Note: The Service ID number can be found with the show service
command, on page 3-61
Example: (config)# access-control AccessControl_1 apply-to lan time-range
always service 16777220
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
access-list
Use the access-list command to configure the advanced filtering entries. To delete an access list, see no
access-list command on page 4-37.
Syntax:
(config)# access-list rule {new|rule-name} apply {eth-lan|
eth-wan|final|initial|ppp-wan} direction {in|out} operation
{accept|accept-packet|drop|reject} time-range {always|
schedule-name} src-host {address|address-range|any} dst-host
{address|address-range|any} service service-id frag
{enable|none} log {enable|none}
Field
Definition
new
Create a new Access list rule. Note: Do not use this new option when
using an Automated Provisioning System.
rule-name
Enter an existing rule name to apply this command to.
eth-lan
Ethernet LAN interface.
eth-wan
Ethernet WAN interface.
initial
Initial rules defined here will be applied first to the interface.
final
Final rules defined here will be applied last to the interface.
ppp-wan
PPP WAN interface.
in
Filter the incoming traffic only.
out
Filter the outgoing traffic only.
accept
Allow access to packets that match the criteria defined. The data transfer
session will be handled using Stateful Packet Inspection (SPI), meaning
that other packets matching this rule will be automatically allowed access.
accept-list
Allow access to packets that match the criteria defined. The data transfer
session will not be handled using SPI, meaning that other packets
matching this rule will not be automatically allowed access. This can be
useful, for example, when creating rules that follow broadcasting.
drop
Deny access to packets that match the source and destination IP addresses
and service ports defined above.
reject
Deny access to packets that match the criteria defined, and send an ICMP
error or a TCP reset to the origination peer.
always
This rule will always take effect. Default.
schedule-name
Apply the defined schedule times to this rule.
src-host
The source address of packets sent or received from the LAN computer.
This entry is mandatory when denying a rule.
address - enter the source IP address
address-range - enter a range of source IP addresses
any - allow any IP address
dst-host
Destination address of packets sent/received from the network object.
address - enter the destination IP address
address-range - enter a range of destination IP addresses.
any - allow any IP addresses.
service-id
Enter the service number to apply the rule to. Note: Service ID number
can be displayed with the show service command, on page 3-61.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-5
Global Configuration Mode
Global Configuration Commands
Field
Definition (Continued)
frag
enable - Enable fragmentation.
none - Do not allow fragmentation.
log
Enable or disables logging of packets matched by this rule.
Example: (config)# access-list rule new apply eth-lan direction in
operation accept time-range always src-host any dst-host any
service 16777220 frag none log none
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
authentication login
Use the authentication login command to use RADIUS for login authentication. To remove an
authentication login, see no authentication login command on page 4-37.
Syntax:
(config)# authentication login use-radius
Example: (config)# authentication login use-radius
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
clock source
Use the clock source command to define the primary and secondary clock source.
Syntax:
(config)# clock {1|2} source {none|t1 port}
Field
Definition
1|2
Sets the interface to the following clock source.
1 = Clock 1, primary clock source
2 = Clock 2, secondary clock source
none
Sets the clock source to internal.
t1 port
Sets the clock source to a DS1. Range is 1-4.
Example: (config)# clock 1 source t1 2
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
Not supported by the MSR card
4-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
controller lcc
Use the controller lcc command to allow access to the Controller LCC configuration commands. See
Chapter 5, Configuration - LCC Controller Mode for commands in this mode.
Syntax:
(config)# controller lcc number
Field
Definition
number
Selects the Link Cross Connect. Range = 1-8
Example: (config)# controller lcc 1
(config-cont-lcc-1)#
Supported Platforms: MSR
controller t1
Use the controller t1 command to allow access to the Controller T1 configuration commands. See
Chapter 6, Configuration - T1 Controller Mode for commands in this mode.
Syntax:
(config)# controller t1 port
Field
Definition
port
Selects the T1 (DS1) port.
Adit 3104 Range = 1
Adit 3500 Range 1 - 4
Example: (config)# controller t1 1
(config-cont-t1-1)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-7
Global Configuration Mode
Global Configuration Commands
date
date auto-time-update
Use the date auto-time-update command to automatically update the clock from the defined
server. To stop the auto update, see no date auto-time-update command on page 4-37.
Syntax:
(config)# date auto-time-update protocol {ntp|tod} server
address1 [address2] [address3] [address4] update-every hours
Field
Definition
ntp
Network Time Protocol protocol. Default for Adit 3000.
tod
Time of Day protocol.
address1, address2, Enter the IP Address of the Time Server. Additional addresses may be
...
added for backup if the primary Time Server fails.
hours
Sets the amount of time between resets. Range 1-480 hours. Default is
24 hours.
Example: (config)# date auto-time-update protocol ntp server 192.168.1.1
update-every 24
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Note: By default, Time of Day management for the MSR is provided by the Adit 600 controller.
date set
Use the date set command to manually set the internal clock.
Syntax:
(config)# date set hh:mm:ss dd mm yyyy
Field
Definition
hh:mm:ss
Set the time in the 24 hour format hh:mm:ss
hh = hours, range is 0 - 23
mm = minutes, range is 0 - 59
ss = seconds, range is 0 - 59
dd
dd = day, range is 1 - 31
mm
mm = month, range is 1 - 12
yyyy
Enter current year (example 2006). Range 1970 - 2037.
Example: (config)# date set 05:00:00 04 17 2006
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Note: By default, Time of Day management for the MSR is provided by the Adit 600 controller.
Use this command with the MSR only if you are using NTP or another time service and need to
manually adjust the time due to a loss of contact with the server.
4-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
date summer-time
Use the date summer-time command to update the clock for daylight savings time. To stop the
update for daylight saving, see no date summer-time command on page 4-38.
Note: Default settings are start: 3/28 time 00:00, end: 10/28 time 01:00.
Syntax:
(config)# date summer-time smonth sday shh:mm emonth eday ehh:mm
offset
Field
Definition
smonth and emonth
The month in which daylight savings time starts (smonth) or ends
(emonth). Range is 1-12.
sday and eday
The day on which daylight savings time starts (sday) or ends (eday).
Range is 1-31.
shh:mm and ehh:mm Start time (shh:mm) and end time (ehh:mm).
hh = hour, range 00:59
mm = minutes, range 00:59
offset
This is an optional parameter, to set the offset of the daylight savings
time. Range is 1-120, with a default of 60.
Example: (config)# date summer-time 03 28 00:00 10 28 01:00 60
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Note: By default, Time of Day management for the MSR is provided by the Adit 600 controller.
Use this command with the MSR only if you are using NTP or another time service and need to
manually adjust the time due to a loss of contact with the server.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-9
Global Configuration Mode
Global Configuration Commands
date timezone
Use the date timezone command to set the time zone and the number of hours from the GMT.
Syntax:
(config)# date timezone hh:mm
Field
Definition
hh
Hour offset from GMT. Range is from -12 to +12, with a default of 0.
mm
Minute offset from GMT in minutes. Range is from 00 to 59, with a
default of 00. This is used for half hour time zones.
Example: (config)# date timezone -05:00
The example will set the time zone offset to be -5:00 from GMT (Greenwich Mean Time),
which equates to Eastern Standard Time.
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Note: By default, Time of Day management for the MSR is provided by the Adit 600 controller.
Use this command with the MSR only if you are using NTP or another time service and need to
manually adjust the time due to a loss of contact with the server.
delete local-server
Use the delete local-server command to delete a local server.
Syntax:
(config)# delete local-server server-id
Field
Definition
server-id
Server ID.
Example: (config)# delete local-server 192.168.1.200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
dial-peer voice
dial-peer voice pots fxs
Use the dial-peer voice pots fxs command to allow access to the Dial Peer Voice FXS
configuration commands. See Chapter 8, Configuration - Dial Peer FXS Mode for commands in
this mode. For the no counterpart of this command see no dial-peer voice pots fxs command on
page 4-38.
Syntax:
(config)# dial-peer voice pots fxs port
Field
Definition
port
Selects the FXS port to configure.
Adit 3104: Range is 1-24.
Adit 3500: Range is 1-4.
MSR: Range is 1-48.
Example: (config)# dial-peer voice pots fxs 1
(config-dpeer-fxs)#
Supported Platforms: Adit 3104, Adit 3500, MSR
dial-peer voice pots trunk
Use the dial-peer voice pots trunk command to allow access to the Dial Peer Voice Trunk
configuration commands. See Chapter 9, Configuration - Dial Peer Trunk Mode for commands in
this mode. For the no counterpart of this command see no dial-peer voice pots trunk command on
page 4-38. Note: This command is not supported on the Adit 3104.
Syntax:
(config)# dial-peer voice pots trunk port dest-port
Field
Definition
port
Select the trunk port to configure.
Adit 3500: Range = 1-4
MSR: Value must be 1.
dest-port
Set destination port. Range is 1-30.
Example: (config)# dial-peer voice pots trunk 2 1
(config-dpeer-trk)#
Supported Platforms: Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-11
Global Configuration Mode
Global Configuration Commands
dial-peer voice voip
Use the dial-peer voice voip command to allow access to the Dial Peer Voice VoIP configuration
commands. See Chapter 10, Configuration - Dial Peer VoIP Mode for commands in this mode. For
the no counterpart of this command see no dial-peer voice voip command on page 4-39.
Syntax:
(config)# dial-peer voice voip trunk
Field
Definition
trunk
Enter trunk number. Range is 1-50.
Example: (config)# dial-peer voice voip 1
(config-dpeer-voip)#
Supported Platforms: Adit 3104, Adit 3500, MSR
dmz-host
Use the dmz-host command to configure the DMZ host. To remove a DMZ host, see no dmz-host
command on page 4-39.
Syntax:
(config)# dmz-host address enable
Field
Definition
address
The IP address of the DMZ host.
Example: (config)# dmz-host 10.10.200.1 enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-13
Global Configuration Mode
Global Configuration Commands
dynamic-dns
Use the dynamic-dns commands to configure the DNS Dynamic entries. To disable Dynamic DNS, see
no dynamic-dns command on page 4-39.
dynamic-dns backup-mx
Use the dynamic-dns backup-mx command to enable the Dynamic DNS backup MX.
Syntax:
(config)# dynamic-dns backup-mx enable
Example: (config)# dynamic-dns backup-mx enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
dynamic-dns interface
Use the dynamic-dns interface command to define the Dynamic DNS connection to update.
Syntax:
(config)# dynamic-dns interface {eth-2|mlink-1|ser-n}
Field
Definition
eth-2
Select Ethernet port 2.
mlink-1
Select Multilink port 1.
ser-n
Select serial interface 1-4.
Example: (config)# dynamic-dns interface ser-1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-14
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
dynamic-dns mail-exchanger
Use the dynamic-dns mail-exchanger command to define the Dynamic DNS mail exchanger.
Syntax:
(config)# dynamic-dns mail-exchanger mail-exchanger
Field
Definition
mail-exchanger
Enter your mail exchange server address, to redirect all E-mails
arriving at your Dyndns address to your mail server.
Example: (config)# dynamic-dns mail-exchanger 10.10.1.0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
dynamic-dns offline
Use the dynamic-dns offline command to enable Dynamic DNS offline.
Syntax:
(config)# dynamic-dns offline enable
Example: (config)# dynamic-dns offline enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
dynamic-dns username
Use the dynamic-dns username command to define the Dynamic DNS username.
Syntax:
(config)# dynamic-dns username username
Field
Definition
username
Enter your Dyndns user name.
Example: (config)# dynamic-dns username JohnD
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-15
Global Configuration Mode
Global Configuration Commands
dynamic-dns wildcard
Use the dynamic-dns wildcard command to enable the Dynamic DNS wildcard.
Syntax:
(config)# dynamic-dns wildcard enable
Example: (config)# dynamic-dns wildcard enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
end
Use the end command to exit the current configuration mode. Note: This command can be entered in
any configuration mode with the same result.
Syntax:
(config)# end
Example: (config)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config)# exit
Example: (config)# exit
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-16
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
help
Use the help command to display the help information for this command. Note: This can also be
accomplished with a ?. This command can be entered in any configuration mode.
Syntax:
(config)# help
or (config)# ?
Example: (config)# help
?
access
access-control
access-list
authentication
clock
controller
date
delete
dial-peer
dmz-host
do
dynamic-dns
end
exit
help
history
host-filter
interface
ip
ipsec
key
l2tpc
local-server
log
mail-server
nat-bypass
network-object
no
port-trigger
pptpc
.
.
Display all commands
Permit access via LAN/WAN
Configure access control entries
Define access list
Configure authentication method
Internal clock setting
Enter Controller context
Set time/date
Delete a feature
Enter Dial peer context
Configure the DMZ host
Run Privileged and User mode commands
Configure DNS Dynamic entries
End Configuration mode session
Exit from Configuration mode
Display all commands
Display past entered commands
Configure IP/hostname filtering entries
Configure Ethernet or Serial interface
Configure general IP parameters
Configure IPSEC parameters
Enable software feature keys
Configure L2TP client options
Add local server
Configure logging
Configure mail server options
Configure NAT bypass
Configure network objects
Disable features
Configure port trigger
Configure PPTP client options
.
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-17
Global Configuration Mode
Global Configuration Commands
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config)# history
Example: (config)# history
clock source 1 none
date
date set 12:12:06 15 12 2006
date set 3:4:3
date set 12:12:20
date set 0:0:1
date summer-time 3 28 00:00 10 28 01:00 60
date timezone +03:00
dial-peer voice pots trunk 1 1
dial-peer voice voip
dmz-host 192.168.1.100 enable
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-18
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
host-filter
Use the host-filter command to configure the IP/host name filtering entries. To delete a host filter, see
no host-filter command on page 4-40.
Syntax:
(config)# host-filter id filter-id {ip-address address|hostname
hostname} apply-to {lan|network-object object-id} time-range
{always|schedule-id}
Field
Definition
filter-id
Enter a filter ID name.
address
Enter the host IP address.
hostname
Enter a host name for the rule.
lan
Apply the filter the LAN interface.
network-object
object-id
Apply the filter to a defined network object.
always
Set the time range to always.
schedule-id
Enter defined schedule ID name with schedule to apply to this filter.
Example: (config)# host-filter id filterID ip-address 192.168.1.100
apply-to lan time-range always
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
interface ethernet
Use the interface ethernet command to allow access to the Ethernet interface configuration commands.
See Chapter 11, Configuration - Ethernet Interface Mode for commands in this mode.
Syntax:
(config)# interface ethernet port
Field
Definition
port
Ethernet port. Range 1-2.
Example: (config)# interface ethernet 1
(config-int-eth-1)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-19
Global Configuration Mode
Global Configuration Commands
interface multilink
Use the interface multilink command to allow access to the MLPPP configuration commands. See
Chapter 12, Configuration - Multilink Interface Mode for commands in this mode. To delete a Multilink
interface, see no interface multilink command on page 4-42.
Syntax:
(config)# interface multilink group-number
Field
Definition
group-number
Enter multilink group number.
Adit 3104, Adit 3200, Adit 3500: Value must be 1.
MSR: Range = 1-8.
Example: (config)# interface multilink 1
(config-int-mlink-1)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
interface serial
Use the interface serial command to allow access to the serial interface configuration commands. See
Chapter 13, Configuration - Serial Interface Mode for commands in this mode. To delete a serial
interface, see no interface serial command on page 4-42.
Syntax:
(config)# interface serial port
Field
Definition
port
Adit 3104: Value must be 1.
Adit 3200, Adit 3500: Range = 1-4.
MSR: Range = 1-8.
Example: (config)# interface serial 1
(config-int-ser-1)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-20
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
ipsec
Use the ipsec commands to create an IPSec connection and to configure IPSec global settings. See
Chapter 14, Configuration - IPSec Mode for additional commands in this mode.
ipsec authentication-retries
Use the ipsec authentication-retries command to enable the block-ip feature. To disable block-ip, see
no ipsec authentication-retries command on page 4-40.
Syntax:
(config)# ipsec authentication-retries number delay seconds
Field
Definition
number
The maximum number of retries for authentication.
Range is 0-2147483647, with a default of 5.
seconds
The time delay after retries. Range is 0-2147483647 seconds, with a
default of 60.
Example: (config)# ipsec authentication-retries 10 delay 45
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ipsec key generate key
Use the ipsec key generate key command to generate a new public RSA key.
Syntax:
(config)# ipsec key generate key
Example: (config)# ipsec key generate key
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-21
Global Configuration Mode
Global Configuration Commands
ipsec log ike
Use the ipsec log ike command to enable Internet Key Exchange (IKE) related logs. To disable IKE
logging, see no ipsec log ike command on page 4-40
Syntax:
(config)# ipsec log ike {auto-key|ike-int|ike-msg|msg-byte|
msg-enc-dec|msg_inp|msg-outp|pri-key|rej-packet}
Field
Definition
auto-key
Enable verbose automatic keying.
ike-int
Enable verbose IKE IPSec interaction.
ike-msg
Print all IKE message ignoring rate limit.
msg-byte
Enable message’s raw byte option.
msg-enc-dec
Enable message’s encryption and decryption.
msg_inp
Enable message’s input structure.
msg-outp
Enable message’s output structure.
pri-key
Enable verbose private key.
rej-packet
Enable verbose IKE reject packets.
Example: (config)# ipsec log ike msg-outp
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-22
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
ipsec log ipsec
Use the ipsec log ipsec command to enable IPSec related logs. To disable IPSec logging, see no ipsec
log ipsec command on page 4-41.
Syntax:
(config)# ipsec log ipsec {atc|emvc|etc|ip-ctc|irtmc|mirl
|rc|rtmc|satmc|tc|tsmc|ttc|usc|vrp}
Field
Definition
atc
Authentication Transforms Code.
emvc
Even More Verbose Output.
etc
Encryption Transforms Code.
ip-ctc
IP Compression Transforms Code.
irtmc
Internal Route Table Manipulation Code.
mirl
Print all IPSec Messages Ignoring Rate Limit.
rc
Receive Code.
rtmc
Radij Tree Manipulation Code.
satmc
Secure Association Table Manipulation Code.
tc
Tunneling Code.
tsmc
Transform Selection and Manipulation Code.
ttc
Tunneling Transmit Code.
usc
User-Space Communication Code.
vrp
Verbose Rejected Packets.
Example: (config)# ipsec log ipsec tc
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ipsec net-to-host
Use the ipsec net-to-host command to create a network-to-host connection.
Syntax:
(config)# ipsec net-to-host remote-ip {address|any} pre-share
secret
Field
Definition
address
Specify a remote tunnel endpoint address.
any
Allow any IP address.
secret
Enter a pre-shared secret string.
Example: (config)# ipsec net-to-host remote-ip 192.168.1.200 pre-share
mysecret
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-23
Global Configuration Mode
Global Configuration Commands
ipsec net-to-net
Use the ipsec net-to-net command to create a network-to-network connection.
Syntax:
(config)# ipsec net-to-net remote-ip {address|any} remote-subnet
{ip address mask mask|any} pre-share secret
Field
Definition
remote-ip
address - Enter the remote tunnel endpoint address.
any - Allow any IP address.
remote-subnet
address - Enter an IP address if it is a remote IP.
mask - Enter an IP mask if it is a remote IP.
any - Allow any IP address.
secret
Enter a pre-shared secret string.
Example: (config)# ipsec net-to-host remote-ip 10.10.1.1 pre-share
mysecret
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ipsec replay
Use the ipsec replay command to enable anti-replay protection. To disable anti-replay protection, see
no ipsec replay command on page 4-41.
Syntax:
(config)# ipsec replay
Example: (config)# ipsec replay
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ipsec vpn_ipsec
Use the ipsec vpn_ipsec command to allow access to configuration commands for a specific IPSec
connection. See Chapter 14, Configuration - IPSec Mode for commands in this mode. To delete this
interface, see no ipsec vpn_ipsec command on page 4-42.
Note: This connection must be created first. See ipsec net-to-host command on page 4-23 and ipsec netto-net command on page 4-24 to create an IPSec connection.
Syntax:
(config)# ipsec vpn_ipsec connection-id
Field
Definition
connection-id
Enter the name of a connection.
Example: (config)# ipsec vpn_ipsec 1
(config-ipsec-1)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-24
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
ip dhcp pool ethernet
Use the ip dhcp pool ethernet command to allow access to the DHCP configuration commands. See
Chapter 7, Configuration - DHCP Pool Ethernet Mode for commands in this mode. For the no
counterpart, see no ip dhcp pool ethernet command on page 4-43.
Syntax:
(config)# ip dhcp pool ethernet port
Field
Definition
port
Selects the Ethernet port to configure. Range is 1-2.
Example: (config)# ip dhcp pool ethernet 1
(config-dhcp-eth-1)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip domain-name
Use the ip domain-name command to sets system domain name.
Syntax:
(config)# ip domain-name name
Field
Definition
name
Enter the domain name of the device.
Example: (config)# ip domain-name mydomain.com
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip host
Use the ip host command to set the host name for this device.
Syntax:
(config)# ip host hostname
Field
Definition
hostname
Enter the name of the host. Default is adit3500, adit3104, or aditMSR
(depending on the platform).
Example: (config)# ip host gateway1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-25
Global Configuration Mode
Global Configuration Commands
key
Use the key command to enable a specific keyed feature. To acquire a feature key code, contact Turin
Networks Customer Support. To disable a keyed feature, see the no key command on page 4-43.
Syntax:
(config)# key key-code
Field
Definition
key-code
Enter the key code to enable the feature.
Example: (config)# key q0B8yma2IsSL+1BarY0u
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
l2tpc
Use the l2tpc command to allow access to the VPN L2TP Connection configuration commands. See
Chapter 15, Configuration - L2TPC Mode for commands in this mode. To delete an existing connection,
see the no l2tpc command on page 4-43.
Syntax:
(config)# l2tpc {l2tpc connection-id|address address [ipsec
local-secret secret] [local-secret secret]}
Field
Definition
connection-id
Enter the connection ID (number).
address
Enter the IP address of the destination.
ipsec
Optional parameter. Directs IPSec to create an L2TP connection.
Requires the local-secret option.
local-secret secret
Optional parameter. Enter a secret password used to authenticate
L2TP connection. Maximum number of characters is 96.
Example: (config)# l2tpc l2tpc 1
(config-l2tpc-1)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-26
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
local-server
Use the local-server command to configure the local server entries. To delete a local server, see the no
local-server command on page 4-44.
Syntax:
(config)# local-server id {name|new} {ip-address address
|hostname hostname} time-range {always|schedule-name} fwd-port
port service service-id
Field
Definition
name
Enter a name of the server.
new
Select New to create a new local server.
address
Enter an IP address of the local server.
hostname
Enter a host name of the server.
always
Set the time range to
schedule-name
Enter a defined schedule to be applied to the server.
port
Enter a forwarding port.
service-id
Enter the service number to apply the rule to. Note: The Service ID
number is displayed with the show service command, on page 3-61
Example: (config)# local-server id Boulder-server ip-address 10.10.2.100
time-range always fwd-port 2 service 16777220
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-27
Global Configuration Mode
Global Configuration Commands
log
log lcc buffer
Use the log lcc buffer command to set the buffer size allowed for the Link Cross-Connect (LCC)
log buffer.
Syntax:
(config)# log lcc buffer kilobytes
Field
Definition
kilobytes
Set the size of the LCC log buffer. Range is 1 - 256 KB. Default is
16KB.
Example: (config)# log lcc buffer 24
Supported Platforms: MSR
log lcc notify
Use the log lcc notify command to set the remote Link Cross-Connect (LCC) notify level.
Syntax:
(config)# log lcc notify {error|info|ip-address address
|none|warn}
Field
Definition
error
Notify for error level.
info
Notify for information level.
ip-address address
Enter IP address of remote system to notify.
none
No notification.
warn
Notify for warning level.
Example: (config)# log lcc notify warn
Supported Platforms: MSR
4-28
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
log pri
Use the log pri command to configure PRI logging.
Syntax:
(config)# log pri {buffer-fill {0|1}|buffer-size kilobytes
|display number|enable}
Field
Definition
buffer-fill {0|1}
Define the method of loading the buffer.
0 = Circular Buffer - the buffer will store a continuous stream of data
by starting again at the beginning of the buffer after reaching the end.
Default.
1 = Fill Until Full - the buffer will fill until it is full. The user will
have to clear the log manually.
buffer-size kilobytes Configure the PRI log size. Range is 1-250 KB, with a default of 100
KB.
display number
Defines the number of lines per message. 0 = full
enable
Enable PRI logging.
Example: (config)# log pri buffer-fill 0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
log security buffer
Use the log security buffer command to set the buffer size allowed for the security log buffer.
Syntax:
(config)# log security buffer kilobytes
Field
Definition
kilobytes
Set the size of the Security log buffer. Range is 1-256 KB. Default is
16KB.
Example: (config)# log security buffer 24
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-29
Global Configuration Mode
Global Configuration Commands
log security notify
Use the log security notify command to set the remote security notify level.
Syntax:
(config)# log security notify {error|info|ip-address address
|none|warn}
Field
Definition
error
Notify for error level.
info
Notify for information level.
ip-address address
Enter IP address of remote system to notify.
none
No notification.
warn
Notify for warning level.
Example: (config)# log security notify warn
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
log sip
Use the log sip command to configure SIP logging. To stop a SIP log, see no log sip command on
page 4-44.
Syntax:
(config)# log sip {buffer-fill {0|1}|buffer-size kilobytes
|display number|enable|level {detail|non-detailed}}
Field
Definition
buffer-fill {0|1}
Define the method of loading the buffer.
0 = Circular Buffer - the buffer will store a continuous stream of data
by starting again at the beginning of the buffer after reaching the end.
Default.
1 = Fill Until Full - the buffer will fill until it is full. The user will
have to clear the log manually.
buffer-size kilobytes Configure the SIP log size. Range is 1 - 250 KB, with a default of 100
KB.
display number
Defines the number of lines per message. 0 = full
enable
Enable SIP logging.
level
Defines the logging level.
detailed - Set logging level to detail.
non-detailed - Set logging level to non-detail
Example: (config)# log sip buffer-fill 0
Supported Platforms: Adit 3104, Adit 3500, MSR
4-30
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
log system buffer
Use the log system buffer command to set the buffer size allowed for the system log buffer.
Syntax:
(config)# log system buffer kilobytes
Field
Definition
kilobytes
Set the size of the system log buffer. Range is 1 - 256 KB. Default is
16KB.
Example: (config)# log system buffer 24
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
log system notify
Use the log system notify command to set the remote system notify level.
Syntax:
(config)# log system notify {error|info|ip-address address
|none|warn}
Field
Definition
error
Notify for error level.
info
Notify for information level.
ip-address address
Enter IP address of remote system to notify.
none
No notification.
warn
Notify for warning level.
Example: (config)# log system notify error
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-31
Global Configuration Mode
Global Configuration Commands
log t1 buffer
Use the log t1 buffer command to set the buffer size allowed for the T1 log buffer.
Syntax:
(config)# log t1 buffer kilobytes
Field
Definition
kilobytes
Set the size of the T1 log buffer. Range is 1 - 256 KB. Default is
16KB.
Example: (config)# log t1 buffer 24
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
log t1 notify
Use the log t1 notify command to set the remote T1 notify level.
Syntax:
(config)# log t1 notify {error|info|ip-address address
|none|warn}
Field
Definition
error
Notify for error level.
info
Notify for information level.
ip-address address
Enter IP address of remote system to notify.
none
No notification.
warn
Notify for warning level.
Example: (config)# log t1 notify warn
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
4-32
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
mail-server
mail-server authentication enable
Use the mail-server authentication enable command to enable the outgoing mail server
authentication. To disable the mail-server authentication, see no mail-server authentication
command on page 4-44.
Syntax:
(config)# mail-server authentication enable
Example: (config)# mail-server authentication enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
mail-server from-address
Use the mail-server from-address command to set the outgoing mail server from an e-mail
address.
Syntax:
(config)# mail-server from-address address
Field
Definition
address
Enter the "from e-mail" address.
Example: (config)# mail-server from-address xxx@turinnetworks.com
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
mail-server host
Use the mail-server host command to set the outgoing mail server.
Syntax:
(config)# mail-server host address
Field
Definition
address
Outgoing mail server IP address.
Example: (config)# mail-server host 192.168.1.1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-33
Global Configuration Mode
Global Configuration Commands
mail-server port
Use the mail-server port command to set the outgoing mail server port.
Syntax:
(config)# mail-server port port
Field
Definition
port
Enter the port number. Range is 0 - 65535. Default is 25.
Example: (config)# mail-server port 25
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
mail-server username
Use the mail-server username command to set the username and password for the mail server.
Syntax:
(config)# mail-server username username password password
Field
Definition
username
Enter the mail server username.
password
Enter the mail server password for this server.
Example: (config)# mail-server username server10 password secret10
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-34
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
nat-bypass
Use the nat-bypass command to create and enable a NAT bypass rule. To disable NAT Bypass, see no
nat-bypass command on page 4-44.
Syntax:
(config)# nat-bypass ip-address address mask mask [enable]
Field
Definition
address
Enter a NAT bypass IP address.
mask
Enter a subnet mask for the above address.
enable
Enable NAT bypass.
Note: To create the rule without enabling, do not enter this option.
Example: (config)# nat-bypass ip-address 10.10.2.1 mask 255.255.255.0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
network-object
Use the network-object command to configure a network object with the system. To delete a network
object, see no network-object command on page 4-45.
Syntax:
(config)# network-object id object-id description text type
{hostname hostname|ip-address address|mac-address mac-address}
Field
Definition
object-id
Enter the numerical ID for the Network Object.
text
Enter a description of the Network Element.
hostname
Enter the host name of the Network Object.
address
Enter the IP address of the Network Element.
mac-address
Enter the MAC address of the Network Element (xx:xx:xx:xx:xx:xx)
Example: (config)# network-object id 1 description Unit1 type ip-address
192.168.1.200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-35
Global Configuration Mode
Global Configuration Commands
no commands
no access
Use the access command to disable remote access via LAN or WAN. To enable remote access, see
access command on page 4-4.
Syntax:
(config)# no access {lan|wan}
Field
Definition
lan
Disable access to the unit via the LAN.
wan
Disable access to the unit via the WAN.
Example: (config)# no access lan
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no access-control
Use the no access-control command to remove an access rule for the system. To add an access rule,
see access-control command on page 4-4.
Syntax:
(config)# no access-control name
Field
Definition
name
Enter a current Access Control (Scheduler Rule).
Example: (config)# no access-control AccessControl1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-36
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
no access-list
Use the no access-list command to remove an advanced filtering entry. To add a filter, see accesslist command on page 4-5.
Syntax:
(config)# no access-list rule rule-name apply {eth-lan|eth-wan
|ppp-wan|initial|final}
Field
Definition
rule-name
Enter an existing rule name to apply this command to.
eth-lan
Ethernet LAN interface.
eth-wan
Ethernet WAN interface.
initial
Initial rules defined here will be applied first to the interface.
final
Final rules defined here will be applied last to the interface.
ppp-wan
PPP WAN interface.
Example: (config)# no access-list rule TestRule-1 apply eth-lan
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no authentication login
Use the no authentication login command to disable RADIUS for login authentication. To enable
RADIUS login authentication, see authentication login command on page 4-6.
Syntax:
(config)# no authentication login use-radius
Example: (config)# no authentication login use-radius
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no date auto-time-update
Use the no date auto-time-update command to stop the automatic update the clock from the
defined server. To enable automatic update of the clock, see date auto-time-update command on
page 4-8.
Syntax:
(config)# no date auto-time-update
Example: (config)# no date auto-time-update
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-37
Global Configuration Mode
Global Configuration Commands
no date summer-time
Use the no date summer-time command to remove daylight savings time setting. To enable
daylight savings, see date summer-time command on page 4-9.
Syntax:
(config)# no date summer-time
Example: (config)# no date summer-time
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
Not supported by the MSR
no dial-peer voice pots fxs
Use the no dial-peer voice pots fxs command denies access to the Dial Peer Voice POTS FXS
configuration commands. To allow access, see dial-peer voice command on page 4-11.
Syntax:
(config)# no dial-peer voice pots fxs port
Field
Definition
port
Selects the FXS port to configure.
Adit 3104: Range is 1-24.
Adit 3500: Range is 1-4.
MSR: Range is 1-48.
Example: (config)# no dial-peer voice pots fxs 2 1
Supported Platforms: Adit 3104, Adit 3500, MSR
no dial-peer voice pots trunk
Use the no dial-peer voice pots trunk command denies access to the Dial Peer Voice POTS trunk
configuration commands. To enable access, see dial-peer voice command on page 4-11.
Note: This command is not supported on the Adit 3104.
Syntax:
(config)# no dial-peer voice pots trunk port tag
Field
Definition
port
Select the trunk port.
Adit 3500: Range = 1-4
MSR: Value must be 1.
tag
Set destination range. Range is 1-30.
Example: (config)# no dial-peer voice pots trunk 2 1
Supported Platforms: Adit 3500, MSR
4-38
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
no dial-peer voice voip
Use the no dial-peer voice voip command denies access to the Dial Peer Voice VoIP configuration
commands. To allow access, see dial-peer voice command on page 4-11.
Syntax:
(config)# no dial-peer voice voip tag
Field
Definition
tag
Enter the tag number to denies access. Range is 1-30.
Example: (config)# no dial-peer voice voip 1
Supported Platforms: Adit 3104, Adit 3500, MSR
no dmz-host
Use the no dmz-host command to remove a DMZ host. To add a DMZ hose, see dmz-host
command on page 4-12.
Syntax:
(config)# no dmz-host address
Field
Definition
address
The IP address of the DMZ host.
Example: (config)# no dmz-host 10.10.200.1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no dynamic-dns
Use the no dynamic-dns commands to disable DNS Dynamic entries. To enable DNS Dynamic
entries, see dynamic-dns command on page 4-14.
Syntax:
(config)# no dynamic-dns {backup-mx|interface|mail-exchanger
|offline|wildcard}
Field
Definition
backup-mx
Disable DNS Dynamic Backup MX.
interface
Specify DNS Dynamic connection to update.
mail-exchanger
Remove mail exchanger.
offline
Disable DNS Dynamic offline.
wildcard
Disable DNS Dynamic wildcard.
Example: (config)# no dynamic-dns backup-mx
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-39
Global Configuration Mode
Global Configuration Commands
no host-filter
Use the no host-filter command to remove a IP host name filter entry. To add a IP host name, see
host-filter command on page 4-19.
Syntax:
(config)# no host-filter name
Field
Definition
name
Name of an existing IP host name to remove.
Example: (config)# no host-filter HostFilter1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ipsec authentication-retries
Use the no ipsec authentication-retries command to disable the block-ip feature. To enable block-ip,
see the ipsec authentication-retries command on page 4-21.
Syntax:
(config)# no ipsec authentication-retries
Example: (config)# no ipsec authentication-retries
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ipsec log ike
Use the no ipsec log ike command to disable Internet Key Exchange (IKE) related logs. To enable IKE
logging, see ipsec log ike command on page 4-22
Syntax:
(config)# no ipsec log ike {auto-key|ike-int|ike-msg|msg-byte|
msg-enc-dec|msg_inp|msg-outp|pri-key|rej-packet}
Field
Definition
auto-key
Enable verbose automatic keying.
ike-int
Enable verbose IKE IPSec interaction.
ike-msg
Print all IKE message ignoring rate limit.
msg-byte
Enable message’s raw byte option.
msg-enc-dec
Enable message’s encryption and decryption.
msg_inp
Enable message’s input structure.
msg-outp
Enable message’s output structure.
pri-key
Enable verbose private key.
rej-packet
Enable verbose IKE reject packets.
Example: (config)# no ipsec log ike msg-outp
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-40
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
no ipsec log ipsec
Use the no ipsec log ipsec command to disable IPSec related logs. To enable IPSec logging, see ipsec
log ipsec command on page 4-23
Syntax:
(config)# no ipsec log ipsec {atc|emvc|etc|ip-ctc|irtmc|mirl
|rc|rtmc|satmc|tc|tsmc|ttc|usc|vrp}
Field
Definition
atc
Authentication Transforms Code.
emvc
Even More Verbose Output.
etc
Encryption Transforms Code.
ip-ctc
IP Compression Transforms Code.
irtmc
Internal Route Table Manipulation Code.
mirl
Print all IPSec Messages Ignoring Rate Limit.
rc
Receive Code.
rtmc
Radij Tree Manipulation Code.
satmc
Secure Association Table Manipulation Code.
tc
Tunneling Code.
tsmc
Transform Selection and Manipulation Code.
ttc
Tunneling Transmit Code.
usc
User-Space Communication Code.
vrp
Verbose Rejected Packets.
Example: (config)# no ipsec log ipsec tc
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ipsec replay
Use the no ipsec authentication-retries command to disable anti-replay protection. To enable the antireplay protection, see the ipsec replay command on page 4-24.
Syntax:
(config)# no ipsec replay
Example: (config)# no ipsec replay
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-41
Global Configuration Mode
Global Configuration Commands
no ipsec vpn_ipsec
Use the no ipsec vpn_ipsec command to delete an IPSec connection.
To create an IPSec connection, see ipsec net-to-host command on page 4-23 or ipsec net-to-net
command on page 4-24
To enter an IPSec connection, for configuration see ipsec vpn_ipsec command on page 4-24.
Syntax:
(config)# no ipsec ipsec connection-id
Field
Definition
connection-id
Enter the name of a connection.
Example: (config)# no ipsec ipsec 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no interface multilink
Use the no interface multilink command denies access to the MLPPP configuration commands.
To enter the Multilink interface configuration mode, see the interface multilink command on
page 4-20.
Syntax:
(config)# no interface multilink group-number
Field
Definition
group-number
Enter multilink group number.
Adit 3104, Adit 3200, Adit 3500: Value must be 1.
MSR: Range = 1-8.
Example: (config)# no interface multilink 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no interface serial
Use the no interface serial command denies access to the serial interface configuration commands.
To enter the serial interface configuration mode, see interface serial command on page 4-20.
Syntax:
(config)# no interface serial port
Field
Definition
port
Adit 3104: Value must be 1.
Adit 3200, Adit 3500: Range = 1-4.
MSR: Range = 1-8.
Example: (config)# no interface serial 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-42
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
no ip dhcp pool ethernet
Use the DHCP Pool no ip dhcp pool ethernet command to disable the DHCP server for the
interface defined. To enter the DHCP configuration mode, see ip dhcp pool ethernet command on
page 4-25.
Syntax:
(config)# no ip dhcp pool ethernet port
Field
Definition
port
Ethernet port number. 1 or 2.
Example: (config)# no ip dhcp pool ethernet 2
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no key
Use the no key command to disable a keyed feature. To enable a keyed feature, see the key command
on page 4-26.
Syntax:
(config)# no key key-code
Field
Definition
key-code
Enter the key code to disable the feature.
Example: (config)# no key q0B8yma2IsSL+1BarY0u
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no l2tpc
Use the no l2tpc command to disable the VPN L2TPC. To enter the VPN L2TPC configuration mode,
see the l2tpc command on page 4-26.
Syntax:
(config)# no l2tpc {l2tpc connection-id|address address}
Field
Definition
connection-id
Enter the name of a connection.
address
Enter a destination IP address.
Example: (config)# no l2tpc l2tpc 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-43
Global Configuration Mode
Global Configuration Commands
no local-server
Use the no local-server command to disable a local server. To enable a local server, see localserver command on page 4-27.
Syntax:
(config)# no local-server name
Field
Definition
name
Enter a name of the server to remove.
Example: (config)# no local-server BoulderServer
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no log sip
Use the no log sip command to stop SIP logging. To enable SIP logging, see log sip command on
page 4-30.
Syntax:
(config)# no log sip
Example: (config)# no log sip
Supported Platforms: Adit 3104, Adit 3500, MSR
no mail-server authentication
Use the no mail-server authentication command to disable the outgoing mail server
authentication. To enable the mail server, see mail-server command on page 4-33.
Syntax:
(config)# no mail-server authentication
Example: (config)# no mail-server authentication
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no nat-bypass
Use the no nat-bypass command to disable the NAT bypass feature. To enable NAT bypass, see
nat-bypass command on page 4-35.
Syntax:
(config)# no nat-bypass ip-address address mask mask [enable]
Field
Definition
address
Enter a NAT bypass IP address.
mask
Enter a subnet mask for the above address.
enable
Disable NAT bypass.
Example: (config)# no nat-bypass ip-address 192.168.1.50 mask
255.255.255.0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-44
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
no network-object
Use the no network-object command to remove network objects. To enable a network object, see
network-object command on page 4-35.
Syntax:
(config)# no network-object id object-id type {hostname
hostname|ip-address address|mac-address mac-address}
Field
Definition
object-id
Enter the numerical ID of the Network Object.
hostname
Enter the host name of the Network Object.
address
Enter the IP address of the Network Element.
mac-address
Enter the MAC address of the Network Element (xx:xx:xx:xx:xx:xx)
Example: (config)# no network-object id 1 type ip-address 192.168.1.200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no port-trigger-service
Use the no port-trigger-service command to remove a port-triggering entry. To configure port
triggering, see port-trigger service command on page 4-53.
Syntax:
(config)# no port-trigger-service name
Field
Definition
name
Enter service name.
Example: (config)# no port-trigger-service servicename2
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no pptpc
Use the no pptpc command to disable the VPN PPTP client. To enter the VPN PPTP Client
configuration mode, see the pptpc command on page 4-53.
Syntax:
(config)# no pptpc {pptpc connection-id|address address}
Field
Definition
connection-id
Enter the name of a connection.
address
Enter a destination IP address.
Example: (config)# no pptpc pptpc 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-45
Global Configuration Mode
Global Configuration Commands
no pptps
Use the no pptps command to disable the VPN PPTP server. To enter the VPN PPTPS configuration
mode, see the pptps command on page 4-53.
Syntax:
(config)# no pptps
Example: (config)# no pptps
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no radius-client
Use the no radius-client command disables the RADIUS configuration. To enter the RADIUS
configuration mode, see radius-client command on page 4-54.
Syntax:
(config)# no radius-client
Example: (config)# no radius-client
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no remote-admin icmp
Use the no remote-admin icmp command to remove access of ICMP echo requests (ping and
ICMP traceroute queries). To enable ICMP echo requests, see remote-admin icmp command on
page 4-54.
Syntax:
(config)# no remote-admin icmp
Example: (config)# no remote-admin icmp
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no remote-admin snmp
Use the no remote-admin snmp command to remove SNMP control and diagnostic requests. To
enable SNMP, see remote-admin snmp command on page 4-54.
Syntax:
(config)# no remote-admin snmp
Example: (config)# no remote-admin snmp
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-46
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
no remote-admin telnet
Use the no remote-admin telnet command to remove remote administration via Telnet. To enable
remote access via telnet, see remote-admin telnet command on page 4-55.
Syntax:
(config)# no remote-admin telnet {primary-port|
primary-secure-port|secondary-port
Field
Definition
primary-port
Primary Telnet port, default port 23
primary-secureport
Secure Telnet over SSL port, default port 992
secondary-port
Secondary Telnet port, default port 8023
Example: (config)# no remote-admin telnet primary-port
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no remote-admin udp-trace
Use the no remote-admin udp-trace command to remove remote access to UDP traceroute
queries. To enable remote access for UDP, see remote-admin udp-trace command on page 4-55.
Syntax:
(config)# no remote-admin udp-trace
Example: (config)# no remote-admin udp-trace
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-47
Global Configuration Mode
Global Configuration Commands
no remote-admin web
Use the no remote-admin web command to remove remote administration via
Web-management. To enable remote access via the web, see remote-admin web command on
page 4-56.
Syntax:
(config)# no remote-admin web {primary-port|
primary-secure-port|secondary-port|secondary-secure-port}
Field
Definition
primary-port
Primary HTTP port, default port 80
primary-secureport
Primary HTTPS port, default port 443
secondary-port
Secondary HTTP port, default port 8080
secondary-secureport
Secondary HTTPS port, default port 8443
Example: (config)# no remote-admin web primary-port
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no router ospf
Use the no router ospf command to disable Router OSPF. See Chapter 16, Configuration - OSPF
Mode for commands in this mode. To enter the OSPF configuration mode, see router ospf command
on page 4-56.
CAUTION! A NO ROUTER OSPF COMMAND WILL DELETE ALL OF THE OSPF CONFIGURATION.
Syntax:
(config)# no router ospf
Example: (config)# no router ospf
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-48
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
no security-log
Use the no security-log command to remove a security policy. To add a security policy, see
security-log command on page 4-58.
