Casio 2115 Watch User Manual

Module No. 1950/2115
1950/2115-1
GENERAL GUIDE
• Press C to change from mode to mode.
• After you perform an operation in any mode, pressing C returns to the Timekeeping Mode.
• If you do not press any button for a few minutes while making settings in any mode (indicated when settings are flashing), the watch automatically clears the setting screen (settings stop
flashing) and returns to the normal display for the mode you are in.
• This watch returns to the Timekeeping Mode whenever you hold down the C button for one or two seconds. If you ever lose track of what mode you are in or what you should do next,
hold down C to return to normal timekeeping.
The operational procedures for Modules 1950 and 2115 are identical. All of
• In any mode press L to illuminate the display.
the illustrations in this manual show Module 1950.
Countdown Alarm Mode
Timekeeping Mode
[Module 2115]
Alarm Mode
Dual Time Mode
[Module 1950]
TIMEKEEPING MODE
To set the time and date
PM indicator
1. Hold down A while in the Timekeeping Mode until the
seconds digits flash on the display because they are
selected.
2. Press C to change the selection in the following sequence.
Day of week
Month - Day
Seconds
Minutes
Hour
12/24-Hour Format
Day of week
Hour
Stopwatch Mode
Day
Month
Seconds
Minutes
3. While the seconds digits are selected (flashing), press D to reset the seconds to
00. If you press D while the seconds count is in the range of 30 to 59, the seconds
are reset to 00 and 1 is added to the minutes. If the seconds count is in the range
of 00 to 29, the minutes count is unchanged.
4. While any other digits (beside seconds) are selected (flashing), press D to increase the number or B to decrease it. While the 12/24-hour format setting is
selected, press D or B to toggle it between 12 and 24. While the day of the week
is selected (flashing), press D to advance to the next day or B to return to the
previous day.
• Except for when adjusting the seconds or setting the 12/24-hour format, holding
down a button changes the current selection at high speed.
• When the 12-hour format is selected, the indicator P appears on the display to
indicate “P.M.” times. There is no indicator for “A.M.” times.
• When the 24-hour format is selected, the indicator 24 appears on the display.
5. After you set the time and date, press A to return to the Timekeeping Mode.
• The auto light switch indicator is shown on the display in all modes while the auto
light switch function is on.
• In order to protect against running down the battery, the auto light switch function is
automatically turned off approximately three hours after you turn it on. Repeat the
above procedure to turn the auto light switch function back on if you want.
• Pressing L while in the Timekeeping Mode illuminates the display, regardless of
the auto light switch’s on/off setting.
Caution
• The backlight of this watch employs an electro-luminescent (EL) light, which loses
its illuminating power after very long term use.
• Frequent use of the backlight shortens the battery life.
• The watch emits an audible sound whenever the display is illuminated. This is because the EL light vibrates slightly when lit. It does not indicate malfunction of the
watch.
Warning!
• Never try to read your watch when mountain climbing or hiking in areas that
are dark or in areas with poor footing. Doing so is dangerous and can result
in serious personal injury.
• Never try to read your watch when running where there is the danger of accidents, especially in locations where there might be vehicular or pedestrian
traffic. Doing so is dangerous and can result in serious personal injury.
• Never try to read your watch when riding on a bicycle or when operating a
motorcycle or any other motor vehicle. Doing so is dangerous and can result
in a traffic accident and serious personal injury.
• When you are wearing the watch, make sure that its auto light switch function
is turned off before riding on a bicycle or operating a motorcycle or any other
motor vehicle.
Sudden and unintended operation of the auto light switch can create a distraction, which can result in a traffic accident and serious personal injury.
COUNTDOWN ALARM MODE
Progress beeper on
indicator
The countdown alarm can be set within a range of 1 second to 24 hours. When the countdown reaches zero, an
Auto repeat on indicator alarm sounds for 10 seconds or until you press any button.
ABOUT THE BACKLIGHT
Current time
About the Auto Light Switch Function
To set the countdown start time
When the auto light switch function is turned on, the backlight automatically turns on
for two seconds under the conditions described below. Avoid wearing the watch on
the inside of your wrist. Doing so causes the auto light switch to operate when not
needed, which shortens battery life.
1. Hold down A while in the Countdown Alarm Mode. The
hours digits flash on the display because they are selected.
2. Press C to change the selection in the following sequence.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you approximately 40 degrees causes the backlight to illuminate.
Minutes
40°
Parallel to ground
• The backlight may not illuminate if the face of the watch is more than 15 degrees off
parallel to the left or right. Make sure that the back of your hand is parallel to the
ground.
Parallel to ground
More than 15 degrees too
high
More than 15 degrees
too low
• Static electricity or magnetic force can interfere with proper operation of the auto
backlight function. If the auto backlight does not illuminate, try moving the watch
back to the starting position (parallel with the ground) and then tilt it back toward
you again. If this does not work, drop your arm all the way down so it hangs at your
side, and then bring it back up again.
• Under certain conditions the backlight may not light until about one second or less
after turning the face of the watch towards you. This does not necessarily indicate
malfunction of the backlight.
To switch the auto light switch function on and off
In the Timekeeping Mode, hold down B for one or two seconds to turn the auto light
switch function on and off.
Auto light switch
indicator
Hold down B .
ON
OFF
1/10
Seconds
Seconds
Hour
Minutes
Seconds
Mode indicator
3. Press D to increase the selected number or B to decrease it. Holding down either
button changes the selection at high speed.
• Press D and B at the same time to clear the starting time to 0:00' 00".
• To set the starting value of the countdown time to 24 hours, set 0:00' 00".
4. After you set the countdown start time, press A twice to return to the Countdown
Alarm Mode.
