Casio 2515 Watch User Manual

MO0308-EA
Operation Guide 2515
About This Manual
(Light)
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
Alarm Mode
General Guide
Stopwatch Mode
▲
▲
• Press B to change from mode to mode.
• In any mode, press L to illuminate the display.
Data Bank Mode
Timekeeping Mode
▲
▲
Countdown Timer Mode
Dual Time Mode
▲
▲
Press B.
Timekeeping
Use the Timekeeping Mode to set the time and date. You
Daylight Saving Time (DST)
Mode screen from the Timekeeping Mode.
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
Day of week Hour : Minutes can also view the Dual Time Mode screen or Data Bank
Seconds
Note
This watch is capable of displaying text for the day of the
week in any one of 13 different languages (English,
Portuguese, Spanish, French, Dutch, Danish, German,
Italian, Swedish, Polish, Romanian, Turkish, and Russian).
PM indicator
Year Month–Day
Language indicator
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Use C and B to move the flashing in the sequence
shown below to select other settings.
Press C.
Seconds
Press B.
Year
Month
To toggle the Timekeeping Mode time between DST and Standard Time
Holding down C for about two seconds in the
Timekeeping Mode toggles between Daylight Saving Time
(DST display) and Standard Time (DST not displayed).
• Note that pressing C in the Timekeeping Mode also
toggles between 12-hour timekeeping and 24-hour
timekeeping.
• The DST indicator appears on the display to indicate
that daylight saving time is turned on.
To display the Data Bank screen and Dual Time screen in the Timekeeping Mode
Holding down D in the Timekeeping Mode displays the Dual Time screen. Holding
down E displays the record you were viewing when you last used the Data Bank
Mode.
Dual Time Screen
Day
Data Bank Screen
Hold down D.
Minutes
Hour
Language
• The currently selected language indicator flashes on the display while the
Language (setting) is selected in the above sequence.
3. When the setting you want to change is flashing, use E and D to change it as
described below.
To change this setting
Seconds
Year, Month, Day, Hour,
Minutes
Language
Perform this button operation
Press E to reset to 00.
Use E (+) and D (–) to change the setting.
Use E and D to change the language setting.
• While the language indicator is flashing on the display, use E and D to cycle
through the language indicators as shown below, until the one for the language
you want to select is displayed.
Press E.
Indicator
ENx
POR
ESP
FRA
Press D. NED
Language
English
Portuguese
Spanish
French
Dutch
Indicator
DAN
DEU
ITA
SVE
POL
Hold down E.
Language
Danish
German
Italian
Swedish
Polish
Indicator
RO
T)R
PUC
Language
Romanian
Turkish
Russian
4. Press A to exit the setting screen.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
• See the “Day of the Week List” for information on abbreviations used.
• In addition to the day of the week display, the language setting also affects the type
of characters you can input for the name in the Data Bank Mode.
• Holding down A in the Timekeeping Mode displays the indicator for the currently
selected language. Keeping A depressed for one or two seconds changes to the
Timekeeping Mode setting screen (indicated by the seconds flashing). If you
accidentally display the setting screen, press A again to exit.
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press C to toggle between 12-hour timekeeping (indicated
by A or P on the display), or 24-hour timekeeping.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and the A (AM) indicator appears for times in the range
of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
Data Bank
The Data Bank Mode lets you store up to 30 records,
each containing name and telephone number data.
Records are automatically sorted based on the characters
Name of the name. You can recall records by scrolling through
them on the display.
• The characters you can input for the name depend on
the language you select in the Timekeeping Mode. See
“To set the time and date” for more information.
Changing the language setting does not affect names
that are already stored.
• See “Sort Table” for details on how the watch sorts
records.
• All of the operations in this section are performed in the
Data Bank Mode, which you enter by pressing B.
Telephone number
Remaining
memory
To create a new Data Bank record
1. In the Data Bank Mode, press C to display the new
Name area
data screen.
Number area
• If the new data screen does not appear when you
press C, it means that memory is full. To store
another record, you will first have to delete some of
the records stored in memory.
New Data Screen
2. Hold down A until the flashing cursor (_) appears in
the name area of the display.
3. In the name area, use E and D to cycle through
characters at the cursor position. The characters cycle
in the sequence shown below.
Press E.
(space)
A to Z
(alphabet)
@ to (symbol)
0 to 9
(number)
Press D.
• The above character sequence is for English input. See “Character List” for the
character sequences of other languages.
4. When the character you want is at the cursor position, press C to move the cursor
to the right.
5. Repeat steps 3 and 4 until the name is complete.
• You can input up to eight characters for the name.
1
Operation Guide 2515
6. After you input the name, press C as many times as necessary to move the cursor
to the number area.