Syntax:
(config)# no security-log setting
Field
Definition
setting
Accepted Events accepted-in-connects
Blocked Events
Other Events
Log Buffer
Disable incoming connections logging.
accepted-out-connects
Disable outgoing connections logging.
block-conn-attempts
Disable block connection attempts logging.
blocked-fragments
Disable blocked fragments logging.
defrag-error
Disable defragmentation errors logging.
echo-chargen
Disable echo chargen logging.
icmp-flood
Disable ICMP flood logging.
icmp-multicast
Disable ICMP multicast logging.
icmp-redirect
Disable ICMP redirects logging.
icmp-replay
Disable ICMP replay logging.
multicast-broadcast
Disable multicast broadcasts logging.
pkt-illegal-opts
Disable packet illegal options logging.
spoofed-connection
Disable spoofed connection logging.
syn-flood
Disable syn flooding logging.
udp-flood
Disable UDP flooding logging.
winnuke
Disable winnuke configuration logging.
rem-admin-attempts
Disable remote admin attempts logging.
connection-states
Disable connection states logging.
prevent-log-overrun
Disable log overrun prevention logging.
Example: (config)# no security-log accepted-outgoing-connection
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-49
Global Configuration Mode
Global Configuration Commands
no service
Use the no service command to disable named services. To enable services, see service command
on page 4-59.
Syntax:
(config)# no service service-id
Field
Definition
service-id
Enter the service number to apply the rule to. Note: The Service ID
number is displayed with the show service command, on page 3-61
Example: (config)# no service-id 16777220
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no snmp-server
Use the no snmp-server command to disable SNMP on the system. To enable SNMP, see snmpserver command on page 4-60.
Syntax:
(config)# no snmp-server
Example: (config)# no snmp-server
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no snmp-server traps
Use the no snmp-server traps command to disable SNMP traps on the system. To enable SNMP
traps, see snmp-server traps enable command on page 4-61.
Syntax:
(config)# no snmp-server traps
Example: (config)# no snmp-server traps
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-50
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
no static-dns
Use the no static-dns command to remove DNS Static entries. To add a DNS static entry, see staticdns command on page 4-62.
Syntax:
(config)# no static-dns hostname hostname ip-address address
Field
Definition
hostname
Enter a DNS static host name of the server.
address
Enter the DNS static IP address.
Example: (config)# no static-dns hostname server1 ip-address
192.168.100.100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no time-range
Use the no time-range command to disable time range settings on the system. To set a time range,
see time-range command on page 4-62.
Syntax:
(config)# no time-range schedule-name
Field
Definition
schedule-name
Enter an existing schedule name to remove the time range restriction
to.
Example: (config)# no time-range SchedulerRule1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no username
Use the no username command to remove a user login from CLI. To add a username, see username
command on page 4-63.
Syntax:
(config)# no username name
Field
Definition
name
Enter an existing user name to remove.
Example: (config)# no username johndoe
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-51
Global Configuration Mode
Global Configuration Commands
no vlan
Use the no vlan command to clear all VLANs. To enter the VLAN configuration mode, see vlan
(global) command on page 4-63.
Syntax:
(config)# no vlan
Example: (config)# no vlan
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no voice-codec
Use the no voice-codec command to remove a voice codec. To set the voice codecs, see voice-codec
command on page 4-64.
Syntax:
(config)# no voice-codec {g711alaw|g711ulaw|g729}
Field
Definition
g711alaw
G.711, 64kbps, u-law
g711ulaw
G.711, 64kbps, A-law
g729
G.729, 8kbps
Example: (config)# no voice-codec g711alaw
Supported Platforms: Adit 3104, Adit 3500, MSR
no voice-port trunk
Use the no voice-port trunk command to disable the Voice Port Trunk. To enter the Voice Port
Trunk configuration mode, see voice-port trunk command on page 4-66.
Syntax:
(config)# no voice-port trunk port
Field
Definition
port
Trunk port number. Value must be 1.
Example: (config)# no voice-port trunk 1
Supported Platforms: Adit 3500, MSR
4-52
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
port-trigger service
Use the port-trigger service command to configure the port-triggering entries. To delete a port trigger
service, see no port-trigger-service command on page 4-45.
Syntax:
(config)# port-trigger service name enable
Field
Definition
name
Enter service name.
Example: (config)# port-trigger service service2 enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
pptpc
Use the pptpc command to allow access to the VPN PPTP Client configuration commands. See Chapter
17, Configuration - PPTPC Mode for commands in this mode. To delete an existing connection, see no
pptpc command on page 4-45
Syntax:
(config)# pptpc {pptpc connection-id|address address}
Field
Definition
connection-id
Enter the name of a connection. Range is 0-99.
address
Enter a destination IP address.
Example: (config)# pptpc pptpc 1
(config-pptpc-1)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
pptps
Use the pptps command to allow access to the VPN PPTP Server configuration commands. See
Chapter 18, Configuration - PPTPS Mode for commands in this mode.To delete an existing connection,
see no pptpc command on page 4-45.
Syntax:
(config)# pptps
Example: (config)# pptps
(config-pptps)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-53
Global Configuration Mode
Global Configuration Commands
radius-client
Use the radius-client command to allow access to the RADIUS configuration commands. See Chapter
19, Configuration - RADIUS Mode for commands in this mode. For the no counterpart of this command,
see no radius-client command on page 4-46.
Syntax:
(config)# radius-client
Example: (config)# radius-client
(config-radius)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
remote-admin
remote-admin icmp
Use the remote-admin icmp command to allow ICMP echo requests (pings). To deny ICMP echo
requests, see no remote-admin icmp command on page 4-46.
CAUTION!
Syntax:
ALLOWING REMOTE ADMINISTRATION IS A SECURITY RISK.
(config)# remote-admin icmp enable
Example: (config)# remote-admin icmp enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
remote-admin snmp
Use the remote-admin snmp command to allow SNMP control and diagnostic requests. To deny
SNMP, see no remote-admin snmp command on page 4-46.
CAUTION!
Syntax:
ALLOWING REMOTE ADMINISTRATION IS A SECURITY RISK.
(config)# remote-admin snmp enable
Example: (config)# remote-admin snmp enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-54
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
remote-admin telnet
Use the remote-admin telnet command to allow remote administration via Telnet. To deny telnet
remote access, see no remote-admin telnet command on page 4-47.
CAUTION!
Syntax:
ALLOWING REMOTE ADMINISTRATION IS A SECURITY RISK.
(config)# remote-admin telnet {primary-port|
primary-secure-port|secondary-port} {port port|enable}
Field
Definition
primary-port
Primary Telnet port, default port 23
primary-secureport
Secure Telnet over SSL port, default port 992
secondary-port
Secondary Telnet port, default port 8023
port
Enter a specific port to change from default ports listed above.
enable
Enable port on telnet remote admin.
Example: (config)# remote-admin telnet primary-port enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
remote-admin udp-trace
Use the remote-admin udp-trace command to allow UDP traceroute queries. To deny UDP
traceroute queries, see no remote-admin udp-trace command on page 4-47.
CAUTION!
Syntax:
ALLOWING REMOTE ADMINISTRATION IS A SECURITY RISK.
(config)# remote-admin udp-trace enable
Example: (config)# remote-admin udp-trace enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-55
Global Configuration Mode
Global Configuration Commands
remote-admin web
Use the remote-admin web command to allow remote administration via Web-management. To
deny Web remote access, see no remote-admin web command on page 4-48.
CAUTION!
Syntax:
ALLOWING REMOTE ADMINISTRATION IS A SECURITY RISK.
(config)# remote-admin web {primary-port|
secondary-port|primary-secure-port|secondary-secure-port}
[port] enable
Field
Definition
primary-port
Primary HTTP port, default port 80
secondary-port
Secondary HTTP port, default port 8080
primary-secureport
Primary HTTPS port, default port 443
secondary-secureport
Secondary HTTPS port, default port 8443
port
Enter a specific port to change from default ports listed above.
Example: (config)# remote-admin web primary-port enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
router ospf
Use the router ospf command to allow access to the Router OSPF global configuration commands. See
Chapter 16, Configuration - OSPF Mode for commands in this mode. For the no counterpart of this
command, see no router ospf command on page 4-48.
Syntax:
(config)# router ospf
Example: (config)# router ospf
(config-router-ospf)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-56
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
security-default
Use the security-default command to configure the security policy.
Syntax:
(config)# security-default {maximum|minimum|typical}
[block-ip-frag]
Field
Definition
The following security levels are described in detail.
Requests Originating in the
WAN
Requests Originating in the LAN
maximum
Blocked: No access to network
from Internet, except as
configured in the Local Servers,
DMZ host and Remote Access
screens.
Limited: Only commonly-used
services, such as Web-browsing and
e-mail, are permitted. These
services include Telnet, FTP,
HTTP, HTTPS, DNS, IMAP,
POP3, Ping and SNMP
minimum
Blocked: No access to network
from Internet, except as
configured in the local Servers,
DMZ host and Remote Access
screens.
Unrestricted: All services are
permitted, except as configured in
the Access Control screen.
typical (default)
Unrestricted: All services are
Unrestricted: Permits full
access from Internet to network; permitted, except as configured in
the Access Control screen.
all connection attempts
permitted.
block-ip-frag
Block IP Fragments
Checking this option will protect your network from a common type of
hacker attack that could make use of fragmented data packets to
sabotage your network. Note that VPN over IPSec and some UDPbased services make legitimate use of IP fragments. You will need to
allow IP fragments to pass into the home network in order to make use
of these selected services.
Example: (config)# security-default maximum
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-57
Global Configuration Mode
Global Configuration Commands
security-log
Use the security-log command to configure the security policy. To delete a security policy, see no
security-log command on page 4-49.
Syntax:
(config)# security-log setting enable
Field
Definition
Accepted Events
accepted-in-connections Sessions originated from the Internet that have been allowed by
the firewall.
accepted-outconnections
Sessions originated from the network that have been allowed by
the firewall.
Blocked Events
blocked-conn-attempts
Sessions that have been blocked by the firewall.
blocked-fragments
Detection of fragmented packets when Block IP Fragments is
enabled.
defrag-error
Detection of fragmented packets that cannot be properly
reassembled.
echo-chargen
Detection of the Echo or Chargen DOS attacks.
icmp-flood
Detection of an ICMP flood DOS attack.
icmp-multicast
Detection of multicast ICMP packets, such as a ping to a subnet
broadcast address.
icmp-redirect
Detection of improper ICMP redirect messages from the WAN.
icmp-replay
Detection of an ICMP Replay DOS attack.
multicast-broadcast
Detection of the Multicast or broadcast packets arriving at the
WAN interface.
pkt-illegal-opts
Detection of IP packets with disallowed IP options: lsrr, ssrr, rr,
timestamp, or error options.
spoofed-connection
Detection of IP address spoofing attacks.
syn-flood
Detection of the Syn Flood DOS attack.
udp-flood
Detection of a UDP Flood attack.
winnuke
Detection of the Winnuke DOS attack.
Other Events
connection-states
Session connection state detail.
rem-admin-attempts
Management sessions established.
Log Buffer
prevent-log-overrun
Stop logging firewall detail when the log is full. This prevents
loosing early log entries, but will drop the later log entries.
Example: (config)# security-log accepted-out-connection enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-58
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
service
Use the service command to create/modify User-Defined Services. To delete a service policy, see no
service command on page 4-50.
Syntax:
(config)# service id {service-id|new} name service-name
description text protocol {protocol-number|ah|esp|gre|icmp|tcp
|udp} [server-src-port|open-src-port]
Field
Definition
service-id
Enter a User-Defined Service number to modify. User-Defined Service ID numbers can be
displayed with the show config service command, on page 3-32
new
Will create a new User-Defined Service. Note: The system will assign an ID number. This number
will be the next available ID number in sequence (starts with 4, Note: 0-3 are configured by default).
Do not use the new option when using an Automated Provisioning System.
service-name
Enter service name, which can also be found on the show config service command, on page 3-32
description text
Enter a one word description.
protocol
Protocol to apply to this service.
protocol-number - this option allows the user to enter a protocol number to use protocols that are
not listed below.
ah - Authentication Header Protocol.
esp - Encapsulating Security Payload.
gre - Generic Routing Encapsulation.
icmp - Internet Control Message Protocol. Note: The range and a list of common settings are below.
type - Range 0-255
code - Range 0-255
Echo Reply................................................... icmp type 0 code 0
Network Unreachable .................................. icmp type 3 code 0
Host Unreachable......................................... icmp type 3 code 1
Protocol Unreachable................................... icmp type 3 code 2
Port Unreachable.......................................... icmp type 3 code 3
Destination Network Unknown ................... icmp type 3 code 6
Destination Host Unknown.......................... icmp type 3 code 7
Redirect for Network ................................... icmp type 5 code 0
Redirect for Host.......................................... icmp type 5 code 1
Echo Request ............................................... icmp type 8 code 0
tcp - Transmission Control Protocol. See source and destination port settings below.
udp - User Datagram Protocol. See source and destination port settings below.
open-src-port
Defines the open source/destination port. Syntax:
open-src-port {port|port-port|any} open-dst-port {port|port-port|
any}
open-src-port
port - Enter the open source port to apply the service to.
port-port - Enter a range of ports to apply the service to.
any - Apply to any port.
open-dst-port
port - Enter the destination source port to apply the service to.
port-port - Enter a range of ports to apply the service to.
any - Apply to any port.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-59
Global Configuration Mode
Global Configuration Commands
server-src-port
Defines the server source/destination port. Syntax:
server-src-port {port|port-port|any} server-dst-port {port|portport|any}
server-src-port
port - Enter the server source port to apply the service to.
port-port - Enter a range of ports to apply the service to.
any - Apply to any port.
server-dst-port
port - Enter the server destination port to apply the service to.
port-port - Enter a range of ports to apply the service to.
any - Apply to any port.
Example: (config)# service id 5 name test description desc1 protocol gre
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
snmp-server
The following are the commands to set the SNMP server configuration. To disable SNMP, see no snmpserver command on page 4-50.
snmp-server community
Use the snmp-server community command to set the SNMP community name.
Syntax:
(config)# snmp-server community community-name {ro|rw}
Field
Definition
community-name
Enter the SNMP Community Name.
ro
Read only - Set the community name to read only permission.
rw
Read write - Set the community name to read and write permission.
Example: (config)# snmp-server community communitytestname ro
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
snmp-server enable
Use the snmp-server enable command to enable SNMP on the system.
Syntax:
(config)# snmp-server enable
Example: (config)# snmp-server enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-60
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
snmp-server host
Use the snmp-server host command to set a SNMP host.
Syntax:
(config)# snmp-server host address {community
community-name|version {1|2c}
Field
Definition
address
Enter an destination IP address.
community-name
Enter the SNMP community name.
version
1 - SNMPv1
2c - SNMPv2c
Example: (config)# snmp-server host 192.168.1.1 version 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
snmp-server traps enable
Use the snmp-server traps enable command to enable SNMP traps on the system. To delete a
SNMP server trap, see no snmp-server traps command on page 4-50.
Syntax:
(config)# snmp-server traps enable
Example: (config)# snmp-server traps enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
snmp-server trusted-ip
Use the snmp-server trusted-ip command to set a SNMP trusted peer (The IP address, or subnet
address that identifies which remote management stations are allowed to perform SNMP
operations).
Syntax:
(config)# snmp-server trusted-ip {address|any}
[trusted-mask mask]
Field
Definition
address
Enter an IP address of a trusted peer.
any
Allow any IP address trusted peer access.
trusted-mask mask
This is an optional parameter, enter the subnet mask of the trusted peer
IP address.
Example: (config)# snmp-server trusted ip any
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-61
Global Configuration Mode
Global Configuration Commands
static-dns
Use the static-dns command to configure the DNS Static entries. To delete static DNS entries, see no
static-dns command on page 4-51.
Syntax:
(config)# static-dns hostname hostname ip-address address
Field
Definition
hostname
Enter a DNS static host name of the server.
address
Enter the DNS static IP address.
Example: (config)# static-dns hostname server1 ip-address 192.168.100.100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
time-range
Use the time-range command to define availability of the Ethernet port. To delete a time range, see no
time-range command on page 4-51.
Syntax:
(config)# time-range id schedule-id name schedule-name
{active|inactive} time-segment time-segment-id
{mon|tue|wed|thu|fri|sat|sun} time-range hh:mm-hh:mm
Field
Definition
schedule-id
Enter a schedule ID for the scheduler rule.
schedule-name
Enter a name for the scheduler rule.
active
Sets this time range to be active during the set time.
inactive
Sets this time range to be inactive during the set time.
time-segment-id
Enter time-range ID to apply. Range 0 - 9999
mon|tue|wed|thu|fri Select the days of the week the interface for the rule.
|sat|sun
hh:mm-hh:mm
Set the range of time, start time-end time.
hh = hours, range 00 - 23
mm = minutes, range 00 - 59
Example: (config)# time-range id 1 name test1 active time-segment 2 mon
08:00-18:00
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
4-62
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
username
Use the username command to create/modify a user profile for CLI. To delete a username, see no
username command on page 4-51.
Syntax:
(config)# username name password password {admin|monitor
|operator}
Field
Definition
name
Enter a User name, with a maximum of 15 characters.
password
Password for the user, with a maximum of 15 characters. This is an
optional parameter. Default is "password".
admin
Read/write privileges, including user access management.
monitor
Read only privileges. Default is monitor.
operator
Read/write privileges, excluding user access management.
Example: (config)# username johndoe password mypassword operator
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
vlan (global)
Use the vlan command to allow access to the global VLAN configuration commands. See Chapter 20,
Configuration - VLAN Mode for commands in this mode. To clear VLANs, see the no vlan command
on page 4-52.
Syntax:
(config)# vlan
Example: (config)# vlan
(config-vlan)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-63
Global Configuration Mode
Global Configuration Commands
vlan (vlan-id)
Use the vlan command to allow access to the VLAN port configuration commands. See Chapter 21,
Configuration - VLAN Port Mode for commands in this mode.
Syntax:
(config)# vlan v-id
Field
Definition
v-id
VLAN identifier. Range 2-4096.
Example: (config)# vlan 100
(config-vlan-100)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
voice-codec
Use the voice-codec command to select which codecs are to be enabled and allows the user to set the
Packetization Time for that codec. To disable a codec, see no voice-codec command on page 4-52.
Syntax:
(config)# voice-codec {g711alaw|g711ulaw|g729}
ptime {10|20|30|40|50|60|70|80}
Field
Definition
g711alaw
G.711, 64kbps, A-law
g711ulaw
G.711, 64kbps, μ-law
g729
G.729, 8kbps
ptime
Set the Packetization Time for the codec. Default for all is 20.
Packetization Time for each codec is as follows:
G.711A-Law = 10, 20, 30, 40, 50 or 60
G.711μ-Law = 10, 20, 30, 40, 50 or 60
G.729 = 10, 20, 30, 40, 50, 60, 70 or 80
Example: (config)# voice-codec g711alaw ptime 30
Supported Platforms: Adit 3104, Adit 3500, MSR
4-64
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Global Configuration Mode
Global Configuration Commands
voice-port (global)
Use the voice-port fxs command to allow access to the Voice Port (global) configuration commands.
See Chapter 22, Configuration - Voice Port Mode for commands in this mode.
Syntax:
(config)# voice-port
Example: (config)# voice-port
(config-vport)#
Supported Platforms: Adit 3104, Adit 3500, MSR
voice-port fxs
Use the voice-port fxs command to allow access to the Voice Port FXS configuration commands. See
Chapter 23, Configuration - Voice Port FXS Mode for commands in this mode.
Syntax:
(config)# voice-port fxs port
Field
Definition
port
FXS voice port number.
Adit 3104: Range = 1-8.
Adit 3500: Range = 1-4.
MSR: Range = 1-48.
Example: (config)# voice-port fxs 1
(config-vport-fxs-1)#
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
4-65
Global Configuration Mode
Global Configuration Commands
voice-port trunk
Use the voice-port trunk command to allow access to the Voice Port Trunk configuration commands.
See Chapter 24, Configuration - Voice Port Trunk Mode for commands in this mode. To remove access
to a Voice Port Trunk, see no voice-port trunk command on page 4-52.
Syntax:
(config)# voice-port trunk port
Field
Definition
port
FXS voice port trunk number. Value must be 1.
Example: (config)# voice-port trunk 1
(config-vport-trk-1)#
Supported Platforms: Adit 3500, MSR
voice-service sip
Use the voice-service sip command to allow access to the Voice Service SIP configuration commands.
See Chapter 25, Configuration - Voice Service SIP Mode for commands in this mode.
Syntax:
(config)# voice-service sip
Example: (config)# voice-service sip
(config-serv-sip)#
Supported Platforms: Adit 3104, Adit 3500, MSR
4-66
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
5
Configuration - LCC Controller Mode
The LCC (Link Cross-Connect) Controller Configuration commands allow the user to configure the
Link Cross-Connect parameters for the MSR card.
Note: The LCC Controller Configuration mode is supported by the MSR card only. For Controller
Configuration commands for the Adit 3000 series, see Chapter 6, Configuration - T1 Controller Mode.
This sub-group is entered with the (config)# controller lcc command from the Configuration mode.
The LCC Controller commands are represented by the (config-cont-lcc-{n})# prompt.
LCC Controller Commands
• description
• do
• end
• exit
• history
• no command
• shutdown
Configuration - LCC Controller Mode
description
Use the Controller LCC description command to enter a description for the LCC.
Syntax:
(config-cont-lcc-{n})# description text
Field
Definition
text
Enter a description for the LCC.
Example: (config-cont-lcc-1)# description LCC#1
Supported Platforms: MSR
5-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - LCC Controller Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
5-3
Configuration - LCC Controller Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-cont-lcc-{n})# end
Example: (config-cont-lcc-1)# end
#
Supported Platforms: MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-cont-lcc-{n})# exit
Example: (config-cont-lcc-1)# exit
(config)#
Supported Platforms: MSR
5-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - LCC Controller Mode
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-cont-lcc-{n})# history
Example: (config-cont-lcc-1)# history
history
description Test-LCC
no shutdown
history
Supported Platforms: MSR
no command
no shutdown
Use the Controller LCC no shutdown command to set the LCC up (in-service). To set the LCC
down (Out-of-Service), see the shutdown command on page 5-6.
Syntax:
(config-cont-lcc-{n})# no shutdown
Example: (config-cont-lcc-1)# no shutdown
Supported Platforms: MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
5-5
Configuration - LCC Controller Mode
shutdown
Use the Controller LCC shutdown command to set the LCC interface down (out-of-service). To set the
LCC up (in-service), see the no shutdown command on page 5-5.
Syntax:
(config-cont-lcc-{n})# shutdown
Example: (config-cont-lcc-1)# shutdown
Supported Platforms: MSR
5-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
6
Configuration - T1 Controller Mode
The T1 Controller Configuration commands allow the user to configure the T1 parameters on the Adit
3000 series.
Note: The T1 Controller Configuration mode is supported by the Adit 3000 series only. For Controller
Configuration commands for the MSR card, see Chapter 5, Configuration - LCC Controller Mode.
This sub-group is entered with the (config)# controller t1 command from the Configuration mode.
The T1 Controller commands are represented by the (config-cont-t1-{n})# prompt.
T1 Controller Commands
• description
• lbo
• do
• linecode
• ds0-group
• loopback
• end
• loopdetect
• exit
• no commands
• fdl
• pri-group
• framing
• shutdown
• history
• tdm-group
• idle-pattern
• threshold
Configuration - T1 Controller Mode
description
Use the Controller T1 description command to set the circuit ID of the T1.
Syntax:
(config-cont-t1-{n})# description text
Field
Definition
text
Enter a description for the Controller T1.
Example: (config-cont-t1-1)# description T1#1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
6-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - T1 Controller Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
6-3
Configuration - T1 Controller Mode
ds0-group
Use the Controller T1 ds0-group command to create a group of T1s. To delete a DS0 group, see
no ds0-group command on page 6-9.
Syntax:
(config-cont-t1-{n})# ds0-group timeslots range
Field
Definition
range
DS0 timeslot range, in the format n-n (1-4). Range is 1 - 24.
Example: (config-cont-t1-1)# ds0-group timeslots 1-4
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-cont-t1-{n})# end
Example: (config-cont-t1-1)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-cont-t1-{n})# exit
Example: (config-cont-t1-1)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
6-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - T1 Controller Mode
fdl
Use the Controller T1 fdl command to set line Facilities Data Link (FDL) capabilities the T1 interface.
Syntax:
(config-cont-t1-{n})# fdl {none|t1.403}
Field
Definition
none
Disable FDL output messages. Default.
t1.403
Enable T1.403 FDL performance messages.
Example: (config-cont-t1-1)# fdl none
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
framing
Use the Controller T1 framing command to set the framing option for the designated T1.
Syntax:
(config-cont-t1-{n})# framing {d4|esf}
Field
Definition
d4
D4 Superframe (SF)
esf
Extended Superframe. Default.
Example: (config-cont-t1-1)# framing d4
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
6-5
Configuration - T1 Controller Mode
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-cont-t1-{n})# history
Example: (config-cont-t1-1)# history
history
framing d4
threshold daily lcv
threshold d
threshold daily pcv
threshold daily bes
threshold daily css
threshold daily uas 1000
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
idle-pattern
Use the Controller T1 idle-pattern command to set the idle pattern on the designated T1.
Syntax:
(config-cont-t1-{n})# idle-pattern number
Field
Definition
number
A hexadecimal number with a range from 0x00 to 0xff. This number
must be preceeded by 0x. Default 0x7f.
Example: (config-cont-t1-1)# idle-pattern 0x7f
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
6-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - T1 Controller Mode
lbo
lbo long
Use the Controller T1 lbo long command to set Line Build Out on the T1.
Syntax:
(config-cont-t1-{n})# lbo long {-7.5db|-15db|-22.5db}
Field
Definition
-7.5db
CSU attenuation for LBO of 7.5dB
-15db
CSU attenuation for LBO of 15dB
-22.5db
CSU attenuation for LBO of 22.5dB
Example: (config-cont-t1-1)# lbo long -15db
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
lbo short
Use the Controller T1 lbo short command to set Line Build Out on the T1.
Syntax:
(config-cont-t1-{n})# lbo short {133|266|399|533|655}
Field
Definition
133
DSX-1 equalization for 0-133 ft. Default.
266
DSX-1 equalization for 133-266 ft.
399
DSX-1 equalization for 266-399 ft.
533
DSX-1 equalization for 399-533 ft.
655
DSX-1 equalization for 533-655 ft.
Example: (config-cont-t1-1)# lbo short 266
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
6-7
Configuration - T1 Controller Mode
linecode
Use the Controller T1 linecode command to set the line coding for the designated T1.
Syntax:
(config-cont-t1-{n})# linecode {ami|b8zs}
Field
Definition
ami
Alternate Mark Inversion line coding (AMI).
b8zs
Binary 8 Zero Substitution line coding (B8ZS). Default.
Example: (config-cont-t1-1)# linecode ami
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
loopback
Use the Controller T1 loopback command enables a loopback on the T1.
Syntax:
(config-cont-t1-{n})# loopback {line|none|payload}
Field
Definition
line
Line loopback enabled.
none
Loopback disabled. Default.
payload
Payload loopback enabled.
Example: (config-cont-t1-1)# loopback line
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
6-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - T1 Controller Mode
loopdetect
Use the Controller T1 loopdetect command to enable the detection of CSU or NIU loop code.
Syntax:
(config-cont-t1-{n})# loopdetect {csu|niu|none}
Field
Definition
csu
Enable detection of CSU loop codes (10000 for loop up, 100 for loop
down)
niu
Enable detection of NIU loop codes
none
Disable detection. Default.
Example: (config-cont-t1-1)# loopdetect csu
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
no commands
no ds0-group
Use the Controller T1 no ds0-group command to ungroup DS0 timeslots. To group DS0s, see
ds0-group command on page 6-4.
Syntax:
(config-cont-t1-{n})# no ds0-group
Example: (config-cont-t1-1)# no ds0-group
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
no pri-group
Use the Controller T1 no pri-group command to ungroup PRI timeslots. To group PRI timeslots,
see pri-group command on page 6-10.
Syntax:
(config-cont-t1-{n})# no pri-group timeslots range
Field
Definition
range
PRI timeslot range, in the format n-n (1-4). Range is 1 - 23.
Example: (config-cont-t1-1)# no pri-group timeslots 1-4
Supported Platforms: Adit 3104, Adit 3500
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
6-9
Configuration - T1 Controller Mode
no shutdown
Use the Controller T1 no shutdown command to set the T1 up (In-Service). To set the T1 down
(Out-of-Service), see shutdown command on page 6-11.
Syntax:
(config-cont-t1-{n})# no shutdown
Example: (config-cont-t1-1)# no shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
no tdm-group
Use the Controller T1 no tdm-group command to ungroup TDM timeslots. To group TDM
timeslots, see tdm-group command on page 6-11.
Syntax:
(config-cont-t1-{n})# no tdm-group timeslots range
Field
Definition
range
TDM timeslot range, in the format n-n (1-4). Range is 1 - 24.
Example: (config-cont-t1-1)# no tdm-group timeslots 1-4 dir
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
pri-group
Use the Controller T1 pri-group command to group PRI timeslots. To delete a PRI group, see
no pri-group command on page 6-9.
Syntax:
(config-cont-t1-{n})# pri-group timeslots range dir
{in|in-out|out}
Field
Definition
range
PRI timeslot range, in the format n-n (1-4). Range is 1 - 23.
in
Defines the direction as incoming only.
in-out
Defines the direction as both incoming and outgoing.
out
Defines the direction as outgoing only.
Example: (config-cont-t1-1)# pri-group timeslots 1-4
Supported Platforms: Adit 3104, Adit 3500
6-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - T1 Controller Mode
shutdown
Use the Controller T1 shutdown command to set the T1 interface down (out-of-service). To set the T1
up (in-service) see no shutdown command on page 6-10.
Syntax:
(config-cont-t1-{n})# shutdown
Example: (config-cont-t1-1)# shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
tdm-group
Use the Controller T1 tdm-group command to create a group and define its direction. To delete a TDM
group, see no tdm-group command on page 6-10.
Syntax:
(config-cont-t1-{n})# tdm-group timeslots range dir
{in|in-out|out}
Field
Definition
range
TDM timeslot range, in the format n-n (1-4). Range is 1 - 24.
in
Defines the direction as incoming only.
in-out
Defines the direction as both incoming and outgoing.
out
Defines the direction as outgoing only.
Example: (config-cont-t1-1)# tdm-group timeslots 1-4 dir in-out
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
6-11
Configuration - T1 Controller Mode
threshold
Use the Controller T1 threshold command to define the interval and threshold levels for this T1.
Syntax:
(config-cont-t1-{n})# threshold {daily|min15}
{bes|css|dm|es|lcv|les|pcv|sefs|ses|uas} {value}
Threshold Settings
Minute 15
Daily
BES - Bursty Errored Seconds Default is 0.
Defect Threshold
Range is 0 - 900
Default is 0.
Range is 0 - 86400
CSS - Controller Slip Seconds
Defect Threshold
Default is 0.
Range is 0 - 900
Default is 0.
Range is 0 - 86400
DM - Degraded Minutes
Threshold
Default is 0.
Range is 0 - 15
Default is 0.
Range is 0 - 1440
ES - Errored Seconds Defect
Threshold
Default is 0.
Range is 0 - 900
Default is 0.
Range is 0 - 86400
LCV - Line Code Violations
Defect Threshold
Default is 0.
Default is 0.
Range is 0 - 1389600 Range is 0 - 133401600
LES - Line Errored Seconds
Defect Threshold
Default is 0.
Range is 0 - 900
PCV - Path Code Violation
Defect Threshold
Default is 0.
Default is 0.
Range is 0 - 1389600 Range is 0 - 133401600
SEFS - Severely Errored
Frame Seconds Threshold
Default is 0.
Range is 0 - 900
Default is 0.
Range is 0 - 86400
SES - Severely Errored
Seconds Threshold
Default is 0.
Range is 0 - 900
Default is 0.
Range is 0 - 86400
UAS - Unavailable Seconds
Defect Threshold
Default is 0.
Range is 0 - 900
Default is 0.
Range is 0 - 86400
Default is 0.
Range is 0 - 86400
Example: (config-cont-t1-1)# threshold 15min les 1200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
6-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
7
Configuration - DHCP Pool Ethernet Mode
The DHCP Pool Configuration commands allow the user to configure the DHCP parameters for each
interface.
This sub-group is entered with the (config)# ip dhcp pool ethernet command from the Configuration
mode.
The DHCP Pool commands are represented by the (config-dhcp-eth-{n})# prompt.
DHCP Pool Commands
•
•
•
•
•
•
•
•
•
•
•
•
•
do
end
end-address
exit
history
lease
no commands
option
relay
start-address
static-lease
subnet-mask
wins server
Configuration - DHCP Pool Ethernet Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
7-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - DHCP Pool Ethernet Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-dhcp-eth-{n})# end
Example: (config-dhcp-eth-1)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
end-address
Use the DHCP end-address command to define the DHCP end address. This command works with the
start-address (start IP address) to define the number of IP addresses in the DHCP pool. This also limits
the number of hosts that may be connected to the network in this subnet. End-address defines the last
IP address that may be assigned in this subnet.
Syntax:
(config-dhcp-eth-{n})# end-address address
Field
Definition
address
The ending address of the client address pool, in the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255
Example: (config-dhcp-eth-1)# end-address 192.168.1.255
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-dhcp-eth-{n})# exit
Example: (config-dhcp-eth-1)# exit
Example: (config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
7-3
Configuration - DHCP Pool Ethernet Mode
history
Use the history command to display commands that have been entered in this session.
NOTE: This command can be entered in any configuration mode.
Syntax:
(config-dhcp-eth-{n})# history
Example: (config-dhcp-eth-1)# history
end-address 192.168.1.250
lease 900
relay 192.168.1.120
start-address 192.168.1.1
subnet-mask 255.255.255.0
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
lease
Use the DHCP lease command to define the DHCP lease time, in minutes. This defines the lease
duration, or the length of time for which the IP address can be used before a lease renewal is required,
or if the address is no longer in use, it is automatically returned to the pool for reallocation.
Syntax:
(config-dhcp-eth-{n})# lease time
Field
Definition
time
Enter the DHCP lease time. Range is 1 - 71582788 minutes, with a
default of 60.
Example: (config-dhcp-eth-1)# lease 120
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
7-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - DHCP Pool Ethernet Mode
no commands
no option
Use the DHCP Pool no option command to delete a DHCP option. To add a DHCP pool, see
option command on page 7-6.
Syntax:
(config-dhcp-eth-{n})# no option {66|67}
Field
Definition
66
Remove/Disable option 66 (TFTP server name).
67
Remove/Disable option 67 (Boot file name).
Example: (config-dhcp-eth-1)# no option 66
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no relay
Use the DHCP Pool no relay command to disable DHCP relay. To enable relay, see
relay command on page 7-6.
Syntax:
(config-dhcp-eth-{n})# no relay
Example: (config-dhcp-eth-1)# no relay
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no static-lease
Use the DHCP Pool no static-lease command to remove a static DHCP lease. To add a static lease,
see static-lease command on page 7-7.
Syntax:
(config-dhcp-eth-{n})# no static-lease ip-address address
Field
Definition
address
Enter the IP address of the static lease to remove.
Example: (config-dhcp-eth-1)# no static-lease ip-address 10.10.2.100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
7-5
Configuration - DHCP Pool Ethernet Mode
option
Use the option command to configure DHCP options per RFC 2132. To delete an option, see no option
command on page 7-5.
Syntax:
(config-dhcp-eth-{n})# option {66 {enable|value
{address|hostname}|67 {enable|value filename}
Field
Definition
66
66 - Send the TFTP server name.
address - Enter the IP address of the TFTP server.
hostname - Enter the host name of the TFTP server.
67
67 - Send the Boot file name.
filename - Enter the boot file name.
enable
To enable the DHCP option.
Example: (config-dhcp-eth-1)# option value 66 10.10.5.100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
relay
Use the DHCP Pool relay command to configure DHCP relay. The DHCP relay is responsible for
forwarding the requests and responses negotiating between the DHCP clients and the server. To delete
DHCP relay, see no relay command on page 7-5.
Syntax:
(config-dhcp-eth-{n})# relay address1 [address2] [address3] ...
Field
Definition
address
The DHCP relay IP address, in the form of xxx.xxx.xxx.xxx, where
xxx is between 0-255
address1, address 2, Optional address parameter, to enter additional DHCP relay IP
...
addresses, in the form of xxx.xxx.xxx.xxx, where xxx is between
0-255
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
7-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - DHCP Pool Ethernet Mode
start-address
Use the DHCP Pool start-address command to define the DHCP start IP address. This command works
with the end-address (end IP address) to define the number of IP addresses in the DHCP pool. This also
limits the number of hosts that may be connected to the network in this subnet. Start defines the first IP
address that may be assigned in this subnet.
Syntax:
(config-dhcp-eth-{n})# start-address address
Field
Definition
address
The starting address of the client address pool, in the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255
Example: (config-dhcp-eth-1)# start-address 192.168.1.1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
static-lease
Use the DHCP Pool static-lease command to add a static DHCP lease. To delete a lease, see no staticlease command on page 7-5.
Syntax:
(config-dhcp-eth-{n})# static-lease ip-address address hostname
hostname
Field
Definition
address
The starting address of the client address pool, in the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255
hostname
Set the static lease host name
Example: (config-dhcp-eth-1)# static-lease ip-address 192.168.1.100
hostname www.turinnetworks.com
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
7-7
Configuration - DHCP Pool Ethernet Mode
subnet-mask
Use the DHCP Pool subnet-mask command to define the subnet mask for the DHCP pool.
Syntax:
(config-dhcp-eth-{n})# subnet-mask mask
Field
Definition
mask
Enter the DHCP pool subnet mask, using the form xxx.xxx.xxx.xxx,
where xxx is a number from 0 to 255. This is an optional setting.
Example: (config-dhcp-eth-1)# subnet-mask 255.255.255.0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
wins server
Use the DHCP Pool wins sever command to set the WINS server IP address of the client address pool.
Syntax:
(config-dhcp-eth-{n})# wins server address
Field
Definition
address
The WINS server IP address of the client address pool, in the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255
Example: (config-dhcp-eth-1)# wins server 192.168.3.1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
7-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
8
Configuration - Dial Peer FXS Mode
The Dial Peer FXS Configuration commands allow the user to configure the Dial Peer FXS parameters.
Enter this sub-group with the (config)# dial-peer voice pots fxs port command from the Configuration
mode.
The Dial Peer FXS commands are represented by the (config-dpeer-fxs)# prompt.
Dial Peer FXS Commands
•
•
•
•
•
•
•
•
•
•
•
•
•
•
block-out-caller-id
call-wait-caller-id
call-waiting
calling-party-disc
codec preference
destination-pattern
do
end
exit
fax-protocol
history
modem-protocol
no commands
sip-authentication
Configuration - Dial Peer FXS Mode
block-out-caller-id
Use the Dial Peer block-out-caller-id command to enable the blocking of outgoing Caller ID. To
disable blocking, see no block-out-caller-id command on page 8-8.
Syntax:
(config-dpeer-fxs)# block-out-caller-id enable
Example: (config-dpeer-fxs)# block-out-caller-id enable
Supported Platforms: Adit 3104, Adit 3500, MSR
call-wait-caller-id
Use the Dial Peer call-wait-caller-id command to enable Call Waiting and Caller ID. To disable these
calling features, see no call-wait-caller-id command on page 8-8.
Syntax:
(config-dpeer-fxs)# call-wait-caller-id enable
Example: (config-dpeer-fxs)# call-wait-caller-id enable
Supported Platforms: Adit 3104, Adit 3500, MSR
call-waiting
Use the Dial Peer call-waiting command to enable Call Waiting. To disable Call Waiting, see no callwaiting command on page 8-8.
Syntax:
(config-dpeer-fxs)# call-waiting enable
Example: (config-dpeer-fxs)# call-waiting enable
Supported Platforms: Adit 3104, Adit 3500, MSR
calling-party-disc
Use the Dial Peer calling-party-disc command to enable Calling Party Disconnect. To disable this
feature, see no calling-party-disc command on page 8-8.
Syntax:
(config-dpeer-fxs)# calling-party-disc enable
Example: (config-dpeer-fxs)# calling-party-disc enable
Supported Platforms: Adit 3104, Adit 3500, MSR
8-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Dial Peer FXS Mode
codec preference
Use the Dial Peer codec preference command to set the codec preferences used to establish the codec
list offered during media negotiation. To delete a codec, see no codec preference command on page 8-9.
Syntax:
(config-dpeer-fxs)# codec preference {1|2|3} {g711alaw|
g711ulaw|g729}
Field
Definition
1|2|3
Enter the preference number. #1 being the first preference.
g711alaw
Set the codec preference to G.711 A-law.
g711ulaw
Set the codec preference to G.711 U-law.
g729
Set the codec preference to G.729.
Note: This codec is not supported by the Adit 3500 or MSR for FXS.
Example: (config-dpeer-fxs)# codec preference 1 g711alaw
Supported Platforms: Adit 3104, Adit 3500, MSR
destination-pattern
Use the Dial Peer destination-pattern command to define the full telephone number to be used for a
dial peer.
Syntax:
(config-dpeer-fxs)# destination-pattern number
Field
Definition
number
Enter the phone number to be used for a dial peer.
Example: (config-dpeer-fxs)# destination-pattern 5551212
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
8-3
Configuration - Dial Peer FXS Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
8-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Dial Peer FXS Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file.
Syntax:
(config-dpeer-fxs}# end
Example: (config-dpeer-fxs)# end
#
Supported Platforms: Adit 3104, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-dpeer-fxs} {n})# exit
Example: (config-dpeer-fxs)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
8-5
Configuration - Dial Peer FXS Mode
fax-protocol
Use the Dial Peer fax-protocol command to configure the fax protocol.
Syntax:
(config-dpeer-fxs)# fax-protocol {none|pass-through|t38}
Field
Definition
none
A Fax call would be treated as a normal voice call. Default.
pass-through
Will cause the line to transmit in G.711 mode, with echo cancellation
and silence suppression disabled, on detection of Fax tone.
t38
Upon detection of a Fax tone on the port, will cause the gateway to
negotiate a T.38 session with its peer and if successful, will enter T.38
Fax-relay mode. Will dynamically consume a T.38 token for the
session.
Note: For the MSR, T.38 will be supported in a future release.
Example: (config-dpeer-fxs)# fax-protocol none
Supported Platforms: Adit 3104, Adit 3500, MSR
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-dpeer-fxs)# history
Example: (config-dpeer-fxs)# history
history
block-out-caller-id enable
call-wait-caller-id enable
call-waiting enable
calling-party-disc enable
codec preference 1 g729
history
Supported Platforms: Adit 3104, Adit 3500, MSR
8-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Dial Peer FXS Mode
modem-protocol
Use the Dial Peer modem-protocol command to configure the modem protocol.
Syntax:
(config-dpeer-fxs)# modem-protocol {none|pass-through}
Field
Definition
none
A Modem call would be treated as a normal voice call. Default.
pass-through
Will cause the line to transmit in G.711 mode, with echo cancellation
and silence suppression disabled, on detection of Modem tone.
Example: (config-dpeer-fxs)# modem-protocol pass-though
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
8-7
Configuration - Dial Peer FXS Mode
no commands
no block-out-caller-id
Use the Dial Peer no block-out-caller-id command to disable the Caller ID blocking. To enable
blocking, see block-out-caller-id command on page 8-2.
Syntax:
(config-dpeer-fxs)# no block-out-caller-id
Example: (config-dpeer-fxs)# no block-out-caller-id
Supported Platforms: Adit 3104, Adit 3500, MSR
no call-wait-caller-id
Use the Dial Peer no call-wait-caller-id command to disable Call Waiting Caller ID. To enable
these calling features, see call-wait-caller-id command on page 8-2.
Syntax:
(config-dpeer-fxs)# no call-wait-caller-id
Example: (config-dpeer-fxs)# no call-wait-caller-id
Supported Platforms: Adit 3104, Adit 3500, MSR
no call-waiting
Use the Dial Peer no call-waiting command to disable Call Waiting. To enable Call Waiting, see
call-waiting command on page 8-2.
Syntax:
(config-dpeer-fxs)# no call-waiting
Example: (config-dpeer-fxs)# no call-waiting
Supported Platforms: Adit 3104, Adit 3500, MSR
no calling-party-disc
Use the Dial Peer no calling-party-disc command to disable Calling Party Disconnect. To enable
this feature, see calling-party-disc command on page 8-2.
Syntax:
(config-dpeer-fxs)# no calling-party-disc
Example: (config-dpeer-fxs)# no calling-party-disc
Supported Platforms: Adit 3104, Adit 3500, MSR
8-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Dial Peer FXS Mode
no codec preference
Use the Dial Peer no codec preference command to remove a codec preference. To set the codec
preferences, see codec preference command on page 8-3.
