Casio 1507 Watch User Manual

Module No. 1506/1507
1506/1507-1
GETTING ACQUAINTED
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchases, be sure to carefully read this manual and keep it on hand for later reference
when necessary.
About this manual
• Button operations are indicated using the
letters shown in the illustration.
A
(ADJUST)
P
DST
24
VIB
P
MODE
REV
L
FWD
(LIGHT)
R M F
(REV)
(FWD)
(MODE)
GENERAL GUIDE
• Press M (MODE) to change from mode to mode. After you perform an operation in any mode, pressing M returns to the Timekeeping Mode.
• In addition to the modes shown below, this watch also features a VIVCEL function that performs cell phone paging operations.
• The animation area shows different animated figures and graphics, depending on the mode and the operation being performed.
World Time Mode
Timekeeping Mode
Alarm Mode
Countdown Alarm Mode
Animation area
Press M.
P
P
P
DST
24
VIB
P
DST
24
VIB
P
DST
▲
▲
▲
A
24
P
VIB
P
DST
VIB
Stopwatch Mode
L
FWD
MODE
▲
REV
R M F
P
DST
24
P
TIMEKEEPING MODE
This section provides information on setting the time and using the backlight.
• Pressing A (ADJUST) in the Timekeeping Mode toggles the animation area
between the day of the week and graphics that show when the paging operation is
activated.
Day of the week
Paging Interval
Day of the week
Animation area
Month – Day
A
Press A.
P
▲
VIB
P
▲
DST
24
P
DST
24
P
REV
PM indicator
MODE
VIB
L
FWD
R M F
Seconds
• See “VIVCEL” for details on the paging interval.
• Timekeeping Mode time is linked with World Time Mode time, so be sure to select the
city code for your current location before setting the time in the Timekeeping Mode.
6. Press M until the hour digits are flashing on the display.
7. Press F to increase the setting or R to decrease it. Holding down either button
changes the setting at high speed.
8. Repeat steps 6 and 7 to set the minutes, year, month, and day.
• The time system is selected (flashing), press F to switch between the 12-hour
(12H) and 24-hour (24H) formats.
• When the 12-hour format is selected, the 12H indicator appears on the display.
With the 12-hour format, the P (PM) indicator appears on the display to indicate
“p.m.” times. There is no indicator for “a.m.” times.
• Selecting the 24-hour format causes the 24H and the 24 indicators to appear on
the display.
9. After you make the settings you want, press A to return to the Timekeeping Mode.
• The day of the week is automatically set in accordance with the date.
• The date can be set within the range of January 1, 1995 to December 31, 2039.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
Daylight saving time (DST), which is also sometimes called “summer time,” advances
the time for one hour, as is the custom in some areas during the summer. Remember
that not all countries or even local areas use Daylight Saving Time.
DST on indicator
DST indicator
To set the city code, time, and date
Time system indicator 1. Hold down A while in the Timekeeping Mode until
A
P
DST
24
VIB
P
REV
MODE
FWD
L
R M F
the seconds digits start to flash on the display. The
seconds flash because they are selected.
• In this Timekeeping Mode setting screen, the
animation area shows the year and time system
indicator.
2. While the seconds digits are selected (flashing),
press F (FWD) to reset the seconds to 00.
• If you press F while the seconds count is in the range
of 30 to 59, the seconds are reset to 00 and 1 is
added to the minutes. If the seconds count is in the
range of 00 to 29, the minutes count is unchanged.
3. Press M to change the selection in the following sequence.
Seconds
City Code
Month
Day
Year
DST on/off
Time system
Hour
Minutes
• See “To switch between standard time and daylight saving time” for details on DST
On/Off setting.
City code
P
DST
24
P
VIB
GMT differential
VIB
To switch between standard time and daylight saving time
Hour : Minutes
Year
▲
24
P
4. Press M until the city code is flashing on the display.
5. Use F and R (REV) to scroll through the city
codes until you find the one you want to set as your
home city.