• When the cursor is located at the eighth space of the name area, moving the
cursor to the right causes it to jump to the first digit of the number. When the
cursor is at the 15th digit of the number, moving it to the right (by pressing C)
causes it to jump to the first character in the name.
• Pressing C moves the cursor the right, while B moves it to the left.
7. In the number area, use E and D to cycle through numbers and symbols
(hyphen, brackets, space) at the cursor position. The characters cycle in the
sequence shown below.
Press E.
x
0 to 9
[
]
(space)
Press D.
8. When the character you want is at the cursor position, press C to move the cursor
to the right.
9. Repeat steps 7 and 8 until you complete number input.
• You can input up to 15 digits for the number.
• The number initially contains all hyphens. You can leave the hyphens as they are
or replace them with numbers or other symbols (brackets, space).
10. Press A to store your data and return to the Data Bank record screen (without
the cursor).
• When you press A to store data, the name and number you input flash for about
one second as Data Bank records are sorted. After the sort operation is complete,
the Data Bank record screen appears.
• The name can show only three characters at a time, so longer text scrolls
continuously from right to left. The last character is indicated by the symbol after it.
To recall Data Bank records
In the Data Bank Mode, use E (+) and D (–) to scroll through Data Bank records on
the display.
• Pressing E while the last Data Bank record is on the display or D while the first
record is on the display displays the new data screen.
To edit a Data Bank record
1. In the Data Bank Mode, use E (+) and D (–) to scroll through the records and
display the one you want to edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use C (right) and B (left) to move the flashing to the character you want to
change.
4. Use E (forward) and D (back) to change the character.
5. After making the changes that you want, press A to store them and return to the
Data Bank record screen.
To delete a Data Bank record
1. In the Data Bank Mode, use E (+) and D (–) to scroll through the records and
display the one you want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Press B and C at the same time to delete the record.
• The message CLR appears to indicate that the record is being deleted. After the
record is deleted, the cursor appears on the display, ready for input.
4. Input data or press A to return to the Data Bank record screen.
3. Use C and B to move the flashing in the sequence shown below to select other
settings.
Press C.
Minutes
Hour
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm repeats up to seven times
every five minutes until you turn the alarm off or change it to a one-time alarm.
• Pressing any button stops the alarm tone operation.
• Any time you display the setting screen while the Alarm1 screen is on the display,
Alarm1 automatically becomes a one-time alarm.
• Displaying the Timekeeping Mode setting screen during a 5-minute interval between
snooze alarms stops the current snooze alarm operation (but snooze alarm remains
as the alarm type setting).
To test the alarm
In the Alarm Mode, hold down C to sound the alarm.
To turn Alarms 2 through 5 and the hourly time signal on and off
1. In the Alarm Mode, use E and D to select a one-time
Alarm on indicators
alarm (alarm number 2 through 5) or the Hourly Time
Signal.
2. Press C to toggle it on and off.
• The on/off status of Alarms 2 through 5 is shown by
indicators along the bottom of the displays (
= on).
The SIG indicator shows the on (displayed)/off (not
displayed) status of the hourly time signal.
• The alarm on indicators and hourly time signal indicator
are displayed in all modes.
• While an alarm is sounding, the applicable alarm on
Hourly time signal
indicator flashes on the display.
on indicator
To select the operation of Alarm1
1. In the Alarm Mode, use E and D to select Alarm1.
2. Press C to cycle through the available settings in the sequence shown below.
SNZ indicator and Alarm1 on indicator
Press C.
One-time alarm on Snooze alarm on
You can set up to five independent multi-function alarms
Alarm time
with hour, minutes, month, and day. When an alarm is
(Hour : Minutes)
turned on, the alarm tone sounds when the alarm time is
reached. You can select either a one-time alarm or snooze
alarm that repeats up to seven times, every five minutes.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are five alarms numbered1 through 5. You can
configure Alarm1 as a snooze alarm or a one-timealarm. Alarms 2 through 5 can be used as one-time
alarms only.
Timekeeping Alarm date
• Alarm settings (and Hourly Time Signal settings) are
Mode time
(Month–Day)
available in the Alarm Mode, which you enter by
pressing B.
Stopwatch
Hours
Minutes
Seconds
The alarm type is determined by the settings you make, as described below.
Timekeeping
Mode time
1/100 second
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours, 59
minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing B.
• Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
To measure times with the stopwatch
• 1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at the time you set, only during the month you set.
C
• Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
Elapsed Time
Start
➤C
Stop
➤C
Re-start
➤C
Stop
➤A
Clear
➤A
Split
➤A
Split release
➤C
Stop
➤A
Clear
➤C
Stop
➤A
Split release
➤A
Clear
Split Time
C
Start
To set an alarm time
Alarm number
Alarm off
• The SNZ indicator and Alarm1 on indicator are displayed in all modes.
• The SNZ indicator flashes during the 5-minute intervals between alarms.