Syntax:
(config-dpeer-fxs)# no codec preference {1|2|3}
Field
Definition
1|2|3
Remove a specific codec preference. Range 1 - 3
Example: (config-dpeer-fxs)# no codec preference 1
Supported Platforms: Adit 3104, Adit 3500, MSR
no sip-authentication
Use the Dial Peer no sip-authentication command to disable SIP authentication. To enable SIP
authentication, see sip-authentication command on page 8-10.
Syntax:
(config-dpeer-fxs)# no sip-authentication
Example: (config-dpeer-fxs)# no sip-authentication
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
8-9
Configuration - Dial Peer FXS Mode
sip-authentication
Note: To disable this SIP authentication, see the no sip-authentication command on page 8-9.
sip-authentication enable
Use the Dial Peer sip-authentication enable command to enable SIP.
Syntax:
(config-dpeer-fxs)# sip-authentication enable
Example: (config-dpeer-fxs)# sip-authentication enable
Supported Platforms: Adit 3104, Adit 3500, MSR
sip-authentication password
Use the Dial Peer sip-authentication password command to set the SIP password.
Syntax:
(config-dpeer-fxs)# sip-authentication password password
Field
Definition
password
The password to be used when responding to authentication requests.
Example: (config-dpeer-fxs)# sip-authentication password
test-password
Supported Platforms: Adit 3104, Adit 3500, MSR
sip-authentication username
Use the Dial Peer sip-authentication username command to set the SIP ID.
Syntax:
(config-dpeer-fxs)# sip-authentication username username
Field
Definition
username
The User ID to be used when responding to authentication requests.
Default is the User ID of the line.
Example: (config-dpeer-fxs)# sip-authentication username
test-user-1
Supported Platforms: Adit 3104, Adit 3500, MSR
8-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
9
Configuration - Dial Peer Trunk Mode
The Dial Peer Trunk Configuration commands allow the user to configure the Dial Peer Trunk
parameters.
Enter this sub-group with the (config)# dial-peer voice pots trunk trunk dest-port command from the
Configuration mode.
The Dial Peer Trunk commands are represented by the (config-dpeer-trk)# prompt.
Note: The Dial Peer Trunk option is not supported on the Adit 3104.
Dial Peer Trunk Commands
•
•
•
•
•
•
•
•
•
•
•
•
codec preference
destination-pattern
do
end
exit
fax-protocol
history
modem-protocol
no commands
prefix
sip-authentication
strip-digits
Configuration - Dial Peer Trunk Mode
codec preference
Use the Dial Peer codec preference command to set the codec preferences used to establish the codec
list offered during media negotiation. To delete a preference, see no codec preference command on
page 9-6.
Syntax:
(config-dpeer-trk)# codec preference {1|2|3} {g711alaw|
g711ulaw|g729}
Field
Definition
1|2|3
Enter the preference number. #1 being the first preference.
g711alaw
Set the codec preference to G.711 A-law.
g711ulaw
Set the codec preference to G.711 U-law.
g729
Set the codec preference to G.729.
Example: (config-dpeer-trk)# codec preference 1 g711alaw
Supported Platforms: Adit 3500, MSR
destination-pattern
Use the Dial Peer destination-pattern command to assign dial patterns to the trunk. To delete a pattern,
see no destination-pattern command on page 9-6.
Syntax:
(config-dpeer-trk)# destination-pattern dest-pattern
Field
Definition
dest-pattern
Enter the phone number pattern that must be matched for calls to be
routed to the trunk. Use ? as a wildcard that can be replaced with any
single digit. Use $ as a wildcard that can be replaced with multiple
digits (all digits following the $ are ignored).
Example: (config-dpeer-trk)# destination-pattern 555$
Supported Platforms: Adit 3500, MSR
9-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Dial Peer Trunk Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
9-3
Configuration - Dial Peer Trunk Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file.
Syntax:
(config-dpeer-trk)# end
Example: (config-dpeer-trk)# end
#
Supported Platforms: Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-dpeer-trk)# exit
Example: (config-dpeer-trk)# exit
(config)#
Supported Platforms: Adit 3500, MSR
fax-protocol
Use the Dial Peer fax-protocol command to configure the fax protocol.
Syntax:
(config-dpeer-trk)# fax-protocol {none|pass-through|t38}
Field
Definition
none
A Fax call would be treated as a normal voice call. Default.
pass-through
Will cause the line to transmit in G.711 mode, with echo cancellation
and silence suppression disabled, on detection of Fax tone.
t38
Upon detection of a Fax tone on the port, will cause the gateway to
negotiate a T.38 session with its peer and if successful, will enter T.38
Fax-relay mode. Will dynamically consume a T.38 token for the
session.
Note: For the MSR, T.38 will be supported in a future release.
Example: (config-dpeer-trk)# fax-protocol none
Supported Platforms: Adit 3500, MSR
9-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Dial Peer Trunk Mode
history
Use the history command to display commands that have been entered in this session.
Syntax:
(config-dpeer-trk)# history
Example: (config-dpeer-trk)# history
destination-pattern
fax-protocol none
modem-protocol pass-through
sip-authentication enable
strip-digits
history
Supported Platforms: Adit 3500, MSR
modem-protocol
Use the Dial Peer modem-protocol command to configure the modem protocol.
Syntax:
(config-dpeer-trk)# modem-protocol {none|pass-through}
Field
Definition
none
A Modem call would be treated as a normal voice call. Default.
pass-through
Will cause the line to transmit in G.711 mode, with echo cancellation
and silence suppression disabled, on detection of Modem tone.
Example: (config-dpeer-trk)# modem-protocol pass-though
Supported Platforms: Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
9-5
Configuration - Dial Peer Trunk Mode
no commands
no codec preference
Use the Dial Peer no codec preference command to remove a codec preference. To set the
preferences, see codec preference command on page 9-2.
Syntax:
(config-dpeer-trk)# no codec preference {1|2|3}
Field
Definition
1|2|3
Set the preference level. Range 1 - 3.
Example: (config-dpeer-trk)# no codec preference 1
Supported Platforms: Adit 3500, MSR
no destination-pattern
Use the Dial Peer no destination-pattern command to remove a destination pattern. To set the
destination pattern, see destination-pattern command on page 9-2.
Syntax:
(config-dpeer-trk)# no destination-pattern
Example: (config-dpeer-trk)# no destination-pattern
Supported Platforms: Adit 3500, MSR
no sip-authentication
Use the Dial Peer no sip-authentication command to disable SIP authentication. To configure SIP
authentication, see sip-authentication command on page 9-7.
Syntax:
(config-dpeer-trk)# no sip-authentication
Example: (config-dpeer-trk)# no sip-authentication
Supported Platforms: Adit 3500, MSR
9-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Dial Peer Trunk Mode
prefix
Use the Dial Peer prefix command to define the prefix of the phone number.
Syntax:
(config-dpeer-trk)# prefix prefix
Field
Definition
prefix
Prefix is the digits or a name to be added to the phone number after the
stripping process has been applied. Up to 10 digits may be entered.
Example: (config-dpeer-trk)# prefix 1303
Supported Platforms: Adit 3500, MSR
sip-authentication
Note: To delete SIP authentication, see no sip-authentication command on page 9-6.
sip-authentication enable
Use the Dial Peer sip-authentication enable command to enable SIP.
Syntax:
(config-dpeer-trk)# sip-authentication enable
Example: (config-dpeer-trk)# sip-authentication enable
Supported Platforms: Adit 3500, MSR
sip-authentication password
Use the Dial Peer sip-authentication password command to set the SIP password.
Syntax:
(config-dpeer-trk)# sip-authentication password password
Field
Definition
password
The password to be used when responding to authentication requests.
Example: (config-dpeer-trk)# sip-authentication password
test-password
Supported Platforms: Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
9-7
Configuration - Dial Peer Trunk Mode
sip-authentication username
Use the Dial Peer sip-authentication username command to set the SIP ID.
Syntax:
(config-dpeer-trk)# sip-authentication username username
Field
Definition
username
The User ID to be used when responding to authentication requests.
Default is the User ID of the line.
Example: (config-dpeer-trk)# sip-authentication username
test-user-1
Supported Platforms: Adit 3500, MSR
strip-digits
Use the Dial Peer strip-digits command to configure the number of digits (or characters) to be stripped
off from the left most digits in the phone number. Possible usages include stripping off the area code,
or the 3-digit office prefix.
Syntax:
(config-dpeer-trk)# strip-digits number
Field
Definition
number
Range is based on the defined phone number. Default is set to 0.
Example: (config-dpeer-trk)# strip-digits 4
Supported Platforms: Adit 3500, MSR
9-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
10
Configuration - Dial Peer VoIP Mode
The Dial Peer VoIP Configuration commands allow the user to configure the Dial Peer VoIP
parameters.
Enter this sub-group with the (config)# dial-peer voice voip port command from the Configuration
mode.
The Dial Peer VoIP commands are represented by the (config-dpeer-voip)# prompt.
Dial Peer VoIP Commands
•
•
•
•
•
•
•
•
•
•
destination-pattern
do
end
exit
history
no commands
prefix
session-target
strip-digits
user-id
Configuration - Dial Peer VoIP Mode
destination-pattern
Use the Dial Peer destination-pattern command to define the full telephone number to be used for a
dial peer. To delete a preference, see no destination-pattern command on page 10-5.
Syntax:
(config-dpeer-voip)# destination-pattern number
Field
Definition
number
Enter the phone number to be used for a dial peer.
Example: (config-dpeer-voip)# destination-pattern 5551212
Supported Platforms: Adit 3104, Adit 3500, MSR
10-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Dial Peer VoIP Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
10-3
Configuration - Dial Peer VoIP Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file.
Syntax:
(config-dpeer-voip) end
Example: (config-dpeer-voip)# end
#
Supported Platforms: Adit 3104, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-dpeer-voip)# exit
Example: (config-dpeer-voip)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3500, MSR
history
Use the history command to display commands that have been entered in this session.
Syntax:
(config-dpeer-voip)# history
Example: (config-dpeer-voip)# history
exit
destination-pattern ddddd
destination-pattern
modem-protocol none
sip-authentication
sip-authentication enable
history
Supported Platforms: Adit 3104, Adit 3500, MSR
10-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Dial Peer VoIP Mode
no commands
no destination-pattern
Use the Dial Peer no destination-pattern command to remove a destination pattern. To set the
destination pattern, see destination-pattern command on page 10-2.
Syntax:
(config-dpeer-voip)# no destination-pattern
Example: (config-dpeer-voip)# no destination-pattern
Supported Platforms: Adit 3104, Adit 3500, MSR
no prefix
Use the Dial Peer no prefix command to remove the prefix of the phone number. To define a prefix,
see prefix command on page 10-6.
Syntax:
(config-dpeer-voip)# no prefix
Example: (config-dpeer-voip)# no prefix 1303
Supported Platforms: Adit 3104, Adit 3500, MSR
no session-target
Use the Dial Peer no session-target command to remove session target. To configure a session
target, see session-target command on page 10-6.
Syntax:
(config-dpeer-voip)# no session-target
Example: (config-dpeer-voip)# no session target
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
10-5
Configuration - Dial Peer VoIP Mode
prefix
Use the Dial Peer prefix command to define the prefix of the phone number. To delete a prefix, see no
prefix command on page 10-5.
Syntax:
(config-dpeer-voip)# prefix prefix
Field
Definition
prefix
Prefix is the digits or a name to be added to the phone number after the
stripping process has been applied. Up to 10 digits may be entered.
Example: (config-dpeer-voip)# prefix 1303
Supported Platforms: Adit 3104, Adit 3500, MSR
session-target
Use the Dial Peer session-target command to configure the session target. To delete a target, see no
session-target command on page 10-5.
Syntax:
(config-dpeer-voip)# session-target {hostname hostname|
ip-address address|local fxs-number|proxy}
Field
Definition
hostname
Indicates that the domain name server will be used to resolve the name
of the IP address.
address
Enter the IP address of the dial peer.
fxs-number
Enter an FXS port.
Adit 3104: Range = 1 - 24.
Adit 3500: Range = 1 - 4.
MSR: Range = 1 - 48.
proxy
Set the session target to be routed through the proxy.
Example: (config-dpeer-voip)# session-target ip-address 192.168.1.100
Supported Platforms: Adit 3104, Adit 3500, MSR
10-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Dial Peer VoIP Mode
strip-digits
Use the Dial Peer strip-digits command to configure the number of digits (or characters) to be stripped
off from the left most digits in the phone number. Possible usages include stripping off the area code,
or the 3-digit office prefix.
Syntax:
(config-dpeer-voip)# strip-digits number
Field
Definition
number
Range is based on the defined phone number. Default is set to 0.
Example: (config-dpeer-voip)# strip-digits 4
Supported Platforms: Adit 3104, Adit 3500, MSR
user-id
Use the Dial Peer user-id command to configure a user ID for the line.
Syntax:
(config-dpeer-voip)# user-id user-id
Field
Definition
user-id
Enter a user ID for the line, with a maximum of 20 characters.
Example: (config-dpeer-voip)# user-id testname
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
10-7
Configuration - Dial Peer VoIP Mode
10-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
11
Configuration - Ethernet Interface Mode
The Ethernet Interface Configuration commands allow the user to configure the Ethernet interface
parameters.
Enter this sub-group with the (config)# interface ethernet command from the Configuration mode.
The Ethernet Interface commands are represented by the (config-int-eth-{n})# prompt.
Ethernet Interface Commands
• description
• ip ospf priority
• do
• ip ospf retransmit-interval
• end
• ip ospf transmit-delay
• exit
• ip primary-dns
• firewall
• ip proxy-arp
• full-duplex
• ip rip
• half-duplex
• ip route
• history
• ip route-mode
• ip address
• ip secondary-dns
• ip default-gateway
• metric
• ip default-route
• no commands
• ip dhcp
• release
• ip mtu
• remote-admin
• ip ospf authentication
• renew
• ip ospf authentication-key
• schedule-availability
• ip ospf cost
• shutdown
• ip ospf dead-interval
• sip-alg
• ip ospf disable
• speed
• ip ospf hello-interval
• tos
• ip ospf message-digest-key
Configuration - Ethernet Interface Mode
description
Use the Ethernet Interface description command to set the description for this Ethernet interface.
Syntax:
(config-int-eth-{n})# description text
Field
Definition
text
Enter a description for the Ethernet interface with a maximum of 64
characters.
Example: (config-int-eth-1)# description Eth#1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
11-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Ethernet Interface Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
11-3
Configuration - Ethernet Interface Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-int-eth-{n})# end
Example: (config-int-eth-1)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-int-eth-{n})# exit
Example: (config-int-eth-1)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
firewall
Use the firewall command to enable the configured firewall. To delete a preference, see no
firewall command on page 11-17.
Syntax:
(config-int-eth-{n})# firewall enable
Example: (config-int-eth-1)# firewall enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
11-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Ethernet Interface Mode
full-duplex
Use the Ethernet Interface full-duplex command to specify the Ethernet PHY (physical specifications)
mode to full duplex.
Syntax:
(config-int-eth-{n})# full-duplex
Example: (config-int-eth-1)# full-duplex
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
half-duplex
Use the Ethernet Interface half-duplex command to specify the Ethernet PHY (physical specifications)
mode to half duplex.
Syntax:
(config-int-eth-{n})# half-duplex
Example: (config-int-eth-1)# half-duplex
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
11-5
Configuration - Ethernet Interface Mode
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-int-eth-{n})# history
Example: (config-int-eth-1)# history
schedule-availability rule1
history
full-duplex
ip rip
ip rip enable
ip address
speed auto
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip address
Use the Ethernet Interface ip address command to set the IP address for the Ethernet port. To remove
an IP address, see no ip address command on page 11-17.
Syntax:
(config-int-eth-{n})# ip address {address mask mask [secondary]
|auto}
Field
Definition
address
Enter an IP address to assign to the Ethernet port.
mask
Enter a subnet mask for the Ethernet IP address.
auto
Use DHCP to assign an IP address.
secondary
This optional parameter, defines the address to be a secondary IP
address.
Example: (config-int-eth-1)# ip address 192.168.2.100 mask 255.255.255.0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
11-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Ethernet Interface Mode
ip default-gateway
Use the Ethernet Interface ip default-gateway command to set the default gateway for the Ethernet
port.
Syntax:
(config-int-eth-{n})# ip default-gateway address
Field
Definition
address
Enter a default gateway address to the Ethernet port.
Example: (config-int-eth-1)# ip default-gateway 192.168.100.150
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip default-route
Use the Ethernet Interface ip default-route command to enable the default route. To disable the default
route, see no ip default-route command on page 11-17.
Syntax:
(config-int-eth-{n})# ip default-route enable
Example: (config-int-eth-1)# ip default-route enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip dhcp
Use the Ethernet Interface ip dhcp command to enable the use of DHCP options 66 and 67 to
autoconfigure the system. To disable DHCP, see no ip dhcp command on page 11-17.
Syntax:
(config-int-eth-{n})# ip dhcp auto-provision
Example: (config-int-eth-1)# ip dhcp auto-provision
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
11-7
Configuration - Ethernet Interface Mode
ip mtu
Use the Ethernet Interface ip mtu command to set the Maximum Transmission Unit. Sets the largest
packet size (bytes) the network will allow to transmit.
Syntax:
(config-int-eth-{n})# ip mtu {size|auto}
Field
Definition
size
Allows the user to set the Maximum Transmission Unit (MTU).
size = range of 576 to 1500 bytes.
auto
Auto sets the MTU at 1500 bytes.
Example: (config-int-eth-1)# ip mtu auto
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
11-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Ethernet Interface Mode
ip ospf authentication
Use the Ethernet Interface ip ospf authentication command to enable the authentication method (either
message-digest or simple authentication) for this Ethernet interface. To remove the authentication type
for this interface set the parameter to null or see no ip ospf authentication command on page 11-18.
Note: If an optional parameter is not entered, the authentication method of simple authentication is
applied to the interface.
Syntax:
(config-int-eth-{n})# ip ospf authentication
[message-digest|null]
Field
Definition
message-digest
Optional parameter. Enables MD5 Authentication on the area.
null
Optional parameter. No authentication is used. Note: This is useful for
overriding password or message-digest authentication if configured
for an area.
Example: (config-int-eth-1)# ip ospf authentication message-digest
Note: The authentication key must be defined before this command is implemented.
Therefore if setting simple authentication:
Example: ip ospf authentication-key pass777
ip ospf authentication
Therefore if setting message-digest:
Example: ip ospf message-digest-key 1 md5 pass777
ip ospf authentication message-digest
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
11-9
Configuration - Ethernet Interface Mode
ip ospf authentication-key
Use the Ethernet Interface ip ospf authentication-key command to assign a password to be used by
neighboring routers, that are using OSPF’s simple password authentication.To remove a previously
assigned password, see no ip ospf authentication-key command on page 11-18.
Syntax:
(config-int-eth-{n})# ip ospf authentication-key password
Field
Definition
password
Enter a password, with up to 8 characters.
Example: (config-int-eth-1)# ip ospf authentication-key pass777
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf cost
Use the Ethernet Interface ip ospf cost command to define the cost of sending a packet on this Ethernet
interface. To reset the path cost to the default setting of 0, see no ip ospf cost command on page 11-18.
Syntax:
(config-int-eth-{n})# ip ospf cost cost
Field
Definition
cost
Range is 1-65535, with a default of 0.
Example: (config-int-eth-1)# ip ospf cost 5
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf dead-interval
Use the Ethernet Interface ip ospf dead-interval command to define the interval of time that no hello
packets have been seen before neighbors declare the router down. To reset the interval of time to the
default setting of 40 seconds, see no ip ospf dead-interval command on page 11-18.
Syntax:
(config-int-eth-{n})# ip ospf dead-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 40.
Note: This value must be the same for all nodes on the network.
Example: (config-int-eth-1)# ip ospf dead-interval 50
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
11-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Ethernet Interface Mode
ip ospf disable
Use the Ethernet Interface ip ospf disable command to disable OSPF processing on this interface. To
enable OSPF on this interface, see no ip ospf disable command on page 11-19.
Syntax:
(config-int-eth-{n})# ip ospf disable all
Example: (config-int-eth-1)# ip ospf disable all
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf hello-interval
Use the Ethernet Interface ip ospf hello-interval command to define the interval of time between hello
packets sent on the interface. To reset the interval of time to the default setting of the path cost to the
default setting of 10 seconds, see no ip ospf hello-interval command on page 11-19.
Syntax:
(config-int-eth-{n})# ip ospf hello-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 10.
Note: This value must be the same for all nodes on the network.
Example: (config-int-eth-1)# ip ospf hello-interval 12
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf message-digest-key
Use the Ethernet Interface ip ospf message-digest-key command to enable OSPF MD5 (MessageDigest) authentication. To remove an old MD5 key, see no ip ospf message-digest-key command on
page 11-19.
Syntax:
(config-int-eth-{n})# ip ospf message-digest-key key-id md5 key
Field
Definition
key-id
Enter an ID for this key. Range is 1-255.
key
Enter a alphanumeric password, with up to 8 characters.
Example: (config-int-eth-1)# ip ospf message-digest-key 1 md5 pass777
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
11-11
Configuration - Ethernet Interface Mode
ip ospf priority
Use the Ethernet Interface ip ospf priority command to set the router priority, which determines the
designated router for this network. To restore the default setting of priority 1, see no ip ospf
priority command on page 11-20.
Syntax:
(config-int-eth-{n})# ip ospf priority priority
Field
Definition
priority
Enter an ID for this key. Range is 0-255.
Example: (config-int-eth-1)# ip ospf priority 2
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf retransmit-interval
Use the Ethernet Interface ip ospf retransmit-interval command to define the interval of time between
link state advertisement retransmissions for adjacencies belonging to the interface. To restore the
default value of 5 seconds, see no ip ospf retransmit-interval command on page 11-20.
Syntax:
(config-int-eth-{n})# ip ospf retransmit-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 5.
Example: (config-int-eth-1)# ip ospf retransmit-interval 10
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf transmit-delay
Use the Ethernet Interface ip ospf transmit-delay command to define the estimated time to transmit a
link state update packet on the interface. To restore the default value of 1 second, see no ip ospf transmitdelay command on page 11-20.
Syntax:
(config-int-eth-{n})# ip ospf transmit-delay seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 1.
Example: (config-int-eth-1)# ip ospf retransmit-interval 10
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
11-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Ethernet Interface Mode
ip primary-dns
Use the Ethernet Interface ip primary-dns command to configure the primary DNS. To delete a
primary DNS, see no ip primary-dns command on page 11-20.
Syntax:
(config-int-eth-{n})# ip primary-dns address
Field
Definition
address
Enter the IP address of the primary server.
Example: (config-int-eth-1)# ip primary-dns 192.168.1.100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip proxy-arp
Use the Ethernet Interface ip proxy-arp command to enable proxy ARP on this interface. To disable
prosy ARP, see no ip proxy-arp command on page 11-21.
Syntax:
(config-int-eth-{n})# ip proxy-arp
Example: (config-int-eth-1)# ip proxy-arp
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
11-13
Configuration - Ethernet Interface Mode
ip rip
ip rip enable
Use the Ethernet Interface ip rip enable command to enable RIP on this interface. To disable RIP,
see no ip rip command on page 11-21.
Syntax:
(config-int-eth-{n})# ip rip enable
Example: (config-int-eth-1)# ip rip enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip rip receive-version
Use the Ethernet Interface ip rip receive-version command to configure the RIP receive messages
on this interface.
Syntax:
(config-int-eth-{n})# ip rip receive-version {1|2|1or2|none}
Field
Definition
1
Receive RIP version 1
2
Receive RIP version 2
1or2
Receive RIP version 1 and 2.
none
Set RIP version to none.
Example: (config-int-eth-1)# ip rip receive-version none
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip rip send-version
Use the Ethernet Interface ip rip send-version command to configure the send RIP messages on this
interface.
Syntax:
(config-int-eth-{n})# ip rip send-version {1|2-bcast|
2-mcast|none}
Field
Definition
1
Send RIP version 1.
2-bcast
Send RIP version 2 - Broadcast.
2-mcast
Send RIP version 2 - Multicast.
none
Set send RIP version to none.
Example: (config-int-eth-1)# ip rip send-version 2-bcast
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
11-14
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Ethernet Interface Mode
ip route
Use the Ethernet Interface ip route command to configure the static routes on this interface. To delete
a route, see no ip route command on page 11-21.
Syntax:
(config-int-eth-{n})# ip route dest-ip-addr mask mask gateway
gateway metric metric
Field
Definition
dest-ip-addr
Enter the destination IP address.
mask
Enter the mask of the above address.
gateway
Enter the gateway IP address.
metric
Metric of IP network on this interface in the Routing Table. Range is
0-255, with a default is 10.
Example: (config-int-eth-1)# ip route 192.168.100.200 mask 255.255.255.0
gateway 192.168.100.254 metric 125
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip route-mode
Use the Ethernet Interface ip route-mode command to configure the routing mode.
Syntax:
(config-int-eth-{n})# ip route-mode {napt|route}
Field
Definition
napt
Set to NAPT mode. Default. NAPT is used if doing private IPs on the
Ethernet side or if you want to hide specific publics on the internal
side.
route
Set to Route mode. Routing is used if public is visible on both sides.
Example: (config-int-eth-1)# ip route-mode napt
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
11-15
Configuration - Ethernet Interface Mode
ip secondary-dns
Use the Ethernet Interface ip secondary-dns command to configure the secondary DNS. To delete a
secondary DNS address, see no ip secondary-dns command on page 11-21.
Syntax:
(config-int-eth-{n})# ip secondary-dns address
Field
Definition
address
Enter the IP address of the secondary Domain Name Server (DNS).
Example: (config-int-eth-1)# ip secondary-dns 192.168.1.200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
metric
Use the Ethernet Interface metric command to configure the Metric of the IP network on this interface.
Syntax:
(config-int-eth-{n})# metric metric
Field
Definition
metric
Range is 0-255, with a default is 10.
Example: (config-int-eth-1)# metric 150
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
11-16
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Ethernet Interface Mode
no commands
no firewall
Use the no firewall command to disable the configured firewall. To enable the firewall, see
firewall command on page 11-4.
Syntax:
(config-int-eth-{n})# no firewall
Example: (config-int-eth-1)# no firewall
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip address
Use the Ethernet Interface no ip address command to remove the IP address from the alias. To set
the Ethernet IP address, see ip address command on page 11-6.
Syntax:
(config-int-eth-{n})# no ip address address
Field
Definition
address
Enter the IP address to remove.
Example: (config-int-eth-1)# no ip address 192.168.1.100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip default-route
Use the Ethernet Interface no ip default-route command to disable the default route. To set the
default IP address, see ip default-route command on page 11-7.
Syntax:
(config-int-eth-{n})# no ip default-route
Example: (config-int-eth-1)# no ip default-route
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip dhcp
Use the Ethernet Interface no ip dhcp command to disable the use of DHCP options 66 and 67 to
autoconfigure the system. To enable DHCP, see ip dhcp command on page 11-7.
Syntax:
(config-int-eth-{n})# no ip dhcp auto-provision
Example: (config-int-eth-1)# no ip dhcp auto-provision
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
11-17
Configuration - Ethernet Interface Mode
no ip ospf authentication
Use the Ethernet Interface no ip ospf authentication command to disable the authentication
method for this Ethernet interface. To enable the authentication type for this interface see ip ospf
authentication command on page 11-9.
Syntax:
(config-int-eth-{n})# no ip ospf authentication
Example: (config-int-eth-{n})# no ip ospf authentication
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf authentication-key
Use the Ethernet Interface no ip ospf authentication-key command to remove a password to be
used by neighboring routers, that are using OSPF’s simple password authentication.To assign a
password, see ip ospf authentication-key command on page 11-10.
Syntax:
(config-int-eth-{n})# no ip ospf authentication
Example: (config-int-eth-1)# no ip ospf authentication-key
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf cost
Use the Ethernet Interface no ip ospf cost command to reset the cost path to the default setting of
0. To define the cost of sending a packet on this Ethernet interface, see ip ospf cost command on
page 11-10.
Syntax:
(config-int-eth-{n})# no ip ospf cost
Example: (config-int-eth-1)# no ip ospf cost
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf dead-interval
Use the Ethernet Interface no ip ospf dead-interval command to reset the interval of time to the
default setting of 40 seconds. To define the interval of time that no hello packets have been seen
before neighbors declare the router down, see ip ospf dead-interval command on page 11-10.
Syntax:
(config-int-eth-{n})# no ip ospf dead-interval
Example: (config-int-eth-1)# no ip ospf dead-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
11-18
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Ethernet Interface Mode
no ip ospf disable
Use the Ethernet Interface no ip ospf disable command to enable OSPF processing on this
interface. To disable OSPF on this interface, see ip ospf disable command on page 11-11.
Syntax:
(config-int-eth-{n})# ip ospf disable all
Example: (config-int-eth-1)# ip ospf disable all
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf hello-interval
Use the Ethernet Interface no ip ospf hello-interval command to reset the interval of time to the
default setting of the path cost to the default setting of 10 seconds. To define the interval of time
between hello packets sent on the interface, see ip ospf hello-interval command on page 11-11.
Syntax:
(config-int-eth-{n})# no ip ospf hello-interval
Example: (config-int-eth-1)# no ip ospf hello-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf message-digest-key
Use the Ethernet Interface no ip ospf message-digest-key command to remove an old MD5 key.
To enable OSPF MD5 (Message-Digest) authentication, see ip ospf message-digest-key command
on page 11-11.
Syntax:
(config-int-eth-{n})# no ip ospf message-digest-key key-id
Field
Definition
key-id
Enter an ID for this key. Range is 1-255.
Example: (config-int-eth-1)# no ip ospf message-digest-key 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
11-19
Configuration - Ethernet Interface Mode
no ip ospf priority
Use the Ethernet Interface no ip ospf priority command to set the router priority to the default
setting of priority 1. To set the router priority, which determines the designated router for this
network, see ip ospf priority command on page 11-12.
Syntax:
(config-int-eth-{n})# no ip ospf priority
Example: (config-int-eth-1)# no ip ospf priority
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf retransmit-interval
Use the Ethernet Interface ip ospf retransmit-interval command to restore the default value of 5
seconds. To define the interval of time between link state advertisement retransmissions for
adjacencies belonging to the interface, see ip ospf retransmit-interval command on page 11-12.
Syntax:
(config-int-eth-{n})# no ip ospf retransmit-interval
Example: (config-int-eth-1)# no ip ospf retransmit-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf transmit-delay
Use the Ethernet Interface no ip ospf transmit-delay command to restore the default value of 1
second. To define the estimated time to transmit a link state update packet on the interface, see ip
ospf transmit-delay command on page 11-12.
Syntax:
(config-int-eth-{n})# no ip ospf transmit-delay
Example: (config-int-eth-1)# no ip ospf transmit-delay
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip primary-dns
Use the Ethernet Interface no primary-dns command to disable the primary DNS. To set the DNS
primary IP address, see ip primary-dns command on page 11-13.
Syntax:
(config-int-eth-{n})# no ip primary-dns
Example: (config-int-eth-1)# no ip primary-dns
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
11-20
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Ethernet Interface Mode
no ip proxy-arp
Use the Ethernet Interface no ip proxy-arp command to disable the proxy ARP on this interface.
To enable proxy ARP, see ip proxy-arp command on page 11-13.
Syntax:
(config-int-eth-{n})# no ip proxy-arp
Example: (config-int-eth-1)# no ip proxy-arp
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip rip
Use the Ethernet Interface no ip rip command to disable RIP on this interface. To enable RIP, see
ip rip command on page 11-14.
Syntax:
(config-int-eth-{n})# no ip rip
Example: (config-int-eth-1)# no ip rip
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip route
Use the Ethernet Interface no ip route command remove an IP route. To add a route, see ip
route command on page 11-15.
Syntax:
(config-int-eth-{n})# no ip route dest-ip-addr gateway
Field
Definition
dest-ip-addr
Enter destination IP address to remove.
gateway
Enter gateway IP address to remove.
Example: (config-int-eth-1)# no ip route 192.168.100.200
192.168.100.254
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip secondary-dns
Use the Ethernet Interface no secondary-dns command to disable the secondary DNS. To enable
the secondary DNS, see ip secondary-dns command on page 11-16.
Syntax:
(config-int-eth-{n})# no ip secondary-dns
Example: (config-int-eth-1)# no ip secondary-dns
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
11-21
Configuration - Ethernet Interface Mode
no remote-admin
Use the Ethernet Interface no remote-admin command to disable remote access on this interface.
To enable remote access, see remote-admin command on page 11-23.
Syntax:
(config-int-eth-{n})# no remote-admin
Example: (config-int-eth-1)# no remote-admin
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no schedule-availability
Use the Ethernet Interface no schedule-availability command to disable a schedule rule. To create
a rule, see schedule-availability command on page 11-24.
Syntax:
(config-int-eth-{n})# no schedule-availability
Example: (config-int-eth-1)# no schedule-availability
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no shutdown
Use the Ethernet Interface no shutdown command to set the Ethernet port up (In-Service). To set
the Ethernet port down (Out-of-Service), see shutdown command on page 11-24.
Syntax:
(config-int-eth-{n})# no shutdown
Example: (config-int-eth-2)# no shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no sip-alg
Use the Ethernet Interface no sip-alg command to disable SIP ALG on this interface. To enable sip
alg, see sip-alg command on page 11-24.
Syntax:
(config-int-eth-{n})# no sip-alg
Example: (config-int-eth-1)# no sip-alg
Supported Platforms: Adit 3104, Adit 3500, MSR
11-22
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Ethernet Interface Mode
no tos ip
Use the Ethernet Interface no tos ip command to disable IP TOS marking. To enable TOS marking,
see tos command on page 11-25.
Syntax:
(config-int-eth-{n})# no tos ip
Example: (config-int-eth-1)# no tos ip
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
release
Use the Ethernet Interface release command to release the DHCP lease.
Syntax:
(config-int-eth-{n})# release
Example: (config-int-eth-1)# release
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
remote-admin
Use the Ethernet Interface remote admin command to enable Remote Access on this interface. To
disable remote access, see no remote-admin command on page 11-22.
Syntax:
(config-int-eth-{n})# remote-admin enable
Example: (config-int-eth-1)# remote-admin enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
renew
Use the Ethernet Interface renew command to renew the DHCP lease.
Syntax:
(config-int-eth-{n})# renew
Example: (config-int-eth-1)# renew
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
11-23
Configuration - Ethernet Interface Mode
schedule-availability
Use the Ethernet Interface schedule-availability command to apply a schedule rule to this interface. To
delete a schedule, see no schedule-availability command on page 11-22.
Syntax:
(config-int-eth-{n})# schedule-availability time-range
schedule-id
Field
Definition
schedule-id
Enter an existing schedule rule name. See time-range command on
page 4-62 to set the schedule-id
Example: (config-int-eth-1)# schedule-availability time-range 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
shutdown
Use the Ethernet Interface shutdown command to set the Ethernet port down (Out-of-Service). Note:
This command is not allowed if you are in the Ethernet 1 mode. To set the Ethernet port up (In-Service),
see no shutdown command on page 11-22.
Syntax:
(config-int-eth-{n})# shutdown
Example: (config-int-eth-2)# shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
sip-alg
Use the Ethernet Interface sip-alg command to enable SIP ALG on this interface. To disable SIP ALG,
see no sip-alg command on page 11-22.
Syntax:
(config-int-eth-{n})# sip-alg enable
Example: (config-int-eth-1)# sip-alg enable
Supported Platforms: Adit 3104, Adit 3500, MSR
11-24
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Ethernet Interface Mode
speed
Use the Ethernet Interface speed command to specify the Ethernet PHY (physical specifications) speed.
Syntax:
(config-int-eth-{n})# speed {10|100|auto}
Field
Definition
10
10 Mbps speed .
100
100 Mbps speed.
auto
Auto-negotiate the speed for the interface. Default.
Note: Setting speed to auto will set the duplex to auto.
Example: (config-int-eth-1)# speed 100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
tos
Use the Ethernet Interface tos command to configure IP TOS marking. To disable TOS marking, see no
tos ip command on page 11-23.
Syntax:
(config-int-eth-{n})# tos ip {enable|value hex-value}
Field
Definition
enable
Enable IP TOS marking.
hex-value
Hex value, range 0x00-0xFF, default is 0x00
Example: (config-int-eth-1)# tos ip value 0xff
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
11-25
Configuration - Ethernet Interface Mode
11-26
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
12
Configuration - Multilink Interface Mode
The Multilink Interface Configuration commands allow the user to configure the MLPPP parameters.
Enter this sub-group with the (config)# interface multilink number command from the Configuration
mode. The Multilink Interface commands are represented by the (config-int-mlink-{n})# prompt.
Note: Before configuring MLPPP parameters, you must create a multilink group from the
corresponding Serial interface. Use the multilink-group command to create the group.
Multilink Interface Commands
• description
• ip rip
• do
• ip route
• end
• ip route-mode
• exit
• ip secondary-dns
• firewall
• metric
• history
• no commands
• ip address
• ppp authentication
• ip default-route
• ppp encryption
• ip mtu
• ppp exec-timeout
• ip ospf authentication
• ppp link-fragmentation
• ip ospf authentication-key
• ppp on-demand
• ip ospf cost
• ppp password
• ip ospf dead-interval
• ppp qos-interleaving
• ip ospf disable
• ppp restart-timer
• ip ospf hello-interval
• ppp time-btwn-reconnect
• ip ospf message-digest-key
• ppp username
• ip ospf priority
• schedule-availability
• ip ospf retransmit-interval
• shutdown
• ip ospf transmit-delay
• sip-alg
• ip primary-dns
Configuration - Multilink Interface Mode
description
Use the Multilink Interface description command to set the description for this Multilink interface.
Syntax:
(config-int-mlink-{n})# description text
Field
Definition
text
Enter a description for the Multilink interface with a maximum of 64
characters.
Example: (config-int-mlink-1)# description MLPPP1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
12-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Multilink Interface Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
12-3
Configuration - Multilink Interface Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-int-mlink-{n})# end
Example: (config-int-mlink-1)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-int-mlink-{n})# exit
Example: (config-int-mlink-1)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
firewall
Use the Multilink interface firewall command to enable the firewall on this interface. To disable the
firewall, see no firewall command on page 12-14.
Syntax:
(config-int-mlink-{n})# firewall enable
Example: (config-int-mlink-1)# firewall enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
12-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Multilink Interface Mode
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-int-mlink-{n})# history
Example: (config-int-mlink-1)# history
description testdesc
firewall enable
ip rip enable
ppp authentication pap
ppp encryption 128-bit
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip address
Use the Multilink Interface ip address command to configure the MLPPP IP address. To remove an IP
address, see no ip address command on page 12-14.
Syntax:
(config-int-mlink-{n})# ip address {address mask
mask|auto|unnumbered} [secondary]
Field
Definition
address
Enter an IP address to assign to the port.
mask
Enter a subnet mask for the IP address.
auto
Uses IPCP to assign an IP address.
unnumbered
Set the Multilink IP address to unnumbered.
secondary
This optional parameter, defines the address to be a secondary IP
address.
Example: (config-int-mlink-1)# ip address 192.168.2.100 mask
255.255.255.0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
12-5
Configuration - Multilink Interface Mode
ip default-route
Use the Multilink Interface ip default-route command to enable the default route. To disable the default
route, see no ip default-route command on page 12-14.
Syntax:
(config-int-mlink-{n})# ip default-route enable
Example: (config-int-mlink-1)# ip default-route enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip mtu
Use the Multilink Interface ip mtu command to set the Maximum Transmission Unit. Sets the largest
packet size (bytes) the network will allow to transmit.
Syntax:
(config-int-mlink-{n})# ip mtu {size|auto}
Field
Definition
size
Allows the user to set the Maximum Transmission Unit (MTU).
size = range of 576 to 1500 bytes.
auto
Auto sets the MTU at 1500 bytes.
Example: (config-int-mlink-1)# ip mtu auto
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
12-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Multilink Interface Mode
ip ospf authentication
Use the Multilink Interface ip ospf authentication command to enable the authentication method
(either message-digest or simple authentication) for this Multilink interface. To remove the
authentication type for this interface set the parameter to null or see no ip ospf authentication command
on page 12-14.
Note: If an optional parameter is not entered, the authentication method of simple authentication is
applied to the interface.
Syntax:
(config-int-mlink-{n})# ip ospf authentication
[message-digest|null]
Field
Definition
message-digest
Optional parameter. Enables MD5 Authentication on the area.
null
Optional parameter. No authentication is used. Note: This is useful for
overriding password or message-digest authentication if configured
for an area.
Example: (config-int-mlink-1)# ip ospf authentication message-digest
Note: The authentication key must be defined before this command is implemented.
Therefore if setting simple authentication:
Example: ip ospf authentication-key pass777
ip ospf authentication
Therefore if setting message-digest:
Example: ip ospf message-digest-key 1 md5 pass777
ip ospf authentication message-digest
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
12-7
Configuration - Multilink Interface Mode
ip ospf authentication-key
Use the Multilink Interface ip ospf authentication-key command to assign a password to be used by
neighboring routers, that are using OSPF’s simple password authentication.To remove a previously
assigned password, see no ip ospf authentication-key command on page 12-15.
Syntax:
(config-int-mlink-{n})# ip ospf authentication-key password
Field
Definition
password
Enter a password, with up to 8 characters.
Example: (config-int-mlink-1)# ip ospf authentication-key pass777
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf cost
Use the Multilink Interface ip ospf cost command to define the cost of sending a packet on this
Multilink interface. To reset the path cost to the default setting of 0, see no ip ospf cost command on
page 12-15.
Syntax:
(config-int-mlink-{n})# ip ospf cost cost
Field
Definition
cost
Range is 1-65535, with a default of 0.
Example: (config-int-mlink-1)# ip ospf cost 5
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf dead-interval
Use the Multilink Interface ip ospf dead-interval command to define the interval of time that no hello
packets have been seen before neighbors declare the router down. To reset the interval of time to the
default setting of 40 seconds, see no ip ospf dead-interval command on page 12-15.
Syntax:
(config-int-mlink-{n})# ip ospf dead-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 40.
This value must be the same for all nodes on the network.
Example: (config-int-mlink-1)# ip ospf dead-interval 50
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
12-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Multilink Interface Mode
ip ospf disable
Use the Multilink Interface ip ospf disable command to disable OSPF processing on this interface. To
enable OSPF on this interface, see no ip ospf disable command on page 12-15.
Syntax:
(config-int-mlink-{n})# ip ospf disable all
Example: (config-int-mlink-1)# ip ospf disable all
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf hello-interval
Use the Multilink Interface ip ospf hello-interval command to define the interval of time between hello
packets that sent on the interface. To reset the interval of time to the default setting of the path cost to
the default setting of 10 seconds, see no ip ospf hello-interval command on page 12-16.
Syntax:
(config-int-mlink-{n})# ip ospf hello-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 10.
This value must be the same for all nodes on the network.
Example: (config-int-mlink-1)# ip ospf hello-interval 12
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf message-digest-key
Use the Multilink Interface ip ospf message-digest-key command to enable OSPF MD5 (MessageDigest) authentication. To remove an old MD5 key, see no ip ospf message-digest-key command on
page 12-16.
Syntax:
(config-int-mlink-{n})# ip ospf message-digest-key key-id md5
key
Field
Definition
key-id
Enter an ID for this key. Range is 1-255.
key
Enter a alphanumeric password, with up to 8 characters.
Example: (config-int-mlink-1)# ip ospf message-digest-key 1 md5 key1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
12-9
Configuration - Multilink Interface Mode
ip ospf priority
Use the Multilink Interface ip ospf priority command to set the router priority, which determines the
designated router for this network. To restore the default setting of priority 1, see no ip ospf priority
command on page 12-16.
Syntax:
(config-int-mlink-{n})# ip ospf priority priority
Field
Definition
priority
Enter an ID for this key. Range is 0-255.
Example: (config-int-mlink-1)# ip ospf priority 2
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf retransmit-interval
Use the Multilink Interface ip ospf retransmit-interval command to define the interval of time
between link state advertisement retransmissions for adjacencies belonging to the interface. To restore
the default value of 5 seconds, see no ip ospf retransmit-interval command on page 12-17.
Syntax:
(config-int-mlink-{n})# ip ospf retransmit-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 5.
Example: (config-int-mlink-1)# ip ospf retransmit-interval 10
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf transmit-delay
Use the Multilink Interface ip ospf transmit-delay command to define the estimated time to transmit a
link state update packet on the interface. To restore the default value of 1 second, see no ip ospf transmitdelay command on page 12-17.
Syntax:
(config-int-mlink-{n})# ip ospf transmit-delay seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 1.
Example: (config-int-mlink-1)# ip ospf retransmit-interval 10
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
12-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Multilink Interface Mode
ip primary-dns
Use the Multilink Interface ip primary-dns command to configure the primary DNS. To delete a
primary DNS, see no ip primary-dns command on page 12-17.