• F scrolls forward, while R scrolls back through
the city codes. Holding down either button scrolls
through the city codes at high speed.
• See the “CITY CODE TABLE” at the back of this
manual for a complete list of available codes.
• The GMT differential is difference between the time in the displayed time and
Greenwich Mean Time (GMT). The GMT differentials used by this watch are based
on Universal Time Coordinated (UTC) data.
A
P
DST
DST
24
VIB
P
REV
MODE
FWD
L
R M F
1. Hold down A while in the Timekeeping Mode until
the seconds digits start to flash on the display. The
seconds flash because they are selected.
2. Press M twice to move the flashing to the DST on/
off setting.
3. Press F to toggle daylight saving time on (ON)
and off (OF).
4. After you make the setting you want, press A to
return to the Timekeeping Mode.
• The DST indicator appears on the display to indicate
that daylight saving time is turned on.
About the backlight
The backlight uses an EL (electro-luminescent) panel that causes the entire display
to glow for easy reading in the dark. Pressing L (LIGHT) in any mode turns on the
EL backlight for about three seconds.
• The backlight remains lit for about three seconds from the point you press L,
even if it is already lit when you press L. If you keep depressed for three seconds,
the backlight will automatically turn off.
• Pressing L lights the backlight and causes a 10-second animation to play.
• The electro-luminescent panel loses illuminating power after very long use.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch will emit an audible sound whenever the display is illuminated. This is
caused by a transformer that vibrates when the EL panel lights up. It does not
indicate malfunction of the watch.
• The backlight automatically turns off whenever an alarm sounds or a paging
operation is performed.
1506/1507-2
To turn VIVCEL on and off
VIVCEL
The VIVCEL function performs a vibration paging operation when your cell phone
receives a call. The vibration paging operation lasts for up to 10 seconds, or until you
press any watch button.
Animation area
A
P
DST
24
VIB
P
VIVCEL Settings
The following explains the settings you need to make to use the VIVCEL functions.
See “To make VIVCEL settings” for details on actually making the settings.
REV
MODE
L
FWD
R M F
Cell Phone System
VIVCEL can be used with cell phones only. It cannot be used with other (non-cell)
telephones.
Cell phone system compatibility depends on your watch’s “module” number, which
can be found on its back cover. The following shows telephone system compatibility
for each module.
Module 1506 (AMPS compatible)
Module 1507 (GSM compatible)
In the Timekeeping Mode, hold down F for about
one second to toggle VIVCEL on ( displayed in the
animation area) and off ( displayed).
• When VIVCEL is turned off, the animation area
shows a sleeping figure ( ).
• While VIVCEL is turned on, it becomes activated
when the current time is within the paging interval
defined by the VIVCEL start and end times. The
animation area of the display shows a moving
antenna figure ( ) and is displayed while VIVCEL
is activated. Outside the paging interval defined by
the VIVCEL start and end times, VIVCEL is
deactivated and the animation area of the display
shows a non-moving antenna figure ( ).
VIVCEL Operation
Note that for VIVCEL to operate correctly, it must be
turned on (by holding down F) and activated (the
current time is within the paging interval defined by
A the VIVCEL start and end times).
• Pressing A in the Timekeeping Mode toggles the
animation area between the day of the week and
the paging interval.
L • The paging interval is indicated by a bar graph in
FWD
MODE
REV
the animation area. The nearby illustration indicates
R M F
a paging interval of 10 am to 11 pm.
6
12
•
VIVCEL automatically activates and deactivates
AM
during the defined paging interval.
Paging Interval
Watch Setting
Telephone System
Digital cell phone
DIGTL
Analog cell phone
ANLOG
Digital/analog cell
phone switching
DUAL
Telephone System
Watch Setting
GSM network cell
phone
DIGTL
Non-GSM network
cell phone
ANLOG
P
DST
24
• See the documentation that comes with your cell phone for information about which
type it is.
• Module 1507 may not be compatible with certain non-GSM network phone systems.
