Casio 1965 Watch User Manual

Module No.1565/1965
1565/1965-1
GENERAL GUIDE
• If the contents of the display seem to be continually changing, see “AUTO DISPLAY FUNCTION” for information on how to stop it.
• Press C to change from mode to mode.
Timekeeping Mode
Day of The
Week Display
Telememo Mode
Stopwatch Mode
Alarm Mode
Time Graph
Display
Press D
-
-
TIMEKEEPING MODE
Month – Date
Day of week
Hour
Seconds
• In the Timekeeping Mode, press B to activate the EL
backlight and display animated graphics for about 3 seconds.
• Press D in the Timekeeping Mode to switch between
the 12-hour and 24-hour formats. With the 12-hour formark along with the curmat, the display shows the
rent day of the week. With the 24-hour format, the display shows a time graph for the current date.
• There are three different time graph formats that change
automatically in accordance with the current relationship between an alarm time setting and the current time.
Minutes
PM indicator
5. After you set the time and date, press A to return to the Timekeeping Mode.
• The day of week is automatically set in accordance with the date.
• The date can be set within the range of January 1, 1995 to December 31, 2039.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
About the backlight
In the Timekeeping Mode, press B to illuminate the display for about 3 seconds.
• The backlight of the watch employs an electro-luminescent (EL) light, which loses
illuminating power after very long use.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch will emit an audible sound whenever the display is illuminated. This is
caused by a transistor that vibrates when the EL panel lights up. It does not indicate malfunction of the watch.
• The backlight automatically turns off whenever an alarm sounds.
No Alarm Time Setting for Current Date
Month – Date
TELEMEMO MODE
Time graph
Caution
The following causes all data stored in memory to be deleted. Be sure to always
keep separate written copies of all important data.
• Malfunction or repairs
• Dead battery
• Battery replacement
Alarm Time Setting for Current Date
Appointment icon
Time graph
Appointment
time indicator
An appointment icon appears on the display and the time
graph hour for which the alarm is set flashes. The time
graph shows how long before the alarm time will be
reached.
In no event will CASIO be liable for loss of data or any damages arising out of
such loss.
The Telememo Mode lets you store up to
20 pages of name, telephone number, and
cell phone (or pager) number data. You can
recall data by scrolling through it on the display.
• The number of unused pages still available for storage of data appears on the display every time you enter the Telememo
Mode.
• You can input up to eight characters in
the text area, and 12 digits in each of the
two (telephone and cell phone) number
areas.
• The data item on the display when you
exit the Telememo Mode appears first the
next time you enter the Telememo Mode.
Mode indicator
Remaining
memory
Name
Month – Date
Alarm Time Setting Within the Hour
Appointment icon
Time graph
Appointment
time indicator
One hour before an alarm time is reached, a tone sounds
and the time graph format changes, replacing the month
and day with a countdown of the minutes and seconds
left until the alarm time is reached.
Telephone
number
[New Data Display]
To input new Telememo data
1. In the Telememo Mode, press D or B until the New
data display appears.
• The new data display is the one that is blank (contains
no name and telephone number).
• If there is no Telememo data stored in memory yet, the
new data display appears as soon as you enter the Telememo Mode.
” appears on the display, it
• If the message “
means that memory is full. To store more data, you will
first
have
to
delete
some
of
the data.
Number area
2. Hold down A and a cursor appears in the text area.
3. Use D or B to input a character at the cursor position. The character changes in
the following sequence. Holding down either button changes the character at high
speed.
Text area
Remaining minutes
and seconds
To set the time and date
1. Hold down A while in the Timekeeping Mode. The seconds digits flash on the
display because they are selected .
2. Press C to change the selection in the following sequence.
Press
(Space)
A to Z
0 to 9
Press
Seconds
Hour
Animated Graphic
Minutes
Year
Day
Month
3. While the seconds digits are selected (flashing), press D to reset the seconds to
00. If you press D while the seconds count is in the range of 30 to 59, the seconds
are reset to 00 and 1 is added to the minutes. If the seconds count is in the range
of 00 to 29, the minutes count is unchanged.
4. While any other digits (besides seconds) are selected (flashing), press D to increase the number or B to decrease it. Holding down either button changes the
current selection at high speed.
• While the animated graphic is flashing, you can select one of the following graphics. The animated graphic you select appears on the display whenever you turn on
the EL backlight in the Timekeeping Mode.
[Module 1565]
1. Random selection of 2, 3, or 4.
2. DANCE
3. DJ
4. LOVE
[Module 1965]
1. Random selection of 2, 3, or 4.
2. LOVERS A
3. LOVERS B
4. LOVERS C
4. After you select the character you want, press C to advance the cursor to the right.
• Repeat 3 and 4 until you complete name input.
• You can input up to 8 characters in the name area.
5. After the name input is through, use C to move the cursor to the telephone number
area.
6. While the cursor is in the telephone number area, use B or D to input a number
you want. The character changes in the following sequence. Holding down either
button changes the character at high speed.
Press
– (Hyphen)
0 to 9
(Space)
Press
7. After you select the character you want, press C to advance the cursor to the right.
• Repeat 6 and 7 until you complete number input.
1565/1965-2
8. After you input the telephone number you want, use C to move the cursor to the
cell phone number area.
indicator indicates the cell phone display.
• The
• Input the cell phone number using the same procedure as you did for the telephone
number.
• If you don’t want to input a cell phone number, proceed from step 9 without inputting anything.
9. After inputting your data, press A to store it and return to the Telememo Mode.
” appears on the display
• When you press A to store data, the message “
for a few seconds. After the sort operation is complete, the normal Telememo
Mode display (without the cursor) appears.
• The text area of the display can show only five characters at a time, so longer text
scrolls continuously from right to left.