Syntax:
(config-int-mlink-{n})# ip primary-dns address
Field
Definition
address
Enter the IP address of the primary server.
Example: (config-int-mlink-1)# ip primary-dns 10.10.5.100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip rip
ip rip enable
Use the Multilink Interface ip rip enable command to enable RIP on this interface. To disable RIP,
see no ip rip command on page 12-17.
Syntax:
(config-int-mlink-{n})# ip rip enable
Example: (config-int-mlink-1)# ip rip enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip rip receive-version
Use the Multilink Interface ip rip receive-version command to configure the RIP receive messages
on this interface.
Syntax:
(config-int-mlink-{n})# ip rip receive-version {1|2|1or2|none}
Field
Definition
1|2|1or2
Receive RIP version 1
Receive RIP version 2
Receive RIP version 1 and 2
none
Set RIP version to none.
Example: (config-int-mlink-1)# ip rip receive-version none
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
12-11
Configuration - Multilink Interface Mode
ip rip send-version
Use the Multilink Interface ip rip send-version command to configure the send RIP messages on
this interface.
Syntax:
(config-int-mlink-{n})# ip rip send-version {1|2-bcast|2-mcast
|none}
Field
Definition
1
Send RIP version 1.
2-bcast
Send RIP version 2 - Broadcast.
2-mcast
Send RIP version 2 - Multicast.
none
Set RIP version to none.
Example: (config-int-mlink-1)# ip rip send-version 2-bcast
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip route
Use the Multilink Interface ip route command to configure the IP routing on this interface. To delete a
route, see no ip route command on page 12-18.
Syntax:
(config-int-mlink-{n})# ip route dest-ip-addr mask mask gateway
gateway metric metric
Field
Definition
dest-ip-addr
Enter the destination IP address.
mask
Enter the mask of the above address.
gateway
Enter the gateway IP address.
metric
Metric of IP network on this interface in Routing Table. Range is 0255, with a default is 10.
Example: (config-int-mlink-1)# ip route 192.168.100.200 mask
255.255.255.0 gateway 192.168.100.254 mask 125
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
12-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Multilink Interface Mode
ip route-mode
Use the Multilink Interface ip route-mode command to configure the routing mode.
Syntax:
(config-int-mlink-{n})# ip route-mode {napt|route}
Field
Definition
napt
Set to NAPT mode. Default.
NAPT is used if doing private IPs on the Ethernet side or if you want
to hide specific publics on the internal side.
route
Set to Route mode. Routing is used if public is visible on both sides.
Example: (config-int-mlink-1)# ip route-mode napt
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip secondary-dns
Use the Multilink Interface ip secondary-dns command to configure the secondary DNS. To delete a
secondary DNS address, see no ip secondary-dns command on page 12-18.
Syntax:
(config-int-mlink-{n})# ip secondary-dns address
Field
Definition
address
Enter the IP address of the secondary Domain Name Server (DNS).
Example: (config-int-mlink-1)# ip secondary-dns 192.168.1.200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
metric
Use the Multilink Interface metric command to configure the Metric of the IP network on this interface.
Syntax:
(config-int-mlink-{n})# metric metric
Field
Definition
metric
Range is 0-255, with a default is 10.
Example: (config-int-mlink-1)# metric 150
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
12-13
Configuration - Multilink Interface Mode
no commands
no firewall
Use the Multilink Interface no firewall command to disable the configured firewall. To enable the
firewall on this interface, see firewall command on page 12-4.
Syntax:
(config-int-mlink-{n})# no firewall
Example: (config-int-mlink-1)# no firewall
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip address
Use the Multilink Interface no ip address command to remove the IP address assigned to the port.
To set the Ethernet IP address, see ip address command on page 12-5
Syntax:
(config-int-mlink-{n})# no ip address address
Field
Definition
address
Enter the IP address to remove.
Example: (config-int-mlink-1)# no ip address 192.168.1.100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip default-route
Use the Multilink Interface no ip default-route command to disable the default route. To set the
default IP address, see ip default-route command on page 12-6.
Syntax:
(config-int-mlink-{n})# no ip default-route
Example: (config-int-mlink-1)# no ip default-route
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf authentication
Use the Multilink Interface no ip ospf authentication command to disable the authentication
method for this Multilink interface. To enable the authentication type for this interface see ip ospf
authentication command on page 12-7.
Syntax:
(config-int-mlink-{n})# no ip ospf authentication
Example: (config-int-mlink-{n})# no ip ospf authentication
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
12-14
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Multilink Interface Mode
no ip ospf authentication-key
Use the Multilink Interface no ip ospf authentication-key command to remove a password to be
used by neighboring routers, that are using OSPF’s simple password authentication. To assign a
password, see ip ospf authentication-key command on page 12-8.
Syntax:
(config-int-mlink-{n})# no ip ospf authentication
Example: (config-int-mlink-1)# no ip ospf authentication-key
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf cost
Use the Multilink Interface no ip ospf cost command to reset the cost path to the default setting of
0. To define the cost of sending a packet on this Multilink interface, see ip ospf cost command on
page 12-8.
Syntax:
(config-int-mlink-{n})# no ip ospf cost
Example: (config-int-mlink-1)# no ip ospf cost
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf dead-interval
Use the Multilink Interface no ip ospf dead-interval command to reset the interval of time to the
default setting of 40 seconds. To define the interval of time that no hello packets have been seen
before neighbors declare the router down, see ip ospf dead-interval command on page 12-8.
Syntax:
(config-int-mlink-{n})# no ip ospf dead-interval
Example: (config-int-mlink-1)# no ip ospf dead-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf disable
Use the Multilink Interface no ip ospf disable command to enable OSPF processing on this
interface. To disable OSPF on this interface, see ip ospf disable command on page 12-9.
Syntax:
(config-int-mlink-{n})# ip ospf disable all
Example: (config-int-mlink-1)# ip ospf disable all
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
12-15
Configuration - Multilink Interface Mode
no ip ospf hello-interval
Use the Multilink Interface no ip ospf hello-interval command to reset the interval of time to the
default setting of the path cost to the default setting of 10 seconds. To define the interval of time
between hello packets sent on the interface, see ip ospf hello-interval command on page 12-9.
Syntax:
(config-int-mlink-{n})# no ip ospf hello-interval
Example: (config-int-mlink-1)# no ip ospf hello-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf message-digest-key
Use the Multilink Interface no ip ospf message-digest-key command to remove an old MD5 key.
To enable OSPF MD5 (Message-Digest) authentication, see ip ospf message-digest-key command
on page 12-9.
Syntax:
(config-int-mlink-{n})# no ip ospf message-digest-key key-id
Field
Definition
key-id
Enter an ID for this key. Range is 1-255.
Example: (config-int-mlink-1)# no ip ospf message-digest-key 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf priority
Use the Multilink Interface no ip ospf priority command to set the router priority to the default
setting of priority 1. To set the router priority, which determines the designated router for this
network, see ip ospf priority command on page 12-10.
Syntax:
(config-int-mlink-{n})# no ip ospf priority
Example: (config-int-mlink-1)# no ip ospf priority
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
12-16
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Multilink Interface Mode
no ip ospf retransmit-interval
Use the Multilink Interface ip ospf retransmit-interval command to restore the default value of 5
seconds. To define the interval of time between link state advertisement retransmissions for
adjacencies belonging to the interface, see ip ospf retransmit-interval command on page 12-10.
Syntax:
(config-int-mlink-{n})# no ip ospf retransmit-interval
Example: (config-int-mlink-1)# no ip ospf retransmit-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf transmit-delay
Use the Multilink Interface no ip ospf transmit-delay command to restore the default value of 1
second. To define the estimated time to transmit a link state update packet on the interface, see ip
ospf transmit-delay command on page 12-10.
Syntax:
(config-int-mlink-{n})# no ip ospf transmit-delay
Example: (config-int-mlink-1)# no ip ospf transmit-delay
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip primary-dns
Use the Multilink Interface no primary-dns command to disable the primary DNS. To set the DNS
primary IP address, see ip primary-dns command on page 12-11.
Syntax:
(config-int-mlink-{n})# no ip primary-dns
Example: (config-int-mlink-1)# no ip primary-dns
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip rip
Use the Multilink Interface no ip rip command to disable RIP on this interface. To enable RIP, see
ip rip command on page 12-11.
Syntax:
(config-int-mlink-{n})# no ip rip
Example: (config-int-mlink-1)# no ip rip
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
12-17
Configuration - Multilink Interface Mode
no ip route
Use the Multilink Interface no ip route command remove an IP route. To add a route, see ip route
command on page 12-12.
Syntax:
(config-int-mlink-{n})# no ip route dest-ip-addr gateway
Field
Definition
dest-ip-addr
Enter destination IP address to remove.
gateway
Enter gateway IP address to remove.
Example: (config-int-mlink-1)# no ip route 192.168.100.200
192.168.100.254
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip secondary-dns
Use the Multilink Interface no secondary-dns command to disable the secondary DNS. To enable
the secondary DNS, see ip secondary-dns command on page 12-13.
Syntax:
(config-int-mlink-{n})# no ip secondary-dns
Example: (config-int-mlink-1)# no ip secondary-dns
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp authentication
Use the Multilink Interface no ppp authentication command disable PPP authentication. To
enable PPP authentication, see ppp authentication command on page 12-21.
Syntax:
(config-int-mlink-{n})# no ppp authentication
Example: (config-int-mlink-1)# no ppp authentication
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp encryption
Use the Multilink Interface no ppp encryption command to disable PPP encryption. To enable PPP
encryption, see ppp encryption command on page 12-21.
Syntax:
(config-int-mlink-{n})# no ppp encryption
Example: (config-int-mlink-1)# no ppp encryption
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
12-18
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Multilink Interface Mode
no ppp on-demand
Use the Multilink Interface no ppp on-demand command to disable PPP on-demand. To enable
PPP on demand, see ppp on-demand command on page 12-22.
Syntax:
(config-int-mlink-{n})# no ppp on-demand
Example: (config-int-mlink-1)# no ppp on-demand
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp password
Use the Multilink Interface no ppp password command to remove the PPP password. To set the
PPP password, see ppp password command on page 12-22.
Syntax:
(config-int-mlink-{n})# no ppp password
Example: (config-int-mlink-1)# no ppp password
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp qos interleaving
Use the Multilink Interface no ppp qos interleaving command to disable PPP QoS interleaving.
To enable PPP QoS interleaving, see ppp qos-interleaving command on page 12-23.
Syntax:
(config-int-mlink-{n})# no ppp qos interleaving
Example: (config-int-mlink-1)# no ppp qos interleaving
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp username
Use the Multilink Interface no ppp username command remove the PPP username. To set a PPP
user, see ppp username command on page 12-24.
Syntax:
(config-int-mlink-{n})# no ppp username
Example: (config-int-mlink-1)# no ppp username
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
12-19
Configuration - Multilink Interface Mode
no schedule-availability
Use the Multilink Interface no schedule-availability command to disable a schedule rule. To add
a rule, see schedule-availability command on page 12-24.
Syntax:
(config-int-mlink-{n})# no schedule-availability
Example: (config-int-mlink-1)# no schedule-availability
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no shutdown
Use the Multilink Interface no shutdown command to set the Multilink port up (In-Service). To set
the interface down (Out-of-Service), see shutdown command on page 12-24.
Syntax:
(config-int-mlink-{n})# no shutdown
Example: (config-int-mlink-1)# no shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no sip-alg
Use the Multilink Interface no sip-alg command to disable SIP ALG on this interface. To enable
SIP ALG, see sip-alg command on page 12-25.
Syntax:
(config-int-mlink-{n})# no sip-alg
Example: (config-int-mlink-1)# no sip-alg
Supported Platforms: Adit 3104, Adit 3500, MSR
12-20
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Multilink Interface Mode
ppp authentication
Use the Multilink Interface ppp authentication command to configure the support of authentication
types for the password. To disable PPP authentication, see no ppp authentication command on
page 12-18.
Syntax:
(config-int-mlink-{n})# ppp authentication {chap|ms-chapv1|
ms-chapv2|pap}
Field
Definition
chap
Support Challenge Handshake Authentication (CHAP)
ms-chapv1
Support Microsoft CHAP (MS-CHAP).
ms-chapv2
Support Microsoft CHAP Version 2 (MS-CHAPv2).
pap
Support an unencrypted password.
Example: (config-int-mlink-1)# ppp authentication chap
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp encryption
Use the Multilink Interface ppp encryption command to configure the PPP encryption. To disable PPP
encryption, see no ppp encryption command on page 12-18.
Syntax:
(config-int-mlink-{n})# ppp encryption {40-bit|128-bit}
Field
Definition
40-bit
Support Encryption (40 bit keys)
128-bit
Support Maximum Strength Encryption (128 bit keys)
Example: (config-int-mlink-1)# ppp encryption 40-bit
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp exec-timeout
Use the Multilink Interface ppp exec-timeout command to configure the PPP maximum idle time
before hangup.
Syntax:
(config-int-mlink-{n})# ppp exec-timeout minutes
Field
Definition
minutes
Range is 0 - 99999 minutes.
Example: (config-int-mlink-1)# ppp exec-timeout 150
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
12-21
Configuration - Multilink Interface Mode
ppp link-fragmentation
Use the Multilink Interface ppp link-fragmentation command to configure the threshold byte size of
the packet, for Interleaving. Note: If the packet is > the set threshold, the packet will be split in half and
sent.
Syntax:
(config-int-mlink-{n})# ppp link-fragmentation number
Field
Definition
number
Range 320 - 1600, with a default of 1600 bytes.
Example: (config-int-mlink-1)# ppp link-fragmentation 600
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp on-demand
Use the Multilink Interface ppp on-demand command to enable on demand the feature. On demand
attempts to connect only when packets are sent. To disable PPP on demand, see no ppp on-demand
command on page 12-19.
Syntax:
(config-int-mlink-{n})# ppp on-demand
Example: (config-int-mlink-1)# ppp on-demand
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp password
Use the Multilink Interface ppp password command set the PPP password. To delete a PPP password,
see no ppp password command on page 12-19.
Syntax:
(config-int-mlink-{n})# ppp password password
Field
Definition
password
Enter the PPP password, with a maximum of 19 characters.
Example: (config-int-mlink-1)# ppp username test-user-pswrd
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
12-22
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Multilink Interface Mode
ppp qos-interleaving
Use the Multilink Interface ppp qos-interleaving command enable PPP Quality of Service
Interleaving. To disable PPP QoS Interleaving, see no ppp qos interleaving command on page 12-19.
Syntax:
(config-int-mlink-{n})# ppp qos-interleaving
Example: (config-int-mlink-1)# ppp qos-interleaving
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp restart-timer
Use the Multilink Interface ppp restart-timer command to configure the PPP restart timer.
Syntax:
(config-int-mlink-{n})# ppp restart-timer seconds
Field
Definition
enable
Enable IP TOS marking.
Example: (config-int-mlink-1)# ppp restart-timer 15
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp time-btwn-reconnect
Use the Multilink Interface ppp time-btwn-reconnect command configure the time between reconnect
attempts.
Syntax:
(config-int-mlink-{n})# ppp time-btwn-reconnect seconds
Field
Definition
seconds
Set the interval of time between reconnect attempts.
Range is 0 - 99999 seconds. Default is 30 seconds.
Example: (config-int-mlink-1)# ppp time-btwn-reconnect 15
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
12-23
Configuration - Multilink Interface Mode
ppp username
Use the Multilink Interface ppp username command set the PPP Login User Name. To delete a PPP
user, see no ppp qos interleaving command on page 12-19.
Syntax:
(config-int-mlink-{n})# ppp username username
Field
Definition
username
Enter the Username, with a maximum of 19 characters.
Example: (config-int-mlink-1)# ppp username test-user-name
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
schedule-availability
Use the Multilink Interface schedule-availability command to apply a schedule rule to this interface.
To delete a schedule, see no schedule-availability command on page 12-20.
Syntax:
(config-int-mlink-{n})# schedule-availability time-range
schedule-id
Field
Definition
schedule-id
Enter an existing schedule rule name. See time-range command on
page 4-62 to set the schedule-id
Example: (config-int-mlink-1)# schedule-availability time-range 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
shutdown
Use the Multilink Interface shutdown command to disable the multilink port. To set the Multilink port
up (In-Service), see no shutdown command on page 12-20.
Syntax:
(config-int-mlink-{n})# shutdown
Example: (config-int-mlink-1)# shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
12-24
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Multilink Interface Mode
sip-alg
Use the Multilink Interface sip-alg command to enable SIP ALG. To disable SIP ALG, see no sip-alg
command on page 12-20.
Syntax:
(config-int-mlink-{n})# sip-alg enable
Example: (config-int-mlink-1)# sip-alg enable
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
12-25
Configuration - Multilink Interface Mode
12-26
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
13
Configuration - Serial Interface Mode
The Serial Interface Configuration commands allow the user to configure the serial interface
parameters.
Enter this sub-group with the (config)# interface serial number command from the Configuration
mode.
The Serial Interface commands are represented by the (config-int-ser-{n})# prompt.
Note: Before configuring serial interface parameters, you must enable PPP encapsulation on the
interface using the encapsulation ppp command.
Serial Interface Commands
• description
• ip ospf disable
• no commands
• do
• ip ospf hello-interval
• ppp authentication
• encapsulation ppp
• ip ospf message-digest-key
• ppp encryption
• end
• ip ospf priority
• ppp exec-timeout
• exit
• ip ospf retransmit-interval
• ppp link-fragmentation
• firewall
• ip ospf transmit-delay
• ppp on-demand
• history
• ip primary-dns
• ppp password
• ip address
• ip rip
• ppp restart-timer
• ip default-route
• ip route
• ppp time-btwn-reconnect
• ip mtu
• ip route-mode
• ppp username
• ip ospf authentication
• ip secondary-dns
• schedule-availability
• ip ospf authentication-key
• metric
• shutdown
• ip ospf cost
• multilink-group
• sip-alg
• ip ospf dead-interval
Configuration - Serial Interface Mode
description
Use the Serial Interface description command to set the description for this serial interface.
Syntax:
(config-int-ser-{n})# description text
Field
Definition
text
Enter a description for the serial interface with a maximum of 64
characters.
Example: (config-int-ser-1)# description Serial1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
13-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Serial Interface Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
13-3
Configuration - Serial Interface Mode
encapsulation ppp
Use the Serial Interface encapsulation ppp command to enable PPP encapsulation. To disable
encapsulation, see no encapsulation ppp command on page 13-14.
Syntax:
(config-int-ser-{n})# encapsulation ppp
Example: (config-int-ser-1)# encapsulation ppp
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-int-ser-{n})# end
Example: (config-int-ser-1)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-int-ser-{n})# exit
Example: (config-int-ser-1)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
13-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Serial Interface Mode
firewall
Use the Serial Interface firewall command to enable the configured firewall. To delete a preference, see
no firewall command on page 13-14.
Syntax:
(config-int-ser-{n})# firewall enable
Example: (config-int-ser-1)# firewall enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-int-ser-{n})# history
Example: (config-int-ser-1)# history
encapsulation ppp
metric
ppp on-demand
ppp encryption 128-bit
ppp restart-timer 10
ppp time-btwn-reconnect 40
ip rip enable
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
13-5
Configuration - Serial Interface Mode
ip address
Use the Serial Interface ip address command to configure the IP address for the serial interface. To
remove an IP address, see no ip address command on page 13-15.
Syntax:
(config-int-ser-{n})# ip address {address mask mask|auto
|unnumbered} [secondary]
Field
Definition
address
Enter an IP address to assign to the port.
mask
Enter a subnet mask for the IP address.
auto
Uses IPCP to assign an IP address.
unnumbered
Treat this as an un-numbered interface, as per RFC 1812.
secondary
Optional parameter, defines the address to be a secondary IP address.
Example: (config-int-ser-1)# ip address 192.168.2.100 mask 255.255.255.0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip default-route
Use the Serial Interface ip default-route command to enable the default route. To disable the default
route, see no ip default-route command on page 13-15.
Syntax:
(config-int-ser-{n})# ip default-route enable
Example: (config-int-ser-1)# ip default-route enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip mtu
Use the Serial Interface ip mtu command to set the Maximum Transmission Unit. Sets the largest
packet size (bytes) the network will allow to transmit.
Syntax:
(config-int-ser-{n})# ip mtu {size|auto}
Field
Definition
size
Allows the user to set the Maximum Transmission Unit (MTU).
size = range of 576 to 1500 bytes.
auto
Auto sets the MTU at 1500 bytes.
Example: (config-int-ser-1)# ip mtu auto
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
13-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Serial Interface Mode
ip ospf authentication
Use the Serial Interface ip ospf authentication command to enable the authentication method (either
message-digest or simple authentication) for this serial interface. To remove the authentication type for
this interface set the parameter to null or see no ip ospf authentication command on page 13-15.
Note: If an optional parameter is not entered, the authentication method of simple authentication is
applied to the interface.
Syntax:
(config-int-ser-{n})# ip ospf authentication
[message-digest|null]
Field
Definition
message-digest
Optional parameter. Enables MD5 Authentication on the area.
null
Optional parameter. No authentication is used. Note: This is useful for
overriding password or message-digest authentication if configured
for an area.
Example: (config-int-ser-1)# ip ospf authentication message-digest
Note: The authentication key must be defined before this command is implemented.
Therefore if setting simple authentication:
Example: ip ospf authentication-key pass777
ip ospf authentication
Therefore if setting message-digest:
Example: ip ospf message-digest-key 1 md5 pass777
ip ospf authentication message-digest
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
13-7
Configuration - Serial Interface Mode
ip ospf authentication-key
Use the Serial Interface ip ospf authentication-key command to assign a password to be used by
neighboring routers, that are using OSPF’s simple password authentication.To remove a previously
assigned password, see no ip ospf authentication-key command on page 13-15.
Syntax:
(config-int-ser-{n})# ip ospf authentication-key password
Field
Definition
password
Enter a password, with up to 8 characters.
Example: (config-int-ser-1)# ip ospf authentication-key pass777
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf cost
Use the Serial Interface ip ospf cost command to define the cost of sending a packet on this serial
interface. To reset the path cost to the default setting of 0, see no ip ospf cost command on page 13-16.
Syntax:
(config-int-ser-{n})# ip ospf cost cost
Field
Definition
cost
Range is 1-65535, with a default of 0.
Example: (config-int-ser-1)# ip ospf cost 5
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf dead-interval
Use the Serial Interface ip ospf dead-interval command to define the interval of time that no hello
packets have been seen before neighbors declare the router down. To reset the interval of time to the
default setting of 40 seconds, see no ip ospf dead-interval command on page 13-16.
Syntax:
(config-int-ser-{n})# ip ospf dead-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 40.
Note: This value must be the same for all nodes on the network.
Example: (config-int-ser-1)# ip ospf dead-interval 50
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
13-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Serial Interface Mode
ip ospf disable
Use the Serial Interface ip ospf disable command to disable OSPF processing on this interface. To
enable OSPF on this interface, see no ip ospf disable command on page 13-16.
Syntax:
(config-int-ser-{n})# ip ospf disable all
Example: (config-int-ser-1)# ip ospf disable all
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf hello-interval
Use the Serial Interface ip ospf hello-interval command to define the interval of time between hello
packets sent on the interface. To reset the interval of time to the default setting of the path cost to the
default setting of 10 seconds, see no ip ospf hello-interval command on page 13-16.
Syntax:
(config-int-ser-{n})# ip ospf hello-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 10.
Note: This value must be the same for all nodes on the network.
Example: (config-int-ser-1)# ip ospf hello-interval 12
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf message-digest-key
Use the Serial Interface ip ospf message-digest-key command to enable OSPF MD5 (Message-Digest)
authentication. To remove an old MD5 key, see no ip ospf message-digest-key command on page 13-17.
Syntax:
(config-int-ser-{n})# ip ospf message-digest-key key-id md5 key
Field
Definition
key-id
Enter an ID for this key. Range is 1-255.
key
Enter a alphanumeric password, with up to 8 characters.
Example: (config-int-ser-1)# ip ospf message-digest-key 1 md5 key1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
13-9
Configuration - Serial Interface Mode
ip ospf priority
Use the Serial Interface ip ospf priority command to set the router priority, which determines the
designated router for this network. To restore the default setting of priority 1, see no ip ospf priority
command on page 13-17.
Syntax:
(config-int-ser-{n})# ip ospf priority priority
Field
Definition
priority
Enter an ID for this key. Range is 1-255.
Example: (config-int-ser-1)# ip ospf priority 2
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf retransmit-interval
Use the Serial Interface ip ospf retransmit-interval command to define the interval of time between
link state advertisement retransmissions for adjacencies belonging to the interface. To restore the
default value of 5 seconds, see no ip ospf retransmit-interval command on page 13-17.
Syntax:
(config-int-ser-{n})# ip ospf retransmit-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 5.
Example: (config-int-ser-1)# ip ospf retransmit-interval 10
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf transmit-delay
Use the Serial Interface ip ospf transmit-delay command to define the estimated time to transmit a link
state update packet on the interface. To restore the default value of 1 second, see no ip ospf transmitdelay command on page 13-17.
Syntax:
(config-int-ser-{n})# ip ospf transmit-delay seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 1.
Example: (config-int-ser-1)# ip ospf retransmit-interval 10
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
13-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Serial Interface Mode
ip primary-dns
Use the Serial Interface ip primary-dns command to configure the primary DNS. To delete a primary
DNS, see no ip primary-dns command on page 13-18.
Syntax:
(config-int-ser-{n})# ip primary-dns address
Field
Definition
address
Enter the IP address of the primary server.
Example: (config-int-ser-1)# ip primary-dns 192.168.1.200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip rip
ip rip enable
Use the Serial Interface ip rip enable command to enable RIP on this interface. To disable RIP, see
no ip rip command on page 13-18.
Syntax:
(config-int-ser-{n})# ip rip enable
Example: (config-int-ser-1)# ip rip enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip rip receive-version
Use the Serial Interface ip rip receive-version command to configure the RIP receive messages on
this interface.
Syntax:
(config-int-ser-{n})# ip rip receive-version {1|2|1or2|none}
Field
Definition
1|2|1or2
Receive RIP version 1
Receive RIP version 2
Receive RIP version 1 and 2.
none
Set RIP version to none.
Example: (config-int-ser-1)# ip rip receive-version none
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
13-11
Configuration - Serial Interface Mode
ip rip send-version
Use the Serial Interface ip rip send-version command to configure the send RIP messages on this
interface.
Syntax:
(config-int-ser-{n})# ip rip send-version {1|2-bcast|2-mcast
|none}
Field
Definition
1
Send RIP version 1.
2-bcast
Send RIP version 2 - Broadcast.
2-mcast
Send RIP version 2 - Multicast.
none
Set RIP version to none.
Example: (config-int-ser-1)# ip rip send-version 2-bcast
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip route
Use the Ethernet Interface ip route command to configure the IP routing on this interface. To delete a
route, see no ip route command on page 13-18.
Syntax:
(config-int-ser-{n})# ip route dest-ip-addr mask mask gateway
gateway metric metric
Field
Definition
dest-ip-addr
Enter the destination IP address.
mask
Enter the mask of the above address.
gateway
Enter the gateway IP address.
metric
Metric of IP network on this interface in Routing Table. Range is 0255, with a default is 10.
Example: (config-int-ser-1)# ip route 192.168.100.200 mask 255.255.255.0
gateway 192.168.100.254 mask 125
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
13-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Serial Interface Mode
ip route-mode
Use the Serial Interface ip route-mode command to configure the routing mode.
Syntax:
(config-int-ser-{n})# ip route-mode {napt|route}
Field
Definition
napt
Set to NAPT mode. Default.
NAPT is used if doing private IPs on the Ethernet side or if you want
to hide specific publics on the internal side.
route
Set to Route mode. Routing is used if public is visible on both sides.
Example: (config-int-ser-1)# ip route-mode napt
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip secondary-dns
Use the Serial Interface ip secondary-dns command to configure the secondary DNS. To delete a
secondary DNS address, see no ip secondary-dns command on page 13-18.
Syntax:
(config-int-ser-{n})# ip secondary-dns address
Field
Definition
address
Enter the IP address of the secondary Domain Name Server (DNS).
Example: (config-int-ser-1)# ip secondary-dns 192.168.1.200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
metric
Use the Serial Interface metric command to configure the metric of the IP network on this interface.
Syntax:
(config-int-ser-{n})# metric metric
Field
Definition
metric
Range is 0-255, with a default is 10.
Example: (config-int-ser-1)# metric 150
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
13-13
Configuration - Serial Interface Mode
multilink-group
Use the Serial Interface multilink-group command to configure a MLPPP group.
Syntax:
(config-int-ser-{n})# multilink-group group-number
Field
Definition
group-number
Enter multilink group.
Adit 3104, Adit 3200, Adit 3500: Value must be 1.
MSR: Range = 1-8.
Example: (config-int-ser-1)# multilink-group 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no commands
no encapsulation ppp
Use the Serial Interface no encapsulation ppp command to disable PPP encapsulation. To enable
encapsulation, see encapsulation ppp command on page 13-4.
Syntax:
(config-int-ser-{n})# no encapsulation ppp
Example: (config-int-ser-1)# no encapsulation ppp
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no firewall
Use the Serial Interface no firewall command to disable the configured firewall. To enable the
firewall, see firewall command on page 13-5.
Syntax:
(config-int-ser-{n})# no firewall
Example: (config-int-ser-1)# no firewall
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
13-14
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Serial Interface Mode
no ip address
Use the Serial Interface no ip address command to remove the IP address assigned to the serial
interface. To set the Serial IP address, see ip address command on page 13-6.
Syntax:
(config-int-ser-{n})# no ip address address
Field
Definition
address
Enter the IP address to remove.
Example: (config-int-ser-1)# no ip address 192.168.1.100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip default-route
Use the Serial Interface no ip default-route command to disable the default route. To set the default
IP address, see ip default-route command on page 13-6.
Syntax:
(config-int-ser-{n})# no ip default-route
Example: (config-int-ser-1)# no ip default-route
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf authentication
Use the Serial Interface no ip ospf authentication command to disable the authentication method
for this serial interface. To enable the authentication type for this interface see ip ospf authentication
command on page 13-7.
Syntax:
(config-int-ser-{n})# no ip ospf authentication
Example: (config-int-ser-{n})# no ip ospf authentication
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf authentication-key
Use the Serial Interface no ip ospf authentication-key command to remove a password to be used
by neighboring routers, that are using OSPF’s simple password authentication. To assign a
password, see ip ospf authentication-key command on page 13-8.
Syntax:
(config-int-ser-{n})# no ip ospf authentication
Example: (config-int-ser-1)# no ip ospf authentication-key
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
13-15
Configuration - Serial Interface Mode
no ip ospf cost
Use the Serial Interface no ip ospf cost command to reset the cost path to the default setting of 0.
To define the cost of sending a packet on this serial interface, see ip ospf cost command on
page 13-8.
Syntax:
(config-int-ser-{n})# no ip ospf cost
Example: (config-int-ser-1)# no ip ospf cost
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf dead-interval
Use the Serial Interface no ip ospf dead-interval command to reset the interval of time to the
default setting of 40 seconds. To define the interval of time that no hello packets have been seen
before neighbors declare the router down, see ip ospf dead-interval command on page 13-8.
Syntax:
(config-int-ser-{n})# no ip ospf dead-interval
Example: (config-int-ser-1)# no ip ospf dead-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf disable
Use the Serial Interface no ip ospf disable command to enable OSPF processing on this interface.
To disable OSPF on this interface, see ip ospf disable command on page 13-9.
Syntax:
(config-int-ser-{n})# ip ospf disable all
Example: (config-int-ser-1)# ip ospf disable all
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf hello-interval
Use the Serial Interface no ip ospf hello-interval command to reset the interval of time to the
default setting of the path cost to the default setting of 10 seconds. To define the interval of time
between hello packets that are sent on the interface, see ip ospf hello-interval command on
page 13-9.
Syntax:
(config-int-ser-{n})# no ip ospf hello-interval
Example: (config-int-ser-1)# no ip ospf hello-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
13-16
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Serial Interface Mode
no ip ospf message-digest-key
Use the Serial Interface no ip ospf message-digest-key command to remove an old MD5 key. To
enable OSPF MD5 (Message-Digest) authentication, see ip ospf message-digest-key command on
page 13-9.
Syntax:
(config-int-ser-{n})# no ip ospf message-digest-key key-id
Field
Definition
key-id
Enter an ID for this key. Range is 1-255.
Example: (config-int-ser-1)# no ip ospf message-digest-key 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf priority
Use the Serial Interface no ip ospf priority command to set the router priority to the default setting
of priority 1. To set the router priority, which determines the designated router for this network, see
ip ospf priority command on page 13-10.
Syntax:
(config-int-ser-{n})# no ip ospf priority
Example: (config-int-ser-1)# no ip ospf priority
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf retransmit-interval
Use the Serial Interface ip ospf retransmit-interval command to restore the default value of 5
seconds. To define the interval of time between link state advertisement retransmissions for
adjacencies belonging to the interface, see ip ospf retransmit-interval command on page 13-10.
Syntax:
(config-int-ser-{n})# no ip ospf retransmit-interval
Example: (config-int-ser-1)# no ip ospf retransmit-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf transmit-delay
Use the Serial Interface no ip ospf transmit-delay command to restore the default value of 1
second. To define the estimated time to transmit a link state update packet on the interface, see ip
ospf transmit-delay command on page 13-10.
Syntax:
(config-int-ser-{n})# no ip ospf transmit-delay
Example: (config-int-ser-1)# no ip ospf transmit-delay
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
13-17
Configuration - Serial Interface Mode
no ip primary-dns
Use the Serial Interface no primary-dns command to disable the primary DNS. To set the DNS
primary IP address, see ip primary-dns command on page 13-11.
Syntax:
(config-int-ser-{n})# no ip primary-dns
Example: (config-int-ser-1)# no ip primary-dns
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip rip
Use the Serial Interface no ip rip command to disable RIP on this interface. To enable RIP, see ip
rip command on page 13-11.
Syntax:
(config-int-ser-{n})# no ip rip
Example: (config-int-ser-1)# no ip rip
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip route
Use the Serial Interface no ip route command remove an IP route. To add a route, see ip route
command on page 13-12.
Syntax:
(config-int-ser-{n})# no ip route dest-ip-addr gateway
Field
Definition
dest-ip-addr
Enter destination IP address to remove.
gateway
Enter gateway IP address to remove.
Example: (config-int-ser-1)# no ip route 192.168.100.200
192.168.100.254
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip secondary-dns
Use the Serial Interface no secondary-dns command to disable the secondary DNS. To enable the
secondary DNS, see ip secondary-dns command on page 13-13.
Syntax:
(config-int-ser-{n})# no ip secondary-dns
Example: (config-int-ser-1)# no ip secondary-dns
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
13-18
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Serial Interface Mode
no ppp authentication
Use the Serial Interface no ppp authentication command disable PPP authentication. To enable
PPP authentication, see ppp authentication command on page 13-21.
Syntax:
(config-int-ser-{n})# no ppp authentication
Example: (config-int-ser-1)# no ppp authentication
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp encryption
Use the Serial Interface no ppp encryption command to disable PPP encryption. To enable PPP
encryption, see ppp encryption command on page 13-21.
Syntax:
(config-int-ser-{n})# no ppp encryption
Example: (config-int-ser-1)# no ppp encryption
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp on-demand
Use the Serial Interface no ppp on-demand command to disable PPP on-demand. To enable PPP
on demand, see ppp on-demand command on page 13-22.
Syntax:
(config-int-ser-{n})# no ppp on-demand
Example: (config-int-ser-1)# no ppp on-demand
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp password
Use the Serial Interface no ppp password command to remove the PPP password. To set the PPP
password, see ppp password command on page 13-22.
Syntax:
(config-int-ser-{n})# no ppp password
Example: (config-int-ser-1)# no ppp password
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
13-19
Configuration - Serial Interface Mode
no ppp username
Use the Serial Interface no ppp username command remove the PPP username. To set a PPP user,
see ppp username command on page 13-23.
Syntax:
(config-int-ser-{n})# no ppp username username
Example: (config-int-ser-1)# no ppp username test-user-name
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no schedule-availability
Use the Serial Interface no schedule-availability command to disable a schedule rule. To add a
rule, see schedule-availability command on page 13-24.
Syntax:
(config-int-ser-{n})# no schedule-availability
Example: (config-int-ser-1)# no schedule-availability
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no shutdown
Use the Serial Interface no shutdown command to set the serial interface up (In-Service). To set
the interface down (Out-of-Service), see shutdown command on page 13-24.
Syntax:
(config-int-ser-{n})# no shutdown
Example: (config-int-ser-1)# no shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no sip-alg
Use the Serial Interface no sip-alg command to disable SIP ALG on this interface. To enable SIP
ALG, see sip-alg command on page 13-24.
Syntax:
(config-int-ser-{n})# no sip-alg
Example: (config-int-ser-1)# no sip-alg
Supported Platforms: Adit 3104, Adit 3500, MSR
13-20
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Serial Interface Mode
ppp authentication
Use the Serial Interface ppp authentication command to configure the support of authentication types
for the password. To disable PPP authentication, see no ppp authentication command on page 13-19.
Syntax:
(config-int-ser-{n})# ppp authentication {chap|ms-chap|
ms-chapv2|pap}
Field
Definition
chap
Support Challenge Handshake Authentication (CHAP)
ms-chap
Support Microsoft CHAP (MS-CHAP).
ms-chapv2
Support Microsoft CHAP Version 2 (MS-CHAPv2).
pap
Support an unencrypted password.
Example: (config-int-ser-1)# ppp authentication chap
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp encryption
Use the Serial Interface ppp encryption command to configure the PPP encryption. To disable PPP
encryption, see no ppp encryption command on page 13-19.
Syntax:
(config-int-ser-{n})# ppp encryption {40-bit|128-bit}
Field
Definition
40-bit
Support Encryption (40 bit keys)
128-bit
Support Maximum Strength Encryption (128 bit keys)
Example: (config-int-ser-1)# ppp encryption 40-bit
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp exec-timeout
Use the Serial Interface ppp exec-timeout command to set the PPP maximum idle time before hangup.
Syntax:
(config-int-ser-{n})# ppp exec-timeout minutes
Field
Definition
minutes
Range is 0 - 99999 minutes.
Example: (config-int-ser-1)# ppp exec-timeout 150
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
13-21
Configuration - Serial Interface Mode
ppp link-fragmentation
Use the Serial Interface ppp link-fragmentation command to configure the threshold byte size of the
packet, for Interleaving. Note: If the packet is > the set threshold, the packet will be split in half and
sent.
Syntax:
(config-int-ser-{n})# ppp link-fragmentation number
Field
Definition
number
Range 320 - 1600, with a default of 1600 bytes.
Example: (config-int-ser-1)# ppp link-fragmentation 600
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp on-demand
Use the Serial Interface ppp on-demand command to enable on demand the feature. On demand
attempts to connect only when packets are sent. To disable PPP on demand, see no ppp encryption
command on page 13-19.
Syntax:
(config-int-ser-{n})# ppp on-demand
Example: (config-int-ser-1)# ppp on-demand
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp password
Use the Serial Interface ppp password command set the PPP password. To delete a PPP password, see
no ppp password command on page 13-19.
Syntax:
(config-int-ser-{n})# ppp password password
Field
Definition
password
Enter the PPP password, with a maximum of 19 characters.
Example: (config-int-ser-1)# ppp username test-user-pswrd
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
13-22
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Serial Interface Mode
ppp restart-timer
Use the Serial Interface ppp restart-timer command to configure the PPP restart timer.
Syntax:
(config-int-ser-{n})# ppp restart-timer seconds
Field
Definition
seconds
Range is 1 - 65535 seconds. Default is 3 seconds.
Example: (config-int-ser-1)# ppp restart-timer 15
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp time-btwn-reconnect
Use the Serial Interface ppp time-btwn-reconnect command configure the time between reconnect
attempts.
Syntax:
(config-int-ser-{n})# ppp time-btwn-reconnect seconds
Field
Definition
seconds
Set the interval of time between reconnect attempts.
Range is 0 - 99999 seconds. Default is 30 seconds.
Example: (config-int-ser-1)# ppp time-btwn-reconnect 15
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp username
Use the Serial Interface ppp username command set the PPP Login User Name. To delete a PPP user,
see no ppp username command on page 13-20.
Syntax:
(config-int-ser-{n})# ppp username username
Field
Definition
username
Enter the Username, with a maximum of 19 characters.
Example: (config-int-ser-1)# ppp username test-user-name
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
13-23
Configuration - Serial Interface Mode
schedule-availability
Use the Serial Interface schedule-availability command to apply a schedule rule to this interface. To
delete a schedule, see no schedule-availability command on page 13-20.
Syntax:
(config-int-ser-{n})# schedule-availability time-range
schedule-id
Field
Definition
schedule-id
Enter an existing schedule rule name. See time-range command on
page 4-62 to set the schedule-id
Example: (config-int-ser-1)# schedule-availability time-range 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
shutdown
Use the Serial Interface shutdown command to disable the serial interface. To set the serial interface
up (In-Service), see no shutdown command on page 13-20.
Syntax:
(config-int-ser-{n})# shutdown
Example: (config-int-ser-1)# shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
sip-alg
Use the Serial Interface sip-alg command to enable SIP ALG. To disable SIP ALG, see no sip-alg
command on page 13-20.
Syntax:
(config-int-ser-{n})# sip-alg enable
Example: (config-int-ser-1)# sip-alg enable
Supported Platforms: Adit 3104, Adit 3500, MSR
13-24
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
14
Configuration - IPSec Mode
The IPSecConfiguration commands allow the user to configure the VPN IPSec parameters.
Enter this sub-group with the (config)# ipsec vpn_ipsec command from the Configuration mode.
The IPSec commands are represented by the (config-ipsec-n)# prompt.
Note: First a connection must be created. See ipsec net-to-host command on page 4-23, or ipsec net-tonet command on page 4-24.
For an example of Configuring an IPSec Connection, see Example of IPSec Connection
Configuration command on page 14-21.
IPSec Commands
• aggressive-mode
• key
• authentication
• lifetime
• description
• local-subnet
• do
• max-retries
• dpd-delay
• mode
• dpd-enable
• net-type
• dpd-timeout
• netbios remote-brc-addr
• encryption
• no commands
• end
• reconnect
• exit
• rekey
• group
• remote-ip
• hash
• remote-subnet
• history
• schedule-availability
• ip route metric
• session-key
• ipsec-conn
• set-pfs
• ipsec-manual
• transform-set
Configuration - IPSec Mode
aggressive-mode
Use the IPSec aggressive-mode command to set to aggressive mode, instead of main mode. To set to
main mode, see no aggressive-mode command on page 14-12.
Syntax:
(config-ipsec {n})# aggressive-mode
Example: (config-ipsec-1)# aggressive-mode
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
authentication
Use the IPSec authentication command to specify a peer authentication method.
Syntax:
(config-ipsec {n})# authentication {pre-share shared-key|rsa-sig
rsa-signature|cert local-id peer-id}
Field
Definition
pre-shared
Specifies preshared keys as the authentication method.
shared-key- Enter the Pre-share key.
rsa-sig
Specifies RSA signatures as the authentication method.
rsa-signature - Enter the RSA signature.
cert
Set Certificate for local ID and Peer ID.
local-id - Enter the local ID.
peer-id - Enter the peer ID.
Example: (config-ipsec-1)# authentication pre-share mysecret
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
description
Use the IPSec description command to enter a description for the connection.
Syntax:
(config-ipsec {n})# description description
Field
Definition
description
Enter a description, with a maximum of 64 characters.
Example: (config-ipsec-1)# description Boulder VPN IPSec0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
14-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - IPSec Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
14-3
Configuration - IPSec Mode
dpd-delay
Use the IPSec dpd-delay command to set the Dead Period Detection delay. To set the DPD delay back
to the default settings, see no dpd-delay command on page 14-12.
Syntax:
(config-ipsec {n})# dpd-delay seconds
Field
Definition
seconds
Set the delay time in seconds. Range 1-3600 seconds, with a default of
60.
Example: (config-ipsec-1)# dpd-delay 200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
dpd-enable
Use the IPSec dpd-enable command to enable Dead Period Detection (DPD). To disable DPD, see no
dpd-enable command on page 14-12.
Syntax:
(config-ipsec {n})# dpd-enable
Example: (config-ipsec-1)# dpd-enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
dpd-timeout
Use the IPSec dpd-timeout command to set the Dead Period Detection (DPD) timeout period. To reset
DPD timeout to default setting, see no dpd-timeout command on page 14-12.
Syntax:
(config-ipsec {n})# dpd-timeout seconds
Field
Definition
seconds
Set the timeout period in seconds. Range 1-9999 seconds, with a
default of 120.