P
0
VIB
PM
Paging Interval
Presetting a start time and end time defines the “paging interval”. VIVCEL is activated
each day during the paging interval and deactivated outside the paging interval (as
long as VIVCEL is turned on). You can specify the hour only for these times, within
the range of 1 (1 o’clock) to 24 (midnight).
Sensitivity
The VIVCEL paging function operates by picking up signals from your cell phone.
The sensitivity setting determines how close a cell phone has to be from the watch for
it to pick up these signals.
Watch Setting
HIGH
LOW
Approximate Distance
When to use
1 meter (40 inches)
When your phone is in a pocket that is
away from the watch.
50 centimeters (20 inches)
When your phone is located near the
watch.
When there are other cell phone users
nearby.
To make VIVCEL settings
P
DST
24
VIB
P
REV
MODE
FWD
R M F
P
DST
24
VIB
P
Start time
P
DST
24
VIB
P
P
DST
24
P
VIB
1. Hold down A while in the Timekeeping Mode until
the seconds digits start to flash on the display.
2. Press L to display the cell phone system setting
screen.
A
• At this time the current cell phone system indicator
(DIGTL, ANLOG, or DUAL) flashes on the
display.
L 3. Press R or F to scroll through the available cell
phone system indicators until the one you want is
displayed.
4. Press M to advance to the start time setting screen.
• At this time the current start time setting flashes on
the display.
5. Press F to increase the time or R to decrease it.
Holding down either button changes the start time
setting at high speed.
6. Press M to advance to the end time setting screen.
• At this time the current end time setting flashes on
the display.
7. Press F to increase the time or R to decrease it.
Holding down either button changes the end time
setting at high speed.
8. Press M to advance to the sensitivity setting
screen.
• At this time the current sensitivity setting flashes on
the display.
9. Press R or F to toggle between the sensitivity
settings.
10. After you make the settings you want, press A to return to the Timekeeping
Mode.
• Pressing M instead of A returns to the screen in step 2.
• If you do not operate any button for a few minutes while a selection is flashing, the
watch goes back to the Timekeeping Mode automatically.
Current time (flashing)
Manual VIVCEL Activation
Press R in the Timekeeping Mode to add two to the current paging interval hour and
round the minutes digits to zero. This means that if it is 10:58 p.m. when you press
R, the paging interval is extended up to 00:00 a.m. Each press of R adds two
hours, up to a total of eight hours.
• Pressing R while VIVCEL is deactivated (outside the paging period), activates
VIVCEL. The watch vibrates when VIVCEL is activated.
• The R button can be used to extend the paging interval for up to eight hours (four
R button operations).
• Any extension of the paging interval with the R button is automatically cancelled
whenever you turn off VIVCEL or change any of its settings.
VIVCEL Precautions
• Since VIVCEL operates by picking up signals from your cell phone, a paging
operation may also be triggered by an outgoing call or even while a call is in progress.
A paging operation can also be triggered by another cell phone or other device
operating on the same frequency as your cell phone.
• Any of the following conditions can cause interference with VIVCEL paging operations.
Obstruction between the watch and cell phone
Sensitivity set to LOW while the watch is located away from the cell phone
Use with a non-compatible telephone system
• Frequent use of VIVCEL paging can shorten battery life.
• Turn off VIVCEL before operating a motor vehicle or bicycle to avoid the
chance of accident caused by a paging operation while operating a vehicle.
WORLD TIME MODE
The World Time Mode shows the current time in 27
cities (29 time zones) around the world.
City code
Timekeeping in the World Time Mode
A The current time in all the World Time zones is
calculated in accordance with the Greenwich Mean
P
Time (GMT) differential for each zone, based on the
current home time setting in the Timekeeping Mode.
L
FWD
MODE
REV
You can also turn Daylight Saving Time (DST) on or
off separately for each time zone. Turning on daylight
R M F
saving time automatically advances the corresponding
Current time
time setting by one hour.
