Casio 2358-1 Watch User Manual

Module No. 2358
2358-1
GETTING ACQUAINTED
Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to carefully read this manual and keep it on hand for later reference when necessary.
• Button operations are indicated using the letters shown in the illustration.
• Each section of this manual provides you with the information you need to perform operations in each mode. Further details and technical information can be
found in the “REFERENCE” section.
Crown
GENERAL GUIDE
• Press C to change from mode to mode.
• In any mode, press L to illuminate the display.
• If the digital display of your watch is continuously changing, see “Auto Display Function” for information on how to stop it.
Timekeeping Mode
Telememo Mode
World Time Mode
Alarm Mode
Stopwatch Mode
Press C.
Daylight Saving Time (DST)
TIMEKEEPING
Use the Timekeeping Mode to set and view the current time and date.
• In the Timekeeping Mode, press D to change the display format as shown below.
Date
Day of week
Date/Time
Year
Month – Day
Analog
World map
PM
indicator
Hour hand
Minute hand
Seconds
Hour : Minutes
Second hand
• The time zone that corresponds to your Home City code (see below) flashes on the
Date/Time screen’s world map.
Read This Before You Set the Time and Date !
The digital times displayed in the Timekeeping Mode and World Time Mode are
linked. Because of this, make sure you select a city code for your Home City (the city
where you normally use the watch).
• This watch features separate digital and analog timekeeping. Note that the digital
time and analog time are independent of each other, and must be set separately.
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the
City code
second digits start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Seconds
Day
DST
Month
City Code
Year
Daylight Saving Time advances the time setting by one hour from Standard Time.
Remember that not all countries or even local areas use Daylight Saving Time.
To toggle the Timekeeping Mode time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the
second digits start to flash, which indicates the setting
screen.
2. Press C to move the flashing to the DST On/Off
setting.
3. Press D to toggle between Daylight Saving Time and
standard time.
• Note that you cannot switch between standard time
GMT differential
and Daylight Saving Time while
is selected as
the city code.
4. Press A to exit the setting screen.
• The DST indicator appears on the display to indicate
that daylight saving time is turned on.
To set the analog time
1. Pull the crown out.
• This causes the second hand to stop.
2. Set the minute and hour hands by turning the crown.
3. Push the crown back in to restart timekeeping.
TELEMEMO
Remaining memory
Telememo lets you store up to 30 records, each
containing name and telephone number data. Records
are automatically sorted based on the characters of the
name. You can recall records by scrolling through them
on the display.
• See “CHARACTER LIST” for details on how the watch
sorts records.
• The name can show only three characters at a time, so
longer text scrolls continuously from right to left.
• All of the operations in this section are performed in the
Telememo Mode, which you enter by pressing C.
Number of records stored
Hour
Minutes
3. When the setting you want to change is flashing, press D to change it as described
below.
Setting
Seconds
Do this...
Press D to reset to 00.
DST
Press D to toggle between Daylight Saving Time and standard
time. See “Daylight Saving Time (DST)” for details.
City Code, Hour,
Minutes, Year,
Month, Day
Press D(+) to change the setting.
• See “CITY CODE TABLE” for a complete list of available codes.
• Pressing D while the seconds count is in the range of 30 to 59 resets the
seconds to 00 and adds 1 to the minutes. In the range of 00 to 29, the minutes
count is unchanged.
4. Press A to exit the setting screen.
Note
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
• The year can be set in the range of 2000 to 2039.
• The watch’s built-in full automatic calendar automatically makes allowances for
different month lengths and leap years. Once you set the date, there should be no
reason to change it except after you have the watch’s battery replaced.
To toggle between 12-hour and 24-hour timekeeping
While the Date/Time screen is on the display in the Timekeeping Mode, press B to
toggle between 12-hour and 24-hour timekeeping for the digital time.
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, with 24
indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is also
applied in all other modes.
Name
Telephone number
To create a new Telememo record
1. In the Telememo Mode, press B or D until the new
Text area
data screen appears.
• The new data screen is the one that is blank (contains
no name and telephone number).
• If the message
appears on the display, it
means that memory is full. To store another record,
you will first have to delete some of the records stored
in memory.
2. Hold down A until the flashing cursor ( ) appears in
the text area of the display, which indicates the setting
screen.
Number area
3. Use B and D to change the character at the cursor
New Data screen
position in the text area. The character changes in the
following sequence.
Press
(space)
.
Press
to
.
to
2358-2
4. When the character you want is at the cursor position, press C to move the cursor
to the right.
5. Repeat steps 3 and 4 until the name is complete.
• You can input up to eight characters for the name.
6. After you input the name, press C as many times as necessary to move the cursor
to the number area.