Example: (config-ipsec-1)# dpd-timeout
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
14-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - IPSec Mode
encryption
Use the IPSec encryption command to specify an encryption algorithm. To disable encryption, see no
group command on page 14-13.
Syntax:
(config-ipsec {n})# encryption {des|3des|aes|aes192|aes256}
Field
Definition
des
Set to 56-bit Data Encryption Standard (DES).
3des
Set to 168-bit DES. Default.
aes
Set 128-bit Advanced Encryption Standard (AES) as the encryption
algorithm.
aes192
Set 192-bit AES as the encryption algorithm.
aes256
Set 256-bit AES as the encryption algorithm.
Example: (config-ipsec-1)# encryption aes192
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-ipsec {n})# end
Example: (config-ipsec-1)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-ipsec {n})# exit
Example: (config-ipsec-1)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
14-5
Configuration - IPSec Mode
group
Use the IPSec group command to define the Diffie-Hellman (DH) group identifier for phase-1.
Note: More than one group can be enabled. To disable a DH identifier, see no group command on
page 14-13.
Syntax:
(config-ipsec {n})# group {1|2|5}
Field
Definition
1
Set to DH group 1 (768 bit).
2
Set to DH group 2 (1024 bit). Default is enabled.
5
Set to DH group 25 (1536 bit). Default is enabled.
Example: (config-ipsec-1)# group 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
hash
Use the IPSec hash command to specify a hash algorithm. To disable a hash algorithm, see no hash
command on page 14-14.
Syntax:
(config-ipsec {n})# hash {md5|sha}
Field
Definition
md5
Set to allow peers to use MD5.
sha
Set to allow peers to use SHA1. SHA = Secure Hash Algorithm.
Example: (config-ipsec-1)# hash md5
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
14-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - IPSec Mode
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-ipsec {n})# history
Example: (config-ipsec-1)# history
dpd
dpd-timeout 900
history
ip rip r
ip rip receive-version 1or2
ip rip enable
reconnect
ipsec-conn enable
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip route metric
Use the IPSec mode ip route metric command to define a number for the device metric.
Syntax:
(config-ipsec {n})# ip route metric metric
Field
Definition
metric
Enter a number for the device metric. Range is 0-255, with a default of
10.
Example: (config-ipsec-1)# ip route metric 25
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
14-7
Configuration - IPSec Mode
ipsec-conn
Use the IPSec mode ipsec-conn command to enable or disable an IPSec connection without removing
it.
Syntax:
(config-ipsec {n})# ipsec-conn {disable|enable}
Field
Definition
disable
Disable the IPSec connection.
enable
Enable the IPSec connection.
Example: (config-ipsec-1)# ipsec-conn enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ipsec-manual
Use the IPSec mode ipsec-manual command to select manual key exchange method. To enable
automatic key exchange method, see no ipsec-manual command on page 14-14.
Syntax:
(config-ipsec {n})# ipsec-manual
Example: (config-ipsec-1)# ipsec-manual
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
key
Use the IPSec key command to set the shared secret key.
Syntax:
(config-ipsec {n})# key key
Field
Definition
key
Enter a shared secret key, with a maximum of 30 characters.
Example: (config-ipsec-1)# key mysecret
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
14-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - IPSec Mode
lifetime
Use the IPSec mode lifetime command to set the connection lifetime.
Syntax:
(config-ipsec {n})# lifetime time seconds
Field
Definition
seconds
Set the connection lifetime. Range 1-86400 seconds, with a default of
86400.
Example: (config-ipsec-1)# lifetime time 70000
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
local-subnet
Use the IPSec mode local-subnet command to set the local subnet IP address.
Syntax:
(config-ipsec {n})# local-subnet {none|range {start-address
address end-address address}|single ip address|subnet ip
address}
Field
Definition
none
No IP address.
range
Enter an IP address range.
start-address - Enter the start IP address of the range.
end-address - Enter the end IP address of the range.
single ip
Enter a single IP address.
subnet ip
Enter a subnet IP address.
Example: (config-ipsec-1)# local-subnet range start-address 192.168.1.1
end-address 192.168.1.10
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
14-9
Configuration - IPSec Mode
max-retries
Use the IPSec mode max-retries command to set a maximum number of negotiation attempts.
Syntax:
(config-ipsec {n})# max-retries number
Field
Definition
number
Valid values: 0, 1, 2, 3, 4, 8, 16, 24, 32, 48, 64. Default is 3.
0 = infinite negotiation attempts.
Example: (config-ipsec-1)# max-retries 16
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
mode
Use the IPSec mode mode command to modify an IPSec security association mode. Note: If a router
requests tunnel mode, only tunnel mode can be negotiated between the peers. However, if transport
mode is requested, either transport or tunnel mode can be negotiated.
Syntax:
(config-ipsec {n})# mode {transport|tunnel}
Field
Definition
transport
Transport Mode - only the payload of the original IP packet is
encrypted and/or authenticated. The protected inside addresses will
appear in the original IP headers.
Tunnel Mode - The original IP packet is encrypted and/or
authenticated and is encapsulated in a new IP packet. Only the peer
outside addresses are seen, the protected inside addresses are hidden
from view. Default.
tunnel
Example: (config-ipsec-1)# mode transport
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
14-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - IPSec Mode
net-type
Use the IPSec mode net-type command to define the network type.
Syntax:
(config-ipsec {n})# network-type {dmz|lan|wan}
Field
Definition
dmz
lan
wan
Demilitarized Zone.
Local Area Network.
Wide Area Network.
Example: (config-ipsec-1)# net-type lan
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
netbios remote-brc-addr
Use the IPSec netbios remote-brc-addr command to set the remote broadcast address for NetBIOS.
Syntax:
(config-ipsec-{n})# netbios remote-brc-addr address
Field
Definition
address
Enter the remote broadcast address.
Example: (config-ipsec-1)# netbios remote-brc-addr 192.168.1.200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
14-11
Configuration - IPSec Mode
no commands
no aggressive-mode
Use the IPSec mode no aggressive-mode command to set to main mode, instead of aggressive mode.
To set to aggressive mode, see aggressive-mode command on page 14-2.
Syntax:
(config-ipsec {n})# no aggressive-mode
Example: (config-ipsec-1)# no aggressive-mode
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no dpd-delay
Use the IPSec no dpd-delay command to reset the Dead Period Detection (DPD) delay back to the
default settings. To set the DPD delay, see dpd-delay command on page 14-4.
Syntax:
(config-ipsec-{n})# no dpd-delay
Example: (config-ipsec-1)# no dpd-delay
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no dpd-enable
Use the IPSec no dpd-enable command to disable Dead Period Detection (DPD). To enable DPD, see
dpd-enable command on page 14-4.
Syntax:
(config-ipsec-{n})# no dpd-enable
Example: (config-ipsec-1)# no dpd-enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no dpd-timeout
Use the IPSec no dpd-timeout command to set the Dead Period Detection (DPD) timeout to the default
setting. To set DPD timeout, see dpd-timeout command on page 14-4.
Syntax:
(config-ipsec-{n})# no dpd-timeout
Example: (config-ipsec-1)# no dpd-timeout
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
14-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - IPSec Mode
no encryption
Use the IPSec no encryption command to disable encryption. To configure encryption, see encryption
command on page 14-5.
Syntax:
(config-ipsec-{n})# no encryption {des|3des|aes|aes192| aes256}
Field
Definition
des
Disable 56-bit Data Encryption Standard (DES).
3des
Disable 168-bit DES. Default.
aes
Disable 128-bit Advanced Encryption Standard (AES) as the
encryption algorithm.
aes192
Disable 192-bit AES as the encryption algorithm.
aes256
Disable 256-bit AES as the encryption algorithm.
Example: (config-ipsec-1)# no encryption aes
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no group
Use the IPSec no group command to disable a Diffie-Hellman (DH) group identifier. To set a DH group
identifier, see group command on page 14-6.
Syntax:
(config-ipsec-{n})# no group {1|2|5}
Field
Definition
1
Disable DH group 1 (768 bit).
2
Disable DH group 2 (1024 bit). Default is enabled.
5
Disable DH group 25 (1536 bit). Default is enabled.
Example: (config-ipsec-1)# no group 2
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
14-13
Configuration - IPSec Mode
no hash
Use the IPSec no hash command to disable a hash algorithm. To set a hash algorithm, see hash
command on page 14-6.
Syntax:
(config-ipsec-{n})# no hash {md5|sha}
Field
Definition
md5
Disable the MD5 algorithm.
sha
Disable SHA1. SHA = Secure Hash Algorithm.
Example: (config-ipsec-1)# no hash md5
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip rip
Use the IPSec no ip rip command to disable RIP.
Syntax:
(config-ipsec-{n})# no ip rip
Example: (config-ipsec-1)# no ip rip
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ipsec-manual
Use the IPSec no ipsec-manual command to enable automatic key exchange method. To enable manual
key exchange method, see ipsec-manual command on page 14-8.
Syntax:
(config-ipsec-{n})# no ipsec-manual
Example: (config-ipsec-1)# no ipsec-manual
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no netbios
Use the IPSec no netbios command to disable routing of NetBIOS broadcasts. To enable NetBIOS
broadcasts, see netbios remote-brc-addr command on page 14-11.
Syntax:
(config-ipsec-{n})# no netbios
Example: (config-ipsec-1)# no netbios
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
14-14
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - IPSec Mode
no reconnect
Use the IPSec no reconnect command to disable automatic reconnection. To enable reconnection, see
reconnect command on page 14-17.
Syntax:
(config-ipsec-{n})# no reconnect
Example: (config-ipsec-1)# no reconnect
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no schedule-availability
Use the IPSec no schedule-availability command to set schedule availability to the default value. To
set a schedule rule, see schedule-availability command on page 14-18.
Syntax:
(config-ipsec-{n})# no schedule-availability
Example: (config-ipsec-1)# no schedule-availability
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no set-pfs
Use the IPSec no set-pfs command to disable Perfect Forward Secrecy. To enable PFS, see set-pfs
command on page 14-19.
Syntax:
(config-ipsec-{n})# no set-pfs
Example: (config-ipsec-1)# no set-pfs
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
14-15
Configuration - IPSec Mode
no transform-set
Use the IPSec no transform-set command to disable Perfect Forward Secrecy. To enable PFS, see
transform-set command on page 14-20.
Syntax:
(config-ipsec-{n})# no transform-set {ah-md5|ah-sha|esp-3des|
esp-aes|esp-aes192|esp-aes256|esp-des|esp-md5|esp-null|esp-sha
|ipcomp}
Field
Definition
ah-md5
Authentication Header transform using MD5 authentication. Default.
ah-sha
Authentication Header transform using Secure Hash Algorithm
(SHA1) authentication. Default.
esp-aes
Encapsulating Security Payload (ESP) encryption transform using
Advanced Encryption Standard (AES) 128-bit encryption.
esp-aes192
Encapsulating Security Payload (ESP) encryption transform using
Advanced Encryption Standard (AES) 128-bit encryption.
esp-aes256
Encapsulating Security Payload (ESP) encryption transform using
Advanced Encryption Standard (AES) 256-bit encryption.
esp-des
Encapsulating Security Payload (ESP) encryption transform using
Data Encryption Standard (DES) 56-bit encryption.
esp-3des
Encapsulating Security Payload (ESP) encryption transform using
Data Encryption Standard (DES) 168-bit encryption.
esp-null
Encapsulating Security Payload (ESP) encryption transform using no
encryption.
esp-md5
Encapsulating Security Payload (ESP) encryption transform using
Message-Digest Algorithm 5 (MD5) authentication. Default.
esp-sha
Encapsulating Security Payload (ESP) encryption transform using
Secure Hash Algorithm (SHA1) authentication. Default.
ipcomp
IP Payload Compression Protocol (IPComp) compression.
Example: (config-ipsec-1)# no transform-set esp-md5
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
14-16
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - IPSec Mode
reconnect
Use the IPSec reconnect command to enable the automatic reconnection option. To disable
reconnection, see no reconnect command on page 14-15.
Syntax:
(config-ipsec-{n})# reconnect
Example: (config-ipsec-1)# reconnect
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
rekey
Use the IPSec rekey command to set the rekey lifetime, rekey margin and rekey fuzz percent.
Syntax:
(config-ipsec-{n})# rekey lifetime seconds margin margin percent
percent
Field
Definition
seconds
Set the connection rekey lifetime. Range is 1-28800 seconds, with a
default of 3600.
margin
Set the rekey margin number. Range is 1-540, with a default of 540.
percent
Set the rekey fuzz percent. Range 1-200, with a default of 100.
Example: (config-ipsec-1)# rekey lifetime 3 margin 500 percent 200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
remote-ip
Use the IPSec remote-ip command to modify a remote tunnel endpoint address.
Syntax:
Syntax:
(config-ipsec-{n})# remote-ip address
Field
Definition
address
Enter a remote IP address.
(config-ipsec-1)# remote-ip 10.10.2.10
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
14-17
Configuration - IPSec Mode
remote-subnet
Use the IPSec remote-subnet command to set the remote subnet IP address.
Syntax:
Syntax:
(config-ipsec-{n})# remote-subnet {none|range {start-address
address end-address address}|single ip address|subnet ip
address}
Field
Definition
none
No IP address.
range
Enter an IP address range.
start-address - Enter the start IP address of the range.
end-address - Enter the end IP address of the range.
single ip
Enter a single IP address.
subnet ip
Enter a subnet IP address.
(config-ipsec-1)# remote-subnet single ip 10.10.2.200 mask
255.255.0.0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
schedule-availability
Use the IPSec schedule-availability command to apply a schedule rule to this connection. To reset to
the default value of "always", see no schedule-availability command on page 14-15.
Syntax:
(config-ipsec-{n})# schedule-availability rule-id
Field
Definition
rule-id
Enter an existing schedule
Example: (config-ipsec-1)# schedule-availability rule1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
14-18
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - IPSec Mode
session-key
Use the IPSec session-key command to specify the parameters needed during manual key exchange
(ipsec-manual).
Syntax:
(config-ipsec-{n})# session-key {inbound|outbound} ah spi
authentication [md5|sha] hex-key-data
Field
Definition
inbound
Set the inbound (local) IPSec key.
outbound
Set the outbound (remote) IPSec key.
ah spi
Set the Authentication Header Security Parameter Index. 100-FFF
md5
Set authentication to MD5.
sha
Set authentication to Secure Hash Algorithm.
hex-key-data
MD5 or SHA authentication key in hex. String length must be 40.
Example: (config-ipsec-1)# session-key outbound ah 256 authentication md5
0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
set-pfs
Use the IPSec set-pfs command to enable Perfect Forward Secrecy.
Syntax:
(config-ipsec-{n})# set-pfs {1|2|5|phase1}
Field
Definition
1
Use DH group 1 (768 bit).
2
Use DH group 2 (1024 bit).
5
Use DH group 25 (1536 bit).
phase1
Use the same settings as the Phase 1 group settings.
Example: (config-ipsec-1)# set-pfs phase1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
14-19
Configuration - IPSec Mode
transform-set
Use the IPSec transform-set command to set the allowable encryption methods, authentication
protocols and to enable compression during automatic key exchange. To disable encryption/
authentication/compression, see no transform-set command on page 14-16.
Syntax:
(config-ipsec-{n})# transform-set {ah-md5|ah-sha|esp-3des| espaes|esp-aes192|esp-aes256|esp-des|esp-md5|esp-null|esp-sha
|ipcomp}
Field
Definition
ah-md5
Authentication Header transform using MD5 authentication. Default.
ah-sha
Authentication Header transform using Secure Hash Algorithm
(SHA1) authentication. Default.
esp-aes
Encapsulating Security Payload (ESP) encryption transform using
Advanced Encryption Standard (AES) 128-bit encryption.
esp-aes192
Encapsulating Security Payload (ESP) encryption transform using
Advanced Encryption Standard (AES) 128-bit encryption.
esp-aes256
Encapsulating Security Payload (ESP) encryption transform using
Advanced Encryption Standard (AES) 256-bit encryption.
esp-des
Encapsulating Security Payload (ESP) encryption transform using
Data Encryption Standard (DES) 56-bit encryption.
esp-3des
Encapsulating Security Payload (ESP) encryption transform using
Data Encryption Standard (DES) 168-bit encryption.
esp-null
Encapsulating Security Payload (ESP) encryption transform using no
encryption.
esp-md5
Encapsulating Security Payload (ESP) encryption transform using
Message-Digest Algorithm 5 (MD5) authentication. Default.
esp-sha
Encapsulating Security Payload (ESP) encryption transform using
Secure Hash Algorithm (SHA1) authentication. Default.
ipcomp
IP Payload Compression Protocol (IPComp) compression.
Example: (config-ipsec-1)# transform-set esp-aes
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
14-20
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - IPSec Mode
Example of IPSec Connection Configuration
Example of IPSec Connection Configuration
Adit 3104(config)#ipsec VPN_IPSEC 0
Adit 3104(config-ipsec-0)#dev-name VPNIPSec0
Adit 3104(config-ipsec-0)#net-type WAN
Adit 3104(config-ipsec-0)#aggressive-mode
Adit 3104(config-ipsec-0)#authentication pre-share ocho
Adit 3104(config-ipsec-0)#no encryption des
Adit 3104(config-ipsec-0)#no encryption 3des
Adit 3104(config-ipsec-0)#no encryption aes
Adit 3104(config-ipsec-0)#encryption aes192
Adit 3104(config-ipsec-0)#no encryption aes256
Adit 3104(config-ipsec-0)#group 1
Adit 3104(config-ipsec-0)#no group 2
Adit 3104(config-ipsec-0)#no group 5
Adit 3104(config-ipsec-0)#hash md5
Adit 3104(config-ipsec-0)#no hash sha
Adit 3104(config-ipsec-0)#no ipsec-manual
Adit 3104(config-ipsec-0)#lifetime time 3601
Adit 3104(config-ipsec-0)#local-subnet single ip 11.0.0.1
Adit 3104(config-ipsec-0)#remote-ip 172.15.16.2
Adit 3104(config-ipsec-0)#
Adit 3104(config-ipsec-0)#dpd-enable
Adit 3104(config-ipsec-0)#dpd-delay 70
Adit 3104(config-ipsec-0)#dpd-timeout 130
Adit 3104(config-ipsec-0)#ip route metric 11
Adit 3104(config-ipsec-0)#no ip default-route
Adit 3104(config-ipsec-0)#no ip rip
Adit 3104(config-ipsec-0)#
Adit 3104(config-ipsec-0)#remote-subnet single ip 31.0.0.1
Adit 3104(config-ipsec-0)#max-retries 4
Adit 3104(config-ipsec-0)#mode tunneling
Adit 3104(config-ipsec-0)#netbios remote-brc-addr 255.255.255.255
Adit 3104(config-ipsec-0)#reconnect
Adit 3104(config-ipsec-0)#rekey lifetime 3601 margin 539 percent 101
Adit 3104(config-ipsec-0)#no schedule-availability
Adit 3104(config-ipsec-0)#set-pfs 2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
14-21
Configuration - IPSec Mode
Example of IPSec Connection Configuration
Adit 3104(config-ipsec-0)#transform-set esp-null
Adit 3104(config-ipsec-0)#transform-set esp-des
Adit 3104(config-ipsec-0)#transform-set esp-3des
Adit 3104(config-ipsec-0)#transform-set esp-aes
Adit 3104(config-ipsec-0)#transform-set esp-aes192
Adit 3104(config-ipsec-0)#transform-set esp-aes256
Adit 3104(config-ipsec-0)#transform-set esp-md5
Adit 3104(config-ipsec-0)#transform-set esp-sha
Adit 3104(config-ipsec-0)#transform-set ah-md5
Adit 3104(config-ipsec-0)#transform-set ah-sha
Adit 3104(config-ipsec-0)#no transform-set ipcomp
Adit 3104(config-ipsec-0)#
14-22
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
15
Configuration - L2TPC Mode
The L2TPC Configuration commands allow the user to configure the VPN Layer 2 Tunneling Protocol
Connection (L2TPC) parameters.
Enter this sub-group with the (config)# l2tpc command from the Configuration mode.
The VPN L2TPC commands are represented by the (config-l2tpc-1)# prompt.
L2TPC Commands
• do
• ip primary-dns
• end
• ip rip
• exit
• ip route
• firewall
• ip route-mode
• history
• ip secondary-dns
• host-ip
• local-secret
• ip address
• metric
• ip default-route
• no commands
• ip mtu
• ppp authentication
• ip ospf authentication
• ppp encryption
• ip ospf authentication-key
• ppp exec-timeout
• ip ospf cost
• ppp on-demand
• ip ospf dead-interval
• ppp password
• ip ospf disable
• ppp restart-timer
• ip ospf hello-interval
• ppp time-btwn-reconnect
• ip ospf message-digest-key
• ppp username
• ip ospf priority
• schedule-availability
• ip ospf retransmit-interval
• shutdown
• ip ospf transmit-delay
• sip-alg
Configuration - L2TPC Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
15-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - L2TPC Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-l2tpc-{n})# end
Example: (config-l2tpc-1)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-l2tpc-{n})# exit
Example: (config-l2tpc-1)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
firewall
Use the L2TPC firewall command to enable the configured firewall. To delete a preference, see no
firewall command on page 15-13.
Syntax:
(config-l2tpc-{n})# firewall enable
Example: (config-l2tpc-1)# firewall enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
15-3
Configuration - L2TPC Mode
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-l2tpc-{n})# history
Example: (config-l2tpc-1)# history
firewall enable
exit
host-ip 192.168.1.10
ip default-route enable
ip rip enable
ip rip send-version none
ip primary-dns 192.168.2.10
ip route 192.168.1.160
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
host-ip
Use the L2TPC host-ip command to configure the IP address for the host.
Syntax:
(config-l2tpc-{n})# host-ip {address}
Field
Definition
address
Enter the IP address for the host.
Example: (config-l2tpc-1)# host-ip 192.168.2.101
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
15-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - L2TPC Mode
ip address
Use the L2TPC ip address command to configure the IP address for the port. To remove an IP address,
see no ip address command on page 15-13.
Syntax:
(config-l2tpc-{n})# ip address {address mask mask|auto
|unnumbered} [secondary]
Field
Definition
address
Enter an IP address to assign to the port.
mask
Enter a subnet mask for the IP address.
auto
Uses IPCP to assign an IP address.
unnumbered
Treat this as an un-numbered interface, as per RFC 1812.
secondary
Optional parameter, defines the address to be a secondary IP address.
Example: (config-l2tpc-1)# ip address 192.168.2.100 mask 255.255.255.0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip default-route
Use the L2TPC ip default-route command to enable the default route. To disable the default route, see
no ip default-route command on page 15-14.
Syntax:
(config-l2tpc-{n})# ip default-route enable
Example: (config-l2tpc-1)# ip default-route enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip mtu
Use the L2TPC ip mtu command to set the Maximum Transmission Unit. Sets the largest packet size
(bytes) the network will allow to transmit.
Syntax:
(config-l2tpc-{n})# ip mtu {size|auto}
Field
Definition
size
Allows the user to set the Maximum Transmission Unit (MTU).
size = Range of 576 to 1500 bytes.
auto
Auto sets the MTU at 1500 bytes.
Example: (config-l2tpc-1)# ip mtu auto
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
15-5
Configuration - L2TPC Mode
ip ospf authentication
Use the L2TPC ip ospf authentication command to enable the authentication method (either messagedigest or simple authentication) for this interface. To remove the authentication type for this interface
set the parameter to null or see no ip ospf authentication command on page 15-14.
Note: If an optional parameter is not entered, the authentication method of simple authentication is
applied to the interface.
Syntax:
(config-l2tpc-{n})# ip ospf authentication [message-digest|
null]
Field
Definition
message-digest
Optional parameter. Enables MD5 Authentication on the area.
null
Optional parameter. No authentication is used. Note: This is useful for
overriding password or message-digest authentication if configured
for an area.
Example: (config-l2tpc-1)# ip ospf authentication message-digest
Note: The authentication key must be defined before this command is implemented.
Therefore if setting simple authentication:
Example: ip ospf authentication-key pass777
ip ospf authentication
Therefore if setting message-digest:
Example: ip ospf message-digest-key 1 md5 pass777
ip ospf authentication message-digest
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
15-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - L2TPC Mode
ip ospf authentication-key
Use the L2TPC ip ospf authentication-key command to assign a password to be used by neighboring
routers, that are using OSPF’s simple password authentication.To remove a previously assigned
password, see no ip ospf authentication-key command on page 15-14.
Syntax:
(config-l2tpc-{n})# ip ospf authentication-key password
Field
Definition
password
Enter a password, with up to 8 characters.
Example: (config-l2tpc-1)# ip ospf authentication-key pass777
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf cost
Use the L2TPC ip ospf cost command to define the cost of sending a packet on this serial interface. To
reset the path cost to the default setting of 0, see no ip ospf cost command on page 15-14.
Syntax:
(config-l2tpc-{n})# ip ospf cost cost
Field
Definition
cost
Range is 1-65535, with a default of 0.
Example: (config-l2tpc-1)# ip ospf cost 5
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf dead-interval
Use the L2TPC ip ospf dead-interval command to define the interval of time that no hello packets have
been seen before neighbors declare the router down. To reset the interval of time to the default setting
of 40 seconds, see no ip ospf dead-interval command on page 15-15.
Syntax:
(config-l2tpc-{n})# ip ospf dead-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 40.
Note: This value must be the same for all nodes on the network.
Example: (config-l2tpc-1)# ip ospf dead-interval 50
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
15-7
Configuration - L2TPC Mode
ip ospf disable
Use the L2TPC ip ospf disable command to disable OSPF processing on this interface. To enable OSPF
on this interface, see no ip ospf disable command on page 15-15.
Syntax:
(config-l2tpc-{n})# ip ospf disable all
Example: (config-l2tpc-1)# ip ospf disable all
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf hello-interval
Use the L2TPC ip ospf hello-interval command to define the interval of time between hello packets
sent on the interface. To reset the interval of time to the default setting of the path cost to the default
setting of 10 seconds, see no ip ospf hello-interval command on page 15-15.
Syntax:
(config-l2tpc-{n})# ip ospf hello-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 10.
Note: This value must be the same for all nodes on the network.
Example: (config-l2tpc-1)# ip ospf hello-interval 12
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf message-digest-key
Use the L2TPC ip ospf message-digest-key command to enable OSPF MD5 (Message-Digest)
authentication. To remove an old MD5 key, see no ip ospf message-digest-key command on page 15-16.
Syntax:
(config-l2tpc-{n})# ip ospf message-digest-key key-id md5 key
Field
Definition
key-id
Enter an ID for this key. Range is 1-255.
key
Enter a alphanumeric password, with up to 8 characters.
Example: (config-l2tpc-1)# ip ospf message-digest-key 1 md5 key1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
15-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - L2TPC Mode
ip ospf priority
Use the L2TPC ip ospf priority command to set the router priority, which determines the designated
router for this network. To restore the default setting of priority 1, see no ip ospf priority command on
page 15-16.
Syntax:
(config-l2tpc-{n})# ip ospf priority priority
Field
Definition
priority
Enter an ID for this key. Range is 0-255.
Example: (config-l2tpc-1)# ip ospf priority 2
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf retransmit-interval
Use the L2TPC ip ospf retransmit-interval command to define the interval of time between link state
advertisement retransmissions for adjacencies belonging to the interface. To restore the default value of
5 seconds, see no ip ospf retransmit-interval command on page 15-16.
Syntax:
(config-l2tpc-{n})# ip ospf retransmit-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 5.
Example: (config-l2tpc-1)# ip ospf retransmit-interval 10
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf transmit-delay
Use the L2TPC ip ospf transmit-delay command to define the estimated time to transmit a link state
update packet on the interface. To restore the default value of 1 second, see no ip ospf transmit-delay
command on page 15-17.
Syntax:
(config-l2tpc-{n})# ip ospf transmit-delay seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 1.
Example: (config-l2tpc-1)# ip ospf transmit-delay 10
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
15-9
Configuration - L2TPC Mode
ip primary-dns
Use the L2TPC ip primary-dns command to configure the primary DNS. To delete a primary DNS,
see no ip primary-dns command on page 15-17.
Syntax:
(config-l2tpc-{n})# ip primary-dns address
Field
Definition
address
Enter the IP address of the primary server.
Example: (config-l2tpc-1)# ip primary-dns 192.168.2.100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip rip
ip rip enable
Use the L2TPC ip rip enable command to enable RIP on this interface. To disable RIP, see no ip
rip command on page 15-17.
Syntax:
(config-l2tpc-{n})# ip rip enable
Example: (config-l2tpc-1)# ip rip enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip rip receive-version
Use the L2TPC ip rip receive-version command to configure the RIP receive messages on this
interface.
Syntax:
(config-l2tpc-{n})# ip rip receive-version {1|2|1or2|none}
Field
Definition
1|2|1or2
Receive RIP version 1
Receive RIP version 2
Receive RIP version 1 and 2.
none
Set RIP version to none.
Example: (config-l2tpc-1)# ip rip receive-version none
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
15-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - L2TPC Mode
ip rip send-version
Use the L2TPC ip rip send-version command to configure the send RIP messages on this interface.
Syntax:
(config-l2tpc-{n})# ip rip send-version {1|2-bcast|2-mcast
|none}
Field
Definition
1
Send RIP version 1.
2-bcast
Send RIP version 2 - Broadcast.
2-mcast
Send RIP version 2 - Multicast.
none
Set RIP version to none.
Example: (config-l2tpc-1)# ip rip send-version 2-bcast
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip route
Use the L2TPC ip route command to configure the IP routing on this interface. To delete a route, see
no ip route command on page 15-17.
Syntax:
(config-l2tpc-{n})# ip route dest-ip-addr mask mask gateway
gateway metric metric
Field
Definition
dest-ip-addr
Enter the destination IP address.
mask
Enter the mask of the above address.
gateway
Enter the gateway IP address.
metric
Metric of IP network on this interface in Adit 3500 Routing Table.
Range is 0-255, with a default is 10.
Example: (config-l2tpc-1)# ip route 192.168.100.200 mask 255.255.255.0
gateway 192.168.100.254 mask 125
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
15-11
Configuration - L2TPC Mode
ip route-mode
Use the L2TPC ip route-mode command to configure the routing mode.
Syntax:
(config-l2tpc-{n})# ip route-mode {napt|route}
Field
Definition
napt
Set to NAPT mode. Default.
NAPT is used if doing private IPs on the Ethernet side or if you want
to hide specific publics on the internal side.
route
Set to Route mode. Routing is used if public is visible on both sides.
Example: (config-l2tpc-1)# ip route-mode napt
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip secondary-dns
Use the L2TPC ip secondary-dns command to configure the secondary DNS. To delete a secondary
DNS address, see no ip secondary-dns command on page 15-18.
Syntax:
(config-l2tpc-{n})# ip secondary-dns address
Field
Definition
address
Enter the IP address of the secondary Domain Name Server (DNS).
Example: (config-l2tpc-1)# ip secondary-dns 192.168.1.200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
local-secret
Use the L2TPC local-secret command to configure the local secret password on this interface.
Syntax:
(config-l2tpc-{n})# local-secret {shared-secret}
Field
Definition
shared-secret
Enter a secret password used to authenticate L2TP connection.
Maximum number of characters is 96.
Example: (config-l2tpc-1)# local-secret secretpassword
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
15-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - L2TPC Mode
metric
Use the L2TPC metric command to configure the Metric of the IP network on this interface.
Syntax:
(config-l2tpc-{n})# metric metric
Field
Definition
metric
Range is 0-255, with a default is 10.
Example: (config-l2tpc-1)# metric 150
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no commands
no firewall
Use the L2TPC no firewall command to disable the configured firewall. To enable the firewall, see
firewall command on page 15-3.
Syntax:
(config-l2tpc-{n})# no firewall
Example: (config-l2tpc-1)# no firewall
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip address
Use the L2TPC no ip address command to remove the IP address assigned to the port. To set the
Serial IP address, see ip address command on page 15-5.
Syntax:
(config-l2tpc-{n})# no ip address address
Field
Definition
address
Enter the IP address to remove.
Example: (config-l2tpc-1)# no ip address 192.168.1.100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
15-13
Configuration - L2TPC Mode
no ip default-route
Use the L2TPC no ip default-route command to disable the default route. To set the default IP
address, see ip default-route command on page 15-5.
Syntax:
(config-l2tpc-{n})# no ip default-route
Example: (config-l2tpc-1)# no ip default-route
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf authentication
Use the L2TPC no ip ospf authentication command to disable the authentication method for this
serial interface. To enable the authentication type for this interface see ip ospf authentication
command on page 15-6.
Syntax:
(config-l2tpc-{n})# no ip ospf authentication
Example: (config-l2tpc-1)# no ip ospf authentication
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf authentication-key
Use the L2TPC no ip ospf authentication-key command to remove a password to be used by
neighboring routers, that are using OSPF’s simple password authentication.To assign a password,
see ip ospf authentication-key command on page 15-7.
Syntax:
(config-l2tpc-{n})# no ip ospf authentication-key
Example: (config-l2tpc-1)# no ip ospf authentication-key
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf cost
Use the L2TPC no ip ospf cost command to reset the cost path to the default setting of 0. To define
the cost of sending a packet on this serial interface, see ip ospf cost command on page 15-7.
Syntax:
(config-l2tpc-{n})# no ip ospf cost
Example: (config-l2tpc-1)# no ip ospf cost
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
15-14
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - L2TPC Mode
no ip ospf dead-interval
Use the L2TPC no ip ospf dead-interval command to reset the interval of time to the default setting
of 40 seconds. To define the interval of time that no hello packets have been seen before neighbors
declare the router down, see ip ospf dead-interval command on page 15-7.
Syntax:
(config-l2tpc-{n})# no ip ospf dead-interval
Example: (config-l2tpc-1)# no ip ospf dead-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf disable
Use the L2TPC no ip ospf disable command to enable OSPF processing on this interface. To
disable OSPF on this interface, see ip ospf disable command on page 15-8.
Syntax:
(config-l2tpc-{n})# ip ospf disable all
Example: (config-l2tpc-1)# ip ospf disable all
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf hello-interval
Use the L2TPC no ip ospf hello-interval command to reset the interval of time to the default setting
of the path cost to the default setting of 10 seconds. To define the interval of time between hello
packets sent on the interface, see ip ospf hello-interval command on page 15-8.
Syntax:
(config-l2tpc-{n})# no ip ospf hello-interval
Example: (config-l2tpc-1)# no ip ospf hello-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
15-15
Configuration - L2TPC Mode
no ip ospf message-digest-key
Use the L2TPC no ip ospf message-digest-key command to remove an old MD5 key. To enable
OSPF MD5 (Message-Digest) authentication, see ip ospf message-digest-key command on
page 15-8.
Syntax:
(config-l2tpc-{n})# no ip ospf message-digest-key key-id
Field
Definition
key-id
Enter an ID for this key. Range is 1-255.
Example: (config-l2tpc-1)# no ip ospf message-digest-key 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf priority
Use the L2TPC no ip ospf priority command to set the router priority to the default setting of
priority 1. To set the router priority, which determines the designated router for this network, see ip
ospf priority command on page 15-9.
Syntax:
(config-l2tpc-{n})# no ip ospf priority
Example: (config-l2tpc-1)# no ip ospf priority
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf retransmit-interval
Use the L2TPC ip ospf retransmit-interval command to restore the default value of 5 seconds. To
define the interval of time between link state advertisement retransmissions for adjacencies
belonging to the interface, see ip ospf retransmit-interval command on page 15-9.
Syntax:
(config-l2tpc-{n})# no ip ospf retransmit-interval
Example: (config-l2tpc-1)# no ip ospf retransmit-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
15-16
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - L2TPC Mode
no ip ospf transmit-delay
Use the L2TPC no ip ospf transmit-delay command to restore the default value of 1 second. To
define the estimated time to transmit a link state update packet on the interface, see ip ospf transmitdelay command on page 15-9.
Syntax:
(config-l2tpc-{n})# no ip ospf transmit-delay
Example: (config-l2tpc-1)# no ip ospf transmit-delay
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip primary-dns
Use the L2TPC no primary-dns command to disable the primary DNS. To set the DNS primary
IP address, see ip primary-dns command on page 15-10.
Syntax:
(config-l2tpc-{n})# no ip primary-dns
Example: (config-l2tpc-1)# no ip primary-dns
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip rip
Use the L2TPC no ip rip command to disable RIP on this interface. To enable RIP, see ip rip
command on page 15-10.
Syntax:
(config-l2tpc-{n})# no ip rip
Example: (config-l2tpc-1)# no ip rip
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip route
Use the L2TPC no ip route command remove an IP route. To add a route, see ip route command
on page 15-11.
Syntax:
(config-l2tpc-{n})# no ip route dest-ip-addr gateway
Field
Definition
dest-ip-addr
Enter destination IP address to remove.
gateway
Enter gateway IP address to remove.
Example: (config-l2tpc-1)# no ip route 192.168.100.200
192.168.100.254
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
15-17
Configuration - L2TPC Mode
no ip secondary-dns
Use the L2TPC no secondary-dns command to disable the secondary DNS. To enable the
secondary DNS, see ip secondary-dns command on page 15-12.
Syntax:
(config-l2tpc-{n})# no ip secondary-dns
Example: (config-l2tpc-1)# no ip secondary-dns
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp authentication
Use the L2TPC no ppp authentication command disable PPP authentication. To enable PPP
authentication, see ppp authentication command on page 15-21.
Syntax:
(config-l2tpc-{n})# no ppp authentication
Example: (config-l2tpc-1)# no ppp authentication
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp encryption
Use the L2TPC no ppp encryption command to disable PPP encryption. To enable PPP
encryption, see ppp encryption command on page 15-21.
Syntax:
(config-l2tpc-{n})# no ppp encryption
Example: (config-l2tpc-1)# no ppp encryption
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp exec-timeout
Use the L2TPC no ppp exec-timeout command to disable PPP idle time. To set the PPP maximum
idle time before hangup, see ppp exec-timeout command on page 15-21.
Syntax:
(config-l2tpc-{n})# no ppp exec-timeout
Example: (config-l2tpc-1)# no ppp exec-timeout
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
15-18
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - L2TPC Mode
no ppp on-demand
Use the L2TPC no ppp on-demand command to disable PPP on-demand. To enable PPP on
demand, see ppp on-demand command on page 15-22.
Syntax:
(config-l2tpc-{n})# no ppp on-demand
Example: (config-l2tpc-1)# no ppp on-demand
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp password
Use the L2TPC no ppp password command to remove the PPP password. To set the PPP password,
see ppp password command on page 15-22.
Syntax:
(config-l2tpc-{n})# no ppp password
Example: (config-l2tpc-1)# no ppp password
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp restart-timer
Use the L2TPC no ppp restart-timer command to set the restart timer back to the default setting.
To set the restart timer, see ppp restart-timer command on page 15-22.
Syntax:
(config-l2tpc-{n})# no ppp restart-timer
Example: (config-l2tpc-1)# no ppp restart-timer
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp time-btwn-reconnect
Use the L2TPC no ppp time-btwn-reconnect command to reset this time to the default settings.
To set the interval between reconnect attempts, see ppp time-btwn-reconnect command on
page 15-23.
Syntax:
(config-l2tpc-{n})# no ppp time-btwn-reconnect
Example: (config-l2tpc-1)# no ppp time-btwn-reconnect
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
15-19
Configuration - L2TPC Mode
no ppp username
Use the L2TPC no ppp username command remove the PPP username. To set a PPP user, see ppp
username command on page 15-23.
Syntax:
(config-l2tpc-{n})# no ppp username username
Example: (config-l2tpc-1)# no ppp username test-user-name
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no schedule-availability
Use the L2TPC no schedule-availability command to disable a schedule rule. To add a rule, see
schedule-availability command on page 15-23.
Syntax:
(config-l2tpc-{n})# no schedule-availability
Example: (config-l2tpc-1)# no schedule-availability
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no shutdown
Use the L2TPC no shutdown command to set the interface up (In-Service). To set the interface
down (Out-of-Service), see shutdown command on page 15-24.
Syntax:
(config-l2tpc-{n})# no shutdown
Example: (config-l2tpc-1)# no shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no sip-alg
Use the L2TPC no sip-alg command to disable SIP ALG on this interface. To enable SIP ALG, see
sip-alg command on page 15-24.
Syntax:
(config-l2tpc-{n})# no sip-alg
Example: (config-l2tpc-1)# no sip-alg
Supported Platforms: Adit 3104, Adit 3500, MSR
15-20
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - L2TPC Mode
ppp authentication
Use the L2TPC ppp authentication command to configure the support of authentication types for the
password. To disable PPP authentication, see no ppp authentication command on page 15-18.
Syntax:
(config-l2tpc-{n})# ppp authentication {chap|ms-chap|
ms-chapv2|pap}
Field
Definition
chap
Support Challenge Handshake Authentication (CHAP)
ms-chap
Support Microsoft CHAP (MS-CHAP).
ms-chapv2
Support Microsoft CHAP Version 2 (MS-CHAPv2).
pap
Support an unencrypted password.
Example: (config-l2tpc-1)# ppp authentication chap
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp encryption
Use the L2TPC ppp encryption command to configure the PPP encryption. To disable PPP encryption,
see no ppp encryption command on page 15-18.
Syntax:
(config-l2tpc-{n})# ppp encryption {40-bit|128-bit}
Field
Definition
40-bit
Support Encryption (40 bit keys)
128-bit
Support Maximum Strength Encryption (128 bit keys)
Example: (config-l2tpc-1)# ppp encryption 40-bit
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp exec-timeout
Use the L2TPC ppp exec-timeout command to set the PPP maximum idle time before hangup.To
disable PPP idle time, see no ppp exec-timeout command on page 15-18.
Syntax:
(config-l2tpc-{n})# ppp exec-timeout minutes
Field
Definition
minutes
Range is 0 - 99999 minutes.
Example: (config-l2tpc-1)# ppp exec-timeout 150
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
15-21
Configuration - L2TPC Mode
ppp on-demand
Use the L2TPC ppp on-demand command to enable on demand the feature. On demand attempts to
connect only when packets are sent. To disable PPP on demand, see no ppp encryption command on
page 15-18.
Syntax:
(config-l2tpc-{n})# ppp on-demand
Example: (config-l2tpc-1)# ppp on-demand
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp password
Use the L2TPC ppp password command set the PPP password. To delete a PPP password, see no ppp
password command on page 15-19.
Syntax:
(config-l2tpc-{n})# ppp password password
Field
Definition
password
Enter the PPP password, with a maximum of 19 characters.
Example: (config-l2tpc-1)# ppp password test-user-pswrd
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp restart-timer
Use the L2TPC ppp restart-timer command to configure the PPP restart timer. To set the restart timer
to the default setting, see no ppp restart-timer command on page 15-19.
Syntax:
(config-l2tpc-{n})# ppp restart-timer seconds
Field
Definition
seconds
Range is 1 - 65535 seconds. Default is 3 seconds.
Example: (config-l2tpc-1)# ppp restart-timer 15
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
15-22
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - L2TPC Mode
ppp time-btwn-reconnect
Use the L2TPC ppp time-btwn-reconnect command configure the time between reconnect attempts.
To reset to default value, see no ppp time-btwn-reconnect command on page 15-19.
Syntax:
(config-l2tpc-{n})# ppp time-btwn-reconnect seconds
Field
Definition
seconds
Set the interval of time between reconnect attempts.
Range is 0 - 99999 seconds with a default of 0.
Example: (config-l2tpc-1)# ppp time-btwn-reconnect 15
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp username
Use the L2TPC ppp username command set the PPP Login User Name. To delete a PPP user, see no
ppp username command on page 15-20.
Syntax:
(config-l2tpc-{n})# ppp username username
Field
Definition
username
Enter the Username, with a maximum of 19 characters.
Example: (config-l2tpc-1)# ppp username test-user-name
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
schedule-availability
Use the L2TPC schedule-availability command to apply a schedule rule to this interface. To delete a
schedule, see no schedule-availability command on page 15-20.
Syntax:
(config-l2tpc-{n})# schedule-availability time-range scheduleid
Field
Definition
schedule-id
Enter an existing schedule rule name. See time-range command on
page 4-62 to set the schedule-id
Example: (config-l2tpc-1)# schedule-availability time-range 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
15-23
Configuration - L2TPC Mode
shutdown
Use the L2TPC shutdown command to disable the interface. To set the interface up
(In-Service), see no shutdown command on page 15-20.
Syntax:
(config-l2tpc-{n})# shutdown
Example: (config-l2tpc-1)# shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
sip-alg
Use the L2TPC sip-alg command to enable SIP ALG. To disable SIP ALG, see no sip-alg command on
page 15-20.
Syntax:
(config-l2tpc-{n})# sip-alg enable
Example: (config-l2tpc-1)# sip-alg enable
Supported Platforms: Adit 3104, Adit 3500, MSR
15-24
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
16
Configuration - OSPF Mode
The Router OSPF Configuration commands allow the user to configure the OSPF parameters.