• The alarm indicator (Alarm1 on and/or SNZ) flashes while the alarm is sounding.
Alarm Types
• Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
Day
4. While a setting is flashing, use E (+) and D (–) to change it.
• To set an alarm that does not include a month (Daily alarm, Monthly alarm), set x
for the month. Use E and D until the x mark appears (between 12 and 1) while
month setting is flashing.
• To set an alarm that does not include a day (Daily alarm, 1-Month alarm), set xx
for the day. Use E and D until the xx mark appears (between the end of the
month and 1) while the day setting is flashing.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarms
Alarm number
Month
Press B.
(SPL displayed)
1. In the Alarm Mode, use E and D to scroll through the
alarm screens until the one whose time you want to set
is displayed.
Press E.
Press D.
Alarm1
Alarm 2
Alarm 3
Time
Signal
Alarm 5
Alarm 4
Two Finishes
C
Start
➤A
Split
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
• Each of the five alarm screens has an alarm number.
The hourly time signal screen does not have an alarm
number.
2. After you select an alarm, hold down A until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
• This operation automatically turns on the alarm.
2
Operation Guide 2515
Countdown Timer
Hours
Minutes
Seconds
Timekeeping Mode time
The countdown timer can be set within a range of 1
minute to 24 hours. An alarm sounds when the countdown
reaches zero.
• Countdown timer functions are available in the
Countdown Timer Mode, which you enter by pressing
B.
To set the countdown start time
1. In the Countdown Timer Mode, hold down A until the
hour setting of the countdown start time starts to flash,
which indicates the setting screen.
2. Press B or C to move the flashing between the hour
and minute settings.
3. While a setting is flashing, use E (+) and D (–) to change it.
• To set the starting value of the countdown time to 24 hours, set 0:00.
4. Press A to exit the setting screen.
To use the countdown timer
Press C while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm sounds for 10 seconds or until
you stop it by pressing any button. The countdown time is automatically reset to its
starting value after the alarm stops.
• Press C while a countdown operation is in progress to pause it. Press C again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing C), and then
press A. This returns the countdown time to its starting value.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
Dual Time
Dual time
(Hour : Minutes Seconds)
The Dual Time Mode lets you keep track of time in a
different time zone. You can select Standard Time or
Daylight Saving Time for the Dual Time Mode time, and a
simple operation lets you view the Timekeeping Mode
screen or Data Bank Mode screen.
• The seconds count of the Dual Time is synchronized
with the seconds count of the Timekeeping Mode.
• All of the operations in this section are performed in the
Dual Time Mode, which you enter by pressing B.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The year can be set in the range of 2000 to 2039.
• The watch’s built-in full automatic calendar automatically makes allowances for
different month lengths and leap years. Once you set the date, there should be no
reason to change it except after you have the watch’s battery replaced.
Backlight Precautions
The backlight uses an LED (light-emitting diode) and a light guide panel that causes
the entire display to glow for easy reading in the dark. In any mode, press L to
illuminate the display for about one second.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The backlight automatically turns off whenever an alarm sounds.
• Frequent use of the backlight shortens the battery life.
Day of the Week List
Sunday
SUN
DOo
DOo
DIo
ZON
SvN
SON
DOo
SiN
NIE
DUo
PAZ
CS
ENx
POR
ESP
FRA
NED
DAN
DEU
ITA
SVE
POL
ROo
TgR
RUS
Monday Tuesday Wednesday Thursday
oON
TUE
WED
THU
SEx
TER
QUA
QUI
LUN
oAR
oIb
JUE
LUN
oAR
oER
JEU
oAA
DIN
WOE
DON
oAN
TIR
ONS
TOR
oON
DIE
oIT
DON
LUN
oAR
oER
xIO
owN
TIS
ONS
TOR
PON
WTO
qRO
CZW
LUN
oAR
oIE
JOI
PZT
SAL
mAR
PER
QO
BT
SR
YT
Friday
FRI
SEX
VIE
VEN
VRI
FRE
FRE
VEN
FRE
PIl
VIN
CUo
QT
Saturday
SAT
SaB
SaB
SAo
ZAT
LvR
SAo
SAB
LiR
SOB
Sjo
CTS
SB
Character List
ENx: (space) A B C D E F x H I J n L o N O P Q R S T U V W X Y Z @ ]
?'.:/+-0123p56q89
Timekeeping Mode time
To set the Dual Time
1. In the Dual Time Mode, hold down A until the hour setting start to flash, which
indicates the setting screen.
2. Press B or C to move the flashing between the hour and minute settings.
3. While a setting is flashing, use E (+) and D (–) to change it.
4. Press A to exit the setting screen.
To toggle Dual Time Mode time between DST and Standard Time
Holding down C for about two seconds in the Dual Time Mode toggles between
Daylight Saving Time (DST display) and Standard Time (DST not displayed).