• You can input up to eight characters for the name. When the cursor is located at
the eighth space of the name, moving the cursor to the right causes it to jump to
the first digit of the number. When the cursor is at the 12th digit of the number,
moving it to the right (by pressing C) causes it to jump to the first character in the
name.
7. Use B and D to change the character (hyphen, number, or space) at the cursor
position in the number area. The character changes in the following sequence.
Press
.
Press
.
to
(space)
ALARM
Hourly time signal on You can set a Daily Alarm. When an alarm is turned on,
indicator
the alarm tone sounds when the alarm time is reached.
Timekeeping Mode time
Alarm time
Alarm on indicator
8. When the character you want is at the cursor position, press C to move the cursor
to the right.
9. Repeat steps 7 and 8 until you complete number input.
• You can input up to 12 digits for the number.
• The number initially contains all hyphens. You can leave the hyphens or replace
them with numbers or spaces.
10. Press A to store your data and return to the Telememo record screen (without
the cursor).
• When you press A to store data, the message
may appear on the display
for a while, indicating that data is being sorted. After the sort operation is
complete, the Telememo record screen appears.
To set the alarm time
To recall Telememo records
In the Telememo Mode, use D(+) and B(–) to scroll through Telememo records on
the display.
Daily Alarm Operation
To edit a Telememo record
1. In the Telememo Mode, scroll through the records and display the one you want to
edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use C to move the flashing to the character you want to change.
4. Use B and D to change the character.
• For details on inputting characters, see “To create a new Telememo record” (step
3 for name input and 7 for number input).
5. After making the changes that you want, press A to store them and return to the
Telememo record screen.
1. In the Alarm Mode, hold down A until the hour digits of
the alarm time start to flash.
• This automatically turns on the alarm.
2. Press C to move the flashing between the hour and
minutes.
3. While a setting is flashing, use D(+) to change it.
• When setting the alarm time using the 12-hour format,
take care to set the time correctly as a.m. (no
indicator) or p.m. (P indicator).
4. Press A to return to the alarm display screen.
The alarm sounds at the preset time each day for about 20 seconds, or until you stop
it by pressing any button.
• The alarm and hourly time signal sound in all modes.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn the Daily Alarm and Hourly Time Signal on and off
In the Alarm Mode, press B to cycle through the on and off settings as shown below.
Alarm On Indicator/Hourly Time Signal On Indicator
Alarm On
Signal On
To delete a Telememo record
1. In the Telememo Mode, scroll through the records and display the one you want to
delete.
2. Hold down A until the flashing cursor appears on the display.
3. Press B and D at the same time to delete the record.
• The message
appears to indicate that the record is being deleted. After the
record is deleted, the cursor appears on the display, ready for input.
4. Input data or press A to return to the Telememo record screen.
Alarm Off
Signal Off
WORLD TIME
World map
World Time shows the current time in 27 cities (29 time
zones) around the world.
• For full information on city codes, see the “CITY CODE
TABLE”.
• The time zone that corresponds to the selected city
code flashes on the world map.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time in another city code
While in the World Time Mode, press D to scroll forward
through the city codes (time zones) and B to scroll back.
• If the current time shown for a city is wrong, check your
Timekeeping Mode time and Home City code settings
and make the necessary changes.
City code
Current time in the
selected city code
To toggle a city code time between standard time and Daylight Saving Time
1. In the World Time Mode, use B and D to display the
city code (time zone) whose standard time/Daylight
Saving Time setting you want to change.
2. Hold down A for about two seconds to toggle Daylight
Saving Time (DST displayed) and standard time (DST
not displayed).
• The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
• Note that the DST/Standard Time setting affects only
the currently displayed city code. Other city codes are
not affected.
• Note that you cannot switch between standard time
and Daylight Saving Time while
is selected as
the city code.
Alarm On
Signal Off
Alarm Off
Signal On
STOPWATCH
1/100 second
GMT differential
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• The alarm and Hourly Time Signal operate in
accordance with the current digital time (Timekeeping
Mode time).
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Hours
Seconds
Minutes
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours, 59
minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
• The time on the screen may not appear to stop
immediately when you press the button to stop an
elapsed time operation or perform a split time operation
in the Stopwatch Mode. Despite this, the time recorded
by your button operation is accurate.
To measure times with the stopwatch
Elapsed Time
Start
Stop
Re-start
Stop
Clear
Split
Split release
Stop
Clear
Split
Stop
Split release
Clear
First runner
finishes.
Second runner
finishes.
Record time of
first runner.
Record time of
second runner.
Split Time
Start
Two Finishes
Start
2358-3
REFERENCE
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto Display Function
CHARACTER LIST
Auto Display function of this watch continually changes
the contents of the digital display. Note that you cannot
use any of the watch’s other functions while the Auto
Display function is operating.