OSPF (Open Shortest Path First) is a protocol based on the link-states of routers within a network. OSPF
supports hierarchical routing by segmenting a larger network into smaller more manageable networks
called areas.
Enter this sub-group with the (config)# router ospf command from the Configuration mode.
The Router OSPF commands are represented by the (config-ospf)# prompt.
Router OSPF Commands
•
•
•
•
•
•
•
•
•
•
area authentication
area stub
compatible rfc1583
do
end
exit
history
network area
no commands
router-id
Configuration - OSPF Mode
area commands
Note: For the following area commands, the first command that enters the area ID will set this
parameter. The no area command will remove a specific area from the configuration. See the no area
command on page 16-7.
area authentication
Use the Router OSPF area authentication command to enable authentication method (either
message-digest or simple authentication) for an OSPF area. The default setting is no authentication.
Note: If the optional parameter (message-digest) is not entered, the authentication method of
simple authentication is applied to the area. To remove an area’s authentication see no area
authentication command on page 16-7.
Syntax:
(config-ospf)# area area-id authentication [message-digest]
Field
Definition
area-id
Identifier of the area for which authentication is to be enabled, in the
form:
area number - Range 0-4294967295
area IP address - IP address of the area.
message-digest
Optional parameter. Enables MD5 Authentication on the area.
Example: (config-ospf)# area 1 authentication
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
area stub
Use the Router OSPF area stub command to set an area as a Stub area. Note: A Stub area is an area
that does not receive LSAs. To remove the "stub" destination of an area, see no area stub command
on page 16-7.
Syntax:
(config-ospf)# area area-id stub
Field
Definition
area-id
Identifier of the stub area, in the form:
ID number - Range 0-4294967295
IP address - IP address of the area.
Example: (config-ospf)# area 1 stub
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
16-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - OSPF Mode
compatible rfc1583
Use the Router OSPF compatible rfc1583 command to restore the method used to calculate summary
route costs per RFC 1583. To disable RFC 1583 compatibility, see the no compatible rfc1583 command
on page 16-8.
Syntax:
(config-ospf)# compatible rfc1583
Example: (config-ospf)# compatible rfc1583
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
16-3
Configuration - OSPF Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
16-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - OSPF Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-ospf)# end
Example: (config-ospf)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-ospf)# exit
Example: (config-ospf)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
history
Use the history command to display commands that have been entered in this session.
Syntax:
(config-ospf)# history
Example: (config-ospf)# history
router-id 10.1.1.1
history
compatible rfc1583
area 1 authentication
area 1 stub
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
16-5
Configuration - OSPF Mode
network area
Use the Router OSPF network area command to define the interfaces on which OSPF will run and set
the ID for those interfaces. To disable OSPF routing for the interface defined, see no network area
command on page 16-8.
Syntax:
(config-ospf)# network address wildcard-mask area area-id
Field
Definition
address
IP address
wildcard-mask
IP address-type mask that includes "don’t care" bits.
area-id
Identifier of the stub area, in the form:
ID number - Range 0-4294967295
IP address - IP address of the area.
If you intend to associate areas with IP subnets, specify a subnet
address as the value of the area-id.
Example: (config-ospf)# network 192.168.1.1 0.0.0.255 area 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
16-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - OSPF Mode
no commands
no area
Use the Router OSPF no area command to remove a specific area from the OSPF configuration.
To set an area, see the area commands command on page 16-2, or area stub command on
page 16-2, the first use of either command will set the area.
Syntax:
(config-ospf)# no area area-id
Field
Definition
area-id
ID of area to be removed, in the form:
area number - Range 0-4294967295
area IP address - IP address of the area.
Example: (config-ospf)# no area 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no area authentication
Use the Router OSPF no area authentication command to remove an area’s authentication. See
the area commands command on page 16-2 for the counterpart of this command.
Syntax:
(config-ospf)# no area area-id authentication
Field
Definition
area-id
Area ID for which authentication is to be removed, in the form:
area number - Range 0-4294967295
area IP address - IP address of the area.
Example: (config-ospf)# no area 1 authentication
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no area stub
Use the Router OSPF no area stub command to remove the definition of an area as a Stub area. See
the area stub command on page 16-2 for the counterpart of this command.
Syntax:
(config-ospf)# no area area-id stub
Field
Definition
area-id
Identifier of the stub area, in the form:
ID number - Range 0-4294967295
IP address - IP address of the area.
Example: (config-ospf)# no area 1 stub
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
16-7
Configuration - OSPF Mode
no compatible rfc1583
Use the Router OSPF no compatible rfc1583 command to disable RFC 1583 compatibility. To
restore RFC 1583 compatibility, see compatible rfc1583 command on page 16-3
Syntax:
(config-ospf)# no compatible rfc1583
Example: (config-ospf)# no compatible rfc1583
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no network area
Use the Router OSPF no network area command to disable OSPF routing for the interface defined.
To define the interfaces on which OSPF will run and set the ID for those interfaces, see network
area command on page 16-6.
Syntax:
(config-ospf)# no network address wildcard-mask area area-id
Field
Definition
address
IP address
wildcard-mask
Wildcard mask to remove.
area-id
Identifier of the stub area, in the form:
ID number - Range 0-4294967295
IP address - IP address of the area.
Example: (config-ospf)# no network 192.168.1.1 0.0.0.255 area 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no router-id
Use the Router OSPF no router-id command to force OSPF to use the previous OSPF router ID
behavior. To use a fixed router ID, see router-id command on page 16-9.
Syntax:
(config-ospf)# no router-id
Example: (router-ospf)# no router-id
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
16-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - OSPF Mode
router-id
Use the Router OSPF router-id command to use a fixed router ID. To force OSPF to use the previous
OSPF router ID behavior use the no form of this command, see no router-id command on page 16-8.
Syntax:
(config-ospf)# router-id address
Field
Definition
address
Router ID in IP address format.
Example: (router-ospf)# router-id 10.1.1.1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
16-9
Configuration - OSPF Mode
Sample Configuration
Sample Configuration
ospf
router ospf
no compatible rfc1583
router-id 192.168.3.251
network 192.168.3.0 0.0.0.255 area 0.0.0.1
interface ethernet 1
ip address 192.168.2.251 mask 255.255.255.0
description Ethernet 1
ip mtu auto
no tos ip
tos ip value 0x0
ip default-gateway 0.0.0.0
no ip dhcp auto-provision
no ip primary-dns
no ip secondary-dns
ip route-mode route
no ip default-route
no ip proxy-arp
no ip rip
ip rip receive-version 1or2
ip rip send-version 2-bcast
no firewall
metric 50
no shutdown
speed auto
full-duplex
remote-admin enable
no schedule-availability
ip ospf message-digest-key 1 md5 test
ip ospf authentication-key test2
ip ospf cost 2
16-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - OSPF Mode
Sample Configuration
ip ospf priority 2
exit
interface ethernet 2
ip address 192.168.3.251 mask 255.255.255.0
description Ethernet 2
ip mtu auto
ip default-gateway 192.168.3.1
ip dhcp auto-provision
no ip primary-dns
no ip secondary-dns
ip route-mode route
ip default-route enable
no ip proxy-arp
no ip rip
ip rip receive-version 1or2
ip rip send-version 2-bcast
sip-alg enable
no firewall
metric 40
no shutdown
speed auto
full-duplex
no schedule-availability
ip ospf message-digest-key 1 md5 123 (test)
ip ospf authentication-key (test2)
ip ospf cost 2
ip ospf hello-interval 25
exit
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
16-11
Configuration - OSPF Mode
Sample Configuration
16-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
17
Configuration - PPTPC Mode
The PPTPC Configuration commands allow the user to configure the VPN (Virtual Private Network)
Point-to-Point Tunneling Protocol Client parameters.
Enter this sub-group with the (config)# pptpc command from the Configuration mode.
The VPN PPTPC commands are represented by the (config-pptpc-n)# prompt.
PPTP Client Commands
• do
• ip primary-dns
• end
• ip rip
• exit
• ip route
• firewall
• ip route-mode
• history
• ip secondary-dns
• host-ip
• metric
• ip address
• no commands
• ip default-route
• ppp authentication
• ip mtu
• ppp encryption
• ip ospf authentication
• ppp exec-timeout
• ip ospf authentication-key
• ppp on-demand
• ip ospf cost
• ppp password
• ip ospf dead-interval
• ppp restart-timer
• ip ospf disable
• ppp time-btwn-reconnect
• ip ospf hello-interval
• ppp username
• ip ospf message-digest-key
• schedule-availability
• ip ospf priority
• shutdown
• ip ospf retransmit-interval
• sip-alg
• ip ospf transmit-delay
Configuration - PPTPC Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
17-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPC Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-pptpc-{n})# end
Example: (config-pptpc-1)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-pptpc-{n})# exit
Example: (config-pptpc-1)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
firewall
Use the PPTP Client firewall command to enable the configured firewall. To delete a preference, see
no firewall command on page 17-13.
Syntax:
(config-pptpc-{n})# firewall enable
Example: (config-pptpc-1)# firewall enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
17-3
Configuration - PPTPC Mode
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-pptpc-{n})# history
Example: (config-pptpc-1)# history
history
ip mtu aut
ip rip enable
ip rip receive-version 1or2
ip route-mode route
metric 3
ppp exec-timeout 1500
ppp restart-timer 600
ppp authentication chap
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
host-ip
Use the PPTP Client host-ip command to configure the IP address for the host.
Syntax:
(config-pptpc-{n})# host-ip {address}
Field
Definition
address
Enter the IP address for the host.
Example: (config-pptpc-1)# host-ip 192.168.2.101
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
17-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPC Mode
ip address
Use the PPTP Client ip address command to configure the IP address for the port. To remove an IP
address, see no ip address command on page 17-13.
Syntax:
(config-pptpc-{n})# ip address {address mask mask|auto
|unnumbered} [secondary]
Field
Definition
address
Enter an IP address to assign to the port.
mask
Enter a subnet mask for the IP address.
auto
Uses IPCP to assign an IP address.
unnumbered
Treat this as an un-numbered interface, as per RFC 1812.
secondary
Optional parameter, defines the address to be a secondary IP address.
Example: (config-pptpc-1)# ip address 192.168.2.100 mask 255.255.255.0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip default-route
Use the PPTP Client ip default-route command to enable the default route. To disable the default route,
see no ip default-route command on page 17-13.
Syntax:
(config-pptpc-{n})# ip default-route enable
Example: (config-pptpc-1)# ip default-route enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip mtu
Use the PPTP Client ip mtu command to set the Maximum Transmission Unit. Sets the largest packet
size (bytes) the network will allow to transmit.
Syntax:
(config-pptpc-{n})# ip mtu {size|auto}
Field
Definition
size
Allows the user to set the Maximum Transmission Unit (MTU).
size = Range of 576 to 1500 bytes.
auto
Auto sets the MTU at 1500 bytes.
Example: (config-pptpc-1)# ip mtu auto
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
17-5
Configuration - PPTPC Mode
ip ospf authentication
Use the PPTP Client ip ospf authentication command to enable the authentication method (either
message-digest or simple authentication) for this interface. To remove the authentication type for this
interface set the parameter to null or see no ip ospf authentication command on page 17-13.
Note: If an optional parameter is not entered, the authentication method of simple authentication is
applied to the interface.
Syntax:
(config-pptpc-{n})# ip ospf authentication [message-digest|
null]
Field
Definition
message-digest
Optional parameter. Enables MD5 Authentication on the area.
null
Optional parameter. No authentication is used. Note: This is useful for
overriding password or message-digest authentication if configured
for an area.
Example: (config-pptpc-1)# ip ospf authentication message-digest
Note: The authentication key must be defined before this command is implemented.
Therefore if setting simple authentication:
Example: ip ospf authentication-key pass777
ip ospf authentication
Therefore if setting message-digest:
Example: ip ospf message-digest-key 1 md5 pass777
ip ospf authentication message-digest
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
17-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPC Mode
ip ospf authentication-key
Use the PPTP Client ip ospf authentication-key command to assign a password to be used by
neighboring routers, that are using OSPF’s simple password authentication.To remove a previously
assigned password, see no ip ospf authentication-key command on page 17-14.
Syntax:
(config-pptpc-{n})# ip ospf authentication-key password
Field
Definition
password
Enter a password, with up to 8 characters.
Example: (config-pptpc-1)# ip ospf authentication-key pass777
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf cost
Use the PPTP Client ip ospf cost command to define the cost of sending a packet on this serial interface.
To reset the path cost to the default setting of 0, see no ip ospf cost command on page 17-14.
Syntax:
(config-pptpc-{n})# ip ospf cost cost
Field
Definition
cost
Range is 1-65535, with a default of 0.
Example: (config-pptpc-1)# ip ospf cost 5
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf dead-interval
Use the PPTP Client ip ospf dead-interval command to define the interval of time that no hello packets
have been seen before neighbors declare the router down. To reset the interval of time to the default
setting of 40 seconds, see no ip ospf dead-interval command on page 17-14.
Syntax:
(config-pptpc-{n})# ip ospf dead-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 40.
Note: This value must be the same for all nodes on the network.
Example: (config-pptpc-1)# ip ospf dead-interval 50
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
17-7
Configuration - PPTPC Mode
ip ospf disable
Use the PPTP Client ip ospf disable command to disable OSPF processing on this interface. To enable
OSPF on this interface, see no ip ospf disable command on page 17-14.
Syntax:
(config-pptpc-{n})# ip ospf disable all
Example: (config-pptpc-1)# ip ospf disable all
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf hello-interval
Use the PPTP Client ip ospf hello-interval command to define the interval of time between hello
packets sent on the interface. To reset the interval of time to the default setting of the path cost to the
default setting of 10 seconds, see no ip ospf hello-interval command on page 17-15.
Syntax:
(config-pptpc-{n})# ip ospf hello-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 10.
Note: This value must be the same for all nodes on the network.
Example: (config-pptpc-1)# ip ospf hello-interval 12
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf message-digest-key
Use the PPTP Client ip ospf message-digest-key command to enable OSPF MD5 (Message-Digest)
authentication. To remove an old MD5 key, see no ip ospf message-digest-key command on page 17-15.
Syntax:
(config-pptpc-{n})# ip ospf message-digest-key key-id md5 key
Field
Definition
key-id
Enter an ID for this key. Range is 1-255.
key
Enter a alphanumeric password, with up to 8 characters.
Example: (config-pptpc-1)# ip ospf message-digest-key 1 md5 key1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
17-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPC Mode
ip ospf priority
Use the PPTP Client ip ospf priority command to set the router priority, which determines the
designated router for this network. To restore the default setting of priority 1, see no ip ospf priority
command on page 17-15.
Syntax:
(config-pptpc-{n})# ip ospf priority priority
Field
Definition
priority
Enter an ID for this key. Range is 0-255.
Example: (config-pptpc-1)# ip ospf priority 2
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf retransmit-interval
Use the PPTP Client ip ospf retransmit-interval command to define the interval of time between link
state advertisement retransmissions for adjacencies belonging to the interface. To restore the default
value of 5 seconds, see no ip ospf retransmit-interval command on page 17-16.
Syntax:
(config-pptpc-{n})# ip ospf retransmit-interval seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 5.
Example: (config-pptpc-1)# ip ospf retransmit-interval 10
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip ospf transmit-delay
Use the PPTP Client ip ospf transmit-delay command to define the estimated time to transmit a link
state update packet on the interface. To restore the default value of 1 second, see no ip ospf transmitdelay command on page 17-16.
Syntax:
(config-pptpc-{n})# ip ospf transmit-delay seconds
Field
Definition
seconds
Range is 1-65535 seconds, with a default of 1.
Example: (config-pptpc-1)# ip ospf transmit-delay 10
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
17-9
Configuration - PPTPC Mode
ip primary-dns
Use the PPTP Client ip primary-dns command to configure the primary DNS. To delete a primary
DNS, see no ip primary-dns command on page 17-16.
Syntax:
(config-pptpc-{n})# ip primary-dns address
Field
Definition
address
Enter the IP address of the primary server.
Example: (config-pptpc-1)# ip primary-dns 192.168.2.100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip rip
ip rip enable
Use the PPTP Client ip rip enable command to enable RIP on this interface. To disable RIP, see
no ip rip command on page 17-16.
Syntax:
(config-pptpc-{n})# ip rip enable
Example: (config-pptpc-1)# ip rip enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip rip receive-version
Use the PPTP Client ip rip receive-version command to configure the RIP receive messages on
this interface.
Syntax:
(config-pptpc-{n})# ip rip receive-version {1|2|1or2|none}
Field
Definition
1|2|1or2
Receive RIP version 1
Receive RIP version 2
Receive RIP version 1 and 2.
none
Set RIP version to none.
Example: (config-pptpc-1)# ip rip receive-version none
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
17-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPC Mode
ip rip send-version
Use the PPTP Client ip rip send-version command to configure the send RIP messages on this
interface.
Syntax:
(config-pptpc-{n})# ip rip send-version {1|2-bcast|2-mcast
|none}
Field
Definition
1
Send RIP version 1.
2-bcast
Send RIP version 2 - Broadcast.
2-mcast
Send RIP version 2 - Multicast.
none
Set RIP version to none.
Example: (config-pptpc-1)# ip rip send-version 2-bcast
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip route
Use the PPTP Client ip route command to configure the IP routing on this interface. To delete a route,
see no ip route command on page 17-17.
Syntax:
(config-pptpc-{n})# ip route dest-ip-addr mask mask gateway
gateway metric metric
Field
Definition
dest-ip-addr
Enter the destination IP address.
mask
Enter the mask of the above address.
gateway
Enter the gateway IP address.
metric
Metric of IP network on this interface in Adit 3500 Routing Table.
Range is 0-255, with a default is 10.
Example: (config-pptpc-1)# ip route 192.168.100.200 mask 255.255.255.0
gateway 192.168.100.254 mask 125
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
17-11
Configuration - PPTPC Mode
ip route-mode
Use the PPTP Client ip route-mode command to configure the routing mode.
Syntax:
(config-pptpc-{n})# ip route-mode {napt|route}
Field
Definition
napt
Set to NAPT mode. Default.
NAPT is used if doing private IPs on the Ethernet side or if you want
to hide specific publics on the internal side.
route
Set to Route mode. Routing is used if public is visible on both sides.
Example: (config-pptpc-1)# ip route-mode napt
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ip secondary-dns
Use the PPTP Client ip secondary-dns command to configure the secondary DNS. To delete a
secondary DNS address, see no ip secondary-dns command on page 17-17.
Syntax:
(config-pptpc-{n})# ip secondary-dns address
Field
Definition
address
Enter the IP address of the secondary Domain Name Server (DNS).
Example: (config-pptpc-1)# ip secondary-dns 192.168.1.200
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
metric
Use the PPTP Client metric command to configure the Metric of the IP network on this interface.
Syntax:
(config-pptpc-{n})# metric metric
Field
Definition
metric
Range is 0-255, with a default is 10.
Example: (config-pptpc-1)# metric 150
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
17-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPC Mode
no commands
no firewall
Use the PPTP Client no firewall command to disable the configured firewall. To enable the
firewall, see firewall command on page 17-3.
Syntax:
(config-pptpc-{n})# no firewall
Example: (config-pptpc-1)# no firewall
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip address
Use the PPTP Client no ip address command to remove the IP address assigned to the port. To set
the Serial IP address, see ip address command on page 17-5.
Syntax:
(config-pptpc-{n})# no ip address address
Field
Definition
address
Enter the IP address to remove.
Example: (config-pptpc-1)# no ip address 192.168.1.100
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip default-route
Use the PPTP Client no ip default-route command to disable the default route. To set the default
IP address, see ip default-route command on page 17-5.
Syntax:
(config-pptpc-{n})# no ip default-route
Example: (config-pptpc-1)# no ip default-route
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf authentication
Use the PPTP Client no ip ospf authentication command to disable the authentication method for
this serial interface. To enable the authentication type for this interface see ip ospf authentication
command on page 17-6.
Syntax:
(config-pptpc-{n})# no ip ospf authentication
Example: (config-pptpc-1)# no ip ospf authentication
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
17-13
Configuration - PPTPC Mode
no ip ospf authentication-key
Use the PPTP Client no ip ospf authentication-key command to remove a password to be used by
neighboring routers, that are using OSPF’s simple password authentication.To assign a password,
see ip ospf authentication-key command on page 17-7.
Syntax:
(config-pptpc-{n})# no ip ospf authentication-key
Example: (config-pptpc-1)# no ip ospf authentication-key
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf cost
Use the PPTP Client no ip ospf cost command to reset the cost path to the default setting of 0. To
define the cost of sending a packet on this serial interface, see ip ospf cost command on page 17-7.
Syntax:
(config-pptpc-{n})# no ip ospf cost
Example: (config-pptpc-1)# no ip ospf cost
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf dead-interval
Use the PPTP Client no ip ospf dead-interval command to reset the interval of time to the default
setting of 40 seconds. To define the interval of time that no hello packets have been seen before
neighbors declare the router down, see ip ospf dead-interval command on page 17-7.
Syntax:
(config-pptpc-{n})# no ip ospf dead-interval
Example: (config-pptpc-1)# no ip ospf dead-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf disable
Use the PPTP Client no ip ospf disable command to enable OSPF processing on this interface. To
disable OSPF on this interface, see ip ospf disable command on page 17-8.
Syntax:
(config-pptpc-{n})# no ip ospf disable all
Example: (config-pptpc-1)# no ip ospf disable all
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
17-14
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPC Mode
no ip ospf hello-interval
Use the PPTP Client no ip ospf hello-interval command to reset the interval of time to the default
setting of the path cost to the default setting of 10 seconds. To define the interval of time between
hello packets sent on the interface, see ip ospf hello-interval command on page 17-8.
Syntax:
(config-pptpc-{n})# no ip ospf hello-interval
Example: (config-pptpc-1)# no ip ospf hello-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf message-digest-key
Use the PPTP Client no ip ospf message-digest-key command to remove an old MD5 key. To
enable OSPF MD5 (Message-Digest) authentication, see ip ospf message-digest-key command on
page 17-8.
Syntax:
(config-pptpc-{n})# no ip ospf message-digest-key key-id
Field
Definition
key-id
Enter an ID for this key. Range is 1-255.
Example: (config-pptpc-1)# no ip ospf message-digest-key 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf priority
Use the PPTP Client no ip ospf priority command to set the router priority to the default setting of
priority 1. To set the router priority, which determines the designated router for this network, see ip
ospf priority command on page 17-9.
Syntax:
(config-pptpc-{n})# no ip ospf priority
Example: (config-pptpc-1)# no ip ospf priority
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
17-15
Configuration - PPTPC Mode
no ip ospf retransmit-interval
Use the PPTP Client ip ospf retransmit-interval command to restore the default value of 5
seconds. To define the interval of time between link state advertisement retransmissions for
adjacencies belonging to the interface, see ip ospf retransmit-interval command on page 17-9.
Syntax:
(config-pptpc-{n})# no ip ospf retransmit-interval
Example: (config-pptpc-1)# no ip ospf retransmit-interval
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip ospf transmit-delay
Use the PPTP Client no ip ospf transmit-delay command to restore the default value of 1 second.
To define the estimated time to transmit a link state update packet on the interface, see ip ospf
transmit-delay command on page 17-9.
Syntax:
(config-pptpc-{n})# no ip ospf transmit-delay
Example: (config-pptpc-1)# no ip ospf transmit-delay
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip primary-dns
Use the PPTP Client no primary-dns command to disable the primary DNS. To set the DNS
primary IP address, see ip primary-dns command on page 17-10.
Syntax:
(config-pptpc-{n})# no ip primary-dns
Example: (config-pptpc-1)# no ip primary-dns
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip rip
Use the PPTP Client no ip rip command to disable RIP on this interface. To enable RIP, see ip rip
command on page 17-10.
Syntax:
(config-pptpc-{n})# no ip rip
Example: (config-pptpc-1)# no ip rip
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
17-16
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPC Mode
no ip route
Use the PPTP Client no ip route command remove an IP route. To add a route, see ip route
command on page 17-11.
Syntax:
(config-pptpc-{n})# no ip route dest-ip-addr gateway
Field
Definition
dest-ip-addr
Enter destination IP address to remove.
gateway
Enter gateway IP address to remove.
Example: (config-pptpc-1)# no ip route 192.168.100.200
192.168.100.254
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ip secondary-dns
Use the PPTP Client no secondary-dns command to disable the secondary DNS. To enable the
secondary DNS, see ip secondary-dns command on page 17-12.
Syntax:
(config-pptpc-{n})# no ip secondary-dns
Example: (config-pptpc-1)# no ip secondary-dns
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp authentication
Use the PPTP Client no ppp authentication command disable PPP authentication. To enable PPP
authentication, see ppp authentication command on page 17-20.
Syntax:
(config-pptpc-{n})# no ppp authentication
Example: (config-pptpc-1)# no ppp authentication
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp encryption
Use the PPTP Client no ppp encryption command to disable PPP encryption. To enable PPP
encryption, see ppp encryption command on page 17-20.
Syntax:
(config-pptpc-{n})# no ppp encryption
Example: (config-pptpc-1)# no ppp encryption
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
17-17
Configuration - PPTPC Mode
no ppp exec-timeout
Use the PPTP Client no ppp exec-timeout command to disable PPP idle time. To set the PPP
maximum idle time before hangup, see ppp exec-timeout command on page 17-21.
Syntax:
(config-pptpc-{n})# no ppp exec-timeout
Example: (config-pptpc-1)# no ppp exec-timeout
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp on-demand
Use the PPTP Client no ppp on-demand command to disable PPP on-demand. To enable PPP on
demand, see ppp on-demand command on page 17-21.
Syntax:
(config-pptpc-{n})# no ppp on-demand
Example: (config-pptpc-1)# no ppp on-demand
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp password
Use the PPTP Client no ppp password command to remove the PPP password. To set the PPP
password, see ppp password command on page 17-21.
Syntax:
(config-pptpc-{n})# no ppp password
Example: (config-pptpc-1)# no ppp password
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp restart-timer
Use the PPTP Client no ppp restart-timer command to set the PPP restart timer to the default
setting. To configure the PPP restart timer, see ppp restart-timer command on page 17-22.
Syntax:
(config-pptpc-{n})# no ppp restart-timer
Example: (config-pptpc-1)# no ppp restart-timer
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
17-18
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPC Mode
no ppp time-btwn-reconnect
Use the PPTP Client no ppp time-btwn-reconnect command to set the time between reconnect
attempts to the default setting. To configure the time between reconnect attempts, see ppp timebtwn-reconnect command on page 17-22.
Syntax:
(config-pptpc-{n})# no ppp time-btwn-reconnect
Example: (config-pptpc-1)# no ppp time-btwn-reconnect
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp username
Use the PPTP Client no ppp username command remove the PPP username. To set a PPP user, see
ppp username command on page 17-22.
Syntax:
(config-pptpc-{n})# no ppp username username
Example: (config-pptpc-1)# no ppp username test-user-name
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no schedule-availability
Use the PPTP Client no schedule-availability command to disable a schedule rule. To add a rule,
see schedule-availability command on page 17-23.
Syntax:
(config-pptpc-{n})# no schedule-availability
Example: (config-pptpc-1)# no schedule-availability
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no shutdown
Use the PPTP Client no shutdown command to set the interface up (In-Service). To set the interface
down (Out-of-Service), see shutdown command on page 17-23.
Syntax:
(config-pptpc-{n})# no shutdown
Example: (config-pptpc-1)# no shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
17-19
Configuration - PPTPC Mode
no sip-alg
Use the PPTP Client no sip-alg command to disable SIP ALG on this interface. To enable SIP ALG,
see sip-alg command on page 17-23.
Syntax:
(config-pptpc-{n})# no sip-alg
Example: (config-pptpc-1)# no sip-alg
Supported Platforms: Adit 3104, Adit 3500, MSR
ppp authentication
Use the PPTP Client ppp authentication command to configure the support of authentication types for
the password. To disable PPP authentication, see no ppp authentication command on page 17-17.
Syntax:
(config-pptpc-{n})# ppp authentication {chap|ms-chap|
ms-chapv2|pap}
Field
Definition
chap
Support Challenge Handshake Authentication (CHAP)
ms-chap
Support Microsoft CHAP (MS-CHAP).
ms-chapv2
Support Microsoft CHAP Version 2 (MS-CHAPv2).
pap
Support an unencrypted password.
Example: (config-pptpc-1)# ppp authentication chap
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp encryption
Use the PPTP Client ppp encryption command to configure the PPP encryption. To disable PPP
encryption, see no ppp encryption command on page 17-17.
Syntax:
(config-pptpc-{n})# ppp encryption {40-bit|128-bit}
Field
Definition
40-bit
Support Encryption (40 bit keys)
128-bit
Support Maximum Strength Encryption (128 bit keys)
Example: (config-pptpc-1)# ppp encryption 40-bit
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
17-20
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPC Mode
ppp exec-timeout
Use the PPTP Client ppp exec-timeout command to set the PPP maximum idle time before hangup.To
disable PPP idle time, see no ppp exec-timeout command on page 17-18.
Syntax:
(config-pptpc-{n})# ppp exec-timeout minutes
Field
Definition
minutes
Range is 0 - 99999 minutes.
Example: (config-pptpc-1)# ppp exec-timeout 150
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp on-demand
Use the PPTP Client ppp on-demand command to enable on demand the feature. On demand attempts
to connect only when packets are sent. To disable PPP on demand, see no ppp encryption command on
page 17-17.
Syntax:
(config-pptpc-{n})# ppp on-demand
Example: (config-pptpc-1)# ppp on-demand
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp password
Use the PPTP Client ppp password command set the PPP password. To delete a PPP password, see no
ppp password command on page 17-18.
Syntax:
(config-pptpc-{n})# ppp password password
Field
Definition
password
Enter the PPP password, with a maximum of 19 characters.
Example: (config-pptpc-1)# ppp password test-user-pswrd
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
17-21
Configuration - PPTPC Mode
ppp restart-timer
Use the PPTP Client ppp restart-timer command to configure the PPP restart timer. To reset to the
default setting, see no ppp restart-timer command on page 17-18.
Syntax:
(config-pptpc-{n})# ppp restart-timer seconds
Field
Definition
seconds
Range is 1 - 65535 seconds. Default is 3 seconds.
Example: (config-pptpc-1)# ppp restart-timer 15
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp time-btwn-reconnect
Use the PPTP Client ppp time-btwn-reconnect command configure the time between reconnect
attempts. To reset to the default setting, see no ppp time-btwn-reconnect command on page 17-19.
Syntax:
(config-pptpc-{n})# ppp time-btwn-reconnect seconds
Field
Definition
seconds
Set the interval of time between reconnect attempts.
Range is 0 - 99999 seconds with a default of 0.
Example: (config-pptpc-1)# ppp time-btwn-reconnect 15
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp username
Use the PPTP Client ppp username command set the PPP Login User Name. To delete a PPP user, see
no ppp username command on page 17-19.
Syntax:
(config-pptpc-{n})# ppp username username
Field
Definition
username
Enter the Username, with a maximum of 19 characters.
Example: (config-pptpc-1)# ppp username test-user-name
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
17-22
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPC Mode
schedule-availability
Use the PPTP Client schedule-availability command to apply a schedule rule to this interface. To
delete a schedule, see no schedule-availability command on page 17-19.
Syntax:
(config-pptpc-{n})# schedule-availability time-range scheduleid
Field
Definition
schedule-id
Enter an existing schedule rule name. See time-range command on
page 4-62 to set the schedule-id
Example: (config-pptpc-1)# schedule-availability time-range 1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
shutdown
Use the PPTP Client shutdown command to disable the interface. To set the interface up
(In-Service), see no shutdown command on page 17-19.
Syntax:
(config-pptpc-{n})# shutdown
Example: (config-pptpc-1)# shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
sip-alg
Use the PPTP Client sip-alg command to enable SIP ALG. To disable SIP ALG, see no sip-alg
command on page 17-20.
Syntax:
(config-pptpc-{n})# sip-alg enable
Example: (config-pptpc-1)# sip-alg enable
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
17-23
Configuration - PPTPC Mode
17-24
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
18
Configuration - PPTPS Mode
The PPTP Server Configuration commands allow the user to configure the VPN (Virtual Private
Network) Point-to Point Tunneling Protocol Server parameters.
Enter this sub-group with the (config)# pptps command from the Configuration mode.
The VPN PPTP Server commands are represented by the (config-pptps)# prompt.
PPTP Server Commands
• do
• end
• end-address
• exit
• history
• idle-time
• no commands
• ppp authentication
• ppp encryption
• shutdown
• start-address
Configuration - PPTPS Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
18-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPS Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-pptps)# end
Example: (config-pptps)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
end-address
Use the PPTP Server end-address command to set the PPTP remote host IP address range end.
Syntax:
(config-pptps)# end-address end-ip-address
Field
Definition
end-ip-address
Enter the end IP address of the range.
Example: (config-pptps)# end-address 192.168.1.250
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-pptps)# exit
Example: (config-pptps)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
18-3
Configuration - PPTPS Mode
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-pptps)# history
Example: (config-pptps)# history
ppp
end-address 192.168.1.175
ppp encryption
ppp authentication pap
idle-time 99999
start-address 192.168.1.1
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
idle-time
Use the PPTP Server idle-time command to set the maximum idle time for a PPTP connection.To reset
the idle-time to the default setting, see no idle-time command on page 18-5.
Syntax:
(config-pptps)# idle-time seconds
Field
Definition
seconds
Enter the maximum idle time for PPTP connection.
Range 0-99999 seconds, with a default of 1200.
Example: (config-pptps)# idle-time 1500
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
18-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPS Mode
no commands
no idle-time
Use the PPTP Server no idle-time command to reset the idle time to the default setting. To set the
maximum idle time for a PPTP connection, see idle-time command on page 18-4.
Syntax:
(config-pptps)# no idle-time
Example: (config-pptps)# no idle-time
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp authentication
Use the PPTP Server no ppp authentication command to disable PPP authentication. To enable
PPP authentication, see ppp authentication command on page 18-6.
Syntax:
(config-pptps)# no ppp authentication {chap|ms-chap|
ms-chapv2|pap}
Field
Definition
chap
Support Challenge Handshake Authentication (CHAP)
ms-chap
Support Microsoft CHAP (MS-CHAP).
ms-chapv2
Support Microsoft CHAP Version 2 (MS-CHAPv2).
pap
Support an unencrypted password. Default.
Example: (config-pptps)# no ppp authentication
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no ppp encryption
Use the PPTP Server no ppp encryption command to disable PPP encryption. To enable PPP
encryption, see ppp encryption command on page 18-6.
Syntax:
(config-pptps)# no ppp encryption {40-bit|128-bit|stateful}
Field
Definition
40-bit
MPPE-40 - Microsoft PPP encryption algorithm.
128-bit
MPPE-128 - Microsoft PPP encryption algorithm.
stateful
Enable the stateful state for encryption.
Example: (config-pptps)# no ppp encryption
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
18-5
Configuration - PPTPS Mode
no shutdown
Use the PPTP Server no shutdown command to set the admin state of the server up (in-service). To
set the admin state of the server down (out-of-service), see shutdown command on page 18-7.
Syntax:
(config-pptps)# no shutdown
Example: (config-pptps)# no shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp authentication
Use the PPTP Server ppp authentication command to configure the support of authentication types for
the password. To disable PPP authentication, see no ppp authentication command on page 18-5.
Syntax:
(config-pptps)# ppp authentication [chap|ms-chap|ms-chapv2|pap]
Field
Definition
chap
Support Challenge Handshake Authentication (CHAP)
ms-chap
Support Microsoft CHAP (MS-CHAP).
ms-chapv2
Support Microsoft CHAP Version 2 (MS-CHAPv2).
pap
Support an unencrypted password. Default.
Example: (config-pptps)# ppp authentication chap
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
ppp encryption
Use the PPTP Server ppp encryption command to configure the PPP encryption. To disable PPP
encryption, see no ppp encryption command on page 18-5.
Syntax:
(config-pptps)# ppp encryption {40-bit|128-bit|stateful}
Field
Definition
40-bit
MPPE-40 - Microsoft PPP encryption algorithm.
128-bit
MPPE-128 - Microsoft PPP encryption algorithm.
stateful
Enable the stateful state for encryption.
Example: (config-pptps)# ppp encryption stateful
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
18-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - PPTPS Mode
shutdown
Use the PPTP Server shutdown command to set the admin state of the server down (out-of-service). To
set the admin state up (in-service), see no shutdown command on page 18-6.
Syntax:
(config-pptps)# shutdown
Example: (config-pptps)# shutdown
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
start-address
Use the PPTP Server start-address command to set the PPTP remote host IP address range start.
Syntax:
(config-pptps)# start-address start-address
Field
Definition
start-ip-address
Enter the start IP address of the range.
Example: (config-pptps)# start-address 192.168.1.1
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
18-7
Configuration - PPTPS Mode
18-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
19
Configuration - RADIUS Mode
The RADIUS Configuration commands allow the user to configure the RADIUS parameters for each
interface.
This sub-group is entered with the (config)# radius-client command from the Configuration mode.
The RADIUS commands are represented by the (config-radius)# prompt.
RADIUS Commands
•
•
•
•
•
•
•
authentication
do
end
exit
history
host
key
Configuration - RADIUS Mode
authentication
Use the RADIUS authentication command to set the RADIUS client authentication method.
Syntax:
(config-radius)# authentication {chap|ms-chap|ms-chapv2|pap}
Field
Definition
chap
CHAP - Challenge Handshake Authentication
ms-chap
MS-CHAP - Microsoft CHAP
ms-chapv2
MS-CHAPv2 - Microsoft CHAP Version 2
pap
PAP - Unencrypted Password. Default
Example: (config-radius)# authentication chap
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
19-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - RADIUS Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
19-3
Configuration - RADIUS Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-radius)# end
Example: (config-radius)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-radius)# exit
Example: (config-radius)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-radius)# history
Example: (config-radius)# history
exit
authentication chap
host
host 192.168.1.1
key
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
19-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - RADIUS Mode
host
Use the RADIUS host command to set the RADIUS server IP address on the system.
Syntax:
(config-radius)# host address auth-port port
Field
Definition
address
Enter the IP address of the RADIUS server.
port
Enter the port number to use for RADIUS authentication. Range is 0 65535 with a default of 1812.
Example: (config-radius)# host 192.168.1.1 auth-port 1812
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
key
Use the RADIUS key command to set the RADIUS shared secret password.
Syntax:
(config-radius)# key password
Field
Definition
password
Enter a shared secret password for RADIUS, with a maximum of 8
characters.
Example: (config-radius)# key testpswd
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
19-5
Configuration - RADIUS Mode
19-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
20
Configuration - VLAN Mode
The VLAN Configuration commands allow the user to configure the global VLAN parameters.
This sub-group is entered with the (config)# vlan command from the Configuration mode.
The global VLAN commands are represented by the (config-vlan)# prompt.
VLAN (Global) Commands
• do
• end
• exit
• history
• no commands
• port-dot1q
• port-priority
• port-protocol-filter
• pvid
• tag-all
• vlan-feature
Configuration - VLAN Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
20-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - VLAN Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-vlan)# end
Example: (config-vlan)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-vlan)# exit
Example: (config-vlan)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-vlan)# history
Example: (config-vlan)# history
port-priority Ethernet 1.1 0
port-protocol-filter disable Ethernet 1.1
tag-port Ethernet 1.1
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
20-3
Configuration - VLAN Mode
no commands
no port-dot1q
Use the VLAN no port-dot1q command to disable dot1q tagging for the port. By default, VLAN
tagging is disabled on a LAN port. In this default state, if the port receives a VLAN tagged frame,
it will ignore the VLAN header and will process the ingress frames as a regular Ethernet frame. The
VLAN tag will not be altered.
Note: Ingress port is a port receiving frames from a source external to the switch. Egress port is a
port forwarding frames to another port(s) in the switch.
To set the port to VLAN aware mode, see port-dot1q command on page 20-5.
Syntax:
(config-vlan)# no port-dot1q ethernet port
Field
Definition
port
Ethernet port in the form {port}.{sub-interface}.
Adit 3104 and Adit 3200: 1.1, 1.2, 1.3, 1.4, 2.1
Adit 3500 and MSR: 1.1 and 2.1
Example: (config-vlan)# no port-dot1q ethernet 1.1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
no vlan
Use the VLAN no vlan command to clear a VLAN entry.
Syntax:
(config-vlan)# no vlan entry
Field
Definition
entry
VLAN entry. Range = 2 - 4094.
Example: (config-vlan)# no vlan 2
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
20-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - VLAN Mode
port-dot1q
Use the VLAN port-dot1q command to enable dot1q tagging for the port. If VLAN tagging is enabled
on a port, the port will forward any untagged or priority tagged frames with a VID equal to the ingress
port’s PVID and the priority of the tagged frame will remain unchanged. See the port-priority
command, on page 20-5, to set the priority of the port.
Note: Ingress port is a port receiving frames from a source external to the switch. Egress port is a port
forwarding frames to another port(s) in the switch.
To clear the dot1q for the port, see no port-dot1q command on page 20-4.
Syntax:
(config-vlan)# port-dot1q ethernet port
Field
Definition
port
Ethernet port in the form {port}.{sub-interface}.
Adit 3104 and Adit 3200: 1.1, 1.2, 1.3, 1.4, 2.1
Adit 3500 and MSR: 1.1 and 2.1
Example: (config-vlan)# port-dot1q ethernet 1.1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
port-priority
Use the VLAN port-priority command to set the VLAN priority for the port.
Syntax:
(config-vlan)# port-priority ethernet port priority
Field
Definition
port
Ethernet port in the form {port}.{sub-interface}.
Adit 3104 and Adit 3200: 1.1, 1.2, 1.3, 1.4, 2.1
Adit 3500 and MSR: 1.1 and 2.1
priority
Set priority level. Range = 0 - 7. Default is 0.
Example: (config-vlan)# port-priority ethernet 1.1 0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
20-5
Configuration - VLAN Mode
port-protocol-filter
Use the VLAN port-protocol-filter command to enable VLAN filtering for the port.
Note: The vlan-feature command, on page 20-7, must be executed before this command.
Syntax:
(config-vlan)# port-protocol-filter {disable|enable} ethernet
port
Field
Definition
disable
Disable VLAN filtering on defined Ethernet port.
enable
Enable VLAN filtering on defined Ethernet port.
port
Ethernet port in the form {port}.{sub-interface}.
Adit 3104 and Adit 3200: 1.1, 1.2, 1.3, 1.4, 2.1
Adit 3500 and MSR: 1.1 and 2.1
Example: (config-vlan)# port-protocol-filter enable ethernet 1.1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
pvid
Use the VLAN pvid command to set the port native VLAN ID, or PVID.
Syntax:
(config-vlan)# pvid ethernet port
Field
Definition
port
Ethernet port in the form {port}.{sub-interface}.
Adit 3104 and Adit 3200: 1.1, 1.2, 1.3, 1.4, 2.1
Adit 3500 and MSR: 1.1 and 2.1
Example: (config-vlan)# pvid ethernet 1.1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
20-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - VLAN Mode
tag-all
Use the VLAN tag-all command to enable dot1q tagging for all ports.
If VLAN tagging is enabled on all ports, an ingress port should forward any untagged or priority tagged
frames with a VID equal to the ingress port’s PVID and set the priority of the untagged frame to that of
the ingress port. The priority of the tagged frame remain unchanged. See the port-priority command, on
page 20-5, to set the priority of the port.
Note: Ingress port is a port receiving frames from a source external to the switch. Egress port is a port
forwarding frames to another port(s) in the switch.
Syntax:
(config-vlan)# tag-all {disable|enable}
Field
Definition
disable
Disable dot1q for all ports. Default.
enable
Enable dot1q for all ports.
Example: (config-vlan)# tag-all enable
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
vlan-feature
Use the VLAN mode vlan-feature command to enable/disable the VLAN feature on the device.
Note: This command is not visible on the Adit 3500 or MSR, as VLAN is always enabled on these
products.
Syntax:
(config-vlan)# vlan-feature {disable|enable}
Field
Definition
disable
Disable VLAN feature.
enable
Enable VLAN feature.
Example: (config-vlan)# vlan-feature enable
Supported Platforms: Adit 3104, Adit 3200
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
20-7
Configuration - VLAN Mode
20-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
21
Configuration - VLAN Port Mode
The VLAN Port Configuration commands allow the user to configure the VLAN port parameters.
This sub-group is entered with the (config)# vlan {vlan-id} command from the Configuration mode.
The VLAN Port commands are represented by the (config-vlan-{n})# prompt.