Current time in
• The seconds count of the World Time is synchronized
the selected city
with the seconds count in the Timekeeping Mode.
P
DST
24
VIB
• The 12-hour/24-hour format of the World Time matches the format you select in the
Timekeeping Mode.
• With daylight saving time, clocks are set one hour forward in order to better take
advantage of daylight hours during the summer, when days are longer. Whether or
not daylight saving time is used depends on the country you are in.
To view the Time in Another Zone
Press F while in the World Time Mode to scroll forward through the city codes (time
zones) and R to scroll back.
• Holding down either button scrolls through the city codes at high speed.
• For full information on city codes, see the “CITY CODE TABLE” at the back of this
manual.
• The time zone that is displayed when you leave the World Time Mode will still be
displayed when you enter the World Time Mode again.
1506/1507-3
To switch a Zone between Standard Time and Daylight
Saving Time
1. In the World Time Mode, display the time zone (city
code) whose standard time/daylight saving time
setting you want to change.
• You can make separate settings for each zone (city).
2. Hold down A for about two seconds to toggle
daylight saving time on (DST displayed) and off
(DST not displayed).
• The DST indicator appears whenever daylight saving
time is turned on for the zone (city) whose time is
currently on the display.
DST indicator
A
DSTP
DST
24
VIB
P
REV
MODE
L
FWD
R M F
ALARM MODE
When the Daily Alarm is turned on, an alarm operation
(tone or vibration) is performed for 20 seconds at the
preset time each day. Press any button to stop the
alarm operation after it starts. A time signal operation
(tone or vibration) is performed every hour on the hour
while the Hourly Time Signal is turned on.
• You can select either tone or vibration for the alarm
and hourly time signal operations.
• Alarm and hourly time signal operations are
performed in accordance with the time kept in the
Timekeeping Mode.
Current time
A
P
DST
24
VIB
P
REV
MODE
L
FWD
R M F
3. Press F to increase the setting or R to decrease it. Holding down either button
changes the setting at high speed.
• To set the starting value of the countdown time to 24 hours, set 0:00.
4. After you set the countdown time, press A to return to the Countdown Alarm
Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Countdown Alarm Mode.
To use the countdown timer
Press F while in the Countdown Alarm Mode to start the countdown timer.
• When the countdown reaches zero, the Countdown Alarm operation is performed
for about 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the Countdown Alarm operation
stops.
• Press F while a countdown operation is in progress to pause it. Press F again to
resume the countdown.
• To complete stop a countdown operation, first pause it (by pressing F), and then
press R. This returns the countdown time to its starting value.
STOPWATCH MODE
1/100 of second
A
P
DST
24
VIB
P
Alarm on indicator
Hour : Minutes
Hourly time signal
on indicator
REV
MODE
FWD
L
R M F
Minutes
Hours
To set the alarm time
Seconds
1. Hold down A while in the Alarm Mode until the hour digits start to flash on the
display. The hour digits flash because they are selected.
• This operation automatically turns on the Daily Alarm.
2. Press M to change the selection in the following sequence.
Hour
The Stopwatch Mode lets you measure elapsed time,
split times, and 1st-2nd place times. The range of the
stopwatch is 23 hours, 59 minutes, 59.99 seconds.
(a) Elapsed time measurement
JF
JF
F
Start
Stop
Re-start
To turn the Daily Alarm and Hourly Time Signal on and off
Press F while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
Both OFF
Daily Alarm Only
Hourly Time
Signal Only
To switch between Tone and Vibration
A
P
DST
VIB
VIB
24
P
REV
MODE
Each press of R in the Alarm Mode toggles between
vibration ( VIB displayed) and tone ( VIB not displayed)
for the alarm and hourly time signal operations.
• The selection you make here is also applied for the
Countdown Alarm.
L
FWD
To test the alarm operation
R M F
In the Alarm Mode, hold down F to perform the
currently selected alarm operation.