• The DST indicator on the display indicates that daylight saving time is turned on.
To display the Timekeeping screen and Data Bank screen
Holding down D in the Dual Time Mode displays the Timekeeping screen. Holding
down E displays the record you were viewing when you last used the Data Bank
Mode.
Timekeeping Screen
Data Bank Screen
Hold down D.
Hold down E.
POR: (espaço) A ; ( , h B C ^ D E = [ F x H I > J n L o N O ? ] i P
QRSTU@VWXYZ@]?'.:/+-0123p56q89
ESP: (espacio) A ; B C D E = F x H I > J n L o N ` O ? P Q R S T U @
)VWXYZ@]?'.:/+-0123p56q89
FRA: (espace) A ( , B C ^ D E = a [ c F x H I e d J n L o N O ] g P Q
RSTUbf)VWXYZ@]?'.:/+-0123p56q89
NED: (Spatie) A B C D E F x H I J n L o N O P Q R S T U V W X Y Z @
]?'.:/+-0123p56q89
DAN: (Mellemsrum) A B C D E F x H I J n L o N O P Q R S T U V W X Y
Zuvw@]?'.:/+-0123p56q89
DEU: (Leerzeichen) A h B C D E F x H I J n L o N O i P Q R S T U ) V
WXYZ@]?'.:/+-0123p56q89
ITA: (spazio) A ( B C D E = a F x H I j e J n L o N O ? k P Q R S T
UbVWXYZ@]?'.:/+-0123p56q89
SVE: (Mellanslag) A B C D E F x H I J n L o N O P Q R S T U V W X Y Z
whi@]?'.:/+-0123p56q89
POL: (epacja) A l B C m D E n F x H I J n L o o N p O ? P Q R S q T
UVWXYZrs@]?'.:/+-0123p56q89
ROM: (spa iu) A r , B C D E F x H I e J n L o N O P Q R S s T t U V W
XYZ@]?'.:/+-0123p56q89
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto Display
Auto Display continually changes the contents of the
digital display.
To turn off Auto Display
Press any button (except for L) to turn off Auto Display.
This returns to the Timekeeping Mode.
To turn on Auto Display
Hold down B for about two seconds until the watch
beeps.
• Note that Auto Display cannot be performed while a
setting screen is on the display.
Auto Return Features
• After you perform any button operation (except for the backlight button) in any mode,
pressing B returns directly to the Timekeeping Mode.
• If you leave the watch in the Data Bank Mode for two or three minutes without
performing any operation, it automatically changes to the Timekeeping Mode.
• If you leave a screen with flashing digits or a cursor on the display for two or three
minutes without performing any operation, the watch automatically saves any
settings you have made up to that point and exits the setting screen.
Data and Setting Scrolling
The B, C, D, and E buttons are used in various modes and setting screens to
scroll through data on the display. In most cases, holding down these buttons during a
scroll operation scrolls through the data at high speed.
Initial Screens
When you enter the Data Bank or Alarm Mode, the data you were viewing when you
last exited the mode appears first.
T)R: (bo luk) A B C ^ D E F x y H I t J n L o N O i P Q R S s T U )
VWXYZ@]?'.:/+-0123p56q89
PUC: (npo en) A B C D E F G * I J K L M o O P Q R S T U V W X Y
bciefh@]?'.:/+-0123p56q89
a
Sort Table
1 (space) 13
2
A
14
3
a
15
4
f
16
5
r
17
6
j
18
7
h
19
8
h
20
9
l
21
10
B
22
11
C
23
12
m
24
m
D
E
b
a
[
c
n
F
x
y
H
25
26
27
28
29
30
31
32
33
34
35
36
I
>
j
e
d
t
J
n
L
o
o
N
37
38
39
40
41
42
43
44
45
46
47
48
p
`
O
?
k
l
i
+
g
P
Q
R
49
50
51
52
53
54
55
56
57
58
59
60
S
q
s
T
t
U
@
b
f
)
V
W
61
62
63
64
65
66
67
68
69
70
71
72
X
Y
Z
r
s
u
v
w
h
i
B
C
73
74
75
76
77
78
79
80
81
82
83
84
D
E
F
c
*
I
J
K
L
M
o
O
85
86
87
88
89
90
V
W
X
Y
97
98
99
100
101
102
b
c
d
e
f
h
103
104
105
106
107
108
@
]
?
'
.
:
109
110
111
112
113
114
/
+
0
1
2
115
116
117
118
119
120
3
p
5
6
q
8
121
9
P
Q
R
S
T
U
91
92
93
94
95
96
a
• Character 7 ( h) is for German, character 69 ( h) is for Swedish.
• Character 43 ( i) is for German and Turkish, character 70 ( i) is for Swedish.
• Characters 71 through 102 are for Russian.
3