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning A or afternoon P.
5. While the appointment icon is flashing, press B or D to scroll through the available appointment icons to find the one you want.
Press
A to Z
to
Press
0 to 9
• The types of appointment icon available and their meanings are shown below.
Alarm
Music
In the Telememo Mode, press D to scroll forward through stored data items or B to
scroll in reverse.
• Holding down either button scrolls through the data at high speed.
Time
Doctor
Telephone
Birthday
To edit Telememo data items
Date
Travel
Inquiry
Dining
Good news
Money
To recall Telememo data
1. In the Telememo Mode, scroll through the data items and display the one you want
to edit.
2. Hold down A and a cursor appears in the text area.
3. Use C to move the cursor to the character you want to change.
4. Change the character.
• See “To input new Telememo data” for details.
5. After making the changes that you want, press A to store it and return to the
Telememo Mode.
To delete Telememo data
1. In the Telememo Mode, scroll through the data items and display the one you want
to delete.
2. Hold down A and a cursor appears in the text area.
3. Press B and D at the same time to delete the data item.
• At this time the cursor appears in the text area, ready for input.
4. Input data or press A to return to the Telememo Mode.
Bad news
• The appointment icon you select appears on the display when the alarm is reached.
The appointment icons serve as reminders to help you remember what the alarm is
for.
6. After you finish inputting data, press A to return to the Alarm Mode.
To stop an alarm once it starts to sound
Press any button to stop an alarm when it starts to sounds. The appointment icon for
the alarm will remain in the text area of the display for about 20 seconds.
To switch an Alarm and Hourly Time Signal on and off
ALARM MODE
Mode indicator
You can set five independent alarms with
the hour, minutes, month, date, day of the
1. In the Alarm Mode, press D to select an alarm or the Hourly Time Signal.
2. When the alarm or Hourly Time Signal you want is selected, press B to switch it on
and off.
... indicates alarm is ON
........ indicates Hourly Time Signal is ON
Month – Date week and appointment icon. You can even
Appointment
icon
?
Alarm on indicator
Hour
Alarm No.
input character that appears on the display
to remind you of the purpose of each alarm.
Use the Alarm Mode to turn the alarm and
the Hourly Time Signal on and off.
• When an alarm is turned on, an alarm
tone sounds for 20 seconds when the
preset time is reached.
• When the Hourly Time Signal is turned
on, the watch beeps every hour on the
hour.
• If any alarm is on, the Alarm On indicator is shown on the display when you change
to another mode.
To test the alarm
Hold down D while in the Alarm Mode to sound the alarm.
STOPWATCH MODE
Minutes
Mode indicator
The stopwatch Mode lets you measure elapsed
time, split times, and two finishes. The range of
the stopwatch is 23 hours, 59 minutes, 59.99 seconds.
Alarm Types
The Alarm Mode lets you specify hour and minutes, as well as month, day, and day of
the week for alarms. How of an alarm sounds is determined by the items you set.
Items Set
• Hour, minutes only
Alarm sounds at the preset time every day.
• Hour, minutes, month
Alarm sounds at the preset time every day during the specified month.
• Hour, minutes, day
Alarm sounds at the preset time on the specified day every month.
• Hour, minutes, month, day
Alarm sounds at the preset time annually on the specified day.
• Hour, minutes, day of the week
Alarm sounds at the preset time every week on the specified day.
• Hour, minutes, month, day of the week
Alarm sounds at the preset time every week on the specified day during the specified month.
• Hour, minutes, day, day of the week
Alarm sounds at the preset time every time the specified day falls on specified day
of the week.
• Hour, minutes, month, day, day of the week
Alarm sounds at the preset time every time the specified day falls on specified day
of the week in the specified month. Note that this type of setting may result in an
alarm that sounds only one every few years.
To set alarms
1. Press D while in the Alarm Mode to select Alarm 1 through Alarm 5.
Alarm 1
Alarm 2
Hourly Time Signal
Minutes
Hours
Seconds
Minutes
Elapsed time measurement
D
Start
D
Stop
D
Re-start
D
Stop
B
Clear
B
Split release
D
Stop
B
Clear
B
Split release
Record time of
second runner.
B
Clear
Split time measurement
D
Start
B
Split
Split time and 1st-2nd place times
D
Start
B
Split
First runner
finishes.
Alarm 4
Alarm 3
D
Stop
Second runner
finishes.
Release time of
first runner.
Alarm 5
2. After you select an alarm, hold down A. The hour digits flash on the display because they are selected.
• At this time, the alarm is automatically switched on.
3. Press C to change the selection in the following sequence.
Hour
1/100 second
Month
AUTO DISPLAY FUNCTION
The Auto Display function of this watch continually changes the contents of the display. Note that you cannot use any of the watch’s other functions while the Auto
Display function is operating.
Day
To turn the Auto Display on
Appointment icon
Day of Week
4. Press D to increase the selected digits and B to decrease them. Holding down
either button changes the selection at high speed.
• To set an alarm that does not include a month, set - for the month. Press D or B
until the - mark appears (between 12 and 1) while the month digits are flashing.
• To set an alarm that does not include a date, set - - for the date. Press D or B until
the - - mark appears (between 31 and 1) while the date digits are flashing.
• To set an alarm that does not include a day of week, set - - - for the day of week.
and
) while the
Press D or B until the - - - mark appears (between
day of week digits are flashing.
Hold down C for about two or three seconds in any mode.
To turn the Auto Display off
Hold down C for about two or three seconds. At this time the watch is in the Timekeeping Mode.
Note
The Auto Display function cannot be performed while you are making settings (i.e.
while digits or other setting are flashing on the display).
Download PDF

advertising