VLAN (Port) Commands
• do
• end
• exit
• history
• no commands
• port
• priority
• voip-interface
Configuration - VLAN Port Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
21-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - VLAN Port Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-vlan-{n})# end
Example: (config-vlan-100)# end
#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-vlan-{n})# exit
Example: (config-vlan-100)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-vlan-{n})# history
Example: (config-vlan-100)# history
port-priority Ethernet 1.1 0
port-protocol-filter disable Ethernet 1.1
tag-port Ethernet 1.1
history
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
21-3
Configuration - VLAN Port Mode
no commands
no port
Use the VLAN no port command to remove this port’s membership from the VLAN. To set the
preferences, see port command on page 21-4.
Syntax:
(config-vlan-{n})# no port ethernet port
Field
Definition
port
Ethernet port in the form {port}.{sub-interface}.
Adit 3104 and Adit 3200: 1.1, 1.2, 1.3, 1.4, 2.1
Adit 3500 and MSR: 1.1 and 2.1
Example: (config-vlan-100)# no port ethernet 1.1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500
no voip-interface
Use the VLAN no voip-interface command to clear VLAN tagging for the originating VoIP traffic.
Syntax:
(config-vlan-{n})# no voip-interface
Example: (config-vlan-100)# no voip-interface
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
port
Use the VLAN port command to set the Ethernet port as a VLAN port member.
Syntax:
(config-vlan-{n})# port ethernet port
Field
Definition
port
Ethernet port in the form {port}.{sub-interface}.
Adit 3104 and Adit 3200: 1.1, 1.2, 1.3, 1.4, 2.1
Adit 3500 and MSR: 1.1 and 2.1
Example: (config-vlan-100)# port ethernet 1.1
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
21-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - VLAN Port Mode
priority
Use the VLAN priority command to set the VLAN priority level.
Syntax:
(config-vlan-{n})# priority priority
Field
Definition
priority
Set priority level. Range = 0 - 7.
Example: (config-vlan-100)# priority 0
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
voip-interface
Use the VLAN voip-interface command to set the VLAN tagging for the originating VoIP traffic.
Syntax:
(config-vlan-{n})# voip-interface
Example: (config-vlan-100)# voip-interface
Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
21-5
Configuration - VLAN Port Mode
21-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
22
Configuration - Voice Port Mode
The Voice Port Configuration commands allow the user to configure the Voice Port parameters.
Enter this sub-group with the (config)# voice-port command from the Configuration mode.
The Voice Port commands are represented by the (config-vport)# prompt.
Note: There are two additional Voice Port groups (FXS-Chapter 23 and Trunk-Chapter 24), please see
their respective chapters for information.
Voice Port Commands
•
•
•
•
•
•
•
digit-map (global)
do
end
exit
history
no digit-map (global)
tos
Configuration - Voice Port Mode
digit-map (global)
Use the Voice Port digit-map global command to configure the Digit Map on a global level. To disable
digit map, see no digit-map (global) command on page 22-5.
Syntax:
(config-vport)# digit-map mode {long-timeout seconds |pattern
number pattern |short-timeout seconds}
Field
Definition
long-timeout
seconds
Range is 4-60 seconds, with a default of 16.
pattern
number - Enter pattern number to modify. Range is 1-30.
See show digit-map command on page 3-37, to display the current list
of Digit Map numbers.
pattern - Enter the new pattern, with a maximum of 30 characters.
short-timeout
seconds
Range is 1-10 seconds, with a default of 4.
Example: (config-vport)# digit-map mode long-timeout 20
Supported Platforms: Adit 3104, Adit 3500, MSR
22-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Port Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
22-3
Configuration - Voice Port Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-vport)# end
Example: (config-vport)# end
#
Supported Platforms: Adit 3104, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-vport)# exit
Example: (config-vport)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3500, MSR
history
Use the history command to display commands that have been entered in this session.
Syntax:
(config-vport)# history
Example: (config-vport)# history
tos sip 0fx6
tos sip value 0xff
digit-map long-timeout 10
history
Supported Platforms: Adit 3104, Adit 3500, MSR
22-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Port Mode
no digit-map (global)
Use the Voice Port no digit-map command to remove a digit map pattern. To configure digit map, see
digit-map (global) command on page 22-2.
Syntax:
(config-vport)# no digit-map pattern number
Field
Definition
pattern number
Enter pattern number to remove. Range is 1-30.
See show digit-map command on page 3-37, to display the current list
of Digit Map numbers.
Example: (config-vport)# no digit-map pattern 10
Supported Platforms: Adit 3104, Adit 3500, MSR
tos
Use the Voice Port tos command to set the Type of Service (ToS). This command sets the precedence
bits in the TOS byte of the IP header to prioritize packet handling.
Syntax:
(config-vport)# tos {rtp value hex-value|sip value hex-value}
Field
Definition
rtp value hex-value
Range is 0x00 - 0xff. Default 0xb8
sip value hex-value
Range is 0x00 - 0xff. Default 0xdc
Example: (config-vport)# tos rtp 0xb8
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
22-5
Configuration - Voice Port Mode
22-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
23
Configuration - Voice Port FXS Mode
The Voice Port FXS Configuration commands allow the user to configure the Voice Port FXS
parameters.
Enter this sub-group with the (config)# voice-port fxs number command from the Configuration mode.
The Voice Port FXS commands are represented by the (config-vport-fxs-{n})# prompt.
Voice Port FXS Commands
• comfort-noise
• description
• do
• echo-cancel
• end
• exit
• history
• input-gain
• no commands
• output-gain
• per-line-logging
• shutdown
• signal
Configuration - Voice Port FXS Mode
comfort-noise
Use the Voice Port FXS comfort-noise command to enable the comfort noise feature. To disable
comfort noise, see no comfort-noise command on page 23-6.
Syntax:
(config-vport-fxs-{n})# comfort-noise enable
Example: (config-vport-fxs-1)# comfort-noise enable
Supported Platforms: Adit 3104, Adit 3500, MSR
description
Use the Voice Port FXS description command to change the description of the voice port.
Syntax:
(config-vport-fxs-{n})# description text
Field
Definition
text
Enter a description for the port, with a maximum of 64 characters.
Example: (config-vport-fxs-1)# description VoiceP-#2
Supported Platforms: Adit 3104, Adit 3500, MSR
23-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Port FXS Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
23-3
Configuration - Voice Port FXS Mode
echo-cancel
Use the Voice Port FXS echo-cancel command to enable Echo Cancellation on this trunk. To to disable
Echo Cancellation, see no echo-cancel command on page 23-6
Syntax:
(config-vport-fxs-{n})# echo-cancel enable
Example: (config-vport-fxs-1)# echo-cancel enable
Supported Platforms: Adit 3104, Adit 3500, MSR
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file.
Syntax:
(config-vport-fxs-{n})# end
Example: (config-vport-fxs-1)# end
#
Supported Platforms: Adit 3104, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-vport-fxs-{n})# exit
Example: (config-vport-fxs-1)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3500, MSR
23-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Port FXS Mode
history
Use the history command to display commands that have been entered in this session.
Syntax:
(config-vport-fxs-{n})# history
Example: (config-vport-fxs-1)# history
description tests
echo-cancel enable
input-gain 4
output-gain 4
signal ground-start
history
Supported Platforms: Adit 3104, Adit 3500, MSR
input-gain
Use the Voice Port FXS input-gain command to set the gain on the receive side voice path for the
specified voice channel(s).
Syntax:
(config-vport-fxs-{n})# input-gain value
Field
Definition
value
Range -12 to +6dB. Default is 0.
Example: (config-vport-fxs-1)# input-gain 4
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
23-5
Configuration - Voice Port FXS Mode
no commands
no comfort-noise
Use the Voice Port FXS no comfort-noise command to disable comfort noise. To enable remote
access, see comfort-noise command on page 23-2.
Syntax:
(config-vport-fxs-{n})# no comfort-noise
Example: (config-vport-fxs-1)# no comfort-noise
Supported Platforms: Adit 3104, Adit 3500, MSR
no echo-cancel
Use the Voice Port FXS no echo-cancel command disable echo cancellation on this port. To enable
echo cancellation, see echo-cancel command on page 23-4.
Syntax:
(config-vport-fxs-{n})# no echo-cancel
Example: (config-vport-fxs-1)# no echo-cancel
Supported Platforms: Adit 3104, Adit 3500, MSR
no per-line-logging
Use the Voice Port FXS no per-line-logging command disable the logging per line feature. To
enable logging, see per-line-logging command on page 23-7.
Syntax:
(config-vport-fxs-{n})# no per-line-logging
Example: (config-vport-fxs-1)# no per-line-logging
Supported Platforms: Adit 3104, Adit 3500, MSR
no shutdown
Use the Voice Port FXS no shutdown command to set this voice port up (In-Service). To set this
port down (Out-of-Service), see shutdown command on page 23-7.
Syntax:
(config-vport-fxs-{n})# no shutdown
Example: (config-vport-fxs-1)# no shutdown
Supported Platforms: Adit 3104, Adit 3500, MSR
23-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Port FXS Mode
output-gain
Use the Voice Port FXS output-gain command to set the gain on the transmit side voice path for the
specified voice channel(s).
Syntax:
(config-vport-fxs-{n})# output-gain value
Field
Definition
value
Range -12 to +6dB. Default is 0.
Example: (config-vport-fxs-1)# output-gain 4
Supported Platforms: Adit 3104, Adit 3500, MSR
per-line-logging
Use the Voice Port FXS per-line-logging command to enable the logging per line feature. To to disable
logging, see no per-line-logging command on page 23-6
Syntax:
(config-vport-fxs-{n})# per-line-logging enable
Example: (config-vport-fxs-1)# per-line-logging enable
Supported Platforms: Adit 3104, Adit 3500, MSR
shutdown
Use the Voice Port FXS shutdown command to set this port down (Out-of-Service). To set this voice
port up (In-Service), see no shutdown command on page 23-6.
Syntax:
(config-vport-fxs-{n})# shutdown
Example: (config-vport-fxs-1)# shutdown
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
23-7
Configuration - Voice Port FXS Mode
signal
Use the Voice Port FXS signal command to set the signaling protocol.
Syntax:
(config-vport-fxs-{n})# signal {ground-start|loop-start}
Field
Definition
ground-start
Sets the line to Ground Start signaling
loop-start
Sets the line to Loop Start signaling
Example: (config-vport-fxs-1)# signal ground-start
Supported Platforms: Adit 3104, Adit 3500, MSR
23-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
24
Configuration - Voice Port Trunk Mode
The Voice Port Trunk Configuration commands allow the user to configure the Voice Port Trunk
parameters. Enter this sub-group with the (config)# voice-port trunk number command from the
Configuration mode. Note: The Trunk option is not supported on the Adit 3104 or the Adit 3200.
The Voice Port Trunk commands are represented by the (config-vport-trk-{n})# prompt.
Voice Port Trunk Commands
• comfort-noise
• connection lcc
• connection t1
• description
• digit-map
• do
• echo-cancel
• end
• exit
• history
• input-gain
• isdn switch-type (PRI)
• no commands
• output-gain
• registration
• signal
• trunk
Configuration - Voice Port Trunk Mode
comfort-noise
Use the Voice Port Trunk comfort-noise command to enable the comfort noise feature. To disable this
feature, see no comfort-noise command on page 24-8.
Syntax:
(config-vport-trk-{n})# comfort-noise enable
Example: (config-vport-trk-1)# comfort-noise enable
Supported Platforms: Adit 3500, MSR
connection lcc
Use the Voice Port Trunk connection lcc command to connect an MSR Link Cross Connect (LCC). To
disconnect this connection, see the no connection lcc command on page 24-8.
Syntax:
(config-vport-trk-{n})# connection lcc number
Field
Definition
number
Link Cross Connect. Range = 1-8.
Example: (config-vport-trk-1)# connection lcc 2
Supported Platforms: MSR
connection t1
Use the Voice Port Trunk connection t1 command to enter the T1 connection configuration mode. To
disconnect this connection, see no connection t1 command on page 24-8.
Syntax:
(config-vport-trk-{n})# connection t1 port
Field
Definition
port
T1 port range 1-4.
Example: (config-vport-trk-1)# connection t1 2
Supported Platforms: Adit 3500
24-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Port Trunk Mode
description
Use the Voice Port Trunk description command to change the description of the trunk.
Syntax:
(config-vport-trk-{n})# description text
Field
Definition
text
Enter a description for the trunk, with a maximum of 64 characters.
Example: (config-vport-trk-1)# description VoiceP-#4
Supported Platforms: Adit 3500, MSR
digit-map
Use the Voice Port Trunk digit-map command to configure the Digit Map on the trunk level. To disable
digit map, see no digit-map command on page 24-9.
Syntax:
(config-vport-trk-{n})# digit-map mode {default|custom}
Field
Definition
default
Pass dialed number as a complete number for routing to the phone
book, or to the proxy if there are no phone book entries.
custom
Process as for the default digit map.
Example: (config-vport-trk-1)# digit-map mode default
Supported Platforms: Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
24-3
Configuration - Voice Port Trunk Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
24-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Port Trunk Mode
echo-cancel
Use the Voice Port Trunk echo-cancel command to enable Echo Cancellation on this trunk. To disable
Echo Cancellation, see no echo-cancel command on page 24-9.
Syntax:
(config-vport-trk-{n})# echo-cancel enable
Example: (config-vport-trk-1)# echo-cancel enable
Supported Platforms: Adit 3500, MSR
end
Use the end command to exit the current Configuration mode.
Syntax:
(config-vport-trk-{n})# end
Example: (config-vport-trk-1)# end
#
Supported Platforms: Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-vport-trk-{n})# exit
Example: (config-vport-trk-1)# exit
(config)#
Supported Platforms: Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
24-5
Configuration - Voice Port Trunk Mode
history
Use the history command to display commands that have been entered in this session.
Syntax:
(config-vport-trk-1)# history
Example: (config-vport-trk-1)# history
exit
description VoiceP-#1
digit-map mode custom
history
Supported Platforms: Adit 3500, MSR
input-gain
Use the Voice Port Trunk input-gain command to set the gain on the receive side voice path for the
specified voice channel(s).
Syntax:
(config-vport-trk-{n})# input-gain value
Field
Definition
value
Range -12 to +6dB. Default is 0.
Example: (config-vport-trk-1)# input-gain 6
Supported Platforms: Adit 3500, MSR
24-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Port Trunk Mode
isdn switch-type (PRI)
Use the Voice Port Trunk isdn switch-type command to configure the switching type (protocol) on this
trunk. Note: Hunt sequence of the PRI is a Round-Robin type, and is not configurable.
Syntax:
(config-vport-trk-{n})# isdn switch-type {pri-dms100|pri-4ess
|pri-5ess|pri-ni2}
Field
Definition
pri-4ess
PRI-4ess - The class 4 US AT&T proprietary version of ISDN.
pri-5ess
PRI-5ess - The class 5 ISDN central office circuit switching system
developed by AT&T
pri-dms100
PRI-dms100 - Digital central office switch (number 100) from
Northern Telecom.
pri-ni2
PRI-ni2 - This is the CCITT National ISDN 2 PRI standard.
Example: (config-vport-trk-1)# isdn switch-type pri-ni2
Supported Platforms: Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
24-7
Configuration - Voice Port Trunk Mode
no commands
no comfort-noise
Use the Voice Port Trunk no comfort-noise command to disable comfort noise. To enable remote
access, see comfort-noise command on page 24-2.
Syntax:
(config-vport-trk-{n})# no comfort-noise
Example: (config-vport-trk-1)# no comfort-noise
Supported Platforms: Adit 3500, MSR
no connection lcc
Use the Voice Port Trunk no connection lcc command to remove a Link Cross Connection (LCC).
To add an LCC, see the connection lcc command on page 24-2.
Syntax:
(config-vport-trk-{n})# no connection lcc number
Field
Definition
number
Enter a current LCC connection. Range = 1-8.
Example: (config-vport-trk-1)# no connection lcc 2
Supported Platforms: MSR
no connection t1
Use the Voice Port Trunk no connection t1 command to remove a T1 connection. To enter the T1
connection configuration mode, see connection t1 command on page 24-2.
Syntax:
(config-vport-trk-{n})# no connection t1 port
Field
Definition
port
Enter a current T1 connection. T1 port range 1-4.
Example: (config-vport-trk-1)# no connection t1 2
Supported Platforms: Adit 3500
24-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Port Trunk Mode
no digit-map
Use the Voice Port Trunk no digit-map command to disable digit map on the trunk. To configure
digit map, see digit-map command on page 24-3.
Syntax:
(config-vport-trk-{n})# no digit-map
Example: (config-vport-trk-1)# no digit-map
Supported Platforms: Adit 3500, MSR
no echo-cancel
Use the Voice Port Trunk no echo-cancel command disable echo cancellation on this port. To
enable echo cancellation, see echo-cancel command on page 24-5.
Syntax:
(config-vport-trk-{n})# no echo-cancel
Example: (config-vport-trk-1)# no echo-cancel
Supported Platforms: Adit 3500, MSR
no registration enable
Use the Voice Port Trunk no registration enable command disable trunk registration. To enable
registration, see registration enable command on page 24-12.
Syntax:
(config-vport-trk-{n})# no registration enable
Example: (config-vport-trk-1)# no registration enable
Supported Platforms: Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
24-9
Configuration - Voice Port Trunk Mode
no registration line
Use the Voice Port Trunk no registration line command remove a registration line. To add a
registration line, see registration line enable command on page 24-13.
Syntax:
(config-vport-trk-{n})# no registration line number
Field
Definition
number
Enter line number to Remove. Range 1 -300. Note: This line must be
enabled for this command to be accepted.
Example: (config-vport-trk-1)# no registration line 1
Supported Platforms: Adit 3500, MSR
no registration line enable
Use the Voice Port Trunk no registration line enable command to disable a registration line. To
enable line registration, see registration line enable command on page 24-13.
Syntax:
(config-vport-trk-{n})# no registration line number enable
Field
Definition
number
Enter line number to disable. Range 1 -300. Note: This line must be
enabled for this command to be accepted.
Example: (config-vport-trk-1)# no registration line 1 enable
Supported Platforms: Adit 3500, MSR
no registration line logging
Use the Voice Port Trunk no registration line logging command disable line logging on a PBX
line. To enable logging, see registration line logging command on page 24-14.
Syntax:
(config-vport-trk-{n})# no registration line number logging
Field
Definition
number
Enter line number to disable. Range 1 -300.
Example: (config-vport-trk-1)# no registration line 1 logging
Supported Platforms: Adit 3500, MSR
24-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Port Trunk Mode
output-gain
Use the Voice Port Trunk output-gain command to set the gain on the transmit side voice path for the
specified voice channel(s).
Syntax:
(config-vport-trk-{n})# output-gain value
Field
Definition
value
Range -12 to +6dB. Default is 0.
Example: (config-vport-trk-1)# output-gain 6
Supported Platforms: Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
24-11
Configuration - Voice Port Trunk Mode
registration
The registration command enables the user to Add, Edit, Remove, Enable, Disable PBX line number
behind a voice trunk that will register to the SIP proxy.
registration enable
Use the Voice Port Trunk registration enable command to enable the Voice Port registration
feature. To disable Voice Port registration, see no registration enable command on page 24-9.
Syntax:
(config-vport-trk-{n})# registration enable
Example: (config-vport-trk-1)# registration enable
Supported Platforms: Adit 3500, MSR
registration line authentication
Use the Voice Port Trunk registration line authentication command to configure the username to
authenticate.
Syntax:
(config-vport-trk-{n})# registration line value line-numbers
value authentication {phone-number|username username} password
password
Field
Definition
line value
Enter the PBX line number to configure. Range is 1 - 300.
line-numbers value Define the number of lines in this block that are going to be registered.
Starting from the first-phone-number, increased by 1 each.
phone-number
Set the phone number to authenticate.
username username Set the user name to authenticate.
password
Enter a password for the authentication.
Example: (config-vport-trk-1)# registration line 1 line-numbers 3
authentication phone-number password hello
Supported Platforms: Adit 3500, MSR
24-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Port Trunk Mode
registration line enable
Use the Voice Port Trunk registration line enable command to enable registration. To disable
registration, see no registration line enable command on page 24-10.
Syntax:
(config-vport-trk-{n})# registration line value line-numbers
value enable
Field
Definition
line value
Enter the PBX line number to configure. Range is 1 - 300.
line-numbers value Define the number of lines in this block that are going to be registered.
Starting from the first-phone-number, increased by 1 each.
Example: (config-vport-trk-1)# registration line 4 line-numbers 3 enable
Supported Platforms: Adit 3500, MSR
registration line first-phone-number
Use the Voice Port Trunk registration line first-phone-number command to define the first
number in a block that will be registered.
Syntax:
(config-vport-trk-{n})# registration line value line-numbers
value first-phone-number phone-number description description
Field
Definition
line value
Enter the PBX line number to configure. Range is 1 - 300.
line-numbers value Define the number of lines in this block that is going to be registered.
Starting from the first-phone-number, increased by 1 each.
phone-number
Enter the first number in a block that will be registered.
description
Enter a description with a maximum of 20 characters.
Example: (config-vport-trk-1)# registration line 1 line-numbers 3
first-phone-number 3032185555 description turin
Supported Platforms: Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
24-13
Configuration - Voice Port Trunk Mode
registration line logging
Use the Voice Port Trunk registration line authentication command to enable logging on this line.
To disable logging, see no registration line logging command on page 24-10.
Syntax:
(config-vport-trk-{n})# registration line value line-numbers
value logging
Field
Definition
line value
Enter the PBX line number to configure. Range is 1 - 300.
line-numbers value Define the number of lines in this block that is going to be registered.
Starting from the first-phone-number, increased by 1 each.
Example: (config-vport-trk-1)# registration line 4 line-numbers 3 logging
Supported Platforms: Adit 3500, MSR
signal
Use the Voice Port Trunk signal command to configure the trunk signal type for a CAS trunk.
Syntax:
(config-vport-trk-{n})# signal {delay-dial|immediate|
wink-start}
Field
Definition
delay-dial
Set the trunk to CAS Delay Dial signaling.
immediate
Set the trunk to CAS Immediate Start signaling.
wink-start
Set the trunk to CAS Wink Start signaling.
Example: (config-vport-trk-1)# signal immediate
Supported Platforms: Adit 3500, MSR
24-14
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Port Trunk Mode
trunk
Use the Voice Port Trunk trunk command to set the Trunk ID.
Syntax:
(config-vport-trk-{n})# trunk trunk-id
Field
Definition
trunk-id
Enter a trunk ID. Maximum of 20 characters.
Example: (config-vport-trk-1)# trunk VPtrunk1
Supported Platforms: Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
24-15
Configuration - Voice Port Trunk Mode
24-16
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
CHAPTER
25
Configuration - Voice Service SIP Mode
The Voice Service SIP Configuration commands allow the user to configure the Voice Trunk SIP
parameters.
Enter this sub-group with the (config)# voice-service sip command from the Configuration mode.
The Voice Port commands are represented by the (config-voice-serv-sip)# prompt.
Voice Service SIP Commands
• calling-party-disc
• privacy-mode
• conference
• proxy-server
• do
• proxy-type
• dtmf
• redundancy advance-retries
• early-media
• redundancy advance-timeout
• end
• redundancy filter-incoming
• exit
• redundancy primary-address
• fax-protocol-t38 ecs
• redundancy rollback-timer
• fax-protocol-t38 redundancy • redundancy secondary-address
• fax-protocol-t38 signaling
• redundancy ttl
• feature-mode
• redundancy type
• gateway-ip
• registration
• history
• rtp-base-port
• no commands
• session-timer
• outbound-proxy
• sip-port
• phone-number
• transport
• prack
Configuration - Voice Service SIP Mode
calling-party-disc
Use the Voice Service SIP calling-party-disc command to configure the call party disconnect feature.
Syntax:
(config-voice-serv-sip)# calling-party-disc duration
Field
Definition
duration
Range 500 - 3000 ms.
Example: (config-voice-serv-sip)# calling-party-disc 600
Supported Platforms: Adit 3104, Adit 3500, MSR
conference
Use the Voice Service SIP conference command to enable the conference calling feature. To disable
conference, see no conference command on page 25-9.
Syntax:
(config-voice-serv-sip)# conference enable
Example: (config-voice-serv-sip)# conference enable
Supported Platforms: Adit 3104, Adit 3500, MSR
25-2
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Service SIP Mode
do
Use the do commands to run User and Privileged mode commands. The following are links to the User
and Privileged do commands.
User Mode Commands
date command, on page 2-2
enable command, on page 2-2
end command, on page 2-2
exit command, on page 2-3
help command, on page 2-3
history command, on page 2-4
ping command, on page 2-5
show command, on page 2-6
traceroute command, on page 2-33
Privileged Mode Commands
clear command, on page 3-2
configure terminal command, on page 3-3
copy command, on page 3-3
date command, on page 3-4
debug command, on page 3-5
end command, on page 3-12
exit command, on page 3-12
help command, on page 3-13
history command, on page 3-14
log clear command, on page 3-15
no debug command, on page 3-16
ping command, on page 3-17
reload command, on page 3-18
show command, on page 3-19
traceroute command, on page 3-67
upgrade command, on page 3-67
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
25-3
Configuration - Voice Service SIP Mode
dtmf
Use the Voice Service SIP dtmf command to configure the DTMF events.
Syntax:
(config-voice-serv-sip)# dtmf {inband|rfc2833}
Field
Definition
inband
Configure the DTMF in-band, as part of the RTP packets.
rfc2833
Configure the DTMF events out-of-band, as RTP event packets.
Example: (config-voice-serv-sip)# dtmf inband
Supported Platforms: Adit 3104, Adit 3500, MSR
early-media
Use the Voice Service SIP early-media command to configure the SIP early media. Early Media is the
ability of two SIP user agents to communicate before a SIP call is actually established. Support for early
media is important largely for interoperability with the PSTN.
Syntax:
(config-voice-serv-sip)# early-media {auto|180|183}
Field
Definition
auto
Send 180/183, based on if in-band call progress tones are available.
180
The 180 Ringing message is a provisional or informational response
used to indicate that the INVITE message has been received by the
user agent and that alerting is taking place.
183
The 183 Session Progress response indicates that information about
the call state is present in the message body media information.
Note: Both 180 and 183 messages may contain SDP which allow an
early media session to be established prior to the call being answered.
Example: (config-voice-serv-sip)# early-media auto
Supported Platforms: Adit 3500, MSR
25-4
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Service SIP Mode
end
Use the end command to exit the current configuration mode, and must be used to mark the end of any
configuration file. This command can be entered in any configuration mode with the same result.
Syntax:
(config-voice-serv-sip)# end
Example: (config-voice-serv-sip)# end
#
Supported Platforms: Adit 3104, Adit 3500, MSR
exit
Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you
to the next higher level (example: back to Privileged mode from Interface configuration mode).
Syntax:
(config-voice-serv-sip)# exit
Example: (config-voice-serv-sip)# exit
(config)#
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
25-5
Configuration - Voice Service SIP Mode
fax-protocol-t38 ecs
Use the Voice Service SIP fax-protocol-t38 ecs command to configure the fax Error Correction
Scheme parameter.
Note: For the MSR, T.38 will be supported in a future release.
Syntax:
(config-voice-serv-sip)# fax-protocol-t38 ecs {none|redundant}
Example: (config-voice-serv-sip)# fax-protocol-t38 ecs redundant
Syntax Descriptions:
Variable
Definition
none
Set error correction to none.
redundant
Set error correction to redundant. Default.
Supported Platforms: Adit 3104, Adit 3500, MSR
fax-protocol-t38 redundancy
Use the Voice Service SIP fax-protocol-t38 redundancy command to set the T.38 protocol high and
low speed redundancy.
Note: For the MSR, T.38 will be supported in a future release.
Syntax:
(config-voice-serv-sip)# fax-protocol-t38 {hs-redundancy
value}|ls-redundancy value}
Example: (config-voice-serv-sip)# fax-protocol-t38 hs-redundancy 1
Syntax Descriptions:
Variable
Definition
hs-redundancy
Configures the number of duplicate packets to transmit during a high-speed
T.38 fax call. Note: Setting the HS Redundancy to greater than 0 will cause a
significant increase in the network bandwidth consumed by the fax call.
Range 0-3 packets, with a default of 0 packets (no redundancy).
ls-redundancy
Configures the number of duplicate packets to transmit during a
low-speed T.38 fax call machine protocol.
Range 0 to 4 packets (0 = no redundancy), with a default of 3 packets.
Supported Platforms: Adit 3104, Adit 3500, MSR
25-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Service SIP Mode
fax-protocol-t38 signaling
Use the Voice Service SIP fax-protocol-t38 signaling command to configure fax signaling.
Note: For the MSR, T.38 will be supported in a future release.
Syntax:
(config-voice-serv-sip)# fax-protocol-t38 signaling
{nse-only|nse-preferred|sdp-only|sdp-preferred}
Example: (config-voice-serv-sip)# fax-protocol-t38 signaling
sdp-preferred
Syntax Descriptions:
Variable
Definition
nse-only
Named Service Element (NSE) will be the only method tried without any
attempt to try alternate signaling method to establish connection if it fails.
sdp-only
Session Description Protocol (SDP) will be the only method tried without any
attempt to try alternate signaling method to establish connection if it fails.
nse-preferred
Named Service Element (NSE) preferred will be the first method tried with an
attempt to try the alternate SDP signaling method to connect if it fails.
sdp-preferred
Session Description Protocol (SDP) preferred will be the first method tried
with an attempt to try the alternate NSE signaling method to connect if it fails.
Default.
Supported Platforms: Adit 3104, Adit 3500, MSR
feature-mode
Use the Voice Service SIP feature-mode command to determine where the intelligence for the calling
features will lie, offering a choice between server-based (Info) and device-based (local) features.
Syntax:
(config-voice-serv-sip)# feature-mode {info|local}
Field
Definition
info
This selection is used with BroadSoft 11.1 Info Mode Proxy. Note: On
a BroadSoft server, the Adit device must be configured as “Generic
SIP Standard (Proxy Address)”.
local
Default is Local.
Example: (config-voice-serv-sip)# feature-mode info
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
25-7
Configuration - Voice Service SIP Mode
gateway-ip
Use the Voice Service SIP gateway-ip command to set the IP address to be used as the source IP for
VoIP.
Syntax:
(config-voice-serv-sip)# gateway-ip address
Field
Definition
address
The IP address to be used as the source IP for VoIP services when it
matches one of our up or running interfaces’ IP addresses, otherwise
our VoIP source IP address is determined by the previous automatic
algorithm.
Example: (config-voice-serv-sip)# gateway-ip 10.10.2.1
Supported Platforms: Adit 3104, Adit 3500, MSR
history
Use the history command to display commands that have been entered in this session. This command
can be entered in any configuration mode.
Syntax:
(config-voice-serv-sip)# history
Example: (config-voice-serv-sip)# history
feature-mode
outbound-proxy
outbound-proxy ip-address 192.168.2.2
dtmf inband
outbound-proxy 192.168.1.140
proxy
proxy-server 10.10.0.1
exit
history
Supported Platforms: Adit 3104, Adit 3500, MSR
25-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Service SIP Mode
no commands
no conference
Use the Voice Service SIP no conference command to disable the conference feature. To enable
conference, see conference command on page 25-2.
Syntax:
(config-voice-serv-sip)# no conference
Example: (config-voice-serv-sip)# no conference
Supported Platforms: Adit 3104, Adit 3500, MSR
no outbound-proxy
Use the Voice Service SIP no outbound-proxy command to disable the outbound proxy. To enable
outbound proxy, see outbound-proxy command on page 25-11.
Syntax:
(config-voice-serv-sip)# no outbound-proxy
Example: (config-voice-serv-sip)# no outbound-proxy
Supported Platforms: Adit 3104, Adit 3500, MSR
no prack
Use the Voice Service SIP no prack command to disable PRACK. To enable PRACK, see prack
command on page 25-11.
Syntax:
(config-voice-serv-sip)# no prack
Example: (config-voice-serv-sip)# no prack
Supported Platforms: Adit 3104, Adit 3500, MSR
no proxy-server
Use the Voice Service SIP no proxy-server command to disable proxy server. To enable proxy
server, see proxy-server command on page 25-12.
Syntax:
(config-voice-serv-sip)# no proxy-server
Example: (config-voice-serv-sip)# no proxy-server
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
25-9
Configuration - Voice Service SIP Mode
no redundancy filter-incoming
Use the Voice Service SIP no redundancy-filter-incoming command to disable the incoming
redundancy filter. To enable filter, see redundancy filter-incoming command on page 25-14.
Syntax:
(config-voice-serv-sip)# no redundancy filter-incoming
Example: (config-voice-serv-sip)# no redundancy filter-incoming
Supported Platforms: Adit 3104, Adit 3500, MSR
no redundancy rollback-timer
Use the Voice Service SIP no redundancy rollback-timer command to disable the redundancy
rollback timer. To enable timer, see redundancy rollback-timer command on page 25-15.
Syntax:
(config-voice-serv-sip)# no redundancy rollback-timer
Example: (config-voice-serv-sip)# no redundancy rollback-timer
Supported Platforms: Adit 3104, Adit 3500, MSR
no registration ignore-negotiated
Use the Voice Service SIP no registration ignore-negotiated command to disable ignore
negotiated expiration timeout. To enable ignore negotiated expiration timeout, see registration
command on page 25-17.
Syntax:
(config-voice-serv-sip)# no registration ignore-negotiated
Example: (config-voice-serv-sip)# no registration ignore-negotiated
Supported Platforms: Adit 3104, Adit 3500, MSR
no session-timer mode
Use the Voice Service SIP no session-timer mode command to disable the session timer mode. To
enable session timer mode, see session-timer command on page 25-18.
Syntax:
(config-voice-serv-sip)# no session-timer mode
Example: (config-voice-serv-sip)# no session-timer mode
Supported Platforms: Adit 3104, Adit 3500, MSR
25-10
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Service SIP Mode
outbound-proxy
Use the Voice Service SIP outbound-proxy command to configure the SIP outbound proxy. To disable
outbound proxy, see no outbound-proxy command on page 25-9.
Syntax:
(config-voice-serv-sip)# outbound-proxy {hostname hostname|
ip-address address}
Field
Definition
hostname
Enter the host name of the outbound proxy.
address
Enter the IP address of the outbound proxy.
Example: (config-voice-serv-sip)# outbound-proxy ip-address
192.168.1.140
Supported Platforms: Adit 3104, Adit 3500, MSR
phone-number
Use the Voice Service SIP phone-number command to configure the phone number maximum size.
Syntax:
(config-voice-serv-sip)# phone-number max-size number
Field
Definition
number
Enter the maximum size for the phone number. Range 3 - 24.
Example: (config-voice-serv-sip)# phone-number max-size 11
Supported Platforms: Adit 3104, Adit 3500, MSR
prack
Use the Voice Service SIP prack command to enable Provisional Acknowledgement (PRACK), as per
RFC 3262. To disable PRACK, see no prack command on page 25-9.
Syntax:
(config-voice-serv-sip)# prack enable
Example: (config-voice-serv-sip)# prack enable
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
25-11
Configuration - Voice Service SIP Mode
privacy-mode
Use the Voice Service SIP privacy-mode command to configure the SIP privacy mode.
Syntax:
(config-voice-serv-sip)# privacy-mode {none|rfc3325}
Field
Definition
none
Disables the Privacy Mode. Default is None.
rfc3325
Enables support for RFC 3325, as supported on the Sylantro
Application Server.
Example: (config-voice-serv-sip)# privacy-mode none
Supported Platforms: Adit 3104, Adit 3500, MSR
proxy-server
Use the Voice Service SIP proxy-server command to configure the SIP proxy server. To disable Proxy
server, see no proxy-server command on page 25-9.
Syntax:
(config-voice-serv-sip)# proxy-server {hostname hostname|
ip-address address}
Field
Definition
hostname
Enter the host name of the SIP proxy server, with a maximum number
of 20 characters (including the port if entered).
address
Enter the IP address of the SIP proxy server.
Example: (config-voice-serv-sip)# proxy-server 192.167.1.200
Supported Platforms: Adit 3104, Adit 3500, MSR
25-12
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Service SIP Mode
proxy-type
Use the Voice Service SIP proxy-type command to configure the SIP proxy type.
Syntax:
(config-voice-serv-sip)# proxy-type {broadsoft-info|generic|
sylantro}
Field
Definition
broadsoft-info
Sets the SIP proxy type to BroadSoft.
generic
Sets the SIP proxy type to generic.
sylantro
Sets the SIP proxy type to Sylantro.
Example: (config-voice-serv-sip)# proxy-type generic
Supported Platforms: Adit 3104, Adit 3500, MSR
redundancy advance-retries
Use the Voice Service SIP redundancy advance-retries command to set the number of retries before
a proxy is considered unreachable and moves onto the next.
Syntax:
(config-voice-serv-sip)# redundancy advance-retries number
Field
Definition
number
Range is 0 - 10, with a default of 3.
Example: (config-voice-serv-sip)# redundancy advance-retries 5
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
25-13
Configuration - Voice Service SIP Mode
redundancy advance-timeout
Use the Voice Service SIP redundancy advance-timeout command to set the interval of time before
moving onto the next proxy, when the first is not reachable.
Syntax:
(config-voice-serv-sip)# redundancy advance-timeout number
Field
Definition
number
Range 0 - 10 seconds, with a default of 2.
Example: (config-voice-serv-sip)# redundancy advance-timeout 5
Supported Platforms: Adit 3104, Adit 3500, MSR
redundancy filter-incoming
Use the Voice Service SIP redundancy filter-incoming command to enable filtering of packets from
unknown SIP servers. To filtering, see no redundancy filter-incoming command on page 25-10.
Syntax:
(config-voice-serv-sip)# redundancy filter-incoming enable
Example: (config-voice-serv-sip)# redundancy filter-incoming enable
Supported Platforms: Adit 3104, Adit 3500, MSR
redundancy primary-address
Use the Voice Service SIP redundancy primary-address command to configure the primary outbound
proxy.
Syntax:
(config-voice-serv-sip)# redundancy primary-address address
Field
Definition
address
Enter the IP address of the primary outbound proxy.
Example: (config-voice-serv-sip)# redundancy primary-address
192.168.100.140
Supported Platforms: Adit 3104, Adit 3500, MSR
25-14
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Service SIP Mode
redundancy rollback-timer
Use the Voice Service SIP redundancy rollback-timer command to set the interval of time between
the time the primary proxy fails, and when a rollback is performed back to the primary proxy. To disable
rollback timer, see no redundancy rollback-timer command on page 25-10.
Syntax:
(config-voice-serv-sip)# redundancy rollback-timer number
Field
Definition
number
Range 60 - 3600 seconds, or 0 (disabled), with a default of 300
(5 min).
Example: (config-voice-serv-sip)# redundancy rollback-timer 300
Supported Platforms: Adit 3104, Adit 3500, MSR
redundancy secondary-address
Use the Voice Service SIP redundancy secondary-address command to configure the secondary
outbound proxy.
Syntax:
(config-voice-serv-sip)# redundancy secondary-address address
Field
Definition
address
Enter the IP address of the secondary outbound proxy.
Example: (config-voice-serv-sip)# redundancy secondary-address
192.168.100.140
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
25-15
Configuration - Voice Service SIP Mode
redundancy ttl
Use the Voice Service SIP redundancy ttl command to set the set the SRV Time To Live (TTL) option.
The TTL is a set interval of time between flushing the SRV cache.
Syntax:
(config-voice-serv-sip)# redundancy ttl seconds
Field
Definition
seconds
Range 0 - 3600 seconds, with a default of 3600.
Example: (config-voice-serv-sip)# redundancy ttl 900
Supported Platforms: Adit 3104, Adit 3500, MSR
redundancy type
Use the Voice Service SIP redundancy type command to configure the redundancy type.
Syntax:
(config-voice-serv-sip)# redundancy type {none|srv|user}
Field
Definition
none
Redundancy feature is disabled. Default.
srv
An SRV lookup will be performed using the main proxy. The hosts/
IPs found are used to form the proxy redundancy list.
user
The SIP messages will be sent to the primary proxy. If there is a failure
it will be sent to the secondary proxy.
Example: (config-voice-serv-sip)# redundancy type none
Supported Platforms: Adit 3104, Adit 3500, MSR
25-16
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Service SIP Mode
registration
Use the Voice Service SIP registration command to configure the SIP registration, which allows trunk
registration for each user of a PBX. To disable ignore negotiated registration timeout, see no
registration ignore-negotiated command on page 25-10.
Syntax:
(config-voice-serv-sip)# registration {expire seconds|
failed-time seconds|ignore-negotiated enable|rate value|
retry-timeout milliseconds|tries value|window-size value}
Field
Definition
expire seconds
Sets the registration expire timeout. Range is 60 - 86400 seconds, with
a default of 3600.
failed-time seconds Sets the failed registration timer. Range is 30 - 86400 seconds, with a
default of 60.
ignore-negotiated
enable
Enable ignore negotiated expiration timeout.
rate value
Sets the number of registrations per minute. Range is 1-300, with a
default of 60.
retry-timeout
milliseconds
Sets the SIP retry timeout (SIP T1). Range is 200 - 5000 milliseconds,
with a default of 500.
tries value
Range is 1 - 10 times, with a default of 5.
window-size value
Range is 1 - 304 , with a default of 10.
Example: (config-voice-serv-sip)# registration expire 5000
Supported Platforms: Adit 3104, Adit 3500, MSR
rtp-base-port
Use the Voice Service SIP rtp-base-port command to configure the RTP base port. Choice of port to
be advertised during the media-negotiation phase of call setup and used during the call to send and
receive RTP.
Syntax:
(config-voice-serv-sip)# rtp-base-port number
Field
Definition
number
Range 1026 - 65000, with a default of 28000.
Example: (config-voice-serv-sip)# rtp-base-port 2500
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
25-17
Configuration - Voice Service SIP Mode
session-timer
session-timer mode
Use the Voice Service SIP session-timer mode command to configure the timer mode. To disable
the timer mode, see no session-timer mode command on page 25-10.
Syntax:
(config-voice-serv-sip)# session-timer mode
{requested|supported}
Field
Definition
requested
System shall initiate Session Timer procedures in outgoing initial
INVITE’s by including a Session-Expires header.
supported
System will respond to a Session-Expires request from a remote proxy
or UAC.
Example: (config-voice-serv-sip)# session-timer mode requested
Supported Platforms: Adit 3104, Adit 3500, MSR
session-timer refresher
Use the Voice Service SIP session-timer refresher command to configure the refresher timer.
Syntax:
(config-voice-serv-sip)# session-timer refresher {none|uac|uas}
Field
Definition
none
No refresher parameter shall be sent in an INVITE, and any refresher
received from the remote proxy or UAC shall be echoed back.
uac
User Agent Client. Default is UAC.
uas
User Agent Server.
Example: (config-voice-serv-sip)# session-timer refresher uas
Supported Platforms: Adit 3104, Adit 3500, MSR
25-18
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Configuration - Voice Service SIP Mode
session-timer timeout
Use the Voice Service SIP session-timer timeout command to configure the interval of idle time
to pass before timeout.
Syntax:
(config-voice-serv-sip)# session-timer timeout seconds
Field
Definition
seconds
Range 90 - 7200 seconds, with a default of 1800.
Example: (config-voice-serv-sip)# session-timer timeout 2500
Supported Platforms: Adit 3104, Adit 3500, MSR
sip-port
Use the Voice Service SIP sip-port command to select a TCP or UDP port to receive SIP traffic.
Syntax:
(config-voice-serv-sip)# sip-port port
Field
Definition
port
Range 1026 - 65535, default is 5060
Example: (config-voice-serv-sip)# sip-port 2500
Supported Platforms: Adit 3104, Adit 3500, MSR
transport
Use the Voice Service SIP transport command to configure the transport layer protocol to be used for
carrying SIP payloads. Note: UDP is commonly used and is the default.