COUNTDOWN ALARM MODE
1/10 second
A
P
DST
24
VIB
P
REV
MODE
FWD
R M F
Minutes
Seconds
Hours
L
The countdown timer can be set within a range of 1
minute to 24 hours. When the countdown reaches zero,
a countdown alarm operation (vibration or tone) is
performed for about 10 seconds.
• Use the procedure under “To switch between Tone
and Vibration” to select vibration or tone for the
Countdown Alarm.
To set the countdown time
1. Hold down A while in the Countdown Alarm Mode
until the hours digit starts to flash on the display.
The hours digit flashes because it is selected.
2. Press M to change the selection in the following
sequence.
Hours
Minutes
J
R
Clear
J
R
Clear
(c) Split time and 1st-2nd place times
JR
JF
JR
JR
F
Start
Split
Stop
Split release Clear
First
runner
finishes.
Second runner Record time of
finishes.
second runner.
Record time of
first runner.
CITY CODE TABLE
GMT
Differential
–11
HONOLULU
–10
ANCHORAGE
–09
LOS ANGELES
–08
City
Other major cities in same time zone
DEN
CHI
DENVER
CHICAGO
–07
–06
NYC
NEW YORK
–05
CCS
RIO
–––
–––
GMT
LON
PAR
CARACAS
RIO DE JANEIRO
–04
–03
–02
–01
+00
PAGO PAGO
PAPEETE
NOME
SAN FRANCISCO, LAS VEGAS,
VANCOUVER, SEATTLE, DAWSON CITY
EL PASO, EDMONTON
HOUSTON, DALLAS/FORT WORTH, NEW
ORLEANS, MEXICO CITY, WINNIPEG
MONTREAL, DETROIT, MIAMI, BOSTON,
PANAMA CITY, HAVANA, LIMA, BOGOTA
LA PAZ, SANTIAGO, PORT OF SPAIN
SAO PAULO, BUENOS AIRES, BRASILIA, MONTEVIDEO
CAI
JRS
JED
THR
DXB
KBL
KHI
DEL
DAC
RGN
BKK
HKG
CAIRO
JERUSALEM
JEDDAH
TEHRAN
DUBAI
KABUL
KARACHI
DELHI
DHAKA
YANGON
BANGKOK
HONG KONG
+03
+3.5
+04
+4.5
+05
+5.5
+06
+6.5
+07
+08
TYO
ADL
SYD
NOU
WLG
TOKYO
ADELAIDE
SYDNEY
NOUMEA
WELLINGTON
+09
+9.5
+10
+11
+12
City Code
–––
HNL
ANC
LAX
[Alarm On Indicator/Hourly Time Signal On Indicator]
Both ON
F
Stop
(b) Split time measurement
JR
JR
JF
F
Start
Split
Split release Stop
Minutes
3. Press F to increase the setting or R to decrease it. Holding down either button
changes the setting at high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning (no indicator) or afternoon (P indicator).
4. After you set the alarm time, press A to return to the Alarm Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
J
LONDON
PARIS
+01
+02
* Based on data as of June 1998.
PRAIA
DUBLIN, LISBON, CASABLANCA, DAKAR,
ABIDJAN
MILAN, ROME, MADRID, AMSTERDAM,
ALGIERS, HAMBURG, FRANKFURT, VIENNA,
STOCKHOLM, BERLIN
ATHENS, HELSINKI, ISTANBUL, BEIRUT,
DAMASCUS, CAPE TOWN
KUWAIT, RIYADH, ADEN, ADDIS ABABA, NAIROBI
SHIRAZ
ABU DHABI, MUSCAT
MUMBAI, CALCUTTA
COLOMBO
JAKARTA, PHNOM PENH, HANOI, VIENTIANE
SINGAPORE, KUALA LUMPUR, BEIJING, TAIPEI,
MANILA, PERTH, ULAANBAATAR
SEOUL, PYONGYANG
DARWIN
MELBOURNE, GUAM, RABAUL
PORT VILA
CHRISTCHURCH, NADI, NAURU ISLAND