To use the countdown alarm
1. Press D while in the Countdown Alarm Mode to start the countdown alarm.
2. Press D again to stop the countdown alarm.
• You can resume countdown alarm operation by pressing D .
3. Stop the countdown alarm and then press B to reset the countdown time to its
starting value.
• When the end of the countdown is reached and auto repeat timing is off, the alarm
sounds for 10 seconds or until you stop the alarm by pressing any button. Countdown timing stops and the countdown time is automatically reset to its starting
value after the alarm stops.
To switch auto repeat timing and the progress beeper on and off
1. Hold down A while in the Countdown Alarm Mode. The hour digits flash on the
display because they are selected. Press A again to move the flashing to the auto
repeat ON/OFF setting.
2. Press D or B to toggle auto repeat on ( ) and off.
3. Press C to move the flashing to the progress beeper ON/OFF setting.
4. Press D or B to toggle the progress beeper on (
) and off.
5. Press A to return to the Countdown Alarm Mode.
• When the end of the countdown is reached while auto repeat is on, the alarm sounds,
but the countdown restarts from the beginning without stopping. You can stop the
countdown by pressing D and manually reset to the start time by pressing B.
• If you set a starting time of 10 seconds or less and have Auto Repeat turned on, the
countdown alarm tone (which normally sounds for 10 seconds) sounds for only one
second.
• When the progress beeper is turned on, the watch beeps as the countdown time
passes the 10, 5, 4, 3, 2, and 1-minute marks, and the 50, 40, 30, 20, 10, 5, 4, 3, 2,
and 1-second marks.
1950/2115-2
STOPWATCH MODE
Target time on indicator
Current time
ALARM MODE
The Stopwatch Mode lets you measure elapsed time, split
times, and two finishes. The range of the stopwatch is 23
hour, 59 minutes, 59.99 seconds. You can also have an
alarm sound when a target time is reached. The Stopwatch Mode also features an Auto-Start function.
Alarm on indicator When the Daily Alarm is switched on, the alarm sounds
Hourly time signal
on indicator
Current time
for 20 seconds at the preset time each day. Press any
button to stop the alarm after it starts to sound. When the
Hourly Time Signal is on, the watch beeps every hour on
the hour.
To set the alarm time
Minutes
1. Hold down A until the hour digits start to flash on the
display. The hour digits flash because they are selected.
• This operation will switch the Daily Alarm on automatically.
2. Press C to change the selection in the following sequence.
1/100 Seconds
Seconds
Hour
Mode indicator
(a) Elapsed time measurement
Start
Stop
Re-start
Stop
Clear
Split release
Stop
Clear
(b) Split time measurement
Start
Split
Hour
Minutes
3. Press D to increase the selected digits and B to decrease them. Holding down
either button changes the selection at high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning (no indicator) or afternoon (P).
4. After you set the alarm time, press A to return to the Alarm Mode.
To turn the daily alarm and hourly time signal on and off
Press B while in the Alarm Mode to change the status of the daily alarm and hourly
time signal in the following sequence.
(c) Split time and 1st-2nd place times
Start
Minutes
Mode indicator
Split
Stop
Split release
First runner
finishes.
Second runner
finishes.
Record time of
first runner.
Record time of
second runner.
Clear
Both OFF
About the Auto-Start function
Daily Alarm
Only
Hourly Time
Signal Only
Both ON
With the Auto-Start function, the watch performs a 5-second countdown. When the
countdown reaches zero, stopwatch operation starts automatically. During the final
three seconds of the countdown, a beeper sounds with each second.
• The alarm on indicator (
) and the Hourly Time Signal on indicator (
on the display in all modes while these functions are turned on.
To turn the Auto-Start function on and off
While the display is showing all zeros in the Stopwatch Mode, press B to toggle it on
and off.
• The indicator AUTO-ST appears and 05 is shown in the upper display while AutoStart is turned on. The AUTO-ST indicator is not shown and the upper part of the
display shows the current time when Auto-Start is turned off.
To test the alarm sound
Hold down B while in the Alarm Mode to sound the alarm.
• Note that pressing B also changes the alarm and the hourly time signal ON/OFF
settings.
DUAL TIME MODE
About the Target Time function
With the Target Time function, an alarm sounds for ten seconds whenever the time
being kept by the stopwatch reaches a target time you have preset.
Current time
To set the Target Time and to turn it on and off
1. While the display is showing all zeros in the Stopwatch
Target time on indicator
Mode, hold down A , and the hour digit of the target
Hour
time starts to flash because it is selected.
2. Press C to change the selection in the following sequence.
Hour
) are shown
Minutes
3. Press D to increase the selected number or B to decrease it. Holding down either button changes the se0:00' 00".
4. Press A to move the flashing to the target time ON/OFF setting.
5. D or B to toggle the target time on and off.
6. Press A to return to the Stopwatch Mode.
Important!
The alarm will not sound if you do not turn on the target time.
• Press A , C or L to stop the alarm after it starts to sound.
To set the Dual Time
1. Hold down A while in the Dual Time Mode. The hour
digits flash on the display because they are selected.
2. Press C to change the selection in the following sequence.
Seconds
Minutes
Seconds
lection at high speed.
• Press D and B at the same time to clear the setting to
Mode indicator
The Dual Time Mode lets you keep track of the time in
another time zone. You can also select the timekeeping
format (12-hour or 24-hour) separately from the Timekeeping Mode.
Hour
Hour
Minutes
Minutes
Mode indicator
3. Press D to increase the selected digits and B to decrease them. Holding down either button changes the
selection at high speed.
4. After you set the time, press A to return to the Dual Time Mode.
• In the Dual Time Mode, the seconds count is synchronized with the seconds count
of the Timekeeping Mode.
• In the Dual Time Mode, press B to toggle between the 12-hour and 24-hour formats.