Syntax:
(config-voice-serv-sip)# transport {tcp|udp}
Field
Definition
tcp
Transmission Control Protocol.
udp
User Datagram Protocol
Example: (config-voice-serv-sip)# transport udp
Supported Platforms: Adit 3104, Adit 3500, MSR
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
25-19
Configuration - Voice Service SIP Mode
25-20
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
INDEX
Index
A
access lan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
access wan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
access-control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
access-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
add user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-63
aggressive-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2
area authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-2
area stub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-2
ARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
authentication . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2, 19-2
authentication login . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
B
block-out-caller-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
C
calling-party-disc . . . . . . . . . . . . . . . . . . . . . . . . 8-2, 25-2
call-wait-caller-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
call-waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
clear
arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
caclkcd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
ip ospf process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2, 3-4
clock source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
codec preference . . . . . . . . . . . . . . . . . . . . . . . . . 8-3, 9-2
comfort-noise . . . . . . . . . . . . . . . . . . . . . . . . . . 23-2, 24-2
Command Line Interface Help . . . . . . . . . . . . . . . . . . . 1-5
compatible rfc1583 . . . . . . . . . . . . . . . . . . . . . . . . . . 16-3
conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-2
Configuration Access Commands
controller lcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
controller t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
DHCP pool ethernet . . . . . . . . . . . . . . . . . . . . . . . . 4-25
dial-peer voice pots fxs . . . . . . . . . . . . . . . . . . . . . 4-11
dial-peer voice pots trunk . . . . . . . . . . . . . . . . . . . 4-11
dial-peer voice voip . . . . . . . . . . . . . . . . . . . . . . . . 4-12
interface ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
interface multilink . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
interface serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
ipsec vpn_ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
l2tpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
pptpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53
pptps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53
radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-54
vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-63
vlan port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-64
voice-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65
voice-port-fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65
voice-port-trunk . . . . . . . . . . . . . . . . . . . . . . . . . . 4-66
voice-service-sip . . . . . . . . . . . . . . . . . . . . . . . . . . 4-66
Configuration Mode
access lan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
access wan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
access-control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
access-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
authentication login . . . . . . . . . . . . . . . . . . . . . . . . 4-6
clock source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
controller lcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
controller t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
date
auto-time-update . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
summer-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
timezone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
delete local-server . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
dial-peer
pots
fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
voip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
dmz-host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
dynamic-dns
backup-mx . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
mail-exchanger . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
offline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
wildcard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
host-filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
interface
ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
multilink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
ip
dhcp pool ethernet . . . . . . . . . . . . . . . . . . . . . . 4-25
Index
domain-name . . . . . . . . . . . . . . . . . . . . . . . . . .
host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ipsec authentication-retries . . . . . . . . . . . . . . . .
ipsec key generate key . . . . . . . . . . . . . . . . . . .
ipsec log ike . . . . . . . . . . . . . . . . . . . . . . . . . . .
ipsec log ipsec . . . . . . . . . . . . . . . . . . . . . . . . . .
ipsec vpn_ipsec . . . . . . . . . . . . . . . . . . . . . . . . .
net-to-host ipsec . . . . . . . . . . . . . . . . . . . . . . . .
net-to-net ipsec . . . . . . . . . . . . . . . . . . . . . . . . .
replay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
l2tpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
local-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
log
lcc
buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
notify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
pri . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
security
buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
notify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
sip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
system
buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
notify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
t1
buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
notify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mail-server
authentication enable . . . . . . . . . . . . . . . . . . . .
from-address . . . . . . . . . . . . . . . . . . . . . . . . . . .
host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
nat-bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
network-object . . . . . . . . . . . . . . . . . . . . . . . . . . .
no
access lan . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
access wan . . . . . . . . . . . . . . . . . . . . . . . . . . . .
access-control . . . . . . . . . . . . . . . . . . . . . . . . . .
access-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
authentication login . . . . . . . . . . . . . . . . . . . . .
auto-time-update . . . . . . . . . . . . . . . . . . . . . . . .
date-summer-time . . . . . . . . . . . . . . . . . . . . . . .
dial-peer
pots
fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
voip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
dmz-host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
dynamic-dns . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 2
4-25
4-25
4-21
4-21
4-21
4-22
4-23
4-24
4-23
4-24
4-24
4-26
4-26
4-27
4-28
4-28
4-29
4-29
4-30
4-30
4-31
4-31
4-32
4-32
4-33
4-33
4-33
4-34
4-34
4-35
4-35
4-36
4-36
4-36
4-37
4-37
4-37
4-38
4-38
4-38
4-39
4-39
4-39
host-filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-40
interface
multilink . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-42
serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-42
ip dhcp pool ethernet . . . . . . . . . . . . . . . . . . . . .4-43
ipsec
authentication-retries . . . . . . . . . . . . . . . . . . .4-40
log ike . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-40
log ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-41
replay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-41
vpn_ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-42
l2tpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-43
local-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-43
log sip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-44
mail-server authentication . . . . . . . . . . . . . . . . .4-44
nat-bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-44
network-object . . . . . . . . . . . . . . . . . . . . . . . . . .4-45
port-trigger-service . . . . . . . . . . . . . . . . . . . . . . .4-45
pptp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-45
pptps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-46
radius-client . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-46
remote-admin
icmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-46
snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-46
telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-47
udp-trace . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-47
web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-48
router ospf . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-48
security-log . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-49
service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-50
snmp-server . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-50
snmp-server traps . . . . . . . . . . . . . . . . . . . . . . . .4-50
static-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-51
time-range . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-51
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-51
vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-52
voice-codec . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-52
voice-port trunk . . . . . . . . . . . . . . . . . . . . . . . . .4-52
port-trigger service . . . . . . . . . . . . . . . . . . . . . . . . .4-53
pptpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-53
pptps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-53
radius-client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-54
remote-admin
icmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-54
snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-54
telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-55
udp-trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-55
web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-56
router ospf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-56
security-default . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-57
security-log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-58
service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-59
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Index
snmp-server
community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60
host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61
traps enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61
trusted-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61
static-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-62
time-range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-62
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-63
vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-63
vlan port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-64
voice-codec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-64
voice-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65
fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65
sip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-66
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-66
Configuration-DHCP Pool Ethernet
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
end-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
no
option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
static-lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
start-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
static-lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
subnet-mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
wins server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Configuration-Dial Peer FXS
block-out-caller-id . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
calling-party-disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
call-wait-caller-id . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
call-waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
codec preference . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
destination-pattern . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
fax-protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
modem-protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
no
block-out-caller-id . . . . . . . . . . . . . . . . . . . . . . . . 8-8
calling-party-disc . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
call-wait-caller-id . . . . . . . . . . . . . . . . . . . . . . . . 8-8
call-waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
codec preference . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
sip-authentication . . . . . . . . . . . . . . . . . . . . . . . . 8-9
sip-authentication
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
Configuration-Dial Peer Trunk
codec preference . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
destination-pattern . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
fax-protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
modem-protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
no
codec preference . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
destination-pattern . . . . . . . . . . . . . . . . . . . . . . . 9-6
sip-authentication . . . . . . . . . . . . . . . . . . . . . . . . 9-6
prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
sip-authentication
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
strip-digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Configuration-Dial Peer VoIP
destination-pattern . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4
no
destination-pattern . . . . . . . . . . . . . . . . . . . . . . 10-5
prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5
session-target . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5
prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
session-target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
strip-digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
user-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
Configuration-Ethernet Interface
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4
full-duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5
half-duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6
ip default-gateway . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
ip dhcp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8
Index - 3
Index
ip ospf
authentication . . . . . . . . . . . . . . . . . . . . . . . . . . 11-9
authentication-key . . . . . . . . . . . . . . . . . . . . . 11-10
cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-10
dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . 11-10
disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-11
hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . 11-11
message-digest-key . . . . . . . . . . . . . . . . . . . . . 11-11
priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
retransmit-interval . . . . . . . . . . . . . . . . . . . . . 11-12
transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13
ip proxy-arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13
ip rip
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14
receive-version . . . . . . . . . . . . . . . . . . . . . . . . 11-14
send-version . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-15
ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-15
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . 11-16
metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-16
no
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-17
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-17
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . 11-17
ip dhcp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-17
ip ospf
authentication . . . . . . . . . . . . . . . . . . . . . . . 11-18
authentication-key . . . . . . . . . . . . . . . . . . . 11-18
cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-18
dead-interval . . . . . . . . . . . . . . . . . . . . . . . . 11-18
disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-19
hello-interval . . . . . . . . . . . . . . . . . . . . . . . 11-19
message-digest-key . . . . . . . . . . . . . . . . . . 11-19
priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-20
retransmit-delay . . . . . . . . . . . . . . . . . . . . . 11-20
retransmit-interval . . . . . . . . . . . . . . . . . . . 11-20
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . 11-20
ip proxy-arp . . . . . . . . . . . . . . . . . . . . . . . . . . 11-21
ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-21
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-21
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . 11-21
remote-admin . . . . . . . . . . . . . . . . . . . . . . . . . 11-22
schedule-availability . . . . . . . . . . . . . . . . . . . . 11-22
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-22
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-22
tos ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-23
release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-23
remote-admin . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-23
renew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-23
schedule-availability . . . . . . . . . . . . . . . . . . . . . . 11-24
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-24
Index - 4
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-24
speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-25
tos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-25
Configuration-IPSec
aggressive-mode . . . . . . . . . . . . . . . . . . . . . . . . . . .14-2
authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-2
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-2
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-3
dpd-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-4
dpd-enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-4
dpd-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-4
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-5
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-5
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-5
group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-6
hash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-6
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-7
ip route metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-7
ipsec-conn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-8
ipsec-manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-8
key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-8
lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-9
local-subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-9
max-retries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-10
mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-10
netbios remote-brc-addr . . . . . . . . . . . . . . . . . . . .14-11
net-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-11
no
aggressive-mode . . . . . . . . . . . . . . . . . . . . . . . .14-12
dpd-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-12
dpd-enable . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-12
dpd-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . .14-12
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-13
group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-13
hash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-14
ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-14
ipsec
manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-14
netbios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-14
reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15
schedule-availability . . . . . . . . . . . . . . . . . . . .14-15
set-pfs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15
transform-set . . . . . . . . . . . . . . . . . . . . . . . . . .14-16
reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-17
rekey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-17
remote-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-17
remote-subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-18
schedule-availability . . . . . . . . . . . . . . . . . . . . . . .14-18
session-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-19
set-pfs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-19
transform-set . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-20
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Index
Configuration-L2TPC
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-2
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4
host-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5
ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5
ip ospf
authentication . . . . . . . . . . . . . . . . . . . . . . . . . . 15-6
authentication-key . . . . . . . . . . . . . . . . . . . . . . . 15-7
cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7
dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7
disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-8
hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-8
message-digest-key . . . . . . . . . . . . . . . . . . . . . . 15-8
priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-9
retransmit-interval . . . . . . . . . . . . . . . . . . . . . . . 15-9
transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . . 15-9
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-10
ip rip
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-10
receive-version . . . . . . . . . . . . . . . . . . . . . . . . 15-10
send-version . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-11
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-11
ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-12
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . 15-12
local-secret . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-12
metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-13
no
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-13
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-13
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . 15-14
ip ospf
authentication . . . . . . . . . . . . . . . . . . . . . . . 15-14
authentication-key . . . . . . . . . . . . . . . . . . . . 15-14
cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-14
dead-interval . . . . . . . . . . . . . . . . . . . . . . . . 15-15
disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-15
hello-interval . . . . . . . . . . . . . . . . . . . . . . . . 15-15
message-digest-key . . . . . . . . . . . . . . . . . . . 15-16
priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16
retransmit-interval . . . . . . . . . . . . . . . . . . . . 15-16
transmit-delay . . . . . . . . . . . . . . . . . . . . . . . 15-17
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . 15-17
ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . 15-18
ppp
authentication . . . . . . . . . . . . . . . . . . . . . . . 15-18
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . 15-18
exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . 15-18
on-demand . . . . . . . . . . . . . . . . . . . . . . . . . 15-19
password . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-19
restart-timer . . . . . . . . . . . . . . . . . . . . . . . . 15-19
time-btwn-reconnect . . . . . . . . . . . . . . . . . . 15-19
username . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-20
schedule-availability . . . . . . . . . . . . . . . . . . . . 15-20
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-20
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-20
ppp
authentication . . . . . . . . . . . . . . . . . . . . . . . . . 15-21
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-21
exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . 15-21
on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-22
password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-22
restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-22
time-btwn-reconnect . . . . . . . . . . . . . . . . . . . . 15-23
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-23
schedule-availability . . . . . . . . . . . . . . . . . . . . . . 15-23
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-24
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-24
Configuration-LCC Controller
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
no
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Configuration-Multilink Interface
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6
ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6
ip ospf
authentication . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7
authentication-key . . . . . . . . . . . . . . . . . . . . . . . 12-8
cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-8
dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-8
disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-9
hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-9
message-digest-key . . . . . . . . . . . . . . . . . . . . . . 12-9
priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-10
retransmit-interval . . . . . . . . . . . . . . . . . . . . . . 12-10
transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . 12-10
Index - 5
Index
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . .
ip rip enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ip rip receive-version . . . . . . . . . . . . . . . . . . . . .
ip rip send-version . . . . . . . . . . . . . . . . . . . . . . . .
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . .
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . .
metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
no
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ip default-router . . . . . . . . . . . . . . . . . . . . . . .
ip ospf
authentication . . . . . . . . . . . . . . . . . . . . . . .
authentication-key . . . . . . . . . . . . . . . . . . .
cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
dead-interval . . . . . . . . . . . . . . . . . . . . . . . .
disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
hello-interval . . . . . . . . . . . . . . . . . . . . . . .
message-digest-key . . . . . . . . . . . . . . . . . .
priority . . . . . . . . . . . . . . . . . . . . . . . . . . . .
retransmit-interval . . . . . . . . . . . . . . . . . . .
transmit-delay . . . . . . . . . . . . . . . . . . . . . . .
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . .
ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . .
ppp
authentication . . . . . . . . . . . . . . . . . . . . . . .
encryption . . . . . . . . . . . . . . . . . . . . . . . . . .
on-demand . . . . . . . . . . . . . . . . . . . . . . . . .
password . . . . . . . . . . . . . . . . . . . . . . . . . . .
qos interleaving . . . . . . . . . . . . . . . . . . . . .
username . . . . . . . . . . . . . . . . . . . . . . . . . . .
schedule-availability . . . . . . . . . . . . . . . . . . . .
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ppp
authentication . . . . . . . . . . . . . . . . . . . . . . . . .
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . .
exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . .
link-fragmentation . . . . . . . . . . . . . . . . . . . . .
on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . .
password . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
qos-interleaving . . . . . . . . . . . . . . . . . . . . . . .
restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . .
time-btwn-reconnect . . . . . . . . . . . . . . . . . . . .
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
schedule-availability . . . . . . . . . . . . . . . . . . . . . .
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 6
12-11
12-11
12-11
12-12
12-12
12-13
12-13
12-13
12-14
12-14
12-14
12-14
12-15
12-15
12-15
12-15
12-16
12-16
12-16
12-17
12-17
12-17
12-17
12-18
12-18
12-18
12-18
12-19
12-19
12-19
12-19
12-20
12-20
12-20
12-21
12-21
12-21
12-22
12-22
12-22
12-23
12-23
12-23
12-24
12-24
12-24
12-25
Configuration-OSPF
area authentication . . . . . . . . . . . . . . . . . . . . . . . . .16-2
area stub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-2
compatible rfc1583 . . . . . . . . . . . . . . . . . . . . . . . . .16-3
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-4
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-5
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-5
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-5
network area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-6
no
area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-7
area authentication . . . . . . . . . . . . . . . . . . . . . . .16-7
area stub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-7
compatible rfc1583 . . . . . . . . . . . . . . . . . . . . . . .16-8
network area . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-8
router-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-8
router-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-9
Configuration-PPTPC
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-2
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-3
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-3
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-3
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-4
host-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-4
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-5
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-5
ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-5
ip ospf
authentication . . . . . . . . . . . . . . . . . . . . . . . . . . .17-6
authentication-key . . . . . . . . . . . . . . . . . . . . . . .17-7
cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-7
dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-7
disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-8
hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . .17-8
message-digest-key . . . . . . . . . . . . . . . . . . . . . .17-8
priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-9
retransmit-interval . . . . . . . . . . . . . . . . . . . . . . .17-9
transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . . .17-9
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . .17-10
ip rip
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-10
receive-version . . . . . . . . . . . . . . . . . . . . . . . . .17-10
send-version . . . . . . . . . . . . . . . . . . . . . . . . . . .17-11
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-11
ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-12
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . .17-12
metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-12
no
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-13
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-13
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . .17-13
ip ospf
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Index
authentication . . . . . . . . . . . . . . . . . . . . . . . 17-13
authentication-key . . . . . . . . . . . . . . . . . . . . 17-14
cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-14
dead-interval . . . . . . . . . . . . . . . . . . . . . . . . 17-14
disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-14
hello-interval . . . . . . . . . . . . . . . . . . . . . . . . 17-15
message-digest-key . . . . . . . . . . . . . . . . . . . 17-15
priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-15
retransmit-interval . . . . . . . . . . . . . . . . . . . . 17-16
transmit-delay . . . . . . . . . . . . . . . . . . . . . . . 17-16
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . 17-16
ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-16
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-17
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . 17-17
ppp
authentication . . . . . . . . . . . . . . . . . . . . . . . 17-17
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . 17-17
exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . 17-18
on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18
password . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18
restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . 17-18
time-btwn-reconnect . . . . . . . . . . . . . . . . . . 17-19
username . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-19
schedule-availability . . . . . . . . . . . . . . . . . . . . 17-19
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-19
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-20
ppp
authentication . . . . . . . . . . . . . . . . . . . . . . . . . 17-20
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-20
idle-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-21
on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-21
password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-21
restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-22
time-btwn-reconnect . . . . . . . . . . . . . . . . . . . . 17-22
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-22
schedule-availability . . . . . . . . . . . . . . . . . . . . . . 17-23
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-23
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-23
Configuration-PPTPS
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-2
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-3
end-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-3
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-3
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-4
idle-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-4
no
idle-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-5
ppp
authentication . . . . . . . . . . . . . . . . . . . . . . . . 18-5
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-5
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
ppp
authentication . . . . . . . . . . . . . . . . . . . . . . . . . . 18-6
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-6
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-7
start-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-7
Configuration-RADIUS
authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-2
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-3
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-4
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-4
host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-5
key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-5
Configuration-Serial Interface
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3
encapsulation ppp . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6
ip mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6
ip ospf
authentication . . . . . . . . . . . . . . . . . . . . . . . . . . 13-7
authentication-key . . . . . . . . . . . . . . . . . . . . . . . 13-8
cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-8
dead-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-8
disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-9
hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-9
message-digest-key . . . . . . . . . . . . . . . . . . . . . . 13-9
priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-10
retransmit-interval . . . . . . . . . . . . . . . . . . . . . . 13-10
transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . 13-10
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-11
ip rip
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-11
receive-version . . . . . . . . . . . . . . . . . . . . . . . . 13-11
send-version . . . . . . . . . . . . . . . . . . . . . . . . . . 13-12
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-12
ip route-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-13
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . . . 13-13
metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-13
multilink-group . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14
no
encapsulation ppp . . . . . . . . . . . . . . . . . . . . . . 13-14
firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14
ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-15
ip default-route . . . . . . . . . . . . . . . . . . . . . . . . 13-15
ip ospf
authentication . . . . . . . . . . . . . . . . . . . . . . . 13-15
Index - 7
Index
authentication-key . . . . . . . . . . . . . . . . . . . 13-15
cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-16
dead-interval . . . . . . . . . . . . . . . . . . . . . . . . 13-16
disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-16
hello-interval . . . . . . . . . . . . . . . . . . . . . . . 13-16
message-digest-key . . . . . . . . . . . . . . . . . . 13-17
priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-17
retransmit-interval . . . . . . . . . . . . . . . . . . . 13-17
transmit-delay . . . . . . . . . . . . . . . . . . . . . . . 13-17
ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . 13-18
ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-18
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-18
ip secondary-dns . . . . . . . . . . . . . . . . . . . . . . . 13-18
ppp
authentication . . . . . . . . . . . . . . . . . . . . . . . 13-19
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . 13-19
on-demand . . . . . . . . . . . . . . . . . . . . . . . . . 13-19
password . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-19
username . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-20
schedule-availability . . . . . . . . . . . . . . . . . . . . 13-20
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-20
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-20
ppp
authentication . . . . . . . . . . . . . . . . . . . . . . . . . 13-21
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-21
exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . 13-21
link-fragmentation . . . . . . . . . . . . . . . . . . . . . 13-22
on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-22
password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-22
restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . . 13-23
time-btwn-reconnect . . . . . . . . . . . . . . . . . . . . 13-23
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-23
schedule-availability . . . . . . . . . . . . . . . . . . . . . . 13-24
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-24
sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-24
Configuration-T1 Controller
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
ds0-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
fdl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
framing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
idle-pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
lbo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
linecode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
loopdetect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
no
ds0-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
pri-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Index - 8
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-10
tdm-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-10
pri-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-10
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-11
tdm-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-11
threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-12
Configuration-VLAN
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-2
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-3
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-3
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-3
no
port-dot1q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-4
vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-4
port-dot1q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-5
port-priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-5
port-protocol-filter . . . . . . . . . . . . . . . . . . . . . . . . .20-6
pvid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-6
tag-all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-7
vlan-feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-7
Configuration-VLAN (port)
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-2
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-3
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-3
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-3
no
port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-4
voip-interface . . . . . . . . . . . . . . . . . . . . . . . . . . .21-4
port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-4
priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-5
voip-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-5
Configuration-Voice Port
digit-map (global) . . . . . . . . . . . . . . . . . . . . . . . . . .22-2
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-3
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-4
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-4
no
digit-map (global) . . . . . . . . . . . . . . . . . . . . . . . .22-5
signal
FXS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-8
tos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-5
Configuration-Voice Port FXS
comfort-noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-2
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-2
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-3
echo-cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-4
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-4
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-4
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-5
input-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-5
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Index
no
comfort-noise . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-6
echo-cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-6
per-line-logging . . . . . . . . . . . . . . . . . . . . . . . . . 23-6
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-6
output-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-7
per-line-logging . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-7
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-7
Configuration-Voice Port Trunk
comfort-noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-2
connection lcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-2
connection t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-2
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-3
digit-map (trunk) . . . . . . . . . . . . . . . . . . . . . . . . . . 24-3
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-4
echo-cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-5
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-5
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-5
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-6
input-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-6
isdn switch-type (PRI) . . . . . . . . . . . . . . . . . . . . . . 24-7
no
comfort-noise . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-8
connection lcc . . . . . . . . . . . . . . . . . . . . . . . . . . 24-8
connection t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-8
digit-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-9
echo-cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-9
registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-9
line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-10
line enable . . . . . . . . . . . . . . . . . . . . . . . . . . 24-10
line logging . . . . . . . . . . . . . . . . . . . . . . . . . 24-10
output-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-11
registration
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-12
line authentication . . . . . . . . . . . . . . . . . . . . . . 24-12
line enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-13
line first-phone-number . . . . . . . . . . . . . . . . . . 24-13
line logging . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-14
signal
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-14
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-15
Configuration-Voice Service SIP
calling-party-disc . . . . . . . . . . . . . . . . . . . . . . . . . . 25-2
conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-2
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-3
dtmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-4
early-media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-4
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-5
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-5
fax-protocol-t38
ecs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-6
redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-6
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-7
feature-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-7
gateway-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-8
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-8
no
conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-9
outbound-proxy . . . . . . . . . . . . . . . . . . . . . . . . . 25-9
prack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-9
proxy-server . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-9
redundancy
filter-incoming . . . . . . . . . . . . . . . . . . . . . . 25-10
rollback-timer . . . . . . . . . . . . . . . . . . . . . . . 25-10
registration
ignore-negotiated . . . . . . . . . . . . . . . . . . . . 25-10
session-timer mode . . . . . . . . . . . . . . . . . . . . . 25-10
outbound-proxy . . . . . . . . . . . . . . . . . . . . . . . . . . 25-11
phone-number . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-11
prack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-11
privacy-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-12
proxy-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-12
proxy-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-13
redundancy
advance-retries . . . . . . . . . . . . . . . . . . . . . . . . 25-13
advance-timeout . . . . . . . . . . . . . . . . . . . . . . . 25-14
filter-incoming . . . . . . . . . . . . . . . . . . . . . . . . 25-14
primary-address . . . . . . . . . . . . . . . . . . . . . . . 25-14
rollback-timer . . . . . . . . . . . . . . . . . . . . . . . . . 25-15
secondary-address . . . . . . . . . . . . . . . . . . . . . . 25-15
ttl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-16
type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-16
registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-17
rtp-base-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-17
session-timer
mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-18
refresher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-18
timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-19
sip-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-19
transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-19
configure terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
connection lcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-2
connection t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-2
copy
defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
running-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
D
date
auto-time-update . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
summer-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
timezone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Index - 9
Index
date (clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2, 3-4
debug . . . . . . . . 3-5, 3-6, 3-7, 3-8, 3-9, 3-10, 3-11, 3-12
delete local-server . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
description . 5-2, 6-2, 11-2, 12-2, 13-2, 14-2, 23-2, 24-3
destination-pattern . . . . . . . . . . . . . . . . . . . .8-3, 9-2, 10-2
dial-peer
pots
fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
voip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
digit-map (global) . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-2
digit-map (trunk) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-3
dmz-host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-13, .5-3, 6-3, 7-2, 8-4, 9-3, 10-3, 11-3, 12-3,
13-3, 14-3, 15-2, 16-4, 17-2, 18-2, 19-3, 20-2,
21-2, 22-3, 23-3, 24-4, 25-3
dpd-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4
dpd-enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4
dpd-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4
ds0-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
dtmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-4
dynamic-dns
backup-mx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
mail-exchanger . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
offline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
wildcard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
E
early-media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-4
echo-cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-4, 24-5
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
encapsulation ppp . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-5
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2, 3-12, 4-16, 5-4, 6-4, 7-3, 8-5, 9-4, 10-4, 11-4,
.12-4, 13-4, 14-5, 15-3, 16-5, 17-3, 18-3, 19-4,
20-3, 21-3, 22-4, 23-4, 24-5, 25-5
end-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3, 18-3
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3, 3-12, 4-16, 5-4, 6-4, 7-3, 8-5, 9-4, 10-4, 11-4,
.12-4, 13-4, 14-5, 15-3, 16-5, 17-3, 18-3, 19-4,
20-3, 21-3, 22-4, 23-4, 24-5, 25-5
F
fax-protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6, 9-4
fax-protocol-t38
ecs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-6
redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-6
signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-7
Index - 10
fdl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
feature-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-7
firewall . . . . . . . . . . . . . . . . 11-4, 12-4, 13-5, 15-3, 17-3
framing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
full-duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-5
G
gateway-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-8
group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-6
H
half-duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-5
hash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-6
help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3, 3-13, 4-17
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4, 3-14, 4-18, 5-5, 6-6, 7-4, 8-6, 9-5, 10-4, 11-6,
. 12-5, 13-5, 14-7, 15-4, 16-5, 17-4, 18-4, 19-4,
20-3, 21-3, 22-4, 23-5, 24-6, 25-8
host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-5
host-filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-19
host-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-4, 17-4
I
idle-pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-6
idle-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-4
input-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-5, 24-6
interface
ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-19
multilink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-20
serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-20
ip address . . . . . . . . . . . . . . 11-6, 12-5, 13-6, 15-5, 17-5
ip default-gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-7
ip default-route . . . . . . . . . . 11-7, 12-6, 13-6, 15-5, 17-5
ip dhcp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-7
ip dhcp pool ethernet . . . . . . . . . . . . . . . . . . . . . . . . . .4-25
ip domain-name . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-25
ip host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-25
ip mtu . . . . . . . . . . . . . . . . . 11-8, 12-6, 13-6, 15-5, 17-5
ip ospf
authentication . . . . . . . . . 11-9, 12-7, 13-7, 15-6, 17-6
authentication-key . . . . 11-10, 12-8, 13-8, 15-7, 17-7
cost . . . . . . . . . . . . . . . . 11-10, 12-8, 13-8, 15-7, 17-7
dead-interval . . . . . . . . . 11-10, 12-8, 13-8, 15-7, 17-7
disable . . . . . . . . . . . . . . 11-11, 12-9, 13-9, 15-8, 17-8
hello-interval . . . . . . . . . 11-11, 12-9, 13-9, 15-8, 17-8
message-digest-key . . . . 11-11, 12-9, 13-9, 15-8, 17-8
priority . . . . . . . . . . . 11-12, 12-10, 13-10, 15-9, 17-9
retransmit-interval . . 11-12, 12-10, 13-10, 15-9, 17-9
transmit-delay . . . . . . 11-12, 12-10, 13-10, 15-9, 17-9
ip primary-dns . . . . . . 11-13, 12-11, 13-11, 15-10, 17-10
ip proxy-arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-13
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Index
ip rip
enable . . . . . . . . . . . . . . . . 11-14, 13-11, 15-10, 17-10
receive-version . . . . . . . . . 11-14, 13-11, 15-10, 17-10
send-version . . . . . . . . . . . . . . . . . 11-14, 15-11, 17-11
ip rip enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-11
ip rip receive-version . . . . . . . . . . . . . . . . . . . . . . . . 12-11
ip rip send-version . . . . . . . . . . . . . . . . . . . . . . . . . . 12-12
ip rip"send-version . . . . . . . . . . . . . . . . . . . . . . . . . . 13-12
ip route . . . . . . . . . . . 11-15, 12-12, 13-12, 15-11, 17-11
ip route metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-7
ip route-mode . . . . . . 11-15, 12-13, 13-13, 15-12, 17-12
ip secondary-dns . . . 11-16, 12-13, 13-13, 15-12, 17-12
ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
authentication-retries . . . . . . . . . . . . . . . . . . . . . . . 4-21
key generate key . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
log ike . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
log ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
net-to-host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
net-to-net . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
replay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
vpn_ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
ipsec-conn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-8
ipsec-manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-8
isdn switch-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-7
K
key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26, 14-8, 19-5
L
l2tpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
lbo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-9
linecode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
load configuration file . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
local-secret . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-12
local-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27
local-subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-9
log
lcc
buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
notify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
pri . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29
security
buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29
notify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30
sip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30
system
buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31
notify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31
t1
buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
notify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32
log clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
loopdetect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
M
mail-server
authentication enable . . . . . . . . . . . . . . . . . . . . . . . 4-33
from-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33
host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33
port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34
max-retries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-10
metric . . . . . . . . . . . . . 11-16, 12-13, 13-13, 15-13, 17-12
mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-10
modem-protocol . . . . . . . . . . . . . . . . . . . . . . . . . 8-7, 9-5
multilink-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14
N
nat-bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35
netbios remote-brc-addr . . . . . . . . . . . . . . . . . . . . . 14-11
net-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-11
network area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-6
network-object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35
no
access lan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36
access wan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36
access-control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36
access-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37
aggressive-mode . . . . . . . . . . . . . . . . . . . . . . . . . 14-12
area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-7
area authentication . . . . . . . . . . . . . . . . . . . . . . . . 16-7
area stub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-7
authentication login . . . . . . . . . . . . . . . . . . . . . . . . 4-37
auto-time-update . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37
block-out-caller-id . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
calling-party-disc . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
call-wait-caller-id . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
call-waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
codec preference . . . . . . . . . . . . . . . . . . . . . . . 8-9, 9-6
comfort-noise . . . . . . . . . . . . . . . . . . . . . . . 23-6, 24-8
compatible rfc1583 . . . . . . . . . . . . . . . . . . . . . . . . 16-8
conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-9
connection lcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-8
connection t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-8
date-summer-time . . . . . . . . . . . . . . . . . . . . . . . . . 4-38
debug
portmon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
destination-pattern . . . . . . . . . . . . . . . . . . . . . 9-6, 10-5
dial-peer
pots
Index - 11
Index
fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38
voip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39
digit-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-9
digit-map (global) . . . . . . . . . . . . . . . . . . . . . . . . . 22-5
dmz-host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39
dpd-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-12
dpd-enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-12
dpd-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-12
ds0-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
dynamic-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39
echo-cancel . . . . . . . . . . . . . . . . . . . . . . . . . 23-6, 24-9
encapsulation ppp . . . . . . . . . . . . . . . . . . . . . . . . 13-14
encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-13
firewall . . . . . . . . . 11-17, 12-14, 13-14, 15-13, 17-13
group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-13
hash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-14
host-filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-40
idle-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-5
interface
multilink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42
serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42
ip address . . . . . . . 11-17, 12-14, 13-15, 15-13, 17-13
ip default-route . . . . . . . . .11-17, 13-15, 15-14, 17-13
ip default-router . . . . . . . . . . . . . . . . . . . . . . . . . 12-14
ip dhcp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-17
ip dhcp pool ethernet . . . . . . . . . . . . . . . . . . . . . . . 4-43
ip ospf
authentication . . 11-18, 12-14, 13-15, 15-14, 17-13
authentication-key 11-18, 12-15, 13-15, 15-14, 17-14
cost . . . . . . . . . . 11-18, 12-15, 13-16, 15-14, 17-14
dead-interval . . . 11-18, 12-15, 13-16, 15-15, 17-14
disable . . . . . . . . 11-19, 12-15, 13-16, 15-15, 17-14
hello-interval . . . 11-19, 12-16, 13-16, 15-15, 17-15
message-digest-key 11-19, 12-16, 13-17, 15-16, 17-15
priority . . . . . . . 11-20, 12-16, 13-17, 15-16, 17-15
retransmit-interval 11-20, 12-17, 13-17, 15-16, 17-16
transmit-delay . . 11-20, 12-17, 13-17, 15-17, 17-16
ip primary-dns . . . . 11-20, 12-17, 13-18, 15-17, 17-16
ip proxy-arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-21
ip rip . . . . . 11-21, 12-17, 13-18, 14-14, 15-17, 17-16
ip route . . . . . . . . . 11-21, 12-18, 13-18, 15-17, 17-17
ip secondary-dns . . 11-21, 12-18, 13-18, 15-18, 17-17
ipsec
authentication-retries . . . . . . . . . . . . . . . . . . . . 4-40
log ike . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-40
log ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41
manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-14
replay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41
vpn_ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42
l2tpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-43
local-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-43
Index - 12
log sip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-44
mail-server authentication . . . . . . . . . . . . . . . . . . .4-44
nat-bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-44
netbios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-14
network area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-8
network-object . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-45
option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-5
outbound-proxy . . . . . . . . . . . . . . . . . . . . . . . . . . .25-9
per-line-logging . . . . . . . . . . . . . . . . . . . . . . . . . . .23-6
port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-4
port-dot1q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-4
port-trigger-service . . . . . . . . . . . . . . . . . . . . . . . . .4-45
ppp
authentication . . . 12-18, 13-19, 15-18, 17-17, 18-5
encryption . . . . . . 12-18, 13-19, 15-18, 17-17, 18-5
exec-timeout . . . . . . . . . . . . . . . . . . . . .15-18, 17-18
on-demand . . . . . . . . . . 12-19, 13-19, 15-19, 17-18
password . . . . . . . . . . . . 12-19, 13-19, 15-19, 17-18
qos-interleaving . . . . . . . . . . . . . . . . . . . . . . . .12-19
restart-timer . . . . . . . . . . . . . . . . . . . . .15-19, 17-18
time-btwn-reconnect . . . . . . . . . . . . . .15-19, 17-19
username . . . . . . . . . . . 12-19, 13-20, 15-20, 17-19
pptp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-45
pptps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-46
prack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-9
prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-5
pri-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-9
proxy-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-9
radius-client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-46
reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15
redundancy
filter-incoming . . . . . . . . . . . . . . . . . . . . . . . . .25-10
rollback-timer . . . . . . . . . . . . . . . . . . . . . . . . . .25-10
registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-9
ignore-negotiated . . . . . . . . . . . . . . . . . . . . . . .25-10
line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-10
line enable . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-10
line logging . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-10
relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-5
remote-admin . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-22
icmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-46
snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-46
telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-47
udp-trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-47
web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-48
router ospf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-48
router-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-8
schedule-availability 11-22, 12-20, 13-20, 14-15, 15-20,
17-19
security-log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-49
service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-50
session-target . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-5
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Index
session-timer mode . . . . . . . . . . . . . . . . . . . . . . . 25-10
set-pfs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15
shutdown . . . . 5-5, 6-10, 11-22, 12-20, 13-20, 15-20,
17-19, 18-6, 23-6
sip-alg . . . . . . . . . 11-22, 12-20, 13-20, 15-20, 17-20
sip-authentication . . . . . . . . . . . . . . . . . . . . . . . 8-9, 9-6
snmp-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-50
snmp-server traps . . . . . . . . . . . . . . . . . . . . . . . . . . 4-50
static-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-51
static-lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
tdm-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
time-range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-51
tos ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-23
transform-set . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-16
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-51
vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-52, 20-4
voice-codec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-52
voice-port trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-52
voip-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-4
O
option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
outbound-proxy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-11
output-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-7, 24-11
P
per-line-logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-7
phone-number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-11
ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5, 3-17
port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-4
port-dot1q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-5
portmon
{rx|tx|both} . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
multilink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
raw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
port-priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-5
port-protocol-filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-6
port-trigger service . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53
ppp
authentication . . . . . 12-21, 13-21, 15-21, 17-20, 18-6
encryption . . . . . . . 12-21, 13-21, 15-21, 17-20, 18-6
exec-timeout . . . . . . . . . . . . . . . . 12-21, 13-21, 15-21
idle-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-21
link-fragmentation . . . . . . . . . . . . . . . . . . 12-22, 13-22
on-demand . . . . . . . . . . . . 12-22, 13-22, 15-22, 17-21
password . . . . . . . . . . . . . 12-22, 13-22, 15-22, 17-21
qos-interleaving . . . . . . . . . . . . . . . . . . . . . . . . . . 12-23
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
restart-timer . . . . . . . . . . . .12-23, 13-23, 15-22, 17-22
time-btwn-reconnect . . . . .12-23, 13-23, 15-23, 17-22
username . . . . . . . . . . . . . .12-24, 13-23, 15-23, 17-22
pptpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53
pptps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53
prack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-11
prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7, 10-6
pri-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-5
privacy-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-12
Priviledged Mode
show
controller lcc . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35
Privileged Mode
clear
arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
caclkcd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
ip ospf process . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
configure terminal . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
copy
defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
running-config . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
date (clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
debug
portmon
{rx|tx|both} . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
management . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
multilink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
raw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
log clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
no
debug
portmon . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
reload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
caclkcd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
config
access-control . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Index - 13
Index
access-list . . . . . . . . . . . . . . . . . . . . . . . . . . .
controller t1 . . . . . . . . . . . . . . . . . . . . . . . . .
dmz-host . . . . . . . . . . . . . . . . . . . . . . . . . . . .
host-filter . . . . . . . . . . . . . . . . . . . . . . . . . . .
interface
ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . .
multilink . . . . . . . . . . . . . . . . . . . . . . . . . .
serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ip dhcp ethernet . . . . . . . . . . . . . . . . . . . . . .
local-server . . . . . . . . . . . . . . . . . . . . . . . . . .
nat-bypass . . . . . . . . . . . . . . . . . . . . . . . . . . .
network-object . . . . . . . . . . . . . . . . . . . . . . .
port-trigger . . . . . . . . . . . . . . . . . . . . . . . . . .
remote-admin . . . . . . . . . . . . . . . . . . . . . . . .
security-default . . . . . . . . . . . . . . . . . . . . . . .
security-log . . . . . . . . . . . . . . . . . . . . . . . . . .
service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
static-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . .
time-range . . . . . . . . . . . . . . . . . . . . . . . . . . .
voice-port
fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
controller t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
digit-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
interface
description . . . . . . . . . . . . . . . . . . . . . . . . . .
ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
multilink . . . . . . . . . . . . . . . . . . . . . . . . . . . .
serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ip ospf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
database . . . . . . . . . . . . . . . . . . . . . . . . . . . .
interface . . . . . . . . . . . . . . . . . . . . . . . . . . . .
neighbor . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mac-address-table . . . . . . . . . . . . . . . . . . . . . . .
nat-fw (NAT-Firewall) . . . . . . . . . . . . . . . . . . .
port-trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . .
pptpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
pptps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
running-config . . . . . . . . . . . . . . . . . . . . . . . . .
service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
voice-port
fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
tracerpite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Proviledged Mode
show
Index - 14
3-23
3-24
3-25
3-25
dhcp-leases . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-37
proxy-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-12
proxy-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-13
pvid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-6
3-26
3-27
3-28
3-29
3-29
3-30
3-30
3-30
3-31
3-31
3-31
3-32
3-32
3-32
R
3-33
3-34
3-36
3-37
3-38
3-39
3-39
3-40
3-41
3-42
3-44
3-45
3-46
3-49
3-50
3-50
3-51
3-52
3-53
3-53
3-54
3-61
3-62
3-62
3-64
3-65
3-67
3-67
radius-client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-54
reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-17
redundancy
advance-retries . . . . . . . . . . . . . . . . . . . . . . . . . . .25-13
advance-timeout . . . . . . . . . . . . . . . . . . . . . . . . . .25-14
filter-incoming . . . . . . . . . . . . . . . . . . . . . . . . . . .25-14
primary-address . . . . . . . . . . . . . . . . . . . . . . . . . .25-14
rollback-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-15
secondary-address . . . . . . . . . . . . . . . . . . . . . . . . .25-15
ttl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-16
type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-16
registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-17
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-12
line authentication . . . . . . . . . . . . . . . . . . . . . . . .24-12
line enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-13
line first-phone-number . . . . . . . . . . . . . . . . . . . .24-13
line logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-14
rekey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-17
relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-6
release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-23
reload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18
remote-admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-23
icmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-54
snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-54
telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-55
udp-trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-55
web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-56
remote-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-17
remote-subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-18
renew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-23
restore defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
router ospf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-56
router-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-9
rtp-base-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-17
S
save configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
schedule-availability 11-24, 12-24, 13-24, 14-18, 15-23,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-23
security log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-58
security-default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-57
service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-59
session-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-19
session-target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-6
session-timer
mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-18
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Index
refresher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-18
timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-19
set-pfs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-19
show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6, 3-19
alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7, 3-20
arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8, 3-21
caclkcd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9, 3-22
config
access-control . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
access-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
controller t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
dmz-host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
host-filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
interface
ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
multilink . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
ip dhcp ethernet . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
local-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
nat-bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
network-object . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
port-trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
remote-admin . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31
voice-port
fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-34
config dynamic-dns . . . . . . . . . . . . . . . . . . . . . . . . 2-10
controller lcc . . . . . . . . . . . . . . . . . . . . . . . . 2-10, 3-35
controller t1 . . . . . . . . . . . . . . . . . . . . . . . . . 2-11, 3-36
dhcp-leases . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12, 3-37
digit-map . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12, 3-37
interface
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-38
ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39
multilink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39
serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40
interface description . . . . . . . . . . . . . . . . . . . . . . . . 2-13
interface ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
interface multilink . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
interface serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
interface stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
ip ospf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18, 3-41
database . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19, 3-42
interface . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21, 3-44
neighbor . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22, 3-45
ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-46
licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23, 3-49
mac-address-table . . . . . . . . . . . . . . . . . . . . 2-24, 3-50
nat-fw (NAT-firewall) . . . . . . . . . . . . . . . . . 2-25, 3-50
port-trigger . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26, 3-51
pptpc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-52
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
pptps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-53
route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26, 3-53
running-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54
security-default . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31
security-log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31
service . . . . . . . . . . . . . . . . . . . . . . . . .2-27, 3-32, 3-61
static-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
time-range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28, 3-62
version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28, 3-62
voice-port
fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-64
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-65
voice-port fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
voice-port trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6, 6-11, 11-24, 12-24, 13-24, 15-24, 17-23,
18-7, 23-7
signal
FXS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-8
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-14
sip-alg . . . . . . . . . . . . 11-24, 12-25, 13-24, 15-24, 17-23
sip-authentication
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10, 9-7
password . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10, 9-7
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10, 9-8
sip-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-19
snmp-server
community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60
host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61
traps enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61
snmp-trusted-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61
speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-25
start-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7, 18-7
static-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-62
static-lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
strip-digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8, 10-7
subnet-mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
T
tag-all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-7
tdm-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
time-range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-62
tos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-25, 22-5
trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33, 3-67
transform-set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-20
transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-19
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-15
Index - 15
Index
U
upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-67
User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
date (clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
caclkcd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
config dynsmic-dns . . . . . . . . . . . . . . . . . . . . . . 2-10
controller lcc . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
controller t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
dhcp-leases . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
digit-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
interface description . . . . . . . . . . . . . . . . . . . . . 2-13
interface ethernet . . . . . . . . . . . . . . . . . . . . . . . 2-14
interface multilink . . . . . . . . . . . . . . . . . . . . . . . 2-14
interface serial . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
interface stats . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
ip ospf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
database . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
neighbor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
mac-address-table . . . . . . . . . . . . . . . . . . . . . . . 2-24
nat-fw (NAT-Firewall) . . . . . . . . . . . . . . . . . . . 2-25
port-trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
voice-port fxs . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
voice-port trunk . . . . . . . . . . . . . . . . . . . . . . . . 2-31
traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33
tracerpite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33
user-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-63
Index - 16
V
vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-63, 4-64
vlan-feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-7
voice-codec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-64
voice-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-65
fxs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-65
sip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-66
trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-66
voip-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-5
W
wins server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-8
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI
Download PDF

advertising