To turn the Auto Display off
Hold down C for about two seconds until the watch
beeps.
To turn the Auto Display on
Hold down C for one to two seconds until the watch beeps.
• Note that the Auto Display function cannot be performed while you are making
settings.
1
(space)
11
J
21
T
31
3
2
A
12
K
22
U
32
4
3
B
13
L
23
V
33
5
4
C
14
M
24
W
34
6
5
D
15
N
25
X
35
7
6
E
16
O
26
Y
36
8
7
F
17
P
27
Z
37
9
8
G
18
Q
28
0
38
.
9
H
19
R
29
1
39
-
10
I
20
S
30
2
40
/
Auto Return Features
• If you leave a screen with flashing digits or a cursor on the display for two or three
minutes without performing any operation, the watch automatically saves anything
you have input up to that point and exits the setting screen.
• If you leave the watch in Telememo or Alarm Mode for about two or three minutes
without performing any operation, it automatically changes to the Timekeeping
Mode.
CITY CODE TABLE
City
City
Code
–––
HNL
HONOLULU
ANC ANCHORAGE
GMT
Differential
–11
–10
–9
Data and Setting Scrolling
LAX LOS ANGELES
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
DEN
DENVER
–7
CHI
CHICAGO
–6
NYC
NEW YORK
–5
Initial Screens
When you enter the Telememo or World Time Mode, the data you were viewing when
you last exited the mode appears first.
World Time
• The current time in all World Time Mode cities is calculated in accordance with the
Greenwich Mean Time (GMT) differential for each city, based on the current Home
City time setting in the Timekeeping Mode.
• Daylight Saving Time (DST) advances the time setting by one hour from Standard
Time. Remember that not all countries or even local areas use Daylight Saving
Time.
• The GMT differential is the time difference of the time zone where the city is located
from Greenwich Mean Time.
• GMT differential is calculated by this watch based on Universal Time Coordinated
(UTC) data.
Backlight Precautions
In any mode, press L to illuminate the display for about two seconds.
• The electro-luminescent panel that provides illumination loses power after very long
use.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• The backlight automatically turns off whenever an alarm sounds.
• Frequent use of the backlight shortens the battery life.
–8
Other major cities in same time zone
PAGO PAGO
PAPEETE
NOME
SAN FRANCISCO, LAS VEGAS, VANCOUVER, SEATTLE,
DAWSON CITY
EL PASO, EDMONTON
HOUSTON, DALLAS/FORT WORTH, NEW ORLEANS,
MEXICO CITY, WINNIPEG
MONTREAL, DETROIT, MIAMI, BOSTON, PANAMA CITY,
HAVANA, LIMA, BOGOTA
LA PAZ, SANTIAGO, PORT OF SPAIN
SAO PAULO, BUENOS AIRES, BRASILIA, MONTEVIDEO
CCS
CARACAS
RIO RIO DE JANEIRO
–––
–––
GMT
LONDON
LON
–4
–3
–2
–1
+0
DUBLIN, LISBON, CASABLANCA, DAKAR, ABIDJAN
PAR
PARIS
+1
CAI
JRS
JED
THR
DXB
KBL
KHI
DEL
DAC
RGN
BKK
CAIRO
JERUSALEM
JEDDAH
TEHRAN
DUBAI
KABUL
KARACHI
DELHI
DHAKA
YANGON
BANGKOK
+2
MILAN, ROME, MADRID, AMSTERDAM, ALGIERS,
HAMBURG, FRANKFURT, VIENNA, STOCKHOLM, BERLIN
ATHENS, HELSINKI, ISTANBUL, BEIRUT, DAMASCUS,
CAPE TOWN
KUWAIT, RIYADH, ADEN, ADDIS ABABA, NAIROBI, MOSCOW
SHIRAZ
ABU DHABI, MUSCAT
HKG
HONG KONG
+8
+3
+3.5
+4
+4.5
+5
+5.5
+6
+6.5
+7
TYO
TOKYO
+9
ADL
ADELAIDE
+9.5
SYD
SYDNEY
+10
NOU
NOUMEA
+11
WLG WELLINGTON
+12
*Based on data as of June 2000.
PRAIA
MALE
MUMBAI, CALCUTTA
COLOMBO
JAKARTA, PHNOM PENH, HANOI, VIENTIANE
SINGAPORE, KUALA LUMPUR, BEIJING, TAIPEI, MANILA,
PERTH, ULAANBAATAR
SEOUL, PYONGYANG
DARWIN
MELBOURNE, GUAM, RABAUL
PORT VILA
CHRISTCHURCH, NADI, NAURU ISLAND